I have the Cabrio model WTW6400SW2. I have had it for 5 1/2 years and have been happy with it up until several months ago. The F1 would come up when the machine would lock and just start to fill. I could pause it and start it again, and it might do this 1 to 3 times. It would also do it on the rinse cycle. I have been using it because I did not want a repair bill right now. The machine was also starting to make noise when it was spinning. Well, I just happened to break my dryer yesterday so I thought I would get the washer fixed also. Well, the repairman said that the controller would cost $200 for the part, and then he said the pump roller and bearings were going. By the time you add on labor, he said, “You might want to buy a new one.” He told me that Whirlpool has completely changed the washer now because of all the problems with them. He told me to look it up on the computer, and maybe there would be a class action suit. After reading some of the reviews, I will not buy another Whirlpool again.

Purchased a new Whirlpool Energy Smart 50 gallon water heater from Lowes to replace our existing old one that had gone bad. Never again!! Had it professionally installed by one of Lowes installers. I have no problem with the installer.... the water heater was a piece of junk. From the first day we had sporadic hot water and to get that you had to have a hot water tap turned on full force. If you turned the tap to a lesser flow you got cold water. Couldnt get a hot shower at all. Contacted Whirlpool customer service 4 times by phone and 3 times by email. Horrible !!!! If I had read all the reviews ahead of time I would never have purchased a Whirlpool water heater. Each time contacting their customer service I was informed I had a plumbing problem... probably a cold water line was feeding into my hot water line??? Really??? After living in this house for 20 years all of a sudden I have a cold water line magically connect itself into my main hot water feed? I even set the temperature up as much as it would go. Could easily hold my hand under the hot water without getting burned. Most of their phone reps sounded like they were reading from a check list sheet and no desire to actually listen to what I was telling them. One even sent me a PDF file via email that had nothing to do with the problem I was describing to them. I finally told them after two weeks of this that I couldnt live with this situation and they said Well our technicians are 38 miles from you and we wont send one that far to check it. Asking what I could do they said Id have to hire someone (they werent able to tell me if I should hire a plumber or electrician) and Id have to pay for it and they would reimburse me. Sensing that this might be a fruitless task I resorted to calling the Lowes store where I purchased it and asked their advice. They offered to send out the original installer to check it out and work with Whirlpool over the phone. Like I said, I have no complaints with the installer, he was fast and professional. I stood there while their technician/customer service had him go through a few tests on the unit. All of that proved nothing except in their minds that nothing was wrong with their unit. He got off the phone and told me They refuse to accept any responsibility for the product being bad. I asked him what was I supposed to do. He got on the phone with the manager of the Lowes store and they agreed to swap it out at no charge to me. I of course was very happy but told them after all of this I didnt want another Energy Smart type water heater and that I didnt trust the electronics at all. He agreed to swap it out for a regular type and give me a credit for any difference in cost. Had this all done in one day and am very pleased with Lowes commitment to customer service. The new heater (still a Whirlpool sad to say) appears to be working fine just like my old one did. So much for it being a problem with my plumbing. After reading all the complaints about Whirlpool water heaters, I guess Im not looking forward to much of a life expectancy with this one and Im certainly not even going to attempt to call Whirlpool customer service if I do. This whole thing cost me $700 and as far as Im concerned Ill flush $700 down the toilet before buying another Whirlpool product. I still would love to know how any person with half a brain could tell me I had a plumbing problem when all that was done was removal of an old water heater and replaced with a new one. Thats two pipes people...cold water in, hot water out. I see that there was some type of class action lawsuit filed against Whirlpool. Maybe they need another one filed or forbidden to sell water heaters ever again.

I had the junky gas water heater for two years and cant keep the thing lit. Calling Whirlpool does no good. They give you the runaround; the store cant do anything. They know they have a faulty product and keep selling it. Some companies are only out for the money. If that wasnt the case, they would discontinue the junk. They will send you replacement parts but if you know nothing about them, you have to put out more money for someone to come and fix it. I would love to send them the bill! I would not recommend this brand of anything to anyone.

We owned a Whirlpool Duet washer that went out in late December 2011. We bought another Whirlpool Duet washer on January 8, 2012. On July 31, 2012, it stopped working with the error message F24. In WV, Whirlpool contracts their insurance/warranty through ACE Appliance. We scheduled with ACE the next day. They came out on August 6, 2012. The repairman told me it would be 7-10 days for the part. The part was on back-order, so in reality it took 17 days before they returned. It was repaired on August 23, 2012. Today, September 17, 2012, the washer stopped working again with the same error: F24. Whirlpool will do nothing to replace the washer, even though it is less than a year old and we paid $900 for the washer. This is the second Whirlpool we have owned that has crashed. I have two small children (4 and 2) and I am due with number 3 in 3 weeks. While the washer was broken, I spent nearly $80 at the laundromat for washing only - I carried baskets of wet laundry home to dry. And now I get to repeat the same exact struggle less than a month after it was fixed. When asked, the customer service rep told me that no matter how many times it broke, all they would do is send a repairman. They never ever replace appliances regardless of the problem. I am unbelievably frustrated and I want to tell everyone that I possibly can to stay away from Whirlpool appliances! Do not buy them new! Their manufacturers warranty is a joke!

We bought this unit (Whirlpool fridge #WRF555SDF201) in November 2016. Was so excited! The fridge looks great, love the French doors, and the freezer. Its the ice maker! It spews crushed ice all over every time it is used. Its like the setting is stuck in-between crushed and cubed. Every time it is used ice goes on floor and I have to clean it up. If a small child uses it they get ice in their face and down their shirts. I have been told from Whirlpool and Lowes that it is in the design and they will not even try to fix it. They will definitely not replace it. Lowes claims they know about the way Whirlpool designs their ice makers and that they mention it to prospective buyers, but I know they did not tell me of this design flaw in the product before we bought it. I now simply have to deal with it. It is less than a year old and I burn with disappointment every time I use the ice maker. I am even more disappointed in the lack of concern for me, the customer. We bought 6 Whirlpool appliances at the same time from Lowes about 6 months ago. It will take awhile but they will NOT be replace with Whirlpool or purchased at Lowes.

I am a Licensed Plumber in Oklahoma, have been for 25 years. Our company will no longer work on Whirlpool water heaters, heres why. I diagnosed a water heater that the pilot would not stay lit, the thermocouple was bad. Whirlpool Tech Support told me to go to Lowes and buy the parts and send them the receipt and they would reimburse me. The customer was furious that I charged them for the part and I told them when I got reimbursed, I would send them the money. Well, I not only never got any money from Whirlpool but I never got paid from the homeowner who was mad at me and I didn’t even sell it to them. Beware, buy Rheem.

Another person with problems called this a giant Whirlpool paperweight and he is so right! I received delivery of a Cabrio WTW7800XW3 washer on December 17, 2011. I had an issue (stopped in the middle of the cycle and flashed the letter “F” on the control panel) with it on January 2nd. I called and scheduled service. I had unplugged the machine and a few days later I replugged it and it started to work, so I cancelled the service call. In March, the problem started again. It just adds a little bit of water and then stops. Since then I have had repairmen out 6 times with 8 new parts installed and the washer still doesnt work. Now, the control panel won’t work. Whirlpool refuses to replace the machine. The repairman says these are the worst machines (any of the ones that are top load and have a clear top) he has ever seen and that I should buy an extended warranty. He says the bearings in the tub wear out among other things. On one of the repair visits, the serviceman found a chewed up pair of baby pajama pants. The machine makes a really loud noise like a jet engine taking off whenever it spins and the clothes are not clean. Whirlpool says that the warranty does not cover replacement of a defective machine. I have since researched the machine and have discovered that there have been problems with this line of machine for years. So, why are they still selling them? I am hoping for a class action suit. The company should stand by their products. I will never purchase a Whirlpool (or any other brand manufactured by Whirlpool) product again. I have had the machine for 4 months and it has been usable for about 2 of them.

I purchased a Whirlpool over the range microwave (model WMH3205XVQ) on 9/27/10 and have replaced the door now for the second time due to the plastic cracking. I also discovered today that the plastic has again cracked on the vent grill and the control panel. The door, vent grill, and control panel were all replaced on 8/19/2011, under warranty. It appears to me that Whirlpool has a manufacturing defect which they need to address with the consumers who have purchased these products.

From the beginning, we were not really happy with the performance of the machine, which we felt was not cleaning as well as it should. Now it doesnt take the soap at all. The washing process goes on perfectly but without soap, so the dishes remain dirty.

I brought a Whirlpool refrigerator on 2/15/2020, French doors. Bottom freezer. I have had issues with the bottom freezer from day 1!! Ive had gaps in the gasket seal and air was coming from the freezer. This happened 3x. Now there is a build up of frost and ice. STAY AWAY!! Ive never had any issues with Whirlpool until I purchased this updated refrigerator. I should have stuck with my regular top freezer refrigerator. No issues!!

