I bought a Whirlpool dishwasher in 2008 from Best Buy and purchased the extended warranty through Best Buy. First of all, my complaint is not with Best Buy (model # DU1145XTPBA). I have had nothing but trouble with the unit not filling with water, being noisy, and other problems. And then, my intelligence is insulted by these independent contractors, who are supposed to be appliance repair specialists. I found that far from the truth in most cases. They have a list of patented things that the consumer is doing wrong: not having a hot water heater next to the unit, using too much detergent, not loading it properly, and on and on. They must think we are idiots. I always would run the water from the sink till it got hot before filling. And I am a miser so I use less detergent than what the manufacturer or the detergent package says. Anyway to make a long tale short, it started leaking last week, so I assumed the door seal or some other such thing. But lo and behold, the door is rotted out at the bottom. The black finish has bubbled up and the metal is actually rotting away. I am from up north and it looks like my old Chevy 2 Nova rotted out. I called Whirlpool and spoke with several people and supposedly someone in management. They were, of course, sympathetic but offered no assistance or explanation. They offered to send a factory authorized repairman to replace the door at more than the cost of a new dishwasher. Are we that stupid? They never offered me a voucher for a discount on a new unit, which I am going to have to buy. I would not have accepted it anyway, as my last few experiences with Whirlpool have been dreadful. I will never buy another Whirlpool anything. The name used to stand for a quality product that you could depend on. But now it is like most things are offered to the consumer in this throw away society. And as long as we keep buying inferior products and only expecting them to last a few years, I am afraid that is what we will continue to get. Be vocal and let them know how you feel, even though they are probably yawning on the other side of the phone. They are without compassion and could not care any less. They are just looking for a paycheck and have probably heard a hundred complaints like mine, so its water off the proverbial ducks back. But when its their own job in jeopardy, perhaps they will start passing on these complaints to someone who will be willing to listen. Its a very bad experience and I will never buy Whirlpool again.

This thing absolutely is total junk. It doesnt clean at all. I have to wash my sons sweaty uniform 3 times because the first two wash didnt clean it. A tub and washboard cleans better than this unit. A 600+ washer should clean the basic stuff. I remove clothes after it was finished and some of the clothes have dry spots where the water couldnt make it to. What kind of washer leaves clothes dry?I wish I came across this site when I was at the store. I did a search and the manufacture website and retail gave it positive reviews. I pretty sure the Whirlpool is paying people to write positive reviews. Technicians have come and gone telling me that there isnt anything wrong with it. That their diagnostic isnt detecting anything. Well when I call them again I will have the tech wait while I wash my sons sweaty uniform and then they can smell it after it goes through the wash. Im going call out a service tech until it works as advertise or they replace it. If I have to call them out once a week. That is what I will do.

Buyers beware! I have had the Cabrio top loader washing machine for less than 18 months and it is already giving me problems. During the wash cycle, it sounds as though the gears are grinding to the point it wakes my family up two floors up! The spin cycle is a joke. The washer sounds as though it is going to spin off into another room! When I called Whirlpool, they told me to shut the circuit breaker. That might reset the computer. No go which I figured as much. I have had washers that lasted 10 plus years with no problems. It is not worth your time or your money. Never again, Whirlpool!

Its big enough, but the ice maker is always messing up, the shelves broke easily, the water takes forever to get cold from the indoor dispenser. The finish, which is called Satina or something like that, dents real easy. It is really a piece of **! When it was new, we had the repair man out 4 times before it was fixed. He even said it was a piece of junk and it should be lemon lawed out. Drawers broke, shelves broke, and parts are really expensive when you break one of the plastic parts.

Within a few months after I purchased my gas hotwater heater, I started having problems with it not wanting to stay lit. It was purchased in 2004. I see that this is an ongoing thing with Whirlpool. Every time I would call them, they would give me stupid answers on what it could be. One lady got hateful with me. I have replaced every part several times and Im having problems. About every two to three months, Im replacing thermal couple. As of right now, Ive been without hot water for eight days. I called and he told me about a trip button that is in the little white thing that has wires going to the thermal couple. I push in on it and then tried to start my heater and it worked. They have never offered to replace it or even give me a discount on a new one. No one should be having so much trouble out of your hotwater tank. This is not normal. These are defective and should be recalled. This company is ripping the consumers off and we need to stick together on this and do something about it. Im afraid to buy another heater because I can see that the new ones are still junk. What do you do?

Back in the day GE appliances were made to last and last - the only one I have found close is Whirlpool. They have style, dependability and long lasting products. My washer machine has a ton of features and I didnt pay more for any of them.

Oct 14th I walked down to our basement to find it flooded. Turns out the leak came from the solenoid that controls the water feed to our Whirlpool Gold Series refrigerator. Now, some $28,000 in damages later - floors/cabinets/walls/electronics - you name it. The repair company said that they replace these units a lot as it is simply a faulty design and Whirlpool knows this as this part is very difficult to obtain - too much demand. Well aside from the cost, the inconvenience, and the rise in our insurance rates the repair person said there was a good chance of the new part failing as well - it just cant take the water pressure as it is just cheap plastic. My advice - stay away from Whirlpool!

I purchased a Cabrio washing machine and discovered multiple repair issues over the last few months. I have had to replace a pump for $85 and now the machine will not complete a cycle. I found out the the whole thing is rusted above the barrel which is causing a leak in the back and leaving our floors covered in rust shavings. From my research and reading others reviews and issues, they pay for a serviceman to come out and still it does not solve the problem. My husband is a student in college and we are living off student loans. We bought this machine because we trusted that a Whirlpool would last and be a good investment. I am very displeased on this machine and doubt I will ever put my trust in Whirlpool again. I called to complain and got the typical response I have read others got. I am not paying for a service call when it will not fix the washer in the end. I plan to file complaint after complaint and encourage any class action suit against Whirlpool for producing a poor washing machine and misadvertisement on this machine. I will move forward in this. I feel that as consumers we have a right and should have a sense of ease when you spend $900 on a product that it should work and not give out as it has so quickly. If there has been multiple people with common complaints, then there should be a recall on this washing machine.

We bought our Whirlpool Cabrio Platinum top-loading high efficiency machine Model #WTW8000BWG in Feb. 2015. It cleans well, and is easy to select water temp, spin speed, etc. It's simple to load, but because I am short, I have difficulty reaching stuff at the bottom of the tub. A stool is needed. LOL. In the 5 years that I have owned it, I have not needed any kind of service to be done on it. Very reliable. I have had Whirlpool washers and dryers before and my success with them is why I purchased the set I have now. And so far, so good. Highly recommend.

Purchased Whirlpool Duet wfw9550ww00 in 2012 from PC Rich, who purchased machines in 5/11. Product stopped being made 5 yrs prior. Of course I did not know until my washer went and had service come to my house. He explained prior information, looked at my machine for 2 seconds and said someone put in a heavy load that machine was not able to handle and 2 belts broke and guts of machine are destroyed. Its a $799 fix, not including labor, youre better off buying a new machine. How does he know thats the reason for breaking??? The machine is 2 years old, not a scratch on it!!! Unbelievable!!!! Then states thats $114 for the service call. $114 for 2 seconds!!! Im absolutely furious!!! Whirlpool has a new program (if it helps anyone), if your machine is fairly new they will give you a invoice for 1/2 off a new Whirlpool... Take it from there. There should be a tremendous action lawsuit, look at all these complaints...

Whirlpool has been a well known brand for many years producing well made appliances. With strong customer support and appreciation. I myself have owned many appliances made by Whirlpool from Fridges to Washers and Dryers with no problems.

The wife and I are retired and when it came time to purchase a new washer, we thought we would spend the money and buy top of the line so it would possibly outlast us. So we went to Lowes and spent $1000.00 plus on a Cabrio. Within the first year, the control board went bad, replaced under warranty, now no matter how little or much of a load the wife puts in this piece of crap, it goes off balance!!!Of course as previously stated, customer service doesnt give a crap because we also saw no need for an extended warranty having made such a large investment in a washing machine that we thought was built with a high standard of quality, SHAME ON US, SHAME ON YOU, WHIRLPOOL!!! You have lost a customer who has been buying your products for a long time but will never buy another and will be warning everyone we can to do the same.

Light bulb went out in the freezer. Come to find it is a led cluster with a circuit board only cost $30 to $100. Engineer should be fired. What is the reason to take simple bulb and custom bastardize into an expensive hybrid. Greed.

I bought this Whirlpool Cabrio Washer 3 years ago. Yesterday will be my last repair. I installed a new tub (bearing failed have to buy a full tub to replace), new suspension rods and a new stator and rotor (cracked). Last year I replaced a drain pump twice, and a computer board. All of these repairs since I purchased this washer have cost me well over $900 for a $1400 machine. I dont mind replacing a pump every few years but these larger failures are unacceptable. We have moved back to Kenmore on some new appliances we purchased this year as result of trouble with Whirlpool. Whirlpool should send out a recall on the suspension rods; the existing ones seize at the top and stop functioning causing the tub to shake excessively. This led to the cracked motor (rotor cracked).

