I have had a plumbing company work on my Whirlpool water heater three times in the last two months. On the third visit, he told me all the problems customers have had with Whirlpool water heaters. I decided to call Whirlpool for warranty purposes. The unit is three years old. I was told that it was the gas valve, and I was given a free one from Lowes. After installing the new valve, it still did not work properly. After troubleshooting with a technician, I was told it was the orifice. I have had to do all the labor myself, and I dont know how long this is going to go on. I have heard Whirlpool will continue to give you the runaround (from the plumbing company and Lowes salesmen) and will continue to give you the runaround and not replace the unit. They are wearing me down. I have been without hot water for three weeks with no end in sight. I am ready to give up and just buy another water heater but certainly not a Whirlpool.

Best stainless steel built dishwasher we could find in this price range. Well built with lots of room and easy access to both drawers. Easy to clean filters and a nice modern look.

The microwave keypad is worn down after 10 uses making it difficult to read the pad. I just discovered the microwave was missing the front leg and they do not have a replacement part so I am stuck with a virtually new microwave that will not balance. It took 4 phone calls to their customer service department to try and sort out the problem. Poor product and extremely weak customer service department.

This will be the last Whirlpool appliance I will buy. We purchased this Whirlpool refrigerator Model # ED5GVEXVD literally a few days over 2 years ago. It is a side-by-side refrigerator with shelves that are supposed to slide out, however, we have never used it in that capacity. The problem is that the plastic frames on every shelf, even the ones that do not slide out over the bins, have cracked in no less than 2 places on each shelf.We contacted Whirlpool over a month ago. The good news is that they responded quickly. The bad news is that they stated, It is unfortunate that you had problems with the shelves, but we are unable to do anything for you because it is out of warranty. If you would like to purchase replacement shelves, we could order them through their consumer parts department. This is such a crock. If it was one shelf, I could justify the possibility of it getting smacked or something overweight was placed on it, but every shelf? As I said, not a single shelf is crack free, including the ones that sit directly over the bins, which should have additional support from the bin construction.By the time I replace every shelf that is cracked, it will be equal to what I paid for this refrigerator 2 years ago, and it will net me maybe 2 more years of service. If I have to invest that kind of expense into it, the refrigerator will go to the recyclers and I will buy from another manufacturer, which will definitely not be a Whirlpool or Whirlpool subsidiary.The cracks were noticed early last month. The cracks are already getting larger. I will no longer allow my children to get anything out of the refrigerator since Im afraid that the shelf will crack, the glass in the shelf frame will break and we will have an injured child, which instead of reaching this website, I will be contacting a lawyer. I need to do something with this refrigerator, but with the economy, I cant afford to just keep replacing a $1,000 refrigerator every 2 years.This refrigerator does not get extreme use since it is the 2nd refrigerator in the house. The primary fridge has been in our house since 2005 and I wouldnt trade it for anything. This Whirlpool refrigerator, however, is poorly made. The materials that the refrigerator shelves are made from were just a poor engineering decision because it is not holding up to mild to moderate use without cracking.We purchased this Whirlpool appliance thinking we were getting a quality product from previous reviews we had read, however, this is obviously no longer the case with this company and seeing the complaints that I now see online. Someone would have to give me really compelling evidence to make me decide to ever purchase another Whirlpool appliance again.

I bought a Whirlpool Dishwasher, Model No. GU3600XTVY in July 2010 for $844.30. In August 2011, it failed to clean dishes. The repairman said it needed a new heating element and computer board which costs $319.92. Today, he installed the new parts and it still wont heat the water! Now he wants to take it in to the shop to check the wiring.My previous Dishwasher was a low quality builder-installed GE that lasted 16 years without repair. If we Americans accept that 1 year is an acceptable life span for consumer products, we will continue to have this type of trash sold to us. Made in America is now the product you dont want to buy.

I bought a whirlpool microwave on August 8th. The microwave was missing parts. I called whirlpool. They said they were sending me the parts, mind you this was not a floor model. So 2 weeks later pass I received no bracket No screws. I called whirlpool oh yes we got the address wrong. Resent it, just one screw no bracket and I needed 2 screws. I called again oh yes we did get the order for the bracket too but you have to pay $7. I said ok no problem. Can you do fast shipping? They said sure. I called Monday August 25th. They said I should receive it by Wednesday August 27th. I had to pay extra for the shipping. Here I am September 2nd w/ no bracket. Called again. They said it wasnt next day shipping, it was 2 day shipping and its at the post office. But the shipping number they gave me was for the one screw. I believe I should get my money back. I spoke to a supervisor, took her number down. Still waiting for a call because the mailman came and I didnt receive anything yet again.

Why are the Whirlpool appliances so badly made that they are not fit for normal use? Are they buying substandard parts? Do ConsumerAffairs advocate for more robust, long lasting products, particularly with current sustainability concerns for the world? Having to buy a new motherboard and burners, cups and knobs after a couple of years of normal, careful use, is unacceptable, surely? The motherboard, burners and fitting charge is almost half the cost of a new appliance (gas range). Is this acceptable?

I purchased a Whirlpool Cabrio Washer in May of 2009. I do laundry for only 3 adults, so I never run more than 3-4 loads a week. It constantly is off-balance when spinning and requires positioning the load again several times before it will continue its cycle. Now 5 to 8 minutes into it filling with water, it stops filling and beeps, and code F shows up on the screen. Also, during the spin cycles, it is very loud and fast. It sounds like it is about to take off anytime. I called customer service to no avail. They just wanted me to schedule a repairman to come out and fix it at my expense. Now, I know why they only give a one-year warranty - they know it will last one year but not much longer. Im from a generation of people that is used to appliances lasting 10 - 14 years and the company stood behind their products and didnt ask you to buy an expensive extended warranty for the 2nd year and so on. If inferior products were not manufactured, there would be no need for an extended warranty. Anyway, Im not going to put any money (I was quoted a $129 charge by Whirlpools service department just for the diagnosis of the problem which didnt include the labor or parts costs.) into a washer that will probably continue to have problems and become a money pit. Consequently, I will never buy nor recommend anyone buy Whirlpool appliances. It would get quite expensive buying a new washer every 3 years or buying the extended warranty plan. The matching dryer had no major problems, but a couple of years ago, I had to have the door changed from opening from right to left to opening from left to right because the door catch broke on the right side. Hopefully, nothing else will go wrong with it in the near future.

The wash machine is JUNK. We paid $2500.00 for our washer & dryer at lowes in 2012. I HATE IT from the start. It has destroyed most of my clothes. I hate doing my clothes. The water does not get my clothes wet, they dont get them clean AND the washer dont even get them wet. THEY need to do a recall or get us a lawyer. ALL the money I have put in this washer. The price we paid for them is a SHAME. IT is WRONG they are telling people that this washer is the best. They lie. I HATE HATE THEM.

I purchased a 12 year warranty, high end Whirlpool WATER HEATER (OR SO I THOUGHT AT THE TIME) through Lowes in 2014. Model ND50T122-403. Six years and multiple service calls later it is broken again, this time for the final time. I am ripping this garbage out. So livid with this company that could give a rip about their customers. Three years in to my 12 year warranty it started giving me problems. Horrible HORRIBLE customer service. They will insult your intelligence. Whirlpool will not honor the warranty or stand behind their product. They just take your money and basically give a shrug of the shoulders or worse blame you for THEIR TERRIBLE product failing. It may be unscrupulous and unethical but I guess saves them a pile of money which is what they seem to only be out.The Service Tech that came for the 4th time to repair it says they see this all the time in Whirlpool water heaters. Its a Design Flaw they say. I dont know about all that. I just know when I have been swindled. The electronics are garbage. The pilot light when it goes out is not easily reset as others have mentioned on this site. Will stay lit for while and then shuts down. Whirlpool says, despite reams of evidence to the contrary it must be a safety issue in the install, which they have absolutely zero evidence of therefore, they are not honoring the warranty. They are Blaming the installers, according to our service techs who tried to order the part thats supposed to be under warranty.The original installers, by the way were from Lowes, the outfit that sold me this hot mess. Another Class action lawsuit seems ripe. Or perhaps the consumer protection division from each states Attorneys General would be interested in protecting their citizens from practices like this. Lowes is complicit in allowing it, failing to protect their customers and not calling Whirlpool out for it. I cant think of a more deserving target of consumer protection than Whirlpool. A truly horrible, expensive experience. See the Whirlpool logo and RUN - - DO NOT WALK -- THE OTHER WAY!

