Surprised my daughter with a Whirlpool washer and dryer computerized, never again you have to stand at the washer half the time resetting it over and over. It takes all day to wash. Went to Lowes. They said yes you have to start it three times. What a pain. Never will buy one again.

Dont buy. Purchased over the range microwave. Service order less than a week after install. Heats unevenly. Burns center of bacon consistently without fully cooking ends. Popcorn pops half the kernels yet Whirlpool says nothing wrong with product. Well within 1 year warranty but had to pay for service call cause Whirlpool determined microwave was operating as manufactured. Laughable! This company does not stand behind their product or their customers. Never again will I purchase a Whirlpool product.

It was obviously designed by someone who has never had to clean a refrigerator. There are grooves in the door gaskets seemingly making their sole purpose to collect crumbs and mold with no obvious way to keep them clean (No, Q-tips dont do it). A layer of ice forms below the basket in the freezer (bottom freezer) which, when it melts, soaks the kitchen floor. Ice must be chipped out at least every two weeks to avoid flooding.

Installed in May 2007, paid $674 for GU2455XTSS1 Whirlpool Dishwasher. It required service in March 2009 for $158 It became noisy in Oct 2011, so I placed a service call for $136. It was very noisy in Jan 2012. Again, I placed service call for an additional $93 that Whirlpool has not reimbursed. I must now replace the motor quoted at $403. The motor has a 90-day warranty. The 4.5 year old dishwasher must now be replaced. Whirlpool has not responded to email and to registered letter requesting a cost-effective solution to repair dishwasher that recognizes that reasonable life of the unit should be 10+ years and not 4.5 years.

I just bought a house with a Whirlpool Accubake wall oven and after I did a self-clean, the oven quit working. It goes through the motions of working but neither element heats up. After replacing the elements ($95), I am going to replace the thermal fuse to see if that cures the problem. Whirlpools automated Customer Service phone service sucks. You cant talk to anyone about troubleshooting any problems so you spend money until you eliminate all possibilities.

Replaced the “brain” twice. No hot water for 2-4 days each time, waiting for part to arrive. Now I have to replace the nylon drain valve because it won’t shut off. Gonna use brass replacement. Fortunately I have it drain to a sump pump so house isn’t flooding. Don’t buy Whirlpool water heater from Lowe’s unless you enjoy this kind of thing. Consolation: the folks at the help line always answer the phone and are knowledgeable. And they’ve heard these same complaints over and over. One guy even said to buy AO Smith as they are made in Tennessee instead of China.

Purchased Whirlpool refrigerator model #WRF532SMBM & a new dryer on 11/14/15 from Community Appliance in Middletown, NJ. Waited 3 wks for delivery. Worst purchase ever! Very cheaply made. There is a 1 space between shelf edge & walls all the way around. Put a lb. of butter on shelf & it fell down to the bottom. There is no butter keeper which allows orders to be absorbed by open butter. No egg keeper. In the freezer, the bins are wire baskets. So far I have dropped a bag of frozen blueberries & they fell to the bottom of the freezer. In French door bottom freezers it is almost impossible to retrieve items falling through. Ice packs fall through, very poorly designed. Very loud, supposed to have a water filter in upper right corner for easy access... its not there!Called Whirlpool, waited 20 min. & all the rep could say was, So sorry youre not happy. Asked if modifications could be purchased or made... nope. Asked to speak to quality control, a supervisor, anyone that may be able to give some satisfaction. Nope. She was making notes of all my complaints so they can be passed on to engineers for future models!!! Had a rebate offer, rep transferred me to that dept... cant/ wont honor it because 1 day too late. KitchenAid, Whirlpool doesnt care once they have your $. NEVER again. Ill shop Kenmore products from now on.

Bought fridge in 2010, I am about to replace the icemaker for the 2nd time at a cost of over $300 each time by a Whirlpool authorized repair tech. No kids in the house and very limited use of icemaker. Motor keeps burning out because of the design flaw per the tech. Very poor design for a $1,500 fridge. Due to these issues I do not intend on purchasing Whirlpool products in the future.

Im glad to see that Im not the only one that is dissatisfied with Whirlpools products. Three weeks ago I found my basement to be flooded and you could tell that it was from the hot water heater that was installed in 2005. The plumber changed the release valve. I thought that was it. This past Wednesday I go down the basement and find another flood. The plumber said pilot was not lit. The explanation was wind could have come down the chimney and blew out the pilot. Pilot was relighted and within 12 hours there’s cold water again. I called the plumber again and said that the thermal coupling must have gone bad. I went to Lowe’s to get a replacement and found that Whirlpool is sending a free replacement but I would have to pay shipping. All well and good, but what do I do in the meantime for hot water? If Whirlpool made a mistake, why didnt they send the replacement parts to the businesses that sell their products? I guess that would be the simple solution; instead, they expect me to pay $30.00 for shipping and be without hot water. Well, let me tell you: Im tired of this hot water heater. Whirlpool can go out of business for all I care because they dont stand behind their products. Im going to buy myself a Rheem and Im sure Ill be a lot happier. Need a new hot water heater? Don’t get a Whirlpool!

We have always bought whirlpool appliances, and trusted the name. We can put a man on the moon but we cant build a reliable bottom freezer refrigerator. My previous refrigerator was whirlpool. 19 yrs old when it went out for a new whirlpool bottom freezer fridge, 2014 Jan. 14 months after purchase, no warranty. The temp in freezer and upper compartment would increase and stop making ice. At first, we thought it was the icemaker. Repairman NOT FACTORY TRAINED, THIS IS VERY IMPORTANT.. Came and looked at it said, yep, icemaker. Plugged it in after 4 days. Just like brand new - making ice, not the icemaker. About 4 days later same problem - temp increasing. Called the store where we purchased it, sent the same repairman. He said it was a cooling fan. This went on for 2 months trying to figure the problem. Well, we cant rebuild a refrigerator out of parts it doesnt need, so we called a FACTORY TRAINED TECH who diagnosed the thermostat and defroster in the bottom of fridge taking two screws out and pulling bottom freezer out. It was iced up. Cost to fix it - 522.00. So I called whirlpool corp., explained problem. They agreed to pay for parts if we paid labor, 100.00. This is doable. However, if we continue to have problems after this, we will purchase a top freezer fridge, no ice maker because they constantly break down.

My boyfriend and I purchase a Whirlpool Cabrio Washer and Dryer on November 28, 2010 from Lowes in Shepherdsville, KY. Just after we purchased the set, I read some bad online reviews of the set. I called Lowes and talked to Chris ** in appliances and he assured me that this was a good set and that it was very popular with their customers. He assured me that if there were any problems that Lowes would make sure they did everything they could to fix and/or replace the appliance(s). My intention was to cancel the order when I called, but he convinced me not to, now I completely regret not canceling that order that day.In May of 2011 we called Lowes to report that the dryer was not working properly; they sent a repair person from Maytag Service Co, 1500 South Shelby, Louisville, KY 40217, phone number 502-637-6526. The name on the card that the repair person left is Steve **. The repair tech indicated that the problem was that the belt had come off and he put the belt back on the dryer. It has worked without issue until about 2 weeks ago, when it stopped drying again. I assume the belt is off again since it is performing exactly the same as it did in May when we had the repair company out.I called Maytag Service Co approximately 1 to 1 1/2 weeks ago to see when a tech could come back out and I was told they only work Monday - Friday. I told them both my boyfriend and I work and cant really take time off from work to be home for the repair. The male on the phone indicated that they could call 30 minutes before arriving if that would help. I told them that wouldnt really help since I work in Louisville (about 30 minutes from Shepherdsville where we live). He indicated that was the best they could do.Yesterday, November 7th sometime during business hours. I spoke with someone in their appliance department. He indicated that I would need to call Maytag Service Co at 502-637-6526. I called them and was advised that they could come out the next day (today), November 8th, but they could not give me a time window. I spoke to a female who did not identify herself. She specifically stated, If someone has not called you by 8:30 a.m., you can call us and we will give you a time window. Since I had just earned a vacation day at work, I so desperately need my dryer working that I took the day off to get the dryer fixed. I got up at 7:30 a.m. this morning to prepare for the service call. I have not left the house today. At 9:20 a.m. my boyfriend called and said that the service company had called and they were not coming out. I called them back and again spoke to an unidentified female. She indicated that they called my boyfriends phone at 9:00 a.m., he called them back at 9:20 a.m. I was on the phone with the female at 9:25 a.m. She indicated that I should have called at 8:30 a.m. and that they never call their customers because they dont have time to call them all. She said that when my boyfriend didnt answer the phone at 9:00 a.m., they had to send their tech on to the next call because, they cant have their tech waiting around 20 - 30 minutes on customers to answer their phone. When I told her that I took my only vacation day to be home for this call, she indicated that I would have to reschedule for another day because their tech was already on his way to another city. I then stated that I thought that was ** and she hung up on me.I called and spoke with the store manager at Lowes in Shepherdsville, KY. He called Maytag Service Co and was told that I used profanity and was rude and that I would not provide them with an alternate number. Most if not all of these are lies. I did say **, but I was not rude and I was never asked for an alternate number. I give out my number and my boyfriends number to almost any company we deal with. My boyfriend is also a service technician for Icee Corporation and he is not allowed to be on a cell phone in his work truck; therefore I always give both numbers since I can easily answer the phone throughout the day. The store manager made several attempts to try to find another company to come out and service our dryer, but cannot find anyone to come before tomorrow. Since I used my only vacation day today, I cannot be here for the technician and my boyfriend doesnt have any vacation or sick time to take to be home for the call.I cannot believe that after spending over $1300 on a Whirlpool Washer and Dryer set (including several hundred dollars for the extended warranty), that we cannot get our dryer serviced at our convenience. Since when did companies only repair or back up their products at their convenience? This in my opinion is the worst customer service I have ever seen. I thought Whirlpool/Maytag was a good company; now Im not so sure. I just wish I could return the set and do more research and find a quality appliance that wont break down 2 times in less than a year!!

