Weve had this washer for about 9 months now. We noticed that the loads being washed small or large werent coming out clean. When wash cycle finished items were covered in soap residue and or had large dry spots where water had never touched the area. When our sheets were washed in bulky/sheet cycle and deep water this happened. Maytag sent out repair person to find the water pump went bad, pump was replaced. After repair same bad washing results as stated previously. Maytag then sent out repair person for the second time. This time the main electrical board was replaced. Still after two repairs wash loads are still coming out dirty, soapy, dry in spots in any of the selected wash cycles large or small. Third call to Maytag and a third scheduled repair date coming up in a few day. Over the phone the Maytag employee only words of wisdom was, Did you buy the extended warranty. So unless there is a third failure I believe that this washer is just a poor design.

4 year old gas range, used self clean mode yesterday, for first time, upon completion opened oven door, not very clean and found 1/2 moon shaped raised crack in center of oven floor. Customer service insisting repair tech must come at cost of $60.00 to determine cause. I believe this is manufacturing defect, that they are not willing to admit. Offered big discount on new range. NO MORE WHIRLPOOL FOR ME!!!

My Whirlpool microwave heating plate is not rotating properly.

Cabrio Washing Machine - I purchased my washer and dryer in May of 2008. I had problems with sheets, towels and pants getting very twisted and tangled, but I just attributed that to a design flaw. My problems really began in January 2013 when loads were not level all the time. It didnt matter if it were 1 shirt or a load of towels; you had to stand by the machine and it took forever to finish a cycle.On 1/11/13, the first repair was the rods that kept the drum stable. $260.82 later, it worked again. On 2/16/13, the washer quit working. On 2/18/13, the repairman was back out. It needed a lid lock switch. It was $87.14 that time and he would be back when the part arrives ... There was still no washing machine. On 2/21/13, he returned with the lid switch and replaced it. That was $178.04 but wait, there were still other error codes so there was no working machine.I refuse to pay anymore as I now fear I will be buying a new machine after spending over $500 in less than 6 weeks, but Whirlpool did the right thing when I called and they agreed to repair the machine. They wanted a different company to come diagnose the problem (the machine gave an F50 and F51 error code to the repairman here on the 21st), so I have to wait for another repairman to come and look at the same codes flashing on the LED readout.On 3/1/13, the A&E repairman that Whirlpool sent out arrived at my house. I have been without a washer since the 16th of February. He diagnosed the problem and said that it is a $1,000 repair! I called Whirlpool and asked for a new machine, instead of throwing more money at this one. They informed me that if I didnt like their offer, they wont do anything then. I agreed to the repair.Parts started arriving at my house. On 3/13/13, another A&E repairman came out and started to fix the machine. He informed me that there was more wrong than the first guy thought, but he had the circuit boards so he would get it going. On 3/24/13, the washer quit working again and was flashing an F51 error code. This is the biggest piece of junk I have owned in my life. I have missed 5 half days of work since January and there is no end in sight. Why is Whirlpool allowed to get away with such an inferior machine?

Purchased a Whirlpool WRF990SLAM fridge in 2013. Ice maker went out and the evaporator. Service tech said he needed permission from Whirlpool to work on. Would definitely not recommend purchasing this brand.

The first thing I noticed after purchasing this stove was that the glass top did not clean properly. I used the product given to me by Sears and tried several others but still could not take marks off of the glass top. I never really used the oven that much until retired and started baking often. The self clean does not work at all unless by self clean they mean that you yourself cleans -- I should say scrub it down. I previously had a regular self clean and it truly self cleaned. All I did was take wet paper towel and wipe out. Yet when I asked the Sears saleswoman about how it cleans I was told that it was terrific -- I would not have any problems! What a laugh!

I purchased the 19 cu. ft. Whirlpool Estar refrigerator WRT 3595FYW on 4/28/12. Freezer began showing frost immediately. Repairman from Marcellas Appliance where purchased - (518) 381-1957, came to check it, put a sealer around the door openings of refrigerator and freezer. Frost continued. I called Whirlpool. They sent another repairman from EB Russell in Schenectady, NY, door needs replacing. Door was ordered and when received by them, the door was replaced on my refrigerator.In August 2012, frost is in freezer, on its roof, on the door daily. I called Whirlpool. I told them I wanted to remove it from my home. Whirlpools reply was, you have a repair warranty, not a replacement warranty. I was not advised of this when I purchased. Otherwise, I would have gone to Sears, Lowes, etc. On 8/16/12, another repairman from The Appliance Man, Albany will be here Monday. Its dishonest sale, replacement was advised possible by Marcella, that it was just a matter of course to get an okay from Whirlpool. This is not so. There is no replacement or return policy. Please help. Thank you.

My dishwasher was a $300ish model from Lowes. It is over 5 years old and has been reliable for a single persons use. It is run about once a week on average. Early on I had problem with it not cleaning well but that was the fault of one of those no leak supply hoses that restricted flow...fixed that. Would I buy again? Yes.

WTW4950XW2 - I purchased My whirlpool washing machine wtw4950xw2 from best buy in 03/30 2013 and it just stop working after 3 yrs. The manufacture warranty was only good for 1 year. I think companies does that on purpose because they know these new equipments are not going to last. I think before they use to have at least a 3 yr or better warranty on appliances. First it started making this loud sound when on the spin cycle, so I had a repair guy come out. He told me that the bearings needed replaced so (how does bearings goes out in 3 yrs). I asked how much will it be to replace parts/labor. The Parts cost $250 and the labor is $200. I might as well buy a new washing machine. I am so disgusted with this machine. My previous Whirlpool, which was not the new modernized, I had for at least 12 years and also I bought a whirlpool dryer. My Dryer stills works after 15 yrs. Im going to try to hold on to the dryer until the long haul. I wish I just would have gotten my old washing machine fixed. Now Im looking for a new washer and I wont be doing a whirlpool or anything with a push to start - just a plain old agitator, no sensing mechanism, just basic.

Bought a $2500.00 fridge in Dec. 2012. By July, we were dealing with our 4th repair. Customer service in warranty department is non-existent. They act like you are a bother and have no right to demand replacement. I sent an email. No response. I wrote a letter to Corporate. No response. Not until I made comments on Facebook. Then I get a call offering me an extended warranty (which I already had purchased) so they said they would give another year (total of 3). This was a few weeks ago. I still have yet to receive anything or hear anything. This morning, our fridge is on the fritz again. I am loathe to have to deal with them again, but have no choice. Its either deal with them or throw out the 8 month old unit and buy something else. I should not even have to consider that. Whirlpool is a huge company. I do not understand their reluctance to just replace a product that is obviously defective unless they have no confidence in a replacement unit. This is so frustrating and upsetting to me. I did my research. I thought I was getting a quality product from a quality company. What a disappointment.

2 years ago, we remodeled our kitchen. We replaced with all Whirlpool appliances. WHAT A MISTAKE! Our ice maker went crazy 1 month ago and now our dishwasher almost caught fire Memorial Day weekend while we were away! Thermal Fuse and stainless interior prevented us from losing our house to fire but really Whirlpool, you spend that kind of money and all appliances are breaking before theyre even 3 yrs old! My husband is very good at fixing things but when he diagnosed dishwasher, he said he has to find a way to fix wires in control panel because melted insulation. Now I am afraid of it. So if you purchase Whirlpool, expect maybe 2.5 to 3 yrs service and think of them like a disposable lighter, use it and throw away.

I have had a $3000 GE Profile fridge for 6 years. It died. Tech says turf it. I bought a whirlpool. Hopefully it lasts longer. These expensive fridges seem to be very undependable. What is a family supposed to do when a refrigerator stops working and repairs take days or weeks? Is there a courtesy fridge for a loaner? They are big and heavy. What a royal pain.

Our new fridge, which was already an exchange from another unit that went bad, kept freezing things in fridge compartment. A tech was sent out three times and then the compartment quit working completely. They stated they would replace for us, only way they would replace was to have them ship a new unit which would take two weeks. So we are without a refrigerator for two weeks. Asked if I could go buy one and be reimbursed. I could but I would NOT be reimbursed for full amount. The company reps I spoke to could have cared less about our situation especially Fred who supposedly is a supervisor. Do yourself a favor...DON’T buy Whirlpool. Their customer service sucks!!!