I made the mistake of buying a whirlpool product and was wondering if there is a support group for angry unsatisfied customers? I have owned a duet washer and after 2.5 years is giving F1E2 error and is junk.

I purchased Whirlpool Duet HT front-load washing machine with model #GHW9400PLO. After a year of owning the product, failure codes continued to appear. I have followed the direction under the troubleshooting page which said to cancel and unplug the unit. After doing this over and over, I finally took the top lid off to inspect the problem. A ribbon cable was torn due to the top lid rubbing against the lid and the drum. I called Whirlpool and this was not covered (go figure). I then asked for the ribbon cable and they said they cannot just supply the ribbon cable and that I would have to buy the user interface which is $191 plus a $35 core fee because they re-bill them. What a rip off. A ribbon cable from a computer store would only cost $10.00. After that repair the Micro Machine control went out which is code F11. Code F11 is all over the web because this is a defective part that Whirlpool should do a recall on but why do that when they can charge $310 plus, get this another $35 core charge because they re-bill them? If you are not mechanically inclined with these parts plus labor you could have bought 2 washing machines. But who in the world would buy 2 pieces of junk right?Bottom line is: do your research and buy from a company that will stand behind their product because Whirlpool will not! They know by the number of parts they ship out that that part should be recalled.

DO NOT BUY THIS MACHINE. Mine is less than 2 years old. First one month after warranty expired, the clear lid cracked...$350 to replace! Then a few days ago a rusted circuit board came apart and jammed up my washer. This should NEVER happen. I contacted customer service and they told me that they are not covering this problem and that the service call is $175 and cannot estimate the repair cost. They also could not send a repair person out for 5 days. The washer has not been repaired yet so I do not know the entire cost but it will be expensive!

We purchased our Duet in July 2010. It worked great until two weeks ago when the washer sounded like a 40-year-old washer. The bearing sounds like an extremely high-pitched “wrr”. We can hear it in the back of the house. I looked online to get parts and noticed that you cannot replace the bearing. You must replace the entire rear drum ($358.00). This does not include the labor. I talked with a technician, and they said the whole drum must be removed, not a one-man job, and to take the whole thing apart. Now, theres no price for installation. Lets go low ($200.00). Probably more. I cannot get a price nailed down without a visit. Now add those together ($558.00), I could put almost $600.00 into a washer that this could happen to in another 2 years. Wow.We had a washer that lasted us 15 years without any parts. Is there anything that you can do to help me? This is totally outrageous. Please help. Thank you. This was part of my chat to Whirlpool. Whirlpools response was I understand your problem but cannot help you. It is out of warranty. No help, no discount, nothing. I will and have all my friends never to purchase Whirlpool. This is from a so-called American company. Im very disappointed.

Bought the Cabrio washer in March 2011. Have had the same problems as everyone else. The machine is constantly off-kilter, does not wash well due to lack of water. Sounds like a freight train when spinning. Bulky clothes dont drain properly and have to be rinsed and drained a second time. After one year of ownership, the entire control panel had to be replaced. The next year, the same control panel had to be replaced again plus a water valve had to be replaced. Thank God I bought the extended warranty. The repairs would have cost me $1000, more than I paid for the washer in 2011. Total piece of junk. AVOID AT ALL COST!!!!

I purchased my Cabrio Whirlpool washer 4 years ago and have had problems every since I bought it! Thank goodness I bought the extended warranty! The last two repair bills were over $1000 each! My warranty just ran out and I had it repaired last two months ago! This is not my first complaint! When will they start listening to consumers? This is ridiculous! Now I am faced with the problem of just trashing this washer or spending another $1000 to repair it! Something needs to be done! I am warning all of my friends and family and will post again my problems with this washer on all my social networking sights! Whirlpool needs to take responsibility for their problems! I will never purchase any Whirlpool products ever again if they do not assume responsibility!

I did not purchase it, the stove came with the house. I like the flat-top... easy to clean. I dont like that any little spill causes a stain that has to be cleaned. I didnt shop for this one. Although I would have this as an option if I was shopping. Low quality would be a problem. I want my stove to last a very long time. But, I dont want to pay a lot of money for it. I have a Whirlpool, glass top (smooth top) built in stove. I dont know the model. It has 4 electric burners, of 2 sizes. It has dials to control the heat amount.

I bought a house 2 years ago that came equipped with all new Whirlpool kitchen appliances (refrigerator/freezer, stove top and dishwasher). A few months ago, the damper door in our refrigerator broke causing food in the refrigerator to freeze. Just the other day my Whirlpool dishwasher stopped draining properly. Both instances a repairman was needed and were now out over $400 for repairs and parts. I would definitely not recommend purchasing any Whirlpool appliances and I am deeply frustrated that Im having to deal with these repairs and costs for appliances less than 2 years old.

Just bought what I thought was going to be a great dishwasher. It had all the features I wanted. But, I discovered that none of my silverware would fit in the slots provided in the silverware basket. It is a disaster. The slots are so tiny that most of them are unusable. I called Whirlpool thinking that surely there was another basket I could substitute, but no, there isnt. Everyone was very polite, but the end result is that the Ill be handwashing most of our silverware. Unless your silverware has very narrow handles, forget this machine. Obviously designed by someone who has never loaded a dishwasher!

Every one of the knobs cracked where they engage the gas valve. One gas valve came loose from the manifold creating a gas leak discovered by the propane company on a system leak test. Screws came loose that hold the tracks to the base for the slide out bottom drawer. The AquaLift cleaning system is useless. Better buy some oven cleaner and rubber gloves. Very disappointed! One star because 0 isn’t an option.

We bought our house in December 2010 and the water heater (fg1f4034t3NOV) just started to give me fits. I had the same pilot light problems everyone else encountered. The person at the 877-251-1679 number gave me a good tip and that may have fixed the problem in the short-term. They told me theres a screen for venting on the bottom of the unit and to use a bottle brush after turning off the unit to clean the screen. I did this yesterday and the pilot light has stayed lit. I called the toll-free number and was told the water heater was out of warranty, but they could send me the part to fix the heater at half-price. I ordered it and they waived ground shipping. I hope to have the situation fixed soon. I’m very pleased with the level of service.

We purchased the Whirlpool Duet Sport matching washer and dryer new in 2006 from a local appliance store. The washer was around $1,000. The salesman sold us on the load capacity, telling us it can wash 15 pairs of jeans. We dont overload it, mostly because its a high-efficiency washer and doesnt use much water (Im still trying to figure out the concept of how can you clean a whole load of laundry with a little bit of water). Its very quiet, but the cycles take longer than standard washers.Also, you must use very little soap (too much soap will cause the washer to stop and display an error code, which youll have to call a technician to come and reset). It is now 2013, and the washer started thumping during a cycle and there was a burning rubber smell. We called an appliance repairman who gave us an estimate for repair of $800 to $900 (for a bad bearing/bearing casing and inner basket). Im sure that there was quite a markup on those parts! It seems to me that the older non-efficient washers lasted longer than 7 years, and certainly didnt cost $1,000 when new.

Reading the reviews on this I figured I would chime in. Same problem with the top rack, its unfathomable how cheap this was constructed, since I have had old school dishwashers 15 years old without even close to a similar problem. Bought in 2012/2013 and have had this problem on and off the entire time. Looking at a new one definitely not a Whirlpool!

Have had this washer for one year. Clothes have never been clean since day one. Dark clothes come out with white marks all over. Having to use an extra rinse cycle or set on bulky items - whats the point of a high efficiency appliance? Still not clean after that anyways. Stains such as chocolate and toothpaste still remain after washing and my husband complains of finding small holes in his clothes. Lid needs to be left open at all times or you get a funky smell. I am using the HE liquid detergent, even tried a cold water product for cold washes. I hate this washer. Wish I had my 20 year old Kenmore still.

Piece of crap! Approximately 18 months of aggravation. Clothes don’t come clean, leaves residue on them. Just absolutely the worst experience I have had in six plus decades of doing laundry. When next I get a washer...it won’t be a Whirlpool or anything made by the company. There should be recalls on these washers.

We have Whirlpool dishwasher for almost 10 year, very happy with the performance. This dishwasher is very quiet and also very spacious. The look and the price compared to other model is compatible and I will recommend it to other household. Thanks.

I bought a matched set of Whirlpool washer and dryer. Within about 3 months the dryer quit running on any of its cycles except heavy duty. About a month after that the washer started messing up. First it quit putting in the bleach. Next it quit adding water except under the heavy duty cycle. Then after about another week or so it quit putting in fabric softener. After a couple of more months it only uses hot water. Now not quite a year after I purchased it the washer now only adds water in the wash mode and not the rinse cycle. Now all this would not be a problem except I had lost the warranty cards and in their website would not let me register it online.

