We bought our stainless and black Whirlpool stove last month. We love that its black topped, and doesnt show dirt. We love how the oven door seals, and the fast heat. What we do NOT love, is how easily the knobs turn. You barely brush against them, and gas leaking into the kitchen. I called for service. Our guy said yes, they turn easier than most of the stoves he has worked on. He called tech support from my kitchen, and I overheard the guy at the other end. His response was dismissive. I have had gas ovens for 20 years. They have without exception, had a spring type feeling to the knob. This stove has none. I am writing this so that if others are experiencing the same thing, they will see it is not their imagination. Something is wrong with the design of the knobs or some part is missing.

It has performed perfectly for the past eight or nine years. Only problem has been little plastic parts broke that held one big drawer that we may have overloaded. Door shelf plastic part holding it on... broke also.

Got the dreaded 4 flashes LED status - High Temperature Shutdown. Online and vendor documentation says that this condition requires gas valve unit replacement, a $115 option. If your Pilot remains burning, but main burner does not kick in, then a good guess is the circuit board requires a reset. Prior to any further work, test the Thermopile, that is the round item with two blades located below and to the right of the gas valve unit. Move knob on control panel to OFF1) Pull out plug with red and white wires located on front of gas control. 2) Have someone Hold in the control knob on the unit at Pilot, and make sure Pilot flame is burning. 3) Using a multi-meter, set it to millivolt reading, and test voltage across the two wires. Voltage should be greater than 350mV, preferably >500mV. 4) If you get a reading in that range, your Thermopile is good. Turn knob to off position. Do NOT uncouple gas lines. 5) Piezo Igniter wire comes apart, disconnect it. 6) Remove screw that holds front cover. (screw located bottom left as you look at the unit) 7)Cover simply pulls off directly towards you. 8)Remove the screw holding the circuit board to the cover, and remove circuit board by unclipping it - 3 clips, one either side and one at bottom. 9) Unplug the 3 strand thermostat cable, you should now have the circuit board clear. 10) Take a piece of aluminum foil, fold it twice, then lay circuit board on it facing up, do it on top of tank, want it grounded. 11)Using one of the multimeter probes, wrap a piece of foil around it, keeping point free, and ground it too. Then slowly work around the board, touching all the solder connections you see, as well as the chip legs. Pay particular attention to the round objects on the board (capacitors), make sure to ground out each of the solder points, visible either side. (takes about 5- 8 minutes, take your time) 12) Once done, reconnect thermostat cable to board, then reinstall board into cover (dont forget the screw)13) Place cover back into place, screw in cover screw, reattach Piezo wire and black electrical plug with thermopile wires. 14) set Knob to Pilot, get pilot lit (may take a few hits on the Piezo button) and while still holding the knob in, watch to see what LED flashes you get (there will be a 10 second time lapse before it will start to flash) 15) You should either get 1 flash or 7 flashes, that means the board is reset, now turn knob to warm, and see if main burner kicks in. Good luck, and for a half hours work you have saved yourself $$$. PS: If it occurs again, you have sediment build up, need to drain the tank.

Im so tired of the mold smell that never goes away, even after following their cleaning cycle many times over. I dont know what to do but I spent extra $ to purchase my washer and now this!

We purchased a Whirlpool dryer about two years ago. Unfortunately I havent had the time to compose a letter stating my dis-satisfaction until now. After much research and haggling we decided on the Whirlpool Cabrio Platinum model, a very efficient (we thought), and even attractive model. It has proven to cost us much more than we bargained for, as EVERY time I do a dark wash, which is usually two to three times a week I must re-wash the items once or twice after! All of the items come out of the wash with white spots all over. Thinking it is soap, I run the wash again on a rinse cycle: nothing changes. Then I redo the wash - this time not using soap. The result is a bit better, but I still have to take a wet washcloth and rub the areas out.I did voice a complaint one time to which I received a letter stating that I should read my manual, specifically the troubleshooting guide. I dont have time for this. Again, we purchased this machine for its cost and efficiency, yet its ending up costing much more than it should as for every load I do (of dark clothes), I have to do one or two additional. (No telling what is on the light or white clothes that I cannot see because of their color!) This machine has been a total waste of time and money; I will never purchase another Whirlpool machine as I am extremely dissatisfied with this product.

Both are Whirlpool Commercial quality. I got them free from my Co-Op. They didnt cost me anything. They have been here for years - at least 18 years. They have performed flawlessly. I would look for anything discounted. I do not have a problem buying scratch and dent items or last years models. I am not big into brand names and their claims. My sister has gone thru several Maytag appliances in just a few short years. I will not buy any front loading washer, its top load only for me. The dryer has to be electric because we do not have gas in my Co-Op complex. I have been lucky to have only two washer and dryer combos since I was a kid. My family bought a Kenmore washer dryer combo in the 70s that lasted maintenance free into the 90s when I got the Whirlpool set that I have now. I only need the basics side by side set ups. Even though I live alone I do a lot of laundry. Since I have had these commercial grade machines I am more leaning toward another set of commercial grade machines. They seem to be able to take more abuse/over loading than the fancy expensive machines.

I agree with all the other reviews listed here! How in the world is a washer to get clothes clean when there is no agitation? Or enough water to even cover the clothes? This is a complete waste of time, one cycle can take an hour or more, because the extra rinse cycle is necessary. And it takes 20 minutes to just sense the load. What a crock. And yes my clothes smell also. Please any recourse besides buying a new washer? Does Whirlpool stand by the product?

I bought a gas range (#WFG524SLAB0) in July 2012. Two weeks ago, the oven stopped igniting. I called Whirlpool to have it serviced and they sent out someone from A &E Service Repair, who told me an igniter had to be ordered and it would take a week to come in. (He said he will order the part.) Then he told me to call Whirlpool again and schedule another appointment. Whirlpool sent out one of their techs two days later, who told me the same thing about the oven and said a part will need to be ordered. I told him it was ordered and he looked and said no part was ordered. So this was the week of Thanksgiving. Because the part would not be in until next week, no one could fix the stove until eight days later. So my Thanksgiving was ruined, no less with not being able to cook. So the service tech came to put the part on and the oven still is not working. He pretty much told me there was nothing he could do, for me to call Whirlpool again and have someone else look at it. I called Whirlpool and actually spoke to a supervisor who basically told me the same thing I have been hearing for two weeks: “We will send a service tech to look at the problem.” Keep in mind the stove is only four frigging months old. So here I am waiting again for someone from Whirlpool to fix my oven.

Whirlpool gold series refrigerator leaks water from freezer after 14 months because ice builds up causing the door not to shut properly and rime ice forms over food. I called Whirlpool and theyve not heard this problem before and stated I should have gotten the extended warranty. This is ridiculous. The internet is flooded with people having the same problem.

Do not buy a Whirlpool refrigerator. This is the 3rd time I have to call in repair for the ice maker in 4 years. Water poured out on my floor for the 3rd time ruining my floors. Called Whirlpool and said there is nothing they can do to help me. They don’t care about their Customers! I could have bought a new one by now based on repair costs. They don’t back their products. I’m really annoyed now!

Doesnt wash clothes properly - often some items of clothing just dont get wet. After 3 years the whole main bearing in it failed, causing unbelievable noise and constant overload faults. All Whirlpool top load washers have this critical design fault where water leaks into the main bearing (the bearing is an unsealed type with a cheap grommet seal) and then after a year or 2 the bearing starts to cease and the machine overloads itself trying to operate. Replacing the bearing means pulling the whole machine apart - and with a cheap press-fit bearing like this, special tools are needed and it will never operate smoothly again anyhow. In any case in 2 years, the faulty bearing seal design will let water destroy the bearing again. Effectively it is not repairable. Sounds like class action to me. So, it became an $1000 paperweight and I bought a new Samsung unit. I assume the Koreans know how to design bearings and seals...

