I thank the folks at Whirlpool for building a washer (Cabrio tub bearing failure) that lasted 22 days just shy of four years, better than the Whirlpool Duet that lasted 14 months, tub bearing failure also. Now I have high confidence that Whirlpool pre-engineers failure into every washer they build.

I bought a washer from Lowe’s Home Improvement in September 2017, called a couple weeks after the purchase. They sent someone to repair machine. It is still not working. Called Lowe’s back. Was given an 800 number. Talked with someone at this number got nowhere. Was given another 800 number. I am waiting to find out what is going to be done. This is terrible customer service.

I called customer service line regarding my Cabrio Automatic Washer (Model No: WTW6600SW2; Serial No: CU2171019) purchased on 11/24/07, to report and ask for assistance with a chronic ongoing service problem. Several calls in the past and service visits (at my cost) did not rectify the problem. Although there are many similar complaints on this machine regarding the loud noise and resulting problems during the spin cycle that involve the tub and rods, the representative said So sorry or Too bad we cannot not help you.My machine now does not run and is less than 4 years old --just like every other report. I get an error message F which the representative alluded to something involving the electronics. Machines purchased in 2004 from Whirlpool have across-the-board similar problems that Whirlpool refuses to take ownership for. This machine is their top of the line model. I dont feel the financial burden of repair or purchase of a new machine should be on the shoulders of the consumer. We bought in good faith from Whirlpool and expect Whirlpool to live up to their responsibilities. Thank you for any help you can provide.Rae **

Quiet Partner II - Our dishwasher racks started to crack and rust very quickly, about two years after purchase. We repaired the racks and tines, but the rust got worse. We replaced our dishwasher today with another brand. Many of the tines on the drying rack had rusted and broken off. We have been told to only purchase Nylon racks. I hope this is good advice. I must admit I had no trouble with the machine as far as cleaning my dishes. I just felt the racks should last longer than two years. Cost to replace racks was about the same as replacing the whole machine.

Whirlpool Cabrio Top Load, Short Agitator to protect clothing, cost reasonable, on sale $800.00 both (Aug. 2013) - Sears credit no interest. Moved, and had to sell after a year, but I anticipated a long life r/t rating/reviews online. One Problem: no setting to soak clothing that may need it. I bought the largest Whirlpool Cabrio to make sure my Queen bedspread (heavy blanket type fur on one side) would fit. Because of the short agitator I could have bought the smaller one I discovered. I could fit 6 regular side and 4 beach heavy beach size towels in it easily, or two Queen quilts in at a time. I rarely needed an Xlg water setting. The dryer had a steam only setting but I never tried it because it was set up in the apartment when I arrived and the delivery people were not very bright. Put the Dryer farthest from the vent, washer farthest from faucets, and put hot and cold hoses on opposite spigots. I did not want to chance they set up the steam section wrong, as well. I moved across country 1 year later, but have trust the W/D would do well. My last Sears brand (made by Whirlpool) only had one minor problem (on warranty) and lasted a good 8-10 years before moving and selling them to another couple. They were still in wonderful working order (front loader).

For years, Whirlpool has had an outstanding reputation for quality, so I cannot understand why a refrigerator I have owned less than three years has to have all the shelves and bins replaced. Not the glass, just the plastic. They actually started breaking the first year. I have literally had to tape my shelves together. These are very expensive and yet they are very low quality and of course are not covered on the warranty.The plastic is not built to withstand the cold and/or weight of food products. They need to get rid of the plastic and replace it with metal. I dont want to replace them with the same low grade products. I own the model ED5JHEXTB00 serial # HRU4010107. Also, the ice maker has been replaced twice. What has happened to Whirlpool

We had the Whirlpool Cabrio Washer [WWT5640xw0] for approximately six months and it began to behave strangely, very much like the other complaints I have read on this site. It works poorly, does not clean the clothes, there is a smell that is coming from the machine and it makes loud, inappropriate noises. It stops spinning and washing in the middle of a cycle. Before I become aware of the issue, I would find loads of clothes sitting in the water and the machine indicated the cycle was completed.What a piece of junk! We cannot afford to go out and get another washer at this time and based on what everyone else is saying, the cost of repairs is very costly. I too called the company and was greeted with indifference. I too will not purchase another Whirlpool product and have spread the news to my friends about this worthless product and manufacturer! My message to this company: Whirlpool, the right thing to do is recall the machine and provide us with a voucher so we might go and purchase another machine from any manufacturer we wish. But we all know that will not happen as the company is clearly saying to its customer base, Our sales and profits are more important to us than you and your satisfaction!

This Whirlpool side by side 2 door Refrigerator/Freezer stopped working yesterday. It was manufactured in 04/2013, and I purchased it from Lowes on 5/26/2013. My invoice number is **. The last 2 refrigerators I have owned worked for well over 20 years each. Actually, longer, but I moved away from one of them. It is unbelievable to me that after 3 years, and 3 months, this unit has just stopped working. Of course, it is coming at a horrible time. In addition, it is summer time in Southern California, so the heat is high, and the desire for cold drinks and foods is also. It had been working well, until yesterday. Today, I am experiencing the foods become warmer and warmer. I will not be purchasing another Whirlpool Product of any kind.

We purchased a Whirlpool oven a year and a half ago. Today the interior glass exploded while cooking frozen French fries. Whirlpool customer service indicates that this is unusual. Whirlpool indicated that the only way they will repair it is if we pay $375. We declined to pay an additional cost for this product which failed to function safely. In a quick Google search, it appears that the oven glass fails more frequently than represented by Whirlpool. We are disappointed in this product and the companys customer support and lack willingness to correct a product safety issue.

I purchased this Whirlpool Cabrio washer three months ago from hhgregg. If I hit the lottery, the first thing Im going to do is take it to the dump and buy a new washer. There is no way to wash a load of towels in this machine. I started a load at 7:35 this morning and it is now 9:53 and Im still dealing with the drain and spin cycles. Over and over, I try to get it to spin out enough water that I can put the towels in the dryer. I should have suspected something when I saw that the washer even had a separate drain and spin cycle. It should have told me something. Its a piece of junk. Never again. Im back to Kenmore.

Help? WP Gold double convection wall ovens WOD93EC0AS rated very high by Consumer Reports installed end of February. Monday April 6, fan in top convection oven came on suddenly while oven not on. When I tried setting a baking temperature in top oven to see what was going on, message read This function is not available. After about 15 minutes the fan went off, and I could use the oven. Worked well Tuesday and Wednesday. Oven not used again this week, but this evening, Friday, same thing happened again. Process has been repeated several times with fewer times between fan turn on. Have turned off power to ovens until I can get a repairman. Has anyone else had this experience or know what the problem is. Have been reading about the problems with WP ovens. Wondering if I need in addition to Home Depot Warranty the one from Whirlpool as well. Had Bosch convection ovens for 12 years then self-cleaned and thermostats went out and cannot be replaced because parts no longer made or available through any supplier. Said I would not buy Bosch ovens again because the parts became unavailable even sooner. What a mistake. Apparently self-cleaning element blows a lot of ovens thermostats and/or circuit boards. Loved the ovens and had only one repair after the ovens were one or two years old. The Bosch dishwasher is same age and still working great and usually cant even tell it is on.

Our home came with an Asko dishwasher, theoretically a premium device though the experience was not the best. Anyways, had to replace it after a few years and decided to buy a Whirlpool under the assumption that if an Asko kind of sucks, being so expensive, it was not worth the money to spend big bucks on an expensive dishwasher. I could not have been more wrong! Bought a middle of the pack Whirlpool, I think we spend around $500. Complete junk. I had to use our Sears home warranty like 6 times. They replaced two times the computer board, all the sensors another couple of times, motor, you name it! Worst part is that all of the non essentials part that also broke off (wheels, and plastic pieces of the door) were not covered by Sears warranty so I had to end up using glue and all kind of contraptions to keep them together. Finally, when we decided to put our house in the market we replaced this junk with a Bosch. So far so good. Whirlpool actually never even washed properly, now with the Bosch we finally know what it means to have a dishwasher that really washes for real!

