I have been extremely dissatisfied with the Whirlpool Cabrio washing machine!!! I tried to take it back and Lowes would not let me return it because I had had it for 6 months. It doesnt put enough water in the machine to get all of the clothes wet. It doesnt get the clothes clean and it leaves some kind of lint residue all over dark clothes. I am only able to put in 1/4 of the clothes I put in my Maytag washer which I loved, but it wore out. I am also short and it is so deep I have to use a stool to get up on to reach into so i can reach the bottom of the machine. Even though it is a huge tub, I can only put a few pieces of clothes in it to get it to clean the clothes. It is a very poor design and needs to be recalled!

First, let me say we are so lucky and blessed to get home in time to prevent my home from burning. My Whirlpool range, model 4rf364pxk0, apparently decided to turn itself on (no one home) and grew hotter and hotter. It obviously burned out the thermostat because it was way hotter than cleaning mode. The key pad was melted and sagging inward the control panel warped, heat pouring from it. The racks and interior were glowing orange! My back splash tile blackened and cracked! The oven door locked! Oven hood ruined although it probably saved my cabinets! We hit the breaker! There was so much heat you could feel it on the outside of the exterior wall of the house 30 minutes later! The clean up to my kitchen has been horrible. Black soot and strange greasy film on everything and the stench has been toxic enough to give my husband a raw throat and myself a migraine! Oh and here is the ironic part - my husband was bringing me home from a hospital stay from high blood pressure! It would be almost comic if it wasnt so darn scary! Please, please address this issue before a more tragic story is posted! From looking at this site, it is obvious that there have been other incidence of your stoves turning themselves on and uncontrolled heat. I firmly believe another few minutes and our home would have been engulfed in flames. Now I will spend my weekend shopping for a new ceramic range, hood and tile!

We purchased a Whirlpool Gold Induction range, model#WF1910H0AS0, from Lowes Home Center for ~$1700.00, about 1.5 yrs ago. One night my wife was cooking dinner on the stovetop and she heard 2 loud pops and the whole cooktop went dead. We had Bobals appliances repair look at the range and they gave us an estimate of $800.00!! to replace the module board. The repairman said the module board had shorted out and burned. Thankfully my wife wasnt electrocuted. I contacted Whirlpool customer service, they said, There isnt anything they can do. The warranty is only 1 year. I also contacted Lowes customer service. They told me the same thing as Whirlpool, nothing they can do, 1 year warranty, etc. I have the part# of the module in the stove, W10390743, serial#31811552. After an internet search, this part # had been superseded, which tells me Whirlpool knows they have a problem. These ranges need to be recalled. I plan to contact the US consumer product safety commission to initiate a recall. Please inform consumers if they have this Whirlpool induction range with this problem, to also notify the Consumer product safety commission.

We moved into a new home in December. We purchased the home too late to choose our appliances or upgrade over what they install. From the start the oven has been aggravating in both the noise that it emits and the variance in actual temperature. We have had the Appliance Service out twice for these ovens. We are told that the noise which sounds like a wind tunnel is normal. It is there to keep the circuit board cool especially during the cleaning process. The noise is quite aggravating and is amplified throughout our open floor plan to all parts of the house.The temperature variance has been calibrated to be more accurate, but Im not convinced it is on the right temperature yet. I continue to give it a try, but Im not sure if the noise of the fan in the oven is making me feel negative towards using the oven at any time. We hate to have to replace these new units with another set of double ovens, but I doubt if I can continue with this noise much longer. It will definitely not be a Whirlpool or KitchenAid double oven of any sort.

I bought a 6 year warrantied Whirlpool hot water heater Model N50T61-403, product number 0733318, at Lowes Home Improvement Center and for three years the pilot light fails to stay lit. I have talked with Whirlpool 1-877-817-6750, the number on the unit, many times. I went through the troubleshooting checklist and verified all requirements. I paid a plumber $150 to check it out and he said I needed a larger supply line and venting the closet door would help. I did this and pilot still goes out periodically. Whirlpool sent me a new gas valve and it cost me another $150 to have it installed. The plumber said everything is good. But the pilot is still going out. Called Whirlpool again and talked with them for 24 minutes. The woman on the line was telling me I needed a certain amount of oxygen for this 40,000 BTU model. She was giving me minimum requirements for square or cubic feet of house with 8 inch ceilings. Yes, she said 8 inch ceilings 4 or 5 times as we went over the requirements. I got so frustrated asking her what she was talking about and she hung up on me. I called back and asked for a supervisor and a different woman had me hold on, came back and said a supervisor would call me. I did get a call back and the supervisor wanted to send me another gas valve and a burner assembly. I told him the burner assembly is working fine and I have a new gas valve. I asked him to send me a $150 along with it to pay the plumber. He said they only warranty the parts. So, am I supposed to have $450 in labor plus my time in this product on top of the original cost? I said no thank you and asked him if he would accept this as a solution if he were the customer and he said this is not a personal discussion. I know his answer. I am never buying a Whirlpool product again. But now I need to buy a new, good brand, water heater to replace the Whirlpool piece of junk. Bad product, bad company, bad warranty. I got screwed by Whirlpool once but never again.

First the ice maker stopped making ice and then the freezer stopped freezing. The unit is 2 1/2 years old. Whirlpool wants $1800 to repair! No Way. Purchased a Samsung and hope I do better with this one. So little to be praised about this American brand.

Whirlpool Gas Water heater purchased from Lowes in 2012. Have replaced two thermal couples and three gas control valves. Will not stay lit! Problems began within six months of purchase. Third gas control valve quit functioning today and Im on my way to Home Depot to purchase a Rheem...Im done with Whirlpool!

Although we live in Canada, we purchased our slide-in oven at Sears Roebuck in Buffalo, NY only because of the size availability only in the US (actually, the unit was manufactured in Canada as we found out later!). Obviously, this created another problem since the unit was not underwritten by Canadian Electric codes, Sears Canada repair would not touch it! Once installed, it worked great until the first problem with the oven quitting after self-cleaning. It is the second time in 3 years that both the thermostat and the sensor went in this RBS245 slide-in oven. Once the self-clean cycle completes (quite smelly!) and cools, the oven does not operate rendering the oven useless. First time, in 2009, Sears repair only suggested (since they would not do repair on it for reasons stated above) which parts could be faulty: Timer, sensor, thermostat or elements. It was thought to be the electronic timer unit, which was replaced at a $215 (needlessly) because that was OK. Both thermostat and sensor cost $150. Even the elements were replaced, $52. The second time, just a week ago, exactly the same happened. I replaced the 2 items: Sensor and thermostat at a cost of $154 and the oven worked fine again. I called both Whirlpool US and Canada, but no one could/would give any answers why this happens.So far, it cost $600 in parts to repair! This is nonsense from a company that has had good reputation and record. Obviously, that is changing! If Whirlpool cannot engineer a product that works as they say it does, they should close the shop! Reading here, there are others who complained with the same problem. It is time for Whirlpool to come clean!

Whirlpool Cabrio HE washing machine - I was very excited when buying this product. It never really washed clothes thoroughly. I kept getting strange stains on them and even after emptying it as soon as it finally was able to finish a load without saying UL constantly... the clothes would stink. Im sick I ever bought it! Plus, it rusts terrible.

Lost two freezers of meat in this Whirlpool. Changed Motherboard twice. Wouldnt keep ice cream frozen. Tech told me I was buying cheap ice cream. Was told by Whirlpool that they dont replace freezers. Received a call from another WP rep who did replace it. Waiting 4 weeks now because trucking company wont come up my driveway in snow. It was here once out. Driver didnt know how to change unit out. Waiting for exp driver now.

I just bought a house with a Whirlpool Accubake wall oven and after I did a self-clean, the oven quit working. It goes through the motions of working but neither element heats up. After replacing the elements ($95), I am going to replace the thermal fuse to see if that cures the problem. Whirlpools automated Customer Service phone service sucks. You cant talk to anyone about troubleshooting any problems so you spend money until you eliminate all possibilities.

