After almost 5 years of satisfactory performance, our $1200 Whirlpool Duet washing machine WFW9400SU1 requires repairs costing over $1100. Similar to another complaint listed, some parts rusted out, leading to extensive damage during use, which we realized only after the spin cycle became incredibly loud. Now the entire gut of the machine (bearing, drum, arm, casing, etc.) needs to be replaced - $900 parts and $200 labor. I trust my repairman (who said theyd seen this type of problem before with Whirlpool) especially because he recommended buying a new machine instead. I called Whirlpool, and they said they could do nothing for me which made me very angry. This is a mechanical problem that could have been avoided by using proper materials. Whatever happened to the washing machines that would last 15-20 years?

I purchased a Whirlpool range from Lowes for $750.00. After 13 months, the digital circuit board went out and cost $580.00 to repair. I thought this was odd since the range was fairly new. The service tech said the boards are a common problem. Two years later, when using the self-cleaning mode, the door was locked and the board was out again. So this must be the issue because that is the same problem that happened the first time. This must be a design flaw! The board cannot handle the heat generated in self-clean mode. Way to go Whirlpool, put the board near the oven door where it is subjected to extreme heat and melts!

Purchased the oven in summer 2015. Very disappointed in the AquaLift Self-Cleaning oven. Absolutely useless. Does absolutely nothing and I end up cleaning the oven by hand. As a senior citizen, this is uncomfortable; I have injured my leg in the process and now feel I must wipe the oven down after each use. I was so looking forward to having a nice clean oven at all times and its not happening. This is of no value to me.

Whirlpool cabrio top loader is junk from the first month. My washer has had way too many repairs. A&E repair has been a frequent at my home. Now Im getting ready to repair it again! Hub gasket or pump not sure this time. All has been replaced previously. Never ending - always something wrong with it!!!

Every one of the knobs cracked where they engage the gas valve. One gas valve came loose from the manifold creating a gas leak discovered by the propane company on a system leak test. Screws came loose that hold the tracks to the base for the slide out bottom drawer. The AquaLift cleaning system is useless. Better buy some oven cleaner and rubber gloves. Very disappointed! One star because 0 isn’t an option.

The front of the stove gets so hot you can burn yourself and I feel it is not safe around small children or grandchildren, and it should addressed to fix the problem not just cover it up. Please give me the info to fix the problem before I have to sue over my grandchildren and great children getting burned.

We have had our Cabrio for one year now and we found the agitation cycle to be loud but we have gotten used to it now. The thing we cannot get used to is the sour smell permeating from it. It smells like a dirty mop. Our washer and dryer are in a small laundry room so when we enter it to get to the garage or bathroom, the smell hits you like a ton of bricks. Stinky!!

On May 25, 2008, I bought a Whirpool Model# BFG1J4040T3NOV 40 gallon natural gas hot water tank. The pilot light went out today, Sept. 26, 2011, and it will not re-light. This was bought at Lowes and was rated as a 12-year warranty on the tank and parts. This is premature failure of a product that is listed as 12 years. Due to all the other similar complaints of this Whirlpool hot water tank, I would like my money back ($455.81) plus installation or a new tank installed.

Our machine was bought via the employee purchase program. Its just under 2 years old and the bearing has been out for nearly 6 months. I called Whirlpool and our local Whirlpool repairman. They both want hundreds of dollars to repair it. Being pretty handy, my husband and I decided to fix it ourselves. Trying to find compatible parts for this model is a NIGHTMARE. Everything in my house is Whirlpool...range, dishwasher (also junk), microwave, fridge, washer, dryer...and it will all be systematically replaced with ANYTHING BUT WHIRLPOOL OR ITS COUNTERPARTS.

I had purchased a washing machine trough CSD canteen and go for AMC for five years on September 25, 2006. In September 2010, I lodged a complaint and the Engineer visited and asked for a replacement of the bottom cover. I said okay, but later on he told me that I have to replace the complete outer cover. I agreed and asked them to replace it. The cost is fixed for 2,500Rs. They replaced the cover but did not replace the bottom cover.I talked to the agency and they agreed to hold to 1,000Rs for the bottom cover and I paid to them 1,500Rs. Later they brought an old cover and I refused to replace that. They told that the bottom cover is not available. Then they never tried to replace the bottom cover. I arranged for the same from the local marketing for 600Rs and replaced it. I paid the service charge for the engineer.Later, I lodged a complaint that the machine was not drying the cloth. The engineer visited and told me that the belt will be replaced on payment. I agreed and he told me that I will visit the next day and replaced the belt. But he did not come until it was late.On September 18, 2011, with number DL0911018283, my machine was not switching on and I lodged a complaint to customer care. But no engineer visited me. Then I regularly complained but there was no response from the agency. On September 23, I talked to customer care, Mr. **, that I am going out of station and I lodged a complaint from the last five days that no engineer visited me. My AMC is expiring on September 25, 2011. I will come back on October and then send the engineer. On October 9, I reminded them that they refresh my complaint with number DL1011007031. The engineer visited and told me that the PCB of the machine is faulty and I have to pay 3,500Rs.I told him that I complained for this problem during the AMC period, hence they are supposed to repair my machine free of cost but he refused. I talked to customer care and tried to resolve the issue but I was not successful. Then I talked to Mr. **, the head of Customer care in Delhi, on October 12. He promised to resolve the issue but no engineer visited me and my machine is still defective. On October 13, I tried to contact Mr. ** several times but he or his PA is not picking up the phone. Now, how will I get to repair my machine?

Our recently purchased stove top is an average appliance. The surface is easily scratched just from paper towels when cleaning. Today for no apparent reason the igniters all started firing and continued for a good hour....I would definitely investigate other brands before purchasing again.

I updated appliances in new house, but didnt realize the builder would choose the smaller side by side frigidaire. Could use a larger freezer space, also would like a ice maker that cut off when bucket is full. Overall I love Whirlpool appliances.

I bought a pair front loading washer & Dryer May this year and took Delivery in June. First problem was with touch controls. I should have Known then it would be trouble, they replaced it then we went home to Fl. - Aug. Returned in Oct - used the machine eight times total and it locked up with our Clothes inside in water. Called for service, was told it would be a week before someone could come, then was told after four days it was the mother Board and it would take at least another week to get our clothes out. Their Service is the worst I ever have dealt with. The whole house - we Bought Whirlpool based on the Maytags we bought for our House in 2004. Never a problem but those Maytags were Maytag - not whirlpool. I would never buy any Whirlpool Appliances again. It is sad because I try to buy American made to support our fellow Brothers and sisters in the work Force but now I will buy made anywhere as long as it works and has reasonable service. Whirlpool is not the same as I Remember from years ago.

I just purchased a new stove after using my old one for 15 years with the same great quality. Its the brand I will purchase when I have my retirement home built next year and leave my new one in the home for my son so he wont have to buy one for 15/20 years.

I bought this washer thinking it would last me for a long time. And now it wont wring out my clothes and I just wanted to say I am disappointed in my Cabrio Washer.

Do NOT buy this washing machine. It looks nice but that is all. My elderly parents bought this washing machine based on the past experiences with Whirlpool but the quality of the product has changed. This machine constantly errors and does not allow them to wash clothes. I have followed the instructions in the manual to try and clear the errors. I ended up calling Whirlpool and the response I got was... It will be anywhere from $80 to $125 for someone to come out and look at it. This is a product which should not stop working after 2 years. I guess Whirlpool only stands by their products for a year because they think it is only built for a years worth of service. I wish I had better things to say because the previous Whirlpool machine lasted over 20 years.

My Whirlpool Dishwasher Model# DU980QPDP, just quit a few days ago after 21 1/2 years. We paid $554.04 for it back in 1995. It was the top of the line. Quiet, with 4 fold down shelves on the top rack. Silverware basket on the door. Also a separate knife basket on the door. It came with extra interchangeable door panels. When the white ones got dented we changed to the black ones. The racks are still in good condition. Never had one repair on this dishwasher, though I used it every day, sometimes twice a day. It had a 4 year warranty on the control panel and a 20 year warranty on the tub and door. We would have it repaired, but cant get the part.

