I purchased a Whirlpool Cabrio set 3 years ago based on their brand reputation and consumer reports. It has been a terrible experience since the moment the warranty expired. First, about 1 month after warranty expired, I had to replace the main electrical board. Then about 3 weeks ago, the drain pump failed. I purchased the $110 pump and installed it myself. Now this week, the spin cycle sounded like a jet engine. I took it apart to find that the bearings were shot on the drive shaft. I figured, well it is just a wear item, understandable right? So I went to order parts and got told that I have to order the whole outer tub for $250 with shipping! For some bearings! I called Whirlpool directly and was given no explanation other than Call some parts distributors. They may be able to help you get the bearing separate, but we dont do that and there is nothing that we can do. Amazing. I equate that to having a faulty brake on my car and being told that I have to replace the whole axle!Fortunately, the washer never really did a great job. It was loud and tore clothes up, so the decision to part ways was not too difficult. I have the list of brands they make and will be sure to never buy another. Im selling this one for parts. Im sure there are others out there that will need a pump and control board soon!

Very unreliable oven. Oven temperature never seems to get to the proper setting. Do not buy any Whirlpool appliance. They do not stand behind their product. A stove should be relatively simple but Whirlpool managed to produce a product that is complicated & unreliable.

Bought the hot water heater, installed it. It leaked from bottom. Whirlpool warranties it. Replace it with new heater. It too leaks. I Google problems with Whirlpool hot water heaters. Found over 1500 complaints.

Purchased Whirlpool side by side June 2010. Within a few months realized major problem with ice maker. Reservoir on door would leak and freeze inside the door. Service man out at least twice, advised to maintain service contract as would continue to have issues. It still leaks, freezes up and does not dispense properly. Now the inside liner of the refrigerator is cracking and neither the warranty company nor the WHIRLPOOL Manufacture Co. will stand by their product. It is my intent to warn as many people as possible, so they will not have the same bad experiences.

We bought our Whirlpool refrigerator model # WRT318FZDB02 July of 2019. We liked it very much. The beginning of January 2022 we started having issues with things freezing. A few days later nothing got cold. The appliance technician that checked it out said our seals on the compressor were bad and needed a new one. He told us we were better off buying a new refrigerator. I contacted Whirlpool support and they told me the same thing. Our previous refrigerator lasted over 30 years!! I would think Whirlpool would make their refrigerators last longer than 2 1/2 years!!

Washer MOD WTW4800XQ2 - I purchased this washer about 2 years ago after my 15 year old washer died. I have always used Whirlpool appliances as well as my Mother that recommended Whirlpool to me some 40 years ago. I knew when this machine was delivered and set up that I was in for change. It locks down to where you cant get in it for too long of a period of time. I am a really busy person, and HATE this, but if that were the only issue, I could accept that. We live on a farm and our clothes get really soiled especially in the warmer months. I like to pre-soak white clothes, NOT happening with this machine!!! It ends the cycle after about 30 minutes so I have to start over, wasting water. But the main issue is the machine tries to level the clothes, or whatever it is doing on its own before filling with water. I wash a lot of clothes!!! I am going to say that 90% of the loads of clothes that I have washed with this machine have been off balance, banging around bad. I then have to wait for it to unlock so that I can pull out the dripping wet clothes and replace to try and get it balanced. I am 59 years old, I got married at 14. So Ive been washing clothes for a LONG time... This machine is junk to say the least. I recently house sat for family. They purchased a new GE washer and dryer a little bit before I got these, wonderful machines!!! I washed dog beds, sheets, blankets and tons of clothes during this time. WOW, I had forgot that washing clothes didnt have to be torture. I will NEVER purchase another Whirlpool product. This washer has exhausted me. I purchased it at Lowes on tunnel rd in Asheville, NC. Please, if you havent already, junk this design... Its gonna lose your loyal customers. This complaint has nothing to do with where I purchased it. I did not contact the store as they did not design the machine. I did NOT want to pay for service on a poorly designed product...

I bought a Whirlpool Cabrio washing machine from Lowes 3 short years ago. Within the first year, it needed a new main board. Now just 2 years later, it needs another main board. It has never worked correctly. I have purchased another washer from another manufacturer and will never buy a Whirlpool product again and neither will anyone I talk with about this. Dont buy Whirlpool products!!

Our Whirlpool water heater needs a burner assembly replaced. Second time within the warranty period of six years. Parts have to be ordered, so you will be without hot water for several days to a week. The worst part is reaching them. Between my wife and I, we have almost 4 hours invested in sitting on hold waiting for someone in three different calls. They never answer the phone. They give an option to call back. They never call back. Im so frustrated. No Whirlpool products ever again. Im sitting at my desk, hoping someone will eventually answer the Whirlpool line. I dont even have the part ordered yet after two days of no hot water. Who knows how many more hours I will need to sit here and listen to this music on hold. It is incredible in 2021 a company can remain open while offering this kind of customer experience.

We purchased Model # WFG231LVQ from Appliance Connections. Its a 5 burner with oven. When my husband went to clean the stove door, the bottom handle fell off because the heat from the oven had melted it brittle. Weve had this stove less than 3 months. Then we see where the clips that hold the glass on the front door have melted. The plate that separates the burner from the oven has bowed and splintered the porcelain. And the oval griddle burner only puts out flames on one side. Whirlpool sends a repairman out. He states that they really make them cheap these days. Writes down the whole list of things wrong with it. Repairman calls us back and reports that Whirlpool only wants to replace the parts. Im afraid to use my oven. I want it replaced or my money back!

My Whirlpool is almost 20 yrs now and we thought we were going to have to get a new one! New ones aren’t equipped with what mine has so after much investigating we decided to try a water inlet part for $35 delivered and oh to our surprise it is still performing like new. We bought the top of the line and it still is! Thank you Whirlpool. You are what you say you are. Arlene **.

We have an 8-year-old built-in Whirlpool Estate. It is probably as basic a model as you can get. It has been 100% reliable, and cleans the dishes well, even without rinsing. We do not buy expensive premium dishwasher detergents, either. So far, we have required no repairs. Basic features--heavy wash, normal wash, pots and pans. This dishwasher is standard (not extra large.) This is not a fancy dishwasher--just white. It is what matches the rest of the appliances. We have been lucky regarding the performance of such an inexpensive dishwasher. We paid about $250 for it.

Bought a Maytag Bravo XL Top-Loading Washer Model MVWB880BWO. It was installed on Jan 22, 2014. In December, the spin cycle became very loud. I contacted Whirlpool on Dec. 2. They said a local technician would be out on Dec 5. They make up this date. I called the local technician. They came out on Dec 16. I was informed that if there was nothing wrong with the washer, I would have to pay for the service call. The tech. found there was a bearing problem. He said they would contact Whirlpool about the warranty repair. Had not heard from the repair shop. Today is Jan 5. I called the local repair shop. They said they were waiting to hear from Whirlpool. I called Whirlpool. (Thats another nightmare). They said they were waiting to hear from the tech. The man at the repair shop said he has been trying to get a hold of the rep for our area in Eureka, CA. Apparently he doesnt return emails when he is in training and apparently he is in training most of the time. It is totally unacceptable to have to wait for over a month to have a washer repaired. Not sure what a consumers recourse is for getting something that is under warranty repaired in a timely manner. Maytag used to be a good product. Since Whirlpool produces the Maytag, the quality just is not there. Very poor service. I would not recommend buying Whirlpool. You will not be happy with their product or their service.

Purchased my Whirlpool dishwasher in 2005 model number GU2500XTPQ3. So it worked for about 10 years and I am fairly happy with that but I have a warning, my control panel shorted out putting out thick black smoke and I was unable to turn off the dishwasher. I had to turn off the switch at the breaker box. If my wife had of been the only one home she would not have known how to turn it off and would have had to call the fire department. I dont know if the short would have led to an actual fire but with that much heat I have to believe it would have. Warning, dont run the dishwasher when no one is home. Hope this helps someone.

Whirlpool Upright Freezer Model EV205NXTN01 – The freezer door interior plastic panel bows away from freezer cabinet causing door gasket not to seal. The new gasket doesnt help since the groove of the gasket mounts in bows outward with the interior plastic panel in the door. The freezer is 20 months old now and had the door replaced for the same reason at 10 months old. Now, Whirlpool says sorry it’s out of warranty. Guess they want me to buy a new door every year. I wont be buying Whirlpool products anymore as I dont need another boat anchor.

After replacing our competent GE dishwasher with a Samsung dishwasher and having to replace it immediately due to the terrible job it did, we bought a Whirlpool Gold Series (stainless tub) for just under $400. I realize this is the bottom of the stainless tub price point, but we have been so disappointed! The silverware container sites outside the regular tub, and rarely cleans even easy substances to remove, if there are more than a few items in each container. Dishes on the other levels are very hit or miss -- each and every load has to be examined for dirty dishes. Id pull this one out and return it too if it werent such a hassle. Dont buy this product.