I have always used Whirlpool washers and dryers. There are many models to choose from to meet a families needs. I can only remember one time when I had to replace an operating part to improve performance.

I purchased a home that came with Whirlpool appliances. I begged the company for GE or Maytag. Of course they went with the cheapest they could find. I must admit the microwave gets very hot but the dishwasher is a piece of crap! The water doesnt get hot and the dryer doesnt work. They tried to tell me it NEEDED Jet-Dry. I own 4 homes and have lived in all of them. Ive NEVER used Jet-Dry and all the others work perfectly. Run as far as you can from Whirlpool!

I bought a Whirlpool fridge in 2014 and started having problems a year later. It was making really loud noises and the fridge part wasnt working. All the food was warm. Of course there is no warranty on it after one year. I called a repairman and he said that the doors dont seal properly so the warm air is getting in causing condensation which freezes the engine/fan which is the cause of the loud noise. The reason why the upper fridge is warm is because the fan pushes the cold air up from the freezer, which of course wasnt working. Then I noticed that the frame at the bottom of the fridge is bending causing the freezer not to seal properly which would be the reason for warm air getting inside the fridge.

Lets just say Im not surprised by all the negative reviews on here. Im just one of many in the fishbowl! Been without a fridge operating for 6 weeks and still waiting for action, been on the phone with them everyday and no resolution. Although the service technician/provider is also not cooperating but my word, they wont buy me a new fridge of course and only offer a simple 50$credit and nothing else. DONT BUY WHIRLPOOL. Have had nothing but troubles with 2 fridges now!!!

Whirlpool dryer and washers have the worst reliability, plus terrible customer service. Parts missing from factory install to faulty parts that constantly need to be replaced. Wasting precious time to meet with service repair people. Not worth it. Make products that are reliable and be accountable.

I purchased a matching set Whirlpool Cabrio top load washer and dryer in 2007. Bought from Conns for $2,100. After 3 months of ownership, the circuit board had to be replaced on the washer. Three months later the heating element was replaced on the dryer. Just recently I spent $350.00 to replace 4 drum suspensions. The washer literally shook my home. 3 weeks later, the circuit board needs replacement (code F1). Estimate to repair - $325.00. The dryer is not working properly. Im having to run the clothing thru 2 cycles. Back to the washer. It shreds my towels. Ive read where other consumers have had this same problem. These are expensive towels. So, only 7 yrs. into ownership and I am replacing this junk with the old school washer/dryer. Unlike the Cabrio washer, I will have a washer with an agitator that will actually clean my clothing. Whirlpool manufactures trash and the Cabrio duo was the worse purchase I have ever made. Do not purchase Whirlpool and definitely do not purchase Cabrio.

In 2011, I bought in Croatia, for the start, 2 washers (model 3LCHW9100WQ) and 1 dryer (model 3LCED9100WQ) and opened the first self-service laundry in Pula, Croatia. Since the beginning, I had problems with the gum (black). After the washing cycles, you could see black lines on the laundry. Whirlpool Croatia denied that the gum can be the cause. After two months, they gave me new gums, but the problem still exists. After 5 months of work, the first malfunction on the washers started. The biggest problem is that it took and still takes them up to a month to repair them. And these problems I have ever since. Also, the error codes never showed the correct malfunction code. In global, if I take that I have these washers and dryer for about a year, they were out of function for more than 3 months. The warranty expired in April 2012. On these reasons, I cannot recommend any product of Whirlpool, and I have to change to another company to buy more washers and dryers.

Bought the dishwasher 3 years ago and now its not worth anything as its pump gave away. Cost to replace the pump is $200 or more so it doesnt make sense to do that since you can get a new one for $300-$400. Everyone I talk to say they are not building these as they use to and they give out in 2-3 years. I am very unhappy with this dishwasher.

This is our 2nd circuit board failure in the 4-5 yrs, since we purchased this very expensive range/oven. The first time was shortly after the warranty ran out and Whirlpool would not even send us the part for free. They said there was nothing they could do. So this time we are not even contacting them and are just having our repairman order another new one. For a $1600 range to have to put more than $400 back in so far, I would never buy a Whirlpool again. I have been very careful not to use any cleaners on the circuit board as I was told by our repairman that that shorts them out. First the convect bake button wouldnt work, nor the convect roast, now the bake button, so the only buttons that work are broil and warm. Even the timer is shot. What a piece of junk (electronically). Beware buyers!

Im 61 so I have some experience. I personally know fridges that have lasted over 20 years. I just Googled it and found out the norm is 14 to 17 years. This hunk of crap lasted 4 years. As soon as I got it home and plugged it in (4 yrs ago) the most noticeable thing was the noise. It sounded like a tractor! I considered taking it back (wish I did). Then after a couple of years the pull handle came off! The whole time we had to be careful the door was closing properly. It was problematic. Ive owned (and re-sold) about a dozen fridges in my life. This the first one to fail on me. It was bad from day one!

I purchased a Gold Star Whirlpool Refrigerator from Sears which was installed on July 1, 2010. The freezer was icing up along seams, so sealant was used. However, now I noticed after 14 months that the interior refrigerators lining is fracturing throughout the sides and bottom of the refrigerator. Not at seams but all over fractures, spanning 10 to 3 to 2 on the bottom and side of the interior lining of the refrigerator.Sears answer is more sealant, and Whirlpool does not take any responsibility in designing a defective liner since it is pass the one year time frame. This causes your refrigerator to be on more often, because of the cracks. Unfortunately, the consumer loses out. Both representatives were nasty and when I asked for a supervisor from Whirlpool, an incident report was written, however I will not ever be able to get a copy of it. It will be considered an internal document. It is a great setup between Whirlpool and Sears having defective appliances made to last a year, and Sears to win with warranty agreements for the life of your appliance of $250, for one year coverage. When you buy the warranty and have a lemon, Sears doesnt replace it, My suggestion to consumers is to buy a tube of sealant.

Purchased washer 8/2015. Washer quit working 12/2015. Would not drain or do anything. Repairman dispatched and came 3 business days later. (They dont work weekends.) Repairman looked at old receptacle cover and immediately stated, Problem with polarity of plug. No prior problems with plug running appliances. Plugged into it for over 8 years. When I advised him of that then he started troubleshooting circuit board. He cleaned out the machine and got it to work. (Still under warranty) 4 days from repair, and machine quits. Same problem. Wont drain and wont do anything. Call for service again on Weds. morning and given following Tues for service call. Online consumer reports complaints #ered at over 1,7000. Same machine, same problems. Call Whirlpool directly, given runaround. Talk to Whirlpool mgr. (Robert) complaint # **. He states, Have to wait for service. But calls Brandt Melb., FL to try to get sooner service. Brandt calls me stating they have ordered a lid lock and CCU board for machine and will be out Monday. How would they know to order these parts if it is not a constant issue? Im thinking class action suit for shoddy product... LOWES Indian Harbour Beach, FL. Transaction #**.

I called the dealers repair department, which said they had not seen this before and it looks defective. I have used the oven less than a dozen times. It is virtually new. They submitted pictures to Whirlpool. The oven surround is not replaceable, so the request is to get a new oven. Whirlpool responded with, This is normal... when the cracks break through, then there is a problem. What?! I have been cooking for over 50 years and have never had this experience before. This product is under warranty. By the time it cracks through, it will be too late to do anything about it. Since when is crazing on the oven bottom natural, especially after only a very few times used? This is defective and Whirlpool is shirking their warranty. I am very dissatisfied.

I purchased a top load Whirlpool Washer and Dryer in April 2021. When it was installed I commented about how noisy it was. I was told it was because it was empty, but it will be much quieter once you put in a load of laundry. That did not make any difference. I called Whirlpool customer service and explained I had just purchased it less than a week ago and it appeared to be very noisy. I was told they could send someone out, but if they determined there was not a problem I would be charged a service call. I said the machine is not even a week old why would I be charged a service call shouldnt this be a warranty issue. Again I was told there would be a service call charge.I am completely baffled at the customer service response. This is the first and only time I called. I contacted the store where I purchased both the washer and dryer and was told it should not be that loud, this is the first time anyone has complained about the noise level and there should not be charge. Whirlpool has terrible customer service and I will NEVER purchase another Whirlpool product again because of the customer service. I have purchased numerous appliances in my lifetime and have never been treated so poorly. If I could return both the washer and dryer I would not hesitate. I would not recommend Whirlpool to anyone.

