Two-year old Whirlpool Cabrio top load washer; absolute piece of junk! Bearing on the drum howls like a train. Now the master board or some other sensor (under drum) is out. Serviced for the third time and the service repairman states its cheaper to replace than to repair. For a 2 person household, it is reasonable for us to expect more than 2 years from a washing machine. Same experience with Whirlpool 15 years ago. 1st time shame on you; second time shame on me.

We bought a new house and the choice given to us was Whirlpool. After the first year in the house we had a $300 repair. The control panel inside the fridge went. Pretty poor performance.

I purchased a Whirlpool hot water heater several years back with every bit of the Bells & Whistles that Lowes could bestow on it paid for and documented on the tank; Limited Lifetime Warranty and Lowes Professional Installation. It failed after several years with multiple problems. First, the bottom heating unit failed at the same time, noticing a leak from the top heating units external cover where a supporting screw had popped out, leaking down to the floor. Not only was the Whirlpool 800 number a scham of silence, with no estimated wait time and after approximately 20 minutes, a rep picks up as I could hear their legal department on an alternated line instructing and listening in, then dropping off when those crooks felt I had been placated enough to go onto to the next sucker. I have all Whirlpool Gold & KitchenAid Superba appliances in my kitchen and never thought I would be saying this but I will never purchase another Whirlpool Appliance or shop at Lowes again!

I went to get ice from my Whirlpool Gold refrigerator, model GB2FHDXWS, and found it was melted. Light and fans were working. I had to throw out all that was in the freezer drawer. I called Lowes service and reported that our four-month old refrigerator wasnt working. They sent a food claim number and set up a service call. Then, the lady said to unplug it and plug it back in. We had since cleaned it out. I unplugged it and plugged after a minute and it came back on. The Ace service guy called to confirm his schedule. After hearing that it is running again, he said they are computer controlled and unplugging it and plugging it back in reboots it, as you might reboot locked up PC. He also said that since it is now running, Whirlpool wont stand behind a service call. He said wait until it does it again. Now thats just jim-dandy. We have an expensive new Whirlpool Gold refrigerator that has computer controlling that cant be trusted as the control may or may not lock up in the future spoiling the stored food.

GFG461LVT2 - In October of 2010 I purchased a Whirlpool Gold Fridge and Stove. Its been about 3.5 years and two of the caps that go on top of the range burners are chipped. All of the caps are badly stained and despite the manual instructions to wash them in mild soapy water, they do not come clean. They dont come clean using heavy duty Easy Off cleaner. In addition, the seal on the oven door has apparently failed because the glass is foggy on the inside. Today I phoned Whirlpool after going to their website. I first spoke to a parts representative who advised that I would have to pay $47.00 per cap or $115.00 for all five burner caps. I was transferred to another department as I thought I should get the appliance parts and door fixed for free. The appliance is only 3.5 years old. I was told that the appliance is only guaranteed for 1 year and I would have to pay dearly to remedy the two problems. This appliance is Whirlpools Gold series. It supposed to be top-of-the-line - the price tag was certainly top of the line. Im very disappointed in American workmanship and the companys lack of integrity. Not too long ago I purchased a Whirlpool (aka Maytag) front loading washer. I now own a Samsung. The point is that designed obsolescence will force consumers to purchase products made outside of the US because some of us cannot afford to buy or repair appliances, cars, etc., every couple of years.

Purchased WP fridge, stove, and dishwasher at the same time. All were the gold series. At 20 months, freezer stopped cooling. WP would not cover the repair. Refrigerator has been noisy from day one. This company does not care about their customers.

We have had our Cabrio for one year now and we found the agitation cycle to be loud but we have gotten used to it now. The thing we cannot get used to is the sour smell permeating from it. It smells like a dirty mop. Our washer and dryer are in a small laundry room so when we enter it to get to the garage or bathroom, the smell hits you like a ton of bricks. Stinky!!

I bought a NEW Whirlpool 40 gallon, natural gas hot water heater from Lowes in May 2012. January 04, 2014, the main electronics failed that controlled everything. It has a 9-year warranty (after 1 yr.- parts only). What failed was the Gas Control/thermostat unit, and it takes a HVAC-trained person to replace it. Yes, theyd send the part - free, but required me to pay for installation. Talking with an HVAC business owner, he said hes replaced about 30 of these and he surmised that Whirlpool KNOWS that nationwide, over 10,000 needed replacement yet Whirlpool cares less. Ive had trouble with other Whirlpool products, so when my appliances, etc. go bad, I will NOT replace with Whirlpool products.

Purchased from Home Depot and self-installed. That part was not too big a deal but after installing this stove we started a journey of irritation, aggravation and general dissatisfaction. This stove has the standard layout for burners that seem to be common to most low-end stoves. Two huge burners in the front, a simmer burner at the right rear and a general purpose burner at the left rear. Thats all wrong for me and our set up. I want a large burner at the left rear and general purpose every place else. Can you alter the standard configuration? NO! Not without some major alterations to the stove top.Next are the grills or cast cooktops (2 each). They are a bit cumbersome when cleaning the stove but doable. The real problem with the grills are Whirlpool decided to save money by skimping on this feature. The grills are not a stable cooking platform for smaller pans and it turns out Whirlpool recommends square pans for this stove. SAY WHAT? I have pans and skillets from my grandparents and they are ALL round. Thats how that stuff is made. ROUND! The grills design is unstable for any round pot, pan or skillet, if its diameter, is 6 or less. Kiss that excellent saucepan goodbye if you have this stove. My current solution is a piece of light expanded steel over the burner areas.Keeping in mind we use Propane as our heating gas. The adjustment of the flame temp on the four burners is non-existent. They all are either on high, medium or low. There seems to be no fine tuning with these burners. At the end of the day go look for something that is NOT a Whirlpool, LP gas range Model #: WFG515S0EW. You will be better served and less irritable with almost anything else. Even a campfire in the yard is a better choice.

I have a Whirlpool suite. Stove is fine...refrigerator is awful. Froze all the food in fridge. Cost me 100’s to replace. Put in new thermostat. Now sounds like a freight train. Bought in April and the filter already needs to be replaced to the tune of $81.

I would like to extend my appreciation to Whirlpool for quickly responding to our requests. Within a matter of days, we were contacted by a Whirlpool corporate representative. She listened to our issue and was extremely understanding of our frustrations. The representative assured us that we were valued customers and offered to contact our local service provider and authorize the needed repairs to our refrigerator. This interaction has restored our faith in Whirlpool and its partner brands. The representative also provided guidance on future purchases in contacting Whirlpool to purchase its extended warranty.I would suggest using Whirlpools warranty program instead of a retailers program. Contact Whirlpool to purchase any extended warranties directly, instead of purchasing an extended plan at the time of purchase. Thank you to Whirlpool and to our extremely helpful representative. I am not including her name, to protect anonymity.

I like the Whirlpool oven ranges because it is easy to operate, easy to clean and like the features and functions. I have had no issues with the stove and I have had it for four years already. So far still working good.

Whirlpool Refrigerator: Model # WRT111SFDW - We bought this frost-free frig. in Feb of 2016 and this Feb. before the year was up, it started freezing up. I called the Co. and they sent a young man to my house to fix it and he thought he had. Well 2 wks after that it started freezing again and I called the Co. again and the same thing happened again and this was after my warranty had expired. Well then this young man came out and replaced the fan and a heating rod I believe to help it to stop freezing. Well 2 days ago it started freezing up once again. Im disabled and live on a fix income so now Ive got to figure out to get me another frig. And it WILL NOT BE A WHIRLPOOL REFRIGERATOR. But kudos to the Co. and the young man for trying to fix it even though it took 3XS and still not working.

After insisting to my husband that I wanted an HE washer with a large capacity so I could wash comforters and such and be ready for a house full of grandkids and visitors (we recently moved and had to leave my washer and dryer in the old house); I have been very disappointed with the washer. It leaves lint residue all over my clothes! Some of them I just cant get off. I live in Colorado and the sun shines almost everyday! I love to hang my clothes outside to dry and get brightened by the sun. Being a mile high makes the clothes even brighter I think!Anyways... back to washer... I have been doing laundry for 40 years. I have 4 grown children and know how to sort, etc... When I wash my darks, the lint that ends up on the shirts and pants... its just ridiculous! I end up scraping it off for about 25 minutes before I can hang them up to dry. On some of the clothes, there are marks where all the lint was and has stayed! Ive tried using less detergent, less fabric softener and always use the extra rinse. Tried setting it on the lowest spin cycle and the highest... Nothing helps. How do I tell my husband I would like to get rid of this and get an good old fashioned washer? I was a maniac for two months doing research and making a great cause to buy these machines!It seems to be a little better if I dry the clothes in the dryer, as the lint is pulled off somewhat, but the marks remain. If anyone has had the same experience and knows what Im doing wrong, or has a solution (other than going back to the basic machine) I would appreciate it so much. Disappointed in Denver.

