Its a very good one, it kept my stuff cold, and fresh when my other fridge went on the Fritz, but only one problem, and that is, it has glass shelves and if you have kids, it’s hard to keep clean!

18 months ago my husband and I bought our first Whirlpool washer and dryer to go with our first home. 6 months and the dryer stopped spinning. There was an issue with the belt. 12 months later the washer has stopped draining and spinning. It is 2 months since our first filed complaint with our extended warranty company and we still dont have a washer that works. I dont care if I have to take my laundry to the river and beat it with a rock. I will never buy whirlpool again.

Bought the Whirlpool Duet washing machine. It lasted around eight years. In the meantime I was replacing the rubber door seal cleaning out the pump constantly. The plastic pieces inside the drum all broke. Every few months I would get an error code. And During spin cycle it would literally shake my entire house. The problem with all the front loaders is the construction of the drum and the drum bracket. They are made of dissimilar materials. (Stainless and zinc) When you add soap to the water then the bracket becomes an anode and the drum becomes a cathode, which creates electrolysis which corrodes the bracket. When the bracket breaks your machine is totaled. I’m finished with every manufacture except Speed Queen. I bought a Top loader Speed Queen and I love it, it is built like a tank.

I recently purchased a Whirlpool refrigerator, model number WRT351SFYB00. Several months later, I noticed a small amount of water on my kitchen floor. I moved the refrigerator and found the hard wood floor under it had been completely ruined, so the leak had obviously been going on for a long time. Possibly since day one. I called a repair man. He identified the leak was coming from a cracked drip tray which was not uncommon. However, much to his surprise, due to the design of this model, he was unable to remove and replace the tray. He explained there was a metal panel bolted in place that was preventing him from replacing it. He said this panel was also bolted to the compressor. Therefore, the best he could do was caulk whatever cracks he found in the existing tray and hope for the best. It goes without saying he could not guarantee his work like he normally does.I noticed this same complaint on a user forum website on Appliancepartspros.com, so this refrigerator obviously has a significant design flaw. My repairman said if it was his refrigerator, hed get rid of it, and also indicated that after seeing this, hed never again recommend Whirlpool to anyone. All I know is that Whirlpool is permanently off of my list now as well.

After one of the door shelves in our new refrigerator cracked, I ordered a new shelf from our local agent Neuman Appliance repair in Ashmore, in July of this year (2014). I was told that it would take a while as Whirlpool were notorious for poor service; however, it is now the middle of September, and we are still waiting!When we ordered a new part for our dishwasher from Fisher and Paykel, we received the part in just 3 days. I mention this to give an idea of what good service should be.

There are plenty of reviews on this board already about how the so called AquaLift technology for oven cleaning is completely worthless so I wont repeat what they have already so eloquently described. AquaLift has managed to take us back in time to around 1947 or whenever it was before the old easy off oven cleaner was invented. I purchased the cleaning kit (affinity) as well but it doesnt do much of anything. The only people who might consider purchasing a stove with AquaLift are those who do no roasting or broiling of meat. The oven looks beautiful, so maybe it could be for those who enjoy a show kitchen and prefer takeout.

My wife and I purchased the Whirlpool French Door Bottom Mount Refrigerator in April 2013. Thank God we purchased the extended warranty. In June 2014 the ice maker quit working and delivering water. We have had the service contractor that WHIRLPOOL has qualified for all repairs. They have set up FIVE appointments to resolve the issue, all of which I had to leave work to meet because they do not provide any scheduled service outside the hours of 8am to 4pm. The first time they came the service man told me that WHIRLPOOL RECOGNIZES THERE IS A DESIGN FLAW BECAUSE THESE ARE NOTORIOUS FOR FREEZING UP AND NOT WORKING. I asked the repair man if there has been a recall because of this, he said no because WHIRLPOOL WILL JUST REPAIR THE ONES PEOPLE COMPLAIN ABOUT! I called Whirlpool headquarters today. The advisor said he will register my complaint. I asked, Is that it? What does that mean? He said, I cant tell you what happens after I register the complaint. I WILL NEVER PURCHASE ANOTHER WHIRLPOOL PRODUCT. I hope this may help someone NOT make the same mistake. If you need to talk to someone in upper level management to discuss your issue, forget it...they want the position but no accountability.

Purchased a Whirlpool French door in April 2020 during the pandemic for 2K. The first week of owning it my fresh vegetables froze. I lowered the factory set temperature by one degree. The next week the ice maker stopped making ice. 3 days later it started up again. The 3rd week my freezer food defrosted and the ice maker stopped making ice. Called Whirlpool And requested a refund. They said, No we will send a tech. The tech determined the control board was defective. I had to empty the entire fridge and turn it off, defrost it for 24 hours. The headache to find someone to take your food! The part took 2 weeks to get replaced.The tech said, If this doesn’t work we will have to come back and take the back off to see what the issue is. Told to defrost again for 24 hrs. The ice was so thick we did it for 48 Hrs. 1 week later ice started to form in the freezer and the ice stopped working again. Called whirlpool demanded a refund and they said no. A tech will come again. I’ve relocated my food 3x already. How many more times can I do that! Whirlpool is not concerned about their reputation at all, as I read through other reviews of situations similar to mine. Do not buy whirlpool!

Whirlpool refrigerator Model #GX5FHDXVY010, freezer on bottom. Ice maker broke within six months of purchase. Made loud noises, would not function to freeze ice. Turned waterline off and now use ice trays like the old days. Shortly thereafter, second unrelated problem started. Drain line started backing up and runs into the bottom of the freezer floor where it freezes into a thin sheet of ice, and then runs onto the kitchen floor. Have had the line cleaned out over and over again. Have been buying fridges for 50 yrs. and have never had this problem. Whirlpool says call a repairman and pay to have it fixed, but it happens over and over again. Whirlpool should come up with a permanent fix and pay to have it fixed. Based on the numerous complaints of this problem, this model needs a recall now.

French Door model WRF989SEAE01 - Fridge runs very loud after 3 weeks. Ice build up inside of fridge - back left. After numerous repairs, dealer replaced unit with new. Three weeks, loud noise again. After 7 months, the ice maker has quit, the freezer is thawing items, the fridge part is not cold enough (all settings have been boosted). Now Im concerned it is going to completely fail or burn our new house down. All new Whirlpool appliances in new home and this thing is proving to be extremely unreliable. Dealer is now out of loop (gave up) and told us to deal directly with Whirlpool. After 2 units and same issues, it has to be a design flaw.Can anyone start to move on a class action lawsuit or do I wait until it blows up or burns down the house? We are of retirement age, no kids, and our appliances have had NO ABUSE. Another acquaintance has same fridge about 2 years old and it has completely quit.

Pros: The refrigerator is large and roomy, easily adjustable glass shelving, and easy temperature controls for the refrigerator temperature and freezer temperature. Cons: the refrigerator is bulky and limits space in a small kitchen. The lower freezer door does not seal very well and requires frequent tweaking and adjusting around the door seal. Also, the freezer handle becomes loose easily and requires tightening fairly often -- which is a pain to get on the floor on your back (and a flashlight plus a special wrench) to tighten the handle.

Everything I buy from this company breaks all the time. I purchased these brands hoping they were good but apparently not. Always have to get them serviced. Lately they did an exchange on my fridge. Hope it helps because after thousands of dollars of food in the garbage it better work. And the washer thought, Oh Im paying more. It will be good. At this point will cost me less to buy from another company. Buyers beware. Cause the company cant do nothing good for me so dont buy from them.

The washer never uses enough water ever. The clothes are not clean and it sucks! The clothes are half dry when agitation is going. The bulky setting doesnt clean the clothes either. Ive tried every detergent on the market to see if it would help. No different results. I paid a lot of money in 2015 for this washer and Ive had bad experiences ever since. No change in my water bill since I have to usually wash clothes and towels twice. I want my money back so I can buy a better washer! Im beyond aggravated! I have looked for my receipt but its been awhile. I did get insurance on it. I bought it at Lowes it should be on my card they scan.

We saw water all over my wood floor and traced it to the lower freezer unit of my 15-month old refrigerator/freezer. We had to call a repairman which traced the problem to a frozen defrost. He put in a new thermometer at the tune of $200 and now we have to deal with a wood floor problem on top of it. I purchased because Whirlpool was always known to be a quality product. I wont make that mistake again.

