The front of our Whirlpool washing machine started to rust in one place at the bottom within six years. Now it has broken out in three of four places on the front. We are very dissatisfied with machine and will never buy one again.

I bought my fridge in late 2008 and I am already experiencing potentially expensive repairs due to what I believe is a defective design system, of which, consumers are having to bare the consequences for those who collected our hard-earned cash and delivered a lousy product! I saw so many similar complaints about the ice system on this fridge that I am almost positive that it qualifies for a class action suit and settlement. How about a collaborative approach to this since we have all suffered needlessly? Tell me what you think and if you are in on it.

Whirlpool Cabrio Washer Model WTW6400SW2 Serial CU0272414: I replaced my wonderful 25+ year old Kenmore washer with the Cabrio, 4 years ago. Within the first year I had to have a computer board replaced that was covered under the warranty. This last 6 months I replaced the suspension rods, was constantly showing that the load was unbalanced. Also have a LD error, long drain, probably because a sensor is bad. Today, restarted a load several times and could never complete the entire cycle. I resorted to unplugging, and starting a drain spin cycle and the washer just flooded my house. So Im done with this unit. Waiting for a class action suit. Lets get started. What type of unit should I buy now. I guess Im going to subscribe to Consumer Report before I buy another. Laundromat for me in the meantime.

I bought a Whirlpool washer and dryer a little over a year now and the washer is not filling enough water for the cycle to wash properly. I have to fill the washer myself and this only started a couple of months ago. This happens even when I have a heavy supply of water.

After reading many of the 1,500 +/- complaints about this inferior product, I guess I should consider myself lucky. Ours didnt fail until this past Saturday, March 22, 2014. We purchased this Whirlpool (American Water Heater Company) water heater FG1H4040T3NOV at Lowes, and had it professionally installed, in October 2004, and we have had no issues until this past Saturday when we woke up to no hot water. After checking for the obvious, and finding no apparent cause for the failure, I considered it a fluke and relighted the pilot. The pilot took a few attempts to light, but it lit, and the burners came on.Three days later, we woke to no hot water again. This time, we placed a service call to the company that did the initial install. The technician came out, and after his inspection he informed me that the thermocouple/burner assembly needed to be replaced. He also informed me that this is a well-known issue, and Whirlpool has been sending out free updated replacement parts. He called Whirlpool, only to be told that they are no longer offering free, updated parts. Whirlpool also cited that the water heater was out of warranty (by less than 5 months). He gave me Whirlpools number, so I could contact them myself.As I smelled a rat, I began to do some online research about this issue, and, to my chagrin, I found out that I was far from alone with this issue. As of this writing, 1,500+ consumer and professional complaints, a settled class-action lawsuit, etc., etc. I contacted Whirlpool, explained my situation to the support rep, and, he proceeded to tell me that he couldnt help me with free replacement parts, due to the warranty being expired (less than 5 months). I argued with him, stating that this is not a warranty issue, but is in-fact a design/manufacturing defect issue, that has resulted in a redesign/re-manufacture. I cited the myriad of online data and negative testimonials, and I reminded him about the settled class-action lawsuit on this very topic. He acknowledged all of the above, was unimpressed, and offered to sell me the parts.After 15 minutes of back and forth, I asked to be escalated to the next level. But, of course the supervisor was unavailable, and If Id care to leave my name and number... yeah, right. Bottom line, Im very angry! I paid good money to Lowes for Whirlpools product, with a nine-year warranty. I had it professionally installed, and we have no hot water due to poorly designed parts. And... I am being forced to purchase the redesigned parts. Its truly unsatisfying to be an American consumer these days!

I bought my Cabrio washer about 3.5 years ago. Little after the year, I had to replace the lid because the hinge broke. Then came the F1 code, which I noticed if you turn the machine off for a couple of minutes, it resets itself. About a week ago, it started making a grinding noise and staining the clothes with oil or grease. Transmission problems. I was told by the seller it had a 10 year warranty. I called them up and now I got to foot the bill for a technician to come to my house and tell me what I already know plus labor. Might as well buy a new one. Beware because I believe Kenmore is manufactured by the same company.

Whirlpool Cabrio Platinum washing machine: You wont believe this until you call a parts replacement place for tiny part. The plastic (or vinyl) lid hinge bearings are located at hinge corners of lid. Hinge pin passes through them, one on each side. Half the size of a penny, UNCONSCIONABLE greed at the price of $32-$33 dollars EACH when ordered from a parts place. IMHO, design by INTENTIONAL failure to fail after three or four years. As a result, the lid will not stay up on its own. Then you find out the horrible news which is an insult to intelligence. Id have expected to pay maybe two or three dollars each, but NEVER the price they are demanding. Theyve got you and there is NOTHING you can do about it. At that rate, parts would run tens of thousands of dollars to replace the entire machine, part by part. These greedy clowns make car dealers look like reasonable people! The LAST Whirlpool machine of ANY kind we will EVER own!

We have owned refrigerators for over 40 years. Never had one as bad as this. Three ice maker replacements lasting maybe from 6 months to 2 years. Cap that off with customer service people who by voice and tone could not give a rats ** about helping the customer. Today it took me from 3:10 pm to 5:30 pm to get a real person on the phone. When I did the attitude is so reminiscent of a fast food hamburger joint with arches. Yes they know the refrig and ice maker are and have been a problem but they don’t care cause we have no option. Whirlpool will NEVER SEE ANOTHER penny of my money. Time to look at real appliance makers. Horrible.

I recently purchased the Whirlpool Cabrio washer and it is the worst product ever!! It does not wash the clothes, it tangles it in knots and has ruined all of my clothes because it leaves holes in the clothing. I have had multiple service calls and all of the diagnostics check out. It is a horrible product that should be recalled and Whirlpool customer service does not stand by their product. Their supervisors and customer service is very rude and I will never purchase another Whirlpool product!!! I plan on posting my complaint everywhere possible.

This refrigerator is less than 1 yr. Old and this repair will be the FOURTH. The severe lack of craftsmanship and customer service is shocking! Most states do not have lemon laws for appliances, however something needs to be done to compensate me for THE TIME and inconvenience this caused my family. I needed to purchase a second compact refrigerator because I knew that it would break down again!

Whirlpool microwave came with my new condo, and its as aesthetically pleasing as it is functional. Very easy to use, sounds are not annoying (as my last microwave was) and heats food quickly and evenly, as needed.

Our daughter has a Whirlpool Duet front loader washer & dryer combination which is less than 3 years old. The washer shows fault code 71 and will not run or release the door lock. The first repairman said the interface board and/or a computer will need to be replaced. Cost is $600 to $1,000. I called Whirlpool. They recommended their trained tech be called out. He looked at the broken machine and determined the interface board was bad, and he put a temporary repair on the washer and said Its okay to use for now. He will return in 2 weeks with the replacement part. We tried the machine with a load of clothes. The machine filled up with water then quit, and the door was locked. We called to get a tech to open the door so we could retrieve our clothes. No one is available for 1 1/2 week. I called Whirlpool and was told a claim form would be mailed to me so we could be compensated for the damaged clothes. The letter arrived. I was appalled when I read it. First, it came from their Legal dept. The intent was to scare us into getting a lawyer or just use our homeowners insurance for the damaged clothes claim. I called Whirlpool back several times and was told too bad, so sad. Whirlpool might make a good machine; they cant prove it by me but their support rates a big zero.

Whirlpool hot water heater - The water coming from the faucets when it is hot is red. Therefore, I contacted Whirlpool and was informed that the anode has failed. The anode is not covered because, according to this company, it is not considered a working part. It baffles me that the anode is not a working part since it keeps the tank from rotting. I have only had the hot water tank for three years and this part has failed causing my hot water to be red. Since this company contradicts itself, I either have to live with red hot water (rust) or replace the part on my own. Unlike your company, Lowes has customer service. They apologized and will be paying for half of the expense for the part. Unfortunately, I still must pay for an employee to replace the part. This whole situation is absolutely ridiculous. I will never be purchasing another item from your company and in addition to that, I will tell everyone I know to avoid this company at all costs. You should strongly consider revising this policy before you lose all of your customers.