I originally brought this to the attention of Whirlpool on February 27, 2014, and they chose to ignore the matter I raised. I am appalled at their customer service, but then again, customer service has been dead in America for decades now. I purchased a KitchenaAid (Architect Series II, Model KERS807SSS02, Ser. XW4704146) oven in 2009, which included a 5-year extended warranty. The first time I had to use my extended warranty was the first time a pot overboiled and thus overflowed covering the top of my range. Since then, Ive had to have my oven serviced two other times, but resulting from a pot which overflowed on the range.The controls are located in the front, directly below the stove top. There is most definitively a flaw in the design of the model I purchased. It seems quite obvious to me that the design should have included protection from moisture reaching the controls. It is very common for pots to overboil, from time to time, and thus overflow, but this should not cause the controls to malfunction due to seepage. Had I purchased the model that had controls behind the range and controls above the cooking surface, moisture would never reach the controls when a pot overflows. It should not cost hundreds of dollars each time a pot overflows on a range. Had I known that the oven model I purchased had a design flaw that allows moisture to reach the computer controls of the oven, I would have purchased the oven with the controls above the cooking surface.I invested over $2K on this oven because having owned KitchenAid appliances in the past, the KitchenAid brand had historically proven reliable. KitchenAid (or now Whirlpool) can no longer take pride in the quality of their products, most likely relative to the loss of manufacturing jobs in the U.S. Whirlpool ignored me the first time I contacted them on this matter and most recently today when I was told that it was a use matter. Apparently they believe that an overflowed pot is not a common occurrence on a range. I wrote directly to Jeff Fettig, CEO of Whirlpool and he has chosen to ignore me.

I have to say I am taking the time to write a review for my Whirlpool Cabrio Washing Machine since Ive never been this dissatisfied with a product. Every time I wash my brand new expensive black dress pants, I have resulting white marks all over! Im so upset! I washed one load three times with no soap at all just to remove the marks present! At this point, I will never buy another Whirlpool product. =(

Bought new. About 3 years old. Been repaired 2 times. Will run about 10 minutes, drain, and stop. Does not clean dishes. Model #du1015 xt xs2 Whirlpool Quiet Partner 1. Never will buy Whirlpool again.

Top loading Washing Machine Model #WTW4950XW2 - You would think that a big company like Whirlpool would make quality washers. NOT! Our top loading washer bought in late 2011 has been making loud noise during the washing cycle for the last 6 months, and last night was struggling to spin. Seriously, with just my wife and myself using the washer once a week, this washer should last over a decade! So I called Whirlpool and explained the problem... and, as expected, they cannot help me as it is over the one year warranty. NO MORE WHIRLPOOL BRANDS FOR US!

I purchased a Whirlpool French door refrigerator (model #WRF736SDAW12) with the bottom freezer last year. From the day it was delivered, its been broken. It was pouring so much water from the top panel, it would run over the top shelf and fill the shelves below. This was not a small drip. From the beginning, I was calling and requesting a new refrigerator this one was obviously defective. Whirlpool insisted on sending repairmen over and over and over again. I kept calling. I did not want this refrigerator. What if they finally fix the water problem and down the road, it has an electrical problem because of the amount of water it was internally leaking? Well, guess what? Not even twelve months in, theres an ELECTRICAL FIRE in the refrigerator! Thank goodness it was contained within a metal box within the fridge. It otherwise could have burned my house down. The refrigerator has finally been deemed irreparable. So for almost $300, Whirlpool will send a new refrigerator. Am I crazy? Theyre going to charge me more money? Its for depreciation, they said. Ive used the refrigerator for a year. I said it was broken when it was delivered. I requested a new one then. Theyre the ones who kept replacing parts. Now Im supposed to pay more money for a product that I paid full price for? I was told I have 14 days to accept their offer. WORST, customer experience, EVER! Thats what their customer service line is called – customer experience line. Sheesh!

New Whirlpool Refrigerator makes roaring noise like a broken engine. Whirlpools 2 technicians listened and confirmed but said that as the refrigerator works they can do NOTHING about it. Whirlpool management would not respond to repeated requests. Dont even get near ANY Whirlpool products!!!

We purchased our Duet in July 2010. It worked great until two weeks ago when the washer sounded like a 40-year-old washer. The bearing sounds like an extremely high-pitched “wrr”. We can hear it in the back of the house. I looked online to get parts and noticed that you cannot replace the bearing. You must replace the entire rear drum ($358.00). This does not include the labor. I talked with a technician, and they said the whole drum must be removed, not a one-man job, and to take the whole thing apart. Now, theres no price for installation. Lets go low ($200.00). Probably more. I cannot get a price nailed down without a visit. Now add those together ($558.00), I could put almost $600.00 into a washer that this could happen to in another 2 years. Wow.We had a washer that lasted us 15 years without any parts. Is there anything that you can do to help me? This is totally outrageous. Please help. Thank you. This was part of my chat to Whirlpool. Whirlpools response was I understand your problem but cannot help you. It is out of warranty. No help, no discount, nothing. I will and have all my friends never to purchase Whirlpool. This is from a so-called American company. Im very disappointed.

Purchased a Whirlpool Cabrio washer WTW5800BW0 September 2014. Two years and 8 months later it no longer works. Call Sears and Whirlpool and was basically told I should have purchased a warranty. Whirlpool tried to sell me an extended warranty for $495.00 which is about 80% of the original sale price of the washer. Was told it is my responsibility to care for the maintenance of my purchase. WOW. Way to stand by your product. So now its my fault they sell a product that does not last longer than 3 years. So we tried option 2 - called a repairman. His response save your money and buy a new washer. WOW. A repairman rather lose money than try and fix this washer. Save your money and pass on Whirlpool products.

I have a Whirlpool dryer for about 8 years. The lint catcher has some holes so I called the 1800 phone no. that I got from the dryer and order the part. That happened in May 18 - I pay for it. I have been told that I will receive the part in 5-7 days. Today, Aug. 27, I called see what really happen with my part. Well I have been transferred from a department to another. I waited over an hour on the phone. No employee can find my order in the system and hey keep on telling me that I did not order! In the end, the order have been found. They told me that the part has been in the back order and I will receive it on 9/12/2014 - 3 weeks away adding up to 4 mo since I order and my credit card was charged. I cancelled the order> I really do not want to deal with Whirlpool ever again. I am happy to pay for a new dryer - some other brand and put in the garbage the Whirlpool - for a lint catcher and bad customer service.

Its a front loader and has lots of cycles and temperature to choose from. Its setting on a pedestal so its not too low. I dont like the way the soap is dispensed.. If you still have the door open when you pour it in the dispenser it almost comes out on you. It also knots your clothes up and makes them hard to get out. The rest is good.

Whirlpool Gold Class Refrigerator is not quiet 4 years old. Starting at about a year old, I had to start defrosting the freezer periodically because the freezer coil would build up ice to the point where the fan would start rubbing on the ice and making a loud noise. Then about a year ago, it started leaking water from somewhere around the water filter. The water damaged my cabinets and flooring. Then the freezer slowly started to warm up. I had a technician look at it and he determined the compressor is bad. That would cost about $900 to fix, according to him. I thought it had a 5 year warranty on the compressor and associated parts. Whirlpool is claiming this is not true. The repair costs will not be covered. I paid almost $3,000 for this refrigerator! Didnt last 4 years and caused thousands of dollars in damage to my cabinets and flooring! I will never buy another Whirlpool appliance! Buyers beware. Stay away from Whirlpool at all costs!

When we remodeled our kitchen after checking a lot of brands of oven we decided to buy the Whirlpool Self Cleaning stove/oven. Loved the look of it. When trying to clean the oven I followed the directions just as its said in the manual. After the cleaning was complete it didnt even look like it clean the oven. I called customer service and they told me I had to clean the oven with a little elbow grease before I put the self cleaning on? Really? I have to clean the self cleaning oven by hand beforehand? Why did I purchase a self cleaning oven then? And because it was just 2 weeks out of warranty they would not help at the 800 number. NEVER NEVER again will I ever purchase Whirlpool! How they treat their customers is disgusting!