I will be happy to provide exact details soon but wanted to share I have had most of our clothes and household items-sheets, rugs, towels etc. ruined by this machine. And it is under warranty and Lowes in Dallas, Texas where I purchased it has seen the evidence. I rolled in with a suitcase full of different examples of ruined items and some photos. The repair person Whirlpool sent out was nice but not willing to document clothes and said the machine is fine after a few diagnostics digital checks. He did not run a load of clothes! And it takes forever to set up. My wait was over 3 weeks. etc. Lowes has been incredibly wonderful but states the warranty is Whirlpools decision and all Lowes needs is a RA (return authorization from Whirlpool) and Lowes is happy for me to buy whatever ever washer I like and even are willing to give me a discount as they know how horribly Whirlpool has treated me.The manager stayed on speaker phone with me for over an hour. My husband is a lawyer and I will further pursue this situation as Whirlpool hopes I will just drop it by March when my Whirlpool warranty runs out or give up from protocol internal exhaustion. As they have insulted me in every way... Even suggesting I sell the defective machine to someone else... And I said, How in good faith and having a conscience could I do that? Anyway after spending a lifetime it seems trying my best to get this resolved with a cauliflower ear from being on the phone for so many hours with their resolution leaders and specialists etc. It is obvious I am about to have to go on social media and do everything I can to Save others from this time waster, Save their laundry, etc. and Did I mention at times it leaks a little bit of water out the front. As it was the least of my worries as I was showing nice tech my expensive ruined 900.00 ski pants, ruined shirts etc. I think the machine cost around a 1,000 to 1,200 so... Will get back to you for an update. I have a whole file folder on documentation now and it is not about the money or the fact I cannot wash clothes. It is down to principle... On my third top-level resolution leader in MI. -Jim- basically had me read between the lines that I was dealing with a Fortune 500 company and would never win. He is underestimating the level of frustration and lengths I will go to not be taken advantage of as a woman, a career girl, a wife and a yoga teacher. I will be in Yoga warrior mode and this is disheartening as all I want to do is wash my clothes. Did I mention all my Lulu Lemon pants are ruined and I never put them in the dryer! Only delicate cold etc. Have them remain intact etc. really simple here but Whirlpool not standing by their warranties. And my whole home is outfitted with Jen-air, Kitchen-Aid, Maytag etc. which are all owned by the same company so I have been a very loyal customer who possibly just got a lemon. Or standards at the company have severely changed. More later on developments hopefully. Sad in Dallas.

I bought my Whirlpool over the range microwave WMH32L19AS November 28, 2015. We started having problems with it, working intermittently one year later. I called Whirlpool in January 2017 and they told me it was out of warranty and it would cost $150.00 for a repair person to just look at it. I decided to just keep using the microwave because I only paid $232.00 for it and I figured after parts and labor if would probably cost over $200.00 to fix it. I called Whirlpool back in June because the microwave wouldnt shut off and even kept running when you opened the door. Whirlpool sent out a repair person at no cost to fix it. But the repair person told me Whirlpool only paid for him to diagnose the problem. I had to pay for the repair. After working on the microwave and replacing sensors and fuses he determined the microwave irreparable. I called Whirlpool back and they just told me that my microwave is 1 1/2 years old and they were not responsible after 1 year and I should have bought the extended warranty. I will never buy another Whirlpool appliance again.

The washer in this set is my biggest complaint. I have followed all instructions and tried different methods time and time again and the clothes never come out fully clean. I too experience all the other complaints on this site as well, stuff still left on clothes, dry spots, stains not removed after being pretreated etc. I did some research before buying this set and saw some good reviews, dont know who wrote them but obviously they were highly inaccurate. This is my biggest purchase regret ever, as this set cost about $2500, so disappointed.

My refrigerator is now 5 years old. I have a stainless steel fridge. I didnt even have my fridge for 2 months and the one door started to rust. Whirlpool did fix that but now my fridge isnt staying cold. My extended warranty was just up 5 months ago. Figured some of the repairmen that we have called wont touch our fridge because they say the model that we have breaks a lot and that Whirlpool discontinued making this model. I am disgusted with this fridge.

I had a Whirlpool GI7FVCXWY01. Purchase 3/13/2010. I had repairman after repairman come to fix it. The last one probably saved my family and my house. The light in the back corner was not only blinking, but flashing rapidly, much like some wild party light. It eventually stopped. The freezer works perfectly fine, the fridge works when it wants to. The ice maker makes ice some days but not others. The motor on the ice dispenser is completely frozen up. Does that all sound about right? If it does, clean it out and cut the power to it before someone gets electrocuted or your house catches fire.If you cant find the electrical diagram, or the company wants $455 to answer your questions, look under the right side of the freezer draw, but not on the draw. Remove the guard on the very bottom of the unit, near the wheels on the right side. You will feel a plastic bag attached to the underside. Inside that bag is the complete diagram of all the wiring harnesses along with the schematic for the amps and voltages for each wire. Are they telling your circuit board is bad and you will need a new one? Before you do that, inside the fridge compartment, in between the water filter and the ice maker, remove the light cover. Notice that inside that space is the access to another panel. Remove that panel. BE SURE THERE IS NO POWER RUNNING TO THE UNIT FIRST. Here you will find a connection plug with more or less 15 wires that are connected to the main wiring harness. Above that plug you will find a holding chamber. This holding chamber contains water from the filter that is waiting to go to the ice maker. It has dripped condensation on the plug since the day you first turned on your fridge. Your wires are most likely broken and corroded. You will need to have your unit completely rewired, but because of the design flaw that fix will only buy you another 4-5 years. My Whirlpool GI7FVCXWY01 left yesterday 5/15/2014 and none too soon.

I have Whirlpool 25 in. Side by side. I love the space freezer size is bigger than the old one I had. Makes ice as it should. Overall solid appliance that I trust. I purchased this refrigerator a year ago after research.

We purchased a new Whirlpool Cabrio washer, model #WTW6340WW0, and dryer unit 2 1/2 years ago. We did our research online; Consumer Reports got great reviews everywhere. We went to Lowes and was told that this set (washer/dryer) was the top of the line in top load washers, so we purchased it. Now 2 1/2 years later, our washer is out of service, bad power board is the suspect and maybe the pump. I have heard that there may be a class action lawsuit coming down the pipe against Whirlpool and would like to know more info if it is. We paid nearly $1,000.00 for the washer and like other complaints, we were led to believe that we would get 10-14 years service out of the unit. But that did not happen. I think Whirlpool, Consumer Reports and Lowes should all be held accountable for misrepresentation. I can assure you that all of their executives received attractive bonuses for misleading the consumer. I would not recommend Whirlpool to anyone, Consumer Reports nor Lowes.

My family purchased a Whirlpool stainless steel dishwasher at Lowes for around $500. We were replacing a very old GE dishwasher which was so loud you had to leave the room anytime you started it because you couldnt even talk over it. We love the new Whirlpool dishwasher. It is so quiet we thought it was broken at first because we couldnt hear it running and even though it cleans exceptionally well we still sometimes have to look to see that the light is on to know that its actually running. The whole family agrees this may be one of the best purchases weve ever made. The only con I could think of is my son and I put the dishwasher in ourselves and this is the first one weve ever done and the instructions werent as clear so we had to redo the piping of the waterlines a couple of times to figure out in what order to be done. But everything hooked up correctly and worked immediately without a problem. Couldnt be happier.

Think twice before buying Whirlpool appliances. In our experience, quality and durability are a real issue. Here is our story. 5 years ago we built a winter vacation home. We bought brand new Whirlpool appliances from a reputable vendor at full price. Washer, dryer, double oven, and refrigerator. The washer arrived damaged. The damage was a button that was depressed and could not be released. This was brand new washer, never used, but Whirlpool insisted that we had caused the damage. It was only after the vendors tech got involved that Whirlpool relented and sent a repair tech.Next, the bottom oven door came apart in my hands after just days of use. I had to fight (yes fight and argue!) with Whirlpool customer service to send a repair tech. Finally after much arguing Whirlpool sent a tech and the oven door was repaired. The tech told us that this was a common defect! (Shame on you Whirlpool!) So why you might ask, why am I complaining? Well this is a vacation home. We are here 3 months a year (times 4 years = 1 year of very light use) and today the oven door came apart in my hands again. That makes twice in 12 months of light use. Frankly, this is shameful! I do not understand how this company gets away with it!I am disgusted with Whirlpool crap quality and crap customer service and I want everyone to know what they can expect when buying Whirlpool. I suggest you check all available reviews before placing your order for anything from Whirlpool. As for this new oven door repair? Ill report again after talking with Whirlpool but I expect to be told Sorry sucker, the warranty is over! Buyer beware!