I purchased Whirlpool washer in 12/2011. Immediately, I noticed the noise and called service. It was a whistling noise. The clerk told me nothing was in the manual and it would cost $65 to have a tech come out. He advised me to wait until it was louder and more consistent. I called again when it was. Gear case was replaced on 5/2/2012 five months after purchasing the machine. I called Whirlpool again in 5/2013 - same problem. I was told the diagnostic call would be $95, labor which is extended for a major job is $85 and the part would be $290. It would cost $470 to repair as the gear case was guaranteed for only three months. This machine is a lemon since the gear case is now shot again prior to the machine being 1-1/2 yrs. old. I called Whirlpool and spoke to Amy (Esc. Sup.) who advised they would replace the part only. The appointment was scheduled; the tech came, did diagnostics reading a manual and said the gear case is shot. I inquired, Well, you are going to fix it today right? The reply was, Oh no, it has to be ordered and its a two-man job. When I arranged for this appointment, this was clearly explained and what I was expecting, two men and the part to be replaced with them. Now its a five-day wait to get the part and then a scheduling issue when they could do it. This machine is a lemon and Id like to have the machine replaced or my money refunded. This is a runaround, scheduling the appointment and having someone show up with the manual and having no parts and not knowing that it was the part which broke again from previously being replaced.

I bought a Whirlpool refrigerator side by-side model #ED2PHEXMQ00, made in 01/04. As I was letting my dog out at 4 am, I heard a sizzling noise and I immediately smelled an electrical burning odor. I lost all of my food, but thankfully I caught it before it caused a fire. Had this happened during the day, I would have lost my 3 dogs and my home. I had to borrow a mini fridge for the time being because I dont have the money for the repairs or replacement. Since this is an ongoing problem, Im not sure replacing the part will make me feel confident in trusting that it wont happen again. I may not be as lucky to be standing next to it if it does happen again. Whether its under warranty or not, Whirlpool should take responsibility and issue a recall and replace the parts. I would never suggest buying a Whirlpool product in the future.

I am extremely disappointed in my new Whirlpool washer dryer matched set. My washer started to leak at less than 6 months of age, and my clothes are extremely wrinkled due to excessive spin and smell absolutely foul. I have adjusted the spin cycle to the lowest setting to prevent wrinkling as suggested in the product materials. I have cleaned the washer with the recommended product on the clean washer setting, although now with the leak, that means a good floor mopping too!I have contacted customer service about the leak since the machine is still under warranty - and they gave me a 4-hour window on a specified day for the service. I took the time off work and the technician failed to show. I called twice to follow up on his whereabouts and ETA. They did nothing except tell me to keep waiting. 45 minutes after the outside hour of arrival had passed, I called again. The customer service offered to make me another appointment so I could take another half day off work and hope he would show up the next time. When I asked for a preferential booking (with a real time) to minimize taking more time off work, the manager said all she could do was give me another 4-hour window. I said that was really bad service and she hung up on me! Another rep did do a little better - he sent me a name and number and said I could try to book an appointment directly and hopefully minimize the additional time off. Its the last Whirlpool appliance Ill buy - with that kind of customer service, Id rather be out pounding my laundry on a rock.

My mother-in-law purchased a Whirlpool refrigerator in 7/2010. It broke down the first time in August then consistently after that. We have had repair people out multiple times and the issue continues. I called Whirlpool and they said since it was purchased more than a year ago, it is not their problem. You would think that in all that time they would have found a way to repair or replace it. To make matters worse, we have had to call hospice in to care for my mother-in-law, all she wants is to get ice and water out of the door.

Greetings: I purchased a Whirlpool refrigerator on July 3, 2014. And the supports for the door to open and closed have grinded and worn out - not allowing the door to close properly, requiring being lifted up, and pushed close as much as possible. Not the quality I expected with the purchase of a Whirlpool product. I want this door repaired or replaced at the expense of Whirlpool. Having paid over $600.00 for the product, I didnt expect no problems like this at all, poor design. The weight of the door is too heavy to support a hinge mount in plastic, its ridiculous. Now cooling is being wasted, runs constantly, and just not the quality I expected nor received.

I purchased a Whirlpool cabrio mod. wtw5840bwo washing machine in Oct. of 2014. As of June 2015 I am ready to kick it to the curb. The washer works to it design and hasnt broke down but it doesnt clean our clothes. We load the machine, add the right amount of clothes and recommended detergents and 1hr later after the wash cycle is completed, the clothes still stink with the smell of daily perspiration. I went back to using our old washer that has a worn out agitator. It does a better job.

I bought my fridge in late 2008 and I am already experiencing potentially expensive repairs due to what I believe is a defective design system, of which, consumers are having to bare the consequences for those who collected our hard-earned cash and delivered a lousy product! I saw so many similar complaints about the ice system on this fridge that I am almost positive that it qualifies for a class action suit and settlement. How about a collaborative approach to this since we have all suffered needlessly? Tell me what you think and if you are in on it.

The self cleaning work very well. All you need is clean the filter every time you use the dryer. I had the large capacity. I can wash my blankets and heavy clothes like commercial machine and the machine is programmable for your wash load.

I bought a washer dryer Cabrio set and the washer after 2 years has a bearing failure and is squealing badly. The service technician quoted $400.00 to fix a washer that cost me $800.00 new and is 2 years old. I had a Whirlpool washer and dryer set for 11 years with minimal issues and that is why I bought Whirlpool again. This will be the last time. It is a matter of time before the washer fails and I will have to purchase new or pay the service technician.

Purchased new Whirlpool washer from builder - never worked. Serviced 4 times by Whirlpool - does not wash, does not sense, shakes like crazy. No resolution from Whirlpool - worst customer service experience.

Whirlpool Gold Bottom Mounted Freezer - I advised Whirlpool that the refrigerator has two design flaws... one that makes the drain freeze up and even more importantly what is involved in correcting the problem. They replied that they were unaware of the issue when its all over the internet and has been for well over a year... maybe more. I sent them a couple pages of internet links and they said they would advise their engineers. As they have done with others, they suggested I should have gotten the extended warranty but that hardly addresses the problem(s).

The side-by-side with the lower freezer was one of my all-time favorite units Ive ever had. The capacity of the interior was expected to be better, particularly the freezer, but it was effective in getting to the items I needed. Storing was good, but the freezer had trays in the upper portion that I could see when looking down, as Im over 6 tall.

Whirlpool model N40T91 with FLAME LOCK - first failure was the controller valve only within 9 months of a new installation, replaced sort of free of charge, landlord had to pay ship charges. Days and days without hot water. About 6 months later, pilot failed to stay lit. Landlords maintenance man called Whirlpools Customer Service. They had him jump through hoops and finally told him to press a white reset button on the igniter. Okay, that worked. A few days later, pilot went out again, white button was reset, working again. Recently, and more frequent now, white igniter button keeps popping out, and we keep resetting it and relighting the heater, repeatedly, 4 times in one day.Maintenance man comes and calls Whirlpool Customer Service. They advise him to check this and check that. Everything seems to be in order. They say they will send out a qualified service person to diagnose a potential problem, a charge of $200.00. Maintenance man and landlord say, No thanks. Maintenance man goes to Lowes to buy a different brand model. Guess what? Envirotemp Hot Water Heaters have the same control device as the failing Whirlpool. He reboxed it and took it back and said, No thanks. Ill try to upload the images of the water heaters and controller you should stay away from purchasing. Meanwhile, maintenance man went to Menards and purchased a Richmond model, a well known, and reliable water heater manufacturer.

Whirlpool Duet Steam Front Loading Washer Model #WFW9750WW01 - The washer is only 5 years old and sounds like the space shuttle landing while in the spin cycle. Cost to repair parts only will be $896.87. The bearings among other parts are shot. I will NEVER own another Whirlpool appliance under any circumstance. Angry is putting it lightly!!!