3 months after I got the fridge, the ice maker went out. 3 months later it started to work again. Replace the water filters 2 times per yr. It is noisy when it makes ice.

I have tried to contact Whirlpool, email and telephone call. Finally someone called me but Customer Service was poor. I asked her to have a Manager call me, but she never did. They also never responded to my email. We Purchased our new Refrigerator 21 c.f. side by side 2 months ago. The ice maker is driving us crazy. It is very loud. There are white plugs on the 2 bottom corners that make the appliance look extremely cheap. I am not happy with this Refrigerator!

I had water heater EE3Z50RD0550V installed on 11/3/11 and it started leaking July 29, 2013. Whirlpool gave me Return authorization # and said I have to return the water heater to Lowes (purchase place and original installer) to get a new one. Fortunately, Lowes said I only have to bring them the RA # and they will swap out the water heater. However, there is a $300 charge for installation. Whirlpool says they only cover this the 1st year, except when its a manufacturer defect. But they cant tell me how to prove its a manufacturer defect. Why else would a glass lined water heater start leaking only 21 months after installation?

I waited years to buy this machine. I hate it!!! I agree with the other bad reviews. It destroys clothes. There is barely enough water in it to cover the bottom of the machine much less the laundry. Even deep water is a joke. It does not clean. I put it on the hottest water temp and I can put my hand in there and it is barely warm (it is not my hot water heater). My lightweight comforters come out all tacky and grungy in the middle. The softener dispenser (I use vinegar) dumps in the laundry (no it is not over full) (no I do not slam it shut). I can not let anything soak because the machine will drain after a few minutes and all my detergent, scent crystals etc. are all wasted. I feel like I have to take a survey and complete a questionnaire every time I do laundry. Can someone tell me how to put a comforter in there and leave that little middle eye open? They say the water saver is government regulated? Yup I need the government to do my laundry... I believe in saving water. I have a water saver toilet, shower, faucets. However I can not clean dirty jeans in a gallon of water. My clothes do not even get wet. How does whirlpool get away with advertising this machine can do king size comforter? The gentle cycle will tear apart anything I might put in there because there is no water and that blooming thing just twist and turns so it tears anything delicate. This is the 21st century. I think I should not have to babysit my washing machine. Why should I have to readjust everything in hopes it might be almost clean??? Place this here and that there, wipe the lint out before doing dark laundry. This machine belongs in the dark ages. It is so complicated yet it achieves nothing. A big rip off. I so tired of crying over this purchase. I hate this machine!!!

All of these awful reviews and you continue to sell the Made in China JUNK!!! And shame on the stores that advertise and sell Whirlpool JUNK!! They should put a warning on these machines stating Will not last, gets off balance and does not clean your clothes. Yes we bought the Cabrio like the others, our clothes would not get clean, because like sheets, would end up looking like a doughnut without a hole and all of the dirty water would drain through the middle and make a spot. Then you have to wash them over and over. But that is not the worse part! It only lasted 13 months, YES I said 13 months just past the warranty LOL!!When the man came to make repairs, it was the gear box and was going to cost almost $600. Almost as much as we paid for the machine. He recommended getting a Speed Queen, we did and I LOVE it!! I think it is the BEST MACHINE I have ever had. They are a little hard to find though, but I found where they were sold on the internet and the dealer had to order it. Well worth the time and trouble, (trouble) which I dont expect to have with this machine. Like I said it is a wonderful beast. And I will never buy another product made by Whirlpool. Before my husband retired he made prototypes for autos so he knows about testing and Whirlpool had to know this product had bad flaws before they put it on the market, I call that fraud. Bad taste in my wallet, Michigan.

I bought a Whirlpool refrigerator water filter from the Marcone distributor. This distributor, whose name I received from calling the 800 number in your manual, did not send instructions on installation. I called Whirlpool and they did not have instructions on installation. The product is 4392949. In talking with your customer service department filters, I learned that the young man knew nothing about filters. He told me that the filter that I purchased was the wrong one. Its interesting that he tried to convince me without knowing my refrigerator model number. I asked if he wanted the model number and he said, yes, please. It was very sad how I had to do a song and dance with an idiot. I had no help from your company. I will return this water filter because I was not provided instructions for installation. Neither can your people produce them. For this reason, I will never purchase Whirlpool again.

We purchased our first front-loader washing machine (Whirlpool Duet WFW9250WW00) just over two years ago. Since we purchased it, it has torn clothes and we have replaced the drum baffles twice (this would be the third time, but we are throwing the washer out), the drum seals twice (another place clothes can get caught). I had adjusted my washing (maybe I overfilled the washer, maybe I was using the wrong spinning speed), but every so often clothing would come out with holes or torn. The drum baffles must come loose before they come out, and clothing can get caught underneath them (I think that is where the tears occur). It has happened at least once a month and I had spent a fair amount of time trying to figure out where the clothes got caught and torn. Many people complain about bad smells from the washers (which I never had - I like the Tide with Febreeze detergent and every so often clean it with bleach or Affresh), but never torn clothing. I would really like to use a front-loading washing machine, but we are going back to the top loader - we cannot afford the clothing tears. I have seen that many people replace baffles (not many speak of clothing tears) and maybe in the future this problem will be addressed. But in the meantime, I would stay away from Whirlpool front-end washers. (GE makes some nice top loaders - and in 40 years of washing clothes and only owning two other washers, I have always thought washers to be an appliance that would last 15 years or longer with very little maintenance or trouble). I believe that I really tried to make this washing machine work out, but it got to the point where my husband did not want to wash baseball uniforms and other irreplaceable clothing in our washer.

I have been a dedicated Whirlpool customer for 50 years. I purchased my new, Cabrio washer and dryer in 2011. The dryer works fine. The washer does not. It ties everything in knots. Most everything comes out in one large, wrinkled lump. When washing sheets, it wraps the whole load in a soaking wet, fitted sheet bubble. You cannot wash one item by itself, because it will become unbalanced and shutdown. I will say that I havent had any repairs yet, but I have a feeling, its only a matter of time. I have decided to buy a new washer, but it will not be a Whirlpool.

I have Whirlpool Washing Machine bought at end of 2012. In 2014, I faced an issue where the washing machine board ics are gone. The services people came and check the replaced a board. It was cost me 6000 Rupees including the service cost. Very next year 2015, again the same issue. Board of the washing machine gone. Now I have to change the board. It seems it may cost more than previous one.I heard that these service engineers are taking the previous my board / replaced board. They are repairing it and sold it again and again so the quality of the board is question mark. As a customer I / we cannot spend money and change board every year. I just want everyone to think twice before you go to Whirlpool Washing Machine & its products. I had a same kind of poor quality issue with even water purifier too. Consequences - I have spent Rs. 10000 already, it is loss for me beside the buying cost of the products.