My washing machine would not spin dry. I had a new pressure switch replaced to a tune of $180.00 which was only 26 months old. I have always bought Whirlpool but this will be my last whirlpool appliance.

We purchased our Whirlpool Refrigerator, oven, and microwave a little more than a year ago. Not a single negative event with any of these products and my wife and I wholeheartedly recommend Whirlpool for operation and last ability, unlike the products we replaced them with.

We bought a WRS325FDAM02 Side by Side Whirlpool Refrigerator and from day 1 we have been having problems with rust buildup on both doors. Bought it in July 2014 and have had the service people over to figure out the problem many times. They finally decided to replace the doors which didnt help because the replacement doors are doing the same thing. We have bought everything they told us to buy to clean and try and prevent the rust from coming back but nothing helps. Our warranty was ready to expire so we bought the extended warranty only to find out that cosmetic issues are not covered under the extended warranty plan... Stay away from this model refrigerator... Not only that we were then told the doors are not really Stainless Steel just some fake crap that looks like Stainless Steel. We paid good money for this refrigerator and have to deal with cleaning rust off the doors day after day.

Big bang for your buck. I have used Whirlpool for years without any needed repairs. Typically you may see brands began to fade as you use them. However, the Whirlpool brand microwave always seem to stay true to its form. As long as you keep the inside clean the microwave should last a long time.

My Cabrio washer is 6 years old & has performed poorly from day 1. It does not clean properly so I have to rewash or wash clothes on a longer cycle (so much for energy efficient), it sounds like a plane taking off and has actually startled visitors, and it mysteriously forms sheets, towels & blankets in the shape of spare tire. This is the worst washer Ive ever bought.

My new washer quit working properly. It does not spin or wash properly.

In the last two years, the inner glass door of the oven has exploded. The last time was Tuesday, 14th January. The oven door was ajar because we had just finished cooking dinner. The noise was deafening but the worst thing about it was the large pieces of glass thrown all over the kitchen. Most of which were large enough and sharp enough to kill a child and seriously wound an adult. I phoned Whirlpool to report this. The operative I spoke to was very polite but told me these things happen and I could have banged it a while ago and left a weak spot! She also said a Supervisor or similar person would telephone me that day. It is now Saturday 18th January and NO phone call. MY concern is there is no mention of this being a possible problem in their literature and their obvious lack of concern under a Health and Safety situation. Not to mention the cost of replacement door glass.

We bought this combo at Lowes and was looking forward to their arrival. Unfortunately, we have had so many problems with both appliances. The washer is constantly having an error and we can only wash clothes on the quick wash cycle or else it will shake like crazy, get an error, and stop. We had the washer a little over a year when we had someone come look at it. We were told there is something wrong with the load sensor and it was going to be $350 to fix it. As for the dryer it will dry for a little bit and completely stop (no error) and restart later on by itself. I have been a devoted Whirlpool customer but not after this. I thought it was only us having these problems but obviously not. They have discontinued this set. No recall... ridiculous.

Yesterday I purchased this Whirlpool top load washer model WTW4816FW with agitator and we installed it at our vacation home and I started a small load to wash. Yikes, it made noises like a machine that is on its last legs. I knew from washing clothes for 40 years that this is NOT right. We, hubby and I waited and listened to this piece of junk to finish the cycle. Thank god I had set it for a short wash. We also videoed this contraption while it was grinding. I called Lowes and politely told them I was returning it. Thankfully they never had a problem with us bringing it back. (This must happen often.) I go back to the appliance department and decide on a Maytag. I noticed that it looked like the junk we just returned. I stood there and looked up the model number online and lo and behold there was a video of it doing exactly the same noise. It was virtually the same machine I just returned with just a name change. Needless to say we left the store washerless until I can research this further. I then found out that Whirlpool now owns Maytag. Thing is I just bought a front loader Maytag for my main home and it works good. It was a replacement for a Whirlpool without a agitator which worked well too. The YouTube videos seem to be washers with agitators doing this. I just wish I could post the video for all to hear. I guess we are all at the mercy of big companies who dont care if they make a good product as long as they can make it cheap.

I got a BRAND NEW Whirlpool from Habitat for Humanity. I registered it as a new product and was told it came from Lowes. Habitat only warranted it for 30 days but when it went out in 60 days, I called on the warranty. They sent out a repairman who said it was unfixable and after 2 weeks waiting to hear from them, Whirlpool said they would not honor the warranty because the serviceman said it had been dropped. I am a disabled senior citizen, I guarantee you I couldnt lift it long enough to drop it. Habitat said they didnt drop it and so did Lowes. Meanwhile, Whirlpool had the nerve to send me an extended warranty for the same refrigerator that they wouldnt honor the original warranty and they treated me like I was just trying to cheat them or something. The only thing I can do now is put it out in my driveway with a big sign on it to warn others NOT to buy Whirlpool products. Big deal.

I purchased my water heater at Lowes and had it installed professionally. I suspected something was not quite right on numerous occasions because the hot water recovery time seemed excessive. I finally called Whirlpool and they gave me the names and numbers of two companies that were on their list. The first asked for the model number and normal information and never called back. The second showed up spent five minutes charged me 78 dollars and said they could not get the part (gas valve) I needed. And if I could get it from Whirlpool they would charge me 250 to put it on. They also said Whirlpool made horrible water heaters and I should save myself the trouble and just replace it. I have since heard from additional plumbers and the gas company to stay away from Whirlpool. I did have the water heater replaced. When they did it and they drained the old water heater it had so much sludge in it draining it was very difficult. The sludge is mystery since I have a softener in my home and it should have prevented that. The individual from that gas company said that was just one of the many issue others had experienced with these heaters.

Agreeing with many. How disturbing to buy a Cabrio Whirlpool washing machine about 5 years ago. I might as well go down to the river and wash my clothes. The bearings went out which means I have to be the spin cycle. I am hanging out my clothes on the line - very wet - until my husband buys the part and fixes it himself. I had my maytag for 25 years. An awesome, dependable machine that we laid to rest because of rust. We should have gotten another drum instead of buying this machine. Where are the engineers that are making dependable appliances to last a LONG time? We have not gotten smarter. Or we only care about the all mighty dollar. Make something to last a short time so that you have to buy again. We will do some extensive research the next time we buy a washing machine. Do not buy this machine!

In less than 4 years my dryer had to be fixed twice as well as my washer. The dryer does its job. The washer is one of those HE washers that does not use much water. Clothes do not get clean without much water so I always need to set the washer on bulky to have water to cover the clothes. I wished I had kept my old washer. It worked a lot better.

Bought a model WRT318FZDW02 (top freezer) refrigerator (new) about 3 1/2 years ago and its already failing. The temperature regulation has failed and food in the lower compartment freezes while the temperature in the freezer compartment varies wildly. Unfortunately typical repair costs these days will probably make this a throw away item. Ive owned several different refrigerators over the years and theyve all lasted well beyond 10 years. I definitely cant recommend buying anything from Whirlpool these days.

I have the Whirlpool Gold microwave model GMH3204XVQ-1 manufactured in May of 2010. The plastic around the lower door handle is cracking (currently in 4 directions from the handle) and the plastic on the side of the control panel is cracking in the center area and lower side. Neither of these area experience abnormal stress in day-to-day use. Unfortunately I could not get a good photo of the other crack on the lower corner of the control panel but included the one on the side in the middle. I contacted Whirlpool customer support about 1-2 months ago and to date, have not received any type of response or concern from them about this issue.

