We purchased the Whirlpool Duet (front loader) washer and dryer in 2005 from Best Buy. We had many problems with the washer leaking around the front door. After several visits, Best Buy (in 2007) said we could pick out a new washer. We picked out the Whirlpool Cabrio. About 2 years later the mother board had to be replaced on the Cabrio. We are constantly getting F codes and have to unplug the washer several times for it to reset. It also sounds like a plane getting ready to take off and from what I read that repair is very costly. It has been leaking as well. I contacted Whirlpool today and they informed me that there was no recall on the machine and when I told them that there were many complaints for the same issues online, they said they do not base their recalls on blogs and to fix the problem, I would have to incur the cost. This machine is the biggest piece of junk that I have ever owned. I will be sure not purchase a Whirlpool in the future!

Model #RF262LXSQ Serial #RT2031953 - I purchased this appliance from Lowes approximately 6 years ago. Last week, I was heating soup and about 5 minutes after I placed the pot on the stove on medium, I heard a large pop and then several cracking noises. When I entered my kitchen, I found the burner flaming red, and when I tried to remove the pot, it was stuck. I immediately turned the burner off and after a few minutes, when it began to cool, was able to remove the pot. What I found was the glass top had melted and blistered and was cracked from front to the back of the stove. Although Lowes was not able to help me, they suggested that I contact you as they had never heard of this happening before. Not only am I dissatisfied that a stove should last many years past this purchase, I am inconvenienced until another stove can be delivered. I believe this to be a factory malfunction of the stove and request a credit for my purchase.

We purchased the Top Loader Cabrio in 2006 for $1100. About 1 yr. later it just stopped, but was covered under a recall. A year later it stopped working again and cost $400 plus we bought a 3 yr. service contract for $350. A few months after the service contract ended, the spin cycle got very loud and it started leaking grease and water. It now need a ball bearing and $600 of work. So now we spent almost $2000 for this washer in 8 yrs. Our Maytag was $400 and lasted 15 yrs and we gave it to someone else who is still using it and we never had it repaired. It sounds like Cabrio customers have been complaining about the same issues for several years but they keep recurring and Whirlpool is doing nothing to correct them. We are not putting more money into it after reading all the complaints. We are buying another washer and another reliable brand. I would have been a customer for life because I did like the way it worked and cleaned, although I hear so many people had problems with that so I am not waiting for that to fail too. And I recommended the Cabrio to several people who bought them and now I hear they are starting to have problems. You should stand behind your product and correct these problems and recall or fix them at a reasonable cost.

Purchased this refrigerator in 7/2017. I cant stand it. Its pretty and works, but the NOISE!! I bought a white noise machine and placed it on the countertop next to the refrigerator just to drown out the noise (very high pitched sound). Repairmen came out twice. A part was replaced, but nothing changed. Said have to live with it. Dont buy Whirlpool or youll go crazy listening to this all day, especially with an open concept home. You can hear it everywhere!

I have had my washer & dryer about 12 yrs. It has given me great service; however the spin mechanism on the washer stopped one month ago. It was replaced thru my home appliance warranty. I need the front loader style because Im disabled now, and cant take clothes out of washer. My previous set was Kenmore & it lasted 20 years. Looking to purchase in 2 months.

My new refrigerator was purchased in December 2016. The black finish was scratched by the installers wiping off their hand prints. The retailer offered to replace the doors which happened two months later. The black finish scratched IMMEDIATELY while cleaning of the installers fingerprints, using a silk microfiber towel though it looks like the cleaning was done with steel wool pads. I called Whirlpool and the retailer. Whirlpool says to order more replacement doors. Ha! Ha! I have had black appliances since 2000 in another home and there was NEVER a problem cleaning them. I do not recommend WHIRLPOOL because of this problem with the stability of the black finish. I dont have a receipt or order number because the suite of appliances was purchased by the condo association, not me personally. But I can attest to the condition of the marred finish and the ludicrous solution provided by WHIRLPOOL customer service... order more doors. I guess youd have to do that every week after you clean the front of the refrigerator.

I currently rent, and so when our literally 30-yr. old GE dishwasher broke down, our landlords went out and installed us a new Whirlpool Dishwasher. I was excited because FINALLY I would have clean dishes and a dishwasher that didnt leak a bucket of water all over the floor. Well, weve had it for about 6-8 months now and I have to say that I am not impressed. It is not as great as I thought itd be. First of all, my dishes still look cloudy (despite using various brands - even homemade - detergent). Second, one out of every three washes gives me still-dirty dishes (food still on them, even though I rinse before loading the dishes). Now, Im not talking about tough stuck-on, need a jack-hammer to remove food. Just normal food. Mostly it is oil, like if I had a plate that I had eaten French fries on and there was grease left behind that normal rinsing didnt remove. A new dishwasher SHOULD be able to clean that! Third, it guzzles Jet Dry liquid (or whatever rinse aid you use) like an alcoholic in a bar. I have used a BIG bottle in one month. One month. With the old 30 yr. old dishwasher, it took me around 2 YEARS to use a big bottle. And lastly, it takes F-O-R-E-V-E-R to wash a load. My old dishwasher took an hour tops - to rinse, wash, rinse, and dry - and it was 30 years old. This new Whirlpool takes 3 HOURS!!! I can literally hand-wash all of my dishes (and with a family of 4 thats a lot of dirty dishes in one day), sit them out to air dry, and take a nap and it take LESS TIME than using the dishwasher. The dishwasher has all the bells and whistles to make it look good, but trust me, if I could have had the 30-year old dishwasher rebuilt to newness, I would have begged my landlord to do that instead. Dont waste your money on Whirlpool appliances. I left another less than friendly review for my Whirlpool Cabrio washer (only 5 years old), if you care to see it. Learned my lesson, dont buy Whirlpool. So disappointed because they used to be (USED TO BE) a reputable dependable brand.

This ref model # wrf736Sdam13 is less than 6 months old. The doors have never lined up. At the top is a 3/4 gap and it is 1/4 at the bottom. This is a side by side. Sometimes the left door will open on its own. If you stand to the side and look across the front, the left door sets out about 1/2. My wife and I have contacted whirlpool many times and they will not do anything. I am ready to get another ref and get what I can for this piece of JUNK. We built a new home and purchased all whirlpool appliances and do not like any of them. Will never buy whirlpool again. Very dissatisfied with all – RANGE, DISHWASHER AND THE VENT HOOD. PS, the vent hood sounds like it is crushing ice when you cut it on. Very, very DISSATISFIED with all of them.

We bought a Whirlpool dishwasher and microwave from a reputable appliance store. The dishwasher top basket broke within 30 days. The microwave lost 100% power within 30 days. Both under warranty but parts had to be ordered. Couldnt use either appliance for over a month. What is going on Whirlpool? We need a refrigerator, but I no longer trust your brand. I dont want it to quit and then lose all of our food! Please get it together and make quality products again.

I had this washer (WTW7990XGO) 5 years and finally had to replace it. It started with the touchscreen. No matter how often it was calibrated it was very frustrating to get it to respond. It would start dinging and going thru all the cycles at random times. Then there was the error code for the door lock. The door lock wasnt the problem, the surround was slightly warped and the door wasnt catching. Warped Im sure from having to literally climb into the machine to retrieve the clothes! Then a few months later it was another error code - the machine wasnt draining fast enough. It didnt drain at all. We had to use a water hose to drain it. After the second time with that, I went and bought a new washer - different brand, dials - no touch screen, and it has an agitator. Unfortunately, I ran into other customers in the appliance department who were having the same issues from 2 other brands of electronic washers. We all went back to as old school as was available.

Purchased this refrigerator, Model # WRS965CIAH on October 3, 2014. Paid extra for counter depth. Initially the refrigerator worked fine. After about 9 months we noticed the food in the back of the refrigerator especially on the top shelf started freezing. This started getting worse over the next 2 months. When I called Whirlpool 10/19/2015, 800-253-1301, I was told by their representative that this was normal, that air from the freezer blows into the refrigerator through vents and to just re-arrange my food so that it is not pushed to the back of the refrigerator. I asked him if this was normal why wasnt this happening in the first few months but only developed later? He had no answer. I asked him if it made sense if this was normal then everyone who buys this refrigerator has to make sure their food is not pushed to the back of the unit, then why dont they state that in the directions for use??? Ok everyone make sure every day you push all your food to the front of the unit so it doesnt freeze ridiculous. He just said thats the best thing to do. I asked him if I could talk to a technician, if maybe there was a way to fix it manually and he said there were no technicians there. I asked him if he knew about the lemon law and he said they dont have that there... ok. The refrigerator is just days after the 1 year purchase so he basically said just to call where I purchased it that Whirlpool could do nothing for me. Is this how Whirlpool trains their employees??? Good job Whirlpool, way to go. Luckily I purchased the extended warranty. Will see how the repair goes and report back. Did not call sooner due to health issues. Its not like the refrigerator is years old and started to break down - this is within a year. Whirlpool doesnt care about quality. Will never buy Whirlpool again and will spread the word as often as I can.