WTW4950XW2 - I purchased My whirlpool washing machine wtw4950xw2 from best buy in 03/30 2013 and it just stop working after 3 yrs. The manufacture warranty was only good for 1 year. I think companies does that on purpose because they know these new equipments are not going to last. I think before they use to have at least a 3 yr or better warranty on appliances. First it started making this loud sound when on the spin cycle, so I had a repair guy come out. He told me that the bearings needed replaced so (how does bearings goes out in 3 yrs). I asked how much will it be to replace parts/labor. The Parts cost $250 and the labor is $200. I might as well buy a new washing machine. I am so disgusted with this machine. My previous Whirlpool, which was not the new modernized, I had for at least 12 years and also I bought a whirlpool dryer. My Dryer stills works after 15 yrs. Im going to try to hold on to the dryer until the long haul. I wish I just would have gotten my old washing machine fixed. Now Im looking for a new washer and I wont be doing a whirlpool or anything with a push to start - just a plain old agitator, no sensing mechanism, just basic.

My Whirlpool dishwasher is 11 years old and has performed satisfactorily throughout. The utensil container is in the door, saving room inside but making it a bit less convenient to remove. The results are satisfactory, but I carefully rinse everything before putting it in the dishwasher. I dont believe dishes with hardened food would come out clean without this step.

The washer and dryer leaves the clothes heavy and wet, the balancing does not work, therefore the spin cycle just bangs against the machine, I tried emailing the support but no response, can somebody reach out.

Our dishwasher stopped working after 13 months. We are a family of 2 and use it once a week. We called Whirlpool and were told since it is past 12 months, they would do nothing but give us the name of a repairman in the area. We called our own repairman and $120 later, the sensor that had malfunctioned was replaced. Quite costly on a $450 dishwasher. Now, after 15 months, the handle on the lower broiler portion of my Range has come off and the screws will not hold because the plastic around them deteriorated. I just called customer service once again, knowing what I would be told and YES was told So sorry, nothing we can do. A new handle will be $45 plus shipping. We bought the refrigerator at that same time and every day, I wait for this appliance to have issues. In summary, Whirlpool/Maytag appliances are obviously made to be disposable after 12 months. They do not stand behind their products and I would not recommend them to anyone.

High end Whirlpool dual front loader washing machine model number WFW94HEXW2 died after 5+ years of less than moderate use. Used no more than once a week. Paid for a top end model. Had 2 mechanics look at it. Mechanically it is fine. The CCU is not working correctly and wont allow it to start. We replaced it, but to no avail. It is barely out of warranty at 5+ years old. Called Whirlpool and they said they would do nothing. Asked for a manager and she was rude to add insult to injury. Cant get to the serial number because the door is locked shut as part of the shutdown problem. Cant find original receipt so including a picture of the credit card purchase. Trying to contact retailer but so far have not heard back from them.

On May 25, 2008, I bought a Whirpool Model# BFG1J4040T3NOV 40 gallon natural gas hot water tank. The pilot light went out today, Sept. 26, 2011, and it will not re-light. This was bought at Lowes and was rated as a 12-year warranty on the tank and parts. This is premature failure of a product that is listed as 12 years. Due to all the other similar complaints of this Whirlpool hot water tank, I would like my money back ($455.81) plus installation or a new tank installed.

The buttons that turns on the burners and oven turn on with a very light touch and start leaking gas and sometimes light. Its very dangerous and has done this since We got it new from Lowes. I wonder if there was a recall on this model or if lots of other customers have had the same trouble. Model #WFG524SLAS O Ser. # R20910336 We have had this stove about two years and My wife has kept after Me to report it , but I never realized how dangerous it really was until now. The previous stove We had you had to push in on the buttons and then turn them before they would light. Thank You.

We purchased this washer on 2008-04-27. It ran okay until a few months ago when it began making strange intermittent noises. This is now happening more and more often. I reviewed a lot of websites and see that this is a common occurrence for Whirlpool Cabrio washers, and Whirlpool will not stand behind it and make it right. Im going to write them a letter mirroring what Im saying here, and remind them that other appliances in my house are coming due for replacements or upgrades. Whirlpool and its affiliates will not be part of those upgrades going forward. I have no patience or tolerance for expensive **, which is what they put out here. I will have to purchase a replacement washer since this seems to have two major areas of failure, both extremely expensive to repair. I might check out Roper and see what they have--its apparently very well rated by the folks that work on these things.

We purchased a high end KitchenAid Refrigerator Dec 2018. Rust developed on water dispenser door in less than year. They would not honor warranty. Since March we have had ongoing cooling problems with 5 service calls and 4 different fixes and unit still doesnt work. Local authorized service company, Fields, in Jacksonville FL is incompetent. Whirlpool doesnt return calls. The products value is not consistent with the high cost. Here are the gory details. Ref: Setzers, Jacksonville FL (sold unit). Fields Jacksonville FL (factory authorized service company).Less than 1 year in, it began to rust. We called for a Warranty check. Fields Appliance (their factory authorized service company) came out and agreed all 5 doors needed to be replaced. A month rocked on, finally we called to find out where the doors were, and were told Whirlpool (Makers of Kitchenaid) denied the claim. Citing that we lived near the coast! Well, our other appliances arent rusting and the refrigerator doesnt sit outside! They sent us a 6 oz bottle of rust cleaner. A few months later, this refrigerator stops cooling! This was in March, 3 months out of 1 yr warranty. The refrigerant system is warranted for 5 yrs. This was also right at the beginning of Covid 19 shutdown. Fields could not give us a appointment, due to shutdowns. So, I called a local company to fix it out of pocket. He discovered a leak in the coolant lines, fixed the leak and replaced the coolant ($453.61 on 4/9/20). Great, it works! About 3 weeks later, it stops cooling again. Called local service repairman out once more to see whats going on. He replaces a thermal bi metal sensor and well ahh! It works again ($100 on 4/28/2020).About 3 weeks after that, it stops working again! We are thinking by now, its a problem for Setzers, Whirlpool, and Fields. We call the local service repairman out to confirm and he states that the evaporator fan motor will need to be replaced, and that part replaces all sensors as well ($59.99 5/28/2020 service call). We call Setzers and schedule an appointment with Fields. First appointment we could get was 6/16/2020. Guy comes out, and cited a factory defect, per a technical bulletin he had, and relocated a sensor. Simple as that, he assured us it was fixed! Even though I pointed out it felt no cooler when he packed his things to leave. It did nothing! In the background Setzers (when they would call back) were supposedly working with Whirlpool to help fix the problem! Whirlpools reply was that since our repairman was not factory authorized, it completely voided our warranty! Explaining we had no choice, since Fields wouldnt come out and by now we are without a working refrigerator for 3 months, they could care less! Feeling totally frustrated, we call Fields again! On 6/19/2020, they send out another repairman. This guy came in, opened up the back, and immediately stated the refrigerant was overfilled. Didnt do any diagnostics, just told us that we were **, and walked away, without even putting the refrigerator back in place! Neither Fields rep hooked up a diagnostic tool to confirm any real issue, I guess they just knew! Total incompetence! So... As of now we have paid the local repairman ($448.33 on 6/26/2020) to order the evaporation fan motor and install it this coming Monday (7/20/2020). Total amount out of pocket at this point, $1053.90. It took that long to get here! Wish us luck! Setzers wiped their hands clean of the issue and told us to call Whirlpool. We did have not ever received callback.

Brought brand new. Had for ten years. Still going strong. Matter of fact all appliances are Whirlpool. Dishwasher, stove top, oven. I like the sharp clean look in my kitchen. Easy to clean!!

We bought a new Whirlpool Dishwasher. Installed it, wife used it for two loads. The third time she tried using it the door sprung and it no longer latches. After two weeks of calling Whirlpool, we finally had someone come out to fix it. After the repairman took a hammer to the frame he stated that it had been dropped. He wobbled the dishwasher back and forth with his hand. He said the frame will never be correctable and we will always have problems. After another week we got a hold of Whirlpool and were told the repairman has ordered parts to repair the dishwasher. Whirlpool is hoping it will hang together until the warranty expires. If the dishwasher were fixable that would be fine. However, when the repairman who has years of experience in his job tells me it will never be right and will always be a problem, I believe him.

Absolute garbage!!! French door refrig/bottom freezer. Too much to go into. This is by far the worst product that I have EVER purchased in my life. If I was strong enough to lift this piece of ** over my head I would carry it into the corporate headquarters of these money grabbing dirt balls and throw it through the CEOs door. Amend that: I would locate customer service and consider them bowling pins. What a bummer; how far we have fallen!!!