It will constantly go off balance. I usually have to wash the cloths twice before they come clean and I have to unload washer and re-load it to get it to possibly spin without going off balance again. It will twist the quilts and fold them under themselves and tear them from the pressure. I have called after 6 months of owning this product and explained to the Lowe’s employee and they said it cannot be returned unless it was broken mechanically. This is the worst piece of crap I have ever own. The last Whirlpool product lasted 12 to 20 years. I hated this thing after the first few washings. I generally have to stop the washer and let it soak and then turn it back on if I want the damn thing to get the dirt out. I am using the required detergent as well. I will never own another top load machine like this. I am trying to unload it. Now, I have to buy another washer because I might as well take the clothes out and beat them on a rock at a creek with this thing.

Im glad to see that Im not the only one that is dissatisfied with Whirlpools products. Three weeks ago I found my basement to be flooded and you could tell that it was from the hot water heater that was installed in 2005. The plumber changed the release valve. I thought that was it. This past Wednesday I go down the basement and find another flood. The plumber said pilot was not lit. The explanation was wind could have come down the chimney and blew out the pilot. Pilot was relighted and within 12 hours there’s cold water again. I called the plumber again and said that the thermal coupling must have gone bad. I went to Lowe’s to get a replacement and found that Whirlpool is sending a free replacement but I would have to pay shipping. All well and good, but what do I do in the meantime for hot water? If Whirlpool made a mistake, why didnt they send the replacement parts to the businesses that sell their products? I guess that would be the simple solution; instead, they expect me to pay $30.00 for shipping and be without hot water. Well, let me tell you: Im tired of this hot water heater. Whirlpool can go out of business for all I care because they dont stand behind their products. Im going to buy myself a Rheem and Im sure Ill be a lot happier. Need a new hot water heater? Don’t get a Whirlpool!

We replaced our kitchen appliances and went with Whirlpool. The oven and Refrigerator havent had any issues yet but the dishwasher has been crap since it was installed. While it looks 10 times better than my old dirty dishwasher it replaced, its main function of washing dishes is 1/4 the of the quality after running two or three times. Not to mention the average cycle time is 4-8 hrs. Dishwashers by design, should be convenient and save time. Whirlpool managed to remove both of those traits from this Dishwasher and now their warranty service said they can send out a technician but I will have to pay for it if it’s not covered under warranty!

Whirlpool washing machine was not a good buy at all specially after using it and seeing that over the years I had to incur high costs of maintenance. Over the months and years of buying Whirlpool front load washing machine, I had to replace motor twice, digital display twice, motherboard twice THAT TOO at a very high price every time something broke. This time the angle that supports the drum broke and Whirlpool says drum needs to be replaced. HOWEVER, after waiting a month company says DRUM IS UNAVAILABLE. Which means my machine has become absolutely useless just because Whirlpool does not have the spare. Whirlpool has a ridiculous track record with poor service and poor product quality. Manufacturing in one country and selling it in another WITHOUT SPARES is defective and poor service, totally unreliable. Wouldnt recommend Whirlpool to anyone.

This washing machine has not worked well from the time I bought it two years ago. It never fills to the amount of water required to clean clothes, it is always off balance, so I need to adjust the clothes at least five times per load. I end up wringing my load out by hand. The clothes come out smelly and not clean. After the cycle is done all the clothes smell like mildew. The other night while doing a load, it made such a loud noise in the motor and started to shake up and down, and then moved forward, like it was going to take off or explode. I tried to do another load, but after it filled and started to agitate, it started to make a loud grinding sound and there were 25 minutes left, then the timer showed 26 minutes left, like the computer in the machine is messed up. I had to empty the water out, wring out a load of clothes including towels, exhausting.The worst part is that the machine is finally paid off, I am a single mother on a disability and I am stuck with this piece of junk. I felt desperate so I looked up Cabrio washing machines to try to figure out what could be wrong, and then I find all these negative reviews, and these owners all have the same issues. Why has there not been a recall, or a class act, who can afford to replace a $700.00 washing machine every three years. I also purchased the Cabrio dryer which cost over $700.00. I do not trust that it will be any better in the long run.I cannot rate this machine as it has been a nightmare from the start. White socks seemed to come out with more dirt than when I put them in, and I am sick of using bleach all the time, the fumes make me feel ill. This is not acceptable, obviously this item is defective, and a prominent company such as Whirlpool should take the loss, not all the victims that paid too much in the first place trusting that Whirlpool was a reputable company, I will never give them my trust or business again. I hope to hear from you, and if there has been a recall or class act legal actions, please let me know as I want to be involved.

2013 Whirlpool gold series stainless steel dishwasher, at that time it was their top of the line product, nice looking, stainless steel, stainless steel tub, very quiet. However this piece of junk does not stay fixed for more than a year, at best. I am a technician by trade albeit not on consumer appliances, I usually work on more complex multimillion dollar equipment; point being, I know my stuff.I have been throwing parts on this box like no tomorrow, Tub replaced, water director motor replaced, top railing replaced, small plastic pieces on top rack replaced. MTBF - Mean time before failure is 6-8 months and deteriorating over time. 2 issues are predominant symptoms of its failures, its either leaking or dishes dont get cleaned. I see the symptoms again and I am tired of fixing it so it going to the curb tomorrow. There is no way an expensive appliance like this (around 800$) can cost 100$ a year in parts to maintain (Note: parts only)... not to mind my labor and hassle ++ water damage to your cabinets. Stay away from Whirlpool and keep your sanity!

Worst Air conditioner brand I have ever come across. My personal experience with Whirlpool Air Conditioner is not encouraging. I have used almost all brands of AC but found that the quality of Whirlpool AC is not worth recommending. Please stay away from Whirlpool. I got one Whirlpool 1.5 Ton Split Air Conditioner (Model 3D Cool Xtreme, 6th Sense Climate Control) at my house about 2 years back. I booked a service request with the Whirlpool’s Authorized Service Centre M/s Western Refrigeration Co., NOIDA as the Air-conditioner was not cooling to the desired level. On the first visit on 20-05-2019, the service engineer advised that the AC was not cooling because the gas had drained and the gas is required to be filled for which there will be a charges of Rs 2500/-. Believing him, I agreed for refilling of the gas at his quoted price. He sent next day some other attendant team for filling the gas. Those attendants revealed that in addition to the gas, two valves are also required to be replaced at an additional cost of Rs 1600/-. Though I had a doubt about the correctness of their diagnosis, there being no option, we paid for valves also. Accordingly, a total of Rs 4100/- was paid by us.However, to our utter surprise, the AC stopped cooling within a couple of days. Hence, the service centre was again informed. The complaint was again attended second time on 04-06-2019 and we were told that they have again refilled the Gas.However, again the result was NIL. The AC was not giving cooling effect. Hence, third time again complain was booked. The first attendant once again advised for only gas filling after thorough examination. He sent an another guy on 20-06-2019 for gas filling who then revealed that the cooling effect is not there because the condenser coil is leaking and the same will have to be replaced at an additional cost of Rs 5500/-.The following important points emerges out of the above:- 1) If there was a condenser coil leaking problem, why it was not disclosed to us when the AC was attended earlier by various Service Teams consisting of various attendants in the process from the same service centre? 2) Whether my all money paid earlier for gas filling and changing of two new valves will go waste due to wrong diagnosis by your technicians?3) Keeping in view the earlier wrong diagnosis, I very much doubt the present diagnosis and feel that this is a ploy to extract more money from gullible customer who lacks technical knowledge.We spoke to the service centre officials up to three four levels on the numbers received from the call centre but after listening the matter they assure to call us back. After no call back from their side, when we try to call them, they do not lift our calls. The above facts clearly bring out the cheating, harassment and looting by the Service Centre under the aegis of the so called prestigious company M/s Whirlpool. The hard earned reputation and trust of the Whirlpool is being impaired by these unscrupulous service centre.No punitive action appears to have been taken by Whirlpool office against the unscrupulous service centre for unfair trade practices. Rather the person from Whirlpool office over call was also trying to coax us to pay some more money to the unscrupulous service centre who has already cheated us and extracted money earlier from us with zero results. My Air Conditioner is totally shut off due to mishandling and misdiagnosis by the service centre. We are acutely suffering due to scorching heat and over and above going through the mental harassment for the last two months.We expected an immediate resolution for the above problem on top priority basis without any further additional cost however despite my number of reminder through their toll free number, mail id etc. the problem still remains unresolved and unattended. It is highly disappointing that despite my writing repeated mails with reminders no senior person from Whirlpool has so far taken cognizance of the grievance and the customer has been left in the lurch to be harassed by the highly inefficient, incompetent and indecisive service centre officials who have miserably failed to address the issue and satisfy the customer.

