Four years old and only used by a 2 family home. No kids overloading it. Probably wash 3 loads a week on average. After 4 years, it has started the grease flying out of the bottom and now leaking water. My appliance repair man told me to scrap it and buy a new one. The repair and the parts are too expensive and in the end it is still junk. I realize things wont last 30 years like they used to but can I get 7 years out of a major appliance?

I purchase a Cabrio WTW7800XW0 3/28/11. After the year warranty I started to notice sand like substance in the drum of the washer, which lead me to look around the drum. I noticed that the light was completely rusted and flaking, the area around the light was rusted as well. I call customer service at which time they said it was not warrantied, but they sent me out a new light. This did not repair the problem! The rust has continued causing the area around the lid joint to break. Also the area around the bleach dispenser is showing rust- the same side as the light and the lid break. They have said this is not covered and only agreed to pay 1/2 of cost of materials (no service).

Broken drip pan was cracked, replaced, and wood floor damaged, also replaced. Compressor replaced. Ice warmer replaced. Hinge on crisper door broken, replaced. Freezer door handle keeps falling off. All this in first year. Builder purchased 1 year Extended Warranty. Freezer ices up occasionally. Repairman advised using a hair dryer to free up the rails. All this on a $2,000.00 Whirlpool Refrigerator. Do yourself a favor and dont purchase this Refrigerator. Model #G16FDRXXY.

Purchased my Whirlpool dishwasher in 2005 model number GU2500XTPQ3. So it worked for about 10 years and I am fairly happy with that but I have a warning, my control panel shorted out putting out thick black smoke and I was unable to turn off the dishwasher. I had to turn off the switch at the breaker box. If my wife had of been the only one home she would not have known how to turn it off and would have had to call the fire department. I dont know if the short would have led to an actual fire but with that much heat I have to believe it would have. Warning, dont run the dishwasher when no one is home. Hope this helps someone.

Cabrio Top Washer - Disappointed!! Its selling point was using less water but do they realize that you DO have to use a little water to clean clothes. Leaves residue on every load and where I have to use the extra rinse cycle and that still doesnt work. This product is going on eBay today! Never again Whirlpool.

I purchased a 40 gallon water heater at Lowes and installed about 3 years ago. A couple of weeks ago, it got an upper sensor failure code on the gas valve. It would heat by resetting (turning valve off, waiting a minute and then lighting) but after a few minutes, it would fail again. I called the customer service and they mailed out a new upper sensor. When it came a few days later (I paid for shipping), I installed it but the same failure code. Again, the only heat I could get was by resetting the valve several times before a shower. I called customer service again, told them what I did and they said, Oh, the problem is the gas valve then. So they mailed out a new gas valve unit. It then came a few days later and I installed it according to the enclosed directions to the letter. Still got the failure code and still had to keep resetting it to get any warm water before a shower.I called customer service again, told them what I did and he said, Well, did you flush the water heater with apple cider vinegar before you installed the new gas valve? I said, No, it wasnt in the enclosed directions to do so. He said, You should have done that and it would have worked. I will send out a new gas valve. At this point, I blew up. Two weeks with no reliable hot water. I told him I want a new water heater and he refused. I asked to speak to his superior. He said no. Dont ever get a Whirlpool product. Some other crappy company builds these turds.

This washer is a piece of junk!! It doesnt use enough water to clean the clothes and now it wont spin them dry. I have maybe two loads a week on a regular basis. I have always used HE detergent. Never overload. It is only three years old and I have been having to go to the laundromat because I cant afford a service call and especially if it is what they say which costs almost much as the washer. Be ahead to buy a used washer or a cheap one. It wasnt getting the clothes spun out dry enough - dripping wet. Then it flashed od and ul and sd and f51 and then it kidnapped my clothes - couldnt get the door to unlock with the pause or power until I unplugged and still had to wait several minutes. They refuse to help. Do not buy this machine!!! The customer service was not one bit of help. Instead she wanted to charge me $350.00+ dollars for some plan.

The Whirlpool refrigerator I ordered from Home Depot came to my house dented. I then had to get Maytag/Whirpool to send me the same model refrigerator which they then subsequently forgot to include the ice maker with the refrigerator. It has been nothing short of an act of Congress to get in touch with someone from their Customer Service department for them to send the ice maker that they forgot to include. Ive had to call them at least 15 times to get them to resend the missing ice maker. Absolute nightmare. 10/10 will avoid buying Whirlpool in the future.

I have been using Whirlpool brand of appliances for over 40 years. They have always served me well and very dependable. Im a semi retired HVAC contractor and also installed Whirlpool heating and air conditioning systems in peoples home, also very satisfied with the results.

Same as others, We purchased a Whirlpool Cabrio Washer and there is a bearing problem (which seems to be the common issue reported). The washer is unusable at less than 5 years of age. The repairman told us its a bearing problem and its common for this to happen to the Cabrio. How can an Whirlpool get away with selling a defective product?

11 months after I bought the fridge it started acting up. I paid 1900 for this thing. The temp kept getting warmer and the ice maker quit working. I had to pay for a service plan. Ill never buy a piece of junk Whirlpool product in my life again and ill broadcast their poor quality to everybody in my 5000 congregation. I work to save up to buy this product and its junk. Ill end donating it. Im very upset at this junk product produced by Whirlpool.

My Whirlpool refrigerator is about 13 months old and the paint is peeling off. I was told my an associate at whirlpool that I could have a service person come replace it for approximately $500. And this is only for one door not both.

The washing machine started leaking and making a noise like a freight train 6 months after purchasing it. We complained in February 2011, but the parts were not available until March 31, 2011. The same problem occurred in September 2011, and we are still waiting for the parts until October 18, 2011. In the mean time, I have been spending hundreds of dollars doing wash at the laundromat.

We have a 2008 Whirlpool gas range that has worked reasonably well but lately more and more of the electronic push switches on the keypad have stopped functioning. So now I cant set an oven temperature as only a few of the 10 number switches still work. I talked to an appliance repair guy who said that the typical electronic keypads are notorious for burning out after 3-5 years because of heat transfer from the oven. So now Im stuck with an oven that is virtually unusable and a $400-500 cost to replace the keypad control. Is it worth replacing? Can the faulty control buttons be somehow fixed? Shouldnt Whirlpool acknowledge the faulty design and provide a free (and hopefully better) keypad? There must be thousands of people out there with similar circumstances. What about a class action suit? Any advice/opinions out there?

Extremely unsatisfied with their customer care. I purchased a washer and dryer 18 months ago and did not choose to purchase an extended warranty. I currently need a main control board replaced after the machine stopped spinning and draining. I hired a wonderful handyman, who originally suspected the lid--locking mechanism was the problem. When that was replaced and the machine still wasnt functioning, he determined the main control board needed replacing. This is a manufacturer defect and costs approximately $300 for the part, not including labor. Of course, my machine is no longer covered under the extremely limited manufacturers warranty that only lasts for 12 months, so I am stuck picking up the bill. Once done with all the parts and labor, its cheaper to buy a new washing machine especially because they still wont add a warranty to it after its fixed. I think its absurd that a manufacturers defect isnt continually covered under warranty no matter how old the machine is. Customer service continued to tell me I should have wasted more money on a company that doesnt care about customer satisfaction and purchased an extended warranty originally. Horrible investment! Will never purchase Whirlpool appliances ever again!

We purchased 3 Whirlpool Gold appliances, fridge, range and over-the-range microwave in 4/2011. Since that time, the fridge needed repair, the microwave door had to be replaced and the range had to be repaired. Now the heating element on the microwave went and Whirlpool will not fix the problem. We purchased the extended warranty through Whirlpool and they are saying it is not worth fixing. We paid $470.00 plus tax and install and now all they are giving us is $348.00. Since we have had repeated problems with these appliances, why not just fix the problem or replace the microwave??? What Whirlpool customer service told me was that would be options for us if we did not purchase their extended warranty. Tell me, is that fair? The cost to repair the microwave was $388.00 and they are giving us $348.00 - do you not think for the $40.00 difference, it would be worth to spend it to keep us happy. We will never purchase another Whirlpool product again and will tell everyone we know not to buy their products.

Purchased Cabrio set last year. Worst set I have ever owned! Clothes do not come clean. Takes forever to wash. Must wash multiple times to get clothes clean, even on deep water settings. Does not spin water out of sheets and blankets. Dryer dries unevenly. Waiting on repairman because dryer will not come on.

