The inside glass of the oven door shattered. I have not used the oven for months. Only the the top cooking burners have been used. Its a mystery to me!! I have read complaints where the glass shattered while the oven was in use or being cleaned, but have found none where this happened to a cold oven. The large front burner is too hot. Even on the lowest setting everything burns. You cannot simmer, only boil. The control knobs have (in my opinion) no safety mechanism. I thought that the control knobs on stoves needed to be child proofed, hard for a child to turn on. My last stove you had to push down quite hard then turn to the setting. Not this stove. I have to be so careful when Im cleaning the area around the knobs. The slightest pressure and the knob turns. When I first purchased the stove while cleaning it, I unknowingly turned the knob and the kitchen filled with gas before I realized what had happened. I called Whirlpool thinking something was broken. They sent out a repairman. Nothing was broken. That is the way it is made. Customer Service said they had had no other complaints about the knobs. I find that hard to believe. My toddler grandchild can turn on the stove with ease. Im sure other concerned parents etc. have had this complaint. To sum it up... I will probably never purchase a Whirlpool product again.

Bearing on washer drum began getting louder at two years. Service man stated that Tide and a few other detergents were destroying the washer bearing seal. He told us that neither Tide nor Whirlpool will admit the problem exists. The cost of repairing the washer is close to the purchase price. Whirlpool should be subject to a class action lawsuit!

The Cabrio model (WTW5640XWO) I purchased in March 2011 died within days of installation. I was given instructions to modify the hose placement which resulted in a flooded basement and ruined carpet. Problems continued during the first year; several service calls. The problem was always the same; it did not drain/spin leaving a mess of soggy wet clothes. It died a final death - the same problem a few months after the 1-year warranty expired. The repair people have been out four times since. The last time, a $70 repair lasted less than 3 weeks for a bad shifter - always the same problem. Whirlpool will do nothing except offer to send a repair team out for a flat fee of an additional $120 with no guarantee they would fix the problem or replace the lemon. This week this Cabrio will be heading to the landfill. Ive had enough. No more Whirlpool products for me ever.

I bought it a year ago and the warranty is not even up and only in about a month the freezer door handle keeps falling off then the stainless steel which probably is fake is rusting too. They replace the handle and the door and the handle still keeps falling off and the doors are rusting again. My GE stainless steel dishwasher and stove are five years old and there is no rust on them. Whirlpool says it is cosmetic and that its not covered under the year warranty. I will never buy Whirlpool again. Awful customer service!

Im no longer buying Whirlpool products. They do not all up and are made like crap. My Cabrio washer being the most recent problem. Hinges broke on the lid and the drum spring broke. Out the door it goes! Im having my American made Speed Queen delivered tomorrow, the last Speed Queen I owned last over 30 years.

Recently, I was having a problem with my Whirlpool gas range so I contacted the 1-800 number. Long story short, the repair cost was so high I would be better off getting a new range. But believe me, it will not be a Whirlpool.

We purchased a Whirlpool Duet machine in September 2010. About a year ago, I started noticing tears and stains on clothing. Luckily, it was always on a washcloth or blanket, nothing special. Last week, it tore a 3-inch hole in my good jacket. I was not happy! My husband and I checked inside the drum and all around the seal. Neither of us found any rough edges. I thought if I called Whirlpool, they might have had a recall. They assured they had never heard of this problem. REALLY!!! Just look at all these e-mail complaints. Back to the old top loading - basic wash machine. Definitely not a Whirlpool!!!

We bought the Whirlpool Duet set for $1,000 18 months ago. About four months ago, it started shredding our clothes. I would get them out with holes in them, but there was nothing sharp in the washer. Then the grey outside seal started deteriorating and getting tiny balls of rubber all over my clothes, ruining several white shirts. It always smells like mold. I just went to get my clothes out of it to find out it leaked water all over with that disintegrated rubber from the seal. The seal had completely ripped from the top to the bottom drain for no apparent reason. Now we are replacing the below. We JUST paid it off this month. It is crazy, it is already breaking!

I have had my whirlpool oven for approximately 6 years. This will be the 3rd time I have had to replace the thermal fuse. For the last three times I have used the auto clean, it blows out the fuse. It has cost me $110.00 each time I called my appliance tech to replace the fuse.

One year to the day after the warranty expired, the meat drawer in the refrigerator began filling with water. Two repairmen have been to my home and cannot repair it due to a design flaw. Also, I had to pay for a cracked bottom tray that happened during delivery which I didnt know occurred at the time. Whirlpool is now ignoring my phone calls and emails. We paid in excess of $800 last year. What am I going to do now? Buy another refrigerator and get rid of this one? I dont make that kind of money and I feel Whirlpool should stand behind their products. This model is not even on the recall list so that means to me that other consumers buying this model are getting ripped off also. The customer service people say sorry but wont budge on reimbursement. I was told they cannot honor my request. Whether this was under warranty or not, it still cannot be fixed according to the repair tech that was at my home. I need to find someone to help me before this lemon I bought decides to burst into flames. I want a replacement refrigerator, not this model of course, of equal value. I am not asking for the moon, just for something that works beyond one year. In this economy, we cant afford to buy a major appliance after one year. My car is still running and I bought that in 1985. Please find someone to help me. I thank you for your time.

Cabrio fabric washer and dryer sucks. I gave almost $500 for a piece of **. Doesnt get the clothes clean. Hell most of them dont even get wet. Its junk. Wouldnt have another one. Lowes junk and the dryer aint know better. Its always flashing check lint even when its clean and you have to ** with it just to get it to start.

Do not ever buy a Whirlpool refrigerator. Sloppy construction, bins dont close, doors dont seal well and a brand new fridge doesnt cool to a safe food zone. When we call for service, I got the run around for almost 2 hours. They wont be sending anyone to service a brand new unit for an entire week... And thats 2 days before Thanksgiving! I have never had an appliance made this poorly. We dont have the space for a bigger unit, so thats why we bought this model. Size shouldnt impact quality!

I found this site while looking for a part number for the thermocouple. Lowes had one, but not for the FG model. I decided to call the number on here from Chris to see where I could buy the correct one with left-handed threads. I was told that they would sell me the conversion kit, but I couldnt get just the $8 thermocouple. Then $47.90 later and the conversion kit is on its way. Im not happy about it but at least I got 6 years out of my water heater before the thermocouple failed. The plus side is next time, I can get the $8 part from Lowes and not be without hot water for a week.

I bought my house brand new with all new Whirlpool Gold Series appliances. About a year and a half from purchase date, I started having issues with my fridge, then my dryer, then my washer, then my fridge again and that lasted about 5 months, then my microwave and my dishwasher. My microwave stopped working in January. It’s now April and I still do not have a new one. It keeps getting lost or shipped to the wrong address or something. Every time I call, the representatives don’t know how to look it up. I wind up on hold for at least 30 minutes, and I get transferred to at least 3 different people. I hope my last appliance doesnt break because I’m over Whirlpool, and I will never buy another appliance from them again.

Whirlpool Washing Cabrio machine model WTW5500XW0 - I purchased this machine five years ago. After about a year I started having problems where the clothes were not coming out clean. I contacted Whirlpool and was referred for a repair. The repair man told me these newer machines need the Affresh product to clean out the machine so this doesnt happen. I bought the Affresh product and there is still a problem. Every load of wash has to be put back in for another rinse cycle, sometimes two rinse cycles. Its ironic because the cover of the booklet for the machine says low-water washer which was the selling point to buying this machine. Instead of using less water, Im using DOUBLE the water.

