My parents bought a Whirlpool refrigerator that makes a strange noise, an intermittent clicking. Sometimes it goes on for hours. It is neither the ice maker, nor the compressor. I contacted Whirlpool, they said it is normal. It is not normal. I have a twenty-year-old refrigerator far quieter than this brand new, $2600 noisemaker that keeps things cold.

I bought a Whirlpool refrigerator about 1 1/2 years ago. Mechanically it works fine, but many places on the outside are showing small rust, circular rust spots. Looks like the refrigerator has the measles. I dont think ordinary paint will cure the problem since it looks like the rust is coming through from the inside of the door. Any ideas as to what will cure the appearance and keep the rust hidden????

After 1 year and 5 months, my old side by side Whirlpool refrigerator stopped working. The melted ice caused floor damage and ceiling damage of the floor under.

We bought a Whirlpool French Door refrigerator in July of 2018 and it has gone out twice (quit cooling and has completely frozen over). The first time it went out at 6 months and the second was two days after the factory warranty expired (the warranty for the Whirlpool repair company lasted only 90 days for parts and labor which is useless). I’ve called the company to come take a look and it will cost over $100 just to have someone come out since we are outside the factory warranty window by four whole days. I was basically told there is nothing they will do even though the same problem keeps happening. This refrigerator was brand new and didn’t even make it six months.Now we will need to either pay hundreds of dollars for repairs (knowing that the issue will likely happen again) or buy a new refrigerator. Even though we have barely had this appliance a year. I will never, ever buy Whirlpool products ever again. I also posted my negative rev on their official website and it never got published. They only show their 4-5 star reviews (all of which say the customer has been incentivized in some way). This is a misleading and sneaky process.

The Whirlpool washer and dryer I bought new four years ago has been nothing but a giant on-going headache. No end to the error codes for washing machine. The dryer knobs broke off after two years. The washing machine works only when it feels like it, and important pieces that get a lot of wear are made of plastic. I will never buy Whirlpool again. Ever. Good luck to anyone that is brave enough to buy Whirlpool appliances. I have to say it again: Whirlpool is garbage, junk and unreliable.

Dont buy their produce!!! My refrigerators bought in January 2017 and just use 9 months. It breaks and repairs 3 months. It cannot repair and Whirlpool will refund for me, but I wait long time and no any answer. I try to call Whirlpool customer service. Their staff hold me long time and tell me they will be call back... Oh my God!!! I left my refrigerators 3 months ago. Whirlpool did not care the customer. Terrible company!!!

Cabrio washer - What a piece of junk! My washer is 2 years old, it now does its own thing - stopping when it wants, doesnt finish cycle, beeps finished and the clothes are so wet and the washer is not emptied. Then, I put it on drain and spin. One time, it kept going for almost an hour of off and on. My clothes were so out of shape and that was on low spin. I finally took them out and put them outside. The clothes from day one have always come out so wrinkled and that too is on low spin. Im afraid to use high spin. I know you have to for towels, but it still does not drain. It shuts off and on when it feels like it. My first contact with Whirlpool was, Well, did you buy the extended warranty? I hate it when asked that when purchasing any product. Its like saying, This is a piece of crap. Im warning you now so buy the extended. So right there, I felt Whirlpool isnt willing to help. What else can we all do here? Please advise.

I bought a Maytag front load washer on October 24, 2010. I have not been able to use it because it came damaged by the manufacturers. I contacted them by phone several times and it took them three months to send someone (A and E sears repair). Two months passed and I did not get the parts necessary or a replacement washer. I kept calling and finally they sent someone again in May 2011. They said they where going to order the parts because the new company was not going to replace the machine, even though it was already damaged. They said I would get the parts between three-five business days. I only got one part. A and E sent a repair guy again on the 22nd of June. This one said they needed the entire machine in parts and that he would order the parts. I called A and E one week later and they said they were waiting for the on manufacturer to send the parts (Whirlpool). The 26th and the 27th of July, I got the parts. On the 22nd of July, another repairman came and said we needed more parts. Today, August 16, 2011, I called Whirlpool and A and E and now they said the parts wont be here till after October 26, which by then I would have to pay for the parts and labor if I wanted it fixed because by then the one-year warranty would have expired. So here I am with a $700 washer, which was never used and they refused to fix/replace. They sold me a lemon!

I am very very unhappy with Whirlpool gold series. We paid more thinking it was better and dont waste your money. I have had the whole package for 3 yrs and every one has broken down. First my dishwasher wasnt cleaning. I had to take the thing apart and clean all bars and still is not cleaning right. My ice maker quit working and then started leaking under fridge. I had to have the water intake valve replaced. And now my oven says its at 350 and wont bake anything. I think the element has gone bad. This is complete junk. I should have known better and got LG.

A couple years ago we purchased a Whirlpool Cabrio WTW8000 top-load, high-capacity, washing machine based upon good claims of the salesman at Lowes - Appliance Dept. This was not an inexpensive machine. However, this washing machine failed to live up to representations and performance is poor. However, biggest complaint is that clothes are able to get stuck between drum and the unique agitating device which results in holes and tears in material. This is a significant design flaw and were not sure why more people dont complain about this rather significant design flaw. Of course, there are other shortcomings... but destruction of clothes is a serious problem. While this machine is in excellent condition, it will be replaced with a more traditional washing machine with vertical agitator ASAP.

Worse washer I ever had. Doesnt get the clothes clean. Called repairman. He said its designed to only fill machine so far so the country can save on water. Meanwhile Im washing the clothes twice, so what water is being saved? Government idiots!!! Can I get a new washer not unless I pay for it. Now just wasted money on a new washer and now my water bill is twice as much! Go figure!!!

Help? WP Gold double convection wall ovens WOD93EC0AS rated very high by Consumer Reports installed end of February. Monday April 6, fan in top convection oven came on suddenly while oven not on. When I tried setting a baking temperature in top oven to see what was going on, message read This function is not available. After about 15 minutes the fan went off, and I could use the oven. Worked well Tuesday and Wednesday. Oven not used again this week, but this evening, Friday, same thing happened again. Process has been repeated several times with fewer times between fan turn on. Have turned off power to ovens until I can get a repairman. Has anyone else had this experience or know what the problem is. Have been reading about the problems with WP ovens. Wondering if I need in addition to Home Depot Warranty the one from Whirlpool as well. Had Bosch convection ovens for 12 years then self-cleaned and thermostats went out and cannot be replaced because parts no longer made or available through any supplier. Said I would not buy Bosch ovens again because the parts became unavailable even sooner. What a mistake. Apparently self-cleaning element blows a lot of ovens thermostats and/or circuit boards. Loved the ovens and had only one repair after the ovens were one or two years old. The Bosch dishwasher is same age and still working great and usually cant even tell it is on.

Just purchased Whirlpool top load large capacity washing machine with no agitator at Lowe’s three months ago. I sit at the kitchen table in my freshly washed exercise clothes and smell body odor. There were six exercise items in the load and supposedly enough soap. The load washed for 45 minutes last evening. Yard work clothes washed yesterday are not clean. I had to remove grass from the bottom of the tub. When I iron my smocks for work, since I work with animals, I pick pet hair off of them as I iron. Judging from other reviews, this torture won’t last long, before I need to replace this piece of junk. My last washer lasted 20 years. If it didnt leak water, it would still be running. Thanks Whirlpool, I guess the joke is on me!

I needed a new washer and dryer, as I sold my other ones with my last house. I have been so happy with the economy of a front loading washer, and the clothes really dont require pretreating because Tide and the washer take care of everything!

I am very unhappy with the Whirlpool Cabrio washing machine that I purchased. Dark clothing comes out with lint deposits that will not come off. I have to rewash them at least one more time and then it does not always come out. I dont know if it is because the water level is too low or that it has no lint filter but I will never purchase another Whirlpool product again.

The Whirlpool washing machine came with our apartment. It is a top loader, which I like. The only difficulty is that no matter what I clean the interior with, I cannot seem to get it clean. It gets very dingy, even with HE detergents.

We got a french door Whirlpool refrigerator about 15 months ago. Model Wrf757sdem01. There were problems from day one. Serviced about 6 times by 3 different companies... Died again less than 2 weeks ago. Finally the store decided to replace it. Was under an extended warranty. We have been without a fridge for over 10 days. It has caused multiple problems for us as we are out in the country. We have to haul ice to 4 coolers... Wait on the new one (a Whirlpool). Plumber had to be called in and he has had 3 of this same model replaced! Years ago you could trust Whirlpool. Now apparently not. I hope we do not have to regret our replacement one which still is not installed! By the way the water filters have to be replaced to the tune of 100.00 a year. We are not going to use an icemaker or get water from the new one.