I like my dishwasher very much. Because we have hard well water I use Lemi Shine to cut down on any deposits. The top shelf is adjustable so that helps with large pans getting clean.

Bought this washer in May of 2019: Whirlpool - Whirlpool - 4.5 Cu. Ft. 37-Cycle High-Efficiency Front-Loading Washer with Steam and Load & Go™ XL Dispenser - Chrome Shadow. Model: WFW6620HC. SKU: 6313774. Paid over $1,000.00 for it. FIRST TIME washing our sheets, we had snags & rips. I immediately called and was referred to Whirlpool and then referred to an outside repair company. They sent a technician out who said everything was functioning properly despite having ruined 3 sets of sheets (these were not all washed at the same time & I didn’t realize they were being snagged until making the beds).I continued to use the washer - clothes were fine, but yet again, MORE sheets and now comforters RUINED!!!! I called YET AGAIN after troubleshooting the problem myself and finding that the drain holes in the drum had metal pieces sticking up causing the items to snag & rip. Another day taken off work to stay home for the repair. The repair guy comes out, the part was broken. So now I’m left once again with a faulty washing machine AND no ETA on when the new part will arrive and be installed AND having to take yet another day off work.7 sheet sets, 3 comforters, multiple shirts, & multiple bathing suits RUINED & was told there was ‘nothing they could do!’ I will NEVER EVER AGAIN purchase anything with the Whirlpool logo. It’s JUNK! Just an FYI, this was initiated in May of 2019 and it is now the middle of September 2019 with no fix updates. Who can go months without doing laundry???? Once again, poor customer service and JUNK of a product!

On 12/31/2009, I purchased a Whirlpool Cabrio, model# WTW6800WW1. I was excited as we have never spent that kind of money on a washer. We felt as though we had purchased a higher end washer and would have it for years to come. Wrong! About one year in to its use, I began to think it was getting louder during the spin cycles. I thought I was just being critical and it was just my sensitive ears. Now just past the two-year mark, I know it was not me. It’s the POS washer. It is so incredibly loud, not that you cannot be in the same room as it is during the washing time especially the spin cycle. In its defense, my clothes got cleaned.However, I know that the bearing is eventually going to give out and I will have a mandatory repair on my hands or have to pay someone to fix it. Either way, it’s a lot of time and a lot of money to fix a two-year old washer that should not need to be fixed. I attempted at getting Whirlpool to stand behind their product. No chance, no way. Good luck with that. Their washers last about 2-3 years. I will never purchase another Whirlpool product. This is a horrible product which is matched by their horrible customer service.

We purchased a Whirlpool refrigerator because of the brand in August of 2011. Its December 2012, the entire door needs to be replaced. It appears the cost will be as much as the original $750 investment! We called Whirlpool expecting they would stand behind their brand after hardly 18 months, but no ... It is clearly a defective door to begin with.

Cabrio washer - What a piece of junk! My washer is 2 years old, it now does its own thing - stopping when it wants, doesnt finish cycle, beeps finished and the clothes are so wet and the washer is not emptied. Then, I put it on drain and spin. One time, it kept going for almost an hour of off and on. My clothes were so out of shape and that was on low spin. I finally took them out and put them outside. The clothes from day one have always come out so wrinkled and that too is on low spin. Im afraid to use high spin. I know you have to for towels, but it still does not drain. It shuts off and on when it feels like it. My first contact with Whirlpool was, Well, did you buy the extended warranty? I hate it when asked that when purchasing any product. Its like saying, This is a piece of crap. Im warning you now so buy the extended. So right there, I felt Whirlpool isnt willing to help. What else can we all do here? Please advise.

The self cleaning work very well. All you need is clean the filter every time you use the dryer. I had the large capacity. I can wash my blankets and heavy clothes like commercial machine and the machine is programmable for your wash load.

I should have read reviews prior to purchasing the Washer and Dryer. The washer sucks big time. Does not clean clothes. Leaves soap in clothes. The repair man said use 2 tbsps. of soap. Still soap in clothes. I use 1 tablespoon of HE soap. 2 1/2 hours for 1 load because I have to use deep water and extra rinse on first wash. Then I wash again with no soap. I HATE this washer. Whites are now yellow after washing. Cannot do lightweight comforters. I am at the laundry mat more than using my new washing machine. Dryer is ok but does not remove any lint from clothes or towels. I always trusted Whirlpool. Not anymore.

Whirlpool Cabrio WTW8500DC0 - 2 months out of warranty, 14 months old. Motherboard fried. $300 if I do it myself. $550 to have it done. The unit was $780 on sale. Brand new piece of junk. Zero stars but thats not an option. Quite honestly, it doesnt clean very well and it doesnt rinse very well so we have to rinse twice to get the smell out if we use bleach. So whats the sense in buying a high efficiency washer? I work outdoors and weve had cheap washers in the past that clean much better and lasted many years.

Updated on 07/30/2021: On 5/4/21 a tree took out a neutral on the power line to my home and after inspection by my electrician, he said my Whirlpool refrigerator was done. Not even 1 year old. When attempting to get Whirlpool to replace the refrigerator, they said they have to try and repair it before considering any other options. As they do not cover damage by acts of God their warranty would not cover replacement. Mind you I paid around $1500 for my refrigerator and it was not even 1 year old. 5/17/21 (2 weeks from when the refrig got fried and I had to get and I had to purchase a used refrig until then) serviceman said he had to order parts. 6/1/21 - Motor-Cond $158.20, Fan Blade $13.97, CNTRL Elec $60 CORE [PI] $497.45 and Evap Fan Motor $183.91. Did not fix the problem and had to order more parts. 6/8/21 - Evap Fan Motor $183.91 (first one did not work), Rail $34.76. Service tech said to wait a bit before moving the frig back to make sure it was cooling properly. Finally moved it back on 7/7/21 and hooked up the water line. Few days later noticed water leaking from the top of the freezer door and a lot of water on my floor. Heard a funny sound and found water spurting from the top 2 corners of the freezer door. Called whirlpool warranty and was told they would contact me. Next I get a notice that I have a service appointment in August. Was able to get it moved with a follow up appointment with a part that was broken during the last repair for 7/28/21.7/28/21 - Fill tube heater for icemaker was open and frozen - now tech ordered Rail $34.76, Freezer Door $1,525.84 and Valve $124.23. 6-8 weeks custom order. So we also have to added 5 service calls to the cost - Approx. $500++. Total Replacement Parts = $2,758.81 with a final total cost to repair of $3258.81+ vs just replacing or reimbursing me for the appliance of approximately $1800. Someone needs to review their model because not only am I without a working refrig for 4-5 months, but the repairs cost them $1500 more and now they have a customer who will not longer invest in Whirlpool appliances because of bad business practices and inconvenience.Original: I purchased a Whirlpool side by side refrigerator in July 2020. Earlier this month I had a tree pull down a power line and disconnect the neutral, allowing a full surge of power to go through my house. It fried the exhaust hood, literally melting the components. It also fried my refrigerator. The electrician who reconnected my home signed an affidavit that the refrigerator was permanently damaged due to the surge. When contacting Whirlpool to file a claim, I was on hold over an hour before getting a person. This happens every time you attempt to contact them, so patience is required. I was not able to get a service call on my refrigerator for 2 weeks (5/17/21) so that left me without a refrigerator. The service company showed up early and I had no choice but to leave my job or reschedule another 2 weeks out. The tech said he could only repair and made an attempt to contact Whirlpool to get the unit replaced and he was on hold for over 30 minutes. They declined and said because it was an act of God they could not replace it. I was already having issues with the unit before the surge of a constant defrost that was causing food to spoil due to melting then refreezing causing freezer burn. I also lost over $500 worth of food. They dont cover. It also caused the icemaker to constantly freeze up. Now it will take at least another 2 weeks for the replacement part to fix and a refrigerator is not something you can go without that long. I had a concern this would happen. When speaking with customer I service, they said they just needed the tech to confirm it was damaged to replace it. At this point he said he does not know if the piece (on 2 weeks backorder) will fix it. They can only tell after the fact. He said Whirlpool only fixes and does not replace, which is not what Home Depot informed me when inquiring into the warranty with Whirlpool. They said Power Surges are covered. So with this in mind, I would seriously consider buying from Whirlpool. Things break, situations happen and no one should have to go without a refrigerator for over a month because they may be able to fix it. Then there is the concern if something is melted/destroyed inside, if it could cause a fire in the future. Will never buy another Whirlpool appliance again. They cant stand behind their products, the products are worthless. And yes, I am very upset. Again - just had Whirlpool tell me its not covered as it is an act of God! ARGH -

I have the Whirlpool washing machine for last 15 years and there has not been any complaint since its acquisition. I do a lot of laundry because I have a big family, but not major issue so far. I will recommend this brand to anyone willing to buy a washing machine.