We bought the Gold Series Whirlpool fridge (Model WRF990SLAM00) in December 2013. A few months after its first repair, (dripping on the top left inside of the fridge), which happened within the first year and was covered by the manufacturer’s warranty, it started to make an incredibly loud whirring sound that kept us up at night. Our bedroom is upstairs and far away from our kitchen, and I had to sleep with earplugs to not hear the noise. We tested the noise on a decibel app and it came in between 66-70. A normal fridge noise level should be around 52 decibels. We had a repairman come out and he replaced a fan even though he told me it wasnt going to fix the problem. Wait, what? After he replaced the fan and the whir continued, we called Lowes extended warranty again, and they sent out a different company: 1-800-Appliance.The second guy replaced two kits and found some issue with the ice maker, which we were not even aware of, but the noise remained, and he then had the gall to say it was a normal noise. If it was normal, wouldnt it have been making that noise the first year we had it? We had 1-800-Appliance come out again and he determined he couldnt fix it, so Lowes sent another guy from the same company, and he replaced the same fan that the first guy replaced, which was clearly not the problem. Three perfectly good fans were wasted. BTW, the repairman who said the noise was normal told us that the fridge had a part that was made to be replaced after purchase because if Whirlpool had the part at the point of sale, the fridge would not meet the Energy Star standards. Hello, lawsuit! After three repairs for the same problem and five visits that did not fix the problem, we were told Lowes would issue us a return order in three days. Finally!Not so fast... one week later, no one called, so I called them and then Lowes denied having told us that! We gave them the name of the person who told us they would take the fridge back, but the woman on the other end said she had no record of that (how convenient) and, despite the California lemon law requiring only three attempts at a repair, they would require yet another attempt by one of their repairmen. She told me that if he determined the noise was abnormally loud and not repairable, then she could contact the manufacturer and go from there. So they sent a guy from the first company out and he wrote down that the fridge was not repairable and was very noisy. He said that should take the fridge back at that point.My husband called Lowes several days later after not being contacted by them and they told him that they need to send a different repairman out from 1-800-Appliance and that only 1-800-Appliance could determine if we could get a refund. If that was true, then why send the other company out? By the way, the second guy sent out by 1-800-Appliance wrote down that the noise was very loud and wasnt fixed by his repair. But the notes Lowes said they received from him didnt say that at all. They told me that he wrote that the noise level was normal. I am starting to think there is collusion between Lowes and 1-800-Appliance. Something very wrong here. So, six visits later and horrible customer service from both Lowes and 1-800-appliance, we are now being told that the repairs need to be 30 days apart from each other before they will issue a return.If the cause of the noise was never actually repaired, then why do we have to wait a month between repairs? We continue to jump through the hoops that Lowes keeps throwing our way, but it is now clear that they have no intention of taking the fridge back. The fridge is less than two years old, and we have the extended warranty. We couldnt take the noise any further because it felt like it was causing hearing loss and after several months of that horrible sound we were both on edge, so we bought an amazingly quiet fridge from Pacific Sales, and they assured us that they would not do to us what Lowes did. Pacific Sales pride themselves with having good customer service. Lowes seems to have taken delight in lying to us, selling us a lemon, and then not righting a wrong.We have moved the loud piece of ** into our garage, and if Lowes continues to change the rules of a return and act in collusion with 1-800-appliance, probably in hopes that we will simply throw in the towel, then at least we dont have to hear that horrible sound in the meantime. If they dont do the right thing and take back the fridge, then we will simply keep calling out a repairman to fix the problem. We have three more years of our warranty, and if Lowes doesnt do the right thing, we will make them pay for this one way or another. Viva la revolucion!!

The stove is okay except it scratches on its glass surface fairly easy with the non-stick pans. Also wished it had a self-cleaning oven. Its not the easiest to clean on the inside of the oven. The knobs are easy to use but its hard to navigate knobs to low to keep food warm rather than cooking at a low temperature. It has strong exhaust fan that really does its job.

I bought a compact washing machine and 4 months later it broke, needed a CCU board. To make a long story short now the machine is 7 months old and still broke. Whirlpool cant locate a part for it nor do they want to replace it. I think its time to get a Lawyer involved. Ive been calling for weeks now and have gotten nothing but the run around from all very Rude employees. Im turning this over to a lawyer. Im done dealing with Whirlpool. For a large corp Im very aggravated and severely disappointed with them. Wish I never bought their appliances. NEVER AGAIN.

I bought a pair front loading washer & Dryer May this year and took Delivery in June. First problem was with touch controls. I should have Known then it would be trouble, they replaced it then we went home to Fl. - Aug. Returned in Oct - used the machine eight times total and it locked up with our Clothes inside in water. Called for service, was told it would be a week before someone could come, then was told after four days it was the mother Board and it would take at least another week to get our clothes out. Their Service is the worst I ever have dealt with. The whole house - we Bought Whirlpool based on the Maytags we bought for our House in 2004. Never a problem but those Maytags were Maytag - not whirlpool. I would never buy any Whirlpool Appliances again. It is sad because I try to buy American made to support our fellow Brothers and sisters in the work Force but now I will buy made anywhere as long as it works and has reasonable service. Whirlpool is not the same as I Remember from years ago.

I purchased this Whirlpool Cabrio washer three months ago from hhgregg. If I hit the lottery, the first thing Im going to do is take it to the dump and buy a new washer. There is no way to wash a load of towels in this machine. I started a load at 7:35 this morning and it is now 9:53 and Im still dealing with the drain and spin cycles. Over and over, I try to get it to spin out enough water that I can put the towels in the dryer. I should have suspected something when I saw that the washer even had a separate drain and spin cycle. It should have told me something. Its a piece of junk. Never again. Im back to Kenmore.

I purchased a Whirlpool Microwave on 9/21/10 from Hamilton-Bryan in Wichita Falls, Texas. I had a small fire in my microwave on 9/19/11, due to a faulty mica board. This was replaced by Mr. Bobs in Wichita Falls, TX, under the warranty. Then on 1/9/12, the microwave would not warm anything. I called Mr. Bobs again, and they said the transformer was out. I called Whirlpool, and was told by Yvonne that Whirlpool would replace the part only, with no labor, but Mr. Bobs was closed, and to call back in the morning, so this authorization could be set up with Mr. Bobs. I called back and there was no record of my call with Yvonne. I talked to a supervisor Rachel in Tennessee. She put me on hold for a while and finally said she found Yvonnes note to authorize the part. I explained to each person I talked to that I was dissatisfied with Whirlpool. I believe I have a defective microwave. I would like my money back, or a new microwave. I believe the defective mica board is related to the defective transformer. I am a very dissatisfied customer. I have used Whirlpool most of my adult life. I have used them since the 1970s. I currently have a Whirlpool refrigerator, washer, and dryer. A similar situation like this occurred when I bought a Samsung washer. I was dissatisfied, and Samsung refunded my money, and I bought a Whirlpool washer to replace Samsung. I will not be satisfied with this situation, until the microwave is replaced. Thank you for your concern and attention to this matter.

I have been having a problem when washing my jeans in the Whirlpool Cabrio that I have never had before with my old washer. When I wash my jeans, there are always a few pair, never the same ones, that have an odor like dirty dishrags on them. I always hang my jeans to dry so I do not think it is this. I have tried to add a freshener to the wash cycle, it does not work. I have tried to dry them in the dryer with a scented dryer sheet, it does not work. I am assuming after reading these past complaints from other consumers that it is not getting all of the clothes clean because of the lack of water. I always use the deep water cycle, but maybe it is not enough water as previously suggested. I have had an issue with blankets and other heavy items not getting clean and/or not even wet. Thoroughly disgusted with this appliance!! I love all of my Whirlpool kitchen appliances though!

WTW6340WW0 - When washing clothes, on the last spin it stops and gives an UL error message. I make sure all the clothes are level and restart at that point but still the UL error message appears and water starts leaking from the underneath of the machine. Weve reset the and unplug the machine but no difference. Please help on what else to do.

My refrigerator & dishwasher were purchased less than a year ago. Ive already had all the doors replaced on the fridge and the new ones are rusting. Discovered same issue with the dishwasher. The company doesnt seem to be overly concerned with remedying the issue. No sense of urgency or concern for the customer.

I love a refrigerator that keeps my milk and water ice cold and keeps my fruits and veggies crispy and fresh without freezing them.

