My landlord purchased a new Amana washer (NTW4605EW0) Labor Day weekend 2015. It started having issues in the spring, so we went through the process of utilizing the manufacturers warranty. Apparently, Amana, part of Whirlpool, requires 5 attempts at repairing the machines before replacing. Okay, so starting in June 2016, we arranged service appointments 5 times and replaced 1 part, then another, 4 times. Clearly, that part is defunct. Right? Fast forward to September and then into October. Get a new washer, and not the one I preferred. We got the Whirlpool WTW4816FW1. Before the installers leave, we are having the SAME issue. Stops midcycle, doesnt finish cycle, sometimes stops while filling, or while full, or kid wash, or mid drain... But now with the new washer, the drain and spin cycle thinks it should FILL instead of drain... and Whirlpool said they would get someone out the next day, a promise they cannot keep because they dont supply the repair guy, they source with local companies. So, the company ordered 3 parts... That could be the problem. And 4 days later, 2 parts are on freaking BACK ORDER. Parts arrive. All new parts replaced. Machine still doesnt work. Outlet tested by us and them and it is fine. The techs think there is some kind of RF interference. Turn off sensor light, which is on the same wall, unplug power to wifi router (which outdates the washer). Still, doesnt work.I have spent half my week, every week, since June, restarting my washer, unplugging the damn thing, waiting, and waiting, trying again and again and again to wash 2 loads of laundry a week... Literally takes a week until the damn thing does its job. Whirlpool is sent us a replacement washer. Can you guess what happened the first time we started it? SAME ISSUE. Cycle will not complete. Sometimes it dies before it even fills. Sometimes it dies while filling. Sometimes, it will fill and fill and drain and fill and fill and drain and... never stop filling. Or, the fun one, the drain and spin cycle thinks it is suppose to fill. Continuously. And then, suddenly, after unplugging it for 1 hr, or 24, or 72 hrs, it will work fine for 1-7 cycles. Nothing is consistent except that it doesnt work consistently. HAS ANYONE HAD THIS MUCH TROUBLE???

Purchased a new Whirlpool washer and dryer at HH Gregg about 4 months ago. We complained to HH Gregg that the low water washer wasnt working correctly. It will only get about an inch of water in it causing buttons to be torn off... just beating up wet clothes. HH Gregg told us to try a few things. When we went back to HH Gregg with the same complaints they told us it was too late and call Whirlpool. Serviceman came out and said everything was fine with the machine, we just need to load more clothes! We are only 2 people, one of us wear a uniform and needs washed when we may not have a full load. Called Whirlpool to complain again and they said there wasnt anything they would do except send out another service person for a second opinion, which just means taking more time off of work. HH Gregg talked us in to this type of low level washer. We are still making payments on it!!!!

Shortly after the warranty expired my refrigerator started building ice on the floor of the freezer. With the build-up of ice the freezer started leaking on the bottom. Sometimes it gets so bad I have a hard time closing the freezer door properly. The Model# GB9FHDXWS06, Serial# K31505096 of my Whirlpool refrigerator. I do not recommend any Whirlpool product. Do your research before you buy any Whirlpool product.

The side-by-side with the lower freezer was one of my all-time favorite units Ive ever had. The capacity of the interior was expected to be better, particularly the freezer, but it was effective in getting to the items I needed. Storing was good, but the freezer had trays in the upper portion that I could see when looking down, as Im over 6 tall.

We purchase a washer and dryer from Lowes in 2012 and a couple months ago I begin to notice that the Clorox and the softener draining spout is not working. The Clorox side is full of water, and the softener half of the time dont even drain all the way and not happy with that. The washer is beginning to rust on the inside by the dispensers, the lid area and the outside panels. I should have purchase GE. I would not recommend this brand to anyone.

I bought the new Whirlpool aqua clean last year - they guaranteed me at the store it would clean as I explained having a clean oven at all times was extremely important to me. They assured me I would be pleased with the results. I have never disliked an oven as much as I do this one. The tech came to the house and checked the temperature of the oven as I also complained it was baking uneven (the back was overcooked while the front was underbaked) but the temperature was right on so nothing can be done. As far as the cleaning goes all I can get is a new bottom pan for the oven as I have four years of insurance. Not happy as I would like to have a different stove. I WOULD NEVER RECOMMEND THIS OVEN TO ANYONE.

I purchased refrigerator in 2010 through Sears. The freezer door began collapsing (like the air was being sucked out) and Whirlpool sent a replacement. I should have known at that point - they had over 20 in stock instead of making it to order with a several week wait as the rep expected. I complained again (out of warranty for the refrigerator, but less than a year for the replacement door) and was given the too bad, so sad - next question routine. Now the freezer wont hold frozen food. If I turn up the dial, I end up with frozen lettuce, etc. So much for Whirlpool! Im not so much angry at this point as I am talky - at the grocery store to perfect strangers, at church, etc. Im disappointed that Consumers didnt respond - they still rate Whirlpool fairly high - makes me doubt Consumers, too.

I owned the Whirlpool washer for 13 months until it quit. Menards was no help with anything. I am going tomorrow to get to try my luck with Samsung.

Purchased a new Whirlpool Energy Smart 50 gallon water heater from Lowes to replace our existing old one that had gone bad. Never again!! Had it professionally installed by one of Lowes installers. I have no problem with the installer.... the water heater was a piece of junk. From the first day we had sporadic hot water and to get that you had to have a hot water tap turned on full force. If you turned the tap to a lesser flow you got cold water. Couldnt get a hot shower at all. Contacted Whirlpool customer service 4 times by phone and 3 times by email. Horrible !!!! If I had read all the reviews ahead of time I would never have purchased a Whirlpool water heater. Each time contacting their customer service I was informed I had a plumbing problem... probably a cold water line was feeding into my hot water line??? Really??? After living in this house for 20 years all of a sudden I have a cold water line magically connect itself into my main hot water feed? I even set the temperature up as much as it would go. Could easily hold my hand under the hot water without getting burned. Most of their phone reps sounded like they were reading from a check list sheet and no desire to actually listen to what I was telling them. One even sent me a PDF file via email that had nothing to do with the problem I was describing to them. I finally told them after two weeks of this that I couldnt live with this situation and they said Well our technicians are 38 miles from you and we wont send one that far to check it. Asking what I could do they said Id have to hire someone (they werent able to tell me if I should hire a plumber or electrician) and Id have to pay for it and they would reimburse me. Sensing that this might be a fruitless task I resorted to calling the Lowes store where I purchased it and asked their advice. They offered to send out the original installer to check it out and work with Whirlpool over the phone. Like I said, I have no complaints with the installer, he was fast and professional. I stood there while their technician/customer service had him go through a few tests on the unit. All of that proved nothing except in their minds that nothing was wrong with their unit. He got off the phone and told me They refuse to accept any responsibility for the product being bad. I asked him what was I supposed to do. He got on the phone with the manager of the Lowes store and they agreed to swap it out at no charge to me. I of course was very happy but told them after all of this I didnt want another Energy Smart type water heater and that I didnt trust the electronics at all. He agreed to swap it out for a regular type and give me a credit for any difference in cost. Had this all done in one day and am very pleased with Lowes commitment to customer service. The new heater (still a Whirlpool sad to say) appears to be working fine just like my old one did. So much for it being a problem with my plumbing. After reading all the complaints about Whirlpool water heaters, I guess Im not looking forward to much of a life expectancy with this one and Im certainly not even going to attempt to call Whirlpool customer service if I do. This whole thing cost me $700 and as far as Im concerned Ill flush $700 down the toilet before buying another Whirlpool product. I still would love to know how any person with half a brain could tell me I had a plumbing problem when all that was done was removal of an old water heater and replaced with a new one. Thats two pipes people...cold water in, hot water out. I see that there was some type of class action lawsuit filed against Whirlpool. Maybe they need another one filed or forbidden to sell water heaters ever again.

It is in the mid-range of cost and functions. For a mid-range dishwasher, it has many options, sometimes too many. It does not have rinse and hold. I think its cycles run too long; not always energy efficient (i.e. the simplest one uses the most energy).

Even with the hottest water on the most heavy duty setting, regular dinner plates are not cleaned. The flatware holders that are set in the door (instead of free-standing in a rack) do not have adequate holes in the holders and are too far away from the limited jets to get adequate soap and water to cleanse the flatware. Even after rinsing all scraps off the plates and flatware, we find bits of food, gravy, or smudges on the plates and flatware - since its first usage. The manufacturer had the audacity to claim that was normal. Settings include delayed starting, heavy duty versus normal washing, and different types of drying. The heavy duty washing is definitely poor quality, and there seems to be no difference between any of the drying settings. The delayed start is nice. The physical layout of the prongs on the racks and the folding racks do not allow easy fit for most sizes of pots plus plates on the same bottom rack. I cannot put a 1 gallon pot level on the same rack as dinner plates. I must put it beside salad plates. Only small sauce pans fit neatly or cleanly beside dinner plates. Yet the external dimensions of this dishwasher are the same as the competitors standard size. Looks neat and is easy to clean. Also, the exterior does not show scratches. Actually, I cannot see where the exterior has any scratches. The service people were very little help. The Warranty said that after five (5) service calls the unit would be replaced. We made six (6) service calls, but we were told that we did NOT have six because if you called again within 90 days of a call, that was considered the same service call. That requires 450 days minimum to have five (5) qualified service calls, but that warranty was good for only 365 days!