My elderly mother purchased a Whirlpool Washer Mode Number WTW4955HW1 in November 2020. The washer has had nothing but problems. It leaks, vibrates and moves on the floor. My mother called Home Depot to see what she needs to do, and they said once they deliver the product it is out of their hands. Had our first service call in May 2021 by an authorized service and he said they should sell this on eBay. It is a horrible product, he said there is nothing he can do. Had a second authorized service in June 2021 and they said we needed a new tub which they ordered, and he said this will take up to 2 months, they also said to do only small loads and only use the deep-water wash and deep water rinse. After the technician left the agitator now comes apart. Would not recommend this product to anyone and I would never buy anything at Home Depot because they do stand by the products they sell.

Purchased a GGE388LXS04 electric range in June of 2013 from Lowes. In September 2013 one of the top burners went out, under warranty Whirlpool repaired the burner. Now after attempting to use the self cleaning mode for the oven, the ovens (top and bottom) along with warmer device do not work at all. This issue is evidently a major issue with Whirlpools electric ovens. Will call Whirlpool tomorrow as the oven is still under warranty, will also call Lowes and see if they will replace the oven with an oven with a comparable brand. Wish I had read this site before we purchased this oven. A very bad experience.

Since buying a Whirlpool Cabrio washer about 3 years ago have had several breakdowns. Within 6 months the computer completely failed. Since then it failed again. About every six months it costs me around $125 to get it running. The thing is a piece of junk. If the load is slightly unbalanced it just shuts down during the spin cycle. The old Maytag we had ran for over 25 years with the belt replaced once. No other problems. Will not buy another Whirlpool again.

I purchased a Whirlpool microwave oven from American Furniture/TV in Fenton, Missouri on 11-13-2010. It had a Whirlpool 1 year warranty and a Performance Guarantee for five years. I noticed recently that the plastic on the door had hairline cracks near the handle and now is beginning to crack around the glass on the front door. I called American when I noticed the cracks by the handle and was told that it was cosmetic and not covered. Now the cracks around the glass may be a bigger problem if they let fumes out from the microwave. I am waiting for a second answer from American. I feel like the problem is with the plastic itself.

Dishwasher (WDT710PAYM5) handle on the left side loosened within 2 weeks of purchase. Today the handle fell completely off. The dishwasher will be a year old in August of this year. I cannot figure out how to reattach the handle and there is nothing I can find in the owners manual to help me. There are only two of us and I am the one who uses the dishwasher. This should not have happened. Not real impressed with this machine.

I purchased my Whirlpool refrigerator from Whirlpool guest system (online) in 2010 for around $1,160. Recently, it stopped dispensing water from the dispenser. I called the Whirlpool certified A&E serviceman to repair the dispenser. He concluded that the water line is frozen inside the door. He also stated that such issues with the door shouldnt happen for at least 10 years. He gave me a bill of $920 to replace the door. I called Whirlpool and they declined to pay for the repair as it is out of warranty. I feel that they sold me a faulty refrigerator and they should pay for this expensive repair. With $920, I can probably pay for a new refrigerator (not Whirlpool, of course). I am completely disappointed by Whirlpools customer service and poor quality of their product. This company, I believe, is more interested in selling crappy products, make profit and not provide good customer service. Shame on you!

I purchased the extended warranty for my refrigerator and the warranty company sent a technician out to repair my refrigerator. It has been six weeks and 4 attempts and no one can do anything to fix it. The warranty wont refund my money without deductions from the company coming out and fixing nothing and says itll take 2 weeks before I can get that. After mailing in writing that I want to cancel 500 dollars wasted and no one wants to help. Thanks Whirlpool. Ill definitely let all my family and friends know of my experience.

Reading the reviews on this I figured I would chime in. Same problem with the top rack, its unfathomable how cheap this was constructed, since I have had old school dishwashers 15 years old without even close to a similar problem. Bought in 2012/2013 and have had this problem on and off the entire time. Looking at a new one definitely not a Whirlpool!

I bought a new Cabrio washer in August of 2011, and by December of 2011, it sounds like a jet engine when washing or spinning. It is still under warranty, but it is the same issue reported by countless others as I have discovered. Whirlpool should recall and find out what the problem is so that every consumer does not have to experience this issue.I will never buy Whirlpool again and I am going to make sure I spread the word about this machine to keep others from this experience.

We purchased both the Cabrio Whirlpool washer and dryer approx. 3 years ago, while still under the manufacturers warranty the lid cracked upper right corner. It was replaced and we were told by the repairman at that time this is becoming a common problem that he himself has seen this exact failure to several of these washers. Whirlpool needs to fix the problem. Shortly after this happened we receive in the mail the information for the extended warranty. Due to having this already happen, I phoned the extended warranty department for Whirlpool and specifically asked if this same thing happens again will it be covered under the extended warranty. My answer Yes.Well it happened again, called extended warranty provided them with a detailed description of what happened, they would send someone to replace, the service gentleman arrived today, called Whirlpool and they denied the claim. So they LIED. I instill honesty in my children and am proud to say I hold honesty as a high value. We were told it was cosmetic, the glass is buckled and the lid has to be held down to engage the lock mechanism of the lid. COSMETIC, this is a SAFETY concern. Where have our American values gone... Whirlpool used to have them back in the day... Shame on you Whirlpool.

Purchased Whirlpool free standing smooth top range at Sears Outlet (scratch & dent) in Columbus, OH on December 8, 2012 for a rental property. On May 18, 2014, tenant said she turned the oven on to preheat and turned on one of the front burners. She said she was at the sink preparing food and heard a loud noise; turned around and there were flames coming from the top of the stove. This didnt sound logical so I called fire department and spoke with one of the firemen. He said there was no evidence of anything in the oven or on top of the stove. Tenant said only thing she noticed is that there was a clicking noise coming from the stove a few days prior. After reading all of these complaints, I dont think I will buy another smooth top Whirlpool electric range. Luckily no one was hurt.

We bought a 20.5 cubic ft Whirlpool refrigerator. 2 months later it started cutting off, and on in a constant repeated cycle then run normal for a while. We had 2 Whirlpool repair appointments. The first guy said he couldnt come fix it unless it was acting up while he was here which was a intermittent issue. Refrigerators dont perform on cue. The 2nd guy came out after the first guy messed around long enough for the warranty to expire. We went ahead, and replaced the startup relay (most common problem). He replaced the control board, and wire harness. He said if that didnt fix it he didnt know what else to do. 2 hours after he left the fridge was right back to doing the same thing. He failed to report back to Whirlpool that the fridge couldnt be repaired. We contacted customer service, and their resolution was to get another repairman to come out, and replace the control board which had already been replaced. In the end they bailed on us, and left us stuck with a broke refrigerator, and we had to buy a new one ourselves. I might add it was not a Whirlpool. They spent $471 trying to fix a broken fridge, and wanted to send another repairman (another $100) to fix a $629 refrigerator how does that make any sense. It was a very disappointing experience, and Whirlpool should be ashamed.

Our Whirlpool Cabrio Washer is barely over one year old, and its getting increasingly louder (I cant hear the TV in the other room). I researched this issue and found this is a common problem with the upper and lower bearings. Check it out on YouTube; its easy to find. Whirlpool should buy these back! Is anyone aware of a class action lawsuit against Whirlpool regarding these pieces of junk?

I am not pleased with my self-cleaning oven. I dont even use my oven that often and I cannot get off even the simplest of stains on the sides, top, and bottom. I have tried to clean the oven three times and the stains from pie drippings are still not coming clean. It should not be this hard to clean an oven because my last oven was so much better and it was not Aqualift. The top of the oven is also very hard to keep the burners clean and looking like new. I am very disappointed in this oven and believe that this is false advertisement to the consumers. I pride myself in keeping my kitchen looking clean but this just is not working for me!