Light bulb went out in the freezer. Come to find it is a led cluster with a circuit board only cost $30 to $100. Engineer should be fired. What is the reason to take simple bulb and custom bastardize into an expensive hybrid. Greed.

We bought a Whirlpool washer in 2010. It started making a loud noise on the rinse cycle in 2012. We called Whirlpool. They sent out a repairman from A and E Repair. Was told tub bearing shot, repair over $700.00. Contacted Whirlpool, was told machine out of warranty. After talking to them, they agreed to send parts if we paid labor. Machine lasted less than a year making the same sound again. A and E sent out same thing, bearing gone. Repair cost $997.17, charged us $136.74 service call after 2 minutes to shake the drum and saying same problem. Was told by Whirlpool, no warranty, tough luck.

Although we live in Canada, we purchased our slide-in oven at Sears Roebuck in Buffalo, NY only because of the size availability only in the US (actually, the unit was manufactured in Canada as we found out later!). Obviously, this created another problem since the unit was not underwritten by Canadian Electric codes, Sears Canada repair would not touch it! Once installed, it worked great until the first problem with the oven quitting after self-cleaning. It is the second time in 3 years that both the thermostat and the sensor went in this RBS245 slide-in oven. Once the self-clean cycle completes (quite smelly!) and cools, the oven does not operate rendering the oven useless. First time, in 2009, Sears repair only suggested (since they would not do repair on it for reasons stated above) which parts could be faulty: Timer, sensor, thermostat or elements. It was thought to be the electronic timer unit, which was replaced at a $215 (needlessly) because that was OK. Both thermostat and sensor cost $150. Even the elements were replaced, $52. The second time, just a week ago, exactly the same happened. I replaced the 2 items: Sensor and thermostat at a cost of $154 and the oven worked fine again. I called both Whirlpool US and Canada, but no one could/would give any answers why this happens.So far, it cost $600 in parts to repair! This is nonsense from a company that has had good reputation and record. Obviously, that is changing! If Whirlpool cannot engineer a product that works as they say it does, they should close the shop! Reading here, there are others who complained with the same problem. It is time for Whirlpool to come clean!

My Whirlpool refrigerator model #ED5FHEXV001, serial #HR0248 - I have spoken to a couple of reps on the phone. I am very dissatisfied because it was like one rep I spoke with on the telephone advised me to buy an extended warranty and at that time, the company would consider alternative ways to deal with this complaint and perhaps replace the refrigerator. I did not want to pay an additional $100 for a warranty, unless the company would guarantee me a solution, preferably my money back. I did not really believe the warranty would help me after the warranty was expired. I would still have the same problem and I feel that in the event after the extra warranty expired, the company would tell me I should have kept the coils clean, which is my complaint. There is no way to keep the coils clean. I guess blowing out the residue, then all that residue material would end up all in my house. Also, very important, there have been 3-4 technicians to my house the first year. I was told various things to do, such as adjust the refrigerator to a lower setting and freezer to a little higher setting. One tech actually replaced a part? The second tech said he would clean the coils. The last tech told me the problem was my coils had to stay clean. My question is, how the heck is that possible with the coils on the bottom of the fridge and susceptible to a lot of dust and dirt, unless I move my fridge everyday? Most people do not expect to have to clean under the fridge each day and the coils would still be dirty anyway. It is very dumb that the coils are not on the back of the fridge. With the fridge coils on the back, I have never experienced this problem. Please advise what my next step would be. Thank you.

We purchased a higher end cabrio model only 3 years ago. Last year, on about every 5th cycle, the load would not spin at the end. Id have to remove all the wet clothes, set it to drain and spin, start it and wait for it to hopefully kick in. When I do it right, it kicks into the spin mode. I had to quickly press start/stop to unlock the hatch and reload the soaking wet clothes and wait for it to spin properly. Yesterday the same thing happened again. This time, it did not kick in. I ended up flipping the washer over and taking a look underneath. I discovered that the motor was seized. It had lost all its lubricating oil and smoked the belt. Now, my 3 year old washer is sitting in the driveway awaiting a trip to the dump since I got fed up and went out and purchased a new Samsung top loader. I emailed and called whirlpool with no luck. Not impressed. When I went out to buy a washer today the first thing I told the salesman was to stick anything with the name whirlpool out in the trash bin out back.

I recently purchased a Whirlpool Slide in Oven replacing my Amana stove of 15 years. My Amana was a very basic model, and I thought this WP was an upgrade. But it is so poorly made its ridiculous. First of all the bottom storage drawer, is so flimsy, it does not slide out easily, and the top lip doesnt even have a finished edge. Additionally there is a 1 inch gap between the top of the drawer and the bottom of the stove door. But the BIGGEST disappointment was the oven racks, totally flimsy.We used a Lodge Dutch Oven (which we have used many times with our old stove) and the oven rack sagged under the weight. Had I known I would have pulled the racks from my old stove. I contacted that seller about these issues, and they said they are ALL like that even the higher end ones, and I contacted Whirlpool to see if I could buy better quality racks and they said no, this is all they have.

I bought Whirlpool gas water heater on July 2009. It keeps going out. It is not working. I found out you cant even get parts for fixing it. The dealers told me its junk. I was told to buy a new one. Then, I found out its been in class action lawsuit. How did I get to buy it after it was recalled? I dont know what to do.

We purchased a Whirlpool Duet machine in September 2010. About a year ago, I started noticing tears and stains on clothing. Luckily, it was always on a washcloth or blanket, nothing special. Last week, it tore a 3-inch hole in my good jacket. I was not happy! My husband and I checked inside the drum and all around the seal. Neither of us found any rough edges. I thought if I called Whirlpool, they might have had a recall. They assured they had never heard of this problem. REALLY!!! Just look at all these e-mail complaints. Back to the old top loading - basic wash machine. Definitely not a Whirlpool!!!

There is a chronic and well-known problem with recent French door, bottom freezer refrigerators sold by Whirlpool, including the the brand names KitchenAid, Jenn-Air, Maytag, and Amana. The problem is caused when the defrost drain freezes, preventing defrosted water from reaching the evaporation pan. After enough water builds up, it overflows along the front of the refrigerator. In my particular case, we have wood floors and they were ruined by the water. After doing some investigation on the internet, I have learned that this problem affected approximately 1,500 model numbers sold under these names. These model numbers are listed in a Technical Service Pointer issued by Whirlpool.In August 2013, after experiencing several years of problems with these units, Whirlpool issued a Technical Service Pointer W10632338, advising service technicians that a new P Trap drain tube kit was now available, and suggesting that the defective duck bill check valve should be replaced by this new part. The problem for years had been that the rubber duck bill check valve would, over time, become sticky (or tacky) and would then not open - causing water to build up above it. Eventually, the water would freeze and since newly defrosted water could no longer escape, it would build up and eventually overflow.From what Ive seen online, plus a conversation with the Sears technician who come out to diagnose and repair my leak, I am convinced there are many thousands of customers who have experienced this problem. Because it takes a while for the rubber check valve to become sticky and no longer open, it is not uncommon for the problem to not appear until after the standard one-year warranty has expired. From reports, Whirlpool has sometimes acknowledged the problem and effected repair of refrigerators no longer under warranty.But what about those customers, like me, who have experienced water damage to floors and cabinets? Shouldnt Whirlpool be liable for those repairs, too? Id be interested to know if anyone knows of plans for a class action lawsuit.

Maybe they make some higher end ovens but ours was not one of them. The oven light fixture works intermittently and its only been 8 months that we have had it. The insulation on the oven is lacking as well. You can turn the oven off at 450 and within 15 mins its already below 200.

We bought a Cabrio washing machine two years ago. I have had to have a repairman out twice for it shooting water out of the top (from a top-loading machine). They repaired that and its better. But this goes off balance ALL the time. I cant even wash a load of towels without it going off balance. We bought this one as it was supposed to handle large blankets and even my lightweight king size comforters. Yeah. Did once or twice, then started the off-balance stuff. It grows MOLD in the bleach, softener, and detergent dispensers.I wrote to the company and included pictures. They were really rude about it. I finally found how to remove the dispensers to clean them, but it is very difficult. I HATE this machine and will never buy a Whirlpool again. (Our refrigerator, which was in our house when we bought it, is also a Whirlpool. It is poorly designed and collect dust in the coils UNDER the thing and you cannot reach them to clean it. Coils are behind other pieces that block being able to clean them.) Whirlpool is a horrible company and doesnt stand behind their products, in my experience.