I bought a Whirlpool refrigerator almost 10 days ago. They delivered a broken refrigerator and then the technician raised a replacement request. And then started the game of ignorance. Since 10 days I am calling hundreds of Whirlpool persons including Area manager, ware house, customer service, nobody is giving any date when I will be getting it. Moreover, they have stopped taking my call recently. Right now, I am at a loss how can I get a refrigerator or my money back... Last option is consumer forum. I really request you to never buy a Whirlpool refrigerator.

I purchased a Whirlpool front loading washer from PC Richards in January of 2010. The warranty was only for one year (the washer was new, not used). The model # is WFW9050XW. Anyway, the washer had to be repaired by PC Richards twice in the first year I had it. Once because the belt that makes the washer spin broke, then because the pump got clogged. Unfortunately, when you wash your clothes, your socks and underwear can get sucked into the pump. After that warranty expired, I purchased a warranty from my utilities company (PSE&G). I have had to contact them four times for repairs to this machine. The most recent problem is my clothes are still wet after the washer stops. I actually have to wring them out by hand to get the excess water out. When I contacted my utilities company about servicing the washer, I was informed that if the repair is more than the washer is worth they dont have to fix it. I canceled the repair and now got to the laundrymat. I figured if I wait until the end of the year, maybe the repairs wont seem excessive. I contacted Whirlpool about the problems and was informed that I should have been using a garment bag to wash my socks and underwear in. More or less the person I spoke with made it seem as though it was my fault the machine sucked up my underwear and socks. I, on the other hand, disagreed with her. I told her the washer should have been build so that it would not suck up these items. I was so totally pissed off I ended the conversation. I also informed her that I would not be purchasing any other appliances manufactured by Whirlpool or Maytag as they are affiliated. They obviously have no integrity when it comes to their product. However, I am totally baffled. Why do the Maytag machines work better and last longer than the Whirlpool machines? The washer I replaced was a Maytag. I had that machine for 17 years!!!!

I just bought my stove four years ago. Every time I want to bake something, I have to run a fan on my stove because it overheats and shows an F2 error message. I then have to unplug it, leave it unplugged for 20 or so minutes. Once it cools down, I can plug it back in and use it. I have to go through this every time I use the oven. Its annoying and I lose a lot of food because sometimes, it just wont work. Idk what to do!

I have had my washer & dryer about 12 yrs. It has given me great service; however the spin mechanism on the washer stopped one month ago. It was replaced thru my home appliance warranty. I need the front loader style because Im disabled now, and cant take clothes out of washer. My previous set was Kenmore & it lasted 20 years. Looking to purchase in 2 months.

Purchased new from Best Buy for over $1000. One or two months after the warranty expired the ice through the door malfunctioned, would only spit out crushed all over the floor then clog up. Didnt bother to repair it, just open the freezer. Next, the door would not seal right and frost builds up in my frost free. Also, the ice delivery wont close tight. Now the unit is about 3 years old and I just finished paying it off and all the door shelves are cracking. Contacted Whirlpool and was told by email politely, Too bad. You are out of warranty, but please buy parts from us and say nice things about Whirlpool because we so value our customers. Never will buy Whirlpool again and recommend you DONT.

My experiences using Whirpool ranges and ovens have been very positive. As a matter of fact, that is the brand preferred by my family through several generations. Durability, reliability and warranties have been the main features we have found useful. Most of the ranges and ovens have been replaced at home, always with Whirlpool brand, but with added improvements that manufacturer come up with, in order to integrate our devices to the latest technologies. I would recommend this brand to the readers, friends and neighbors.

Whirlpool Cabrio Platinum top loader 2014 model - This washer is an over engineered piece of junk. It takes forever to wash anything and it never gets anything clean. I wish I would of just bought the repair parts for my old machine which I had for twenty-three years.

Whirlpool Cabrio WTW8500DC0 - 2 months out of warranty, 14 months old. Motherboard fried. $300 if I do it myself. $550 to have it done. The unit was $780 on sale. Brand new piece of junk. Zero stars but thats not an option. Quite honestly, it doesnt clean very well and it doesnt rinse very well so we have to rinse twice to get the smell out if we use bleach. So whats the sense in buying a high efficiency washer? I work outdoors and weve had cheap washers in the past that clean much better and lasted many years.

In the first year of my Whirlpool Washing Machine, the motor quit working entirely. Fortunately, the machine was under a 1-year warranty and the motor was replaced by a Whirlpool service technician. My big complaint with this washing machine is this: Even though you select hot water for the wash cycle, the machine has sensors in it that only allow the water to get lukewarm. If it senses the water getting too hot, it adds cold water to bring the wash temperature back down to 78 degrees F. Next time I will do my research and buy a machine that actually allows one to use hot water.

I purchased my Whirlpool refrigerator last Summer and so far I’ve had no issues, no probs! I love the energy efficient refrigerator along with its easy settings and options to use a ice maker. Wouldn’t trade my Whirlpool for any other brand!

I bought a new Whirlpool electric range in the spring of 2008 and purchased the extended warranty from Leons. The oven worked fine for the first three & 1/2 years, but then the bottom element in the oven seemed to have stopped working. The top element would still come on, in an effort to keep the oven at temperature, but was not effective.I called in a repair. The technician showed up, turned the oven on, noted that the bottom element did not come on properly & replaced the motherboard in the control panel with no further diagnosis. The oven worked for approximately 9 months and then the problem recurred. I called in another warranty repair. This time when the technician showed up, he turned the oven on & told me he was going to order a new bottom element, which he installed about a week later, again, with no further diagnosis.Now, here we are again, one month off warranty and 6 mos since the last repair, and again, the bottom element in the oven is not working correctly. I reported the issue & my dissatisfaction to Whirlpool and was basically told, How sad, too bad - hardware components fail and theres nothing we are going to do about it. Seriously? This range is just barely 5 years old and has a history of repeated problems with the bake function - obviously, something is defective in this product.I can see it, if I had not had any problems until this point, but when the same issue keeps coming up & obviously has not been correctly diagnosed and repaired, I would think they would have enough integrity to offer some kind of help or solution. Given the history here, its highly unlikely that Im going to be willing to spend big bucks on another attempted repair that, in all likelihood, will be merely a short term band-aid, so Ill probably have to buy another new range - which I cant really afford right now. Trust me, it will not be a Whirlpool & it will not be from Leons.

There seemed to be an issue with the Whirlpool Cabrio Washer Pump. If a button comes off from your clothing or snap, etc., it gets trapped in the washer pump, causing it to crack and leak. Whirlpool on warranty only allows for one free change and anything after that costs $300.00. This is going to be the third time we are having problems with this and it is becoming, economically, a struggle for us. We have checked every button and snap to make sure they are fastened tightly, as well as any other type of items that may fall off in the wash and become trapped in the pump causing it to crack and leak. These pumps were poorly made and Whirlpool needs to be more aware of this problem rather than telling the customer that they are not aware of the situation.

Whirlpool Gold with bottom freezer, had it for about eight years and no problems. Great seal and great storage space. Also plenty of space in the freezer. We are a family of four. It is extremely quiet. There is flexibility as to how to mount the shelves and they are easy to clean. I have never had any spoilage.

We purchased our Whirlpool range a few months ago. We have the 6.1 cubic oven which is large inside with 5th element on top for keeping things warm which is a nice feature. The oven wipes easily if any spills occur. The only issue I have had is the top scratches easily. I used Creams Brute to clean the top which does well.

I exchanged my fancy front loader Cabrio washing machine for a top loader after having numerous issues: clothes werent getting clean, extended water cycle, and a leak. The original purchase was made at Lowes, where I elected to invest in the 3 yr extended warranty plan. After several visits from their sub-contractor, they allowed me to exchange the washer for a top loader Whirlpool Cabrio. At first the washer seemed to work, but after about 8 months I started having problems. The bearings went out and when the service company replaced it they forgot to screw top of the machine together. During my first load, I heard this terrible noise and discovered that the entire top of the machine had separated from the bottom by 2 inches. I frantically rushed to turn the washer off before my laundry room flooded. So, they were out again and screwed the machine back together but failed to retrieve the original screw that they removed from the washer during the first round. Well, the screw got lodged in-between the drum and interior, causing it to completely break the machine. Lowes agreed to exchange the washer for another top loader Cabrio, but my 3 year service contract would not cover the new washer. Not to my surprise, I immediately had issues with it and had to hire a repairman to assess the problem, who concluded that it was the bearings. He informed me that it would be about $700 to replace the bearings and cheaper to just buy a new machine. I called Whirlpool and explained to them about all my issues, now becoming almost comical. They arranged for an outside contractor to assess it. After confirming that the bearing were bad they replaced them. Another few months go by before problems occur, this time the washing machine stopped draining water and spinning. The service company was out another 4 times. They replaced things like the mother board and control panel. My last appointment was today, where the service guy said, There is only one error code. It is a stuck button. I said, Will you at least witness a full cycle so I can show you all my problems: clothes still dirty and stinky, items still wet after spin cycle, cycle taking 2 to 3 hours to run, horrible noises, and timer adding minutes to original cycle. He called Whirlpool because he genuinely felt sorry for my situation. They were of no help. He didnt stay to witness a cycle. Moral of story: if the error code doesnt detect a problem, the consumer will not be helped (this is something that consumers do not have access to). They will happily call a technician out to put a bandaid on an issue until your warranty runs out. I have had between 7 to 10 service calls out to my house, requiring me to take either an entire or 1/2 day off of work each time. If I added up all time lost at work, I could have easily purchased a top-of-the-line washer/dryer duo and been done with all this Whirlpool foolishness. Do yourself a favor, stay away from this product.