We purchased a Whirlpool Water Heater at Lowes - model no. FG15040T3NOV, serial no. 0434120861, product no. 0730267 & weve still been having issues keeping the pilot light lit. We purchased the bottom unit piece that Whirlpool said would fix the problem but weve still been having problems with the pilot light going out. The water heater isnt under warranty anymore, so last night was the last straw & we finally decided to get another water heater that wasnt a Whirlpool. Ive done a research on the internet and found out that a lot of consumers are still having this problem to this day.

Tried for several days to schedule service call for my leaking whirlpool ref/freezer. Waiting on hold to speak to a rep... transferred to another dept. - on hold again listening to a recording advising me of the unusual high volume of calls to call back at a later time (should have been my clue of all the problems with their product). I had three different Whirlpool phone numbers given to me from the reps I spoke with. I would like a refund for my extended warranty. I have called an independent service company and will pay for the repair. I will not buy or recommend Whirlpool or their products.

We purchased this washer on 2008-04-27. It ran okay until a few months ago when it began making strange intermittent noises. This is now happening more and more often. I reviewed a lot of websites and see that this is a common occurrence for Whirlpool Cabrio washers, and Whirlpool will not stand behind it and make it right. Im going to write them a letter mirroring what Im saying here, and remind them that other appliances in my house are coming due for replacements or upgrades. Whirlpool and its affiliates will not be part of those upgrades going forward. I have no patience or tolerance for expensive **, which is what they put out here. I will have to purchase a replacement washer since this seems to have two major areas of failure, both extremely expensive to repair. I might check out Roper and see what they have--its apparently very well rated by the folks that work on these things.

BEWARE THE TEMP CAN BE 25 degrees off high and 25 deg lower and Whirlpool says that is within specifications. My oven temp was set at 350 and nothing was cooked... After 7 repair calls with their certified repair companies (the 2 worst repair companies that I have ever used) I was told that if you set your oven at 350 that if it stays in between 325 and 375 that Whirlpool claims that it is working fine and will not do anything. I called and talked to customer service and asked the lady that if you set your oven at 350 should it stay within a few degrees of that and she said YES.The people that work at Whirlpool do not even know what kind of junk that their company is selling. I asked to return it and get a more expensive model hoping that it would work better but they said that they sell ovens and do not buy them. Be sure to get in writing from your sales person that your oven will constantly hold the temp within a few degrees. I tried to do the Whirlpool survey but after 11 attempts they said that there was errors in receiving and they did not get it. If you buy Whirlpool then you did not ask the right questions. I WILL NEVER BUY Whirlpool again (unfortunately I have a Whirlpool dishwasher and refrigerator that are not much better) and if you do you will say the same things and be out Thousands like I am.

Ive had other brands of washers and dryers and I must say I always return to Whirlpool. They are well made and do what they are supposed to. Never had problems. My last set of Whirlpool was about 12 years old. Great product.

Have an old Estate by Whirlpool, still going, no problems, washes well. I can control the wash by adding more water, stopping it and restarting it. There is nothing like the old washing machines. I have seen and used the latest and greatest, but they cannot compete.

I like the fridge raider. It works great, I have had no problems. It has good space in the fridge raider part, but very small freezer. It’s a freezer onto fridge raider on the bottom. I would like more space in the freezer area. I would buy another Whirlpool.

Like many other reviews Ive read here this morning, I bought a Whirlpool Cabrio HE Top loading washer before I did my homework. I purchased approximately 2 years ago. While I dont seem to have the volume of complaints Ive read from others, I do have many intermittent complaints. As others have described, from day one I have gone from this uneasy feeling about how it is working to down right POd about the condition of my clothes after a load finishes.List of issues you will avoid by buying a different product: 1. Water levels SO low your clothes dont get clean. Yes Whirlpool, thank you for trying to save me $$ by lowering my water bill, but for goodness sake there should be enough water in the damn tub to cover the load. I literally watch dry clothing twist back and forth and NEVER go out (like they claim) to the edge of the tub and under then back up in the center. Instead they just sit there watching from the edge while the poor items of clothing in the center get twisted together.2. Powdered detergent, even if listed as HE will not dissolve in this low water level and will end up as white patches of film on your dark clothes. Suggestion to avoid this - dont use powdered detergent, but even if you use liquid HE detergent, you may still experience white patches of soap film on your clothes. It happens on all of them but shows up clearly on dark clothes. Setting the washer to always do a 2nd rinse cycle will improve the outcome. Not a perfect solution since the point of a low water washer is to use LESS water and not more by running a 2nd rinse on all your loads.3. No Consumer/User options to allow you to use the washer as you see fit. Since I paid a small fortune for this stupid washer and didnt realize that I would never again be able to dye fabric in my washer I am posting this as a warning to other crafty consumers. DONT BUY THIS WASHER if you ever want to dye fabric or an article of clothing larger than underwear. There is absolutely no setting on the washer cycles that will fill the tub with more than a few inches of water. The washer falsely has a mislabeled setting called Deep Water Soak. This is absolutely a LIE. Good thing I tested the cycle before putting my blanket in there to dye it. The cycle spins many times in the beginning pouring water into the clothes, then empties the tub and does it again. Then after 10 minutes into the cycle it begins to fill (if you want to call it that) the tub.After putting about 3 inches of water in the tub - not even enough to cover the top of the articles in the tub (I used 6 towels as my test subjects) it stops to soak. But stuff is still sticking up out of the water!!! OMG! So frustrating. This would not do for dyeing anything of value as you would not be able to agitate enough to ensure coverage of the fabric evenly with dye. Just dont buy this washer if you have, as I have in the past, enjoyed changing the color of linens and re-dyeing dark clothing that have faded! Whirlpool clearly didnt care about how consumers actually need to use the washer. I may try using this setting by pausing and filling it manually with buckets of hot water from my sink to get enough water in there to cover the fabric. Its just ridiculous that I even have to consider how to outsmart my washer!4. Smelly clothes. Seriously. I do the obligatory monthly Affresh cleanings, and I have learned to leave the lid open after the last load of clothes so the tub can air dry. However, I still from time to time pull a load out of the tub and it smells like mildew. And dont think for one second that the smell will go away when dried. I have opened the dryer and pulled clothes out, smelled the mildew and put them right back in the washer for a 2nd go round. Nothing worse than putting on a clean nightgown and smelling like mildew! Ewe!! With this awful washer you can NEVER leave a load of washed clothing sit for any length of time or you can look forward to smelly clothing. Hate it. Absolutely HATE it. Again, this defeats the purpose of using less water.Cant make myself spend more dollars that I dont have in the budget to replace this piece of crap. I have figured out all the workarounds for now, but as soon as I can replace it I will send it to the dump. Not going to resell or donate to anyone else as it would just be a burden for others. If there was ever a rightful need for a class action lawsuit to compensate consumers for false claims by a company - this is it! Hope this helps prevent anyone reading from making the poor purchase decision I have!

Cabrio Washer - I am so disgusted with this product. After only a few months service came out and the repairman told me it was normal for a load to run for 8+ hours. Second repairman replaced the circuit boards and it has lasted 11 weeks. Now it is not working again. Calling tomorrow. I have a bad feeling about what the end result will be. Expect I will be buying a new washer, will not be a Whirlpool. Just went and tried what another reviewer does to get it to run... Pause/start/pause/start. After 8 tries it is now running. I will not live with this. Not going to spend a dime to fix this piece of garbage. Still have 36 days left on extended warranty.

Own Whirlpool GB2FHDXWS04 refrigerator for 14 months. From the beginning, the ice maker made gross tasting ice and never got better (had to start buying ice). Then a smell started coming from the fridge every time the fan came on. We called before the warranty was up and talked to Whirlpool, and they said that we must have put something smelly in the fridge that caused the plastic to absorb the smell (which we didnt). They told us to put baking soda in and change it everyday. No change. They kept telling us there is no way it could be giving off a smell for any other reason and if they sent a tech out, we would have to pay for it. Trying to intimidate us until the warranty was up. Then after a month or so, the bottom mount freezer starts leaking water all over the wood floors every 3 days. At first we turned off the water line, but then realized it is coming when the freezer defrosts. One good thing, the freezer, from the beginning, knocked really loud and now that its leaking it doesnt knock. We spent $1,200 just over a year ago and will probably have to go purchase a new one now. I will tell you it will never be another Whirlpool product. Whirlpool has not apologized or done anything but say, Now your warranty is up, you should have bought the extended warranty. Great customer care! With all these same complaints, you would think Whirlpool would figure the problem is their inferior product (which they know) and actually take responsibility.

I own a Whirlpool Cabrio. I wanted a newer technology (no agitator) washer with top loading capabilities. I ended up with a four to five-year lifespan with this washer. The bearings are busted and it leaks water from the bottom. I have followed loading instructions specifically. It will cost about $1,000 to fix so of course, I am buying another washer and a matching dryer.

Just had the repairman at my house to repair my 2-year-old Whirlpool refrigerator Model GB2F4DXWS07 - he couldnt fix it. Just throw it away and get a new one. There is a blockage somewhere in the line, he suspects the lines were not cleaned before it was charged at the factory. Repairman said it was a typical 20-year-old refrigerator problem. Customer service was no help - Whirlpool live chat is currently unavailable. Lousy product with worse service. I will never buy another Whirlpool product.