We had to buy a new fridge in 2000 because ours broke. Following consumer reports, we went with a side-by-side Whirlpool gold and was it pricey! Within the first five years of its life, we had to replace the fan twice...the bar that separates the fridge and freezer could have fried an egg--it was so hot! When I had to replace it the second time, I pitched a fit to Whirlpool and they could care less! Now I see that the inside wall of the fridge section has cracks forming! I know the average lifespan is 10-15 years but I still will say that I will not buy from Whirlpool anymore! Their stuff is very expensive and it just seems it has too many small things that do not hold up!

I wish I had read all these reviews before buying this junk/lemon of a machine. Havent had the machine for a year yet and lots of problems. Only can wash five towels at a time and thats pushing it. Decided I would deal with it, until it gave other problems. First sometimes skipped cycles, then water came in when it was spinning. Called for service. Checking to see if we even can get you service in your area, representative says.About a week later tech comes and puts two parts in and left. Happy to get laundry going but, guess what??? Washes only doesnt do anything else and trying desperately to drain water out. Of course I have to take clothes out and bring to laundry. Tech comes back next day. Now he cant get any cycles to work either. Fried, tech says. Sets me up for next Saturday, fine.Now get a call on Monday, not coming. Tuesday is next appointment. Apparently inventory representative says. Didnt know that before??? Call Whirlpool, service first, then company. I want a new one, this is definitely a lemon. Nope, tech will be there on Tuesday. I hope Whirlpool reads this. They should be ashamed of their company. They used to be good, always bought their products. Dont buy these machines, trust me you dont need the aggravation. Totally disgusted.

Ours is a glass top & has 2 dual burners & we are very pleased with that feature. The oven however takes quite long to preheat & the alert sounds are so weak you can barely hear them. It was a rapid purchase on a sale item. I wish we had shopped a bit more.

While my oven was running the 3 hour self clean cycle, the glass on the inside of the door cracked. It was in the middle of the cycle so I tried to call whirlpool to see if I should hit cancel or if it would cool too quickly and make it worse or what to do. First person was young and stumbled with English in the service department. He couldnt answer my question, just schedule for me to pay for service to come out. After I got upset and said there must be someone to talk to, he sent me to parts who said she can only order me parts. All I wanted to know was was if flames were going to shoot from the oven or what! I told her that I needed to talk to someone who knew something about ovens and she asked if I was calling her stupid and hung up on me!

On its 1st year, the water pump went out. It cost $200.00 to replace it. On its 2nd year, the circuit board went out, and it took $300.00+ to replace it. On its 5th year, the bearings went out and cost $250.00 to replace it. I bought this for $900.00, and I already have paid $750.00 plus the price of purchase which makes this washer $1,600.00. Whirlpool should compensate all of us who have worked hard and have purchased this product! I will never purchase from Whirlpool again. I can’t afford them. I should get a refund from Whirlpool. Don’t they care? Email me for these problems at **. I am so dissatisfied with this product.

Whirlpool fridge with ice and water dispenser that broke down within days of install. The water dispenser stopped working after the first flush and Whirlpool were notified. They engaged a useless repair company who have been unable to resolve the problem and will not communicate updates. Whirlpool have been fully informed of the problem with their brand new product which was defective practically from the start and have washed their hands of any involvement in resolving the problem with their appliance. They defer defective product as a warranty issue and leave the consumer to chase after people to get a repair done. For a brand new $3,700 fridge that doesnt work within a week of install I just cannot believe they would sell a defective item and make their consumer suffer for it.What consumer would knowingly choose to purchase a defective appliance? If you end up getting a defect, the company should make it right....right away. Im at 2 months now without a functioning water dispenser on a fridge that is only 2 months old. Just disgusting.

I bought a brand new Whirlpool washer and dryer set -Cabrio- $1700.00 in 2011. It is by far the worst washing machine I have ever purchased, and I am 60 years old!!! It is now three years old and has been repaired at least 4 times. Long story short... after hours & hours on the phone, along with many threats! (By the way I had to ask for a manager two times up the ladder for this to happen as they just kept repeating that it was out of warranty coverage). I also told them that I was going to have one of my company trucks deliver this machine to Sears lot, along with a paid person to inform every shopper of my plight with this washer and the lack of service from Sears and Whirlpool! Whirlpool finally agreed to pay for the parts but not the labor on this most current repair. (This time it is the transmission!! In the past it was the Hub, twice. The gear case twice and the belt a number of times). I am now going back to Sears to request (that might not be the correct word) Demand, that they take care of the service bill for this machine. In between repairs, I have dealt with ongoing cleaning quality problems. This machine does not get clothes clean. I always have to wash them twice. This machine is loud. This machine does not use enough water to even dissolve the soap. So much for energy saving measures when you have to wash twice and still see soap and crud in the tub. Worst, worst, ever washing machine in my life!! By the way, I have an 8 year old Maytag too that I have never had to repair. Moral of the story, buy Maytag, or at least do not buy a Cabrio!!!!

Our Whirlpool refrigerator was delivered July 27th, 2013 after waiting 6 weeks for it. I was getting something off the top shelf (side by side refrigerator) when a 2-liter plastic bottle fell and put a hole in the bottom shelf where it sticks out under the vegetable tray. I have had grandkids sometimes stand on that shelf of our other refrigerators without ever doing any damage to it. It makes me nervous of dropping something else. I would like to send a complaint directly to Whirlpool but dont know how to reach them.

Worst refrigerator Ive ever bought. Previous one still perfect shape. 22 years old. Freezes everything on top shelf. Motor making grrrr noises. Had repaired. Now bottom crisper drawers so cheap the plastic is breaking. Drawers wont slide. Now Deli tray lid snapped in half! STAY AWAY from this USA made product.

I purchased the Whirlpool Cabrio Washer WT5500XW2 from Lowes on 9/12/2012, which turned out to be the worst purchase of my life. It did ok for over a year. It had always been noisy. Now it sounds like a jet airplane when it is on the spin cycle. This machine is not yet 2 years old. Do not buy a whirlpool washer. They are Junk. Plan on getting rid of this piece of junk and buying a new washer. Dont waste your money on Whirlpool!

Called Whirlpool about fridge and they stated Too bad its out of warranty. The sides are getting pitted. It is a stainless with black sides. The condo is always air conditioned. It is two years old. Not very long to have a $1200 fridge look terrible. However, the fridge works fine.

It took 5 deliveries to get a fridge that wasnt damaged. First two came from Leons - the same damage on both. Then they said we had to go through Whirlpool because so much time had lapsed. We had purchased the full set of Whirlpool Gold for our kitchen renovation; therefore, we were unable to unpack the fridge until the cabinets were completed. I phoned Whirlpool Canada, and they said they had to send a service tech. The service tech came, and he confirmed the damage and was told to patch it with a proxy. Sorry but I had just paid $1500 for a new fridge. I didnt want a dent and damage. We received no offer for discount to accept the damaged fridge. They sent another one, still damaged. They used their truck to deliver and the guy had no idea how smashed our brand-new trim.So Whirlpool sent another fridge, and even though I asked them to check it before sending, they didnt. It was damaged. This is four fridges. Im tired of fighting with Whirlpool. I called Leons, and they take care to get me a new fridge undamaged. I told Whirlpool about the damage, and they sent a form. First, they wanted me to claim on my house insurance. Why should I put on a claim? If not, get two quotes and fill out tons of paperwork. Im just too tired after fighting for over two months to get a fridge that isnt damaged. Not even an offer of compensation to cover all the time taken off work and the stress on me and my family. This is the second set of Whirlpool Gold we have purchased in the last 4 years. I doubt I will ever purchase again, because you are a company that doesnt treat your customers with respect or concern.