I bought these products 2 1/2 years ago along with a dishwasher and Microwave, all which are Gold Series. The first month my Microwave broke. Instead of a certain part that they used to use, they now use a Capacitor instead and it broke. The repairman fixed it under warranty, but told me Ill be seeing you again. Then, my oven occasionally says Function not available. Whirlpool wont tell me what the problem might be and they have nothing for troubleshooting this problem in their manual. My only solution is to reset the circuit breaker and then it works for awhile. Now, My refrigerator has ice building up at the bottom of my freezer and leaking all over my floor. I found a Whirlpool bulletin online which explains that this problem is because of a defective part (Grommet) and that they have a replacement part for it and you can get it by calling their customer service department. Why didnt they send out recall notices to their customers?So, on 8/10/2015 and 8/11/2015 I tried getting this new p-trap part, but for two days now Whirlpools computers arent working and they have no other way of looking this stuff up. Very poor customer service and I also waited for a half hour on the phone to be told their computers arent working. How about putting a message on their pre-recorded message letting customers know their computers arent working?

My microwave came with my house. I didnt choose it but it has been a great brand. I love the preset timers for defrosting & for popcorn. Its big enough to handle an 8x8 pan which was important to me. The turntable could be more stable. My model is a built in over the oven option. Black & digital. It has lots of preset options & is pretty user friendly. I like the size & it is super quiet.

We purchased a Whirlpool Cabrio washer & dryer in 2005. After CONTINUED issues with the washer during & after extended warranty, we decided to replace it in 2011. Im not a fan of mismatched sets, so we also replaced the the dryer. After researching the WP Cabrio, we assumed that model was a fluke and reluctantly replaced with the Whirlpool Duet Set. Nearing our warranty expiration, our new washer has stalled for the 3rd time. Sears customer service has been absolutely dreadful since day 1. Original delivery was scheduled incorrectly, so we ended up picking it up. We then spent the next 3 months trying to get our military discount credited back. They promised at time of purchase it would be credited automatically. After 2 hours wasted on the phone today, we are still without a working washer.. or even a date as to when it will be repaired. I was appalled at the condescending phone conversation I had with Sears rep. When service showed up last week, he knew immediately that 1 part was missing. He replaced the other 2 parts, and assured me hed rush the 3rd part and come back out today. Had I not called, we would be receiving a phone call on Friday to say our part was backordered and not available until June. After a long and frustrating conversation, I was told we could have a courtesy $25 max a week for laundry, with a max of $100 per year. I was also told that it wasnt Sears fault the part wasnt ordered when I called the 1st time, and so the 21 day wait period didnt start until the service man caught the mistake. If we hit 21 days from that date, they supposedly will do some sort of swap. I have confirmed with WP that the part is on back order, and frankly they didnt do anything either.. but the rep was much more apologetic. They couldnt do much because our warranty is through Sears and not them directly. My great niece is coming in 2 weeks for the 1st time since she was put on hospice, and I will be without a washer to clean her cloth diapers. She is on a very specific diet and has a feeding tube, so I will have to waste time hand washing clothes instead of savoring her visit. I will never shop at SEARS again. They have continued to go downhill with all the corporate changes. I left the corporate world a couple of years ago, and I can tell you that Sears doesnt take no or sorry from their vendors. Im very upset and intend to take this to another level, which I rarely do.

I bought a house with Whirlpool appliances and I bought the extended warranty for all the appliances, I started to have issues with the refrigerator almost 4 months ago and still waiting for results, do not buy whirlpool products, every time you call the warranty department be prepared to spend at least one hour waiting for a customer representative. Buy LG or GE instead. These are excellent brands that I have owned in the past.

I purchased a new Whirlpool Cabrio washer and it has been nothing but a headache. The machine constantly rips our clothes and stretches them beyond repair. Now, the washer keeps showing an F1 error code and I have to restart the machine three times to get it to start. It also stops in the middle of the cycle and I have to restart it. What a piece of garbage! I called Whirlpool several times and they do not stand behind their products. Do not buy Whirlpool. I filed a complaint with the Attorney General and I suggest anyone else having the same problems should do so. Maybe we can get this machine recalled.

Outstanding, however our location has a hard water rating and as such we have to use a deodorizer to balance this out. A wide range of variables which are a fit for my purposes. Interior dimensions and layout are more than perfect for my uses. This particular dishwasher is built in so blends aesthetically into the design of the kitchen seamlessly. The product has a drying system which successfully blows air over the top tray to eliminate wet areas within depressions of crockery, glass, and so forth, its excellent. There is also a light steam setting which removes tough deposits from surfaces.

Whirlpool washer Model WGD4815EW1. Bought this washer just about 4 months ago and right away I hated it but was told by people that all the machines had gone to the lid lock and that the government had mandated the energy saving devices on the machines so the machine will only put just a little water in the machine. I have been VERY VERY unhappy with this machine. My husband figured out a way to bypass the lid lock mechanism. Then after washing clothes many times I found out in order to get my clothes clean I had to just set the dial to Bulky every time OR I had to wash the clothes 2 times to get clean if I didnt. Once we bypassed the lid lock and then I figured out where to put the knob so the clothes would come clean I was fine until last week the machine just would NOT wash or do anything... it filled with water and just sat there until my husband got the water out. I located a Speed Queen from an appliance store and I am much happier. It does not have the CRAZY lid lock on it. I realize that some children are apt to mess with the washers. But I dont have children anymore and when I did I had a laundry room with a lock up high on the door so they could not play in the laundry room. I dont understand why this so called mandate could not have been done in a way as to allow those with kids to have the option on the machine with a built in code device to set the machine so the lid will lock and those of us without children in the house to opt out of the code to set the lid lock. NO REASON why we cant have a CHOICE. As far as I see it is a way for the government to try control more where they need to keep out. The cars have been designed with safety locks for children to keep them safe, but it is up to you to choose to use them. Same principle! Now for the mechanism to make it so the machine will only put so much water in the machine to wash. Youre NOT SAVING any ENERGY or WATER if you have to wash the loads twice!! This whole mandated business with the newer washer machines is a huge JOKE on everyone. I will be searching out used machines and having them rebuilt because I dont EVER plan on buying another one of these newer machines. If enough people stop buying them the manufacturing companies can raise some cane with the government to get the mandate lifted. NO I will not buy another Whirlpool washer. I encourage some of you out there who LOVE a challenge to figure a way to change the stupid motherboards on the newer machines and create a great business for yourself because if someone else can create it you can recreate it.

I purchased a new home 1 year ago, our home came with Whirlpool Appliances. I was so excited because we were renter. The refrigerators after a year all of the LED lights have gone out, and the refrigerator make a very loud noise. I have called customers service several times. Their respond is, Sorry. It only has a 1 year warranty. The cost of the light would be over $500.00 dollar and that dont included labor. Dont even know the cost of fixing the loud noise. I just want people to be aware of Whirlpool appliances. After only 1 year of service it not going to work. Whirlpool will not fixed them. It sad we work hard to get a home and how will have to spend a fortune to get them fixed. Whirlpool you need to make better equipment. With is coming without home we were not giving an opportunity to buy an extended warranty.

We bought this washing machine from Lowes 5/15 and from the beginning have noticed that clothes especially dark fabrics come out of the washer with white fuzz or sediment on them. They need to be washed again and the fuzz isnt removed with a lint brush. I called whirlpool and they told me to use fabric softener. I dont like adding chemicals to my wash due to a skin condition. Lowes say they have never heard this complaint but clearly others have experienced this problem from the above reviews. Dont buy this washer. It doesnt clean your clothes. The only thing the customer representatives from Whirlpool wanted was to sell me an extended warranty. Why would I want that when the washer doesnt even clean clothes?

I purchased this machine in February 2019. The standard one-year warranty covered the first service call less than one year later. This call was related to the main control board. If this part goes out it will prevent the washer from advancing through the cycles. A technician was able correct this problem by resetting control board. That was sometime the first year. The next call was for the same problem and it cost me $90 to have a technician reset the board again. I then learned how to do it myself through online research. However, I had to do it more regularly and this got old as you can imagine. I did buy myself about two months of time by purchasing a used part but it soon failed as well. This main control board cost $564 if you get it from the manufacturer. This exceeds the cost of the machine. It was purchased in 2019. (The same machine has gone up to $740 today.) I had no other problems with that appliance however, it appears nowadays with electronics taking over cycles vs. mechanical parts you will not enjoy the same longevity as I did when I got 16 years out of a GE washer before this one. I have replaced this machine with a competitors product that costs less than the part except for the 5-year warranty from Lowes.

The oven is a joke. It does not self-clean. I have to buy oven cleaner and clean the oven like in the distant past. They are lying about it being self-cleaning. Do yourself a favor and buy a real self-cleaning oven. NEVER WHIRLPOOL.