Avoid Whirlpool at all cost. I have had the GSS series, which was horrible. It was declared unfixable by service after 2 weeks of ownership. It was replaced with a similar WP model WS series and was told it was basically identical to the GSS series except for some cosmetic differences (They do look identical and yes, it’s just as horrible as the GSS.). The first one was defective from day 1. It was replaced and assured the next one would be thoroughly checked out prior to delivery. Obviously, nobody did this (was still in box and never opened). The fridge arrived and had the same exact defects as the previous units. Service literally said these were junk and they had nothing but issues with them that they simply cannot fix, and issues Whirlpool is obviously aware of but will not admit to, nor back up their products. Service literally told me to avoid WP at all cost or I will have nothing but non-stop issues and non-stop service calls and the fridge will still not be fixed. I purchased the extended 5 year warranty that clearly states that the fridge will be fixed or replaced if deemed non-repairable. Mine was! Yet, neither Whirlpool nor the retailer will do anything. I was literally told Take it to the dump and go buy a new fridge by both Whirlpool and the retailer. My purchase was less than a year ago. The 3rd fridge has only been here 3 months. They took my $1,500. They took my money for the extended warranty. It has been declared non-repairable, yet Whirlpool’s and the retailer’s response is Too bad, we are keeping your money, not honoring the warranty. We don’t care if it’s non-repairable. Take it to the dump and buy a new one.This is new! The money it cost, the money for extended warranty, the money for lost food, the money for lost wages due to having to be here for repeated service calls, the huge amount of time spent using hair dryers and everything else under the sun (this fridge must be baby sat and monitored pretty much 24/7 due to more issues than I can list). The fact this fridge has taken over my life, with freezer and fridge unusable (totally unusable, it has taken over my life, but I still can’t use it and spend a fortune getting take-out food) is just shocking, but more shocking is the fact neither WP or the retailer (the blue one that starts with an L, ends with an S and competes with HD the orange store) will stand behind the product or the warranty and instead is telling me to flush multi thousands of dollars down the drain and take my new, with extended warranty, to the dump and buy a new one. Calls to both companies only led to more wasted time and frustration.I don’t even see how this can be legal. They happily took my money. They fully explained how I needed the extended warranty in case something like this happens and assured me the extended warranty would protect me in case something goes wrong for 5 full years. They will replace it with a new one if un-repairable. Yet in less than a year, Ive gotten 3 defective ones with the last one only 3 months old with the first service call made on the day after delivery, but I’m supposed to throw all this money down the drain, take my new fully warranted fridge to the dump and buy a new one?!Shocking and not something I can afford to do. If I could afford it, I would get this thing out of my house in a heartbeat and buy something else, but I’m not made of money so this is not an option. Not sure what I can do other than to warn others to avoid Whirlpool and avoid the retailer (L---s). I’m just in shock and to say I’m upset would not even come close to describing my utter disappointment and frustration with both companies and this whole ordeal (never ending nightmare is more appropriate).

My Whirlpool refrigerator is about 13 months old and the paint is peeling off. I was told my an associate at whirlpool that I could have a service person come replace it for approximately $500. And this is only for one door not both.

This Whirlpool is great with a side by side refrigerator and freezer. I love the ice maker and water on the freezer side door. The refrigerator keeps my veggies and fruit fresh and crisp. Has a water filter purification that makes the water taste like mountain spring water.

I purchased a Whirlpool induction cooktop Aqualift self cleaning oven Nov.1/12. The oven has never been easy to clean you always have to scrub it, now I boiled some pies over in Oct/13, the syrup burned into the bottom of the oven before the pies were finished baking. My oven is now pitted, warped, and bakes very unevenly, have contacted the merchant, Saskatoon Appliance, Whirlpool, and Excelsior Insurance (extra warranty) Insurance guarantees 24-48 hr service but to no avail. We still have no service 1 month later.

I purchased my Whirlpool Duet in 2007. I have since paid more than what the washer costs in repairs. Now, the metal that braces the basket has corroded and fallen apart. Ive read that this has happened to many people and since then the company has changed the part. However, they are unwilling to send a new part to me. I will never buy a whirlpool appliance again.

This dishwasher does not clean the dishes. Having said that most of the dishes are too oversized for the small capacity. Perhaps the fact that this is such an old dishwasher. I’m not sure but none of the dishes get washed. About the only thing that works is the dryer heater. Sorry to say, I’m not happy with this dishwasher and wouldn’t recommend it to anyone.

Our washing machine - as part of a stackable set - is two weeks beyond the one year warranty. Washer breaks down, I order the replacement part to find out - after waiting two months for the part - that the washer is now being discontinued so the ETA on the part is NEVER. Ask what Whirlpool will do about this and am advised that they will offer me a discount on a washing machine that does not fit on the stackable dryer. Or I can purchase a new washing machine at more than the original cost of the stackable set.This is a totally unacceptable situation. The washer is just out of the one year warranty period and it is already being discontinued??? Is Whirlpool making disposable appliances now so that after the one year warranty we just toss the appliance in landfill? Really? Unable even to purchase replacement parts to repair a one year old appliance? I will think long and hard about ever purchasing another Whirlpool appliance again.

Dont know the model but it is a basic smooth top range without self-clean option. Its easy to use. I like that it has a smooth top which is easy to clean. I didnt need to pay for the self-cleaning feature as I use an oven liner and clean it right away if I need to. When we went appliance shopping, we needed to replace all major appliances. We chose Whirlpool as we have had them before and they performed well. Also bundling a group of them allowed us to get a great deal.

After 50+ years of doing laundry, I had to purchase my 3rd washer. I bought the new top loader without an agitator. I very quickly learned that it has no lint filter. My first load was towels and mats. The lint clogged up my tub and drain pouring water all over the floor. Since then it has ruined many of my clothes which are mostly sweaters and sweater-knits. Without a lint filter, it deposits the lint right back on the clothes where it stays forever unless I shave or pick it off, even though Ive turned them inside-out. (Time consuming waste!) Even my socks have little balls of lint. It seems the only safe fabrics are new, smooth woven cottons, cotton-blends and slippery nylon providing there is no lace or brushed elastic.Now to the no fabric-softener dispenser... The Downy ball simply doesnt work, and theres no other way to add it. Waiting to use dryer sheets is too late; the damage is done. My clothes are dingy. In my 50+ years of ownership, I have never had to purchase a separate product to wash my washer so that it doesnt stink... and it does. Why does it lock after starting? If I could afford to replace it, I would... but I cant.

My stainless steel french door refrigerators compressor quit working and needed replaced after 3 years and 10 months. I had to buy a replacement kit and it cost 400.00. The repairman cost 175.00. I tried to buy an extended warranty but they do not sell them. You get a 1 year warranty. The repairman told me you will be very lucky if you get 4 years out of the replacement. He said all of the new compressors are really junk. Remember when refrigerators used to last 30 to 40 years. Not anymore. It is a money racket. Do not buy anything Energy Star, it is all junk. I have gone through 5 washing machines in 18 years, and I live here by myself.

I have called numerous times to complain about my new Cabrio washer. The first thing the employee did at the service center was to send me an owners manual, which I did not receive when I purchased the washer at Lowes. I followed all of the washing recommendations and still had problems with soap being left on the clothes. I called again and they said that perhaps there was something wrong with the washer and they were going to send a service technician out. I told her that he would probably not find anything wrong with it. I was just very unhappy with the product. She told me that we should check it out and not to worry. It was still under warranty and Whirlpool was going to take care of the service call. The technician told me that they have received many complaints about the machine, but there were no fixes available at this time. Yesterday, I received a bill from the service company for $129.00. I called the service company and told them that Whirlpool should be billed for this, not me. She told me that I had to call Whirlpool and if they wouldnt take care of it, I would have to. I then called Whirlpool, only to be told by the customer service rep that since they didnt find anything wrong with the machine, there was nothing that could be done. I asked to speak to someone else and she let me talk to her supervisor. She pretty much repeated what I was told by the first person and it is in the owners contract. I told her that I wanted to cancel the extended warranty that I just mailed in this week and she gave me another phone number to call. I cannot express how unhappy I am with your customer service department; the lack of compassion your company displays; and how I was told one thing and then charged a fee. It would seem that you have no eagles working for your company. I cant believe that a company as large as Whirlpool does not stand behind their products.

I purchased a Whirlpool Cabrio washer in 2007 and had to replace the control panel for $300 each time twice.