Absolute garbage!!! French door refrig/bottom freezer. Too much to go into. This is by far the worst product that I have EVER purchased in my life. If I was strong enough to lift this piece of ** over my head I would carry it into the corporate headquarters of these money grabbing dirt balls and throw it through the CEOs door. Amend that: I would locate customer service and consider them bowling pins. What a bummer; how far we have fallen!!!

While the washer is great, the reliability of the dryer is lacking. The timer has broken 3 times on ours in 3 years. Each time the cost of the switch is $75.00. Too much plastic on the shaft. If the plastic was removed, and the shaft was metal, it would be a definite improvement.

The electric Whirlpool double oven range seemed like a good choice for a single person. I bought it in 2016 around the same time I had some personal setbacks. After finding my emotional equilibrium I decided to return to my much loved baking. While I have no other complaints on this range the ovens are a problem for baking. The digital oven temperature readout doesnt reflect temperature fluctuations in the ovens. Once you enter your desired baking temp the readout never changes even after you open and close the oven door say to take out cookies. Given some of my poor results I suspect even when Im not opening and closing the oven door the temperature is not maintained. I was going to get an oven thermometer but the user manual says it wont reflect an accurate temperature due to way the elements cycle to provide a consistent temperature. Ha! If you want to bake this is not the range for you. My inconsistent results and too often wasted ingredients frustrate me no end.

I purchased the original Whirlpool refrigerator in August of 2013. That was replaced in October of 2013 due to a factory defect that left the ice maker unusable. In April of 2014, we now have a factory defect that has resulted in the entire unit unable to keep the fridge below 70 degrees F. It has been 2 weeks since the fridge died and Whirlpool has informed me it will be another 2 weeks until a replacement fridge will be delivered. I have spoken with countless customer service reps and 2 customer service managers, as well as 1 executive from the executive office in Michigan. Several times Whirlpool has dropped the ball in this process. The original repair appointments were booked and had to be rebooked because the repair company could not accommodate the appointment times Whirlpool booked. It took over a week to get the fridge declared dead. Then another week just to process the request through tech support... After speaking with 2 customer service managers and being told it was being rushed, I spoke with an executive who said the claim had never been submitted and it would take another 24 to 48 hours to process. I spoke with the executive after the 48 hours and he said the fridge will be delivered in 2 weeks! 4 weeks without refrigeration for a second factory defect. I have explained that I have a newborn (6 weeks old when this started) and a 2 year old, and we have had up to 9 people staying in the house (to visit with the baby) over this period and that I need a fridge to keep my breast milk cold. I was told I would receive a $75 gift card and a $125 check to help with food and costs associated with the loss of our fridge... Neither have arrived. We are spending quite a bit on ice just to be able to keep food and milk cold to temp. so we dont have to spend money on eating out (too expensive for us). I am shocked by Whirlpool’s poor customer service. The first time the fridge was replaced I dealt with one person and didnt have to call the customer service line every day. I wish I had her number still.

I purchased the Whirlpool Cabrio washer and dryer in 2007. They have been the biggest pieces of junk. One year after my purchase, the water pump broke and had to be replaced for $100 and that is with my husband doing it. Then the dryer broke twice. Now, the washer is not spinning. He took it apart and I purchased $80 in parts. It still doesnt spin. He thinks the motor went and it gives a p50 code. This washer does make holes in your clothes. So many of my summer tops were ruined because of this washer. A friend has the same washer and she started getting the holes in the clothes, so that is how we figured it out. Today, I went and picked up a washer at my rental home, a GE that is 10 years old. My clothes never felt cleaner and it runs like a charm. That Cabrio always smelled like mildew because it seemed like all the water didnt drain out of it and it would sit in the bottom. What a shame. Its only 6 years old and I paid $800 for it and for parts. My husband cant wait to put it on the curb on garbage day. My friend warrantied hers and when the guy couldnt fix the problem, they gave her partial money back. At least she got something. These should be recalled and we should get partial money back depending on how old it is. I will tell everyone not buy these. They are the biggest pieces of junk!

We purchased our Whirlpool Refrigerator #WRT519SZDB from the Home Depot 2 years and 10 Months ago. About three weeks ago it started to freeze items in the frig section. We lowered the frig section cooling level one selection and went on a two week vacation. When we came back, everything in the freezer section was thawed out. We had a tech look at it and he told us that the compressor was partly seized and overheating. Tried to reach someone at Whirlpool customer service by phone, email, and chat but so far, I have not had anyone contact Me back? Looks like repair will cost almost as much as a replacement refrigerator. So much for Whirlpool being a trusted brand!

We purchased the Whirlpool washer less than a year ago and are now having the 4th transmission put into it. We are also having the 3rd timer put into it. We purchased this from Sears and bought the extended warranty (thank God). One of the times the technician ordered the parts to repair the machine. The service center sent the wrong parts and we had to wait an additional week for the correct parts to arrive. The 3rd transmission they installed lasted a week before it leaked gear oil all over our floor. When you do get a service call scheduled it will get rescheduled to a later date. This happened twice. They also cancelled the service call once before they fixed the machine. If I could give a zero star for this I would. DO YOURSELF A FAVOR AND DO NOT BUY A WHIRLPOOL WASHER AND DO NOT I REPEAT DO NOT GO TO SEARS FOR ANYTHING. Worst company to business with. I will say this that the service guy that comes out to do the work is a good guy. He stayed until almost 9:00 pm on one of the service calls. Hes been here so many times our dog knows him and doesnt bark at him anymore.

Our new Whirlpool Side-by-Side Refrigerator is very versatile as it serves the needs of a busy, family kitchen. It is heavily used storing cold foodstuffs to feed our family of four, plus two active grandsons. Being able to re-configure the shelving space enables us to adjust the main compartment accommodating items of different sizes (think a thawing turkey or a 24-can case of soft drinks!) to ensure our most functional usage. The same can be said of its freezer space - it too features built-in slots to reposition shelving for varied size packages and boxes. Convenient in-door water and ice dispensers round out the beneficial features of this attractive appliance.

I took the Sears salesmans suggestion and bought a high-end quiet dishwasher. It worked wonderfully until it sprung a major leak. Computer told me the phone # to call. It took a week for the Sears repairman to come out and $79 fee to just look at it. He said the fitting between the sump and the pump came off and flooded water over the electric motor. Electric motor is shot! Cost to repair is over $400 and a 3-week wait!!! When and if a new motor is installed, only then do we know if the computer is also fried. This was a high-end dishwasher. Factory warranty just ran out. Repairman said this is a common problem with this model. DO NOT BUY THIS MODEL.

I purchased a side by side Whirlpool refrigerator in December 2009. In one year’s time, all of the plastic shelving has completely broken. The repair man said that he felt like the plastic was substandard and to call Whirlpool but they said that we must have abused the shelving.I and my husband are senior citizens and the only ones using this refrigerator. How can all the plastic components break within one year? I had my last refrigerator for over 10 years and I gave it to my son. It is still running and all the plastic shelving is still intact.I feel Whirlpool should fix this problem but they do not care about their customers. Once they have your money, you are forgotten. In the end, they will be forgotten because I advise everyone I know not to buy from Whirlpool.

How can Whirlpool deliver a new refrigerator/freezer and refuse to include a shelf in the freezer even though there are rails built in on the sidewalls to support a shelf??? Of course they will sell me one. The cheapness of todays manufacturers is appalling especially in light of the prices they charge.

On 12/27/2013 I bought a Whirlpool hot water heater from Lowes Model NU50T122-403. On 12-13-2015 the pilot went out. When I called tech support on 12-14-2015 they gave number what were call centers or person who returned the calls. So I called a local plumber that I used before. He came out and told me that had to replace the pilot. On the 16th 2015 of Dec. that did not work and told us the heater needed to be replaced. The replacement will happen today I hope with little to no help from Whirlpool. I would advise you to do your homework before you buy a Whirlpool hot water heater.

I purchased the four-door Whirlpool stainless steel refrigerator. It was installed on the 15th of June. One month later, the ice was not coming through the dispenser and if it did, it was a small amount. During this time, I was receiving notices from them about purchasing an extended warranty. Today, August 23, 2012, the ice maker stopped working completely. I was disgusted. Paying for the top-of-the-line refrigerator that doesnt last for 90 days is ridiculous. Also, the handle on the vegetable keeps coming off. That will be the last Whirlpool appliance I will buy.