Cabrio Washer - Absolutely the worst thing I have ever bought... everyone told me to stay away from this brand. Bought in 2011... large tub... nothing but problems. My last washer was great... full tub with water, could soak or pre-wash. This one does nothing except create some kind of lint all over my clothes no matter what setting... I dont care about water usage (mine is free) but I do care it takes 50 mins to do a load where my other was exactly 20 mins (and it lasted me over 30 yrs!). This really sucks. I have seen other complaints but never a recall!!! NEVER EVER AGAIN!

This microwave had been the best I have used for several reasons. One is the modern design that goes with our kitchen. Two: it heats the food very quietly and produced an even temperature through out the food. Three; The inside of the microwave is easy to clean out.

A new washer, kept in pristine condition, indoors in an upstairs laundry room, used by 1 person for 4 years should NOT rust out. I took pictures and sent them to Julia ** a company representative after she offered me a discount on a new washer but would not send me an email with directions like it was some kind of secret until I insisted several times. The email simply had her phone number. I was to let her know the models I would be interested in and she would tell me if those were available for the discount. Then the company would charge me, deliver the new one and charge me to install and remove the old one. How is this for a great company. I sent her the models I might consider. No word back. Whirlpool, not looking like a stand-up company to be proud of. Shame on this company.I like the machine, but seeing it rust out before my very eyes has changed my mind. How will they address a 4 year old washer rusting from the inside out? How will they address a 1 year warranty? I found a copy of Whirlpool Washer Warranty that used to have up to five years for issues such as poor workmanship. It takes more than a year to find these things out. Dont make them if you cant guarantee that they will last. My last Maytag lasted 18 years and was still in good shape. I just wanted a model without the agitator in the middle and on that would conserve water. Should have kept the old one.

We purchased a Cabrio model WTW6600SB2 washer, it has lasted 4 years, then when the pump went out, we paid $200. To fix it then on the 2nd load, it went out, now the tech man says the motor is cracked and Im not sure if the motor is replaced, it will even work. I looked at the motor and it is made of plastic! Can you believe this? Plastic! I didnt believe it until I saw it with my own eyes. I will never purchase a Whirlpool appliance again nor will any of my relatives or friends if they ever ask my opinion.

This product deserves ZERO stars! I purchased a Cabrio washer - dryer in October, 2013. I have carefully followed the instructions for the washer. I am hugely distressed about the large amount of money I spent on a washer that is absolutely terrible, horrible, awful., no words can adequately express how bad this so-called washer is. The low-water washing has torn up all of my new towels in the matter of a couple of washes. It has completely ripped out the hems of the towels and pulled long ragged strings in the towel. And these were not cheap towels. I am mad at myself for not researching better before buying. I hope my complaint can save another consumer from the misery I am suffering because of this shameful product.

Ive had other brands of washers and dryers and I must say I always return to Whirlpool. They are well made and do what they are supposed to. Never had problems. My last set of Whirlpool was about 12 years old. Great product.

Im a renter, and I know the landlord purchased the least expensive stove for this apartment, but that shouldnt mean one has to absorb ongoing off-gassing fumes for well over a month now. The stove was installed 2-18-17, and its now 4-6-17, still havent been able to use it. Is this really off-gassing or is this what Americans have to contend with now! Oh and theres the little sticker that says Made in America and in small print it says designed and assembled in America, but no mention as to where the parts came from!!! The only reason Im giving even a One Star rating is because I cant continue through this review without at least marking one star.

I bought a Whirlpool refrigerator because it was the lowest priced model that offered a bottom freezer compartment and fit into our available space in the kitchen. We also want a white coloured appliance. One thing we never noticed until set up at home was that there were no ice making trays nor an ice bin. We have had the fridge for five years with no problems. It is quite noisy when running.

Absolute garbage!!! French door refrig/bottom freezer. Too much to go into. This is by far the worst product that I have EVER purchased in my life. If I was strong enough to lift this piece of ** over my head I would carry it into the corporate headquarters of these money grabbing dirt balls and throw it through the CEOs door. Amend that: I would locate customer service and consider them bowling pins. What a bummer; how far we have fallen!!!

After having my Whirlpool side by side refrigerator ice maker replaced 4 TIMES in 10 years, I finally found a permanent fix for it: an Igloo counter top ice maker for around half the price of a replacement Whirlpool ice maker. Unlike the Whirlpool ice maker, it makes ice. I promptly removed the Whirlpool ice maker FOR THE LAST TIME, and sent it to the dump, where it belongs. Goodbye Whirlpool! If that is the best you can produce, you will not receive any more of my hard earned money!

I bought a Whirlpool dishwasher from lowest in May of 2011 and it stopped draining, serial # f11601686. I was told it was under warranty and you sent someone out. But surprise, I got a $129 service bill and it couldnt be fixed, computer board gone and drain motor shot. I was told its cheaper to buy a new one. After 10 months of use, we need a new one. I think you should replace my dishwasher and pay for a service call. Oh, the reason they said it wasnt covered is because they sold me a 2007 model.

The washer can not spin dry, as the unit will not balance. When it spins, it will get out of balance, and shuts off. I have had a repairman out, but he said he can not fix it, and that this is common with your units, He suggested we get a new one, but not from Whirlpool.

We purchased a new home in July of 2011 and we paid extra for the upgraded appliance package, which included a Whirlpool Microwave/Convection Hood Combination unit. We have Model # GH7208XRS3. We use the microwave a few times a week and only used the home 6 months each year during 2012, 2013 and 2014, for a total of approximately 18 months. From the very beginning, we had trouble with the microwave control panel turning itself on and the electronics going through various timing and programming functions independent of any human operator.During the combined two-year warranty period from July 2011 July 2013 (the Manufacturers Warranty lasted one year and the Developers extended Warranty lasted an additional year) we had 5 service calls on the same issue. The Authorized Repair Center repairman called the Whirlpool Tech Line while he was in our home and was told that there was a flaw in the design of this model. They replaced the door and then when it acted up again, they replaced the control panel. In Nov. 2012, after the repairman told us the door needed to be replaced again, we asked for a new appliance since we had the same issue repeatedly and they had already tried to fix it by replacing the door and it was still under warranty. We were told that Whirlpool would not replace the appliance until they had tried to fix it three times and we needed to get a new door again. We were told that because it was the same issue repeatedly, we would get a replacement if it still went bad after the warranty was up. So we had the door replaced again, which did not fix the problem.In late 2014, we again had the same issue with the control panel and made a call to Whirlpools Customer Experience Center. At that time, we were told that the warranty was no longer in effect and Whirlpool would do nothing to fix the issue. Even though it was the same issue that they had attempted and failed to fix while under warranty, the company would no longer stand behind the promise of customer satisfaction and told us they will not replace a 3-year-old microwave. When I asked the Customer Service Rep to speak to a Manager to escalate the issue, I was transferred to the Tennessee Office. When I got the same repeated run-around from the Supervisor, Melissa, I asked that Customer Service Supervisor to let me speak to a Manager and she told me she could not give me the name of anyone else to speak with and hung up on me.I am writing to you to express my extreme disappointment in Whirlpool and the products reliability, the way the company has handled fixing the problem and especially in the conduct of the Customer Service department. Whirlpool gave us nothing but a run-around for the years the warranty was in effect, knowing that this model has a design flaw and trying to do band-aid fixes until the warranty ran out. We were told that our only option now is to pay to have the same problem fixed a fourth time or purchase a new microwave.Whirlpool has trained their Customer Service people to be polite but ineffective and obstructionist on the phone and then hang up on the customer when they cannot resolve the customers issue. I believe that Whirlpool should be committed to customer satisfaction and making sure that their products work as intended and fix the problem that was reported while under warranty, even if it no longer in warranty. Whirlpool should be as disappointed as I am that after three attempts the problem is still not fixed and should be committed to customer satisfaction enough to replace the appliance after three failed attempts.

Since my review I have been corresponding with Whirlpool Customer Service (Chris). First he sent me an email and mailed a replacement board to have us (the homeowner) install. Because the cover was so melted, the replacement board would not fit down into it. I emailed pictures to Chris. Once he saw the pictures, he called me and arranged for the water heater to be replaced since it was still under warranty. He even extended the authorization code so we would have plenty of time to arrange for a plumber to do the work. We had to pay for the plumber, but Whirlpool arranged for us to have a new water heater. Now I can sleep at night without worrying that my house would burn down if the old water heater caught fire. Chris was GREAT to work with. I had a direct number to him and called any time I had a question. I was very impressed with Whirlpools Customer Service.

