I purchased the Energy Smart Gas Water Heater about a year and a half ago, intending to install right away as part of our upgrades. Just now, I was able to install this replacement to our 30-year-old water heater that was showing problems. When trying to start the unit, I kept getting the response that the lower sensor unit failed. We contacted plumbing companies. We were told they would not work on any Whirlpool models purchased from Lowe’s, because they were the worst hot water heater ever made. I called Whirlpool support. They wouldnt put me through to a tech support person until I was registered in the system. I gave up trying after many minutes of frustration.

I bought an Accubake gas range. I had Whirlpool replace the top sheet metal as it was bowed, cheap & thin. A few days later, they replaced all the brass burner orifices and it all froze and would not turn off. I had to pull the range away from the wall and turn the gas off. The bottom door to the broiler is wide open and it will not close. The stop button for the oven also does not work. This company has been selling these lousy products based on their previous good reputation.

Bought brand new stove, had issues from day 1, called them after TWO different repair companies came looked at it and said it was a melon, Whirlpool wanted to send a third repair company. Started dealing with this in September, its now end of December and Im still waiting for replacement stove.

We bought a gas Whirlpool Stove from Lowes. We noticed it was not heating like our last stove and thought maybe because it was new. No the stove does not heat properly at all. I cooked a pork loin for 40 minutes at 350 and it was still raw in the middle. I have had to cook everything on 375 which makes the door handles and knobs very hot. I called Lowes and they patched me into Whirlpool after a 45 minute wait. The rep from Whirlpool said, you can look at the manual and figure out how to calibrate it. No I cant. I have a warranty that is what it is suppose to cover. Then I was on hold for another 20 minutes. Really no one should tell you to read a manual to fix a gas stove. I will not buy another Whirlpool item. Poor customer service and that make you feel you are bothering them.

I have had a lot of washing machines in my life and trusted that Whirlpool would have good products. Well, with this top-loader, I couldnt be more wrong! I have never had a machine that just sloshes clothes around - at best - leaving them just as dirty! Our water bill has greatly increased on top of that - I AM SO VERY DISAPPOINTED! Unfortunately I cant return the bad merchandise since I bought at a Scratch and Dent store (just a dent on the outside does not interfere with performance...).

Whirlpool gold series refrigerator - We obtained this appliance in 2013. The ice maker stopped making ice. Later on it began to make super loud popping noises. Stops cooling, doors are rusting, drawers are broken. We do not have extra money for costly repairs. The Whirlpool brand was worth $2500 and the letdown priceless. Do your homework before purchasing a Whirlpool!!

Purchased a Jenn-Air single wall oven model JJW2427WS after seeing it displayed in an appliance store. Oven was installed as directed. Upon viewing the panel, I discovered that it does not light up. You cannot read the function or numbers, never mind start and cancel without a flashlight. I have been a Jenn-Air customer for over 20 years. This is the first time I have been disappointed. Also, has this model been discontinued or recalled?I wrote to the CEO of Whirlpool and explained my problem. I was told that this is not a functional problem, but perhaps a design dissatisfaction. I cannot believe that there are other consumers who are not having difficulty using their appliance without additional lighting in their kitchens.

I bought the top-of-the-line Whirlpool top-loading washer and havent regretted it for a minute. This machine washes everything from the most delicate to the most bulky and heavy and does an excellent job of it. It saves about 1/3 of the water my rotary agitator washer used. What more could I ask from a washer. Incidentally, also purchased the largest front-loading electric dryer Whirlpool makes and never have to hold a load of wash until the dryer finishes the last load...a real time-saver.

Purchased heavy duty dual steam washer and dryer in 2008. Recently got some error codes that we could not fix. Had one service company come in and they could not figure it out. Had a certified Whirlpool company come in and they could not figure it out. They called Whirlpool technicians and they were even unsure of what is wrong. Said they could keep ordering parts and trying them to fix the problem. And of course I would be responsible for the parts. And no guarantee it would be solve the problem. Called Whirlpool direct, to no satisfaction. They said they could send the same company out and have them call the tech line while on site and try to troubleshoot the problem. However, would have to wait another 3 days to get him out. Been a week without washer. I have had washers bought previously last over 10 years without any problems. If these machines are breaking or control boards are going out after about 4 years, then Whirlpool has a bigger problem. Whirlpool supervisor was only offering to maybe a discount on the parts needed, without even knowing if they could fix the problem. Seems to me like they really dont care. Very dissatisfied, will definitely not recommend this product to anyone. And if it ever gets fixed, I am going to sell them immediately.

I purchased Whirlpool dishwasher, model DU930PWSTO, in 9/2007. It quit working in 5/2012. I expected an appliance made by a reputable manufacturer (Whirlpool) to last longer than five years. It seems like a manufacturing racket where they build these things only to be replaced a short time later. With service calls and parts replacement, its cheaper to buy a new unit. Talk about a circle jerk! And who the heck puts anything else but SS screws in a water soaked appliance? Duh. Rust! Im disgusted and dissatisfied with the whole company. Im still waiting on their response to my complaint email; at the time, the machine quit working. Whatever happened to pride in American made products? Or, did this get company bail and were now slaves to the Chinese junk once again? Ill never buy another Whirlpool appliance again. Does anyone have anything good to say about this company? I wish I would have read this blog before purchase.

The first thing I noticed after purchasing this stove was that the glass top did not clean properly. I used the product given to me by Sears and tried several others but still could not take marks off of the glass top. I never really used the oven that much until retired and started baking often. The self clean does not work at all unless by self clean they mean that you yourself cleans -- I should say scrub it down. I previously had a regular self clean and it truly self cleaned. All I did was take wet paper towel and wipe out. Yet when I asked the Sears saleswoman about how it cleans I was told that it was terrific -- I would not have any problems! What a laugh!

Buyers beware! I have had the Cabrio top loader washing machine for less than 18 months and it is already giving me problems. During the wash cycle, it sounds as though the gears are grinding to the point it wakes my family up two floors up! The spin cycle is a joke. The washer sounds as though it is going to spin off into another room! When I called Whirlpool, they told me to shut the circuit breaker. That might reset the computer. No go which I figured as much. I have had washers that lasted 10 plus years with no problems. It is not worth your time or your money. Never again, Whirlpool!

I have a Whirlpool built-in double oven. It is 7 years old. The top oven has overheated 3 times with food in it and it locks the door. The oven beeps and says, Too hot, and locks the door. Luckily I was in the kitchen when it overheated, so I could turn the oven off. After turning the oven off, the oven has to cool off before the door will unlock and the food can be taken out. By then, the food is really burnt.I called Whirlpool to see if there is a recall and they said, No recall, and the oven was out of warranty. So I called the repair shop. They said it was the control board and they were not sure they could get a new control board. I may have to find someone that can rebuild this control board. They said not to use the oven. It could cause a fire. I would think that they should recall these ovens. They should have a safety switch that shuts the oven off if it overheats like mine has done.

We purchased a gas range (Whirlpool AccuBake model # mfgxfg361lvt1 serial ry1810956) a few years ago and have been very unhappy with the gray grids that it came with. We wrote to you about how we should clean them and you recommended heavy-duty degreaser, pin31552a and gas grate & grill cleaner, pin3167a, which we purchased. Neither worked, even with heavy elbow grease. We are very upset. We have purchased Whirlpool products all of our life and would like an answer or some type of explanation. If possible, can we get the grids in black? We try our best to keep these things clean and this is a very bad patten.

Good microwave and will have 1100 watts Of use for TV dinners and warm up food. Do well and goes well. Please use this as well to warm up TV dinners smaller than most. Test them and see what is best. Go.