We purchased our Duet in July 2010. It worked great until two weeks ago when the washer sounded like a 40-year-old washer. The bearing sounds like an extremely high-pitched “wrr”. We can hear it in the back of the house. I looked online to get parts and noticed that you cannot replace the bearing. You must replace the entire rear drum ($358.00). This does not include the labor. I talked with a technician, and they said the whole drum must be removed, not a one-man job, and to take the whole thing apart. Now, theres no price for installation. Lets go low ($200.00). Probably more. I cannot get a price nailed down without a visit. Now add those together ($558.00), I could put almost $600.00 into a washer that this could happen to in another 2 years. Wow.We had a washer that lasted us 15 years without any parts. Is there anything that you can do to help me? This is totally outrageous. Please help. Thank you. This was part of my chat to Whirlpool. Whirlpools response was I understand your problem but cannot help you. It is out of warranty. No help, no discount, nothing. I will and have all my friends never to purchase Whirlpool. This is from a so-called American company. Im very disappointed.

Although we live in Canada, we purchased our slide-in oven at Sears Roebuck in Buffalo, NY only because of the size availability only in the US (actually, the unit was manufactured in Canada as we found out later!). Obviously, this created another problem since the unit was not underwritten by Canadian Electric codes, Sears Canada repair would not touch it! Once installed, it worked great until the first problem with the oven quitting after self-cleaning. It is the second time in 3 years that both the thermostat and the sensor went in this RBS245 slide-in oven. Once the self-clean cycle completes (quite smelly!) and cools, the oven does not operate rendering the oven useless. First time, in 2009, Sears repair only suggested (since they would not do repair on it for reasons stated above) which parts could be faulty: Timer, sensor, thermostat or elements. It was thought to be the electronic timer unit, which was replaced at a $215 (needlessly) because that was OK. Both thermostat and sensor cost $150. Even the elements were replaced, $52. The second time, just a week ago, exactly the same happened. I replaced the 2 items: Sensor and thermostat at a cost of $154 and the oven worked fine again. I called both Whirlpool US and Canada, but no one could/would give any answers why this happens.So far, it cost $600 in parts to repair! This is nonsense from a company that has had good reputation and record. Obviously, that is changing! If Whirlpool cannot engineer a product that works as they say it does, they should close the shop! Reading here, there are others who complained with the same problem. It is time for Whirlpool to come clean!

As I write this, I am on my 5th service call in four months of ownership. The machine runs short cycles and requires us to not only do an extra rinse, each load requires an additional Quick Wash (with extra rinse) to get the detergent out. We use so little detergent that a 75 fl. oz. bottle has lasted four months with over 50% left. The techs Whirlpool sends are great. The call center first level people are fabulous. The supervisor is not helpful proclaiming that it was fixed. However, we still have to re-run the clothes every time.

We were a Whirlpool family, and have been using a Whirlpool front loader – Duet Steam Model # WFW9500TW - for the past nine years without any issues until recently when it started to vibrate. Technician sent by Whirlpool blamed it on failing bearing and that it was cheaper to replace than to repair (In hindsight, I wish we had tried repairing). Naturally, we decided to replace with a new front loader from Whirlpool - Model # WFW6620HW. Our previous version had a max spin speed of 1000 RPM and a capacity of 3.5 cu. ft. This new one has a top spin speed of 1160 RPM and a capacity of 4.5 cu. ft. The main problem with our old one was vibration, and this was being caused by the washer going into high spin while the clothes were not evenly distributed throughout the drum. In one spin, the clothes would spin perfectly without any vibration, but in another spin of the same cycle, the washer would not allocate that same clothes properly throughout the drum, which leads the drum to cause vibration from unbalanced high spin. Vibration is a problem, because like most Americans, we live in a wood frame house, and have a basement underneath with the washer located on the main floor. Vibration from unbalanced high RPM spin gets sent down to other areas of the house, causing damage, drywall cracks, separation in trims, etc. And these are all only the damages one can see with their eyes.One point about vibration and some myth busting. Provided that all your washer legs are meeting the floor and not on a saggy floor, your washer should not vibrate more than it does during an empty spin. If it does, then it is due to faulty, poor design/engineering. What happens is when the steel drum becomes unbalanced with laundry in high spin, it starts to shake as more of the weight is on one side, which one can notice looking inside the washer window. There are concrete weights fastened to the top and bottom of drum to keep the drum in place and to reduce its shaking tendencies. However, this weight also causes the washer cabinet to wobble if the drum itself is shaking. This wobble in turn causes the washer legs, which may be firmly grasping the floor, to very slightly come off the floor, which one can feel if touching both the washer feet and floor with their finger at the high spin of an unbalanced spin. And that motion of legs coming off the floor and hitting back at high RPM is what causes vibration to be felt on the floor and to be seen on the cabinet. Of course, this effect is amplified with washers that decide to go into an unbalanced spin with an even higher max spin. When our old washer perfectly balanced the clothes, it behaved like it was running high spin while the drum was empty. This is how all washers should behave, especially in America where the vast majority of homes are wood frame based. However, that was not what we experienced with this new Whirlpool. If a washer is not capable of balancing out the clothes, extra function or feature should be deployed in containing the drum shake to within the drum, and not allow it to escape.First, our old front load Duet Steam Whirlpool was Made in Germany. This new one is ‘assembled’ in America. The door window of the new one is plastic and feels cheap and flimsy, but I expect all the darker color door windows of newer front loaders to be plastic. Consider it cost cutting. We did not look for additional anti-vibration technology because our old Duet didn’t have anti-vibration features aside from its two springs and four suspensions. We decided not to use Load & Go because I have personally seen liquid HE detergents gum up over time, so I didn’t want to risk it gumming up inside the washer.After the installers left, I spend an hour cleaning the outside of the washer to perfection. Sadly, time wasted. Once I was done, I first did a wash without clothes, and then with clothes in Normal, fast spin cycle with drum about 2/3rds full. Just pants and t-shirts. There is a recirculating pump at the top of the drum to distribute the water, and to also distribute soap mixed water. But I am not sure if this is without problems. These pumps can collect soap residue with time, and you will eventually end up rinsing the laundry with soap mixed water even in rinse cycle.In getting to the first spin in wash cycle, I was flabbergasted to see how, just how rudimentary, I want to reiterate the word rudimentary, the load detection was before entering high spin. Our nine-year-old washer had a more comprehensive one. The new washer would spin the clothes at very, very low spin and simply see if the drum is most evenly spinning. That’s all. Compared it to our old washer which would also shake the drum to see if there was movement from side to side, because clothes can change their position when entering high spin. This rudimentary load detection causes the new washer to create an even worse uneven load distribution around the drum before spin, even though it may seem even at very low RPM. So, why is the new washer’s load detection so basic? I believe it is due to ball bearings.Front load washer models from other companies employ ball bearings to reduce vibrations from uneven loads. Whirlpool does not employ such feature, at least, they do not advertise them. However, to my surprise, I hear metal balls hitting each other every time the drum direction changes during the wash cycle. I inquired Whirlpool about this and I received contradictory responses. My theory is that the basic load detection before spin speed is used because Whirlpool assumes any changes to load distribution will be taken care of or reduced by the ball bearings of the washer. But this ultimately allows the washer to go into more uneven spins. The bearings may also be used to increase the tolerance of what is considered an ‘unbalanced load’ in order to get the washer to go into spin cycle faster, decreasing the time involved of the washer to go into spin cycle. Sadly, to my dismay, the new washer ended up causing a worse vibration than our old one with failing bearing.I called up the retailer the same day of delivery and complained of vibration. He first sent an installer to see if it was installed properly, and upon showing the installer of the vibration issues, the retailer sent me a new washer couple of days later thinking the first one was a lemon, and even though it has less noisy draining noise, it too exhibited the same issues with it going into significantly uneven spin. In the end, we decided to return the Whirlpool washer all together, at a loss of $200 because the retailer did not hold up to their spoken return policy.We have done many loads in this washer to see if our loading is an issue, loads of varying sizes, loads of varying types, loads of weights, and we maybe only had an evenly distributed load around the drum about once or twice. Once it was a King comforter. But, like our old washer, this too ended up not distributing properly around the drum in the final spin cycle and started vibrating, even though it was vibration-free in the previous high spin cycle. This proves that the problem exists directly within the washer, not the floor, leveling, load, etc.Some other problems with the washer: - The washer door, Load & Go dispenser at bottom, and single load dispenser at top are all plastic parts which all vibrate significantly during fast spin cycle. Especially the Load & Go dispenser which keeps hitting the cabinet to make banging noise. - Drain sounds are much, much louder than our previous Duet. It was even louder in the first one we received. Combine this to uneven spins and this washer can perhaps compete with an engine in terms of the sound it generates. - Single use dispenser at top left will hit the washer door if washer door is opened when the dispenser is also in open position. - Buttons are sometimes unresponsive, to which I have to power off and try again. But this has only happened a couple of times.- There is a small ¼ in. opening where the steel drum meets the rubber gasket, opening in which items like coins, etc., may fall through and are irretrievable. Don’t think small socks would be affected.To potential buyers, I suggest you proceed with caution when it comes to this washer. Understand the retailer’s appliance return policy and make sure it is shown in paper. It can save you a lot of headache. Get the extended warranty of three years because manufacturers only give you one-year warranty for a reason. I would also suggest that you avoid this washer at all costs if you have any floor level below where this washer is to be installed, especially if the level below is a basement. Your house is more important and more valuable than a $1000 washer.In the end, I am very disappointed in Whirlpool, an American company. Perhaps Whirlpool focuses their attention on top loaders, not front loaders. But Whirlpool had nine years to improve their washers, and it is sad that we may now have to go outside of America for a quality product to be used in American homes. P.S. No solicitation please, Whirlpool. This washer is in the process of being returned. P.S.S. I already posted this review in Whirlpools website, and it is under moderation.

