We purchased a Whirlpool refrigerator in December 2017. Since July 19 we have had the same problem with the refrigerator three times. The technicians don’t know how to fix it and Whirlpool refuses to replace it. The customer service rep was ignorant on the phone and could care less about a problem. Even though there is a lemon law they refuse to replace the refrigerator. We have to defrost the refrigerator every 2 to 3 weeks so will cool down again. Whirlpool is the worst company we have ever dealt with customer service wise. Lowes will not do anything about it because it’s within the first year.

I purchased the model WDF530PAYM0 serial: F14106104 dishwasher. The foremost reason I purchased this was it had nylon racks. I have discovered that the racks are rusting! It is rusting on the ends where nothing can touch it. I am very disappointed that it is advertised having nylon racks and now it is rusting and deteriorating. This dishwasher states racks-nylon, not racks-nylon coated. I just took some pictures of the racks. I decided to look underneath the top rack where the upper spray arm is located. Now I am plain sick! Most of the underneath is rusting. This dishwasher was purchased and installed 2 years ago. I paid $600 and you would assume that something mechanical would quit after years of use on an average of 1 to 2 times per weeks. Not this one...rusting racks and hard telling what damage the rust flaking off during running is causing to the mechanical components. Lesson learned: Their definition of nylon and nylon coated has no difference.....I very much disagree!

On August 16, 2016 I received delivery of an Whirlpool under counter refrigerator that I ordered online from Home Depot. Model # WUR50X24EM. Five months later, on January 10, 2017, it stopped working, I called Whirlpool for repair. They referred me to their service company, I called the service company the same day. They had a repairman out on the following Tuesday, 1/17/17. The repairman said that he will need to contact Whirlpool to order a part. Whirlpool sent him the wrong part. After numerous phone calls no one from Whirlpool could figure out the correct part number. The repairman kept sending over pictures and information on the correct part, but this all went nowhere with Whirlpool.On 2/7/17, I called and started yelling. I had been very patient up to this point. I was finally offered by Whirlpool a parts research to determine exactly which part was needed. Plus a $50 Visa card to appease me. At this point, its been four weeks without a refrigerator and no one from Whirlpool has put any effort towards trying to figure out the correct part. On 2/16/17, I called Whirlpool again to find out if they had found the correct part. They told me that the new part had been sent to the service company and Whirlpool scheduled me an appointment right then for Monday, 2/20/17.So today is 2/20/17, the repairman came and went, Whirlpool once again failed, they lied because the repairman came out with the wrong part that was originally sent to him when he ordered the part back on 1/17/17. I called Whirlpool and asked for a manager. They connected me with the Resolution Specialist. I told her everything and pointed out that it has been six weeks without a refrigerator. She said she will take care of it and get the right part ordered. I asked her how long I should have to wait, cause at this point I have waited long enough. She said she will have an answer by the end of this week. I dont believe her, I feel as though Whirlpool is pacifying me. I dont understand why they cant order the correct part.I have no faith in Whirlpool that they will do the right thing or have any understanding on how inconvenienced they have made me. I have no faith to the point that I ordered another refrigerator from a different manufacturer. It will be here tomorrow between 8am-12pm. Oh, and Home Depot, they washed their hands of this a long time ago. And, I have yet to see the $50 Visa Card.

I bought my fridge in late 2008 and I am already experiencing potentially expensive repairs due to what I believe is a defective design system, of which, consumers are having to bare the consequences for those who collected our hard-earned cash and delivered a lousy product! I saw so many similar complaints about the ice system on this fridge that I am almost positive that it qualifies for a class action suit and settlement. How about a collaborative approach to this since we have all suffered needlessly? Tell me what you think and if you are in on it.

It took 5 deliveries to get a fridge that wasnt damaged. First two came from Leons - the same damage on both. Then they said we had to go through Whirlpool because so much time had lapsed. We had purchased the full set of Whirlpool Gold for our kitchen renovation; therefore, we were unable to unpack the fridge until the cabinets were completed. I phoned Whirlpool Canada, and they said they had to send a service tech. The service tech came, and he confirmed the damage and was told to patch it with a proxy. Sorry but I had just paid $1500 for a new fridge. I didnt want a dent and damage. We received no offer for discount to accept the damaged fridge. They sent another one, still damaged. They used their truck to deliver and the guy had no idea how smashed our brand-new trim.So Whirlpool sent another fridge, and even though I asked them to check it before sending, they didnt. It was damaged. This is four fridges. Im tired of fighting with Whirlpool. I called Leons, and they take care to get me a new fridge undamaged. I told Whirlpool about the damage, and they sent a form. First, they wanted me to claim on my house insurance. Why should I put on a claim? If not, get two quotes and fill out tons of paperwork. Im just too tired after fighting for over two months to get a fridge that isnt damaged. Not even an offer of compensation to cover all the time taken off work and the stress on me and my family. This is the second set of Whirlpool Gold we have purchased in the last 4 years. I doubt I will ever purchase again, because you are a company that doesnt treat your customers with respect or concern.

Whirlpool N50T91-403 purchased in Mar 12 had an error code 4. I knew the water heater had a safety installed in it when I was working on the plumbing and allowed it to drain the hot water side down to 16% of capacitance of 50 GL. After the plumbing issue was resolved, I saw the water heater had shut off (thermal protection) but the switch wasnt tripped as far as I could tell. Knowing small processors can only remember anything if they have power, I removed the Honeywell circuit board and with my multimeter probed all of the capacitors contacting them both (-) and (+) and in reverse order. Doing this forces the IC to forget its codes because they require a small amount of voltage to remember them, usually powered by a small capacitor. I reinstalled it and voila! Presto! It works again.

Let me start out by saying that I had a Whirlpool washer that lasted me for over 25 years and done a great job of washing my heavily soiled clothes. One day it refused to run and I tried to get parts for it but it had become obsolete and no parts were to be found for it, so I had to buy a new washer. I chose whirlpool again and let me say that it was a huge mistake. This model is a low water, high efficiency, top loading machine. It has nubs in the bottom that agitate to clean the clothes. The first time that I used the machine, I found that I had made a mistake purchasing this machine. It does not clean the clothes and there is NOTHING efficient about this machine. I have to run the washer twice to clean my clothes and they are still not clean. It leaves soap in the clothes and does not rinse them clean of the soap. What it does very well is extract water from the clothes during the spin cycle. This washer really turns up the high RPM`s on spin cycle. It has ripped apart several of my shirts during spin cycle. Whirlpool really failed badly on this machine. I see clearly now that Whirlpool is not the company that they used to be back in the 1980`s. I still have the whirlpool dryer that I bought back in the 1980`s and it still works very well. To end this story, I loaded up this NEW WASHER in the back of my truck and took it to the scrap yard and I asked them to destroy it in front of my eyes. I wished that I had recorded the destruction of this piece of JUNK and posted it on YouTube for the world to see. I got over $450.00 of pleasure watching the crane operator completely destroy this pile of crap. GREAT JOB WHIRLPOOL … YOU HAVE LOST A CUSTOMER FOREVER. I WILL NEVER BUY ANY OF YOUR PRODUCTS FOR THE REST OF MY LIFE and will advise others not to buy Whirlpool products as well. I am a male, 62 years old and work hard for my ill spent money on your JUNK. Life is always a trial, live and learn the hard way. Warning to all consumers. Do not buy Whirlpool products ever!!!! Whirlpool can K.M.A!!!!