I purchased a Whirlpool French door refrigerator model # gx5fhdxvyo4 in June 2011. Four months ago, ice was forming on the bottom of the freezer. Repair person replaced a clogged plug leading to evaporation tray. Its March 2013 and repair person now has to replace evaporator motor part # W10128551. I contacted Whirlpool and was told the warranty has expired (one year). This repair will be around $175. How can I trust a Whirlpool product in the future?

We purchased this large 4 door refrigerator in December 2018, from Costco in Florida, having in mind with the 2 years Manufacturing warranties and 2 years of Costco warranties above the manufacturing warranties. We didnt expect any problems for the initial 4 years. Up on delivery some parts of the unit was missing, delivery guys said they will make a report for the missing left drawers and the parts. We did not have any manuals how to setup and use. After we called the customer service they send us the operating manual.We encounter several other problems with this unit and the most recent one to our surprise the warning light to change the water filter was on. We hardly using the water from the fridge because of the having monthly spring water delivery service. We called customer service and after explanation of our concern and following their instruction the light was on. Finally we were told that whether or not using the water filter has to be changed every 6 months and send us the additional service warranty contract which is $411.95 for 3 years. We still have 3 years 4 months remaining from our original warranty.

The reason for the call was to find out how to file a claim after replacing the ice maker and paying for it the 3rd time, they were very argumentative and would not listen to me about the design flaw in the wire harness that burns up the motor for the ice maker. I found out about the design flaw from talking to the repairman that replace the ice maker who works for Dick Kearsley Clearfield UT. He told me that Whirlpool knows about the problem for the 22 cubic foot and 25 cubic foot refrigerator and that is why they have 2 different new wire harnesses in the box for replacement of the old wiring harness.

I have tried to contact Whirlpool, email and telephone call. Finally someone called me but Customer Service was poor. I asked her to have a Manager call me, but she never did. They also never responded to my email. We Purchased our new Refrigerator 21 c.f. side by side 2 months ago. The ice maker is driving us crazy. It is very loud. There are white plugs on the 2 bottom corners that make the appliance look extremely cheap. I am not happy with this Refrigerator!

The dishwasher is noisy and the latch which holds the soap, at times sticks. When we think it is done and ready to unload we need to run it again because the latch that holds the soap DID NOT open. Not good.

I have been TRYING replace a damaged panel on a $10,000.00 Jenn-Air refrigerator for over 10 months now!! Whirlpool is the supplier of Jenn-Air - I have probably spent at least 3 HOURS on the phone talking with one rep after another who ASSURES me they will deal with my problem!! Last week I gave my credit card # to the rep - who told me my part was sitting there, waiting for my # to be shipped. When I asked why no one had called me to let me know, especially considering the amount of time I have been waiting - she said she didnt know. One week later, I call AGAIN to find out why my credit card does not show the payment. Only this time to talk to a fellow who says my part is still on backorder, and they used my card # to put a $1.00 charge against it - to hold it for when my part arrives.. BUT has NO IDEA when that may be! I feel Angry, totally discouraged, lied to, and used! I will NEVER purchase any appliances under the Whirlpool affiliate. This is abhorrent customer service - a $10,000.00 appliance and this is how it is dealt with!!! Bad, very bad!!

I had this stove for less than 3 months and the glass top broke after turning on the stove. Now I tried to find out how to purchase a replacement but it cost as much as a new stove....Ughhhh this is so aggravating.

This is our 3rd repair in 13 months and now my 4 and 1/2 year old son and I both suffered bacterial food poisoning on this 3rd round. It has been a complete nightmare. Then we found out until last month, they were completely replacing the entire refrigerator. Then they stopped that and are just replacing the parts again. Now there is a back order of the parts and not to put any food in there or we will get sick again. The repair itself will take 4 hours whenever they get the parts in and another 1/2 day to take off work. We are building a house and have bought the entire gold series line of crap that is sitting in boxes in our garage. NOW WHAT WHIRLPOOL?

Very unhappy with my top load washing machine. I use more water. Can wash fewer clothes and clothes do not come as clean as with my older Whirlpool. This machine needs a SERIOUS AGITATOR. Will not buy another Whirlpool.

Worst customer service I have ever seen. I have been waiting on a part for my dishwasher since before Thanksgiving. I have sat on hold for 2 or more hours. They cannot connect you to a supervisor, you just continue to wait on hold. They cannot give an eta for the part that has supposedly been in production since before Thanksgiving. I get told one thing, then when I call back for an update 2 weeks later that person has no idea what Im talking about. I will tell you one thing, if you do not want a headache, I suggest you buy another product!! I can guarantee, I will let everyone I know and never purchase Whirlpool again if this is not resolved this week! After doing my research, this part should be recalled. It is a big issue with this very expensive dishwasher.

My oven is less than 2 years old. The blue enamel has had cracks for over a year & was told its cosmetic & theres nothing that they can do about that. Now its starting to pop off. I found a few slivers in a vegetable dish! Now I cant even use the top oven because of this! It seems to only affect the bottom of the top oven. I feel that the temp may be getting too hot for the blue enamel which is another safety concern. I have contacted Whirlpool/KitchenAid to be told that if they send out a repair person he would just use a marker on chips. I was told they would give me an employee discount from $3000 to $1800 to replace but I would have to act right away for that price! Really? My oven is only 1 & a half old.When I started researching this problem I am having I found many complaints of people having the same problem! As a consumer I feel so mad & frustrated that they are not doing anything about this since its an ongoing complaint from so many dissatisfied consumers. I do believe it is a safety & health risk now that its showing up in the food that has been cooked in that oven. I would urge anyone thinking of buying a Whirlpool/KitchenAid cobalt blue enamel oven not to! They will not stand behind their product & you will have to replace at your own expense. Shame on you Whirlpool!

The Whirlpool HE H2Low Washer is the worst piece of crap Ive ever wasted my money on! It leaves soap residue on all my dark clothes! DONT WASTE YOUR MONEY! Whirlpool should be ashamed of themselves for continue to sell these pieces of crap!

I purchased a new Whirlpool Cabrio set, in 2009. I bought the top loading washer, and matching dryer. Since 2009, I have had the washer serviced FIVE times. Bearings, water pump, F1, F2, ul codes, and a few other things, I honestly cant remember. I love this capacity. But that is all I love about this machine. Today, the water pump went out again. I have been reading online regarding loose coins making their way into the drain pump, the hose, and other parts of the washer. I am diligent about emptying my pockets, but, obviously, someone in the house is not. There should be a trap for the coins, buttons, and any other debris that passes through, but, clearly there is not, and it appears I am not the only one with this problem. I am so frustrated. I paid almost $3,000.00 for this set. It was my very first brand new set and I have had so many problems with this. With all of the problems and all of the complaints, and so many similar complaints, why is Whirlpool not acknowledging them? Why are they not doing anything about it? Side note, my dryer works fine.

I bought this Cabrio Washing Machine just over a year ago and it never drained water when I was doing towels and bed sheets. Life got in the way, and I managed to run smaller loads in the regular settings. Now, the machine is just over a year old and it will not spin unless I put it on the rinse and spin issue. It takes well over 2 hours to wash a load of laundry. From looking at other reviews, this is a big problem. I would not recommend this washer to anyone. It cost a ton of money and was the worst washing machine I have ever used.

Whirlpool Upright Freezer Model EV205NXTN01 – The freezer door interior plastic panel bows away from freezer cabinet causing door gasket not to seal. The new gasket doesnt help since the groove of the gasket mounts in bows outward with the interior plastic panel in the door. The freezer is 20 months old now and had the door replaced for the same reason at 10 months old. Now, Whirlpool says sorry it’s out of warranty. Guess they want me to buy a new door every year. I wont be buying Whirlpool products anymore as I dont need another boat anchor.

Purchased my Whirlpool dishwasher in 2005 model number GU2500XTPQ3. So it worked for about 10 years and I am fairly happy with that but I have a warning, my control panel shorted out putting out thick black smoke and I was unable to turn off the dishwasher. I had to turn off the switch at the breaker box. If my wife had of been the only one home she would not have known how to turn it off and would have had to call the fire department. I dont know if the short would have led to an actual fire but with that much heat I have to believe it would have. Warning, dont run the dishwasher when no one is home. Hope this helps someone.

The washer has rust under the rim in the inside - also the paint is bubbling and peeling under the rim of the washer. I contacted Whirlpool and was told that is a cosmetic problem. There is no warranty for rust or peeling paint. I will never buy another Whirlpool washer. I paid over $700.00 for this washer and I dont think I should have a rust problem after 5 years.

10 years, no problems with our 25 cubic foot french door Whirlpool refrigerator. Ice maker is a solid performer, with nary an issue. Temperature controls work flawlessly. The black frame looks great in our kitchen with espresso color cabinets.

I purchased this stove online and have been very happy with the features. I am able to use alternate settings based on the size of the Pan/pot. Cook timer, light, variable rack displays, etc. The only negative feedback is the need to add 5-10 minutes more to the temperature, based on the recommended cooking time of your recipe.

Bought the hot water heater, installed it. It leaked from bottom. Whirlpool warranties it. Replace it with new heater. It too leaks. I Google problems with Whirlpool hot water heaters. Found over 1500 complaints.