I am a retiree after 35 years and 5 months, the last 20 plus years on salary. I purchased a new Whirlpool washer on April 18, 2012 at Lowes in Tiffin, Ohio. The clerk said to take the receipt to Clyde to apply for my rebate. I was informed by a receptionist that we only get a rebate if our purchase is from Sears. I only went to Lowes because of the urgency and was not aware of this change in your policy. I consider this a real slap in the face after all the years of what I consider excellent service to Whirlpool Corporation.

Aqualift is a Joke. We recently remodeled our kitchen and purchased a new Whirlpool range model #WFE710HOAE. It came with a feature called Aqualift Technology to clean the oven. The button you push to start it says Aqualift Self-Cleaning. I followed the simple directions and when it was finished I was surprised to find that nothing was clean. I tried it again with the same results. I had to then clean some of it with the enclosed scrubbing pad. You cannot use any cleaners except one that they also send a small sample of. In short, it was like the old days cleaning my mothers oven with a scrub pad and a lot of elbow grease. I spent 30 minutes getting it somewhat clean. I am so disappointed and mad that Whirlpool can just blatantly mislead consumers this way. No one wants to buy an expensive product such as this and have to clean it by hand. You get as good a result if you do not even use Aqualift. My last range lasted 20 years and all you had to do was take a wet cloth and wipe out the residue. Whirlpool is at best incompetent and at worse criminal and purposely misleading with this and other similar models and should recall or be forced to recall and replace these with a working technology. I am surprised that the Federal Government has not stepped in. I would be very supportive and would participate in a class action lawsuit on this matter. As I stated in the beginning, this product is a joke.

We purchased a new home April 2013. All our appliances were new Whirlpool stainless. Looked nice. After almost a year our microwave started acting improperly. Beeping, changing screens, not working when buttons pushed. Then the micro wave had a melt down and caused the glass try to break, parts to melt and caught fire internally melting plastic. Notified Whirlpool and they sent out individuals to repair. After several weeks the repair was completed and we were advised that they did not understand why this would or could happen. We should be fine now. Well we are now again having this unit beeping, changing screens, not working when tried, and when entering numbers, number and time are not what was trying to be entered. This unit my wife says is possessed and she wont use it. She fears it will burn the house down. It is Velos model TR 2 24 11000 serial number. It now beeps and changes with door open as I read the serial number.

Bought it less than 2 months ago. It doesnt wash. It doesnt spend. It works every 2-3 hours if Im lucky. Its the worst product ever. Its not like it was refurbished. It was brand new. Smh. I thought it would save me money by buying a washer. Off to the laundromat I go. I do not recommend this product especially to someone who has a family and on a budget.

On March 3, I purchased a dishwasher (Model: KUDE70FXSS1 Serial No.: F10202361) on Whirlpools VIP link, which will more likely be my last Whirlpool purchase based on the slightly damaged product and incredibly poor customer service Ive received. Upon delivery of the dishwasher on March 9, I noticed that the left rear wheel was damaged and slightly bent. I also noticed that the unit was a little off balance. But the delivery person explained to me that everything was okay and that the front legs just needed to be adjusted. I believed him and signed the delivery receipts with the additional note about the left rear wheel being damaged. At the time of delivery, the driver also happened to mention that J.B. Hunt did offer installation services for dishwashers. I then called Whirlpool customer service, which pretty much gave me the cold shoulder, and said that it wasnt in their policy. I had to request the installation service at the time of purchase and Whirlpool would not send someone back out. This made me upset because I initially wanted to have the dishwasher installed but your VIP link didnt show an option for installation. Im not sure how Im supposed to request the installation services when theyre not being offered. But the genius customer service representative thought that I should intuitively call Whirlpool when the link isnt on the website. This is the first demonstration of Whirlpools poor customer service, in my opinion. After a couple of days of driving around to get a hose and a cord to perform the installation, I finally installed the dishwasher on March 12. Once installed, I noticed that the hinge on the left side was rubbing against the tub of the dishwasher. The door hinge was bent and the main tub was slightly damaged. Again, I contacted Whirlpools customer service department who sent out a repairman who confirmed that the dishwasher needed new tub and hinges which were covered under warranty. Unfortunately, he told me that I would not receive a new dishwasher since I installed it myself. He would order a new tub and hinges and transfer all the equipment and wiring from my original dishwasher to the new tub. Essentially, I would have a refurbished dishwasher at a new price, which I do not want.I initially wanted to have the dishwasher installed but your VIP link didnt show an option for installation. If Whirlpools website worked the way it should have and offered an installation service, I wouldnt be in this situation. I would have paid for the installation and the people installing the new dishwasher would have realized that it was damaged prior to them leaving and ordering a new dishwasher. I am a customer and not a dishwasher repairman. No normal person would have been able to catch the damage that is on my machine. Second, I find it hard to believe that Whirlpools policy states to have all the equipment from my original dishwasher installed on a new tub. So, I paid $989 for a new dishwasher thats really a refurbished dishwasher because of the damage. I wish I would have visited this site prior to purchasing. I will never deal with Whirlpool again.

I bought a Whirlpool 3.4 Cu Ft. Top Load Washer, Model: WTW4800XQ on Sunday. Today is Tuesday morning, but the machine broke last night. It lasted for about 5 loads and they were not big loads, unbalanced, and yes I had the right amount of soap. Whirlpool is saying that I washed something that was not machine washable. However, that is simply not true. I washed the bathroom rugs (which have been washed many times before) and they are saying the pump is clogged. If I had a washing machine 48 hours ago, do I really have to pay a service repairman to fix it? I will never buy any Whirlpool product again.

I purchased a Whirlpool WFW9050XW washer in Aug 2011. I have had nothing but problems. Sears sent repair tech 2x; it would work for a couple months and stop. Whirlpool has sent new motor, tub, switches, etc. I feel I bought a lemon and I want Whirlpool to replace the machine.

I had a full set of kitchen appliances delivered to me on December 11. The delivery crew installed everything but the microwave because we needed to have wiring done. Three days later an electrician came and upon opening the microwave box it was severely damaged. Whirlpool won’t replace it because I called one day outside their 48 hour window. They delivered me a damaged product – period. It should be replaced without question. Instead they want to send a “cosmetic tech” out to see if it can be fixed. I can’t imagine that’s a more cost-effective method for them. Completely unacceptable. I will never buy Whirlpool again based on their lack of customer service and common sense.

I just replaced our Whirlpool Accubake Double Wall oven, model RBD305PDS14, because it fried the control panel after being put on self clean. This was the second time this has happened and I have probably only used the self clean feature three times since we purchased the oven. Im not a specialist in defective product design, but having a control panel burn up two out of three times when the self clean is used suggests a significant problem. I refused to pay to have it replaced again and obviously did not replace it with another Whirlpool product or any other brand associated with the company. I see that this problem has a long history dating back quite a few years with Whirlpool doing little or nothing to resolve the issue. (They just deny any knowledge about any defect in the design.) Fool me once, shame on you! Fool me twice shame on me!

Had a Kenmore - I was told it was made by Whirlpool. It did a much better job of preventing wrinkles on no-iron clothing. Also, I liked the dryer shelf for drying pillows, tennis shoes etc. I have been told there is a shelf for mine but has been backordered for months.