I purchased and had professionals install a Whirlpool 30-gallon water heater in 2007. Since that time I have had issues with the unit not staying lite, but have been able to deal with it myself. Then in November 2011, it wouldnt work. After paying a plumber to come out and check everything, we got on the phone with Whirlpool who goes through their generic checklist, and after all that they agreed the control was no good. They sent a replacement part out at which time I had to pay to have put in. Now, March 2012, the same thing is going on with the unit. Customer service is their same polite self and have to go through their checklist, but unfortunately we were cut off. This was followed by calls and trying to get the same operator, who was supposed to call me back. It didnt happen. I then called and was hung up on. Finally, I had to work with another operator who again wanted to go through her checklist! She finally agreed the same control unit must be bad and is sending me a new one so I can pay to have it installed! They will not admit the unit is bad and replace it completely. I guess when buying Whirlpool you need to understand they dont back their products. It appears to be normal that a control unit from Whirlpool only has a life expectancy of 3 or 4 months. Last Whirlpool I ever buy!

This machine always leaves me questioning if its going to finish the cycle. It goes thru all kinds of spastic sounds in order to advance to the next step. I learned I cannot presoak a load more than 10 minutes before the machine empties ON ITS OWN! I just dont trust the machine and would not buy again.

After less than 3 years it was the bearings, of course. Then, being handy and not stupid enough to pay the $500 for the whole piece of crap Whirlpool/Maytag tub, we bought bearings from the PartsDr. We just didnt dig deep enough to know that the strators on these things are made out of the cheapest Chinese plastic and are cracked in the SAME TWO PLACES EVERYONE ELSES IS!!! Imagine that? Will scrub my clothes in a river on rocks before I ever buy a Whirlpool/Maytag Chinese again. All front load seem to have the same problems but at least some other companies admit it and are trying to correct it. Will research and as with everything else stay away from the USA/Chinese rusty, corroded junk.

We had the same thing happen. We purchased a brand new home and within 6mo the plastic around the handle started breaking off and pieces would fall into any food that was being cooked on the stove. Whirlpool fixed it for free but now the same thing is happening with the new door.

Strange bear like sound when it washes. We stopped it and on again, sound gone. Water on full water pump drain attitude ok. Big lid (grey) inside on. Ran some time water draining with tablets to make it clean and run better. Had someone to look for it, no sound. But when we now turned on, it sound like a mumbling high sound from inside machine or upper lid. We have some thermostat error a few times now. No hot water condition and no washing in high temperature. Håkon ** was the inspector of this strange thing happening. Could this be dangerous to let it run?

I had purchased a washing machine trough CSD canteen and go for AMC for five years on September 25, 2006. In September 2010, I lodged a complaint and the Engineer visited and asked for a replacement of the bottom cover. I said okay, but later on he told me that I have to replace the complete outer cover. I agreed and asked them to replace it. The cost is fixed for 2,500Rs. They replaced the cover but did not replace the bottom cover.I talked to the agency and they agreed to hold to 1,000Rs for the bottom cover and I paid to them 1,500Rs. Later they brought an old cover and I refused to replace that. They told that the bottom cover is not available. Then they never tried to replace the bottom cover. I arranged for the same from the local marketing for 600Rs and replaced it. I paid the service charge for the engineer.Later, I lodged a complaint that the machine was not drying the cloth. The engineer visited and told me that the belt will be replaced on payment. I agreed and he told me that I will visit the next day and replaced the belt. But he did not come until it was late.On September 18, 2011, with number DL0911018283, my machine was not switching on and I lodged a complaint to customer care. But no engineer visited me. Then I regularly complained but there was no response from the agency. On September 23, I talked to customer care, Mr. **, that I am going out of station and I lodged a complaint from the last five days that no engineer visited me. My AMC is expiring on September 25, 2011. I will come back on October and then send the engineer. On October 9, I reminded them that they refresh my complaint with number DL1011007031. The engineer visited and told me that the PCB of the machine is faulty and I have to pay 3,500Rs.I told him that I complained for this problem during the AMC period, hence they are supposed to repair my machine free of cost but he refused. I talked to customer care and tried to resolve the issue but I was not successful. Then I talked to Mr. **, the head of Customer care in Delhi, on October 12. He promised to resolve the issue but no engineer visited me and my machine is still defective. On October 13, I tried to contact Mr. ** several times but he or his PA is not picking up the phone. Now, how will I get to repair my machine?

Weve had our Whirlpool Cabrio washer and dryer just over a year. I like them both but then we are having problems with our lid. The first one cracked after 9 months and they replaced the lid. Two months later, the new one cracked and they replaced the hinges and lid again. I assure you we are very careful when lowering and lifting the lid. I do 80% and my husband does 20%, and we are very cautious of it especially after the second one broke. Now, I was just putting laundry in and the third one cracked while lifting the lid. There is obviously a problem, and Im wondering if anyone else is having the same issues. Eventually, it will crack all the way through which will cause the glass to pop up and the lid wont lock. I will not buy anything with a glass lid again!

I just purchased a brand new refrigerator from Whirpool and after 2 weeks been delivered I started having a lot of issues. They sent a technician twice to get it FIX but Im still having the same problem. And they dont want to replace the unit. They want to keep sending technicians to make the same repairs. Its a NIGHTMARE!! Please do yourself a big favor and buy a different brand. I dont recommend!! By the way this appliances are made in MEXICO!!

We bought the Cabrio washer and dryer on June 2008, and it wasnt very long after that, that we had to have a repair done. Then, it started twisting the clothes and the sheets into a big knot. Two king size sheets and 2 pillow cases got so twisted that they are no bigger than a watermelon, and believe me, they are very hard to untangle when they are soaking wet. The machine in the drying cycle sounds like a commercial jet taking off. We can hardly talk above the roar of that thing. I hate it with a passion. Whirlpool used to be all we bought, but that is going to change.Linda

I shouldve read the reviews online about Whirlpool before buying our washer and dryer Duet. 4 years later the main bearing is going out and its 1200 to fix it. No support from them or anything. They did offer a loyalty discount on a new washer... No thanks. Just would be another headache a few years down the road Im sure. Goodbye Whirlpool. Never buying anything from them or their other brands. Ill definitely spread the word too.

This is a good looking, inexpensive stove/oven. Stove top has four burners. I liked the split grates on the stove top. Its easier to remove and clean. I do not like the rubber seal on the oven door. I am used to the heavier duty seals on most oven doors.

Ive had it with Whirlpool products. I am now getting rid of my third Whirlpool microwave in just eight years. Every one of them had the same exact problem and Whirlpool continues to deny there is a manufacturing defect. Each of them developed a hairline crack extending through the bottom screw of the door handle to the glass on one side and the outside door frame on the other. They will do nothing about it and claim it is just a coincidence. No more Whirlpool ever!

I purchased this machine three years ago. It is junk. I have had two washing machines and they lasted for years and years. Never had a problem with either machine. I purchased them from Sears. When I the Cabrio, I was told it was the top of the line washer for Whirlpool. Three weeks ago it started making a noise like a plane taking off. It wouldnt spin the clothes. The repair person said that it could be three different things the parts, for which, would cost in the vicinity of $200. However, since it was making such a loud noise and water was coming out from underneath the washer, he was certain the transmission was out. He said the noise was an indicator the bearings were gone. I didnt see much point in repairing the washer if the transmission was out because it couldnt be fix.There was a couple at Lowes purchasing a machine at the same time as myself. They said they had a Cabrio also and it was only two years old. It wasnt spinning the clothes either and making a tremendously loud noise. They told us this before we mentioned that we had a Cabrio also. I will neither purchase another Whirlpool product. Junk!