We bought a new washer and dryer back in August. We have always bought Whirlpool. Whirlpool (or the government) now is trying to save the planet by regulating the water level in your washer. The water levels are so low your fabric softener & soap leave lines on dark clothes. IT SUCKS! It does not clean like our old washer. Very dissatisfied and would love to return it and get a washer where you can regulate your own water level. Its unbelievable that a manufacturer can make decisions for the consumer like this AND sell this feature which you PAY MORE FOR. TAKE IT BACK! Ill never recommend this product to anyone.

I purchased my Cabrio Whirlpool washer 4 years ago and have had problems every since I bought it! Thank goodness I bought the extended warranty! The last two repair bills were over $1000 each! My warranty just ran out and I had it repaired last two months ago! This is not my first complaint! When will they start listening to consumers? This is ridiculous! Now I am faced with the problem of just trashing this washer or spending another $1000 to repair it! Something needs to be done! I am warning all of my friends and family and will post again my problems with this washer on all my social networking sights! Whirlpool needs to take responsibility for their problems! I will never purchase any Whirlpool products ever again if they do not assume responsibility!

This refrigerator stopped working withing 2 weeks of delivery. Lost a great amount of food. It was a real hassle to get the warranty company out. Took several days. Now there are places on each shelf in the refrigerator where food freezes and I have to throw it out. I am not real happy with this.

I bought my Whirlpool gas stovetop in March of 2016. The burner knobs that connect to the stove is made of plastic and all 5 knobs broke within the first year. Each year I have replaced knobs and had issues with the knob breaking and then not being able to tell if the gas is off or on. I have called and talked to people at Whirlpool about this issue several times. Although they seemed concerned they will not replace the knobs and I have had to purchase them through Whirlpool. The gas stovetop obviously has a serious and extremely dangerous design flaw. I have kept some of the broken knobs just to tell others about this terrifying flaw. Again, last night the gas was on for several hours before we discovered it!! I called Whirlpool again and they were unconcerned. The Model is #WCG97US0DS00, Serial#D60509297. Beware and DO NOT PURCHASE this gas stovetop. I wish I had not bought mine.

My Whirlpool has been in use about three years. It was purchased on sale at a very reasonable price. My only complaint is the heat dry function which somewhat fulfills its purpose, but I usually have to hand dry some dishes. Overall, it is an average dishwasher that gets the job done. The best feature is that it is very quiet; you barely notice that it is running.

In the last two years, the inner glass door of the oven has exploded. The last time was Tuesday, 14th January. The oven door was ajar because we had just finished cooking dinner. The noise was deafening but the worst thing about it was the large pieces of glass thrown all over the kitchen. Most of which were large enough and sharp enough to kill a child and seriously wound an adult. I phoned Whirlpool to report this. The operative I spoke to was very polite but told me these things happen and I could have banged it a while ago and left a weak spot! She also said a Supervisor or similar person would telephone me that day. It is now Saturday 18th January and NO phone call. MY concern is there is no mention of this being a possible problem in their literature and their obvious lack of concern under a Health and Safety situation. Not to mention the cost of replacement door glass.

We purchased Model WTW81920758200YW0 on September 8, 2012. Its performance has been unsatisfactory, not cleaning the clothes as advertised. Not long after the warranty expired the main bearing failed, bringing a local service technician and we were left with a bill of over $300.00. Yesterday, the machine stopped in mid-cycle. The display went blank and the lid lock would not release. I called a local service company for a visit and the soonest a repairman could show up was next week.A call to a service we had used for the bearing surmised that without knowing the cause of the failure they could only guess that a circuit board was at fault. That visit would be over $300.00 with labor and materials. That was the last straw. We broke the lid lock to retrieve the contents and took a ride to buy another brand of washer. We went back to the appliance store where we purchased this machine to buy a Samsung front loader. The salesman apologized for selling the Cabrio in the first place. Good money after a bad product.

Our home came with an Asko dishwasher, theoretically a premium device though the experience was not the best. Anyways, had to replace it after a few years and decided to buy a Whirlpool under the assumption that if an Asko kind of sucks, being so expensive, it was not worth the money to spend big bucks on an expensive dishwasher. I could not have been more wrong! Bought a middle of the pack Whirlpool, I think we spend around $500. Complete junk. I had to use our Sears home warranty like 6 times. They replaced two times the computer board, all the sensors another couple of times, motor, you name it! Worst part is that all of the non essentials part that also broke off (wheels, and plastic pieces of the door) were not covered by Sears warranty so I had to end up using glue and all kind of contraptions to keep them together. Finally, when we decided to put our house in the market we replaced this junk with a Bosch. So far so good. Whirlpool actually never even washed properly, now with the Bosch we finally know what it means to have a dishwasher that really washes for real!

On April 17th mid morning I noticed that the freezer side was not keeping items Frozen. Everything was melting period. I then opened up the refrigerator side all the items are not as cool as they should be. I then proceeded to do a Google search to see what I should check for in regards to the freezer and the refrigerator side not keeping cool. I then proceeded to pull the refrigerator out to inspect the back of the refrigerator. When I did that I noticed there was a hot mark on my wall, as well as a huge it burn mark on my floor. I then unplug to the refrigerator do the huge fire hazard and I touched my floor and it was very hot to the touch.I called my stepfather who is a firefighter and had him come over right away. He said we needed to take the refrigerator outside right away because the compressor had overheated and that is why it started to burn my floor. He then went to the fire station and got a heat sensor check machine, and we checked my wall and floor and we had to make sure that it was cooling down so it did not start my floor boards on fire so then we had to put a fan on it to cool it down. I then went and purchased a new refrigerator, due to this one was no longer able to be used or repaired. The refrigerator was only four years and 5 months old. For a $1,300 refrigerator it should last longer than 4 years.I called Whirlpool the following day or two days later and regards to this issue. The only thing they could tell me is that they were sorry, this refrigerator almost started my home on fire and we have six children a family of 8. It ruined my floor and part of my wall in my kitchen and we have lost a few hundred dollars and groceries. This is ridiculous and not the first time, I read a few others having this issue, Whirlpool said they have never received any complaints in regards to the refrigerator burning the floor and does not see it as a fire hazard at all.

I’ve been struggling with this new washer since I bought it a year ago. It’s sold as a water saver machine, but it continually leaves white residue and lint on my dark clothes that will only come off if rewashed with no soap and no other clothes. The technician who came out ran a cleaner through the machine and that was it. It’s recommended that the cleaner be used once a month, but it doesn’t seem to do any good. Per the appliance dealer I’ve reduced the amount of detergent I use to a tablespoon. I still get the residue. Definitely not a water saver and a crummy washing machine. Don’t buy Whirlpool!

The trim on the front the my Whirlpool electric range has rubbed off. This is where the knobs for the burners are located. It was replaced once during the Whirlpool 1 year warranty (so it obviously happened with the first year!) and again during the second year we have had it. We have an extended warranty but have been told that it is not covered. It is ecstatically unacceptable. We have not used any type of harsh cleansers on it - simply a sponge to remove any spills yet it keeps on disappearing. I strongly recommend against buying any range from Whirlpool as it is quite obvious that they do not stand behind their products beyond the first year.

On October 29, 2009, we bought a new Whirlpool 30 gallon gas hot water heater to replace a Rheem we had for 20 years. We immediately had problems with the relief valve leaking, so we ran at the local hardware store and bought another valve. Next, we had trouble lighting it (husband was a plumber years ago) but a call to the hotline and we were in business. Now just over 3 years later, the pilot light started to cut off at will. Troubleshooting solved nothing. We called the hotline again and were given a part number, an authorization number and told to go back to Lowes for a replacement part. Figuring how our luck runs, I called first and was told there was no such part number. Trip saved. Now after reading all of these reviews, we have decided to cut our losses and buy another Rheem. You can find the Whirlpool hot water heater sitting beside our 2-year-old Kenmore HE washing machine (also made by Whirlpool) on the garbage pile. No more Whirlpool!

Weve had our Whirlpool Cabrio washer and dryer just over a year. I like them both but then we are having problems with our lid. The first one cracked after 9 months and they replaced the lid. Two months later, the new one cracked and they replaced the hinges and lid again. I assure you we are very careful when lowering and lifting the lid. I do 80% and my husband does 20%, and we are very cautious of it especially after the second one broke. Now, I was just putting laundry in and the third one cracked while lifting the lid. There is obviously a problem, and Im wondering if anyone else is having the same issues. Eventually, it will crack all the way through which will cause the glass to pop up and the lid wont lock. I will not buy anything with a glass lid again!

I found this site while looking for a part number for the thermocouple. Lowes had one, but not for the FG model. I decided to call the number on here from Chris to see where I could buy the correct one with left-handed threads. I was told that they would sell me the conversion kit, but I couldnt get just the $8 thermocouple. Then $47.90 later and the conversion kit is on its way. Im not happy about it but at least I got 6 years out of my water heater before the thermocouple failed. The plus side is next time, I can get the $8 part from Lowes and not be without hot water for a week.