I hope this review makes it to the president of Whirlpool! My husband and I built our first home and finally moved into it on April 22, 2017. We saved everywhere we could and I did my best to research my appliances. I was so excited to buy a BIG refrigerator for our family of five, (3 are hungry teenagers!) after years of using a smaller side-by-side. We went with the 31.5-cu ft French door/drawer with dual icemakers, model #WRF993FIFM. The original price was $3,599 but we got it on sale for $2,298 at Home Depot. After only 5 months it stopped cooling! I woke up one morning to find a fridge full of spoiled food!! After waiting 3 weeks I had 2 different repairmen come out and have been told that it is un-repairable due to two parts that are needed, one of which is on back order indefinitely. Ive called Whirlpool numerous times and only get the run around and Im sorry mam we cant do anything else. So Im just supposed to be without my refrigerator until who knows when?! The first 2 weeks of this crap we had to live out of Igloo coolers on our back porch. That meant no buying real groceries, only milk and juice and drinks. Thankfully the awesome people at Home Depot brought us a loaner, which is an apartment size fridge, to use while we wait. So now I just have to walk across the house to my garage every time I need something, and I cant buy much food because it wont fit!! Im so disgusted with how Whirlpool is handling this!!! Not only did we buy our fridge but we also went with Whirlpool for our stove, dishwasher and microwave, and we already owned a newer Whirlpool washer and dryer set. We spent thousands of dollars and cant even get them to exchange this piece of junk! Come on Whirlpool, surely you dont treat all your customers this way!? Do the right thing and let us have a replacement!!!

First three months, the main water gasket broke. Thank you for lots of water all over the kitchen. I pulled the washer out to inspect the cause, wanted to see if it was house plumbing or dishwasher. The hose was hanging off the bottom of the machine. During the 45-minute call, I got in my car and drove to plumbing supply and applied a new hose clamp. The next day, a free service call, the repairman said it was the second one this week, Thats just what I would have done, but would not put the machine back. (void the warranty, finish work, etc...not sure how he would have serviced the machine if I did not pull it out for him). A few months later the wheels on the top shelves give way/fall off the rack, so we have those replaced. As soon as one is replaced, the other side falls off... Now, approximately 14 months into installation, the dishwasher does not work. The control panel is flashing and will not start. What a runaround with KitchenAid. We were told there was a recall on the hose clamp (we never got one). We cannot have the control panel worked on until the hose clamp is certified... That will take a week. Then we can call back... What a hassle. We bought this expensive product on good reviews. We are most disappointed. There is very little concern for making the product good. Its incredible that so much can go wrong in such a short time of limited use. Once/day... The hose clamp is just poor engineering. The rest is terrible quality and support

I just bought a new dishwasher because my 5-year-old one went out, model number DU1145XTPBA. After pulling the old one out, I took the motor out and lo and behold, what did I find but bad bearings. The motor was fine, just the bearings were rusted out and were jamming the motor so that it wouldnt move. The price of a new motor, $149.00. Well thats a bit much for something that only lasts 5 years. I went on eBay and found them for $70 to $170.00. So if you have a problem where your dish wont wash at all but fills up with water, it may be nothing more than cheap bearings in the motor. If I, myself, were this companys CEO i would really consider changing companies that they have making these motors or at least the bearings. Just wanted you to know that this is the only problem I have had with this one and Im going to replace the motor now that I know what it is. Thank you Whirlpool for a day spending repairing and replacing one of your dishwashers. I learned a lot.

Cabrio Top Load Washer model WTW6800WW1 - Although we were very happy with the vendor where this was purchased and happy with the majority of the washer function; there is a problem with the cabinet & lid connectors rusting. Specifically, the lid connector on the left side totally rusted out, and also around the bleach cup, rust. There are also rust spots where the seam of the top section of the washer meets the bottom part. The washer was purchased in 2009. We have had it serviced in the past, prob 5 years ago, it needed a new motor and the rust was beginning to show then, while under warranty. I recently called Whirlpool and the associate told me that she had never received a call with regard to this type of problem. She did give me names and phone numbers of appliance repair in my area. I find it odd that Whirlpool would not make their associates aware of issues like this. I searched online and saw more than a few complaints about rust. So on it goes, no recourse, and as I read about the problem from others reporting this; it was mentioned that the vapors from the bleach cup etc, contribute to the rust. Additionally, even if it was under warranty, I was told that this is considered cosmetic and it would not be covered. Until... and I can only suppose, that until the lid possibly falls off while lifting, the cosmetic ruling may then turn into a function problem. Now there is also a squeaking sound, so off to call the appliance repair, check the cost and next time... buyer beware. I guess a lesson in science as well, hopefully this design flaw will be corrected for the next models in process.

This Whirlpool refrigerator is only 1 year and 3 months old (just out of manufacturers warranty). I am very happy that I bought the extended warranty. I have had to have 2 service calls in the past month. On the second one I was told the compressor needed to be replaced. I have had refrigerators that were 25 years old and never needed service and are still working. I have seen many of the same problems being reported on Whirlpool Refrigerators of this type. I recommend you steer clear of them. Also KitchenAid and Maytag because Whirlpool makes their refrigerators too.

DO NOT BUY THIS DISHWASHER (Whirlpool Gold Series dishwasher)!!! We bought a camp with this dishwasher in it brand new. It has been serviced three times in the past year because the dishes (especially utensils) do not dry. The service company first said it was because I needed to use jet dry. What a joke! I told them I was using jet dry so they sent a service man out. He had to read a manual in order to try and figure out what was wrong with it. He then decided the entire motherboard needed replacing and he would order the part. He came back, replaced the part and it still did not fix the problem.I called again to complain so they sent another service man out and he said the drying air vent may not be working. They came back out to replace it weeks later because the part was on back order. Wonder Why??? I still have to dry the utensils every time I run the dishwasher. The interior walls of the dishwasher are wet even after running through the drying cycle. Either this dishwasher is a lemon or Whirlpool is selling a dishwasher that does not dry to the consumers!!! So BEWARE!!!

Long story short is that my dishwasher was 7 months old and two parts went out on it. 4 months (and almost 3 hours total on the phone) later it still does not work. Whirlpool only has one repair person in our area and that person is a small business owner who works alone and is now in his 2nd week of vacation leaving no one else in his shop to do repair while he is out. I do not know if my part is ordered nor do I have a repair date! Never will I ever again purchase a $900.00 dishwasher or any appliance from Whirlpool!

Purchased a Whirlpool french door refrigerator at Lowes less than two years ago. Last week the freezer compartment failed, out of the one-year warranty of course. The independent tech who came to service the machine told me of all the refrigerators he services Whirlpools are the closest to total junk and he would never recommend them. Wish I knew him before I bought this soon to be piece of trash. The CEO of Whirlpool, Jeff Fettig, received total compensation valued at $14.4 million in 2010, up about 15% from a year earlier, the appliance maker reported in a securities filing recently. Appears to me that Mr. Fettig is ripping off customers for his own gain, with his boards approval. Shame on all of them -- another example corporate rip offs that are plaguing our nation.

Whirlpool contacted me today about a review I posted on their website about the washing machine I purchased from one of their distributors. It was not to say they were sorry for the washing machine ruining our floor or our clothing. It was to say that they will not post my review because the model number is not the same as the one I purchased. Unfortunately for me my model was manufacture discontinued and although they look alike this new model is significantly different than the previous model it replaced (I will believe that when I see it). So they obviously knew there were problems with the earlier machine. I am outraged that whirlpool would stoop to such low business tactics to sell their garbage to people and then treat them like dirt.

We purchased the Top Loader Cabrio in 2006 for $1100. About 1 yr. later it just stopped, but was covered under a recall. A year later it stopped working again and cost $400 plus we bought a 3 yr. service contract for $350. A few months after the service contract ended, the spin cycle got very loud and it started leaking grease and water. It now need a ball bearing and $600 of work. So now we spent almost $2000 for this washer in 8 yrs. Our Maytag was $400 and lasted 15 yrs and we gave it to someone else who is still using it and we never had it repaired. It sounds like Cabrio customers have been complaining about the same issues for several years but they keep recurring and Whirlpool is doing nothing to correct them. We are not putting more money into it after reading all the complaints. We are buying another washer and another reliable brand. I would have been a customer for life because I did like the way it worked and cleaned, although I hear so many people had problems with that so I am not waiting for that to fail too. And I recommended the Cabrio to several people who bought them and now I hear they are starting to have problems. You should stand behind your product and correct these problems and recall or fix them at a reasonable cost.

I have been a dedicated Whirlpool customer for 50 years. I purchased my new, Cabrio washer and dryer in 2011. The dryer works fine. The washer does not. It ties everything in knots. Most everything comes out in one large, wrinkled lump. When washing sheets, it wraps the whole load in a soaking wet, fitted sheet bubble. You cannot wash one item by itself, because it will become unbalanced and shutdown. I will say that I havent had any repairs yet, but I have a feeling, its only a matter of time. I have decided to buy a new washer, but it will not be a Whirlpool.

I bought a Whirlpool washer in Aug. 2015. At the end of September I had to call and get a repair man to come out twice because my clothes got stuck way down under the agitator. Not only that, but it does not clean my clothes well at all. I am really dissatisfied with this washer!!

I absolutely hate my Whirlpool refrigerator! The first day I had it, the cover to the deli drawer fell off and cracked because it wouldnt stay on. I called the company and they sent me a new one but it immediately fell off and broke also. It is just a terrible design. The plastic slots dont fit correctly and it just doesnt stay on.Then, a few months after owning the fridge, I notice rust spots on the bottom drawer. I called the company and a rep told me to buy dishwasher cleaner and a magic eraser and use that to scrub the rust off. She insisted that it must be near humidity. I explained that my GE stove and dishwasher, along with other stainless steel in my kitchen have never rusted. The Whirlpool company provided no help whatsoever and does not back up their warranty. I would never purchase another Whirlpool appliance after this experience. Now I am stuck with a fridge that has rust stains and a broken door.