Im 70 years old and always bought Whirlpool washing machines. My last one I bought at Lowes and it is the most Ive ever paid for a washer and its the worst Ive ever owned! Dont waste your money! Hard to get clothes balanced and it slams and bams like the old 1970 washing machines! Horrible!!!

I bought a WDT 720PADW2 dishwasher 15 months ago from Home Depot. In the last few months, it has begun to rust at the vent above the the handle. Whirlpool will not address the issue because it is out of the 12 month warranty period, yet is obviously a design flaw.

[Model WTW6300WW0, Type 580] A few years ago Whirlpool goofed - they left out the Perma-press cycle on a high-efficiency washing machine model.We noticed the absence of Perma-press (or Casual as it sometimes now called) on the shop floor, and were assured we could arrive at the same results with the dizzying array of buttons that allow the consumer to tailor the cycles to their wash load. It turns out that it doesnt allow this. Buttons are disabled on some of the cycles, thereby preventing recreating a Perma-press cycle. No amount of prodding... Whirlpool has provided me with an override for the combination of a normal wash and a gentle spin that comprise a typical Perma-press cycle.On contacting Whirlpool about the missing cycle, they claim consumers no longer want the Perma-press cycle. Puzzled by this statement, I returned to the showroom floor to see for myself. All the washers have Perma-press cycles. Whirlpool goofed with this model. They left it out. They have not provided a replacement machine for a consumer who blows this whistle on their goof. Among the solutions their customer support DID provide: add softeners to the rinse cycle and add dryer sheets to the dryer to reduce wrinkles [by purchasing a high-efficiency machine, we aimed to reduce waste, not increase it]. Among their invalid suggestions: choose the Casual cycle [there is no Casual cycle setting on this machine]; choose Normal cycle, then set spin speed to low [this machine disables the low speed choice on the Normal cycle]; on this machine the Perma-press cycle is renamed Delicate [Wrong. Delicate only swishes clothes back and forth, not robust enough for business shirt colors and cuffs]; on this machine the Perma-press cycle is renamed Colors [Wrong. Business shirts come out too wrinkled on Colors]. There has been nothing I can do to convince Whirlpool that they produced a lemon in this model [Model WTW6300WW0, Type 580] and should replace it with a normal washing machine. I have tried for years, only for Whirlpool to come to the same conclusion: its the consumers problem now, not theirs.

The technician that was here to repair my propane water heater called Whirlpool to get help with the problem. The pilot would not stay lit, they would not help him. I told him it was installed in a mobile home and he had to cap the gas to the heater, it was still under warranty. Later I found out there was a recall on this heater and that probably was the reason they told him that. I ordered a water heater just for mobiles and am in the process of getting it installed. I kept the old heater for now and will still pursue this issue under the warranty.

Two months ago, I bought a Whirlpool duet washer and the computer went out, two days after the warranty was up. It went bad that I disconnected the detergent mechanism, which made it work, for now.

Whirlpool side by side model WR5571CIDM. Unit rattles EVERY time refrigerator is opened or closed + plus every hour or so spontaneously. Rattle seems to come from the water filter area. Whirlpool serviceman says its normal for this model and calls to Whirlpool customer service say just live with it. Hard to believe Whirlpool considers this acceptable performance in a new model.

Sixteen months after I bought the Cabrio washer (model # WTW7800XWO), the F1 error light came on. I had to replace the electronic panel on the machine for $400. Whirlpool refused to replace it even though they have been replacing this panel for others. This is a common problem with the Cabrio washer.

This French Door refrigerator looked beautiful. There are only two of us in the home. We purchased it at the end of 2014 and it just keeps getting worse. The front of each shelving has cracked. They look like they are dried out plastic the way it cracks. The drawer tracks have seem to keep crumbling pieces off. This is not a cheap refrigerator by no means, this is the first time buying Whirlpool, and I believe the last time.

Very unreliable oven. Oven temperature never seems to get to the proper setting. Do not buy any Whirlpool appliance. They do not stand behind their product. A stove should be relatively simple but Whirlpool managed to produce a product that is complicated & unreliable.

I bought my home four years ago with a Whirlpool 50-gallon water heater in it. It was installed in December 2002. Well, my hot water went out. After being told I could go to Lowe’s because they would supply the part free of charge because there was a recall on the thermocouple unit. I went to Lowes. No luck there. They told me they didnt carry the whole replacement unit and I would need a number from Whirlpool. The guy at Lowes was very nice but said I was the fifth person to come in this week.I called Whirlpool and was told because I was not the homeowner that had purchased the item that there was no warranty on the product and that I would have to pay for the part. It cost $34.98 plus shipping, which was another $30.00 because I had it shipped overnight. Two days with no hot water was enough. Well, I got the part and hopefully there is nothing wrong with it as it was shipped in a box twice as big as needed with no packing what so ever.I just got off the phone with them again but this time spoke with a supervisor that told me there was no need for packing. There was no part of the entire assembly that could have been damaged. Will I ever buy anything with the Whirlpool name on it? Not only no, but ** no! Will I tell everyone I know about this? You bet. I am also going to write to Lowes and ask why they are continuing to sell inferior appliances such as these. I have to tell one realtor friend about this and just placed a call to another to tell him. The first had no idea that appliances that were marked still under warranty did in fact have no warranty at all if its a Whirlpool. I may write a letter to the editor of our local newspaper and hope that they will publish it to inform anyone reading the paper about these inferior products.

I purchased a Whirlpool range YGY399LXUQ in 2012 from a great local appliance store, Trail Appliances. In 2013 the control panel stopped working and I contacted Trail. They quickly came out and replaced the control panel. In 2014 the same issue came up, but Trail could and would not do anything so I contacted Whirlpool Directly - they came out and replaced the control panel. In 2015 (same month) the control panel is not working AGAIN and Whirlpool has washed their hands of it. A replacement is over $400 + installation. The stove is barely worth that much. I would have thought that they would stand behind their product, in that this is an obvious continual issue or at the very least the service that they provide. I would not recommend their ranges to anyone because they will not stand behind what they product nor will I ever purchase anything that Whirlpool makes as it is obviously low quality.

I purchased a Whirlpool cabrio mod. wtw5840bwo washing machine in Oct. of 2014. As of June 2015 I am ready to kick it to the curb. The washer works to it design and hasnt broke down but it doesnt clean our clothes. We load the machine, add the right amount of clothes and recommended detergents and 1hr later after the wash cycle is completed, the clothes still stink with the smell of daily perspiration. I went back to using our old washer that has a worn out agitator. It does a better job.

My house was built 20 years ago, with all Whirlpool appliances; built-in microwave over the electric oven, gas cooktop, and under counter dishwasher. The oven just gave out. Everything else works fine! Let me repeat that. I have a 20 yr old Whirlpool microwave that works just fine! Well, since the oven broke, we thought, maybe its time to update all the appliances. We went to the large appliance store from which our original ones came, and were told that all microwaves are now made in China by Sharp, and are crap!! Wed be lucky to get 3 years out of one. My jaw hit the ground. I couldnt believe the appliance salesman was telling us this! In fact, the appliance repairman that diagnosed my oven to be unrepairable ($100 trip charge, thank you very much) didnt have much good to say about the newer refrigerators... They contain much less Freon and dont seem to hold up as well... So, I guess Ill just keep my old appliances going as long as possible! How can appliance manufacturers stay in business!