This is a top loading, with agitator, purchased from Costco over five years ago. It took some time finding a top loader, which I will always prefer. Very reliable. Have only needed repaired once. Have other Whirlpool appliances, very reliable.. Fridge over 20 years old and no problems, except needing new ice maker. Also, other whirlpool washer we had over 15 years.

I purchased a side by side Whirlpool refrigerator in December 2009. In one year’s time, all of the plastic shelving has completely broken. The repair man said that he felt like the plastic was substandard and to call Whirlpool but they said that we must have abused the shelving.I and my husband are senior citizens and the only ones using this refrigerator. How can all the plastic components break within one year? I had my last refrigerator for over 10 years and I gave it to my son. It is still running and all the plastic shelving is still intact.I feel Whirlpool should fix this problem but they do not care about their customers. Once they have your money, you are forgotten. In the end, they will be forgotten because I advise everyone I know not to buy from Whirlpool.

I purchased a water heater Model # UG1H50400TBN, Serial # 0913T400920, from Lowes in Corona, CA. 05/07/2009 for $528 plus tax. I have replaced the following parts: 02/10/2010 Thermostat Valve, 07/23/2010 Thermostat Valve (2nd time), 08/10/2010 Burner assembly, 02/10/2011 Thermocouple, 02/17/2011 Thermostat Valve (3rd time), 12/17/2014 Thermocouple (2nd time) and 03/20/2015 Burner assembly (2nd time).Today I called WHIRLPOOL Customer service (877) 817-6750 because my water heater water is warm. I told the tech support agent that the pilot light was on so we agreed that it was the thermostat valve AGAIN. He wanted $30 for overnight delivery and I refused to pay. Now I have to go out and buy this part because Whirlpool like the Banks is too big to fail and they have license to RIP-OFF the consumer without penalties. Whirlpool has all of information and they can verify everything I wrote here just by the serial number.

In January 2021 I purchased a front load Whirlpool washer and matching dryer. They were delivered on February 6 2021. The first load we found water on the floor. I thought I didnt close the detergent drawer so I proceeded with the next load. Again I found water this even through the ceiling tile in room below. So with the next load I sat in laundry room to see what was happening. When on the rinse cycle water shoots out the front of the dispenser drawer.Contacted service, they sent repair man. He ordered new parts and I waited over 3 weeks for next repair call to find out that whirlpool had part all along. Repair man came again and still no resolution to issue. He was told to order same parts again - still no resolution yet again. I fought with Whirlpool till they said they would give me a new machine. Now fighting because delivery people wont uninstall 1st washer and install new machine. Today is June 28 2021 and I still DONT HAVE A WASHER TO USE. I havent even used the dryer yet. I have $3400 and numerous hours with Whirlpool trying to resolve this issue! Can you help? Whirlpool continues to string us along, telling us to be patient, theyre doing their best.

If 0 stars was an option, I would have chosen that. Ive had my own home for 34 years and have had many washing machines over the years. My Whirlpool Cabrio is absolutely the worst washer I have ever encountered. It doesnt get clothes clean and constantly gets out of balance. Whirlpool did a service call and said it is functioning as designed so I was unable to get a replacement. I really hate being wasteful and adding a huge appliance to a landfill but I will be replacing this machine as soon as it fits into my budget. I dont have a receipt to submit because it was purchased by my builder at my request. Do not buy this machine!

It gets the job done. Its no power washer, but the dishes get pretty clean and dry nicely. I have no idea how dirty the dishes can be and still get cleaned, since Im weird and pre-wash my dishes. Its stainless steel and black, and has quite a few wash and dry settings, including an option for heated or unheated dry. The utensil rack is attached to the door of the washer and cant be moved. Two levels, and pretty easy to do dish tetris with. No offense to most standard dishwashers – I need a washer about 3 times the normal size due to a passion for cooking. Its slick and matches my ultra-modern, borderline-Swedish interior.

We purchased this machine new less than 6 months ago. We found that it is not cleaning our jeans. We cant even work cattle and get our jeans clean. I called Sears and Whirlpool and told them it does not clean our jeans. They said it was under warranty and that they would come out to see if it was working properly. Well they said it was and then sent us a bill for $77. They said Customer Instruct was not covered under warranty. I already read the instructions and I knew how to operate this machine. The technician said this is not the first time he has had this type of complaint. Anyway I am VERY dissatisfied with this washing machine and I want Sears and Whirlpool to take it back and give me a better machine. I want one that can get clothes clean. If you are satisfied with dirty clothes then I guess you will like this machine.

Water heater was defective from the factory with a pinched wire between the thermostats. After replacing everything on the heater Whirlpool would not reimburse any parts or labor for the unit... Whirlpool is dead to me now, and forever and I love to tell my story to prospective buyers of their products!!! So far, to date I have cost them about 14 sales of major appliances (and still counting!!!). After reading some reviews… Im (sorry, I omitted the personal insults) in respect of your review guidelines.

We purchased a Whirlpool Cabrio Washer in 2010. I have had nothing but problems trying to wash black/dark clothes, it leaves white stuff. I assume its soap scum all over the clothes. Ive tried cleaning the machine with Refresh more often than recommended and it still has the same problem.

Whirlpool, shame on you! I purchased my Whirlpool Cabrio pair from Best Buy in 2008. Ive had repair technician after repair technician out over 7 times! The washing machine must have been designed by a 3-year-old! Whirlpool, youre getting greedy and youre making your products CHEAP! I know this is fact, I have a 15-year-old side by side in my garage made by Whirlpool and it works great! Fire your 3-year-old designer! I will NEVER buy Whirlpool again! After all said and done, this pair has cost me total purchase and repairs over $4,000! And Now my bearings are bad! Thank God for YouTube! Im fixing it myself this time!

I bought a Whirlpool Cabrio Platinum washer 2 years ago and it is by far the worst washer I have ever owned. Its a water saving device with extremely long cycles. The clothes dont get wet enough, dont come out clean and they do not smell fresh. I have to put them through 3 rinse cycles and often times have to re-wash my clothing. The cycles are very long, using more electricity, and it takes me 3 times as long to get my weekly laundry done. My clothing comes out more wrinkled and twisted causing longer time ironing. My old agitator style washer did a superior job compared to this piece of junk. I dont like the automatic locking lid, nor do I like the machine choosing the spin cycle for me. There isnt even a soak cycle. If I want to soak my things I have to do it in the sink and then drag them to the washer to rinse and spin them.I spend a fortune on laundry additives in order to get my clothing clean and then they arent as clean as with my old washer. I now dread doing laundry and every time I look at the washer I feel like taking it to the dump! There isnt anything I like about this machine and I wouldnt recommend it to anyone. It is a piece of crap. This is 2016 and they havent learned how to make a good working washing machine. When I move, I will be celebrating leaving it here! I will never, ever buy a product made by them again.

The repair technician just left telling us that our Whirlpool Cabrio washing machine is fine. It is a little over a year old, makes LOUD noises as it runs, doesnt get the clothes clean and often doesnt even get them wet. The clothing sits above the water and comes out with pet hair, soap and dry spots. We use it the way the manual directs but it seems to be a totally defective machine. We sure wouldnt sell it to anyone nor give it away to some poor unsuspecting soul. Guess it needs to go to the dump. Shame on you Whirlpool for taking advantage of so many of us.

UL code displayed for six months. Will not spin. Makes a squeaking noise. Recently noticed a black greasy residue around the machine. The bottom of the machine is covered with it. Have had the Cabrio for 5 years. Seems like a bearings issue. Expensive machine. Whirlpool said there are no reported issues with my model even though there are thousands of people on several websites who are having the same issues. Apparently, Whirlpool is in denial and not willing to save face with consumers and correct a horrible washing machine. Definitely will never purchase another Whirlpool appliance.