Bought this washer two years ago. First experience was when a load of towels became wrapped around the agitator. Called in service tech who told me to load the bin with the cloths pressed against the bin wall away from agitator, as if the cloths/towels would stay away from agitator. Two years later, Im ready to the machine to the street. Forget sheets and bedding. The agitator wraps them so tight that I almost rip the cloths/sheets to unravel. I had to wash a pair of work pants that were soiled with mud three times and there was still a stain. I will NEVER EVER buy another Whirlpool product.

Approximately 2 years after purchasing a Whirlpool Gold side-by-side/counter depth refrigerator, I noticed cracks on the interior walls. This was in 2011. First, I contacted the service contract people. They told me this was not covered under the policy. Next, I wrote & called the company. They told me they could send someone out to EPOXY the walls. I told them this was not at all acceptable to me and that I believe this is a defective product. I have never heard of this happening to a refrigerator. I am also quite concerned that there are toxins emitted through these cracks. After a time with no response, I wrote them again.This time, they referred me to Ms. Alicia ** at the Exec. Offices. She wrote asking me to call her. After making several calls & leaving messages to no avail, I wrote her asking that she kindly write back to inform me what the company was going to do about this defective product. I cant help thinking they did not want to commit to anything in a letter because I never heard from her or anyone else at Whirlpool. Small Claims Court cannot help as the company does not have an office in New York. I am very worried about the possible health hazard this possesses. I am very careful to completely cover all food inside the refrigerator. At this point, the cracks have increased in size and new ones have appeared. I am very upset over the lack of concern and lack of response from Whirlpool.Ive owned many Whirlpool appliances through the years and trusted the brand. This is not a cheap appliance. Consumers dont expect to spend a few thousand dollars on a product just to dump it in a year or two. Given the size of the Whirlpool Corp., anyone would think they would simply replace their defective product to keep their reputation if not for the health concern of their customers, which should be a priority. Over the past few years, I have had increased respiratory problems and so have other family members. I believe its due to the emissions from the cracks. I will have to dump this defective refrigerator before it gives me cancer! Thanks Whirlpool, great doing business with you.

We bought a new Whirlpool Dishwasher. Installed it, wife used it for two loads. The third time she tried using it the door sprung and it no longer latches. After two weeks of calling Whirlpool, we finally had someone come out to fix it. After the repairman took a hammer to the frame he stated that it had been dropped. He wobbled the dishwasher back and forth with his hand. He said the frame will never be correctable and we will always have problems. After another week we got a hold of Whirlpool and were told the repairman has ordered parts to repair the dishwasher. Whirlpool is hoping it will hang together until the warranty expires. If the dishwasher were fixable that would be fine. However, when the repairman who has years of experience in his job tells me it will never be right and will always be a problem, I believe him.

We bought Cabrio washer & dryer a year & half ago, and I hate, hate, hate the washing machine. Every load, it goes off balance. And you have to stop your other work, unlock & wait awhile on that, and rearrange your load of clothes. I called the repairman when I first had it, and he said, Oh yeah that happens, nothings wrong. OMG! How I wish I had returned it. If you dont rearrange the load when the cycle is done, your clothes are still soaked. So you have to re-drain & spin. Total waste of money & a lot of my time. Very very dissatisfied and will never buy another Whirlpool product.

Have a warranty with them to get reimbursed for repairs for a year. Have had to use it twice now for the same part. Customer service told me itd take two weeks to get a certified repairman of their choosing to be reimbursed. Two weeks to go without a fridge is their solution and they have no other repairmen working. So I ask to speak to a supervisor and the representative tells me she wont transfer me out because thats the way it is. Paid out of pocket to get it fixed immediately instead of waiting.

We purchased Whirlpool Oasis. The top loader washer and dryer 5 years ago from Sears. Both are scrap now. Paid high end money for these. Tub was changed on washer 2 years after purchased. Now looks like electrical control panel is gone. Oh well, Sears not really the problem because Whirlpool holds the monopoly on appliances. They are made to fail. Watch marketplace or W5 shows the tech men tell the story... You want to get screwed, buy a whirlpool. Hell I did.

Purchased a Whirlpool double oven (WGE745COFH) in September 2018. It is now May 2019. After 5 service technicians verified the erratic temperature fluctuations in the ovens, Whirlpool insists that a +25 degree to -25 degree fluctuation in a heating cycle is normal. The motherboard was changed 3 times, and the sensors were changed 3 times, including hard-wiring the last set of sensors. I called Whirlpool and customer service says that is normal. Ever tried baking at a 350 degree setting that fluctuates from 375 degrees down to 312 degrees while trying to maintain a 350 degree setting? I understand there has to be some fluctuation, but either it took a lot of extra time or burned my food consistently. Ridiculous.So, with the help of wonderful people at Lowes (where I purchased the double oven) Whirlpool is refunding my money and Lowes has taken back the slide-in double oven. In my quest to replace it, multiple appliance sellers have told me that all the new ovens having motherboards and sensors have big fluctuations in the oven heating cycles. I find that unacceptable. My husband and other family members have worked daily in an industry where temperatures were critical. They used ovens that could maintain temperature within 5 degrees of set temperature with analog controls. The home consumers are being ripped off with cheap, sub-standard parts making throw away appliances and getting away with it. What do I buy? Havent figured that out yet, but have purchased a countertop toaster oven that bakes beautifully.

We have put hundreds of dollars in service calls and parts on these items. I bought them because they were supposed to be good choices. NO way! I have replaced motherboard in washer, belt and sensor in dryer, the washer has had mold in it since week one. Ive tried to clean it but just keep coming back. All my clothes smell like mold and I already have lung problems! Cant afford to buy new right now. But last month my dryer started making terrible banging noise and so repairman says I need another part! I bought the part more money! Just to have it quit again! Now the barrel split! I dont think I should have to pay the money I did for this set and surely shouldnt of had to replace so many things that went wrong or put up with the sewer smell from the washer!

Our Whirlpool refrigerator has been an extraordinary kitchen appliance, it may even be 28 years old. The ice maker worked until just four years ago and thats amazing. Its never been serviced and never needed a repair. I dont know what one can say about something thats worked so flawlessly. This seems a little bit trivial when considering the cost of a new appliance, but the plastic veneer on the handle had fallen off and needed glued back on, but thats about it as far as maintenance and repairs go. Overall its been an ideal purchase and I wish wholeheartedly all my purchases were as good as our whirlpool refrigerator.

I have read most of the reviews and it seems like I have ALL those problems with my Whirlpool Cabrio, but I also need to add that there is rust around the bleach dispenser and I DONT use bleach. The inside is also rusted, but its not visible until you take a good look inside because its under the white paint but its all around the inside. So I had to stop using the machine because I now realize what was the cause of the damage done to some of our clothes. We all need to get our money back and have this washing machine picked up and thrown away!!!

Whirlpool Model WDT920SADM0 Dishwasher. We built a new modular home so Abraham Builders ordered all my kitchen appliances in 2014. We did not move in and start using the appliances until June, 2016. Here is what happened during the first 6 months: 1) Would not dissolve dry soap or packets as there were still particles and plastic in the dispenser. 2) Dishes were not getting clean and were spotty. 3) Would not dry dishes, ever!!! 4) Parts would keep popping off as we would find them on the bottom or hanging down. 5) Final straw was this morning around 4 a.m. (12/4/16)... woke up to the smell of wire burning in the house and discovered it was coming from the dishwasher that we had put on delay wash that night and when we opened the door, smoke came out from inside!!Since it was past purchase warranty date, we had no warranty and the builder would not return any of my calls on any problems and the manufacturer of my house closed the factory. Needless to say, we now have to spend another $900+ for another dishwasher! Not happy at all about this Whirlpool model and would not recommend it.