Refrigerator Model ED5FVGXWSO2 - After owning it for a couple of years, we decided to do a super cleaning and remove all the shelves. When we took the shelves out, I noticed that the plastic support tracks were all cracked. I called and complained to Whirlpool and of course the fridge was out of warranty but heres the good part - The person on the phone asked me Did you put heavy things on the shelves? OMG My response, trying to think of the heaviest thing possible, was, Like milk cartons and juice? She even said There was likely a bad batch of plastic when the shelves were made. I was a big fan of Whirlpool. Great value etc. but I will never buy from them again. Shelves should last the life of the fridge!

Whirlpool Cabrio Model WTW6500WW1 - Have had good luck with previous Whirlpool Washers so thought I would purchase this one 2 years ago from Menards. Paid more than I normally would and thought it would be worth the extra money. Not so.......As many others, it has a foul odor that will not go away and now sounds like a freight train in the house. Called Whirlpool about this issue and parts are not covered. Total cost of parts including the tool that is needed for this repair is $187.00 not including shipping. Whirlpool has lost my business moving forward as like many others, Im sure. Very disappointed!

We purchased our suite of appliances from Home Depot, this was a great experience. Unfortunately that is were it stopped. Our 1st refrigerator caught on fire in the electrical within the unit. We got a 2nd refrigerator sent to us and it came damaged. Then they sent us a 3rd refrigerator and it caught on fire in the electrical as well. Weve been dealing with this all since August 27th 2019 and here its now October 14th 2019. At this point I feel this model of Whirlpool is truly unsafe.

I feel as though they could use some additional features, it’s also hard to change out some of the wiring in the back. I’ve had some issues with smells coming from the washers as well from them. Hopefully they can start to look into tweaking smaller details to improve the overall machine.

I am a single parent. So I was very excited when I had saved enough to purchase a new washer and dryer. I purchased Whirlpool because I had been told that was a good brand. From the beginning, I was having issues with the washer (Whirlpool Front Loader model #WFW8300SW04). It wouldnt start or it would not spin, or it would just lock and not be able to get it open. I had purchased a warranty. So I called to have it serviced. The tech came and told me that I needed to have my floor leveled under the washer. I hired someone to concrete under my washer and dryer. Again the washer still did the same thing. I used the warranty again. The second tech told me that I needed to have my electrical outlet changed. I again hired someone to change the outlet. Yet still the machine didnt work. I then hired a tech to come out and was told the mother board needed to be replaced. Had that done. The machine worked for a short time with no issues. But yet again it wont start, or wont spin, or it locks and you cant get it opened. I contacted Whirlpool and their answer to the problem was they would be glad to set up an appointment to send out one of their techs (at my expense). I have hired another tech and being told that the mother board once again needs to be replaced. I am so disappointed with Whirlpool and their service. I dont understand why they won’t stand behind their products. I will (when able) purchase another washer, but it most definitely will NOT be Whirlpool. Anyone else having issues with the same model? Would like to hear.

I bought a Whirlpool dishwasher. It has a plastic removable cap to pour in the liquid for their Rinse Aid drying. It is something like a bottle cap, a 25 cent part. I lost it. I called up, they wanted 12 dollars for the part and 9 dollars for shipping. They refused to just put it in an envelope and put a 30 cent stamp on it.

This is the worst washing machine we have ever owned. We purchased the Whirlpool Cabrio washer and dryer set at Lowe’s in Loganville, GA on 04/11/2010. Today is 02/22/2013 and the transmission is shot in the washer. It began making an extremely loud and terrible noise during the rinse and spin cycle. We called a local and trusted appliance repairman, and after his diagnosis including estimate to repair the washer, it totaled over $525.00. This is a terrible washer. I will never ever buy a Whirlpool appliance again. Oh, forgot to mention we have purchased four (4) major appliances from Lowes over the past 2 1/2 years in addition to purchases for our plumbing business and wont do it again! Also, Whirlpool couldn’t care less and there is just one complaint after another for the exact same problem online.

Our Whirlpool Dishwasher model WDT710PAYW is less than 2 years old and is rusting on the outside of the door where the steam vent is. Apparently the hole that was made in the door for the vent was not sealed, now the paint is blistering up due to the rust. Will not purchase another Whirlpool.

We purchased a top of the line (we thought) Whirlpool stainless dishwasher 15 months ago from HHGregg. All was fine until 2 weeks ago - it produced a burning smell and was making a funny noise. We had it looked out. The motor is burning out. I called Whirlpool and explained the issue. There is nothing they can do. It is over 12 months. Really? They cant stand behind their product? I understand if it was a small part or such but an entire motor burning out in just over a year? I know that not all products can be perfect, some times mistakes slip through the line. I guess it was silly of me to expect a company in todays age to stand behind their name and product. Obviously, with this company, it is buyer beware.

We bought a small refrigerator/freezer Model WRT112CZJZ for a guest house. When not in use it was turned off at the unit control panel with the doors left open. There was a power failure and when the power was restored the refrigerator turned itself back on. Needless to say it must have been running for 2 weeks with the doors open and the condensation filled the holding tank and then proceeded to overflow on the wood floor. The floor was ruined. There was no indication in the manual to warn of the unit restarting when power is restored so it must be unplugged or the circuit breaker turned off to avoid a similar problem.

Six months after purchasing my Whirlpool Washer model number WTW5000DW0 I would hear what sounded like rocks in the bottom of spin drum during spin cycles. Then noticed it was taking longer for clothes to wash and sometimes the water did not completely drain. Called for Service under LOWES warranty (the worst people to deal with). Tech comes removes a penny and dime and tells me that is the problem. Leaves. 45 minutes after he leaves there is the noise again. Call and set up for this Service Company to come back. Even though they went out of business prior to the appointment Lowes Service would not listen to me and insisted I stay home ALL DAY for someone who did not show up. Repeated calls to the Service Company resulted in nothing - phone disconnected.So finally after much frustration I am given new appointment with new Service Company - PARRISH. Tech comes in here five minutes and wants to know the sound, I explain. He checks out the unit and tells me it is a major problem and the part and labor will be costly. Best if they just replace the machine. His added comment - I see a lot of this. So if this machine is such a problem why was it not recalled? I am getting a replacement as I have warranty and machine was not a year old when problem started. Lowes Service Contract is another problem but I will deal with that later.

I bought a Whirlpool Partner II 5 and a half years ago. It was always noisy and took very long to run a cycle. It started to malfunction after 2 years. We bought a new computer for it and a new control panel for the touch keys. It still kept not running a cycle fully. We found a YOUTUBE video that showed how to reset the model by pressing a combination of Normal and Heated Dry and that seemed to fix it for 2 years.It has stopped working again. Now it seems that the heating element is out. It doesnt clean at all, a scum film has covered the inside of the dishwasher and even mold spots are appearing. Ive had to wait extremely long times on hold to talk with an agent. My option is to hire a repair tech to come out and repair it and I pay for the parts. Seems like a bad deal since Ive already spent over a hundred on repairing it and a lot of hours. I will never buy a Whirlpool brand appliance again.

I bought a Whirlpool built washing machine on Jan. 8, 14. It stopped working on Aug. 9, 14. It is now Sept. 2, 14 and I am still waiting for it to be repaired. I am age 75 and it is difficult to load and unload clothes to take them to the laundry. The repairman order a part Aug. 26. Pony Express has not deliver the part at this time.

Because the lid was not thoroughly covered, painted and sealed, it began to rust within first year. When I contacted Whirlpool about this - they were not only rude, but will not support quality issues with their products. They basically said they did not care and even acted like a consumer should expect such things! Actually said because its subjected to high moisture levels. WRONG, I do NOT just expect rust. It only formed due to poor quality paint job and was not cured correctly. My Kenmore washer and dryer both, were 25 years old and had zero rust and still functioned when I replaced them with these Whirlpool. Its frustrating that there are no quality, American made products anymore.

We purchased a Whirlpool upright frost-less freezer (model # EVL201NXRQ05) in October of 2008. So, you see, it is not even four years old. A few months ago I noticed that some things in the freezer were very soft. I looked at the back of the freezer and there was some ice buildup around the area where the coils are located. I took everything out of the freezer and removed the panel over the coils. There was major ice buildup on the coils. I completely defrosted it and dried it out. I restarted it and it seemed to be working okay. But a few days ago, when I got something from the top shelf of the freezer, it was not even frozen. So, here I go again. I removed everything from the freezer and have defrosted it again. However, this time, as soon as I turned it back on, the ice started building up on the coils immediately. It is impossible to contact anyone at Whirlpool that gives a crap. We have also been having problems with our Whirlpool Gold refrigerator. We have spent over $250 on it and it still is not working properly. I would love to just throw them in a ravine, but we have spent a lot of money on these appliances. We thought that Whirlpool was supposed to be number one in appliances. What a huge mistake we have made and it is costing us dearly.