This product deserves ZERO stars! I purchased a Cabrio washer - dryer in October, 2013. I have carefully followed the instructions for the washer. I am hugely distressed about the large amount of money I spent on a washer that is absolutely terrible, horrible, awful., no words can adequately express how bad this so-called washer is. The low-water washing has torn up all of my new towels in the matter of a couple of washes. It has completely ripped out the hems of the towels and pulled long ragged strings in the towel. And these were not cheap towels. I am mad at myself for not researching better before buying. I hope my complaint can save another consumer from the misery I am suffering because of this shameful product.

I bought a Whirlpool Duet Frontload washing machine and now two and half years after buying it, it sounds like the tub is about to spin out of the machine. The repair man said it would cost over $750 to install a new tub and bearings in it. I thought the product would have lasted longer than two and a half years. I will never buy another Whirlpool product!

This washer has no agitator. Drum will shake back and forth while load of clothes will stay in the same place sliding towards the opposite direction of the movement for 20 minutes. Clothes are not turning, no going up or down, just staying still and not getting washed as expected. Baseball cap and construction worker jeans didn’t washed as it should have been.

My Whirlpool Microwave was installed in my new home by the builder. As write this, my microwave is 1 year 2 months old. Just out of warranty. On this day first the turntable wouldnt stop turning with the door open or closed. One hour after this event, the interior light would not turn off. On half hour after this event...the microwave died.

We purchased a Whirlpool dryer almost three yeas ago. Its a front load, steam dryer--or WAS should I say. Almost a year ago, I was unable to calibrate the control panel (in other words, to change the cycle). Ive been advised by the tech that I need a new control panel $200. Really Whirlpool??? A $500 dryer that lasts two years?

Last week dishwasher leaked. Set up repair with our local gas company that has service plus. Came today. Repairman showed me there is a hole in the bottom of the tub. Upon closer inspection it looks like the manufacturer drilled a hole that wasnt needed so they routed out a depression in the tub and must have put in some sort of plug or filler of some kind which now came out. I called Whirlpool and explained to lady about the defective tub. She said well if it had a plug of some sort put into the tub it would have fallen out before this. I said Well it didnt it just must have happened as it never leaked before. She said it is no longer in warranty. I told her this is a defect to me as if you drill a hole in the tub that wasnt necessary and then the plug failed that you put in to hide the extra hole. It is a defect not a warranty issue. Upshot is she wouldnt do anything about it. I told her I have always bought Whirlpool but if this is their policy its the last time I buy anything made by Whirlpool. After reading all the complaints registered here about Whirlpool I guess I am more than fortunate as my dishwasher (bought in 2006) had run great until their plug fell out (Great except for all the rinse aid that has leaked out for several years.).

I bought a washer and dryer a couple months ago. The washer has been completely replaced already. It is a piece of garbage. I have to wash my laundry four times and still my clothes are not coming out clean. I have three small children and it is just a pain to always be washing their clothes. Things as simple as orange juice not coming out of a shirt even using bleach. It was sold to me with high efficiency and great water consumption but of course it is, it doesnt use any water to wash the clothes. I had a tech come out to look at it and even they said its had so many complaints about how it washes. She said that the wash machine is the worst out there and I totally agree. If you cant wash baby clothes and get puke out of a bed sheet then I could just imagine grass stains. Wash machines don’t last forever but I can promise you I will never purchase another in my life. Best part of it is when whirlpool was approached, did absolutely nothing about. Basically said, “Have a good day, thats what you bought, thats what you get.” Considering its still under a year warranty. Tell me I will never buy a whirlpool again and I will never recommend one to anyone who asks. The customer service and product dont stand anything against other manufactures. I learned my lesson the hard way but Ive opened my eyes. Never purchase a top loader. Word of mouth travels fast. I know my complaint probably means ** to whirlpool but for what its worth, Ill be spreading the word around.

I bought the WP Cabrio washer on 10-18-16 from Lowes. It does not wash well, my dark clothing came out with white spots all over them even after I rewashed them x 3 and the lighter clothing you dont see the spots so you are wearing dirty clothes. Also, it is making a lot of noises while running. WP should pull this model off the market.

I apparently am one of the lucky ones to have an electric water heater. My unit started giving me failure codes during the Christmas holidays. Each time it would fail, I would get a different failure code indicating the upper element, the lower element, and a sensor failure. After testing all 3 of these components, it was determined to be a controller issue. After speaking with Chris on the phone, he overnighted a new controller to me. I installed the new controller and had no more failures. Hot showers for New Years! Thank you Chris.

We bought the Whirlpool duet washer & dryer in the winter 2011. The washer is absolutely awful. I have to keep it set on the Whitest White setting so every load gets a second rinse. In order for my clothes to smell CLEAN I use bleach in every load I can. With the loads I absolutely cant use bleach in, I have to be standing waiting to put the clothes in the dryer or I have to rewash the entire load because of the smell!! My towels are ruined from the bleach and my clothes are faded because of the multiple wash cycles. I have used the recommended Affresh numerous times and it does not help! Needless to say this washer was a total WASTE of money! We will be purchasing a new washer very soon! It will NOT be Whirlpool!!

I bought a new Whirlpool refrigerator from Sears and within a month the refrigerator side did not maintain temperature where milk would not spoil... Cool but never cold. I called Sears and they said its Whirlpool warranty to contact them. This I did and about a week later they contacted a local service company they use to maintain their equipment... Long story short this will be the 4th time they were informed the refrigerator still doesnt maintain temperature... Food had to be thrown out because of that.I asked them to refund me my cost or at minimum get a working refrigerator to me because after 4 attempts at trying to fix the problem it still exists... They just want to keep sending a repairman out there who still cant figure out the problem and that has cost me much time away from work not the mention the spoiled food costs... Even when complaining my dilemma to the repairman he said, All they will do is keep calling us and kick the can down the road... They could care less about what it has cost me in time and money... I had to give 1 star to this company but they dont deserve even that one... Dont waste you time thinking a warranty by them is worth a flip and now over 3 months Im without a refrigerator...

My son purchased the Whirlpool 2 door w/ icemaker about 3 years ago. Twice weve had a repairman here. Yesterday was the 2nd one. He tried 3 ways to get liquid to go through a round coil I could see at the back. He said the problem was between the two back panels (back of fridge & inside wall) where there was a tubing to release the water from defrost cycle. It appears to be a manufacturing problem. I am very upset! It should be replaced at the very least.

Bought wtw4800 washer brand new came with 1 yr. warranty. 19 months after buying plastic bearings went. 2 different technicians told me could not be repaired, junk. Washing machine less than 2 years old and can’t be repaired. Called Whirlpool. Told me they could do nothing to help me.

I bought a Whirlpool Gold refrigerator in 2010 from Lowes. Within months it had a Freon leak and Lowes had to replace it. I had bought the extended warranty. In 2011 a part had to be replaced twice due to excessive noise. Then the freezer got frost buildup on a coil in 2012 and again in 2014. I called Whirlpool and asked if they would pay for my next 3 year warranty. They said no, it was my responsibility after the first year. I would never buy a Whirlpool product . Do research, Whirlpool makes several brands.

I bought a Whirlpool refrigerator water filter from the Marcone distributor. This distributor, whose name I received from calling the 800 number in your manual, did not send instructions on installation. I called Whirlpool and they did not have instructions on installation. The product is 4392949. In talking with your customer service department filters, I learned that the young man knew nothing about filters. He told me that the filter that I purchased was the wrong one. Its interesting that he tried to convince me without knowing my refrigerator model number. I asked if he wanted the model number and he said, yes, please. It was very sad how I had to do a song and dance with an idiot. I had no help from your company. I will return this water filter because I was not provided instructions for installation. Neither can your people produce them. For this reason, I will never purchase Whirlpool again.

I bought it on 11-24 13. I called Whirlpool on 1-29-13 and got no response. I called 3 or 4 times and still havent heard from them. Its now 4-1-13 and still nothing. I tried many times and got the runaround from them. They owe me money for repairs to the heater. I will not ever buy from them again. Just thought you all should know about this.