I found this site while looking for a part number for the thermocouple. Lowes had one, but not for the FG model. I decided to call the number on here from Chris to see where I could buy the correct one with left-handed threads. I was told that they would sell me the conversion kit, but I couldnt get just the $8 thermocouple. Then $47.90 later and the conversion kit is on its way. Im not happy about it but at least I got 6 years out of my water heater before the thermocouple failed. The plus side is next time, I can get the $8 part from Lowes and not be without hot water for a week.

We purchased our Whirlpool Refrigerator, oven, and microwave a little more than a year ago. Not a single negative event with any of these products and my wife and I wholeheartedly recommend Whirlpool for operation and last ability, unlike the products we replaced them with.

We bought all Whirlpool Gold Appliances when we re-did our kitchen 5 years ago -- fridge, d. washer, oven, glass top stove, and microwave. Recently I noticed a pool of water in front of the fridge. Turns out there is a sticky grommet problem that prevents moisture from draining into a pan on the inside back bottom of the fridge. Whirlpool will send you a replacement part that is totally different than the original poor design (a long hose affair) BUT wont pay for the labor to put it in unless the unit is less than 2 years old.I watched a video showing how to do it, but it looks pretty tricky and involved plus risky because you can break the drain pan in the process. Spoke with a Whirlpool rep and a supervisor -- both admitted to a quality problem but got nowhere on the labor. Theyre sending the part, and the supervisors supervisor is supposed to give me a call, so well see if they eventually do the right thing and cover the labor. I mean cmon... the parts obvious a bad design, or they wouldnt be sending a totally redesigned part! Covering the labor only if its two years old or less? Even the Whirlpool techs online are saying the problem happens after about 4 years! The grommet gets sticky and wont drain due to heat from the compressor, and that takes time to happen. Ill update this when I hear back from Whirlpool.

Two-year old Whirlpool Cabrio top load washer; absolute piece of junk! Bearing on the drum howls like a train. Now the master board or some other sensor (under drum) is out. Serviced for the third time and the service repairman states its cheaper to replace than to repair. For a 2 person household, it is reasonable for us to expect more than 2 years from a washing machine. Same experience with Whirlpool 15 years ago. 1st time shame on you; second time shame on me.

Whirlpool - Back in the 1980s we had Whirlpool appliances that lasted for many, many years. We are now in our mid 60s and retired. We purchased a new home 2-1/2 years ago. Whirlpool appliances were provided with our new home. We were quite pleased at the time. However, we are now sorry we have them.We are very easy on everything we own. When we replace appliances, cars, furniture, etc. we are generally able to sell our used items, which are always in great condition. Unfortunately, this is not the case with our current appliances. I will list the many problems.Combo range hood/microwave oven: it vented absolutely nothing. The microwave oven had its own set of just plain silly issues with the manner in which the touchpad had to be set. The oven did at least work. 2/2013 we had a Broan range hood installed and vented to the outside and purchased a Whirlpool countertop microwave oven. Again we had the little issues with using the touchpad plus the door was very hard to open. This countertop microwave oven failed 1/2015, less than a year of usage. At this time we purchased a Panasonic microwave that is much simpler to use.The Smooth-top range/oven looks nice. It is the most inconsistent range/oven we have ever owned. You cannot lower the cooktop burners to simmer. There is no simmer. On that setting it may as well be turned off. I can set it at about 9 oclock on the dial and some days that may be simmer. Others days it could be higher. Overall, the burners have no consistency. The oven cools quickly and I must be mindful not to toss in a 2nd sheet of cookies without checking the temperature. I have never had to do this on any other oven we have owned.The dishwasher does clean my dishes, thank goodness. However, I have had 2 service calls (under warranty) for a little gasket (hinge pad) which keeps the door propped a bit while loading the silverware into the basket. This piece has failed a third time I will just live without being able to prop the door. And then there is the silverware basket. Each piece must be loaded, handle first, into the slots on the basket. Of course, some of my silverware has wider handles so this does not work well. Such a poor design.The refrigerator was my pride and joy. We paid the extra charge for the French door style instead of the side-by-side style that came with the house. My charges here are more serious. 2 of the little door shelves have broken. Oddly enough these are small shelves which have some items on them that are not used often. If I choose to replace them, it will cost me over 25.00 for each of these little gems. Now, a piece of plastic on the veggie drawer has broken so I must be mindful not to let the drawer drop.Worst of all was the last service call out of warranty. I had standing water/ice on the floor of the freezer. Apparently this was due to a poor design and my service man replaced it with a new P-Trap that actually works. Yes, the original design was bad, yet I still had to pay for the replacement. Seems like this should have been a recall and replaced free of charge. Instead my total charge was 144.06. UGH!!! Now, I do understand I was likely provided bottom of the line appliances with my new home, but to have issues with all of them is ridiculous.

I had my old agitating washer for 8 yrs that went out. I liked Whirlpool so decide to try their washer. Found the Cabrio washer (SWS5000WO) and thought without the agitator it would give me more room for clothes to wash better. Boy was I wrong, no matter what cycle or what size load it is off balance on the very first spin. I have to stay near by to stop the washer before the first spin adjust the load and start over again. Jeans and towels are impossible to clean. It throws the tub so bad it has pushed the side out. I have checked the balancing rods and they are fine. After reading other complaints realize the Cabrio washers are terrible. I will be looking for a refurbished washer with an agitator and doubt I will buy Whirlpool again. They should have a recall on these machines. They are terrible.

Do not buy anything from Whirlpool. This company needs forced out of business. Everything breaks down within weeks or months. I bought a fridge, dishwasher, and a washer dryer. Within 16 months they all went to the trash.

Im very frustrated. I bought a Whirlpool Refrigerator for nearly $1300 in Sept. 11. It is a side-by-side Model #ED5KVEXVL00. The refrigerator side started warming up to the point that we noticed. We put a thermometer inside to confirm; it went up to nearly 60 degrees. We tried cleaning any dust underneath from the coils and even unplugged it for a while. The compressor appears to be the potential problem. Sears is not sending a repair guy for 2 WEEKS (It is a hot July here in NY)!!!!We are saddened that Whirlpool says it is out of the one-year warranty - so now we are facing the choice of a large repair bill or buying a new refrigerator. What a waste of money... Its not even 2 years and it needs service or a dumpster. Shame on Whirlpool for not standing up for customers when clearly there is something wrong with this machine so close to the warranty and so new. Sears and Whirlpool - youve lost me as a future appliance customer!!! :(

Please do yourself a favor and stay away from both Whirlpool and this unit. I purchased it from a local dealership and paid $881.00 which included tax and delivery cost. In less than 2 years, it broke. Whirlpool does not offer a warranty on the unit. After having a Whirlpool repair person come out for a cost of $75.00, I was informed that the parts to replace would cost $800.00 not counting additional labor cost which was TBD. I contacted Whirlpool and went from Agent (Phylicia) to supervisor (Ashley) to Manager (Carol **). The best offer I was given was to buy the parts at a discount of $400.00 which did not include tax, delivery or labor. So it would have run approx. $550.00 to over $600.00 to fix a $771.00 washer.My next letter is to Jeff Fettig (553 Benson Rd, Benton Harbor, MI 49022/ CIO of Whirlpool) to let him know how impressed I am with his product and customer service support. The next Whirlpool item I buy will be never. Take this as a word of warning to go Maytag or any other vendor because Whirlpool will not support you once the sale has been completed. Good Luck.

First one had major problems. The bladder they call it. They took out the whole system out, replaced the tube that goes to the top of the refrigerator which is where it always starts leaking so they worked on it three times, junked it, gave me a new one and here I am again same thing. Ruined my hardwood floor and Im stuck with it. Never again will I buy WHIRLPOOL.

The dishwasher is quiet and seems to clean most all of the dishes even when there is dried on food remnants. Multiple cycles that allow for light, medium and heavy cleaning. Also the ability for air dry and minimum use of water. The size is appropriate for normal amount of dishes, pots, pans, etc. Stainless steel front with most of the controls hidden. I have always had good luck with Whirlpool products, with this dishwasher continuing with being a quality product for the amount of money spent.

On its 1st year, the water pump went out. It cost $200.00 to replace it. On its 2nd year, the circuit board went out, and it took $300.00+ to replace it. On its 5th year, the bearings went out and cost $250.00 to replace it. I bought this for $900.00, and I already have paid $750.00 plus the price of purchase which makes this washer $1,600.00. Whirlpool should compensate all of us who have worked hard and have purchased this product! I will never purchase from Whirlpool again. I can’t afford them. I should get a refund from Whirlpool. Don’t they care? Email me for these problems at **. I am so dissatisfied with this product.