I purchased the Whirlpool Duet June 2011. Within two weeks, it was tearing my clothes. It didnt matter how little of a load it was, they still ripped. Five months later, my machine was leaking water. The repair man came out. I told him it was also tearing my clothes. His only response was dont load it to full. Well, I called the store where I purchased it and they are sending a repair man out again. I told them to either fix this from ripping my clothes or I was going to take a hammer to the machine and never buy a Whirlpool again or give them a good reference. I also called Whirlpool directly and told them of my problem and they acted like they had never heard of this happening before. I told them to search the internet because everyone is having the same complaint! I had a Fridgidaire front loader for 9 years and never had a problem with it eating my clothes.

This morning is the fifth morning I had to take a cold shower. My hot water heater keeps going out. When we call, we are told to dust the underneath better, as it sucks dust. Are you kidding? The hot water heater is still under warranty, which means I will have to spend around $200 to have repaired again. So much for top of the line.

We purchased our home in 5/09. Within a month, we had to replace the defective gas valve due to inefficient burning. Our house smelled like gas each time we used the oven. It was under warranty at that time so Whirlpool replaced it. It is now 5/12 and out of warranty. We called a local independent technician who informed us the oven wouldnt turn on due to another issue with the gas valve, the same one that had been replaced shortly after we moved in. He went to his local supplier to purchase the gas valve to be informed that they couldnt seem to keep this particular gas valve in stock, simply because its a reoccurring known issue and Whirlpool needed to do something about it. So, this technician encouraged me to call Whirlpool. I called the 1-800 number, spoke to 3 different people and was constantly informed that since it was out of warranty they would do absolutely nothing! Again, I was informed that this gas valve is a reoccurring known problem with Whirlpool so perhaps they should consider looking into this issue. The last person I spoke to was a bit snide and just kept saying It is past your warranty, we will do absolutely nothing to help you, and sorry you are having that problem. We are not aware of this reoccurring gas valve issue. Have a good day!” Whirlpool, do you understand your reputation is at risk when you dont want to stand behind your parts that should work after 3 years! Should a brand new part not work properly after a month? Should another service call have to be made after 3 years? Sounds like a quality issue, something Whirlpool needs to investigate especially after a local supplier states they sell this particular gas valve all the time due to a reoccurring issue.

Our 2005 whirlpool duet washer steel drum and plastic tub broke. My husband diagnosed the problem and opted to fix it to save money. The parts are under warranty but you still pay labor and technician visit running up to $250-$300. The plastic tub was obtained only if we paid for it $100 and the steel drum they sent under warranty. The plastic tub has a hole with a black plug and sensor in it. There is a discrepancy in the measurement of the old tub and new tubs hole that is slightly larger, therefore when installed a steady stream of water leaks out. I now have 3 plastic tubs as that was their solution, to send more of the same that did not measure correctly. An investigation was done to determine they were the correct parts. As asked we had a whirlpool technician come to verify parts were correct and being installed correctly and the parts sent would not fix the machine due to the hole discrepancy. Many calls were made to whirlpool and they continue to give me the runaround. They now are not taking their technicians information. The technician has given the information to 3 sales reps in the new england area and made several phone calls to whirlpool and no one is willing to give us a solution.

About 29 Nov 2011, I bought a Whirlpool microwave, which model no. is magic cook 206 (mech). Sr No. CNF103400315, when we bought this item, we asked for the start up kit, but at that time they said that in grill microwave we dont provide start up kit but after a month when I again raise for start up kit, that time they give but in start up kit some item is missing and the sealed is open. So I kindly request you to take some action to the shop.

We bought a new house and the choice given to us was Whirlpool. After the first year in the house we had a $300 repair. The control panel inside the fridge went. Pretty poor performance.

I bought a Whirlpool refrigerator side by-side model #ED2PHEXMQ00, made in 01/04. As I was letting my dog out at 4 am, I heard a sizzling noise and I immediately smelled an electrical burning odor. I lost all of my food, but thankfully I caught it before it caused a fire. Had this happened during the day, I would have lost my 3 dogs and my home. I had to borrow a mini fridge for the time being because I dont have the money for the repairs or replacement. Since this is an ongoing problem, Im not sure replacing the part will make me feel confident in trusting that it wont happen again. I may not be as lucky to be standing next to it if it does happen again. Whether its under warranty or not, Whirlpool should take responsibility and issue a recall and replace the parts. I would never suggest buying a Whirlpool product in the future.

We purchased our Whirlpool Cabrio platinum washer about 3 years ago. I am completely frustrated with it. When it is on spin cycle, it sounds like a freight train going through my house. During the rest of the washing... it squeaks. And right now this is the 5th attempt to wash the same load of laundry. Because it keeps getting unlevel and it will not continue after I move the clothes around to get it level. So I have to start all over. There is not a spin cycle option that is available by itself. Every time I have to choose the rinse/drain/spin option. Obviously it is not under warranty anymore! Only a one year warranty... really pathetic! And when we called they offered us a little discount to buy another one. No thank you!!! Wont ever buy Whirlpool again.

On the 27th March 2012 I bought a new Whirlpool 6th Sense washing machine S/N 411048002028 AWOE 9210 - 30 9Kg for E499.00. I brought it home and plumbed it adding in a lime filter on the water line to protect it from limescale. On the 14th September 2016 a service technician replaced the entire drum as the old one made so much noise and the ball bearings are part of the drum. On the 7th June 2013 a technician replaced the drive belt claiming that it moved if a light load was put into the machine. On the same day I added an extension of 3 years Guarantee at Euro 89.00. On the 14th October 2013 a technician examined the machine for a water leak but found nothing and charged me for the call. Out E25.00. I lived with the noise of the spin cycle ever since. The noise got steadily worse until 27th September 2016 when the machine finally packed in. I stripped the machine down to find the ball bearings on the drum completely rusted over so the drum was rotating without the cushioning. On the same day I bought a Bosch machine and decided to forget about the extra guarantee as the offending parts had already been replaced once and did not even last 4 years. I will bring it to the recycling yard later today as that is all it is good for. It was bought in Media World, Orio Center, Bergamo. It was paid for by Gianni ** who is my father-in-law and had a loyalty card for the shop.

We bought a top loaded Whirlpool washer, model WTW5000DW2 last May from Lowe’s for a summer beach cottage. It has been a terrible experience. There was a 30 day warranty from Lowe’s which unfortunately we missed because we had not moved down for the summer till after the 30 days. Working through Whirlpool, they sent an independent contractor out 5 times over the summer. Control panel was replaced twice. It never worked properly. I’m now back for the summer, and it still does not work. Do not buy this washer.

We bought the Whirlpool duet washer & dryer in the winter 2011. The washer is absolutely awful. I have to keep it set on the Whitest White setting so every load gets a second rinse. In order for my clothes to smell CLEAN I use bleach in every load I can. With the loads I absolutely cant use bleach in, I have to be standing waiting to put the clothes in the dryer or I have to rewash the entire load because of the smell!! My towels are ruined from the bleach and my clothes are faded because of the multiple wash cycles. I have used the recommended Affresh numerous times and it does not help! Needless to say this washer was a total WASTE of money! We will be purchasing a new washer very soon! It will NOT be Whirlpool!!

Best stainless steel built dishwasher we could find in this price range. Well built with lots of room and easy access to both drawers. Easy to clean filters and a nice modern look.

Just bought the Whirlpool 3.5 cu ft, Top Load HE washer (model WTW4815EW), but of course, the sales person did not explain that HE meant LOW WATER USAGE. Wish I had done my homework. FIRST LOAD, clothes seem to be beaten to death, and must pour in detergent before you load clothes. So, Oxyclean detergent I always used in my regular (NOT HE) washer put a hole in one towel and discolored (faded out) the others. Also seems that the fast and hard agitator would not (logically) last very long. It seems to be working very hard. Im SO disappointed. Called Whirlpool to say I dont like it. They said to call Home Depot and see what they will do about an exchange. When I did, my sales person said that almost all the washers he sells are HE. I want the old type washer back that allows me to add more water if I want, change the cycle and water levels at my discretion, add detergent when I want to, and soak clothes if I wish.