Talked to tech & checked the manual for testing the thermocouple on my natural gas water heater. Everything checked out fine but pilot wouldnt stay lit. Tested thermal switch.... everything. They said replace the valve/thermostat. Still no dice. Turns out the thermocouple was cracked on the inside near the burner assembly & would give passing readings on the voltmeter 9 out of 10 times. If you have any pilot problems, replace the thermocouple first. Was only 10 bucks. I keep a spare now. Dont forget to vacuum any dust from the fine mesh screen on the very bottom. Fresh air supply.

I exchanged my fancy front loader Cabrio washing machine for a top loader after having numerous issues: clothes werent getting clean, extended water cycle, and a leak. The original purchase was made at Lowes, where I elected to invest in the 3 yr extended warranty plan. After several visits from their sub-contractor, they allowed me to exchange the washer for a top loader Whirlpool Cabrio. At first the washer seemed to work, but after about 8 months I started having problems. The bearings went out and when the service company replaced it they forgot to screw top of the machine together. During my first load, I heard this terrible noise and discovered that the entire top of the machine had separated from the bottom by 2 inches. I frantically rushed to turn the washer off before my laundry room flooded. So, they were out again and screwed the machine back together but failed to retrieve the original screw that they removed from the washer during the first round. Well, the screw got lodged in-between the drum and interior, causing it to completely break the machine. Lowes agreed to exchange the washer for another top loader Cabrio, but my 3 year service contract would not cover the new washer. Not to my surprise, I immediately had issues with it and had to hire a repairman to assess the problem, who concluded that it was the bearings. He informed me that it would be about $700 to replace the bearings and cheaper to just buy a new machine. I called Whirlpool and explained to them about all my issues, now becoming almost comical. They arranged for an outside contractor to assess it. After confirming that the bearing were bad they replaced them. Another few months go by before problems occur, this time the washing machine stopped draining water and spinning. The service company was out another 4 times. They replaced things like the mother board and control panel. My last appointment was today, where the service guy said, There is only one error code. It is a stuck button. I said, Will you at least witness a full cycle so I can show you all my problems: clothes still dirty and stinky, items still wet after spin cycle, cycle taking 2 to 3 hours to run, horrible noises, and timer adding minutes to original cycle. He called Whirlpool because he genuinely felt sorry for my situation. They were of no help. He didnt stay to witness a cycle. Moral of story: if the error code doesnt detect a problem, the consumer will not be helped (this is something that consumers do not have access to). They will happily call a technician out to put a bandaid on an issue until your warranty runs out. I have had between 7 to 10 service calls out to my house, requiring me to take either an entire or 1/2 day off of work each time. If I added up all time lost at work, I could have easily purchased a top-of-the-line washer/dryer duo and been done with all this Whirlpool foolishness. Do yourself a favor, stay away from this product.

Appliance repairman is coming tomorrow. Washer is less than 2 years old and will stop mid-cycle more than once (I re-start it)... At first when I thought the cycle was done I would get ready to move the clothes to the dryer and realize they were all soapy and sometimes they were just massively soaked so something is not working right. Sensor?? Hopefully not the computer panel as that will be too expensive to repair.

AquaLift Self-cleaning does not do the job as advertised. It does very little to clean the oven. Sitting-on-the-floor-in-front-of-the-oven scrubbing is what is needed to clean the oven.

My new washer quit working properly. It does not spin or wash properly.

A couple of years ago, we had 2 natural gas hot water heaters installed. We immediately had a service call to replace the thermostat on one of them. Then recently, the other one had to be replaced because of the leaky tank. It was still in warranty, and we had to pay $425 for the old one to be removed and the new one installed. Now, this one has a bad thermostat and the A & E Factory Service is coming tomorrow to install the new thermostat. We have been inconvenienced by this for a couple of weeks as we have no hot water in the master bath. We were just lucky that we had one hot water heater working in the other part of the house. I think that Whirlpool should have paid the $425 for the installation as the original hot water heater was in warranty. Now, I hope that tomorrows visit will be covered by the warranty. Next time we need an appliance, we will not be purchasing a Whirlpool.

I purchased French door refrigerator WRF989SDAE00 3/2014 from BrandSmart to upgrade from a side by side Kenmore purchased in 2005 with my home (no mechanical issues with my Kenmore and thank goodness I kept it in the garage). Within 2 months the freezer would not stay cold enough to freeze ice cream and Whirlpool sent an authorized repair company (FLAMINGO APPLIANCE SERVICE) to replace the compressor. Well this became a reoccur theme every 2 - 2 months the refrigerator has an issue with maintaining temperatures cold enough to freeze ice (so puddles of water all over the floor from melted ice in the ice maker) and forget about buying ice cream. We have not purchased ice cream since the second time this piece of junk broke down.This is my FOURTH REPAIR (3 COMPRESSORS, 1 EVAPORATOR, AND, 1 CONTROL PANEL). All but the last repair occurred during the warranty period but Whirlpool refuses to replace the unit. Side note: I also purchased a Whirlpool dishwasher the same day as my refrigerator and it also stopped working within the same week of the first refrigerator repair. So far I have not had any issues with the dishwasher. I WILL NEVER PURCHASE WHIRLPOOL APPLIANCES... NEVER!!!

My $800 Whirlpool Cabrio top loader does not rinse the soap out of the clothes. Nor does it even get the clothes completely wet. After the final cycle I have soap scum in all the wrinkles of the clothes. Most dissatisfied purchase I’ve ever made. The one-star rating comes from the pretty blue digital displays. I’ll be purchasing another; this one goes to the dump where it belongs!

This range is easy to clean, easy to use, multi functional burners, easy to use oven and very nice looking. We use propane instead of natural gas and the conversion was quick and efficient. We absolutely love the griddle.

Hello, Here is our story. We bought this refrigerator Whirlpool - 26.2 Cu. Ft. 4-Door French Door Refrigerator through a local reputable retailer. After 16 months we started to have problems with ice melting in the ice bin. We continued to have problems related to cooling/freezing within the refrigerator to the point where almost all the major parts were replaced. The good news is the dealer negotiated with Whirlpool to have all repair costs covered after the first visit. I asked about just getting us a new refrigerator and was told Whirlpool requires a part to be replaced 3 (THREE) TIMES before consideration.In summary, the refrigerator could not be fixed and was condemned in agreement with both Whirlpool and the Dealer. Here is the interesting news - since the refrigerator was out of warranty (12 months and now we are at 18 months), they are requiring we pay $600+ for the replacement. Buyer beware - either pay for the extended warranty or risk having to be inconvenienced by having your refrigerator unavailable for days or in our case, weeks!

We bought a Whirlpool Cabrio washing machine a year and a half ago. It started making loud noises over time and finally stopped. Whirlpool did advise us that it was out of warranty but suggested they send a factory repairperson out. They told us depending on the problem they might pay the bill. It turned out that a nut holding the pulley had not been tightened up properly at the factory and had no restraining device, so it simply rattled off over time. Since we dont use the machine that much, the problem went past the 1-year warranty. It cost us two hundred and fourteen dollars for repairs. I could have put the nut back on myself for free. The service guy also said they had multiple similar problems and I should contact Whirlpool and they would probably work with me. No chance. They only kept repeating that it was out of warranty. I even talked with a supervisor who said the same thing. I asked to appeal further and she refused to give me anyone else I could contact. I asked for their legal department information, and she said she did not have that and I would have to get that through my attorney. What a joke. No more Whirlpool for me.

Easter is in five days. Our dishwasher purchased in December 2014 is not working. It has been broken since December 2015. Repairmen have been here THREE times. We were told that our warranty only covers parts and repair. Our dishwasher does not wash dishes. We went for a more expensive model and it didnt last a year. Whirlpool, remember your commercial?

I paid big bucks for a five burner, convection stove. I had a pot of boiling water on and the steam melted the plastic cover over the controls. Whirlpool said I had to buy the whole electronic panel. Close to $175.00!