We bought our Whirlpool Refrigerator a little over three years ago. Within a few months we started having problems with the unit. From ice maker issues, cooling and freezing. Initially the frig was covered under Whirlpools 1 year warranty. Then our extended 3 year warranty kicked in through HH Gregg which they supplied for free because of their poor handling of the initial sale. We have lost track in how many times a repair man has come out to work on the refrigerator. In the last year alone its been at least 8 times. The most recent problem had been the freezer not defrosting properly to the point where we had to store food in our neighbors freezer. The repairman has tried everything he knows and is stumped. Well our extended warranty has run out but theyll continue to work on the problem as long as we report the issue within 30 days which creates a whole different set of issues. The extended warranty states they will replace the refrigerator if it has the same problem 3 times. However what they dont tell you is that if you call BEFORE 3 time period its considered a recall and that doesnt count towards the 3 strike rule. We contacted Whirlpool and they wont cover the refrigerator because the repair company isnt on their approved list. Really a Sears repairman isnt approved? So buyer beware of a lemon Whirlpool Frig! They seem to have a way of not covering their product.

I purchased a new Whirlpool Cabrio washer 3 years ago. It is the worst washer I have ever owned. During the first year it had to be repaired. It continuously flashes F51 when I try to wash a load of towels or bedding. I am beyond fed up with this machine and will NEVER purchase another Whirlpool product. If you are considering purchasing one of these I would tell you not to waste your money.

6 years ago, we bought the refrigerator, the oven and the dishwasher. Theyre all Whirlpool appliances. With that, we took the 5 years guarantee extension for all those appliances. After 6 months, the electronic front panel of the oven jammed. The repairman knew what was the problem and had to change this panel. Then a month before the expiration of the guarantee extension, the refrigerator never stop running. I have to call them 3 times before they place a service call at the right place, very strange. Now, the auto-clean on the oven doesnt work. The very known E1-F5 error on the display and no solutions that work. Whirlpool, never again and I will make the real publicity for this brand without a shame.

We bought this fridge about 5 years ago, it was the exact same model as one we bought in 2003 but everything had changed, the plastic for the drawers was a fraction of the thickness in the older model and it breaks and cracks with the slightest bump like setting the lettuce in, the frame of the door is full of cracks and the fridge keeps leaking then freezing and making puddles on the floor. The little plastic tabs for the ice dispenser broke. It is absolute garbage. The one we bought in 2003 was great clearly the company has NO integrity or desire to make a decent product. I wont be buying anything Whirlpool EVER again.

Whirlpool stove, product ID WFG540HOES. I purchased a whirlpool gas stove in 2014 for a lake house. Came to my lake house to find the temperature was 90 degrees inside and the oven was running full blast. The oven had turned itself on. Whirlpool appears to be having a problem with this type of issue. Called their customer care department and was transferred to the appliance safety line which was only a line to leave a voicemail. Very bad customer service. My kitchen countertops and kitchen floor will need to be replaced, also cannot get rid of the burnt smell in my house. Do not recommend purchasing Whirlpool appliances.

We were at end of cooking salmon in CorningWare and the door blew open with amazing force!!! It is a double oven... Sounds like Whirlpool doesnt care so trust me we are not buying one ever again. :(

I have a Whirlpool top-loading washing machine model 3LA5580XSW3. The timer switch is not working and I have been told that spares are not available. Is this true? Everything else works well. Please advise as I really need a new timer.

After yet another frustrating round of laundry I have to write this. This has been the worst purchase (Cabrio 6800 Washer and Dryer) Ive ever made. Like other reviewers, I thought I was buying a high-end (high priced) product that has performed miserably from day one. Clothes do NOT come clean and for some reason, towels and dishcloths get ripped and shredded. All cycles (except sheets/towels) do not dispense enough water. Of course the one that does, results in the ripped and shredded problem. A little more than a year after purchase, we got an error code indicating the computer board was bad. Code would come up during initial cycle start and again at the start of the rinse cycle. Whirlpool basically said tough luck but shortly after, we started receiving offers in the mail to purchase an extended warranty for $175. Out of principle, I did not do this. Instead we discovered that we could push pause/start/pause/start multiple times and it would eventually keep going. We are still doing that on EVERY load of laundry (start and rinse cycles). I am not far from just biting the bullet and buying a new washer. It will not be a Whirlpool. One positive note is that the dryer has performed well, unlike some of the other reviewer experiences!

I bought a Whirlpool Duet Front Load Washer in 2008 and it began showing F71 and F70 error code in 2011. I paid approximately $1,000 for the machine. The washer wont finish the cycles and often wont start. When I press the power button, I hear the 3 beeps and after a while, shows the F71 error over and over. The information I gathered online indicates that many people have the same problem. The repair cost is at least $550 to replace the user interface circuit board and is no guarantee. This is ridiculous.How could GE sell consumers this kind of junk that fails to work only after 2 years. I had a top loader for 12 years with no problems, not a single repair call. My wife and I are extremely frustrated with piles of dirty clothes and no washer to clean them. I want GE to refund the cost of the washer on a 10-year prorated basis. This is only fair.

Best stainless steel built dishwasher we could find in this price range. Well built with lots of room and easy access to both drawers. Easy to clean filters and a nice modern look.

I bought a Whirlpool Cabrio washer and dryer on March 2010 from Leons under the dont pay for 18 months. It took 2 months for me to receive it. I thought it was a great washing machine. I made my last payment on July 2011.On the first week of August, the machine stopped working. The F 51 code appeared. I then looked up the code. I also looked up complaints. I called Whirlpool customer service and was told it would be $81.00 per hour for service plus parts. I asked why there are so many complaints about this machine, and after spending a good amount of money on what I believed was a good make of washing machine, I could not believe that they would expect a customer to then turn around and fork out that kind of money for repair.I was told that the one year warranty has expired, so it is my responsibility to pay. I am a widow with 2 children, working 7 days a week to pay my regular bills and now they expect me to pay for repairs on a washing machine that is only 15 months old. Thanks Whirlpool. I will be sure to tell everyone not to purchase Whirlpool products and thanks to my neighbors for letting me use their washing machine because I cant afford to fix mine.

Whirlpool Gold Convection Oven - I bought this new oven, cleaned it once. The bottom cracked where the spills had been. Since Id had it only two months, repair tried to say it was only cosmetic but had to replace it. Next time I cleaned the oven for multiple spills, (a year later) it cracked again, giving the bottom a shattered look where the spills were. I only cleaned it once and the bottom is ruined. I dont expect Whirlpool to stand behind this, but I agree these Convection Ovens require a Class Action Suit because they are selling faulty merchandise. Period.

New water making loud pinging noises when burner shut off. Whirlpool referred plumber. Plumber stated this is normal. After few months heater would make loud humming noise when burner turned on. Called Whirlpool again. Said I had to pay for plumber to troubleshoot and if part needed I had to pay labor to replace part. Would never recommend this product to anybody.