Two years ago, I bought your new stove. It was under warranty. The computer is messed up. They came and they did not fix it. Warranty is off. It hasnt worked right since I got this stove. Who is going to make it right? Its only two years old. Fr2 v comes on when turn on. Oven have to turn power off to get it to work. This stove sucks.

We bought this Whirlpool washer dryer set last year and extended warranty. 7 weeks ago the washer stopped working. I have spent around 60 hours so far trying to get the washer fixed. Have talked to the repair shop as well customer care up and down the chain. 5 visits so far by technicians and still not fixed. Customer care people promise to call back w/update but never do. We were going to buy LG but bought this to give business to an American company. Now our patriotism is bearing fruit. Customer care blames AIG (service contractor) and Whirlpool say that they can’t manage AIG. At the end of our rope with constant trips to laundromats. Have no idea if it will ever be fixed. So frustrating to see the name of Whirlpool tarnished to this extent. Nobody seems to be in charge and everybody passes the buck. Whirlpool is a shameful example of a company that deserves to go out of business.

My Whirlpool microwave fits nicely over the stove/oven. It is easy to clean and comes with a glass turning table. It also comes with a wire rack if you choose to use it or it is easy to remove. I have had this microwave for 12 years and never had a problem. Love the presets on it for example ‘“popcorn.”

I purchased this machine about a year ago and it is the biggest piece of garbage on the planet. The biggest problem is that it will not spin if the load is even slightly unbalanced. It does not clean the clothes. If you try to rebalance and spin the load, it adds more water and then gets stuck in a cycle where it drains and adds water forever. Do not buy one of these. I am finally surrendering and buying a different machine. A total waste of money.

Before a year was up after purchasing 4 Whirlpool appliances for our kitchen, our refrigerator needed a new compressor. Of course, they covered the cost because it wasnt a year old yet. After much complaining, they gave me a whopping extra 3 months coverage, until Jan. 2014. Now we have water leaking on the floor and ice collecting on the bottom of the freezer drawer. What a piece of junk! I had sent an e-mail to Whirlpool after the compressor situation telling them that I would never buy from them again and would have nothing good to say about them. No one responded. Goes to show that Whirlpool could care less about their customers satisfaction. Never again will I buy anything Whirlpool makes. By the way, our old frig is in our mud room working absolutely fine.

Whirlpool Cabria Washing Machine hold down switched failed in just 18 months of use. It took the Technician 5 days to serviced and repair our Whirlpool top loading washing machine. The washer is till acting up and stop working unless you put a weight on the top loader cover.

Our Cabrio washer often ties clothes into (unwashed/still dirty) knots. They are so bad that it takes several minutes to untangle and then the load has to be rewashed. It also has to be set for hot water when you want cold, and vice-versa. I am unable to do that for the rinse cycle, so all our clothes are rinsed in hot water. It doesnt even get the clothes clean, when it doesnt tie them up. Ive gotten used to it sounding like the space shuttle taking off and managed to shut off most of the annoying beeps. The dryer is almost as bad, it seems to take a long time to dry clothes, and they come out very wrinkled, even on the wrinkle guard. The finish isnt even good on either one. It scratches very easily, and scratches start to rust almost immediately. This is quite possibly the worst piece of junk my family has ever owned, except maybe for an unfortunate experience with a 77 Dodge Aspen. We bought this set thinking we were paying enough that we were getting the best. Never again!

For the last month, in order to wash dishes, we have to start the dishwasher normally. The water will begin to fill the tub and then stop and all the display lights go out. We push the cancel/drain button and the dishwasher empties the water in the tub. We again, push the desired wash cycle button just like the first time and the dishes wash normally. We have purchased at least two of this same type dishwasher with the utensil holder in the door from Whirlpool in the past, with great satisfaction.

We were a Whirlpool family, and have been using a Whirlpool front loader – Duet Steam Model # WFW9500TW - for the past nine years without any issues until recently when it started to vibrate. Technician sent by Whirlpool blamed it on failing bearing and that it was cheaper to replace than to repair (In hindsight, I wish we had tried repairing). Naturally, we decided to replace with a new front loader from Whirlpool - Model # WFW6620HW. Our previous version had a max spin speed of 1000 RPM and a capacity of 3.5 cu. ft. This new one has a top spin speed of 1160 RPM and a capacity of 4.5 cu. ft. The main problem with our old one was vibration, and this was being caused by the washer going into high spin while the clothes were not evenly distributed throughout the drum. In one spin, the clothes would spin perfectly without any vibration, but in another spin of the same cycle, the washer would not allocate that same clothes properly throughout the drum, which leads the drum to cause vibration from unbalanced high spin. Vibration is a problem, because like most Americans, we live in a wood frame house, and have a basement underneath with the washer located on the main floor. Vibration from unbalanced high RPM spin gets sent down to other areas of the house, causing damage, drywall cracks, separation in trims, etc. And these are all only the damages one can see with their eyes.One point about vibration and some myth busting. Provided that all your washer legs are meeting the floor and not on a saggy floor, your washer should not vibrate more than it does during an empty spin. If it does, then it is due to faulty, poor design/engineering. What happens is when the steel drum becomes unbalanced with laundry in high spin, it starts to shake as more of the weight is on one side, which one can notice looking inside the washer window. There are concrete weights fastened to the top and bottom of drum to keep the drum in place and to reduce its shaking tendencies. However, this weight also causes the washer cabinet to wobble if the drum itself is shaking. This wobble in turn causes the washer legs, which may be firmly grasping the floor, to very slightly come off the floor, which one can feel if touching both the washer feet and floor with their finger at the high spin of an unbalanced spin. And that motion of legs coming off the floor and hitting back at high RPM is what causes vibration to be felt on the floor and to be seen on the cabinet. Of course, this effect is amplified with washers that decide to go into an unbalanced spin with an even higher max spin. When our old washer perfectly balanced the clothes, it behaved like it was running high spin while the drum was empty. This is how all washers should behave, especially in America where the vast majority of homes are wood frame based. However, that was not what we experienced with this new Whirlpool. If a washer is not capable of balancing out the clothes, extra function or feature should be deployed in containing the drum shake to within the drum, and not allow it to escape.First, our old front load Duet Steam Whirlpool was Made in Germany. This new one is ‘assembled’ in America. The door window of the new one is plastic and feels cheap and flimsy, but I expect all the darker color door windows of newer front loaders to be plastic. Consider it cost cutting. We did not look for additional anti-vibration technology because our old Duet didn’t have anti-vibration features aside from its two springs and four suspensions. We decided not to use Load & Go because I have personally seen liquid HE detergents gum up over time, so I didn’t want to risk it gumming up inside the washer.After the installers left, I spend an hour cleaning the outside of the washer to perfection. Sadly, time wasted. Once I was done, I first did a wash without clothes, and then with clothes in Normal, fast spin cycle with drum about 2/3rds full. Just pants and t-shirts. There is a recirculating pump at the top of the drum to distribute the water, and to also distribute soap mixed water. But I am not sure if this is without problems. These pumps can collect soap residue with time, and you will eventually end up rinsing the laundry with soap mixed water even in rinse cycle.In getting to the first spin in wash cycle, I was flabbergasted to see how, just how rudimentary, I want to reiterate the word rudimentary, the load detection was before entering high spin. Our nine-year-old washer had a more comprehensive one. The new washer would spin the clothes at very, very low spin and simply see if the drum is most evenly spinning. That’s all. Compared it to our old washer which would also shake the drum to see if there was movement from side to side, because clothes can change their position when entering high spin. This rudimentary load detection causes the new washer to create an even worse uneven load distribution around the drum before spin, even though it may seem even at very low RPM. So, why is the new washer’s load detection so basic? I believe it is due to ball bearings.Front load washer models from other companies employ ball bearings to reduce vibrations from uneven loads. Whirlpool does not employ such feature, at least, they do not advertise them. However, to my surprise, I hear metal balls hitting each other every time the drum direction changes during the wash cycle. I inquired Whirlpool about this and I received contradictory responses. My theory is that the basic load detection before spin speed is used because Whirlpool assumes any changes to load distribution will be taken care of or reduced by the ball bearings of the washer. But this ultimately allows the washer to go into more uneven spins. The bearings may also be used to increase the tolerance of what is considered an ‘unbalanced load’ in order to get the washer to go into spin cycle faster, decreasing the time involved of the washer to go into spin cycle. Sadly, to my dismay, the new washer ended up causing a worse vibration than our old one with failing bearing.I called up the retailer the same day of delivery and complained of vibration. He first sent an installer to see if it was installed properly, and upon showing the installer of the vibration issues, the retailer sent me a new washer couple of days later thinking the first one was a lemon, and even though it has less noisy draining noise, it too exhibited the same issues with it going into significantly uneven spin. In the end, we decided to return the Whirlpool washer all together, at a loss of $200 because the retailer did not hold up to their spoken return policy.We have done many loads in this washer to see if our loading is an issue, loads of varying sizes, loads of varying types, loads of weights, and we maybe only had an evenly distributed load around the drum about once or twice. Once it was a King comforter. But, like our old washer, this too ended up not distributing properly around the drum in the final spin cycle and started vibrating, even though it was vibration-free in the previous high spin cycle. This proves that the problem exists directly within the washer, not the floor, leveling, load, etc.Some other problems with the washer: - The washer door, Load & Go dispenser at bottom, and single load dispenser at top are all plastic parts which all vibrate significantly during fast spin cycle. Especially the Load & Go dispenser which keeps hitting the cabinet to make banging noise. - Drain sounds are much, much louder than our previous Duet. It was even louder in the first one we received. Combine this to uneven spins and this washer can perhaps compete with an engine in terms of the sound it generates. - Single use dispenser at top left will hit the washer door if washer door is opened when the dispenser is also in open position. - Buttons are sometimes unresponsive, to which I have to power off and try again. But this has only happened a couple of times.- There is a small ¼ in. opening where the steel drum meets the rubber gasket, opening in which items like coins, etc., may fall through and are irretrievable. Don’t think small socks would be affected.To potential buyers, I suggest you proceed with caution when it comes to this washer. Understand the retailer’s appliance return policy and make sure it is shown in paper. It can save you a lot of headache. Get the extended warranty of three years because manufacturers only give you one-year warranty for a reason. I would also suggest that you avoid this washer at all costs if you have any floor level below where this washer is to be installed, especially if the level below is a basement. Your house is more important and more valuable than a $1000 washer.In the end, I am very disappointed in Whirlpool, an American company. Perhaps Whirlpool focuses their attention on top loaders, not front loaders. But Whirlpool had nine years to improve their washers, and it is sad that we may now have to go outside of America for a quality product to be used in American homes. P.S. No solicitation please, Whirlpool. This washer is in the process of being returned. P.S.S. I already posted this review in Whirlpools website, and it is under moderation.