Whirlpool 27 cu.ft french door bottom mount WrF989SDAH White - We took delivery of this ice making fridge mid-September from Sears Canada. 3 weeks later we have ice at the ceiling/wall seam at the back inside the fridge. Water collects along the rubber seal of the freezer drawer which we have to mop up. We said we were not going to use the water/ice maker and its not even hooked up. Water comes down through the water dispenser onto the panel which we also mop up. Moisture in fridge. Temp settings are as factory specified. Whirlpool authorized tech guy gave us the inside info. Hes seen so many design problems with this model and what Whirlpool do is order the tech guys to say to customers we can order the parts and fix it. Whirlpool keep discovering and modifying the problems but you are not allowed a refund off the bat because the tech guys authorized & sent out by Whirlpool are not allowed to give a report to the retailer or say its design defective. So the customer has shelled out money and has to have band-aids left, right and center. Went to Sears to ask for a refund. They refused because tech guy wont give a report to them (but what do we really know eh? Because the tech guy stood in my kitchen and gave a verbal report to Sears but nothing written). So Im in the hole for a crap product that is only a few weeks old and Whirlpool and Sears have got us over a barrel. The tech guy said he was going to challenge their tech line now because hes upset at how many of these band-aid fridges hes seeing now. I want a different brand and model and cant have it because Sears dont have it. In dire straits now.

My Whirlpool Cabrio has been a real workhorse of a machine. It has been able to take large loads and small loads and get them equally clean and fresh. This was a more expensive model but it was worth the purchase price as I have used the various features provided. I also have appreciated that if you leave clothes on the washer overnight they are still fresh in the morning.

We purchased this water heater (Whirlpool 50 gallon, 9-year warranty, Regular Electric Water Heater, Model Number ES50R92-45D) in July 2015 when Lowes had a special financing offer. Doing other remodeling in the house, we didnt have it installed until the beginning of November. A local licensed plumber installed this for us and we havent had a hot shower since. We have called Whirlpool at least five times. Theyve had us replace the elements, replace the electronic thermostat AND the regular thermostat, then they even had us call a warranty plumber they use to inspect the tank and authorize what needs to be done next. When he arrived, he said he hadnt ever even SEEN this model before. Being fed-up with cold showers, I called Lowes to see if we could just take the thing back to the store, but they said that since it was after the 90 days, I would have to get an authorization number from Whirlpool. I just spent another 20 minutes on the phone with Whirlpool explaining my situation and they said that they cant authorize the return of a tank that can be repaired. I then asked if we didnt have a money back guarantee and the guy said, Unfortunately NO. He then suggested I call the plumber they had recommended to come out and look at it again. The guy was from Tampa and when he was here, he just wanted to get home since it was nearly 5 PM AND hes the one who said he had never seen this model before. What would be the point of calling him AGAIN??? When I buy a BRAND NEW product still in the box from a reputable store, I do NOT expect to have to troubleshoot and fix it. IT SHOULD WORK. Well, I have learned another valuable lesson from the school of hard knocks (and cold showers)...Always read the comments on a product before purchasing.

Purchased a new Whirlpool washer and it has the sensor-- like I am too stupid to decide on the level of water to match my load-- not sure why I got an agitator because I am the only thing it agitates. The clothes just sit there in its own filth and then go in the dryer. Actually put a stained item in the wash to remove the stain and instead it just spread to other clothing and has stained and possibly damaged them. Washing the same clothes 3 times is not saving energy, water and time for me.

I purchased a Whirlpool 12-gallon point-of-use water heater as a booster when I was going to get a tankless and when we decided that we didnt need a tankless, I tried to get an RA number through the manufacturer so that the store could give me credit, as it says directly on the water heater, Do not return to store. They said there is nothing that they will do and it cant be returned to the store. So, what am I supposed to do with this water heater now? Before I knew this was going to happen, I purchased a 50-gallon Whirlpool water heater as well. So now, I have the 50-gallon that I have had to replace the element for already and I have only had it for less than a month and a half, and the 12-gallon is just sitting in my garage. Im completely irritated with this company and do not recommend anyone to go with this company! This is the worst customer service!

This dishwasher is so far advanced from what came with our new home 18 years ago. It is absolutely the quietest machine. You have to look at the light display to know if it is even running. Its a well thought out unit with the exception of the silverware accommodation. They used a flat low-profile basket attached to the inside of the door. Not accommodating enough space wise. Solved by augmenting the more stars compartmentalized basket that came with the old dishwasher. Would recommend and purchase again in a heartbeat!

Ive had my Whirlpool Gold for over a decade and absolutely love the quality and performance of the unit. No maintenance issues whatsoever throughout the years. I recommend this washer to everyone I know and continue to enjoy the performance and reliability of Whirlpool. I will continue to buy this brand every time as needed.

I bought this Whirlpool Cabrio Washer 3 years ago. Yesterday will be my last repair. I installed a new tub (bearing failed have to buy a full tub to replace), new suspension rods and a new stator and rotor (cracked). Last year I replaced a drain pump twice, and a computer board. All of these repairs since I purchased this washer have cost me well over $900 for a $1400 machine. I dont mind replacing a pump every few years but these larger failures are unacceptable. We have moved back to Kenmore on some new appliances we purchased this year as result of trouble with Whirlpool. Whirlpool should send out a recall on the suspension rods; the existing ones seize at the top and stop functioning causing the tub to shake excessively. This led to the cracked motor (rotor cracked).

This machine is 18 months old. First it failed to drain (LD code). Ran diagnostics and found the drain pump ($60) failed. The Mexican part was replaced with an Italian part. Two weeks later, the infamous F1 code flashed - control board. I sourced a new one. I ran one load and another F1 code is flashing. These are $150 electronic parts. Fuhgetaboutit. Im sending this ** to the dump and going back to electromechanical controls. I had a Maytag that lasted 15 years.

The machine Will Not Clean the Clothes. Had to Buy A Maytag Washer.

Purchased a G16SDRXX07 three door Whirlpool refrigerator two years ago. Ever since new, when there is a very short power glitch the refrigerator shuts down and will not re-start without manual intervention. This happened at two months. Whirlpool replaced the boards. Still does it. Also when this happens the water dispenser will no longer dispense continuous water. It stops after three ounces. Now they want to charge me for a service call and parts to correct a problem that is obviously built into the unit. There should be a recall on this. Whirlpool should correct the problem free of charge as it is obviously an electronic design issue. Upgrade the necessary control board and replace it. If not, after being a loyal Whirlpool customer for 42 years, we will replace this unit with a different brand that Whirlpool does not build.

Once again I am disappointed in a product that I felt was of the utmost quality. However after buying in 2010 and not being installed until 2011, the over the oven microwave has a crack on the outside of the door. Two pieces have fallen off from under the plastic rim on the inside of the door, two pieces of the door one on the top right side and the other on the bottom right side have fallen off. All I have to say is the two Whirlpool products I bought at Lowes has been a huge disappointment especially since the other two bought from the same stores are Frigidaires and work beautifully...

Our ice maker was not producing ice. Whirlpool Warranty sent a co. Kens Appliance Services to our home. The repairman diagnosed freon leak. When he came back on Oct. 7 with parts he blowtorched the electronic board & wires while fridge was plugged in. We still dont have refrigerator weeks later. We are buying food & ice every day. The next co. they sent werent licensed to add freon. He verified burnt board. Third company they sent told Whirlpool warranty to replace our fridge. They tried to sell our warranty back instead.