Purchased a GGE388LXS04 electric range in June of 2013 from Lowes. In September 2013 one of the top burners went out, under warranty Whirlpool repaired the burner. Now after attempting to use the self cleaning mode for the oven, the ovens (top and bottom) along with warmer device do not work at all. This issue is evidently a major issue with Whirlpools electric ovens. Will call Whirlpool tomorrow as the oven is still under warranty, will also call Lowes and see if they will replace the oven with an oven with a comparable brand. Wish I had read this site before we purchased this oven. A very bad experience.

After careful research, I purchased a Whirlpool microwave 2 years ago. Model WMH2175XVT-2. It looks brand new. Three months after the extended warranty expired, my microwave wont heat anything. Ive tried all the suggested troubleshooting in the manual. When I called Whirlpool (the number right inside the microwave door) I get a recording that asks me if it has been more than a year since my purchase. I can only say yes because even the extended warranty with Sears had expired by three months. Then Im directed by the auto-operator to schedule a repair service. Im fuming and seeing dollar signs and no human to talk to, so I hung up. I googled my problem and was asked to pay $50 by an online repairman, so I clicked out of that window not wanting to sink more money into a bad purchase. Then I found a website from a consumer saying the Whirlpool Company admitted it was a bad magnetron with this model and that they have had a lot of problems. They should have recalled this microwave model or offered to repair or replace it for free. I have just decided that I will no longer purchase Whirlpool products. As soon as my oven and dishwasher die I think Im going back to Kenmore products.

I purchased a brand new Whirlpool Cabrio washer and dryer set not even 2 years prior. When I first started using it, I pulled shirts out of the wash after being ran through and found deodorant marks still on the inside of the shirts. I had to wash all of my loads on heavy soil and still had to run some loads through more than once. The wash machine quit working about 1 month ago, so I had a service man out to look at it. It ended up being the control panel and the part itself was going to cost me $300 and by the time I paid to have it repaired, the total cost was just under $400. The service man proceeded to tell me that Whirlpool had another company actually make the control panels for the Cabrio model and he has serviced several of these washers and when he would repair one part, another part would stop working. I was very upset and bought a new wash machine. I would like to add, I am a single mom with a 2 1/2 year old, so the wash machine was not used excessively in any way. I dont work outside so my clothes are never soiled heavily. Needless to say, my washer was not under warranty so Whirlpool couldnt do anything for me. A wash machine should last longer than less than 2 years. I would not recommend this model to anyone. And for Whirlpool to put their name on such a poor product is very disappointing since I have had good experiences with their products in the past.

Whirlpool built in oven. This piece of junk quit operating 6 months after purchase a brand new oven. I have called numerous times only to be treated like ** on you guys shoes. My next move is court. I didnt pay 1150.00 for nothing. I purchased a then what I thought to be a best buy. Very very disappointed.

I purchased a Whirlpool washing machine from PC Richards in Lake Grove 15 months ago. I paid $590.00. I had to call PC Richards back because it sounded like the machine was not spinning right. The servicemen came back and said nothing was wrong. It was supposed to sound like that. Now the machine stopped draining and spinning. I went to the store and they handed me customer service numbers and said they could not help me. I contacted Whirlpool online and received a phone call from a woman that gave me a lesson on how to load the machine and put soap in it! She was a very polite woman, but, gee, that didn’t solve my problem.After 4 days I was able to get through by phone and was told to call service. I contacted Mahler Appliance. He looked at it and said he couldn’t fix it and took a check for $81.47. He told me to call Whirlpool. I called Whirlpool again and got their service people. The gentleman came and could not figure out what was wrong. He tried a few things and said it was probably the main board. He said to call Whirlpool, but they most likely won’t give me back my money. He could charge me $460.00 for a new board per his supervisor. I just paid $590.00 for the machine and another $87.00 to some guy who took advantage. He left with an $87.00 check and I still have a broken washer. He did tighten up a loose wire he said he found and told me to try it and good luck. So I tried it. I put clothes in and turned it on.I came back about 20 minutes later to see if it continued to run and I slipped and fell on the ceramic floor because water drained out from somewhere and went all over my floor. I have injured my back and elbow from hitting the hard floor. I also have water all over the place and finally a very broken defective washer. I am angry. I hurt myself and have spent close to $1000.00 and I still have no working washer and no way to buy another one. The washer is 15 months old. That’s brand new to me. There was obviously a problem from the beginning. Whirlpool has always had a quality name for years. I would hope that they would stand by their product and fix my washer for me. It is obviously defective.

Four months after purchasing an $1,800 stainless French door fridge it began to not cool even though it was running. I called and was on hold for 45 minutes, then transferred to a different service company that could only come 3 days later. They were here a total of 3 times and each time they could not fix it. It would run for a few days or weeks then die again. Each time I lost a few hundred dollars in food. Each time I was on the phone for almost an hour, and each time it was days later before they would come. Whirlpool refused to refund or swap out the unit. I would have been stuck if it were not for Home Depot finally agreeing to exchange it for an LG.I have never been so upset with any companies customer service in my 45 yrs. The only reason that I am writing this is because my Sony 65 TV died the other day. It was 6 months old and I called Sony. They answered within four minutes and quickly decided to exchange it for a new one and extend my warranty for 2 additional years. There are still decent companies out there. I will never buy another Whirlpool product again.

We bought a Whirlpool dishwasher and microwave from a reputable appliance store. The dishwasher top basket broke within 30 days. The microwave lost 100% power within 30 days. Both under warranty but parts had to be ordered. Couldnt use either appliance for over a month. What is going on Whirlpool? We need a refrigerator, but I no longer trust your brand. I dont want it to quit and then lose all of our food! Please get it together and make quality products again.

I just purchased a top load wtw5000dw01. There have not been any changes to this revised model except the lid only locks in the rinse/spin cycle now. If that even helps anybody. It still has the noisy agitator which is the thing I hate most. Whirlpool engineers better go back to the drawing board and redesign their washers. Whats this country come to when you spend a pile of money on something that sounds like it is broken from brand new. I also had a washer that was 15 years old and never had noise issues or problems with it. Its just not Whirlpool that uses this so called new technology.

My washer is a top load, energy and water efficient model. I am amazed at how little water it uses and how well it cleans. I do have two issues, the capacity looks huge but it will not take a queen size and double sheet set in the same load. It unbalances and then cant seem to get going again. The other issue is that you cant pause the wash and adjust things, you have to cancel and start over.

Model WTW7600XOW, installed 12/9/2010. For about 4 months this washer has sounded like a jet plane when spinning. I called Whirlpool to see if it was recalled or what they recommended. They provided 2 repair places near me. The repair shops recommended buying a new washer since the repair is so costly. A 4 year old washer used by 2 people should have bearings that last more than 4 years.

I bought refrigerator in Feb 2017. Within 18 months internal surface got crack, contacted customer care but I would say Whirlpool India customer care department is worst across world, no courtesy towards customers, contacted them over phone very bad attitude, no response on email. Product quality is worst, its better to buy Indian brands. They are much better in quality & service. Totally dissatisfied with Whirlpool approach, at the end Whirlpool customer care is not at all bothered.