I purchased a Whirlpool oven/range from Lowes in September 2016. It was working ok until the convection fan stopped working. I purchased the extended warranty for 3 years but the oven stopped working in December (3 months past the extended warranty). When I contacted Whirlpool to complain about the horrible product they have been selling to people, all they could do was suggest a repair company that charges $99 to come out and diagnose the problem. DO NOT BUY any whirlpool appliances. The name brand used to signify quality but the appliances they sell now will not last. BTW I may have used the convection function maybe once per month over the past 3 years ... So its not like I over used the oven.

I bought Whirlpool top-loading high-efficiency low-water washer Sept 2018, model WTW5000DW, Serial # C83444466. Worst washing machine ever! No matter which water level you choose, it will not dispense enough water to cover the top of the clothes load, therefore the clothes are just moved from side to side with only the bottom layer of clothes getting wet; top clothes stay dry. Not enough water to fully agitate to clean the clothes!Whirlpool serviceman came today (Jan 13, 2020) to recalibrate the settings. VERY NICE MAN BUT THERE WAS NOTHING HE COULD DO TO SOLVE THE LOW WATER LEVEL. Recalibrating settings did nothing to solve the problem of not enough water. I am 81 years old and I have to manually add at least 4 buckets of water to an average load of clothes. This is unacceptable. Wont someone please initiate a class action lawsuit against Whirlpool for selling this very obvious poorly designed machine? NEVER EVER BUY A WHIRLPOOL WASHING MACHINE. It is a waste of money.

On August 16, 2016 I received delivery of an Whirlpool under counter refrigerator that I ordered online from Home Depot. Model # WUR50X24EM. Five months later, on January 10, 2017, it stopped working, I called Whirlpool for repair. They referred me to their service company, I called the service company the same day. They had a repairman out on the following Tuesday, 1/17/17. The repairman said that he will need to contact Whirlpool to order a part. Whirlpool sent him the wrong part. After numerous phone calls no one from Whirlpool could figure out the correct part number. The repairman kept sending over pictures and information on the correct part, but this all went nowhere with Whirlpool.On 2/7/17, I called and started yelling. I had been very patient up to this point. I was finally offered by Whirlpool a parts research to determine exactly which part was needed. Plus a $50 Visa card to appease me. At this point, its been four weeks without a refrigerator and no one from Whirlpool has put any effort towards trying to figure out the correct part. On 2/16/17, I called Whirlpool again to find out if they had found the correct part. They told me that the new part had been sent to the service company and Whirlpool scheduled me an appointment right then for Monday, 2/20/17.So today is 2/20/17, the repairman came and went, Whirlpool once again failed, they lied because the repairman came out with the wrong part that was originally sent to him when he ordered the part back on 1/17/17. I called Whirlpool and asked for a manager. They connected me with the Resolution Specialist. I told her everything and pointed out that it has been six weeks without a refrigerator. She said she will take care of it and get the right part ordered. I asked her how long I should have to wait, cause at this point I have waited long enough. She said she will have an answer by the end of this week. I dont believe her, I feel as though Whirlpool is pacifying me. I dont understand why they cant order the correct part.I have no faith in Whirlpool that they will do the right thing or have any understanding on how inconvenienced they have made me. I have no faith to the point that I ordered another refrigerator from a different manufacturer. It will be here tomorrow between 8am-12pm. Oh, and Home Depot, they washed their hands of this a long time ago. And, I have yet to see the $50 Visa Card.

This washer is a piece of junk!! It doesnt use enough water to clean the clothes and now it wont spin them dry. I have maybe two loads a week on a regular basis. I have always used HE detergent. Never overload. It is only three years old and I have been having to go to the laundromat because I cant afford a service call and especially if it is what they say which costs almost much as the washer. Be ahead to buy a used washer or a cheap one. It wasnt getting the clothes spun out dry enough - dripping wet. Then it flashed od and ul and sd and f51 and then it kidnapped my clothes - couldnt get the door to unlock with the pause or power until I unplugged and still had to wait several minutes. They refuse to help. Do not buy this machine!!! The customer service was not one bit of help. Instead she wanted to charge me $350.00+ dollars for some plan.

Whirlpool Dryer Model WED4815EWO and Whirlpool Washer W10682799 - I have always had great results with Whirlpool products. Both are energy efficient and save on operating costs. I purchased them three (3) months ago. The washer locks during the wash cycle. That took a little getting used to. I have always been able to rely on Whirlpool products. The top loading washer (W10682799) is energy efficient and high capacity. It regulates the water level so you dont have to worry about wasting water. The matching Dryer (WED4815EWO) has a sensor to regulate your drying time or it can be manually set. I appreciate the worry free, self-regulating functions on both the washer and the dryer.

I called customer service line regarding my Cabrio Automatic Washer (Model No: WTW6600SW2; Serial No: CU2171019) purchased on 11/24/07, to report and ask for assistance with a chronic ongoing service problem. Several calls in the past and service visits (at my cost) did not rectify the problem. Although there are many similar complaints on this machine regarding the loud noise and resulting problems during the spin cycle that involve the tub and rods, the representative said So sorry or Too bad we cannot not help you.My machine now does not run and is less than 4 years old --just like every other report. I get an error message F which the representative alluded to something involving the electronics. Machines purchased in 2004 from Whirlpool have across-the-board similar problems that Whirlpool refuses to take ownership for. This machine is their top of the line model. I dont feel the financial burden of repair or purchase of a new machine should be on the shoulders of the consumer. We bought in good faith from Whirlpool and expect Whirlpool to live up to their responsibilities. Thank you for any help you can provide.Rae **

I purchased my Whirlpool Cabrio H2Low from Sears 6 years ago. After numerous problems with clothes not getting clean (soap spots, stain transfers, etc) I learned the only setting I could use that actually cleaned was bulky with an extra rinse (so much for the energy efficiency). My first major repair was in the first year. Weve since had 3 more and the darn thing died again this morning. First the motherboard died and needed replacement, the drain pump failed, the door lock failed, and twice now it stopped spinning. At first I thought maybe I was just unlucky and bought a defective machine but repair sites are filled with reports of similar problems with these machines. I will never buy another Whirlpool product again.

Just got new side by side to replace old one. Motor runs every 30 minutes. Stays cold and makes ice but Im concerned about noise. Called Whirlpool and was told to record noise and show to Home Depot where it was purchased. No help from either place. Need to call warranty company. Funny thing it arrived with pieces of some sort of shrub in drawers. I guess this is new and improved and energy saving like newer washer that takes 45 minutes to wash a load.

I have had this refrigerator for 23 months. The ice maker has been a continual problem. It overfills and water runs onto my hardwood floor. After four service calls for the ice maker, the defroster heater caught on fire and melted the interior wall of the freezer. Not sure if we fixed the ice maker since we had the fire four days after the last service call. My service rep declared the refrigerator unrepairable. Fortunately I had purchased an extended warranty and they refunded 85% of the purchase price after 2 years of use. Besides the ice maker problem and the fire, I also had trouble with food freezing in the refrigerator compartment. I dont recommend this model, but my repairman says that Whirlpool is as good as it gets.

I bought all my kitchen appliances in Home Depot 4 months ago (April 2014). The wall oven, Whirlpool, never worked. Flamingo Appliances is the name of the company that does services for Whirlpool in my city. They keep changing parts and today is the 3rd visit that the technician will be in my house trying to solve the problem. Customer service in Michigan is DISGUSTING! I probably have to buy another oven because they say they wont replace it if they think its fixable. 3 MONTHS! I will never buy Whirlpool again. I hate them.

I had one of the first Maytag Neptunes. Loved it to pieces but finally had a problem and my beloved repair guy said it was almost 20 years old so to give up and move on. Obviously, cant be without a washer for very long so grabbed this Whirlpool Cabrio Platinum Washer. One of the biggest disappointments ever! Clothes come out streaked and splotched, dont smell very fresh or clean even straight after having been washed, stains dont come out even with pre-treating, have to run everything on heavy duty, whites are getting grayer by the week, and all-around horrid performance.Im ready to give up my Starbucks, start packing my lunches for a couple months, skip whatever treats I have to in order to get back to a quality machine that can actually WASH CLOTHES. I wondered exactly what it was or wasnt doing so I stood over it for half an hour. Initially, it loads up about a gallon of water and then spits it out over the rotating drum of clothes. Then it stops and spins that water out. I suspect the design logic was that it would force that gallon of water thru the clothes taking some dirt out with it. It repeats that stupid process several times. Then it finally gets a few inches of water in the bottom and the vestigial agitator tries to move it around.I watched one hand towel lie on top like a dead weasel, never getting pulled down or pushed out or whatever it was supposed to do to get down among the other items and squish together. Life throws me everything from sick kids spewing body fluids to people coming home reeking of hydraulic and other industrial fluids. When I say clean I mean CLEAN. This piece of junk couldnt satisfactorily process half a dozen dust rags. Neptune, Im coming back with my hat in my hand and a whole new appreciation!