We purchased a Whirlpool Cabrio Washer approximately 4 years ago thinking we were purchasing a top-of-the-line washer. The first year went great. I was very impressed with how it washed. My clothes came out cleaner than ever before; I loved it. But shortly after the warranty expired, one of the water pumps began leaking out all over the floor. We found out that a coin had passed through the barrel down into the pump and caused the plastic pump to crack with the high speed spin. We replaced that pump at a cost of over $100. We shopped around to find the part as reasonable as possible. The machine worked fine for about another 10 months, then it happened again. The new pump began spitting out water all over the floor. So again, we found another coin, another crack in the pump and again replaced it, another $100+. Finally, a third time, it was the same thing; the pump cracked due to a coin. This time, it was the pump on the opposite side, but still, water was all over the floor. This time, we ordered the part through Whirlpool and complained about this happening for a third time. My husband asked them about the Lemon Law and he was told that he would have had to purchase all of the pumps through Whirlpool. What does that have to do with it? We bought the pumps where we could afford them! The washer cost about $700 to begin with, and within 4 years, weve spent approx. $400 more? Thats not the end of it though. Now we are hearing loud noises and there is water all over the floor again every time you wash. This time, its not the pumps though. It appears that it has something to do with the bearings and maybe a seal somewhere around the barrel itself. But you can hear something knocking around - it sounds almost like a nut. We are going to call a local repairman to come and look at it tomorrow. This is just ridiculous. I feel like weve been completely duped over this purchase. The salesman talked this up like it was the cream of the crop and weve had nothing but problems. My last washing machine was a Kenmore and it lasted nearly 15 years and not once did I have to call a repairman or buy parts for it! Guess what Im going to buy again? If Whirlpool would just acknowledge these problems and fix them for people, it might renew faith in your company. I know I dont know the inner workings of a washing machine, but it seems to me that a screen prior to the pumps to keep coins from entering the pumps wouldve been a very cheap fix to a huge problem. I also own the Cabrio dryer and have hated it since the day I got it. It never dry things with one cycle. I always have to run it a second time. Knock on wood though, I have never had any breakdowns with that. I can guarantee my next buy will not be Whirlpool, nor will I pick expensive models again. I bought the cheap stuff years ago and it lasted forever! Im very nervous because I bought a Whirlpool fridge last year and I am praying I have no problems with that!

Cabrio washer 2015 model - The worst washer in 40 years. Everytime I use it I ask myself why did you buy this? Sure it conserves the amount of water but I havent noticed a nickel in savings because you have to wash the same load a couple of times. Since the days of cleaning in a stream clothes have been beaten to remove soil. How in gods name was I fooled into thinking this washer would actually clean our clothes. I put a folded tablecloth in it and when I emptied it the tablecloth was still folded. IF YOU NEED A CLOTHES WASHER TO ACTUALLY CLEAN CLOTHES, DONT BUY THE KIND WITHOUT AN AGITATOR. (serial # C52242825)

I have had this range for approximately 4-5 years with no problems. The design and efficiency are great!! I would recommend this brand to anyone and would purchase it again myself. It has an extra burner just for warming which I love.

I purchased a Whirlpool 50 gallon gas hot water heater 3 years ago. I have 3 daughters all in school age. When my old one finally quit due to tank failure and out of warranty, I went to Lowes and bought a 6 year warranty hot water heater costing around $600. Now I figured you get what you pay for RIGHT! WRONG! So about 2 years ago the pilot light started to just go out on occasion, a bit of an inconvenience but there was no default code warning me of any other issues. So typically we just relight it. I called Whirlpool to get help with this issue, but they wanted me to pay for a technician to diagnose the problem. Um isnt that what the warranty is for? I said dont bother. Im not paying $150 for someone to tell me what I already know. Ill just keep relighting it myself. So finally the pilot light goes out for the 100th time but this time I go to reignite it and BOOM! It sounded like a twelve gauge shot gun going off in my face! Then it flutters flames into the chimney of the hot water heater. Scared the crap out of me at first. But it finally stopped and run fine. Well Im laying in bed a few nights later and woke up to a loud thumping noise, I go down stairs and it stops. The following day Im in the kitchen and THUMP THUMP THUMP BURP BURP BURP. Run over to the hot water heater closet and theres the flames shooting out of the gas valve into the hot water heater then BOOM! Its out! The valve unit finally took a crap I guess. I call Whirlpool again to get my warranty - this time it definitely needs to be replaced. So the guy tells me the parts are covered in the warranty but a technician needs to look at it first and the technician Ill have to pay.. Excuse me but what the ** did you just say? I have to pay for a technician to look at your failing part? No I dont think so! Just send me the part - Ill replace it myself. Im a millwright electrician by trade. I specialize in power plants and refineries. Im sure this little gas valve wont be a problem. I spoke with these idiots on a Friday and he said I could have it ground shipped for free and it should be here in 5-6 days or pay extra for quicker delivery. What the hell did he just say? I could pay extra for quicker delivery on Whirlpools faulty part? ** whirlpool should be saying Well have the part overnight to you.Now since it was a 3 day weekend theres no sense in me paying $40 to have it delivered 3 day because it still wouldnt arrive until close to the five day. So I just looked to see where my damn part is because it shouldve been here by now according to the guy on the phone. NOPE! Its set to be delivered in 5 more ** days. DONT BUY A WHIRLPOOL PRODUCT. THEY DO NOT PRACTICE ETHICS.

This is a freezer on top unit. Purchased in 2015, unit quit cooling, started making a roaring noise. Called local technician, he added 2 oz of Freon, said he has seen many of these same unit losing Freon. Technician said line that goes to compressor is copper and hooks up to aluminum line before attaching to compressor. This is leak point for freon; no way to know when the leak started, but freon almost gone and cost to pressure check for source of leak is costly and probably would not repair problem. Got 6 yrs out of it and I am replacing with another brand. Will never buy Whirlpool again. Should have got 10-12 yrs of use. Do not buy this unit. Wrote Whirlpool first, but no help. Indicated this could be a problem with these units but no recall so I am on my own. Out $900 for a new refrigerator. Big hassle. Unit no good.

Refrigerator ice maker quit working. This is replacement fridge for first refrigerator that quit working same model. This one has electrical burn marks inside behind a panel. Whirlpool says this is normal. How can burn marks inside a refrigerator be normal. If house or fridge catch on fire will be suing Whirlpool. Ice maker and water valve replaced. Still not working. Maybe it has to do with the burn marks.

After reading all the reviews about the Whirlpool Cabrio washing machine, all I can say its just a piece of junk. We have replaced the agitator 3 times at $80.00 each, not including labor. Our clothes are never cleaned properly and it always seems to be out of balance. I will never purchase another Whirlpool product.

We just remodeled our kitchen and bought a Whirlpool kitchen suite in May of 2016. The refrigerator is absolutely terrible. I have had a repairman come out and fix the same repair/problem 5 times, a sheet of ice forms beneath the vegetable drawer (We have only owned the refrigerator for 5 months). Each time the repair person has come out it costs me a day of work due to having to wait all day for the repair service that Whirlpool hires out, well be there between 9am and 4pm. This morning I decided to check to see if the sheet of ice is forming again, it is. So I call Whirlpool again.Again, I call Whirlpool and ask if I can just get a new unit; 5 repairs in 5 months on a brand new refrigerator. The reply I get from Whirlpool is always well send someone out to fix it. The unit has to be deemed irreparable or a part has to be replaced multiple times. No parts are being replaced... no one knows how to fix it. I dont understand why a large company like Whirlpool would want people to write bad reviews for their products and customer service. Im extremely irritated with how I have been treated. I just want a refrigerator that works!! DO NOT BUY A WHIRLPOOL REFRIGERATOR!!

I wish I had gone on this website and read the reviews before I bought my washer about two years ago. I thought the Whirlpool Cabrio was going to be a good machine because of the brand name and because it is one of the more expensive washers. Like many others have said, I am disappointed with this washer. I bought it because it has a large capacity, but mostly because it has a hand wash cycle and a deep water soak. I have found that the only cycle that actually may get clothes clean is the Bulky Items cycle, because it actually covers the clothes in water. Some of the other cycles dont even get the clothes entirely wet. And the deep water soak doesnt wash the clothes, rinse them, or spin them dry. I might as well pre-soak clothing in my laundry tub, and then put them in the machine to wash them. Prior to this machine, I had a Maytag Neptune front loader, which did alright, but it had a few problems. I am ready to go back to the inexpensive agitator machine my mother used to have, if anyone still makes them. They at least got the clothes clean, and you could soak clothing if you wanted to. Im sorry that I bought this expensive washer. I wish I had bought a relatively inexpensive, simple machine. One good thing about this machine though is that I was able to wash a sleeping bag on the Bulky Items cycle. So, I didnt have to take the sleeping bag to the laundromat. Whirlpool needs to improve this machine or go back to the drawing board and create a new one.