I purchased 5 Whirlpool appliances when I moved into a new home approximately 5 years ago. The selection buttons on the plastic panels on the front of 3 (dishwasher, washer and dryer) out of the 5 appliances has either broken completely through or are in the process of breaking through, leaving an ugly appearance on the front of the appliances. When inquiring if I could replace these panels, I was told that one (dishwasher) would cost me $100.00. I believe that the structure of these panels has been extremely poorly manufactured. Why would you put perforation around each button? It is obvious that they would push through. What can Whirlpool do for me?

Special features eg changing HE detergent conc. ratio for auto add feature in Load and Go is impossible to find, extra rinse doesnt work. No extra spin which would be useful for bulky loads. But preset cycles work fine and machine has very low vibration a big plus.

I have called Whirlpool multiple times because our washing machine model #WFW9290FW has been out of service for 5 weeks now. I have been informed that I need part #W10604640, which is on back-order and they wont give me any idea of how long it is going to take to get this part replaced. Apparently, there are 96 total people who also need this part. I find it hard to believe that a company this big would not have this part on hand and they would not have any idea how long it would take to get it replaced. I asked them to give me a new washing machine for free to replace it because of the poor service and the unreliable washing machine. They told me they could give me another washing machine at 40% off, but based on the lack of follow-up and the amount of time that has passed since my initial call, I dont want another Whirlpool product. This is the worst customer service ever.

Whirlpool gold bottom freezer is 2 years old. This model has a design flaw. And due to this the drain is frozen in the bottom of the freezer. Water is leaking onto the floor. I called for service and whirlpool is charging me. To fix a problem that is their fault. This is unfair.

I purchased a home that came with Whirlpool appliances. I begged the company for GE or Maytag. Of course they went with the cheapest they could find. I must admit the microwave gets very hot but the dishwasher is a piece of crap! The water doesnt get hot and the dryer doesnt work. They tried to tell me it NEEDED Jet-Dry. I own 4 homes and have lived in all of them. Ive NEVER used Jet-Dry and all the others work perfectly. Run as far as you can from Whirlpool!

We bought a Whirlpool dishwasher when we learned that my daughter and two children would be living with us for an extended time. We bought it a couple of months before they came. During that time I used it maybe four or five times as there are only two of us and didnt need to use it. Since they arrived in early June, the dishwasher malfunctioned almost immediately. Talking with their representative was useless and frustrating. The only words she seemed to know were circuit breaker. That is where the conversation started and ended despite my assurances that it had nothing to do with a circuit breaker. We wrangled round and round to no avail. This company used to be an American standard. Now it is a class A maker of junk.

In June of 2010, I purchased a new Whirlpool Estate EED4400WQ0 dryer (serial number M01156261) with an accompanying washing machine. It has been in a clean, climate-controlled environment and gently used by my family of four for just short of two years. Last week, I began to notice that the clothes coming out of the dryer were cool and damp and it quickly became apparent that the dryer was only heating intermittently. This morning, the service person from the dealer who sold me the washer and dryer set (and a Whirlpool dishwasher a few months later) told me that contacts on the timer unit were bad and that the entire switch would have to be replaced. This is no small portion of the machine and the part alone will cost me about $150. After labor, we are looking at an expense of approximately half of the original cost of the machine - in less than two years. I called the Whirlpool’s customer service line to ask if there was anything that could be done and the answer was: Sorry, we cant do anything for you.” It is not acceptable to me for an appliance to become that expensive that fast. If Whirlpool cant do anything for me about this, then I will not be purchasing anymore Whirlpool products.

Have dishwasher wdf530plyw6 less than three years. Will only run on 1 hour cycle. No other wash option works. Called company, wont fix, offer other warranty plan. Utensil holder broke early on.

I bought the Whirlpool Cabrio topload washer (WTW7800XW2) in April 2011. In May 2012, I noticed the door was broken on both sides. It has now popped up and is broken so bad that it can barely be used without replacing it. I called Lowes, where it was purchased, to quickly be told that there was nothing they could do because it is out of the years warranty. This is just such a copy out to have an excuse, so that they would not even offer any assistance. Also, I paid $2,000.00 for the set; I bought the dryer as well. I just could not imagine an expensive machine like this having such a problem. Prior to buying this machine, I had my washer for 10 years. It has no problem; it was just time to buy a newer model, so I thought!After the store (Lowes) would not help, I decided to call Whirlpool; and the woman I spoke with was even less help. Andrea said there was nothing they could do since it was outside the year of manufacturers warranty. She seemed glad to have this as an excuse. I told her this is too much money to have something like this to happen. I told her it is obvious the door was defective. She said again sorry but that theres nothing she could do. She did offer to sell me a warranty for a year for $327.52. This was too expensive. I asked her what else could she do, and she told me nothing. I asked how much the door was, and she told me $212.00. I feel like I have been royally and deliberately ripped off, and Whirlpool knows it. I say to anyone reading this to please be aware if you are purchasing this product. You will most likely be sorry you invested all this money for it. You will get a companys brand that does not care and will not stand by their product.

DO NOT purchase a WHIRLPOOL hot water heater!! The gas valve temperature sensors on these units are faulty. Our technician has replaced several of these defective sensors. Costs $250.00 to install - water tank is only a year old! WHIRLPOOL REFUSES TO ACKNOWLEDGE THIS PROBLEM!! We bought this particular unit because of the reputable name brand. They dont live up to expectations. Dont waste your money on a Whirlpool - youll be replacing it soon! Very disappointed in this company!

I have the stainless steel Whirlpool Gold appliances. They look beautiful but do not work for long. For one, the dual burner never heated properly on the cooktop. I just worked around it. The oven vent on the cooktop left brown marks on the stainless facade attic top by the clock. Ive read some have melted this area. Then after 2 years, the entire front glass door and handle fell off when I opened it. It not only fell, but the cheap plastic lip that holds the door on cracked so it is impossible to get back on. So, since I cant afford a new stove. Im stuck with this horrible looking mess in my kitchen.

I bought this to provide A/C to our bedroom during a power outage by use of our Gasoline generator. It is very quiet and provide a very cool air flow. The double vent pipes make it efficient and more than capable of cooling out 15 X 25 foor bedroom. Whirlpool has 28,000 employees in the USA.

I have a new Whirlpool double convection oven which is very noisy. There is a rattle and pinging noise that occurs and the fan is also loud. Im not sure if it is an install or product issue. Can anyone comment on their convection oven? I dont believe this is normal. I am disappointed with my purchase and would opt for gas or basic electric. The double convection ovens were fairly pricey too.

In October 2009, we purchased a Whirlpool Cabrio topload washing machine for almost $900, because my wifes sister had a 1-year-old one and had been pleased. The Cabrio replaced a 3 1/2-year-old Maytag that died with a seized-up transmission. Maytag is also a Whirlpool product for those of you who do not know. We had issues at first with it going off balance but dealt with it. It was also taking 40+ minutes to do even a small load of laundry, but again, we dealt with it. Fast forward about 3 years, and we notice the machine is making really loud sounds during the spin cycle. I checked for any obvious issues but found none. The noise kept getting louder with each use. Finally, I called a repairman to check it out. His diagnosis was quick. The bearings were going bad in the machine, and he said it would eventually fail. He quoted me a price of between $400-$500 to repair because the job is very labor-intensive. I declined the repair but still had to pay him a trip charge. Then I checked with my wifes sister about hers, and she said hers had been making a very loud sound for several months but they were just ignoring it. I told her about the diagnosis of mine and advised her to tilt the machine back to look under it. Sure enough, there were oil stains under her machine, just like mine, indicating the bearings were failing. So we have 2 Cabrio machines, one 3 years old and the other 4 years old with the exact same problem. I called Whirlpool since I had registered the machine when I purchased it. They basically told me to go fly a kite since I had not purchased the extended warranty. They said I could attempt to repair it myself to save money, but they advised to have their repairman do the work. Well, no kidding. What a joke. They expect you to buy a $900 machine and have to replace it every 3 years. I am done with Whirlpool products. FYI, Kenmore products are also made by Whirlpool, so Sears is not an option. My wifes sister and we bought new GE washing machines, and both of us purchased the extended warranty this time. For $129 (5 years), its cheap, peace of mind. Whirlpool is crap. I would suggest never buying any of their products. I know we never will. Once they have your money, they dont care.