Our 2 yr old Whirlpool Gold refrigerator (French doors, bottom freezer) stopping freezing/cooling. When we got a repairman to come take a look at it, he said the compressor is not working. The warranty on the fridge is only 1 year. However, the compressor is the main component of a refrigerator, and the repairman said 5-6 years is the minimum it should last before breaking. I called Whirlpool and asked them to pay for the repairs of what is quite obviously a defective part. They refused. Needless to say, I will never, ever buy another Whirlpool product again.

I just replaced a 4 year Cabiro washer with a Samsung. The washer was making terrible loud noise when spinning. It sounded like a jet plane. The repairman said it was a bearing that was going out and that it was a common problem in the Cabiro washers. Cost to repair it would be $500.00. Last week, it finally started spewing oil from underneath so had to buy a new washer. I will never, ever buy anything made by Whirlpool. Whirlpool said it was off the one year warranty (duh) and they wouldnt help with repairs.

I have a one year old Whirlpool refrigerator which was fine for 6 months. Since then it has been a nightmare. If Lowe’s had not intervened on my behalf, I never would have gotten service. Have had at least 6 service calls, 2 new ice makers and various other parts. It should be bright yellow.

Bought a Whirlpool hot water heater from Lowes 1/08/12. In May of 2013, it would not work. I had to replace the Gas Control for around $100.00. It was 4 months off warranty! The same thing happens 3/2014. They sent me a new Gas Control Valve free and shipped it overnight. This is no fun to fix. I cannot believe that I need to flush the tank out with cider vinegar every 6 months. That is why I was told it keeps breaking.

I purchase the front load, energy efficient brands, low water usage. Love Whirlpool; never had a problem with their appliances. Front load, low water usage, clothes dont sit and spin in dirty water. Dryer has multiple cycles. Perfect for the whole family. My last Whirlpool set last me over ten years, wanted that same quality level in my new purchase. I wanted a quality machine. I was very familiar with the Whirlpool brand and knew that was going to be my first choice in a brand. These were full size. The tub is large enough to hold a king size comforter and wash it without destroying it. The dryer has a separate attachment for pillows and shoes (sneaker plus) and was competitively priced at the time of purchase.

Purchased a Whirlpool Cabrio Washer a few years back... Started getting F1 error message and just proceeded thru it like most did initially, but now has become pain in the rear just to do one load of laundry as we get the error 2-3 times when we start each load - then on every load w/ 21 minutes left on the cycle. From the looks of things online this is a chronic problem and should be fixed by manufacturer. I called Whirlpool customer service and first person I talked with said they understand it is an issue but no longer are any recalls or reworks on that machine. I asked to speak w/ supervisor and sat on hold until I got one. Was then informed they do know it was a problem but was not something they could do anything about other than schedule a service company to come take a look. I specifically asked if there was at one time a recall or if they were fixing this issue for a while. She said Yes, they took care of some of their customers but are no longer doing that for this model. So basically because I didnt call in at the right time I need to fix my machine myself. I said it will be the last Whirlpool or Whirlpool associated appliance I ever purchase if this is the kind of customer service I can expect... The supervisor just said she was sorry to hear that and to have a nice day. Hopefully enough people read these reviews as I wish I would have before purchasing my Cabrio and dont buy Whirlpool.

We have the Cabrio model and are thoroughly pleased with the performance. My only issue is the amount of sounds during the spin cycle. Otherwise, the machine is quiet. I like having the automatic dispensers for soap, bleach and fabric softener. Not having the classic tub makes loading a little different as the clothes need to be distributed around the side of the tub and avoid the center.

We purchased a Whirlpool Cabrio washer 6 years ago. This washer has been such a terrible appliance, I would not recommend that anyone buy one. The top of the washer has broken 2 times. Whirlpool will do nothing about it. It is a manufacturers defect where the glass pops out of the top and then breaks the frame it is in. We had it replaced last year and the new one is now broken - same problem. It also does not get clothes clean and the clothes get ruined because they become all entangled in one another. We will never purchase a Whirlpool appliance again. I did have a 5 year service contract on these appliances but once out of warranty - you are on your own.

We bought all whirlpool appliances at our new home 4 months back. Our refrigerator has stopped working from the last month. We had 7 different service team people come in to check and they temporary resolve the issue (taking out a plastic piece from the top of the refrigerator, just re fixing the ice machine, or just walking out of our home doing nothing).Friday someone came and tried fixing it and took about 3 hours. The fridge completely Broke down after that in about 6 hours. Whirlpool customer care wants to send another technician in and want them to have them talk to their technician and maybe after that they can do something. This is the 8th time some technician will be coming home. And clearing these technicians curse whirlpool and dont call them. The customer team at whirlpool suck, there is no damn replacement or repair policy. All scheduling is after a week and whirlpool does not give a **. I really hope this company is sued for the emotional and mental stress and the harassment they cause to their customers. Very frustrated. Have no idea what to do.

I purchased a Whirlpool dryer Cabrio (model # WED7300XWO and serial # M03028918), which has had several issues. We had to replace the felt around the dryer tube twice, replaced the dryer tub itself twice, we had the air flow stop, and now the heat has stopped. Thank goodness I purchased an extended warranty, otherwise who knows what these repairs would have cost. I think I got a lemon. I have had multiple repairs, and days of not being able to use our dryer.

Friends and family dont you ever dare to buy a refrigerator from Whirlpool - Best Buy!!! They sold me a defect refrigerator and after 2 months begging to see a technician, they are telling me that they are going to fix it. Im so tired of them trying to fix it. Theyve been here 4 times with no luck. All my food is rotten and frozen. And its a new refrigerator. Gosh. As you can see, the water in the plastic cup that I left in my refrigerator are frozen which is not supposed to happen. I feel that Im dealing with nonsense. They dont care. They just took my money and thats it. Im left with a new defect refrigerator that doesnt work. Ridiculous.

We bought a house almost 10 years ago and it included a Maytag washer and dryer. About 5 years ago, we decided to buy the Whirlpool front loaders. What a mistake as the washer shook every time it ran. After several warranty service calls and days of vacation waiting for the service, they finally said they couldnt do anything. During that time I had been in contact with Whirlpool and asked for them to take them back. Of course they wouldnt. I asked for a swap for top load washer and they would need to also replace the dryer to match: still no deal. It took a letter from a lawyer to make it happen. They also bought back the washer and dryer stands which covered the lawyers costs.So shortly after I received the Cabrio washer and matching dryer, the lid is very heavy which I believe the lid spring broke. I refused to call the service company as I did not want to go thru that crap again. I also know I can fix it myself easier and without all the drama. I keep waiting for another failure but so far all is acceptable. Whirlpool is not the same company as they were when I made my living doing warranty service for Whirlpool! 30 years ago they were the best in the industry.The Maytag pair was giving to our relative and they are still working flawlessly. Unfortunately Whirlpool now owns Maytag. This experience has cost Whirlpool replacing our kitchen appliances. As much as I want to buy American, I will go with Bosch or LG only.

I own a Whirlpool Cabrio. I wanted a newer technology (no agitator) washer with top loading capabilities. I ended up with a four to five-year lifespan with this washer. The bearings are busted and it leaks water from the bottom. I have followed loading instructions specifically. It will cost about $1,000 to fix so of course, I am buying another washer and a matching dryer.

We have a built in double oven and we had some early problems with the thermostat. And from time to time the clock resets to 12:00 oclock when there is no other power outage indications. Its also been a challenge understanding the instructions sometimes.

Why would I, and others buy Whirlpool made washers, with all of these service problems? Now I understand why they have profit/loss statement problems, and stock prices in the pits.