Our Whirlpool Duet Washer pair is 2.5 yrs old. The washer didnt work at first, but a repairman found the problem and fixed it right up. They have not broken. The dryer has been fine and we have had them stacked for most of the time without any issues. My problem sounds minor compared to those others listed here, but this thing is ruining all our white or light colored clothes. They go in white, and come out covered with splotchy, dirty looking spots literally all over them! They werent that kind of dirty when they went in. It’s the oddest thing, like it makes dirt. Reading some of these concerns makes me wonder if it has a mold problem inside somewhere, and that is what is ruining our clothes. Tax return is coming and it is going. End of story.

We just recently remodelled our kitchen and decided to buy a Whirlpool Range. Big mistake. First off, the range was advertised as a built in but it ended up looking like a slide in. We were disappointed but decided it was ok as long as the range performed fine. However, within 6 months of buying it, the oven fan broke and the oven became unusable. I used it only 2 - 3 times before it gave up. Extremely disappointed. Our old oven was sturdier and lasted many years and was in a very good condition when we gave it away. Extremely disappointed since we paid a lot for it.

This Whirlpool washing machine is incredibly annoying and slow in everything it does. First off when you press the START button it takes 2-3 minutes before it decides to do anything, like maybe add water (except click, click and more click). If you have pressed the start button and you want to stop it to add something... again you have to wait almost 2-3 minutes before the lock is released and you can open the door. I am at 2 hrs and 15 minutes as I write this on the LIGHT WASH cycle with extra rinse and its still going. I have never seen anything like it. Cant imagine how long a HEAVY CYCLE takes. Cannot even try to measure the time. I put the load in and go to work and hope its complete when Im done 8 hrs later.We had a Maytag for 15 years with no issues (other than a drain hose cracked and had to be replaced) and it was time for a new one with a move to a new place. The sales associate convinced us this was the best machine at the time... Well what a mistake that was. There are no complaints about the actual washing. Everything comes out clean but I suppose taking that long I cant imagine why it wouldnt. I certainly cant recommend a Whirlpool washer to a friend, because I dread the thought of doing laundry at this point.

After 2 years it stopped draining. We have to physically hit cancel to get it to drain. Also, I have had to make my own tool to take bottom spin bar off to get to and unjam grinder and we pre-wash all dishes.

Ive had the WDF510PAY dishwasher for 3 years and the circulation pump broke. To be more specific the impeller inside the circulation pump warped and then basically got lodged because it became oblong and then it wouldnt pump water to the spray arms etc. I bought a new pump because the warranty only last a year. The pump cost around 90 bucks. After not even 1 full year this factory replacement pump failed again. I reviewed other Whirlpool dishwashers more expensive and I found they all have this same junky circulation pump. Im not sure of a better dishwasher but I would never recommend a Whirlpool dishwasher again. They also use the same circulation pump in Maytag and many other brands. Whirlpool or whoever designed and sold this pump to Whirlpool should be tracked down and beaten. Simple products like dishwashers should last more than 3 years. The technology is nothing new. A product should last 10 years at least.

I call in to Customer Service to get someone to fix my washing machine because it wasnt working and when I called, I forgot to have my washing machine serial number at hand. The person on the other side told me that she cant wait for me to get the serial number more than 2 minutes and I ask myself, if they cant wait for me more than 2 minutes to get my serial number, then why should I wait a week to have someone fix my washing machine?

Despite always using the designated (he) detergents and trying many different brands in appropriate amounts, this washer always leaves an ugly white residue on clothes. This happens all the time, requiring whole loads of clothes to be rewashed, sometimes more than once. This defeats the whole purpose of conserving water, which is reflected in our water bill. We also placed the laundry room on the second floor to make it easier for me with my disabilities. I am constantly having to climb the stairs when the machine gets unbalanced in addition to the extra loads from the residue. I was very excited to purchase this machine. Unfortunately, these feelings didnt last long.

I would say that the Whirlpool refrigerator is overall satisfactory and a good product. The size accommodates our refrigerator needs. Would recommend product to my friends and family.

I was so excited when I bought this stove. It broke right outside the warranty. It shuts off in the middle of baking or just doesnt stay on at all. Bad, bad, bad. They told me it would cost $400 just for the part, not including installation. What a rip off. I called the tech and he said this is a known problem. He advised me to just toss it and buy Hotpoint which has a much better consumer report rating. Sad.

I bought Whirlpool hot water heater with the Honeywell part in 2014 and the thermal box went out. No flashing lights, no way to reset. I understand that Whirlpool had a class action lawsuit after researching. Still selling this product to consumers. Whirlpool should be held responsible, and be made to give an allotment to replace homeowners with hot water tank of choice! If lawsuit is active please add my name.

We use a Whirlpool Washing Machine and it is one that came with this apartment provided to us by our employers. My parents had a Whirlpool Washing Machine too and they have had no problems since I have known them to use a Whirlpool. The Whirlpool that we are using has been very reliable in the past 3 years we have been using it. No issues whatsoever! The clothes do come out clean, so it does it's job! It is a top loading washing machine as opposed to the newer front loading ones. I have not used a front loading washing machine, so I do not know how it compares to them. The settings on our Whirlpool are basic and very easy to use. (If you know what you are doing, of course). LOL! Reliable is the word for Whirlpool!!

Whirlpool gas range model WDF560SAFT bisque color, purchased in June 2020 from Home Depot online. After a 3.5 month wait range was delivered September 12, 2020 and installed. Have used the oven less than 5 times. Standing in my kitchen yesterday and heard a pinging noise, noticed chips of the finish all over my floor, it was chipping inside the top of the oven door, overnight the exterior top of the door was also chipping, bits of finish flying all over my kitchen! Have been on hold with Home a depot Cust. Serv. for almost 60 min. Will attempt to return to a Home Depot. Not sure what to do short of complaining about lousy Whirlpool product. Next time will come to Consumer Affairs and research.

Whirlpool Cambridge Model #WTW7300DW0 - Someone needs to help us consumers with this wash machine purchase being refund our money back from Whirlpool. It literally eats my clothes. I have 23 shirts that have pin holes in them and 1 shirt with large holes in it. I also have a ruined comforter and blanket. The comforter has soap stains everywhere which dont come out so its not cleaning the clothes, the blanket (which Ive had for over 30 years) was frayed one side, seam torn off - the piece never came out of the wash machine. I have pictures attached of the damaged. Its suppose to be Water Efficient - thats a joke! I do 1 set of king sheets. It runs for an hour and 20 minutes and fills water to the rim of the washer and does this twice. Id like them to pay for my water bills! Oh they came to service it only to tell me I was putting the clothes in wrong. The service company said I had to put the clothes against the sides and leave the middle open. They told me there was nothing wrong but consumer error. Well I did clothes today and aligned them like the service company said - 4 more shirts were ruined. Called Whirlpool today. They said they were sending someone else out to fix the problem and said, Unfortunately, we dont pay for damaged goods. Well from all the reviews I read Whirlpool needs to suck it up and recall this piece of crap they call a wash machine. Did I mention its only 1 year old, yea this is horrible!

I have a Whirlpool french door unit with ice & water through the freezer door. I recently noticed rust in the ice. When the extended service plans tech came to see it he told me that the ice bucket would have to be ordered. Almost a month later, I called him and was told that rust isnt covered. I understand that surface or cosmetic rust shouldnt be covered, but rust in a place where it can be ingested is different. Anyway, I called Whirlpool directly and a very nice phone rep agreed with me and asked her supervisor. Needless to say, I just sent Whirlpool a letter stating that I would pursue this through legal channels if I dont get satisfaction.