We purchased our Whirlpool Cabrio platinum washer about 3 years ago. I am completely frustrated with it. When it is on spin cycle, it sounds like a freight train going through my house. During the rest of the washing... it squeaks. And right now this is the 5th attempt to wash the same load of laundry. Because it keeps getting unlevel and it will not continue after I move the clothes around to get it level. So I have to start all over. There is not a spin cycle option that is available by itself. Every time I have to choose the rinse/drain/spin option. Obviously it is not under warranty anymore! Only a one year warranty... really pathetic! And when we called they offered us a little discount to buy another one. No thank you!!! Wont ever buy Whirlpool again.

My wife and I made the unfortunate mistake of purchasing the Whirlpool Gold Series, model #WRF989SDAM00 refrigerator two years ago...yes TWO YEARS AGO! We have experienced numerous issues with the appliance but our latest (no cold air in both the fridge and freezer) prompted a call to a service center. The serviceman that showed up knew immediately what the issue was, our compressor and evaporator had malfunctioned and according to him, We have seen the same problem in a number of these models and that Whirlpool has since redesigned the casing to prevent this issue in new models. What about those of us who purchased the previous model?! Now shame on us I guess for not purchasing the extended warranty...I suppose I just took it for granted that in todays competitive manufacturing world Whirlpool would be committed to building a quality product! Because of this I was offered two options from Whirlpool. #1 - pay for the parts yourself...over $800 or #2 - purchase their 1 year warranty program @ $350/year, this warranty will cover all parts and labor for an entire year. Based on my experiences though, I will need to purchase a 1 year warranty @ $350/year for the life of this lemon, potentially costing me $5500 over a 10 year period. I ultimately took option 3...tossed the piece of junk and bought a new fridge from their competition. Dont be fooled by the attractive design and appearance, the Whirlpool Gold Series refrigerator is a money pit waiting to happen!

We bought a Whirlpool front load about six years ago. We have had nothing but trouble with since we have owned it. First, the sensors went out on it. We had to pay over $300 to have that fixed. Then, it wouldnt run right. We had to pay another charge for that. Now they tell me the water valve is bad on it. If I had known at the time the problems I was going to experience with this washer, I would never have bought it. I fell for the price. We paid for it. We should be getting better service from it than we are. I could have bought 6 regular washers for what I paid for this one that doesnt perform like it should.

My landlord purchased a new Amana washer (NTW4605EW0) Labor Day weekend 2015. It started having issues in the spring, so we went through the process of utilizing the manufacturers warranty. Apparently, Amana, part of Whirlpool, requires 5 attempts at repairing the machines before replacing. Okay, so starting in June 2016, we arranged service appointments 5 times and replaced 1 part, then another, 4 times. Clearly, that part is defunct. Right? Fast forward to September and then into October. Get a new washer, and not the one I preferred. We got the Whirlpool WTW4816FW1. Before the installers leave, we are having the SAME issue. Stops midcycle, doesnt finish cycle, sometimes stops while filling, or while full, or kid wash, or mid drain... But now with the new washer, the drain and spin cycle thinks it should FILL instead of drain... and Whirlpool said they would get someone out the next day, a promise they cannot keep because they dont supply the repair guy, they source with local companies. So, the company ordered 3 parts... That could be the problem. And 4 days later, 2 parts are on freaking BACK ORDER. Parts arrive. All new parts replaced. Machine still doesnt work. Outlet tested by us and them and it is fine. The techs think there is some kind of RF interference. Turn off sensor light, which is on the same wall, unplug power to wifi router (which outdates the washer). Still, doesnt work.I have spent half my week, every week, since June, restarting my washer, unplugging the damn thing, waiting, and waiting, trying again and again and again to wash 2 loads of laundry a week... Literally takes a week until the damn thing does its job. Whirlpool is sent us a replacement washer. Can you guess what happened the first time we started it? SAME ISSUE. Cycle will not complete. Sometimes it dies before it even fills. Sometimes it dies while filling. Sometimes, it will fill and fill and drain and fill and fill and drain and... never stop filling. Or, the fun one, the drain and spin cycle thinks it is suppose to fill. Continuously. And then, suddenly, after unplugging it for 1 hr, or 24, or 72 hrs, it will work fine for 1-7 cycles. Nothing is consistent except that it doesnt work consistently. HAS ANYONE HAD THIS MUCH TROUBLE???

Just bought 4 new whirlpool washers and dryers for my new four plex I am building for clients. Two of them leaked violently along the wall and downstairs. Did I see they were BRAND NEW. Total garbage. Now I have to pay for servicemen to come and fix it. NICE AND THANK YOU for your poor quality commitment. Now my clients are pissed off because they cant move in because whirlpool makes garbage material. So the extra cost it has cost me is totally unthinkable. Whirlpool, ask me if will buy from you again. Thanks for ruining everything due to your inconsiderate quality levels.

Out of warranty, slab of ice forms every few weeks in bottom of freezer. I have to take a butter knife and chisel it out to prevent having to defrost the entire freezer. This is clearly not isolated as after reading online and this forum, it is a manufacturing DEFECT that should be fixed at no charge to the consumer. It was delivered and installed by the retailer that sold the brand - however it sounds that Whirlpool would rather lose customers to other brands - trust me I just bought a stove and bet your sweet behind it was NOT a Whirlpool. Neither will the replacement for this piece of crap be once I can scrounge up the money.

Two Whirlpool washers in six years that the barren in back of tub goes out. When the first one went out in the same month the warranty expired, I was told by a repair man that it was not worth repairing because of the cost. I purchased a brand new Whirlpool and only months later, the same parts are broken on this new front loader. How cheap is the Whirlpool app. made? Whirlpool wants to only send me a tech. to fix washer instead of replacing unit altogether. After all, the unit is only a few months old. I cannot believe I have to deal with this again.

I purchased a Whirlpool Cabrio just over a year ago. The washing machine does not clean clothes! While under warranty, a service tech came out to look at it. After hearing the problem, he replied that it was a common complaint and that he could not fix the machine because the problem was that it is so poorly made that it simply does not work. His recommendation was to come to terms with the loss of a thousand dollars as Whirlpool would not rectify the problem.Whirlpool really showed their true colors when they refused to cover the repair tech visit. Whirlpool supervisor Kitty explained to me that customer advice was not covered under warranty and that we would have to pay the bill. Highlights of her argument were that we should just rinse the clothes multiple times and they would eventually get clean. She also mentioned that if the machine really did not work as described, we should have complained sooner even though it was still under the one-year warranty. Whirlpool will sell you junk backed with horrible customer service. Beware!

We purchased an Estate Washer for my 89-year-old mother in 2008. The paint has been peeling down to bare metal on the left top quarter from the corner down to the lid hinge for the past 2 years. I contacted customer service and was given probable causes, one of which was the washer might have gotten dusty! He said that could cause chipping. I reminded him the problem is peeling chunks, no chips, layers of paint. The warranty expired of course. The solution he offered was for me to buy paint from Whirlpool or Lowe’s, and paint it. I have had a Kenmore washer for 24 years. The paint is perfect, and it still runs great. I would never buy another Whirlpool product. The quality is atrocious.

Ordered this two days after my son came home from college. He had to be out of his apartment July 31 2016 and brought 4 years worth of laundry with him. Monday my machine breaks, Tuesday I order this thing from Lowes Arrives at 2:30 on Thursday and as it is being installed I ask why the water fill is so slow. It is trickling out like a childs toy. Delivery man tells me the water is completely turned on. He hears this remark a lot from people who buy this model. I put in my first load of laundry, a small load of about 6 things that I am washing for my mother who is in a nursing home. They have that nursing home smell. I push pause as the machine is cleaning to unlock the lid and peek inside. Oh my God the clothes are sitting on top of each other not even covered in water. I then shut the lid and listen to the tiny slush of the machine agitating. At the end of the cycle they smell exactly the same. Dirty.I had read to use the deep fill so I rewash them on deep fill. Look inside halfway through and what do I see? Wet clothes piled on top of each other, still not floating in water. How are these clothes getting clean when they are in a wet pile on the bottom of the machine? I take them out. Still not clean. Not smelling quite as bad, but not smelling like soap. I then washed sheets, a blanket, and some clothing of my sons. Nothing smelled particularly dirty but NOTHING smelled like soap. The quilt was covered in hairs (my son and roommates had a dog) and soap residue. I had read this in reviews online also. I am wasting time since each load takes from 50 to 130 minutes (yes). I am wasting soap, oh but I am saving water - not really.Well Lowes has a 30 day return policy so I went down there and am expecting a GE machine with an agitator tomorrow, Saturday! Cant wait. The only one saving money are these manufacturers They no longer are spending cash on producing the agitator out of plastic, attaching it with nuts and bolts, or using gaskets between the parts. DO NOT BUY THIS PIECE OF JUNK, do not even look at it. I question all the HE machines at this point. You need to use HE soap cause you cant wash away suds in a machine with no water. What a con - the whole thing is.