I purchased a side by side Whirlpool refrigerator in December 2009. In one year’s time, all of the plastic shelving has completely broken. The repair man said that he felt like the plastic was substandard and to call Whirlpool but they said that we must have abused the shelving.I and my husband are senior citizens and the only ones using this refrigerator. How can all the plastic components break within one year? I had my last refrigerator for over 10 years and I gave it to my son. It is still running and all the plastic shelving is still intact.I feel Whirlpool should fix this problem but they do not care about their customers. Once they have your money, you are forgotten. In the end, they will be forgotten because I advise everyone I know not to buy from Whirlpool.

Whirlpool Cabrio Platinum washing machine: You wont believe this until you call a parts replacement place for tiny part. The plastic (or vinyl) lid hinge bearings are located at hinge corners of lid. Hinge pin passes through them, one on each side. Half the size of a penny, UNCONSCIONABLE greed at the price of $32-$33 dollars EACH when ordered from a parts place. IMHO, design by INTENTIONAL failure to fail after three or four years. As a result, the lid will not stay up on its own. Then you find out the horrible news which is an insult to intelligence. Id have expected to pay maybe two or three dollars each, but NEVER the price they are demanding. Theyve got you and there is NOTHING you can do about it. At that rate, parts would run tens of thousands of dollars to replace the entire machine, part by part. These greedy clowns make car dealers look like reasonable people! The LAST Whirlpool machine of ANY kind we will EVER own!

We bought our washer in on 2011. Within a few months, the washers behind the screws on the top began to rust. Now less than two years after purchasing this high efficiency and expensive washer, not only are all the washers rusted on the plastic lid but behind the the lid and the side of the washer is rusted. Very disappointed and recommend that you do not purchase this machine.

I like Whirlpool, but the ice maker never worked right. Now l have to clean the ice off the dispenser about every three days. Other than that has been good. This is my third Whirlpool refrigerator.

My glass stove top broke for the second time. The first time Whirlpool accused me of dropping something on it and chipping it. I didnt but paid the $400 glass replacement. Today while cooking, I put cold from the fridge not freezer, sausage into a warming fry pan. I heard the same pop I heard 2 years previously...sure enough the glass stove top broke. After a phone call to whirlpool, and hearing they were sorry but theres nothing they can do, I will write as many letters I can so others dont buy whirlpool.

The microwave keypad is worn down after 10 uses making it difficult to read the pad. I just discovered the microwave was missing the front leg and they do not have a replacement part so I am stuck with a virtually new microwave that will not balance. It took 4 phone calls to their customer service department to try and sort out the problem. Poor product and extremely weak customer service department.

I bought a Whirlpool/Fridge Freezer Model WRF560SMYM 01, less that two years ago. Two months ago it started making a terrible noise. Apparently the freezer was iced up and a mechanic defrosted it. It happened twice more and he left saying he could not fix it. Another arrived and took the model number and he disappeared. A third the same. Now I have an empty freezer, just an ice maker. It seems to not freeze up so quickly with the moisture control on. Over $2,000 down the drain unless somebody can fix it. Oh and the fridge gets very cold! Does anyone have any ideas apart from throwing it out and buying another? Never another Whirlpool!

I had an upscale Frigidaire suite of kitchen appliances and I loved them. A few years later I moved and needed a new set. I thought Whirlpool was about the same and I bought a Whirlpool set. The stove wont boil water or even fry an egg. It heats up and cuts off continuously. I called a service rep out and he called the engineer who told him it is designed like that and I need to use hot water on the stove to boil it. I was shocked at his ignorance and insulted by his stupidity. Ive been cooking for 60+ years and everyone who cooks knows you use cold water to boil water. But really, the stove does not cook anything. When frying eggs the burners cut off every few seconds to the point you cannot cook anything with it and the engineer said thats the way they designed it. DONT BUY WHIRLPOOL. THEY WONT EVEN BOIL WATER. HORRIBLE STOVE AND ONCE YOU HAVE IT YOU ARE STUCK WITH IT.

Just purchased a new Whirlpool Counter Depth, French Door, Freezer on bottom, Refrigerator from Lowes. Delivered Sept 1, missing the flap that makes the seal between the two doors. Shelves can be seen inside the fridge with doors closed. Exposed wires on the side of the door in a port with no cover. The fridge is unusable. Cold air flows out between the doors, temperature will not go lower than 45º. Moisture build up on the top and dripping down through the fridge. Frost build up on the back. Refrigerator runs continually. Had to shut it down. Called Whirlpool Sept 2. They will not replace the defective product. I must wait for a repair. The promise was within 24 hours for a technician to call. Called them Sept 2. Local family operated appliance repair company did not receive the request until Sept 4. They do not have the part nor does the parts supply company they deal with. Its on back order. Whirlpool has the part but long weekend and it will not be here until Sept 8 at the earliest. Whirlpool has advised Lowes that the issue is dealt with. I will see the technician on Sunday (Sept 6). Small family Business does not operate on Sunday or holiday, Monday, and have advised Whirlpool of this multiple times. Whirlpool doesnt care. I paid $2700 and do not have a working refrigerator. I will never purchase another Whirlpool Appliance.

We purchased a Whirlpool dryer almost three yeas ago. Its a front load, steam dryer--or WAS should I say. Almost a year ago, I was unable to calibrate the control panel (in other words, to change the cycle). Ive been advised by the tech that I need a new control panel $200. Really Whirlpool??? A $500 dryer that lasts two years?

I bought the WTW4815EW0 Whirlpool washer. Worse machine ever! It’s take forever to wash a load, there’s no way it’s efficient when it takes twice as long to wash one load. It doesn’t sense the water level correctly, Its noisy, and after only having it 3 years it crashed on me. I refuse to waste money fixing the piece of junk and when I go to purchase a new one it won’t be a Whirlpool.

We bought a Whirlpool model WFW5620HW front-load washer at Lowes. The unit shook so violently during part of the spin cycle that the Whirlpool-authorized service company technician said not to use it while parts were ordered. It seems the balance ring was not functioning. Parts ordered were shocks and tub assembly. The technician suggested trying to get a whole new unit, as the repair is so intensive he had only done one or two in his career.Whirlpool customer service said they would not replace the unit, and an escalated request had the same response. I think this is terrible customer service - when there is such intensive failure in the unit, they should provide a brand new machine. The work has not yet been done - we are without use of a washer for an unknown period of time, since the order of a tub assembly is so uncommon that they do not have a time estimate. Needless to say, we will never buy Whirlpool again, and suggest you do the same.

We purchased a new Whirlpool Cabrio Platinum W10405142B washer and dryer just over 3 years ago. We decided to go back to the top load as we were having so many issues with odor from our front load. We purchased the set at a Sears store in Timmins Ontario and we’re quite confident that we were getting an excellent product. From day 1 we have had issues with having to rewash our clothes. We have lint and white streaks on the clothes as if we were using powdered detergent and they are all tangled. We have always used HE liquid and at one point I switched to soap nuts to get rid of using chemicals. We have now changed to pods and still have issues. When the washer is spinning it is deafening. You can hear it outside for goodness sakes. It sounds like it is about to take off and fly.The cycles are ridiculously long. For a quick cycle the other day and a very small load it took 72 minutes... how is that quick? When the wash is done my clothes are all tangled up and are stretching things out of shape. I am careful what goes in my washer and how large my load is. I know not to wash sheets or towels when I am not home as they will eventually be unbalanced and have Sat all day in the washer only to have another hour of washing when I get home. We are currently doing some work in our home and pulled out the washer. The floor has a rust circle from God knows what. I will attach a picture. The lid not longer closes. I have to hold it down until it locks and it still pops up a wee bit.I do not understand why I am responsible for purchasing a new set when the product I bought should have lasted and not caused damage to my clothes or my flooring. How do we as consumers make the manufacturers responsible for things like this. If nothing else the appliances should be removed from my home by the Company and I should be reimbursed for damages and the cost of a new set. I will continue to look for my receipt as I keep everything and I am unsure what is meant by order #.