For the last month, in order to wash dishes, we have to start the dishwasher normally. The water will begin to fill the tub and then stop and all the display lights go out. We push the cancel/drain button and the dishwasher empties the water in the tub. We again, push the desired wash cycle button just like the first time and the dishes wash normally. We have purchased at least two of this same type dishwasher with the utensil holder in the door from Whirlpool in the past, with great satisfaction.

We bought a gas hot water heater from Lowes on Dec. 31, 2010. In July 2011, there was no hot water. After much yelling and headaches, Whirlpool agreed to send out a technician to look at it, since I refuse to go in the attic and I will not work on gas appliances. After 7 days with no hot water, they replaced a valve that failed, they said, because our attic was too hot. The old unit never complained. Eight months later out, the unit went again (and we had an attic fan put in). This time, Whirlpool sent out a local plumber (and I paid for the call) though we had a warranty and extended plan with Lowes?! This time I was told no problem it was too windy and it blew out the pilot. Its funny we never noticed the attic being windy even during the hurricanes. Four to 5 months later, well, you guessed it but this time my husband just re-lit it. Then the next time, 5 months later, my brother-in-law did it. That was August to September 2012. See, this morning, there is no hot water. I had to fight with Lowes since we have the 5-year extended plan. I cannot get anyone to explain why it makes sense to them that a 2 1/2 year old hot water heater has to be re-lit every 4-6 months. Then I went online. Now I know why Lowes and Whirlpool are ignoring the issue. So, anyone know a good lawyer or what are they doing to get satisfaction?

I would like someone to explain to me why the control panel I.e. brains of the dishwasher which is around water is so sensitive to WATER. My daughter is the owner of the house and purchased this dishwasher last summer (2016) and within weeks we were having issue with the sensors. This supposedly was not covered under warranty (it was a WATER ISSUE). So now a dishwasher which cost over 700.00 is a door stop!! Where is people’s common sense... yes Im over 60 years old and very frustrated with the money that was spent for such an inferior product. Imagine having a dishwasher sensitive to water. The people who made it should give their heads a shake. Frustrated grandmother.

We had purchased an 80-gallon hot water heater less than five years ago. The tank started leaking, so the whole hot water heater had to be replaced. The previous unit we had was at least 10 years old, if not more. We are extremely displeased with the quality, and very upset with having to outlay such a large amount of money within five short years. Whirlpool has certainly not earned our trust in their workmanship.

In the last two years, the inner glass door of the oven has exploded. The last time was Tuesday, 14th January. The oven door was ajar because we had just finished cooking dinner. The noise was deafening but the worst thing about it was the large pieces of glass thrown all over the kitchen. Most of which were large enough and sharp enough to kill a child and seriously wound an adult. I phoned Whirlpool to report this. The operative I spoke to was very polite but told me these things happen and I could have banged it a while ago and left a weak spot! She also said a Supervisor or similar person would telephone me that day. It is now Saturday 18th January and NO phone call. MY concern is there is no mention of this being a possible problem in their literature and their obvious lack of concern under a Health and Safety situation. Not to mention the cost of replacement door glass.

This microwave has crack everywhere and its barely 3 months old. When I want to use it, it makes this weird noise and then it stops. I have not talked to Whirlpool yet, but Ill see what theyll say. My recommendation right now for all those individuals trying to purchase a microwave, dont even look at Whirlpool brand, they just ***.

I bought washing machine in March 2012. Since the date of purchase, the machine is not working properly. Even though it is under warranty period, I have to spend money on my own to repair it. Whirlpool customer care never responds. When I ask to give the number of higher authorities, customer care denies to do that.

What a horrible experience. I purchased a Whirlpool Duet HE Front Loading Steam Washer in 9/9. I have used it no more than 15 times. It has an error code F70. I called Whirlpool and used one of their recommended technicians. He was there for no more than five minutes and he informed me that it was one of the two parts--one is $300, the other is $500. Both these parts are computer chips. He instructed me to call Whirlpool stating that they would give me the parts for free. I did, and they refused stating that the product is now out of the one-year warranty. This is clearly defective. I am now faced with $1,000 fix. I feel that I was further misled by Whirlpool because they should have told me before the service call that I was going to have to pay $1,000. The customer service reps and the manager were both unresponsive and rude.

Our home is only 8 years old. Our neighbors and double ovens have all gone out! I mean it just quit working and the parts and repairs are crazy expensive! We have already spent $400 on a control board and now we need a control panel which is another $300! Its ridiculous spending $700 on repair of an oven that should have lasted a lot longer! Another thing is that our ovens are white and now the panels only come in black! I will never ever buy Whirlpool appliances again and I am spreading the word to everyone I know!

I have been buying refurbished appliances and this one we bought it brand new. Its a great buy and it will last a while. It does a good job washing and the clothes come clean and almost dry to the touch.

My wife and I have had a Whirlpool Gold 5.8 cu ft gas range for just 5 months and have already begun to have intermittent trouble with it. She can use the oven to bake cookies in the afternoon and then try to bake dinner a couple of hours later and the oven will not preheat no matter how long she waits!! This has happened three times now and we are waiting for a service technician to come out.. Pretty sad when you buy a top of the line appliance and begin to have trouble so soon.

Just bought two new Whirlpool water heaters, $469 each. Not impressed. One of the MANY issues: water leaking from the top. Reason: before installing, if you look inside female threads, you may see a rubber gasket (heat loss valve). One of the two heaters of mine was missing one. This showed me what the quality of the joint was like under the gasket. I temporarily removed the other three (two heaters) to confirm what I saw: At the backside of the threads there should be a clean flat landing from which to the male nipple should tighten against (washer in-between). Instead, there is a disaster of a flimsey lip (washer-like) which is torn up and not anything close to flush. Bad Whirlpool! Bad quality control!