We relied on consumer reports as the primary source for a recommendation on this washer. Just under two years old, it started making a noise, which suddenly went away. Then one day the machine would not spin and drain, and we could not decipher the error code into anything useful. I turned the machine over to find that the drive belt was half-on/half off the pulley on the drive motor. This caused the belt to ride against the belt guard and wear right through it. I removed the belt and determined that the cause of the problem was that the large pulley on the drum was loose. For some reason the nut which holds that pulley on was slightly loose, causing the pulley to wobble. Not sure why they didnt use some Loctite on that nut. I put everything back together and tightened the nut. No problems and I checked it a month later, everything was still good. Fast forward to last week, when the machine was not yet 3 years old. Same thing, washer would not spin and drain. Tipped machine over to find that the belt had fallen off, the drum pulley was again loose. But this time the belt had damaged the pulley on the motor. I figured, no problem, just order a new pulley. Well you can buy just the pulley on the drum, but the pulley on the motor is part of the motor, it cannot be ordered by itself. The cheapest I could find the motor online was $250. We decided to cut our losses and buy a new machine. We will NEVER buy another Whirlpool appliance (or anyone elses by the same manufacturer, i.e. Maytag). Our last Kenmore washer lasted 23 years. Oh but it had an agitator and wasnt listed as HE (High Efficiency), so I suppose the environmentalists would get the dry heaves thinking about the impact of that washer on the environment. But it was useful for 23 years. Now this High Efficiency Whirlpool is headed for the recycling pile. Sorry, I think this hurts the environment more than an appliance which just works year after year. Yep, they took a design that worked and now we have energy/water efficient washers that dont last very long and are so expensive to repair that the solution is to just buy a new one.

Im a renter, and I know the landlord purchased the least expensive stove for this apartment, but that shouldnt mean one has to absorb ongoing off-gassing fumes for well over a month now. The stove was installed 2-18-17, and its now 4-6-17, still havent been able to use it. Is this really off-gassing or is this what Americans have to contend with now! Oh and theres the little sticker that says Made in America and in small print it says designed and assembled in America, but no mention as to where the parts came from!!! The only reason Im giving even a One Star rating is because I cant continue through this review without at least marking one star.

We purchased a Whirlpool Cabrio Washer (Mod #WTW7300XW1) and Dryer in 2011. Ever since we have had the washer it has eaten clothing, towels, sheets etc. It now has a main bearing that is so noisy that we have to close the door to the laundry room to be able to hear in the rest of the house. Also the sealed tank around the drum is now leaking. We invested close to $1000.00 in this washer and in my opinion it is a piece of junk. The washer repairman told me that he has had 3 (three) other Cabrios with the same problem in the last month, but Whirlpool says that there is nothing they can do as they have had no issues with this problem. Last Whirlpool product that I will buy.

Reliability. I have bought Whirlpool used and new and they have been the best washers that last so much longer than other brands. They also have more than enough settings to truly take care of everything in your home that can be washed.

Purchase a brand new Whirlpool fridge at the Fry’s Electronic in 2017. Broke down in 2018 almost 1 year after. Called Whirlpool company for replacing a new one. They didn’t replace before they had sent out a certified technician for fixing 3 times. It took forever to fix it, and still had the same problem after months. Finally, they agreed to replace a new one. Now I still have the same problem with a newer one which they replaced it over a year ago (including fixing and placing time). Just called to the Whirlpool company today for fixing or replacing, spoke to rep Sara, she said that it’s no longer under warranty because it’s more than 1 year. I told her that because the company didn’t replace right away; therefore, it has been more than 1 year; but from the time they replaced it, it hasn’t been 1 year. Ill never buy any Whirlpool products again.

I bought a new Whirlpool refrigerator from Sears and within a month the refrigerator side did not maintain temperature where milk would not spoil... Cool but never cold. I called Sears and they said its Whirlpool warranty to contact them. This I did and about a week later they contacted a local service company they use to maintain their equipment... Long story short this will be the 4th time they were informed the refrigerator still doesnt maintain temperature... Food had to be thrown out because of that.I asked them to refund me my cost or at minimum get a working refrigerator to me because after 4 attempts at trying to fix the problem it still exists... They just want to keep sending a repairman out there who still cant figure out the problem and that has cost me much time away from work not the mention the spoiled food costs... Even when complaining my dilemma to the repairman he said, All they will do is keep calling us and kick the can down the road... They could care less about what it has cost me in time and money... I had to give 1 star to this company but they dont deserve even that one... Dont waste you time thinking a warranty by them is worth a flip and now over 3 months Im without a refrigerator...

We bought a new Whirlpool refrigerator about three years ago. Because of space, we had to purchase one with a top freezer and also with no ice maker. First of all we didnt realize it was much deeper than our old Kenmore so it stuck out further into the kitchen space. That was not that big of an issue. At first everything ran great including the top freezer compartment, or so we thought. Then we noticed that when we had ice cream in the freezer and put water in ice cube trays to freeze, the ice cream would get very very soft. This continued to the point that now anytime I put water in there to freeze ice cubes I have to turn up the temperature to keep the ice cream frozen. Once the ice cubes are froze, there is no problem, but they take at least six hours to freeze. Then one day when a young child slammed the refrigerator door closed, the freezer door popped open about an eighth of an inch and then closed again. So, I tried it. Anytime you close the refrigerator door a little too hard the freezer door pops open. I then tried the dollar bill test to check the strength of the seal. The bill pulled right out of the door with very little effort. So, is the problem bad seals, bad design, or bad quality control, or what. How can I be assured that the frozen foods in the freezer are being frozen as solid as they should be. I know they dont freeze solid enough in the freezer door. I will eventually dump this refrigerator and go get another Frigidaire. If we have to get one with a bottom freezer, we will just have to rearrange our kitchen to accommodate it. But, having to turn the temp up and down every day is ridiculous. I have had issues with food close to the walls in all refrigerators slightly freeze, but never had an issue with keeping things cold enough. I will never buy another Whirlpool refrigerator, stove, or anything else for that matter. I have always had good luck with Frigidaire, so I will stick with what I know works.

17 month old Whirlpool duet washer door lock broke. ($300) repair! Had given my old (13 years) set to daughter when I moved. That set has never had a repair or problem! Why do they keep making things with more bells and whistles we dont need and so cheaply made? Frustrated, annoyed and becoming cynical in middle age.

Purchased this washer in 2009 from Lowes, believing the hype that it was efficient. Since we only needed a Washer at the time, we overpaid (it is more cost effective when you buy both washer and dryer). So we paid $1000.00 for this machine (we purchased the stand as well). After the 1st year, there seemed to be a significant decrease in how fast the washer spun, as the clothes were coming out wetter. I didnt pay much attention, but 2 years later, the machine has a weird problem where it couldnt complete the cycle, and by this time, every time it Spun, the noise was louder and louder.I contact Whirlpool, placed a service call and the Technician came out. $225.00 later, there was a hose that was pinched that was sending a wrong signal to the washer. He fixed that and told me I should get a contract on the machine through Whirlpool since I seemed to be having problems. I purchased the contract, for $300.00, and 2 1/2 weeks later placed another service call, as the noise from the machine was happening every time I did laundry. The service guy came out, indicated that it seemed to be the Agitator, and that he would need to order parts, and that they had a SPECIALIST who only does this type of repair, since they have many! He also indicated that the hose may have crimped due to the movement of the entire agitator!Well, after not hearing from ANYONE for 2 weeks, I called the repair company who told me WHIRLPOOL was supposed to call and let me know that they would NOT fix the machine, as the parts cost more than the Washer, which is now valued at $500.00! No one from WHIRLPOOL EVER CALLED, and I cant understand how a $1000.00 Washing machine touted to be so efficient and environmentally friendly has been THROWN OUT after 3 years!!! And now I am out the $225.00 repair, have no washing machine, $1000.00 down the drain (and I forgot to mention a year later we bought the matching WHIRLPOOL DRYER and OVERPAID) and now have to purchase another machine, which I assure you WONT BE WHIRLPOOL! As most of us have experienced, WASHING MACHINES last for many years! The washer I had before this was over 20 years!!!! So much for efficient and environmentally friendly... The only thing GREEN about this machine is how much of my $$$ has gone to Whirlpool!

I bought a Whirpool side by side model GSF26C5EXW00 on 4/24 from Lowes in Buford, It was delivered the next day.We followed all the start up directions. You know what a mildewy moldy towel smells like...Well that is what the water and ice smells and taste like coming out of the dispenser. I have had the technician to my house 6 times. the tap water taste good, the water coming out of the line leading to the refrigerator is good. Gee is must be something in the refrigerator! How many times do they have to come out before they actually do something about it? Like replace it or give me my money back.