I recently purchased a new Whirlpool propane water heater. Dependable name, dependable product, years of trusted service, right?! We have bought many Whirlpool products over the years but never again. Got it home and installed it. It sounded like a plane taking off, and that was in the garage. Next came the lack of hot water. Mind you, we replaced a 40-gallon tank with a 40-gallon tank and the last one we had lasted 18 years without a problem.Well, same showers as usual, and we were turning up the heat mid-shower and again and again during the shower. Even turning up the heat on the water heater didnt relieve the problem. We are not happy with the product. And, no, there is nothing mechanically wrong with it; its just sub-par. Our water heater from 18 years ago worked more efficiently than this newer model. We called customer service, and we were told that unless there was something mechanically wrong with it, such as a defect, there was nothing we could do. There’s simply no recourse.Shame on Whirlpool for not making a quality product and standing behind it. This was a very expensive purchase - over $500.00. We thought we were buying a quality appliance. Very disappointed, and I will be returning it. I’m never buying another Whirlpool product again. I can only hope that the company we bought it from has a better customer service policy. Very frustrated and disappointed.

I purchased a Whirlpool® 4.5 cu. ft. Front Load Washer with Load & Go Dispenser in 2017. By August of 2020 the washing machine was no longer working. The machine would continue to fill with water and not shut off. The machine would then give an error of E01 and F03 and drain all water within 5 minutes of the wash load starting. I had a certified Whirlpool technician come and diagnose the problem for $99. The technician said these error codes happen ALL THE TIME on Whirlpool washers. The technician tried to replace the water pressure switch with no success. He then spoke to a corporate office and was told we would have to replace the motherboard for over $500. The total cost for the diagnosis and repair was almost the exact price I paid for a new washer just 3 years earlier. I will NEVER purchase any Whirlpool appliance ever again.

This washer is only a year old and out of warranty. At first I was getting white stains on dark clothes and now I am getting unremovable oil stains on all of my clothes. With the white stains I cut back on dry detergent and went to liquid. It did not help. On black stains I sorted clothes very carefully so that nothing dark or black was in with other color or white clothes, still the same stains. Brand new capri pants ruined with first washing. I have tried cleaning the machine with bleach as recommended, did not work. Whirlpool and Sears deny they have ever had a complaint. Yet there are hundreds of the same complaints on the internet. Is there anything that can be done.

I purchase a suite of Whirlpool Kitchen Appliances April 2017. My range is the slide in model. The knobs are on the front of the stove top. I 4 months in I saw that the paint behind the plastic panel where the knobs are was chipping. Also, the gasket in the oven had some loose threads so I finally decided to call the warranty. Whirlpool paid for the gasket to be replaced but Customer service said the chipping was cosmetic and that only covered for 30 days. I am so disappointed in this range and Whirlpool. My stove looks very used after 10 months. I followed the instructions on what to clean it with and how to clean so I know its not me. The paint chipping is crazy! How as consumers do we deal with this? This Range was a cost over $2000! and they give me touch-up paint!I purchased Whirlpool because I researched prior to purchasing my appliances. I thought I was buying Quality, this is not quality! At Christmas I had a pot of potatoes boil over and the element circle on the glass top cam off with cleaning. This too is not covered because its cosmetic. Ironically, my old glass top Whirlpool range did the same thing. That why I got a new one! I guess it still works. Who cares how it looks... RIGHT? Well, I WAS a good Whirlpool customer. Not anymore! Do not purchase Whirlpool glass top ranges unless you want it to look worn out after less than one year. I have tried to post pictures but this wont let me paste them!

I purchased Whirlpool Washer WTW4815EW on December 29, 2015 for my tenants apartment and by October 7, 2016 it was not working. I called Whirlpool for service since the product is under warranty. The closest appointment was more than 2 weeks out. On the appointment date the technician called me and said he was on his way to my house which is more than 30 miles from my tenants apartment. The technician said he could not service the tenant area as that was a different group, so we rescheduled for a week later. A week later no one shows up, so I rescheduled yet again for November 3rd and drove myself to wait for the service person who was supposed to be there between 8 am to 12 PM. At 11:40 I saw there was a 10:36 am Whirlpool attempt to call me but no message was left. When I called back they told me the technician called in sick and they called at 7:30 (my iPhone indicated 10:36 am). Now they say someone will come on Saturday November 5th. It will be one month on November 8th with no working washer. While it is bad enough the washer stopped working in less than one year their service support is even worse than the product.

I purchased this Refrigerator Model #wrb322dmb, bottom freezer, 21cu ft. last year on July 3, 2015. In September I noticed rust spots on the top door. I called Home Depot where I purchased and they directed me to Whirlpool. I did purchase an extended warranty with Home Depot. Whirlpool did replace the top door. Thought that took care of it. Today one year and two weeks out of warranty, I again notice rust on both doors. Called Whirlpool. They said too bad out of warranty, not considering I had a previous report of this very same issue. So since I am very unsatisfied with this result and the fact that an expensive product is rusting, I decided to share to try to prevent someone getting stuck. Stainless steel is not supposed to rust which leads me to believe that it is not Stainless steel, but a Stainless Steel finish and not a very good one. So I am stuck with a rusting $1200.00 refrigerator only after one year. I have always purchased Whirlpool, but no more. They lost a 40-year customer. I have always bought American made but no wonder people are not buying American made any longer. TO SUM IT UP WHIRLPOOL STAINLESS STEEL APPLIANCES RUST! DO NOT BUY!

The Cabriolet washer and dryer act funny. I really believe its because they are digital... Didnt they realize that at some point moisture would affect controls? Idiots! And if a cycle is stuck, you cant manually move it forward or backward... you know, how the standard machine works... yeah the one with knobs!! Sometimes computers are not necessary and this is one of them... too damn advanced!! Id rather have a good old American washer. Not worth it. I get a better wash at the laundromat. # pissed.

I have spent 30 minutes trying to change light bulb under the oven and get the cover plate back on. I watched the film on how to do it, it was amusing to watch the struggle to get it on. It was amusing to say the least. Whirlpool watching it??? I do not believe whoever designed this worthless time consuming light cover never tested it one time, or it would had been more user friendly. It amazes me what kind of trash they can build for us consumers to have to deal with at times. Tomorrow this overhead piece of junk is coming out and being replaced by a non Whirlpool one. I am going to get a tractor and smash it into little pieces and put on side of street with a note saying this is what happens when you try for an hour to change the bulb.

I bought a Whirlpool Cabrio 2 years ago and until last week it was fine. We got an error message that said we had to call for service so we called a local whirlpool repairman. The repair guy told us it was the control panel and it was going to cost between $400 to $500. He also said that he works on a lot of whirlpool washers and this is the first time he saw a machines control panel fail. He recommended that we call Whirlpool.I called Whirlpool customer service and after waiting on the phone for 40 minutes I was quickly transferred to customer resolution and was told that since I hadnt purchased the extended warranty there was nothing that they could do for me. I kept asking her, There is nothing that you can do to help me? And the consistent answer was no. I will never buy another Whirlpool appliance. This has been so frustrating to have an appliance that looks brand new and wont work. The manufacturer wont even try to help with fixing the problem. Amazing AWFUL CUSTOMER SERVICE.

Bought a nice house in 2012 which has a Quiet Partner 3 Dishwasher. About twice a week it has to be reset pressing buttons because it blinks at you when you press start. Control board was replaced a couple times since we bought house. We just put up with it. The tub has a manufacturers defect in bottom where the plastic is so thin it finally cracked and over time water trickling out went to wall. Then ruined an area in finished basement ceiling. Ive used a couple different things to stop the leak but it always starts leaking. Customer service says its not under warranty so will buy a new dishwasher. But not Whirlpool or Maytag. Same company now. Dishwasher is a total piece of crap.

The pilot light went out on our Whirlpool hot water heater. We followed instructions and were unable to relight. Our plumber was also unable to relight so we ordered new parts with associated overnight express costs. The plumber returned and worked for over an hour. When the pilot light came on the burner assembly burned out the new thermo coupling and that needed to be replaced again. This happened again. I would like to join the class action suit as Whirlpool has known about this problem and consumers are paying more than the original cost of the unit for repairs.

Purchased the fridge from hhregg in August/September 2012. Model G16FARXX. After less than three years of owning it, found out today that the compressor is shot and will have to be replaced. Replacement/repair costs are ~$900, almost as much as the fridge brand new. Chatted with customer support and then would/could not do anything. I feel ripped off. If it happened after 5 years of use, then my attitude would be different, but not a major component going out in less than 3 years.