Purchased Whirlpool refrigerator at Lowe’s. Refrigerator would never get cold enough, so I exchanged with a Whirlpool Gold side-by-side refrigerator. After installation coffee was spilled behind refrigerator. I was unable to pull refrigerator out from wall to clean coffee spill from behind. When checking with Lowe’s on the 35th day, I was informed that Lowe’s 30 days warranty had expired and I would have to work directly with Whirlpool.I discovered it was very hard to communicate with Whirlpool; there was a problem that they only had on file the first refrigerator I purchased not the one I kept. The Whirlpool service rep did not seem very cooperative but with insistence they told me they would change my information to the correct model and serial number and a repair order was sent to a local service shop. The problem with not being able to roll the refrigerator out from the wall is that Whirlpool had changed their wheels to a tri-wheel support and there was not enough height on the single front wheel to lift the refrigerator to clear the screw down leveling stops on each corner. The service rep had no solution for the problem and had to call the Whirlpool service. He indicated he never was able to get assistance from that department. I told him I would talk to them as the consumer but they refused to discuss the matter with me, so I gave the phone back to the service tech. Whirlpool told the service tech to order replacement wheels of which I knew this would not resolve the problem.After two weeks, the replacement wheels arrived, the service tech installed them and as I expected they did not resolve the problem. I then requested the service tech to remove the rubber from the stops on the corner to allow for the additional required clearance and this solution worked. This is a very poor design for Whirlpool, but I accepted the results. Two weeks later I receive a phone call from the service business and they tell me that Whirlpool did not have the refrigerator model/serial number they worked on. Whirlpool was not willing to resolve the problem I had with them initially and the service business would have to bill me directly and was not covered under the warranty.At this point I lost it and informed the service business I resolved this model/serial number with Whirlpool before. Whirlpool gave them the authorization to work on the refrigerator and they would need to collect the fees from Whirlpool. I have purchased my last Whirlpool appliance mostly because Whirlpool makes it very difficult or refuses to talk to the consumer and it appears the quality is no longer there. Will Whirlpool become the next Kodak? With this kind of service, people will just quit buying from them.

We purchased a Whirlpool Gold self-cleaning oven three months ago and have had nothing but problems with it. First of all, the new aqua clean system is a joke. I ended up scouring the inside with cleanser and a scouring pad for over 30 minutes to get all the baked-on food that the aqua clean system did not get off. Now Im not wanting to use the oven to cook anything that splatters. Secondly, the oven does not cook when using the convection mode. I thought convection was suppose to cook quicker but in my case, I have to cook the food longer. Thirdly, the bulb burnt out in the oven after only three months. Im glad we are trying to sell the house because I could not live with all the problems very much longer.

Purchased the Whirlpool Cabrio washer January 2010. Purchased the extended 2 year warranty from Lowes. After about a year I noticed around the bleach dispenser it was starting to rust. Over some time it worsened and grew bigger around all sides. I was unhappy about it, but thought it was just cosmetic and didnt pursue the issue. Now it must be on the inside and has started putting yellow spots on all of our clothes. It was only a towel or two at first and now it is on everything. I called Whirlpool and Lowes customer service center and they are just sorry and will not do anything. Lowes warranty does not cover any rust whatsoever although I cant find that stated on the warranty papers. I will never buy another Whirlpool product, ever. $600 for a washer and $70 for an extended plan to last on 3 years. I know people who have washers for 10 or 15 years. Im so disappointed.

We bought a Whirlpool front load about six years ago. We have had nothing but trouble with since we have owned it. First, the sensors went out on it. We had to pay over $300 to have that fixed. Then, it wouldnt run right. We had to pay another charge for that. Now they tell me the water valve is bad on it. If I had known at the time the problems I was going to experience with this washer, I would never have bought it. I fell for the price. We paid for it. We should be getting better service from it than we are. I could have bought 6 regular washers for what I paid for this one that doesnt perform like it should.

WTW8000BW0 washer - This is the worst washer I have ever brought. We bought a pair washer and dryer. The washer started making noise when it was in spin cycle so we called repairman. He came and said it would be better if got rid of it and bought something else. Said it would cost too much to fix and hes seen too many of these. The noise is so loud we close door on laundry room and we cant hear TV in front room. This is the worse junk we have ever brought. Whirlpool should be accountable for this.

I have the model FG1H5040T3NOV water heater and had found this message board. I called the number posted by Chris with American Water Heater and provided them with my serial number. They shipped me the replacement assembly next day and after about an hour, I had it installed and working again. Im not too happy with the fact that it failed, but it does appear they have their act together in getting the replacement parts distributed.Based on the discussion with the person on the phone, my only real gripe is this: the cause of the component failure was potentially caused by a dirty-flame trap that supposedly needs to be cleaned regularly. Since the trap is underneath the water heater and is in no way really accessible, relying on people to see the fine print in the manual (which hardly anyone reads) isnt sufficient. At an absolute minimum, a very clear and apparent sticker should be included on all water heaters indicating this needs to be cleaned and a clear description of how to clean it properly to prevent this sort of unnecessary headache in the future.

I purchased my Cabrio a little over three years ago. Within the first month, the computer board had to be replaced and the tech informed me that it was not a malfunction in the unit; rather, it was because I did not have a sock bag for my socks and panties. I replaced the board, bought a sock bag and had no problems for about 1.5 years. A little over a year ago, the un-level started. I did research and found that I needed to replace the rods and add couplers as they were not thought of when the unit was created. This worked for an entire month. Now, I am in the same position again. It takes about 6 tries per load and the amount of water I am using is increasing with each failed attempt to wash. There should be a recall on this product. I notice there are many other complaints that match my frustrations exactly.

2016 Cabrio Washer - I had an 11 year old Maytag washer that finally gave up so rather than go through the repair I decided to upgrade to a new washer dryer and went with the Whirlpool Cabrio W/D pair. I am shocked at the washers inability to clean even the most basic of stains. I have to pre-treat clothes like never before, have tried every type of wash cycle offered and cant believe the amount of time it takes to clean clothes. Over one hour??? My Maytag may have agitated the heck out of a load but in less than 30 minutes everything was clean. Ive had to re-wash load after load of the most basic everyday stains. I was hoping the larger drum would allow me to cut my laundry time down but that is not the case, and find myself putting a few things in at a time so they get washed. Im stuck with this piece of crap and have only had it for one month... Cant wait for it to start breaking down and dealing with repairs as so many of these comments mention. I miss my Maytag!!!

My Whirlpool refrigerator is more than a year old but have been complaining forever it seems. The serial # is 21142009, model WRT777REYWOO. All bottom cords etc. is out and 3 times I had people come out to fix and it never changed. The lettuce drawers freeze and in the freezer leaves ice cream pretty soft. I am so upset about this, and cannot afford a different one, no matter what brand because I paid around $1,000 for it and I am low income (my ss), 73, and disabled. But Whirlpool refrigerators are not worth buying if this is the standard policy to ignore their responsibility here. It leaks water from freezer to meat compartment, and I could go on but seems hopeless. My sister in Oregon had the same one and they took hers out finally so she could apply that amount to a different brand which has no problems.

WHIRLPOOLS unacceptable customer service! Less than one year ago, we bought a Whirlpool dishwasher, type ADP 4411 from Khoury Home, Lebanons leading retailer of household products. From the beginning, we were not really happy with the performance of the machine, which we felt was not cleaning as well as it should. But the nightmare for us came when ten months later, we came home to an electricity burning smell and smoke from our Whirlpool dishwasher, which had been off. Thankfully, our electric security system in our new apartment worked very well and shut off, so that our apartment didnt catch fire. It was a shock, but knowing that our machine was still under warranty, we contacted Whirlpool to let them know what happened. The bigger shock came when the company told us that the electric board is burnt probably because of high voltage when the electricity came too strong one time and that we have to pay for a new board $190 because such cases are not covered by the warranty! A Whirlpool manager said because the electricity in Lebanon is unstable, we should have unplugged the dishwasher whenever it was not in use - but its not really logic- the same thing can happen while it is in use (and of course nobody told us about it when it was installed)! We, like other normal people, do not unplug our appliances when they are not in use, and we are using in our kitchen a lot of other electronic appliances without any problems.The fact that Whirlpool is blaming us for a fire that could have had much more dangerous consequences is absolutely unacceptable. Unfortunately too late, we have read at the internet a lot of customer comments with these kinds of problems with Whirlpool dishwashers too. At last we got a $20 discount (!!) for the new board but on the service letter they wrote just that it had smell problems. Nothing about burning! A burning dishwasher should be for Whirlpool company a much more serious theme! The way it was handled is NOT a customer service, NOT an international service for a big company like Whirlpool and especially really NOT the customer service of a U.S. company!

I purchased a Gold Star Whirlpool Refrigerator from Sears which was installed on July 1, 2010. The freezer was icing up along seams, so sealant was used. However, now I noticed after 14 months that the interior refrigerators lining is fracturing throughout the sides and bottom of the refrigerator. Not at seams but all over fractures, spanning 10 to 3 to 2 on the bottom and side of the interior lining of the refrigerator.Sears answer is more sealant, and Whirlpool does not take any responsibility in designing a defective liner since it is pass the one year time frame. This causes your refrigerator to be on more often, because of the cracks. Unfortunately, the consumer loses out. Both representatives were nasty and when I asked for a supervisor from Whirlpool, an incident report was written, however I will not ever be able to get a copy of it. It will be considered an internal document. It is a great setup between Whirlpool and Sears having defective appliances made to last a year, and Sears to win with warranty agreements for the life of your appliance of $250, for one year coverage. When you buy the warranty and have a lemon, Sears doesnt replace it, My suggestion to consumers is to buy a tube of sealant.