All JUNK!! Replaced all new within the last two years. The washer I replaced was twenty + years and was still working fine was just upgrading, big mistake! Washer is sounding like it is going to walk out the door. Replaced dishwasher after twenty years and the new one was leaking within one year and recently got replaced. The new one did not last one year and also is leaking. Now washing dishes by hand. Lastly replaced hot water heater and that is junk too. Has six year warranty after one year pilot light wont stay lit, Whirlpool said would replace the gas control valve for free but I need to pay to install. I WILL NOT PURCHASE ANYMORE PRODUCTS FROM LOWES OR WHIRLPOOL AGAIN!!! HOW CAN A RETAIL COMPANY REPRESENT SO MUCH JUNK?

I have front loader, Ive left the door open after washes, run cleaning cycle once a month, never had any issues, like with anything. If you take care and service it regularly it will last a lifetime.

I have been without a washing machine for 3 weeks because my 4-month old washing machine does not work. I have had a repairman out 3 times and now one of the parts that he may need because unfortunately, its not an exact science is on back order. I have spoken twice to supervisors at Whirlpool and have gotten nowhere with them. They are trying to locate the part that is on backorder and my warranty is for repair and replacement parts only. By the time they get through with fixing this lemon, if it ever gets fixed, it will cost more than just replacing the machine! I have 5 people I am doing laundry for and a trip to the laundry mat every week is not something I can afford nor is taking time off of my job every week to meet with a repairman to try and guess what the machine is needing now. After 4 months, I should not have to even be concerned with what is and isnt covered by my warranty! My last washer/dryer lasted 12-15 years with very little ever going wrong with it. I will never recommend Whirlpool products or buy Whirlpool products again, not because something has gone wrong with the product, things like this happen, but because Whirlpool is very poor when it comes to customer satisfaction and treating their customers right. With this day and age of social networking and this economy, you would think that Whirlpool would do more to treat their customers right and build a product that lasts longer than 4 months. When I asked to talk to someone other than the supervisor I was given, I was told that she is the top person. Really? I find it hard to believe that there is no one above her that I could talk with to express my frustration and request that something be done about this problem.

Late on the evening of Monday, January 27, 2014, after springing a leak in my 8-year-old water heater, I purchased a new Whirlpool model N50T61 replacement from Lowes. Installation went smoothly and the unit lit off fine the first time. It heated the initial tank of water rather quickly, but the next morning, I noticed the status light on the control unit was not blinking, which indicated the pilot light had gone out. I relit the pilot light, the water heater fired off and appeared to be working properly. 12 hours later, the status light was out again. I relit the pilot, but within 20 minutes, it went out again.On Wednesday, the 29th, I called Whirlpool customer service and explained to the representative what had been happening. He stated that since the status light was not blinking a code, the problem was either an air supply or venting problem, and he couldnt help me. I relit the water heater again and performed the match smoke test described in the owners manual on the vent connection. It did exactly what the manual said it should do, so I assumed that was not the problem. However, while performing this test, the water heater went out again. This time, being right there when it shut off, I saw the status light blink twice about 5 or 6 times before it quit blinking all together. The two blink error code indicated low millivolt signal from thermopile.I called customer service again and explained to the representative what the first person had told me and also told him the results of my test and that this time, I had observed the two blink error code. He asked if I had a multimeter (which I do), so he had me disconnect the wires for the thermopile, connect the meter to the wires, light the pilot and read the voltage. My meter is an old analog unit, and not capable of reading millivolts (which is what the thermopile output is), and I informed the rep of this, but he had me do it anyway. As I suspected, I saw absolutely no reading on the meter. The service rep stated that he believed the error code and decided to send me a new thermopile assembly. However, their shipping department was closed for the day and I should not expect to see the new part until Friday. This was unacceptable, but he stated that this was the only option available to me.After thinking about this situation for a while, I again called Whirlpool customer service and told the representative that I was not satisfied with the solution previously presented to me and that I wanted a return authorization to take the water heater back to Lowes for replacement. The rep stated he couldnt do that, but said that there were a couple other things I could try. He attempted to explain these procedures to me, but wasnt able to do so clearly. He stated he would email the instructions to me. As of this writing, I still have not received the instructions.In the meantime, I did some internet research and found that Whirlpool water heaters have numerous chronic problems, including the issues I was experiencing. I decided this was not a product I cared to own. I called the Lowes store where I purchased the water heater and spoke with the manager. I explained the entire sequence of events to him, and he told me to bring the water heater back for a full refund. Since my local Lowes store only sells the Whirlpool brand, I took the money and purchased a different brand of water heater from another home improvement store. Needless to say, it will be a cold day in hell before I ever purchase another Whirlpool product.

I regret buying this washer. No complaint about the dryer but this washer has been the worst investment I have ever made. My clothes gets tangled up - seems like theyre not as clean as with my old washer which by the way I still have. I wanted a bigger set because I hated spending days off doing laundry but I spend as much time rewashing again and getting clothes untangled.

Do NOT buy the Whirlpool Cabrio washer...it doesnt actually wash your clothes! Most clothing still half dry after the wash (didnt get any water on them) and they are still smelling sweat after the wash! Also doesnt clean basic stains that others washers clean. Even if you add water manually to the washer to soak your clothes, the clothes on top wont be agitated at all, hence the reason the clothes are still dirty after a wash. Poorly engineered washer... its a lemon as it doesnt do what it is supposed to do (wash clothes). Biggest scam ever from Whirlpool and shouldnt be allowed to be sold to consumers anymore!

Our microwave is less than 8 months old, hardly used and only for heating items. Besides the point, being under a year old. It began to make noise and pop, spark sounds with the smell of burning wires and promptly stopped working. We called the customer service line and began the long frustrating circle of completely bizarre conversation. Maintaining our belief this is a fire hazard and not wanting it in our home they insist on a repair person coming after trying to sell us Extended warranty, Why would we want Extended warranty when the warranty is NO warranty, it seems, whatsoever. After requesting to speak to a supervisor 3 times. A overly bubbly person comes on the repeat same spiel and to make an appointment for 1 week away from 8am to 4pm to be available for a phone call to make an appointment to see about repair on said fire hazard microwave that is less than a year old. This appointment is made with repair place and they too are confused and noted Whirlpool said this is not covered under warranty, and they too would contact them.Today Whirlpool Canada calls and gives number to repair place to book appointment, Hello we already have one and the frustrating verbal dance continues. 5 minutes after this call the repair place calls, as whirlpool contacted them as well to book appointment, which we both could agree this is the bizarrest situation since we already have an appointment, from their appointment. We keep saying we feel unsafe, this is a fire hazard. Which they completely ignore. This is unacceptable and extremely poor service.

Approximately 2 years after purchasing a Whirlpool Gold Bottom Freezer refrigerator, I noticed cracks/openings on the interior walls on the ledge that holds the glass shelf! It is completely Crushing the styrofoam inside the refrig? Also, signs of being Cheaply made veggie bins are held in place by a piece of plastic that cracked after a few months. This was in 2011. First, I contacted the service contract people. They told me this was not covered under the policy. Next, I wrote & called the company. The walls show the styrofoam stuffing in the refrig. The shelves rest on these openings in the vinyl walls of the refrig box. This is a disaster and the refrig was 1400$$$. I have extended warranty which does not cover structure!!! What can one do with a New expensive refrigerator that has cracks in the Wall of the refrigeration box? Is there a class action suit anywhere that I can join?

We bought our new Whirlpool Cabrio Washer & Dryer combo from Lowes on the north side of San Antonio, TX, for delivery when our new home was completed in Blanco, TX. Delivery & setup went smoothly. But it wasnt long before we both noticed something wrong with the washer. What was supposed to be one of the quietest washers on the market was far from it! -- loud grinding & thumping noises when the spin cycle would kick in. Whirlpool service dept was called and a repair tech was dispatched - 4 TIMES! The tech from Appliance Science spends most of his time on his phone talking to tech support, and has pretty much changed out parts at will! The motherboard, the pump, the clutch, the splutch have all been changed, to no use!We still experience problems with the washer NOT spinning, or only spinning for a short time, and the clothes still soaking wet! Its a good thing the dryer works well, because the washer is a dud, and we cant do a damn thing about it! Weve been told by Whirlpool service that since we have a repair warranty, we cannot get a replacement washer because we dont have a replacement warranty. Ive never heard something so ridiculous! Color us highly dissatisfied in TX!