I have bought two Whirlpool water heaters and with each one have had the same problem: the pilot light will not stay on. I have to continually turn the pilot light on each day. I have replaced the entire flame/pilot/thermal couple assembly several times. Each time I use the unit, it works for about 2 weeks, then Im back to turning on the pilot light every day. Im convinced that there is an inherent design flaw that Whirlpool should be forced to deal with. It seems that this should be a fraud case to sell a known, documented, defective product. Shame on you Whirlpool! Its obvious that its all about the money! Band all Whirlpool water heater products!

I’ve had the dishwasher for at least 3 yrs. if not longer. I have a long history with Whirlpool products and so far I haven’t had any problems with my past purchases. They normally wear out from age because if you take care of it normally they last for years.

I have a double door refrigerator with a bottom freezer. It is slightly over 2 years old and has been in use for only 7 months of that time. We just got off the phone with Whirlpool service. They will cover the cost of the control panel and defrost control. The other one I paid to replace was only one month old and it failed again. In the time between that I had to have an Icing kit put in as the Ice maker was causing ice to form inside the back wall of the refrigerator. My first call to Whirlpool was very unsatisfactory. I ended up paying for the part and the service call. The second call was about the ice-maker and they were aware of the problem and sent me a repair kit for the problem. I still had to pay for repair service. So far I have paid $561.62 for their defective parts and service calls. This time my wife called (while I was taking my frozen foods to my neighbors freezer for the second time) and went through 3 people before being told the part was still under warranty and they will send a new one. When we pushed for proper service we got it. We should never have had to go through all this. We also lost over $300.00 of frozen foods. Never buy a Whirlpool refrigerator!!!

I have had my Cabrio set for two years only and the washer has a error code of F6 and E3... pretty much does not work properly and need to swap out main control board which is about 200-300 for the part. I’m very disappointed in this product for as much I have spent on it. My old school top loader lasted longer than this piece of junk! I believe the steam from the wash is going up into the control board and messing it all up! Water and electricity does not mix! Maybe they need to relook at their products. I want my money back!!!

Posted the following review of this oven on the Whirlpool website: How did this get 5 stars with so many complaints? Ive only used this oven once since installed last Sunday. It heated my kitchen up at least 3 degrees. I live in the South so evidently its not meant for southern summers. It does look nice but if Id known the fan blows such hot air out of the bottom, I wouldnt have chosen this one. Afraid if I use the self cleaning cycle, it will burn my hard wood floor. Probably why there are many complaints about uneven cooking and long to preheat since all the heat is blowing out of the bottom. I received an email saying it didnt meet their website guidelines and they wouldnt post it. Interesting?!

Immediately after install, the oven door face kept coming loose, they did send someone to fix & replace. Ive used the self cleaning twice, first time was fine, second time not so much. The cleaning process left major scrum below the window inside the door & below, which wasnt there before I did the clean. I take great pride in keeping my oven clean, do not allow build up because then you cant get it clean. This stove is less than a year old & has only been in place for 6 1/2 mths (I purchased before remodeling was complete).My last stove I sold easily, it was clean & guess what. It was 32 years old, only replaced because of updating our kitchen!!! I contacted whirlpool & they said its cosmetic & not covered. I called Lowes, they refer me to the service advance phone #. Well that was Whirlpool, not Lowes. Still nothing being done, other than they sent me cleaning stuff to try and get it cleaned (still working on that). Im concerned this stove is going to continue to have issues & will be out of warranty soon. Whirlpool is not standing behind their products & we have been Whirlpool customers for a long time. If I have more issues with this stove, we will never purchase Whirlpool again. Dont buy their products, they dont stand behind them!

Just bought this washer, its making a lot of noise, sounds like something is grinding (metal, gears, etc). I thought Whirlpool was suppose to be good. I just had my Maytag go out after 18 years of service, thought about getting another Maytag but found out Whirlpool makes those. As many complaint as I see, seems there needs to be a class action lawsuit against Whirlpool for shoddy work.

I have a model FG1F4034T3NOV water heater that was a problem since day one. The pilot will not stay lit, and apparently, there was some sort of class action lawsuit due to a defective part that I missed out on because I didnt know about it. The telephone representative is quick to point out that it is out of warranty due to the date of manufacture and that it needs about $200 in parts because I cant find the receipt from 4 years ago, when I bought it from Lowes. The company flat out refused to do a courtesy replacement for parts or discount them.

Do not buy a Whirlpool refrigerator. This is the 3rd time I have to call in repair for the ice maker in 4 years. Water poured out on my floor for the 3rd time ruining my floors. Called Whirlpool and said there is nothing they can do to help me. They don’t care about their Customers! I could have bought a new one by now based on repair costs. They don’t back their products. I’m really annoyed now!

First my pump went out on a 4 month old washer. Had to wait several days for them to fix it. My washer worked for two weeks and same problem. Its been over a week and the service man cancels then shows up and tells me pumps out and can get one for several weeks. I cant stand them still not fixed.

We purchased our Whirlpool Refrigerator #WRT519SZDB from the Home Depot 2 years and 10 Months ago. About three weeks ago it started to freeze items in the frig section. We lowered the frig section cooling level one selection and went on a two week vacation. When we came back, everything in the freezer section was thawed out. We had a tech look at it and he told us that the compressor was partly seized and overheating. Tried to reach someone at Whirlpool customer service by phone, email, and chat but so far, I have not had anyone contact Me back? Looks like repair will cost almost as much as a replacement refrigerator. So much for Whirlpool being a trusted brand!

We purchased a Cabrio washer in August 2013, in early August 2014 we noticed that it was not getting all of the detergent out of the clothes (noticed it on the dark clothes after drying). We use less than the recommended amount of HE detergent and dilute it in the dispenser, also always use the extra rinse. We just had a Sears service man out at a $100 cost only to find out that he gets these calls all of the time and the machine is operating at the factory settings.After reporting the problem to Whirlpool all I got was we are sorry and a link to how to operate the washer. In the demonstration video it clearly shows that the water level never covers the clothes. I know Im old school but in my opinion the water should cover the clothes so it can properly wet and agitate the items in the washer. To say I am less than satisfied is a gross understatement. Im out the cost of the washer plus an additional $100 and after a year of ownership and contacting Whirlpool less than a week after the factory warranty ran out all I get is an Im sorry you do not know how to operate a washer.

We bought this washer brand new and as soon as it was outside the one year warranty the bearing went out. They had to order a whole new drum kit. A MONTH later I had a running washing machine again. The day after it was fixed it started leaking underneath the machine. Serviceman came and looked at it and said No must be the hoses (my responsibility to fix). Nope kept leaking and two months later Im doing laundry and an entire load of water floods my laundry room. Drum broke again!! SIX WEEKS LATER I still am waiting for a new drum. I had to fight to get Whirlpool to fix it again and they wont even return my calls about why its taking so long! We are a family of 8, so doing laundry at a laundromat is outrageous! Dont ever buy Whirlpool washers!!!

We purchased the Whirlpool double oven with convection to go into our new home 18 months ago. I used the self-cleaning cycle on the bottom oven for the first time last weekend. Halfway through the cycle the control panel went blank. Basically both ovens died, and the bottom oven door is locked. After researching online I learned that this has been an issue with the self-cleaning feature on Whirlpool ovens for some time now. So buyer beware, if you decide to purchase, dont use the self-cleaning feature.

We purchased Whirlpool Gold appliances because we thought that they had an excellent reputation? Wrong! Our Whirlpool refrigerator lining started cracking before the unit was 3 years old. Now its 7 years & cracks are so deep and there are so many of them, the refrigerator must be replaced. No help from Whirlpool when I called. Now remember, a refrigerator is supposed to last 14-17 years. 7 years is not acceptable!This is a known problem. If you Google refrigerator liner cracks Whirlpool youll see many of them. Unfortunately, Whirlpool will not accept responsibility for faulty design/manufacturing which leaves the consumer to be out of their hard-earned money. Before you ever buy a Whirlpool product, read the reviews and decide if Whirlpool not standing behind their products makes it worth it for you to buy them. I certainly dont recommend them! I also wish to tell you that a major crack was around the light housing and Whirlpool placed the light cover over it where it was concealed to the buyer. Youd never know it until the light cover would be removed for cleaning. Which wasnt easy to do since Whirlpool installed it with 2 sided sticky glue foam tape. Now thats really scum behavior!