We originally became alarmed by an awful smell and noticed that our Whirlpool Conquest side-by-side refrigerator freezer/fridge was not keeping food items cold. Upon further inspection, we saw that the compressor starter in had started fire and melted. Our refrigerator model #GS6SHAXLS42 and serial #SM3832794.

Have a Whirlpool side-by-side with water and ice dispenser on the door. It has lasted over 20 years. It has a large ice maker which makes more than enough ice and it has never broken. Since it is older it does not have gallon depth shelves on the door, but I have never missed not having them there is plenty of internal shelf space.

Purchased washer 8/2015. Washer quit working 12/2015. Would not drain or do anything. Repairman dispatched and came 3 business days later. (They dont work weekends.) Repairman looked at old receptacle cover and immediately stated, Problem with polarity of plug. No prior problems with plug running appliances. Plugged into it for over 8 years. When I advised him of that then he started troubleshooting circuit board. He cleaned out the machine and got it to work. (Still under warranty) 4 days from repair, and machine quits. Same problem. Wont drain and wont do anything. Call for service again on Weds. morning and given following Tues for service call. Online consumer reports complaints #ered at over 1,7000. Same machine, same problems. Call Whirlpool directly, given runaround. Talk to Whirlpool mgr. (Robert) complaint # **. He states, Have to wait for service. But calls Brandt Melb., FL to try to get sooner service. Brandt calls me stating they have ordered a lid lock and CCU board for machine and will be out Monday. How would they know to order these parts if it is not a constant issue? Im thinking class action suit for shoddy product... LOWES Indian Harbour Beach, FL. Transaction #**.

I have a similar problem with my stainless steel Whirlpool bottom freezer refrigerator, model EB9FVHRWS01, purchased in May 2011 from Sears Canada. Exactly a year later, right after the warranty expired, I started getting ice forming on the floor under the bottom freezer. I have been cleaning it out on a weekly basis for the past just over a year. If I dont clean it out, then water seeps out onto the floor. I purchased an extended warranty for my new stove but didnt for my fridge.A co-worker had the exact same problem, with ice forming on the bottom freezer exactly a year later. He purchased the extended warranty and had the Sears repairman come in and replace a $50 part (box in back) ($150 labour). The repairman said this is a manufacturers defect in these fridges and theyve had many such cases. Apparently, the box in the back freezes up and water cant drain to where its supposed to go to be evaporated so it drips to the bottom of the freezer. I contacted Whirlpool and inquired, and they said there was no defect or noted problems with my model. Now Im contemplating whether or not I should spend the $200 and get the defective part replaced. Sigh.

I bought one of the top of the line Maytag washers and was very disappointed. It only lasted about 5 years and had to be replaced. The dryer I bought at the same time is still working. It is 15 years old.

Without being too critical, I would not recommend this washer for medium to large loads or for throw blankets. I have to wash throw blankets 2 to 3 times to get the entire blanket wet even on deep water cycle. I would not buy this washer again.

I thought the new AquaLift cleaning would be the greatest. Boy, was I disappointed -- no thoroughly disgusted and very angry -- when I tried to use the self cleaning oven. I had cooked a prime rib roast and a lot of grease had spattered inside the oven. I wiped away the excess and did a cleaning cycle -- what a joke! There was still grease running down the door and walls. Nothing was changed after two cleaning cycles. Now I have to crawl inside the oven and scrub it manually. I was always pleased with the old self cleaning ovens which only left some ash and a little bit to clean up. The AquaLift technology doesnt work at all, didnt Whirlpool test it prior to selling it to the public? They will surely lose my business and I hope a lot of other peoples business as well. This technology was a huge mistake!!

I bought what I thought was a great washing machine. It is a top loading Cabrio from Whirlpool. The machine leaves white residue on all my dark clothing. It is a disaster. I am following washing instructions exactly, using HE detergent, loading the right amount, I even tried using PODS. I tried different temperature water, different cycles of washing and spinning and the same thing happens. I had an old Maytag that broke that cleaned beautifully. This thing is a piece of garbage and I would love to send it back if they would let me. DO NOT BUY IT. I AM BEGGING YOU, YOU WILL BE VERY UPSET.

Does everything its supposed to except get the clothes clean! Nothing gets clean, even on bulky setting when theres supposed to be more water in the machine!

I bought a Whirlpool Cabrio Platinum washer 2 years ago and it is by far the worst washer I have ever owned. Its a water saving device with extremely long cycles. The clothes dont get wet enough, dont come out clean and they do not smell fresh. I have to put them through 3 rinse cycles and often times have to re-wash my clothing. The cycles are very long, using more electricity, and it takes me 3 times as long to get my weekly laundry done. My clothing comes out more wrinkled and twisted causing longer time ironing. My old agitator style washer did a superior job compared to this piece of junk. I dont like the automatic locking lid, nor do I like the machine choosing the spin cycle for me. There isnt even a soak cycle. If I want to soak my things I have to do it in the sink and then drag them to the washer to rinse and spin them.I spend a fortune on laundry additives in order to get my clothing clean and then they arent as clean as with my old washer. I now dread doing laundry and every time I look at the washer I feel like taking it to the dump! There isnt anything I like about this machine and I wouldnt recommend it to anyone. It is a piece of crap. This is 2016 and they havent learned how to make a good working washing machine. When I move, I will be celebrating leaving it here! I will never, ever buy a product made by them again.

I have 2 dishwashers. A stainless Quiet Partner III & a plastic Quiet partner II. The Partner III never gets the glasses completely clean. The cheaper Partner II gets everything clean but has had several service issues.

I bought model #W4TXNWFWQ at Lowes in February 2013. It had a one-year warranty. Five months after the warranty expired, the defrost timer went out. It cost $100 to fix the $400 refrigerator. Planned obsolescence or coincidence? Either way, its poor quality.

At after 4 years of use, my double door refrigerator is giving cooling problem. Upper refrigerator part has excessive cooling and lower part has no cooling... after complaints in customer care, engineer was sent who changed the part that regulates auto cut... it gets blocked by ice so cooling air is not reaching lower part. Once changed exactly after 5 days same problem started... In spite of complaints no one came to check for good 2 wks. After long fight, it was defective board that was changed again. After 3 days same problem again, board was changed... Now after 2 and half month same problem. And now today service center has replied that engineer will be sent after one week.

Whirlpool should be ashamed for making a terrible machine. It does not get the clothes clean and it is always breaking down. It is not worth the money. I have never ever had a washing machine act like this. I have been RIPPED OFF!!

We purchased a Whirlpool Gold Induction range, model#WF1910H0AS0, from Lowes Home Center for ~$1700.00, about 1.5 yrs ago. One night my wife was cooking dinner on the stovetop and she heard 2 loud pops and the whole cooktop went dead. We had Bobals appliances repair look at the range and they gave us an estimate of $800.00!! to replace the module board. The repairman said the module board had shorted out and burned. Thankfully my wife wasnt electrocuted. I contacted Whirlpool customer service, they said, There isnt anything they can do. The warranty is only 1 year. I also contacted Lowes customer service. They told me the same thing as Whirlpool, nothing they can do, 1 year warranty, etc. I have the part# of the module in the stove, W10390743, serial#31811552. After an internet search, this part # had been superseded, which tells me Whirlpool knows they have a problem. These ranges need to be recalled. I plan to contact the US consumer product safety commission to initiate a recall. Please inform consumers if they have this Whirlpool induction range with this problem, to also notify the Consumer product safety commission.

I just bought a house that has one of these ranges, and it was getting the F2 message. I found the problem. There is NO ventilation behind the electronic control so when the oven heats up, the control board gets too hot and throws the F2 code. That would indicate a bad temp sensor or bad board, but really its the heat shield on the back. Ive removed the metal plate from behind the control panel and it works fine now. Im considering drilling some vent holes and adding some insulation behind the control.