Whirlpool W8RXEGMWQ01 leaks - It looks like the seal is not tight around the freezer box. They blamed it on my floor but I think its because the door sags. The door needs to be lifted about 1/2 to fit snugly into the freezer box opening. They came out three times but couldnt fix it, then they said it was my fault. Then I finally gave up.

Whirlpool White Ice gas range with aqualift technology. Whirlpool uses a self-cleaning technology called AquaLift to clean the oven. It does not work. It does not clean the oven no matter how many times you run the cycle. I have contacted Whirlpool 3 times and they did respond. They first suggested buying their oven cleaner. I purchased the oven cleaner and it did not work! They then said that aqualift will only clean the bottom of the oven (it does not). Who buys a brand new oven that does not have a self-cleaning feature? I read reviews online prior to buying this oven and unfortunately for me, there were no bad reviews. However, I just checked again and there are numerous reviews stating that aqualift technology did not work for them either. This oven bakes but it does not clean and Whirlpool will tell you not to use oven cleaners in your gas oven because they will damage the surface of the oven. I currently have a very dirty oven and no effective way to clean it! Do not buy this oven if you want a self-cleaning oven. This oven should be recalled and money refunded. I would never knowingly buy an oven that does not self-clean. This Whirlpool with Aqualift is not effective and the company had to test this before it was marketed. I do not know which brands to recommend at this point as I am stuck with a Whirlpool gas oven that does not self-clean. The oven is only 1.5 years old so I will be stuck with this oven for a few years. Do extensive research before you buy any appliance.

I am very happy with this dishwasher. It is not a high end, rather middle of the road, but is very quiet, does a great job of cleaning my dishes and pots and pans.

7 months ago we had a Whirlpool dishwasher installed into our home. While away on vacation the piece inside malfunctioned and caused major damage as water filled the home. Whirlpool claims, that because it’s a part that they contract out to another company, they “Whirlpool” are not responsible! If you purchase a product from Whirlpool and they put their name on that product, then Whirlpool should stand by its product. Well... beware, you’re not going to compensate from Whirlpool! We urge you, make sure of whom the parts of the product your buying from belong to, before you buy it FIRST! Never again!

I purchased a #Whirlpool; 4.3 cu. ft. Mini Refrigerator Stainless Steel BC-127B from @Target. There was a delay putting it into service (6 mos), so the Target store warranty was expired. The unit remained in its factory shipped packaging until put in service, so nothing out of the ordinary there. After barely two weeks of use, the compressor died. I followed all instructions (including waiting 8-10 weeks) from Whirlpool, but still have not received a refund or been given any information beyond we escalated it to our warranty team but havent heard back yet. The unit was a poorly made piece of junk in other respects as well. There are dozens of complaints about precisely this - defective units - on any site. Do not be fooled by the dishonest way that #Targets website lists reviews. Dig deeper.

I bought this stove 4 years ago from Lowes. I have had nothing but problems ever since. My family is now afraid to use the stove and Whirlpool refuses to stand behind their product. The last straw was a bill for a service call that took 6 months to complete without correcting the problem. Whirlpool sent me a bill for $100 to pay for the privileged. When I complained, WP said if I paid the invoice, they would give me a deal towards a new stove. Meanwhile, the old stove does not work and we are afraid to use it, given our experience with its reliability and safety. I plan to return it to Lowes and buy anything but a Whirlpool product. Beware of Whirlpool Maytag anything!! The customer service is shameful!!

The front of the stove gets so hot you can burn yourself and I feel it is not safe around small children or grandchildren, and it should addressed to fix the problem not just cover it up. Please give me the info to fix the problem before I have to sue over my grandchildren and great children getting burned.

1st item - ice pooling at bottom of freezer, now repaired at a cost of $100. 2nd item - 1 day later fridge/freezer keeps shutting off and on irregularly. Cant contact anyone one from Whirlpool on a weekend and Trail Appliances doesnt have anyone available to come and look at it and if they did it would cost us another $100+ with no guarantee and we were told by Trail the Whirlpool will not touch it if someone else does. From what I have read seems we now a victim of Whirlpool. P.s. for those who dont know yet Whirlpool not only now owns Bastemp, they also are the makers of Kenmore and those fridges have experience the same ice issues.

I purchased a new Whirlpool 3.6-cu ft Top-Load Washer (White-On-White) Model #: WTW4800BQ from Lowes on 11/1/14, which was only 3 ½ years ago. The washer began making noise during the spin cycle so we called for service. The technician claimed that the bearing pack needed to be replaced and the repair would cost $400. This amount is $20 higher than the amount I paid to purchase the washer. Because the warranty is only one year, I contacted Whirlpool today and spoke with a representative. The representative said they could repair it under the warranty. When I asked how to proceed, she then asked me if I had an extended warranty. When I replied that if I had an extended warranty, I would be using it. She declined any assistance. I now have to purchase a new washer after only 3 and ½ years. I own 10 rentals. I promise that none of them will ever include a Whirpool product again.

We purchased our Whirlpool dishwasher/Model no. WDT780SAEM in July 2016 and it was installed on August 3, 2016. Right away we noticed 2 problems. The top tray squeaks very loudly when being pulled out for loading and unloading. The usual temporary fix for this would be using a product like WD-40. Of course as soon as you run the dishwasher all of the product is washed away. This was our first complaint about this dishwasher. The more important problem was the white cloudy residue being left on all of our clear plastic cups and glasses. Weve always had hard water but our previous dishwashers were able to remove the residue if we used the high-temperature wash. After looking at all of the manuals and user guides that are included with the purchase we read that we should be using a rinse agent and a product such as Lemi Shine to deal with hard water deposits. We tried these items and nothing worked.Using the All Fresh tabs didnt help and our filter was clear and clean. So we made an appointment to have the Whirlpool factory serviceman come out to look into our problems. First of all the customer service representative I spoke with was rude and impatient. She kept cutting me off and asking me about hard water and suggesting that I use all of the products mentioned above before finding out that I already had used them to no avail. Because we had the dishwasher for just over 30 days I asked her about the Clean and Quiet Guarantee that I found out about by going to Whirlpools site. Her exact words were The clean and quiet what?? So I didnt have much hope for our service appointment. Our serviceman was asking all of the same questions about hard water and if we had tried all of the products I mentioned above.After his visit we found out and now (too late) know that because our new dishwasher does not have a heat booster or the ability to get the water temperature high enough to remove the hard water residue theres nothing Whirlpool will do for us. This is the case with all newer technology dishwashers UNLESS you purchase one with a heat booster. I sure wish this wouldve been made clear to us, the consumer before making our purchase. If we had known beforehand that new dishwashers no longer get the water up to 140 degrees which is what would be needed to remove the residue, we wouldve made sure our model included a heat booster. Now were stuck handwashing our plastic items if we want clear dishes. Its not the end of the world but its not good customer service or honest to the consumer in any way, shape or form.

I purchased a fridge from them a little over a year ago. First and LAST EVER. The freezer door started to sag and when I called them I was told my warranty expired a month ago. Had a Whirlpool service person look at it and told me that the cost is $110 plus $45. I said that is fine. They scheduled another appointment but I received a call 12 minutes before the time expired (as you know they say in the afternoon and no exact time and they said between 2 and 4:30) and the guy asked me what is wrong with the fridge. I told him that someone took a look at it a week prior but I had to go through the whole thing. Then he said that they dont have the part and I have to wait for a week. This was a Saturday before Xmas and waited all afternoon to be told that was very upsetting. Any how I called customer service and spoke with a Michelle. She said she is going to try and find out if she can waive the additional service fee, arrange the time and will comp the parts (around $15). After 45 minutes on the phone I had to jump off for a business call so Michelle said she will email me and I gave her my email.Few hours passed and no email. When I called back the idiot that answered the phone kept saying that the warranty is out and I need to call another number so I asked for a supervisor. I was on hold for 11 minutes then I was hung up on. I called again and asked for a supervisor. Spoke with Benjamin (Opt# **), he said that Michelle notes did not state anything about help in possibly waiving anything and that I refused the parts. I was furious. What a LIE. Long story short he said they cant waive anything and I should call the scheduling number for any help. I asked to speak to Michelle and guess what the answer was... SHE IS BUSY. What the hell. The service is well below zero as well as the quality of the product. I am going to send a letter to the office of President (Jeff Fettig) Whirlpool Corp. 2000 North M-63, Benton Harbor, Michigan 49022-2692. It is so sad when corporation are so big that little people who buy their products dont mean much to them.