Whirlpool claims this technology works to clean the oven; however after one month of use and one casserole spill, we attempted 3x to use this system and the cleaning process was a total failure. The gravy spill on the bottom and mild oil residue on the sides from roasted vegetables was the same as before the cleaning cycle was tried. The cleaning kit accessory from the company was a joke. It consisted of 2 sponges and a small scraper! We purchased the slide in model WEE745HOFS. Buyers of any and all Whirlpool products with Aqualift BEWARE... It does not work. We have since replaced the product with a range with the traditional cleaning process system that has worked for decades in most major brands.

The average life of a refrigerator is 11 years. We purchased a Whirlpool convertible refrigerator (Model EL7JWKLMS02, Serial # EWR1339731) on 6/12/04 from the Lowes here in Visalia, CA. The first delivered was DOA and Lowes delivered another. That should have been a warning sign. We have had several problems with the product, as early as 2006. All repairs went through Sierra Appliance & Franks Appliances.We are now in the market of another refrigerator to replace this one. We have had to have freon added now for the third time. Sierra Appliance was unable to find any leak, but each time, the freon was depleted. In addition to the health hazard of having freon leaking into the house, we have had the distinct displeasure of having to deal with food waste, etc. Because of the ongoing problems with this product, we are now facing the reality of purchasing another refrigerator to replace this Whirlpool product.Due to this, I feel it is difficult to consider another Whirlpool product and will question any product to ensure that it is not Whirlpool-related. If there is anything that Whirlpool or Lowes can do at this point, it would be appreciated. Thank you for reviewing this note of dissatisfaction. It appears that we will be shopping for a new refrigerator this weekend unless we hear from Whirlpool. In any event, I would like this recorded as a complaint from a former customer.

Whirlpool Slide-In AquaClean Technology - My beautiful, modern oven is no longer. After 4 tries doing self-cleaning my oven was still dirty. I did have to wipe out the water (although I measured it) before I could take the scraper/sponge provided by Whirlpool to assist in the cleaning. Scraper bent - sponge disintegrated and I still have a dirty oven. Called service. My pleasant service tech informed me the water is only to reach 250 degrees! Really! My dinosaur of a Whirlpool cleaned fabulously! New technology has turned mine into an on your knees, scraping and broiling fool. Fool because I bought into the whole Aqualift Technology. We cannot use any kind of liner, etc. This slide-in may look great but the labor required to keep it that way is beyond this OCD person! So much for my efficient new kitchen. May the engineers who designed this technology be ashamed of this product. It is not even a self-steam cleaner!

We bought a Whirlpool Cabrio in April 2012 and in July 2012, it started giving problems. It wouldnt start. It started humming. We heard money-like jingling noises. It stopped spinning and rinsing clothes. I called for service. No luck with that. So in order to wash, I had to drag the washer to the back door (which ripped up my new floors) hang hose outside for it to finish the load. Well a few months later, that didnt work so the assistant where it was purchased told us to cut the pipe down in the wall. Now we have a big hole in the wall. My floors are ruined and we are out getting another washer. This one is not even a year old. That was a $750 loss.

We just love the hidden icemaker, the outside display for temps, ice, water, external H2O and crushed or cubes, and the LED inside lighting is fantastically bright, the space, moveable shelves, the quiet, the overall efficiency, huge drawers freezer, the wide open doors, the separate temps for vegetables, cheeses, cold cuts, etc. The separate filters in the refrigerator eliminate any smells. Easiest water filter to change we have ever had on any make refrigerator. Over the years, this is the first refrigerator of perhaps 7, we have truly never regretted buying it and frequently comment how happy we are with it!

We purchased a Whirlpool Gold Dishwasher about 8 months ago. Immediately called for service as dishes did not clean after running over 3 hrs. Was told it is operating as designed. I followed all the tips and it still continues to not clean. Plastic wear and cups stay wet, plates arent clean. We have changed detergents pods as well. We may junk it and buy something else. Recently purchased clothes washer and did not buy Whirlpool. Very, very disappointed. I should have kept my 12 yr. old GE Dishwasher that wasted water... But cleaned my dishes. Not happy with Whirlpool!

We purchased the Whirlpool Duet Sport matching washer and dryer new in 2006 from a local appliance store. The washer was around $1,000. The salesman sold us on the load capacity, telling us it can wash 15 pairs of jeans. We dont overload it, mostly because its a high-efficiency washer and doesnt use much water (Im still trying to figure out the concept of how can you clean a whole load of laundry with a little bit of water). Its very quiet, but the cycles take longer than standard washers.Also, you must use very little soap (too much soap will cause the washer to stop and display an error code, which youll have to call a technician to come and reset). It is now 2013, and the washer started thumping during a cycle and there was a burning rubber smell. We called an appliance repairman who gave us an estimate for repair of $800 to $900 (for a bad bearing/bearing casing and inner basket). Im sure that there was quite a markup on those parts! It seems to me that the older non-efficient washers lasted longer than 7 years, and certainly didnt cost $1,000 when new.

Everything I buy from this company breaks all the time. I purchased these brands hoping they were good but apparently not. Always have to get them serviced. Lately they did an exchange on my fridge. Hope it helps because after thousands of dollars of food in the garbage it better work. And the washer thought, Oh Im paying more. It will be good. At this point will cost me less to buy from another company. Buyers beware. Cause the company cant do nothing good for me so dont buy from them.

Worst refrigerator (French Door Refrigerator WRF989SDAB00) ever! Even though this Technical Service Pointer was issued, it takes forever to get any satisfaction from Whirlpool. They were not pleasant to deal with when calling the Whirlpool Corporation. I had to research the problem while on the phone with their service representatives. The technician arrives and confirms that the evaporator in the fresh food section is indeed the problem but then it takes days for the parts to come in and then another appointment will be scheduled. Whirlpool does not provide good customer service. A refrigerator should last more than three years. Very disappointed and would never recommend Whirlpool to anyone.

Installed in May 2007, paid $674 for GU2455XTSS1 Whirlpool Dishwasher. It required service in March 2009 for $158 It became noisy in Oct 2011, so I placed a service call for $136. It was very noisy in Jan 2012. Again, I placed service call for an additional $93 that Whirlpool has not reimbursed. I must now replace the motor quoted at $403. The motor has a 90-day warranty. The 4.5 year old dishwasher must now be replaced. Whirlpool has not responded to email and to registered letter requesting a cost-effective solution to repair dishwasher that recognizes that reasonable life of the unit should be 10+ years and not 4.5 years.

It took 5 deliveries to get a fridge that wasnt damaged. First two came from Leons - the same damage on both. Then they said we had to go through Whirlpool because so much time had lapsed. We had purchased the full set of Whirlpool Gold for our kitchen renovation; therefore, we were unable to unpack the fridge until the cabinets were completed. I phoned Whirlpool Canada, and they said they had to send a service tech. The service tech came, and he confirmed the damage and was told to patch it with a proxy. Sorry but I had just paid $1500 for a new fridge. I didnt want a dent and damage. We received no offer for discount to accept the damaged fridge. They sent another one, still damaged. They used their truck to deliver and the guy had no idea how smashed our brand-new trim.So Whirlpool sent another fridge, and even though I asked them to check it before sending, they didnt. It was damaged. This is four fridges. Im tired of fighting with Whirlpool. I called Leons, and they take care to get me a new fridge undamaged. I told Whirlpool about the damage, and they sent a form. First, they wanted me to claim on my house insurance. Why should I put on a claim? If not, get two quotes and fill out tons of paperwork. Im just too tired after fighting for over two months to get a fridge that isnt damaged. Not even an offer of compensation to cover all the time taken off work and the stress on me and my family. This is the second set of Whirlpool Gold we have purchased in the last 4 years. I doubt I will ever purchase again, because you are a company that doesnt treat your customers with respect or concern.

The ice builds up over two week periods and begins to leak onto the floor, requiring me to empty the freezer, chop out the ice and put everything back. The repair job is in the vicinity of $100. Check the net. This problem is endemic. Since this is a problem created during the manufacturing process, Whirlpool should be fixing this problem free of charge. I will never purchase another Whirlpool product.

This washing machine is awful. It takes twice as long to wash clothes. My older washing machine did clothes in 30 minutes or less. This thing takes over and over stop go, stop go, stop go. Open lid it fills again and removes water, when spinning the lid locks and you cannot open it without unplugging and starting all over again. The wash doesnt even circulate to clean the clothes properly arggghhh. Annoying as all get up. The washer has no control for the water level. The clothes dont have enough water to clean or rinse. I spent over $500 on this and cant get rid of it as most people are selling these on local websites as they hate them as well. Whirlpool thank you for taking my money and producing this junk. Never ever again! I think the seller is also responsible for not telling me what to expect of this junk.

Last December our refrigerator began to freeze food - gallons of milk, bowls of food, and produce. I called Whirlpool: Of course the warranty had expired. It was suggested we turn the unit off back on to reset the computer. We did this for 2 or 3 months and eventually it worked properly. We were gone for 12 days, now the icemaker has stopped and all food is frozen. I called - they will send a tech for a minimum of $95. Read how many trips are usually made before a problem is solved. Cheaper and more logical to buy another unit from anyone but Whirlpool.