We too have nothing but problems with our supposedly top of the line convection/microwave oven. Purchased in 2010 in February for new kitchen. From start, original microwave installed did not work, would not cook or heat. Dealer replaced. One year later, same problem, but now out of warranty. Had to pay labor, costs, and parts to get fixed. Fast forward 13 months, again magnetron needs replaced, microwave will not work. What a hunk of junk for our money. I will never buy any Whirlpool appliances again, and I will tell everyone I know the same. When you call customer service, they are nice but only say “too bad, out of warranty”. What a joke for a major appliance company to tell customers. It is obvious that this microwave is faulty from the get go, and they just keep on making them the same way and not trying to fix the problem.

I am posting to help anyone else avoid the purchase of this machine! The lid has cracked and now warped into a position where it wont stay down. Obviously a washer will not work without being in the locked position, so we have to put several heavy things on top of it just to run a load of laundry. This is not what we expect out of a washer that we paid $900 for only two years ago!!!! We contacted Whirlpool and they offered to fix it for $350. REALLY??? I SHOULD NOT have to pour money into a washer this expensive after two years!!!! I am so disappointed in Whirlpool, this was the entire reason we purchased Whirlpool products, to avoid stress of broken appliances. We wanted reliability for our busy family and instead we bought into more stress.

I purchased my Whirlpool French door refrigerator about 2 years ago. I shopped around and read reviews before deciding on the Whirlpool. After about 9-10 months the ice maker didn’t seem to produce enough ice. I called the store I purchased it at and tried to get them to come out and find out what was wrong. They waited and waited. I had to call them back at least 2 times before they finally sent someone. But by the time they sent someone to look at it the one year warranty had expired. I spent $1800.00 on this refrigerator and it didn’t even last longer than a year. Of course Whirlpool wanted to come look at it and charge me another $100.00 service call and possibly another $100.00 for parts and labor. I will never buy a Whirlpool product again.

We bought all new Whirlpool kitchen appliances in February of 2017. The French Door Refridgerator MRF993FIFM we purchased was a large side by side with a water/ice dispenser and freezer on the bottom. The concept of it is great, as it is very roomy. The problem is with the product quality and usability. We are a family of four with the youngest being twelve. We do not have to worry about rough little hands anymore. That being said there is a crack in the back of the plastic casing of one shelf, a crack in the freezer door, the seal doesnt connect on the dispenser side door, the slide out shelf in the freezer doesnt stay on its rollers and the main ice maker stopped working (which never worked properly either).Also, and this is what bothers me the most, the glass on one of the shelves is sealed down so it cannot be cleaned under. But there is a small slit going all the way around that separates it from the plastic. Food is still seeping underneath and creating mold with no way to clean underneath! This was not an inexpensive refrigerator and we were not prepared to have these kinds of problems after a year. We are very unhappy with the quality of this product.

Eleven months after purchasing a Whirlpool refrigerator for our office lunch room it stopped working. While the refrigerator was still under warranty, I called Whirlpool for a service call. I was informed that the warranty is voided because the unit is located at a business and not a residential property. I explained to the customer service agent that there is no mention of this policy until after the appliance is purchased. After a considerable amount of time on the phone speaking with several supervisors, I was connected to a Resolution Specialist. She informed me that this policy is available online for consumers to view prior to purchasing Whirlpool appliances and it is the consumers Due Diligence to research warranty policies before purchasing. Consumers beware! Warranties are voided on all Whirlpool appliances that are located at a business address.

Whirlpool washing machine has always been reliable for me. I have owned 2 and they lasted me many many years. Its easy to use, and cleans clothes perfectly. My family is also a fan of Whirlpool appliances.

In 2015 door of top loading washer (Whirlpool Cabrio Washer) needed total replacement. Lucky I had an extended warranty. 2018 March, extended warranty expired and now have the exact same problem. Pretty crummy product if major part like a door has to be replaced every 3-4 years. We do not wash large items like blankets/quilts in this machine. That goes to a laundromat where there are oversized machines or to a dry cleaner. So the only reason for this breakage is a default in the lid assembly. There is only one phone number for customer service, repair, parts etc. Put in my service call and filed a complaint at same time hoping for at least a small discount. Ha! $100 plus tax for service call- part price ranges from $150-230 plus tax. Whirlpool could tell me the part exists but would not say how long it takes to get it! Do NOT buy Whirlpool washer with top load lid that has glass window. Big problem is that Whirlpool now has Jenn-Air, KitchenAid, Maytag and Amana all under their umbrella.

Whirlpool refrigerator is 2 years old and has LED lighting. Light went out in freezer and dimmed in refrigerator. Requires a technician to replace them with 3 hours of labor due to wiring. Total cost parts and labor $700. Whirlpool has a one year warranty and was unwilling to repair at their cost. Warning - do not purchase any refrigerator with LED lighting that requires a technician to replace the lights.

Our range emits smoke and a toxic odor spontaneously when not in use. We feel it could be a potential fire hazard. We have had repair people and fire department out. We have contacted the manufacturer numerous times and they do not return our calls.

I filed a complaint late Oct. 4, 2011 about a problem I was having with one of my Whirlpool water heaters. Chris from Whirlpool emailed and phoned me twice within 12 hours! He was courteous and very helpful. He shipped the parts that I needed overnight. They came in this evening, I installed them and everything is working great! Thanks to Whirlpool and Chris, we now have hot water!

Out of warranty, slab of ice forms every few weeks in bottom of freezer. I have to take a butter knife and chisel it out to prevent having to defrost the entire freezer. This is clearly not isolated as after reading online and this forum, it is a manufacturing DEFECT that should be fixed at no charge to the consumer. It was delivered and installed by the retailer that sold the brand - however it sounds that Whirlpool would rather lose customers to other brands - trust me I just bought a stove and bet your sweet behind it was NOT a Whirlpool. Neither will the replacement for this piece of crap be once I can scrounge up the money.

We have our stove for over five years and we have had no problems with it over the years. It has a black top and this seems like it is a little harder to clean, but other from that we have had no problems with either stove or oven.

I purchased a Whirlpool washer (WTW4800Q) in November 2011. Already, it has rust in the tub. The warranty does not cover this. I never really liked the thing since I have had it. It takes much too long. Lid locks and then starts over. Also, warranty is not good. I wouldnt ever buy their product again and suggest no one else should either. I loved Maytag before Whirlpool bought them out. Im putting this one on Craigslist and buying a real washer, a Speed Queen! Yes, Speed Queen has all metal parts and makes a home washer. Just have to find a local dealer. They are there.

Piece of junk that tears up clothes but doesnt clean. Company has ZERO care for their customers. I will never buy Whirlpool again. We called and called and called. Washer took two hours for a normal load. Crust and odors still there. Dryer was fine.

I count myself as lucky... my Whirlpool 465 Accubake Ceramic Cooktop stove was given to me. I have used it for 3 years. One day, out of the blue, the oven, which was in use, started clanging loud and jumping up and down. I started screaming & tried to cut it off & it would not go off. I ran to the panel box & threw the breaker. It also burned my food that was cooking. It did it several times. Then I decided to not cut the light on or touch the button to raise the temp. It has not done it since. I bake everything on 350 degrees and immediately throw the breaker. I am scared of this stove and plan to replace it. I will NOT buy a Whirlpool, anything. (washer/dryer/fridge/aircon)....once bitten...

My Whirlpool microwave broke. Im not sure how or why so today I purchased another 2 actually. Both were too big. The model I purchased is discontinued. I had to remove part of my Marble Backsplash - the turntable is tiny however mic is huge. Work on making microwave for smaller areas. Stick to get or Samsung for a nice size microwave not a Mongo mega oven above your oven.

I purchased a water heater Model # UG1H50400TBN, Serial # 0913T400920, from Lowes in Corona, CA. 05/07/2009 for $528 plus tax. I have replaced the following parts: 02/10/2010 Thermostat Valve, 07/23/2010 Thermostat Valve (2nd time), 08/10/2010 Burner assembly, 02/10/2011 Thermocouple, 02/17/2011 Thermostat Valve (3rd time), 12/17/2014 Thermocouple (2nd time) and 03/20/2015 Burner assembly (2nd time).Today I called WHIRLPOOL Customer service (877) 817-6750 because my water heater water is warm. I told the tech support agent that the pilot light was on so we agreed that it was the thermostat valve AGAIN. He wanted $30 for overnight delivery and I refused to pay. Now I have to go out and buy this part because Whirlpool like the Banks is too big to fail and they have license to RIP-OFF the consumer without penalties. Whirlpool has all of information and they can verify everything I wrote here just by the serial number.