I purchased an over-the-oven microwave in November 2020 (Model # WMH31017HZ). It worked until March 2021 then began tripping breaker. The Safety department at Whirlpool stated that I have to get a dedicated circuit. After spending an enormous sum to get that dedicated circuit the microwave worked until April when just opening the door caused a spark that the electrician and I observed. By now I am sure that I purchased a defective unit but Whirlpool was not believing it. (As as aside, expect to stay on hold for at least 10-30 minutes when you call Whirlpool).May 7th the serviceman from Guincho ordered parts that was needed to repair the oven. As of May 30th the part still had not arrived. Finally, after multiple calls and excessive hold time, Whirlpool agreed to refund my purchase price and as of this writing on July 26, 2021 I have not received it. In the meantime I purchased another brand microwave and have to look at their defective one until they decide to pick it up. They have lost a customer.

Bought it less than 2 months ago. It doesnt wash. It doesnt spend. It works every 2-3 hours if Im lucky. Its the worst product ever. Its not like it was refurbished. It was brand new. Smh. I thought it would save me money by buying a washer. Off to the laundromat I go. I do not recommend this product especially to someone who has a family and on a budget.

Whirlpool claims this technology works to clean the oven; however after one month of use and one casserole spill, we attempted 3x to use this system and the cleaning process was a total failure. The gravy spill on the bottom and mild oil residue on the sides from roasted vegetables was the same as before the cleaning cycle was tried. The cleaning kit accessory from the company was a joke. It consisted of 2 sponges and a small scraper! We purchased the slide in model WEE745HOFS. Buyers of any and all Whirlpool products with Aqualift BEWARE... It does not work. We have since replaced the product with a range with the traditional cleaning process system that has worked for decades in most major brands.

Same as others, We purchased a Whirlpool Cabrio Washer and there is a bearing problem (which seems to be the common issue reported). The washer is unusable at less than 5 years of age. The repairman told us its a bearing problem and its common for this to happen to the Cabrio. How can an Whirlpool get away with selling a defective product?

In a recent decision regarding the highly expensive, supposed elite performing Whirlpool Gold refrigerators, a group of unsatisfied Whirlpool owners who are tired of cleaning water puddles from in front of their new refrigerators have hired all automobile corporations to manufacture cars only available to the CEO, Executive Board as well as the entire engineering staff at Whirlpool.These cars will be guaranteed to run ok. However, once the car is heated up under normal working conditions, the cars will be guaranteed to leak oil all over whatever surface they are parked upon. We hope that this will not be an inconvenience to the CEO of Whirlpool; however, perhaps once you have destroyed your new garage floor, you will understand the nature of our complaint with your poorly designed and engineered Whirlpool product.While this letter will have no effect on my current defective product provided to me by Whirlpool, it makes me feel better and I have not had the attention span to listen to my wife complain while she is cleaning up yet another (whirl) pool underneath our fridge.

This unit is without a doubt the best microwave I’ve owned. It is reliable, cooks to desired doneness. It defrosts and rewarms perfectly. For the price I do not believe that there is a better performer. Would highly recommend with no reservations.

I purchased a Whirlpool dishwasher and have had it repaired four times so far. Last time they replaced the main computer located in the door. I attempted to use the dishwasher tonight and it is completely dead once again. I usually have had good luck whirlpool appliances. After all these problems will no longer be using this brand. I contacted the store where I bought it from, Famous Tate. The first time it stopped working just a month after the manufacturers warranty ran out and they were absolutely no help. So in the future, I will no longer buy any type of Whirlpool appliances.

CABRIO GETS A ZERO RATING. We are sorry we ever bought this washer in 08. The unit had a defective main control board and was replaced in 2012. The factory authorized service agent from A&E literally robbed us of jewelry while in our home. Now the main electronic control board needs to be replaced again. Neither Whirlpool or their authorized agents are truly customer service oriented on the defective product. Neither are willing to make an honest attempt at regaining our trust. I have contacted both and neither will acknowledge or offer reconciliation. The problem with the main board and the recurrent F-50 error has been denied by Whirlpool although acknowledged in numerous consumer forums as this. Our family is now without a wash machine. We have not even received a simple apology for the theft from the service agency - even though their employee has been arrested. BEWARE!

Me and my wife bought a Whirlpool top load washer June 2011. Two months later the motor locked up and they repaired it; then the transmission started whining the next month. It was repaired. Now a bearing is going out all in the first seven months of ownership and they will not exchange washers, they just want to keep fixing this one until the warranty runs out. Whirlpool washers are a piece of junk and I will tell everybody not to buy anything Whirlpool.

We got the convection oven. It has no element like the one we had before with the fan. It is useless. We have to upgrade the temperature to get what we want. Difficult to clean. It does not cook like it should. We do not like it, period. Those electronic controls are not doing their work. No more Whirlpool appliances. Problems with the noise of our dishwasher also.

I bought a Whirlpool Cabrio 1.5 years ago and it has already died. Repairman need to replace the control board which had gone out. $450.00 to replace that piece, but could not guarantee that it would be the only problem. The motor or some other issue may have caused the board. This machine was purchased at Home Depot on sale and at $450.00 to repair would be approximately 70% of the original price. It will be cheaper to buy a new one rather than fix this one. We were not happy with this machine in the first place. It leaves the clothes stained with a white powder that never rinses off. The cycle time is very long, up to an hour to wash a load. The clothes are still very wet once the cycle is finished, which of course increases the drying time. I cannot recommend Whirlpool top loaders after my experience with this machine.

I bought a Whirlpool washer and drying matching set (model 6400sw3). I liked it because it was extra large without agitator in the middle. Ive had it for about 2-3 years and I have already replaced the drain pump, motor and barrens, it has cost me over 500.00. I thought now OK its working fine, but now its giving me a code every time I wash of LD. I am so fed up with this!! I should have bought a new washer but I felt as much as I put into it, I basically built a new one. And now this code comes up every time and I have to power it off. Im not sure if anyone else has had this problem but I just dont know what else could go wrong with this. I will never ever buy a piece of junk like this again!!

I would not recommend this product at all, nor would I recommend the Whirlpool Company. This washer was over $1200.00. Within two weeks of purchase, I had to call a service repair company as I was immediately having issues with the washer not draining. Being a front loader, this machine required using the appropriate HE detergent. I followed the instructions, used the appropriate products and had nothing but continuous problems. It is a (lemon), and very frustrating, as it does not seem repairable. No serviceman could give an appropriate reason as to why the washer would not drain, nor could they figure out why. It didnt matter the size of the laundry load or the type of items...towels, jeans, or silky delicates...the washer failed at turning from the wash cycle to the drain cycle. It also leaked because of the lack of draining, and began building up a mold film and odor even though I consistently wiped it dry and left the door opened when not in use. I received no assistance from Whirlpool and was given the runaround and told I must be doing something incorrectly.

I bought a Whirlpool High Efficiency top load washer. It does not get the clothes clean. Dark clothes come out with spots all over them. There is not enough water to rinse out the dirt. It is left on the clothes in spots. I have to take my clothes to the laundry mat to wash them to get them clean. I am 74 years old and have used Whirlpool appliances all my life. I have dt3 rental houses I keep Whirlpool appliances in. But I wont be buying any more. I had to call the repair man one month after I bought it. He had to recalibrate the machine. If all you want to wash or maybe rinse out is a pair of slacks or a shirt, it might be o.k. but not a load of dirty clothes. It is just a JOKE.

We purchased this machine a couple of years ago... What a disappointment! Was recommended to me by the sales person and I trusted her. The machine does not get our clothes clean!!! We are a couple in our 60s so our clothes dont really get dirty most of the time, but they come out with marks on them all the time. My dish clothes and wash clothes are a disgrace! Im continually trying to soak them to try and get them to look clean. Ive been going to write this review for a long time, but today was the final straw. Washed a small load of towels and had to rewash several pieces! I would never recommend a Whirlpool product after this experience.

My brother bought my 80-year-old mom this range so that she could bake all her delicious desserts with ease in a new beautiful oven. I was at her house visiting and saw that she was down on her hands and knees cleaning her SELF-CLEANING OVEN. She tried several times using the useless AQUALIFT FEATURE but to no avail. In this day and age with self-cleaning technology, WHY would Whirlpool install this unbelievable bad AQUALIFT cleaning feature? To see my poor mother scrubbing the inside of the oven like she did back in the 50s & 60s just completely appalling!! PLUS the top surface enamel is bubbling up with rust and the oven is only 2-3 years old. So we are trying to contact Best Buy to see if we can get a refund on this HORRIBLE appliance.