Purchased a Whirlpool Cabrio washer WTW5800BW0 September 2014. Two years and 8 months later it no longer works. Call Sears and Whirlpool and was basically told I should have purchased a warranty. Whirlpool tried to sell me an extended warranty for $495.00 which is about 80% of the original sale price of the washer. Was told it is my responsibility to care for the maintenance of my purchase. WOW. Way to stand by your product. So now its my fault they sell a product that does not last longer than 3 years. So we tried option 2 - called a repairman. His response save your money and buy a new washer. WOW. A repairman rather lose money than try and fix this washer. Save your money and pass on Whirlpool products.

I bought my Whirlpool Cabrio Top Loading HE washing machine and dryer duo in February 2009. I carried an additional extra extended warranty for an extra 3 years. Now, at the dispenser where you add the bleach, it has rusted. The rust has gotten so bad the lid has detached from the body of the machine. I cant understand how a machine less than 4 years old could rust so badly. I called Whirlpool to complain and they suggested I get it repaired and my cost. A car that sits outside in rain, sun, snow and hail does not rust in 3 years. I bought the machines from Home Depot. The way Whirlpool has handled this, I will never buy another Whirlpool.

I bought at Lowes. The first one was sent back (doors stuck, suction cracked lining). Now the temps are not working in the fridge or freezer. All the food got dumped. Its sad. My old one lasted closer to 25 yrs. (and may I add up to ten children). This one has only been used by adults. I thought I could trust Whirlpool?! I sent info to local Lowes. We will see if theres any help.

We brought this in Jun 2015, within 1 weeks it developed its problems. Ive had service men out 10 times for ice buildup on the freezer side, and the refrigerator side not cold even on max setting, and the problem hasnt been solved yet.

Our Whirlpool Cabrio washer is 2 years old and also sounds as if its a jet on the runway preparing for takeoff. The spin cycle started this about a month ago. It is so loud now. It is just SCARY. I am so angry! No recall??? seriously???!!! Rip-off. I will NEVER buy anything Whirlpool again!!!

Cabrio top loading washer - I have had this set for 3 years. The first 8 months it was fine, then came all the rust. I had to go to the BBB and file a complaint as everyone at Whirlpool would not help. Last year they finally replaced the top, and now, its rust yet again. I rinse and dry the machine when I am done using it. The repair man said it was because manufacturers are not using primer and just one coat of cheap paint. What now? Ill see if I can get the lid off and sand it and use rust preventer on it. Never again, I should just junk this piece of crap and Whirlpool should shut down if they cant make anything worth our hard earned money.

Whirlpool washing machine #WTW58ESVW1 - I bought this thinking Whirlpool was a good brand name. I was totally wrong. My machine is two years old and the auto sensor switch has quit working 6 times. One time it only did 6 loads of laundry. Another it only worked for 6 weeks. That time I replaced the switch myself to save money on a repairman. Ironically the switch is still under warranty but they will not replace it unless a serviceman comes to confirm that the switch is dead again. This is because 2 have already been returned to them. Obviously, there is a problem with the switch. The company will do nothing. They used the excuse that I did not purchase an extended warranty. This is merely an excuse. Do not purchase any Whirlpool products. You will be wasting your money and time having to end up going to go out to do laundry.

We purchased the Cabrio washer and dryer set 2 years ago (7/22/15) from Lowes and have HATED them since day one. The first wash in the washing machine left clothes dirtier than when they went in. Our clothes have never gotten truly clean. The washer has a HUGE tub which is what I liked about it so I can wash my King sized comforters. What a joke that turned out to be. The comforters only get half wet even on the deep water setting. The machine even left dark stains on my light colored comforter and ruined it. Fast forward to 2 years later and the washing machine stops spinning and fills with water clear up to the top of the tub and wont drain. I had to put the machine on the rinse and spin option to get it to drain. Tried a different setting and it worked for a few months but started doing the same thing. The washer seems to be unbalanced no matter what size load I do. I am thoroughly disgusted with this machine and wish I would have never purchased from Whirlpool. The dryer has always worked fine until recently (2 years after purchase). It quit drying the clothes and leaves everything twisted up and wrinkled, even if I take them out of the washer and shake them out before I put them in the dryer. Doesnt matter what setting I put it on, the result is the same. So now it seems as though BOTH of my machines only lasted 2 years. Im not going to bother fixing them, these will be used as target practice. I will never buy another Whirlpool product again.

I purchased a Fridge/Freezer just over 4 years ago. It was an expensive one. The gas is gone and they cannot re-gas it. If I was told this when I was purchasing it I certainly would not have spent this money. I rang the concessional team. They would give me nothing towards a replacement as they had not one in stock, POOR Service for a big company. I am in business and this is not the way I would treat my customers. This has certainly turned me away from purchasing Whirlpool Products, despite having a industrial washing machine and Dryer. For the record, I had 2 servicemen to check it and they were most pleasant. It was beyond repair.

Every washer Ive ever had has just a spin. Why dont these new washers? If the washer is un-level why would you add more water? They need a spin cycle to drain the water out of it. No more rinse and spin just a spin. Very aggravated.

We bought a new refrigerator 14 months ago and the compressor went out New Year’s Eve. Of course, expecting 30 people to celebrate! The first refrigerator Lowe’s delivered was loud and we called and asked to have it replaced, which they did. The second one was also loud and we debated if we should send it back also but we just put up with it! Second mistake was not buying the extended warranty. Since we have always had good luck with WP we didnt purchase the extended warranty. Neither WP or Lowe’s would do anything to help. The repairman who looked at it and diagnosed what was wrong said the compressor was undersized for the size of refrigerator and that it had worn itself out trying to keep up. He said he would not put in the same size compressor or it would do the same thing. Hence the loud noise of this model. I will never shop at Lowe’s again, and after 30 years as a Whirlpool customer, I will never buy another product from them. Also, if you plan to buy WP, buy extended warranty. They also leak water.

The only thing cheaply made is the push latch on the dryer. Both are pricey for what you get, I thought, though they were the cheapest Lowes offered. We have had the pair for a little over a year. So far no real problems, though we really do not like the latch door. You have to slam the door to get it to close. To do it over we would probably have shopped a little longer and for the same money got a better deal.

I am very unhappy with this Whirlpool refrigerator model# GX5FHDXVQ 04. I bought this model in October 2011. You have to push the left door to close it and if you dont then the fridge will stay open. I had a Whirlpool tech come to fix this door problem so this is what he told me: 1) You have to push the door in order to close it properly; 2) Before closing the left door, I should first open the right door (losing energy); 3) The gasket will break very fast; 4) Buy a three-year protection plan because you will have to use it; 5) The freezer is very uncomfortable. In the bottom drawer, you have to fit your stuff. If you put your freezer stuff in a drop higher, then you cant close the drawer, so I am losing space; 6) Sometimes when I fill up the fridge, I move the temperature to #5. After a day, the top shelf back stuff will freeze and the front stuff will stay on fridge temperature. Yesterday, 4-18-2012, for the second time, the freezer gets a sheet of ice. Repairman will repair it but who knows. This fridge looks to me like a lemon. The height is 70 but listed as. I rate this fridge with a CCC.

Ours is a glass top & has 2 dual burners & we are very pleased with that feature. The oven however takes quite long to preheat & the alert sounds are so weak you can barely hear them. It was a rapid purchase on a sale item. I wish we had shopped a bit more.

Got this refrigerator when I old one of 10 years through AHS home warranty. I asked for a similar one to the one we had. Surprisingly we received the Whirlpool which turns out to 5 times better than are old GE. Same height and width but deeper and with more compartments. We are extremely happy with it

I had a 6 year warranty on the new Water heater and about only 4 years into it the tank began leaking. Whirlpool replaced it but of course I was responsible for Parts and labor to replace it. The replacement only lasted just over only 2 years and just outside the total of 6 years from original purchase date on the first. Whirlpool refused to discuss it since it was a few months out of warranty. If someone else has purchased this heater it would have failed at 2 years and they would have had to warranty it anyway. I will never own another Whirlpool appliance because of their substandard products and warranty. I only wish I had reviewed the reviews of others and taken their experiences into consideration and not purchased Whirlpool. I am now out for another heater and reinstallation charges again.