We purchased Whirlpool dishwasher Model #GU3200XTXB Nov. 2011. Two weeks later they replaced the soap/rinse aid dispenser because the rinse aid was running out the bottom of the dispenser. Feb. 2012 they replaced the handle which was loose. July 2012 the panel lights werent working and that was replaced. Feb. 2014 the soap dispenser door would not open, so the dispenser was replaced again. March 2014 the soap door would not open again so the computer board was replaced & the door did open. However, it stopped again 3 days later. April 2014 the dispenser and the board were both replaced. The rinse aid dispenser did not dispense leaving the inside with moisture on everything. So yesterday the dispenser was again replaced but now the rinse aid is running out the bottom of the dispenser. Thank goodness we purchased an extended warranty for $169 or we would have spent more than $1,000 on repairs!! The warranty company refuses to acknowledge that their lemon law should apply. There are 2 of us and we use it 2/3 times weekly.

My Whirlpool oven (Model WFG505M0BS0) stopped working - the bottom oven part (the top burners were OK), the display on top functioned normally, but no fire came on. I called Whirlpool, and then I accessed Whirlpool online and scheduled service with their official service representative - Flamingo Appliance Service ** for September 9, 2020. When the repairman arrived on 09-09-2020, he opened up the stove and checked it, and he told me that a computer part needs to be replaced, as well as the igniter, and the cost would be between $400.00 and $600.00 (I dont remember the exact amount), I told SEVERAL times, maybe its just the igniter (for which the cost would less than $100.00 AND already included in the $134.95), but he insisted that the computer needed to be replaced, I did not like the way he explained it to me, it did not make sense.After that I was planning to buy a new stove, as the repair was too high. But, I decided to try to change the igniter myself before getting rid of the stove (the igniter cost was $21.00). I just got the igniter recently, and installed it, with help from YouTube, and what do you? THE STOVE IS WORKING!!! This is fraud!!! FLAMINGO APPLIANCE SERVICE ARE THIEVES, AND BY ASSOCIATION, WHIRLPOOL, WHOM THEY REPRESENT ARE THIEVES ALSO. I shall publicize to the best of my abilities: NOT TO BUY WHIRLPOOL PRODUCTS!!! This was not a mistake!!! This is the way they rip people off!! Either by paying exorbitant amounts for unnecessary repairs, or by buying new appliances when the old ones are still good. Dont buy Whirlpool!!! Dont use Flamingo Appliance Service. Theyre both fraudsters.

I purchased a washing machine and dryer 1 year ago. Since then it has started to get spots on the control panel where you select size, temperature, etc. I also purchased an extended warranty through Home Depot and is still under warranty for 3 years. I was told for a few more days is still under man warranty. I contacted Whirlpool and they said it is not their problem and sounds cosmetic - I think this is unfair being that I spent a lot of money and it has started appearing on the washer and dryer. No one wants to be responsible. I am a consumer who is very careful and have not had any spills or cleaned it with anything.

We purchased the Cabrio Whirlpool washer from ABC Warehouse October 18, 2014. They said if we purchased a washer of higher quality it would last longer. We have bought Whirlpool washers for over 40 years. When our last one only lasted for three years they convinced us to spend more money over 1000.00 witha purchase of a 5 year warranty 6 days over the warranty. It is junk. The bearing went out costing 600.00. They graciously offered to sell me another washer. WOW, everyone is sorry that we have this problem BUT you are out of luck. Are they kidding? I will never buy another Whirlpool. They use to be the top of the line but now I feel we are in a throw away world and talk about consumer rip off. FLEECING OF AMERICA AT WORK!!!!

I have had my Whirlpool electric oven for so many years that I don’t even remember when I purchased it. I also have a Whirlpool stove top & the same with it. Zero trouble for many years. I highly recommend Whirlpool range tops & ovens.

Purchased a brand new Whirlpool hot water heater, but it has never worked properly. The 1-800 help line has been no help at all. Every call results in another step we have to complete before they can fix the problem. Bottom line - never, ever, ever buy a Whirlpool product. They dont know the meaning of customer service.

My whirlpool duet was extremely quiet the first few times I used it and seemed to work well. Then I noticed that it randomly drained the clothes but didnt spin them, it did it on different cycles, and I would have to run the load again on spin and drain, another 19 minutes of run time. After a week it began to make metal scrapping sounds on the spin cycle and vibrated to the point that it moved the pictures on my walls. I called Whirlpool customer service and they authorized a service call. In short, the service man was very confrontational told me there was nothing wrong and charged me $72. It still vibrates and randomly doesnt spin. But now after he took it apart it sounds like a jet engine when it does spin. Whirlpoolss response after repeated calls? Not a new machine, but another service call......

I purchased a Model WRF989SDAB01 Whirlpool refrigerator with the French doors and had it delivered in March 2014. The evaporator developed a refrigerant leak in May 2015. Whirlpool said it was not their problem since it was over a year since I bought it. The technician said this is a problem with this model. I am having it repaired under the extended warranty that I bought. One of my concerns is that the unit has two evaporators so the other one will probably start leaking any time. What a piece of junk. Dont buy Whirlpool. Their quality and service stinks!

We purchased this Whirlpool refrigerator at the end of July 2018. At the beginning of November 2019 all the interior lights went out at the same time. We called the store where it was purchased, and they instructed us to call Whirlpool. Because a year had passed, they were not willing to do anything other than put us in touch with someone who could service the refrigerator. We already know the repair will cost over $200. That does not include payment for the service call or the labor. At almost the same time we purchased a new Whirlpool microwave. We have also had problems with that. My advice is to stay away from Whirlpool products if you want something that will last longer than a year.

The dishwasher is less than 2 years old, out of warranty, and will not start. The repairman said the problem is in the electronics. It would cost $500+ to repair.

The first Front load Whirlpool washer leaked. 5 repair techs visits. Wasted days. Finally located the leak, in the main basket. Replaced washer. Second washer the clothes come out smelling like a horse blanket. Mold. Clean the washer every month still mold. Plan on junking the washer a getting a new model. Never expected this much trouble and time on a basic appliance.

This started Sept 27 2017 when the ordered online electric range 30 inch slide in oven Whirlpool brand was delivered. When using the oven, a noxious diesel smell filled my home, despite multiple attempts to burn in the unit as advised. 10 days later after still trying to burn it in fumes got worse. I called corp who then sent over a tech to look at it and the tech shared with me when he arrived that he was the wrong person since he cant smell due to an old injury! He admitted he smelled a chemical when it first went on but it went away for him but might have went away due to is impaired smelling ability. I called Corp back and they totally agreed something was wrong with it that could not be repaired and the unit should be picked up and I should be paid back that day it is picked up. They said in a few days which later turned in 2-3 weeks out and counting... I filed a complaint with the BBB due to the ongoing issues. Corp office said they would pick up unit and at that time hand deliver me my refund in full. At first the pick up was weeks out but after BBB was notified they came yesterday 10/18/17 and removed unit, but no check! I called Corp again this time asking why I did not get my money as they promised she said someone dropped the ball, and that someone should have told me that since they had to get someone non-local to get it that they will mail me the check in 14-21 days! She said I see in the notes. They told you they would hand deliver you your refund so they should have called you about the change.So here I sit... No oven in use since Sept 18 and no money back to buy one for weeks yet. I have never been told, despite my requests as to what the chemical was that I was burning off in my home and exposed my family to over 10 days which we had headaches and nausea from (despite windows opened and fans going at full blast). Only that it might have come from the manufacturer or process. This company isnt the only one who has had issues on occasion with a defect in this never-ending chemical smell but the lack of regard of my safety concerns and failure to stand up to what they offered to do (poorly handled response) is simply wrong and bad business. I have not dealt with Whirlpool regarding matters ever and have very little of their products in my home so unsure if this is unique or standard with them. I wont buy their products anymore because I am less than very dissatisfied with my experience. I may have been the only unlucky person having this kind of response from this company but felt the need to share.

I bought my Cabrio Platinum Washer and Dryer in 2013 (4 years old). About a month ago, it started sounding like an airplane was landing in the house while on spin cycle. I called a repairman and he said the bearings were going bad and it would be better to buy a new machine. When we pulled out the washer, there was grease all over the floor - apparently a seal started leaking and the bearings had no grease so they started burning up. I talked with Whirlpool, after all it was only 4 years old and a seal leaking and burning the bearings up wouldnt be from normal wear. They were not convinced and offered to give me a discount on a new one -- No Way! I went with another brand recommended by the repairman. The screws on the dryer door also came out and we had to replace them. So much for the Whirlpool brand and especially their top of the line machines. I will not buy another Whirlpool washer or dryer.