I purchased our brand new double ovens on 9/27/11. I was happy until 11/3/11 when the inside glass exploded, shooting shards of it all over our kitchen during the self-cleaning cycle. I immediately called Kitchen Aides corporate office in Michigan. She said that she could send a technician out to access the damages but didnt see that this was a product issue. Like I dont know how to properly push buttons to self clean! The technician came out the next day and said that he was only authorized to replace the glass, nothing else. He couldnt tell me why it shattered, he thought perhaps there was a bubble in the glass during manufacturing. I said I think it needs a whole new door at the very least, but more likely a new unit. I just paid $3000 for what will be a refurbished oven after one month of use. Today, I called once again to tell them that I am not satisfied with new glass, not to mention my oven is unusable in its current state and still has glass sipping out. I spoke to a woman in their safety committee department, who told me that Whirlpools warranty is replacement of broken parts, nothing more, and since only one pane of glass broke and not the door physically, they couldnt authorize a new door or new oven. Mind you, that we still dont know why it broke, was it just faulty glass or could it be a heating problem? She didnt care, only that they could only repair the glass. I asked if the glass could be overnighted since I have been without an oven for four days now. She said that she had no way of doing that, so I asked if I could speak to the parts department and she said I could not, that only techs could contact them. I asked if she could do anything for me? Could she assure me that it would be fixed within the week? No. Could she assure me that it would be fixed by Thanksgiving? No. Whirlpools policy clearly is that once you purchase their products, they have no intentions of listening to their customers complaints or concerns only to do the very minimum required.

My wife and I purchased a Whirlpool Cabrio washer 1 year and 4 months ago. Its just three of us in the house. We never overload the washer. Now the drum bearings in the washer have gone bad. I feel that a washer should last longer than 1 year and 4 months. I signed up for the Whirlpool Repair Plus 1 Service Plan which is supposed to cover repair plus 1 year additional warranty. I was told that it would cost more than $1000 to repair so they would only return service plan cost. Whirlpool used to have a dependable product and dependable service. I dont think I will be buying another Whirlpool.

I bought a Whirlpool water heater not even 3 years ago, and I am already replacing parts; thermostat,thermocouple, and as of yet, no fix. We contacted Whirlpool, and they said that everything has been tried, and if the thermocouple doesnt fix it, well have to hire a plumber at our expense. Its kinda ridiculous. The water heater that we replaced, had been in the home for almost 17 years.This one didnt even make it to 4.

If it were not for the fact that this refrigerator has a defect that Whirlpool has recognized and is replacing the unit for, I would give the unit 5 stars in all areas. I would buy another Whirlpool due largely to the companys willingness to recognize a problem and promptly take corrective action.

I purchased my Whirlpool gas range about 5 yrs ago as brand new. Two and a half years after purchase, I started getting the F2 error and always had to pull the breaker to stop the oven. Whirlpool would not do a thing, they wouldnt even listen to me. So I bought a new control panel. Now once again here it is the holidays and Ive started getting the F2 error when I try to use the oven. So needless to say this is my last Whirlpool appliance. And the Service Officer wont even listen to me when I say I have to buy a new oven.

Sent an e-mail to Whirlpool. They responded with apology. Sent a second e-mail telling them they should be paying the $300 for circuit board in a two-year-old range. No response. Also, sent e-mail to Geniers. No response. The impression I get is that neither are the least bit interested in the problem. Once they sold the $1260 range, they were done. We will never buy another Whirlpool from any store and we wont buy anything from Geniers in the future.

I purchase a WP Fridge only unit model WRF578 18D MOO in July 2016. I woke up 3 months later and my fridge was filled with rotten food, the internal temp was 16 C 60.8 F. I phoned Sears and they had me phone WP. They tried to repairman but he phoned and told me that he could not service my fridge as he was a 3 1/2 hr and one Ferry ride away from me - He was in Whistler and I live on the Sunshine Coast. I phoned WP again and they sent someone who actually lives here. He found and repaired a small freon leak. Four months later it happened again, the fridge was also making loud noises when the compressor started and stopped. I phoned WP again. They sent the same repairman, he ordered and installed a new compressor and topped up the freon. Sadly less than 3 months later it happened again. This time I was very firm with WP that I was unhappy, they extended my warranty for a further 6 months. The same repairman again came and topped up the freon. That brings us to this week. On Wednesday June 14 I woke up again for the fourth time to a fridge full of rotting food. The fridge was actually warmer than my Greenhouse that day! I phoned WP. They were unwilling to help so I asked for a supervisor. She offered to pay 1/2 of the service call as my warranty had expired Jan 26/17. I said that was unacceptable and asked to speak to her Supervisor. She stated that she was as high as I could speak to, so I asked for an e-mail address for her supervisor. She instead tried to tell that I had no warranty and that they had already fixed my fridge 3 times and given me an extra 6 months on my warranty and offered for me to BUY an extended warranty! I replied that if my fridge were fixed I would not need a service call and that in fact my fridge had never really been fixed. She transferred me to another person. He offered to pay for the service call. I accepted. He asked if I were happy, I said that I would wait and see after the service call on Monday. I Asked if it were the same Man, he said that violated his Privacy. I said I will see him Monday! Will he be wearing a disguise?! Kohuch (the Service guy is coming over this afternoon -Friday) my Husband left work early to be here.

Whirpool has its main washers, then the off brand of Whirlpool. After using the washer after a few months the balance starts to get off balance. Trying to find parts and get them put in is easy, hard part is replacing them after they wear off after use a few months.

We bought a Whirlpool Cabrio 6300 washer based off the salesmans recommendation (not very happy about this). After the warranty ran out, every time in the spin cycle, it makes a sound similar to a piece of metal banging around inside the cylinder during the cycle. Our friends have told us they had a similar experience and for their machine, they found out the bearings were going out. Weve had this machine a total of 3 years. I doubt we ever buy another item from HH Gregg plus will do our investigation on Consumer Buyers digest before we toss any more money out for a washing machine.

I owned a Maytag washer for 30 wonderful years, so I of course bought a new one. I have battled with my Maytag (Whirlpool) front loading stackable top of the line washing machine for 2 1/2 years. It will not drain, yet sometimes it will. I have played every game with this machine to figure why. I had a repair company out 5 times while it was under warranty and they could never find the problem. It is totally unpredictable. If I could bill Whirlpool for my time and anguish I would own this company!They now say it is the computer board and I will have to pay $350 for a new service contract to fix the machine. I not very politely said that they should pay me for all my emotional abuse. They offered me another option saying they would pay for a service company to come out and look again. However, I would have to pay the labor and material cost. Since I have a stackable unit and it would take 2 technicians I would have to pay $90 for the second person. I was so mad that I called Whirlpool back and they refused to offer me that $350 charge and just said sorry. I are fortunate to have a lake house which needs a new washer. Guess what? It will NOT be a Whirlpool product. I wish I could go to the store where I purchased this holy terror and picket!

After 2 years it stopped draining. We have to physically hit cancel to get it to drain. Also, I have had to make my own tool to take bottom spin bar off to get to and unjam grinder and we pre-wash all dishes.

Size was greatest consideration, then cost. Next was power consumption. Quality claims were of no value, since ALL are made in China/Korea. Korean made would be a better choice than China. Am satisfied, but not greatly, as refrig. bottom freezer died a few days out of warranty. YouTube video had my exact refrig. so fixed it myself. Bottom freezer drawer keeps coming off its slides, but I live with it. Top refrig. section freezes things on top shelf, but 2 and 3 shelves down, temp is 39 to 42 = cannot get even temp. As a former inspector, I know about air circulation, crowding.