WARNING: Do not get the warranty plan through Whirlpool if you have stackable washer and dryer, you will have to remove the dryer yourself before they come out to service your appliances. I was willing to pay extra to have them take it down, the contractor said I had to call the extended plan service, yet 6 telephone numbers later to include the complaints department to no avail... Whirlpool contracts out so get your own and you may save a few dollars!

I purchased a french door refrigerator in March 2013. I purchased the Gold Series because I wanted the best. I have come to the conclusion that Whirlpool does not make a refrigerator with the quality to reflect the Gold Label or any label. My ice maker system created ice dams inside the fresh food area, in the ice bin compartment and allowed water to run into the fresh food area and floor. After four repair visits, I am still dealing with occasional water running down the inside of the ice maker door and into the fresh food area. I contacted Whirlpool and tried to get the defective refrigerator replaced; however, the very rude customer service representative insisted on another repair call by A&E. They scheduled the appointment for a time different than we agreed upon, so at this point I have had to cancel this appointment. I do not know why anyone would want to buy an appliance made by Whirlpool, which includes several other brands.

As described in many similar instances found on numerous complaint boards (including this one), Whirlpool has defective over the range microwave convection ovens (model # GMH6185XVS) with faulty magnatrons. I have had the exact same experience with a new product failing at 16 months (the first time) and within 6 months failing again. Whirlpool is not concerned about their consumers, only their money. They are more than happy to sell an extended warranty, but are not willing to work with customers that have lemon products.I tried working with Whirlpool customer support with little assistance other than to offer to sell me a $250 extended warranty. I additionally filed a complaint with the Better Business Bureau concerning Whirlpool to include over 10 pages in documentation with numerous people reporting this same complaint. Whirlpool is still not willing to acknowledge they have faulty or defective components in their product and so generously offered to pay for the replacement component (only - not the service to repair it).I spent $600 on this unit new, $163 to repair it the first time (at 16 months old) and no doubt it will cost me an additional $163 to repair it again (not even 6 months after the first repair). I am not willing to continue to throw good money after bad on a defective unit. For the cost of the repairs and their extended warranty, it is cheaper to buy a new unit from a different manufacturer.It is clear from this site (in addition to numerous others) that Whirlpool has a definite quality problem - both in products and service!

After only two and a half years, my Whirlpool bottom freezer refrigerator (GB2SHDXTQ0) was frosting over and the top food section stopped working altogether. I made a call to Lowe’s. It’s not their problem. I then called Whirlpool and he said I had a bad gasket. I had a 28-year-old refrigerator that was still working with the original gasket and it has no problem. After reading all the complaints with Whirlpool, I would never buy another one again. After cleaning out the refrigerator and freezer two times, carrying things to a friend’s house and having to pay $90 service calls just to walk into the door, I am ready to throw this one out. This refrigerator cost me $1200 and I am a single person living on $900 a month. Thanks for nothing, Whirlpool. There should be a class action suit.

Home owner bought a whirlpool water heater from Lowes. After the first year, the pilot started going out frequently. Tenants were left with no hot water repeatedly over weekends, etc. Changed numerous thermo-couplers, cleaned the screen below, but it continued to happen. I’ve paid plumbers for several service calls, which amounts the cost in excess of the price of the water heater.

This unit was new 11/11. Very little oven use but the 1st time the self clean feature was used the outer oven door shattered and now 5 years later there are no replacement parts available. Bought an extended warranty and no results from vendor other than refund $$ on what is left of warranty. Original cost $3200, now useless p.o.s. I will never buy a product manufactured by Whirlpool and hope they go out of business. Bitter... You damn right...

I purchased a front load washer and dryer brand new. The washer is under a 2-year warranty on all parts and labor. Since I have purchased them, the washer has had to be fixed on several occasions. I have had 10 parts replaced and had to be out a washer for a month at one given time. I have had the repair company email me all the parts and services that they have done. All I want is a new washer! I have argued with Georges Appliances on several occasions because I believe they sold me the obviously faulty washer and I dont believe that I should be responsible to have to figure it out for myself. They should be responsible to provide me a new one. They told me that I had to contact Whirlpool in order to receive a new washer. Please contact me asap.

I bought a Whirlpool refrigerator model #wrt1litzyv along with the extended warranty from Lowes. The compressor stopped working just before the warranty was to expire and had to be replaced. The cost of repairs almost equaled the price of the refrigerator and took nearly 2 months for the reimbursement check to arrive. I had to call several times. They told me they hadnt received the paperwork even though I sent it registered mail and it was signed for and I had to resend it. Now, less than 4 months later, the refrigerator is again not working properly. Freezer is not freezing properly. Takes 2 days to freeze ice. This is the absolutely worst refrigerator Ive ever had. My last refrigerator lasted 20 years. This one is only 3 years old and of course, the warranty is now expired. I will never buy another Whirlpool product. And I will never buy a major appliance from Lowes either since they play games with the warranties. And after the refrigerator was repaired, Whirlpool tried to sell me another extended warranty. They wanted $308.60 for a 3-year warranty. Ridiculous that they dont stand behind their products. And try to sell more warranties instead of just manufacturing a good product.

We purchased a Whirlpool hot water heater approximately 4-5 years ago and have had problems with the pilot staying lit. I contacted Whirlpool and their trouble shooting included doing a draft test (I am a teacher not a plumber) and removing the closet door that houses the unit. I am very frustrated by this entire ordeal and would like if they would replace the entire unit. At this point I dont want another Whirlpool product. The plumber made a service call at 12 noon and by 3:30 we had luke warm water and by 6:00 pm the water was ice cold! I will never recommend any Whirlpool products.

This is our second Whirlpool refrigerator that has the same defrost water drainage problem. I was told this newer model had updated technology, not so, actually it is worse. My older refrigerator went about 8 years before I started noticing water on the floor and this newer model is 4 years old and it started having water overflow at 3 1/2 years. Then in April we replaced the water filter and the ice-maker stopped working. My freezer also stinks like stale water (my reason for replacing the old refrigerator plus the water on the floor). I followed a YouTube video for defrosting the drainpipe, it was very tedious, labor intensive, and time consuming and worked for 3 weeks. This is very upsetting. After spending $2500 to have such problems and my expensive $150 4-year extended warranty expired just weeks before the ice-maker went out. This is obviously a design problem that Whirlpool refuses to address since my other model was a year 2000 model and my 2013 has the exact same problem. VERY POOR customer care in addressing these design failures of both the defrost drainage (just make a larger drain port!!!) and the ice-maker.

We have had a GX5fhdxvy 07 Whirlpool Gold French door fridge with bottom freezer that is approximately 4 years old. Since the first 6 months of use, so 3.5 years now, we have had continual problems with a flat sheet of ice on the bottom of the freezer which then builds up and leaks all over our floor. Twice I have slipped, once banged my big toe to the point of cracking my big toenail and bleeding profusely, and the second time I slipped on my butt and really hurt my back. This is of real concern as one of my children has Cerebral Palsy and autism and could really hurt himself in our kitchen. We originally called while it was still under warranty and the technician said that we will need to learn how to defrost the tube that seems to be getting built up with ice. Thats the only way to fix it. We thought it meant fix it for a long period of time. After several months of this re-occurring problem, we realized that this is something you need to do very frequently, meaning several times a week. We have had no help from Whirlpool, they tell us that essentially it is our problem. They didnt even offer to provide parts. They were not interested in our problems and just asked us if we wanted to pay for a service call, and that was it. Now but what kind of service is this?? Clearly, after researching these products, this is a design flaw and a lot of consumers have complained about the the same issues. You would think that Whirlpool would have the decency and the business smarts to create a recall to solve consumers issues.Unfortunately, I am not able to purchase a new unit. This was an expensive purchase as it was… and we have absolutely no resolution to the problem. I have to say that after our injuries in our household, eventually someone will slip and do some serious permanent damage to their body or even worse, fall and sustain a head injury and perhaps even die. And although this may seem like a far fetched comment, it really isnt out of the realm of possibility at all! How long does it take for a manufacturer to respond to a flaw in their design??

I bought a house with Whirlpool appliances and I bought the extended warranty for all the appliances, I started to have issues with the refrigerator almost 4 months ago and still waiting for results, do not buy whirlpool products, every time you call the warranty department be prepared to spend at least one hour waiting for a customer representative. Buy LG or GE instead. These are excellent brands that I have owned in the past.

Buyer beware. There was a class action lawsuit filed for our Whirlpool dishwasher some years ago. The control panel shorted and or overheated on ours in February of 2021, causing it to emit white plastic smelling smoke. (Glad we were home when we ran it.) I opened the door to turn it off and it continued to run, smoke and spray water all over the kitchen. Called Fire Department. Filed a complaint with Whirlpool. They sent a repair person to inspect and take photos. Its been 6 weeks and still have not received a call from them. I bought a Frigidaire. It is made by Electrolux. FYI, Kenmore is also made by Whirlpool.