The Whirlpool range #GY398LXPQ00 is four years old. This is the fourth major problem. Oven overheats and will not function. I set it at 350 and the bottom coil and broiler both came on and overheat quickly. This is the third time with same problem. I am going to have enough invested in repairs to buy another range. I shall never purchase another item made by Whirlpool or any of its affiliates. That leaves me with Samsung or Bosch, I think. The people are very curt and offered no help at all so calling them is extremely useless. This range is definitely a lemon. Too bad, there arent avenues to make them replace it. I am angry, disappointed, and disgusted. Are you listening, Whirlpool? Never again. May your company go down the drain.

We were a Whirlpool family, and have been using a Whirlpool front loader – Duet Steam Model # WFW9500TW - for the past nine years without any issues until recently when it started to vibrate. Technician sent by Whirlpool blamed it on failing bearing and that it was cheaper to replace than to repair (In hindsight, I wish we had tried repairing). Naturally, we decided to replace with a new front loader from Whirlpool - Model # WFW6620HW. Our previous version had a max spin speed of 1000 RPM and a capacity of 3.5 cu. ft. This new one has a top spin speed of 1160 RPM and a capacity of 4.5 cu. ft. The main problem with our old one was vibration, and this was being caused by the washer going into high spin while the clothes were not evenly distributed throughout the drum. In one spin, the clothes would spin perfectly without any vibration, but in another spin of the same cycle, the washer would not allocate that same clothes properly throughout the drum, which leads the drum to cause vibration from unbalanced high spin. Vibration is a problem, because like most Americans, we live in a wood frame house, and have a basement underneath with the washer located on the main floor. Vibration from unbalanced high RPM spin gets sent down to other areas of the house, causing damage, drywall cracks, separation in trims, etc. And these are all only the damages one can see with their eyes.One point about vibration and some myth busting. Provided that all your washer legs are meeting the floor and not on a saggy floor, your washer should not vibrate more than it does during an empty spin. If it does, then it is due to faulty, poor design/engineering. What happens is when the steel drum becomes unbalanced with laundry in high spin, it starts to shake as more of the weight is on one side, which one can notice looking inside the washer window. There are concrete weights fastened to the top and bottom of drum to keep the drum in place and to reduce its shaking tendencies. However, this weight also causes the washer cabinet to wobble if the drum itself is shaking. This wobble in turn causes the washer legs, which may be firmly grasping the floor, to very slightly come off the floor, which one can feel if touching both the washer feet and floor with their finger at the high spin of an unbalanced spin. And that motion of legs coming off the floor and hitting back at high RPM is what causes vibration to be felt on the floor and to be seen on the cabinet. Of course, this effect is amplified with washers that decide to go into an unbalanced spin with an even higher max spin. When our old washer perfectly balanced the clothes, it behaved like it was running high spin while the drum was empty. This is how all washers should behave, especially in America where the vast majority of homes are wood frame based. However, that was not what we experienced with this new Whirlpool. If a washer is not capable of balancing out the clothes, extra function or feature should be deployed in containing the drum shake to within the drum, and not allow it to escape.First, our old front load Duet Steam Whirlpool was Made in Germany. This new one is ‘assembled’ in America. The door window of the new one is plastic and feels cheap and flimsy, but I expect all the darker color door windows of newer front loaders to be plastic. Consider it cost cutting. We did not look for additional anti-vibration technology because our old Duet didn’t have anti-vibration features aside from its two springs and four suspensions. We decided not to use Load & Go because I have personally seen liquid HE detergents gum up over time, so I didn’t want to risk it gumming up inside the washer.After the installers left, I spend an hour cleaning the outside of the washer to perfection. Sadly, time wasted. Once I was done, I first did a wash without clothes, and then with clothes in Normal, fast spin cycle with drum about 2/3rds full. Just pants and t-shirts. There is a recirculating pump at the top of the drum to distribute the water, and to also distribute soap mixed water. But I am not sure if this is without problems. These pumps can collect soap residue with time, and you will eventually end up rinsing the laundry with soap mixed water even in rinse cycle.In getting to the first spin in wash cycle, I was flabbergasted to see how, just how rudimentary, I want to reiterate the word rudimentary, the load detection was before entering high spin. Our nine-year-old washer had a more comprehensive one. The new washer would spin the clothes at very, very low spin and simply see if the drum is most evenly spinning. That’s all. Compared it to our old washer which would also shake the drum to see if there was movement from side to side, because clothes can change their position when entering high spin. This rudimentary load detection causes the new washer to create an even worse uneven load distribution around the drum before spin, even though it may seem even at very low RPM. So, why is the new washer’s load detection so basic? I believe it is due to ball bearings.Front load washer models from other companies employ ball bearings to reduce vibrations from uneven loads. Whirlpool does not employ such feature, at least, they do not advertise them. However, to my surprise, I hear metal balls hitting each other every time the drum direction changes during the wash cycle. I inquired Whirlpool about this and I received contradictory responses. My theory is that the basic load detection before spin speed is used because Whirlpool assumes any changes to load distribution will be taken care of or reduced by the ball bearings of the washer. But this ultimately allows the washer to go into more uneven spins. The bearings may also be used to increase the tolerance of what is considered an ‘unbalanced load’ in order to get the washer to go into spin cycle faster, decreasing the time involved of the washer to go into spin cycle. Sadly, to my dismay, the new washer ended up causing a worse vibration than our old one with failing bearing.I called up the retailer the same day of delivery and complained of vibration. He first sent an installer to see if it was installed properly, and upon showing the installer of the vibration issues, the retailer sent me a new washer couple of days later thinking the first one was a lemon, and even though it has less noisy draining noise, it too exhibited the same issues with it going into significantly uneven spin. In the end, we decided to return the Whirlpool washer all together, at a loss of $200 because the retailer did not hold up to their spoken return policy.We have done many loads in this washer to see if our loading is an issue, loads of varying sizes, loads of varying types, loads of weights, and we maybe only had an evenly distributed load around the drum about once or twice. Once it was a King comforter. But, like our old washer, this too ended up not distributing properly around the drum in the final spin cycle and started vibrating, even though it was vibration-free in the previous high spin cycle. This proves that the problem exists directly within the washer, not the floor, leveling, load, etc.Some other problems with the washer: - The washer door, Load & Go dispenser at bottom, and single load dispenser at top are all plastic parts which all vibrate significantly during fast spin cycle. Especially the Load & Go dispenser which keeps hitting the cabinet to make banging noise. - Drain sounds are much, much louder than our previous Duet. It was even louder in the first one we received. Combine this to uneven spins and this washer can perhaps compete with an engine in terms of the sound it generates. - Single use dispenser at top left will hit the washer door if washer door is opened when the dispenser is also in open position. - Buttons are sometimes unresponsive, to which I have to power off and try again. But this has only happened a couple of times.- There is a small ¼ in. opening where the steel drum meets the rubber gasket, opening in which items like coins, etc., may fall through and are irretrievable. Don’t think small socks would be affected.To potential buyers, I suggest you proceed with caution when it comes to this washer. Understand the retailer’s appliance return policy and make sure it is shown in paper. It can save you a lot of headache. Get the extended warranty of three years because manufacturers only give you one-year warranty for a reason. I would also suggest that you avoid this washer at all costs if you have any floor level below where this washer is to be installed, especially if the level below is a basement. Your house is more important and more valuable than a $1000 washer.In the end, I am very disappointed in Whirlpool, an American company. Perhaps Whirlpool focuses their attention on top loaders, not front loaders. But Whirlpool had nine years to improve their washers, and it is sad that we may now have to go outside of America for a quality product to be used in American homes. P.S. No solicitation please, Whirlpool. This washer is in the process of being returned. P.S.S. I already posted this review in Whirlpools website, and it is under moderation.

I had a perfectly good Kenmore range, but I didnt like the color. I purchased a Whirlpool 30-inch gas range at Lowes. I had problems immediately! The repairmen were at my house 6 times within the first year. My warranty expired and they wanted me to pay for an extended warranty. I refused to pay any more for this piece of junk! I fought with Whirlpool and demanded they either replace the range or reimburse me the full cost. They finally agreed, after many heated conversations, to replace or reimburse me as long as I promised not to purchase a Whirlpool product again. What kind of company would say that? A company that knows their product is defective and has poor customer service. I opted to take the new range that they promised wouldnt have the same problems. It is having the same issues as the original one. It shuts off in the middle of cooking and it is infuriating to say the least. I can promise Whirlpool I will never purchase a product from them ever again!