I own a Whirlpool Cabrio washer, model #WTW7800XWO. The lid to the washer has completely detached for lack of a better word. It literally blew-off during the spin cycle and is hanging on by one hinge. My husband is disabled and I have had to go without using the washer for several days, waiting on a repair person not to mention the expense that will be incurred.This was a very potentially dangerous situation. My washer is barely older than one year. To add insult to injury, when I contacted the customer service department, I was told I would have to purchase and replace the lid or pay $299.00 for warranty insurance to have it covered because this is not considered a Quality Control issue.The service person has told me that both hinges and the lid will have to be ordered and replaced, leaving me without a washer for several more days. No one has been able to tell me why this happened. I fear this happening again after repair and do not feel safe with this washer. I would appreciate a response as soon as possible.

I purchased the Whirlpool Duet washing machine October 2010. When I first got the washing machine, it shook the house (new stick built house) when it was on the spin cycle. They had a repair man come out to tell me that there was nothing wrong with it, it was fine as it was. We thought it was ridiculous, but we are young and didnt know better. He also told us we should fill up the washing machine more than what we where because the clothes wash better when its packed. Big mistake on our behalf! The washing machine has ate thousands of dollars worth of clothing. We did what we where told, so we thought we were doing something wrong. Little did we know we were doing nothing wrong. It was the machine. Then a sock found its way to the drainage field which let water pour out of the washing machine throughout the laundry room and going to the rest of the house. What a mess. We called and they found the problem and removed the sock. Still didnt fix the damaged clothing issue. I called them 1 year and 7 days after we got it and Whirlpool still wont cover their product. They said they where sorry they couldnt help. Well couldnt and wont are two separate things. Its a shame they wont stand behind their product after I bought over $6,000 appliances from them. You think theyd be a little more compassionate to their customers after spending that much money? Now you know how they treat their customers. Dont buy Whirlpool. They (Whirlpool, Maytag, etc. ) are maybe cheaper than their competitors, but its probably worth the extra money if you know theyll stand behind their product. Very unhappy customer!

Whirlpool convection/microwave GMH6185XVS - In 2011, we purchased a whole new kitchen for our home with the top of the line Whirlpool products. The sorry side of this project was our microwave. This product has been terrible for us! It has been removed from our wall 4 times for failing... and four times we have gone for weeks at a time with a big hole in our kitchen wall!! All of the failures were due to the microwave not heating food or drink, and all, according to our local dealership, were for various different reasons. Again, it has failed and our local appliance center who we bought everything from does not want to deal with it anymore. I dont blame them... I dont either!! It looks beautiful up there above our range telling me the time of day... My wife and I are older adults and take very good care of everything we own. There certainly has never been any abuse to this product (not to mention we spend half our year at a winter home so this microwave only is used for 6 months a year). I contacted Whirlpool customer service about the reliability of this product and their response was that it is now not under warranty and we should deal with our local store about repairs. I have a small Sharp microwave sitting on the counter below this crappy excuse for one that stays there all the time in anticipation on the Whirlpool going down!!! The $60.00 Sharp never fails me!! This was our 2nd time around purchasing all Whirlpool products for our house. We did the same thing when we built back in 1990. All appliances performed as they should have back then. It seems Whirlpool integrity has gone downhill. I will never buy another Whirlpool product nor I will recommend to anyone I know to do the same. Good luck to anyone who purchased one of these.

I bought what I thought was a great washing machine. It is a top loading Cabrio from Whirlpool. The machine leaves white residue on all my dark clothing. It is a disaster. I am following washing instructions exactly, using HE detergent, loading the right amount, I even tried using PODS. I tried different temperature water, different cycles of washing and spinning and the same thing happens. I had an old Maytag that broke that cleaned beautifully. This thing is a piece of garbage and I would love to send it back if they would let me. DO NOT BUY IT. I AM BEGGING YOU, YOU WILL BE VERY UPSET.

Just wondered if anyone else has had a problem with the paint bubbling up and peeling off their washer and/or dryer. My washer and dryer are in my laundry room off the kitchen with a heat and air vent in the room and I dont understand why my paint is doing this. They are about 5 years old and have always been in this room, never in a garage or basement. My dryer was rusting on the outside about 3 years ago and even though I bought the extended warranty, Whirlpool said it was only cosmetic and they wouldnt do anything about it. I bought them at Lowes and they were good enough to give me a new one to replace it. Both of the machines now have the paint bubbling up and peeling off and there is nothing that can be done. Anybody else have this problem and if so what can be done to repair the paint? This is my 3rd set of Whirlpool washer and dryers over the past 44 years and I will purchase another brand next time.

On 11-29-2014 we were washing our laundry and our whirlpool washing machine started making a really loud noise so I went to investigate the problem. I open the bottom part of the washer to find out that the whole cement block to balance the drum was on the floor of the washer so I called the 1800 number on the machine and no one at whirlpool corporation wanted to even help. No one said sorry. No one said Let me see if I can help. No one. Every one I talked to they cant help at all. No one apologized once about the poor product that whirlpool sells and the defect that their products has. My washer is one year and one month old. So I can say truly with confidence that whirlpool product are the worst in the world plus their customer service even more. It is very sad after we paid all kind of money for our washer now I have to buy another one after one year and one month. Very bad customer service.

We get the error code F1 in the start of the cycle and when there is 21 minutes left, we have to stop and reset at least 7 times before the water fills. We put a new sensor in for over $200. The second problem is it goes off balance no matter what the load is. I was going to have it fixed (if possible). After reading all the above I wont waste any more money on it and go buy an old fashioned reliable washer. What a piece of money sucking machine especially when I dont have any extra money to waste down the drain. I wish I knew before. There are a lot of people this time of year I would have rather given the money for a needy cause. How disappointed we are with Whirlpool!

Was weary due to not a name associated with furnaces, but we installed a 100,000 Btu unit 2 stage and have not had any issues thus far.

I purchased A Whirlpool washer model WTW4816FWD some six months ago and it is worse than my 13 y/o washer I got rid of. When wringing clothes it seems be out of balance as it bangs like crazy even when clothes are adjusted. I thought it was the feet but no dice and the auto sensing levels allows for the washer to fill completely with only three items in it? The noise it makes while washing can be heard throughout the whole house too. The cycle takes three times as long of any Ive ever used! I hate this thing.

I am completely dissatisfied with the Whirlpool Cabrio top loading machine. Our washing machine is less than one-year-old. It doesnt get the clothes clean, especially the darks, and it is so rough on the clothes that they come out twisted tied into knots. The dark clothes come out dirtier than they went into machine. Even though we use the dark detergent on the dark clothes and program for an extra rinse cycle, the clothes come out with white powder all over them. They need to be washed again and sometimes again. And sometimes they still dont come out clean. That is not very energy efficient. The clothes come out of the machine so wrinkled that everything needs to be ironed. I can imagine making washing machine that doesnt do its primary function, which is to get clothes clean. Todays families do not have time for this extra work.

I have had my stove for 3 years and it works fine. However since I have become a grandparent, I have been extremely worried about the chance of being burnt. the problem is once you turn off the burner, it doesnt look any different than it does when not in use. It stays hot for a very long time however. Hot enough to burn or melt anything. There is no blocking a child from reaching up and touching it. I have placed a loaf of bread near it only to have it melt down the side. The burner didnt look hot at all. This was at least 15 min. after turning off the burner. Im not trying to cause issues but I believe this is a real danger, not only at the risk of someone getting a burn but also to the point of an entire family losing their home or even their lives. A simple flammable item being knocked over could start a fire. I ask that someone look into these risk.

I have owned the Whirlpool Cabrio for one year now. I cannot express enough what a complete waste of money this machine is. It literally does not wash clothes in even the most basic interpretation of washing. Clothes are almost in the same position as when they were put in the machine. Dont even bother with stain removal, it just rubs stains in and makes them worse. Seriously beware. Very expensive and not worth one dime. Im replacing with the Maytag. I should have stayed with in the first place. I will NEVER buy Whirlpool again. Must have skipped the entire product development on this one. I wouldnt even give it a one star review but the submission wouldnt process without it. WASTE OF $$ DO NOT BUY.

I purchased a new Whirlpool (2015) Model: WRF736SDAM13 French Door Refrigerator. Two days later, water was dripping from the light in the top of the refrigerator. I was removing about a cup of water twice a day, which dripped from the light. The company was friendly when I called, and offered a replacement or repair. I elected the repair as I felt that would be acceptable. The repair man inspected the refrigerator and determined the problem to be condensation from the water holding tank, located in the top of the refrigerator. He stated that because the incoming water has the opportunity to reach room temperature prior to entering the fridge, and because of the high temperatures (80’s & 90’s) the water holding tank has condensation that collects in the top of the refrigerator, which drips onto the top of inter refrigerator liner, and eventually drips through the light. He stated there is no fix, as it is not broken. While it is not broken, this is a bad design error, which would affect anyone who lives in an area where the temperatures exceed 80 degrees outside, which could only be fixed with a collection tray that would allow the water not to drip into the refrigerator. Currently there is none available. Because I only had the refrigerator for two days before the problem was reported, Lowes allowed me to make an immediate exchange. However, had this been purchased during cooler temperatures, the issue would not have been noticed until after the 30-day time frame and the exchange would not have been an option. When I made the exchange, I noticed that all the 3 & 4 door refrigerators are made the same and will have the same problem. I ended up exchanging it for a Samsung model. Kudos to Lowes. Whirlpool, you need to find a fix for this problem if you want to sell me another one.