I am getting numerous F1 codes on my Whirlpool Cabrio washing machine, Model #WTW6600SW2. By doing thorough research on this issue I can see the problem is in a known defective control board (part #W10130544). This part has even been replaced by Whirlpool with a new control board costing around $300 for just the part. After calling for repair service, two people (1 agent and 1 supervisor) refused to acknowledge any known issues with this part and further refused to any type of repair or replacement of the part. It is impossible for anyone in that position to not have knowledge of this problem. Simply look on the internet for a countless number of people with this very same complaint. Even though my washer is eight years old it has had very little use. There are only two grown adults in this household and the machine has never been abused or overused. It still looks new. Whirlpool should be honest and responsible when dealing with this type of problem. They should agree to pay for the part and repair service... at the very least they should agree to pay for the part.

I bought my microwave on Dec. 8, 2010 and paid to have it installed. On June 29, 2011, the microwave quit heating anything up so I called Whirlpool. They sent a technician out and he repaired the magnetron. The tech said it was defective. I accepted that but then on Nov. 8, 2011, the microwave quit again, same problem. I called Whirlpool and told them I thought it was a lemon and wanted it replaced but they refused and said that they paid to have it fixed. They came out and fixed it. Same problem, the magnetron. Well, here we are another six months later, it has quit again. I have been on the phone with Whirlpool. I spoke to a lady named Barbara and she said even though its out of warranty, they would be willing to pay for the parts, not the labor. Of course, labor is more than the parts. So, I asked her whats going to happen another six months from here on. When it goes out again, she said that that was it. They werent paying for any more parts. I asked her for her supervisors number. She advised me to write a letter and someone would call me. Well, a lady named Donna did call and she told me the same thing. They would pay for parts but not labor and the offer was only good for 30 days. Also, I have the tech talk to their techs but she didnt have the number and maybe they could find the problem. Well, the problem is its defective. Thats all there is to it. We could fix it over and over again but its going to keep burning out. I told Donna surely I cant be the only one complaining about this microwave and her response was theres no recall on it. Something needs to happen. This cant be right. We spent hard-earned money on this product and shouldnt have such a problem every six months.

I purchased a Whirlpool catnip washer from Brandsmart in August of 2010. It worked fairly well, but would sometimes need for clothes to be rearranged in order for the spin cycle to complete. In June of 2013, it started to not wring the clothes out completely. It then stopped working. I called a repairman and got an estimate of $550 dollars, but I paid $578 for it.I called Whirlpool and spoke to the supervisor of the consumer concern team. She offered me a fifty percent discount on the parts for the repair. I checked the web to see if anyone else had any problems with this product and found several. I suggest you do your homework before purchasing a Whirlpool washer. I was positive they would do more, since it’s such a prestigious company.

When you buy a global brand name you expect it to work the first time around. If not, then you expect to have it exchanged not repaired. The microwave did not work out of the box. They made me take it to the shop for repair. I would have expected an exchange for another one and an apology from the quality control guy who should have checked it. Apparently Whirlpool (Mexico) doesnt give a rats ass about their customer base. Its all about getting as many units out the door with poor assembly and no QC.

I am very disappointed in my purchase of Whirlpool High-Efficiency washer and dryer. It does not clean my clothes! I have white towels in my bathrooms, I have them for years. They have always come out perfectly white with the regular washer I had for years. Not any more! They now come out with yellow spots all over them. Dark clothes come out with a white residue on them that looks like there has been a napkin in the wash. I talked to Sears where I purchased it, they said I might be using too much detergent, so I have tried using less to no avail! I hate my washer!

I bought a Whirlpool/Fridge Freezer Model WRF560SMYM 01, less that two years ago. Two months ago it started making a terrible noise. Apparently the freezer was iced up and a mechanic defrosted it. It happened twice more and he left saying he could not fix it. Another arrived and took the model number and he disappeared. A third the same. Now I have an empty freezer, just an ice maker. It seems to not freeze up so quickly with the moisture control on. Over $2,000 down the drain unless somebody can fix it. Oh and the fridge gets very cold! Does anyone have any ideas apart from throwing it out and buying another? Never another Whirlpool!

It is a good refrigerator for the price, but it is not big enough for our family. It does get very cold in the refrigerator part unlike our last refrigerator. I only wish it had more shelf space on the door and the egg place fit more than 6 eggs.

We have had this Refrigerator for 3 years in December of 2016. To date, we have had to call a repairman (in February 2016) to replace a circuit board on the back of the refrigerator. That took 4 days, as the company sent the repairman the wrong parts. After that $300 repair, which we got at a discount because, the repairman felt bad that the company actually sent the wrong part. Since then we have taken it apart ourselves for several reasons: The freezer compartment filled up with a layer of ice and started to melt all over the floor, shutting the refrigerator off, (which then forced us to borrow coolers to store the food) until it could be repaired. The drain tube was completely blocked and in order to fix this problem, the tube had to be taken out and modified, according to the Internet videos we then watched. In order to make all of these repairs, the door, the shelves and baskets have to be removed, which is definitely not an easy thing to do at all.There are so many hidden screws and tabs that must be manipulated with tools and by hand to remove the doors, shelves and trays just to get where you need to be in order to make these repairs. With each repair, the ice maker and water dispenser started having problems, because, each time the refrigerator has to be shut down, it takes hours for it to re-set itself. Luckily my husband had the tools necessary, with videos on the Internet to assist us. However, once the first problem started, it was a snowball effect, literally. ALL of these problems have been identified by the manufacturer, however, nothing has been done. VERY POOR DESIGN!

I own a Whirlpool Cabrio. I wanted a newer technology (no agitator) washer with top loading capabilities. I ended up with a four to five-year lifespan with this washer. The bearings are busted and it leaks water from the bottom. I have followed loading instructions specifically. It will cost about $1,000 to fix so of course, I am buying another washer and a matching dryer.

I purchased this washer two months ago and have been greatly disappointed with it. I put in a large load on wash cycle, but the rinse cycle is barely any water, and is all soapy water, so then I have to turn it back to wash cycle to get more water and then back to rinse to finish it properly. I was never told about the short water cycle, why not? It is still under warranty, but said I have to deal with Whirlpool, and all they can do is send a repairman out and if it is not a defect, it will cost me $130.00 for the service.

I bought Whirlpool hot water heater with the Honeywell part in 2014 and the thermal box went out. No flashing lights, no way to reset. I understand that Whirlpool had a class action lawsuit after researching. Still selling this product to consumers. Whirlpool should be held responsible, and be made to give an allotment to replace homeowners with hot water tank of choice! If lawsuit is active please add my name.

My complaint no. ** date 11/07/2014 till date 06/08/2014. Its noted solved by services department after 100 calls by me. They Reply no parts available from company so if you buy washing machine, be careful about Whirlpool washing machine.

I purchased a 50-Gallon Electric Water heater in 2006, sure it lasted and worked well for quite a few years; however, in August 2014 my power bill started to rise dramatically, I live in Arizona and $300-$400 power bills are the norm in the summer months; however, a $700.00 bill will immediately be noticed. I contacted the power company and they sent a tech over who performed a lengthy diagnostic and determined that my water heater was running constantly thus accounting for the great increase in power, I contacted Whirlpool and received 2 heating elements (no charge) which my pricey plumber replaced.The problem still remained and I contacted Whirlpool again and again trying to get this issue resolved. I paid less than $400.00 for the heater installed and since Ive been having the issue Ive almost paid another $400.00 in labor costs trying to get a resolution. Ive decided to get another system and my only reason for posting this is to inform all that the Whirlpool heaters seem to be very problematic, like others Ive had plumbers decline my business when I inform them that I have a Whirlpool tank with the Energy Smart module.

My silverware, when it is washed, a piece or two comes through one of the openings in the basket and I have to work it out before I can lift it out of the dishwasher (MOD WDP320PAD50 Serial #F4432749) to put the pieces away. Please update your dishwasher by making the openings smaller for the silverware so I can stop cussing. Send me a new basket when you do. The dishwasher was in a new home I bought.