Favorite feature is the double oven. Both ovens are separate self cleaning. Top oven smaller, perfect for a pizza, cookies, small stuff. Great features for entertains, multiple foods can bake at same time. Ceramic top easy to clean, boil overs cannot seep under anything. I have had this oven for over 10 yrs, minimal repairs.

Bought this microwave combo oven from Lowes. Went to change the charcoal filters, as specified by the owners manual, and the top cover and the side cover fell apart when I removed the filter cover screws. After two appointments the service tech came out for about 5 minutes to tell me that only mechanical failure is covered by the extended warranty which I also purchased from Lowes.The problem with Whirlpool is that they make the top cover, and some other parts, with cheap thin plastic which crumbles when exposed to heat. The repair tech said, Dont worry. Ill see what I can do. And then he left. Actually the warranty booklet said wear and tear is covered in addition to mechanical failure. Its inexplicable to me why any manufacturer would use cheap plastic for an over the range product. And I intend to fight this until I get this appliance repaired under warranty.

Purchased a NEW Whirlpool side by side refrigerator (WRS965CIA) and it was delivered on 2-3-14 with a dent in the door. The retail store ordered a replacement door and this order was approved by Whirlpool. 4 months later, I still dont have the door. My 8 calls to the retail store say that Whirlpools Trade partner is not returning their calls or emails to get this resolved. My contact with Whirlpool was met with contact your Trade Partner. Vicious cycle and still no replacement door.

We purchased 4.0 cu. ft. Cabrio Top Load Washer with 6th Sense Technology MODEL WTW7340XW2 on 11/20/2011. We are a small family of 3 so use of the machine is light. We noticed a strange sound and some leaks a week ago and called in a technician recommended on the Whirlpool website. To our horror he informed us that we need to replace the tub bearing assembly, rotor and stator - to a cost of $1095! This machine is not even 3 years old. Did we buy a lemon? I called Whirlpool. They were simply not interested. The online chat person sent me to the Whirlpool Customer Experience Team where I was told that I should buy an insurance plan to cover the costs of repairs. They then sent me on to the insurance department who want me to pay $338 to buy a repair plan to have the machine fixed. And then referred me to the Manufacturing division when I wanted to know how to escalate the problem - and if you call that number - there is no option to deal with problems - seriously?!? Is this what I should expect when buying the Whirlpool brand?

As very happy owners of a previous model of this fridge freezer when ours needed replacing, we went direct to Whirlpool and bought the latest model. What a mistake! Other comments on this site are so accurate if only we had seen them before. A kitchen floor covered in ice mush (cubes seem out of the question) and tepid water from the water dispenser whereas on the previous model it was chilled. Basic functions that the previous model excelled at. Sadly it is also badly designed inside the fridge. We raised these issues with Whirlpool within our first year who merely said sorry you are unhappy and thanks for your comments. Be very wary of Whirlpool products and service.

Whirlpool microwave model # gh4184xsb1 handle is falling apart. I have replaced the hood vent twice and the entire door once and now, its the same problem again. The plastic becomes brittle over a year to two years of use and falls apart. Whirlpool will only stand by their one year warranty, and is not concerned about a problem that many of its customers are having. I have read many complaints on the web about this same problem. My wife and I have decided never to purchase Whirlpool products again.

Reading the many reviews of malfunctioning washers and other appliances, I wonder why organizations like Consumer Affairs and Consumer Reports do NOT help the many cheated customers form a class action lawsuit or boycott or some other means to effectively organize and force manufacturers to return the full cost of purchase, taxes, shipping, moving and repairs for 5 years for every product. The manufacturer have NO consequences for selling shoddy, malfunctioning but terribly expensive products. We are all being taken for fools by the corporations.I was stupidly brand loyal and bought a Whirlpool Duet front-load washer and dryer because we had to leave our perfectly good 28-yr-old Whirlpool washer when we sold our house. The first set of instruction is to pull the electric cord from a small hole in the back of the washer. No amount of pulling would budge the cord. Finally yanked with all my strength, heard a snapping sound and 12 of cord came out. Then no more pulling, yanking or tugging would produce another inch of cord. So I took off the top of the machine and found the cord tightly wedged in the fork of a plastic thing that looked like part of a stabilizer for the drum.A similar plastic thing on the other side was broken at the fork, the snapping sound I heard. Freed the cord with lots of effort, but it was still firmly stuck way down inside. Removed the back of the machine, found the cord stuck inside a circular thing with one tiny opening. Took lots of time and effort to free the cord from that, but it was still stuck. Finally managed to reach the plug, which was firmly anchored to the bottom of the frame with an orange lanyard. Cut the lanyard with a knife to finally free the cord. This had to be an act of sabotage by an assembly worker, as no way could the cord accidentally jam itself into 3 different places too small for the cord to slip in, and it certainly didnt tie itself to the bottom of the frame with a lanyard.The hour it took to free the cord was just the start of troubles with this machine. It did start and kind of tumbled clothes in an odd fashion, but when it went into spin cycle, it literally jumped all around the room, almost jumping out the door. The whole house shook and I feared the floor would collapse. That machine must weigh well over 100 lbs. even without water and clothes. Next load I tried delicate cycle which had a slow spin cycle.Same result, even worse. I had to wedge my body in the 10 space between washer and dryer and press down with all my 170 lbs. to keep the machine from doing serious damage to the dryer, walls and floor. I contacted seller, Lowes, and they said call Whirlpool. So I did, but no response. Before buying that machine, I read many horrible reviews of Whirlpool Duet machines, but I have only owned 2 washers since 1967, both Whirlpools, so I had strong but stupid brand loyalty.

I like my dishwasher very much. Because we have hard well water I use Lemi Shine to cut down on any deposits. The top shelf is adjustable so that helps with large pans getting clean.

It has plenty of room. The compartments within the refrigerator are well organized. There is plenty of room in the freezer. Have had this for about eight years and going strong.

We just remodeled our kitchen and bought a Whirlpool kitchen suite in May of 2016. The refrigerator is absolutely terrible. I have had a repairman come out and fix the same repair/problem 5 times, a sheet of ice forms beneath the vegetable drawer (We have only owned the refrigerator for 5 months). Each time the repair person has come out it costs me a day of work due to having to wait all day for the repair service that Whirlpool hires out, well be there between 9am and 4pm. This morning I decided to check to see if the sheet of ice is forming again, it is. So I call Whirlpool again.Again, I call Whirlpool and ask if I can just get a new unit; 5 repairs in 5 months on a brand new refrigerator. The reply I get from Whirlpool is always well send someone out to fix it. The unit has to be deemed irreparable or a part has to be replaced multiple times. No parts are being replaced... no one knows how to fix it. I dont understand why a large company like Whirlpool would want people to write bad reviews for their products and customer service. Im extremely irritated with how I have been treated. I just want a refrigerator that works!! DO NOT BUY A WHIRLPOOL REFRIGERATOR!!

We purchased our first front-loader washing machine (Whirlpool Duet WFW9250WW00) just over two years ago. Since we purchased it, it has torn clothes and we have replaced the drum baffles twice (this would be the third time, but we are throwing the washer out), the drum seals twice (another place clothes can get caught). I had adjusted my washing (maybe I overfilled the washer, maybe I was using the wrong spinning speed), but every so often clothing would come out with holes or torn. The drum baffles must come loose before they come out, and clothing can get caught underneath them (I think that is where the tears occur). It has happened at least once a month and I had spent a fair amount of time trying to figure out where the clothes got caught and torn. Many people complain about bad smells from the washers (which I never had - I like the Tide with Febreeze detergent and every so often clean it with bleach or Affresh), but never torn clothing. I would really like to use a front-loading washing machine, but we are going back to the top loader - we cannot afford the clothing tears. I have seen that many people replace baffles (not many speak of clothing tears) and maybe in the future this problem will be addressed. But in the meantime, I would stay away from Whirlpool front-end washers. (GE makes some nice top loaders - and in 40 years of washing clothes and only owning two other washers, I have always thought washers to be an appliance that would last 15 years or longer with very little maintenance or trouble). I believe that I really tried to make this washing machine work out, but it got to the point where my husband did not want to wash baseball uniforms and other irreplaceable clothing in our washer.

I have had no issues with this brand of microwave. I have had built in microwaves before with this same brand and they have performed well. We use the microwave every day for some reason to heat up food or make hot drinks. I feel Whirlpool is a good product and value.