We purchased Whirlpool Cabrio 8.8 cubic ft Electric Dryer with Steam Cycles (Chrome Shadow) Energy Star Model WED8500DC and Whirlpool Cabrio 5.3 cubic ft High-Efficiency Top-Load Washer with Steam Cycle Model WTW8500DC and have had no issues at all, only personal issues, such as me being 54 tall and cant reach the bottom of the washer tub to take out all my clothes, so my husband helps, he is 5 9 tall and can reach in it fine, so we do laundry together now! We have washed very small loads to large loads such as, bedding sets without any issues at all. We love the gorgeous look as well. We have only owned these since November 2015... so about 4 months now, but we are completely satisfied! We have always owned Whirlpool, our old set we bought in 1998 and they finally gave out in 2015! Whirlpool for life for us!

I bought a Whirlpool washing machine, model WTW4855HW, and was I ever shocked at how noisy it was. The wash cycle had a grinding noise that was just too much. After 2 loads I sent it back and didnt regret having to pay the restocking fee. I just couldnt believe that with all the technology we have today, that they couldnt build a quiet machine. Im an engineer so I know there are methods through gearing, belts, soundproofing, etc, to produce a quiet machine. Remember the dishwasher of days gone by. You couldnt watch TV with the dishwasher going. Nowadays, you can stand in the kitchen and have a nice conversation with it running. The technology exists. As a matter of a fact, my old Maytag that finally went bad after 10 years was fairly quiet. So, if you dont have your washing machine in the garage or basement room where you can close the door, dont buy this machine! Bruce in Portland

Five years ago I bought a brand spanking new HE set with a top load washer, top of the line Whirlpool. That washer has been a piece of junk and getting it serviced has been a nightmare. It broke, i.e., the computer part, and was out of commission for FOUR MONTHS. I live on an island off of Alaska, luckily I rented one for the duration but STILL. That was an EIGHT HUNDRED DOLLAR MACHINE. I liked that they are new and shiny and look cool. I hate that the electronics broke after a few years. Ive had washers dryers that lasted TWENTY YEARS. The next set I buy will have plain buttons for cycles and NO ELECTRONICS. None. And still none. Electronics instead of plain buttons. Im not kidding, I will never buy another one with electronics. I bought a top of the line Whirlpool HE top loading set for over $1400 five years ago and that washer has been a bust. I have had a repairman out over 5 times and the last time he took it out and kept it in the shop for FOUR MONTHS. I will never buy a fancy set again. I will buy the old kind with the plain old buttons. Do not make this mistake yourself! Just buy a plain old one!

I have purchased a Whirlpool Washing Machine Mode W/P WM ROY 6212SD(31089) Sl.No.INF 153400517) GRAY/CHR TN 6.5 on 05.12.2015 with two years warranty on complete washing machine. The warranty period over on 04.12.2017. Exactly after over 3 months the machine start giving noise and we had been in touch Whirlpool and registered the complaint during last week of March 2018 and their local service center people visited, charged Rs.500/- service charge and informed that the machine to be taken to their service center to ascertain the complaint. After over a week informed that the machine complaints of Tub Support, Seal, Bearing, Drive etc. and the estimate is Rs.5,900/- including transportation (hardly 6 kms). The machine cost was only Rs.16,900/- then. I am surprised to know that just after 3 months of expiration of warranty the machine went wrong and the cost or repair costs me Rs.5,900/- is very huge. I hope the concerned will examine this.

We purchased both the Cabrio Whirlpool washer and dryer approx. 3 years ago, while still under the manufacturers warranty the lid cracked upper right corner. It was replaced and we were told by the repairman at that time this is becoming a common problem that he himself has seen this exact failure to several of these washers. Whirlpool needs to fix the problem. Shortly after this happened we receive in the mail the information for the extended warranty. Due to having this already happen, I phoned the extended warranty department for Whirlpool and specifically asked if this same thing happens again will it be covered under the extended warranty. My answer Yes.Well it happened again, called extended warranty provided them with a detailed description of what happened, they would send someone to replace, the service gentleman arrived today, called Whirlpool and they denied the claim. So they LIED. I instill honesty in my children and am proud to say I hold honesty as a high value. We were told it was cosmetic, the glass is buckled and the lid has to be held down to engage the lock mechanism of the lid. COSMETIC, this is a SAFETY concern. Where have our American values gone... Whirlpool used to have them back in the day... Shame on you Whirlpool.

I recently purchased a top of the line self-cleaning Whirlpool/KitchenAid range. Or so I thought. I used the self-cleaning feature for the first time only to find out it literally does not do anything. Whirlpool quickly answered my Saturday morning phone call and were very professional. When I told them the Aqualift did not work, they asked if I purchased the Aqualift kit. No, what does it contain? Two sponges and a scraper. Basically I was told I would have to clean the oven manually. That would be fine except I have osteoarthritis and cannot clean it manually. Shame on Whirlpool and KitchenAid and Consumer Reports for not doing their due diligence and not testing important features accurately, over a greater period of time with real day-to-day scenarios with people who actually know what they are doing.

About 29 Nov 2011, I bought a Whirlpool microwave, which model no. is magic cook 206 (mech). Sr No. CNF103400315, when we bought this item, we asked for the start up kit, but at that time they said that in grill microwave we dont provide start up kit but after a month when I again raise for start up kit, that time they give but in start up kit some item is missing and the sealed is open. So I kindly request you to take some action to the shop.

Not cooling properly on wpf560smywc2 French door - Milk only last 3 days. Temp wont stay consistent. 4 times out and say normal. Ice is forming on fan in freezer and back wall causing no flow in refrigerator but freezer cooling. Only 3 months old. Lowes Service Advantage (Extended Warranty) nor Whirlpool will replace or do anything about it. Was told 3 times out and replacement then today they sent me email with their policy or 3 times out with a repair (Parts must be changed) wait 30 days then another repair etc. then on 4th repair will replace. Lied to buy sales and called liar by repair guy when he told Whirlpool nothing wrong. I just wanted a new one cause I didnt like features. Lowes has a return policy which has in fine print only 30 days for refrigerator so they wont help. Was told I have to do a food loss claim and they would email form. Still hasnt happen. Lied to and get a replacement or repair and cant afford another.

I bought this washer (model WTW7800XW) on 12/23/2010. Never happy with its performance from the beginning. Within the first 18 months, the lid hinge completely rusted and broke. The repairman stated that the hinges and glass lid would need to be replaced at a cost of over $400. We paid $899 for the washer. Instead of paying that much, not knowing if it would only last another 18 months, we removed both hinges and removed the lid manually to use the washer. After complaining to Whirlpool about the problem, they thanked me for the info so they could use it for the future. The latest problem to arise is the light inside the washer. The mount for the light was made of steel and has completely rusted away, so the light is just hanging inside the washer. Whirlpool needs to step up and resolve the issue with an extended warranty for these machines.

Watery body from all the refrigerator side since 9 – 10 months and complained to Whirlpool 2 months back. They changed the thermostat 2 times but no use. Problem same. Please help. I complained during the last warranty days. Please let me know.

Within a few months after I purchased my gas hotwater heater, I started having problems with it not wanting to stay lit. It was purchased in 2004. I see that this is an ongoing thing with Whirlpool. Every time I would call them, they would give me stupid answers on what it could be. One lady got hateful with me. I have replaced every part several times and Im having problems. About every two to three months, Im replacing thermal couple. As of right now, Ive been without hot water for eight days. I called and he told me about a trip button that is in the little white thing that has wires going to the thermal couple. I push in on it and then tried to start my heater and it worked. They have never offered to replace it or even give me a discount on a new one. No one should be having so much trouble out of your hotwater tank. This is not normal. These are defective and should be recalled. This company is ripping the consumers off and we need to stick together on this and do something about it. Im afraid to buy another heater because I can see that the new ones are still junk. What do you do?

Worst refrigerator Ive ever bought. Previous one still perfect shape. 22 years old. Freezes everything on top shelf. Motor making grrrr noises. Had repaired. Now bottom crisper drawers so cheap the plastic is breaking. Drawers wont slide. Now Deli tray lid snapped in half! STAY AWAY from this USA made product.