We bought a Roper refrigerator about seven years ago. Less than two months later two of the cheap plastic door shelves broke and we had to buy replacements at over $20 a piece. Since then weve had to replace one more. Tonight another one broke so well have to fork over another $20+ to replace this one. I checked the Whirlpool website and they have the exact same flimsy plastic shelves as the Roper. I will be in the market to purchase at least three refrigerators in the next two years and you can bet that they wont be either Roper or Whirlpool. My advice to anyone in the market for a refrigerator to steer clear of these two brands as their shelving is cheap and shoddy.

We purchased the Cabrio washer and dryer set 2 years ago (7/22/15) from Lowes and have HATED them since day one. The first wash in the washing machine left clothes dirtier than when they went in. Our clothes have never gotten truly clean. The washer has a HUGE tub which is what I liked about it so I can wash my King sized comforters. What a joke that turned out to be. The comforters only get half wet even on the deep water setting. The machine even left dark stains on my light colored comforter and ruined it. Fast forward to 2 years later and the washing machine stops spinning and fills with water clear up to the top of the tub and wont drain. I had to put the machine on the rinse and spin option to get it to drain. Tried a different setting and it worked for a few months but started doing the same thing. The washer seems to be unbalanced no matter what size load I do. I am thoroughly disgusted with this machine and wish I would have never purchased from Whirlpool. The dryer has always worked fine until recently (2 years after purchase). It quit drying the clothes and leaves everything twisted up and wrinkled, even if I take them out of the washer and shake them out before I put them in the dryer. Doesnt matter what setting I put it on, the result is the same. So now it seems as though BOTH of my machines only lasted 2 years. Im not going to bother fixing them, these will be used as target practice. I will never buy another Whirlpool product again.

The Whirlpool hot water heater model ES80H123-45D from Lowe’s is a free replacement for a lifetime warranty unit that went bad after 8 years. First heater would heat to 154 degrees with a setting of 150. Very good. New one heats to 140 degrees with a setting 150 degrees. Digital ESM screen on heater reads 150, but the water is only 140 by my temperature test. I talked to complaint line 5 times in 7 days and was told to do various test, but the temp never went past 140. They replaced both thermostats and temperature still never past 140 with ESM reading 150. They first told me standard temperature was plus or minus 5 degree range. Then, they changed their minds and said it was 10 degrees. They are calibrating their equipment to operate 10 degrees less then their Energy Smart module reads to cover up a performance issue with their water heater. They say this unit will operate between 80 and 150 degrees—nothing’s said about a plus or minus operating range. I will buy a new temperature gauge to see if my old one is correct. It was tested against a digital one a couple of years ago when I had a new dishwasher installed by Lowes. The installers gauge read over 152 and mine read 154 degrees at the sink next to the new dishwasher, so it was close to accurate at that time. Whirlpool is happy with their under-performance.

I had purchase a Fusion Supreme refrigerator (model 180). After some time, I found that the color of the refrigerator was faded and I very well know the color of the refrigerator was recolored. This is a concern on your prestigious brand’s image.

Whirlpool N50T91-403 purchased in Mar 12 had an error code 4. I knew the water heater had a safety installed in it when I was working on the plumbing and allowed it to drain the hot water side down to 16% of capacitance of 50 GL. After the plumbing issue was resolved, I saw the water heater had shut off (thermal protection) but the switch wasnt tripped as far as I could tell. Knowing small processors can only remember anything if they have power, I removed the Honeywell circuit board and with my multimeter probed all of the capacitors contacting them both (-) and (+) and in reverse order. Doing this forces the IC to forget its codes because they require a small amount of voltage to remember them, usually powered by a small capacitor. I reinstalled it and voila! Presto! It works again.

Terrible! I bought the washer in December of 2010. We began finding holes in clothes in March of 2011. We found that we had a small crack in our dryer. After trying to fix it ourselves, the crack came back. So, we replaced the dryer. After we replaced the dryer, we began to find more holes in our clothes. It was not the dryer causing the holes, but our duet Whirlpool washer. We had several drain error instances as well. We have had the service repair man out several times for the drain error problem. Ranging from a Mardi Gras bead in the drain pump, to several baby socks to a large adult tube sock. Id say its been at least 7 times.We had finally had enough of our clothes, which I would estimate to be at least $500 worth of clothing, the service repair man said he had never seen anything like it. That was in November of 2011. They said they would replace the tub and drum system but it would take several weeks to get the part in, which took us past our warranty. After numerous complaints, Whirlpool offered the best they could do, that was to extend our warranty (6 additional months). The first drum was broken upon delivery, so another would have to be ordered. There goes another week. Finally it came in. We were all but assured the problem would be fixed.Two days later, same drain error code! 3 more socks caught in the drain pump! Took the socks out myself after watching them do it so I didnt have to call them out again and pay the fee. Next day, there were more holes in clothes! Called and and they said they cant get a service guy out for at least a week! That was all during the Christmas and New Years holidays! January 9th, the service repair man came and said, Yep, its the same problem. We need to replace the tub and drum again. The part would be guaranteed to be in by Friday, January 13th!Guess what? Today I got a call, the parts were on back-order and it wont be until January 24th until they can become available. Seriously? Seriously?! I have a family of 6. Me, my wife, a 8 year old girl, a 7 year old girl, a 5 year old boy and an 18 month old girl. The piles upon piles of laundry are limitless waiting for empty promises.In the meantime, we have had to wash essential clothes (school clothes, socks, underwear, etc.) at laundromats, and friends and other family members houses. Whirlpool doesnt give a care about any of our problems. I come from a huge family, as does my wife. Together, we probably have 100 family members. I will crusade against Whirlpool for any and all appliances if this matter is not fixed and their customer service is not better!

We purchased our Whirlpool Refrigerator #WRT519SZDB from the Home Depot 2 years and 10 Months ago. About three weeks ago it started to freeze items in the frig section. We lowered the frig section cooling level one selection and went on a two week vacation. When we came back, everything in the freezer section was thawed out. We had a tech look at it and he told us that the compressor was partly seized and overheating. Tried to reach someone at Whirlpool customer service by phone, email, and chat but so far, I have not had anyone contact Me back? Looks like repair will cost almost as much as a replacement refrigerator. So much for Whirlpool being a trusted brand!

I purchased a Whirlpool gas top range from Lowes in Somerset Ky September 2013. Model number WFG524SLAB1. The surface is showing bubbles. I contacted Whirlpool and they gave some kind of story. In other words I am stuck with it. Still under warranty but they wont send someone out to look at it. Lowes told us that it could be a paint defect when it was made. If the top starts peeling, it will be a real mess. I have never used anything abrasive on the stove top. As of right now I am not happy with Whirlpool at all and if they dont do something about this, I will never buy another one of their appliances.

My husband purchased a Cabrio washer and dryer pair for Christmas 2010. I have faithfully used the affresh every month, and spent a fortune on it I might add. But for about the last year or so, no matter that the washer has been cleaned at times when the load is finished there is all kinds of black stuff in the tub and on the clothes. The tray under the detergent dispenser is all black and nasty and impossible to clean thoroughly. The black stuff will come through the holes in the tub as well. Water stands in the bleach dispenser at times, fabric softener does not all dispense, the LID is broken and has been but I cannot afford over 200.00 for a LID and about 100.00 to have repairman to put it on. We do not have heavily soiled clothes that would create excessive dirt, never have had and we are now retired so we surely dont now. Bottom line, I thought maybe this would be the last washer I would need but I hate it. It is only 5 years old but I am stuck as I cannot afford a new one now. Factory rep says if it is cleaned as it should be, I should not be having this problem. Not true, it has been cleaned as recommended!!!

I purchased new and installed my heater in 2003. SN: 0253109845, MN: EE3J50RD0454. I started removing and replacing or cleaning heating elements in 2011: pretty good service. In 2015 I noticed black and brown water coming from the hot water taps. I opened it again, cleaned it, and realized anode replacement was required. That is when trouble started.I tried everything usual including 4 foot cheater bar, heating the coupling, impact wrench, tapping with a hammer, etc. Finally found a 700 ft-lb. pneumatic impact wrench on sale at Harbor Freight. After serious wear and tear on my air compressor and about 1-1/2 hours of work with the impact wrench, I got it out. The threads were messed up some, but I did not look close. I had to put the 1-1/4 inch head back in to return it to service while I found and ordered an anode. Could not get one from Whirlpool and could not buy one in Lowes where I bought the heater.The surprise was when I cleaned the threads to put the head back in, I had to use almost as much time and torque to get it to stop leaking as I did when I took it out. Then, when I did try to install the new anode, it required to same effort. Conclusion, There was some kind of imperfection with the threads in the coupling that messed up the threads on the initial installation of the anode, which made it nearly impossible to remove. Whirlpools quality control stinks. The next one will NOT be Whirlpool.