I was searching online and stumbled across this site. Funny that there were so many complaints about the console on the ovens, considering that my issue was with the console on a dryer I purchased. I have only had the dryer a year, and it stopped working. There is nothing else wrong with it, no codes, no problems with the lights, or anything else. A technician came out and found that it was a small plastic and metal button piece that helps the press here: spot on the dryer panel to connect to the start button on the console. The little arm had broken and the switch no longer worked.Figured we would have to purchase a new button. NOPE, apparently we were told that we had to purchase a new console (over $200 dollars, close to $300 with shipping)???!!! We were also told that wear and tear can cause the issue. Wear and tear?? On a dryer thats maybe run once a week for about a year? Try again, I think I need my boots because it sounds like horse** to me. I think I will pass this information along to people I know that are technicians so that they can let people know not to purchase from this company because they obviously arent going to address the situation. I think I might also utilize social media to let people know so that they dont have to go through this much aggravation. I certainly dont know what we are going to do, since it took me a year to pay that dryer off, I cant afford another dryer at this time. So unfortunately with a new baby on the way, you wont get any sympathy from me if your company takes a character hit.

I have Whirlpool 25 in. Side by side. I love the space freezer size is bigger than the old one I had. Makes ice as it should. Overall solid appliance that I trust. I purchased this refrigerator a year ago after research.

This washing machine is terrible. It barely cleans my clothes and frequently gets off balance. I am now on my second repair call in less than 3 years. (I bought the unit in the summer of 2013. It is now the winter of 2016.) The last repair guy tried to blame me, suggesting that I was filling it too much and with heavy materials. Last night, I washed 5 or 6 doggie towels. Not even large, bath sized towels. And the whole thing just stopped. It wont spin and wont unlock. What a piece of crap.

Cabrio washer - I have always had a Whirlpool appliances and have always been satisfied with them, but this is the worst washer ever manufactured. I bought it to wash heavy loads of jeans and it takes me all day to wash 1 load because it is always out of balance. No matter what setting I put it on I have to keep rearranging the load. Without putting up with that, the load takes 87 minutes on bulky wash. That is far too long and then you add all the time I spend rearranging it to get it to work. I think there should be a recall or at least admit you have a poor design. My son works for Whirlpool, but Im not sure I will be supporting this company again.

I bought a pair of Whirlpool front loading washing machine and dryer on May 23, 2011. The Duet Steam washer model is WFW9640XW, dryer is WED9470WW. Their high retail price was $1125 each. I did not pay this for them. I thought I got a great buy at Lowes for the price I paid, plus their 4-year extended warranty. Whirlpool used to be a very high-end appliance manufacturing company. Now, all they put out the back door is junk. I would advise not to buy Whirlpool front end anything. My washing machine started making noise about 2 weeks before I reported it to both Lowes and Whirlpool. The noise sounded like bearing not being lubricated, which that is what it ended up being.The noise got so loud that even with all my very expensive electronics (my home entertainment ctr equipment) I could not hear the TV which goes through an expensive Yamaha AV Receiver and those expensive Infinity speakers 7 channel system. The main bearing for the wash drum assembly was bad. After two emails and several phone calls to both Lowes and Whirlpool, Whirlpool was going to send the so-called re-engineered drum assembly. The style I have is 3 parts; the new one according to Whirlpool is one part, but if they put the same bearing in, youre going to end up with the same problem in another year. I live in a condo of just over 920 sq. ft. so really there is no room to repair them in my home, but that is what they are going to do. I will be getting the new drum assembly delivered to my condo and have the repair company doing this dirty job in the middle of my living room.Living in a condo, I have a small utility closet next to the kitchen where the furnace, hot water tank, and washer and dryer are. The closet needs to have some areas cut out with and installed two small hinged doors on each side, so if anything ever needs to be repaired or replaced, there would be a little bit more room to move items in or out. The problem getting the washer out is getting the dryer moved so you can disconnect the electrical plug, cold water hose for the steam, plus the vent hose. First, you have to get to the water valves which are very hard to reach. Because of the way cluster housing is made, they squeeze things into very small holes like the faucets and drain hose are located. I was asked by the repair person if I could help him lift these items out of the closet. I have had 7 fusion back operations and #7 left me in constant pain that I take a narcotic drug for pain daily. So, I called Whirlpool back and said the repair people were only going to send a tech. I was told that it is a two-man job: one tech and one helper. So Lowes needs to authorize two people since Whirlpool is sending the new drum assembly for free. I wish I could have gotten a new washing machine with the so-called re-engineered drum assembly. I am still probably going to have to squeeze between the bulkhead (wall) and the washer and dryer to disconnect everything since I am a small person. If I wasnt retired, I would have bought a different brand front loading washer and dryer, probably Bosch and took the loss on these piles of Junk. I love my country and do my very best even as hard as it is in this day and age to buy US. I served my country in the US Navy during the Vietnam War, just to see the civilians willfully buy Asian everything. So now, we have 4 Asian nations that own this country. I dont know why Whirlpool changed from a company that you could trust their products to a company that doesnt give a damn what they put out the back door. These companies still havent gotten the clue why folks buy goods from other countries. I think they need to open their eyes, but I guess with Whirlpool still being a company that is selling a very large number of appliances and making money off of us, suckers, they dont need to change. The only way they are going to change is if folks stop buying their junk.

My dishwasher is really a simple basic dishwasher. It is efficient and does a good job of cleaning. You can put many items in the top and bottom and the utensil basket can be moved for better cleaning or more room. If I had one complaint that would be that it is a bit too loud but other than that it is wonderful.

I purchased a home that came with Whirlpool appliances. I begged the company for GE or Maytag. Of course they went with the cheapest they could find. I must admit the microwave gets very hot but the dishwasher is a piece of crap! The water doesnt get hot and the dryer doesnt work. They tried to tell me it NEEDED Jet-Dry. I own 4 homes and have lived in all of them. Ive NEVER used Jet-Dry and all the others work perfectly. Run as far as you can from Whirlpool!

My glass stove top broke for the second time. The first time Whirlpool accused me of dropping something on it and chipping it. I didnt but paid the $400 glass replacement. Today while cooking, I put cold from the fridge not freezer, sausage into a warming fry pan. I heard the same pop I heard 2 years previously...sure enough the glass stove top broke. After a phone call to whirlpool, and hearing they were sorry but theres nothing they can do, I will write as many letters I can so others dont buy whirlpool.

I bought a Cabrio 2 yrs. ago and I wish I had my old washer back. I read reviews and checked out a lot of literature and thought I was getting a quality machine. What a waste of hard earned money. I cant get clothes clean, its loud, and it leaves soap residue even after an extra rinse. Whirlpool products arent what they claim to be. I had a freezer I bought because I bought a half a steer and it quit running and I lost all my beef - $700.00 worth. From now on I will stay away from any Whirlpool products!!

Washer does not clean clothes period. Darks come out covered with white soap residue and smell dirty regardless of how little soap is used or with using extra rinse, which takes 84 minutes by the way. Whites only seem slightly cleaner since hot water is used and you cant see the soap residue. If you wash more than 5 or 5 items at a time some do not even get completely wet. Just waiting for it to break down next according to the other reviews. I spent a lot of money to get a nice washer and dryer and ended up with junk. Id rather have an old 1970 washer, probably designed better and most likely would clean better.

I will never buy another Whirlpool again or recommend them to anyone, and discourage anyone from buying one. I bought a Cabrio washing machine just over 2 years ago and yesterday I received an F51 error code. The manual says that this code requires a technician to come a check for repairs. Well, before I do anything I google the problem, and lo and behold there are thousands of complaints about this issue with the Cabrio models. Some saying that what needed to be replaced were a control board ($280) and a rotor (unknown amount), not including the price of labor. Some said that Whirlpool knows about this problem and they covered the parts and repair. This didnt get my hopes up, but I called customer service and of course they said that there were no reported issues with the model and that what I found on the internet was probably an older model. Of course! The lady on the phone told me that they would not cover the costs and it would be anywhere from $300 to $500 depending on the route I wanted to take. That is a 1/3 to 1/2 the price I paid for the machine. This is ridiculous! I am tempted to just get rid of the washer and go with a better company that actually cares about their customers. This error code was definitely something they know is a big deal if there was nothing I could do about it other than call a technician. I paid almost $1000 for a machine that has barely lasted 2 years before I have to pay money to have it fixed. Not a company I would ever purchase anything from again!