Whirlpool Washer WTW8700EC + Dryer WGD8700EC. Bought to replace a 35-year-old Whirlpool set that is still working and had no repairs in that 35 years of ownership. Gave to family member and its working well. Was not a cheap item but well worth the money. It performs beautifully. I chose Whirlpool. It is a proven brand with a long history of reliability. When I bought my last Whirlpool, I bought the top of the line model washer and dryer. They say you get what you pay for and that holds true in my case as has with many others who believe it! So this time I did the same thing and bought the best top loader they had. It has many options I still need to learn. I just use it like the old machine and dont need to worry about types of fabrics or making mistakes. Just follow the instructions for detergent and softeners and all is good. This machine cleans as great as the old one without beating the clothes to death. New agitator design keeps from paddling the clothes, so I dont need to use the gentle cycle or medium to preserve the clothes. The dryer I can say is most efficient as I noticed it took far less time to dry, and notice a small drop in my electric bill and gas bill. I think this will be my last machine ever needed. I do take care of my things and I do clean and polish my machines, they are an investment like a car or house. Front loaders have a lot of problems with leaks from the doors. Will stick with top load only!

I purchased a Cabrio Top Load Washer and Front Load Dryer four and a 1/2 years ago and have had nothing but trouble with them! The dryer needs to be run 2 cycles to get the clothes dry. In that time I have had a repairman come to the house 3 different times to look at the dryer, which cost me over $200. They have had to replace the belt and inner pulley and then the sensor harness. Recently when they came they tried replacing the coils. It continues to give me trouble drying the clothes and I am very dissatisfied with it. A few weeks ago the washer broke. I have had repairmen come to the house 4 different times. Multiple times there has been a problem with the spin and drain cycle. All of the water would not empty out. I would have to run the cycle again. They eventually replaced the actuator. I continued to have difficulties with the washer.Then the machine got very loud when it would spin out sounding like a rocket was going to take off! The repairman came once again said it was the motor. When they returned with the parts and took the machine apart, the parts inside the machine had all corroded! The water had been leaking inside the machine, destroying it, and a black sticky buildup had formed! The machine was deemed unrepairable! I paid over $700 for each machine and am very upset about this. When I spoke to customer service they would not stand by their product because I didnt have the warranty anymore. After numerous phone calls I filed a complaint and gave a bad review of the support service and product that I received.Weeks later they called me and offered to have me purchase another machine at half price! I had already bought another brand washing machine and I asked them to apply the amount toward what I had spent on the new one. They would not and insisted the only thing they could do would be to have me buy their washer at half price. I told them I lost faith in their product and didnt want another one. So, I would not recommend the Whirlpool Cabrio washer and dryer, or Whirlpool products since they will not stand by them! I have pictures to prove what happened to the washer!

I bought a pair front loading washer & Dryer May this year and took Delivery in June. First problem was with touch controls. I should have Known then it would be trouble, they replaced it then we went home to Fl. - Aug. Returned in Oct - used the machine eight times total and it locked up with our Clothes inside in water. Called for service, was told it would be a week before someone could come, then was told after four days it was the mother Board and it would take at least another week to get our clothes out. Their Service is the worst I ever have dealt with. The whole house - we Bought Whirlpool based on the Maytags we bought for our House in 2004. Never a problem but those Maytags were Maytag - not whirlpool. I would never buy any Whirlpool Appliances again. It is sad because I try to buy American made to support our fellow Brothers and sisters in the work Force but now I will buy made anywhere as long as it works and has reasonable service. Whirlpool is not the same as I Remember from years ago.

My Whirlpool Cabrio cannot wash sheets, blankets or any of this size. It balls up in the middle and form a bubble and only part of the items is washed and washing powders are trapped. I have purchased more sheets in the past 4 years than I have in the past 45 years of doing laundry, because the washing powders are not washed out. I wash on second rinse also, never fails and it still does not get all of it out. The clothing gets off balance if it was more than 3 small items. I have a leveling tool that I put on it often to make sure it is level. It’s something within the machine. I will never, never, never purchase any more Sears’ product. If anyone has jury-rigged this machine to work, please let me know. Sears has refused to help me, even today.

We purchased a Whirlpool Cabrio washer and dryer set in 2013. In 11 months we have made at least 6 calls concerning the same issues machine leaving white residue on clothes. It has been one thing after another. Today the manager told me that my warranty only covered parts and not a replacement machine. I am washing my clothes two or three times to get them so we can wear them. First this is not saving water, energy, time and most of all CLOTHES. We are wearing our clothes out washing them. This is unacceptable. With this many complaints, the company has to know they have a machine with issues. I will never purchase Whirlpool again. I think we should all band together and file an action against Whirlpool. These machine cost too much money to be crappy.

We purchased the model WFC7500VW, 24” washer and accompanying dryer in June of 2015. Within a couple of months, the water pump went; also we continually had to take the front panel off and clean out the filter when we get an A11 code! Now we experienced an F06 code... This code means the washer can’t go into high speed. The repairman (Whirlpool recommended), told us that a new tachometer motor, etc would run $500-$800 with labor! He also said that the noise the drum made was bad. My dryer works fine (only complaint is the grinding noise it makes, which Whirlpool told me is normal)... I would like to purchase a new washer, but don’t know what will fit under the dryer. I do not want ANY Whirlpool product!

Stove was purchased in June, 2021. Two months later, oven will not heat up!!! Contacts Whirlpool, and TEN days later, a service person finally shows up. Problem appears to be a circuit board that they dont have, and has to be ordered! When will it arrive? He has no idea!!! I called Whirlpool, but its frustrating and a waste of time. You only get to talk to someone that appears to be reading from a script! If were lucky, well be without an oven for one month; however, it could be two...or three...or four!!! My advice: Dont buy this stove/range!!! Not only is the oven an issue, but it just seems flimsy and subpar quality, especially the oven door. Added to that, the glass top is very difficult to keep clean... Worse than any glass top stove weve had in the past.

Help? WP Gold double convection wall ovens WOD93EC0AS rated very high by Consumer Reports installed end of February. Monday April 6, fan in top convection oven came on suddenly while oven not on. When I tried setting a baking temperature in top oven to see what was going on, message read This function is not available. After about 15 minutes the fan went off, and I could use the oven. Worked well Tuesday and Wednesday. Oven not used again this week, but this evening, Friday, same thing happened again. Process has been repeated several times with fewer times between fan turn on. Have turned off power to ovens until I can get a repairman. Has anyone else had this experience or know what the problem is. Have been reading about the problems with WP ovens. Wondering if I need in addition to Home Depot Warranty the one from Whirlpool as well. Had Bosch convection ovens for 12 years then self-cleaned and thermostats went out and cannot be replaced because parts no longer made or available through any supplier. Said I would not buy Bosch ovens again because the parts became unavailable even sooner. What a mistake. Apparently self-cleaning element blows a lot of ovens thermostats and/or circuit boards. Loved the ovens and had only one repair after the ovens were one or two years old. The Bosch dishwasher is same age and still working great and usually cant even tell it is on.

Unfortunately where I live the walls are thin. And my neighbors have complained about how loud my washing machine is. I load it correctly and sometimes while it’s washing it rearranges the clothes and it becomes unbalanced and makes incredibly loud thumping sounds when this happens. I’d say 1 out of every 4-5 times. Also I have multiple towels and clothing that have been pulled. The threads of brand new towel sets ruined from the washer.

I have always used Whirlpool washers and dryers. There are many models to choose from to meet a families needs. I can only remember one time when I had to replace an operating part to improve performance.

I purchased a condo last year with all appliances included. My Whirlpool refrigerator model is GI6SDRXXY00, a fairly new refrigerator. I noticed orange and moldy spots on ices when dispensing them. I changed the filter, thought maybe it is the filter causing the issue. But after inserting the new filter and emptying the entire ice tray, I still get bad ice! I open the compartment, and surprisingly, found out that the spiral rod inside the ice dispenser was rusted! This is horrible and unacceptable! This is not a user fault but a manufacturing defect. The parts that are in direct contact with what customer consumes should be robust and safe. I contacted customer service, and they gave me a technician phone number which turned out to be a third party which only cares about money. They said they will inspect the refrigerator and will charge me $134.00. I will not use this refrigerator anymore and will replace it soon. AND I will never purchase any more Whirlpool products. This manufacturer is crossed out from my list of vendors who I do business with.

I have purchased 2 Whirlpool washers in the past 6 years. Both have been a huge disappointment in quality and dependability. The 2nd washer I bought May 8, 2015 had problems from the initial purchase. In just a little over 2 years I have had to replace the suspension rods, and now the transmission is broken. Both washers had transmission problems. I have bought my last Whirlpool products. I recommend persons considering buying a Whirlpool product check the reviews before you purchase! I cannot believe this company continues to survive.