We were at end of cooking salmon in CorningWare and the door blew open with amazing force!!! It is a double oven... Sounds like Whirlpool doesnt care so trust me we are not buying one ever again. :(

We spent a lot of time researching to make sure we were making the right choice, found the one that was right for us. When it got delivered there was a problem though, the plastic scratch protector film they put on the doors for delivery left an adhesive residue that looked like dull spots all over our new shiny black doors. I immediately opened up the owners manual to see how they recommend removing this blotchy sticky residue, assuming we werent the first ones to ever come across this problem, unfortunately they only provide generic cleaning tips. So I went to their website and found what I was looking for. I tried all of the cleaning methods they provide, none of them even came close to working. So I grabbed some adhesive remover and tried that, it worked great to remove the residue however my microfiber cloth (which they recommend explicitly) started leaving scratches all over the finish.I called the customer service to see about getting a new door delivered, thinking this wont be more than a 5 minute phone call since I had followed all of their steps they provide both in the owners manual and on their website. Heres where I find out that their policy DOES NOT cover scratches/cosmetic damage, period. I tried reasoning with them, I had them read their own recommended cleaning procedures, and we both concluded that I had followed their procedures to the T! You might think that if the all of the typical procedures didnt resolve the issue, that would be the point where the customer service reps would have the ability to make a decision that satisfy the customer, you would be wrong! They kept telling me over and over that their policy doesnt cover cosmetic, therefore there was nothing they could do. It was delivered with a defect of sorts, how is the customer responsible for that? The only way I can see it having worked out in my favor is if I had never tried to clean it myself and immediately called customer service, I still fear they would have given me the same line of cosmetic damages are not covered even if I would have tried each procedure with them walking me thru it over the phone. Lesson learned, I will never purchase another Whirlpool product!

This Whirlpool top load washer has been an awesome product. I have had it for 9 years and havent had a bit of trouble. Its very quiet and very reliable. The only maintenance is running a cleaning tablet on the cleaning setting once per month, and it tells you when its due... No musty smell problems that I hear from people with front loaders. Its a great product.

Whirlpool Refrigerator 36 inch #WRF993FIF. We have owned refrigerator for 3 months and both ice makers went out. Worst customer service ever with Whirlpool and their appliance specialists. Ordered new ice maker, but still broken. Whirlpool is saying it needs a new door!!! I have asked for a new refrigerator, but cant get anyone to respond. I have called 6 times being on hold one time for over 30 minutes trying to get a scheduled appointment for a new door! This is by far the worst service that I have ever received from a company.

Very functional microwave which also comes in convection oven if needed. Stainless steel, finger print resistant, is very handy and easy to clean. Overall very happy with it so far. Much better than the earlier Samsung that we had.

I spent what I consider to be a lot of money on the Whirlpool Cabrio washer and dryer which I purchased in 2007. Within months, I was getting error messages on the washer, specifically an F51. Thankfully, it was covered by warranty. Whirlpool knew then and there that these things were lemons. The repairman told me he couldnt keep up with fixing that issue. I have since had to replace the motherboard on the washer at a cost of $359, and the idler pulley on the dryer at $221; not to mention the metal catch on the dryer broke. I ordered a plastic one on eBay. I will never buy another Whirlpool product as long as I live! They make junk!

I recently purchased a Whirlpool refrigerator, model number WRT351SFYB00. Several months later, I noticed a small amount of water on my kitchen floor. I moved the refrigerator and found the hard wood floor under it had been completely ruined, so the leak had obviously been going on for a long time. Possibly since day one. I called a repair man. He identified the leak was coming from a cracked drip tray which was not uncommon. However, much to his surprise, due to the design of this model, he was unable to remove and replace the tray. He explained there was a metal panel bolted in place that was preventing him from replacing it. He said this panel was also bolted to the compressor. Therefore, the best he could do was caulk whatever cracks he found in the existing tray and hope for the best. It goes without saying he could not guarantee his work like he normally does.I noticed this same complaint on a user forum website on Appliancepartspros.com, so this refrigerator obviously has a significant design flaw. My repairman said if it was his refrigerator, hed get rid of it, and also indicated that after seeing this, hed never again recommend Whirlpool to anyone. All I know is that Whirlpool is permanently off of my list now as well.

I bought a dishwasher with a 5 year warranty. It broke just after one year of purchase and they are giving me the runaround with replacing after finding that the part the part needed to repair machine is no longer available. The warranty clearly states that they will repair or replace with same or comparable machine and they are refusing to do so. I am at my wits end and I have no one to turn to within Whirlpool as they say it is their decision how they want to handle warranty.

I purchased a 50 gallon Whirlpool water heater, model FG1J5040T3, in November, 2005, and have had the same experience as reported by the hundreds of others, whose comments I have been reading. Basically, pilot wont stay lit. I called Whirlpool, relight the heater, when it doesnt relight, wait to receive repair parts, call a plumber, and pay to have them install it, then repeat same problems. Each time going for a week or so, without hot water.After relighting the heater 10 times in the past year, and service calls, Whirlpool authorized me yesterday to return it to Lowes, and get a replacement. I need to hire a plumber to unhook it, haul it to Lowes, get the new one, and install it. It cost me about $300 to $400. Will the replacement be any better? I am considering just replacing the heater with one made by Rheem.

I bought a Whirlpool WFW9470 Front Loader Washing Machine 11 months ago. The washer appears to complete a wash cycle but leaves the washing wet and with no error message or light. Whirlpool says the machine is not designed for light loads. The technician says washing on a light load will damage the bearing. We had the spin bearing replaced after 8 months. But still, the washing remains wet and the bearing wears out prematurely.

WRF989SDAB00 - Our house burnt down in April 2012. We purchased all Whirlpool products to be put back into our house. We had to purchase these items in November 2012 so the contractor could get them into our house because of the cabinets. We did not move into our house until the last week of December and could not use these items until then. In December of 2013, our freezer went out along with the ice maker. I had to fight for Whirlpool to pay for these repairs. They kept saying that it was over the one year warranty. They did accept responsibility and paid for A&E to come look at the frig. One guy came out the first time and thought he fixed it. No. A month later two guys came out. They said it was the condenser. They ordered the parts and came back a third time to replace it. A month and a half later, same problem. A&E came out a fourth time and thought they fixed it again. Nope. During this period, I purchased a extended service plan. I AM TELLING EVERYONE TO DO THIS NOW BECAUSE IT TAKES 60 DAYS FOR THIS PLAN TO TAKE EFFECT. Now the service plan people sent a different company out and he said it is going to cost a lot of money because the things that need to be replaced. The plan SHOULD cover all of this. I called both the service company and Whirlpool demanding that they send us a replacement frig. I believe sending someone out at least SIX TIMES to fix the same problem is ridiculous. Each company is blaming the other and each is saying its the others responsibility to replace the frig.

Purchased from Home Depot and self-installed. That part was not too big a deal but after installing this stove we started a journey of irritation, aggravation and general dissatisfaction. This stove has the standard layout for burners that seem to be common to most low-end stoves. Two huge burners in the front, a simmer burner at the right rear and a general purpose burner at the left rear. Thats all wrong for me and our set up. I want a large burner at the left rear and general purpose every place else. Can you alter the standard configuration? NO! Not without some major alterations to the stove top.Next are the grills or cast cooktops (2 each). They are a bit cumbersome when cleaning the stove but doable. The real problem with the grills are Whirlpool decided to save money by skimping on this feature. The grills are not a stable cooking platform for smaller pans and it turns out Whirlpool recommends square pans for this stove. SAY WHAT? I have pans and skillets from my grandparents and they are ALL round. Thats how that stuff is made. ROUND! The grills design is unstable for any round pot, pan or skillet, if its diameter, is 6 or less. Kiss that excellent saucepan goodbye if you have this stove. My current solution is a piece of light expanded steel over the burner areas.Keeping in mind we use Propane as our heating gas. The adjustment of the flame temp on the four burners is non-existent. They all are either on high, medium or low. There seems to be no fine tuning with these burners. At the end of the day go look for something that is NOT a Whirlpool, LP gas range Model #: WFG515S0EW. You will be better served and less irritable with almost anything else. Even a campfire in the yard is a better choice.