I purchased a new home 1 year ago, our home came with Whirlpool Appliances. I was so excited because we were renter. The refrigerators after a year all of the LED lights have gone out, and the refrigerator make a very loud noise. I have called customers service several times. Their respond is, Sorry. It only has a 1 year warranty. The cost of the light would be over $500.00 dollar and that dont included labor. Dont even know the cost of fixing the loud noise. I just want people to be aware of Whirlpool appliances. After only 1 year of service it not going to work. Whirlpool will not fixed them. It sad we work hard to get a home and how will have to spend a fortune to get them fixed. Whirlpool you need to make better equipment. With is coming without home we were not giving an opportunity to buy an extended warranty.

Buy anything else. This WHIRLPOOL WITH STAINLESS INTERIOR WDF560 SERIES is the worst dishwasher Ive ever owned. Huge fail Whirlpool. MADE IN THE USA! I will never buy another thing you make again. I cant say ONE redeeming thing about this dishwasher. I hate it! It has a high temp wash, a Sani cycle & heated dry + a stainless tub. Using all of the above + having an SS tub yet everything comes out dripping wet. The cheap silverware baskets are poorly designed & positioned on the side to the back in addition to a tall tub making it difficult to access anything in them. The baskets are also cheap and poorly designed. All the spacings are the exactly the same with no proper spacing for pots, pans or larger items. These cheap racks will have a short life. Its outrageous to spend 649.00 for such an inferior product. Buy a cheap dishwasher! This thing is no better than a builder grade that looks good.

Sears, Whirlpool Cabrio Platinum washer and dryer purchased spring of 2013. I thought this would be a good combination to purchase quality appliances that would last for years. NOT! These machines are used by my wife and I only. Washer: Bearings go out. Repair: Replace tub and bearings. Quote: These things arent made to last more than about two or three years. Another quote. Do you notice that your clothes arent getting dry? Yes. Yeah well, you have to use the timed dry setting because the regular setting shuts off as soon as it senses one piece of clothes is dry and leaves the rest of your clothes damp. DO NOT BUY.

We purchased the Cabrio washer and dryer due to the companys past reputation and our own past experience with Whirlpool appliances fully expecting to receive great performance and durability. We have had the pair just about 2 years and the washer started experiencing problems during the spin cycle. The unit would get out of balance easily and then it would stop without spinning, leaving the clothes very wet. Well, as our past experience had indicated to us the washer is usually much more reliable than the dryer, or thats the way it had been for us. So we only purchased the extended warranty on the dryer. Not being covered on the washer we located a local technician and he promptly diagnosed the problem as the transmission failed causing the noisy bearing and the failure of the unit to spin properly.Our tech quickly repaired the unit but this failure disappointed me to the point of contacting Whirlpool. Thats where I came upon this site and saw the multitude of complainers with the same type of problems and some that are worse than ours. Our purpose in this review is to add to the 1100 or more reviews that report the same kind of issues. We are now in the same mindset as the 1100. Will we ever buy another Whirlpool? Probably not, especially since it doesnt look like Whirlpool wants to stand with their customers to make it right. Customer support is just as important to us as the reliability we seek. I would much rather spend a bit more in the price than replace or repair the unit after the purchase. A little economics lesson for our friends at Whirlpool is that if you abandon your 1100 customers you will save about $440,000.00, but those 1100 will tell everyone they know of their problems with that product and as a result many thousands will never purchase a Whirlpool. So if we all influence 5 of our friends not to buy, then 1100 X 5 = 5500 people X an average price of $800 which equals about 4.4 million dollars of lost sales. Seems like a no brainer to want to stand behind your customers. We dont believe that any washing machine on the market should fail after a few months to 2 years. These products should be built to last many years and the maker of these products should have that goal.

We purchased our Whirlpool french door refrigerator with bottom freezer from Lowes. A few months after purchasing, we noticed a pool of water on the floor, resulting from what looked like a leak coming from the ice maker. After contacting customer service, they sent a repair company to service the fridge. This rep stayed no longer than 5 minutes and barely looked at the appliance. He said my refrigerator was not under warranty, which was **, as I personally registered the refrigerator the day it was. My kitchen floor is ruined as a result. I will NEVER purchase another product from this company again. They seemingly left a faulty product on the market and failed to inform me about the known issue. Then they failed to quickly provide needed repair or replacement in a timely manner. They also refuse to reimburse me for the food loss, which would not have ever occurred had they handled the issue appropriately from the beginning. TERRIBLE company. In addition, since Lowes is aware of the reputation of this company and continue to sell their defective products... I will not be shopping at Lowes anymore! Both this companies should NOT be in business!!!

I installed this Whirlpool Gold Series oven in December just before Christmas. I cooked a 9lbs Turkey for over 4hrs at 350 degrees (it should have only taken 21/2 hrs at 325) used a thermometer to test the temp. Well the breast part was fine but later in the evening I removed the entire turkey only to find that the legs, thighs and bottom of the turkey was still RAW. Lucky no one had asked for that part of the turkey. Next I tried a small prime rib roast. Same thing happened. The top of the roast was fine and the bottom was RAW. I dont dare cook anything in the oven now. Called whirlpool and they are going to send someone to look at it but I wont hold my breath for any results. After reading the same complaint on several reviews and the TV show Marketplace it seems to be pretty standard for this product.

The washer buttons stopped responding after 19 months. Lid lock sensor didn’t work. Replaced control board because new sensor did not fix it. Went bad again after a week. I have to replace it. I think 1 year warranties are not enough for a major appliance.

Purchased a self-cleaning Whirlpool oven - model number RBS245PRS06 at Home Depot. Spent extra for the self-cleaning feature. The oven had slight use and used maybe once a week. Cooked a big Thanksgiving meal and decided it was time to use the self-clean feature for the first time. One hour into the process the oven shuts off, no longer has power, and the oven door is locked and will not open. Called Whirlpool (talked to 2 levels of customer service), they wanted me to buy a $200+ warranty for another year of coverage!Researched online and talked to the parts people and this is a KNOWN defect. It happens frequently when using the self-clean feature. It requires replacing the Thermal Overload Safety Thermostat which costs $45 with shipping for the part. The service call is over $100 PLUS labor which can run even more. There are YouTube videos that show how to replace this fuse. The parts lady recommended NOT using the self-cleaning for this oven. Buyer beware. If you are in the market for a new oven do not consider this Whirlpool model. THIS PRODUCT IS DEFECTIVE AND WHIRLPOOL WILL NOT STAND BEHIND IT ONCE YOUR 12 MONTHS IS UP.