Our Whirlpool Duet front loader washer developed a mildew smell and started making a horrible banging noise on the spin cycle. We had a service man come out and the concrete weight had broken in half. He said this was not uncommon. I just did a Google search and apparently this is a true factory defect. Luckily we had purchased an extended warranty. I always thought Whirlpool was a premium brand but after this experience I will never buy another washer from them. They should do a product recall.

In 2015 door of top loading washer (Whirlpool Cabrio Washer) needed total replacement. Lucky I had an extended warranty. 2018 March, extended warranty expired and now have the exact same problem. Pretty crummy product if major part like a door has to be replaced every 3-4 years. We do not wash large items like blankets/quilts in this machine. That goes to a laundromat where there are oversized machines or to a dry cleaner. So the only reason for this breakage is a default in the lid assembly. There is only one phone number for customer service, repair, parts etc. Put in my service call and filed a complaint at same time hoping for at least a small discount. Ha! $100 plus tax for service call- part price ranges from $150-230 plus tax. Whirlpool could tell me the part exists but would not say how long it takes to get it! Do NOT buy Whirlpool washer with top load lid that has glass window. Big problem is that Whirlpool now has Jenn-Air, KitchenAid, Maytag and Amana all under their umbrella.

Whirlpool Dishwasher purchased at ABC Warehouse in Chesterfield, MI and was delivered on 10-2-2014, and one year later, we noticed that the tips of the lower basket were coming off. We contacted the holder of the extended warranty (5-yr.) and also Whirlpool. Both replied the fault was cosmetic and was not covered by warranty, that only mechanical/electrical components were covered. When we were buying the extended warranty, we were told that we were covered for all issues that may occur. We werent told cosmetic flaws were not covered. I guess consumers should, before buying a new product, make a specific list of possible problems, and make sure whats covered and not covered. We have been unable to resolve this issue.

I hope this review makes it to the president of Whirlpool! My husband and I built our first home and finally moved into it on April 22, 2017. We saved everywhere we could and I did my best to research my appliances. I was so excited to buy a BIG refrigerator for our family of five, (3 are hungry teenagers!) after years of using a smaller side-by-side. We went with the 31.5-cu ft French door/drawer with dual icemakers, model #WRF993FIFM. The original price was $3,599 but we got it on sale for $2,298 at Home Depot. After only 5 months it stopped cooling! I woke up one morning to find a fridge full of spoiled food!! After waiting 3 weeks I had 2 different repairmen come out and have been told that it is un-repairable due to two parts that are needed, one of which is on back order indefinitely. Ive called Whirlpool numerous times and only get the run around and Im sorry mam we cant do anything else. So Im just supposed to be without my refrigerator until who knows when?! The first 2 weeks of this crap we had to live out of Igloo coolers on our back porch. That meant no buying real groceries, only milk and juice and drinks. Thankfully the awesome people at Home Depot brought us a loaner, which is an apartment size fridge, to use while we wait. So now I just have to walk across the house to my garage every time I need something, and I cant buy much food because it wont fit!! Im so disgusted with how Whirlpool is handling this!!! Not only did we buy our fridge but we also went with Whirlpool for our stove, dishwasher and microwave, and we already owned a newer Whirlpool washer and dryer set. We spent thousands of dollars and cant even get them to exchange this piece of junk! Come on Whirlpool, surely you dont treat all your customers this way!? Do the right thing and let us have a replacement!!!

This is Whirlpool model MVWP835DC2. I bought brand new. Recently used about once a week. Got an alarm that indicated no communication to core unit. Talked to Whirlpool service and unit is out of warranty (20 months) and advised I should use authorized service company to come and diagnose. This took 2 weeks. Service man came, washer did not power up. He quoted that repairs would be $750 and not worth it, buy a new one. I went on internet and found YouTube videos that showed how to diagnose and fix. I called Whirlpool for new console, $350 and one month. Went to parts house and got part for $250. This fixed problem.I have a few problems with this machine and company. 1) This now turns out to be a known problem with these machines. The console fails. I am not sure how this is going to last 30 years. 2) Service man took nothing apart and could not diagnose problem with no power. He quoted $350 for the console and the balance for the core. He was guessing or pulling a scam. Take your choice.3) Part not available from Whirlpool because so many are failing.Thanks for making a great product.

This washing machine is a piece of junk. It broke down exactly 2 days after the one year warranty expired. Home Depot said there was nothing they could do and Whirlpool said the same thing. This washing machine was not used on a weekly basis. It perhaps washed 20 loads during the course of the year. I had many issues with the sensors before it broke down completely. Sometimes, half the clothes would be dry after the entire cycle. I was so angry that I had a local independent contractor come in and look at it. He said the motor was broken and needed to be replaced. So much for $700 down the drain. I will never buy a Whirlpool product again. This was the worst experience Ive ever had with an appliance.

Had washer less than 1 year and washer stopped and was flashing code F 51. Called Whirlpool and they sent a repair person. He worked on it and didnt fix problem. Called Whirlpool back. They had to order parts. Repairman came back - replaced parts. Now not 6 months later same thing happening. Whirlpool said we have to pay for labor to repair again. We went online after this happened the first time and saw where others had same problem - this washer should be recalled. The repairman said this part was corroding. This should not be happening on a new washer. We will never buy another Whirlpool product again!!!! Im concerned that it will keep repeating over and over and we paid 700+ for this washer not 1 1/2 ago. My last washer lasted 15 years!!! Wasnt a Whirlpool!!!

This Whirlpool is great with a side by side refrigerator and freezer. I love the ice maker and water on the freezer side door. The refrigerator keeps my veggies and fruit fresh and crisp. Has a water filter purification that makes the water taste like mountain spring water.

[Model WTW6300WW0, Type 580] A few years ago Whirlpool goofed - they left out the Perma-press cycle on a high-efficiency washing machine model.We noticed the absence of Perma-press (or Casual as it sometimes now called) on the shop floor, and were assured we could arrive at the same results with the dizzying array of buttons that allow the consumer to tailor the cycles to their wash load. It turns out that it doesnt allow this. Buttons are disabled on some of the cycles, thereby preventing recreating a Perma-press cycle. No amount of prodding... Whirlpool has provided me with an override for the combination of a normal wash and a gentle spin that comprise a typical Perma-press cycle.On contacting Whirlpool about the missing cycle, they claim consumers no longer want the Perma-press cycle. Puzzled by this statement, I returned to the showroom floor to see for myself. All the washers have Perma-press cycles. Whirlpool goofed with this model. They left it out. They have not provided a replacement machine for a consumer who blows this whistle on their goof. Among the solutions their customer support DID provide: add softeners to the rinse cycle and add dryer sheets to the dryer to reduce wrinkles [by purchasing a high-efficiency machine, we aimed to reduce waste, not increase it]. Among their invalid suggestions: choose the Casual cycle [there is no Casual cycle setting on this machine]; choose Normal cycle, then set spin speed to low [this machine disables the low speed choice on the Normal cycle]; on this machine the Perma-press cycle is renamed Delicate [Wrong. Delicate only swishes clothes back and forth, not robust enough for business shirt colors and cuffs]; on this machine the Perma-press cycle is renamed Colors [Wrong. Business shirts come out too wrinkled on Colors]. There has been nothing I can do to convince Whirlpool that they produced a lemon in this model [Model WTW6300WW0, Type 580] and should replace it with a normal washing machine. I have tried for years, only for Whirlpool to come to the same conclusion: its the consumers problem now, not theirs.

I bought my house brand new with all new Whirlpool Gold Series appliances. About a year and a half from purchase date, I started having issues with my fridge, then my dryer, then my washer, then my fridge again and that lasted about 5 months, then my microwave and my dishwasher. My microwave stopped working in January. It’s now April and I still do not have a new one. It keeps getting lost or shipped to the wrong address or something. Every time I call, the representatives don’t know how to look it up. I wind up on hold for at least 30 minutes, and I get transferred to at least 3 different people. I hope my last appliance doesnt break because I’m over Whirlpool, and I will never buy another appliance from them again.

Agreeing with many. How disturbing to buy a Cabrio Whirlpool washing machine about 5 years ago. I might as well go down to the river and wash my clothes. The bearings went out which means I have to be the spin cycle. I am hanging out my clothes on the line - very wet - until my husband buys the part and fixes it himself. I had my maytag for 25 years. An awesome, dependable machine that we laid to rest because of rust. We should have gotten another drum instead of buying this machine. Where are the engineers that are making dependable appliances to last a LONG time? We have not gotten smarter. Or we only care about the all mighty dollar. Make something to last a short time so that you have to buy again. We will do some extensive research the next time we buy a washing machine. Do not buy this machine!