Purchased the Sears Oasis (made by Whirlpool) washer and dryer almost 4 years ago and I have worked on these machines more than the Maytag machine and dryer I used for over 22 years. Electronic and mechanical problems. One recurring problem is loose change working its way into the drain pump on the washer and it knocks a hole in the side of the housing. You later discover it when you go down to the basement and find about 50 gallons on water on the floor. Very poor design! Never happened the first time with the Maytag.

My brand new Whirlpool washing machine has been nothing but trouble from the day we first used it. We are now reaching out to try to contact the warranty department. Weve tried email and phone both and are having ZERO luck even getting a human to talk to about the problems. No response. Took forever to even find what we thought was accurate contact info. Lowes doesnt stand behind it. Now Whirlpool has a crap warranty department. We were warned and should have never bought it to start with. It is a total waste of money.

Very dependable. We loved all of our appliances in the past as well as in the present. It has been a go to for us especially with bad experiences with other brands like OG and GE. We have gotten a washer and a good dryer and have worked. No complaints whatsoever.

We bought the Cabrio less than 5 years ago. First of all, a high-efficiency washer should not require an extra rinse after each wash, but this one does. I cant see how thats being efficient. The washer, even for a small load, can take up to 54 minutes, and then when you tack on an extra rinse, its well over an hour, so what you may be saving in water, youre spending in electric and wait time. And then, there is still a soap/water scum left on the clothes, which is only evident on the darker clothing. Now, just recently, the washer is stopping, and NOT unlocking after about a minute into the start cycle. I will have to cancel the wash, turn it off and unplug it before I can get it opened. Im sure its something to do with the electric panel, which after reading the reviews, we are not going to fix, and we are headed out to buy the traditional top loader, NOT high efficiency, which I suspect will still be more efficient than the Cabrio.

I have been unhappy with my Whirlpool Cabrio washer since I purchased it from Lowes. I should have looked online before I bought it and then I would not have made the mistake of buying it. The washer leaves soap deposits on the clothes and sometimes leaves a colored soil. It has ruined numerous clothing by tearing out hems of towels and wash cloths and tore a hole in a favorite sweater. I prefer an agitator in my washer. From what I read, I will soon begin to have other major problems and then I will replace it, but not with a Whirlpool.

My washer is just two years old, and clangs all the time. I informed Whirlpool and they stated I should call a technician. Since the warranty expired, there was nothing they would do. It is just two years old. I researched others and this same washer has failed in less that two years. It is a very bad product. It doesnt wash clean and makes a lot of noise. If you send me your email, I can send you a video I recorded of it making the noise.

I purchased the front load washer 4 years ago and the board went bad in 2 years. It costs more to fix it than the washer is worth. Stupidly, I purchased the top loading Cabrio and it has gone downhill from there. Has always sounded like a jet taking off in the spin cycle. Then 18 months into the purchase, it started with grinding noises and load balance issues on the spin cycle. Seems like they have a lot of issues with these Cabrios. Spent a lot of money for nothing. I will never buy a Whirlpool again!!!

We purchased a Whirlpool Cabrio, top load washing machine WTW6600SW back in 11/07. Last week (todays date is 8/19/11), the machine sounded like a plane taking off when it spins out. When the local service technician came out this week, he said that the bearings are shot. Since the tub and bearings are all one part, we were told by the technician that the part and labor costs would be $379.99 to repair it. We originally paid $799.00 for the Cabrio, less than four years ago. Whirlpool would not even give us a concession of a new tub and bearing part as it was out of the 1 year warranty.

We bought the over-the-range Whirlpool microwave, model #WMH53520AH-1, about four years ago from Pacific Appliance Sales Kitchen and Home inside a Best Buy store in San Diego. The Magnetron and Diode have malfunctioned and been replaced. Now the plastic around the door is falling apart, cracking, and splitting. This is unacceptable, poor craftsmanship, and low quality for the price of this Whirlpool appliance. This needs to be reported to the company and properly addressed. Until then, were staying away from any Whirlpool related products. We also own Cabrio W/D. The washing machine has had problems from year one. Im submitting a separate review for this appliance. Consumer beware!

The control panel is difficult to use. It’s much too easy to switch power from the top oven to the bottom oven without knowing it. In addition, the plastic cover over the control panel makes it difficult to use especially if your fingers have flour or oil on them. It would be much easier and more accurate if knobs were used to control the all the functions instead of a electronic screen. Also, the clock has never operated accurately. Always runs fast. Temperature of the ovens is pretty accurate. However, it does take a long time to reach chosen temperature. Both ovens are large and able to handle an 18 inch round pizza dish. Other than the control panel, I’m pleased with both the gas stove top and both electric ovens.

Purchased a Cabrio large capacity washer. It NEVER seemed to get the clothes clean enough, and after the sensors and bearings went bad within three years (out of warranty of course) I gladly kicked it to the curb. I bought a Samsung that has been great. Id like to support USA made, but not when it is AWFUL.

Whirlpool Hot Water Tank Thermocouple - This is the third thermocouple we have had to replace on this hot water tank in the last six years. Granted the part isnt that expensive, but the service call and replacement have cost us dearly. This is faulty tank and Whirlpool needs to recall this tank and replace them with new tanks. The price of this original tank and replacing this thermocouple three times has cost us over $800.00 total. I am not sure angry is the right word to describe our dissatisfaction with Whirlpool.

Three years ago I bought a bottom freezer Whirlpool Gold refrigerator from Lowes. Two days after it was installed, I noticed a pool of water on the kitchen floor. This happened again. I called Lowes and they brought out another refrigerator, same make and model, and took the first one away. A year later the same thing happened. I had it repaired - quite an ordeal for the technician. He had to order a part and found it difficult to actually get into the freezer. Now after a year and a half approximately the same thing is happening. I cant afford to continue the repair bills and dont like the inconvenience (what if this happens when Im away from home?). The pool of water is substantial - its as though the defrost is simply emptying through the front of the freezer onto my floor.

Whirlpool Model WDT920SADM0 Dishwasher. We built a new modular home so Abraham Builders ordered all my kitchen appliances in 2014. We did not move in and start using the appliances until June, 2016. Here is what happened during the first 6 months: 1) Would not dissolve dry soap or packets as there were still particles and plastic in the dispenser. 2) Dishes were not getting clean and were spotty. 3) Would not dry dishes, ever!!! 4) Parts would keep popping off as we would find them on the bottom or hanging down. 5) Final straw was this morning around 4 a.m. (12/4/16)... woke up to the smell of wire burning in the house and discovered it was coming from the dishwasher that we had put on delay wash that night and when we opened the door, smoke came out from inside!!Since it was past purchase warranty date, we had no warranty and the builder would not return any of my calls on any problems and the manufacturer of my house closed the factory. Needless to say, we now have to spend another $900+ for another dishwasher! Not happy at all about this Whirlpool model and would not recommend it.

I am pleased with the steel tub, the ability to do an extra rinse and spin and especially the choices of water level that it determines by the size of the load. Its ability save water use. I would repurchase the top loader again. My clothes come out looking wonderful especially the whites and I do not use bleach. It does not get the mold or mildew odor that my last machine would get due to the rubber or plastic made tub. I love it.

I bought a Whirlpool water heater 5 years ago and after one year I had to replace the thermocouple every 3 months. Each time I call to complain, they would just send me a new thermocouple. I asked them several times to replace the item and they refused and just continued to send me replacement parts and refuse to honor their warranty. The water heater had some type of defect, but they still refuse to replace the item and did admit on the phone they have records of several parts that they sent.