We bought the Whirlpool Duet set for $1,000 18 months ago. About four months ago, it started shredding our clothes. I would get them out with holes in them, but there was nothing sharp in the washer. Then the grey outside seal started deteriorating and getting tiny balls of rubber all over my clothes, ruining several white shirts. It always smells like mold. I just went to get my clothes out of it to find out it leaked water all over with that disintegrated rubber from the seal. The seal had completely ripped from the top to the bottom drain for no apparent reason. Now we are replacing the below. We JUST paid it off this month. It is crazy, it is already breaking!

Hi Folks, so today I had the pleasure to speak to Whirlpool regarding a repair bill on our washing machine which now has a bearing failure and estimate to repair was 1279.00. Its 6.5 Yrs old, just out of extended warranty and cost me with the pedestal a total of 1250.00 when new. I explained that in the 6.5 since I have lived at this house where we spend all new Whirlpool Gold Appliances, half have now failed. Range Microwave, Dishwasher and now the 1250.00 front loader is dying a slow and agonizing death with a bearing failure. Just so everyone understands, the estimate is from an official Whirlpool repair service that was booked through the Whirlpool website. Other repair folks just would not bother to look at it when I told them I believe the bearing was going bad.The repair man that arrived was professional and on time. However, I had a hard time understanding how a 6.5 Yr old washing machine would be considered beyond economical repair by costing 1279.00 to repair. Labor was 250.00 which I thought was fair. Time, etc. But parts made up the difference in cost. So later in the day, I spoke to Whirlpool and they offered the equal new washer for what would seem an excellent price. About half off. Wow, I thought that sounded good. So I asked if my existing pedestal would work with the new washer and it did not and I would have to pay for one. Regardless if my old one was fine or not.So, they offered a discounted rate from new at another half off. Total approx 800.00. So, I asked the Whirlpool rep to hold on and I need to check with my wife if she wants the replacement. She uses it as much as I do and wanted her thoughts. She checked the model on the washer and pedestal and with the local Home improvement store, they have it on sale for both units (washer and pedestal) and its about 50.00 less?Consequently, I called Whirlpool back and explained that it does not move the needle to regain my trust as compensation on a 6 yr bearing failure, failed dishwasher and range microwave they offer what a distributor of their product can offer for less as a package? Really? I mean, the Home improvement store is not in the business to lose money. Now, I am having a hard time understanding my own failure to have trust in a brand I used to have with my previous house.My mom had an old Whirlpool washing machine that lasted 25 years before she and my dad gave it away. You know, the old white top loader they used to make back in the 70s. Sheet metal, made a racket and never broke? Oh yeah got the clothes clean too! I dont know what to make of it anymore. So, I will just wait till it dies and take my hard earned money and spend it on another brand in my next house which we are going to move to soon. Maybe I can feel nostalgic and find my moms old washer. Its probably washing someones rags right now and getting them clean. It must be 35 yrs old by now.I dont expect to get anything for free. Its out of warranty, so I need to deal with the consequences, but there are steps the other party can take to help remedy the situation. I think they tried and it was genuine but in my thoughts its just not enough when your local box store is offering the same. When you develop a brand to extend a message of trust in quality and value, you need to have quality and value all the time. I suggested they help with the costs on the parts. I would certainly pay for the labor. Parts cost little to the manufacturer. Unable to help that way. I thought it was cheaper for them too. Guess not. Its come to be a throw away washing machine at 6.5 yrs and I am Infinitely disappointed. I just want my washing machine to work as well as my mothers old one and have the possibility to fix once in a while when needed.

I purchased a Whirlpool Gold side-by-side Refrigerator on June 15, 2013. The freezer works fine but the refrigerator does not feel that cold and when I put a thermometer in there, it reads 42-43 deg although the refrigerator is set at 37 deg. The tech was just here and told me to put a thermometer in a glass of water and read it again. His thermometer read 46 deg when reading a bottle in the door although he explained that he had had the door opened for a while during his visit. He said his reading of the bottle upon opening the door was 36 deg. I do not believe that. I just measured some bottled water temperature and it was 48 deg. I have a hard time believing the temp went up 12 degrees and he has been gone for a half hour. My food is cold but not like you expect from a refrigerator. My bottled water and soda, etc., are not very cold. The worst is the water dispenser. That water is barely cooler than tap water. There is almost no difference. The water temperature has been in the 60s when Ive measured it. The tech says the first glass wont be cold (have never had that with any other refrigerator) but even if you get the second and third glasses of water, they arent any colder... maybe a couple of degrees. If anyone else is having this problem and Whirlpool will do nothing, then Im interested in legal action.

When the fridge is running and there is a power loss of about a second or so, the fridge shuts down and will not restart (even after hours). I have to unplug it for a minute or so then plug it back in; it runs fine until the next very short power failure. When we are out of town for a few days and that happens, we come home to a fridge of ruined food and a mess. I have contacted Whirlpool (2 times) and they were no help at all. It seems to me a software change could solve the problem, but they are unwilling to listen.

What a horrible machine! From the day that it was installed not one time it gave me good cleaning. I spent so much money servicing it. Costed me over $700! I am done putting money into it! I am washing by hand! If you want a dishwasher where you can hand wash and God forbid your rinse with the machine (you will have to rewash everything) then this is the machine for you!

I owned a Whirlpool water heater and the only thing I have with it is problems! The pilot keeps on turning off. Since I am a 64-year-old lady, I have no idea on how to fix things (widowed). I keep on paying for the plumber to fix it. It started with flooding all my front yard because of a faulty valve. I paid $165.00. After the pilot went off, I paid another bill to fix that. And it turned off and on again (lost count of times). Today, I found another pool of water (the valve again? ). What a piece of work! Please, can you help me? Im heading to the store to buy a new one, not a Whirlpool!

Yes, Whirlpool makes Maytag, Im still paying for this junk. Too much to go into detail. I had to bypass the crummy fuse system in the Bravo dryer and hook up my own 15amp automotive fuse in the dryer to keep it working. This after two lame under-contract Maytag repairmen replaced the dreaded board, which did nothing. The washer goes cabunk, cabunk, cabunk throughout the house and shuts down with an unlevel code (no matter how level the load is) every time it does its load during the spin cycle. The dishwasher handle broke off and had to use a screwdriver to pry the handle latch open, until realized it doesnt even lock anyway and just pulled the door open. Now, the dishwasher has this noise problem which means they designed it to allow pieces of debris to escape past the trap like my other dishwasher had that was easy to remove and clean. Do not, I repeat, do not pay the $3,500+ I paid for this junk. Go buy a Kenmore thats 15 years old off of Craigslist! Youll be better off and it will last longer.

We had the unfortunate experience of purchasing a Whirlpool product from Lowes. During Memorial Day weekend we came home to a freezer full of defrosted meat. After having to throw away 1/3 of a steer that we purchased from a local 4-H students project due to the temperature of the meat and not knowing how long it had been at that temperature. I called Lowes and they said there was nothing they could do for me since the freezer was over 1 month old. It was right at 2 months. (Purchase date - failure date). They advised me to call Whirlpool directly and gave me a number to the warranty technician. The warranty technician came and immediately found the problem. The defrosting connector was not plugged in when it was manufactured. Clearly a manufacturer issue. I called Whirlpool to find out how much of my over $1500 of meat they would cover. They told me they would not cover any of the loss. Then they offered me a 1 year extended warranty for free for my Inconvenience. What a slap in the face. Why would I need a warranty or even a freezer for that matter since I no longer have anything to put in it. Needless to say I will no longer purchase any products from Lowes or Whirlpool.

I have a Whirlpool refrigerator from 2017 that is causing so many issues and finally completely broken after spending $500 on repairs. 4 months ago, refrigerator was making loud noise and freezer wasnt working. Then within a week the whole unit stopped working. Then, freezer got all frosty and the whole unit got shut off. 2 month later, the ice maker stopped working and nothing is working now. I called the Whirlpool and they offered me to purchase extended warranty for $530. I could not believe they wanted me to spend another $530 on this refrigerator after spending all this money on repairs and still useless. I refused to buy any more Whirlpool product that I used to love in the past. I am just so disappointed with the customer service as the supervisor from Whirlpool said that is why they offer extended warranty. $2000 refrigerator to last me 3 years???? Not doing this again.

It is in the mid-range of cost and functions. For a mid-range dishwasher, it has many options, sometimes too many. It does not have rinse and hold. I think its cycles run too long; not always energy efficient (i.e. the simplest one uses the most energy).