I have the same problems as the ones listed in complaint section. I bought 4 Whirlpool products at the same time: refrigerator, stove, and the Whirlpool duet. Washer is a front loader. We have had nothing but trouble. The company we bought the machine from exchanged the washer for the same model because the electrical was bad and the parts to replace were back ordered for more than 3 months. We are now having problems with the exchange washer. This time it is the same as the engineer remarked in his complaint the bearings are bad and it sounds like a jet taking off. It’s that loud.I went down to the place of purchase and I am in the process for the repair. I have a feeling this will not end well. Whirlpool, if you call them, gives you a run around or tells you they dont have you listed in there computer. We dont have the money to replace any of this. This new machine is only 9 months old. Whirlpool is making a killing off of fixed income people and the working class. You tell me who can afford the cost of that kind of repair or the cost of a new machine that only works for a couple of months. Why is 60 Minutes not on them like a bad smell?

I am very disappointed in my Cabrio washer. I have had it for two year and now I have to spend $ 250.00 on a machine that sounds like Im in a machine factory. It is so loud in the spin cycle that you cant hear a TV or radio. Also the lit of the washer broke in the start of the second year. I had my previous washer for 15 years before requiring a service call. I have to agree with all the reviews that this washer should be recalled. Maybe if we all call the media in on this problem Whirlpool will be forced to pay for a recall or repairs. Another case of big business ripping off the consumer.

In 2013 my oven died. Upon doing some research my husband and I went to our local appliance stores in search of a new one for a good deal. We chose a Whirlpool electric range with convection oven. We have had it 2 1/2 yrs and have used it often... until today we had been very happy with it. While baking some French fries we heard a loud pop, almost like a shot, running to the kitchen to find the inside tempered glass shattered! Wow! Shocked to say the least we couldnt believe it. Called our Lowes store, to no avail our warranty had expired. They gave us Whirlpools number with no success. I am extremely disappointed and will probably never buy Whirlpool again!

I purchased a brand new washing machine and had service come to repair the machine approximately five times within the first year. Every time the machine was repaired, it was for different reasons. I contacted the main office and spoke to a woman named Sherry who is a supervisor and she was very nasty. This is a brand new machine and I feel that it should be replaced with a new one. Sherry said that there was nothing she can do for me. Is there a lemon law for appliances? The machine is used for my son and me only. I have all appliances in my house by General Electric and this is my first and last experience with Whirlpool.

The clock-timer went out. Appliance is only 1yr. 6mo. old. I CONSIDER THIS STILL A NEW APPLIANCE. This is the 2nd Whirlpool appliance, I bought a Whirlpool washer & dryer. The washer went after 2yrs. use. I bought a Kenmore used washer and it still works. I paid cash for the stove. It was bought at a Sears outlet in Cudahy, WI for $398.58 total with the one year warranty. I really have not gotten the use of the price. I guarantee you (this company) I will NEVER buy another Whirlpool appliance again. TOO BAD YOU COULD NOT RETURN A PARTIAL OF THIS MONEY TOO ME!!!!! I have a Sears repairman coming today 8-3-13 costing me $75.00 just to walk in the door.

Whirlpool dryer and washers have the worst reliability, plus terrible customer service. Parts missing from factory install to faulty parts that constantly need to be replaced. Wasting precious time to meet with service repair people. Not worth it. Make products that are reliable and be accountable.

NU40T61-403 have had problems since day one. First problem was while heating up would make loud humming noise. Whirlpool sent out plumber. He adjusted plate under tank. That worked for about 2 months. Then pilot started going out. They send same plumber out again, also sent replacement part. Problem was fixed however about 2 months after that started leaking and flooding our garage. Called company again, was told that is no longer under warranty and stated we need a thermal expansion tank. I stated “why would we need this? This unit is only a little over a year old. Im not going to purchase another tank. A water heater should not overheat like this.” Long story short my husband has been burnt severely from the pressure build up as he was out in our garage walking past the tank when it decided to release pressure even though no water was being used at that time. He ended up at the ER with 2nd-3rd degree burns. I called Whirlpool again and was only told we need to install the expansion tank. Im so unhappy with this product I will never buy anything made by whirlpool again.....

This is our second Whirlpool refrigerator that has the same defrost water drainage problem. I was told this newer model had updated technology, not so, actually it is worse. My older refrigerator went about 8 years before I started noticing water on the floor and this newer model is 4 years old and it started having water overflow at 3 1/2 years. Then in April we replaced the water filter and the ice-maker stopped working. My freezer also stinks like stale water (my reason for replacing the old refrigerator plus the water on the floor). I followed a YouTube video for defrosting the drainpipe, it was very tedious, labor intensive, and time consuming and worked for 3 weeks. This is very upsetting. After spending $2500 to have such problems and my expensive $150 4-year extended warranty expired just weeks before the ice-maker went out. This is obviously a design problem that Whirlpool refuses to address since my other model was a year 2000 model and my 2013 has the exact same problem. VERY POOR customer care in addressing these design failures of both the defrost drainage (just make a larger drain port!!!) and the ice-maker.

Whirlpool Washer WTW8700EC + Dryer WGD8700EC. Bought to replace a 35-year-old Whirlpool set that is still working and had no repairs in that 35 years of ownership. Gave to family member and its working well. Was not a cheap item but well worth the money. It performs beautifully. I chose Whirlpool. It is a proven brand with a long history of reliability. When I bought my last Whirlpool, I bought the top of the line model washer and dryer. They say you get what you pay for and that holds true in my case as has with many others who believe it! So this time I did the same thing and bought the best top loader they had. It has many options I still need to learn. I just use it like the old machine and dont need to worry about types of fabrics or making mistakes. Just follow the instructions for detergent and softeners and all is good. This machine cleans as great as the old one without beating the clothes to death. New agitator design keeps from paddling the clothes, so I dont need to use the gentle cycle or medium to preserve the clothes. The dryer I can say is most efficient as I noticed it took far less time to dry, and notice a small drop in my electric bill and gas bill. I think this will be my last machine ever needed. I do take care of my things and I do clean and polish my machines, they are an investment like a car or house. Front loaders have a lot of problems with leaks from the doors. Will stick with top load only!

Does clean well but I notice that even on heat drying there is still water on the inside of the door when I open it. I have loaded it up and even the glass baking pans came out sparkling. I would recommend this middle of the road priced dishwasher.

I purchased this Whirlpool washer (model WTW7600XW2) on October 2011. Fabric softener dispenser is full of water at end of cycle. Repairman has replaced parts three times, but the problem is still not corrected. Today, I talked with a Whirlpool supervisor. She says this is normal. She told me to take the cup out and empty it. The cup is not removable, so she said I could blot it out with a cloth or sponge. I paid $800.00 for a washer with an automatic fabric dispenser that I must empty manually. I have used whirlpool appliances for 50 years of marriage, but this is my last one. I am very disappointed with customer service.