In 2007 our Whirlpool 30 gallon gas water heater began to have issues. Serial number 0425126675, Model Number FG1F3030T3NOV. The pilot light kept going out and would not stay lit.. After several times with replacement parts being sent with the same thing happening, finally in 2010 they replaced the water heater. A new water heater was professionally put in, serial number 1023T412357 Model number BFG1F3030T3noHV.I am having the exact same issue and I was told that the warranty was null and void on the new water heater because it was a replacement. They replaced a defective water heater with a defective water heater. I called the number given to me by Lowes 1/877/817/6750. I spoke with Nichole. I told her that I should not have to pay for replacement parts for a defective water heater. I told her that I was never informed that there would not be a warranty. I live on a fixed income and cannot afford to buy another water heater because I was given a defective water heater in replacement for a defective water heater. I became angry stating, Thanks for nothing and I hung up. So many people have the same problem with these water heaters that something MUST be done.

We have a 2008 Whirlpool gas range that has worked reasonably well but lately more and more of the electronic push switches on the keypad have stopped functioning. So now I cant set an oven temperature as only a few of the 10 number switches still work. I talked to an appliance repair guy who said that the typical electronic keypads are notorious for burning out after 3-5 years because of heat transfer from the oven. So now Im stuck with an oven that is virtually unusable and a $400-500 cost to replace the keypad control. Is it worth replacing? Can the faulty control buttons be somehow fixed? Shouldnt Whirlpool acknowledge the faulty design and provide a free (and hopefully better) keypad? There must be thousands of people out there with similar circumstances. What about a class action suit? Any advice/opinions out there?

We purchased our suite of appliances from Home Depot, this was a great experience. Unfortunately that is were it stopped. Our 1st refrigerator caught on fire in the electrical within the unit. We got a 2nd refrigerator sent to us and it came damaged. Then they sent us a 3rd refrigerator and it caught on fire in the electrical as well. Weve been dealing with this all since August 27th 2019 and here its now October 14th 2019. At this point I feel this model of Whirlpool is truly unsafe.

I bought a portable dishwasher on 6/29/15. It didnt clean well, didnt drain properly. (I followed guidelines from the USER INFORMATION and used rinse). I called a plumber to clean out my pipes. My dishes were still dirty. I purchased an entire soft water system from Culligan. My dishes were still dirty. I called Whirlpool and Pacific Sales where I bought the machine, and got no assistance. On 10/2014 I spent $263.50 to repair and replace parts so the machine would drain. Sometime in January of 2015 it stopped draining again. I just got off the phone with Whirlpool who will not take any responsibility for this lemon. You offered me a policy to purchase for over $200!!! You want me to spend MORE money on a machine that never worked right???? How is that help? How is that standing behind your product? Then there was some lame offer to pay for parts, ONLY if I used your extremely expensive repair people and pay for labor, and $139 just to show up at my door. I asked who I can write to or talk to about this and was told by Sherri that there was no one to talk to but her. Really? Give me a reason to ever consider a Whirlpool product and to not slam Whirlpool whenever someones considering it.

As with other posts here, the rear bearing is going out of Whirlpool Duet front loading washer. I purchased mine in late 2008. Moderate use always according to recommendations. I called Whirlpool and same story--no recall and it would be expensive to have it repaired. I cant see putting $400 to $500 in parts even if I repair it myself. I cant believe that with such a common problem, Whirlpool wouldnt either honor a repair or offer a reasonable bearing package to fix. It requires the entire back, half of a new drum. Poor design, but whats worse is no effort by Whirlpool to rectify the situation.

A total loss of money. Does not use enough water to clean clothes. Gets out of balance all the time. Do not buy.

Whirlpool side by side refrigerator Gold series - I smelled something electrical burning and noticed black smoke billowing out of the back of the refrigerator. I pulled the refrigerator out and unplugged it. I took off the backing and saw a little white box that was on fire. When I unplugged it, the fire went out. I plugged the refrigerator in again and it went up in flames again. This could have been a lot worse. My smoke detector did not go off. It was 12:30 am and was getting ready for bed. If it had been an hour or so, Im afraid this could have ended a lot worse than a fridge full of groceries gone bad. I googled refrigerators catching fire. There are at least five videos with the same problems which lead me to believe there are several more out there. Why hasnt this been recalled?

I just purchased this washer Whirlpool Cabrio. Im experiencing the worst with it because it seems to take forever for it to wash. I came to look at reviews to see if other people were having problems like me. My issue is when I put it on quick wash it seems to say 41min then to 56min then goes down again and up again. I feel like its using more water as many times I hear it filling and washing. I didnt see anyone complain on that part but for the price its a big headache and upsetting because I spent that much thinking you get what you pay but I rather have the old washer I had than this. If anyone has had this issue please let me know and was it an ongoing thing. Not sure if you can comment back to reviews but shame on them to see all these unhappy people and not trying to make things better for them. I wish I read reviews before getting it. Yes it looks good on the outside but is crap.

On April 10, I bought a Whirlpool washing machine with a sensor. My clothes do not come clean. The dirty spots are still visible. I had three technicians come to check it out and after they just made the machine start, make the water run, and make the water empty, they confirmed that it was working normally. I have insisted on having someone come and just do a small wash and they did not agree because they are not there to wash clothes. I went back to Leon’s where I bought it and the saleslady told me that she could not do anything about it. I have been dealing with the customer service and the person has tried three times to get someone to come and check the washer properly and was insisting in front of me that I wasnt at all satisfied with the performance of the washer and still confirmed that the washer was working fine. They keep saying that there are no parts that need to be fixed or exchanged, so that means there is nothing wrong with the washer. I have tried all different kind of soaps. They were suggesting that I use Tide, which was the best performing soap. I used Tide or Purex - I even tried half a bottle of bleach - and it would not clean my clothes. The problem is the clothes are not turning, they just hardly moved with water that just keeps the clothes humid. I tried putting in more water with a bucket and when I push the start button, it would drain out all the water that it did not put itself. Ive called the consumer protection and they have advised me to take legal actions against the company and the store that sold it to me. They confirmed that whatever we buy, the article has to do the work it was made for; so the performance of a washing machine is to wash clothes. I even took a three-year prolonged warranty and the store told me that once the one-year warranty with the company has expired, then they could help me with sending their technicians and see what the problem was and they would take it from there. I have an account with the store and I have eighteen months to pay it off. So I was wondering if the saleslady did sell me an appliance saying that it was very good and that I should not have any problems with it. Can I take steps going against her for false advertisement? It’s a month now that my clothes are not washed properly and I need to rewash them by hand before putting them out to dry. The consumer protection office has been telling me that the store should be the one to finalize the problem with the company, but it seems that not even they can come to an agreement. Whatever steps I will take against the company and the store, what are my chances of getting my washer replaced? Whirlpool has been advised about me taking them to court and I got permission to do so. Actually, they invited me to go ahead and do what I thought was right. I do not have the money or time to waste on something that maybe I will have no chance to get anywhere. All I want is to have it replaced with another washer that would be more performing. If anyone has had the same problem and had their case solved, maybe it will give me hope to go on. Please, what is the best and fastest way for me to get this problem resolved? I do need a washing machine. I do need to wear clean clothes. Thank you for your patience and understanding.

The Whirlpool refrigerator I ordered from Home Depot came to my house dented. I then had to get Maytag/Whirpool to send me the same model refrigerator which they then subsequently forgot to include the ice maker with the refrigerator. It has been nothing short of an act of Congress to get in touch with someone from their Customer Service department for them to send the ice maker that they forgot to include. Ive had to call them at least 15 times to get them to resend the missing ice maker. Absolute nightmare. 10/10 will avoid buying Whirlpool in the future.

This French Door refrigerator looked beautiful. There are only two of us in the home. We purchased it at the end of 2014 and it just keeps getting worse. The front of each shelving has cracked. They look like they are dried out plastic the way it cracks. The drawer tracks have seem to keep crumbling pieces off. This is not a cheap refrigerator by no means, this is the first time buying Whirlpool, and I believe the last time.