Cabrio Washer - I am so disgusted with this product. After only a few months service came out and the repairman told me it was normal for a load to run for 8+ hours. Second repairman replaced the circuit boards and it has lasted 11 weeks. Now it is not working again. Calling tomorrow. I have a bad feeling about what the end result will be. Expect I will be buying a new washer, will not be a Whirlpool. Just went and tried what another reviewer does to get it to run... Pause/start/pause/start. After 8 tries it is now running. I will not live with this. Not going to spend a dime to fix this piece of garbage. Still have 36 days left on extended warranty.

Whirlpool Duet washing machine model WFW9500TW03 - Just after the first year of owning this machine, the metal hinge to the door cracked and the door didnt shut properly. It was replaced. After a couple of years, the bearings and drum of this machine failed. The cost for parts and repair were as much as the machine new. After repairs, the machine never ran quietly again. I have called for repair a second time for the same issue and he has confirmed that its the bearings again causing the drum to dislocate and hence, break the belt that I now need to replace. My problem is with Whirlpool for its defective metal in its machines (many complaints on the internet will confirm this). I believe there are enough consumers out there to file a class action lawsuit.

We have had our dishwasher for over ten years and have had no problems. Its been very reliable. Its a free standing unit on wheels with a butcher block top as we dont have room in the cabinets for a built in. All you have to do is roll it over to the sink and plug it in and hook up the water line which has a quick disconnect. The male half always stays on the faucet.

Ive never considered writing a complaint before, but feel it is necessary in this situation. I have had my Whirlpool refrigerator since November, 2007. It has worked great until this past April when the freezer began to overfreeze, cause frost and ice to build up. I have had Whirlpool Factory Service out to repair the unit twice a month since April with still no resolution and the appointments are getting harder and harder to get someone to come out in a timely fashion. I called on September 1st and the closet appointment is September 15th. They werent even able to book the appointment when I called. I was told someone would call back within 3/4 days. When I didnt hear back today, I called to find out an appointment was set.Ive called the Resolution Team to obtain back records of service but havent been successful in receiving a phone call or email. I havent received all of the follow up emails after service which is frustrating since there have been two technicians that have come out for repair and were not provided any history on the unit. If I had the follow up emails, I would be able to share that information with them.I contacted Customer Service to find out what I can do in regards to the issue I am having and was told its best to stay with the service provider that I began with since they are familiar with the issue. I would imagine if they are familiar with the issue that it should have been fixed by now. Ive also sent a response card back to Whirlpool Home Appliances at the Survey Response Center and havent heard anything from them either. When I called to follow up there wasnt anyone that could point me in the right direction to obtain answers. They were able to provide me with the mailing address for Consumer Affairs though. Ive been told numerous times that if it gets to a point it costs too much to fix they will replace the unit. Im not sure when that decision is made. I have an extended contract and will extend it again in October when it expires. I just want the unit fixed or replaced. Its been since April with the same issue. Very disappointed consumer.

Our Whirlpool dryer broke less than 3 months after we bought it. We called Whirlpool and spent more than 2 hours on the phone. They sent someone out and that person told us he couldnt fix the part that was broken. He gave us a phone number to call and we called and spent another hour on the phone after which we were told to call Whirlpool back. We called them on 3 separate days and spent hours on the phone trying to contact real people. After another week (during which time the dryer went out of warranty) we had to call someone to fix it. After that we spend a month calling and emailing Whirlpool to get reimbursed for the almost $400 we spent fixing it. No luck. We were told that it was out of warranty and we didnt use a Whirlpool technician. I was hung up on, given the runaround through phone menus, continually told it wasnt the correct department, and finally that Whirlpool doesnt cover it. Bottom line is...never buy Whirlpool.

I have previously owned a Maytag washer for 16 years that went through three children. They are older now and two years ago I decided to buy a Whirlpool Cabrio for the upgrade and large capacity. Well just like every other customer that purchased these crappy machine, I now own one of the worst washers in the history of washing machines. It started about 13 months after I bought it and now is completely broken. I am so angry that I spent the amount of money I did to be so disappointed. I have not abused this washer and I can hardly believe the customer service or lack there of, that this company supports. I would hope that people do their research before ever purchasing a whirlpool anything. TERRIBLE COMPANY and my Cabrio is heading to the landfill.... Thanks Whirlpool. YOU SUCK!

We bought a Whirlpool refrigerator in January at Home Depot. In July we started noticing that the freezer doesnt work. The ice maker doesnt work, everything melt away. Frozen items were lost. We constantly have to dry the floor since it is leaking water. We called whirlpool on July 27 and they send someone to check it out the following day. He reported that we need a new freezer door. I call for a follow up, I was told that it will take 6-8 weeks before we get a new door and part for the ice maker. We recently called to follow up on the status of the door just to find out that the order didnt get process until mid August. In the meanwhile, the fridge is having condensation. Water is everywhere inside. Fruits are being rotten because of too much moisture. We called again and they send out the same technician. The technician reported that the fridge will not work properly until freezer is fix. We call whirlpool again just for them to tell us to wait for the part, and gave us an extra 6 month warranty.

We moved to a new house Nov. of 2012 and I went to Lowes to buy a new refrigerator. The last refrigerator we bought was a Maytag. It was a LEMON and probably had every part replaced because we had the warranty. At Lowes I thought the Whirlpool Refrigerator would be a good choice. We didnt purchase the warranty, big mistake. After only 4 YEARS, the refrigerator is DEAD, not in working order and would too expensive to fix says our reliable repair serviceman.

Refrigerator stopped cooling... Paid $200 to have it diagnosed... Cost more than a new refrigerator to get fixed...$14,000. Refrigerator was 7 years old, energy star. How can it be energy efficient if it was made to last only seven years? How much energy is wasted making new ones to replace the broken ones, that cost too much to fix. Energy star. What a scam.

I bought a Whirlpool Cabrio Top Load washing machine September of 2012. It has never cleaned the clothes well. For the last month the machine has a very loud spin cycle. I am very unhappy with this purchase and it is 2 months out of warranty. I emailed WHIRLPOOL and was told that all appliances have problems and wear out. WOW! It is 14 months old and has been used with care. I will never buy another Whirlpool product.

Just bought this washer, its making a lot of noise, sounds like something is grinding (metal, gears, etc). I thought Whirlpool was suppose to be good. I just had my Maytag go out after 18 years of service, thought about getting another Maytag but found out Whirlpool makes those. As many complaint as I see, seems there needs to be a class action lawsuit against Whirlpool for shoddy work.

I bought a new Whirlpool refrigerator at Home Depot for about $700. Six months later, suddenly, it starts making an intermittent but constant loud grinding noise and then the squeaking started. I called Home Depot first because I bought the protection plan. They referred me to Whirlpool who said the protection plan doesn’t kick in until another year after the warranty ends. It makes these noises whenever it runs, which seems to be more often (that it is running). Whirlpool may still charge $120 just for someone to come look at it even though it is under warranty. I asked another repair place and they said it might void my warranty for them to look at it instead. Whirlpool said it wouldn’t void the warranty but they would only work on it after the first repair person was finished. I’m waiting for the repair guy to come and see why it is making these loud noises. Another person with more knowledge of fridges than I have listened to the noises and said it sounds like friction in a motor. I read a review of the fridge that said the reviewer had problems after only 6 months and I thought that must be a fluke. Apparently not.

Purchased a Whirlpool hot water tank from Lowes 5/12 and have had NOTHING but problems with it since day 2. The tank I replaced was around 20 years old, never a drip, never a problem, it just finally rusted through.. Well this piece of JUNK I had installed is just that JUNK.. I have been in contact with this company many times, they ALWAYS have a new story. I replaced my old thermal expansion tank 3 months after buying this JUNK because I was told it could be that. Well that didnt fix anything and cost me $60.00, then it was pressure relief valve, ok, another $20.00, nope not that. Well back on the phone and emailing this company, now they tell me I am not vented correctly, because with all the repairs being done on this tank, my Son noticed the top plastic pieces melting. Well back on the phone I go, and of course Whirlpool tells me, its me again.. Had piles going into my chimney replaced, no help, replaced thermal expansion tank again, no help, replaced pressure relief valve, no help. So sick of cleaning up water I want to throw up. Well I now know why they say, do not return to store where you purchased it, because it is bad business to have Lowes parking lot, looking like a Whirlpool graveyard for their product. .