I have owned a Whirlpool Cabrio model no. WTW7800XW2 washing machine for less than 3 years. The plastic frame for the top glass lid cracked (on the right next to the spring loaded hinge). After reading that other people have had a similar problem, I contacted Whirlpool about this and talked to its TN call center representative. I requested that Whirlpool repair the appliance free of charge since there is a known defect with it. She said Whirlpool would only offer me a 50% price reduction from the retail cost of the lid plus charge me shipping and taxes. I will not be buying another Whirlpool product as a result.

Aqualift self clean oven??? I followed the directions on how to clean my oven. I wiped and scraped out spilled residue from the oven. Then started the cleaning process. The sides of the oven were not cleaned even when I wiped them with a damp cloth. Scrubbing and scraping with the tools that came with the oven helped somewhat. The bottom of the oven was not cleaned. I had to continually scrub and scrape to get it looking half clean and even then, there were still spots that would not clean away. I would have preferred an oven that uses oven cleaner, it gets the oven much cleaner and with less scrubbing on my part. All in all I am very dissatisfied with the oven and would never recommend it.

On March 3, I purchased a dishwasher (Model: KUDE70FXSS1 Serial No.: F10202361) on Whirlpools VIP link, which will more likely be my last Whirlpool purchase based on the slightly damaged product and incredibly poor customer service Ive received. Upon delivery of the dishwasher on March 9, I noticed that the left rear wheel was damaged and slightly bent. I also noticed that the unit was a little off balance. But the delivery person explained to me that everything was okay and that the front legs just needed to be adjusted. I believed him and signed the delivery receipts with the additional note about the left rear wheel being damaged. At the time of delivery, the driver also happened to mention that J.B. Hunt did offer installation services for dishwashers. I then called Whirlpool customer service, which pretty much gave me the cold shoulder, and said that it wasnt in their policy. I had to request the installation service at the time of purchase and Whirlpool would not send someone back out. This made me upset because I initially wanted to have the dishwasher installed but your VIP link didnt show an option for installation. Im not sure how Im supposed to request the installation services when theyre not being offered. But the genius customer service representative thought that I should intuitively call Whirlpool when the link isnt on the website. This is the first demonstration of Whirlpools poor customer service, in my opinion. After a couple of days of driving around to get a hose and a cord to perform the installation, I finally installed the dishwasher on March 12. Once installed, I noticed that the hinge on the left side was rubbing against the tub of the dishwasher. The door hinge was bent and the main tub was slightly damaged. Again, I contacted Whirlpools customer service department who sent out a repairman who confirmed that the dishwasher needed new tub and hinges which were covered under warranty. Unfortunately, he told me that I would not receive a new dishwasher since I installed it myself. He would order a new tub and hinges and transfer all the equipment and wiring from my original dishwasher to the new tub. Essentially, I would have a refurbished dishwasher at a new price, which I do not want.I initially wanted to have the dishwasher installed but your VIP link didnt show an option for installation. If Whirlpools website worked the way it should have and offered an installation service, I wouldnt be in this situation. I would have paid for the installation and the people installing the new dishwasher would have realized that it was damaged prior to them leaving and ordering a new dishwasher. I am a customer and not a dishwasher repairman. No normal person would have been able to catch the damage that is on my machine. Second, I find it hard to believe that Whirlpools policy states to have all the equipment from my original dishwasher installed on a new tub. So, I paid $989 for a new dishwasher thats really a refurbished dishwasher because of the damage. I wish I would have visited this site prior to purchasing. I will never deal with Whirlpool again.

I bought a brand new Whirlpool washer and dryer. The Whirlpool Cabrio washer does not clean my clothes no matter what size load you have. I have tried every combination possible to get my clothes clean and 95% of the time there are clothes that don’t even get wet let alone clean! I have only owned this washer since July 22, 2018 and am now willing to give it away - that’s how upset and displeased I am with it! If you read reviews, stay away from this model - not good!

I hate hate hate this Whirlpool Washer WTW5000DW1! To put it nicely. This is my first washer without traditional agitator and the sensing feature. I will never again buy a High Efficiency Washer with these features. It constantly gets stuck on sensing! We rearrange the load over and over and it still does not want to work. I have researched the online videos and this is a common problem. I wish I had researched prior to buying this type of machine.

When we bought our side by side fridge (model GD5RVAXVB02), the manual said to clean the condenser coils if you have excess dust and/or pet hair. We have both. We tried with the vacuum and with a brush but it is impossible to get to the coils because they run side to side instead of front to back. You can only get to the first coil in front. The rest cant be accessed from the front, sides or back. I called to find out how Whirlpool recommended they be cleaned and they could only recommend a vacuum attachment tool (8171579A) to clean the floor below the coils or a coil brush (4210463RW) that cant reach the coils! This design is meant to fail prematurely. They could have easily installed the coils running front to back so they could all be easily cleaned.

We bought a Whirlpool washer (Model # WTW4900BWO) and dryer (#WED4850BW) and within 2 months I was having problems with the washer AND dryer. Every time I washed a load of clothes, the clothes would have some yucky stuff hanging all over it. I called Whirlpool and was told to try setting the washer on 1 Rinse with Softener even though I never use a liquid softener. Their suggestion did solve the problem, but why doesnt a brand-new washer work the way its supposed to? A short time later, my dryer buzzer stopped working and the knob would not advance when set on the Energy Preferred setting. I called Whirlpool again and was told they did not have a service technician in the area where I lived and that it was not likely that one technician would come on the same day to service both machines. I asked why they would sell their products in an area where they were not willing to service them and they said that is the choice of the store that sold it to me. Then they told me there was a service technician available about 40 miles away and they would fax the order to them so they could contact me. The technician who came did look at both machines and was able to determine that the control panel needed replacing on the dryer, but was not able to do anything about the Rinse Option problem on the washer. He suggested that I continue to follow the recommendation of Whirlpool as long as it works. I can do that, but Im not happy that a new machine does not work the way its supposed to. He also recommended NOT using liquid laundry detergent or fabric softener in my washer because it contains animal fat and can build up and cause problems. Nowhere in the manual did it say that. He took the washer apart and showed me how it was already building up under the washer basket. I told the technician that my laundry has had an unpleasant odor to it when it comes out of the washer and even after it is dry. He said that might be because of the small amount of water that is used in the energy saving washer. If these problems cannot be resolved, I consider this washer to be a lemon and hope it will be replaced with a new one. If I had to do it all over again, I would buy a traditional washer. I liked the idea of conserving water, but not if my familys clothes stinks.

I have a microwave (Model: MH1150XMQ-0) in my summer home. The microwave gets little usage but the door has cracks in all the corners. I have two other friends with the same problem. This appears to be a design flaw and should be corrected. The microwave is still useable but I do not know how safe it is.

Does everything its supposed to except get the clothes clean! Nothing gets clean, even on bulky setting when theres supposed to be more water in the machine!

We bought this at Lowes. Initially, they got the color wrong. It took two trips to get the right color (white) then a third trip because all the parts were not there to install the dishwasher. After a few months the second shelf rail end caps fell apart. Now, after a couple of years the pump goes out. RUN from this manufacturer.

I have had my Whirlpool W10280546B HE washer for 1 1/2 years. For the last year, I have had constant problems with the washer leaving a large amount of residue (in spots) all over my laundry. I have always run my washer as instructed, and I only used HE detergent in the correct amount. This residue appears to be fine lint, but may be lint combined with detergent.I have used the washing machine cleaning tablets and powders, but this has not helped at all. No one seems to have ever heard of this problem. I have to clean off these spots which cover approximately 1/3 of each article with every washing. The dryer helps get some of it off, but not nearly all of it. Any suggestions besides buying another washer of another brand after only 1 1/2 years?!

I found this site while looking for a part number for the thermocouple. Lowes had one, but not for the FG model. I decided to call the number on here from Chris to see where I could buy the correct one with left-handed threads. I was told that they would sell me the conversion kit, but I couldnt get just the $8 thermocouple. Then $47.90 later and the conversion kit is on its way. Im not happy about it but at least I got 6 years out of my water heater before the thermocouple failed. The plus side is next time, I can get the $8 part from Lowes and not be without hot water for a week.

The AquaLift self clean is a joke! Doesnt clean at all! Has to be consumer fraud, calling it a self clean. Ive owned electric self clean ranges for 40 years, that did great jobs. This does zip for cleaning! Unbelievable! Should be a rating below 1 star!