We purchased a Whirlpool Refrigerator Model Number WRS555SIHZ06 Serial Number HRA2506806 on July 15th 2021 from Lowes. First one from Lowes came off the truck damaged so working out of a cooler in the kitchen for 2 more weeks. Now 4 months later the compressor is out and all the food spoiled like $400 bucks gone and food is expensive these days. I called and Whirlpool said no food allowance and no replacement. Fridge can be brought over - so repairman will come out in 6 days and then say he has to order parts then I wait two more weeks then the repair. So 3 weeks without a fridge with the holidays coming up and people to feed and food to cook. This is going to be interesting. I hate Whirlpool Refrigerator - never again will I purchase one of this appliances. The GE I had for 12 years and no problem at all for 12 years. What is going on with these companies????

Whirlpool Refrigerator WRS526SIAH00. Well we have always had a lot of trust in Whirlpool appliances over the years. Just about everything we have is Whirlpool brand including water heater. We remodeled our kitchen and bought a new refrigerator in July 2013 (just for the color/look change). We have had nothing but problems from day one with the water/ice dispenser water may or may not work. Now (AUG 2015) the refrigerator side started freezing our food, milk and tea gallon jugs frozen solid. Went down a self fix list on an appliance parts website using our fridge symptoms, said it was probably the bimetal defrost thermostat. Replaced that part. It didnt fix it.So I did my own troubleshooting and found the cold air was continuing to push from freezer into fridge area, found this cheaply made plastic damper broke and stuck open. Now that part will cost another $50+. Whirlpool knows about these cheaply made parts they have put in these appliances. You cant even get to this part without taking things apart. This is a cheap manufacturers plastic part and Whirlpool knows it. Its not the consumers fault. It was a joke when we received an extended warranty offer from Whirlpool for just $208 per year or $626 for 5 years - I wouldnt spend another dime with Whirlpool. The price is high because they know how many parts are breaking on these units. You shouldnt have any repairs for 10 years on a refrigerator. We are stuck with a lot of Whirlpool products now, but we are done with this brand. Dont waste your money.

It took several delivery attempts to get a refrigerator without cosmetic flaw and it only lasted four years before Freon leak in evaporative system occurred. It would have cost more to repair than replace. Needless to say, I replaced it with another brand.

Product: Whirlpool Gold Series, Model WRX988SIBM01: Purchased 2014 at Lowes. 2nd day after delivery, called Whirlpool, refrigerator not working properly, freezer drawer will not close, condensation on outside. Sent person that delivered the refrigerator to fix problem, freezer had frozen ice behind each drawer approximately 2 inches that would not allow drawers to close. Delivery person used hair dryer to melt ice and adjusted drawers. Still periodically have to physically remove ice build up to allow drawers in freezer to seal properly. Ice maker stopped working, makes no ice at all, ice comes from inside refrigerator not from freezer, bad design.Today woke up to freezer drawers completely thawed and had to throw away all food, panel shows temperature at -2*. All food thawed and unable to be cooked/used. Called Whirlpool could not send someone until next Tuesday (4 days). We are a family of 5 and cannot wait that long. Unfortunately have called 3 other appliance companies only to find that refrigerator has to be repaired by special technicians! This is our first Whirlpool, bought because made in America, have been very disappointed with our $2500.00 purchase. Not sure that we will ever purchase another Whirlpool product, our inclination will be to buy less expensive product and choose to replace as opposed to paying recurring service calls + parts and labor.

This dishwasher was a mere 2.2 years old, installed by Lowes-hired technician and the part will cost $168 through Whirlpool, plus labor on both first visit and installation visit. I would not advise to purchase this or similar product from Whirlpool. What really makes me upset is that I learned from customer service that this unit was made in the USA.

The machine was great and handled large amounts of laundry. It was very expensive but my wife was happy with its performance. A year and a half into owning it, the electrical code F70 comes up and it stopped working. When I checked online, I found it is a common problem. I contacted whirlpool customer service and they could not do anything. Spoke to the manager, Kiesha and she refused to help me even though I bought both the washer and dryer for a lot of money. Customer service is not a priority evidently. She denies that there is an on-going problem when both the internet and my service tech say differently.

I bought 2 Cabrio washing machines for my two homes along with the matching dryers. They worked for about 3 months, then the washers displayed OL Error during any wash cycle. I tried to contact manufacturer and have not been able to get service without charge. After reading the many posts I am not sure if I should dump both or start investing $$$ in service calls.

Whirpool WFW9550WW-00 Front Load Washer - Washer was purchased 08/09/12. No problems until 07/12/15 when washer stopped working mid-cycle. Motor control board needs to be replaced, actuator needs to be replaced. $500+ Our local appliance store suggested we call the Whirlpool customer relations number and ask for the parts to be sent free of charge. We would pay labor. They gave us the model number, serial number, the diagnostic info. Long story short, customer service told me she didnt know why I was told to contact them. They can not predict the life of a machine. Less than 3 years for this machine. 22 years for my old Kenmore. Our old Kenmore never had a problem, but we thought that we should replace it in 2012 in case something happened with old machine. WISH WE KEPT THE 22 YEAR OLD KENMORE.

Our 2005 whirlpool duet washer steel drum and plastic tub broke. My husband diagnosed the problem and opted to fix it to save money. The parts are under warranty but you still pay labor and technician visit running up to $250-$300. The plastic tub was obtained only if we paid for it $100 and the steel drum they sent under warranty. The plastic tub has a hole with a black plug and sensor in it. There is a discrepancy in the measurement of the old tub and new tubs hole that is slightly larger, therefore when installed a steady stream of water leaks out. I now have 3 plastic tubs as that was their solution, to send more of the same that did not measure correctly. An investigation was done to determine they were the correct parts. As asked we had a whirlpool technician come to verify parts were correct and being installed correctly and the parts sent would not fix the machine due to the hole discrepancy. Many calls were made to whirlpool and they continue to give me the runaround. They now are not taking their technicians information. The technician has given the information to 3 sales reps in the new england area and made several phone calls to whirlpool and no one is willing to give us a solution.

Purchased a new Jenn-Air JCD2295KES in 2007 when we remodeled our Kitchen. Its been a decent fridge. When it quit a couple of weeks ago, I had the repairman come. He informed me that the HV circuit board was bad and sorry but they dont make them anymore. What, a 7yr. old fridge and thats it? I sort of expect things to have to be repaired or maintained but to have to throw it away because Whirlpool chose not to carry the parts any longer. I decided to scour the net and see if I could find this legendary board. Lot of places seemed to have carried it but could no longer get it from Whirlpool. I found a place that could supposedly repair them but after a few days, they called and said the microprocessor was not repairable.I contacted Whirlpool and they gave me a place that does obsolete parts and although helpful, I thought they were real opportunists and wanted to charge me considerably more for a reconditioned board that a new one would have cost if I could find one. I kept looking on the internet to no avail and when I called Whirlpool again I was getting pretty upset. Here I am with a 7-year old refrigerator and cant get parts for it, thats just not right. They were pleasant but basically their stand was sorry, theres nothing we can do. I told them that I bought a lot of appliances as I have quite a few rental properties. I cant throw an appliance away just because I cant get a part. It just doesnt make sense. I feel Whirlpool/Jenn-Air simply doesnt care. Im not interested in their excuses, I just want parts. I dont think it is unreasonable to expect to be able to obtain parts for at least a dozen years or maybe even a little more.I posed the question to them. Would you buy a $2000 refrigerator if you knew it would only run 7 years? The customer rep. said no she wouldnt. Well, Whirlpool, neither will I. I was unimpressed with their lackluster response and offer of a $300 rebate on a new fridge. I can find better deals than that on my own. I have purchased many appliance and always actually liked the Whirlpool line but Ill not buy any of them again. Shame on you Whirlpool for letting your customers down. Just because you can ignore me, doesnt mean you should. Im in business and I would go to the ends of the earth for a customer to make them happy. No wonder the Asian companies are kicking butt on the so-called American manufacturers. If your not going to get service you might as well go for the cheap price.On a final note, I did after two weeks of searching find a board hidden in a little appliance repair shop in Colorado. It should arrive here tomorrow and was priced $150 less than the reconditioned board that the gougers Whirlpool recommended. I believe it is the last board on the planet. Hopefully it will get my fridge another 7 years down the road and by then Whirlpool and its subsidiaries will have been sucked up by foreign companies and under a different label.

I also have a side-by-side Whirlpool Gold Fridge purchased from Lowes Retail Store, and I paid $1,480.00 for it. It is now 4 years old and I just noticed large cracks on right, inside part of the fridge. I called Whirlpool and got a runaround. Some lame guy said, Sorry, nothing we can do for you.When are people going to stand up for their rights and fight for their bucks? They havent heard the last of me but I will put this on the back of my truck with a nice sign on it for thousands to see. If anyone else has had this problem email me at ** and lets talk. I will never buy any Whirlpool items ever, ever again! Buyers beware! I also hold Lowes Retail Store responsible for this. They should research and stand behind what they sell, they are no better than Whirlpool!