I purchased the Whirlpool Cabrio HE top loading washer and front-loading dryer about 7 years ago. It has been okay, but nothing special. Recently it began stopping in the middle of the cycle and showing an F51 error. Then all of a sudden the noise during spin was deafening. Brought out a tech, who came and did some eval. Left with some basic maintenance. Did a load, and happily no more F51 code, but still so very loud during spin cycle.Called again; tech returned and said that drum and shaft would likely need to be replaced to the tune of some $500. The same story as others have told. We should have bought the extended warranty. Like others, I also felt that washers lasted at least 10 years. And that seemed a short time given expectations in the past of 20 years of service. Im disappointed in Whirlpool. Even though Consumer Reports gives the Whirlpool Duet washer (new 2013) one of its highest reviews, I cant bring myself to buy another Whirlpool product. It appears to me that this warrants recall as well.

I have always used Whirlpool products and have grown up with them. From washing machines to dishwashers. Not only is it made in the USA but its reliable. The only problem is space and it can do with more freezer space. Other than that its a great refrigerator.

We purchased a higher end cabrio model only 3 years ago. Last year, on about every 5th cycle, the load would not spin at the end. Id have to remove all the wet clothes, set it to drain and spin, start it and wait for it to hopefully kick in. When I do it right, it kicks into the spin mode. I had to quickly press start/stop to unlock the hatch and reload the soaking wet clothes and wait for it to spin properly. Yesterday the same thing happened again. This time, it did not kick in. I ended up flipping the washer over and taking a look underneath. I discovered that the motor was seized. It had lost all its lubricating oil and smoked the belt. Now, my 3 year old washer is sitting in the driveway awaiting a trip to the dump since I got fed up and went out and purchased a new Samsung top loader. I emailed and called whirlpool with no luck. Not impressed. When I went out to buy a washer today the first thing I told the salesman was to stick anything with the name whirlpool out in the trash bin out back.

Piece of crap! Approximately 18 months of aggravation. Clothes don’t come clean, leaves residue on them. Just absolutely the worst experience I have had in six plus decades of doing laundry. When next I get a washer...it won’t be a Whirlpool or anything made by the company. There should be recalls on these washers.

We are now over a month without a working fridge/freezer because of the lack of Whirlpool care. Our brand new Whirlpool fridge stopped working after 3 days. That was nearly a month ago. I have wasted hours on the phone with rude reps from both Home Depot and Whirlpool. A new one with multiple dents was attempted to be delivered today which I wouldnt sign for knowing Id be stuck with it. Now we have to wait 2 weeks for another one. A $100 compensation doesnt nearly cover our food loss let alone a family of 4 living without a functioning fridge and freezer. I will never purchase Whirlpool again!

I purchased the Cabrio washer about 2 years ago. This summer, I began to hear a roar in my washer when it was spinning. I called a repairman and in order to fix it, the tub has to be replaced and it will cost $258 plus service call. My sister purchased her Cabrio 3 years ago and her washer has the same problem. This sounds like a recall issue to me. I think Whirlpool needs to recall this washer or pay my bill.

The buttons that turns on the burners and oven turn on with a very light touch and start leaking gas and sometimes light. Its very dangerous and has done this since We got it new from Lowes. I wonder if there was a recall on this model or if lots of other customers have had the same trouble. Model #WFG524SLAS O Ser. # R20910336 We have had this stove about two years and My wife has kept after Me to report it , but I never realized how dangerous it really was until now. The previous stove We had you had to push in on the buttons and then turn them before they would light. Thank You.

I bought a Whirlpool Dishwasher, Model No. GU3600XTVY in July 2010 for $844.30. In August 2011, it failed to clean dishes. The repairman said it needed a new heating element and computer board which costs $319.92. Today, he installed the new parts and it still wont heat the water! Now he wants to take it in to the shop to check the wiring.My previous Dishwasher was a low quality builder-installed GE that lasted 16 years without repair. If we Americans accept that 1 year is an acceptable life span for consumer products, we will continue to have this type of trash sold to us. Made in America is now the product you dont want to buy.

In November 2014, I purchased a Whirlpool 22 cu ft side by side refrigerator from my local appliance store. During that short time, there have been 4 instances where the ice clumps together and gets stuck, causing a large amount of ice to dump inside the freezer door. When the door is opened, the ice falls out onto the floor. I usually spend 10 minutes picking up ice and wiping up my kitchen floor. I have had the local store repairman over. He told me that was normal. Two things are seriously wrong with that statement. When I spend 1600.00 for a brand new appliance, I should be able to depend on the fact that it will function in at least a somewhat acceptable manner. Additionally, that statement by the repairman convinced me that he was not really interested in fixing the problem. I really dont think the normal operation of a new appliance is for it to make frequent, large messes for the owner to clean up. This appliance is junk and you would be foolish to purchase it. Spend a bit more money and buy a Samsung or LG. Save yourself the frustration and sense that you have been cheated and deceived by Whirlpool. I will never buy this brand again.

I purchased a new Whirlpool Cabrio set, in 2009. I bought the top loading washer, and matching dryer. Since 2009, I have had the washer serviced FIVE times. Bearings, water pump, F1, F2, ul codes, and a few other things, I honestly cant remember. I love this capacity. But that is all I love about this machine. Today, the water pump went out again. I have been reading online regarding loose coins making their way into the drain pump, the hose, and other parts of the washer. I am diligent about emptying my pockets, but, obviously, someone in the house is not. There should be a trap for the coins, buttons, and any other debris that passes through, but, clearly there is not, and it appears I am not the only one with this problem. I am so frustrated. I paid almost $3,000.00 for this set. It was my very first brand new set and I have had so many problems with this. With all of the problems and all of the complaints, and so many similar complaints, why is Whirlpool not acknowledging them? Why are they not doing anything about it? Side note, my dryer works fine.

I hate the thing. The grates are way too large, they are too heavy, and the fact the high is not a true high and the other three are different temperatures. The oven is awful. It half cooks. You cannot do decent canning on the thing because you only have one burner. This is a mess from the get go. Why in the hell do companies think everything has to have a computer attached to it? Computers and heat do NOT mix for Gods sake. A simple gas stove is sufficient to cook with. Take the computerized junk off and make a normal stove.

Our hot water heater (Whirlpool Mod # BFG1F404053NOV) stopped working. I called the Whirlpool help line and was advised to change the thermocouple as they had been having issues with this particular model. I was advised to go to Lowes, where we had purchased the heater, to get a new thermocouple at no charge to us. After changing the thermocouple, guess what? It still didnt work. I went back to Lowes and they replaced the heater, at no charge to us (they were great during this whole ordeal so no knocks against Lowes). Well, one year later, it’s the same issue. The pilot light will not stay lit. It’s very frustrating as it never goes out at an opportune time. In the past, the name Whirlpool ensured you were getting a quality product. I guess that’s not true anymore.

I purchased an HIE washer one year ago this month. I have never been happy with the cleanliness of the clothes when they came out of the wash. The only way to get them moderately clean is to wash a few items at a time and even then the whites, especially socks, seem dingy. I noticed the new Whirlpool washers now have an extra setting to add more water to the machine, so the executives have realized there is a problem with the original model.I think Whirlpool should give all customers who previously purchased the models without this feature a trade-in option to get the newer model that fills with more water or for another model with the full spindle that has worked well for so many years. I have been very unhappy with the performance of this washer and would only hope the executives would do something to resolve this problem and satisfy previous customers.

Ive had this refrigerator at an upscale rent house for 2.5 years. I have invested over $1,000 in repairs, all of which happened after the one year warranty was up. Now I have to replace it completely because it makes a loud noise that my tenants cant stand. Dont buy this unit.

Six warranty visits and the fridge still doesnt work. Cools to around 44 degrees in the upper part and lower part barely freezes. We have gotten sick from food left in the fridge after two days from the grocery store. It is now approaching two months without the use of our new refrigerator. DO NOT buy a Whirlpool. Apparently there was a manufacturing defect. We are now learning that a $2,400 fridge doesnt seem to be able to be fixed by factory-trained specialists.