We bought all new Whirlpool Gold appliances for new house. Fridge stopped cooling within 8 months, placed warranty call, couldnt get to us for a couple weeks (this is in July). Was told everyone was having problems...so sent us a brand new fridge...happy!! Little over a year later started having problems with this one and was told no warranty, didnt transfer to new fridge and no one offered to sell us a new one at the time, so repairs were out of our pocket. Had new condenser installed, still no ice, had circuit board installed, got ice but refrigerator section isnt cooling after almost $700 out of pocket...dont waste your money on a Whirlpool. So disappointed.

I bought a Whirlpool top loading washing machine with dryer on top, model # WGT4027EWo, last August, not even 3 months old and noticed the lint was not coming off the clothes. We tried cleaning out the washing machine with vinegar, wiping down the sides, using smaller loads and even used the gentle cycle. Nothing helped. We have had 2 different repair men out and they said there is nothing wrong with the washing machine and to put the clothes in the dryer and use fabric softener. I have never had to use fabric softener in my washing machine to get my clothes clean. When reaching out to customer service, I have spent over 2 hours and no satisfaction. They state that the technicians say there is nothing wrong with the machine. I was told by both of the technicians that they removed the lint trap from this machine, but no one is taking responsibility. My whites have blue lint and my darks have white lint, so too strong an agitation, as suggested by one repairmen is completely wrong! What to do when you spend over $1,000 on a washer/dryer combo and they dont work correctly and Whirlpool doesnt stand behind their product? Honestly, I will never buy another product from this company, and I 60 y/o and never made a complaint before about a appliance in my life!!! I dont even think I can give them 1 star! DO NOT BUY WHIRLPOOL - CUSTOMER SERVICE IS HORRIBLE!!!

Front Load Washing Machine, Model WFW97HEDBD0 - This is the worst appliance we ever owned. Purchased in 2015, multiple problems since! 1. Soap dispenser did not dispense and leaked down the front of washer... 4 service calls, control panel finally replaced, clothes not clean, leaking continued. Had to place soap into washer drum. 2. Pedestal drawer made grating noise, track off, drawer replaced, opened better but still made irritating noise. 3. Grease oozing from side of washer both sides. Decided to look in back of washer and OMG! A copious amount of grease is also beneath & behind the washer & dryer. I had to scrape with a metal spatula device to pick up and it took over 1.5 hours to remove & clean. We are lucky a FIRE did not start when using either machine. This machine was a LEMON from the beginning. In fact when we were having it serviced, I stated I wanted it replaced but was informed 2 visits were counted as 1 and did not qualify for further investigation. We cannot rid ourselves of this machine fast enough after the last issue. New washer coming tomorrow, not a WHIRLPOOL! New machine is LG WITH 10 year warranty on motor.

I purchased a washing machine and dryer 1 year ago. Since then it has started to get spots on the control panel where you select size, temperature, etc. I also purchased an extended warranty through Home Depot and is still under warranty for 3 years. I was told for a few more days is still under man warranty. I contacted Whirlpool and they said it is not their problem and sounds cosmetic - I think this is unfair being that I spent a lot of money and it has started appearing on the washer and dryer. No one wants to be responsible. I am a consumer who is very careful and have not had any spills or cleaned it with anything.

Very bad model Whirlpool washing machine. Pls dont buy any customers because from the date of installation its a headache for my family. I have a trust on whirlpool company but now I dont have. The problem is in every water select mode the tub is filling full and overfilling from the top always room fully with water. I hope the machine is not sensing water level. Such a bad experience from whirlpool company. My review is genius. My date of purchase is 28/7/2021

My Whirlpool Dishwasher Model# DU980QPDP, just quit a few days ago after 21 1/2 years. We paid $554.04 for it back in 1995. It was the top of the line. Quiet, with 4 fold down shelves on the top rack. Silverware basket on the door. Also a separate knife basket on the door. It came with extra interchangeable door panels. When the white ones got dented we changed to the black ones. The racks are still in good condition. Never had one repair on this dishwasher, though I used it every day, sometimes twice a day. It had a 4 year warranty on the control panel and a 20 year warranty on the tub and door. We would have it repaired, but cant get the part.

My dog is afraid to be anywhere near my Whirlpool side by side fridge. It makes horrible noises every 15 minutes to half an hour. I have to coax her to even let me escort her past. It has been snap crackling pop for several weeks and is getting louder with thumps and clangs. It does sound like the devil inside. Appears to be coming from the freezer side.I do not have the ice maker hooked up . It is plumbed for an ice maker but the servicemen who delivered it advised me they didnt do that . I didnt have the money to hire a plumber. The fridge was a PG& Energy Partners project in which those of certain age and income levels were presented new energy savers in exchange for old ones.Wish Id have kept the old one, especially after reading comments here. A senior, I live by myself in a fairly isolated area. I wonder now if the noise means a fire or electrical problem is imminent. My model number: ED2KVE*V*O, ED2FHE*V*O*

My Whirlpool microwave oven is terrible. The whole point of a microwave is to cook things faster and make ones life easier. The main problem is food doesnt actually cook due to sensors. Cooking bacon, for example, should be a simple, quick item that easily cooks in a microwave within minutes. Not w/ this Whirlpool! The sensor would not allow the bacon to cook - even after 20 minutes of trying!! Foods such as Bob Evans family sized mashed potatoes cant be cooked either. The sensor in this microwave ensures that only the outer layer is hot while the middle is stone cold. Also, the fan has never worked from day 1, and were now on 6 months of ownership. This wasnt a cheap microwave either, so Im SOL. Please dont make the mistake I made. Dont buy Whirlpool.

Near the beginning of September I started having trouble with my dishwasher. I called for service to be informed it would be a week before someone would be able to see to my broken dishwasher - which of course is a long wait just for a diagnosis call so decided to call another provider to get my dishwasher fixed in a more timely manner. The repair person informed me that it was the control panel but he suggested we call Whirlpool in order to have it fixed as the part should be covered under warranty. Much to my sadness I had to call again for an appointment with Whirlpool to find out I would wait for a week for a repair person to come out even though I already knew it was the control panel and asked them to order the part right away.Sept. 13 repair man from Whirlpool affiliate comes to my house for about 10 minutes to tell me what I already knew - it was control panel and maybe 1 other part. Cost $99.00 for just 10 minutes - Wow! Then the repair person said he would order the part right away /estimated to be back Monday September 19th great! Two weeks go by we have heard nothing about our part or possible repair of our dishwasher. Call Hurst appliance to see what is happening to be informed the panel is on back order - and they have no clue when it will be available. I should call the manufacturer. Call manufacturer to be told part might possibly be available - Oct 5th - from the United States from somewhere out east in Canada. Who knows? Oct 5th comes and goes as of Monday October 11 have heard nothing about my dishwasher and when it will be repaired - phone manufacturer - by the way which is in Tennessee. What a joke!She says the part is still on backorder but that a replacement part for the back ordered part is miraculously available - she couldnt tell me when that came about, so still have no clue when my dishwasher will be fixed. They have offered to reimburse me the $99.00 service call, but seriously should it take over 6 weeks to have your dishwasher fixed. I still have no clue how long it will take for the part to get here and installed. For 2 cents I would return all my KitchenAid appliances but especially my dishwasher. $99.00 does not appease me. I would like them to cover the labour to fix my dishwasher or a new dishwasher. What garbage and asked to talk to someone higher than the supervisor Gabby of the customer service dept. and was told she is the highest person in Whirlpool I could talk to - thats a joke. Shame on Whirlpool!

I was having trouble with our Whirlpool water heater and thought that wed have to shell out and buy a whole new one. Chris saw my complaint and helped me find the right replacement kit at a minimal cost, as my unit was out of warranty. He even took the extra step and overnighted the parts for us at no extra cost. I was extremely impressed with Chris professionalism and customer support skills.

Within 10 days of installing our new Electric range the cooktop does not look new and although we have used the prescribed cleaning methods, will not remove some cooked on spills over one burner and another burner has white rings around the glass above the dual zone cooking element. While we did not choose the top-of-line model; had expected much greater durability and appearance for our new range. My call into Whirlpool service made me feel like mine was an extremely isolated case and yet nothing would be covered as would be classified as customer fault. Highly disappointing as the cooktop on the range that we replaced seemed so much more durable.

We have owned refrigerators for over 40 years. Never had one as bad as this. Three ice maker replacements lasting maybe from 6 months to 2 years. Cap that off with customer service people who by voice and tone could not give a rats ** about helping the customer. Today it took me from 3:10 pm to 5:30 pm to get a real person on the phone. When I did the attitude is so reminiscent of a fast food hamburger joint with arches. Yes they know the refrig and ice maker are and have been a problem but they don’t care cause we have no option. Whirlpool will NEVER SEE ANOTHER penny of my money. Time to look at real appliance makers. Horrible.