I purchased a side-by-side Whirlpool refrigerator less than three years ago, but about a year ago we discovered it was leaking from the freezer thats located on the bottom. Initially we thought that if we simply defrosted the sheet of ice that formed on the bottom of the freezer - it would stop the leaking. Its hard to keep up with - I checked into it on the Internet and discovered that there is a clogged drain hole that is causing the leaking.Apparently, a number of people are experiencing the same thing. I called Whirlpool (since our local repairman suggested we contact them because this is a chronic problem and is likely to happen again). The customer service person kept pushing me to buy the extended warranty with their repair that will cost nearly $400!!! Without it - it will cost nearly $200 that doesnt include any parts. Its a new refrigerator, very bad quality and theres damage to our kitchen floor, and then Whirlpool wants me to pay $400 to repair the mess they made! VERY UPSET...

I have the same lid closure issue expressed by many consumers and whirlpool refuses to acknowledge this as an issue, only recommends purchasing a new lid at $225. Lid design is flawed, metal L bracket connects to plastic housing/trim/side of lid, causing glass to pop out and stress cracks between screws. New models of same washer have redesigned lid, no cross reference part number or dimensions listed to determine if new lid will fit.

This is the worst washing machine we have ever owned. We purchased the Whirlpool Cabrio washer and dryer set at Lowe’s in Loganville, GA on 04/11/2010. Today is 02/22/2013 and the transmission is shot in the washer. It began making an extremely loud and terrible noise during the rinse and spin cycle. We called a local and trusted appliance repairman, and after his diagnosis including estimate to repair the washer, it totaled over $525.00. This is a terrible washer. I will never ever buy a Whirlpool appliance again. Oh, forgot to mention we have purchased four (4) major appliances from Lowes over the past 2 1/2 years in addition to purchases for our plumbing business and wont do it again! Also, Whirlpool couldn’t care less and there is just one complaint after another for the exact same problem online.

We purchased a gas range (Whirlpool AccuBake model # mfgxfg361lvt1 serial ry1810956) a few years ago and have been very unhappy with the gray grids that it came with. We wrote to you about how we should clean them and you recommended heavy-duty degreaser, pin31552a and gas grate & grill cleaner, pin3167a, which we purchased. Neither worked, even with heavy elbow grease. We are very upset. We have purchased Whirlpool products all of our life and would like an answer or some type of explanation. If possible, can we get the grids in black? We try our best to keep these things clean and this is a very bad patten.

We bought this Whirlpool Cabrio washer 2 years ago and have hated it since the first load. It does not clean clothes, and the so-called large capacity will barely clean 5 regular towels. And if you wash diapers, do not buy this washer. If a load is really dirty, you have to wash it 2 or 3 times for clothes to be clean. Then, there is the awful mildewy, moldy smell after a few washes. How can a washer that gets so bacteria-laden be allowed to be sold on the market. Ive been washing laundry for 45 years, and Ive never had this kind of wash-related problems. This washer is an overpriced nightmare. I cannot wait until I can save enough to replace it. And I am watching and hoping a class action suit comes out to force Whirlpool to take these washers back, refund the money spent, and apologize to all the people who purchased one.

Bought in October 2014. Died December 2015. The previous Whirlpool microwave this unit replaced was 10 years old and carried a 5 year warranty on the magnetron. Imagine my dismay to find out this unit carried only a 1 year warranty on the magnetron. So 2 months past warranty expiration Im left with a dead unit. I performed elementary troubleshooting. The unit has a fuse on the 120 Volt input. But the unit must be disassembled to gain access to the fuse. So what SHOULD be a five minute job turned into an hour and a half. The fuse wasnt the problem - replacement fuses blew like popcorn. Fuse placement within the unit without regard for service considerations is a poor design.To their credit, Whirlpool agreed to cover the cost of repairs if I would pay for labor. I agreed. A tech came out and looked at the unit. He said that he would have to order a bunch of parts and that he would be back in contact by the end of the week. Three weeks went by. There was no call from the tech; my messages on his voicemail generated no response. So a couple of days later I purchased a replacement from a competing manufacturer.

Whirlpool Cabrio - We bought this washer in June 2013. The gearbox just went out (17 Nov 2015). Terrible product. We had to buy a new washer; and it wasnt a Whirlpool.

I feel Whirlpool has a terrific portable dishwasher. I really like the way it is set up and it is a very nice looking unit. They could improve on their customer service towards their customers. My dishwasher got a crack in it at the top of the door where you open it and they would not send anyone out to fix it for me. I paid a pretty penny for this dishwasher and felt they should have fixed it for me. This happened in the 1 year warranty period. Otherwise I am very happy with it. I had previously had another one that lasted me 14 years.

I purchased the Whirlpool Cabrio HE top loading washer and front-loading dryer about 7 years ago. It has been okay, but nothing special. Recently it began stopping in the middle of the cycle and showing an F51 error. Then all of a sudden the noise during spin was deafening. Brought out a tech, who came and did some eval. Left with some basic maintenance. Did a load, and happily no more F51 code, but still so very loud during spin cycle.Called again; tech returned and said that drum and shaft would likely need to be replaced to the tune of some $500. The same story as others have told. We should have bought the extended warranty. Like others, I also felt that washers lasted at least 10 years. And that seemed a short time given expectations in the past of 20 years of service. Im disappointed in Whirlpool. Even though Consumer Reports gives the Whirlpool Duet washer (new 2013) one of its highest reviews, I cant bring myself to buy another Whirlpool product. It appears to me that this warrants recall as well.

I bought a Whirlpool duet washer and dryer. These appliances are still under one-year warrantee. My washing machine was broken for four weeks, and they have been unable to receive all of the parts needed to repair it. They have made three appointments to fix the machine, telling me that they have the parts and only to cancel the appointment the night before. I have tried to get Pacific Sales to exchange the broken machine, but they will not do that or compensate in any way. This is a top of the line model; I would have been better off with a low-priced model, and I might actually have a machine that worked. Whirlpool supposedly had the parts on back order, which is not what Whirlpool informed me when I was able to reach them.

Pulled a track home water heater out to replace with a Whirlpool 12 year smart heater. Well within 4 years with tank flush every year the water coming out of my hot water tap looks like mud. We have whole house water filters and when you drain the sink there is a layer of rust. I called and asked them what I should do and they told me to flush it with apple vinegar. Did this but a week later it was back. Called again and was told to do it three times with apple vinegar. There was nothing about this in the care manual about apple vinegar. I will never buy Whirlpool again NEVER!

Dishwasher has had multiple issues in the 4 years of use. - Incomplete cycles - need to call repairman to figure out why the dishwasher does not complete cycles, fills with water but doesnt go into clean cycle - In 2 years had to replace grommet due to leaking water. - Top rack slide rail plastic ends broke needing to purchase both new ones. - Detergent door quit opening - door does not open during entire cleaning cycle.- Design flaw with silverware rack on the door, be careful not to block or silverware will not get cleaned.

Handle needs smarter design. I purchased model #WRT311FZDM00 in November of 2015, didnt install in my new home till December. I am a single senior female, so there is little wear on the fridge, unlike a family of several people and with kids. The door handle actually broke just behind the screws that hold it in place, the plastic part of it broke into a couple of pieces. The cost to replace this handle is approximately $80, which is ridiculous in my opinion. Please start making things of quality materials instead of cheap plastic, especially at a stress point of a part. Even I know better than that. All 4 of my major kitchen appliances are Whirlpool, as well as my washer/dryer. I thought I was buying quality products. Hopefully things will hold up better with the other ones.

We purchased 2 Whirlpool Cabrio washing machines in 2011. Both required service calls in June 2015. After 3.5 years, the repair company diagnosed that the Whirlpool Cabrio model number WTW7800XW2 bearing needed to be replaced for an estimated $650.00 and recommended that we purchase a new machine. The other machine was spewing water out of the side of the machine. The repair person took the machine apart and could not duplicate the problem.

I bought a whirlpool washer from Whirlpool on February 27, 2011. Since then, they have come out and repaired the washer for 5 times. They have even taken the whole motor out, and replaced it. The last time they came, they said I would have to pay for the next time. Now, it has broken again, and I have to pay for a washer repair that is less than a year old. We bought the Whirlpool washer at Sears, and neither Sears, nor Whirlpool will stick by their product. We cannot afford another new washer, and to pay for repairs is a stretch too. Is there anything you can do?

The American Standard 95% 2 stage variable furnace is by far my favorite furnace to install. I know exactly what to expect from this furnace and I have had zero factory issues with this model. Outside of making a few sheet metal transitions this American Standard standard 95% furnace was very easy to install as well. And like the 2 stage variable … no factory issues.

The front of our Whirlpool washing machine started to rust in one place at the bottom within six years. Now it has broken out in three of four places on the front. We are very dissatisfied with machine and will never buy one again.