We bought our Whirlpool Cabrio 7 years ago and it was great at first. I have not had any trouble with it ripping clothing. The clothes are clean. Its constantly breaking down. First it was the drain pump. Then the main computer board went! I called Whirlpool and of course the lady says its not covered. I had back up though. Google is amazing! I asked why this wasnt a recall as all over the web, people had this same problem. I pushed and pushed and she put me on hold. Came back to say it was in fact covered. What? Really? What changed your mind? She wasnt allowed to tell me. Supposedly had something to do with the date of manufacture. So okay, they send the repair guy out, its fixed. Now tonight, the lid locks and nothing happens! This repair was about 6 months ago. Grrrrr. Its been one thing after another with this hunk of expensive junk. When I buy an appliance I expect it to be problem free for far longer than this. I am not getting a code or anything, just dead air. So frustrating with three kids not being able to do laundry when I need it randomly :( Has anyone else had this problem? The lid locks, then does nothing. I unplugged it, pressed off and restarted it. Changed settings. Nothing is working.

Cabrio washer and dryer are not energy saver by any means! Have had the pair for almost 1 year and have spent at least 3 years of washing and drying time with these. What use to take 30 minutes to wash now takes at least 48 or more and the dryer has to be run twice on lots of loads to dry! The other thing is, with no water in the tub it really does not have a soak cycle to get really dirty stuff clean, so you wash things 2 or 3 times! Now I know why I see these washers and dryers like new in the used stores for $200 to $300. Thanks for the junk Whirlpool.

This is a replacement of a similar model, that lasted 23 years. This modest, white, 2 door, side by side refrigerator, was purchased without the optional ice maker. It was bought specifically for the dimensions, of our custom cabinets. There are obvious differences, from the previous incarnation. The textured doors were replaced with a smooth glossy finish and their height extends higher than the refrigerator cabinet. The adjustable shelves were replaced with less adjustable pre fixed shelf supports. The LED interior lighting is much brighter that the incandescent bulbs they replaced. Overall, so far a very capable refrigerator, for a moderately sized kitchen and if the life, lasts as long as the one it replaced, this was a very good purchase.

I bought a Whirlpool 3.4 Cu Ft. Top Load Washer, Model: WTW4800XQ on Sunday. Today is Tuesday morning, but the machine broke last night. It lasted for about 5 loads and they were not big loads, unbalanced, and yes I had the right amount of soap. Whirlpool is saying that I washed something that was not machine washable. However, that is simply not true. I washed the bathroom rugs (which have been washed many times before) and they are saying the pump is clogged. If I had a washing machine 48 hours ago, do I really have to pay a service repairman to fix it? I will never buy any Whirlpool product again.

My review merely echoes the other 1-star reviews Ive read below, but Im including it anyway. We bought the Whirlpool Cabrio from Lowes in 2013. Two weeks ago, a mere five years after purchase and shortly after our warranty expired, it broke. It kept showing the UL code and took multiple cycles to wash the clothes. Unacceptable. We called the technician; he came out; told us it was the bearing that busted; and quoted us $800 to fix it (I noticed below another customer was quoted $400 for the same issue). We told the technician thanks but no thanks and purchased a $450 Samsung washer. Our family will never purchase any Whirlpool product again. From their customer service to the performance of their machines-- its all very much lacking.

Purchased on 7/9/18, was alerted of gas leak on 11/24/18, gas company had shut off gas to the unit. After finally getting through to their customer service in December, they scheduled an inspection with a local repair company they contract. It is now January 15, 2019 and I still have not had any resolve to this. Whirlpool is washing their hands of any responsibility, and doing nothing to help find a solution for a defective burned out piece in their oven, which the repair tech said he’s only seen in units over 10 years old. I do not feel confident or safe about this range. I bought this new from Best Buy, 4.5 months of having this in my home, after 1 oven use this happens.

Whirlpool Cabrio WTW8500DW0. Like: Top loading, Handsome appearance, clear glass lid, easy access soap dispenser plus separate Oxi dispenser. Dislike: Does not have a soak cycle. We didnt realize until after we replaced our old Sears Calypso what a really poor job it was doing. It damaged the clothes and never really got them clean. Also, the small capacity made it nearly impossible to wash large items such as bedspreads or comforters. The Whirlpool Cabrio WTW8500 has be a delight.

We bought a Whirlpool refrigerator, model ED5LVAXWSOO. Although we didnt need or want the ice/cold water dispenser, we bought the model anyway. We have never hooked up nor used the ice maker/water dispenser. As the refrigerator was powering up upon its initial start-up after delivery, we found that condensation was leaking from the ice maker on the door. Upon closer inspection, we found that the hatch cover was not sealed and actually jiggled around when the door was opened or closed. A service man came, had difficulty with the issue, but eventually said he fixed it. It didnt leak again for almost three years. Then the exact same problem. (Remember, the component is still neither hooked up nor used.) Apparently, the opening and closing of the doors eventually caused the same defect to reappear. Of course, since the warranty has expired, Whirlpool sees no obligation on their part. But the value of a product is not based on a limited-time warranty, but on how the product holds up. This has to be a manufacturing or design defect as it came from the factory broken, and eventually the same problem re-appeared even though there was no wear and tear on the component, as it is not used. These products are much too expensive to begin failing after a few years. I would caution buyers based on the product being delivered broken (wheres their quality control?), its lack of durability even when not being used, and the Companys disavowal of any responsibility beyond the limited warranty period, even though it is a recurrence of the original problem (which to me means that it wasnt properly repaired/corrected during the service visit). Whirlpool eagerly grabbed our hard-earned money, but delivered an inferior product made worse, in turn, by its sub-standard service and lack of accountability.

I got my water heater 3/13/12. Ive had to restart it now 4 times & have been totally out of hot water for two months! How can I get help from you or Lowes? This thing is supposed to work for 6 years & I havent been able to keep it going for 6 months! Help please! Can I get a different one? This one hates me! Being widowed & having a metal hip, it’s hard to get safely into the attic to restart it and not sure it will work longer than 2 or 3 weeks! Ive been bathing in the kitchen because thats where the stove is! Thats the only way I have of having hot water, is on the stove! Thanks for listening!

Bought a New Whirlpool washer. Was ok at first then began to have problems. Called a repairman. Only to find out it was made in Mexico and was a piece of junk!! So in order to fix it the cost was 300 dollars. Then I was told that all the new washers were not so good. My heart broke. If you need a washer youre in for a problem. Look to see where they are made. Theres more new washers in the junkyard than ever. Buyer beware.