I am extremely disappointed in my new Whirlpool washer dryer matched set. My washer started to leak at less than 6 months of age, and my clothes are extremely wrinkled due to excessive spin and smell absolutely foul. I have adjusted the spin cycle to the lowest setting to prevent wrinkling as suggested in the product materials. I have cleaned the washer with the recommended product on the clean washer setting, although now with the leak, that means a good floor mopping too!I have contacted customer service about the leak since the machine is still under warranty - and they gave me a 4-hour window on a specified day for the service. I took the time off work and the technician failed to show. I called twice to follow up on his whereabouts and ETA. They did nothing except tell me to keep waiting. 45 minutes after the outside hour of arrival had passed, I called again. The customer service offered to make me another appointment so I could take another half day off work and hope he would show up the next time. When I asked for a preferential booking (with a real time) to minimize taking more time off work, the manager said all she could do was give me another 4-hour window. I said that was really bad service and she hung up on me! Another rep did do a little better - he sent me a name and number and said I could try to book an appointment directly and hopefully minimize the additional time off. Its the last Whirlpool appliance Ill buy - with that kind of customer service, Id rather be out pounding my laundry on a rock.

Started researching online about a week ago because my dryer was making an awful noise. Found out that the new idler pulley system the company used in my Whirlpool cabrio washer & dryer model (WED5500XW0) was so ineffective that they have since started replacing it with the old part #691366 they used to use. Also I am having a problem with my washer not spinning all of the water out of the clothes. Found out that this is a common problem with this model (WTW5500XW0).Had a certified repairman out to replace the dryer idler pulley system. He also calibrated the washer to see if that may help (it did not). The repairman said that some of the Whirlpool washers had been recalled and he had actually replaced some control panels and that seemed to work. He suggested that I contact Whirlpool. So I contacted Whirlpool, thinking that they obviously knew that there have been many problems with these machines (idler pulley part being discontinued & and recall on SOME models), and thought they would be more than willing to rectify this problem. Well think again! The two young ladies that I spoke with sounded like robots, Unfortunately, you are not within your 1 year manufacturers warranty so there would be nothing we could do at this time. Although I must tell you, the second young lady I spoke with did offer to sell me a new washer at a deep discounted price of $386 (which is only $86 more than fixing the washer). I think everyone who has a problem should contact Whirlpool and express this dissatisfaction. And if you are shopping for a washer and dryer, stay away from Whirlpool because their customer service is disheartening.

Late on the evening of Monday, January 27, 2014, after springing a leak in my 8-year-old water heater, I purchased a new Whirlpool model N50T61 replacement from Lowes. Installation went smoothly and the unit lit off fine the first time. It heated the initial tank of water rather quickly, but the next morning, I noticed the status light on the control unit was not blinking, which indicated the pilot light had gone out. I relit the pilot light, the water heater fired off and appeared to be working properly. 12 hours later, the status light was out again. I relit the pilot, but within 20 minutes, it went out again.On Wednesday, the 29th, I called Whirlpool customer service and explained to the representative what had been happening. He stated that since the status light was not blinking a code, the problem was either an air supply or venting problem, and he couldnt help me. I relit the water heater again and performed the match smoke test described in the owners manual on the vent connection. It did exactly what the manual said it should do, so I assumed that was not the problem. However, while performing this test, the water heater went out again. This time, being right there when it shut off, I saw the status light blink twice about 5 or 6 times before it quit blinking all together. The two blink error code indicated low millivolt signal from thermopile.I called customer service again and explained to the representative what the first person had told me and also told him the results of my test and that this time, I had observed the two blink error code. He asked if I had a multimeter (which I do), so he had me disconnect the wires for the thermopile, connect the meter to the wires, light the pilot and read the voltage. My meter is an old analog unit, and not capable of reading millivolts (which is what the thermopile output is), and I informed the rep of this, but he had me do it anyway. As I suspected, I saw absolutely no reading on the meter. The service rep stated that he believed the error code and decided to send me a new thermopile assembly. However, their shipping department was closed for the day and I should not expect to see the new part until Friday. This was unacceptable, but he stated that this was the only option available to me.After thinking about this situation for a while, I again called Whirlpool customer service and told the representative that I was not satisfied with the solution previously presented to me and that I wanted a return authorization to take the water heater back to Lowes for replacement. The rep stated he couldnt do that, but said that there were a couple other things I could try. He attempted to explain these procedures to me, but wasnt able to do so clearly. He stated he would email the instructions to me. As of this writing, I still have not received the instructions.In the meantime, I did some internet research and found that Whirlpool water heaters have numerous chronic problems, including the issues I was experiencing. I decided this was not a product I cared to own. I called the Lowes store where I purchased the water heater and spoke with the manager. I explained the entire sequence of events to him, and he told me to bring the water heater back for a full refund. Since my local Lowes store only sells the Whirlpool brand, I took the money and purchased a different brand of water heater from another home improvement store. Needless to say, it will be a cold day in hell before I ever purchase another Whirlpool product.

I have a Whirlpool AccuBake gas range. I started by contacting my local repairman because my stove was out of warranty. The first company came out 3 times and replaced three parts, which didnt work. The cost was $297.00. I originally paid $598.00 for the stove. After they deemed it non-repairable, I contacted Whirlpool. They basically said it was my fault for not buying the warranty. I then contacted the BBB. Anne ** from Whirlpool contacted me and had another Whirlpool service tech come out at no charge to me. But guess what, they deemed it non-repairable too. Its a shame that companies no longer stand behind their product. Its very apparent that this is a manufacturers defect. They should replace the stove.

I purchased a Whirlpool refrigerator in 2014. It is a side by side with ice maker in the door. About 8 month ago the ice machine stopped working. I called an appliance repair center and they diagnosed the problem as being the control board for the ice machine. After only 3 years this stopped working? I gave them to OK to fix it. A few days later I was informed that the part is on backorder for a few months. Well a few months has become 6 months and no part is available. I contacted Whirlpool and they called me and promised a solution, but then they never contacted me again. So it is almost 7 months later and I still have no ice. How can a relatively newer product break down and then not have a part available? Whirlpool absolutely does NOT care about their customers and does NOT back their products. Stay away at all costs.

I bought a Cabrio from Costo less than 2 years ago. Dryer so far so good (big barrel with hair dryer so what could go wrong?). Washing machine is HORRIBLE. Lid latch broke (couple hundred to repair). Now out of the blue I get an F2 error & machine is completely inoperable. I am only user & very careful with it. There should be a recall on this expensive junk. NEVER buy Cabrio or maybe any Whirlpool appliances again. Ive never written a bad review btw.

This is a good looking, inexpensive stove/oven. Stove top has four burners. I liked the split grates on the stove top. Its easier to remove and clean. I do not like the rubber seal on the oven door. I am used to the heavier duty seals on most oven doors.

I have had too many problems with the thermocouple beginning about two years after I purchased the water heater in 2003. Whirlpool keeps replacing the thermocouple, but I have to pay for the plumber to come out and repair the unit. This runs me about $180 each time. The thermocouple has burned out three times since September of this year. The plumber didnt charge me anything the second time it went out. But it went out for the 3rd time today and he recommended that I replace the unit. Of course, it is out of warranty and Whirlpool was happy to tell me that I could purchase a new thermocouple at my own expense from them. I have paid for this water heater three times over with repairs. Whirlpool knows that there is a defect with the design of the water heater. There is no way that a regular consumer can get inside the water heater to clean it. I will never purchase any Whirlpool products ever! I advise anyone reading this to follow suit.