I received this Email from the Whirlpool Director of Consumer Care to evaluate my experience with their customer service department. I filled out the survey over a week ago including a complete documentation of my problems and have not even received an acknowledgment of the survey or promise to look into my problems.In the last 7 months I have experienced problems with 2 Whirlpool major appliances which both appear to be unrepairable and which have been unsuccessfully brought to the attention of your customer support group. In March a fridge and in October a clothes washer. Both were high end products roughly 3 to 4 years old. I did not have an extended warranty with the fridge so I dealt directly with the customer support group. However I was covered by warranty with the washer and your distributor Bad Boy have been making the calls on my behalf but have been just as disappointed to date as I was.Both cases were very similar. In both cases the repairman came out within a few days and promised to return the following week with the broken part but I have never heard from either one of them EVER. In the case of the fridge I was told to defrost it the day before the promised repair date and lost all the food $$$. At this stage a number of calls went out from me to Whirlpool for the fridge and from Bad Boy for the washer and eventually we both got a new delivery date of roughly one month. Both times the date passed with no shows and no call backs. Repeated calls later to the customer service group, with promises of EXPEDITING the delivery, the fridge part delivery date was extended to 3 months so we had no choice but to buy a new fridge. As for the washer, Bad Boy even had an unsuccessful face to face meeting with your representatives and we have had no word back or expected delivery dates well into the third month.I HAVE NO IDEA WHAT TO DO? I have made so many calls with so few call backs and no clue what to expect or when? Your representatives use the word expedite with no idea what the word means. At the suggestion of one of your representatives I even called one of your distributors Sears to see if they had the part. Their Canadian head office is in the Philippines and they said they had the same problem with Whirlpool. Twice I tried to talk with your representatives supervisor and both times were unsuccessful.In a world of computers where it should take seconds to find inventory parts and expediting packages usually refers to next day delivery, the fact Whirlpool requires months is unbelievable. The only explanations I can come up with is 1- You dont make parts for your appliances. 2- New appliances are made so poorly all parts are gone. 3- You could not care less about your customers. 4- You dont own a computer. Most of our appliances are Whirlpool because we thought you had a good reputation. We had to purchase a new fridge and still have had no word on the washer?

Bought a new $899 dishwasher 7/2020 and it stopped working 10/2020 And it’s been weeks and now I’ve been told it will be another 21 before they can replace it if at all! #whirlpoolusa #whirlpoolcorp Customer service lady was rude with an attitude.

Whirlpool N50T61-403 - I bought this thing today 8.21.14 from Lowes. It is a Whirlpool 50-Gal water heater (6th sense) and was going to have it installed by their installer, but elected after seeing it was very similar to lining up with my old unit. I got it in and then filled it. After filling, I lit the pilot light per the instructions then turned the knob for heating it up. Success, the flame spread across the burners...then went out. The steady blink changed to the 2 blink code indicating a bad thermopile. It did not work - right out of the box. No plumber near me carries the part. Whirlpool has thus been pretty good about it offering to have someone come out at their cost... But if no one has the parts, that is no good. I am moving from this house so if we can get it to work, its the problem for the next owner. If not - Ill have to get an RMA and go back to Lowes... Then try the Rheem from Home Depot. Will see if they will overnight a part tomorrow. I found the other reviews - and I dont like it that this thing appears to have difficulty right out of the box.

KitchenAid double oven glass exploded during the self-clean cycle. The oven was purchased on 9-20-11 and the glass exploded on 11-30-11 during the first-use of the self-cleaning cycle. The cavity was damaged with dents and shards of glass from the explosion. Unfortunately, the warranty for KitchenAid is replacement of parts and repair only. Nicole, supervisor at Whirlpool, offered to extend the warranty 6 months. Then I was somehow disconnected from the call.

Please do yourself a favor and stay away from both Whirlpool and this unit. I purchased it from a local dealership and paid $881.00 which included tax and delivery cost. In less than 2 years, it broke. Whirlpool does not offer a warranty on the unit. After having a Whirlpool repair person come out for a cost of $75.00, I was informed that the parts to replace would cost $800.00 not counting additional labor cost which was TBD. I contacted Whirlpool and went from Agent (Phylicia) to supervisor (Ashley) to Manager (Carol **). The best offer I was given was to buy the parts at a discount of $400.00 which did not include tax, delivery or labor. So it would have run approx. $550.00 to over $600.00 to fix a $771.00 washer.My next letter is to Jeff Fettig (553 Benson Rd, Benton Harbor, MI 49022/ CIO of Whirlpool) to let him know how impressed I am with his product and customer service support. The next Whirlpool item I buy will be never. Take this as a word of warning to go Maytag or any other vendor because Whirlpool will not support you once the sale has been completed. Good Luck.

When purchasing a new home, the almost new Whirlpool double-door ice-dispensing stainless steel refrigerator came with the kitchen. This beautiful-looking fridge worked well for close to three years, but gave up the ghost shortly after its warranty expired; designed obsolescence perhaps? Problem was, it would have cost almost as much to repair as it would have to purchase a new fridge with a warranty. So, thats what I did, via a local big-box store. I bought a single door floor model, with the Whirlpool ending up as scrap, the whole incident leaving a bad taste in my mouth. If you have your grandmothers old fridge that still runs, keep it!

Sent an e-mail to Whirlpool. They responded with apology. Sent a second e-mail telling them they should be paying the $300 for circuit board in a two-year-old range. No response. Also, sent e-mail to Geniers. No response. The impression I get is that neither are the least bit interested in the problem. Once they sold the $1260 range, they were done. We will never buy another Whirlpool from any store and we wont buy anything from Geniers in the future.

I purchased a Whirlpool side by side refrigerator and it was delivered on 1/22/22. We had it five weeks working fine then on 2/27/22 it stopped working. Whirlpool service came out and said it was the compressor but all parts are on backorder and no telling when they will be in. Maybe Lowes would replace it, but no because it is longer than 30 days. Lowes when I bought the fridge had over 400 of the same refrigerator in stock so why is it they couldnt had replaced it. Or if Whirlpool sells items on their own why didnt they just replace it. We have been going on 3 weeks without a fridge. With all of this said it didnt even last the 7 years they say they last for now. That is ridiculous when the last one lasted 20 years. In 7 years I will be on a fixed income how am I suppose to keep living. Something is wrong here.

I like my dishwasher very much. Because we have hard well water I use Lemi Shine to cut down on any deposits. The top shelf is adjustable so that helps with large pans getting clean.

If you are on this website, keep reading. You will definitely find many people that have your same problem. We purchased our refrigerator 5 years ago. Since then we have had a leak inside of it which is gradually forming mold that I have to cleanup. The ice maker and water dispenser do not function for months at a time. I just purchased 2 drawers for the same reason as the review on May 5, 2016. The tabs break off of the front panels and the panel falls off of the drawers. Theres no way to pull them out. We paid over $200.00 for two drawers!I spoke with customer service at Whirlpool and read them the 2016 review. Their answer was that you should not believe everything you read. My answer was, How cant I? Its happening to the refrigerator I own. They just kept giving robotic answers. The conversation was that of someone that is in denial of having a problem. They dont care. Instead of at least offering a discount on the drawers, she offered me an over $400.00 one year warranty. Pathetic! Whirlpool has just lost another customer.

We too have nothing but problems with our supposedly top of the line convection/microwave oven. Purchased in 2010 in February for new kitchen. From start, original microwave installed did not work, would not cook or heat. Dealer replaced. One year later, same problem, but now out of warranty. Had to pay labor, costs, and parts to get fixed. Fast forward 13 months, again magnetron needs replaced, microwave will not work. What a hunk of junk for our money. I will never buy any Whirlpool appliances again, and I will tell everyone I know the same. When you call customer service, they are nice but only say “too bad, out of warranty”. What a joke for a major appliance company to tell customers. It is obvious that this microwave is faulty from the get go, and they just keep on making them the same way and not trying to fix the problem.

I purchased a rental home with a Whirlpool hot water heater. In the home inspection, it was deemed to be in good working order. The first day the tenant moved in, I received 3 service calls for no hot water. My contractor told me I needed to replace the start up assembly and it needed to be ordered from Whirlpool directly, as it is not available in stores. When I contacted Whirlpool Customer Service, the operator, Stacey, was rude and unhelpful. She told me that the warranty was void because I was not the original owner, even though it does not state that the warranty is not transferable. She also told me she could not help me order a replacement part without the item number.

We got a french door Whirlpool refrigerator about 15 months ago. Model Wrf757sdem01. There were problems from day one. Serviced about 6 times by 3 different companies... Died again less than 2 weeks ago. Finally the store decided to replace it. Was under an extended warranty. We have been without a fridge for over 10 days. It has caused multiple problems for us as we are out in the country. We have to haul ice to 4 coolers... Wait on the new one (a Whirlpool). Plumber had to be called in and he has had 3 of this same model replaced! Years ago you could trust Whirlpool. Now apparently not. I hope we do not have to regret our replacement one which still is not installed! By the way the water filters have to be replaced to the tune of 100.00 a year. We are not going to use an icemaker or get water from the new one.