GW399LXUS range is Dangerous. Sheet metal cuts your fingers. In over 6 months, Whirlpool has failed miserably in fixing the problem. Bad replacement parts. Incomplete parts shipments. A dozen service calls. The local independent service companies are the only ones who have acted professionally. Other than the poor people who answer the complaint lines, nobody at Whirlpool seems to care. The product is poorly made and the product support is not competent. The range may have the features that we wanted, but who needs all this headache?

We have the four-door model, french fridge part, drawer, and bottom freezer. Overall has been a good appliance. Icemaker burned out in third year. Icemaker replacement is very noisy, popping and groaning during drop-out and refill. Noise level otherwise is average.

When washing towels or a blanket or quilt, anything substantial it wont spin the water out of the laundry. This washer is only 5 months old.

We just wanted a black, good looking microwave, so far so good. It been easy to keep clean and cooks food fast. We actually installed it ourselves and it was pretty easy. It hasnt broken down or given us any struggles.

Twelve years ago we bought an LPG Whirlpool range for our new home in Rio Rancho, NM. About 5 years ago, a tenant at our home reported a gas leak and the propane company determined that the Whirlpool range was at fault. The dealer in Albuquerque repaired the leak, by replacing all the valves at a cost of $470. A week ago, after a propane fill, once again, at least one valve was found to be leaking. Apparently, Whirlpool does not know how to make a valve that holds up over time. Over a 7 year period, I paid almost double the cost of the stove, only having to replace it at 12 years. These stoves are DANGEROUS! I will not purchase another Whirlpool product for the rest of my life.

I called Whirlpool’s 800 customer service line to let them know I was having a problem with this loud humming and rattling noise coming from my refrigerator because of a manufacturing defect (according to the service tech that came to my house to fix it). Apparently, the metal grid is being held by a flat mental hook which vibrates. What a loud noise. We cannot eat in our kitchen: the noise it terrible. The repairmans solution was to put a piece of rubber between the two metal pieces. It worked until he left. I told him it would start again and it did! I even let the customer service rep hear the noise and she agreed. I am in the early stages of my problem, but from what I have read I am not very hopeful. I would like to have the names and phone numbers of the people at Whirlpool who refused to help. Maybe if we would all band together and call them, they would get tired of hearing from unhappy customers and fix the problems. I am game. Anyone else?

I bought a new Whirlpool electric range in the spring of 2008 and purchased the extended warranty from Leons. The oven worked fine for the first three & 1/2 years, but then the bottom element in the oven seemed to have stopped working. The top element would still come on, in an effort to keep the oven at temperature, but was not effective.I called in a repair. The technician showed up, turned the oven on, noted that the bottom element did not come on properly & replaced the motherboard in the control panel with no further diagnosis. The oven worked for approximately 9 months and then the problem recurred. I called in another warranty repair. This time when the technician showed up, he turned the oven on & told me he was going to order a new bottom element, which he installed about a week later, again, with no further diagnosis.Now, here we are again, one month off warranty and 6 mos since the last repair, and again, the bottom element in the oven is not working correctly. I reported the issue & my dissatisfaction to Whirlpool and was basically told, How sad, too bad - hardware components fail and theres nothing we are going to do about it. Seriously? This range is just barely 5 years old and has a history of repeated problems with the bake function - obviously, something is defective in this product.I can see it, if I had not had any problems until this point, but when the same issue keeps coming up & obviously has not been correctly diagnosed and repaired, I would think they would have enough integrity to offer some kind of help or solution. Given the history here, its highly unlikely that Im going to be willing to spend big bucks on another attempted repair that, in all likelihood, will be merely a short term band-aid, so Ill probably have to buy another new range - which I cant really afford right now. Trust me, it will not be a Whirlpool & it will not be from Leons.

WRX986SIHV00 - French Door Fridge, cost $3k. After 16 months lights on top of fridge and freezer broke, Whirlpool only states no more warranty and offers no help. For such a pricey appliance that is a very weak quality and inadequate service IMO.

I purchased my stove in June 2020. I had no idea it was to be connected to the internet, but no big deal. Had I known of all the other quirks I would have thought twice. 1: A red light comes on to tell you a burner is on but not which one. 2: A red light appears when a burner is hot but it doesnt show which one. 3: Only 3 burners out of 5 can be used for cooking the other 2 are warming and melting ONLY. 4: The stove updates its software whenever it feels like it and shuts off the oven and burners. 5: Periodically I have the oven on and it just turns itself off!6: The touch controls for the oven are in a bad spot because if you accidentally touch them when the oven is on the oven will shut off.Not sure if it has any serious problems just the inconveniences listed.

I purchased a water heater Model # UG1H50400TBN, Serial # 0913T400920, from Lowes in Corona, CA. 05/07/2009 for $528 plus tax. I have replaced the following parts: 02/10/2010 Thermostat Valve, 07/23/2010 Thermostat Valve (2nd time), 08/10/2010 Burner assembly, 02/10/2011 Thermocouple, 02/17/2011 Thermostat Valve (3rd time), 12/17/2014 Thermocouple (2nd time) and 03/20/2015 Burner assembly (2nd time).Today I called WHIRLPOOL Customer service (877) 817-6750 because my water heater water is warm. I told the tech support agent that the pilot light was on so we agreed that it was the thermostat valve AGAIN. He wanted $30 for overnight delivery and I refused to pay. Now I have to go out and buy this part because Whirlpool like the Banks is too big to fail and they have license to RIP-OFF the consumer without penalties. Whirlpool has all of information and they can verify everything I wrote here just by the serial number.

I purchase the front load, energy efficient brands, low water usage. Love Whirlpool; never had a problem with their appliances. Front load, low water usage, clothes dont sit and spin in dirty water. Dryer has multiple cycles. Perfect for the whole family. My last Whirlpool set last me over ten years, wanted that same quality level in my new purchase. I wanted a quality machine. I was very familiar with the Whirlpool brand and knew that was going to be my first choice in a brand. These were full size. The tub is large enough to hold a king size comforter and wash it without destroying it. The dryer has a separate attachment for pillows and shoes (sneaker plus) and was competitively priced at the time of purchase.

I am concerned that Whirlpool microwaves installed over the stove have extremely faulty doors. I have two homes in which I have Whirlpool microwaves, and both have huge cracks in the door and small pieces inside the doors beginning to fall out. It deeply concerns me that it will cost more to replace the doors than to replace the microwaves. I have always believed in Whirlpool appliances but now feel that I will have to change brands. My question is “What in the world is wrong with your doors that they crack so easily and the company holds no responsibility with such faulty work?” I would simply think that this was just a faulty door on my microwave, but I have two that are cracked! This definitely means you have a faulty product.

The American Standard 95% 2 stage variable furnace is by far my favorite furnace to install. I know exactly what to expect from this furnace and I have had zero factory issues with this model. Outside of making a few sheet metal transitions this American Standard standard 95% furnace was very easy to install as well. And like the 2 stage variable … no factory issues.

My last fridge leaked all over the floor. Mice were living in it also roaches. My landlord didnt believe me though Ive shown him several times. He didnt want to spend the money. Luckily his wife came over and saw how bad it was so she got a new refrigerator for me and it has been a blessing ever since. It is just the right size for my apartment.