I purchased a Whirlpool Cabrio Washer WTW6200 & this yr purchased a newer dryer w/ steam capability. I wish I would have waited a couple months for a new washer that yr and purchased the one with no agitator inside! But my washer died that day & I needed one & NO ONE informed us of the changes or problems of this agitator at the time of purchase. I have had this service several times my first year and the agitator replaced I believe twice. But it still destroys clothing. I called 1 month out of warranty and even though they had been out several times the first year for the same issue, they would not help me! Yep, even after the 1st year they said to get things done I had to purchase an extended warranty even though this was a mfr issue no doubt! So, 3-4 years later I still am dealing with the very same issue over and over with NO RESOLUTION in site and $900 in the hole for this washer and I am losing money with clothing damage weekly!Even today I had two pair of jeans, $98 ea rec these terrible uniformed marks all across the legs making them unwearable! At least for where they were intended to wear them at. They are now yard jeans...yep $98 expensive yard jeans now!!! These were my good jeans which I cant afford to buy more nor replace them so I have to do without. We cant wash anything with strings such as hoodies, shirts or baby clothing with spaghetti straps or little dangle things; we have to use the laundry mat and come home & dry w/ my Cabrio steam dryer which I love. Most everything I have to use zipper net bags but even then things still can get destroyed, especially if a hole gets torn in the bag from the wings of the agitator as you will see in the below photograph. I currently have & own an expensive washer I purchased from HHGregg by Whirlpool replacing a previous whirlpool I owned for 22 years! Yep, Im wishing I had it back & put the $200 some needed to repair it! Please Whirlpool will you please do something & make this right once and for all. I dont have $900 for another washer. I just want to be able to use my washer without it destroying everything I own. I have darn photos of what this is doing and you wouldnt believe it. It took us an hour, yes an hour to untangle a top that became entangled in the flaps on the agitator. This is the worst design I have ever seen and needs to be recalled once and for all and either fixed or replaced with new machines of equal model with the agitation issues resolved or removed & with no issues or further costs to your customers! Why would you honestly believe that an agitator with wings coming off the bottom that are not attached to the bottom would serve some type of positive purpose in cleaning clothing? All it is doing is tearing them to shreds, tangling them up, doing things to hoodies which make them unrecognizable after ripping the cords so hard out of the hoodies that Ive seen them shred the material across the collar area and opening of the cording completely ruining hoodies ranging from $35-$75 a piece even after placing them in mesh bags! Why did we keep placing hoodies in the machine? Well with 4 children at times they just dont listen or get all the info as to what is going on with the machine as 3 were college kids coming home periodically & yes, to do their laundry. Look, lets talk straight. You as a company from what I have learned from appliance salesmen locally and regionally, you knew this was wrong and knew this was your last ditch effort of an agitator before you knowingly knew you were going to an agitator-less unit on your washing machines & already had one ready to go out on the floors. I know that you Whirlpool CEOs knew this unit was a bad call but chose to ignore it. You had to know it because there was no way this could have passed quality control. It had to have failed sometime in its trials showing you the issues of the wings. Unless you never did any quality control on this unit and just rushed it through? Please to the CEOs of Whirlpool, I am asking you to make this right if not for good standing of your company do it at least for families like myself who cant afford to buy another machine and are now stuck with NEW machines yet going to Laundry mats. This was to be my last washing machine I would buy hopefully. I am 54 and was not planning on buying another. How do you think this makes your company look???? Im just so tired of dealing w/ Whirlpool to only hear I have to purchase a $400 extended warranty with no guarantee that they will fix the issue. If an attorney wants to step in & believes they can help us and maybe others then Yes please help us because this is absolutely ridiculous and is a product that needs to be recalled. We are out so much money now and like I said we are to the point we cant purchase another washer. We had to purchase all new appliances as they all began going bad around the same time.

I have a Whirlpool refrigerator and it is the 2nd one in 12 months. The first one the refrigerator was freezing food in the fridge part and thawing food in the freezer part. After several times a technician came to try to fix the problem and arguments with Whirlpool. They finally replaced the refrigerator. The new one is now doing the same thing. I am contacting Whirlpool tomorrow.

The top of the range stays very hot. Not the burners -- just the top of the stove itself. Now the oven pilot wont light and there doesnt seem to be any sound or smell of gas when I try, though the range works fine.

I first want to begin by saying that we have been a Whirlpool family for years. I now own a Whirlpool microwave, hot water heater, washer/dryer, Jenn-Air stove and dishwasher. My problem now is with the Cabrio Washer purchased in 2008. I started having problems in 2011 and the same problem has raised its ugly head again. When I try to use the Clean cycle, it starts at a 60-minute cycle and goes down to a 2-minute cycle in 3 minutes without cleaning or even running water into the tub. This time, it made a terrible noise and stopped. The tub was replaced in July 2011 after having the same complaint as above. The repairman said that the mechanism on the tub to fit into the spinning cycle is made of plastic and is not holding up. Also, in March 2012, a new control board was installed. I spoke to Whirlpool Customer Service and they informed me that they did not have any other complaints about the Clean cycle and that I should call the repairman. Luckily, I purchased an extended warranty. I vote a thumbs down on the Cabrio washer.

On November 1, 2011, I purchased the Whirlpool Estate washer (model # ETW4400XQ) from Wholesale Appliance in Charleston, SC. The first time I used it I knew something wasnt right when both the regular and so-called gentle cycle agitated at an incredibly fast speed. It is damaging my clothes. I called the dealer and they sent out a service person. He said that was just the way it was and he couldnt do anything. So, I keep trying to use the gentle cycle, but it was the same thing. I would have to stand by the machine and stop it after a couple of minutes so it wouldnt ruin the clothes. The more I thought about it, I decided that the repairman wasnt right. I called Whirlpool customer service and they sent a different repair service. He also said that he couldnt do anything to make it slow down as it was programmed by a computer inside and he could not change it. I went to the dealer, Wholesale Appliances, and they said there was nothing they could do as far as giving me a refund or a discount on a better machine. The setting on the washer clearly says gentle cycle.” Well, the whole world knows that does not mean beat the clothes to death as fast as possible. Can you make any suggestions? Thanks.

Just bought what I thought was going to be a great dishwasher. It had all the features I wanted. But, I discovered that none of my silverware would fit in the slots provided in the silverware basket. It is a disaster. The slots are so tiny that most of them are unusable. I called Whirlpool thinking that surely there was another basket I could substitute, but no, there isnt. Everyone was very polite, but the end result is that the Ill be handwashing most of our silverware. Unless your silverware has very narrow handles, forget this machine. Obviously designed by someone who has never loaded a dishwasher!

I recently purchased a Whirlpool Slide in Oven replacing my Amana stove of 15 years. My Amana was a very basic model, and I thought this WP was an upgrade. But it is so poorly made its ridiculous. First of all the bottom storage drawer, is so flimsy, it does not slide out easily, and the top lip doesnt even have a finished edge. Additionally there is a 1 inch gap between the top of the drawer and the bottom of the stove door. But the BIGGEST disappointment was the oven racks, totally flimsy.We used a Lodge Dutch Oven (which we have used many times with our old stove) and the oven rack sagged under the weight. Had I known I would have pulled the racks from my old stove. I contacted that seller about these issues, and they said they are ALL like that even the higher end ones, and I contacted Whirlpool to see if I could buy better quality racks and they said no, this is all they have.

Within 10 days of installing our new Electric range the cooktop does not look new and although we have used the prescribed cleaning methods, will not remove some cooked on spills over one burner and another burner has white rings around the glass above the dual zone cooking element. While we did not choose the top-of-line model; had expected much greater durability and appearance for our new range. My call into Whirlpool service made me feel like mine was an extremely isolated case and yet nothing would be covered as would be classified as customer fault. Highly disappointing as the cooktop on the range that we replaced seemed so much more durable.

On the 10-05-05, I purchased a Whirlpool natural gas water heater from Lows Orem. The unit has a 9 years warranty agreement. Lows sales S0178JC3 647605; cost $378. Model number FG1H5040T3. Serial number 0515140765. Following installation, the unit has failed repeatedly. Since keeping records of the failures, the unit failed either by the gas control valve or the thermocouple on December 2011, November 2011, April 2010, February 2009, and April 2008. Whirlpool has at all times supplied the parts but denied that the parts are technically faulted. Whirlpool has further rejected all requests to refund me for defective product. The major consequences have been an unreliable water heater. There were periods without hot water. Time was spent involving undertaking repairs.

We bought our washer (Whirlpool Cabrio) from a rent to own company about 2 years ago, and finally got it paid off. About a week ago, the lid started sticking when it was done washing. I went to open it last night to start some laundry, and it BROKE. Now theres a piece stuck in the bottom part of the lock, and the washer wont start. Anyone else have this issue?

Whirlpool Gas Water heater purchased from Lowes in 2012. Have replaced two thermal couples and three gas control valves. Will not stay lit! Problems began within six months of purchase. Third gas control valve quit functioning today and Im on my way to Home Depot to purchase a Rheem...Im done with Whirlpool!

We purchased a Whirlpool conquest from Lowes in 2009 and purchased a Lowes warranty. About 2 years ago we started seeing hairline cracks on most of the drawers and shelves. I complained about it last year and a lady from the Facebook page did offer 50% off new ones. Since then we have not been able to afford to get any, and today we lost our last shelf. If I wouldnt have checked it, it would have broke along with anything on the shelf. I have never seen such horrible parts. We have another small very old fridge that has help up better than this. At this point I will never buy another Whirlpool.

The washer began to start making noises as if coins were in it or plastic breaking every time I wash. Also, it does not wring clothes out good and clean well. I have Whirlpool Cabrio.

I had problems with the door closure on day 3 of my French Door Refrigerator Model # WRF560SEY. The flap on the left door that seals them fails to fold back if I open the right door first. Which didnt seem like a big deal until I tried to close them and have to remember to close the left door first or itll bang against the right door and Im afraid itll break that piece off then the refrigerator is worthless. The manufacturer drop shipped a new piece, after several attempts of adjusting the closure, and it still does not work. I have written Whirlpool and am told they have a new door on order but it will take 6-8 weeks, that was in March. Now when I contact Whirlpool no one ever returns my calls or emails. I have had the refrigerator only for 15 months and I have fought with either the store or Whirlpool since the third day of owning it. No one cares as long as the appliance is paid for. I will never buy another Whirlpool appliance.