I called in a claim on June 10, 2016 & my washer is still not repaired. The extended warranty company, AIG sent L&W out to repair my washer. After 3 visits its still not repaired & the technician hasnt fixed it. Not only that he had laid it on concrete & scratched the outside. This is the worst experience Ive ever had with a warranty company or service company. Aig wont even return my calls. Will never buy a Whirlpool appliance again.

We purchased our Whirlpool refrigerator in 2010. A year or two after the purchase the side walls, draws, and shelves all started to crack open. We asked whirlpool to send new parts. They sent one and that cracked also. We will never buy from them again.

I like the Whirlpool oven ranges because it is easy to operate, easy to clean and like the features and functions. I have had no issues with the stove and I have had it for four years already. So far still working good.

We bought this Gold series refrigerator in 2013.. Less than a year we started having problems with rust on doors. It was so embarrassing people could see this. After that it was like one part after another, the motherboard, the ice on fridge, the ice maker. They changed the same part several times. Now April 2015 they say vapor cooling is not good and they have to put coolant and replace another kit.. Now we have to wait 1 week for that part. Meanwhile our food is going to go bad. Ive been calling for years about this lemon of a fridge. And the last time I spoke to somebody they say buy another fridge while youre waiting on the part to come out. Wow. This is literally driving my family insane.. I cant believe they just expect us to let this happen.. We paid about 2,500 for this lemon of a fridge.. I see so many complaints and youre telling me Whirlpool can get away with this.

We bought this product and had only had it for a couple of weeks when I spilled soup on the open microwave door. My mistake, but I would think that might happen to other people once in a while. The soup leaked around the window gasket of the microwave and streaked the interior of the door. It also ran down into the door of the oven and streaked the interior of that door. No way to clean this up that I know of without taking the door apart. I think these gaskets should not allow liquid they leak into the inside of these doors. Whirlpool says its my problem. They call it a use and care issue. I think its a design issue.

The beat goes on. My Cabrio washer is still down. After working for a mere 14 months, the control board died, and the machine would not spin out water. The repairman ordered a new one. Though the part arrived several days earlier than predicted, the repair service said they could not send anyone out, until our scheduled appointment. At last, today, the repairman arrived. I am ready to start whittling down the mountains of laundry we have stuffed in every closet. Some areas of my house are starting to smell like a locker room. It is not convenient for us to haul everything to a laundromat, or impose on a relative who lives nearby.The repairman was in the laundry room for at least 45 minutes, and then very apologetically tells us that the part is bad. It will not work at all. He has ordered a new one, and requested rush service, which I think they will ignore. I cant help but think these parts are manufactured somewhere outside the USA. Well, listen to this Whirlpool, I would rather pay $25 more for this part, and have your washing machine work. Dirty laundry might seem unimportant to you. It is not unimportant to us! If you cant do better than this, make something else. I am furious, and will spread this news to everyone I know, and I will report on this situation again.

We bought our washer (Whirlpool Cabrio) from a rent to own company about 2 years ago, and finally got it paid off. About a week ago, the lid started sticking when it was done washing. I went to open it last night to start some laundry, and it BROKE. Now theres a piece stuck in the bottom part of the lock, and the washer wont start. Anyone else have this issue?

My daughter bought a mobile home manufactured by sunshine mobile home co. in Red Bay al. The home is only 6 mo. old. In that home there is a Whirlpool microwave oven model # WMH2175XVB-1 Serial # TRY 20 23398. After 2 months my daughter microwave stopped working, Whirlpool sent a repair man out to fix it. He didnt have the parts to repair it so he left to order some parts that he thought might be the problem. When the repairman returned two weeks later with the parts, he replaced a door switch. The oven started to work. About 4 days later it quit working again. The repairman returned for the third time, tried repairing the oven and was unable. I had to help him remove the oven so he could take it home with him so he could try to repair it. At that time I was so angry that the Whirlpool co. would send a repair man out three times to repair something that was obviously junk. When I talked to the people at Whirlpool they told me all they were authorized to do was repair it. I explained the repairman has tried three times and couldnt and that they in good faith replace the unit. The answer I received had to come from a mentally challenged person. If this is the response of Whirlpool about their product, then I want no part of them in the future.

I’ve had this washer since October 2018. Worst purchase ever. It does not clean the clothes nor does it put enough water in it. I’ve tried the deep water option too and it’s for sure still not enough. I don’t understand how they even thought that this was perfectly fine to sell. If I could’ve taken it back a month after having it, I for sure would. And no one will buy it because they’ve read reviews of how it’s terrible. I wasted $900 on this washer. I have the dryer also which works amazing. The washer just sucks something terrible. My husbands military uniforms always look dirty and a lot of the clothes aren’t ever wet. I’ve finally seen a picture of how you’re supposed to have clothes in there. Why in the world would you only allow barely a layer of clothes at the very bottom to be cleaned by the agitator? Why would you have this huge drum only to put not even a load in there? This was such a waste Whirlpool and I’m glad I’m not the only person who has the same issue. I will never purchase another Whirlpool washer, it’s upsetting I can’t currently get rid of this crap washer I have now.

I bought a fridge from this company not even 14 months ago. Went away for a week and came home to a fridge and freezer of rotten food. The fridge had died - Im guessing not long after I had gone away by the look and smell of the food and house. I have had nothing but the run around ever since that day. Spoke to this person and then that person. The electrician confirmed that my fridge is completely dead because of the compressor. So they sent a report to Whirlpool and they have now confirmed that I will get a new fridge. Now Im being told that will take 7-14 days. So I have been left with no food whatsoever as well as no fridge. I have two kids and cant even buy shopping for my son to take to school. And now Im being told that I had 9 months left on the warranty for the fridge that died and that’s all I will get on a new fridge. Should I not receive a new warranty for a new fridge? And should they replace my food? Could really do with some feedback on this matter. Please help me.

RE: Our Whirlpool gas range/oven model# GW397LXUS05 installed Oct 2010 started acting up when setting the oven temperature. The 0 doesnt work so we input 355 instead of 350 etc... Other numbers have started to fail as well... Also it needs cleaning but a neighbor with the same model said whatever you do dont use the self clean for the oven, as they did & it literally burnt out the control panel costing them over $400!! Say what?? So we cant use the self-clean feature or well really fry the control board... Would LOVE to hear Whirlpools explanation on this one... And a minor issue but nonetheless worthy of a mention, the oven drawer never slides in/out properly & hasnt fit right from day one...

I filed a complaint late Oct. 4, 2011 about a problem I was having with one of my Whirlpool water heaters. Chris from Whirlpool emailed and phoned me twice within 12 hours! He was courteous and very helpful. He shipped the parts that I needed overnight. They came in this evening, I installed them and everything is working great! Thanks to Whirlpool and Chris, we now have hot water!

Bought this washer and dryer on sale at HD. The washer hasnt worked from the beginning. The clothes dont get wet because its an HE. I have to add buckets of water to even get the clothes wet enough to wash. The clothes come out with a residue on them. We use liquid HE detergent. It appears Im having the same problem as the majority of posters here. I will NEVER buy another Whirlpool appliance. There should be a class action suit to get Whirlpool to respond.

I like the looks with brushed stainless steel and black. The most difficulty was getting someone to help get it and load it. But other than that, Ive had no problems with the dishwasher.

I purchased a Duet Dryer less than a year ago and it stopped working. Got the warranty people to send someone to diagnose it. The repair person ordered two parts to fix it (they took the control panel off the order for some reason). They sent a second inept person to try and install the part they did send and it did not work (He was the most condescending person I have ever met but that is another story.). Of course it did not work and they actually have to replace the control panel AND the electrical panel (which as you know was ordered by the original tech, but taken off the order by who knows?). Now they are telling me that the part that they should have ordered 2 weeks ago is on back order until sometime in May. All I am getting from Whirlpool is lip service and they honestly do not care one tiny little bit that I have a dryer under warranty that will not have been working now for close to six weeks. This is unacceptable business practices.For the record I bought the unit at LOWES and they too refuse to stand behind the product. Basically told me tough they have nothing to do with it. I also purchased an $8000 Kitchenaid (Whirlpool) Refrigerator 5 years ago and the control panel went out about 4 years later. They stopped making the part and I have to THROW away an $8000 refrigerator because they dont make the part for it. As evidenced above, Whirlpool products do not stand the test of time and when they do break (even under warranty), they cannot fix them in a timely manner or at all in the case of the refrig (not under warranty). I caution every reader of this diatribe to choose wisely WHERE you purchase your appliances and carefully select a brand other than Whirlpool (and its brand affiliates of Kitchenaid, Jenn-air, Amana and certain Kenmore products).