Bought this washer in May of 2019: Whirlpool - Whirlpool - 4.5 Cu. Ft. 37-Cycle High-Efficiency Front-Loading Washer with Steam and Load & Go™ XL Dispenser - Chrome Shadow. Model: WFW6620HC. SKU: 6313774. Paid over $1,000.00 for it. FIRST TIME washing our sheets, we had snags & rips. I immediately called and was referred to Whirlpool and then referred to an outside repair company. They sent a technician out who said everything was functioning properly despite having ruined 3 sets of sheets (these were not all washed at the same time & I didn’t realize they were being snagged until making the beds).I continued to use the washer - clothes were fine, but yet again, MORE sheets and now comforters RUINED!!!! I called YET AGAIN after troubleshooting the problem myself and finding that the drain holes in the drum had metal pieces sticking up causing the items to snag & rip. Another day taken off work to stay home for the repair. The repair guy comes out, the part was broken. So now I’m left once again with a faulty washing machine AND no ETA on when the new part will arrive and be installed AND having to take yet another day off work.7 sheet sets, 3 comforters, multiple shirts, & multiple bathing suits RUINED & was told there was ‘nothing they could do!’ I will NEVER EVER AGAIN purchase anything with the Whirlpool logo. It’s JUNK! Just an FYI, this was initiated in May of 2019 and it is now the middle of September 2019 with no fix updates. Who can go months without doing laundry???? Once again, poor customer service and JUNK of a product!

We bought the Cabrio less than 5 years ago. First of all, a high-efficiency washer should not require an extra rinse after each wash, but this one does. I cant see how thats being efficient. The washer, even for a small load, can take up to 54 minutes, and then when you tack on an extra rinse, its well over an hour, so what you may be saving in water, youre spending in electric and wait time. And then, there is still a soap/water scum left on the clothes, which is only evident on the darker clothing. Now, just recently, the washer is stopping, and NOT unlocking after about a minute into the start cycle. I will have to cancel the wash, turn it off and unplug it before I can get it opened. Im sure its something to do with the electric panel, which after reading the reviews, we are not going to fix, and we are headed out to buy the traditional top loader, NOT high efficiency, which I suspect will still be more efficient than the Cabrio.

I called in a claim on June 10, 2016 & my washer is still not repaired. The extended warranty company, AIG sent L&W out to repair my washer. After 3 visits its still not repaired & the technician hasnt fixed it. Not only that he had laid it on concrete & scratched the outside. This is the worst experience Ive ever had with a warranty company or service company. Aig wont even return my calls. Will never buy a Whirlpool appliance again.

This Whirlpool washing machine is over 5 years old and very reliable, I use it several times a week and have had no problems with it. Next time I will purchase a larger capacity machine so I can wash comforters and spreads easier.

I have been noticing my husbands shirts as well as my clothes continue to get what are spots of bleach and I do not use bleach on anything other than whites. This has been going on for quite some time and I noticed this morning another outfit is RUINED because of bleach spots. I decided to look up on the internet if this is a problem with this machine - AND IT IS! I am so disappointed I could cry. The clothes I have are donated to me. All my clothes are hand-me-downs - and my Whirlpool washing machine is ruining all my clothes and my husbands.

Bought a French door whirlpool gold, wanted a good long lasting fridge. Bought in late 2011. After having it a couple of weeks we noticed the ice maker would take days to make ice. So we called to have it looked at. The repairman said if it is slow, switch it to fast ice. It made ice even slower, but the repair company said if it is making ice, and he comes out, we would be charged. So we lived with it. In 2014 it stopped making ice at all. We called they sent someone out and said it was a control board. They had to order it, and came back a week later to put it in. They left and said we would have ice soon. Never did!!!So we call again, they come out and said no power to ice maker. He called Whirlpool and they said wires in the freezer door were worn and broke. Well the door is non-serviceable and the cost of the door will exceed the price of the fridge! What kind of crap is that!! Long story short I will never buy another whirlpool again, and when I hear of someone buying new appliances I warn them to stay away from whirlpool!!! Run!!!

The Gold Series Whirlpool dishwasher has some cool features for changing the configuration of the shelves, etc. After that its all downhill. Poor washing, worse drying. In the past 6 months Ive tried: less dishes, redistribute them differently every use, lower/raise upper shelf, use liquid detergent, powder packets, drying agent... nada. Absolutely NO remnant of food can be on the dishes. Of course I rinse everything well prior to loading washer; this one wants them CLEANED. I dont give a flying fig how loud a machine is as long as its doing its job. This one quietly does very little. AND the genius who designed that horrid cutlery basket needs a new job.The basket slides onto the inside of the door, making it difficult to reach into; it can sit on the outside of the lower tray but it falls off at the slightest disturbance. The baskets are narrow with hinged lids; the lids have small and medium slits so items are placed individually. If your cutlery is the right size! Ours is a little wide in the handle, they dont fit and must be placed into the opened, narrow baskets and butt up against each other. We are only 2 folks, I cook one meal a day and run the washer TWICE because bowls and pots take up the entire space, so I either wash the remainder by hand or keep the sink full of dirty pots and dishes. LOVELY. Bring back the old washer!!!

My double oven is only 6 years old - it stopped working on xmas day, had a repair man look at it. He has phoned Whirlpool and has not had his calls returned to buy the part needed. Why is this. I need my oven, why is Whirlpool making it so hard for me to have it repaired.

I Purchased a Whirlpool ceramic top self-cleaning oven & side-by-side refrigerator from Sears. I just want to share my experience. I do not have the exact year I purchased them. Too bad I was not aware of this site but after a year with the refrigerator I knew I would not buy another side-by-side and not a Whirlpool. The refrigerator motor runs too loud, the ice maker was forever stopping even during the summer. If you cleared the ice jams it would not reset for hours. The ice maker was replaced under warranty but it still jams; however now when you clear the ice from the trays it produces ice quickly.The temperature in the oven seems to be off now. I purchased a oven thermometer and to verify the temp and they are never the same. But my major concern now is the self cleaning feature. The front door is Yellow and unsightly from the self cleaning cycle. As I sit here typing, I hope the oven does not start a fire it is very hot. This is the last time I intend to use the self cleaning cycle again because I feel it should not be this hot. The ceramic top is hot enough to burn if you touch it. Strangely I checked the oven storage drawer and metal pans in them were okay. Cabinets beside the oven were just a little warm. But This customer will not purchase Whirlpool again.

Its supposed to be energy efficient yet it takes AT LEAST two times as long to get one load done, regardless of size or cycle preference! Now laundry takes all day! Literally! And why is there a lid lockout? Did someone accidentally fall in? If I drop something after Ive pushed start, I have to wait until the machine unlocks the lid. Why? This seems counterproductive. Its a top loader!

I purchased a Whirlpool Water Heater BFG1J5040T3NOV from Lowe’s and have had numerous problems. The biggest issue is having to replace the thermocouple three times. It works fine for about a year then I need to replace it again. This is tiresome and wasteful and Whirlpool should be ashamed. As a company that once had a high reputation, this is sad. I would not recommend buying anything from them, especially their water heaters. After repairing this one, again, I will look elsewhere for the next one.

Three days ago my washer Whirlpool Caballero has made a loud jet noise sound while spinning. While researching for a repair Ive noticed many complaints about this type of washer. Is there any resources that will help me get this repaired?

I bought this washer less than 2 months ago and I am devastated to say the least as they are not even remotely cheap. Appears that is doesnt come close to using enough water or enough agitation to get even 2 pieces of clothing clean. What good is 5.8cu (largest size tub) if you cant even wash a load sized for non HE washer. I am forced to wash a 1/4 of the amount of clothing now vs my previous standard washer, if I even want half cleaned clothing. I have tried every cycle with no difference.Doesnt use enough water but appears to spend most of the cycle time, filling with water. I know that sounds contradictory, but there isnt really any other way to explain it. Might as well not even have an (agitator), I use that word lightly here, as it does nothing to help clean the clothing inside. Pre-programmed cycles are not enough to do what you need it to do. Because of the pre-programmed cycles, unable to place clothing inside, fill with water, agitate a little and then stop or pause long enough to let contents soak for a while. I really miss being able to do this with my previous Whirlpool washer.It doesnt matter how little or how much detergent you use, the results are always the same, clothing comes out partially dry and dirty. Usually requires 2 or more wash cycles to remotely obtain clean items. Most items never even go under the water, no matter how much water it decides to fill with. I am so disappointed with Whirlpool with this fiasco they call a washer, with their name on it and they should be also. I have never owned any other brand than Whirlpool, so I didnt hesitate to buy this set, as I had wanted them for several years and finally made the decision to purchase and what a mistake this was. Will never make this mistake again. Whirlpool needs to correct this for every customer that has purchased these washers or risk ruining their reputation.