The washer and dryer leaves the clothes heavy and wet, the balancing does not work, therefore the spin cycle just bangs against the machine, I tried emailing the support but no response, can somebody reach out.

This is my second Maytag French door refrigerator. 1st died after 5years. Bought the same again but bought an extended warranty. After 3 years, a month of service calls I still do not have a running refrigerator. Had to rent one from rent a center while Whirlpool sends more repairman. Try calling their customer service is where they got their name. They give you such a runaround they create a whirlpool. Product is junk.

My dishwasher quit drying and washing in hot water at Thanksgiving 2021. I could not get someone to look at it because the repair company (for Whirlpool) could not get to it until January 2022. The repair tech said it was it could be three different things. He was going to order all three parts. Three weeks later, they came to repair it. It still didn’t work and I hate to wait two different days (all day) for service. First day, he didn’t make it so had to schedule for next week. He replaced the other two parts. It now works by still doesn’t dry like it should. Not thrilled with performance at all!

My husband and I purchased a Whirlpool Washing Machine & Dryer a year and a half ago. As of current, the machine has stopped working. The machine will turn on but will not agitate. It makes a horrible grinding noise. The type of washer we purchased was a WTW4900BW0. Whirlpool told us we should have purchased the extended warranty. But, I feel we should get more than a year and a half out of a machine that cost $650.

Its supposed to be energy efficient yet it takes AT LEAST two times as long to get one load done, regardless of size or cycle preference! Now laundry takes all day! Literally! And why is there a lid lockout? Did someone accidentally fall in? If I drop something after Ive pushed start, I have to wait until the machine unlocks the lid. Why? This seems counterproductive. Its a top loader!

We have the same complaints about the washer as other reviewers -- have to use deep water wash to get enough water in the tub to clean and rinse soap from clothes and we have to keep the loads small. Dryer thermostat had to be replaced right off the bat. Now on medium heat it just burned patterns into two light-weight polyester fleece items -- the clothes came out with the heat input screen pattern burned into them. Now I wonder if they stuck to the heating screen for any length of time, was it a fire hazard? The burned parts of the items are now stuck to the drum so that needs cleaning. So well be using low heat on most everything and drying them twice, since low heat leaves them pretty wet after 35 minutes. So much for buying energy saving appliances which, by the way, we were proud to buy! But, prior to buying these appliances, we had washer and dryers that last 20 years. Built in obsolescence with these new things? I have no faith in the consumer complaint process anymore. The retailer may care as they are a bit closer to the problem, but the manufacturer? Forget it. Vote with your wallet and dont buy these products.

I purchased a Whirlpool stove, microwave and fridge in November 2012. The fridge model #WRT771RWYB01 has been a lemon from day 1. I have had the repairman out for the same issues multiple times. Ice build up in the freezer, water tube to the ice maker frozen, food in the fridge freezing, blah, blah. They have taped, glued, replaced everything they can and to no avail. It still happens. When you call for service, it takes 2 weeks or better to get someone out. I will NEVER buy another Whirlpool product! This has truly been a nightmare experience!

My old GE was better. I have to clean my Whirlpools filter once a month due to hard water - was wondering why my plastic cups had a white film - that was why. I have to put the knives and forks with the points facing up. My old dishwasher I could put the silverware in any way I wanted in the silverware compartment. My old one was quiet/my whirlpool I can hear it from the bedroom????

It was not a good experience after I purchased a Whirlpool washer in Feb 2014. I have been going to Laundromat 5 months since I found the door did not able to secure. I reported in January 2015 and technicians from 3 different contractors made more than 10 visits for checking and replacing parts. Not only nothing gets done, I also missed work for all these days. Then I escalated to the Supervisor, ** and Miss ** in Executive Office of North American Region. Both of them are very nice that they understand the situation and how frustrate it is. Finally, ** said Whirlpool would replace it. ** told me that I should get phone call from H.H. Gregg within 48 hours. However, it has been two weeks and seems no one care. In this three days memorial weekend, I still need to go to Laundromat while they are enjoying BBQ with their friends and families. I dont know how long it take to replace it.

I completely forgot that I wrote a review on our Whirlpool hot water heater model FG1H5040T3 Nov in 2010 until I received an email telling me how many people read my post. Surprise, Surprise guess what we are having problems with again. You know how nice it is to have hot water anytime you need or want it. Well, not at my house. The hot water heater worked for about a year (Im probably being nice with the time here). Heres our problem now, once the water heats up the pilot goes out. It will not stay on. Ive noticed that if its full the pilot light will not come on, so we have to run some water to be able to light it. Well I called customer service, a waste of time. The guy told me that my heaters warranty expired last year and his suggestion is to go buy another heater. REALLY! All I wanted to do was order a part for it. He did send me an article with suggestion of things to check. Sorry, we already did everything in the article, another waste of time. It seems we are not the only ones (model #) with problems with Whirlpool. Whirlpool used to make good products but its not anymore. I will NEVER buy another Whirlpool product again.

I have had this machine (Indesit IWDE126 Washer/Dryer) for a very short time; the washer is great. It does a 20 minute daily wash which is good however the dryer part screws up everything you put into it and ironing, even with steam, makes no difference at all. The WORST part is the organisation DONT CARE. I wrote to the Chief Executive, Jeff Fettig, who neither acknowledged my complaint or responded to it. I made this complaint in October 2016 and STILL do not know what the outcome is. If you are reading this review I honestly would look elsewhere for a better machine. Try MIELE. They are expensive but 2000% better.

We purchased the microwave. It looked nice and seemed sturdy. I bought a trim kit to make it look Built in. As soon as I finished installing the microwave and kit we tried to use it. My wife could not get the door to open unless she pushed the door button hard several times. I checked to see if the trim kit was causing the problem and it was not. We kept trying to get the door to open as it should but could not make it work correctly. I even used a little lubricant and it did not help. We then looked up the reviews and saw this was a prevalent problem. We then returned the unit and trim and ordered a Samsung. It will be in on the 25th of March. I placed a review on Lowes site but Whirlpool removed it saying since I took it back they removed the negative review. Since it was defective I wanted the public to see the truth on this unit.

Whirlpool gold series gas oven with Aqua Lift. Very unhappy with this oven. Cons: Aqua Lift technology doesnt work AT ALL (manual cleaning required); stove top hard to clean; 2 front gas burners are super burners which is fine for boiling water, but too hot for regular cooking. Would be better to have one super burner in the middle or back but two up front is way too hot for regular cooking, even on lowest setting; oven cuts out while cooking -- unexplainable how this happens but you really have to watch the oven while cooking to make sure its still on. Pros: large oven so you can cook ginormous turkeys or prime ribs.

I have owned a Whirlpool Gold Series Refrigerator for one year and 9 months. During that time I have had 7 repair issues. Each of the past ones took at least two weeks to repair. This past repair has to be redone because the new parts are also bad. The part is now on factory backorder. It will be at least two months for this to be repaired. Whirlpool says its too bad, we just have to deal with being without a working refrigerator for months. Do not buy this product!!! The warranty only means that you are forced to wait months for repairs. They will not replace, refund, or even extend the warranty for all this downtime. You have no recourse with the company.

Whirlpool Cabrio Washer WTW7340XW sounds like a small jet during spin cycle. The Whirlpool Cabrio Washers have a very well known and well documented problem with the tub bearings failing. Many many disgruntled owners have posted their complaints online, and there are many videos showing the issue on youtube. This issue is so prevalent that the manufacturer has created a tub bearing failure repair kit for $350. The repair is so expensive and labor intensive that many of the certified Whirlpool repair shops no longer work on the Cabrio washer stating that a better washer can be purchased for the cost of this repair.That said, the manufacturers customer service group denies that the Cabrio tub bearing failures is a common problem and are quick to state that Whirlpool holds no liability for this problem. Ramping the complaint up to a customer service supervisor is met with the same canned response. Regardless of the thousands of complaints Whirlpool is claiming that it is normal wear and tear for the tub bearings to fail. The manufacturer should recall the units for this manufacturing defect in the Cabrio design.