After being a faithful Whirlpool consumer for years... I no longer have any faith. I purchased an entire kitchen suite. The side by side refrigerator Nov 2013. The first refrigerator was delivered with the side cabinet deeply dented in several areas. Another was delivered 4 weeks later. Silly me... I thought, Okay, no big deal... what could go wrong? I didnt take time off work again to receive the replacement. My son took delivery (never looked at it). I get home... the front of both doors looked like they had been kicked in all the way across! To add, the cabinet sides were textured (not smooth like what I ordered) and the door handles didnt match the other appliances. So, I called HDepot & called Whirlpool (only to be on the phone an hour each time due to high call volume. Imagine?). Then Whirlpool reps are talking to me like I am some sort of idiot... saying that the refrigerator was EXACTLY the same... not possible that the handles or sides were different!!! Because it was damaged (and I mean ridiculous! ) another 8 weeks for a replacement. Frig #3 arrives and I take time off to receive it. Ah, the right refrigerator... but again ~ handles dont match. Not POSSIBLE.. Ms. _ _ _ _... it is the exact refrigerator, those are the same handles. Hours and hours on the phone to HDepot and Whirlpool. Finally, HDepot rep has a WP rep at the store when I call, and bingo! Oh yes, there are two styles of the Exact same model. The handles are ordered... 10 weeks later I finally have matching handles! But, wait... gets better. The fridge has been loud from the start, CONSTANTLY running but, not cooling some areas and freezing in others. Then when you open the freezer it is like a burst of winter wonderland is unleashed in your face. There are sheaths of ice building up on the top of the inside door. Hmm, I think what is going on? The Whirlpool designated repair company comes out. Ah, well here is part of your problem. When the refrigerator was being put together they left a few thicknesses of blue packing tape between the door and the rubber seal in the freezer. The rep tried to fix it to no avail because the door was also warped. First they were going to replace the door. Waiting for another 10 weeks. Nobody calls, whats going on? Oh, never mind, or rather... that was never happening. I have spoken to many reps with Whirlpool, I have been polite with all. In turn, from most I get curt hard ball back. The offers to resolve this from Whirlpool have been ridiculous. I am sorry for my loyalty to Whirlpool, as it has not been reciprocated. I have had two more deliveries - both the wrong unit! I never thought there were others out there. What a mess. They should recall.

This refrigerator well paid for itself. I had over 25 years and it was still in good working condition. I had to leave it behind. I moved to a place where fridge was already. I hated to leave it behind. ‘twas offered to Goodwill but they never answered the phone for it. I surely hope someone got it.

Purchased the Gold Series Dishwasher Model No: WDF730PAYM0 Serial No: F14403489 on Dec 2011, started using it from Jan 2012. All is good until June 2014. It started leaking from the bottom, called Whirlpool - the great bad company. Since it is not under warranty they asked to schedule an appointment with their local authorized rip off service company. Technician come on the service day and told me that it is $120.00 for the service call and Labor and parts are extra, first of all $120.00 to come to my house is first rip off, that is the reason Whirlpool on their website do not give any estimates on the service call.After checking the appliance he said main assembly is bad and needs to replace and that will cost more than the original purchase price - what a ripoff. He asked me to contact Whirlpool, they may help since this is the known issue with this model. Called Whirlpool and mentioned and they said it is too old to continue to operate so they cannot help. Ended up trashing the 2.5 year old dishwasher for the new GE dishwasher. Never buy a Whirlpool ever again even on sale. Whirlpool company is not ethical and not ready to help consumer, would love to see them close their operation in America.

Our first Whirlpool washer barely lasted 1 1/2 years. They replaced it with another one that broke within 9 months. When it worked, it was great... When it didnt, it either overflowed or did not wring clothes tightly on the second rinse.

I have been TRYING replace a damaged panel on a $10,000.00 Jenn-Air refrigerator for over 10 months now!! Whirlpool is the supplier of Jenn-Air - I have probably spent at least 3 HOURS on the phone talking with one rep after another who ASSURES me they will deal with my problem!! Last week I gave my credit card # to the rep - who told me my part was sitting there, waiting for my # to be shipped. When I asked why no one had called me to let me know, especially considering the amount of time I have been waiting - she said she didnt know. One week later, I call AGAIN to find out why my credit card does not show the payment. Only this time to talk to a fellow who says my part is still on backorder, and they used my card # to put a $1.00 charge against it - to hold it for when my part arrives.. BUT has NO IDEA when that may be! I feel Angry, totally discouraged, lied to, and used! I will NEVER purchase any appliances under the Whirlpool affiliate. This is abhorrent customer service - a $10,000.00 appliance and this is how it is dealt with!!! Bad, very bad!!

We purchased Whirlpool Gold Accubake, double ovens (gas) in 2005. Since then, we have experienced identical failures (8 to date) during the self-cleaning cycle in which the high temperature burns out the thermal fuse of the ovens. This requires two Sears technicians to repair the unit (it requires two technicians to pull the oven out as the fuse location is in the back of the unit) and leaves us without use of both ovens for approximately 2 weeks (scheduling parts delivery and technicians through Sears home repair is not an expedient process).After checking other consumer product websites, it has become clear to me that there is a known design defect with these ovens in which the thermal fuse is not adequately insulated from the high temperatures during self clean; it therefore trips and burns out during the self-clean cycle. While not having access to ovens for about two weeks/year on average may sound acceptable to Sears, the reality is that the problem has escalated in frequency since purchase. In 2013, we are going on our third repair of the same problem (that makes 6 weeks of non-usable oven time in one year) and Sears will not consider replacing the unit, despite: 1) our obvious dissatisfaction with a lemon unit, 2) a well documented history of the defect with this particular Whirlpool oven and 3) an ongoing and escalating repair cost to Sears (it is under their extended warranty so the repair cost is on them although we did pay for this service up front on our appliances).I would stay away from not only Whirlpool appliances but also Sears as there doesnt seem to be any regard for the customer experience and taking care of a product problem (the right way) with a known defect. Sears has an opportunity to make this problem go away quite easily and retain a customer - fix the problem permanently or just replace the defective unit. Unfortunately, my experience to date with Sears standing behind the products they sell provides me with little confidence that either will happen.

In my wildest dreams I wouldnt have expected that changing a burned out light bulb on a 7 month old microwave would put us out of commission for over a month. Its been 30 days now and Im told it will be more than 2 weeks before the part comes back in stock. Whirlpool had such a good reputation years ago, but thats history. This is a disgrace.

Whirlpool refrigerator Model type 14TFA seems to really keep things cold with good airflow in the freezer, and below shelves in bottom half are also keep cold adequately. Standard white appearance... somewhat boring.

I purchased this Whirlpool washer (model WTW7600XW2) on October 2011. Fabric softener dispenser is full of water at end of cycle. Repairman has replaced parts three times, but the problem is still not corrected. Today, I talked with a Whirlpool supervisor. She says this is normal. She told me to take the cup out and empty it. The cup is not removable, so she said I could blot it out with a cloth or sponge. I paid $800.00 for a washer with an automatic fabric dispenser that I must empty manually. I have used whirlpool appliances for 50 years of marriage, but this is my last one. I am very disappointed with customer service.

In 2013 we thought that we bought a 30 cubic foot refrigerator model no. WRF989SDAM from Appliance Direct, Melbourne, FL. Months later we realized that it was only a 27 cubic foot unit. Two months after the warranty expired the unit started failing. Called the dealer and was told that they would have the service department to call us. Never heard from the dealer again. Finally I called an independent service company. After testing the unit the technician told us that the evaporator may be leaking. They offered to replace it for a price of nearly $500 with only a 90 day warranty. Realizing that it would work at least 90 days after the repair regardless if that was the problem or not.I decided that we did not want to spent that much money. Having refrigerator experience in previous years, I decide to add a piercing valve and adding refrigerant. Every few months I have to add refrigerant to keep the unit going. This unit has run nearly all time since the delivery. Corresponding with Whirlpool is somewhat like throwing a bottle in the ocean. I also noticed that Whirlpool has dropped the price of this unit quite a lot, must be to loss of customers. And yes I am 83 years old and handicapped and never had a problem like this to affect me so much.