In 2010 we had to purchase a new hot water heater. Went to our local Lowes store to see what they offered. We decided to buy a Whirlpool energy smart electric water heater. It was large, 50 gallon. We have a large family and didnt like running out of hot water so we thought this would be great. Worked fine until yesterday when I kept smelling an odor like something melting. Could not figure out where the smell was coming from until this morning I got in the shower and had very little hot water. Went downstairs and seen the water heater was not working. Got the user guide out to see if we could pinpoint what was wrong. It said no power to control board. I checked the breaker box and found no problems. I got a flashlight to look at the control board and discovered it had overheated and melt the top of it. Have been on phone with Whirlpool nonstop with just a recording. The heater has a lifetime warranty so Im trying to get the replacement part for it that will cost me $115 plus shipping. I am really concerned that with this overheating it did not trip the breaker. Grateful it did not start a fire and worried if we repair it will this happen again and possibly not be as fortunate. I have seen on this site of another complaint with the same problem. Shocked there hasnt been a recall issued. Be careful!

Four year old Whirlpool Refrigerator/Freezer Model W10771736A. Ice maker broke right after the warranty ended. No refrigerator or certified whirlpool repairman was able to fix the problem. Our microwave is cracked on the side, and it is only four years old.

We bought a Whirlpool front door open washer machine from Best Buy on Oct. 2, 2011. We didnt start to use until our basement got finished. In November when the basement was ready, we found out that the machine didnt work at all. We called A&E factory service as suggested by Best Buy. They sent technicians 3 times in 2 months to check the machine. Now, it is 3 months later since we purchased the machine, the machine is still not working. We contacted Whirlpool, and they would not exchange to another machine, instead, they told us they will send another technician to check it once again. This machine costs us $800 before tax, but until now, it is still not working. Can you tell us what to do? We called Best Buy and they said this machine is under factorys warranty. So we called A& E service, who said that if Whirlpool called them, they will tell them it cannot be fixed. However, they need Whirlpool to call them because they work for Whirlpool. Is 3 month waiting not enough for a brand new machine to get fixed? And the worst thing is we still owe money to Best Buy creditor. Please help us to get rid of this! Thanks!

We bought this fridge 1 year ago. We have already been without a fridge from Oct 2016 to Jan 30, 2017 due to a drawer going bad which caused the whole thing to quit. Now it has an obstruction in the Freon lines that causes it to freeze up and not cool. It was deemed not repairable by service company sent by Whirlpool/KitchenAid, and yet they want one more test run. The last person I spoke with at customer service had a flippant attitude and said there are no notes. What they do is drag you along for so long, make you wait and abuse you with tests, and hope you finally give up and go away. I will never buy another thing with Whirlpool/KitchenAid stamped on it!

On March 3, I purchased a dishwasher (Model: KUDE70FXSS1 Serial No.: F10202361) on Whirlpools VIP link, which will more likely be my last Whirlpool purchase based on the slightly damaged product and incredibly poor customer service Ive received. Upon delivery of the dishwasher on March 9, I noticed that the left rear wheel was damaged and slightly bent. I also noticed that the unit was a little off balance. But the delivery person explained to me that everything was okay and that the front legs just needed to be adjusted. I believed him and signed the delivery receipts with the additional note about the left rear wheel being damaged. At the time of delivery, the driver also happened to mention that J.B. Hunt did offer installation services for dishwashers. I then called Whirlpool customer service, which pretty much gave me the cold shoulder, and said that it wasnt in their policy. I had to request the installation service at the time of purchase and Whirlpool would not send someone back out. This made me upset because I initially wanted to have the dishwasher installed but your VIP link didnt show an option for installation. Im not sure how Im supposed to request the installation services when theyre not being offered. But the genius customer service representative thought that I should intuitively call Whirlpool when the link isnt on the website. This is the first demonstration of Whirlpools poor customer service, in my opinion. After a couple of days of driving around to get a hose and a cord to perform the installation, I finally installed the dishwasher on March 12. Once installed, I noticed that the hinge on the left side was rubbing against the tub of the dishwasher. The door hinge was bent and the main tub was slightly damaged. Again, I contacted Whirlpools customer service department who sent out a repairman who confirmed that the dishwasher needed new tub and hinges which were covered under warranty. Unfortunately, he told me that I would not receive a new dishwasher since I installed it myself. He would order a new tub and hinges and transfer all the equipment and wiring from my original dishwasher to the new tub. Essentially, I would have a refurbished dishwasher at a new price, which I do not want.I initially wanted to have the dishwasher installed but your VIP link didnt show an option for installation. If Whirlpools website worked the way it should have and offered an installation service, I wouldnt be in this situation. I would have paid for the installation and the people installing the new dishwasher would have realized that it was damaged prior to them leaving and ordering a new dishwasher. I am a customer and not a dishwasher repairman. No normal person would have been able to catch the damage that is on my machine. Second, I find it hard to believe that Whirlpools policy states to have all the equipment from my original dishwasher installed on a new tub. So, I paid $989 for a new dishwasher thats really a refurbished dishwasher because of the damage. I wish I would have visited this site prior to purchasing. I will never deal with Whirlpool again.

This dishwasher does not clean the dishes. Having said that most of the dishes are too oversized for the small capacity. Perhaps the fact that this is such an old dishwasher. I’m not sure but none of the dishes get washed. About the only thing that works is the dryer heater. Sorry to say, I’m not happy with this dishwasher and wouldn’t recommend it to anyone.

We bought our Whirlpool Cabrio 7 years ago and it was great at first. I have not had any trouble with it ripping clothing. The clothes are clean. Its constantly breaking down. First it was the drain pump. Then the main computer board went! I called Whirlpool and of course the lady says its not covered. I had back up though. Google is amazing! I asked why this wasnt a recall as all over the web, people had this same problem. I pushed and pushed and she put me on hold. Came back to say it was in fact covered. What? Really? What changed your mind? She wasnt allowed to tell me. Supposedly had something to do with the date of manufacture. So okay, they send the repair guy out, its fixed. Now tonight, the lid locks and nothing happens! This repair was about 6 months ago. Grrrrr. Its been one thing after another with this hunk of expensive junk. When I buy an appliance I expect it to be problem free for far longer than this. I am not getting a code or anything, just dead air. So frustrating with three kids not being able to do laundry when I need it randomly :( Has anyone else had this problem? The lid locks, then does nothing. I unplugged it, pressed off and restarted it. Changed settings. Nothing is working.

Yes, Whirlpool makes Maytag, Im still paying for this junk. Too much to go into detail. I had to bypass the crummy fuse system in the Bravo dryer and hook up my own 15amp automotive fuse in the dryer to keep it working. This after two lame under-contract Maytag repairmen replaced the dreaded board, which did nothing. The washer goes cabunk, cabunk, cabunk throughout the house and shuts down with an unlevel code (no matter how level the load is) every time it does its load during the spin cycle. The dishwasher handle broke off and had to use a screwdriver to pry the handle latch open, until realized it doesnt even lock anyway and just pulled the door open. Now, the dishwasher has this noise problem which means they designed it to allow pieces of debris to escape past the trap like my other dishwasher had that was easy to remove and clean. Do not, I repeat, do not pay the $3,500+ I paid for this junk. Go buy a Kenmore thats 15 years old off of Craigslist! Youll be better off and it will last longer.

I bought Whirlpool water heater model #FG1H5040T3NOV about 5 years ago. Burner assembly was replaced two years ago and now, thermocouple was replaced yesterday.

This washer (Cabrio 6th Sense Washer) is less than 4 years old and now needs $500.00 worth of repair. You have to replace the tub in order to replace the bearings. If your washer starts to make noises during the spin cycle, you are in for a big repair bill. I still havent decided if I am going to repair it or junk it. The towels always smell sour even if you wash them twice.

This was the first new appliance that I had actually ever had and I purchased it in October of 2010. After four months, it started make a grinding sound. I called Whirlpool and the repair man replaced the motor. Approximately four months after that, the lid got stuck and the machine would not respond. Same routine as before, but this time the transmission was replaced. While the machine was apart, I noticed the white insulating panel from the bottom was brown in a spot and looked as if it had gotten hot. A month before the 1 year warranty expired, the washer started making an intermittent grinding sound nearly identical to the sound made when the motor went out. This time a different service company was sent out my Whirlpool and the said that nothing was wrong. Now, the machine is out of warranty and has stopped cleaning close and during the spin cycle the you can hear water running into the machine constantly. Last months water bill shows a 40% increase in water consumption when nothing has changed to incur a larger bill. Seeing all these comments makes me wonder why the heck nothing is being done to force recalls on such poor products. Consumers should be treated with a lot more respect than this. I will never recommend a Whirlpool product to anyone I meet. In fact, I will strongly discourage anyone who is contemplating buying a Whirlpool washer machine.

We purchased the washer on April 25, 2015. It has been an absolute nightmare. Reached out to Sears within a week of delivery because the wash cycle was way over an hour. Is a terrible machine, my clothes come out dirty, is damaging my clothes and Sears says I cannot return it because according to them I havent had it fixed enough times. It washes for over an hour at times. It takes water and releases water and goes to wash again but is not cleaning the clothes. As a homeowner we pay water, and electricity and perhaps I wouldnt be so upset if my clothes would come out clean. At first the tech told me to change from the HE detergent purchased and recommended at Sears to liquid detergent and then since I still get stains on our clothes he advised me to use less than the recommended amount. I also purchased the kit to wash the machine. This is a real lemon and nobody wants to admit it. I have purchased Whirpool washer before but if they dont admit that this is poorly made and give me a voucher to buy another machine I will never ever in my life buy Whirlpool or Sears for that matter. The machine is just a year old and I cannot use it because it damages my clothes and worst, is not cleaning my clothes. It disgust me to wear dirty clothes or to have my family wear them. So now I have another appointment and at this point I no longer use the machine. I will tell everyone that is willing to hear my experience. Do not purchase this washer, is not good and is only trouble. You are not going to be able to get it exchanged or fixed. I think that a full year would have been enough time for Sears to determine this is a lemon and do the right thing by the customer. I now go to the laundromat because I have a machine that damages my clothes. I am also out of money to purchase a new one and the wearing dirty clothes disgust me.