I just love the durability of my machine and the features that it offers. It does a great job washing my clothes and I feel like its a solid appliance that lasts for many years and its good quality for the price.

The Cabrio washing machine I was told by salesman best made so I spent big $$, makes sense right?! Wrong! During spin cycles sounds like jet plane taking off, was told barrings or drive shaft is at fault cause water seeping inside, causing rust, Whirlpool didn’t seal it or designed it to ensure no seepage. Never again Whirlpool. I’m done with your ineptitude, Type: 580. mod. WTW6500WW1. Set.# CY4970595.

Cabrio poor design - My number one issue with Cabrio is that it is destroying blue jeans. About 7-8 pairs now. It simply rips a hole in the leg. Also, sometimes clothes arent wet, usually not clean.

I purchased the washer and dryer set. My complaint is with the washing machine top loader that does not have the tall agitator not getting the clothing clean. All of my clothing come out of the dryer with dirty spots on them where they did not come out in the wash. Its a waste of water and energy because I have to wash them twice! I purchased the combo model numbers WED7300DWO and WTW7300DW0.

I purchased an expensive dishwasher made by Whirlpool and sold at Lowe’s. Immediately upon receiving the dishwasher I noticed a good size scratch. I had it serviced within one month of purchase because dishes were coming out dripping wet. Technician came out and told me I needed to add rinse aid. I had been using rinse aid, which I think is ridiculous to have to buy an additional bottle of something that’s not even cheap just so this thing dries dishes but moving on...Now it’s been 1.7 years and I’m having more problems. Top rack of dishwasher is broken and falls to the side every time you pull it out. The door to dishwasher also no longer has any spring. I take very good care of my things and this just unbelievable. I called Lowe’s they won’t help because it’s been more than a year! I guess Lowe’s can’t stand behind their merchandise for more than a year because they know they’re selling garbage. I called Whirlpool directly and was told they would come out and service my appliance for a minimum charge if $189! I have no words. I need to buy a stove in the next week and I assure you I will steer clear of Whirlpool. Like the title of my review I feel absolutely robbed.

I purchased Whirlpool gas range with AquaLift Self Cleaning Tech exactly a year ago. DOES NOT WORK!!! The only Self that cleans will be you on your hands and knees. Still dont know what to use. Manual says do not use oven cleaner or abrasive or you void the warranty. Ok Whirlpool any suggestions? Soap and mild detergent not cutting it. You would think with all the customers complaining about this feature the bright engineers that designed this would come up with a solution.

A total loss of money. Does not use enough water to clean clothes. Gets out of balance all the time. Do not buy.

5 years and 11 months ago I bought a 50 gallon gas, Whirlpool hot water heater with a 6-year warranty from Lowes. The 2007 water heaters were on sale, so I paid $329 for it. Within 6 months, I replaced the gas valve, and a few months after that, the thermo-couple went out and I replace that. Each time I called Whirlpool and got return authorization numbers for the parts, I still ended up paying for the parts plus labor. A year after that, the igniter went out and I had that replaced. Last year (the day before Thanksgiving), the thermo-couple went out again and I had to have that replaced - and it cost me for the part plus the labor - even though I had a return authorization number. I also replaced the water line connections/hoses to the water heater at that time. The customer service rep for Whirlpool told me at that time if I had another problem with the water heater, they would replace it for free - and the warranty was good until Dec 31, 2013 (this year). NOTE: Every plumber that has come out to fix the water heater and replace the parts stated that they see a myriad of problems with Whirlpool water heaters. They said the parts like the thermo-couples, igniters, gas valves, etc are poorly built and they replace them all the time. On Christmas Eve 2013 (two days ago), the water heater started leaking from the top by the valves - and so much pressure had built up in the heater the new water hose connections burst, spewing water all over the heater closet. I called Whirlpool the day after Christmas (today). At first, they told me they would not replace the heater as it was not in warranty and then I told them what I was told by the service rep last year. She finally agreed that my heater is indeed under warranty and gave me a replacement authorization number but she told me my warranty did not cover labor. I called Lowes. At first, they told me I would have to remove the old hot water heater myself and bring it back to the store in order to get my replacement. I am a 59 year old woman and I take care of my brother, a disable veteran. Although I am in good shape and healthy, I dont have anyone to help me get the gas and water disconnected and help me lift it into my Suburban. The man at Lowes agreed to bring out the the replacement heater and pick up the old one at no charge, but I will still have to pay $299 plus the cost of new hoses to have it installed. By the time the replacement one is installed, I will have paid a little over $1200 for a $329 water heater. I could have installed a tankless one for that, but I cannot see spending that kind of money right after Christmas. If I have one issue with this replacement, I will install a tankless water heater - and it will not be made by Whirlpool or any of its affiliates. My recommendation would be to steer clear of Whirlpool and their products.

Leaks water on bottom. Door seal dont go far to under door, is from manufacturing defect, is water overflow or is something else. Dishes washer is about 10 years older. Very real disappointed and wont buy this brand again on dishwashers.

We have had Whirlpool front loading washers for 15 years. The first had a bad bearing problem, that was eventually fixed, but still disappointing. The second doesnt is missing some features that the old one had. All and all I am happy with this washers and do not know of anything better, within my price range.

I bought a full kitchen appliance package 3 years ago, the gas range Clock LED started cutting off the line at the top of the numbers... when the range was about 1 1/2 old... Now 3 years later the range doesnt hold its oven temperature, the cost to fix it is $230 more than what I paid for the range. Whirlpool is unwilling to stand behind their product or provide a replacement part for a reasonable price. So now I will be buying a brand new range and the 3 year old Whirlpool will be taken to the dump. I will never buy a whirlpool appliance again. I thought Whirlpool was a good brand and a reputable company until now. Please beware when buying appliances, whirlpool is not reliable or reputable.

Whirlpool Cabrio top load washer: nice job Whirlpool! You designed a washer that breaks if you accidentally wash a coin! For the second time in a few months, were fixing our washer because a coin was in a pocket. The coin gets sucked into the discharge pump and sounds like popcorn popping when it drains. It rattles around the inside of the machine’s pump until it breaks the plastic pump housing. You will know when this happens because there will be water on your floor. Did you ever consider a screen to prevent a coin from ruining the washer? God forbid someone leaves a coin in their pocket. Well, if you leave a coin in your pocket and wash your jeans, it will cost you a repair every time with this hunk of junk. This would be my last Whirlpool. It will actually be cheaper to throw this thing out and buy a new one, since it won’t be the last time a coin accidentally makes it into the washer.

I have a Whirlpool refrigerator model number wrx735sdhz and its been a lemon since I bought it. The ice machine totally backs up and the Chute overflows and Im always scooping ice out. Had another technician out today. He saw my frozen sour cream download Frozen pickles and everything else Frozen. Then because I had to have the ice maker replaced in March and it did nothing for the unit he reports back to A Plus Appliance that theres nothing to be done and he says his diagnostic tests come back that it is fine. Im going to post a very negative review about them. Lowes told me that if he would have reported differently they would have given me a voucher and refunded my money. So have another Appliance repairman come in tomorrow.I bought the extended warranty and so far its gotten me nowhere. As many times as Ive had to unclog it and throw away food I could have had technicians out here hundreds of times for this defective refrigerator. Plus on the two service calls I had they said that there has been numerous complaints about this model and the ice maker and freezing over. I have thrown thousands of dollars of food away over the last 2 years. Lowes extended warranty has got me nowhere.