I bought the french door refrigerator Sept 2014. Recently the change filter light came on so I bought the filter. I read the instructions and then when I went to install it, the filter door would only open about 10%. I called Whirlpool and explained it was obviously a manufacturing error. They didnt care. Out of warranty. Everyone can make a mistake but when you wont own up to it and take care of it, that defines your character or lack of it. I think I will video the whole thing and put it on YouTube.

I bought a Whirlpool refrigerator about 1 1/2 years ago. Mechanically it works fine, but many places on the outside are showing small rust, circular rust spots. Looks like the refrigerator has the measles. I dont think ordinary paint will cure the problem since it looks like the rust is coming through from the inside of the door. Any ideas as to what will cure the appearance and keep the rust hidden????

I am following up on a review I submitted on April 22, 2015 about a Whirlpool refrigerator with french doors and bottom refrigerator. At the time, paint was falling off from the door as pictured in the previous review. This another chapter on this story and probably the closing chapter. A few months after the paint event which I could have lived for a while, the right door hinge literally disintegrated leaving the door without support. The door seals material is of such poor quality that they have disintegrated and the water condenses inside. The bottom photo shows hinge components that came off the door hinge on the kitchen floor. The second photo from the bottom up photo shows how the door scraped the plastic of the freezer door top trim if the door is not lifted to clear it. The second photo from top to bottom shows the door over the hinge pin if I am not careful lifting the door to clear the freezer door.The first photo from top to bottom shows how the door remains open if not lifted so that the door magnetic seal keeps it in place. It is very hard for me to believe that a country like the United States of America treats its customers with no respect. I met my obligation to pay the amount on the price tag of this appliance but I cannot say that Whirlpool did its part of providing a basic quality product. There is no consumer protection agency in this country to protect consumers from corporate predators that have no sense of a fair deal with a customer. So here we are, being abused by United Corporations of America. I hope the future brings a different understanding of the american people on these matters. Thank you for the opportunity to express myself on this matter. Next step... buy a foreign made appliance that will support another country work force... sounds familiar.

Cannot reinstall oven door after glass cleaning. The worst design and absolutely no support from Whirpool. They said the instructions are in the Manual. NOT TRUE!!!. The person on their helpline said she did herself. It is simple.. Total BS. Here is the link to hope to maybe get it fixed: ** Worst stove ever.

I purchased the refrigerator in Nov. 2013 and it stopped working completely on 3/22/14. I called Customer Service and they told me someone from Apple Appliance would be here on the 24th, it is now the 27th and still no repairman. I have contacted both Apple and Whirlpool everyday and have gotten no satisfaction at all. I just found out that I will have to wait until March 31st to have someone here. I have lost everything in the freezer and refrigerator and have no way to cool anything. I find this unacceptable but have no alternative but to wait until Whirlpool does something about it. I will never purchase any other appliance from them.

Purchased our Whirlpool Gold Oven in October of 2013 from Best Buy. The oven works fine, but using the oven to make pizza on March 30th of 2014, a fire started in the drawer under the oven. The oven was set at 400 degrees. Several oven mitts were stacked in the drawer. There was no major damage done to the range, other than a bit of discoloration to the white trim, but we will never put anything in the drawer under the oven and would advise others to do the same.

Extremely disappointed!! We purchased this water heater about 4 years ago and for the past year we have to manually turn on the burner. Its been a nightmare! We called Lowes to purchase the parts, but they do not sell the parts. There was a nine year warranty. Our last water heater lasted about 11 years. Its such a shame that this one is giving us problems just after 3 years. Im really considering just buying another one. I dont want to continue struggling with this one. Its been a bad purchase and coming to find out that Im not the only one with this problem. If its a defect Whirlpool should at least replace them for the inconvenience. They should take responsibility for selling defective products.

My Cabrio washing machine is 3 years old, and is working the way it has been designed to work. It does not clean clothes and it consistently has a foul odor. Due to the odor, I must use the cleaning cycle with Affresh (pricey product) 3-4 times weekly. Even that is insufficient. Because it is in an indoor laundry area, the odor permeates the hallway and nearby bedrooms. The extra cleaning cycles are contrary to the energy efficiency of the washer, and detrimental to the severe drought conditions in California. When I contacted Whirlpool about my situation, they recommended I substitute bleach for the Affresh to keep the cost down.

I purchased a Whirlpool washer in March 2007. That washer is now leaking from the bottom. I called Whirlpool. I was told that the machine only had a one-year warranty, so repairs would be at my expense. The CSR then offered to schedule a service call for me at $139, which I refused. A few weeks later, I received in the mail an offer for an extended warranty on my Whirlpool washer.

Two-year old Whirlpool Cabrio top load washer; absolute piece of junk! Bearing on the drum howls like a train. Now the master board or some other sensor (under drum) is out. Serviced for the third time and the service repairman states its cheaper to replace than to repair. For a 2 person household, it is reasonable for us to expect more than 2 years from a washing machine. Same experience with Whirlpool 15 years ago. 1st time shame on you; second time shame on me.

We our adding our name to a list that is remarkably long. We purchased a top loading Cabrio washing machine just over a year ago and the problems with the balancing of the unit are the same as everyone else who has written in. The service company A&E has promised a lot but has done little to resolve the issues we have had with the machine. One representative told us that she would order the part and have it sent to our home. When the part did not arrive, we called A&E back only to find out it was never ordered because the service technician would not return their phone calls. I find this excuse ridiculous and similar to other false statements they have given us on the other four phone calls made to address the problem. After reading these reviews, we realize that this is only the beginning of what will be a frustrating and costly experience. Never again will we buy a Whirlpool!

I guess I am in the lucky group because my washer lasted about 3 years before the problems started. The latest is the lid lock light flashing, the machine doesnt go through full cycle but stops in the middle, doesnt spin and drain. Even before that the clothes didnt come out clean. The repairman said that this product is basically disposable and it makes more sense to buy a new washer than to invest in fixing this one because something else will break next.My old White Westinghouse lasted 18 years without one problem, Im sorry I wanted something new. What a pity that companies nowadays sell junk and the consumer has nowhere to go with a complaint. Im wondering if someone has the name and the address of the CEO of Whirlpool, I would like to ship that piece of junk to where it came from... it would be funny if other customers did the same. And I agree with other posts that class action suit would be in order... too bad nobody started it yet. I wish I had read the reviews before I made the purchase but at least I know now to stay away from all Whirlpool products and do whatever I can to prevent other people from making the same mistake I did.

Whirlpool Refrigerator: Model # WRT111SFDW - We bought this frost-free frig. in Feb of 2016 and this Feb. before the year was up, it started freezing up. I called the Co. and they sent a young man to my house to fix it and he thought he had. Well 2 wks after that it started freezing again and I called the Co. again and the same thing happened again and this was after my warranty had expired. Well then this young man came out and replaced the fan and a heating rod I believe to help it to stop freezing. Well 2 days ago it started freezing up once again. Im disabled and live on a fix income so now Ive got to figure out to get me another frig. And it WILL NOT BE A WHIRLPOOL REFRIGERATOR. But kudos to the Co. and the young man for trying to fix it even though it took 3XS and still not working.

We purchased a Whirlpool refrigerator (Model WRB322DMBM00) in April of 2015 from Lowes. Within 5 months rust stains started to form at the bottom of the top door and the top of bottom drawer. RUST STAINS!!! We do not live in a humid area or near the ocean. It is a design flaw I believe in the gaskets. I called Lowes first for their guarantee but they said it was cosmetic and not covered. Then I call WP customer service and they are sending new doors. Thats fine but its going to happen again. I requested slate instead of stainless steel but they wouldnt do it. Plus finger proof is a joke (monochromatic). Very dissatisfied customer.