Bought a Duet Whirlpool washer a couple of years ago. After about 6 months, it started to make a lot of noise like a jet taking off. Where we live there isnt a repairman thats able to come and fix it. So we would be required to have it shipped away to have this done. The washer was purchased at The Brick when we bought our new home. When we told The Brick of our problem we were directed to call Whirlpool directly - this we did and like everyone else we were given the runaround with no compensation to come. I will never buy another Whirlpool product again.

I have the 4.3 cu. ft. washer. This washer worked OK, but the lid lock does fail after about one year if the washer is in an environment where moisture may be present.I noticed the lid lock not working all the time about two months before the warranty expired. If this happens, call the warranty department immediately. After checking the ground wire and resetting the washer power over and over again, the lid lock finally stopped working completely. Here is how to fix it:There are two screws on the back of the top portion of the washer. Unscrew them from the silver straps. The washer lid will now push forward and up and off. Prop it up with a stick.Unscrew the two screws on the lid lock and start taking it apart (after reading this entire review). Be careful not to lose any parts and be sure to know where everything goes for re-assembly. Take pictures if necessary. Take the lid lock completely apart including any small pieces.The plastic slide needs to be cleaned. It has a spring that may fall when you pull it apart.The metal contact points inside the lid lock mechanism need to be cleaned. Be extremely careful when pulling the red cover off of the housing assembly. Pull the four metal contact points completely out of the plastic assembly. Be real careful with the black plastic slide piece, the metal rocker switch and the switch actuating motor. Use a small file and rubbing alcohol to clean off any green or white corrosion. Make sure to check all contact points.Re-assemble and you will immediately notice the lock switch working better. Re-install onto the machine. Re-install the upper portion of the washer. Start your laundry. Repeat after one year or when the lid lock becomes faulty again. These points should have been made out of a less corrosive material. Poor craftsmanship. Would not recommend.

Whirpool WFW9550WW-00 Front Load Washer - Washer was purchased 08/09/12. No problems until 07/12/15 when washer stopped working mid-cycle. Motor control board needs to be replaced, actuator needs to be replaced. $500+ Our local appliance store suggested we call the Whirlpool customer relations number and ask for the parts to be sent free of charge. We would pay labor. They gave us the model number, serial number, the diagnostic info. Long story short, customer service told me she didnt know why I was told to contact them. They can not predict the life of a machine. Less than 3 years for this machine. 22 years for my old Kenmore. Our old Kenmore never had a problem, but we thought that we should replace it in 2012 in case something happened with old machine. WISH WE KEPT THE 22 YEAR OLD KENMORE.

I purchased this range/electric (ygfe461lvq0) two years ago. It worked fine, but once about a year ago, the oven overheated and the breaker had to be turned off to stop it. No error codes were displayed. Year two, the oven broiler element stays on regardless if using bake or broil. Oven will go into runaway mode and breaker or cancel button has to be pushed to stop it from over heating. This range is a fire hazard and should be recalled regardless of what age it is. I called Whirlpool at Sears which recommended a tech who arrived to tell me that the control board is shot and for a price of around $400.00, it could be replaced. What is up with that? I had to pay for the expensive tech, also for 15 minutes of work. Sears says that I should have taken the extended warranty plan for around $160. Do I have to pay for an extended plan to have my house burned down due to a defect in manufacturing from Whirlpool? This is disgusting that a company can get away with crap like this. How do you people sleep at night?

I have had a $3000 GE Profile fridge for 6 years. It died. Tech says turf it. I bought a whirlpool. Hopefully it lasts longer. These expensive fridges seem to be very undependable. What is a family supposed to do when a refrigerator stops working and repairs take days or weeks? Is there a courtesy fridge for a loaner? They are big and heavy. What a royal pain.

11 months after I bought the fridge it started acting up. I paid 1900 for this thing. The temp kept getting warmer and the ice maker quit working. I had to pay for a service plan. Ill never buy a piece of junk Whirlpool product in my life again and ill broadcast their poor quality to everybody in my 5000 congregation. I work to save up to buy this product and its junk. Ill end donating it. Im very upset at this junk product produced by Whirlpool.

Whirlpool water heater FG1F5040T3NOV - I noticed that when I was taking a shower, my hot water wasnt working. I went downstairs and the pilot light on my water heater wasnt on. I tried to restart it. The pilot light wouldnt work or relight. I gave up and contacted a plumber. I dont feel I should have to pay for a plumber when its a product flaw!

I bought a Whirlpool built washing machine on Jan. 8, 14. It stopped working on Aug. 9, 14. It is now Sept. 2, 14 and I am still waiting for it to be repaired. I am age 75 and it is difficult to load and unload clothes to take them to the laundry. The repairman order a part Aug. 26. Pony Express has not deliver the part at this time.

There seemed to be an issue with the Whirlpool Cabrio Washer Pump. If a button comes off from your clothing or snap, etc., it gets trapped in the washer pump, causing it to crack and leak. Whirlpool on warranty only allows for one free change and anything after that costs $300.00. This is going to be the third time we are having problems with this and it is becoming, economically, a struggle for us. We have checked every button and snap to make sure they are fastened tightly, as well as any other type of items that may fall off in the wash and become trapped in the pump causing it to crack and leak. These pumps were poorly made and Whirlpool needs to be more aware of this problem rather than telling the customer that they are not aware of the situation.

This refrigerator well paid for itself. I had over 25 years and it was still in good working condition. I had to leave it behind. I moved to a place where fridge was already. I hated to leave it behind. ‘twas offered to Goodwill but they never answered the phone for it. I surely hope someone got it.

I purchased a set of Whirlpool Cabrio Washer/Dryer. After 12 uses of the dryer, it doesnt work and now I have to pay for the service. I didnt think Id need an extended warranty since my other 2 brand name washer/dryers lasted 15 years!

In July 2018 I purchased a coin operated commercial front load 27 in washer and dryer. It was placed in and used in a six unit apartment building occupied by 8 long term adults. Prior washers and dryers had been operational for years with minor repairs at times. In June of 2019 the interior cement center balance on the top of the washer drum broke with resulting damage to screws securing the center balance and potentially other unknown parts. This was reported to Whirlpool customer Care service and they referred me to one of their a repair services. The repair service in about early August repaired the washer.In late September 2019 the cement balance broke a second time and this was again reported to Whirlpool service who requested I notify their recommended repair service. On inspecting the washer the repair service stated the entire washer was required to be rebuilt. The labor for installation of would cost me $1,125 with Whirlpool providing the parts under their warranty. The $1,125 labor cost was just under what I paid for a new coin operated front load washer. I reported this to Whirlpool whose supervising staff, without any inspection of damaged washer as to determine whether the washer was fit for its purpose when sold as a commercial washer, rejected any replacement of the less one year old washer and insisted they would only pay for the parts and I would have to pay for the labor, particularly when the both the cost of the replacement parts and the labor would be substantially in excess of a new machine. Due to time and effort constraints the problem was resolved by simply dumping the defective washer and purchasing a new commercial front load washer from a more responsible company.

Whirlpool Dryer Model WED4815EWO and Whirlpool Washer W10682799 - I have always had great results with Whirlpool products. Both are energy efficient and save on operating costs. I purchased them three (3) months ago. The washer locks during the wash cycle. That took a little getting used to. I have always been able to rely on Whirlpool products. The top loading washer (W10682799) is energy efficient and high capacity. It regulates the water level so you dont have to worry about wasting water. The matching Dryer (WED4815EWO) has a sensor to regulate your drying time or it can be manually set. I appreciate the worry free, self-regulating functions on both the washer and the dryer.

Three days ago my washer Whirlpool Caballero has made a loud jet noise sound while spinning. While researching for a repair Ive noticed many complaints about this type of washer. Is there any resources that will help me get this repaired?

Whirlpool Cabrio - Our washing machine just started leaking water with oil underneath. This would be our third repair since purchasing this machine but it doesnt sound like a repair is possible or worth it. Its too bad we cant go back to the old models. They definitely lasted longer with no problems. Companies should make the older models bigger and forget about the front loaders and newer models without the agitators. Too much shaking in the machine causes too many repairs!