The first Front load Whirlpool washer leaked. 5 repair techs visits. Wasted days. Finally located the leak, in the main basket. Replaced washer. Second washer the clothes come out smelling like a horse blanket. Mold. Clean the washer every month still mold. Plan on junking the washer a getting a new model. Never expected this much trouble and time on a basic appliance.

Whirlpool Gas Range WFG540H0es - Purchased 2 months ago. After 2 weeks there was a spill. The black burner caps are powder coated. After cooling we washed it with dish detergent & a sponge. The powder coating came off. Called the company. They replaced burner caps. Last week there was a spill and it stained the burner bases which are powder coated in a silver color. We tried 409 cleaner, Windex, dish detergent with a sponge. Could NOT get the stain out started removing powder coating. Called the company they ONLY guarantee cosmetic appearance 30 days. They wanted $139.00 for a new set of burner bases. I am going to go back to Lowes & see if we can return this Whirlpool range.

The pilot of my Whirlpool hot water heater (model FG1H5040T3NOV) suddenly went out and I called in a plumber to check it out. He managed to restart the pilot and we had hot water again, but it went out again within 12 hours. He mentioned that I would most likely need a part called a thermo coupling and I should start looking for it. Well, I found this site and read one of the positive reviews that provided the WP toll free number, so I called. Talk about great customer service! Ben was amazing – he took down all my info and was very helpful. Even though the warranty expired years ago, he overnighted me the replacement parts I needed at no charge. And there’s no charge for shipping either! My plumber is completely anti-Whirlpool HWHs and now he will change his mind when I tell him how efficient they are. I also hope he doesnt charge me a bundle to install the replacement part.

We purchased a Cabrio washer in August 2013, in early August 2014 we noticed that it was not getting all of the detergent out of the clothes (noticed it on the dark clothes after drying). We use less than the recommended amount of HE detergent and dilute it in the dispenser, also always use the extra rinse. We just had a Sears service man out at a $100 cost only to find out that he gets these calls all of the time and the machine is operating at the factory settings.After reporting the problem to Whirlpool all I got was we are sorry and a link to how to operate the washer. In the demonstration video it clearly shows that the water level never covers the clothes. I know Im old school but in my opinion the water should cover the clothes so it can properly wet and agitate the items in the washer. To say I am less than satisfied is a gross understatement. Im out the cost of the washer plus an additional $100 and after a year of ownership and contacting Whirlpool less than a week after the factory warranty ran out all I get is an Im sorry you do not know how to operate a washer.

Our $2000+ Whirlpool Gold just had the control board fail. After calling Whirlpool, local services and all national parts suppliers we were told each time the part is on back order until June. If this is Whirlpools way of generating new fridge sales, it does not work. No Whirlpool, Kenmore, Frigidaire or KitchenAid, all made by the same company will ever enter my home. The control board runs the fridge. Which executive thinks a family can live without a fridge for 4 months? What terrible service. GE always has parts and service. Go with GE everyone.

I bought a semi automatic washing machine from Croma Store (Gurgaon) on 03/09/12 Model no A-72H* and I regret to say that the water direction changing knob (to change water flow from agitator to dryer), has broken. The machine is not even 4 months old and the water inlet is broken. How can this happen in a brand new washing machine? You claim to have durable home appliances products and your machine does not last 6 months? Can you see that the broken piece is attended to or replaced at the earliest?

Whirlpool Water Heater Purchased at Lowes - Like all the others I see on here. I Purchased a Whirlpool water heater at Lowes Model# BFG1H4040T3NOV. Pilot will not stay lit; customer service tells me to replace the thermocouple which did not solve my problem. This is the second time in 2 years same problem. First time it was fixed under warranty but now since it was replaced once it is not eligible for replacement so I now must decide if I want to pay someone to figure out the problem and I must pay to repair it or what I am starting to think is that I will likely junk it and buy a quality unit and be done with the games and run around and just have hot water, which is all I really want. I will never buy another Whirlpool product in my life and will encourage everyone I know to do the same.

7 months ago we had a Whirlpool dishwasher installed into our home. While away on vacation the piece inside malfunctioned and caused major damage as water filled the home. Whirlpool claims, that because it’s a part that they contract out to another company, they “Whirlpool” are not responsible! If you purchase a product from Whirlpool and they put their name on that product, then Whirlpool should stand by its product. Well... beware, you’re not going to compensate from Whirlpool! We urge you, make sure of whom the parts of the product your buying from belong to, before you buy it FIRST! Never again!

We have been very satisfied with the way our dishwasher has performed over the years. It cleans the dishes well. It runs somewhat quietly. It doesnt seem to use too much detergent to get the dishes clean.

Whirlpool Cabrio Washer WTW7800XW2 - After buying my American made washer..... at nearly $900 with extended warranty about 2 years ago. This week noticed small cracks in plastic that surrounds and holds glass lid. Now lid will not sit flat and glass is emerging from encasement. Called extended warranty claim center and was told it was a cosmetic issue. Called Whirlpool, and was told they were unaware of this flaw, even though countless websites, chat sites, and Youtube. My frustration is how they claim to be unaware of this flaw and refusal address it, after countless consumers have called. I would be willing to start a class action on this matter!

My complaint is basically the same as all the others. Clothes do not come clean in my brand new Whirlpool washer. Ive had two other Whirlpools, and they were fine. This one, however, is a piece of junk. One of the main problems is that the washer is designed to use only lukewarm water, even on the hot setting, it does not use hot water. Another problem is too little water. Another irritating factor is the constant locking of the lid. Another problem is the constant starting and stopping of the agitator. This cannot be good for the motor. Im at the point of giving away my new washer which Ive had for exactly one week. This is a totally inferior product, and I feel that I have been really ripped off.

My wife and I purchased a Cabrio washing machine and dryer, this is by far the worst washing machine we’ve ever owned. It hardly fills, even in deep water cycle. If you watch the clothes through the smoked glass lid with a flashlight, you can see they don’t even go underwater. The dryer seems to be fine but I would never recommend the washing machine to anybody looking to buy one.

Mind you, Whirlpool products that we have purchased in the past have been satisfactory, but gas hot water heaters, no! About four years ago we purchased a Whirlpool hot water heater that went out in a little over a year. After spending many calls and time, we found out that the HWH was on soft recall. Whirlpool credited our account, but this was to purchase another Whirlpool, which we did. We paid for installation. About 2 years later, it has gone out. Same problem. Lowes says not their problem. Whirlpool says it will pay for the part only. Plumber will cost 150-200 dollars. All the plumbers I have talked to will not repair them, then they are held responsible when it goes out! As a disabled Vet I cannot afford to throw 400-600 dollars away. And, Whirlpool tells me that if they give me an RA number to replace the HWH, it will have to be a Whirlpool from Lowes. Great! Whirlpool quarterly report looks very good. Mine doesnt look as good. What can be done about a poor working product? Or is this too big to fail? Let me know.

It will constantly go off balance. I usually have to wash the cloths twice before they come clean and I have to unload washer and re-load it to get it to possibly spin without going off balance again. It will twist the quilts and fold them under themselves and tear them from the pressure. I have called after 6 months of owning this product and explained to the Lowe’s employee and they said it cannot be returned unless it was broken mechanically. This is the worst piece of crap I have ever own. The last Whirlpool product lasted 12 to 20 years. I hated this thing after the first few washings. I generally have to stop the washer and let it soak and then turn it back on if I want the damn thing to get the dirt out. I am using the required detergent as well. I will never own another top load machine like this. I am trying to unload it. Now, I have to buy another washer because I might as well take the clothes out and beat them on a rock at a creek with this thing.