After 25 years my Maytag died. It was a Sunday so we just decided to go to Lowes & purchase a new one. They could not find my 1st choice so I bought the Cabrio. It is the worst washer I could have purchased. It determines the amount of water you need. Our clothes never seem to be clean & its very noisy. It has no agitator & is supposed to save water. Even putting it on the longest cycle our clothes do not appear to be clean.

Why am I not surprised by this stupid American company? I purchased a brand new fridge in June this year and for the last 5 months I have had about 20 different technician visits by five different technicians who changed almost everything you could possibly imagine - evaporator, control, sensor, compressor, display, etc., etc. And the company still refused to take any responsibilities. They kept telling me that more inspection was needed EVEN AFTER all the technicians said there was NOTHING THEY COULD DO. After having to yell at them for about an hour, they finally realized they had to issue me a new fridge. What a piece of crap they are. Even then when I called back about the exchange, they pretended they could not find my file. WTF??? They really tried EVERYTHING they could not to issue an exchange. Wow. What an incredible company and its customer service. I will never, ever buy another American product - nothing complicated with computerized parts anyway. They are NOT capable of producing such complex machines. They should stick with toasters or juicers - lol. Stupid Americans. LG and Samsung all the way baby!!! ** you Whirlpool.

We have just built a new home and have spent a ton of money on appliances. I so wish I had looked up the reviews on this Whirlpool Cabrio Washer before we bought it. It makes a very loud annoying sound through at least a third of the cycle (which I was just told by Whirlpool is the normal agitating sound). We have also had to have service out here twice in the first few months because some of the clothes come out dirty in areas that were folded over because of lack of water even on the high water setting. It also, ripped my favorite white blouse right in half. Trust me DONT buy it, you will be sorry.

This set of washer and dryer are very simplistic and have few options. They came with the house I just purchased and I think they may be 10 or 12 years old. I cant wait to buy a new set... Very soon!!

Whirpool Part #WPW10564292 refrigerator handle - I am a property manager who has 264 units. We have only been open for 1.5 years and have had to replace 30-40 door handles because they crack at the top where screws are. We tried calling Whirlpool Customer Service because obviously this is a defect and she said they looked in the system and didnt see any recall or issues. We also asked for a representative from Whirlpool to stop out so we could show them the issues and she said we have nobody in the area. We have 9 service requests outstanding that need a new refrigerator handle. On July 19th, we ordered 3 handles from our distributor and we were told theyre on back order until September 6th. When I called at the end of August to make sure we were on schedule with delivery, I was informed they are now on back order until November 5th. I just called our part rep. this morning and now they said the current part number does not exists and gave me the new part # W11026870, and they are on back order until mid or end of November. I am not going to keep quiet about this issue. We have paid $79.89 per handle on a refrigerator that is only a 1 to 2 years old appliance. I am requesting a returned call or email on what you are going to be able to do for us. This is not right or fair to a company that spent a large amount of money to have your appliances in 264 units.

I have the Whirlpool Gold microwave model GMH3204XVQ-1 manufactured in May of 2010. The plastic around the lower door handle is cracking (currently in 4 directions from the handle) and the plastic on the side of the control panel is cracking in the center area and lower side. Neither of these area experience abnormal stress in day-to-day use. Unfortunately I could not get a good photo of the other crack on the lower corner of the control panel but included the one on the side in the middle. I contacted Whirlpool customer support about 1-2 months ago and to date, have not received any type of response or concern from them about this issue.

I bought a Cabrio washer in late 2015. All Ive had is trouble with this joke of a product. After three years it wont do any cycle, the people at Whirlpool dont care. Please dont buy any Whirlpool product.

Well, I read most of the complaints with the failures in the machine. I guess most of them didnt last long enough to rate their performance so here we go. I bought a Cabrio top loader, high-E washer a couple of years ago. This one had a different kind of agitator - it was just a couple of inches or so off the bottom. I specifically bought this to wash comforters and it seemed like it was good for that (rousing agreement from the salesperson). So after a couple of years of working with it, here are my observations:Pros: There are absolutely none!Cons: Okay, other than not having control over the settings (cannot override any of the preprogrammed wash settings), it simply doesnt get loads clean (yes, I use expensive HE detergent). Except for the bulky setting, there is never enough water to wash and rinse the loads properly. Next, it makes a mess of the clothes. At the end of the cycle, and this is true no matter what I wash or how large or small the load is or which cycle I pick - even light and slow spin, it just makes a tangled mess of the load. Stuff gets stuck inside of other stuff, wrapped around other stuff or are balled up. Never have I seen this type of issue. I constantly get the unbalanced load notice and have to manually redistribute the clothes most of the time.To address the too little water level, there are two options. I have discovered that the bulky setting has the highest water level, so I use that most of the time. From time to time (when I need different water temps or just want more water), I have developed a work-around by putting a Y adapter on the hot water inlet and a short hose. Once the washer starts the wash cycle, I stop it and add a bit of hot water to bring the level up enough to do a decent wash job - same for the rinse cycle. So much for Whirlpools water efficiency.Next, the hot isnt hot. Its barely lukewarm. So I turn the cold down to a trickle and I get a bit hotter water. It takes forever to rinse though. Its a good thing Im semi-retired. Next is the inflexible cycle/water selector. I have never had a washer I couldnt override to tell it what to do in unusual circumstances. Boy, what rocket scientist at Whirlpool dreamed that up!But above all, this just doesnt get loads clean. I have experimented with all the variables, load size, cycle selection, detergents, etc. Most of the time, I have to do two cycles with my loads and these are not unusual or extremely dirty loads. They are just normal, everyday laundry for an adult couple. Really, Whirlpool! Who was the conceptual designer on this? Thank goodness they werent working on the space shuttle or some disease research.Bottom line, I am so soured on the design and performance of this product that I will never buy another Whirlpool product, either brand name or generic (Sears). I just cant understand how a company would let something like this out the door.

We purchased a $3000 WRF990SLAM00 / K22019120 refrigerator in 2013. Within the first two and a half years we have already put over $700 in repairs. We were told today the coolant for the ice maker has a leak (either a slow leak or a fast leak, they arent sure). But from here on out we will have to put coolant in it to keep the ice maker working. A week ago we spent another $300 to repair the water dispenser. This is the worst fridge we have ever owned. Whirlpool could care less and we are basically out right at $4,000! DONT BUY WHIRLPOOL.

We purchased this Whirlpool pair after our upright machine was unable to be repaired... because of parts coming from China and being hard, if not, impossible to get. We have had this pair for about 2 years now (Lowe’s). It still doesnt clean the clothes and it continually goes off balance when doing sheets, comforters etc. Myself I feel since they have taken the middle agitator out of the machine - it no longer performs the way a washer should and that its main function is to get the clothes clean! I did write a letter to Whirlpool about it and they pretty much told me, “Well too bad.” So much for buying American made products... at least the upright did last 6 years!