This is the worst washing machine I have ever owned. I have had the Whirlpool Cabrio for less than three years, (4 people I use it for), and it is so loud when it is in the spin cycle, you think a jet airplane is taking off inside your house! Apparently the bearings go out of these machines when you use them! I called the company and all they want to do is sell me an extended warranty for over $300.00 for another year! Not doing that! I paid over $1,000.00 for this machine. I thought it would last a long time! Wrong! Please save your money and get a simple old fashioned one! I sure wish I had! Whirlpool doesnt care about their customers, or they would stand behind their products!

We bought a Whirlpool French door fridge model WRF989SDAM00 in 2013 and were impressed by how it looked in our kitchen. Its December 2015 and things have started to go wrong. First the freezer stopped freezing items completely and found out that ice had built up on the cooling tubes inside the rear freezer wall. Had to be taken apart and thawed with a heat gun. Now the freezer freezes on and off and the ice maker is not making ice properly and leaking all over the left side of the fridge. Went to Sears {place of purchase} and we were asked immediately if we had purchased the extended warranty. We hadnt and were told Sears could do nothing and that these newer fridges have a tendency to have trouble within the first couple of years and thats why they recommend the extended warranties. Really a $2500 dollar fridge a couple of years? Had a local appliance repairman look at it and he said the compressor was bad. $500.00 to fix. Boy do I regret buying this thing. These big companies just walk all over us consumers.

This dishwasher, compared to my old one, is very quiet but does a very poor job of cleaning. I now have to prerinse most all items. The silverware rack leaves many dirty items such as peanut butter off a knife. I probably waste more water on prerinse than what is saved by the washer.

We purchased a Whirlpool Duet Front Loading Washer and Dryer. The control panel on the washer went out in March. We called for a repair. The repairman came, told us we needed to replace the control panel and he would order it. My American Express was charged $389.91 on March 26th. I called today, April 9, asking about where the part was and when my machine would be repaired. I was told the part would not be available until July 11, 2013. I cannot believe that a company would expect a customer to wait nearly four months for a part as well as charge them for the parts and labor four months ahead of the part. When I called, I was first told that there were 15 parts in stock, but then was told that there were not any available to me. I have cancelled the service but it will take them three weeks to credit my card back for the part.

Whirlpool Duet - Front loading with additional base makes loading and unloading easy. We have had the washer and Dryer about one year now. They were replacements for Kenmore front loaders. We replaced a Kenmore front loading pair that served us faithfully for more than ten years. But when we purchased a new house we decided that it was necessary to upgrade to better units. The Whirlpool Duet pair has performed exceptionally well with one little caveat. Periodically we have to unplug the units to reset the computers when they dont function properly. Small problem, easily solved.

I purchased a new home 1 year ago, our home came with Whirlpool Appliances. I was so excited because we were renter. The refrigerators after a year all of the LED lights have gone out, and the refrigerator make a very loud noise. I have called customers service several times. Their respond is, Sorry. It only has a 1 year warranty. The cost of the light would be over $500.00 dollar and that dont included labor. Dont even know the cost of fixing the loud noise. I just want people to be aware of Whirlpool appliances. After only 1 year of service it not going to work. Whirlpool will not fixed them. It sad we work hard to get a home and how will have to spend a fortune to get them fixed. Whirlpool you need to make better equipment. With is coming without home we were not giving an opportunity to buy an extended warranty.

I purchased a new Whirlpool washer, from day one it did not work, for the past month I have been trying to fix the problem with service people. The service people were at my house 5 times without any positive results. I was told by Whirlpool representative that they will not replace the washer or give me my money back, they have 12 months to fix the problem. I have never seen such a bad customer service and arrogance towards a customer. I will never buy anything manufactured by this company.

My hot water tank wont stay lit. I replaced the heating element, and the thermo couple. It will light up now but it only stays on for about 10 minutes.

We were a Whirlpool family, and have been using a Whirlpool front loader – Duet Steam Model # WFW9500TW - for the past nine years without any issues until recently when it started to vibrate. Technician sent by Whirlpool blamed it on failing bearing and that it was cheaper to replace than to repair (In hindsight, I wish we had tried repairing). Naturally, we decided to replace with a new front loader from Whirlpool - Model # WFW6620HW. Our previous version had a max spin speed of 1000 RPM and a capacity of 3.5 cu. ft. This new one has a top spin speed of 1160 RPM and a capacity of 4.5 cu. ft. The main problem with our old one was vibration, and this was being caused by the washer going into high spin while the clothes were not evenly distributed throughout the drum. In one spin, the clothes would spin perfectly without any vibration, but in another spin of the same cycle, the washer would not allocate that same clothes properly throughout the drum, which leads the drum to cause vibration from unbalanced high spin. Vibration is a problem, because like most Americans, we live in a wood frame house, and have a basement underneath with the washer located on the main floor. Vibration from unbalanced high RPM spin gets sent down to other areas of the house, causing damage, drywall cracks, separation in trims, etc. And these are all only the damages one can see with their eyes.One point about vibration and some myth busting. Provided that all your washer legs are meeting the floor and not on a saggy floor, your washer should not vibrate more than it does during an empty spin. If it does, then it is due to faulty, poor design/engineering. What happens is when the steel drum becomes unbalanced with laundry in high spin, it starts to shake as more of the weight is on one side, which one can notice looking inside the washer window. There are concrete weights fastened to the top and bottom of drum to keep the drum in place and to reduce its shaking tendencies. However, this weight also causes the washer cabinet to wobble if the drum itself is shaking. This wobble in turn causes the washer legs, which may be firmly grasping the floor, to very slightly come off the floor, which one can feel if touching both the washer feet and floor with their finger at the high spin of an unbalanced spin. And that motion of legs coming off the floor and hitting back at high RPM is what causes vibration to be felt on the floor and to be seen on the cabinet. Of course, this effect is amplified with washers that decide to go into an unbalanced spin with an even higher max spin. When our old washer perfectly balanced the clothes, it behaved like it was running high spin while the drum was empty. This is how all washers should behave, especially in America where the vast majority of homes are wood frame based. However, that was not what we experienced with this new Whirlpool. If a washer is not capable of balancing out the clothes, extra function or feature should be deployed in containing the drum shake to within the drum, and not allow it to escape.First, our old front load Duet Steam Whirlpool was Made in Germany. This new one is ‘assembled’ in America. The door window of the new one is plastic and feels cheap and flimsy, but I expect all the darker color door windows of newer front loaders to be plastic. Consider it cost cutting. We did not look for additional anti-vibration technology because our old Duet didn’t have anti-vibration features aside from its two springs and four suspensions. We decided not to use Load & Go because I have personally seen liquid HE detergents gum up over time, so I didn’t want to risk it gumming up inside the washer.After the installers left, I spend an hour cleaning the outside of the washer to perfection. Sadly, time wasted. Once I was done, I first did a wash without clothes, and then with clothes in Normal, fast spin cycle with drum about 2/3rds full. Just pants and t-shirts. There is a recirculating pump at the top of the drum to distribute the water, and to also distribute soap mixed water. But I am not sure if this is without problems. These pumps can collect soap residue with time, and you will eventually end up rinsing the laundry with soap mixed water even in rinse cycle.In getting to the first spin in wash cycle, I was flabbergasted to see how, just how rudimentary, I want to reiterate the word rudimentary, the load detection was before entering high spin. Our nine-year-old washer had a more comprehensive one. The new washer would spin the clothes at very, very low spin and simply see if the drum is most evenly spinning. That’s all. Compared it to our old washer which would also shake the drum to see if there was movement from side to side, because clothes can change their position when entering high spin. This rudimentary load detection causes the new washer to create an even worse uneven load distribution around the drum before spin, even though it may seem even at very low RPM. So, why is the new washer’s load detection so basic? I believe it is due to ball bearings.Front load washer models from other companies employ ball bearings to reduce vibrations from uneven loads. Whirlpool does not employ such feature, at least, they do not advertise them. However, to my surprise, I hear metal balls hitting each other every time the drum direction changes during the wash cycle. I inquired Whirlpool about this and I received contradictory responses. My theory is that the basic load detection before spin speed is used because Whirlpool assumes any changes to load distribution will be taken care of or reduced by the ball bearings of the washer. But this ultimately allows the washer to go into more uneven spins. The bearings may also be used to increase the tolerance of what is considered an ‘unbalanced load’ in order to get the washer to go into spin cycle faster, decreasing the time involved of the washer to go into spin cycle. Sadly, to my dismay, the new washer ended up causing a worse vibration than our old one with failing bearing.I called up the retailer the same day of delivery and complained of vibration. He first sent an installer to see if it was installed properly, and upon showing the installer of the vibration issues, the retailer sent me a new washer couple of days later thinking the first one was a lemon, and even though it has less noisy draining noise, it too exhibited the same issues with it going into significantly uneven spin. In the end, we decided to return the Whirlpool washer all together, at a loss of $200 because the retailer did not hold up to their spoken return policy.We have done many loads in this washer to see if our loading is an issue, loads of varying sizes, loads of varying types, loads of weights, and we maybe only had an evenly distributed load around the drum about once or twice. Once it was a King comforter. But, like our old washer, this too ended up not distributing properly around the drum in the final spin cycle and started vibrating, even though it was vibration-free in the previous high spin cycle. This proves that the problem exists directly within the washer, not the floor, leveling, load, etc.Some other problems with the washer: - The washer door, Load & Go dispenser at bottom, and single load dispenser at top are all plastic parts which all vibrate significantly during fast spin cycle. Especially the Load & Go dispenser which keeps hitting the cabinet to make banging noise. - Drain sounds are much, much louder than our previous Duet. It was even louder in the first one we received. Combine this to uneven spins and this washer can perhaps compete with an engine in terms of the sound it generates. - Single use dispenser at top left will hit the washer door if washer door is opened when the dispenser is also in open position. - Buttons are sometimes unresponsive, to which I have to power off and try again. But this has only happened a couple of times.- There is a small ¼ in. opening where the steel drum meets the rubber gasket, opening in which items like coins, etc., may fall through and are irretrievable. Don’t think small socks would be affected.To potential buyers, I suggest you proceed with caution when it comes to this washer. Understand the retailer’s appliance return policy and make sure it is shown in paper. It can save you a lot of headache. Get the extended warranty of three years because manufacturers only give you one-year warranty for a reason. I would also suggest that you avoid this washer at all costs if you have any floor level below where this washer is to be installed, especially if the level below is a basement. Your house is more important and more valuable than a $1000 washer.In the end, I am very disappointed in Whirlpool, an American company. Perhaps Whirlpool focuses their attention on top loaders, not front loaders. But Whirlpool had nine years to improve their washers, and it is sad that we may now have to go outside of America for a quality product to be used in American homes. P.S. No solicitation please, Whirlpool. This washer is in the process of being returned. P.S.S. I already posted this review in Whirlpools website, and it is under moderation.