We purchased the gas slide in range with gas oven. Immediately the temperature would hold a consistent heat, therefore it continually reset with a start sound (swoosh) every 5 minutes. The manual says it will do this, but clearly this is not normal. Then, the oven stopped working, showing an error message FBE0, that the cooling fan is not at high enough speeds! It sounds as though, along with hundreds of other people, we have all been ripped off! If anyone can please tell me what can be done about these defective stoves, I would appreciate it, thanks very much!

I purchased a Whirlpool Microwave on 9/21/10 from Hamilton-Bryan in Wichita Falls, Texas. I had a small fire in my microwave on 9/19/11, due to a faulty mica board. This was replaced by Mr. Bobs in Wichita Falls, TX, under the warranty. Then on 1/9/12, the microwave would not warm anything. I called Mr. Bobs again, and they said the transformer was out. I called Whirlpool, and was told by Yvonne that Whirlpool would replace the part only, with no labor, but Mr. Bobs was closed, and to call back in the morning, so this authorization could be set up with Mr. Bobs. I called back and there was no record of my call with Yvonne. I talked to a supervisor Rachel in Tennessee. She put me on hold for a while and finally said she found Yvonnes note to authorize the part. I explained to each person I talked to that I was dissatisfied with Whirlpool. I believe I have a defective microwave. I would like my money back, or a new microwave. I believe the defective mica board is related to the defective transformer. I am a very dissatisfied customer. I have used Whirlpool most of my adult life. I have used them since the 1970s. I currently have a Whirlpool refrigerator, washer, and dryer. A similar situation like this occurred when I bought a Samsung washer. I was dissatisfied, and Samsung refunded my money, and I bought a Whirlpool washer to replace Samsung. I will not be satisfied with this situation, until the microwave is replaced. Thank you for your concern and attention to this matter.

Purchased this washer in 2009 from Lowes, believing the hype that it was efficient. Since we only needed a Washer at the time, we overpaid (it is more cost effective when you buy both washer and dryer). So we paid $1000.00 for this machine (we purchased the stand as well). After the 1st year, there seemed to be a significant decrease in how fast the washer spun, as the clothes were coming out wetter. I didnt pay much attention, but 2 years later, the machine has a weird problem where it couldnt complete the cycle, and by this time, every time it Spun, the noise was louder and louder.I contact Whirlpool, placed a service call and the Technician came out. $225.00 later, there was a hose that was pinched that was sending a wrong signal to the washer. He fixed that and told me I should get a contract on the machine through Whirlpool since I seemed to be having problems. I purchased the contract, for $300.00, and 2 1/2 weeks later placed another service call, as the noise from the machine was happening every time I did laundry. The service guy came out, indicated that it seemed to be the Agitator, and that he would need to order parts, and that they had a SPECIALIST who only does this type of repair, since they have many! He also indicated that the hose may have crimped due to the movement of the entire agitator!Well, after not hearing from ANYONE for 2 weeks, I called the repair company who told me WHIRLPOOL was supposed to call and let me know that they would NOT fix the machine, as the parts cost more than the Washer, which is now valued at $500.00! No one from WHIRLPOOL EVER CALLED, and I cant understand how a $1000.00 Washing machine touted to be so efficient and environmentally friendly has been THROWN OUT after 3 years!!! And now I am out the $225.00 repair, have no washing machine, $1000.00 down the drain (and I forgot to mention a year later we bought the matching WHIRLPOOL DRYER and OVERPAID) and now have to purchase another machine, which I assure you WONT BE WHIRLPOOL! As most of us have experienced, WASHING MACHINES last for many years! The washer I had before this was over 20 years!!!! So much for efficient and environmentally friendly... The only thing GREEN about this machine is how much of my $$$ has gone to Whirlpool!

It gets the job done. Its no power washer, but the dishes get pretty clean and dry nicely. I have no idea how dirty the dishes can be and still get cleaned, since Im weird and pre-wash my dishes. Its stainless steel and black, and has quite a few wash and dry settings, including an option for heated or unheated dry. The utensil rack is attached to the door of the washer and cant be moved. Two levels, and pretty easy to do dish tetris with. No offense to most standard dishwashers – I need a washer about 3 times the normal size due to a passion for cooking. Its slick and matches my ultra-modern, borderline-Swedish interior.

My Whirlpool Cabrio washer (WTW6600SG2) is a money pit! After reading all of the nightmare stories concerning this washer one would think Whirlpool would offer a recall and try to correct their wrong doing. Do not buy a Whirlpool Cabrio. It was the worst decision I have ever made! Whirlpool does not stand behind their products. I cant believe they can get away with treating their customers so unfairly, taking their hard earned money for crap like this, then not offering to help after so many have had issues. The Cabrio is loud, doesnt get clothes clean, and is always flashing UL for uneven load (when it works at all). My local repairman has made many trips to fix my problem Cabrio. This time he is at a loss. Ill be buying a new washer and it will not be made by Whirlpool! Please, if you are reading this be forewarned!! You will regret your purchase if you buy a Whirlpool Cabrio.

I decided to buy the Cabrio. It was the most expensive, but I wanted to buy American, and I liked the set. It does not do great with cleaning the clothes and they smell when they come out of the washer. Do you have any suggestions. It does not fill with enough water even when using the deep water mode. Please help as I would not recommend this. I called Lowes where I bought it, and they said they knew, but are not recalling, or making any adjustments until Whirlpool does.

I bought A Washer Whirlpool and right after 30 day of the purchase my washer went bad and I called the Whirlpool Services and they told that will take about 30 days to come out and take a look at it. Are you crazy!!!! Freaking garbage that is what is. Never would want to buy Whirlpool again specially with that type of customer services they have..

I myself cannot believe this. We remodeled kitchen in 1992. Gradually we had to replace the appliances except Whirlpool dishwasher. It still works okay. Only sometimes the detergent tablet does not dissolve. Anyway after 21 years, we are replacing it with another WP dishwasher.

I have had this refrigerator for 23 months. The ice maker has been a continual problem. It overfills and water runs onto my hardwood floor. After four service calls for the ice maker, the defroster heater caught on fire and melted the interior wall of the freezer. Not sure if we fixed the ice maker since we had the fire four days after the last service call. My service rep declared the refrigerator unrepairable. Fortunately I had purchased an extended warranty and they refunded 85% of the purchase price after 2 years of use. Besides the ice maker problem and the fire, I also had trouble with food freezing in the refrigerator compartment. I dont recommend this model, but my repairman says that Whirlpool is as good as it gets.

Washing clothes is a nightmare. I am constantly removing clothing from the washing machine that have been torn and left with holes. I am utterly frustrated. Because the machine is more than three years old, there has been no solution to my problem. I have now replaced clothing items in excess of $2,000. I am always here that they will send a repairman and yet there is still the problem. This machine is costing me too much money. The newer machines have fixed the problem. There is no gap between the drum and the doorway or rubber piece. I want that piece to stop this nightmare. This machine has taken a dream of mine and demolished the experience. I hate washing clothes but more so having a machine at home and then going to the laundromat to stop the chaos with doing laundry at home.

I have the Cabrio washer that is only four years old. It is leaking oil and is very loud during the spin cycle. I paid $800 for this washer and am extremely frustrated that it didnt last longer than this. I contacted Whirlpool customer service and had no luck since it is out of warranty. Due to the high number of complaints with the same issue, please consider a class action lawsuit. Thank you.

I would like to share whirlpools lack of ownership for parts they knew were faulty that caused significant damage to my floor. Its absolutely horrendous that one would purchase the highest end dishwasher they offer (all highest end appliances in 3 homes so far) and the company is only willing to cover the replacement of the part. Its a horrible way to run a company. I hope that my review will warn prospective customers to stay away from a company who is only willing to take your cash at purchase (charging an arm and a leg no less) and not care about any repercussions after the fact. I hope they enjoy our 15k, because it will be the last penny they get from us.

My Whirlpool stove and oven have been absolutely wonderful. My Appliance is 18 years old and Ive never had a problem with it since the day I bought it. I recommend Whirlpool appliances for the whole house.