Since my review I have been corresponding with Whirlpool Customer Service (Chris). First he sent me an email and mailed a replacement board to have us (the homeowner) install. Because the cover was so melted, the replacement board would not fit down into it. I emailed pictures to Chris. Once he saw the pictures, he called me and arranged for the water heater to be replaced since it was still under warranty. He even extended the authorization code so we would have plenty of time to arrange for a plumber to do the work. We had to pay for the plumber, but Whirlpool arranged for us to have a new water heater. Now I can sleep at night without worrying that my house would burn down if the old water heater caught fire. Chris was GREAT to work with. I had a direct number to him and called any time I had a question. I was very impressed with Whirlpools Customer Service.

I have Whirlpool 25 in. Side by side. I love the space freezer size is bigger than the old one I had. Makes ice as it should. Overall solid appliance that I trust. I purchased this refrigerator a year ago after research.

I bought a front loading Whirlpool washer a few years ago after having my old top loading Kenmore for 25 years. It seemed okay, but I did always have to leave the front door open and it always smelled musty, which was of some concern. My clothes never smell totally fresh. The biggest current problem is that several months ago it started with a failure code, alternately would stop without draining, wouldnt fill, or wouldnt drain, and ultimately ended up flooding my basement. So we called for service and they replaced a sensor and said these machines seem to have a lot of service issues with sensors blowing and motors dying. So I paid them that time. Now its a month or two later, failure code again, calling for service one more time. But if it costs too much I will join the legions of dissatisfied Whirlpool customers and will switch to an upright competitors brand.

Every washer Ive ever had has just a spin. Why dont these new washers? If the washer is un-level why would you add more water? They need a spin cycle to drain the water out of it. No more rinse and spin just a spin. Very aggravated.

I purchased a washer Type: 587-08, MOD: 1CWTW48004QO, Serial # C21920164 about two years ago. The appearance of the machine is in an excellent condition but its not working. The tub inside is slanted and makes a loud banging sound when rinsing. It is no longer in warranty. All my appliances are Whirlpool brand because my mom has items that are still 15years and over. This machine that I purchased did not even give me a quarter of that. The prices of these items are expensive and increasing all the time but the quality, durability and lifetime is diminishing at a faster rate. I am worried about all the other items I purchased: dryer, refrigerator, stove and microwave. I am most dissatisfied. I STRONGLY believe that this unfair and unlawful....I work hard and save up to buy these items to only get two years from it......Whirlpool please render some assistance!!!

Last year, our clothes started coming out too wrinkled. And until recently, its making a loud noise like an airplane. I called Whirlpool, and the only help they can give me is finding a company that would do service and would charge a lot.

Whirlpool Gas Range model GW397LXUB1 is a lemon. We bought our house new in 2008, and it came with Whirlpool Gold package appliances. Within a year, the console buttons quit working for the oven, and we had our warranty fix the console. Within another year, it happened again, and then again last November and now again this week. This range is obviously defective, yet the only solution was to buy for $350, a one-year warranty from Whirlpool. I asked if they had any sort of redress or rebate if we bought another unit, which they reported no. So I looked online for other people who have had similar issues, and counted at least 75. So this company knows they sold defective units, but wont stand behind them without substantial cost. All this simply assures me is that Whirlpool is NOT a stand-up company, and I can assure you that Ill never purchase any product from them again.

My husband and I purchased this washer in August of 2011. Within 2 years the lid broke because of it a cheap plastic frame on a heavy glass lid. At that time I researched it and found many people with the same complaint. Whirlpool would not do anything for us but the company that we purchased it from did agree to supply the part if we paid the labor. We did this and replaced the lid. Well here it is just right at 2 years again and the lid is completely broken and the washer is unusable. There is no way to bypass the lid issue which makes the washer completely useless.I called Whirlpool again and was told there was nothing that could be done and that because there was not a recall on the product, they would not be able to do anything for me. We have purchased a new Samsung washer that received excellent reviews from Consumer reports and we will NEVER buy another Whirlpool product again. I cannot believe a company that old and as large as Whirlpool will not stand behind a faulty design and faulty made piece of equipment. It is very disappointing.

Quiet Partner II - Our dishwasher racks started to crack and rust very quickly, about two years after purchase. We repaired the racks and tines, but the rust got worse. We replaced our dishwasher today with another brand. Many of the tines on the drying rack had rusted and broken off. We have been told to only purchase Nylon racks. I hope this is good advice. I must admit I had no trouble with the machine as far as cleaning my dishes. I just felt the racks should last longer than two years. Cost to replace racks was about the same as replacing the whole machine.

I purchased a Whirlpool Duet front-loading washing machine on September 27, 2010. By October of 2011, it was making a loud grinding noise during any spin cycle. I called for service and was told I needed new bearings which entailed rebuilding the machine. I had purchased a 5-year extended warranty. I was originally told by the warranty company they would replace the machine.After waiting two months, and after several contacts made by me to the retailers customer service, I was told the machine would not be replaced, but repaired. After the repair, on January 6, 2012, the machine now rattles and shakes so much during the final spin cycles. It is literally impossible to have a conversation with someone standing next to you in the same vicinity as the washer, it is that loud. I am sorely disappointed with the Whirlpool line of products and with the retailer who has been dragging their feet on customer satisfaction.

Whirlpool refrigerators with bottom freezers have a major defect in a tiny drainage hole hidden inside the back panel. The hole easily gets blocked with bits of debris during manufacturing or with a few bread crumbs, then it freezes shut. Then water ends up all over your floor. You cannot fix it yourself as you have to take apart the whole freezer. The repair bill is huge. This will happen often. Check on the internet and YouTube to verify & you will see that this happens to everyone with a Whirlpool. Also your floor will be ruined if you dont mop it up every few days until the repairman arrives! Stay away from Whirlpool!!

My story begins in August of this year when my wife and I built a new home. The builder provided Whirlpool appliances in the kitchen. The fridge has continually tripped the breaker and after numerous visits from the builders electrician, we finally also had the Whirlpool service technician check out the fridge too. After the control board was replaced, and the interior light housing was replaced, it turns out the wiring harness in the fridge is faulty and is not repairable. According to your customer service team, the fridge will need to be exchanged. I have made numerous calls to the suggested numbers (866-698-2538 & 800-253-1301) to find out the status of the exchange. Each time, I have been told that my file is with the review team, and that if I have not heard from them in the next three or four days, that I should call back again. I have not been able to contact the review team directly myself, as your customer service team is either unable to or is not allowed to share those contact details. So I am relegated to wait and then call back again. I have lost track of the number of calls I have made, and the hours spent on hold because of the high volume of calls or re-telling the whole story. The fridge was determined to not be repairable on November 19th. I am not sure if this is the treatment you intend for your customers, or if this is an anomaly.

I purchased a Whirlpool refrigerator less than a year ago and both the door and icemaker have a problem in which PC Richards, the store I purchased it from, has had to service the refrigerator at least 3 times and have not resolved the problem. The door does not close properly and every time I use the icemaker, condensation builds up. Each time a tech person comes to my home, a different reason is given. I need this problem resolved. I dont need to monitor the refrigerator like a sick patient.

I bought the front load washer 4 years ago. The tub bearing suddenly broke. We have 2 people in the house so the washer is not used more than 4 times a week. I was told it would cost $700.00 to repair. The washer was bought with a stackable dryer. Now Im told they no longer make a washer to go with the dryer. I called Whirlpool/Maytag and they could care less. The explanation I was given is that it is a man-made appliance. That is the worst customer service I have ever gotten. I would never recommend Maytag/Whirlpool. In fact I will highly discourage against it.

The first Front load Whirlpool washer leaked. 5 repair techs visits. Wasted days. Finally located the leak, in the main basket. Replaced washer. Second washer the clothes come out smelling like a horse blanket. Mold. Clean the washer every month still mold. Plan on junking the washer a getting a new model. Never expected this much trouble and time on a basic appliance.

Installers left and Home Depot Cabrio washer stopped with water left in tub. I reset GFIC outlet, tried again and it stopped. Did some research and tried different outlets. Same result. I discovered that if you shut off machine as soon as the GFIC is reset, then the washer will drain no matter what. I have been on the phone with Home Depot and they have no solution but to wait one week for a repairman. Very dissatisfying service. Now I am running a 20 foot, 3 prong, heavy duty extension cord into living area where there are no GFIC outlets and it has been running. I believe there is a fault in the washer, but they must not care if we get electrocuted from the faulty grounding of their Whirlpool product.

I have been using Whirlpool brand of appliances for over 40 years. They have always served me well and very dependable. Im a semi retired HVAC contractor and also installed Whirlpool heating and air conditioning systems in peoples home, also very satisfied with the results.