We purchased the Whirlpool Cabrio washing machine around January 2006, and from the start weve had nothing but problems with this appliance. Within the first year, water was leaking under the washer which was coming from a crack in the plastic housing of the water pump. I replaced the pump myself to save on labor. No big deal. The very next year, I started getting the F51 code and there was no way for me to get around calling a service company to have it repaired. $350 and one circuit board later, it was repaired. It remained working without fail until recently when it began giving the same F51 code. Let me guess, another $350 for better repair? I have to assume that the new circuit board that was installed wasnt any better than the original one that was replaced. I wouldnt put another $1 into this hunk of junk and Whirlpool should be ashamed to have this product on the market. I will never buy another Whirlpool product.

Such an expensive refrigerator but poor quality. Bought at Home Depot back in November of 2019. The bottom Freezer freezes up messing up everything only three months after purchase. I wouldn’t recommend it at all to anyone.

I have a 4.5year old Cabrio washer. Ive replaced the water pump 3 times due to a weak plastic part which keeps blowing out due to pressure. Now, the unit is leaking rusty, black fluid from the bottom. I purchased it at HH Gregg in Indianapolis, In. Svs tech called. They have never seen this on such a new unit. Parts and labor will equal $400.00. Calling whirlpool customer care did nothing. I offered to pay the labor of $100, If they would be willing to pay for parts. Talked to a supervisor who offered to sell me an extended warranty costing $300.00. I am a stock owner in Whirlpool, no joy, dissatisfied with faulty product. They are unwilling to make this situation right. The unit is poorly made. I think a $800 unit should last longer than 4-5 years. In 2006, Whirlpool stopped offering a 5 year normal warranty on their units. Supervisor would not let me talk to anyone else.

Warning: Whirlpool water heaters are junk! Spent $553.00 for a high quality ( lmao ) water heater that had a 6 year warranty. Started leaking internally and rusted through, then rusted a hole in the bottom. 6 years and 3 months later they said you are S.O.L. Leak occurred well over 3 months ago, but they said it has to be reported before the 6 years. Do not waist your money on this junk!

I have the top load Whirlpool. Its very roomy for my covers, rugs & towels. It has a setting for me to just clean my washer or if I need to just rinse it. It has a cycle just for that. Or if I need a quick wash or a just cold water wash it has those cycle. When my cycles are done it makes a cute jingle sound to let me know its done.

I purchased a Whirlpool 3-door refrigerator with the freezer on the bottom on 8/17/12. Within 4 days, the ice maker stopped working. It took two days for the repairman to come out and fix it. So all is well with that. Less than 2 weeks later, the refrigerator isnt cooling. Several days later, the repairman came and determined it was the evaporator fan motor and clutch. The parts were back-ordered for 10 days. Parts came in 2 more days before he can come out and install them. He realized they sent the wrong parts. Another week went by, then he came and replaced the fan motor, which is now making an ear-piercing buzzing sound. He came back a week later and said it needed a gasket, which is back-ordered. In the meantime, he put some stick on insulation around the unit. Not much help. Another week went by, and the gasket showed up. It is still making a high-pitched whining sound. He said it was the compressor. Whatever! I hate the refrigerator. The sound is one that just grates on your nerves and you can hear it in all the rooms surrounding the kitchen! A repairman has to deem it unrepairable before they will even consider replacing it. They consider it fixed. What about my bleeding ears! I just want it gone! I am so disappointed. I thought Whirlpool was a good product with a solid reputation. I have a $2300 noise maker! Is there a class action lawsuit?!

Our Whirlpool refrigerator had to have repair in less than a year after purchase. That was a bad experience last summer and I had to complain through every avenue I could find just to get the replacement part shipped to the repair shop. Now I know it was not too smart on my part, but I bought a Whirlpool washer last September. You guessed it, not even a year old and it is not working. All I am hoping for in this posting is to help some other hardworking consumer make a better choice with their money. It is probably not advisable to buy Whirlpool.

Sometimes, it doesnt get the dishes clean. I am not sure if it is the dishwasher or the detergent. I recently switched to Finish Quantum Max and it seems to be doing better. I always use the pots and pans cycle. Lots of features, most never used. For instance, china crystal, quick wash, rinse only. The size is ample but the interior design could be better. Solid black, looks good, Model GU1500XTL82.

Whirlpool side by side. When the compressor cycles, there is a loud knocking noise. Called Whirlpool when under warranty with no results. They could not tell me the cause of the knocking. Sort of live with it attitude. The funny part is when we have someone visiting and the knocking starts, they are puzzled as to why we are not answering the door. Sounds like someone knocking on the front door. We have been whirlpool customers for 30 years. Probably will not be so in the future. Too bad that a great company has go the way of the Nash and Studebaker automobile.

When you shell out the money for a new water heater you expect it to work the first time. Mine did not. Luke warm water was all that we could achieve. After going through the troubleshooting steps we could not clearly define the problem. So they ordered me the parts and sent them to me. The parts were for the old model control unit and does not mate up with the wiring that is in the unit. The representative was put back in that they had no idea how that happened. And, no wrench came with the thermostat just another thing to spend money on. I told them I have had it. Then they say that this is a manufacturers defect and they can provide me with a list of repair technicians in the area. I gave them one star because I could not give them zero. They should have lead off with the service technician. Still not repaired. I will keep you updated.

Purchased a Whirlpool washer/dryer pair @ least 5 years ago. Great machines. Washer washes very clean. My only beef is that once the cycle starts I cannot open the lid. Dryer will dry almost anything in 10 minutes or less.

We bought an oven built in from IKEA - Whirlpool. It didnt work from the beginning. We called for a technician, who comes in the next day, took the defective part and ordered a new one. Took two weeks to arrive. Now I just found out that I will have to wait another week for somebody to come and install the replaced part. I am very disappointed with their way to serve me as a client. I explained to them that itd be nice if the technician it will come at the first hour in the morning ex. 9 am so I can go back to work after that. Which is not possible. The tech is more important than you as a customer. The technician will give you a 2 hours windows to arrive and after that who knows how long it will take the repair. So far I have this build-in-oven in the kitchen just for design, is not useful I doubt that it will be working soon. The lady who called me from Whirlpool Canada was giving me theyre the option in the manner or take or leave it.To be honest, I regret buying this oven, so far I havent used. Wasted my time trying to get them to be more efficient, but got the message from them that I dont matter. Never been treated so wrong by somebody who is working in customer service. The first call it was coming from a company which is located in Maple Ridge, BC phone number 604-466-5597 and when I insisted on having the repair being done asap they hung up on me. I asked for supervisor or a manager, and they told me they are not allowed to give any of those on the phone... Buying this oven was a mistake, trying to deal with them another mistake. I dont recommend to anybody this oven or dealing with Whirlpool Canada.

Whirlpool Wash-And-Go washer and dryer - I purchased these new November 2016. Since week two, they have been a constant problem (i.e. not enough water to even get clothes wet, forget about clean; gulping soap from the dispenser; rubbing holes in clothing; putting rust on washed items). The dryer NEVER gets the clothes dry; no matter what setting they always come out damp, even after Ive put them through for two cycles.Three separate repairmen have come to work on the washer replacing sensors and the entire control board. It worked fine for two weeks, now its back to guzzling soap. (It is supposed to do up to 12 loads on one refill of detergent. I get two per refill. Ridiculous! Soap isnt cheap!) And, today it ruined brand new bathroom mats with rust all over them that I had to hand wash to try and remove without much success. At this point I would advise anyone looking for new appliances to try any other major brand and NOT Whirlpool. As soon as I can get the money, these are being junked and Im NEVER buying Whirlpool anything again!