Whirlpool sent out a repairman to fix my range. I had it for 3 years, and one day I was baking cookies in the lower range and boiling water for pasta on the top left burner. There was a very loud pop, a bright flash in the glass top where the back left burner is, then there was no power to the range or oven at all. No clock display, burners would not work, oven would not work, nothing. As if it were unplugged. Of course, my warranty was about to expire in approximately 6 days (go figure) so I called the customer service line for repair. After 2 hours of back and forth with 3 different people, I finally had a technician coming out 4 days later. He shows up, takes about 35 minutes to get the glass top off, then says to me that he needs to order a part for it. This will take a few days. Ugh. Fine. 3 days later, part comes in. Same guy comes back out, fixes it. Ok.Up and running fine for about a year and 2 months. Then... POP! It happens again. Same scenario, different menu. (I was cooking breakfast). Now, warranty has run out and I have a $1,300 piece of scrap metal sitting in my kitchen. Worthless. My old KitchenAid stove was great. Had that thing for 13 years. Never a problem outside of replacing a $68 heating element one time. I paid $450 for that range. Tossed it out for this bells and whistles newer stainless steel glass top range/double oven. Regretting that tremendously. Whirlpool will be on my do-not-buy list for any appliance from now on. Didn’t even last 5 years. Oh did I mention the service call cost me $85? Yeah... Garbage!

Very durable. Not pretty but will last a long time. The dishwasher will run forever. The appearance is bland so the product is nothing fancy. It gets the job done. The machine is very quiet. I think this feature is the best one.

I would like to invite everyone on here to join me in a moment of silence. My Cabrio has died after a little over 2 years of pure torture that I purchased for $1000 from Lowes. I have had nothing but problems since the day I bought this washer. I think Whirlpool needs to step up to the plate and take responsibility for the mistakes they have made. I will never purchase another product that is in anyway associated with the Whirlpool company. I wish I had my little washer that only needed a new switch back. I guess I am off to find a replacement for this $1000 mistake that I made. If I had the resources, I would file a lawsuit against Whirlpool myself.

We bought Whirlpool Gold Series on July 6, 2014. Refrigerator, range, microwave & dishwasher. Our refrigerator - we have the repair company out almost every month cause the icemaker was constantly icing up and wasnt making the ice cubes single, would come out all attached to each other. So after arguing with Lowes and Whirlpool we were able to get a different refrigerator in February of 2015. Now in April 2015 we are having trouble with our microwave with the light flickering off and on when we open the door and sometimes it work and sometimes it doesnt. The repair company has been out 3 times for the same problem telling me that where the door closes are 2 latches that when not lined up cause this issue, so the repair company replaced the 2 latches and a month later it started happening again. So they came out and replaced the light socket. Now we will see how long that last.Now for the range which is the AquaLift Self-Cleaning which doesnt clean the oven at all. It was like I was back in the early 1950s, only worse. The baked on grease spots, you cannot get off at all. To me this is false advertising and the stores personnel lied to about all you have to do is pour 2 cups of water in the bottom of the oven, press the self-cleaning button and after 40 minutes of cleaning and letting the oven cool a bit you just have to wipe the oven down with a damp cloth and the oven is clean. Not so much!!!Wish I had all my old appliances back because they were made to work correctly. The new appliances suck for the amount of money you pay for them. So please beware and do research on the appliances you want to purchases otherwise you will get ripped off with no satisfaction for your hard earned money you spent on them. I have always had Whirlpool appliances and have loved them but these new ones we purchased are nothing but junk.

Whirlpool Energy Saver Dishwasher Model DU850SWPS3 was placed in our new home purchased in May of 2010. We just found that this dishwasher had a slow leak in the seal to the motor which has ruined our hardwood floor, subflooring and part of a laminate beam on the floor directly below the washer, plus molding from the water. The leak has been going on sometime it was not noticed until the floor became so soaked from use over a long period of time that we finally saw the leak, by accident, in the basement which we hardly access. The Whirlpool costumer service was no help and would not entertain repairing the dishwasher unless we paid due to the fact it is over the year warranty. This is clearly a defective part in their product and poor workmanship on their part. We should not have to check underneath our new appliances to determine if we have leaking problems because we cannot trust them from failing. I will never purchase another Whirlpool product and will not recommend their products to anyone.

We purchased the microwave. It looked nice and seemed sturdy. I bought a trim kit to make it look Built in. As soon as I finished installing the microwave and kit we tried to use it. My wife could not get the door to open unless she pushed the door button hard several times. I checked to see if the trim kit was causing the problem and it was not. We kept trying to get the door to open as it should but could not make it work correctly. I even used a little lubricant and it did not help. We then looked up the reviews and saw this was a prevalent problem. We then returned the unit and trim and ordered a Samsung. It will be in on the 25th of March. I placed a review on Lowes site but Whirlpool removed it saying since I took it back they removed the negative review. Since it was defective I wanted the public to see the truth on this unit.

After 1 1/2 years, My new Cabrio washer lid hinge started to come apart and wont latch, so machine wont run. After a day or so it completely popped up and out of align. The lid has PLASTIC hinge. This is obviously a problem. We have been in touch with Whirlpool, but they say they cant help?? This should be a recall. We have been waiting on back order for a replacement Lid at OUR OWN EXPENSE since Sept. 20, 2015. I want to get this fixed and use my Machine again. We are Senior Citizens and this machine is used 3-4 times a week. Not abused.

I will never buy a Whirlpool product of any kind. I bought a gas stove and its a piece of **. Won’t even light. Only way to start it is start boil then switch over to bake then it wont light. So please I ask that you make a product thats worth buying.

I purchased a Whirlpool washing machine from PC Richards in Lake Grove 15 months ago. I paid $590.00. I had to call PC Richards back because it sounded like the machine was not spinning right. The servicemen came back and said nothing was wrong. It was supposed to sound like that. Now the machine stopped draining and spinning. I went to the store and they handed me customer service numbers and said they could not help me. I contacted Whirlpool online and received a phone call from a woman that gave me a lesson on how to load the machine and put soap in it! She was a very polite woman, but, gee, that didn’t solve my problem.After 4 days I was able to get through by phone and was told to call service. I contacted Mahler Appliance. He looked at it and said he couldn’t fix it and took a check for $81.47. He told me to call Whirlpool. I called Whirlpool again and got their service people. The gentleman came and could not figure out what was wrong. He tried a few things and said it was probably the main board. He said to call Whirlpool, but they most likely won’t give me back my money. He could charge me $460.00 for a new board per his supervisor. I just paid $590.00 for the machine and another $87.00 to some guy who took advantage. He left with an $87.00 check and I still have a broken washer. He did tighten up a loose wire he said he found and told me to try it and good luck. So I tried it. I put clothes in and turned it on.I came back about 20 minutes later to see if it continued to run and I slipped and fell on the ceramic floor because water drained out from somewhere and went all over my floor. I have injured my back and elbow from hitting the hard floor. I also have water all over the place and finally a very broken defective washer. I am angry. I hurt myself and have spent close to $1000.00 and I still have no working washer and no way to buy another one. The washer is 15 months old. That’s brand new to me. There was obviously a problem from the beginning. Whirlpool has always had a quality name for years. I would hope that they would stand by their product and fix my washer for me. It is obviously defective.

This Maytag dishwasher is awful. The parent company is Whirlpool and their customer service is as bad as their products. I bought this dishwasher and less than a week later the pump isnt working and stagnant water is sitting in the machine. It took Whirlpool 3 weeks to replace the machine and they sent over another defective machine. This time it lasted less than 2 days. The Whirlpool customer reps are rude and vindictive and antagonize the customer with their lack of service. Called corporate office with no help from Cust. Service and was told to leave a message with the operator and await a callback. With this fiasco I wouldnt buy another Whirlpool or Maytag product again. BTW. Im still awaiting my callback from the corporate office... Im not holding my breath. I called the company that I bought the dishwasher from to see if they can help me unload this machine and get a different brand...

After 22 years, I replaced my Whirlpool, electric, 50 gallon water heater, due to age and it was still working well. Went to Lowe's and they do not carry Whirlpool any longer, so I purchased and installed an A.O. Smith water heater, electric, 50 gallon water heater, model ES12-50R55DV110. Hoping for as good a product now, as I had from my Whirlpool. Also, I installed myself.