We purchased the Whirlpool Cabrio washer and Dryer May 2017. First, this washer is SO LOUD! Honestly, NEVER had a washer that is this loud on the spin cycle. My second issue is, that when I wash my blacks, they have white splotches streaks on them. I use ALL clear and free liquid washer and Downy softener, so I stopped the softener, and still the white streaking. Ive since will use the additional rinse on during the wash, but still leaves white streaks. After 3 separate rinse cycles, no streaking. This leaves me thinking that with the lighter colored clothing, there is probably streaking as well, just can see it - my conclusion is that the clothes arent getting cleaned properly, or rinsed. Another issue is the dryer. First, takes longer than all my previous dryers, even the set 110 mins for towels on high, still takes longer. My washers are not packed tight with clothes either - its just my husband and myself - not a lot of washing. Also, I noticed a crack in the inside dryer/drum where it looks like the paint is chipping and cracked. I used some high heat touch up paint, and it did not help. Needless to say, what I thought was an good reputable product, turns out to be, not so good.

I have a front load washer by Whirlpool and a motor stopped working on the drain. When I called them, they told me it would be $200.00 for the part. I dont understand why they dont stand behind there product. What can be done to make these people fix there stuff? This is there product, if they cant do it right, then find a new job!

Are there negative numbers for ratings? Horrible, to say the least. Whirlpool is the parent name for KitchenAid ovens. I have an electric oven and the glass on the front door exploded! Whats worse is that I have been given the complete run-around! I have called, wrote, waited, and tried ordering through other companies--still no luck! How does Whirlpool get away with this? It seems that Whirlpool no longer makes the part!! Do they really expect consumers just to replace an oven every few years? Poorest customer satisfaction I have ever experienced! This should be a consumer fraud grand suit, as there are numerous complaints about the same issue with Whirlpool appliances! Stay away from this company by all means!

Ive trusted Whirlpool washers for 20 yrs. Ive only had to buy 2 in my lifetime and neither have let me down. I will always purchase Whirlpool as it is a brand I can trust. Features and reliability are important to my family. Whirlpool has it all!

We purchased a new home in July of 2011 and we paid extra for the upgraded appliance package, which included a Whirlpool Microwave/Convection Hood Combination unit. We have Model # GH7208XRS3. We use the microwave a few times a week and only used the home 6 months each year during 2012, 2013 and 2014, for a total of approximately 18 months. From the very beginning, we had trouble with the microwave control panel turning itself on and the electronics going through various timing and programming functions independent of any human operator.During the combined two-year warranty period from July 2011 July 2013 (the Manufacturers Warranty lasted one year and the Developers extended Warranty lasted an additional year) we had 5 service calls on the same issue. The Authorized Repair Center repairman called the Whirlpool Tech Line while he was in our home and was told that there was a flaw in the design of this model. They replaced the door and then when it acted up again, they replaced the control panel. In Nov. 2012, after the repairman told us the door needed to be replaced again, we asked for a new appliance since we had the same issue repeatedly and they had already tried to fix it by replacing the door and it was still under warranty. We were told that Whirlpool would not replace the appliance until they had tried to fix it three times and we needed to get a new door again. We were told that because it was the same issue repeatedly, we would get a replacement if it still went bad after the warranty was up. So we had the door replaced again, which did not fix the problem.In late 2014, we again had the same issue with the control panel and made a call to Whirlpools Customer Experience Center. At that time, we were told that the warranty was no longer in effect and Whirlpool would do nothing to fix the issue. Even though it was the same issue that they had attempted and failed to fix while under warranty, the company would no longer stand behind the promise of customer satisfaction and told us they will not replace a 3-year-old microwave. When I asked the Customer Service Rep to speak to a Manager to escalate the issue, I was transferred to the Tennessee Office. When I got the same repeated run-around from the Supervisor, Melissa, I asked that Customer Service Supervisor to let me speak to a Manager and she told me she could not give me the name of anyone else to speak with and hung up on me.I am writing to you to express my extreme disappointment in Whirlpool and the products reliability, the way the company has handled fixing the problem and especially in the conduct of the Customer Service department. Whirlpool gave us nothing but a run-around for the years the warranty was in effect, knowing that this model has a design flaw and trying to do band-aid fixes until the warranty ran out. We were told that our only option now is to pay to have the same problem fixed a fourth time or purchase a new microwave.Whirlpool has trained their Customer Service people to be polite but ineffective and obstructionist on the phone and then hang up on the customer when they cannot resolve the customers issue. I believe that Whirlpool should be committed to customer satisfaction and making sure that their products work as intended and fix the problem that was reported while under warranty, even if it no longer in warranty. Whirlpool should be as disappointed as I am that after three attempts the problem is still not fixed and should be committed to customer satisfaction enough to replace the appliance after three failed attempts.

I purchased a Whirlpool Cabrio Washer In July 2014 for $937 cd. What a waste of my hard earned money! I have had nothing but issues with it since I purchased it. The retailer no longer sells them as they have seen nothing but complaints with them yet Whirlpool did nothing to help me as a client. It does not wash the clothes, there is such a foul smell even when cleaning it once a month as requested and the clothes comes out soaking and not rinsed properly. The technician came out and advised the washer was not broken. That is just the model. I have requested supervisors to call me back and most recently wrote the corporate office. I am out almost $1000 and in a situation where I have to go purchase a new washer as I just cant stand to use this product any longer. I am shocked they have not placed a recall on this model. What a poor product.

Cabrio he washer wtw6400sw2 - I bought this washer about 6 years ago at the time we paid around $900. Now my bearings went bad and the repair person told me it would cost around $300 to $400 to replace the bearings and seal and shaft but that I should call Whirlpool and see if they could replace the part or give me some discount cause it is becoming an issue with all the Cabrio washers. So I called and spoke with a so called manager - as far as I know it could of been a cleaning person there. She told me that she could not do nothing about the issue. So if a lawyer would be nice to help me and the rest of the world that are having all these issues to file a suit against Whirlpool Corp.

IM OLD AND DISABLED WOMAN. Bought a brand new $800 Whirlpool top loader washer and it wont work after not even a month. Called whirlpool and had the worst customer service from Tammy. I have to wait to compose myself to call back cause the washer is junk... F9E1 SENSOR. IM NOT A MAN! Worst customer service. Thought my washer would last longer. Its been 1 hour 45 minutes. Wont turn off. I CANT unplug TAMMY! IF I COULD I WOULD!

This washer is going back. It simply will not spin the water out of the clothes. It says it gets clothes drier than a conventional washer, but I have not found that to be true. I have to use the drain/spin cycle over and over and still the clothes are wet. I had the repair crew out and they were able to get it to spin out a very small load consisting of two sheets and two towels. Other than that, it does not spin out water. It is also very difficult to load if you attempt to leave the center open as they recommend. The cycles are very long. Not being able to look inside without pausing it and waiting for it to unlock is also a huge hassle. I am getting one with a glass top so I can see what is going on. If you leave it open for too long, it cancels the cycle and drains all the water, and you have to start over which is another problem because all your detergent just got drained out before the load gets going. It uses so little water on most of the cycles that the clothes get totally tangled up with one another. I think you should be able to choose the water level manually. I am all for saving water but if I want more water from time to time, this does not allow you to do that. I DO NOT RECOMMEND!

I purchased a Duet Front Loading Washer (model WFW9750) in May 2010. In September 2011, the noise level had become intolerable. I called a local service company. They advised me that the main bearing was bad. It would cost more to repair than what it was worth. I contacted Whirlpool. They could not do anything unless the machine was inspected by one of their authorized service companies, which they scheduled. Two weeks later, A&E Factory Service arrived and confirmed that the bearing is bad and the cost to repair will be $1,542.06. Whirlpool customer service transferred me all over the country to tell me that the machine was out of warranty and there was nothing they could do.