I think the whirlpool washer is a very nice machine. I think it does a good job of cleaning but still has the tub odor problem that a lot of front load machines have. As far as reliability it has done pretty well but I did have to replace the tub bellow and it is only 5 years old. It also makes a lot of noise so it is not a quiet machine at all. The steam option on the washer is a nice feature but not sure how much it does to help clean stuff.

I purchased a Whirlpool top load 8500 washing machine from LOWEs two years ago. I noticed that the clothes were not getting wet, clean, were coming out covered in lint, soap film and stained. It is misleading to call it a HE washer since I have to wash each load 3 - 4.5 hours. It is NOT energy efficient if you have to wash each load of clothes 3 times with a rinse. I have tried all of the tricks - changing soaps, labeling the wash as bulky, wetting the clothes to add weight... Washing clothes should not be this complicated. The clothes are sorted appropriately and washed in the right temperature. I do not understand what is staining the clothes. I put new white towels in and they come out stained (see photo)? Lowes sent out a repairman who said the machine would never clean the clothes since there was not enough water in the washing machine to wash the clothes. I tried to return the washer to Lowes but they said it was past the 30 days. Unfortunately, I purchased the appliances on a Lowes credit card so there was no recourse. I then contacted Whirlpool and was put on hold and transferred to various people before I gave up.

I purchased this washers predecessor, the WTW6200 in May of 09, along with the matching dryer. The bearings gave out after 36 months of use, and our household comprises two adults in their mid-fifties. Estimated cost of the repair? $650! Why am I posting this here? Because two weeks ago, my daughter-in-law called to say that shed so liked my machine when she visited in 09 - Id had the thing for two weeks at that time - that shed bought the WTW8500B and... the bearings were already giving out. I suggested she get the thing repaired, sell it immediately and replace it with an LG product, which is what Ive done.She has been put on a three-month waiting list for the repair, confirming my feeling that Whirlpool, as a whole, has gone down the tubes. Their service record is dreadful, with an excess of 20K complaints existing at various consumer agencies regarding ALL the Cabrio line, and their warranty, Ive learned, is considered the worst in the industry. All in all, the single worst purchase of my fifty-odd years.

I bought a Whirlpool refrigerator, model # wrt779reyb00 with serial # vs13537798. The icemaker quit working and then water started leaking out from the door. A&E serviceman came out to repair and said we needed a new door. It had been over 11 weeks and the door still has not arrived and we have been told it could be as late as November. When I purchased an item, I expect it to work and if not, to be repaired within a reasonable time or be replaced. I have called and been told that replacement is not an option and that I will just have to wait. This is unacceptable. I purchased this refrigerator with water in the door and an icemaker and I expect it to work.

Whirlpool Duet - they are highly rated and are aesthetically pleasing. Highly rated, they are expensive, my last Duet w/d didnt last as long as expected. Ive had to repair both machines once since I purchased them. Good quality is of utmost importance, plenty of washing and drying options, front loading washing machine, full size extra large capacity, attractive machines, good reputation for quality and lack of repairs.

I bought a Whirlpool Duet washer and dryer. The washer is model W9740. Less than a year later, the spin cycle sounds like a jet engine ready for takeoff. I got the extended warranty. A & E service tech showed up. The rear bearing and both halves of the tubs need to be replaced. The cost is $1423.33 to repair. It’s more than the cost of the set. I’m still waiting to see if the warranty covers it. I emailed Whirlpool to let them know I was **. I had a chat with someone named Laura. She disconnected from me after I told her to tell Whirlpool CEO they suck! Never again will I buy a Whirlpool product and I hope they go broke!

I purchased a Whirlpool gas top range from Lowes in Somerset Ky September 2013. Model number WFG524SLAB1. The surface is showing bubbles. I contacted Whirlpool and they gave some kind of story. In other words I am stuck with it. Still under warranty but they wont send someone out to look at it. Lowes told us that it could be a paint defect when it was made. If the top starts peeling, it will be a real mess. I have never used anything abrasive on the stove top. As of right now I am not happy with Whirlpool at all and if they dont do something about this, I will never buy another one of their appliances.

I purchased this washing machine December 16, 2011. I paid $737.07 for this machine. 14 months later I had to repair the top of it which cost me $255 for the lid which the plastic around the lid was cracked. I had to pay $136 installation fee and two years later the exact same thing happened again, the plastic cracked. I have contacted Whirlpool which took a complaint - said that was all they could do. Ive contacted the store where I purchased it, they can do nothing. I read online there are many complaints about the lid on this washing machine. It shouldve been a recall. I will never purchase a Whirlpool product again. I will not pay to have it repaired again. I will give it away and purchase something else not whirlpool and not from Lowes. I expected some kind of compensation from whirlpool on this. I have all my receipts.

I bought the washer Whirlpool duet on June 2009 (2 years and 2 months to date) and suddenly gave me an F70 code and died on me. It would cost me about $550.00 for parts and $129.00 for labor which is almost $700.00 in total. Its a communication error code where the CCU or the Motor Control Board was the culprit. I called the company for a concession consideration and they said they go by the warranty period. I should have read reviews for this company washers. Now, I have to find myself a better washer. I will never buy Whirlpool again. What a ripoff!

We purchased Whirlpool Cabrio Washer Model #WTW7300DW0 and Dryer in 2013 from Home Depot. The washer is the worst appliance we ever owned. It makes a horrific metal rubbing noise during agitation. The Whirlpool assigned repair service provider, after 2 trips and $300 has been unsuccessful in repairing the problem. Even after he called Whirlpool direct for assistance. Given that we used a Home Depot Gift Card for purchase, the repair expense is rapidly diminishing any benefit to keeping the machine. Well not even consider purchasing Whirlpool again.

Less than 1 year ago, I bought a washer and dryer. From the beginning, we have had a water problem and the water only comes cold... no warm water in the normal cycle. They came 6 times to service the machine and they cannot fix it. They said there is nothing is wrong with the machine but it does not wash with warm water in the normal wash cycle. I advise not to buy this product anymore. It is under a warranty so they should fix it or replace it. I am sick and tired of talking to them. They said if we send the service guy then I have to pay for it which is not acceptable because it is under a warranty. If anyone is thinking about buying this product, I advise not to get it and waste money on it.

We purchased a dishwasher for $650 and within a very short period of time, the upper rack was so squeaky that it was intolerable. Service guys came and replaced the rack and wheels and all was well until a few months passed and it happened again. At that point, it was outside of the warranty, so we called upon our extended warranty we bought through Whirlpool. Guess what? That warranty doesnt cover the racks. So they referred us back to Whirlpool. They told us we had to pay for it ourselves. After being treated like a ping pong ball several times, we ended up paying about $150 for labor for another guy to come out and replace the racks again. Whirlpool agreed to pay for the parts. A few months later, we again have a squeaky upper rack that is so loud it wakes people up in our house and its less than two years old at this point. Weve been sold a LEMON!! Just got off the phone with a supervisor at Whirlpool who said they cant do anything about it and wont acknowledge we have a lemon. When I told her I was going to take this as far as I need to to resolve it, even if we have to go to court, she laughed out loud at me. We will never again buy a Whirlpool product. Our LG appliances have been great however.

I spent the extra money and bought a very nice looking Whirlpool range and oven. Within months, it started rusting. I keep a meticulously clean kitchen and Ive never had this problem with any other appliance. I sent letters to no avail. They said that their warranty on rust was 30 days! They refused to do anything about it and told me to go ahead and sue them. Terrible product. Defective from the factory. Do not ever buy a Whirlpool product as they do not stand behind it.

Whirlpool duet - I have had this machine for 4 years and have gone through as many door gaskets. They rip in no time causing damage to clothing and with the leaking damaging my wood floors. A definite do not buy!!!