We bought a Whirlpool freezer-bottom 18.5 cu ft. fridge from Lowes. The compressor broke in less than three months of regular use. I called Whirlpool who sent A&E to check it out. The technician didnt even file a report and lied to me about what was wrong with the fridge. They sent a different company to come look at it and they confirmed that the compressor is broken. I called Whirlpool customer service and was told that the warranty only covers repairs not replacement even though I paid over $1,000 for a defective product. The excuse: Its a man-made product so we cant guarantee it! So what used to be a 3-5 year warranty not too long ago is now what? A one-year warranty is virtually useless. I can see a future not too far off where there is no warranty at all. Where is the protection for the buyer? If I wanted to purchase a second-hand fridge, I would have. I will never buy Whirlpool again.

We bought a Whirlpool gas range about a year and half ago. The oven started giving lighting problems we had to light with a match every once in a while. Then the broiler igniter started giving same problems so I replaced the igniter, still did not work. Then I tried the control panel, still nothing. The igniters were about 45.00 each. The control panel was 250.00. Then I replaced the spark module and it is now working. Some models the spark module dont control oven and broiler but mine does. That was 200.00. The best thing was the part place I was ordering from would exchange the parts that you try and they also can answer questions either online or by phone, Appliancepartspros.com. My oven model # is wfg371lvs3.

I bought a Whirlpool Cabrio washing machine from Lowes 3 short years ago. Within the first year, it needed a new main board. Now just 2 years later, it needs another main board. It has never worked correctly. I have purchased another washer from another manufacturer and will never buy a Whirlpool product again and neither will anyone I talk with about this. Dont buy Whirlpool products!!

Cabrio top load HE washer - Ive only had the washer a couple of years. My husband bought it for me thinking it would make washing more time efficient and energy saving. Lesson learned! After struggling with this washer for the past year, I was told today that to repair it, it would cost around $800 or I would need to buy another washer. The washers bearings and tub need to be replaced and it will not spin properly or at all. Previously, I have owned washers for over 10 years each. This was definitely not a good purchase. After reading all of the other complaints on this site, I understand that I am not alone. It was also mentioned on one complaint of the possibility of a fire hazard with this washer. Whirlpool should be recalling.

Purchased a Cabrio large capacity washer. It NEVER seemed to get the clothes clean enough, and after the sensors and bearings went bad within three years (out of warranty of course) I gladly kicked it to the curb. I bought a Samsung that has been great. Id like to support USA made, but not when it is AWFUL.

17 month old Whirlpool duet washer door lock broke. ($300) repair! Had given my old (13 years) set to daughter when I moved. That set has never had a repair or problem! Why do they keep making things with more bells and whistles we dont need and so cheaply made? Frustrated, annoyed and becoming cynical in middle age.

I bought a whirlpool washer because we thought it was the best. It does not clean our clothes especially my husbands jeans. They are on their third wash at this minute. I use Gain HE detergent. I bought clorox 2, I use spray & wash & I have even started using a little clorox but the red dirt still doesnt come out. I never had this problem with my old washer. If there is any help for me here please let me know. If this is supposed to be a water saver I dont see how I have saved any after washing jeans for the third time. If they are not clean this time, I guess he will wear them dirty.

I purchased a Fridge/Freezer just over 4 years ago. It was an expensive one. The gas is gone and they cannot re-gas it. If I was told this when I was purchasing it I certainly would not have spent this money. I rang the concessional team. They would give me nothing towards a replacement as they had not one in stock, POOR Service for a big company. I am in business and this is not the way I would treat my customers. This has certainly turned me away from purchasing Whirlpool Products, despite having a industrial washing machine and Dryer. For the record, I had 2 servicemen to check it and they were most pleasant. It was beyond repair.

After 2 months of owning this fridge (Whirlpool Model WRF993FIFM) it started making a horrible buzzing noise that you could hear all around the house, both ice makers stopped working, and it wasnt cooling properly. After three technician visits, and of course having to miss work to have the technicians come to my house, my fridge still doesnt work. The most recent visit today was from 2pm until almost 8pm, yes seriously 6 hours, and now the noise has gotten even louder and my ice makers still dont work. AND after the tech left, my carbon monoxide detectors were going off for almost an hour. We had to open all of our windows and sit outside to not DIE of carbon monoxide poisoning. So beyond livid with this situation. Its been a month since Ive had a properly working fridge. Whirlpool needs to do right and fix this situation. I will be calling tomorrow first thing.

Contacted this am. See through top glass lid is separating from plastic causing sensor to turn washing machine off. Looked complaints up on this machine and it is a common occurrence and is a defect. The machine is a little over 2 or 3 years old and out of warranty. Was told not a common occurrence and I would be responsible for repair. Model # wtw7800xw2. Serial # c12270139. Thank you.

I have a Whirlpool AccuBake gas range. I started by contacting my local repairman because my stove was out of warranty. The first company came out 3 times and replaced three parts, which didnt work. The cost was $297.00. I originally paid $598.00 for the stove. After they deemed it non-repairable, I contacted Whirlpool. They basically said it was my fault for not buying the warranty. I then contacted the BBB. Anne ** from Whirlpool contacted me and had another Whirlpool service tech come out at no charge to me. But guess what, they deemed it non-repairable too. Its a shame that companies no longer stand behind their product. Its very apparent that this is a manufacturers defect. They should replace the stove.

We have owned refrigerators for over 40 years. Never had one as bad as this. Three ice maker replacements lasting maybe from 6 months to 2 years. Cap that off with customer service people who by voice and tone could not give a rats ** about helping the customer. Today it took me from 3:10 pm to 5:30 pm to get a real person on the phone. When I did the attitude is so reminiscent of a fast food hamburger joint with arches. Yes they know the refrig and ice maker are and have been a problem but they don’t care cause we have no option. Whirlpool will NEVER SEE ANOTHER penny of my money. Time to look at real appliance makers. Horrible.

I just purchased a brand new home. I have an electric wall oven with the microwave over the oven. They are both built into the wall. Can anyone tell me why a massive amount of steam is coming out. It is really bad it makes my microwave glass so bad I can see through it. It is also making my cabinets so wet I have to use a towel to dry them. Plus I got a steam burn. Can someone tell me if this is normal.

I had noticed water on the floor and just thought someone left the freezer open. It started happening about every other day. I read online that it was probably from the drain in the bottom on the freezer being clogged or frozen, and I found instructions on how to fix it. After we took the door off, the drawers out, and the back panel off, then we started thawing the drain. Finally, I got it cleared out. Here I am, a month later, there’s water on the floor again.

Ice maker stopped making ice. This side by side Whirlpool refrigerator was purchased 4 years ago. We called Whirlpool. An authorized repair man identified the problem. At the bottom hinge of the freezer door two of the wires have been broken. A defective design, but no recall from Whirlpool. The solution is to replace the entire freezer door for a cost of $1200. Ridiculous that a replacement door cost more than the purchase price from Lowes. It would appear that these 2 wires could be reconnected, but Whirlpools only solution is an entire new door. Automakers stand behind their products with recalls, but its not the same with Whirlpool. Love my Whirlpool range, washer and dryer, but this counter depth side by side is a real loser.

Have had this washer for one year. Clothes have never been clean since day one. Dark clothes come out with white marks all over. Having to use an extra rinse cycle or set on bulky items - whats the point of a high efficiency appliance? Still not clean after that anyways. Stains such as chocolate and toothpaste still remain after washing and my husband complains of finding small holes in his clothes. Lid needs to be left open at all times or you get a funky smell. I am using the HE liquid detergent, even tried a cold water product for cold washes. I hate this washer. Wish I had my 20 year old Kenmore still.

Owned it for approximately 15 years and has never had any problems with it all. I would highly recommend this product because it is affordable and easy to care for. It even comes with a filter for water. Great refrigerator.

Purchased this washer 5 months ago. Have had service 3 times as dark clothes come out with white residue. I have done everything possible to correct the problem. They recommended from cleaning the machine, using less detergent, minimizing the load, using extra rinse, deep water and still the clothes come out with the residue. And it takes way too long to wash a batch of clothes. This is a known problem with this model. Repair company recommended a replacement and Whirlpool insists that it is a usage problem. One thing they said Could be water is too cold, I live in Florida there is no cold water! Whirlpool refuses to replace it. DONT BUY IT!!!