Weve had this washer for about 9 months now. We noticed that the loads being washed small or large werent coming out clean. When wash cycle finished items were covered in soap residue and or had large dry spots where water had never touched the area. When our sheets were washed in bulky/sheet cycle and deep water this happened. Maytag sent out repair person to find the water pump went bad, pump was replaced. After repair same bad washing results as stated previously. Maytag then sent out repair person for the second time. This time the main electrical board was replaced. Still after two repairs wash loads are still coming out dirty, soapy, dry in spots in any of the selected wash cycles large or small. Third call to Maytag and a third scheduled repair date coming up in a few day. Over the phone the Maytag employee only words of wisdom was, Did you buy the extended warranty. So unless there is a third failure I believe that this washer is just a poor design.

I purchased this range 7 2013. I was a snowbird at the time so after November I went south. Upon returning my top oven when lit had a gas smell. It took three weeks to get someone out and was told it was the igniter and would cost 350.00 to fix. I then called dte gas for them come out as I have full house warranty. Since then five calls a new igniter and a new board just put in two weeks ago the board doesnt work. This unit has been discontinued. I would like to know why. And if there is a class action suit against. Whirlpool. Co.

The freezer has never been able to produce ice cubes, so, took the ice cube maker out, and bought plastic ice cube trays. Not what I paid for, but it’s cheaper than having to buy another fridge.

Let me start out by saying that I had a Whirlpool washer that lasted me for over 25 years and done a great job of washing my heavily soiled clothes. One day it refused to run and I tried to get parts for it but it had become obsolete and no parts were to be found for it, so I had to buy a new washer. I chose whirlpool again and let me say that it was a huge mistake. This model is a low water, high efficiency, top loading machine. It has nubs in the bottom that agitate to clean the clothes. The first time that I used the machine, I found that I had made a mistake purchasing this machine. It does not clean the clothes and there is NOTHING efficient about this machine. I have to run the washer twice to clean my clothes and they are still not clean. It leaves soap in the clothes and does not rinse them clean of the soap. What it does very well is extract water from the clothes during the spin cycle. This washer really turns up the high RPM`s on spin cycle. It has ripped apart several of my shirts during spin cycle. Whirlpool really failed badly on this machine. I see clearly now that Whirlpool is not the company that they used to be back in the 1980`s. I still have the whirlpool dryer that I bought back in the 1980`s and it still works very well. To end this story, I loaded up this NEW WASHER in the back of my truck and took it to the scrap yard and I asked them to destroy it in front of my eyes. I wished that I had recorded the destruction of this piece of JUNK and posted it on YouTube for the world to see. I got over $450.00 of pleasure watching the crane operator completely destroy this pile of crap. GREAT JOB WHIRLPOOL … YOU HAVE LOST A CUSTOMER FOREVER. I WILL NEVER BUY ANY OF YOUR PRODUCTS FOR THE REST OF MY LIFE and will advise others not to buy Whirlpool products as well. I am a male, 62 years old and work hard for my ill spent money on your JUNK. Life is always a trial, live and learn the hard way. Warning to all consumers. Do not buy Whirlpool products ever!!!! Whirlpool can K.M.A!!!!

I bought the Whirlpool WTW 5000DW1 washer and dryer to go with it. Within the first 2 weeks the plastic handle broke on the dryer. Ive been using the corner of the plastic handle ever since to open the dryer. The washer is the worst washer I have ever purchased in my life. The tub doesnt fill up over the clothes half the time. It is perfectly balanced on the floor but it always bounces around and you cannot open it to rearrange the clothes because they lock the lid. The only option is to try to hold it and wait for it to finish or start over by pressing the button for at least 3 seconds. I have had a few items get shredded by it and a lot of times the clothes dont get cleaned and rinsed properly. Even on 2 rinse option. Just the fact that it has a 2 rinse option is a big red flag. It is supposed to be a energy saver and water saver but that isnt true. If you have to wash and rinse the clothes twice because it has spots from the detergent still on the sheets, something just isnt right. Whirlpool shouldnt even put a product like this on the market. I have owned many Whirlpool products before this but this is the last Whirlpool product I will ever buy. Obviously Whirlpool doesnt test its products or care about quality.

I am very unhappy with the Whirlpool Cabrio washing machine that I purchased. Dark clothing comes out with lint deposits that will not come off. I have to rewash them at least one more time and then it does not always come out. I dont know if it is because the water level is too low or that it has no lint filter but I will never purchase another Whirlpool product again.

I could echo all of these complaints and more. I just gave up on the heater, junked it, and went to Home Depot and bought a Rheem. Recommendation: NEVER BUY A WHIRLPOOL!

I bought a 6 year warrantied Whirlpool hot water heater Model N50T61-403, product number 0733318, at Lowes Home Improvement Center and for three years the pilot light fails to stay lit. I have talked with Whirlpool 1-877-817-6750, the number on the unit, many times. I went through the troubleshooting checklist and verified all requirements. I paid a plumber $150 to check it out and he said I needed a larger supply line and venting the closet door would help. I did this and pilot still goes out periodically. Whirlpool sent me a new gas valve and it cost me another $150 to have it installed. The plumber said everything is good. But the pilot is still going out. Called Whirlpool again and talked with them for 24 minutes. The woman on the line was telling me I needed a certain amount of oxygen for this 40,000 BTU model. She was giving me minimum requirements for square or cubic feet of house with 8 inch ceilings. Yes, she said 8 inch ceilings 4 or 5 times as we went over the requirements. I got so frustrated asking her what she was talking about and she hung up on me. I called back and asked for a supervisor and a different woman had me hold on, came back and said a supervisor would call me. I did get a call back and the supervisor wanted to send me another gas valve and a burner assembly. I told him the burner assembly is working fine and I have a new gas valve. I asked him to send me a $150 along with it to pay the plumber. He said they only warranty the parts. So, am I supposed to have $450 in labor plus my time in this product on top of the original cost? I said no thank you and asked him if he would accept this as a solution if he were the customer and he said this is not a personal discussion. I know his answer. I am never buying a Whirlpool product again. But now I need to buy a new, good brand, water heater to replace the Whirlpool piece of junk. Bad product, bad company, bad warranty. I got screwed by Whirlpool once but never again.

I paid about $400 for this dishwasher and the regular price was over $600. Got a good deal. It washed dishes wonderfully. All I had to do was scrape the chunks off. It cleaned the rest. BUT... at a certain point, it started NOT cleaning. It was only about 6-7 months old. It was to the point where everything just came out kind of slimy and food grit was re-deposited on the dishes. I cleaned both filters. I made sure there was enough Rinse-Aid all the time. I ran hot water in the sink before starting to make sure the temp was hot enough. My husband went online and someone had instructions about cleaning the water intake because it could sometimes have sediment buildup. Not a difficult process, but there was no gunk in the intake filter. When I listened to a load it seemed like it drained, (most start with that), paused, rinsed for a couple minutes, paused, drained, paused and refilled for the wash cycle. So the pump worked, the arms went round and sprayed. Nothing was in the way of the arms. After it started the wash cycle, it seemed to just stall. It would spray for about a minute and then stop. Im not sure it sprayed after that. The timer kept counting down. It said dishes were clean, but it was an absolute waste of time. I was ready to go buy a cheap dishwasher and throw this one in the dumpster. I think it is a 720 padm??Just after my husband checked the water intake filter, we started another cycle. When it was rinsing, he opened it up and everything seemed to be working ok. It drained, then filled and started the washing cycle and then stopped. He opened it back up and surprise, the water was full on the front level by the float (that turns the water filling off). But in the back of the dishwasher, there was only about an 8th of an inch of water. Online it said the water should fill to just about the top of the heating element. It WASNT. Problem? It wasnt LEVEL. The instructions when installing said it should be leveled. We did when installing it (when it worked great). But looking back, we put in a new hardwood floor about the time it stopped working ok and we didnt put 2 and 2 together. We did not re-level. When we pushed the dishwasher back into its built in cabinet, it must have gotten OUT of level.The rinse part worked I guess. Then it drained and re-filled. After re-leveling the dishwasher, we opened the door at that point. The water was a level depth front to back and side to side. My husband explained what he thought had been the problem to me. When the wash cycle starts it fills, the float shuts off the water at the appropriate level. THEN... the dishwasher starts to pump and fill the arms and the tube up the back that feeds the upper washing arm. So much water goes into the arms and up that tube, the dishwasher looked almost empty of water again. As the dishwasher was now level, it began adding water to compensate for the arm/tube filling. Before the float would shut off too soon because the front part of the tub was full but the back wasnt. Without enough water, the dishes were NEVER going to/COULDNT get clean.The re-leveling made sure that the float didnt turn off the water filling until there was much more water, the CORRECT amount. The next load cycled all the way through, spraying much more than Id heard before and the dishes were clean. P.S. I also got some dishwasher cleaner and used that on a couple empty cycles. I NOW LOVE this dishwasher again. FYI If my husband wasnt handy Id have junked this thing. We HAD leveled the dishwasher when we installed it. Just didnt realize it COULD get un-level just pulling it in and out of the cabinet to install new floors. Check out all the troubleshooting stuff in the manual. But if it doesnt help, put a level inside across the bottom rack, front to back and side to side and make sure the bubble is in the middle of the two lines.The previous dishwasher I had, just made like a fountain of water that went up the middle of the dishwasher into a sort of funnel filling the upper arm. THIS one has that tube up the back and it curls down under the filter and Im guessing it is more sensitive to being OFF LEVEL, because the tube doesnt go straight down, it curls and lays across the bottom of the tub. Without being level, there was never enough water to suck up that tube to start the the actual wash cycle and it just stalled there till the timer said clean at the end. IE: dishes never did wash. BUT IT DOES NOW! Woohooooo!