In October 2009, I purchased a Whirlpool Energy smart gas water heater with flame lock safety system.$509.00 I had it installed on 5/4/2009 by Westmoreland Affordable Plumbing, $218.00. On 10/15 called Whirlpool stating that the upper thermistor was coding as a failure. They sent me another one to replace it on 10/19/2009. On 10/19/2009, 1 and 1/2 hours later, the tank was coding a bad gas valve, called back and told Whirlpool what had happened and that I smelled gas. I shut off the gas to the water heater and waited for a valve replacement to arrive. On 10/21/2009 I had E.H. Plumbing to install the new gas valve to the water heater, $150.00. On 10/28/2009 the new gas valve went bad. I contacted Whirlpool and argued with them until I had them replace the hot water tank. With their approval I went to Lowes and tried to get the same water tank but they no longer sold that model anymore. I was given their equivalent to the one I had purchased earlier. I had it installed on 10/29/2009, $150.00. I now see a class action suit was filed against Whirlpool for the model in 2008. They were still selling this model after the lawsuit???? I spent $1027.00 for a $509 hot water tank and a lot a days without any hot water. I have all my receipts and returned codes for this transaction. Is it possible to get my $300.00 back (for two extra installations) as a result of this problem? I also kept the old gas valve thermostat.

We have a Whirlpool double oven that is about 3 years old. Today we used the oven for lunch and about 2 hours later we heard a loud sound from the kitchen. When I went to see what had happened I found glass shards all over the kitchen, some as far as 10-12 feet away. The outside glass of the top oven was spider-webbed and had apparently exploded. Nothing had come into contact with the oven and nobody had been in the room with it for over an hour, it just randomly exploded. I am going to contact Whirlpool but judging by the other posts I dont expect much help from them.

Have owned my Whirlpool washer model# LSR 701 0PQ1 two years and had no problems with it before today... The washer was used once a week since I purchased it and only myself use it. There is only myself and my son and our loads are always small. Well today I put a load in and went to finish my other housework and when I went to check on the load, there was a weird smell in my laundry room. As I approach the washer to put softener in the rinse I saw a flash behind on the left hand side of the control panel where the size of load and water temperature selection is. I unplugged the washer and put the fire out. Have never had anything happen like this before with this brand. I already know I have to buy another washer but am scared to get another Whirlpool.

My Duet Sport washer drum is damaged due to the poor quality of the bearings. I replaced the Whirlpool Duet Front Loader Washer Bearing & Seal Kit W10253866, W10253856 but because the bearings were damaged the drum is also damaged. When I opened the rear panel of the washer the bearings had literally come apart and bearings fell out. All of the floor and the oil/grease was everywhere. I replaced the bearings but it didnt matter because the drum is warped. Priced the drum and it is nearly $400.00 to replace the assembly. The cost of the drum assembly is about half the cost of a new washer. I will never buy another Whirlpool product again. Just a shame that the cost of a replacement drum is so high. What caused the bearings to just explode and damage the drum. What did I do to cause this? Absolutely nothing. I have since discovered that this is has happened to scores of people with this same washer.

In October 2009, we purchased a Whirlpool Cabrio topload washing machine for almost $900, because my wifes sister had a 1-year-old one and had been pleased. The Cabrio replaced a 3 1/2-year-old Maytag that died with a seized-up transmission. Maytag is also a Whirlpool product for those of you who do not know. We had issues at first with it going off balance but dealt with it. It was also taking 40+ minutes to do even a small load of laundry, but again, we dealt with it. Fast forward about 3 years, and we notice the machine is making really loud sounds during the spin cycle. I checked for any obvious issues but found none. The noise kept getting louder with each use. Finally, I called a repairman to check it out. His diagnosis was quick. The bearings were going bad in the machine, and he said it would eventually fail. He quoted me a price of between $400-$500 to repair because the job is very labor-intensive. I declined the repair but still had to pay him a trip charge. Then I checked with my wifes sister about hers, and she said hers had been making a very loud sound for several months but they were just ignoring it. I told her about the diagnosis of mine and advised her to tilt the machine back to look under it. Sure enough, there were oil stains under her machine, just like mine, indicating the bearings were failing. So we have 2 Cabrio machines, one 3 years old and the other 4 years old with the exact same problem. I called Whirlpool since I had registered the machine when I purchased it. They basically told me to go fly a kite since I had not purchased the extended warranty. They said I could attempt to repair it myself to save money, but they advised to have their repairman do the work. Well, no kidding. What a joke. They expect you to buy a $900 machine and have to replace it every 3 years. I am done with Whirlpool products. FYI, Kenmore products are also made by Whirlpool, so Sears is not an option. My wifes sister and we bought new GE washing machines, and both of us purchased the extended warranty this time. For $129 (5 years), its cheap, peace of mind. Whirlpool is crap. I would suggest never buying any of their products. I know we never will. Once they have your money, they dont care.

I had a Whirlpool GI7FVCXWY01. Purchase 3/13/2010. I had repairman after repairman come to fix it. The last one probably saved my family and my house. The light in the back corner was not only blinking, but flashing rapidly, much like some wild party light. It eventually stopped. The freezer works perfectly fine, the fridge works when it wants to. The ice maker makes ice some days but not others. The motor on the ice dispenser is completely frozen up. Does that all sound about right? If it does, clean it out and cut the power to it before someone gets electrocuted or your house catches fire.If you cant find the electrical diagram, or the company wants $455 to answer your questions, look under the right side of the freezer draw, but not on the draw. Remove the guard on the very bottom of the unit, near the wheels on the right side. You will feel a plastic bag attached to the underside. Inside that bag is the complete diagram of all the wiring harnesses along with the schematic for the amps and voltages for each wire. Are they telling your circuit board is bad and you will need a new one? Before you do that, inside the fridge compartment, in between the water filter and the ice maker, remove the light cover. Notice that inside that space is the access to another panel. Remove that panel. BE SURE THERE IS NO POWER RUNNING TO THE UNIT FIRST. Here you will find a connection plug with more or less 15 wires that are connected to the main wiring harness. Above that plug you will find a holding chamber. This holding chamber contains water from the filter that is waiting to go to the ice maker. It has dripped condensation on the plug since the day you first turned on your fridge. Your wires are most likely broken and corroded. You will need to have your unit completely rewired, but because of the design flaw that fix will only buy you another 4-5 years. My Whirlpool GI7FVCXWY01 left yesterday 5/15/2014 and none too soon.

We have had the same problem with the magnetron in our Whirlpool Microwave Hood Combination. Replaced this part in Dec. 2012 after warranty expired. Cost of repair was nearly cost of microwave. Magnetron went out a second time this week. When I called Whirlpool customer service, the management rep was very hard line about the warranty on the unit and parts. Very clear this company has a product reliability issue and does not want to keep its customers. I dont plan to purchase another Whirlpool product ever. What a frustrating disappointment!

We bought a Roper refrigerator about seven years ago. Less than two months later two of the cheap plastic door shelves broke and we had to buy replacements at over $20 a piece. Since then weve had to replace one more. Tonight another one broke so well have to fork over another $20+ to replace this one. I checked the Whirlpool website and they have the exact same flimsy plastic shelves as the Roper. I will be in the market to purchase at least three refrigerators in the next two years and you can bet that they wont be either Roper or Whirlpool. My advice to anyone in the market for a refrigerator to steer clear of these two brands as their shelving is cheap and shoddy.

Subject was included in our new condo less than 5 years ago. It appears that all we have to do is look at it and it falls apart. There is constantly another piece of plastic on the counter. Our experience in calling Whirlpool for service is that it is very expensive and time consuming. A refrigerator installed at the same time as the purchase had a defective ice maker which took three service calls and a final installation of a broken part by me before we were together again. 2 (two) service men recommended that if we had problems again that we do what they did. Buy Ice Cube trays!!!! What a great recommendation.

Both the washer and dryer make terrible screeching noise. The dryer only dries on time drying. The store I bought them from have been here over 7 times too fix them. They still are not fixed. Just a terrible experience with this set from day one, load one.

Water filtration unit was leaking only when someone got water. It pooled into the bottom of fridge and ran out under the fridge and because of the slope of the floor was running back towards the wall. We didnt notice until our laminate wood flooring was starting to swell up. It was probably leaking since the day we bought fridge brand new, but took us 4 months to notice. Whirlpool said they will not fix our flooring, only the fridge. We had to make a homeowners claim which we did. When the contractor moved the fridge back after replacing all flooring it starting leaking from the ice maker unit. Only when the ice tray filled it would gush out water. Our flooring is now ruined a 2nd time and Whirlpool will not fix the floor. Repairman said that Whirlpool used rigid parts in the water and ice maker units and tons of people are having the same problem. Since there is no flexibility in these parts they break when the fridge is moved. Whirlpool sucks and I am fighting with them and Lowes to get this fridge replaced with a non Whirlpool appliance. I will never buy Whirlpool again.