I purchased an HIE washer one year ago this month. I have never been happy with the cleanliness of the clothes when they came out of the wash. The only way to get them moderately clean is to wash a few items at a time and even then the whites, especially socks, seem dingy. I noticed the new Whirlpool washers now have an extra setting to add more water to the machine, so the executives have realized there is a problem with the original model.I think Whirlpool should give all customers who previously purchased the models without this feature a trade-in option to get the newer model that fills with more water or for another model with the full spindle that has worked well for so many years. I have been very unhappy with the performance of this washer and would only hope the executives would do something to resolve this problem and satisfy previous customers.

I just finished a call with Sears Repair. I informed them that this was the 5th service call since purchasing this Whirlpool Cabrio washer two years ago. The washer simply does not work. It fails to complete its cycle; fails to spin; fails to drain; fails to fill; leaves clothes streaked and dirty, smelly, and dripping wet for me to wring out by hand. I purchased it because of my faith in Sears and its Energy Saver label. I often have to wash the same load 2 or even 3 times to get it clean; no more than 6 towels at a time. (It is a large capacity washer, but acts up most often when washing towels or jeans.)Im a retired teacher; and in my best teacher voice – calm but serious – said that I would like Sears to come and take it away, issue me a credit or refund, or I would proceed to file with the Small Claims Court. His immediate response was, I dont appreciate the threat. I carefully (teacher voice) explained that it was not a threat... it was information. Yes, Im angry. But more than that, I am so disappointed in Sears, a company that I have always been loyal to – no more. Time to leave childhood behind and wake up to the reality that this is not the same Sears Ive dealt with for the last sixty years. Now, I’m to drive 25 miles of country roads to a Laundromat.

I bought the Whirlpool Gold Series dishwasher on November of 2014 from Home Depot. The first thing that happened was that it started to leak. I called Whirlpool and someone came out to look at it. It took about a week for them to come. They said it was installed incorrectly and they do not handle installation issues. They left. I took the dishwasher out and reinstalled according to the guide. It still leaked. The dishwasher had to be perfectly level before the leaking stopped.The next issue was that the dishes were not getting clean my dishes. The top rack was the worse. I called Whirlpool again. They came out, took the dishwasher apart and said the part called the diffuser had become dislocated. He placed it back into its proper position and left. This was April of 2015. The dishwasher did an ok job. Some dishes still came out with food on it. By the end of 2015, close to the warranty expiring, the top rack was no longer being washed. I took the dishwasher apart from the inside and found the diffuser was not in the right position again. So every time I want to run the dishwasher I need to take the spray arms out and the racks until I have access to the bottom of the dishwasher to reset the diffuser. Now the warranty was expired, Whirlpool wanted about $150 just to come look at the dishwasher. Sears wanted $59. So I called Sears. Their tech said the dishwasher has a broken motor. For Sears to fix it would be around $400. I called Whirlpool. I felt that the motor was already broken within the warranty period and that the problem finally got diagnosed now. Whirlpool felt this wasnt the case. Their price to fix was also close to $400. Now I need to buy a new dishwasher and throw away a one year old dishwasher. Only this time I will buy the extended warranty. Overall, poor product, poor customer service, and poor warranty coverage.

I purchased a front loading Whirlpool washing machine March 2017. I have need to have the drain pump replaced and the motherboard replaced. Each repair took 30 to 45 days to get parts and service. I would not recommend the washing machine.

Whirlpool WFE720H0AS0 - I tried to use the self cleaning oven feature and it cleaned the bottom of the stove but did nothing for the sides, back and door of stove. The top of the stove is impossible to keep clean. Maintaining this appliance is a full-time job. Very bad choice.

I purchased a Whirlpool microwave model #WHM3205XVS1 on October 2, 2011. The handle broke off in little pieces and was repaired in March 2012. Handle broke off again in little pieces in September 2012. This will be the 3rd handle that will continue to break in little pieces every 6 months. According to both repair men that were here, this is their comment: No customer abuse, this is a very common problem with this model. After to speaking to 3 people at Whirlpool, I was told by everyone, This is cosmetic problem and we will not fix after the 1 year manufacturers warranty is up. I started with the the first person, went to her supervisor, then went to her supervisor. I am now waiting for a call from a manager although I was told I will continue to get the same answer no matter how far up the chain of command I go. So, I was told that it is okay to have 2 screws sticking out holding the remaining part of the handle that is left, because it is a cosmetic, not a functional problem. I will never stop with Whirlpool. I will call 4 times a day if necessary. I will never purchase another Whirlpool product again! I will tell everyone I know not to purchase one of their products. Be careful. They manufacture products for many other companies, i.e., Sears, Amana, Jenn-Air, and many, many more.

Ive had trouble with my washing machine since the end of May 2011. I have had over 5 service/repair calls which still resulted with the same problem. By the way, I do have a warranty on this product (which hasnt seem to have helped at all). I have never had such poor customer service in my life as I have had from Sears and can assure you, I will never buy another product from Sears or Whirlpool considering the experience I have had. I have missed numerous days at work only to wait for a repair appointment that never happened. Needless to say, I am very disappointed and would not recommend anyone to buy from Sears or Whirlpool.

17 month old Whirlpool duet washer door lock broke. ($300) repair! Had given my old (13 years) set to daughter when I moved. That set has never had a repair or problem! Why do they keep making things with more bells and whistles we dont need and so cheaply made? Frustrated, annoyed and becoming cynical in middle age.

I bought this stove 4 years ago from Lowes. I have had nothing but problems ever since. My family is now afraid to use the stove and Whirlpool refuses to stand behind their product. The last straw was a bill for a service call that took 6 months to complete without correcting the problem. Whirlpool sent me a bill for $100 to pay for the privileged. When I complained, WP said if I paid the invoice, they would give me a deal towards a new stove. Meanwhile, the old stove does not work and we are afraid to use it, given our experience with its reliability and safety. I plan to return it to Lowes and buy anything but a Whirlpool product. Beware of Whirlpool Maytag anything!! The customer service is shameful!!

I waited years to buy this machine. I hate it!!! I agree with the other bad reviews. It destroys clothes. There is barely enough water in it to cover the bottom of the machine much less the laundry. Even deep water is a joke. It does not clean. I put it on the hottest water temp and I can put my hand in there and it is barely warm (it is not my hot water heater). My lightweight comforters come out all tacky and grungy in the middle. The softener dispenser (I use vinegar) dumps in the laundry (no it is not over full) (no I do not slam it shut). I can not let anything soak because the machine will drain after a few minutes and all my detergent, scent crystals etc. are all wasted. I feel like I have to take a survey and complete a questionnaire every time I do laundry. Can someone tell me how to put a comforter in there and leave that little middle eye open? They say the water saver is government regulated? Yup I need the government to do my laundry... I believe in saving water. I have a water saver toilet, shower, faucets. However I can not clean dirty jeans in a gallon of water. My clothes do not even get wet. How does whirlpool get away with advertising this machine can do king size comforter? The gentle cycle will tear apart anything I might put in there because there is no water and that blooming thing just twist and turns so it tears anything delicate. This is the 21st century. I think I should not have to babysit my washing machine. Why should I have to readjust everything in hopes it might be almost clean??? Place this here and that there, wipe the lint out before doing dark laundry. This machine belongs in the dark ages. It is so complicated yet it achieves nothing. A big rip off. I so tired of crying over this purchase. I hate this machine!!!

I purchased a Whirlpool Cabrio in 2009. It worked so-so over the years but recently stopped completing cycles, citing false load balance errors and leaving towels and sheets sopping wet at the end of a cycle. Three repair appointments later, and still no success. I am thoroughly disgusted that such an expensive machine only lasts four years. Based on the service techs attitude toward the machine and other consumer comments, Im guessing I will have to replace it. You can guess it will not be with a Whirlpool machine!