Purchased this washer in 2009 from Lowes, believing the hype that it was efficient. Since we only needed a Washer at the time, we overpaid (it is more cost effective when you buy both washer and dryer). So we paid $1000.00 for this machine (we purchased the stand as well). After the 1st year, there seemed to be a significant decrease in how fast the washer spun, as the clothes were coming out wetter. I didnt pay much attention, but 2 years later, the machine has a weird problem where it couldnt complete the cycle, and by this time, every time it Spun, the noise was louder and louder.I contact Whirlpool, placed a service call and the Technician came out. $225.00 later, there was a hose that was pinched that was sending a wrong signal to the washer. He fixed that and told me I should get a contract on the machine through Whirlpool since I seemed to be having problems. I purchased the contract, for $300.00, and 2 1/2 weeks later placed another service call, as the noise from the machine was happening every time I did laundry. The service guy came out, indicated that it seemed to be the Agitator, and that he would need to order parts, and that they had a SPECIALIST who only does this type of repair, since they have many! He also indicated that the hose may have crimped due to the movement of the entire agitator!Well, after not hearing from ANYONE for 2 weeks, I called the repair company who told me WHIRLPOOL was supposed to call and let me know that they would NOT fix the machine, as the parts cost more than the Washer, which is now valued at $500.00! No one from WHIRLPOOL EVER CALLED, and I cant understand how a $1000.00 Washing machine touted to be so efficient and environmentally friendly has been THROWN OUT after 3 years!!! And now I am out the $225.00 repair, have no washing machine, $1000.00 down the drain (and I forgot to mention a year later we bought the matching WHIRLPOOL DRYER and OVERPAID) and now have to purchase another machine, which I assure you WONT BE WHIRLPOOL! As most of us have experienced, WASHING MACHINES last for many years! The washer I had before this was over 20 years!!!! So much for efficient and environmentally friendly... The only thing GREEN about this machine is how much of my $$$ has gone to Whirlpool!

Purchased Whirlpool Cabrio top loading washing machine yesterday. When wash load is finished (dark load) white marks are visible on the clothing. It appears to be laundry detergent that has not dissolved. I am not happy with this washer and will be returning it.

I purchased my Whirlpool refrigerator from Best Buy 11/20/19. It has been nothing but a nightmare. It freezes up and defrosts into the refrigerator.! I called Whirlpool about the situation. The company they use to fix my fridge S&S Appliance has not been keeping accurate records. I have all the calls from Best Buy and S&S Appliance. I was told today-all my records didn’t count. Best Buy Geek Squad couldn’t repair so they turned everything over to Whirlpool. So about every week someone comes out and fiddles with it and tell me it is fine. 2 days later the same. I have owned many Whirlpool products and never have I been so disappointed. Their service has been neglecting and I don’t know how anyone would want to buy Whirlpool. They have set me up another service appointment with S&S Appliance. Obviously I have bought a lemon and no one takes any responsibility. Good luck with Whirlpool!!

We purchased the Whirlpool Cabrio washer & dryer. The glass lid design is VERY POORLY constructed and should be replaced by Whirlpool. We paid over $200 the first time the lid broke and was told this is going to be a continuing problem. They were correct! We subsequently replaced the lid 2 additional times only to have the same break on the right hand side causing the lid to pop up. Something must be done and WHIRLPOOL need to care for their machinery. They should replace the lids or provide a major incentive for consumers to replace the washer. PLEASE DO SOMETHING!

The water dispenser tube cracked and split off near the dispensing end, making the dispenser unusable. Not a consumer repair, by any means. Refrigerator is only a year old. I had a similar parts quality issue with a Whirlpool dishwasher. I will never purchase another Whirlpool appliance, and will advise all to avoid as well.

I purchased Whirlpool gas range. After approximately 1 year, it has repeated problems with oven failing to maintain temperature. The unit would remain on, with the bake on still showing. But the temperature would decrease to the point of not cooking the food. If you turned the oven off and then back on, it would preheat again and resume baking, only to kick back off again later (again, with the bake still on).

I like this refrigerator. Its a two door. I did not get an icemaker and I have plenty of freezer room. The milk will stay fresh at least for a month. I like the crispers. They keep my food fresh. It keeped the Romain lettuce very fresh on the package, it was pick 7/31/2019 and just have a fresh green Salad Sept 6, 2019. Easy to move when wanting to clean the floor.

Ive had my Whirlpool water heater for almost 4 years now and for the last year and a half, I had to have the pilot light lit at least 5 times. I finally got so frustrated around the 3 times and called the company. They gave me instructions on how to light it and to ensure no draft was around the tank. A couple of weeks ago, it went out again and I called. This time I was told to replace the thermocouple. I did that and guess what? Still no hot water. Im a single parent with 2 kids and weve been boiling water just to bath.A service tech came out and told me I need to replace the tank altogether. I called Whirlpool service and they told me it was nothing they can do. Like many of you, I got this tank from Lowes and they will not do anything about it either. Its hurtful and stressful that doing a holiday season, I have to decide to either buy a hot water tank or give my kids a good Christmas. I know several friends and family who has had their tanks a lot longer with no problem. My problem is its a crappy Whirlpool brand with poor customer service.

I like the Whirlpool oven ranges because it is easy to operate, easy to clean and like the features and functions. I have had no issues with the stove and I have had it for four years already. So far still working good.

I purchased a Whirlpool range from Lowes for $750.00. After 13 months, the digital circuit board went out and cost $580.00 to repair. I thought this was odd since the range was fairly new. The service tech said the boards are a common problem. Two years later, when using the self-cleaning mode, the door was locked and the board was out again. So this must be the issue because that is the same problem that happened the first time. This must be a design flaw! The board cannot handle the heat generated in self-clean mode. Way to go Whirlpool, put the board near the oven door where it is subjected to extreme heat and melts!

My Whirlpool side-by-side refrigerator is just 4 years old. When they delivered it, they noticed damage on the bottom which required them to bring me a new refrigerator. The new one had issues with the ice maker that required multiple service calls to fix. The refrigerator door always seemed a bit misaligned as it was a bit lower than the freezer door, but it closed, so I never complained. I was just tired of all the issues! During the last six months, the door started to remain ajar instead of closing completely so that we had to always be sure to apply sufficient pressure to close it tightly. I considered calling in a repair, but it was still closing so I thought I might be overly critical. As it got worse, I realized the door was defective, but one day, it just fell off completely without warning as though the hinges were made of butter!After multiple service calls, a tech reattached the door, but I could see that it would not hold and sure enough, it is starting to remain ajar again. I have contacted the warranty company who is now saying the service tech claimed we were hanging on the door. This repair company the warranty company uses has an F rating with the BBB. Now, Im being told it may take a couple weeks to get another repair company to give them an opinion, but the issue is clear, the door was defective and it looks like they found a way to avoid having to make good on the warranty!

This machine is 18 months old. First it failed to drain (LD code). Ran diagnostics and found the drain pump ($60) failed. The Mexican part was replaced with an Italian part. Two weeks later, the infamous F1 code flashed - control board. I sourced a new one. I ran one load and another F1 code is flashing. These are $150 electronic parts. Fuhgetaboutit. Im sending this ** to the dump and going back to electromechanical controls. I had a Maytag that lasted 15 years.

We purchased a Whirlpool washer/dryer set 19 months ago and the washer just stopped working. Our trusted fix-it man came out and diagnosed it as a spin bearing problem assuring me it was not anything we had done. He stated it was a defected part or Whirlpool had never put grease in the bearings. A 450.00 part not counting diagnosis and labor. When I called Whirlpool, the first response I got was that they were sorry but we didnt buy the extended warranty, and of course the warranty it had was only a year. I asked to talked to a supervisor and finally she agreed to supply the part, but I was still responsible for the diagnostic and labor fee, which will be a couple of hundreds of dollars! Not happy with Whirlpool and will NEVER buy any product with their name again. Beware consumers!!!

Cabrio top load HE washer - Ive only had the washer a couple of years. My husband bought it for me thinking it would make washing more time efficient and energy saving. Lesson learned! After struggling with this washer for the past year, I was told today that to repair it, it would cost around $800 or I would need to buy another washer. The washers bearings and tub need to be replaced and it will not spin properly or at all. Previously, I have owned washers for over 10 years each. This was definitely not a good purchase. After reading all of the other complaints on this site, I understand that I am not alone. It was also mentioned on one complaint of the possibility of a fire hazard with this washer. Whirlpool should be recalling.