This is the second time since I have had the fridge in September 2011. I had to have a new compressor installed about two months ago, and now, it is doing the same thing again. I had lost all my food before and its happening again. Last time, it took over three weeks before the fridge got fixed.

We too have nothing but problems with our supposedly top of the line convection/microwave oven. Purchased in 2010 in February for new kitchen. From start, original microwave installed did not work, would not cook or heat. Dealer replaced. One year later, same problem, but now out of warranty. Had to pay labor, costs, and parts to get fixed. Fast forward 13 months, again magnetron needs replaced, microwave will not work. What a hunk of junk for our money. I will never buy any Whirlpool appliances again, and I will tell everyone I know the same. When you call customer service, they are nice but only say “too bad, out of warranty”. What a joke for a major appliance company to tell customers. It is obvious that this microwave is faulty from the get go, and they just keep on making them the same way and not trying to fix the problem.

I bought a new Whirlpool gas hot water 40 gal tank from Lowes. I Installed it, but the pilot light would not light. So Cal Gas Co came out and said they did not like the new design, but that was how they were now making them. Gas is shot out from a pipe into the tank, however its fairly open. The pilot ignitor is similar to the one on barbarques that often do not last. You cannot get to it to light it manually. Several calls were made to Whirlpool and they sent a repair man out to fix it. You can imagine buying a new hot water heater and having it work part time. The repair man explained that the unit needed a new thermopile, but he could not put one on until whirlpool authorized it, which they would not. After a rather heated conversation with whirlpool they agreed to FedEx a part overnight. Of course the repairman could not wait for me to call and had to come back again. The pilot light still does not stay lit, and Whirlpool now wants to talk about how the tank is vented. This has nothing to do with the pilot light, nor did putting in a new 1/2 gas line and valve as per Whirlpools request. Whirlpool has a problem and they refuse to acknowledge it. However, it is Lowes that chose to buy from whirlpool and they do little if anything to stand behind their product and gain consumer confidence. My suggestion would be dont buy whirlpool, and shop at Home Depot.

I purchased a Whirlpool upright freezer from Sears 17 months ago and it stopped working. I find the warranty is only 12 months. I contacted Whirlpool and they left a message on my answering machine that they would not be allocating any funds for the repair of this 17 month old freezer. I spent in excess of $600.00 and I am highly disappointed. I would never buy another Whirlpool anything.

After having my Whirlpool side by side refrigerator ice maker replaced 4 TIMES in 10 years, I finally found a permanent fix for it: an Igloo counter top ice maker for around half the price of a replacement Whirlpool ice maker. Unlike the Whirlpool ice maker, it makes ice. I promptly removed the Whirlpool ice maker FOR THE LAST TIME, and sent it to the dump, where it belongs. Goodbye Whirlpool! If that is the best you can produce, you will not receive any more of my hard earned money!

Purchased this machine in Jan 2012. From the start, dark clothes came out with white streaks on them. Thought I was doing something wrong - kept using machine. Then started noticing my whites coming out looking very dingy, light tan stains on them. Called Whirlpool and was told to use Affresh tablets to CLEAN my washer - why should you have to clean a washing machine?Several weeks ago noticed machine getting very loud during spin cycles - and I mean loud! Sounds like a jet engine taking off in my basement. Called repairman - he listened to my machine and said noise is the bearings, seal not fitting properly around bearings and the grease for bearings is slowly leaking out into my wash cycles. Explains the dingy whites and spots on darks. Said he just worked on a Cabrio with same issue - had to rebuild seal and bearings - about a $450 job. After reading all these reviews, decided not to attempt to fix this machine. Going to scrap it and start over. $900 for 3 yrs of an inadequate washing machine!! Whirlpool should be made accountable for this inadequate product to all of us consumers who threw away hard-earned money. Reading up on the Speed Queen agitator model. Lots of good reviews. Think I will go back to the old tried and true way of washing clothes.

For the last 5 years, 3 Whirlpool dishwashers. For these years been tracking to see how long they will work, but it seem like they are not build to satisfy the customer. Many telephone calls to service, but they will use the same lines, Nothing we can do... your extended warranty expired. From now on will look for a different brand.

I bought a water heater in 2008 from Lowes department store. The heater would continually go out causing no hot water. The company had sent several technical repair men out to resolve this problem, and still the problem remains. The Technical Support requested that they will pay for the part and I could install it, not knowing if I am able to do such a job. The technicians who were sent to my home were not able to do the job. How do they expect me to do the job without proper experience? Whirlpool products are not reliable nor is their maintenance contract. Stay away from this company.

Our countertop Whirlpool microwave oven is just over two years old and one of the led lights in the clock display just went out. The push-button opening mechanism is very hard to work and quite loud when the door is shut. When the timer is set but the start button is not activated for a few minutes, the door warning goes on and you have to reset the timer. There are five beeps that indicate when cooking is done and they continue even when the door is opened. The only way to stop them is to push the stop button and there is no way to adjust the noise level or number of beeps.

I have read the reviews and agree with all negative comments. There is no point in investing in a high efficiency machine when I have to rewash many dark items several times in spite of always adding the extra rinse cycle. The clothes appear cleaner if I do not add liquid fabric softener, but as I prefer to use my clothes line when possible, I am unable to use fabric softener. Also, although it is supposed to be a high capacity machine, I only fill the tub about one third of its capacity, hoping this will increase the cleanliness of your clothes. It doesnt seem to help.I have contacted Whirlpool several times and the final suggestion was that pay for a technicians visit, approx. $100, plus extra for repairs. I have decided not to throw good money after bad and to buy another brand of washer. This is the WORST appliance I have ever owned even though it is supposedly high-end. PLEASE do not buy a Whirlpool appliance. If the Cabrio washing machine is an indication of the quality of their appliances, you will be wasting your money.

WRF993FIFM00 refrigerator is a LEMON - I bought my $3000 refrigerator just after Christmas. In seven months, it has failed three times and I have been without a refrigerator for a cumulative 7 weeks so far. Each time it failed, I lost all my food, (but not until after wed been eating compromised food). If you buy a fridge, I strongly recommend getting a thermometer, because we learned the hard way that these Whirlpool units can just stop cooling properly and you wont necessarily notice that it is above the FDAs recommendations for food storage. Anyway, after each call they will make an appointment a week or two out for a tech to come out, who then orders the parts that take weeks to come in. Now, my third service call in and the SAME PARTS have failed again and I am again without any refrigeration and they have no idea when the parts will be in. This has been an awful experience, and Whirlpool could not care less. DONT buy their products, under any of their names. IT IS TIME FOR A CLASS ACTION LAWSUIT. Too many folks have spent a lot of money and have been burned by Whirlpool, not to mention becoming ill from improperly chilled food!

On Dec 18, 2015, my hot water heater located in my garage started spewing water out into my garage, driveway, and into the street. I called Lowes, whom I purchased the water heater in Jan 2011, in which it was still under warranty. I was told to call (Whirlpool) 877 817 6750, the order was placed for a gas shut out valve after going through a check system. I was then given the names of two local preferred technicians to repair water heater, whom was not available. The representative from Whirlpool (American water heater) told me I can get the plumber of my choice, authorization number was given. I had to call the (Whirlpool) (American Water Heater) back and was told the part was ordered 2 times. The first part will come on Dec 19, 2015 by UPS, and that the second part will come on Dec 21 by UPS, that a prepackaged label for return will be attached, and to tape the 2 boxes together to send back to the company--one box with the old part, and one box with the new. So, I sent the boxes to an address in Junction City, Tn. But I was not sent prepaid label, so I kept by word and spent $14. I will not be reimbursed according to American Water in which I followed their directions to a tee. So the walk away, the customer is always wrong, staff is not being trained the right way, and as a customer I am out of money and making adjustments to the way of customer service. No service. Just a waste of time, effort, and money.

As long as Whirlpool continues to use JB Hunt for delivery and installation service of their products, I would stay away from ordering. JB Hunt visited my home 3 times, and each time left with the dishwasher as they arrived without the appropriate tools to perform a basic installation. Whirlpool also sent 2 damaged dishwashers that could not be installed. Buyer beware.