I purchased all new, upper end Whirlpool appliances for our newly built home just 6 months ago, to include a side by side refrigerator with ice maker and water dispenser, an over the stove microwave, a smooth cooktop oven/range, a dishwasher, a washing machine and a clothes dryer. We plugged in the new refrigerator, and after 24 hours of letting it sit and get cold, we bought $300.+ of groceries and filled our new refrigerator. We pulled the milk out hours later and it was warm, checked other food items and found them to be warm, too. I placed a thermometer in the refrigerator and it read 55 degrees. In disbelief, I placed a second thermometer in the refrigerator and it, too, read 55 degrees. Being brand new, only hours old, and clearly not working, I called for a replacement refrigerator. Our builder said we needed to call Whirlpool for a replacement. Whirlpool refused to send us a new refrigerator. Needless to say, we had to throw out all of our food for being dangerously off temperature, and we were less than happy about wasting $300.+ on food we could not safely eat, but glad we didnt have food poisoning. Not even the freezer could maintain a temperature below 55 degrees. While waiting on a repairman, we noticed that we were not hearing the refrigerators motor come on more than once every several hours. They sent a repairman out three days later, and he found nothing wrong other than a poorly fitting door, he said. He replaced the door hinge and told us our refrigerator would be cold in 3 - 5 hours. Well, it never did get below 55 degrees, set on the coldest setting. Whirlpool was called again and they couldnt seem to get another repairman out to fix my brand new refrigerator that could not perform its most basic function, which is to maintain food at proper temperature. Again, Whirlpool refused to send me a replacement refrigerator for this clearly defective refrigerator we were stuck with. We were told it would be 2-3 weeks before another repairman could come out, and then he would have to order parts after he diagnosed the refrigerator problem, taking another two weeks. We needed a refrigerator, like most people do, so we were forced to take this brand new refrigerator and stick it in the garage, not being able to sell a brand new refrigerator that wont get cold. Angry at Whirlpool for taking our money and leaving us with a refrigerator that never worked, we bought a Samsung refrigerator that we are very happy with - it works! After 2 months, our Whirlpool above the stove microwave has the motor turn on when we close the door, and it takes several opening and closing sequences to get it to shut off. We will be replacing this new microwave when we can afford to.Our ceramic/smooth top stove/oven, takes a very long time (at least 20 minutes) to preheat and the temperature in the oven is not accurate to the set temperature, according to my oven thermometer. The cooktop surface is inferior; it gets permanent water spots and it scratches very easily even though we use the correct pans and are very careful with it, and does not come clean easily. The surface feels rough, not slick like the GE Profile ceramic/smooth cooktop range that I had for 14 trouble-free years. I am using the same exact pans that I used with our GE, and we know how to be gentle with a smooth cooktop surface. After 14 years of owning the GE stove, the GE felt slick and smooth, cleaned easily, and did not have one single scratch on it. It looked as good as new when we moved, after 14 years of use. I will be replacing this inferior Whirlpool smooth cooktop range as soon as I can afford to, as well. Last month, right before Thanksgiving, our new Whirlpool dishwasher started making a really loud motor sound and quit working that day. It would fill water, drain the water and shut off. I once again called Whirlpool, and they were maddenly unhelpful. This time, they told me they would have a repairman call me in 5 working days to schedule an appointment to come and see my non working dishwasher. After 7 days, I called Whirlpool AGAIN, to ask why someone did not call me for an appointment. I was expecting a house full of people for Thanksgiving and I had no working dishwasher. I spent a lot of money buying these crappy Whirlpool appliances and am very frustrated. This time, Whirlpool told me that they could not find a service person in my area to service the unit. As if I live out in the middle of know-where?! I live 20 minutes from Austin, the state capitol of Texas! A 20 minute drive from the capitol building to my door! Whirlpool told me I could take my 5 month old, broken dishwasher to a repair shop and that the repair shop would need to call Whirlpool before they did any work, and that Whirlpool would only authorize a maximum of $150 to repair my dishwasher. They actually had the nerve to tell me that I would have to pay for the repair, and they would mail me a gift card in 6 - 8 weeks to reimburse me up to $150 on my new, broken dishwasher that is under warranty. I was furious!! Some warranty! The broken dishwasher is now sitting next to the broken refrigerator in my garage. I needed a dishwasher before Thanksgiving dinner, so I went and bought a Samsung.I realize that all makers can have a lemon, but all of my Whirlpool kitchen appliances are junk!! I will never own another Whirlpool product for as long as I live, and I will tell anyone who will listen about our abominable experience with Whirlpools customer service and the expensive, crappy appliances we unfortunately wasted a lot of our money on. Do yourself a huge favor, buy anything but Whirlpool! Thankfully, everything else about our new home has been great. Our new Whirlpool appliances will remain a very sore subject for year to come, I suspect.

I purchased this Cabrio washing machine in December of 2016. I have had a huge amount of trouble with the soap not washing out along with it tangling my clothes. This has to be the worst machine I have ever purchased.

Whirlpool washing machine M# wtw7340xw2 / S# c14270996 - Bought in 11/26/2012. Never was real satisfied with the way the clothes were washed. They never came out real clean and smelled like there was still soap in the clothes. It has been less than two years and now it will not run. Turn the unit on and all it wants to do is turn on the pump to drain the tub. Im a refrigeration technician and know how to run a diagnostic test Whirlpool has for this machine. I get an LF code which is water long fill so I checked out the water tube which is ok. So the problem is in the circuit board not sensing the water level. To replace this board is around $350 dollars and if I had someone else do the work I would be looking at over $550 dollars. I only paid around $500 dollar for the washer so it does not make any sense to put a new solid state board into this washer which cost as much as the washer. Our old GE washer lasted us for over 20 years and did a better job washing our clothes. There should be a better warranty on these machines than one year. I did not buy the extended warranty because of the cost and I expect that the product should last at least 10 years or more.

The microwave keypad is worn down after 10 uses making it difficult to read the pad. I just discovered the microwave was missing the front leg and they do not have a replacement part so I am stuck with a virtually new microwave that will not balance. It took 4 phone calls to their customer service department to try and sort out the problem. Poor product and extremely weak customer service department.

I purchased this Whirlpool washer (model WTW7600XW2) on October 2011. Fabric softener dispenser is full of water at end of cycle. Repairman has replaced parts three times, but the problem is still not corrected. Today, I talked with a Whirlpool supervisor. She says this is normal. She told me to take the cup out and empty it. The cup is not removable, so she said I could blot it out with a cloth or sponge. I paid $800.00 for a washer with an automatic fabric dispenser that I must empty manually. I have used whirlpool appliances for 50 years of marriage, but this is my last one. I am very disappointed with customer service.

We had Lowes install a Whirlpool model Nu40T121-403 natural gas water heater early October 2012. The temp controller went out in October of 2014. I replaced the controller myself at a cost of $30 for overnight UPS from the manufacturer, American Water Heater. The controller went out again almost exactly one year later and I again replaced it for the $30 shipping charge. In both instances the customer service person told me the malfunction was probably due to my not flushing the heater annually, causing a sediment buildup. The water to the heater not only flushed annually, but is filtered through a water softener and there was absolutely no evidence of sediment in the drain water or on the part of the control that is in the tank. Now it has stopped working a third time. I called Lowes about replacing it, but they only carry Whirlpool, so wont be buying a replacement from them.

Purchased a Whirlpool Cabrio Washer a few years back... Started getting F1 error message and just proceeded thru it like most did initially, but now has become pain in the rear just to do one load of laundry as we get the error 2-3 times when we start each load - then on every load w/ 21 minutes left on the cycle. From the looks of things online this is a chronic problem and should be fixed by manufacturer. I called Whirlpool customer service and first person I talked with said they understand it is an issue but no longer are any recalls or reworks on that machine. I asked to speak w/ supervisor and sat on hold until I got one. Was then informed they do know it was a problem but was not something they could do anything about other than schedule a service company to come take a look. I specifically asked if there was at one time a recall or if they were fixing this issue for a while. She said Yes, they took care of some of their customers but are no longer doing that for this model. So basically because I didnt call in at the right time I need to fix my machine myself. I said it will be the last Whirlpool or Whirlpool associated appliance I ever purchase if this is the kind of customer service I can expect... The supervisor just said she was sorry to hear that and to have a nice day. Hopefully enough people read these reviews as I wish I would have before purchasing my Cabrio and dont buy Whirlpool.

When our home burned down, had to get a manufactured home. Orig. refrigerator size was 32 cu.ft. This one that came w/ the house is a lot smaller. Weve has issues with ice dispenser several times in the 18 months weve been here. But I would recommend this size.

The duet washer is just over one year old and started showing F25 code on screen. It had been making a really loud noise in the spin cycle. Last week, a really loud noise and then the loads wouldnt be spun. There was a puddle of water on the floor near the machine. We had a repairman out today and he stated that theyre repairing these machines all the time. He stated it was the bearing and that theyd been told that Whirlpool had installed bad bearing from a different supplier. I called the Whirlpool experience and after 4 minutes and 19 seconds, I actually spoke with a service rep. She said since my machine is less than one month over the one year warranty, Id have to call the extended warranty people. I asked for a supervisor and after 2 minutes and 38 seconds, she came in line and wouldnt budge from her story. They also stated that there are no service issues with this model washer. Extremely poor attitude and Whirlpool is doing everyone, whoever purchased a duet washer, a terrible job on these washers. At least, Ive now found out that there are a lot of other folks out there with the same problem. We need to get some attorneys to start a class action just like the mold/smell customers did already. Sad, sad day for Whirlpool as Id been a customer all my life.