My $1800 French door refrigerator is only 20 months old and the ice maker has quit working. They sent out a repair person 5 times and replaced parts three of those times. Now they are saying it is unrepairable and are refunding my contract fee of $345 and leaving me with a broken ice maker. When the problem started it was making ice just not dumping it. Now it doesnt even get water. Throughout this all, two months, I have had to constantly call them to find out our next move. They say someone will call me in 2-3 days but they never do. One of The last people I talked to said, Well you can still keep food in it. I dont feel that is reasonable considering I bought a refrigerator with the ice maker in it. I finally called Whirlpool corporate instead of the service contract people to see if anything could be done and was told someone would call me back in 2-3 business days. Well its been a week and big surprise - have not heard from anyone. It is looking like we will have to purchase yet another refrigerator in less than two years. The service people I talked to were rude and really didnt seem to want to help at all. I believed when I purchased this Whirlpool product that they were a reputable company. Sorry to say that is not the case at all. I dont know if the refrigerator is really unrepairable or if they just gave up trying to find the issue. Seems hard to believe a basically new appliance cant be repaired.

I purchased this stove in September and I am very unhappy with the Aqualift. The service department said I would have to probably do the cleaning process about 7-8 times for it to really work. I find that very unacceptable would never recommend this to anyone.

We purchased in July 2016 from Best Buy. Very nice product. Our former Whirlpool had lasted 20 years and was a work horse for our family. The new one began not freezing ice cream in November. Then, it would periodically freeze things very well and then not freeze items fully. We contacted Best Buy thinking we had a lemon. Worthless - no help. Told us to contact Whirlpool directly. The repair person came out today and told us that our refrigerator cannot be in our garage outdoors because the energy efficiency of the refrigerator causes it to shut off when the surrounding temp drops below 54F. Our former Whirlpool had been outdoors in our garage in that spot for 18 years, no problems. The new models now no longer operate if the air cools down around them. What!? There is no warning information, no sales information, no way to learn this until after you shell out 1000 dollars and lose your frozen food. It is in the manual in fine print, but we didnt read the manual cover to cover when we got the refrigerator, and we sure didnt read it BEFORE we bought it. And no one at the store, nor the installation people who represented Best Buy as paid installers told me I couldnt have this outside, even though I specifically told them I was buying it for our outside extra fridge and freezer to replace the old one, and the installers installed it outside. Technically our refrigerator is working as its supposed to apparently. However, I think it should prominently be noted on pre-sales materials that it must be operated indoors only (in climates always >54 degrees). Now I have a new refrigerator that I cant use as an extra in our garage. Apparently all the new fridges are energy efficient like this and shut off below 54. I cannot find any info on the internet about this, or any other complaints about a similar situation to mine. How does that make any sense? Freezing is 32 so any frozen goods will thaw, by default, always, if the machine is in cool environments. Phooey on this design spec. Dumb engineers.

Here is my TERRIBLE experience: After only eight months it started to fail intermittently. Within weeks, it failed completely. I pay someone to come out and look. We get a part from Whirlpool. Pay extra to express ship it. 2 days later, pay to have it installed. Still doesnt work. Express ship another part. 2 days later, pay again to have it installed. STILL doesnt work. Express ship ANOTHER part. 3 days later - it STILL DOESNT WORK!!!!! Then they closed - wait another day. Now they authorize a complete replacement. Wait till Monday to PAY to have this one uninstalled. Haul it upstairs, into my car, back to Lowes, so I can get a new one. Haul it home. Pay AGAIN to have it installed.I was without hot water for 10 days and paid about 4 time the cost of the heater in labor to get through this MESS. I talked with Customer Service to get some help with how terribly unfair this was. Warranty Only Covers parts - should have bought the extra warranty... Silly me - I thought Whirlpool was a reputable and reliable brand. Boy was I WRONG!!! DO NOT PAY EXTRA FOR THE NAME - NOT WORTH IT!!!!!! I also dont recommend paying extra for the Energy Efficient. Its added electronics that just give it more to go wrong. Plain and simple is the lesson for the day!!! And after the hours of frustration with their customer service - Ill NEVER buy another Whirlpool product as long as I live!!!

Refrigerator, less than one year old, quit working and destroyed several hundreds of dollars worth of food. Whirlpool warranty division was notified and a service technician was scheduled to arrive yesterday, a week after the warranty division was notified. Yesterday, no one arrived. Today the warranty division was again notified and we were advised the service technician was never scheduled and they do not know why this happened. Here we sit again for another four days awaiting a service technician.I am disgusted with the failures of Whirlpool and their warranty division. Again, in less than a year Ive paid nearly three thousand dollars for a refrigerator and it fails, destroying hundreds of dollars of food. This has been a complete struggle trying to maintain food in a household both children. I expected a long time manufacturer to provide better warranty, service, and not just tell me they are not sure why. I would hope that no one ever buys their products again, God knows I will not!

Our Whirlpool Duet Washer pair is 2.5 yrs old. The washer didnt work at first, but a repairman found the problem and fixed it right up. They have not broken. The dryer has been fine and we have had them stacked for most of the time without any issues. My problem sounds minor compared to those others listed here, but this thing is ruining all our white or light colored clothes. They go in white, and come out covered with splotchy, dirty looking spots literally all over them! They werent that kind of dirty when they went in. It’s the oddest thing, like it makes dirt. Reading some of these concerns makes me wonder if it has a mold problem inside somewhere, and that is what is ruining our clothes. Tax return is coming and it is going. End of story.

We had bought a whirlpool refrigerator (Model - DC 205 5S/2016) in late April 2016. Initially I noticed a whirring sound after 6-7 hours of switching it on. As nobody from whirlpool had come for installation or any follow up even after requesting, we let it go thinking that nothing could go wrong with a new fridge. Nevertheless, the disturbing sound continued, until I noticed exposed wires running crisscross atop the freezer box and below it, one even preventing the chiller tray to be pulled out easily. Also, we had to get a stabilizer to reduce the notice even though it was written in big bold letters that it was a Stabilizer free refrigerator.After 8 months of owning it, we went for a three-day trip leaving the refrigerator on and set at point 3 in the cooling knob of which 5 is the maximum. On returning back, I noticed a crack at the top right corner of the freezer door and saw that ice had built up covering that side of the freezer inside. Again, as I had to leave for office within 1 hour, I let it rest and went. In the evening we noticed that the crack had extended, so we defrosted the fridge. The next morning I found a small piece of the freezer door floating in the defrosted water, and the freezer door was unhinged and askew at the top, in fact a part of the freezer doors upper right hinge had broken due to maybe the pressure of ice buildup, which had caused the crack that we saw.Shocking it was at first to learn that a freezer door be made of such low standard material ignoring the other fact of wires jutting out of the freezer at top and bottom. As the warranty period was 12 months, I immediately called the customer care, who put me on hold for 8-10minutes and disconnected, this repeated 2 times after which I was frustrated enough and vowed not to use the freezer again.After almost a month a more responsible member of my family took it upon himself and raised a complaint which was answered and a service person came home with a dirty looking and completely scratched piece of replacement door for the freezer. He informed that plastic pieces never came in warranty and we had to pay for it. Upon asking for further clarification he called his manager, Hemanth who was too rude and informed Madam you have pulled the freezer door apart which has caused this. Also, he was asking me specifically are you lying as you said initially that you left for 3days and now you said 5 days? We had left on a Friday night and came back on Tuesday morning, which means 3 complete days out of station. I never knew the exact number of days mattered as a fridge was supposed to be switched on continuously for days.Also, finally Hemanth was informing like if it was some mechanical or electrical fault we could have done it free of cost. So, I reported the whirring noise and the wires jutting out of the freezer tray. He blabbered at first and then informed me that the sound might be due to voltage fluctuation if you are not using a stabilizer (we were using one even though the fridge was a stabilizer free operation one, phew) and the wires issue he completely ignored claiming it as normal.So we paid in full for the dirty and scratched replacement door and also had to be called as liars and blamed that we had literally pulled off the door. Also, he was the most unprofessional manager that I had ever spoken to as he closed the conversation with, If it was LG or Samsung, they would never even have come for service like this. Enough was enough... Never in my life would I have anything to do with whirlpool nor will suggest this brand to anybody.They use such low-quality products. The warranty promises are just scam + even the managers are so insulting and bad mannered to the extent that I never want to deal with them anymore. Also, they dont think twice before just blaming the customers for their low-quality products. In all my years so far I have never come across a brand that treat their customers like this.