Whirlpool stove and dishwasher very good quality. I find that the quality is beyond excellent for the amount of money. I would highly recommend Whirlpool. Easy to clean, heats up fast, looks beautiful. I would never change Whirlpool for anything else.

Bought side by side in 2010 and after the first 3 mth the ice maker jammed up. Found out the dispenser door was not working right so it was change. But lo and behold the dame thing jammed up again within 3 weeks and the door is working. I will never buy WHIRLPOOL AGAIN. I hope they go out of Business. They are selling junk and they do not care. Made in American. Pack your bags Whirlpool. You are no longer needed.

Like everyone else here, I had to call a repairman to have a look at my washing machine after 4 years of limited use (only my husband and I). As soon as the repairman looked at it, he told me theyve had so many calls for this particular washer. He ordered a new part for it, but it did not fix the problem. Thankfully we purchased extended warranty and we were credited the full amount + tax. Today I picked up a brand new Maytag washer. Cant wait to try it. Thanks Leons for the great service.

I like the fridge raider. It works great, I have had no problems. It has good space in the fridge raider part, but very small freezer. It’s a freezer onto fridge raider on the bottom. I would like more space in the freezer area. I would buy another Whirlpool.

No response from Whirlpool, but I did find out what the rust was. Instead of using stainless steel or plastic or rubber, the inside light frame is made of a cheap metal that has rusted and is literally falling apart, sharp and very rusty pieces were falling into the washer tub. No wonder I find holes in the clothes that werent there before washing. I removed what I could, including the part it should hold, a plastic plate that covers the light, protecting it from moisture. My husband covered it with electrical tape to prevent injury and possible electrocution. I contacted Whirlpool, but they have ignored my questions and have not answered. They do not have a replacement part for it (stated on their parts website) They give you no solutions to a problematic appliance that should have been recalled and taken off the market due to safety issues that have caused injury and possibly worse.

I had a Whirlpool dishwasher for year and it worked great, but the baskets were rusting. I decided Feb 2014 to purchase another Whirlpool dishwasher. It did not clear as well as my old dishwasher. The seller of the dishwasher stated it was our water or detergent. The water and detergent were the same. The only difference was the dishwasher. Day prior to changing the dishwasher, the dishes were clear and the day I changed the dishwasher, the dishes were not clean. November 2016, the main board has gone out. The part costs $148, plus the service call. I called Whirlpool. They stated they would sell me the part or would discount a new dishwasher. I think they should discount the part!!! Whirlpool makes most brands of dishwashers, so you cant change companies. Their quality is all you can get.

I bought a Whirlpool Cabrio Platinum washer 2 years ago and it is by far the worst washer I have ever owned. Its a water saving device with extremely long cycles. The clothes dont get wet enough, dont come out clean and they do not smell fresh. I have to put them through 3 rinse cycles and often times have to re-wash my clothing. The cycles are very long, using more electricity, and it takes me 3 times as long to get my weekly laundry done. My clothing comes out more wrinkled and twisted causing longer time ironing. My old agitator style washer did a superior job compared to this piece of junk. I dont like the automatic locking lid, nor do I like the machine choosing the spin cycle for me. There isnt even a soak cycle. If I want to soak my things I have to do it in the sink and then drag them to the washer to rinse and spin them.I spend a fortune on laundry additives in order to get my clothing clean and then they arent as clean as with my old washer. I now dread doing laundry and every time I look at the washer I feel like taking it to the dump! There isnt anything I like about this machine and I wouldnt recommend it to anyone. It is a piece of crap. This is 2016 and they havent learned how to make a good working washing machine. When I move, I will be celebrating leaving it here! I will never, ever buy a product made by them again.

Had a part come off right after our purchase but was a easy fix to repair. The silverware basket also kept coming off until we looked at it and realized it was on wrong. This dishwasher is much quieter than our last one. It also shows fingerprints. We got this dishwasher in a group purchase during a sale at Lowe’s that included the refrigerator a stove, microwave and this dishwasher.

About five years ago, I purchased a top load Whirlpool Cabrio washer and matching dryer. For the past couple of years or so, this washer gets out of balance every spin cycle. It sounds like a mac truck running through my house. At this time, I do not have $300-$400 to buy a warranty when I feel that this problem is so widespread (via internet complaints) that Whirlpool should fix this problem. I replaced a perfectly working 13-year old Maytag washer simply because my dryer went out. I have contacted customer service with no results. I recommended this washer to my neighbor about a couple of years ago and now I am sorry I did. Little did I know that three years in there would have to be a repair. As you know, this isnt a bottom of the line cheap washer, therefore, I wouldnt expect it would be acting like one after this period of time. I asked Dave who at Whirlpool cared and basically, he had no answer. I told him that I would expect a company as large as Whirlpool to have people who have the job of searching the internet to see what people are saying about the company and if they did, they would know this was a problem with these washers and would initiate some sort of recall. This is such a bone of contention at my house that I wish the thing would just die so I had to go buy another (and trust me it wont be a Whirlpool). But rather, I get to listen to my washer thrust throughout my house every load I do.

I bought my new ceramic top electric range/oven with convection, and the aqua-lift cleaning system in spring 2017. The aqualift cleaning function is a joke, so be prepared to be down on your hands and knees scrubbing. Im careful, and Ive not spilled anything yet, but the oven still gets splatters from roasting meats, etc. Id hate to see what Ill have to deal with when I actually let something spill. Today, as I was down on my hands and knees trying to clean it, I noticed that the enamel is chipping off where the oven racks slide in. Great. I have never had an oven where the enamel came off, much less within a year. I am struggling with heart failure, and I am not up to fighting with Whirlpool.

I purchased this Refrigerator Model #wrb322dmb, bottom freezer, 21cu ft. last year on July 3, 2015. In September I noticed rust spots on the top door. I called Home Depot where I purchased and they directed me to Whirlpool. I did purchase an extended warranty with Home Depot. Whirlpool did replace the top door. Thought that took care of it. Today one year and two weeks out of warranty, I again notice rust on both doors. Called Whirlpool. They said too bad out of warranty, not considering I had a previous report of this very same issue. So since I am very unsatisfied with this result and the fact that an expensive product is rusting, I decided to share to try to prevent someone getting stuck. Stainless steel is not supposed to rust which leads me to believe that it is not Stainless steel, but a Stainless Steel finish and not a very good one. So I am stuck with a rusting $1200.00 refrigerator only after one year. I have always purchased Whirlpool, but no more. They lost a 40-year customer. I have always bought American made but no wonder people are not buying American made any longer. TO SUM IT UP WHIRLPOOL STAINLESS STEEL APPLIANCES RUST! DO NOT BUY!

We purchased the Whirlpool model# BFG1J4040T3NOV 40 gallon natural gas hot water tank in the spring of 2010. The pilot light went out this weekend, 2011. And it will re-light but does not stay lit. This was bought at Lowes, rated as a 9-year warranty on the tank and parts. This is premature failure of a product that is listed as 9 years. Due to all the other similar complaints of this Whirlpool hot water tank, I would like my money back plus installation. I do not want the Whirlpool replacement as obviously it does not work. I will use a different brand and vet it much better in the future. We almost purchased at Home Depot but decided it would be a better bet to go with the Whirlpool reputation and name and Lowes than with the only Home Depot option, which is the self branded water heaters. It was a big mistake!

Large tub capacity. Door opens wide without stopping. White Finish has not faded or chipped. Quiet and rarely makes noise even when overloaded. Machine bought 12 years ago and has never needed a repair visit. It has been moved from 2 different locations by using the special brackets. Easy to use detergent holder and fabric softener.

Model GB2FHDXWS04 - This refrigerator dumps water all over the floor at least 1 time a week. We just leave a towel on the floor to absorb it because you never know when it is going to happen. Have removed the stuff and cleaned all of the ice out of the bottom of the fridge but in no time it is back. What a crummy unit. I am going to drill a hole in the bottom of it and put in a drain I guess.

The washing machine is so loud when it is on, drowning out conversations esp when cooking or eating (it’s located in the kitchen). The machine tumbler has to be constantly readjusted no matter the size of the wash or how many times my husband or myself adjust the tumbler; consequently the washing machine is always dancing, making a horrible banging noise. The washer is under 6 years old. With that said, when you open it, the lip is all rusted out.

Everything I buy from this company breaks all the time. I purchased these brands hoping they were good but apparently not. Always have to get them serviced. Lately they did an exchange on my fridge. Hope it helps because after thousands of dollars of food in the garbage it better work. And the washer thought, Oh Im paying more. It will be good. At this point will cost me less to buy from another company. Buyers beware. Cause the company cant do nothing good for me so dont buy from them.

Whirlpool Cabrio Washer Model WTW6400SW2 Serial CU0272414: I replaced my wonderful 25+ year old Kenmore washer with the Cabrio, 4 years ago. Within the first year I had to have a computer board replaced that was covered under the warranty. This last 6 months I replaced the suspension rods, was constantly showing that the load was unbalanced. Also have a LD error, long drain, probably because a sensor is bad. Today, restarted a load several times and could never complete the entire cycle. I resorted to unplugging, and starting a drain spin cycle and the washer just flooded my house. So Im done with this unit. Waiting for a class action suit. Lets get started. What type of unit should I buy now. I guess Im going to subscribe to Consumer Report before I buy another. Laundromat for me in the meantime.