Whirlpool Cabrio top loader washer - I am writing to really complain about a washer I bought there at Metro. The people were great BUT this washer has been a REAL DISAPPOINTMENT!!! It is only 4 years old and I have had to have them come and replace the top of the machine. It has rusted around where you put the bleach, the soap. It leaks underneath the machine, its rusting on the bottom of the machine horribly. SO DISAPPOINTED!!! We bought all WHIRLPOOL products - washer and dryer, stove, microwave, dishwasher.What is it with these things? They rust so easy. I had a washer before this one for 14 years and it never did this. I guess things are not made with the same quality as years ago, but I will not ever spend my hard earned money on WHIRLPOOL AGAIN!!! I guess I will have to put up with this machine till I can afford to buy something else. VERY DISAPPOINTED CUSTOMER!!!

I have a pretty small refrigerator since I live in a condo. It has lasted me about 4 years and is still running very well. It is very easy to clean. I dont buy a whole lot of food at one time. The size is big enough to hold what I buy every week. The appearance is decent. Only two people use it every day. I havent had any problems with the refrigerator in the four years I have had it. I get frustrated sometimes when opening up the bottom storage container. If I pull it out too far, it falls to the floor. This happens especially when the container is full of fruits and vegetables. I guess bottom storage container was designed that way for easy removal to be cleaned. I really like the adjustable shelves. I can adjust them perfectly to store food containers and jugs of milk and other drinks. I like the door shelves in the freezer compartment. It is great for small packages of vegetables.

Absolute garbage!!! French door refrig/bottom freezer. Too much to go into. This is by far the worst product that I have EVER purchased in my life. If I was strong enough to lift this piece of ** over my head I would carry it into the corporate headquarters of these money grabbing dirt balls and throw it through the CEOs door. Amend that: I would locate customer service and consider them bowling pins. What a bummer; how far we have fallen!!!

I have had this refrigerator for over 25 years and cant ask for anything better than that. Would buy another Whirlpool refrigerator. Has original french doors at top and bottom door on freezer. However, I dont particularly like the pull out drawer that the new refrigerators have now as I get so much more room with a door. The new refrigerators have improved rubber around the doors. That is the only thing I had to replace on this refrigerator.

I purchased a Whirlpool dishwasher and refrigerator/freezer from Home Depot. Within weeks the stainless steel on both products began rusting. They sent a third party repair service to look at both products and determined that, in fact, the stainless steel was rusting. Our technician said that both the dishwasher panes and the freezer doors would be ordered and replaced the following week. This was on September 4, 2015. After several promised arrival dates, the parts never arrived. I called both the third party repair company and Whirlpool on several occasions only to be told they were on back order. Finally, in late November, the new dishwasher panel arrived and was installed. It is now December 17, 2015 and our freezer door is still on back order. When asked what my options are, the Whirlpool representative simply said we have to wait. I said that because I have been so terribly inconvenienced that they should just come and pick up this piece of junk and replace it with a new one. Evidently, that is not an option. I will NEVER purchase a Whirlpool product again as they do not back their warranty. I now have a $2,000 rusted refrigerator freezer to adorn our beautiful Christmas kitchen. Thanks, Whirlpool. Youve certainly made this a Merry Christmas. (Yes, sarcasm in play.)

We purchased the Whirlpool double oven gas range from Lowes in July of 2014. The oven heat that boils out onto the stove top when you use either oven makes it difficult to handle the pots on the range top. The first time I used both ovens at the same time the plastic front to the control panel started to melt and the fumes were horrible. It was under warranty so Whirlpool replaced it with an identical panel that also melted when I used the top oven and range top at the same time. Its out of warranty so Whirlpool says its not their problem. From reading these other complaints it is obvious to me that customer satisfaction is not important to Whirlpool - just that profit margin. Build cheap - sell high should be their motto.

Whirlpool washer Model WGD4815EW1. Bought this washer just about 4 months ago and right away I hated it but was told by people that all the machines had gone to the lid lock and that the government had mandated the energy saving devices on the machines so the machine will only put just a little water in the machine. I have been VERY VERY unhappy with this machine. My husband figured out a way to bypass the lid lock mechanism. Then after washing clothes many times I found out in order to get my clothes clean I had to just set the dial to Bulky every time OR I had to wash the clothes 2 times to get clean if I didnt. Once we bypassed the lid lock and then I figured out where to put the knob so the clothes would come clean I was fine until last week the machine just would NOT wash or do anything... it filled with water and just sat there until my husband got the water out. I located a Speed Queen from an appliance store and I am much happier. It does not have the CRAZY lid lock on it. I realize that some children are apt to mess with the washers. But I dont have children anymore and when I did I had a laundry room with a lock up high on the door so they could not play in the laundry room. I dont understand why this so called mandate could not have been done in a way as to allow those with kids to have the option on the machine with a built in code device to set the machine so the lid will lock and those of us without children in the house to opt out of the code to set the lid lock. NO REASON why we cant have a CHOICE. As far as I see it is a way for the government to try control more where they need to keep out. The cars have been designed with safety locks for children to keep them safe, but it is up to you to choose to use them. Same principle! Now for the mechanism to make it so the machine will only put so much water in the machine to wash. Youre NOT SAVING any ENERGY or WATER if you have to wash the loads twice!! This whole mandated business with the newer washer machines is a huge JOKE on everyone. I will be searching out used machines and having them rebuilt because I dont EVER plan on buying another one of these newer machines. If enough people stop buying them the manufacturing companies can raise some cane with the government to get the mandate lifted. NO I will not buy another Whirlpool washer. I encourage some of you out there who LOVE a challenge to figure a way to change the stupid motherboards on the newer machines and create a great business for yourself because if someone else can create it you can recreate it.

I have spent 30 minutes trying to change light bulb under the oven and get the cover plate back on. I watched the film on how to do it, it was amusing to watch the struggle to get it on. It was amusing to say the least. Whirlpool watching it??? I do not believe whoever designed this worthless time consuming light cover never tested it one time, or it would had been more user friendly. It amazes me what kind of trash they can build for us consumers to have to deal with at times. Tomorrow this overhead piece of junk is coming out and being replaced by a non Whirlpool one. I am going to get a tractor and smash it into little pieces and put on side of street with a note saying this is what happens when you try for an hour to change the bulb.

I purchased my new Whirlpool Cabrio Top Load washer to replace a Maytag that had finally given out in the summer of 2012. I wish I did more due diligence, but with a toddler and a newborn, I needed a washer asap. I severely regret my $800 purchase from Sears. It is now February 2013 and the machine basically only runs on two cycles - Casual and Normal. All the others stop in mid-cycle. Sometimes, the items are still dry or partially wet so I need to switch to another cycle to complete the wash. This is not good for Delicates or when I wash Whites, Heavy Duty or Bulky items which is one of the reasons I purchased the model. The cycle stops when the items are soaked with massive amounts of water. So I then have to turn it to the Drain cycle and start over. After a day of washing one load, I couldve done it the old-fashioned way in my utility basin sink and hung it out to dry ... I dont have the time for this. I am going to make a formal complaint to Whirlpool and to Sears. I cannot keep spending nearly $1,000 for items that break within a year. These companies should be ashamed of their lack of quality. I shouldve gone with the Electrolux and just dealt with the price tag - I wouldve been much happier.

It is a new model side by side with water and ice maker. The temperature is very uneven, inside it has surprisingly little storage room in both fridge and freezer. Very difficult to fit food in due to awkward spaces. Would not buy again or recommend.