Updated on 02/13/2021: Company fails on customer service. My stove’s trim is rubbing off on my Whirlpool stove only 6 months old. No chemicals were ever used to clean the surface. This trim piece surrounds the controls and is not covered under warranty. An expensive cheaply made stove. Multiple attempts to have the piece replaced got nowhere. A letter sent to the head office was deferred back to customer service. Whirlpool has lost credibility and I will no longer buy their products.Original Review: So disappointed to find the paint finish coming off the trim on my 8 month old Whirlpool range. No harsh cleaning chemicals were used. Only mild dish soap and a microfiber towel. The trim, attached to the control panel on the front of the stove, is not actually stainless steel, but painted to look like stainless steel. Whirlpool warranty doesnt cover esthetics and refused to replace the trim, stating replacement would include the entire control panel and it is not covered under warranty. So be prepared to have your new expensive stove look old in a matter of months.

I got the Cabrio Washer and Dryer set in December of 2015. By March of 2016, the heating element and dryer door latch had broken. Had to have those repaired. By June of 2016 and since, Ive had several repairman out to the house trying to figure out whats wrong with my washer. 9 times out of 10, it will not spin the excess water out and the clothes are soaked. Sometimes it takes me an hour to get the washer to go through a spin cycle. Sometimes the washer wont go into a cycle at all, it just makes a horrible noise (like its draining) and never does anything. It doesnt put out enough water in larger loads, so Ive had to cut my load size in half. It wont work on half the cycle options on the screen, only working on bulky or heavy. Wont wash on normal or quick wash or any of the others. It will make that same horrible sound and do nothing. Nobody can tell me whats wrong with the stupid washer and the repairman said he sees issues with Whirlpool all the time. He said save myself money and buy something else. But I remember a time when a washer and dryer would last for 20 years. What happened to quality products and craftsmanship. I am so tired of the new and fancy appliances that dont last and these companies that dont stand behind their products. Whirlpool you should be ashamed. I will never buy another one of your products. There should be a recall on these particular Cabrio units especially after all the horrible reviews I just read.

Cabrio Platinum Washing Machine - We received this washer and dryer set as a gift so I cant complain on the cost. However, it does NOT clean your clothes. Water smells at the start of each load, clothes are left with soap scum and several clothes have been ruined by oil stains!

I will never touch the premier Whirlpool Brand Again. This is the two door fridge + drawer freezer, model GI7FVCXWY0After about a year, and I think it lasted this long because the ice maker was off during winter (because unless you use it constantly you have a solid block of ice), after a year it stopped making ice and poured water out from the top of the fridge. Expensive extended warranty came and replaced the Ice Maker, which (about a year later) has just started leaking all over the floor (again).This I suspect was a protest against using all of the ice one day. It froze up, which causes the leak, froze solid items that were in the fridge compartment (and spoiled some items).The other design fault is while the right hand door will stay open, the left will not, it closes. But it does not close properly - just enough to make you think it is closed.Dangle beers in a nearby stream, keep your food in the cellar, dig a deep hole in the backyard, learn to eat all your food the day you buy it, but do not buy this fridge!

Like the load sensor feature the best, so economical, the drum is oversized to wash duvets and heavy blankets. The fact that the washer and dryer are stackable makes them ideal for apartment living.

I have had my Whirlpool refrigerator 14 years and have had service on it only 1 time, for the ice maker. I have had a fridge where the compressor went out twice. Dont remember the brand but do remember the experience.

We have been very happy with our appliances that now over 11 years old and doing well. We love our gas range top. They gave greater and new models so we love Whirlpool and GE. We always get great deals at Home Depot.

I bought a pair of Whirlpool front loading washing machine and dryer on May 23, 2011. The Duet Steam washer model is WFW9640XW, dryer is WED9470WW. Their high retail price was $1125 each. I did not pay this for them. I thought I got a great buy at Lowes for the price I paid, plus their 4-year extended warranty. Whirlpool used to be a very high-end appliance manufacturing company. Now, all they put out the back door is junk. I would advise not to buy Whirlpool front end anything. My washing machine started making noise about 2 weeks before I reported it to both Lowes and Whirlpool. The noise sounded like bearing not being lubricated, which that is what it ended up being.The noise got so loud that even with all my very expensive electronics (my home entertainment ctr equipment) I could not hear the TV which goes through an expensive Yamaha AV Receiver and those expensive Infinity speakers 7 channel system. The main bearing for the wash drum assembly was bad. After two emails and several phone calls to both Lowes and Whirlpool, Whirlpool was going to send the so-called re-engineered drum assembly. The style I have is 3 parts; the new one according to Whirlpool is one part, but if they put the same bearing in, youre going to end up with the same problem in another year. I live in a condo of just over 920 sq. ft. so really there is no room to repair them in my home, but that is what they are going to do. I will be getting the new drum assembly delivered to my condo and have the repair company doing this dirty job in the middle of my living room.Living in a condo, I have a small utility closet next to the kitchen where the furnace, hot water tank, and washer and dryer are. The closet needs to have some areas cut out with and installed two small hinged doors on each side, so if anything ever needs to be repaired or replaced, there would be a little bit more room to move items in or out. The problem getting the washer out is getting the dryer moved so you can disconnect the electrical plug, cold water hose for the steam, plus the vent hose. First, you have to get to the water valves which are very hard to reach. Because of the way cluster housing is made, they squeeze things into very small holes like the faucets and drain hose are located. I was asked by the repair person if I could help him lift these items out of the closet. I have had 7 fusion back operations and #7 left me in constant pain that I take a narcotic drug for pain daily. So, I called Whirlpool back and said the repair people were only going to send a tech. I was told that it is a two-man job: one tech and one helper. So Lowes needs to authorize two people since Whirlpool is sending the new drum assembly for free. I wish I could have gotten a new washing machine with the so-called re-engineered drum assembly. I am still probably going to have to squeeze between the bulkhead (wall) and the washer and dryer to disconnect everything since I am a small person. If I wasnt retired, I would have bought a different brand front loading washer and dryer, probably Bosch and took the loss on these piles of Junk. I love my country and do my very best even as hard as it is in this day and age to buy US. I served my country in the US Navy during the Vietnam War, just to see the civilians willfully buy Asian everything. So now, we have 4 Asian nations that own this country. I dont know why Whirlpool changed from a company that you could trust their products to a company that doesnt give a damn what they put out the back door. These companies still havent gotten the clue why folks buy goods from other countries. I think they need to open their eyes, but I guess with Whirlpool still being a company that is selling a very large number of appliances and making money off of us, suckers, they dont need to change. The only way they are going to change is if folks stop buying their junk.

Cabrio washer broken lid, asked WP to fix warranty. They offered $250 off $500 Amana washer. Said just send me the new lid that would cost me $210. They said no. Asked if they would send me metal lid with hinges less than $100 they said no. Told them I was not going to spend more money with WP, my turn to say no. If you are wise dont buy WP products...

My refrigerator was purchased in May 2014, and died in August 2015. Before it died, it produced a very loud, rattling noise for two days. Thus, the refrigerator cost me $100/month. It does seem, upon reflection, I would have been better off buying a piece of junk for $50. It would have lasted longer. Additionally, the so-called stainless steel started rusting all over the front surface, first popping up in one spot, then another. One year old, rusty and dead. Great job Whirlpool. Buy American.