I purchased a Whirlpool water heater and after working fine for about 2 1/2 years, I began having problems with it staying lit. I dealt with troubleshooting beginning in January of 2012 and finally in March of 2012, I was sent some replacement parts. The unit worked fine through the summer and once the weather started getting cold in October of 2012, I began to have problems with the unit again. After a couple of months complaining and threatening to file a BBB complaint, I was sent all of the parts left to change on the water heater. And I was told after the parts were changed if the unit still did not work, that it was probably a venting issue and that I would be responsible for that issue and the unit was not defective. I received the parts on 12/04/12 and they were changed out the same day. Now the unit will light when I hold down the button to light it but once I let go, the pilot light goes out. At least before changing out the parts, the unit was able to be turned on and sometimes it would work and other times it didnt, but now it will not light at all. This is very frustrating because the unit is under warranty and Whirlpool has for an entire year fought me tooth and nail just to send me the parts for the unit, only for the unit to still not work. I have a family and it is discouraging to not know when you are going to have hot water, having to constantly fix the unit or to call Whirlpool to troubleshoot and finally for the unit to still not work after replacing the parts. It looks like I will not have any hot water at all now.

Whirlpool WRF989SDAM00. We bought this junk April 22, 2013. 7 visits from service guy throughout the entire year we have had this, problems began almost immediately. Whirlpool gave us a 3 month complimentary warranty (which is up at the end of June). Same problem is back (back left corner freezing up and I think it has also made our ice maker not work nearly as good as it should). We called a few weeks back to report problem yet again, the rep on the phone treated us very poorly. They said they have a new part that is currently on back order that is going to fix the problem once and for all to which my husband replied: I do not have much confidence this will fix the problem as you have sent 5 or 6 new and improved parts over the year and all has failed. He then asked, will you extend the warranty once more, and they said NO. We are stuck with a ($2,700) piece of crap that they just keep trying to find new parts to fix it! On a separate call we asked for a refrigerator replacement to which the rep basically laughed and said that will never happen!! What course of action can we take here?? This company is dead to me!

I purchased a Gas Stove from Home Depot on 11/23 and it was delivered on December 3rd. My God, Im having a dinner party tonight and the stove doesnt heat up past 170.. Unbelievable!! Need a replacement gas range. Tried to chat and call Whirlpool unsuccessfully. I am very one disappointed customer right now!

I purchased a Whirlpool 3-door refrigerator with the freezer on the bottom on 8/17/12. Within 4 days, the ice maker stopped working. It took two days for the repairman to come out and fix it. So all is well with that. Less than 2 weeks later, the refrigerator isnt cooling. Several days later, the repairman came and determined it was the evaporator fan motor and clutch. The parts were back-ordered for 10 days. Parts came in 2 more days before he can come out and install them. He realized they sent the wrong parts. Another week went by, then he came and replaced the fan motor, which is now making an ear-piercing buzzing sound. He came back a week later and said it needed a gasket, which is back-ordered. In the meantime, he put some stick on insulation around the unit. Not much help. Another week went by, and the gasket showed up. It is still making a high-pitched whining sound. He said it was the compressor. Whatever! I hate the refrigerator. The sound is one that just grates on your nerves and you can hear it in all the rooms surrounding the kitchen! A repairman has to deem it unrepairable before they will even consider replacing it. They consider it fixed. What about my bleeding ears! I just want it gone! I am so disappointed. I thought Whirlpool was a good product with a solid reputation. I have a $2300 noise maker! Is there a class action lawsuit?!

My Whirlpool dishwasher is only 2.5 years old. The first 1.5 years we were not full time in the house, so the dishwasher has not been used much. The touch pad went bad already and it was $450 to fix. Whirlpool sent me an email after I vented and it was a cookie cutter reply. They dont care that the appliance was manufactured with a faulty pad. We never buy service agreements because we feel an expensive item like this should last the term of service agreement if made correctly. No more Whirlpool purchases for us!

DO NOT BUY THIS MACHINE. Mine is less than 2 years old. First one month after warranty expired, the clear lid cracked...$350 to replace! Then a few days ago a rusted circuit board came apart and jammed up my washer. This should NEVER happen. I contacted customer service and they told me that they are not covering this problem and that the service call is $175 and cannot estimate the repair cost. They also could not send a repair person out for 5 days. The washer has not been repaired yet so I do not know the entire cost but it will be expensive!

I purchased whirlpool Model# WFG540H0ES gas with convection. I purchased it because the price was $1000 dollars less than comparable ovens and even now the price has gone up $300 since I purchased it. I really wanted the luxe look at a discount price, a burner that you could lay a grill over, and five burners which it provided all of those things. I hesitated to buy this oven because the door fell off the last Whirlpool within three years and they refused to fix it so I tried not to buy this brand but it had the amenities I wanted for the price I could afford. I really like the oven. I like the oven the best because it really does make a great cake. I like the two large grates that sit across the oven. It makes it feel high end. If you dont wipe the range immediately grease gets stuck on the range and is hard to clean. This is what I like the least. Im ready to wipe on the weekend and its too late. It took me four days of internet comparison to decide on this one. The house is not painted, the cabinets are falling off the wall literally but I am extremely proud of this oven and it makes me feel affluent even though Im not.

Whirlpool makes a quality product. My gas range is 25 years old and it still performs like new. I’ve never had to have it repaired and it is used daily. If and when the time comes that I need or want to replace it, I will not consider any other brand.

I bought a Whirlpool front loading washing machine 5 years ago, which has given me constant trouble. The computer on the machine is not working. When it is fixed, the machines makes extremely loud grinding noises and frequently the spinner does not work properly, leaving you with heavy sodden wet clothes. Whirlpools guarantee is very limited and customer service is unhelpful except to apologize for your horrible experience. You will have to pay for a technician to diagnose the problem. I will have to replace this costly machine after just 5 years of unreliable service. I would never buy a Whirlpool product again.

Whirlpool dishwasher Wdt790slym1 - This is the worst dishwasher I have ever bought. The top rack assembly is made of all plastic and started falling apart within 13 months of purchase. I have had to order the same replacement parts numerous times and have reached the end of my patience. Buyer beware!!

Hot water heater goes out. Try to relight it as instructed. Pilot light goes out as soon as I release pressure. Call tech support. After a 10min hold time, I was instructed to rest unit, wait 10 to 15 min and try again. Did not work. Called back and was told it was the thermopile. Had it shipped and replaced at $45.00. Still did not work. Was instructed to go thru the same process of lighting it, still did not work. Then I was given a ref# and was told that my PARTS was warranty and not labor. Okay now one time I was told I WILL BE CHARGED WITH A DIAGNOSTIC FEE OF $99.00 and still no hot water. Next step LAWYER.

Ice machine went out right after the year warranty was up. Convenient right? We called a hometown tech to come out and look at the water valve. He was unable to locate it, so we called Whirlpool service. After waiting 30 mins, they told us they cant tell us where to locate it for safety reasons, and if we wanted anything done to the refrigerator, we needed to pay a tech to come see it. EXTREMELY RUDE!!! I would NOT recommend whirlpool ANYTHING.

(Model WTW5640XW3) Whirlpool Cabrio worked Good for 11 months (just after warranty Expired). Replaced capacitor would not spin, hums loudly and smells like burning Plastic. Then about 2 months after that Lid locked, failed, replaced. 7 months then Actuator failed and now looks like the Main board give up. I dont know where The original parts are made but they are Cheap junk. New technology is crap for Washing machines, gears transmission and Solenoids last a lot longer plus they clean your clothes. And belts and solenoids.

I bought the Whirlpool WTW 5000DW1 washer and dryer to go with it. Within the first 2 weeks the plastic handle broke on the dryer. Ive been using the corner of the plastic handle ever since to open the dryer. The washer is the worst washer I have ever purchased in my life. The tub doesnt fill up over the clothes half the time. It is perfectly balanced on the floor but it always bounces around and you cannot open it to rearrange the clothes because they lock the lid. The only option is to try to hold it and wait for it to finish or start over by pressing the button for at least 3 seconds. I have had a few items get shredded by it and a lot of times the clothes dont get cleaned and rinsed properly. Even on 2 rinse option. Just the fact that it has a 2 rinse option is a big red flag. It is supposed to be a energy saver and water saver but that isnt true. If you have to wash and rinse the clothes twice because it has spots from the detergent still on the sheets, something just isnt right. Whirlpool shouldnt even put a product like this on the market. I have owned many Whirlpool products before this but this is the last Whirlpool product I will ever buy. Obviously Whirlpool doesnt test its products or care about quality.