I purchased my washer about 1 month ago and I used daily. I went away for the weekend, and now it does not work. Washer will not wash, fill or spin, gives a LF error. All lines have been checked. I need to call service.

My agitator-free washer began tearing small holes in my clothing and sheets about one year after purchase. I contacted Whirlpool and they sent out a service person, who ran a diagnostic test on the washer and said it was fine and I should learn how to wash clothes and load the washer, etc. The barrel of this washer has little holes and I believe that when it spins the clothing, some pieces may stick in one of those holes causing tearing. The service person also told me that my clothes were old. I guess that means this washer is not for washing old clothing. The tears in my clothing are in places that are very unlikely to tear, like the back of my jeans behind the calf of a leg, about half way up from the ankle. There are holes in my tee shirts at the bottom of the back. Even if I were a smoker, which I am not, I would not likely burn holes in those areas. Whirlpool obviously does not want to accept responsibility for this problem, even though there are many other people having the same problem with this type of washer.

I earlier filed a complaint about the Whirlpool Gold microwave arcing within a minute of cooking frozen green beans and causing burn holes in the food. We contacted Whirlpool’s customer service and were told that the machine was no longer under warranty, but we could have it serviced, repaired and have an additional year of warranty for $259. We took a pass on that. Further trial and error along with research helped us come to the realization that the arcing was caused by the high mineral content of the green beans. Whirlpool did not tell us this, but we found the information provided by others. We no longer cook the particular brand of green beans which seem to cause this event. The microwave is no longer arcing. You would think Whirlpool might be aware of this.

We purchased a Whirlpool Cabrio washer and dryer set in 2013. In 11 months we have made at least 6 calls concerning the same issues machine leaving white residue on clothes. It has been one thing after another. Today the manager told me that my warranty only covered parts and not a replacement machine. I am washing my clothes two or three times to get them so we can wear them. First this is not saving water, energy, time and most of all CLOTHES. We are wearing our clothes out washing them. This is unacceptable. With this many complaints, the company has to know they have a machine with issues. I will never purchase Whirlpool again. I think we should all band together and file an action against Whirlpool. These machine cost too much money to be crappy.

I am the owner of a 4-year-old stainless steel Whirlpool refrigerator, Model GB9SHDXPS02. Yesterday morning, my 5-year-old daughter opened the fridge door to get a snack. The door came crashing down, hit the floor - missing my 21-month-old daughter by less than two feet - the drawer smashed off on impact and flew across the kitchen floor and the contents of the drawer (salad dressings, syrup, condiments, etc) went flying too. Miraculously, no one was hurt. My children were obviously upset and crying, and I was shaken. My laminate floor has a large dent and long scratch from the impact.My fridge door is broken. I cannot get through to Whirlpool Canadas corporate office to speak to anyone. The Whirlpool Canada call center is giving me the runaround. Yesterday I spoke to a supervisor at the call center who advised me that someone from the Corporate Safety Division would phone me within 24 hours - but I have not received a phone call and it has been more than 24 hours. I am noticing a complete disconnect between the gravity of the situation and an appropriate response from Whirlpool. I am a mother of 4 small children - two of which were very nearly killed/badly injured by a faulty refrigerator door. I cant even get a phone call in response. This is a serious safety issue. Im tired of apologies, some real action needs to be taken to ensure this never happens again to any consumer.

I purchased a new water heater in August 2013. The pilot light started going out in October/November of 2013. After calling the Tech Support phone number, (877) 817-6750, I was advised to clean the burner screen. First this is very difficult to do because the burner screen is underneath the water heater and almost impossible to access. Second the closet the water heater is in did not show any signs of debris that could clog the burner screen. I did as they recommended. Several calls, and several weeks later, they finally authorized a technician to come and service water heater. He performed a cleaning even though he couldnt find anything to clean; and he replaced the control module. The new control module worked through the spring and summer seasons and then I started having issues again in the fall, late October. Started calling the same phone number and was told again to clean the burner screen. I convinced them to send out the technician again. The A and E Factory technician came out and only cleaned the burner screen and left before I had a chance to get home. This happened several times and I called Whirlpool every time. The next A and E technician told me to try changing out the draft vent chimney to a different size, which I did. Problem happened Again! I finally asked for another plumber and they sent me 3 names of their authorized plumbers. I called Phil, Philco Plumbing. He told me that I needed to have more ventilation, so I added more ventilation, even though I later found documentation stating I already had more than what was required by the manufacturer. Again, a week later, started having problems. Call back and asked to have my personal plumber come out. This time the rep told me that I have always been free to choose any plumber I wish (why wasnt I given that option the first 10 times I called?). My plumber came out and replaced the control module and the thermocouple, but wasnt convinced that these were faulty parts, he honestly couldnt figure out why I am having this problem, but it was worth a try. That lasted about 1 week and now I am having the problem again!!Whirlpool will FINALLY authorize a new water heater, but they will not authorize installation for the new water heater. I have already spent money on recommended repairs that have not worked. I have taken 15+ hours off of work to watch plumbers do nothing that has rectified my problems. And now Whirlpool wants me to deal with installing the unit myself, OR pay to have it installed! They say they wont cover installation because I purchased it more than 1 year ago. They seem to be missing the fact that I have had trouble with it the ENTIRE time I have owned it!This Flame lock system is garbage. I found on Consumer Affairs that a few years ago a class-action lawsuit settled, dealing with the same issues. I think it is time for another round! I KNOW that I am not the only one dealing with this problem because the plumbers I had out all had similar complaints from many of their clients. Whirlpool wont fess up to the problem, but the problem is real.

I purchased a 50-Gallon Electric Water heater in 2006, sure it lasted and worked well for quite a few years; however, in August 2014 my power bill started to rise dramatically, I live in Arizona and $300-$400 power bills are the norm in the summer months; however, a $700.00 bill will immediately be noticed. I contacted the power company and they sent a tech over who performed a lengthy diagnostic and determined that my water heater was running constantly thus accounting for the great increase in power, I contacted Whirlpool and received 2 heating elements (no charge) which my pricey plumber replaced.The problem still remained and I contacted Whirlpool again and again trying to get this issue resolved. I paid less than $400.00 for the heater installed and since Ive been having the issue Ive almost paid another $400.00 in labor costs trying to get a resolution. Ive decided to get another system and my only reason for posting this is to inform all that the Whirlpool heaters seem to be very problematic, like others Ive had plumbers decline my business when I inform them that I have a Whirlpool tank with the Energy Smart module.

We purchase all Whirlpool appliances for our new house in Florida in late 2015 from Good Deals Appliances. First repair before 1 wk in-house was the dishwasher. Wires were not connected. Now it is the refrigerator (French door refrigerator model K44913210). We reached out where we purchase the appliances and they gave a number of repairman to connect. He came and told us the compressor & evaporator & valve needed replacement, We found that hard to believe that a 2-yr-old refrigerator needed all this repair. Called another repairman to hear same thing. We were also told this problem is so common with this model. Called Whirlpool. They sent a repairman out. Said same thing first two said. They are paying for parts but not labor. We were told by last repairman that this refrigerator hasnt worked from day one. Passed info to Whirlpool and no comment. We paid a lot of money for an upgraded refrigerator to have it quit in 2 years. Totally not acceptable. On top of this the parts may not work for more than 2 years again. Okay Whirlpool who is going to pay for all the ice & dry ice, the other two repairmen that came. The repairman you sent was double the price of other 2 & will not come back till we pay. We will pass our experience with Whirlpool on to all friends and friends of friends.

Purchased I assumed a brand-new electric hot water heater from Lowes. It worked giving us hot water for 5 months then it quit. We called the number they have located on the side of the water heater and they sent 3 references such as plumbers for us to contact because everything they told us to purchase didnt work... so after their references, plumber came out. Instead of him telling us what was wrong why all of a sudden we stopped getting hot water he didnt return our phone call. As a professional that sucks!!! So WHIRLPOOL CUSTOMER SERVICE says the hot water heater that had been working for 5 months wasnt up to code and wasnt wired right and WE need to pay an electrician to connect it right... thats **. The electrician did it correct the first time. Whirlpool just dont want to accept the fact that their equipment is faulty!!! But thats good because I will NEVER purchase anything WHIRLPOOL makes. I dont care if they start making water. I will just quit The hell with that company!!! WHIRLPOOL SUCKS!!! Heres the serial number 1626103174130 and if I had read the neg reviews before I purchased the hot water heater I wouldnt not have done it!!!