I purchased this machine three years ago. It is junk. I have had two washing machines and they lasted for years and years. Never had a problem with either machine. I purchased them from Sears. When I the Cabrio, I was told it was the top of the line washer for Whirlpool. Three weeks ago it started making a noise like a plane taking off. It wouldnt spin the clothes. The repair person said that it could be three different things the parts, for which, would cost in the vicinity of $200. However, since it was making such a loud noise and water was coming out from underneath the washer, he was certain the transmission was out. He said the noise was an indicator the bearings were gone. I didnt see much point in repairing the washer if the transmission was out because it couldnt be fix.There was a couple at Lowes purchasing a machine at the same time as myself. They said they had a Cabrio also and it was only two years old. It wasnt spinning the clothes either and making a tremendously loud noise. They told us this before we mentioned that we had a Cabrio also. I will neither purchase another Whirlpool product. Junk!

Bought this machine in Feb 2007 as a pair Whirlpool Cabrio. I loved it for almost two years. The control board went out, Whirlpool replaced it. A couple of weeks later, the F-1 codes started then the F-51 codes. On July of 10, it was code after code. It sounded like a jet taking off and constant unbalanced load. I called repairman and was told to go buy new machine as repairs would start at $500 and since I live in a rural area, no one wanted to waste their time. Two repair techs told me point blank they wouldnt even touch it. We paid $1000 for this machine and we live pay check to pay check. I spent four months trying to get Whirlpool to do something. I kept getting told I should have bought extended warranty. Machine has been sitting under stairs for over year waiting to see if class action or recall can be done. Also when control board was replaced, the repair man told me it was rusting away from the inside out. My husband had to find us a used washer and this thing has done nothing but cost us money. So much for efficiency. Everyone posting here also needs to go to Whirlpools Facebook page and post there.

The appliances in my home range from a Kitchen Aid double wall oven, a DCS single wall oven (I have 2 Kitchens), 2 Kenmore dishwashers, a Fisher and Paykel refrigerator and 2 DCS counter-top stoves (all top of the line). No problems they are great appliances. On Dec.22, I bought a Whirlpool Duet. For 6 months, constant repairs and rebuilds were needed; new computer panels, pumps and new drums. They cant fix it. We have tried everything to get the Whirlpool Factory to fix it or replace it. So far, I have spent twice the original cost to fix the machine (but to no avail) and now you want me to spend another $500-$600 to try to fix it again? No more!

I bought a Whirlpool Cabrio Top Loader High-Efficiency Machine on March 20, 2013. 14 months later, it failed. When I called customer service I was informed the 1 year warranty had expired (I knew this already) and that all they could offer me was a $319 extended warranty to fix machine and guarantee covered future repairs. Luckily, I had the machine repaired at no cost to me after complaining to the sales people I bought the machine from the year earlier. They contacted their Whirlpool representative who had the repair covered. Now, 3 years and 11 days after purchasing it, it failed again. This time the machine would no longer spin out the water. Whirlpool offered nothing more than to give the website and special code for a discount on a new machine. After some haggling, they agreed to pay for 50% of the parts only, no labor. I argued this machine must be a lemon, as they have told me theyve heard no prior issues with this machine and that it would be reasonable to replace this machine. They refused any further assistance. So I threw this piece of junk away and instead, for $185, bought a simple rebuilt 15 year old Maytag washer with agitator, direct drive. Just a couple of knobs. No computer, fancy bells and whistles. I can say with absolute certainty that I will never purchase a Whirlpool product ever again. I also believe these machines are no longer meant to last like old washers (and dryers) used to.

Purchased Whirlpool Duet wfw9550ww00 in 2012 from PC Rich, who purchased machines in 5/11. Product stopped being made 5 yrs prior. Of course I did not know until my washer went and had service come to my house. He explained prior information, looked at my machine for 2 seconds and said someone put in a heavy load that machine was not able to handle and 2 belts broke and guts of machine are destroyed. Its a $799 fix, not including labor, youre better off buying a new machine. How does he know thats the reason for breaking??? The machine is 2 years old, not a scratch on it!!! Unbelievable!!!! Then states thats $114 for the service call. $114 for 2 seconds!!! Im absolutely furious!!! Whirlpool has a new program (if it helps anyone), if your machine is fairly new they will give you a invoice for 1/2 off a new Whirlpool... Take it from there. There should be a tremendous action lawsuit, look at all these complaints...

WTW6340WW0 - When washing clothes, on the last spin it stops and gives an UL error message. I make sure all the clothes are level and restart at that point but still the UL error message appears and water starts leaking from the underneath of the machine. Weve reset the and unplug the machine but no difference. Please help on what else to do.

The machine works well but it is extremely noisy. Large loads need to be washed twice otherwise they seem to not be washed. This machine washes small loads better. Given an option next time I will buy a front loader.

I purchases a Whirlpool 32 Cubic foot 3 door refrigerator in stainless model WRF992FIFM back on November 29, 2016 from Costco. I noticed that it was not making ice and that the refrigerator was around 50 degrees. This was on October 21, 2017. I called Costco and they contacted Whirlpool who sent out a service person on October 25. I am still without a working refrigerator and it is November 9, 2017 as I am told that a circuit board needs to be located.I have called both Costco and Whirlpool and no one seems to be worried about it. I was told by Whirlpool that if a part is not available by end of day Friday November 10 that I will be considered for a replacement. Considered really? I have never experienced such deplorable customer service on both Costco and Whirlpools part. It appears that this model is a lemon as there are large numbers of complaints on numerous websites. I asked for a refund due to the bad reviews and lack of parts and was denied. I will call on Friday for an update.

Purchased the 2015 Whirlpool Cabrio. Today 5-2018, the panel went completely out. When I called the store (Lowes) they asked if I purchased the warranty. I responded no, she went on to say, “Well since you choose not to purchase the warranty youre stuck”. Even if I paid for the warranty a washer should not break down in less than 3 years. My previous washer lasted 18 years with no problems. We purchased this washer because of the larger load. It was one of the most expensive washers. It’s a piece of junk and the manufacturer will not stand by their horrible product. Please DO NOT buy! I will be filing a formal complaint.

We installed this furnace along with a matching 4ton a/c unit over four years ago. It was installed with a 3 zone computer controlled damper system to separately condition the three floors of our home. This furnace was ideal because it has a dual stage combustion chamber depending on how much demand there is. So besides being 95% efficient, the furnace can run at 70% or 100% heating capacity which saves on utility bills when the whole house doesn't need heat at the same time. It also had a variable speed blower which made start ups and shut downs almost unnoticeable. The blower actually ramps up to speed discreetly and adjusts itself according to the amount of back-pressure it senses. This allows it to respond to varying conditions as each of the 3 thermostats are calling for heating or cooling at different times. And yes here in St. Louis we have had days that require heat on the first floor and a/c on the third floor at the same time. The controller cycles between the two every 15 mintutes. All of these features make it ideal for our 2200sq ft three story brick home(four including the basement where it is installed). This furnace and control system along with new ductwork and dampers were able to replace the two old furnaces and a/c units originally in the home. We haven't had a single problem with it in over four years and would recommend Whirlpool Gold products to anyone I know. If I ever had to do this again in another house I would do exactly the same thing with exactly the same products.

I bought it 3yrs ago, and it give us headache, only two weeks used and it stops working. We call their service center and have them check, findings is the motor not working and have to replace, we are asking them to replace it with new washing machine, but they only replace the motor, what we cannot accept is that they replace it with a surplus motor. Only two weeks used and they replace only surplus parts!!! Damn. What a bad experience... (The motor they put is noisy too)! After a year the spring hinge collapse and have to fix it again. And now my washing machine is like a helicopter when spinning, shaking and moving around our laundry area... I dont want to buy Whirlpool anymore.

It works ok and fits in a tight spot. However, the top shelf will suddenly start to freeze the food and after a day or two it will stop. The fridge makes terrible loud banging noises. Were told it is the coolant but it is extremely annoying. A repairman moved the line closer to a heating and it doesnt bang as much. Because of this, I would not buy a Whirlpool fridge again.