Whirlpool Gold GC3SHAXVBOO - Two issues in two years. We purchased this refrigerator online through Whirlpool in April 2010. Almost a year later, a circuit board went. This was repaired under warranty. Our refrigerator was making loud cycling noises and we were told this was normal. Now a year later, again we have an issue. This time its the compressor. We called customer service and were told there is nothing they can do. The cost to fix approximately is $700. This is very upsetting to buy a $2000 refrigerator and have two major issues within two years and then not have the company stand by their product. I would wonder how many other people have this model and have these issues as it seems like a lot. Whirlpool customer service is terrible, non-caring and offered no assistance.

Washes great. Love the literal bells and whistles. Never has failed to give the family a very clean wash. Price was great and got the matching dryer too. I have heard prices have gone up but this washer is worth every penny.

I had ancient appliances (refrigerator, microwave, range, and dishwasher) that were all mismatched and were in the house when I purchased it in the mid 1990s. I saved up my money and even though my old appliances were working fine, I wanted stainless steel and everything to match so I decided to go ahead and replace my refrigerator, microwave, range, and dishwasher. I decided on Whirlpool since the company has been making appliances for many years and I thought they made a good product. I bought those appliances in 2012.In 2015, the microwave started to malfunction. At first, it would light up and act as though it was working, but it wasnt. I had it repaired - they said it was a fuse - and the fuse repair cost me about $75.00. It worked for about 2-weeks. I called the repair guy back and they didnt charge me, thinking it was something they did wrong when they fixed it. This time it worked for about a week when it went out again. Not wanting to miss any more work waiting on a repair guy, I went to Lowes and bought a pack of the appropriate microwave fuses and replaced the fuse myself. This time it worked about three weeks - I noticed it was popcorn that seemed to kill the microwave. I finally gave up repairing it when I used up all the fuses in the pack from Lowes. I bought a GE Microwave and it has been a dream. It does a better job all around and looks a lot better than the Whirlpool. I no longer have matching appliances but at least they work!But thats not all. Now the Whirlpool refrigerator has been slowly dying. It has been groaning and creaking since I had it installed but it has gotten so loud that I have to sleep with white noise so that it doesnt wake me up. Yesterday, I took out a Drumstick ice cream cone from the freezer - they are the cones that have chocolate covered ice cream with nuts. I bit into the chocolate coating and the ice cream all spilled out like milk! Looks like Whirlpool struck again and I am not even going to bother to repair it. I just hope I dont get food poisoning until I can get it replaced. And...the dishwasher. Well, it wont dispense the Jet Dry liquid if I fill up the reservoir. I have to fill it only half way or it wont work. I had to use an eyedropper to get the tank down to half. It doesnt really get the dishes clean either. My 20+ year old one I got rid of was 100% better than this Whirlpool dishwasher.Luckily, I hardly ever use the range...and when I do, its a burner or two so I havent had any problem with it yet. I am thinking of replacing it anyway simply because I dont want - ever - anything that says Whirlpool in my home. I was so excited when I decided to buy new appliances. I was finally going to have something new and nice in my home...or so I thought. Instead I wasted my money and got aggravation instead of joy. I dont know about others but I will never buy Whirlpool appliances again- never ever. And now I feel like my money was stolen from me -- and my joy definitely was stolen.

My Whirlpool super capacity 465 started flaking out on the temperature and burned our dinner. I had a repairman over to repair which he did after about 3 hours of testing. Less than 6 months later it did the same thing. Overheating in the oven.

I am so thankful that there are others who are having the same problems with their washers. Since 2006, my husband and I have had words regarding who is not loading the washer right, why are the clothes still dirty, and why does the dryer have so much lint. The excessive amount of lint ruined my dryer. I get UL codes all the time! Before the UL flashes, it sounds like someones trying to break in. It is 2011. Despite the problems, it has not died yet. I am selling it and will never purchase another from them again. I have the dryer and it went out 2 years ago. It has problems with the motor. You can guess I did not buy a Whirlpool.

I am a Licensed Plumber in Oklahoma, have been for 25 years. Our company will no longer work on Whirlpool water heaters, heres why. I diagnosed a water heater that the pilot would not stay lit, the thermocouple was bad. Whirlpool Tech Support told me to go to Lowes and buy the parts and send them the receipt and they would reimburse me. The customer was furious that I charged them for the part and I told them when I got reimbursed, I would send them the money. Well, I not only never got any money from Whirlpool but I never got paid from the homeowner who was mad at me and I didn’t even sell it to them. Beware, buy Rheem.

I purchased a Whirlpool Refrigerator from Lowes. 21 months later I need to replace the compressor. Whirlpool has been kind enough to cover parts and labor, but it has been 24 days and no service call yet. After multiple calls to their service department, who keep telling me there is not another dealer in my area, I am forced to wait. Living out of coolers for the past 21 days is very frustrating. I wanted to rent a fridge and send them the bill, but they would not cover that. I will never purchase another Whirlpool product in my life and will advise family and friends on the reliability and service I have received.

Purchased the 2015 Whirlpool Cabrio. Today 5-2018, the panel went completely out. When I called the store (Lowes) they asked if I purchased the warranty. I responded no, she went on to say, “Well since you choose not to purchase the warranty youre stuck”. Even if I paid for the warranty a washer should not break down in less than 3 years. My previous washer lasted 18 years with no problems. We purchased this washer because of the larger load. It was one of the most expensive washers. It’s a piece of junk and the manufacturer will not stand by their horrible product. Please DO NOT buy! I will be filing a formal complaint.

Our machine was bought via the employee purchase program. Its just under 2 years old and the bearing has been out for nearly 6 months. I called Whirlpool and our local Whirlpool repairman. They both want hundreds of dollars to repair it. Being pretty handy, my husband and I decided to fix it ourselves. Trying to find compatible parts for this model is a NIGHTMARE. Everything in my house is Whirlpool...range, dishwasher (also junk), microwave, fridge, washer, dryer...and it will all be systematically replaced with ANYTHING BUT WHIRLPOOL OR ITS COUNTERPARTS.

I purchased an OTH microwave model #WMH1163XVQ-1 around 12/2011 from Lowe’s. Within a year, the paint started peeling inside of the microwave on the bottom. A few weeks ago, I noticed flames in the microwave and realized it wasnt my food but the microwave itself was on fire. Im glad I was close by to immediately turn it off. I hate to think what would have happened otherwise. Does anyone have any idea of what I can do about this? Would this still be under warranty? This is the first and last Whirlpool product Ill be purchasing.

My dishwasher control board caught fire yesterday. Noxious fumes and black smoke with popping noises moments after starting it. Was glad we had not gone to bed and glad we were home when it happened. Would not shut off and the door was hot to touch. Had to turn off switch on wall.

I recently purchased the Whirlpool Cabrio washer and it is the worst product ever!! It does not wash the clothes, it tangles it in knots and has ruined all of my clothes because it leaves holes in the clothing. I have had multiple service calls and all of the diagnostics check out. It is a horrible product that should be recalled and Whirlpool customer service does not stand by their product. Their supervisors and customer service is very rude and I will never purchase another Whirlpool product!!! I plan on posting my complaint everywhere possible.

WFW97HEDW, WGD95HEDW American made and equivalent to LG and Kenmore. Size fitted our space available. Price was a bit higher than the Korean models with similar or better features. We bought and returned three consecutive Whirlpool models from Sears. Though we never really got to put the dryers to the test, nor did they fail, the washers were of such a poor quality that they broke down within 1-2 weeks of installation. Eventually we switched to LG and have had no problems. When the Whirlpool fails it locks your clothes inside and to open and retrieve your clothes is just short of impossible. We really, really really wanted to buy the American made brand and we were willing to pay the premium to do so, but these washers were awful.