We Purchased our KitchenAid refrigerator from Home Depot. After 1 week we had issues with the ice maker, water dispenser and lights going on and off randomly. Technician comes 5 days later, he half way fixes it and discovers we need to order a part. The part took over a week to get and by the time he shows up to fix the refrigerator, it has now been TWO WEEKS with out our $4,000 refrigerator not working properly. Well, after trying to replace the part and spending 45 minutes on the phone with some engineer, it still wasn’t fixed. He Says to us “hey good news youre getting a new refrigerator”. Good news my **. It’s now been THREE weeks and it turns out the new one isn’t coming for another week. Customer serves reps. are really good at apologizing for the inconvenience but Whirlpool has Done NOTHING to composite us. DO NOT BUY WHIRLPOOL.

I have automatic Whirlpool washing machine since 3 1/2 years I am using. Now 2 times electronic board came problem so how many times can change like this? Why they are manufacturing if they cannot solve this problems? Should not sell in the market. This all not coming free and need to struggle. Whirlpool products all very bad appliances.

Purchased a Whirlpool double oven (WGE745COFH) in September 2018. It is now May 2019. After 5 service technicians verified the erratic temperature fluctuations in the ovens, Whirlpool insists that a +25 degree to -25 degree fluctuation in a heating cycle is normal. The motherboard was changed 3 times, and the sensors were changed 3 times, including hard-wiring the last set of sensors. I called Whirlpool and customer service says that is normal. Ever tried baking at a 350 degree setting that fluctuates from 375 degrees down to 312 degrees while trying to maintain a 350 degree setting? I understand there has to be some fluctuation, but either it took a lot of extra time or burned my food consistently. Ridiculous.So, with the help of wonderful people at Lowes (where I purchased the double oven) Whirlpool is refunding my money and Lowes has taken back the slide-in double oven. In my quest to replace it, multiple appliance sellers have told me that all the new ovens having motherboards and sensors have big fluctuations in the oven heating cycles. I find that unacceptable. My husband and other family members have worked daily in an industry where temperatures were critical. They used ovens that could maintain temperature within 5 degrees of set temperature with analog controls. The home consumers are being ripped off with cheap, sub-standard parts making throw away appliances and getting away with it. What do I buy? Havent figured that out yet, but have purchased a countertop toaster oven that bakes beautifully.

I purchased a Whirlpool water heater about 9 months ago. The thermocouple went out and was replaced, but about three to four months went out again. Very disgusting.

At after 4 years of use, my double door refrigerator is giving cooling problem. Upper refrigerator part has excessive cooling and lower part has no cooling... after complaints in customer care, engineer was sent who changed the part that regulates auto cut... it gets blocked by ice so cooling air is not reaching lower part. Once changed exactly after 5 days same problem started... In spite of complaints no one came to check for good 2 wks. After long fight, it was defective board that was changed again. After 3 days same problem again, board was changed... Now after 2 and half month same problem. And now today service center has replied that engineer will be sent after one week.

My Whirlpool dishwasher is used 2-3 times per week. The interior has more than adequate space for a full load of pots, plates and utensils. A normal cycle is used and the washer is essentially very quiet. Dishes/glassware always come out spotless and squeaky clean.

This machine is JUNK and in need of a recall!! DO NOT BUY!!! This was purchased at Lowes for nearly $800 a couple of years ago and what a waste of money. During the first year, they had to send out a tech that told me he was not familiar with top loaders and was not sure why the clothes were not getting clean, nor why they came out with a white residue on the dark clothes. We used the machine cleaner - which the cycles take nearly an hour (how is that efficient?), put in a load of dark clothes WITH NO SOAP and guess what? Then he had me dump in a gallon of vinegar to clean the tub and the wall of the washer and repeated the process and guess what? He informed me that it was just lint. Well, after several visits and using a suggested pin drop of soap, the problem remained. I finally asked him if he was so sure it was lint and not soap residue, would he be willing to taste the lint? It was soap.Obviously after an hour of washing in the efficient washer, the clothes are not getting rinsed. I know this because in just putting in less than ten dark t-shirts, they came out dry!!! He informed me that since he was a contractor for Whirlpool, he was not allowed to continue to come back as he resolved the problem that I was using too much soap! Well, that is only part of the problem. This piece of crap leaks. We not only have a water softener, but a household filter system. In just the last three months, we have replaced the hoses as they are corroding. We were informed by Lowes that the hoses that came with the washers were from China and that they have been replacing them with US made hoses to the customers at no charge due to the amount of returns. Well, those too have been corroding and now I once again have water on the floor.It cost $1.75 to take my clothes to the Laundromat, 26 minutes to wash and ten minutes to get there and back. That is what I have been doing, and using my 23 year old dryer when I get home. It is a shame that the company is not responding to an obvious problem. I only wash two loads in a week - not like I am beating the thing to death with numerous loads or heavy loads. I will not recommend, in fact, I BEG you not to spend your hard earned money on this junk. Buy a $200 washer and if it too craps out in three, four or five years... you are still ahead. You will even save money on headache medication and save your sanity.

I am writing this review because I have been working with Whirlpool regarding our Cabrio washer for the last 9 months. Ever since we got this washer, it leaves a stain on our clothes, especially dark cottons. It looks like a grease stain. The machine is still under warranty (though we did purchase the 5 year warranty), and we have had the technicians out 3 times to figure out the problem and fix it. They even had another company come out to do a second opinion. They are stating that the machine is functioning and therefore there is nothing they can do for me. All of the tests the technicians do come out normal, and therefore the machine is functioning, never mind that it still leaves stains on many of our clothes on a regular basis.I spoke with someone yesterday who was unable to help, stating there was nothing they could do. So, I asked for her superior, he stated that it is functioning properly, and that I should take the advice of one of the technicians who suggested I mix the soap with water beforehand because he is pretty certain it is soap residue (though he admitted I dont use too much when I showed him how much I use). Never mind the fact that if I have to do something more than the directions state, it isnt working properly, we have already done this and it doesnt stop the residue from happening. He still just continued to say that is what the technician said would help so that is what Im supposed to do.So, I asked for his manager. I am currently waiting for them to call me back. I am hoping they will do the right thing and just exchange it for a different washing machine, one that will work. I dont care what kind, whether its brand new or not, I just want a washing machine that actually cleans my clothes instead of leaving a residue on them.We do agree with the technician that said it was soap residue. We have a picture of a pile of dry soap in the dispenser (which the first technician told me to switch to) after the washer had finished its cycle. The washer doesnt have enough water mix with the soap to keep it from leaving a residue on the clothes. And, the residue doesnt just wash off if I wash it again (which shouldnt need to be done with a washer that is less than a year old anyway). It is a permanent stain unless we scrub it with Lestoil - an oil remover. But, that takes time and it needs to be washed twice to get the Lestoil scent out, which then gives it the chance to get new stains from the washer! Its an endless cycle. Needless to say, I have NOT been impressed with this washer.

We saw water all over my wood floor and traced it to the lower freezer unit of my 15-month old refrigerator/freezer. We had to call a repairman which traced the problem to a frozen defrost. He put in a new thermometer at the tune of $200 and now we have to deal with a wood floor problem on top of it. I purchased because Whirlpool was always known to be a quality product. I wont make that mistake again.