On May 15, 2017, I purchased a new Whirlpool Water Heater, unknowingly made by American Water Heater Co., from Lowes (receipt attached). Model Number ES40R10-55 with a 10 year warranty. The water heater was installed using the directions in the owners manual. Upon turning on the current to the water heater after it was filled with water and all air removed from the plumbing, the module gave a code stating the top element was not working. Called the Technician Assistance Hotline and they gave me a RA number to get a new top element from Lowes. Got that on May 16 and had to call the plumber that is contracted by American Water Heater Co. to come to the house and inspect the heater to make sure it was installed correctly.The water heater worked once the new element was installed. On Oct. 3, 2017, had more issues with the module stating the top element was not working. Called the Tech. Assistance Hotline and they gave me another RA number to get another top element. On Oct. 4, got the top element and installed it. The water heater started working again. On Oct. 6, the module stated the bottom element was not working. Called the Tech. Assistant Hotline and had the plumber come out. He determined that he could not find out why it was doing this and also said that both elements were good along with the element that I removed on Oct. 4, which I still had. Since then, the module has been giving codes stating that both elements are bad and I have not had any hot water since Oct. 7. American Water Heater Co., Whirlpool, and Lowes all refuse to give me a refund for this piece of junk! All blame the other for the problems and none will take any responsibility for the water heater not working. I will never buy another appliance with the Whirlpool name and definitely will not buy anything made by American Water Heater Co. I also will never buy another appliance from Lowes as they are not willing to help me in this matter. If you do not want to experience the headache and frustration of owning a new appliance that does not work, I would suggest that you do the same!!!

As many others have posted - the Cabrio washer is awful. Cycle time > 1 hr. Clothes not clean and caked in soap even with extra rinse. Phone Whirlpool and found they dont care. All theyd say is its government regulation fault but for $100 they could send a technician to ensure it is working as designed. To environmental reasons for the new design, seems to me it missed the mark. Longer cycles, extra washes, extra rinses... All I can say is - Unbelievable!!!

On Aug. of 2013, purchased A Whirlpool refrigerator with ex warranty to find out the bottom freezer door started to RUST!!!! They said it was not covered????? WHY!!!!

I purchased a Whirlpool refrigerator in Aug 2012 model G16FARXXF05 and in July 2016 the compressor died. I researched refrigerators before purchasing and was told by every store I visited that Whirlpool was probably the best and with the least problems. Unfortunately, for me that was not the case. I guess anyone can get a lemon!!!

This machine is junk. It does not get clothes clean. I had jeans that I soaked and were fairly clean when I put them into wash and had another pair of jeans with a little dried mud. My whole load came out filthy. I am having to rewash the whole load after hand cleaning the washing machine. I replaced a machine that was 25 years old that did a better job than this piece of junk now sitting on its place.

I am having the very same problem with my french door stainless steel Whirlpool gold refrigerator. Water pooling in the bottom of freezer, freezing into a solid sheet and then leaking onto the floor. It is less than 2 years old. Apparently, this is a significant defect in this problem seeing how so many people are having the same problem with the same fridge. Has anyone reported to BBB? Im thinking class action lawsuit. Im getting ready to have to repair my kitchen floors as a result of this defect. I will be talking to my brother-in-law attorney about this and will post his response/recommendation. Whirlpool should stand behind their product and make this right.

This washing machine is a piece of junk. It broke down exactly 2 days after the one year warranty expired. Home Depot said there was nothing they could do and Whirlpool said the same thing. This washing machine was not used on a weekly basis. It perhaps washed 20 loads during the course of the year. I had many issues with the sensors before it broke down completely. Sometimes, half the clothes would be dry after the entire cycle. I was so angry that I had a local independent contractor come in and look at it. He said the motor was broken and needed to be replaced. So much for $700 down the drain. I will never buy a Whirlpool product again. This was the worst experience Ive ever had with an appliance.

Bought this machine in Feb 2007 as a pair Whirlpool Cabrio. I loved it for almost two years. The control board went out, Whirlpool replaced it. A couple of weeks later, the F-1 codes started then the F-51 codes. On July of 10, it was code after code. It sounded like a jet taking off and constant unbalanced load. I called repairman and was told to go buy new machine as repairs would start at $500 and since I live in a rural area, no one wanted to waste their time. Two repair techs told me point blank they wouldnt even touch it. We paid $1000 for this machine and we live pay check to pay check. I spent four months trying to get Whirlpool to do something. I kept getting told I should have bought extended warranty. Machine has been sitting under stairs for over year waiting to see if class action or recall can be done. Also when control board was replaced, the repair man told me it was rusting away from the inside out. My husband had to find us a used washer and this thing has done nothing but cost us money. So much for efficiency. Everyone posting here also needs to go to Whirlpools Facebook page and post there.

We purchased a Whirlpool Gold French Door refrigerator with a bottom freezer in Dec 2009. We discovered a leak dripping onto the finished basement ceiling. We discovered after several attempts that the plastic evaporation tray was broken (since day one). Previous defrosting had obviously evaporated into the hardwood until now. This item, although obviously broken when installed, was not fixed as the warranty had run out.Boo to Corbiel and to Whirlpool. They are financially not worth a lawsuit.

Friends and family dont you ever dare to buy a refrigerator from Whirlpool - Best Buy!!! They sold me a defect refrigerator and after 2 months begging to see a technician, they are telling me that they are going to fix it. Im so tired of them trying to fix it. Theyve been here 4 times with no luck. All my food is rotten and frozen. And its a new refrigerator. Gosh. As you can see, the water in the plastic cup that I left in my refrigerator are frozen which is not supposed to happen. I feel that Im dealing with nonsense. They dont care. They just took my money and thats it. Im left with a new defect refrigerator that doesnt work. Ridiculous.

Our Whirlpool is 8 years old and - knock on wood - it has been very dependable. It has enough settings to take care of the range of our dirty clothes. It is a front loader and I like that type - it gets the clothes clean in cold water.

I love my Whirlpool gas stove and oven. We opted for the convection feature as we are a family of 7 and often need multiple items in the oven. This was a very useful detail. I didnt know I needed that. I now cant go without!

New stainless steel range 5.3 cu.ft. with convection oven delivered by Home Depot on time. Before the day was over the trim around oven glass was falling off. Double sided sticky tape was not holding. Yes its put on using double sided sticky tape. Called Home Depot, once you accept it, you deal with Whirlpool. They must first send someone to look and see. Yes its falling apart. Service tech will order new door. Mind you it will also have the sticky tape. We have also noticed that the glass top has many deep scratches, he will replace that also. A week later still no word, when. Used the oven because I couldnt wait and as it heated up smoke poured out of it and a loud noise from inside. Turned off and pulled out bottom drawer to unplug. Bottom panel had fallen down and undersides were rusted. Only had the stove 3 weeks and its Christmas Eve. Will read reviews first next time. No problems with my other Whirlpool appliances.

This is a freezer on top unit. Purchased in 2015, unit quit cooling, started making a roaring noise. Called local technician, he added 2 oz of Freon, said he has seen many of these same unit losing Freon. Technician said line that goes to compressor is copper and hooks up to aluminum line before attaching to compressor. This is leak point for freon; no way to know when the leak started, but freon almost gone and cost to pressure check for source of leak is costly and probably would not repair problem. Got 6 yrs out of it and I am replacing with another brand. Will never buy Whirlpool again. Should have got 10-12 yrs of use. Do not buy this unit. Wrote Whirlpool first, but no help. Indicated this could be a problem with these units but no recall so I am on my own. Out $900 for a new refrigerator. Big hassle. Unit no good.