I bought a brand new washer from Home Depot, Whirlpool 4.3 cu High Efficiency Top Load Washer to be exact. It hasnt even been 90 days and it started to make the loud, horrible noise so we had someone come and look at it. Apparently the transmission blew and the oil leaked all over my tile floor. I work full time and I do laundry only on the weekends and there is only two people living in the house so you can imagine we do not use it that much. I went to Home Depot first and since it was past 30 days we had to called Whirlpool direct. The customer service is horrible. I thought since the transmission blew, they would replace the entire machine since that is the brain of it. NOPE! They said to replace the entire machine and give us a new one, it would have to break 3 times. Are you kidding me? They did not offer to reimburse the tile damage or the amount of money I had to spend at the laundromat. Not to mention its been over a week and the guy still has not come out and fixed the transmission. It would not be a big deal to me if the hose broke or something simple, but imagine if you bought a BRAND NEW car and the transmission broke 60 days after you bought it. You would take it back to get a new car. The customer service line could not care less about the issue. I spent over 2 grand in appliances from Whirlpool and I will never buy their product again because of the customer service and the fact they did not want to make the situation right. I just bought the machine brand new for a reason!

We purchased a higher end cabrio model only 3 years ago. Last year, on about every 5th cycle, the load would not spin at the end. Id have to remove all the wet clothes, set it to drain and spin, start it and wait for it to hopefully kick in. When I do it right, it kicks into the spin mode. I had to quickly press start/stop to unlock the hatch and reload the soaking wet clothes and wait for it to spin properly. Yesterday the same thing happened again. This time, it did not kick in. I ended up flipping the washer over and taking a look underneath. I discovered that the motor was seized. It had lost all its lubricating oil and smoked the belt. Now, my 3 year old washer is sitting in the driveway awaiting a trip to the dump since I got fed up and went out and purchased a new Samsung top loader. I emailed and called whirlpool with no luck. Not impressed. When I went out to buy a washer today the first thing I told the salesman was to stick anything with the name whirlpool out in the trash bin out back.

Whirlpool Refrigerator Model WRX9885IBM01 French Doors - We purchased this $2,000+ dollar refrigerator in December of 2014 and within two weeks of plugging it in, we noticed the freezer drawer was crooked and ice crystals in the freezer compartment. We contacted Whirlpool re the matter and they dispatched a local serviceman. He informed us that the inner lining of the refrigerator was crooked and he contacted Whirlpool. He sent pictures of the crooked drawers and was advised by Whirlpool to adjust the outside door, but nothing could be done for the inside crookedness and that he was to take silicone and seal the refrigerator to prevent air coming in to create the ice... Really? We told him that was merely a Band-Aid to the problems and we wanted a replacement. According to Whirlpool, they can only service our month old refrigerator and cannot replace it.Actually, they cannot even service the defective product they sell, they can only caulk the problem until it comes again. I am not going to stop until everybody in the country buying a refrigerator thinks first about the warranty Whirlpool offers. After reading defective parts, etc., I am amazed they are still in business! We are contacting Lowes to come pick it up! Let them deal with the garbage they are selling!

High end Whirlpool dual front loader washing machine model number WFW94HEXW2 died after 5+ years of less than moderate use. Used no more than once a week. Paid for a top end model. Had 2 mechanics look at it. Mechanically it is fine. The CCU is not working correctly and wont allow it to start. We replaced it, but to no avail. It is barely out of warranty at 5+ years old. Called Whirlpool and they said they would do nothing. Asked for a manager and she was rude to add insult to injury. Cant get to the serial number because the door is locked shut as part of the shutdown problem. Cant find original receipt so including a picture of the credit card purchase. Trying to contact retailer but so far have not heard back from them.

Whirlpool Cabrio Model WTW6500WW1 - Have had good luck with previous Whirlpool Washers so thought I would purchase this one 2 years ago from Menards. Paid more than I normally would and thought it would be worth the extra money. Not so.......As many others, it has a foul odor that will not go away and now sounds like a freight train in the house. Called Whirlpool about this issue and parts are not covered. Total cost of parts including the tool that is needed for this repair is $187.00 not including shipping. Whirlpool has lost my business moving forward as like many others, Im sure. Very disappointed!

Bought Cabrio 3 years ago, started getting ul code and f1 code. We leveled machine, but cycle kept getting stuck mid-cycle. Called repair guy, they say it is going to cost between 6 to 800.00 to fix???? Really. Its three bloody years old. Very disappointed. Do I now get it fixed or break down and buy another washer. I would not buy Whirlpool again. Very pissed.UPDATED ON 02/05/2015: We called an appliance repair company and initially paid $440.00. After installing a motherboard computer system, it still did not work. We were then told that the other part would be another $120.00. We were already soaked for $440.00 so we decided to pay. After that was repaired the washing machine was still stalling mid cycle. We were then told that it has something to do with the wiring and it would cost another $120.00-$140.00. Needless to say, we declined. Complained to whirlpool that machine was three years old. We are pissed and $570.00 out of pocket. Just bought a lg front loader and paid for a 5 year warranty!!

Have always bought Whirlpool appliances and never had a problem like this. Open the door on the top loading washer and its rusting out. I am having to buy a new one but considering other brands. No complaints about the matching Dryer.

We purchased a top of the line (we thought) Whirlpool stainless dishwasher 15 months ago from HHGregg. All was fine until 2 weeks ago - it produced a burning smell and was making a funny noise. We had it looked out. The motor is burning out. I called Whirlpool and explained the issue. There is nothing they can do. It is over 12 months. Really? They cant stand behind their product? I understand if it was a small part or such but an entire motor burning out in just over a year? I know that not all products can be perfect, some times mistakes slip through the line. I guess it was silly of me to expect a company in todays age to stand behind their name and product. Obviously, with this company, it is buyer beware.

I purchased the original Whirlpool water heater from Lowes in April 2008 for $372, and an installation charge of $443, grand total - $815. In February 2012 the tank leaked profusely, enough to ruin a section of hardwood floor in the room behind the garage where it was installed. Whirlpool provided me with return authorization, and Lowes provided me with a replacement water heater. So far so good. Since the original installation was done through Lowes, the replacement had to be as well, according to Whirlpool, but now they charged $500 with tax to install the replacement water heater! Grand total now is $1315. Fast forward to May, 2014 and the replacement water heater, just barely 2 years old, shuts off with a code of Bad gas control valve/thermostat. I call Whirlpool and an extremely rude 20-something staffer tells me the unit is out of warranty by one month! The replacement unit has no warranty at all - nada - only the original one does... Is this unbelievable or what?! BUT, they would be glad to send me the replacement of the defective part for $200 PLUS overnight shipping charges, and I would be responsible for all labor charges to install it. Had I opted for this my original $372 water heater would have wound up costing me in the neighborhood of $1800!! I told her in no uncertain terms what she could do with the repair part, and now I am going to go shopping for a water heater that will last me more than 2-4 years, and you can bet it wont be a Whirlpool, and it wont come from Lowes.

I owned a Kenmore washer for approx. 20 yrs that endured 6 kids for most of that time period. When time came for a new one, I had to have the latest model, and settled on a Maytag Bravos approx 3 yrs ago. This was a huge mistake - I paid between 600-800 for this machine, and it is a piece of garbage. The repairmen here yesterday explained to me that Maytag and Whirlpool are now the same company, and also that all these machines are now made overseas because of cheap labor. In a nutshell, I was given an estimate of at least 300 to repair this piece of crap - he explained that they are only made to last a few yrs -where is the justice in this situation? I really dont get how these big companies get away with selling crap, knowing all the while that the consumer is getting screwed - yet people continue to buy them..

Freezer froze up and water runs into refrigerator part. I am 80 years old and have never had any problems with any of my ref (except ice makers) before, but I have never owned a Whirlpool ref before. We have purchased Sears chest type deep freezers without any problems and have been very satisfied with freezers. This frig/freezer is a real bummer.