I stumbled across this site while browsing the Net, looking for a way to deal with the same situation I now know you all have been struggling with: Whirlpool Washing Machine! I wonder: Is NASA still accepting volunteers for their living on Mars experiment? Id rather beat my clothes on a rock than touch that POS Whirlpool that has me back on tranquilizers! Mine was purchased about 2 years ago when I was in bad health and my son was handling my affairs. I could tell - just by listening - there was something very wrong with it, from the first load my son attempted to wash. It would start and stop, restart, restop, ad infinitum and made a terrible racket. I told him nobody would intentionally make a machine like that--something had to be wrong with it but he assured me that he had checked both with the store that sold it and he also read the manual. He had a hard time accepting but we thought maybe this was because it was new and would settle down after some use; after all, the store (Best Buy) assured him the sound was normal for this particular machine. However, the weird sounds did NOT lessen nor stop, nor did the starts and stops. Little did we know, this was just the tip of the iceberg! We have encountered/suffered through every nasty performance detailed here: low water, wont spin, leaves clothes soaking wet, wont spin out excess water, lid locks (grrrrrr), it cant seem to switch from one procedure to the next; there is nothing washing the dirt out of the clothes--they just sit in the water and soak(?), then the water is released. Clothes come out with stains still on, so wet that the water must be wrung out of them! Very hard for me with arthritis all through my body! Ive tried countless times to reset machine to Drain & Spin. Ive even waited (yawn) for it to unlock so I can open and then readjust the heavy/wet laundry, trying to make it even all the way around so to avoid an unbalance. But nothing helps. It will start to spin. And then it stops. (wait, wait) Starts to spin again. Stops. (wait, wait) Starts again, does it a bit longer. (start to relax) Stops. Ive spent HOURS engaged in that kind of mindless, maddening frustration, just trying to wash one small-medium load. (I wash only for one person--myself, now.) My son, who got married and no longer lives with me, said the only way he could manage to struggle through it - and agrees it DOES take an inordinate amount of time--for just ONE load, he has to put the settings so that it washes in Deep Water even if small load. He sets Rinse, to 2 Rinses. He sets it to Soak even if the soil is light. Even then, it still makes noises, starts and stops, has to be adjusted several times during Drain & Spin. Last but not least, the noxious odor: OMG! I left one batch of laundry in the machine, with the lid open, as it was very late so figured Id dry them next morning. Some hours later when I went back to shake them out and put in clothes dryer, they smelled so awful, I had to wash them all over again! In fact, Ive had to follow my sons admonition to leave the lid up AT ALL TIMES unless actually washing in order to keep down the stink. I washed my last load with Baking Soda added to wash cycle in an attempt to lessen the odor and get laundry cleaner. Someone here wrote - in their review - that there should be a Class Action (Law) Suit filed against Whirlpool. I AGREE!!! And I want to opt IN on it. There are several law firms that advertise on t.v. that specialize in Class Actions. It would take some time and paperwork but will not cost us anything unless we win the case. Then the law firm gets a percentage. I am willing to work with one more others here who truly want to settle out this problem. I cant believe 2,000 (and thats only here), people are willing to eat hundreds, thousands of dollars of worthless, mind-gripping, rubble such as we have spent our hard-earned money. Other manufacturers recall their defective merchandise and/or replace it, or make arrangements with the retail stores who carry it to make amends, free repairs, whatever it takes to make dissatisfied, disenfranchised customers, whole. We paid for these demons from hell and we deserve to get an equivalent in merchandise (that works properly) or services. That is how it is done here in the U.S. For the life of me, I just cant comprehend why Whirlpool has been allowed to continue selling this junk--why no entity or person or lawsuit has stopped them! As I said, I am willing to work with a core group who is serious about filing a Class Action (Law) Suit against Whirlpool. It may be that the retail stores would be included as well; however, that is a matter best left to the discretion of whichever law firm we select to represent us. For those of you here who do NOT wish to be included, do not worry; you are not being pushed into anything. The way Class Actions work, you have the choice to opt IN (be included to receive your pro-rata share of what is collected). Or you are completely free to opt OUT. By opting out, that means you do not wish to be part of the Class Action and therefore, you will not be included nor will you receive any portion of the recompense collected via the Class Action. Just for your information, though: You are allowed, by law, to bring your OWN lawsuit against all or some of the same parties. The most common reason for opting out, is if you have suffered an extra large financial loss and prefer to file your own suit in order to collect ALL recompense; whereas, sometimes - in a Class Action - the individual plaintiffs may not recoup the total amount they feel they have lost. If you DO decide to opt out and go on your own, realize you will be fully responsible for lawyer fees (although you CAN add them into the balance you are seeking in your suit. Settlement of your claim may or may not include lawyers fees.) Good Luck to all. To those who wish to file a Class Action with some of the rest of us, please contact me if you want me as part of the core group of plaintiffs.

Bought fridge in 2010, I am about to replace the icemaker for the 2nd time at a cost of over $300 each time by a Whirlpool authorized repair tech. No kids in the house and very limited use of icemaker. Motor keeps burning out because of the design flaw per the tech. Very poor design for a $1,500 fridge. Due to these issues I do not intend on purchasing Whirlpool products in the future.

My 3 year old Whirlpool refrigerator costing $1285.86, needs a new motor and fan. Of course it died right after a trip to the grocery store. On a week temperatures were well into the 90 degree range. Needless to say my groceries had to be thrown out at a cost of an additional $250. How convenient that the refrigerator died 2 months after the 3 year protection plan ran out. I just spent $182.94 to have a repair person come and check out the refrigerator. I will need to spend another $170.00-$200.00 for the motor and fan once the parts come in, which can take up to another 10 days. Had to go out and buy a backup refrigerator that cost $562.38. Also had an issue with this refrigerator after a year and half with ice building up in the bottom of the freezer. Luckily we had the protection plan at that time, otherwise that would have cost us $157.58. The refrigerator is stainless steel and I have a terrible time keeping the rust off the front of it. At this point l guess all I can do is warn everyone I know to never buy a Whirlpool appliance if this is an indication of how they manufacture their products. So very disgusted with this refrigerator! Sad my old Frigidaire was close to 30 years old when the freezer just wasnt freezing well anymore. Thats why my new backup refrigerator is a Frigidaire and not a Whirlpool.

Piece of crap. We built home 2 years ago and have all gold series appliances! They are all CRAP. Wish we would’ve upgraded to KitchenAid. Dishwasher won’t wash, microwave has hot spots and has to be unplugged and plugged back in often to work. Freezer side of the refrigerator will stop making ice because it freezes up often! NEVER buy Whirlpool!

We purchased the WRX988SIBM00, delivered 6-26-14. Immediately upon plugging it in, we noticed a seemingly loud hum to it. Thought maybe it would go away once the fridge cooled off, but the hum continues. SO sad because I love the features.

Terrible wash machine. Some clothes come out having never even gotten wet. The spin cycle ties your clothes in knots so bad you have to machine dry them because the wrinkles are ridiculous. I’m all for saving water but if your clothes don’t get wet, how are they going to get clean? Also can’t do just a rinse and spin cycle. I would rate zero stars if I could. Don’t waste your money on this junk! Wish I could buy an old fashioned Maytag. Those washers were the best!

We have had our range for over one year. The main problem is that the large burners are in the front and the small burners are in the back. This means that when we are using the two front burners we cannot access the rear burners safely. (What country provided the engineering design for this?) One minor problem is that we cannot get used to the burner control arrangement. The outside controls control the front burners and the inside controls control the back burners. Our old range was the right control for the back burner and the left was for the front burner. Another small problem is that there is no back to the pan drawer. So, with the drawer full if a pan move when the drawer is shut it will be scraped off the drawer and fall into the back and becomes hard to reach to remove.

I have been a dedicated Whirlpool customer for 50 years. I purchased my new, Cabrio washer and dryer in 2011. The dryer works fine. The washer does not. It ties everything in knots. Most everything comes out in one large, wrinkled lump. When washing sheets, it wraps the whole load in a soaking wet, fitted sheet bubble. You cannot wash one item by itself, because it will become unbalanced and shutdown. I will say that I havent had any repairs yet, but I have a feeling, its only a matter of time. I have decided to buy a new washer, but it will not be a Whirlpool.

WRF993FIFM00 - HORRIBLE. I could not believe the reviews for this fridge... so I went ahead and bought it - WHAT A MISTAKE - service guy is at my house right now - fourth time in three months... fridge froze up and all my food has gone bad.

I was going to write a negative review after our Whirlpool stove oven stopped working. We only had it for three years. Technician’s visit today was $70 for the information that we would be better off buying a new one because the motherboard is gone. However, after reading all the horror stories which are already here, I realize that we are relatively lucky - at least, our stove worked for 3 years... Still very disappointed and unhappy. No more Whirlpool products!

I just bought my stove four years ago. Every time I want to bake something, I have to run a fan on my stove because it overheats and shows an F2 error message. I then have to unplug it, leave it unplugged for 20 or so minutes. Once it cools down, I can plug it back in and use it. I have to go through this every time I use the oven. Its annoying and I lose a lot of food because sometimes, it just wont work. Idk what to do!

Works fast and quietly. Easy to set up. Get the geek squad coverage and clean the filter at least monthly.