Whirlpool serviceman came out to see why our brand new dishwasher didnt dry the dishes and left pools of water on glass bottoms. Repairman said all the new dishwashers are like this. The heating elements do not heat hot enough so that the machine gets a higher efficiency rating. He said the solution is to use the dishwasher during the day and at the end of the cycle, open the door so the dishes air dry. My previous 24 year old GE dishwasher did a great job of drying the dishes even when we didnt use the heated dry cycle! The only reason we had to buy a new dishwasher is because we bought a new house. I am very disgusted with the Whirlpool dishwasher. Might as well do dishes by hand.

We purchased a Whirlpool Cabrio washer and dryer set in 2013. In 11 months we have made at least 6 calls concerning the same issues machine leaving white residue on clothes. It has been one thing after another. Today the manager told me that my warranty only covered parts and not a replacement machine. I am washing my clothes two or three times to get them so we can wear them. First this is not saving water, energy, time and most of all CLOTHES. We are wearing our clothes out washing them. This is unacceptable. With this many complaints, the company has to know they have a machine with issues. I will never purchase Whirlpool again. I think we should all band together and file an action against Whirlpool. These machine cost too much money to be crappy.

Whirlpool realized in 2002 that this was a defective part. In 2005, they recalled the product. I purchased the Hot Water Heater (Model # BFG1F4034T3NOV) in 2006. Being this product was recalled in 2005, why was it still being sold at Lowes and other stores? Why wasnt it pulled from the shelves? Why werent the parts replaced before being sold? The hot water heater stopped producing hot water. I contacted Whirlpool and they said the gas control valve had to be replaced; they gave me a part # and an authorization # and told me I could pick it up at Lowes. I asked about installation, because it is still under warranty. They said they dont service this. I picked up the part and tried to find a plumber to do the work and they said it was too small a job. I had to impose on friends to help me; one is a volunteer fireman. He came out and put on the new part and in doing so, another piece broke. We called Whirlpool and they said they had to replace the manifold door assembly. They overnighted the part. Again, I asked about them servicing this hot water heater and I told them I am a single parent and cant do this work. They said they dont service this item. I then had a handyman come out to try to fix it and he wasnt able to get it to work and now I smelled gas (it cost me $198). I had to call the gas company and they came and said there was a leak and turned it off and gave me a violation. I called the company I have an HVAC contract with and they added the hot water heater to that contract and it cost me $120 more for a year. They finally got it working, I was without hot water for a week. I do not recommend anyone buy products from this company. They are horrible to do business with and their service is awful (the service they dont offer).

My three month old Whirlpool electric range caught on fire last night. The wiring that connects to the electrical cord to the stove shorted and melted. Thank God we were up and smelled it and quickly pulled the stove out and unplugged it. Had the fire dept out this morning and they verified that it was the stove and not house wiring. Now, I am without a stove, out of my money and waiting on the mercy of Whirlpool to take care of this situation. I do not want this stove in my house so I wont accept repair. Not sure I want another Whirlpool either. If this had happened during our sleep time, the whole house could have burned down. So upset and inconvenienced.

I purchased this machine in April and already, the right leg is rusted and the under seam of machine is rusted. I have throw rug under it and where the leg is, there is rust on the rug. I called service from Whirlpool and 2 servicemen came out. The first one told me I was loading it wrong and the water was splashing over the inside tub to rust the leg and I asked, So why is the seam under the machine rusted? No answer. The second one came out and told me he could not find anything wrong with the machine and doesnt know why it is rusting, but he never gave me a paper to sign off on. He also said that maybe it was rusted when it was delivered. Not!!! Then I call P.C. Richard in Watchung, NJ where I bought the machine at and told them about the problem. They sent a serviceman out and he said that the bleach condensation is causing the rust, its known fact that this machine has this problem. He said that the water does not run through the dispenser but there is a model that does. I want a credit on this machine and get the upgraded one. It states on the machine that I can use bleach but it doesnt say it will cause rusting. I want you to tell me how a 9-month-old machine is rusted on one leg and the seam underneath is also rusted!!!! I had a machine for 10 years and it wasnt rusted. I am very unhappy with this product and with the customer service of Whirlpool. This is my first Whirlpool washer and I would not recommend this washer to anyone. I paid $600.00 for this washer and it should not be rusting.

We own this range and in 6 years its 4 main boards and 3 touch pads were replaced. The electronics suck big time. We have nothing but trouble with this range from day one and out-of-pocket cost for service calls that were recommended by whirlpool. They were absolutely no help. Expensive piece of crap! I will recommend NOT TO BUY ANY WHIRLPOOL PRODUCTS. The electronics suck big time! I kicked the Jenn Air out the door and to the land fill. I bought a new range, but not whirlpool product, with dials only, no electronics!

Weve had this microwave (WMH31017AW-2) for 2 1/2 yrs and the door is falling apart. It started with one crack and now the middle glass of the door is falling out! I took the door off so the the glass wouldnt fall on the stove and the plastic around the door literally crumbled apart. So disappointed since that was the same reason we took the other one back that was in this house when we bought it. The microwave is now discontinued and when I did find a door online it costs as much as the microwave! Whirlpool doesnt distribute the dependable products that were, back in the day, associated with the name WHIRLPOOL. Shame on the greedy people who have taken over and cut back on quality material and labor to put an extra penny in their pocket!

We purchased a Whirlpool French Door Bottom Mount Refrigerator on July 14, 2014. Price $2,139.99. We chose Whirlpool because they have always manufactured and stood behind their products. Hah! We will NEVER purchase another Whirlpool product or even a product made by Whirlpool. The refrigerator quit cooling over a week ago. After calling Whirlpool service center they set up an appointment for a service call. The repairman came out said it was the refrigerator fan motor and another piece. He tried to order both but was told the parts would have to come from Lakeland, Florida and it would take about 5 days or so to receive them. We called Whirlpool. After being on the phone forever they finally said they would overnight the part to our home address then we should call the repairman to make a return visit. We received the parts last Thursday, called the repairman and he couldnt make it out here until today. When he got here and started to replace the part he discovered Whirlpool had sent the wrong fan motor. He called Whirlpool and they said the part was on back order and it would be shipped in 5 plus days or so. Both my husband and I talked with Whirlpool and the only thing they were willing to do is if they find the part they will ship it overnight then we would have to call the repairman and schedule another service call. They did say if we found the part they would reimburse us for the part. They wouldnt talk with us about replacing the fridge, etc. I will be out of a refrigerator for what looks like 2 plus weeks and this is not acceptable service from a company like Whirlpool. Pretty much everything in our fridge has gone bad. Whirlpool is not even willing to compensate us for our loss of food. They said all they could was offer us a 6 month extended warranty. We are completely unhappy with their service or rather lack thereof.

I bought a new Whirlpool refrigerator at Home Depot for about $700. Six months later, suddenly, it starts making an intermittent but constant loud grinding noise and then the squeaking started. I called Home Depot first because I bought the protection plan. They referred me to Whirlpool who said the protection plan doesn’t kick in until another year after the warranty ends. It makes these noises whenever it runs, which seems to be more often (that it is running). Whirlpool may still charge $120 just for someone to come look at it even though it is under warranty. I asked another repair place and they said it might void my warranty for them to look at it instead. Whirlpool said it wouldn’t void the warranty but they would only work on it after the first repair person was finished. I’m waiting for the repair guy to come and see why it is making these loud noises. Another person with more knowledge of fridges than I have listened to the noises and said it sounds like friction in a motor. I read a review of the fridge that said the reviewer had problems after only 6 months and I thought that must be a fluke. Apparently not.

I am posting to help anyone else avoid the purchase of this machine! The lid has cracked and now warped into a position where it wont stay down. Obviously a washer will not work without being in the locked position, so we have to put several heavy things on top of it just to run a load of laundry. This is not what we expect out of a washer that we paid $900 for only two years ago!!!! We contacted Whirlpool and they offered to fix it for $350. REALLY??? I SHOULD NOT have to pour money into a washer this expensive after two years!!!! I am so disappointed in Whirlpool, this was the entire reason we purchased Whirlpool products, to avoid stress of broken appliances. We wanted reliability for our busy family and instead we bought into more stress.

I purchased the Whirlpool washer with the expectation of having at least clean clothes. In fairness, I do wash some pet items but they are done separately. My clothes at time come out dry in spots because theyve not been touched with water. Forget the balancing issue. What I will have to do is wash, rinse, and repeat. This will be my life until I can get a new washer. Never again Whirlpool.