On November 1, 2011, I purchased the Whirlpool Estate washer (model # ETW4400XQ) from Wholesale Appliance in Charleston, SC. The first time I used it I knew something wasnt right when both the regular and so-called gentle cycle agitated at an incredibly fast speed. It is damaging my clothes. I called the dealer and they sent out a service person. He said that was just the way it was and he couldnt do anything. So, I keep trying to use the gentle cycle, but it was the same thing. I would have to stand by the machine and stop it after a couple of minutes so it wouldnt ruin the clothes. The more I thought about it, I decided that the repairman wasnt right. I called Whirlpool customer service and they sent a different repair service. He also said that he couldnt do anything to make it slow down as it was programmed by a computer inside and he could not change it. I went to the dealer, Wholesale Appliances, and they said there was nothing they could do as far as giving me a refund or a discount on a better machine. The setting on the washer clearly says gentle cycle.” Well, the whole world knows that does not mean beat the clothes to death as fast as possible. Can you make any suggestions? Thanks.

It started getting warm and wasnt getting any warmer. Model number ED2VHEXV001 22 cubic feet side by side. I read another review and it sounds just like mine, OMG. It better just need something, its less than three years old. I am not happy and I always bought Whirlpool, my first trouble with it.

Purchased 11-02-2016. This Whirlpool/Kenmore dishwasher is falling apart. Top rack wheels are totally broken, ordered parts 4 times, gave up. Now they are held together by gorilla glue. I have gone through 3 gray plastic end caps for the top rack runners. Now one is contained by a plastic slip tie. Last week it started leaking. Sears was totally useless. Whirlpool keeps sending me back to them. Now, I have to go buy another new dishwasher. It will not be a Whirlpool. Next time getting the extended warranty.

The Cabrio washer does not efficiently clean clothes! The clothes have a type of lint on them after washing, and our sheets have an odd discoloration that stays on them even after drying. We have a max. capacity washer/dryer, & we dont overload. Plus, we use the recommended detergents and the amount of detergent as directed. Fabrics dont even smell clean.

First F1 symbol on washer took 6 months to resolve. All we needed was new motherboard and couldnt mail it to us even though we could replace. It had to be an authorized person. Well we had one and they never put him in the system. Finally got that taken care of, 6 months of having to press pause and restart 5 times just to do one load. Arrrrrggggghhhh! Now water leaking out the bottom. Called again, on hold, then on hold again to be transferred to tech support. Yeah, right. No tech support. Talked to management, they could care less about us even though we have other products from them. Dont buy, they are lemons. We had ropes for 15 years and lasted through everything. Thanks Whirlpool, heres to losing a customer!!!!

I Purchased 9 year warranty, Whirlpool water heater and installed it. Started having problems in the first month. It started giving a water temp too high error code, yet water was barely warm. Called Whirlpool. They had me do a bunch of diagnostic checks. Determined it was a bad control module. Sent me a new one. I installed it. Within a week or two, same problem. Called Whirlpool. This time they sent a Tech out. Everything on water heater tested normal, nothing wrong with any part. The tech finally, found a TSB that indicated that you couldnt have any re-circulating valves or systems connected to the water heater. We had one to keep hot water at the taps. So I removed the re-circulating kit and water heater worked for a few months. Then same problems, it keeps going into error. Error code indicates water temp too high, but water is barely warm to cold. Call whirlpool several times, they send out another control module and heating elements and I replace them. All work temporarily. Finally replace control module again, and it works for several months. Then back to error codes. Not always the same code. Sometimes it is water temp too high, other times it is check one of the heating elements. We have lived with it like that for about 3 years. We get hot water by resetting the water heater several times a day. Well, about 3 months ago it started tripping the circuit breaker in the electrical panel. I called Whirlpool and explained what has been going on since I bought their piece of junk. They will not do anything unless I call and pay for a service tech to come diagnose and repair the problem. They will provide the parts for the repair. I am not a certified appliance repairman, but I do handy man repair work for a living and do appliance repairs quite regularly. I am capable of doing every test that the repairman will do, but Whirlpool insists that I pay to get their defective product repaired. Then if I have problems again in a couple of months, I will have to pay a service tech again. I have friend that had this same water heater. I replaced the control module on his once. I was telling him about my woes and he told me he got fed up with all the problems and ate the cost and got a new water heater, not a Whirlpool. I am going to call Whirlpool one more time and then I am sure I am going to do what my friend did and put the money I would spend on a service tech into a new water heater. It will not be a Whirlfool.

I bought the Whirlpool Cabrio washer and dryer combo with max load capacity for comforters. This is the biggest set of junk ever. Where to start? There are so many issues, starting with the fact that nothing comes clean, no matter if I even put one small item in it at a time! The fabric softener dispenser is a joke. It runs straight through into your unwashed clothes before the cycle even begins. The dryer never gets the clothes dry on the first cycle. I find that I will rewash the same load of laundry 2 or 3 times and still not be clean and then dry same load 2 or 3 times. I wish Whirlpool had these shoved up their **! Never again will I buy anything by Whirlpool!

The washer works well for the age of it. However, I would say it is not designed as nicely as some of the others I have seen. I found it performed okay doing the wash, but it didnt hold up as well I as I would have liked. Seems cheaply made. The machines plastic parts have stained from rust and seem tinny.

Purchased a new Whirlpool washer and it has the sensor-- like I am too stupid to decide on the level of water to match my load-- not sure why I got an agitator because I am the only thing it agitates. The clothes just sit there in its own filth and then go in the dryer. Actually put a stained item in the wash to remove the stain and instead it just spread to other clothing and has stained and possibly damaged them. Washing the same clothes 3 times is not saving energy, water and time for me.

We have had our dishwasher for over ten years and have had no problems. Its been very reliable. Its a free standing unit on wheels with a butcher block top as we dont have room in the cabinets for a built in. All you have to do is roll it over to the sink and plug it in and hook up the water line which has a quick disconnect. The male half always stays on the faucet.

Whirlpool Cabrio - Worst washing machine I have ever had. Unbalanced when washing sheets, towels. It does not matter if one sheet or two. I will never buy another one like this again. I would be better off having a twin tub for the amount of time I spend in the laundry to fix this machine when it bangs, bangs because it is unbalanced. HATE, HATE, HATE it.

We bought Whirlpool duet front loading washer and matching dryer. In 3 years the water level seemed like it was off. Clothes, especially towels were coming out stinky. Eventually you could hear the clothes were merely flopping around wet. Before we could order the repair part it completely quit and locked our clothes into it. I washed my clothes at my daughters house for a week and dried them at home. Within the week the dryer quit. Not having the money to repair both machines, my son gifted me a set of top loading washer/dryer. Again Whirlpool. In a week we had repair service out. They replaced everything possible and it still didnt work right. Since the 90 days from purchase was approaching we returned it to the store and they had Whirlpool send us a brand new dryer. This one worked for a month then stopped spinning. I havent called for service yet because now with 3 broken machines I am so disgusted. When I think about them I feel like I am going to puke. My washing machine shouldnt be the worst thing in my life, especially since it was a lovely gift from a wonderful son.

Whirlpool Duet Washing Machine model WFW9150WW02 - This machine was purchased new in Sept. 2011 along with a brand new dryer. We started noticing a rumbling sound within the first year, but both machines did a fantastic job on the laundry. Then last week, the washing machine didnt spin out a load of laundry. We called the company and they scheduled a service visit through A&E Factory Service. The technician immediately diagnosed the problem as a bad bearing and said that he had seen the problem frequently with this model and put it down to a design defect. The bearing is housed in a stainless sheath protected by a rubber seal, but the seal lets water in, which rusts the bearing. The cost to repair it was over $700. He suggested I call WP and ask for a concession, whereby the company would at least pick up all or part of the cost of parts. The service representative summarily dismissed the request, saying the company had no obligation to stand behind the product as the machine was out of warranty. I said that this was unacceptable. She was pleasant, but kept asking questions and putting me on hold. Ultimately, she said the same thing. Whirlpool was once a dependable name, no more.