Purchased a Whirlpool top loading washer. The agitation cycle is unreasonably loud. So loud you can hear it everywhere in my home and cannot have a conversation within about 30 feet of it. When I ran it for the first time I thought it was malfunctioning and when I called Whirlpool I thought they would send a technician to fix the problem but they told me that the sound was perfectly normal for high efficiency washers! My other high efficiency washers were very quiet. The fact that they think this type of noise is not only normal but quite acceptable makes me quite certain to never buy any of their products again. Very disappointed to see what once was a quality company to be so lame.

I bought the WP Cabrio washer on 10-18-16 from Lowes. It does not wash well, my dark clothing came out with white spots all over them even after I rewashed them x 3 and the lighter clothing you dont see the spots so you are wearing dirty clothes. Also, it is making a lot of noises while running. WP should pull this model off the market.

Do NOT buy the Whirlpool Cabrio washer...it doesnt actually wash your clothes! Most clothing still half dry after the wash (didnt get any water on them) and they are still smelling sweat after the wash! Also doesnt clean basic stains that others washers clean. Even if you add water manually to the washer to soak your clothes, the clothes on top wont be agitated at all, hence the reason the clothes are still dirty after a wash. Poorly engineered washer... its a lemon as it doesnt do what it is supposed to do (wash clothes). Biggest scam ever from Whirlpool and shouldnt be allowed to be sold to consumers anymore!

Oh what a tangled mess you weave! Inappropriate water usage and bad agitator. The brain is not flexible. Most of all it locks me into a contract of this is it, do or die, you have no other options but to start again. It puts my clothes in abused mode! I say no more, taxes will bring me to buy your competitor. It is very large and way too heavy to move anywhere. No!!! I will never buy another. To the point with all required letters involved, No I will not recommend this (Cabrio washing machine) to anyone, or give it to a friend!

My $800 Whirlpool Cabrio top loader does not rinse the soap out of the clothes. Nor does it even get the clothes completely wet. After the final cycle I have soap scum in all the wrinkles of the clothes. Most dissatisfied purchase I’ve ever made. The one-star rating comes from the pretty blue digital displays. I’ll be purchasing another; this one goes to the dump where it belongs!

I purchased this machine in April 2011. Adequate performance until this past fall. It did not drain properly and began to smell, then stopped working. I called a local certified repairman who discovered an item of clothing trapped beneath the basket blocking the drain pump. $109.00. Less than 2 months later it happened again. The repairman returned and again found a blocked drive shaft under the basket. $109.00. When it happened a third time I called the Whirlpool repair line. A serviceman was sent out and immediately knew what the problem was (prior experience). He removed the basket and once again there was an article of clothing under the basket, blocking the drain pump - $129.00. At this moment it is beginning to smell again. I spent 40 minutes on the phone this morning with Sears and Whirlpool. No help whatsoever. This machine is not even 3 years old. I never overload it and clean it regularly. I bought the washer and dryer as a set because they are quite visible in my home. I have had Whirlpool products for over 40 years and never had a problem. I need someone to stand behind this machine.

We bought our Whirlpool Refrigerator a little over three years ago. Within a few months we started having problems with the unit. From ice maker issues, cooling and freezing. Initially the frig was covered under Whirlpools 1 year warranty. Then our extended 3 year warranty kicked in through HH Gregg which they supplied for free because of their poor handling of the initial sale. We have lost track in how many times a repair man has come out to work on the refrigerator. In the last year alone its been at least 8 times. The most recent problem had been the freezer not defrosting properly to the point where we had to store food in our neighbors freezer. The repairman has tried everything he knows and is stumped. Well our extended warranty has run out but theyll continue to work on the problem as long as we report the issue within 30 days which creates a whole different set of issues. The extended warranty states they will replace the refrigerator if it has the same problem 3 times. However what they dont tell you is that if you call BEFORE 3 time period its considered a recall and that doesnt count towards the 3 strike rule. We contacted Whirlpool and they wont cover the refrigerator because the repair company isnt on their approved list. Really a Sears repairman isnt approved? So buyer beware of a lemon Whirlpool Frig! They seem to have a way of not covering their product.

The washer never uses enough water ever. The clothes are not clean and it sucks! The clothes are half dry when agitation is going. The bulky setting doesnt clean the clothes either. Ive tried every detergent on the market to see if it would help. No different results. I paid a lot of money in 2015 for this washer and Ive had bad experiences ever since. No change in my water bill since I have to usually wash clothes and towels twice. I want my money back so I can buy a better washer! Im beyond aggravated! I have looked for my receipt but its been awhile. I did get insurance on it. I bought it at Lowes it should be on my card they scan.

We bought a Whirlpool side by side refrigerator new. When the first one was delivered it had electronic problems. We sent that one back. The next one, same model, seemed to be alright for a few days then it developed electronic problems. My son discovered the problem was caused by a faulty door panel in the freezer. The panel would come loose and if you knocked it back in place the electronics would work until the panel came loose again. Whirlpool would do nothing about our complaint. Now the refrigerator section freezes things. We paid to have it fixed 2 months ago and now have the problem again. The repairman said he had brought up concerns in meetings about the same door problems and been blown off. Our food is freezing in the refrigerator again and Whirlpool has blown us off again. We will never buy Whirlpool again. I trusted Consumers Report when I bought the Whirlpool and that goes to show you that doesnt always work either.

Whirlpool Cabrio Washer WTW7340XW sounds like a small jet during spin cycle. The Whirlpool Cabrio Washers have a very well known and well documented problem with the tub bearings failing. Many many disgruntled owners have posted their complaints online, and there are many videos showing the issue on youtube. This issue is so prevalent that the manufacturer has created a tub bearing failure repair kit for $350. The repair is so expensive and labor intensive that many of the certified Whirlpool repair shops no longer work on the Cabrio washer stating that a better washer can be purchased for the cost of this repair.That said, the manufacturers customer service group denies that the Cabrio tub bearing failures is a common problem and are quick to state that Whirlpool holds no liability for this problem. Ramping the complaint up to a customer service supervisor is met with the same canned response. Regardless of the thousands of complaints Whirlpool is claiming that it is normal wear and tear for the tub bearings to fail. The manufacturer should recall the units for this manufacturing defect in the Cabrio design.

I have purchased many Whirlpool ranges for my apartment buildings that I own and operate. They never give me a problem with operation or length of service. I only have to replace them when a tenant does something dastardly to them. My husband and I remodeled our kitchen and we purchased one for our kitchen too!

Model ED5PVEXWS14/Whirlpool Stainless Steel side-by-side refrigerator purchased from Lowes: My wife and I purchased this refrigerator from Lowes as a part of a kitchen renovation project. It was delivered by Lowes and worked great. The shelving cracked at the back as other owners experienced, but I blamed that on kids and was fine with ordering replacement parts online. Fast forward to the present and a year later, everything is working fine. Out of the blue it quit cooling or freezing on 6/12/13. I thought it was a capacitor problem, but since we purchased the refrigerator on 4/28/12, we decided to have a repairman come out and check. When he accessed it, he found that the compressor was bad. He stated every once in while you get a fridge with a bad compressor. He also said I just happened to have the particular refrigerator he sees frequently. I normally buy all Whirlpool products - microwaves, washer and dryer, dishwasher, my old refrigerator (still working at my relatives house), and my daughters college fridge. This is the first time I have experienced something of this nature with a Whirlpool product and hope I can work out a resolution with them or Lowes.