We purchased an electric range model WFE371LVQ O in June 2010. This range is only used during the winter months in our vacation home. In January 2016 the oven turned on by itself. The control panel was replace. It happened again on 1/25/19. IT IS A FIRE HAZARD!! Thankfully we were home both times. The only way we got it to turn off was to flip the circuit breaker. If this would have happened when we werent home and a fire started and it killed our dogs I have no idea what I would do. Im not even attempting to have the control panel replaced again. Well be buying another brand. I DO NOT RECOMMEND THIS TO ANYONE. The company must have known about the issue because when we called the first time it happened, which was several years PAST the warranty period, they didnt hesitate to do the repair free of charge.

The Whirlpool Gold Series we purchased, to replace the older refrigerator, has far exceeded our expectations. The French Door setup was exactly what my wife had talked about. The saleslady at Home Depot, where it was the least expensive by $283, was very well informed. We went through the specs, colors, types of finishes, etc and picked the perfect one for my wife's needs and wants. The model performs well fully loaded or almost empty. She told a few family members and they went out and bought the same model, or next model up, as we did. To wrap it all up, "Buy this. It performs as well as, if not better, than all the rest."

To Whirlpool Headquarters, Our message to those whom wish to listen is that your product is only as good as the service company you employ to handle service and repairs. Our most recent experience with A&E Factory Service has us convinced we will never buy Whirlpool appliances again. After a two week wait for our scheduled appointment we were dealt a most unprofessional diagnosis as to what may be the problem and then told that to service our appliance would result in overtime and that simply wouldnt be happening at this visit. The appointment time was 12 to 4 PM the repairmen was here at 2:30 pm only for five minutes. We have spoken with a Michael ** with your company who advised us to wait for a call from A&E which no call was ever received. We will be sharing our disgust with Home Depot where we purchased our refrigerator and alerting them to avoid further customer dissatisfaction by no longer promoting Whirlpool in our area. We are level headed and fair people just not able to grasp that a company as big as yours cant do better than this.

I purchased a Whirlpool Cabrio washer in July of 2013. In the first 6 months had a technician in to repair it. Worked fine up until now. The washer fills up, the clothes just soaks there for awhile (doesnt wash) then drains out. It doesnt fully drain so I have to put it on spin and drain again. Any suggestions on what I should do?

We purchased a KitchenAid KFIS29PBMS00 in August of 2013. By March of 2014 it had stopped freezing and producing ice. Sent out a technician (mind you each technician has to come twice, once to diagnose and then to repair). They determined that all of the panels and ice maker needed replaced. Did so with no resolution. Placed another call. This technician determined that the compressor was bad. Installed a new one on April 10th. The fridge worked for 30 days. Stopped freezing and producing ice. Placed the 3rd service call. Was told that the new compressor was bad. Technician showed up on June 5th to replace it but did not have one with him. He was told by Whirlpool that they had discovered a wiring problem and that if the Serial number begins with K322 -K335 yours is one of them. We are K324. He ran a serious tests and contacted Whirlpool. I was told it is not in Whirpools hands. LUCKY ME NOT. It is now June 19th, I have made 2 additional calls to KitchenAid after not hearing anything back was told that I was in the process of receiving a new fridge and that I would get a phone call. After nothing I called back again. After 47 minutes I was transferred to a Supervisor. According to her while we were on the phone, she ordered a new refrigerator. No upgrade, compensation or a care in the world for the consumer. I will NEVER purchase a Whirlpool appliance again. I expect to have to call back again.

We bought the Whirlpool top loader washer and the drum broke down and after several attempted fixes it was replaced by new one as we were being financed through a business. So here comes the new one - same exact washer. Not only did it not clean well (normal soiling) then it goes to ul which means not balanced... not because clothes arent but because the thing that balances - it went only after a yr!! It would also keep filling draining again to no drain leaving clothes SOPPING wet... So very disappointed to say the least. What a piece of junk this washer is!! Its going to the curb tonight and being replaced by GE - NO MORE WHIRLPOOL AGAIN !!

Yesterday I purchased this Whirlpool top load washer model WTW4816FW with agitator and we installed it at our vacation home and I started a small load to wash. Yikes, it made noises like a machine that is on its last legs. I knew from washing clothes for 40 years that this is NOT right. We, hubby and I waited and listened to this piece of junk to finish the cycle. Thank god I had set it for a short wash. We also videoed this contraption while it was grinding. I called Lowes and politely told them I was returning it. Thankfully they never had a problem with us bringing it back. (This must happen often.) I go back to the appliance department and decide on a Maytag. I noticed that it looked like the junk we just returned. I stood there and looked up the model number online and lo and behold there was a video of it doing exactly the same noise. It was virtually the same machine I just returned with just a name change. Needless to say we left the store washerless until I can research this further. I then found out that Whirlpool now owns Maytag. Thing is I just bought a front loader Maytag for my main home and it works good. It was a replacement for a Whirlpool without a agitator which worked well too. The YouTube videos seem to be washers with agitators doing this. I just wish I could post the video for all to hear. I guess we are all at the mercy of big companies who dont care if they make a good product as long as they can make it cheap.

A couple years ago we purchased a Whirlpool Cabrio WTW8000 top-load, high-capacity, washing machine based upon good claims of the salesman at Lowes - Appliance Dept. This was not an inexpensive machine. However, this washing machine failed to live up to representations and performance is poor. However, biggest complaint is that clothes are able to get stuck between drum and the unique agitating device which results in holes and tears in material. This is a significant design flaw and were not sure why more people dont complain about this rather significant design flaw. Of course, there are other shortcomings... but destruction of clothes is a serious problem. While this machine is in excellent condition, it will be replaced with a more traditional washing machine with vertical agitator ASAP.

After only 3 years using my Whirlpool front loading washing machine the inner tub is already broken. The repairman said the cost is just about the same as getting a new washer. After reading all the horrible reviews on the Whirlpool washer I WILL NOT be getting a Whirlpool. I am so disappointed in the washer and do not recommend it to anybody. Do not buy a Whirlpool appliance ever.

Less than 2 years after we purchased our whirlpool dishwasher, the rack started to rust. Now the tines are so soft they fall off. The last time we bought a dishwasher the Same thing happened, but after 15 years! They dont even have an option for that to be under warranty so it tells me they dont stand by their product. I will never buy whirlpool again.

Our Whirlpool Duet Washer started sounding like a jet engine 13 months after purchase. We spent $800 on a washer and it started to get very loud during spin cycle. After reading several reviews online with other people describing the same problem, figured it was the bearings. $800 to do my laundry for 13 months kind of crazy right. It would have cost almost $300 for the extended warranty through Whirlpool. In order to have it repaired, the cost would be around $600 because the drum and bearings need to be replaced at this point. Whirlpool’s customer service was no help and pretended they had never heard of this problem. However, reading reviews online tells me otherwise. I can buy a new Samsung on sale for $623, so that is the route we will probably take. We feel extremely cheated by what was once a well-known, reputable company. We will not buy Whirlpool/Maytag again until they put more emphasis on quality products with a cost efficient, longer duration warranty plan.