I have had to replace the thermostat 3 times. Worst fridge I have ever owned. Lost lots of food and time and money that I will never get back. I will never ever buy another Whirlpool product again. Aint got time for that.

Whirlpool refrigerator Model WRT771RWYW01 - Having been pleased with my old Whirlpool, I made the mistake of buying one now made outside the US. First, we had to have the cold cut tray replaced, which was covered in our warranty and not a problem. Then, we complained because you can only put things on the front half of the shelves or they freeze solid. We were told, This is the way they are made, dont put things in the back.” So, I have to put my eggs in sideways so the back ones dont freeze and cant use the back portion of the refrigerator shelves. I paid a lot and I am angry. Lets go back to the US people where things were made right.

It is in the mid-range of cost and functions. For a mid-range dishwasher, it has many options, sometimes too many. It does not have rinse and hold. I think its cycles run too long; not always energy efficient (i.e. the simplest one uses the most energy).

I paid over $1,000.00 for a washer based upon previous experience with Whirlpool appliances. I am single, over 65, and use this machine infrequently, as compared to when I had children. The only thing Whirlpool is offering is another of their machines at a discounted price. I value principles more than dollars. I refuse to give them another $600+ as a reward for making junk which apparently should have been recalled. The part I need is not available any place Ive found online. And it completely controls the power to the machine. You cannot open the door, you cannot turn it on. I had two service calls to discover this part is not available.

First, I was put on hold by the first female for 44 minutes, and then a second woman finally answered, and said she didnt know why she would send me to her, because she was in the sales department, and she put me on hold for another 25 minutes. I finally had to go, because I had an appointment. When I got home, I called back, and got a man by the name of John, and at least he recommended he could schedule a repairman. The problem I told him is, the inside wall of my refrigerator has 2 cracks on the side, and a crack on the back wall. I dont want a repairman to come, just to tell me he cant put 2 new walls inside of my refrigerator. I could not find an email, so I could email Whirlpool about this problem, and definitely, they were of no help. I bought the refrigerator at Lowes late 2003. I have never, in my life, seen the inside walls of a fridge do this. I spent a lot of money for this, for it to crack on the inside walls. It does not seem like something is right with this.

We bought a new refrigerator when we bought our house in Dec. 2008. On the third of July 2015 my Whirlpool Gold stopped being cold. In fact it was a bit warm. Had a repairman out here today. Warranty expired and the compressor has failed. Wow! Im not happy.

I regret buying this washer. No complaint about the dryer but this washer has been the worst investment I have ever made. My clothes gets tangled up - seems like theyre not as clean as with my old washer which by the way I still have. I wanted a bigger set because I hated spending days off doing laundry but I spend as much time rewashing again and getting clothes untangled.

We purchased an over-the-stove Whirlpool microwave in January 2011, when we remodeled our kitchen. In May 2014 after a loud pop, the microwave stopped working. This was Model # GMH6185XVS-1. Of course, the warranty is no longer in effect. I feel a high-end appliance that cost $500 should last longer than 3 years. I will not purchase another Whirlpool product.

Whirlpool Cabrio - We bought this washer in June 2013. The gearbox just went out (17 Nov 2015). Terrible product. We had to buy a new washer; and it wasnt a Whirlpool.

We have been very happy with our appliances that now over 11 years old and doing well. We love our gas range top. They gave greater and new models so we love Whirlpool and GE. We always get great deals at Home Depot.

I purchased a Whirlpool washing machine (model: AW01D8810 S silver color) and a Whirlpool refrigerator (model: WBM329 TI) together from United Arab Emirates for Dhs 1999/- & Dhs 1199 /- respectively on 28 Jan. 2011. I sent this machine to my hometown (India) in the same packing and I used the washing machine only for three months and found a complaint. I informed this to service center in Trivandrum, Kerala. Their team came to my home and told me that warranty cannot be given as I purchased machine overseas. They added that the PCB for the machine is having complaint and they dont have stock in India. Also, the machine is no longer available in the factory. The Whirlpool company completely stopped manufacturing the abovementioned model. Again, I came to UAE and contacted GEC group of companies for the PCB part. I got a quotation for PCB Dhs 425/- but the items is ex-stock with them. The machine cost only Dhs 1999/- and if I spend Dh425/- only for PCB, and the machine is with me for the parts since one and half years. I dont know what to do. If I spend another Dhs 600 + this PCB cost then Id rather go for another new branded washing machine. The model of machine is AWO1D8810S and serial no. is 12 nc 859247463000 003. Please advise what to do or if I can find the PCB in Kerala. What will be the cost? I am ready to pay the money for PCB but not for the above rates. Please advise, sir.

Spent the extra money to have a beautiful, slide-in oven. The AquaLift technology just seemed like another plus. After the turkey cooked, just seemed like another oven to clean. The AQUALIFT does not work, except for the bottom of the oven!! A fresh oven cleaner? Only available only. Get this beautiful range, not AQUALIFT TECHNOLOGY. CLEANING with it.

I have had my Whirlpool electric oven for so many years that I don’t even remember when I purchased it. I also have a Whirlpool stove top & the same with it. Zero trouble for many years. I highly recommend Whirlpool range tops & ovens.

WHIRLPOOL MICROWAVE HAS HAD MAGNETRON GO BAD 3 TIMES IN 1-1/2 YRS! I bought a Whirlpool Microwave Hood Combo Oct 2009. July 2010 the magnetron went in it! December 2010 the magnetron went in it AGAIN! This time we had to pay the labor to have it repaired because it was 2 months outside the warranty period. We did not want to pay because we knew having the same part go twice in one year that something is wrong with it. Whirlpool told us that if it happened a 3rd time that they would most likely replace the appliance for us. Well....July 2011 the magnetron went AGAIN for the 3rd time! Whirlpool told us to take it to a licensed shop to have it diagnosed to prove that it was the same part as the previous two times, fax paperwork from the prior two times, and have the shop call in the diagnosis of the 3rd time. We did all that, and they told us they wouldnt do ANYTHING for us because it was outside of the warranty period! Well they knew that when they told us we had an opportunity to get it replaced! THE SAME PART WENT BAD 3 TIMES IN A 1-1/2 YR PERIOD OF TIME. We trusted that the Whirlpool representatives were being honest with us during those phone conversations. Whirlpool can not explain why representatives would give us hope of a replacement (although each conversation is documented by their login and employee ID number). So not only did I buy a brand new MSRP $619 microwave, I paid to have it repaired the 2nd time, and to have it diagnosed the 3rd time, uninstalled and reinstalled the microwave each time, the inconvenience of not having use of the appliance during each occurance, and the unbearable suffering of calling in to customer service and repeating the story over and over to each representative. My house is brand new (we moved in to it November 2009); we bought ALL our appliances from Whirlpool. All I get for an answer now is sorry. That doesnt help me any financially having to repair and now replace an appliance that has been in use for only 1-1/2 yrs! I have seen $39 microwaves from WalMart last several years, so what is wrong with Whirlpools manufacturing?! Customer Service is unreliable, untrustworthy, non-sympathetic, and insanely frustrating! My question for Whirlpool is...why cant you make a product that lasts better (better quality=longer life=healthier environment and happier customers)? Why cant you stand behind your products better? Dont you care about the impact youre making on us emotionally, financially, and environmentally? The model # is GMH6185XVS0 Serial # is TRY3111264.

Im yet another angry customer who is dealing with a defective Whirlpool hot water heater purchased from Lowe’s, still under warranty, and it failed. The thermocouple appears to have failed and, amazingly, the part is nonstandard in that it screws in backwards compared to every other HW heater. Lowe’s doesnt carry the part even though they sold the HW heater. When I contacted Whirlpool, they agreed the part is under warranty and will send one, but I have to pay shipping for a minimum of $10 and a week to wait, plus having to get the part installed. Obviously, I am one of many who bought this defective appliance. Whirlpool used to be a good company, but Ill tell everyone to avoid them in the future. Meanwhile, I have no hot water and its freezing in Cincinnati.

I purchased this Whirlpool dishwasher from Sears on 3/25/2010. Then on 8/11/2012 the dishwasher completely failed to operate. I called for service and they checked it out and they found out that the control board had failed due to moisture getting into the electronic components. They replaced the control board & control panel and the dishwasher has worked until today (2/08/2014) - 17 months, and now exhibits the same problem. The original repair costs including labor was over $400. Not really acceptable and demonstrates very poor quality control and design @ Whirlpool. As of now, I am considering whether to purchase a new machine (obviously neither a Whirlpool or Sears product). As part of the original service the soap dispenser also failed and had to be replaced. I believe Whirlpool should be responsible for some of the repair costs.