I purchased a Whirlpool 12-gallon point-of-use water heater as a booster when I was going to get a tankless and when we decided that we didnt need a tankless, I tried to get an RA number through the manufacturer so that the store could give me credit, as it says directly on the water heater, Do not return to store. They said there is nothing that they will do and it cant be returned to the store. So, what am I supposed to do with this water heater now? Before I knew this was going to happen, I purchased a 50-gallon Whirlpool water heater as well. So now, I have the 50-gallon that I have had to replace the element for already and I have only had it for less than a month and a half, and the 12-gallon is just sitting in my garage. Im completely irritated with this company and do not recommend anyone to go with this company! This is the worst customer service!

Weve had our Whirlpool Cabrio washer and dryer just over a year. I like them both but then we are having problems with our lid. The first one cracked after 9 months and they replaced the lid. Two months later, the new one cracked and they replaced the hinges and lid again. I assure you we are very careful when lowering and lifting the lid. I do 80% and my husband does 20%, and we are very cautious of it especially after the second one broke. Now, I was just putting laundry in and the third one cracked while lifting the lid. There is obviously a problem, and Im wondering if anyone else is having the same issues. Eventually, it will crack all the way through which will cause the glass to pop up and the lid wont lock. I will not buy anything with a glass lid again!

Yesterday morning I was in my bedroom when I heard a bang... I went in to the kitchen and looked around and couldnt see anything. Then I saw my cat sitting on the floor and looking up at the microwave... It was then I noticed that the glass on the front was all crazed and making a tinkling sound. Several pieces had fallen on the stove top underneath. I had to call the repair man who said he had never heard of this before. He had to remove the door. I could not use my stove with the danger of glass falling in to food. He had to order a new door and I had to spend $65 then. When he puts the door in, it will be another $200 or more.

In November 2014, I purchased a Whirlpool 22 cu ft side by side refrigerator from my local appliance store. During that short time, there have been 4 instances where the ice clumps together and gets stuck, causing a large amount of ice to dump inside the freezer door. When the door is opened, the ice falls out onto the floor. I usually spend 10 minutes picking up ice and wiping up my kitchen floor. I have had the local store repairman over. He told me that was normal. Two things are seriously wrong with that statement. When I spend 1600.00 for a brand new appliance, I should be able to depend on the fact that it will function in at least a somewhat acceptable manner. Additionally, that statement by the repairman convinced me that he was not really interested in fixing the problem. I really dont think the normal operation of a new appliance is for it to make frequent, large messes for the owner to clean up. This appliance is junk and you would be foolish to purchase it. Spend a bit more money and buy a Samsung or LG. Save yourself the frustration and sense that you have been cheated and deceived by Whirlpool. I will never buy this brand again.

I purchased a Whirlpool water heater on 9/30/2011. It is leaking at the point of cold water entry and is spewing a brown colored watery substance, leaking on the floor.

Similar to what I am reading below and on other sites, my hot water heater stopped working. I spent about an hour trying to relight the pilot light, which apparently you cant do with this model because it breaks. My first thought and action was to call a plumber to come fix it. When he arrived he said it was reverse thread and that I would have to call Lowes to get a replacement part. When I called Lowes they said they would call Whirlpool and then give me a call back. Two days later I still havent heard back or taken a shower; I am going to the gym tonight. Finally, I got online and called the 800-number and am being sent a part to arrive tomorrow. I asked to be reimbursed for the cost of the plumber since they obviously knew they had a problem (they assumed why I was calling the warranty line) and redesigned the issue with a voluntary recall. Whirlpool, please make this right. I know you license your name to American but it is still your name and brand reputation.

I purchased a Whirlpool WTW6600SW in January 2010. I dont normally purchase an extended warranty, but it was a fairly expensive washer. So I did. In July 2011, water starts gushing all over the floor. After my first visit to see what is wrong, I ordered a part. I was out of a washer for 2 weeks. Then in August 2012 the same thing happened. This time the repairman didnt get the part on properly, so they had to come back a third time. I am out of a washer for about 3 weeks. Now, October 2012, it is doing the same thing again! Customer service tells me it has to be repaired for the same problem four times in the same 12 months in order to receive any replacement value. It will have to break two more times! This washer is a piece of junk!

Whirlpool electric range with ceramic cooktop - I have a large black mark on one of the cooktop burners that appears to be beneath the surface of the cooktop. It’s almost within the finish of the burner and unable to be cleaned with cooktop cleaner. I have purchased an extended warranty and arranged for a service call. The repairman came out as scheduled, but informed me after making a phone call to who knows, because he did not tell us that the problem was cosmetic and could not be repaired under warranty. However, if we wanted a replacement cooktop, it would cost almost as much as a new stove. He also said that he had seen many of these ceramic burners with that problem and it was not unusual. All I really want is what is fair, a defect that is not my fault that needs to be replaced. The stove (Whirlpool electric range with ceramic cooktop) was purchased in 2004 and is kept very, very clean.

Purchased Whirlpool refrigerator at Lowe’s. Refrigerator would never get cold enough, so I exchanged with a Whirlpool Gold side-by-side refrigerator. After installation coffee was spilled behind refrigerator. I was unable to pull refrigerator out from wall to clean coffee spill from behind. When checking with Lowe’s on the 35th day, I was informed that Lowe’s 30 days warranty had expired and I would have to work directly with Whirlpool.I discovered it was very hard to communicate with Whirlpool; there was a problem that they only had on file the first refrigerator I purchased not the one I kept. The Whirlpool service rep did not seem very cooperative but with insistence they told me they would change my information to the correct model and serial number and a repair order was sent to a local service shop. The problem with not being able to roll the refrigerator out from the wall is that Whirlpool had changed their wheels to a tri-wheel support and there was not enough height on the single front wheel to lift the refrigerator to clear the screw down leveling stops on each corner. The service rep had no solution for the problem and had to call the Whirlpool service. He indicated he never was able to get assistance from that department. I told him I would talk to them as the consumer but they refused to discuss the matter with me, so I gave the phone back to the service tech. Whirlpool told the service tech to order replacement wheels of which I knew this would not resolve the problem.After two weeks, the replacement wheels arrived, the service tech installed them and as I expected they did not resolve the problem. I then requested the service tech to remove the rubber from the stops on the corner to allow for the additional required clearance and this solution worked. This is a very poor design for Whirlpool, but I accepted the results. Two weeks later I receive a phone call from the service business and they tell me that Whirlpool did not have the refrigerator model/serial number they worked on. Whirlpool was not willing to resolve the problem I had with them initially and the service business would have to bill me directly and was not covered under the warranty.At this point I lost it and informed the service business I resolved this model/serial number with Whirlpool before. Whirlpool gave them the authorization to work on the refrigerator and they would need to collect the fees from Whirlpool. I have purchased my last Whirlpool appliance mostly because Whirlpool makes it very difficult or refuses to talk to the consumer and it appears the quality is no longer there. Will Whirlpool become the next Kodak? With this kind of service, people will just quit buying from them.

I bought a dishwasher Gold Series Top Control Whirlpool dishwasher at the Home Depot, April 4, 2015. Paid six hundred ten dollars and twenty-eight cents $610. 28. I noticed soon after that the top shelf falls off the rack when loading at front. I began loading from the back. It worked for a while but now it totally fall apart. The door will not close and I am unable to use the machine.

I purchased a whirlpool under counter oven - my main reason for not buying something cheap was the safety of my family - I chose the AKZM656 eye level oven. The stove is about two years old, but we do not use it that much. Two days ago my wife set the timer and placed a dish in for cooking; she then went outside to water the garden. About twenty minutes later she returned as something was burning- the oven reached a temperature of 350 degrees and would have burnt the whole kitchen down if she did not spot it. Now surely the oven should be designed to switch off if sensors fail? I reported this to Hirsch (Ballito) but they say they have no one servicing the Richards Bay area. I am not sure if this stove should be fixed as it is obviously not safe and makes me wonder how Whirlpool get safety standards passed on these items. Surely you expect better when buying a well-known whirlpool brand?

As with other posts here, the rear bearing is going out of Whirlpool Duet front loading washer. I purchased mine in late 2008. Moderate use always according to recommendations. I called Whirlpool and same story--no recall and it would be expensive to have it repaired. I cant see putting $400 to $500 in parts even if I repair it myself. I cant believe that with such a common problem, Whirlpool wouldnt either honor a repair or offer a reasonable bearing package to fix. It requires the entire back, half of a new drum. Poor design, but whats worse is no effort by Whirlpool to rectify the situation.