In August 2011, I purchased and had installed a Whirlpool Wall Oven RBS305PVQ04 for $1000+. In July 2014, the oven failed with blown internal fuses and a thermostat $225+. In November 2014, the oven failed again, this time with a failed controller board. Whirlpool claims there are no replacement parts after just three years! In calling Whirlpool customer service for help, they basically said tough luck! NO parts, NO adjustments, NO service, you own a boat anchor. I tried to buy American; boy, was that a mistake. So it cost me $415 per year to own this LEMON. DO NOT DEAL WITH THE WHIRLPOOL COMPANY!

After having our refrigerator for a few months we noticed rust on every stainless steel panel on the front of the unit (6). After customer service sent a technician to look at the unit nothing more was done. I was just told to try and scrub the rust off.

I bought a Whirlpool model GI7FVCXWY00 over and under refrigerator directly from Whirlpool through DirectBuy on April 19, 2010. The unit was a relatively high-end model (over $2,000) that came with a 12-month warranty. Thirteen months after purchase and 1 month after warranty expiration, the ice maker stopped working flooding the kitchen in the process. We called Whirlpool who recommended one of their authorized maintenance subcontractors (GuinCo) to appraise the problem. GuinCo came out, diagnosed that a valve in the ice maker had gone bad and the repair cost us $364. We chalked that up to Murphys Law (repair needed immediately after warranty expiration). Not 4 months later, the kitchen comes up flooded again and again and the ice makers not working. We call GuinCo, the repairman come out and said this time that its a heater and ice maker defect which will cost $643 to repair. He also said that the unit has been designated as having a design defect. We held off on the repair until we could contact Whirlpool for some remediation since it has become obvious that the unit is a lemon. I called Whirlpool, laid out the problems, timelines and potential cost (ice maker failures are going to cost us almost half of what the entire refrigerator cost before the unit is a year and a half old) and the only response they had netted out to was: Sorry, you should have had extended warranty. This is a prime example of an American manufacturer, marketing an inferior product and offering the customer nothing when the lack of quality becomes obvious. I will recommend to anyone I know to stay as far away from Whirlpool products as long as I live.

I have spent 30 minutes trying to change light bulb under the oven and get the cover plate back on. I watched the film on how to do it, it was amusing to watch the struggle to get it on. It was amusing to say the least. Whirlpool watching it??? I do not believe whoever designed this worthless time consuming light cover never tested it one time, or it would had been more user friendly. It amazes me what kind of trash they can build for us consumers to have to deal with at times. Tomorrow this overhead piece of junk is coming out and being replaced by a non Whirlpool one. I am going to get a tractor and smash it into little pieces and put on side of street with a note saying this is what happens when you try for an hour to change the bulb.

I bought Whirlpool gas water heater on July 2009. It keeps going out. It is not working. I found out you cant even get parts for fixing it. The dealers told me its junk. I was told to buy a new one. Then, I found out its been in class action lawsuit. How did I get to buy it after it was recalled? I dont know what to do.

I call them. Lowe's gave me #. Spoke to man there at CS. He took care of me. I was a Lowe's within 30 mins. Gave them PO. Home within 45 mins. Whirlpool you the best in Johnson city TN. You're just like Lowe's. I pay for Whirlpool because you make it. Thanks for all you do. The best. #1.

After 14 years of good service with Whirlpool Duet front load washer dryer set, wife chose Whirlpool kitchen appliances as part of a kitchen update project. All matching fridge, range, microwave hood and dishwasher. What a nightmare! The icemaker growls and whines all the time and the dishwasher was broken before being packaged at the manufacturer. A wheel from the middle rack was missing when the dishwasher was opened. It wasnt in the sealed dishwasher nor in the box. So it had to have been broken off before the item was boxed. We called for warranty claim and A-1 Appliance was recommended out of Shreveport, LA. In a few weeks he showed up, looked at the rack for a while and said Ill have to order a new part. I said fine. (How hard can that be? Right?) So here we are 5 months later, unable to use the middle rack because it cant hold any weight with the roller missing. Multiple calls to Whirlpool and A1 and we keep getting promises and runarounds that turn out to be lies. How hard is it to say go to your local Lowes and well authorize them to give to give you a rack from an in-stock dishwasher? Let Lowes wait on the new part! Sounds simple, and any other company would have done that, or told us to return it to Lowes for another one. But NO! Whirlpool just whines about being behind on parts, shorthanded, or lies about the part is in and its A1s problem now.So, today, same story. A1 says they need 2 parts. **! Its one part. Whirlpool says A1 has the needed part. Same old runaround. So, we just replaced our 14 year old washer and dryer with NON Whirlpool units. $2500 more in of appliances that Whirlpool could have gotten, but Im guessing they dont even care about missing and losing sells. They certainly do not care about warranty, parts, quality, customer satisfaction or repeat customers. Never again with Whirlpool! Beware!

The main control panel on my Whirlpool Cabrio Washing Machine broke twice in the second year of ownership. I bought this in 2006. The part was replaced in March 2007 and then again in October 2007. Now, it is broken again and Whirlpool says too bad, they will not replace it again and will cost us $275 to fix it. People have posted about this problem all over the internet. How can they not help their customers and recall this washer part?

I bought a brand new Whirlpool washer and dryer set -Cabrio- $1700.00 in 2011. It is by far the worst washing machine I have ever purchased, and I am 60 years old!!! It is now three years old and has been repaired at least 4 times. Long story short... after hours & hours on the phone, along with many threats! (By the way I had to ask for a manager two times up the ladder for this to happen as they just kept repeating that it was out of warranty coverage). I also told them that I was going to have one of my company trucks deliver this machine to Sears lot, along with a paid person to inform every shopper of my plight with this washer and the lack of service from Sears and Whirlpool! Whirlpool finally agreed to pay for the parts but not the labor on this most current repair. (This time it is the transmission!! In the past it was the Hub, twice. The gear case twice and the belt a number of times). I am now going back to Sears to request (that might not be the correct word) Demand, that they take care of the service bill for this machine. In between repairs, I have dealt with ongoing cleaning quality problems. This machine does not get clothes clean. I always have to wash them twice. This machine is loud. This machine does not use enough water to even dissolve the soap. So much for energy saving measures when you have to wash twice and still see soap and crud in the tub. Worst, worst, ever washing machine in my life!! By the way, I have an 8 year old Maytag too that I have never had to repair. Moral of the story, buy Maytag, or at least do not buy a Cabrio!!!!

Do not buy a Whirlpool refrigerator. Worst product ever. Literally broke within 3 months. Needs a new compressor and evaporator. They will not exchange the product and the parts are on back order for 3 more weeks.

Purchased first water heater in 2008 with 6 year warranty. In 2011, pilot light would not stay lit. Whirlpool told me to go to Lowes and get a new one at no cost. But I had to pay for service to identify the problem and installation of new one, costing $250.00. A year and a half later on a six year warranty, the same issue the pilot light not staying lit. They send a pilot light assembly and we pay the shipping and installation cost of $130.00.Two years later, the same issue begins again. Calling tech support, they determine it needs a third pilot assembly at $30.00 for shipping and $265.00 service installation fee by a certified Whirlpool technician. Worked one day! Im so done with this company!!!! I was promised a call from a supervisor with Whirlpool which Im still waiting on days later. Probably for the best at this point. I think I would feel better if I could beat the crap out of a Whirlpool CEO with it! Im cutting my losses and going with a different provider. I will NEVER again purchase another Whirlpool product!