Ive had this microwave for about a year and a half. Like some others I get the door sign frequently. I open the door and cant turn it on until the light goes on, which can take a minute to two. I have NEVER had problems with any microwave other than this one. I had a problem with the Whirlpool refrigerator too, which was fortunately still under warranty. I bought the fridge, oven and microwave as a deal. Trust me, there is no deal here. I will never buy this brand again. Lesson learned. Given other reviews, I might just buy another brand of microwave. Worth not having the hassle.

When you purchase a Cabrio high efficiency washer dont expect clean clothes! But, you can expect holes, torn and, smelly clothes. It takes a ridiculous amount of time to wash. The machine I purchased has a glass top but its dark and you cant see into the machine so that was a waste of money! If you wash clothes in 1/4 depth of water, nothing gets clean. Who even designed this disaster? I had enough common sense to know it was going to be bad but the salesman at Lowes informed me that ALL washers were high-efficiency and getting a tub full of water days are over. I wish we wouldve just paid for repair and kept my old washer. I hate doing laundry with this machine! I use to be able to wash my blankets, pillows, curtains, throw rugs, even car mats with no problems. Not anymore! This machine couldnt handle it. You ought to see my sheets and shirts when theyre done. They come out twisted up so tight I have to untangle them before they go to dryer. What a horrible nightmare of a machine! If we were not out so much money Id send this machine to the junkyard and get a real washer with realistic amounts of water! How are you saving anything when clothes require 2 times to get somewhat clean??? If youre reading this and considering a high-efficiency washing machine, DONT DO IT!! You will regret it. Im counting the days when I can junk mine!

I got a new Whirlpool dishwasher and it is totally unacceptable. Its supposed to be energy efficient and the eco setting, which is supposed to be the most energy efficient, takes 3 1/2 hours and does not do a good job, doesnt dry the dishes. Ive tried all the settings and some take over 4 hours. I have talked to someone at Whirlpool twice and they say thats the way it works. How can anyone put out a product that doesnt work and get away with it? I had my last Whirlpool for over 12 years and it took not even an hour and did a wonderful job.

Purchased washer and dryer combo on 07-08-2013. I have a family of just 2 now. Under normal conditions I thought the machine should last 12 to 15 years. After 2 years of service the bearing and seal on the tub failed, I had to order parts and rent a tool to install. Then after 3 years had to replace suspension kit for the tub. Now after 3 1/2 years the water drain pump has failed and the sensor on the motor is acting up. This machine listed for $800. I did not purchase extended warranty but I have repaired myself. If I had not repaired myself the cost would have exceeded the cost of new. I have now purchased another makers model machine. I think Whirlpool should buy this machine back.

I purchased a Whirlpool washer (WTW4800Q) in November 2011. Already, it has rust in the tub. The warranty does not cover this. I never really liked the thing since I have had it. It takes much too long. Lid locks and then starts over. Also, warranty is not good. I wouldnt ever buy their product again and suggest no one else should either. I loved Maytag before Whirlpool bought them out. Im putting this one on Craigslist and buying a real washer, a Speed Queen! Yes, Speed Queen has all metal parts and makes a home washer. Just have to find a local dealer. They are there.

Bought a Whirlpool Cabrio washer from Home Depot. It started making noises on the spin cycle 2 months after the purchase. A technician came out and concluded it was a clothes hanger behind the machine making the noise. False. Two days later I tried to wash a load. All the panel lights came on. And then the machine died. No power. The tech came out and tried to run tests but the machine would not respond correctly. Informed it has a bad control. The machine will malfunction even if a button is pressed too long. And then its repairman time again. This machine is poorly designed. No doubt whoever designed the digital control panel did not think about ease of use. The tech has to recalibrate the controls after every failure. Whirlpool and Maytag have put out a bad product and this will be my last.

We purchased our Whirlpool Refrigerator, oven, and microwave a little more than a year ago. Not a single negative event with any of these products and my wife and I wholeheartedly recommend Whirlpool for operation and last ability, unlike the products we replaced them with.

The Whirlpool hot water heater model ES80H123-45D from Lowe’s is a free replacement for a lifetime warranty unit that went bad after 8 years. First heater would heat to 154 degrees with a setting of 150. Very good. New one heats to 140 degrees with a setting 150 degrees. Digital ESM screen on heater reads 150, but the water is only 140 by my temperature test. I talked to complaint line 5 times in 7 days and was told to do various test, but the temp never went past 140. They replaced both thermostats and temperature still never past 140 with ESM reading 150. They first told me standard temperature was plus or minus 5 degree range. Then, they changed their minds and said it was 10 degrees. They are calibrating their equipment to operate 10 degrees less then their Energy Smart module reads to cover up a performance issue with their water heater. They say this unit will operate between 80 and 150 degrees—nothing’s said about a plus or minus operating range. I will buy a new temperature gauge to see if my old one is correct. It was tested against a digital one a couple of years ago when I had a new dishwasher installed by Lowes. The installers gauge read over 152 and mine read 154 degrees at the sink next to the new dishwasher, so it was close to accurate at that time. Whirlpool is happy with their under-performance.

I purchased a 50-gallon Whirlpool natural gas water heater (12 year warranty) from Lowes approx 2.5 years ago. Just before Thanksgiving, the pilot light started going out once a day, then twice a day. Now, I can light the pilot light in Pilot mode but as soon as I release the red button, the flame goes out. I called Whirlpool and received phone troubleshooting support resulting in a recommendation to pick up a new thermocoupler from Lowes which I did. While searching for someone to install (unfortunately Im not that handy), I ran into the thousands of complaints filed about the very same problem Im having over a number of years and right up to todays date. I called Whirlpool back and got the same song and dance. Theyd be happy to help me troubleshoot if I can get the required meters etc. to test devices, do draft tests, etc. They claimed the problems were fixed with the newer model that I have but certainly cant explain why I have exactly the same issue. What they are not willing to do is stand behind their product and get me hot water. Tried calling Lowes and got the response that I have to deal with Whirlpool. It appears that this newer BFG model is just as flawed as the older model and the warranty is pretty much worthless other than getting a few parts. I used to think that Whirlpool products were reasonably good, however, I will never purchase another.

In 2011, I bought in Croatia, for the start, 2 washers (model 3LCHW9100WQ) and 1 dryer (model 3LCED9100WQ) and opened the first self-service laundry in Pula, Croatia. Since the beginning, I had problems with the gum (black). After the washing cycles, you could see black lines on the laundry. Whirlpool Croatia denied that the gum can be the cause. After two months, they gave me new gums, but the problem still exists. After 5 months of work, the first malfunction on the washers started. The biggest problem is that it took and still takes them up to a month to repair them. And these problems I have ever since. Also, the error codes never showed the correct malfunction code. In global, if I take that I have these washers and dryer for about a year, they were out of function for more than 3 months. The warranty expired in April 2012. On these reasons, I cannot recommend any product of Whirlpool, and I have to change to another company to buy more washers and dryers.

I bought washing machine Whirlpool Cabrio Model WTW7300XWO two years ago. It only lasted 2 years and the tub seal and tub bearing went bad. I called Whirlpool and they wouldnt replace defective part on their dime. I talked to supervisor and they still refused to admit they needed to fix this broken product on their dime and make it last longer than 2 years. They claimed only a 1-year warranty. This is totally unacceptable to have a supposedly good washer that you pay $700 for (manufacturer price $899) last only 2 years! Very, very disappointed! I wouldnt buy from this company again!

Just like so many on this site Bought Whirlpool Model #WRF990SLAM02 refrigerator new in 7/2013. Just went on vacation for 2 weeks, I come back and the freezer and ice maker are not working. If what everyone on here are saying is true then it looks like I too will have to purchase a new refrigerator and you can bet it wont be a Whirlpool.