We bought a Whirlpool side by side refrigerator in September 2009 for $898, which was a lot then. Last fall the ice maker jammed and started dumping ice in the floor. Yesterday, we noticed that things in the freezer werent solid. After checking, we found our frozen food had thawed and things in our fridge werent very cold either. We called Whirlpool which was no help. Then we called a repair man who told us, “There was a leak in the seal system and it was low on freon. Would have to replace a compressor, evaporator and it would be better and cheaper to just buy a new refrigerator. It has just turned 4 years old. I called Whirlpool again and they said they didnt know why it went bad. I said is it a recall or just a bad refrigerator. The girl was no help at all; I kept asking to talk to a tech and finally asked for their corporate office address which she said was 553 Benson Rd., Benson Harbor, Mich. 49022. I now have to buy a new refrigerator and it will not be a Whirlpool.

I purchased the Whirlpool Cabrio, Model no. WTW5640XW2, on March 3, 2012. I have tried every setting and water temperature and am totally dissatisfied with the washer. It does not clean clothes, tangles them into a twisted mess which requires that they be vigorously shaken out, destroys anything with a draw string. I had an online chat with a representative and was told she was sorry. I posted to Facebook and did receive a call from a repairman, which I will return; however, I do not anticipate receiving any satisfaction. The machine is worthless for washing clothes. I was better off with my 12-year old agitator Whirlpool washer. I do not understand how this machine can be allowed to stay on the market. Id be better off at the river beating my clothes against rocks. I hope someone will get on Whirlpool to give consumer refunds. I have been brought to tears by this machine and I am one tough cookie. Please help!

I purchased this washer about 3 years ago to replace a dishwasher which lasted 20 years. Within a year the racks began to rot, the front panel plastic started to peel off. Within two years half of the racks rods completely rotted away. 3 years later the washer is busted - most likely pump which was probably blocked by one of the pieces of the rack rods. I am replacing it with Bosch - German engineering. Needless to say I will NEVER buy a Whirlpool - formerly reputable company again. Good-riddance Whirlpool.

Whirlpool Cabrio WTW7340XW washer is a piece of junk! I have had issues since the day I bought it and havent even had some of the failed parts that other people are talking about. It does not save water. I went from 5000 gal to 13000 gal in one month! It doesnt wash clothes. Everything comes out with the same spots they went in with and then some. Light colors come out with what looks like grease spots and whites come out with black spots. I have had it five months and have used six of the monthly cleaning tabs. Clothes get tangled and torn because of the speed of the spin cycle even on delicate. This unit needs to be recalled and redesigned or customers should be offered a different washer of their choice within the price range of this unit.

Aqualift technology does not work!! This is absolutely the worst product I have purchased from Whirlpool. The aqualift technology DOES not clean the oven, even if you clean the oven after EACH time you use it! I am not able to bend over and spend the afternoon in the oven. And even when I do, I cannot get this oven clean!!! Please DO NOT buy a Whirlpool stove with an aqualift technology oven cleaning process!!! You WILL be sorry!!!

I purchased the Whirlpool Cabrio washer in 2011. It has been nothing but trouble since. I have had repair people out here several times, because the machine twists and tangles the clothes, doesnt get the clothes clean. Sometimes the clothes come out dry without even getting them wet. There are lots of soap scum too. I would NEVER buy another one of these. SO DISAPPOINTED.

Problematic... constantly out of balance... and will Not spin out due to this.. Sensors are very sensitive... have to unload and reload.. Most times have to wring out by hand.. Definitely a defect of these machines.

We had Lowes install a Whirlpool model Nu40T121-403 natural gas water heater early October 2012. The temp controller went out in October of 2014. I replaced the controller myself at a cost of $30 for overnight UPS from the manufacturer, American Water Heater. The controller went out again almost exactly one year later and I again replaced it for the $30 shipping charge. In both instances the customer service person told me the malfunction was probably due to my not flushing the heater annually, causing a sediment buildup. The water to the heater not only flushed annually, but is filtered through a water softener and there was absolutely no evidence of sediment in the drain water or on the part of the control that is in the tank. Now it has stopped working a third time. I called Lowes about replacing it, but they only carry Whirlpool, so wont be buying a replacement from them.

Three failures in 14 months. First, the detergent dispenser broke. Next, right after the warranty would have been over (fortunately, I purchased from Costco which automatically extends warranty for another year) the pump failed and had to be replaced. Now the heat element is obviously faulty because the dishes are cold through all cycles. So I have to call them back again. I have no complaints about the service company. They were polite and reasonably prompt. Just appears that the product is JUNK! I am going to Costco tomo and will explain the situation. They probably can’t do anything but maybe they will go to a better product for others.

Water heater purchased in 2011 and is already broken. Called the hotline and they were rude. Told me I need a $199 part. I read all the reviews and it seems that Whirlpool has made a bad name for themselves with the water heaters. They were not willing to work with me.

We have had a Whirlpool dishwasher for about 2.5 years and have been happy with how it cleans dishes. About a year ago we replaced our counter top and in the process had to adjust the bend in the mountain brackets that attach the dishwasher to the underside of the counter. This requires flexing the thin piece of aluminum at the perforated line. In the process, one of the brackets snapped. The other was barely still intact and broke several months later. I tried jerry-rigging them, but eventually decided to replace them and called Whirlpool customer service to ask for replacement parts.Unfortunately, Whirlpool wanted to charge me $10.50 apiece and another $9.00 for shipping and handling. These parts could not cost more than a few cents apiece. I was shocked that they would charge me $30.00 to replace these flawed parts. Never have I had such and experience with any customer service department. The three people I spoke with were all rude and unapologetic about my situation. Two blamed it on the install...Ive installed plenty of dishwashers and never had any problems in the past. Even if it was a failure on my behalf, the simple replacement of the parts for a reasonable charge would have been fine by me. I told them Id be happy to pay a few dollars and to pay the full shipping fee (which was also high, in my opinion), but they refused to meet me halfway. I can only think that this is part of their business plan...make dishwashers with sub-par parts, and then over charge for the replacement parts when they fail. Well, I re-upped my jerry-rigging efforts and have improved the engineering of the faulty part. Save my $30. But Whirlpool will never again get my business and Ill be sure to steer clients and friends away from this brand as well.

There is a melted hole in my Whirlpool microwave. The model WMH53520CS is on the recall list for this but not my serial number. Other have posted this and theirs was not covered. This should never happen. I have never had a microwave do this. If I have to replace it I won’t buy Whirlpool ever again.

I have never posted a negative product review but must do so now. The refrigerator is 1 1/2 years old at most and has been well taken care of. I noticed today that the finish at either side of the bottom of each refrigerator door handle has a problem. I couldnt tell if the finish was pitting or is just discolored. I called customer service and expected that they would help, especially since we have an extended warranty. Representative number one told me that the extended warranty only covers problems that affect the function of the product. I spoke to her supervisor and then her supervisor. I got plenty of apologies but no support. I offered to send pictures, but they were not even interested in checking out the problem.After speaking to them, I took the handle off and I see now that the handle cut into some sort of film that exists on the metal. (I am not talking about the protective plastic coating that is on the the refrigerator at delivery.) The film is lifting off the surface and creating discoloration. If Whirlpool was at all concerned, I think this issue could be fixed with some sort of gasket to keep the metal handle from cutting into the surface. Im hoping the problem is static, but hard to say what will happen. If they had been interested in trying to understand the cause of the problem, it would have been easier to accept the limitations of the warranty. It would have demonstrated an interest in avoiding this problem for other consumers in the future. My last Whirlpool product. Period. Good luck if you decide to do business with them.