My elderly mother purchased a Whirlpool Cabrio washing machine in 2013 (Model Number WTW8600YW1). It never filled properly with water. It evolved to a sensor and circuit board issue that Whirlpool never totally remedied. Hence, the machine never worked properly. This 800 dollar purchase on an elderly persons limited budget had to be utilized minimally. Now fast forward in 2015, even with minimal usage and white glove handling, the machine is displaying an F51 error. You guessed it, Whirlpool will not remedy the issue, although it is well-documented to be a widespread complaint hence clearly a product defect. Shame on Whirlpool, their business practices, and what amounts to theft of an elderly womans finite income. I have advised my mother to trash the useless Whirlpool appliance and purchase a Kenmore washing machine, of which I have been the proud owner for 10 years, doing laundry for a family of 5.

I have enjoyed my stove for 16 yrs, it is very reliable and easy to use. The heating elements work well and heats up quickly. During this time I have not had any repair done. The areas of improvement that needs to be implemented is the inter glass that is installed at the front looking into the oven. In order to clean you have to take the front door off which is very difficult to put back together.

I bought my house brand new with all new Whirlpool Gold Series appliances. About a year and a half from purchase date, I started having issues with my fridge, then my dryer, then my washer, then my fridge again and that lasted about 5 months, then my microwave and my dishwasher. My microwave stopped working in January. It’s now April and I still do not have a new one. It keeps getting lost or shipped to the wrong address or something. Every time I call, the representatives don’t know how to look it up. I wind up on hold for at least 30 minutes, and I get transferred to at least 3 different people. I hope my last appliance doesnt break because I’m over Whirlpool, and I will never buy another appliance from them again.

I have a Whirlpool top-loading washing machine model 3LA5580XSW3. The timer switch is not working and I have been told that spares are not available. Is this true? Everything else works well. Please advise as I really need a new timer.

Whirlpool cabrio top loader is junk from the first month. My washer has had way too many repairs. A&E repair has been a frequent at my home. Now Im getting ready to repair it again! Hub gasket or pump not sure this time. All has been replaced previously. Never ending - always something wrong with it!!!

I purchased my Whirlpool microwave model WMH2175XVS-2 in March 2011. The magnetron went bad 3 years and 1 month later. Thats only 37 months! Whirlpool is very sorry but of course the warranty is expired! Oh by the way, I replaced a microwave that lasted 10 Years which was a second microwave (which is still going after 15 years).

Whirlpool Cabrio Washer WTW7340XW sounds like a small jet during spin cycle. The Whirlpool Cabrio Washers have a very well known and well documented problem with the tub bearings failing. Many many disgruntled owners have posted their complaints online, and there are many videos showing the issue on youtube. This issue is so prevalent that the manufacturer has created a tub bearing failure repair kit for $350. The repair is so expensive and labor intensive that many of the certified Whirlpool repair shops no longer work on the Cabrio washer stating that a better washer can be purchased for the cost of this repair.That said, the manufacturers customer service group denies that the Cabrio tub bearing failures is a common problem and are quick to state that Whirlpool holds no liability for this problem. Ramping the complaint up to a customer service supervisor is met with the same canned response. Regardless of the thousands of complaints Whirlpool is claiming that it is normal wear and tear for the tub bearings to fail. The manufacturer should recall the units for this manufacturing defect in the Cabrio design.

My brand new top-loading, high efficiency washer has squealed like a banshee from day one. Whirlpool replaced the main agitator part, with no success. It still squeals so loud, you cant have a conversation in the same room. Now, Whirlpool says that it is normal. No, it is not normal for a washer to squeal so loud. I am still waiting on Whirlpool to replace the same part they replaced the last time. We are still not abe to hear each other over the squeal of our new Whirlpool washer. This is not normal.

I bought the Whirlpool Cabrio washer and dryer combo with max load capacity for comforters. This is the biggest set of junk ever. Where to start? There are so many issues, starting with the fact that nothing comes clean, no matter if I even put one small item in it at a time! The fabric softener dispenser is a joke. It runs straight through into your unwashed clothes before the cycle even begins. The dryer never gets the clothes dry on the first cycle. I find that I will rewash the same load of laundry 2 or 3 times and still not be clean and then dry same load 2 or 3 times. I wish Whirlpool had these shoved up their **! Never again will I buy anything by Whirlpool!

We bought our washer in on 2011. Within a few months, the washers behind the screws on the top began to rust. Now less than two years after purchasing this high efficiency and expensive washer, not only are all the washers rusted on the plastic lid but behind the the lid and the side of the washer is rusted. Very disappointed and recommend that you do not purchase this machine.

This microwave is one of the best Ive ever used. Ive had several brands from generic on up and this one takes the cake. Its very reliable. It works excellent and heats up fast. Ive had no problems with it working to full capacity or any fear of it breaking down. Its pricey but well worth the cost if you want worry-free warming and cooking.

I should have read reviews prior to purchasing the Washer and Dryer. The washer sucks big time. Does not clean clothes. Leaves soap in clothes. The repair man said use 2 tbsps. of soap. Still soap in clothes. I use 1 tablespoon of HE soap. 2 1/2 hours for 1 load because I have to use deep water and extra rinse on first wash. Then I wash again with no soap. I HATE this washer. Whites are now yellow after washing. Cannot do lightweight comforters. I am at the laundry mat more than using my new washing machine. Dryer is ok but does not remove any lint from clothes or towels. I always trusted Whirlpool. Not anymore.

I have had repairman out on two separate occasions to look at the dishwasher. It leaks. It’s unpredictable. Unless you run a full three hour cycle the dishes come out with dish soap still on them. I am very unsatisfied with this dishwasher.

Bought unit from Lowes in july 2017. Shortly after icicles started forming on the roof of the freezer near where the door & frame meet. Called authorized service repair company to have them check out. Tech knew right away what was wrong. Appears Whirlpool has the parts made in China & then assembled in the USA. China has overfilled the freezer door with insulation warping the door. This makes the door seal sag on the bottom & pull away on the right side. No way to repair. Was told they need to order a new freezer door.Weeks later I get a call that Whirlpool cannot get a door replacement!!! Said they will give Lowes a store credit. The floor model at Lowes has the same defect. When Lowes ordered a replacement unit they opened the packing & found that this unit has the same defect. I am replacing with a Frigidaire! Where is the quality control at Whirlpool. Anyone at Whirlpool who puts these units together could not help but see this defect - but ignores it & ships it out anyway. Thats what you get from farming stuff out to China. No excuse on Whirlpools part. Maybe Trump can save Whirlpool.

We bought a Whirlpool front load about six years ago. We have had nothing but trouble with since we have owned it. First, the sensors went out on it. We had to pay over $300 to have that fixed. Then, it wouldnt run right. We had to pay another charge for that. Now they tell me the water valve is bad on it. If I had known at the time the problems I was going to experience with this washer, I would never have bought it. I fell for the price. We paid for it. We should be getting better service from it than we are. I could have bought 6 regular washers for what I paid for this one that doesnt perform like it should.

I do not use my oven much, mostly to heat up something. I noticed all of sudden I couldnt get the microwave to work at the same time as the oven. Then the controls stopped beeping. Then I went to heat up the oven and it started smoking and had a terrible smell. I am two weeks out and still no microwave or oven. The repairman was very nice. Came out and ordered parts. I wanted a new oven and I was told no. Parts came in. Repairman came out and nothing worked. Waiting, waiting and waiting. I will never ever purchase a Whirlpool appliance again. This is not my first bad experience with them. I thought maybe they got better but that did not happen.