My three month old Whirlpool electric range caught on fire last night. The wiring that connects to the electrical cord to the stove shorted and melted. Thank God we were up and smelled it and quickly pulled the stove out and unplugged it. Had the fire dept out this morning and they verified that it was the stove and not house wiring. Now, I am without a stove, out of my money and waiting on the mercy of Whirlpool to take care of this situation. I do not want this stove in my house so I wont accept repair. Not sure I want another Whirlpool either. If this had happened during our sleep time, the whole house could have burned down. So upset and inconvenienced.

Whirlpool accubake slide in gas range - After using the auto clean button on the range, the digital panel will not work and the oven door will not open.

Had the fridge 5 1/2 years. Freezer quit working was told by 2 different repairmen it would cost $800 to repair. Called Whirlpool, was on hold 45 minutes, literally, both times I called. They could not help me. Called the corporate complaint line. The man I talked to was such a smart **! I finally said I cannot believe you are talking to me like this, I have bought Whirlpool for 35 years. He backed off slightly. Still couldnt help me. BTW, I LOVE my new Samsung refrigerator! Will NEVER buy Whirlpool again.

When we moved into our home this past year there was a Whirlpool gas stove model number W10406473A. We have the plastic knobs on the front of the stove which need to be pushed and turned in order to turn on the gas. I recently ran into a serious problem where my cat walked across the knob area and pushed and turned the knob causing the gas to come on the stove. This is a problem due to the fact that a child could have also have easily turned on this stove. This is a definite fire hazard as well as a carbon dioxide problem. I warn anyone with this stove to replace it with another make or model immediately. Im in the beginning mode of looking to see if a recall has ever been made on this model.

I just purchased a brand new home. I have an electric wall oven with the microwave over the oven. They are both built into the wall. Can anyone tell me why a massive amount of steam is coming out. It is really bad it makes my microwave glass so bad I can see through it. It is also making my cabinets so wet I have to use a towel to dry them. Plus I got a steam burn. Can someone tell me if this is normal.

After having the ice maker replaced on our 14-month old Whirlpool refrigerator, things seemed to be working fine for a while. However, now there are puddles appearing on the floor in front of the refrigerator. This is a freezer-on-the-bottom model and the ice maker is at the top so I was fairly certain it has nothing to do with the ice maker. Turns out there is something dripping into the back of the freezer and over time it builds up a giant ice sheet on the bottom of the freezer compartment. When the ice sheet gets large enough, the dripping water flows out onto the floor. Now Im going in every couple of weeks and chipping the big ice sheet off the bottom so it will stop leaking for several weeks. When I see puddles in front of our refrigerator I know its time to go chip the ice sheet out again. Seriously, I dont think Ive ever had a brand new, and expensive, appliance perform so badly. Whirlpool... never again.

I bought a Whirlpool Cabrio washer about 1 1/2 years ago. It has been in the shop 2 times and is doing the same thing again of not completing a wash cycle and draining. I WILL NEVER BUY Whirlpool appliance again. If I could sue I would.

I have used Kenmore products for about 50 years, so when it came time to replace my old washer I looked at Kenmore/Whirlpool. I upgraded to the top of the line. I had been warned by 2 service techs (2 different companies) that had tried to keep my old Kenmore alive that the new ones are not up to par compared to the old ones. The first very small load that I tried, was not even thoroughly wet when I took it out to put in the dryer. 1st service call, tech suggested that I put machine on extra water.That helped sort of. A few weeks later, wash is not getting clean. Called Whirlpool, they suggested getting the washer cleaner and clean the washer. Went out and bought a special cleaner, $10-12 and two cleanings later using the extra water and extra wash water I now was getting cleaner clothes. They said I would need to clean the washer every 2 to 4 weeks. I have continued to use washer but frequently have to rewash about 1 in every 5 to 10 loads as it doesnt always clean everything in the load. Called the Co., they sent service out, they said its OK!In Jan. We went out of town for 2 weeks. The washer had not been used for 4 days before we left. Came home to water all over the floor which are hardwood. Needless to say our hardwood is all warped! Service came out, ran the washer for about 15 min. and said it was fine, nothing wrong! Called Whirlpool again! Washer is now out of warranty. They said call a local service, out of their hands as it is out of warranty! Nothing more than they can do.I have used Kenmore/Whirlpool Appliances all my life and they have been wonderful. The new ones are garbage as far as I can tell. I have a Refer that is now 3-4 years old and I have had problems with that, a new dishwasher that is 2ish and have had service out on that one, now my brand new washer top of the line and it is so bad I am afraid to use it unless I am sitting right in front of it watching it! Further if you have the rinse cycle on the clothes come out so wrinkled that you need to get out your iron out and iron everything including sheets and linens. Lucky that I did not replace my old dryer! Do I recommend Whirlpool anymore? Not on your life. I wish I knew what to replace them with!

I purchased the Cabrio washer and dryer and paid for the extended warranty from Lowes about 5 years ago. After about a year, the washer had problems with excessive vibration and noise. Under Lowes warranty, a repairman came and adjusted the level. He came out several more times and made other adjustments, replaced the drum, then bearings and raised the level again. He said he could not declare the washer a lemon, even though it was because they were told this was taboo. They were instructed to do whatever they could to keep the washer going throughout the life of the warranty. Now the washer stops mid-cycle and an fl or f1 error code appears on the control board. I contacted Customer Service who said I can purchase another extended warranty for over $300 or pay their repairman for the visit including parts and labor. What I paid for the extended warranty and to purchase a new one would pay for a new washer.

The dryer is okay but the washer is no good. Doesnt save water because clothes have to be washed twice. Sometimes thrice to get them clean. Cycles are longer therefore more energy used. More water, more time, more energy. Terrible design. Useless piece of junk.

Love the chrome exterior and overall appearance of this side-by-side. The compartments and shelf spacing are well thought out & offer flexible adjustments. The outside components on the freezer (crushed ice, ice water, ice cubes, & light) I love, and most importantly the unit comes with a built-in replacement water filter.

First one had major problems. The bladder they call it. They took out the whole system out, replaced the tube that goes to the top of the refrigerator which is where it always starts leaking so they worked on it three times, junked it, gave me a new one and here I am again same thing. Ruined my hardwood floor and Im stuck with it. Never again will I buy WHIRLPOOL.

Weve been in this house for almost 4 years so the dishwasher (Whirlpool WDT790SAYM) is no older than that, maybe even 2.5 since I think I got it home in my CX-5 which is 2.5 years old. Anyway, never really had a problem with it and we run ours maybe once a day or twice in a row every 3 days. Last night I remember running a load and this morning noticed the dishes were dirty but the inside of the tub looked clean. So I plop another pod in and tried to run it again and sat there and watched it. It filled up with water but then nothing. After 20 minutes I opened the door and steam came out so the heater element was working and there was water at the bottom. I tried various things but nothing. Canceling still works.So either I try to get this fixed, or buy a new one. This wasnt a cheap dishwasher either. My wife balked when I 1st bought it considering she thinks a $300 model is better than most of these $500+ models. Right now I cant argue with her since we just replaced an expensive Samsung washing machine that lasted maybe 5 years. Theres another review of this model on these forums and the person tried to get it repaired many times and it appears maybe the same thing is happening to us. I wont go down that road considering repairs like that exceed the cost of a new dishwasher.

We purchased a new stainless steel Whirlpool refrigerator in February 2015. Within the first few days the fridge door handle broke off. Not that we have super human strength in our 60s but the handle connection is a very thin plastic. We put it down to the possibility that the warehouse or shippers may have banged it and perhaps we just didnt notice the initial crack. The handle was out of stock so it took 8 weeks before the new one arrived. This week the freezer door handle cracked! Same problem - cheap plastic handle connector doesnt withstand the vacuum seal. Whirlpools handle connection to the door is comprised of a 1/8th inch thick by 1/4 inch square piece of brittle plastic. This is screwed onto the door. In reality this needs to be metal. Enough said… Check out the handle connection before you buy this appliance. You will wait months for replacement parts as they cannot seem to keep enough of them in stock.