Purchased our Whirlpool Gold Oven in October of 2013 from Best Buy. The oven works fine, but using the oven to make pizza on March 30th of 2014, a fire started in the drawer under the oven. The oven was set at 400 degrees. Several oven mitts were stacked in the drawer. There was no major damage done to the range, other than a bit of discoloration to the white trim, but we will never put anything in the drawer under the oven and would advise others to do the same.

We purchased Whirlpool AquaLift oven from Lowes 10 months ago. Since then, I dread each time I use the oven because I end up cleaning it by scrubbing and using different products because AquaLift cleaning is a scam. I have arthritis in my joints especially my neck, so cleaning it by sticking my head inside is a nightmare for me. I will try to call the company and see what is going to happen. I read that someone is suing Whirlpool for this product so hopefully they will recall the product or refund us if we return it.

The American Standard 95% 2 stage variable furnace is by far my favorite furnace to install. I know exactly what to expect from this furnace and I have had zero factory issues with this model. Outside of making a few sheet metal transitions this American Standard standard 95% furnace was very easy to install as well. And like the 2 stage variable … no factory issues.

We purchased a WRS576FIDM refrigerator from HHGregg in August 2015 and immediately had problems with ice maker and door having condensation on it. I contacted Whirlpool who had a tech come to my house and verify problems. Whirlpool replaced it with a new refrigerator in November 2015 and w/in a week it had awful condensation on the outside of the door, dripping onto the floor and pooling water. A tech responded to our house again and confirmed the problem with Whirlpool. Whirlpool advised they would be sending out two new doors for our side to side refrigerator and said we should receive them within 4 to 6 weeks from late November 2015. I asked Whirlpool to send us a different model because this is the second refrigerator of the same model that has the same issues. Whirlpool refused. I have spent countless hours on the phone with Whirlpool, HHGregg, and waiting for service appointments and my patience is getting thin. I just contacted them today 2-9-16 to inquire about my doors since it has been well over the 4 to 6 weeks Whirlpool said it should take to receive them. The Whirlpool rep on the phone had no information about the status of the doors and said that they would have to contact the service company to inquire more about the status of the doors. He also said that under special circumstances, it may take an additional two weeks for certain door orders. I once again requested a different model of refrigerator or a refund.I tried to get HHGregg to allow me to return the 2nd refrigerator just days after I received it since I was having the same issues as the original one I purchased. HHGregg said they could not since the 2nd refrigerator did not come from them. HHGregg said that they did not know why Whirlpool sent me a replacement refrigerator directly and added that normally the returns go through them. I feel like I tried to do the right thing by contacting Whirlpool for warranty work, but I feel that if I would have called HHGregg I would have been able to get a different brand refrigerator which is what I really desire after all these problems with the Whirlpool brand. I did purchase an entire Whirlpool kitchen set from HHGregg. The only problems I am having is with this refrigerator.

We bought a Whirlpool Gold French Door refrigerator in 2010. Just when the warranty period passed, the refrigerator started leaking water from the bottom floor. Initially, it only leaked about once per month. But as time passed, the refrigerator started leaking more often, and now its leaking every 2-3 days. I saw many people complaining on the same problem and some of them even submitted since 2006. I dont know why Whirlpool doesnt resolve this issue in many years.

Update on a report filed last 4/19/2012 regarding a Whirlpool side-by-side refrigerator. I originally described the issue as a fire in the relay/compressor which destroyed the compressor and relay. I eventually called Whirlpool and they agreed to send out a technician to perform a repair free of charge. The Whirlpool authorized repair person replaced the compressor and relay, recharged the system and all is working as it should be. Whirlpool covered the repair even though the refrigerator was manufactured in 2003 and I purchased it in 2004.

I’ve had the dishwasher for at least 3 yrs. if not longer. I have a long history with Whirlpool products and so far I haven’t had any problems with my past purchases. They normally wear out from age because if you take care of it normally they last for years.

I love the look and performance of my Whirlpool Dishwasher. It could be a bit quieter, but overall I have no complaints. My washer was already installed in my home when I purchased it and I must say, it helps when the family gets together and you don't feel like washing the dishes. The dual chamber pod holder is great if you need to use and the heat function works wonderful. I don't have the problem of the left over water that a lot of dishwashers leave behind and no spots!

I paid about $400 for this dishwasher and the regular price was over $600. Got a good deal. It washed dishes wonderfully. All I had to do was scrape the chunks off. It cleaned the rest. BUT... at a certain point, it started NOT cleaning. It was only about 6-7 months old. It was to the point where everything just came out kind of slimy and food grit was re-deposited on the dishes. I cleaned both filters. I made sure there was enough Rinse-Aid all the time. I ran hot water in the sink before starting to make sure the temp was hot enough. My husband went online and someone had instructions about cleaning the water intake because it could sometimes have sediment buildup. Not a difficult process, but there was no gunk in the intake filter. When I listened to a load it seemed like it drained, (most start with that), paused, rinsed for a couple minutes, paused, drained, paused and refilled for the wash cycle. So the pump worked, the arms went round and sprayed. Nothing was in the way of the arms. After it started the wash cycle, it seemed to just stall. It would spray for about a minute and then stop. Im not sure it sprayed after that. The timer kept counting down. It said dishes were clean, but it was an absolute waste of time. I was ready to go buy a cheap dishwasher and throw this one in the dumpster. I think it is a 720 padm??Just after my husband checked the water intake filter, we started another cycle. When it was rinsing, he opened it up and everything seemed to be working ok. It drained, then filled and started the washing cycle and then stopped. He opened it back up and surprise, the water was full on the front level by the float (that turns the water filling off). But in the back of the dishwasher, there was only about an 8th of an inch of water. Online it said the water should fill to just about the top of the heating element. It WASNT. Problem? It wasnt LEVEL. The instructions when installing said it should be leveled. We did when installing it (when it worked great). But looking back, we put in a new hardwood floor about the time it stopped working ok and we didnt put 2 and 2 together. We did not re-level. When we pushed the dishwasher back into its built in cabinet, it must have gotten OUT of level.The rinse part worked I guess. Then it drained and re-filled. After re-leveling the dishwasher, we opened the door at that point. The water was a level depth front to back and side to side. My husband explained what he thought had been the problem to me. When the wash cycle starts it fills, the float shuts off the water at the appropriate level. THEN... the dishwasher starts to pump and fill the arms and the tube up the back that feeds the upper washing arm. So much water goes into the arms and up that tube, the dishwasher looked almost empty of water again. As the dishwasher was now level, it began adding water to compensate for the arm/tube filling. Before the float would shut off too soon because the front part of the tub was full but the back wasnt. Without enough water, the dishes were NEVER going to/COULDNT get clean.The re-leveling made sure that the float didnt turn off the water filling until there was much more water, the CORRECT amount. The next load cycled all the way through, spraying much more than Id heard before and the dishes were clean. P.S. I also got some dishwasher cleaner and used that on a couple empty cycles. I NOW LOVE this dishwasher again. FYI If my husband wasnt handy Id have junked this thing. We HAD leveled the dishwasher when we installed it. Just didnt realize it COULD get un-level just pulling it in and out of the cabinet to install new floors. Check out all the troubleshooting stuff in the manual. But if it doesnt help, put a level inside across the bottom rack, front to back and side to side and make sure the bubble is in the middle of the two lines.The previous dishwasher I had, just made like a fountain of water that went up the middle of the dishwasher into a sort of funnel filling the upper arm. THIS one has that tube up the back and it curls down under the filter and Im guessing it is more sensitive to being OFF LEVEL, because the tube doesnt go straight down, it curls and lays across the bottom of the tub. Without being level, there was never enough water to suck up that tube to start the the actual wash cycle and it just stalled there till the timer said clean at the end. IE: dishes never did wash. BUT IT DOES NOW! Woohooooo!

I purchased 5 Whirlpool appliances when I moved into a new home approximately 5 years ago. The selection buttons on the plastic panels on the front of 3 (dishwasher, washer and dryer) out of the 5 appliances has either broken completely through or are in the process of breaking through, leaving an ugly appearance on the front of the appliances. When inquiring if I could replace these panels, I was told that one (dishwasher) would cost me $100.00. I believe that the structure of these panels has been extremely poorly manufactured. Why would you put perforation around each button? It is obvious that they would push through. What can Whirlpool do for me?