Refrigerator, less than one year old, quit working and destroyed several hundreds of dollars worth of food. Whirlpool warranty division was notified and a service technician was scheduled to arrive yesterday, a week after the warranty division was notified. Yesterday, no one arrived. Today the warranty division was again notified and we were advised the service technician was never scheduled and they do not know why this happened. Here we sit again for another four days awaiting a service technician.I am disgusted with the failures of Whirlpool and their warranty division. Again, in less than a year Ive paid nearly three thousand dollars for a refrigerator and it fails, destroying hundreds of dollars of food. This has been a complete struggle trying to maintain food in a household both children. I expected a long time manufacturer to provide better warranty, service, and not just tell me they are not sure why. I would hope that no one ever buys their products again, God knows I will not!

We saw water all over my wood floor and traced it to the lower freezer unit of my 15-month old refrigerator/freezer. We had to call a repairman which traced the problem to a frozen defrost. He put in a new thermometer at the tune of $200 and now we have to deal with a wood floor problem on top of it. I purchased because Whirlpool was always known to be a quality product. I wont make that mistake again.

I bought this washer because we are a family of 6 that washed a lot of laundry. I bought the extended warranty from Lowes but not sure if this thing can even be fixed. The guy has been out twice. Replaced the control panel. I cannot wash more than 3 towels or it comes unbalanced and goes crazy. I need this fixed. I am so irritated. A recall needs to happen.

Bought a Whirlpool dishwasher and just over a year later all the wheels fell off the bottom rack. Called to get replacements and it was going to cost me over $200. I paid $800 for the whole machine. I would NOT recommend Whirlpool. I have now heard of other people having the same issue. Very disappointed. Will probably buy a new dishwasher as it will probably happen again with the replacement wheels.

This washer was purchased on 12/21/2007. It was in a vacation home that was rarely occupied, therefore washer not used much. On 7/23/2008 the cycle switch was replaced. On 7/20/09 the same problem occurred. The washer may have been used 5 times during the year. The handle and rim also needed to be replaced. On 8/31/09 the switch and handle were replaced again. On 2/5/13 the door latch was BROKEN AGAIN. Now on 7/10/15 the door latch, start switch and cycle switch are broken again... DO not buy WHIRLPOOL products.

Our daughter has a Whirlpool Duet front loader washer & dryer combination which is less than 3 years old. The washer shows fault code 71 and will not run or release the door lock. The first repairman said the interface board and/or a computer will need to be replaced. Cost is $600 to $1,000. I called Whirlpool. They recommended their trained tech be called out. He looked at the broken machine and determined the interface board was bad, and he put a temporary repair on the washer and said Its okay to use for now. He will return in 2 weeks with the replacement part. We tried the machine with a load of clothes. The machine filled up with water then quit, and the door was locked. We called to get a tech to open the door so we could retrieve our clothes. No one is available for 1 1/2 week. I called Whirlpool and was told a claim form would be mailed to me so we could be compensated for the damaged clothes. The letter arrived. I was appalled when I read it. First, it came from their Legal dept. The intent was to scare us into getting a lawyer or just use our homeowners insurance for the damaged clothes claim. I called Whirlpool back several times and was told too bad, so sad. Whirlpool might make a good machine; they cant prove it by me but their support rates a big zero.

I bought it 1 week 1/2 ago and cannot wash correctly the clothes in it, have to rewash 2 or 3 times and bedding? Forget it. Still is dirty. Water does not go over the clothes, it suck for the price I paid.

I bought a whirlpool cabrio with high hopes. Unfortunately, it has been the worst washing machine I have ever had. Then I moved in with my fiance and he too had a cabrio. It too is a piece of junk - and brand new! Every load comes out with left over residue and the clothes look worse than before they went in! I have tried everything and I do mean everything! IM 41 y.o. - IM well aware of how to load a machine. I load it just the way the instructions say: as if there was an agitator there. Ive tried using no laundry detergent or fabric softener - clothes still come out disgusting. Ive made sure the screens are clean, doing extra small loads, turning on the extra rinse, everything! Ive called whirlpool, but there is no such thing as customer service anymore. They just blamed me for not loading the clothes properly and blew me off. The machine becomes unbalanced very easily (it is leveled on the floor), sometimes the clothes are still soaking wet at the end of the cycle and sometimes all knotted up. This is a horrible machine!! I wish I could say it makes me feel better that IM, by far, not the only one having issues with this piece of junk!

Never ever plan to buy a Whirlpool product. I took the washing machine in December 2008. System was not got at first time also. I called service center, and he came and asked to put this and that. Again, it got a problem. This time, he told me to change powder. I was shocked how a powder became a problem for its failure in washing clothes. Next, he told me to put a stand. After a long interval of 6 to 7 months, I got fed up and called him again. He told me it was not in the warranty. Its the worst service. Zero percent satisfaction Hats off to Whirlpool service. Please, friends, never buy cheap Whirlpool products.

We have had the Whirlpool Cabrio washer and dryer for 4 years now. Let me start off by saying the first 6 months was wonderful. Then after that, the machines were breaking down every time we turned around at the worst times. With 2 adults and 4 children, you see my point. We have had a repairman at our house to fix these machines 6 times and now, we are getting a code on our washer that is F1. Looking up codes online shows to be the computer system of the machine and a $400-$600 repair, might I add. Please save your money and buy a better and more dependable set than Whirlpool. Washers and dryers used to last 20-25 years, or so my parents and grandparents did. All of the manufacturers are building cheap junk so we can buy them more often.

We purchased our unit (Microwave Hood Combination #WMH53520AH-1) in Fall of 2013 and within a year we noticed there were occasionally problems with the sensors; occasionally when you would open the door the lights would flicker and even rarer still, they wouldnt turn on at all. Id close and re-open the door several times to try to get it to register, because if it doesnt you are unable to heat anything in it. The sensor issue increased with the passage of time, but because it was outside of the 1 year warranty, Whirlpool refused to do anything about it, instead advising that I pay $70-140 for a service professional to come out and inspect it. The biggest problem with the sensor issue in this unit is that normally, if you open the door mid-heating cycle, the microwave will automatically turn off but once I opened the door AND IT CONTINUED TO EMIT MICROWAVES - the cycle stayed on!!!Needless to say, on the occasion that the microwave is actually working and we are heating something up in it, we NEVER open the door mid cycle and instead hit the cancel button, which blessedly works. You would think Whirlpool would care about their reputation for making high-quality electrical products. A flaw in the construction or design of a product can appear if quality of materials is poor and the problem can be exacerbated over time. Which is why I assume the warranty is only for one year. High Quality Products and Good Customer Service are such rare things these days. For our next microwave (which I imagine well need soon) I think well forego Whirlpool and go with a different company.

I purchased a front loading Whirlpool washing machine March 2017. I have need to have the drain pump replaced and the motherboard replaced. Each repair took 30 to 45 days to get parts and service. I would not recommend the washing machine.

We have a small space that fit a washing machine and figured we could add a dryer on top but didn't have an outside vent, so took a chance in this model. It fit perfectly in the space and saves us from a regular trip to the laundromat. It takes a bit longer to dry but is energy efficient.

I would give no stars for this piece of junk, Whirlpools energy efficient top load washer. I called 1 day after their warranty was up. It was actually purchased on Oct. 9th, 2010. The machine was leaving spots on my clothes from day one (was told it was my detergent)! The machine started making strange noises and not cleaning clothes. It was coming out worse than they went in the machine! I called on Oct. 10th, 2011 to complain. They told me my warranty was up! I had to pay $234.83 to order F7E1 activator and pay repair. The repairman told me that my machine was not delivered until Oct. 14th, 2010. It should have been covered on warranty!