I have bought a top load 6.2kg washing machine 3 months back. But now almost all the plastic parts are having a cracks. When I asked for replacement they said plastic parts are not covered in warranty.

I purchased this stove online and have been very happy with the features. I am able to use alternate settings based on the size of the Pan/pot. Cook timer, light, variable rack displays, etc. The only negative feedback is the need to add 5-10 minutes more to the temperature, based on the recommended cooking time of your recipe.

We purchased a new Whirlpool Refrigerator less than 3 years ago. The last couple of weeks the freezer hasnt been keeping cold enough. We lost about $300 worth of food in it. The refrigerator section isnt keeping as cold as it should. I call Whirlpool, but didnt have a warranty, so if I paid more money we could have a warranty and get it fixed. Who has that kind of money. When we purchased our appliances we thought we were buying good quality appliances. That sure isnt the case. They should last way longer than less than 3 years.I called where we purchased it from. Had the service man come out. There are four major parts that are wrong with it. $800 plus at least 3 hours of labor. Not worth that. Again who can afford such money as this. I called Whirlpool again. They could give me money off a new fridge but it would still cost almost $1600. Im so unhappy with the appliances. We also have a stove and that doesnt work right either. I believe that we should be compensated way more than they are offering. I would not buy another Whirlpool again. I will make sure people know that it isnt good quality. Im so sad. Who would have thought. It is time that the people at the top of the company think of those lower than they are. The people I spoke to on phone were very kind. I know they really cant do much. They are just the middle man so to speak.

On November 1, 2011, I purchased the Whirlpool Estate washer (model # ETW4400XQ) from Wholesale Appliance in Charleston, SC. The first time I used it I knew something wasnt right when both the regular and so-called gentle cycle agitated at an incredibly fast speed. It is damaging my clothes. I called the dealer and they sent out a service person. He said that was just the way it was and he couldnt do anything. So, I keep trying to use the gentle cycle, but it was the same thing. I would have to stand by the machine and stop it after a couple of minutes so it wouldnt ruin the clothes. The more I thought about it, I decided that the repairman wasnt right. I called Whirlpool customer service and they sent a different repair service. He also said that he couldnt do anything to make it slow down as it was programmed by a computer inside and he could not change it. I went to the dealer, Wholesale Appliances, and they said there was nothing they could do as far as giving me a refund or a discount on a better machine. The setting on the washer clearly says gentle cycle.” Well, the whole world knows that does not mean beat the clothes to death as fast as possible. Can you make any suggestions? Thanks.

I am sorry to have updated that review 2 years later. Whirlpool has actually contacted me after posting on their Facebook support group. I am not sure how it happened but I was contacted by their executive team who is WAY more professional and efficient than their support team. In a matter of days my washer was replaced and installed by a new one - the closet available to the model I had - I did not pay a penny and no questions asked even though the washer was out of warranty. So my answer to you is when you are stuck do your best to talk to the executive team!

My ref. stopped working. I troubleshoot it and did not work. I filled out a service request back on February 2nd, 2015. I got an email back from a subcontractor called Active Appliance INC. with a date service on February 6th, 2015, 4 days after my service request, and that is the only available date. The technician arrived while I am not at the house, however I talked to him before he started the work on my refrigerator and asked him kindly if he can call me after founding the issue, and he assured me that he will. No call and when I arrived home I found that he told the attendant that the refrigerator is not working and he has to report to the office. REALLY! We know that! Anyway I called Active Appliance and the customer services rep. told me that she could not answer with the diagnose until she speak with the technician and that will be Monday February 9th, I asked if I could speak with a manager, and her reply was Our managers do not talk to the customers. I had to hang up and call Whirlpool customer services and spoke with a nice gentleman, that he was not happy with Active Appliance INC. services. He placed me on hold and called them and within 3 minute he got back with the news, what was wrong with the refrigerator, electric computer panel burned out and then the fan continue to work with no stop, so it burned as well. He assured me that the services will be done no later than Tuesday February, 10th.While on the phone I got a call from active appliance and this time she wanted to know if I am warranted. I told her that I have Whirlpool on the other line and they assured me that I am. She said that it does not matter and she has to get something in writing. I placed her on hold and talked with Whirlpool and he assured me that he will contact them and email me a confirmation, which he did. By Tuesday February 10th, no call no follow up. I called Active appliance and they stated that it would take up to 14 working days for a part to arrive. I called Whirlpool and spoke with a customer services manager, and she got on the phone and told me that they are going to do their best and get back with me. Today February 16th I got a call to cancel a work service order due to technician calling sick and reschedule for February 25th Wednesday, I told her that they did not call to schedule the service first place, her answer was Never mind, I am calling to cancel anyway. Would you like to take this appointment or NOT? I asked her kindly to reevaluate their service procedures and the way they handle their customer, and I told her that I bought my refrigerator from Whirlpool and they are the company in charge of their product and I do not wish to continue this dialog with Active Appliance!I called Whirlpool and the customer service gentleman was helping me and we got disconnected, however when I called back they were closed for the day, however the customer service has my phone number but I got no phone call!!!! I think this is the worst POOR service I got within the last 20 years!!!!! I hope someone at Whirlpool care about their services and can contact me to handle the issue.

Have had this refrigerator for about four years and its broken down twice. It has rust and stains on the outside which are hard to remove. I have had other refrigerators that have lasted longer and were in better shape.

We have the Cabrio model and are thoroughly pleased with the performance. My only issue is the amount of sounds during the spin cycle. Otherwise, the machine is quiet. I like having the automatic dispensers for soap, bleach and fabric softener. Not having the classic tub makes loading a little different as the clothes need to be distributed around the side of the tub and avoid the center.

Purchased new 2013. The washer doesnt wash well and the spin cycle is malfunctioned - loud and the nut comes off and must be replaced often. The worst system ever purchased. DO NOT buy this washer!!!

This machine does not clean the clothes well, keeps an odor even after using Clorox (probably due to water inside that never leaves), and does not spin the clothes well. Every washing is longer than traditional washers and then I must use the spin-only cycle twice (adding another 30 minutes). I must also shake the inside of the tub to get the spin to work at all. The tech came out and re-calibrated, but to no advantage. Terrible machine and should be, as one viewer said, under recall, in my opinion. NOT WORTH THE MONEY -- and I am very disappointed in Whirlpool.

I purchased a Whirlpool washer in March 2007. That washer is now leaking from the bottom. I called Whirlpool. I was told that the machine only had a one-year warranty, so repairs would be at my expense. The CSR then offered to schedule a service call for me at $139, which I refused. A few weeks later, I received in the mail an offer for an extended warranty on my Whirlpool washer.

We have owned our refrigerator approximately 7 years. We have replaced this fan 3 times and now it went out again. The store we purchased it is now out of business. I am so flustered I do not know if we should replace it again or buy a new refrigerator, I can guarantee we will not be buying another Whirlpool. Their part runs about $50 but how do we know that is not going to go out again?

I love my Whirlpool LP Gas Range. Cooks great and bakes wonderful stuff. Also has a drawer under to hold pots and pans. Self Cleaning Oven. I do a lot of baking and I cook three meals a day. The burners are easy to clean off on top. I try and wipe spills up in the oven as much as possible, It has everything on it that I love, except it could have a plug in which would really nice.

I bought my Whirlpool 50-gallon gas water heater from Lowe’s 10 years ago. After the first year, it was nothing but problem. The thermocouple was replaced so many times and there’s the inconvenience of not having hot water. Customer service sucks and they continue to send you to Lowe’s to pick up the part for free. I have 2 more years on the warranty and Im replacing it after its over! 3 days ago my water heater stopped working and now again I will replace the thermocouple. Dont buy Whirlpool products: they are junk!

I just bought a Whirlpool Cabrio Washer WTW8800YC1 yesterday (1/19/14) delivered today. First load never finished, kept getting error of F51, which I looked up and its a sensor. I looked up the review on this washer and it seems to be the census that this washer is POS. Im having the store pick it up and refunding my money. My old washer is 20 years old and never had an issue with it. We just wanted a more efficient washer. Thank Goodness I didnt have the store haul it away.

The most horrible stove I’ve ever owned. The self cleaning oven never worked, the oven whistles while warming, the alert stops working after a few times, there is a razor sharp hidden vent under the dash of stove on which I cut my hand when cleaning. Customer service is nonexistent. Never never never buy Whirlpool.