Ive never considered writing a complaint before, but feel it is necessary in this situation. I have had my Whirlpool refrigerator since November, 2007. It has worked great until this past April when the freezer began to overfreeze, cause frost and ice to build up. I have had Whirlpool Factory Service out to repair the unit twice a month since April with still no resolution and the appointments are getting harder and harder to get someone to come out in a timely fashion. I called on September 1st and the closet appointment is September 15th. They werent even able to book the appointment when I called. I was told someone would call back within 3/4 days. When I didnt hear back today, I called to find out an appointment was set.Ive called the Resolution Team to obtain back records of service but havent been successful in receiving a phone call or email. I havent received all of the follow up emails after service which is frustrating since there have been two technicians that have come out for repair and were not provided any history on the unit. If I had the follow up emails, I would be able to share that information with them.I contacted Customer Service to find out what I can do in regards to the issue I am having and was told its best to stay with the service provider that I began with since they are familiar with the issue. I would imagine if they are familiar with the issue that it should have been fixed by now. Ive also sent a response card back to Whirlpool Home Appliances at the Survey Response Center and havent heard anything from them either. When I called to follow up there wasnt anyone that could point me in the right direction to obtain answers. They were able to provide me with the mailing address for Consumer Affairs though. Ive been told numerous times that if it gets to a point it costs too much to fix they will replace the unit. Im not sure when that decision is made. I have an extended contract and will extend it again in October when it expires. I just want the unit fixed or replaced. Its been since April with the same issue. Very disappointed consumer.

I purchased a washing centre at Canadian Appliance Source. I paid to have it delivered, installed and for them to take away my old appliances. I had several issues and when I called the store, they sent me to Whirlpool warranty who dispatched a repair technician a few days later. With nothing solved to my satisfaction, I called Whirlpool again. I spoke to a customer service rep who gave these responses, she put me through to a manager who gave me the same responses. When I asked to speak with someone above her, she said she could put me through to another person at her level but noone at a higher level.I want to hear the same response again? Really? Her only other answer was to email the Whirlpool Executive, which will be my next step. This is a summary only of my experience of the first few days after the purchase.Problem: The first load I washed was 1 set of blue sheets with 2 pillow cases. The water didnt seem to cover the load but I thought when it started to wash, they would get wet. When I took the sheets out of the washer, there were several dry spots and some kind of residue on several areas, so not washed or cleaned as expected. I tried washing one sheet, same thing. Tech solution: Put in some wet items to the load so the washer thinks the load is heavier and will add more water, or add a bucket of water to the load, Really? Whirlpool response: The washer is working as expected. Really? Problem: I did a warm water wash, expecting the machine to dispense a mix of hot and cold AT THE SAME TIME making it warm water. The washer starts with cold water then stops and puts in hot water. I dont want cold water or hot water on this load I want warm as recommended by the manufacturer! Tech solution:Dont use warm water wash. Really? Whirlpool response: Works as expected. Really?Problem: Dryer is way too hot on the delicate cycle, not good for delicates! Tech solution: Use the air dry cycle. Really? Whirlpool response: Dryer is working as expected. Really?Problems I didnt even discuss: The load is really really wrinkled when it comes out of the washer. Who wants to have to go back to ironing everything they own? The washer tub and dryer are really really small! I should have read more reviews and headed the warnings! Comments: I purchased online, biggest mistake. The store will not take it back. Whirlpool will not take it back. Hindsight is 2020! If I could have given negative stars, I would have.

I purchased a Whirlpool Washing Machine in November, 2015 and today, I had a repair person out who said the bearing had ruptured and the washing machine cannot be repaired - 2 1/2 years later. Contacted Whirlpool Customer Service who would do nothing other than try to explain to me that I should have purchased an extended warranty as they could not stand behind the machine past the one year. Would not even offer sending a tech out on their dime to confirm what my repairman had said that this is a failed production process of these machines - it was nothing that I had done caused this issue. But yet they wanted to sell me another machine. It will be a cold day before I purchase another Whirlpool product.I was shocked at the lack of customer service to assist with a situation that both the location I purchased it from and my own repair tech said that they are seeing so often with these machines. I would never purchase another item from Whirlpool again nor would I recommend any of their items. I will go to great lengths to give others the background on how Whirlpool will not stand behind their products, lack of customer service to resolve a situation or can work outside of what is given to them to correct a situation - this is not OK!

I bought 40 gallon gas water heater in June 2004 and had to have it worked on twice, costing more than I paid for it. I am replacing it now because pilot light will not stay on, and it is currently out of warranty, and I have no faith that simple repair will hold more than 1 year stint. Customer service was attentive but product itself failed to meet expectations.

DOES NOT MEET CONSUMER NEEDS AS PROMISED. I wish I read the reviews. Very expensive machine I purchased specifically for the large drum for large loads. The machine cannot handle large loads (if you consider one blanket large load). I have to unplug the machine mid wash, as the load gets stuck on one side and moves my machine across the floor. The noise in the spin cycle with even small amount of laundry sounds like a helicopter is about to land. Then last night I noticed black oil splattered all over my floor. This is a $800.00 machine. Never ever met my exceptions as the machine promised to deliver. Theres very little water that enters the drum... Not even my towels come out clean. DO NOT BUY WHIRLPOOL... EVER EVER EVER.

My hot water tank wont stay lit. I replaced the heating element, and the thermo couple. It will light up now but it only stays on for about 10 minutes.

Bought a Whirlpool dishwasher and just over a year later all the wheels fell off the bottom rack. Called to get replacements and it was going to cost me over $200. I paid $800 for the whole machine. I would NOT recommend Whirlpool. I have now heard of other people having the same issue. Very disappointed. Will probably buy a new dishwasher as it will probably happen again with the replacement wheels.

I purchased a Whirlpool dishwasher and refrigerator/freezer from Home Depot. Within weeks the stainless steel on both products began rusting. They sent a third party repair service to look at both products and determined that, in fact, the stainless steel was rusting. Our technician said that both the dishwasher panes and the freezer doors would be ordered and replaced the following week. This was on September 4, 2015. After several promised arrival dates, the parts never arrived. I called both the third party repair company and Whirlpool on several occasions only to be told they were on back order. Finally, in late November, the new dishwasher panel arrived and was installed. It is now December 17, 2015 and our freezer door is still on back order. When asked what my options are, the Whirlpool representative simply said we have to wait. I said that because I have been so terribly inconvenienced that they should just come and pick up this piece of junk and replace it with a new one. Evidently, that is not an option. I will NEVER purchase a Whirlpool product again as they do not back their warranty. I now have a $2,000 rusted refrigerator freezer to adorn our beautiful Christmas kitchen. Thanks, Whirlpool. Youve certainly made this a Merry Christmas. (Yes, sarcasm in play.)

I purchased a Whirlpool cook ceramic cook top for our new kitchen. The very first time I made something (it was lentil soup) something stuck to the cook top. I have had a ceramic cook top before for 18 years - never had a problem until the whirlpool cook top. I cannot get it clean. I have tried everything! Such as stove top cleaner designed for whirlpool cook tops ($22), other cook top cleaners, the single edged razor, a scrubby sponge, steel wool, I even resorted to furniture stripper - NOTHING has removed this spot. I am ready to throw out this new stove top! What a huge disappointment this Whirlpool product is.

Whirlpool Duet Steam Front Loading Washer Model #WFW9750WW01 - The washer is only 5 years old and sounds like the space shuttle landing while in the spin cycle. Cost to repair parts only will be $896.87. The bearings among other parts are shot. I will NEVER own another Whirlpool appliance under any circumstance. Angry is putting it lightly!!!

I have a Cabrio washing machine and the circuit board has gone bad. I understand from Whirlpools customer service that if your machine was made before 2005, they are fixing the issue. Mine was made after 2006. Even though the problem is the same, Whirlpool will not correct the problem. I was told it was fixed in the new machines. The circuit board goes bad and you have to start and stop the machine at least three times before it will start your cycle, then it stops again at the 17 minute mark and you have to cancel and start the machine again for it to finish its cycle. The error is F1. Customer service acknowledged that this is a known problem for the Whirlpool machines built before 2005 but deny any claim that is is happening to the machines after 2005. Looking at all the other complaints, it is still a problem. I am disappointed in Whirlpool for their customer service attitude and for them not standing behind their product and fixing a known problem. I have always bought Whirlpool products but going forward will be switching to a better company. Shame on you Whirlpool. For a machine I spent $1000 on, the part is going to cost $300 to fix.

I purchased a Whirlpool French door fridge 6 years ago. In less than a year, it was not cooling and I was able to retroactively purchase an extended warranty which ended up saving me a ton. Less than 3 years later it had broken 3 times with three different part problems with a total down time of 6 months. Despite saying it didn’t qualify for lemon law, I was able to get it replaced after presenting all the facts. 3 years later, the new one is now currently experiencing the same problem and running a toasty 58 degrees and my food is once again in coolers on ice. Shopping for a different brand and I recommend you do as well. Whirlpool used to be a brand you could rely on. No more.