I bought my Whirlpool dishwasher, model #WDF560SAFMO in Nov 2016 with a 2 year extended warranty. In Jan. 2021 it quit working, was told by repairman that the dishwasher needed a new pump. Of course, it is no longer under warranty. To replace the pump will cost almost as much as a new dishwasher.

I purchase Whirlpool refrigerator. After a year it has done nothing but give me problems. Thank God I purchase insurance for repairs. I had the refrigerator fix over 3 times. First the water and ice wasnt working so the filter had to be change. Then the ice was made and my refrigerator start leaking. The repair guy stated the fan and something else is not working. I am a single mother struggling and to spend over a 1000 dollars for a refrigerator that does nothing but give me trouble. I am totally unhappy with this product.

What a POS. Havent even used the thing to cook a meal yet and already some chunk of metal fell out from the port at the top left inside the oven (behind the vent). It was clearly cheap pot metal. What else is this thing made out of?

We purchased a new home April 2013. All our appliances were new Whirlpool stainless. Looked nice. After almost a year our microwave started acting improperly. Beeping, changing screens, not working when buttons pushed. Then the micro wave had a melt down and caused the glass try to break, parts to melt and caught fire internally melting plastic. Notified Whirlpool and they sent out individuals to repair. After several weeks the repair was completed and we were advised that they did not understand why this would or could happen. We should be fine now. Well we are now again having this unit beeping, changing screens, not working when tried, and when entering numbers, number and time are not what was trying to be entered. This unit my wife says is possessed and she wont use it. She fears it will burn the house down. It is Velos model TR 2 24 11000 serial number. It now beeps and changes with door open as I read the serial number.

I recently purchased a Whirlpool Gold Edition double range. After a couple of uses, the top oven thermostat went on the blink. I sat the thermostat to preheat. After 20 mins. and a call to the warranty department, the oven never reached the desired temperature. The warranty department sent a repair person who could find nothing wrong with the stove. I called Lowes and told them I couldnt trust the oven not to do it again (after several times of it happening and resetting the circuit breaker). This would be a disaster if it happened during the holidays when I cook for 20 or more people. Lowes manager said they wanted me to feel comfortable so they replaced the entire range. GUESS WHAT... 2 weeks after having the new one... same problem. I set the thermostat to 400 degrees and when it got to 390, I saw the light blinking. Waiting 10 more mins, nothing changed. I hit the cancel button, reset the bake... the thermostat, when I turned it back on, showed 365... What the heck! I didnt open the oven door. Whirlpool ranges are a piece of crap. I am calling Lowes again tomorrow to return and advise them to stop selling the junk. Dont blame Lowes... They do the best they can with the crap they sell.

I like my machine even though there is no agitator. It is a top loader so it does not smell. It is a water saver which, when I first got it, I thought that it could never clean the clothes in that small amt of water...but it does clean the clothes very well.

I am really disappointed because I purchased the refrigerator and now the dispenser display assembly is not working and the company does not have the replacement part to fix it. So now do I have to buy a new one???

Similar to what I am reading below and on other sites, my hot water heater stopped working. I spent about an hour trying to relight the pilot light, which apparently you cant do with this model because it breaks. My first thought and action was to call a plumber to come fix it. When he arrived he said it was reverse thread and that I would have to call Lowes to get a replacement part. When I called Lowes they said they would call Whirlpool and then give me a call back. Two days later I still havent heard back or taken a shower; I am going to the gym tonight. Finally, I got online and called the 800-number and am being sent a part to arrive tomorrow. I asked to be reimbursed for the cost of the plumber since they obviously knew they had a problem (they assumed why I was calling the warranty line) and redesigned the issue with a voluntary recall. Whirlpool, please make this right. I know you license your name to American but it is still your name and brand reputation.

I bought a pair of Whirlpool front loading washing machine and dryer on May 23, 2011. The Duet Steam washer model is WFW9640XW, dryer is WED9470WW. Their high retail price was $1125 each. I did not pay this for them. I thought I got a great buy at Lowes for the price I paid, plus their 4-year extended warranty. Whirlpool used to be a very high-end appliance manufacturing company. Now, all they put out the back door is junk. I would advise not to buy Whirlpool front end anything. My washing machine started making noise about 2 weeks before I reported it to both Lowes and Whirlpool. The noise sounded like bearing not being lubricated, which that is what it ended up being.The noise got so loud that even with all my very expensive electronics (my home entertainment ctr equipment) I could not hear the TV which goes through an expensive Yamaha AV Receiver and those expensive Infinity speakers 7 channel system. The main bearing for the wash drum assembly was bad. After two emails and several phone calls to both Lowes and Whirlpool, Whirlpool was going to send the so-called re-engineered drum assembly. The style I have is 3 parts; the new one according to Whirlpool is one part, but if they put the same bearing in, youre going to end up with the same problem in another year. I live in a condo of just over 920 sq. ft. so really there is no room to repair them in my home, but that is what they are going to do. I will be getting the new drum assembly delivered to my condo and have the repair company doing this dirty job in the middle of my living room.Living in a condo, I have a small utility closet next to the kitchen where the furnace, hot water tank, and washer and dryer are. The closet needs to have some areas cut out with and installed two small hinged doors on each side, so if anything ever needs to be repaired or replaced, there would be a little bit more room to move items in or out. The problem getting the washer out is getting the dryer moved so you can disconnect the electrical plug, cold water hose for the steam, plus the vent hose. First, you have to get to the water valves which are very hard to reach. Because of the way cluster housing is made, they squeeze things into very small holes like the faucets and drain hose are located. I was asked by the repair person if I could help him lift these items out of the closet. I have had 7 fusion back operations and #7 left me in constant pain that I take a narcotic drug for pain daily. So, I called Whirlpool back and said the repair people were only going to send a tech. I was told that it is a two-man job: one tech and one helper. So Lowes needs to authorize two people since Whirlpool is sending the new drum assembly for free. I wish I could have gotten a new washing machine with the so-called re-engineered drum assembly. I am still probably going to have to squeeze between the bulkhead (wall) and the washer and dryer to disconnect everything since I am a small person. If I wasnt retired, I would have bought a different brand front loading washer and dryer, probably Bosch and took the loss on these piles of Junk. I love my country and do my very best even as hard as it is in this day and age to buy US. I served my country in the US Navy during the Vietnam War, just to see the civilians willfully buy Asian everything. So now, we have 4 Asian nations that own this country. I dont know why Whirlpool changed from a company that you could trust their products to a company that doesnt give a damn what they put out the back door. These companies still havent gotten the clue why folks buy goods from other countries. I think they need to open their eyes, but I guess with Whirlpool still being a company that is selling a very large number of appliances and making money off of us, suckers, they dont need to change. The only way they are going to change is if folks stop buying their junk.

This machine cannot handle washing jeans, towels, blankets, pillows or anything bulky or very small loads. The load becomes ul unbalanced almost every time I try to wash a load. It has never gotten things very clean.

I purchased a Whirlpool Cabrio Washer in May of 2009. I do laundry for only 3 adults, so I never run more than 3-4 loads a week. It constantly is off-balance when spinning and requires positioning the load again several times before it will continue its cycle. Now 5 to 8 minutes into it filling with water, it stops filling and beeps, and code F shows up on the screen. Also, during the spin cycles, it is very loud and fast. It sounds like it is about to take off anytime. I called customer service to no avail. They just wanted me to schedule a repairman to come out and fix it at my expense. Now, I know why they only give a one-year warranty - they know it will last one year but not much longer. Im from a generation of people that is used to appliances lasting 10 - 14 years and the company stood behind their products and didnt ask you to buy an expensive extended warranty for the 2nd year and so on. If inferior products were not manufactured, there would be no need for an extended warranty. Anyway, Im not going to put any money (I was quoted a $129 charge by Whirlpools service department just for the diagnosis of the problem which didnt include the labor or parts costs.) into a washer that will probably continue to have problems and become a money pit. Consequently, I will never buy nor recommend anyone buy Whirlpool appliances. It would get quite expensive buying a new washer every 3 years or buying the extended warranty plan. The matching dryer had no major problems, but a couple of years ago, I had to have the door changed from opening from right to left to opening from left to right because the door catch broke on the right side. Hopefully, nothing else will go wrong with it in the near future.