I have a roughly 2-year-old 30 Whirlpool electric range that has just got out of warranty 4 or 5 months ago. It has been a great stove up until the last couple of months. We have had 4 incidents where the burner would shoot up to high on its own even with the knob down at medium or low. 4 times in the last month, it has come close to catching fire while we were cooking. I have contacted Whirlpool about this issue and have yet to get a response.

The problem started with an error code F3F1 on dryer. Called A & E Factory Service who is company that are certified Whirlpool technicians. They have been out 7 times, March 26, April 1, April 8, April 13, April 27, May 5 and May 12. During those times they ordered and replaced the main control board 3 times and a thermistor for which we paid for parts and labor. The company now says they think we have a lemon and we are supposed to hear back within 48 hours whether we are going to be refunded a total of $504.48 we have advanced for repairs less the service call. They referred us back to Whirlpool and said they would no longer come out as the dryer cannot be repaired! Talked to Whirlpool customer service that says we didnt have an extended warranty and there is nothing they can or will do. This dryer was purchased on 12/31/11. They took the position that because there is no recall for defective parts for this model, there is nothing they will do. Attached is our purchase receipt and all service invoices regarding this matter.

My husband and I purchased a Whirlpool over the range microwave in 2005, model number MIX155XHPT-1 and serial number TR S 30 32419. At first the top vent broke then the opening side broke off. Then the whole side of the closing door broke off. Now the whole door wants to fall off. I would have never expected this from Whirlpool, but it happened.

I initially purchased all new Whirlpool products as part of my new home purchase in a Pulte subdivision, June, 2011. My WP microwave failed to heat in 2012 and the replacement of the Magnetron and Inverter and service was covered under warranty (would have cost me $493.51). Sadly, the microwave again failed to heat in 2014. I was so disgusted with this second failure, I decided to live without a MW until January, 2016 when I paid for my second service call and learned, once again, I needed a replacement Magnetron and Inverter, to the tune of $400. Both servicemen told me the 2011 magnetron/ inverter mechanisms were new technology and did not last long. Again, sadly, when I contacted Whirlpool, they would not admit to their defective product line and indicated they could do nothing since I am out of warranty. It is unconscionable that a corporation is not liable for their defective products.

My old Whirlpool stopped working so I purchased a new one 2 weeks ago. I have had 3 items ruined since using this machine. It is leaving blotchy spots on the clothes and they will not come out. I do not use bleach but the spots look like bleached spots or stains. After reading other reviews I would like to know what the manufacturers are going to do. It is not very economical if we have to rewash everything or replace clothes the new washers are ruining. I have just spent hundreds of dollars for something that does not do its job and would like to know what the solution is. Is there a model washing Machine out there that still cleans clothes? Since mine is only 2 weeks old can I trade it in (Lowes)?

My model - GB9FHDXWD06 - is one of only a very few that fits our space. However, it has failed three times in 5 years: 1) A faulty defrost drain tube that was replaced under warranty, 2) A jammed vent flap that caused the freezer to fail, and 3) a burned-out control panel (an expensive repair). It is also annoyingly noisy and middling at energy efficiency. The coils are in a very narrow space below the refrigerator, which makes them a bear to clean. And, the plastic front plate that must be removed for cleaning breaks far too easily.On the good side, it is a bottom freezer model (which is far better for convenience), the space-wasting ice maker was very easy to remove, the glass shelves, removable baskets, and drawers are easy to clean, and the auto-defrost works very well (after the recall update, number one, above). Temperature uniformity is good and the freezer maintains below 0° very well. Overall, it is a good looking appliance with mediocre efficiency and poor reliability. Not recommended.

I join the many who have posted about the Whirlpool Cabrio Washer cracked lid issue. Our Whirlpool Cabrio WTW7800XW2 glass-lid washer suffered the same (inevitable) fate – cracked plastic on the lid at the hinge stress points, after the washer was beyond warranty. Same story - runaround/no help from Whirlpool. Finally bit the bullet and shelled out the $200 for a new lid. HOWEVER, I didnt want to just replace it and have the same issue down the road. I removed the spring-loaded units that support the hinges, hoping to just remove the springs to release the pressure. I found that the springs are integral to holding all the components together in this unit. These are extremely heavy-duty extension springs, so I took them to my hardware store (TrueValue) and found springs the exact same length, but with a smaller wire diameter and thus requiring less force to extend. I replaced the original springs with these (Century Spring Corp. - #C-143 - 9/16”x3”x.054”). The lid operates perfectly, and now there is very little resistance at the hinge stress point. The only difference is there is no longer a “damping” effect when lowering the lid - it must be lowered manually rather than being allowed to fall on its own. That’s a small correction in habit, but will ensure that the replacement lid lasts for the life of the washer.

We bought this washer from Sears with big hope. Within the first year, we had 14 service call covered by the warranty but required 2 to 3 weeks in doing without. Whirlpool replaced the washer at no charge but continued to have various issues over the years. The new one is the control module that Whirlpool knew was faulty but did not let their customers know. The control module went over the weekend but I repaired it myself and do not have any more issues. I literally went in and tightened all of the hardware, removed and install the pulleys, motors pumps and replaced a lot of keep components with better quality. Guess that year the CEO made only 20 million rather than 19 million. Being an American company I was disappointed by the consumer relations people but everything is a throw away nowadays. Will not buy a Maytag or Whirlpool product again. Where has American product pride gone?

We purchased the Whirlpool Cabrio washer & dryer. The glass lid design is VERY POORLY constructed and should be replaced by Whirlpool. We paid over $200 the first time the lid broke and was told this is going to be a continuing problem. They were correct! We subsequently replaced the lid 2 additional times only to have the same break on the right hand side causing the lid to pop up. Something must be done and WHIRLPOOL need to care for their machinery. They should replace the lids or provide a major incentive for consumers to replace the washer. PLEASE DO SOMETHING!

We purchased 2 whirlpool commercial coin operated washer machines and both computer boards had to be replaced twice each - model CAE2743bqo and CAE27438qd.

The washer itself doesnt get the clothes clean. The clothes on top never get clean, they smell. It doesnt spin out the clothes evenly even though I put them in evenly. There is oil on my floor under the washer and Rent-A-Center doesnt care and its under their Benefits plus program. They were to send off both washer and dryer last time and had no paperwork where washer was sent off at all. It has ruined a lot of my clothes with spots and I used the Tide pods. Stopped using them cause they were not working. I will never buy another Whirlpool product or appliance. Water pump went out in one year... Why would you not care about your customers... I got this set in 2013 and its the Platinum line triple top loader. You lucky to do one load at a time, a single load that is...

Most awful oven I have ever owned!! I purchased a brand new Whirlpool double oven one year ago. I was replacing a Whirlpool double oven, and all my other kitchen appliances are Whirlpool. It is model #WOD51EC0HB01. WORST DECISION EVER!!!! No more Whirlpool for me!

The machine was great and handled large amounts of laundry. It was very expensive but my wife was happy with its performance. A year and a half into owning it, the electrical code F70 comes up and it stopped working. When I checked online, I found it is a common problem. I contacted whirlpool customer service and they could not do anything. Spoke to the manager, Kiesha and she refused to help me even though I bought both the washer and dryer for a lot of money. Customer service is not a priority evidently. She denies that there is an on-going problem when both the internet and my service tech say differently.

I apparently am one of the lucky ones to have an electric water heater. My unit started giving me failure codes during the Christmas holidays. Each time it would fail, I would get a different failure code indicating the upper element, the lower element, and a sensor failure. After testing all 3 of these components, it was determined to be a controller issue. After speaking with Chris on the phone, he overnighted a new controller to me. I installed the new controller and had no more failures. Hot showers for New Years! Thank you Chris.

Piece of crap. We built home 2 years ago and have all gold series appliances! They are all CRAP. Wish we would’ve upgraded to KitchenAid. Dishwasher won’t wash, microwave has hot spots and has to be unplugged and plugged back in often to work. Freezer side of the refrigerator will stop making ice because it freezes up often! NEVER buy Whirlpool!