I was under the impression Whirlpool washers were good. Mine always goes off balance and quits. I carefully redistribute the load several times to get it to finish (start over). Sometimes it works fine from the get-go, but not often enough. It is now 2 years old and if I were wealthy, Id shove it to the curb. There is little to like with an appliance that often must be adjusted and re-started. I will try Samsung next. It seems that American brands are not reliable. I have no special needs and will consider reliability above all. The name Whirlpool would be a deal breaker for me. I cannot abide my Whirlpool washing machine as it is more of an aggravation than something useful. Stay away from Whirlpool washing machines. They (at least mine) require the load to be balanced to a microgram. Appliances should just work and not require fiddling with.

I purchased a fridge from them a little over a year ago. First and LAST EVER. The freezer door started to sag and when I called them I was told my warranty expired a month ago. Had a Whirlpool service person look at it and told me that the cost is $110 plus $45. I said that is fine. They scheduled another appointment but I received a call 12 minutes before the time expired (as you know they say in the afternoon and no exact time and they said between 2 and 4:30) and the guy asked me what is wrong with the fridge. I told him that someone took a look at it a week prior but I had to go through the whole thing. Then he said that they dont have the part and I have to wait for a week. This was a Saturday before Xmas and waited all afternoon to be told that was very upsetting. Any how I called customer service and spoke with a Michelle. She said she is going to try and find out if she can waive the additional service fee, arrange the time and will comp the parts (around $15). After 45 minutes on the phone I had to jump off for a business call so Michelle said she will email me and I gave her my email.Few hours passed and no email. When I called back the idiot that answered the phone kept saying that the warranty is out and I need to call another number so I asked for a supervisor. I was on hold for 11 minutes then I was hung up on. I called again and asked for a supervisor. Spoke with Benjamin (Opt# **), he said that Michelle notes did not state anything about help in possibly waiving anything and that I refused the parts. I was furious. What a LIE. Long story short he said they cant waive anything and I should call the scheduling number for any help. I asked to speak to Michelle and guess what the answer was... SHE IS BUSY. What the hell. The service is well below zero as well as the quality of the product. I am going to send a letter to the office of President (Jeff Fettig) Whirlpool Corp. 2000 North M-63, Benton Harbor, Michigan 49022-2692. It is so sad when corporation are so big that little people who buy their products dont mean much to them.

Whirlpool 70328 215 IMFRESH ROY 5S purchased on 14th Feb. 2016. It has stopped cooling on 11th April 2016. Complaint lodged on 12 April. No serviceman attended and not connecting toll-free number. Never, never go for a Whirlpool refrigerator.

My three month old $2,000 combination microwave-oven works a fine, its the just the details that stink. For example: There is no way to turn off the turntable. Yes! a crappy $40 microwave can do this, but not this one. Liquid got into the middle of the door window. You cant open it up to clean, they want to send a technician to clean that up so you can actually see through the window. How much? $150. How was it possible that Whirlpool did not adequately seal the glass? They dont care, and dont care about how it looks.

We were a Whirlpool family, and have been using a Whirlpool front loader – Duet Steam Model # WFW9500TW - for the past nine years without any issues until recently when it started to vibrate. Technician sent by Whirlpool blamed it on failing bearing and that it was cheaper to replace than to repair (In hindsight, I wish we had tried repairing). Naturally, we decided to replace with a new front loader from Whirlpool - Model # WFW6620HW. Our previous version had a max spin speed of 1000 RPM and a capacity of 3.5 cu. ft. This new one has a top spin speed of 1160 RPM and a capacity of 4.5 cu. ft. The main problem with our old one was vibration, and this was being caused by the washer going into high spin while the clothes were not evenly distributed throughout the drum. In one spin, the clothes would spin perfectly without any vibration, but in another spin of the same cycle, the washer would not allocate that same clothes properly throughout the drum, which leads the drum to cause vibration from unbalanced high spin. Vibration is a problem, because like most Americans, we live in a wood frame house, and have a basement underneath with the washer located on the main floor. Vibration from unbalanced high RPM spin gets sent down to other areas of the house, causing damage, drywall cracks, separation in trims, etc. And these are all only the damages one can see with their eyes.One point about vibration and some myth busting. Provided that all your washer legs are meeting the floor and not on a saggy floor, your washer should not vibrate more than it does during an empty spin. If it does, then it is due to faulty, poor design/engineering. What happens is when the steel drum becomes unbalanced with laundry in high spin, it starts to shake as more of the weight is on one side, which one can notice looking inside the washer window. There are concrete weights fastened to the top and bottom of drum to keep the drum in place and to reduce its shaking tendencies. However, this weight also causes the washer cabinet to wobble if the drum itself is shaking. This wobble in turn causes the washer legs, which may be firmly grasping the floor, to very slightly come off the floor, which one can feel if touching both the washer feet and floor with their finger at the high spin of an unbalanced spin. And that motion of legs coming off the floor and hitting back at high RPM is what causes vibration to be felt on the floor and to be seen on the cabinet. Of course, this effect is amplified with washers that decide to go into an unbalanced spin with an even higher max spin. When our old washer perfectly balanced the clothes, it behaved like it was running high spin while the drum was empty. This is how all washers should behave, especially in America where the vast majority of homes are wood frame based. However, that was not what we experienced with this new Whirlpool. If a washer is not capable of balancing out the clothes, extra function or feature should be deployed in containing the drum shake to within the drum, and not allow it to escape.First, our old front load Duet Steam Whirlpool was Made in Germany. This new one is ‘assembled’ in America. The door window of the new one is plastic and feels cheap and flimsy, but I expect all the darker color door windows of newer front loaders to be plastic. Consider it cost cutting. We did not look for additional anti-vibration technology because our old Duet didn’t have anti-vibration features aside from its two springs and four suspensions. We decided not to use Load & Go because I have personally seen liquid HE detergents gum up over time, so I didn’t want to risk it gumming up inside the washer.After the installers left, I spend an hour cleaning the outside of the washer to perfection. Sadly, time wasted. Once I was done, I first did a wash without clothes, and then with clothes in Normal, fast spin cycle with drum about 2/3rds full. Just pants and t-shirts. There is a recirculating pump at the top of the drum to distribute the water, and to also distribute soap mixed water. But I am not sure if this is without problems. These pumps can collect soap residue with time, and you will eventually end up rinsing the laundry with soap mixed water even in rinse cycle.In getting to the first spin in wash cycle, I was flabbergasted to see how, just how rudimentary, I want to reiterate the word rudimentary, the load detection was before entering high spin. Our nine-year-old washer had a more comprehensive one. The new washer would spin the clothes at very, very low spin and simply see if the drum is most evenly spinning. That’s all. Compared it to our old washer which would also shake the drum to see if there was movement from side to side, because clothes can change their position when entering high spin. This rudimentary load detection causes the new washer to create an even worse uneven load distribution around the drum before spin, even though it may seem even at very low RPM. So, why is the new washer’s load detection so basic? I believe it is due to ball bearings.Front load washer models from other companies employ ball bearings to reduce vibrations from uneven loads. Whirlpool does not employ such feature, at least, they do not advertise them. However, to my surprise, I hear metal balls hitting each other every time the drum direction changes during the wash cycle. I inquired Whirlpool about this and I received contradictory responses. My theory is that the basic load detection before spin speed is used because Whirlpool assumes any changes to load distribution will be taken care of or reduced by the ball bearings of the washer. But this ultimately allows the washer to go into more uneven spins. The bearings may also be used to increase the tolerance of what is considered an ‘unbalanced load’ in order to get the washer to go into spin cycle faster, decreasing the time involved of the washer to go into spin cycle. Sadly, to my dismay, the new washer ended up causing a worse vibration than our old one with failing bearing.I called up the retailer the same day of delivery and complained of vibration. He first sent an installer to see if it was installed properly, and upon showing the installer of the vibration issues, the retailer sent me a new washer couple of days later thinking the first one was a lemon, and even though it has less noisy draining noise, it too exhibited the same issues with it going into significantly uneven spin. In the end, we decided to return the Whirlpool washer all together, at a loss of $200 because the retailer did not hold up to their spoken return policy.We have done many loads in this washer to see if our loading is an issue, loads of varying sizes, loads of varying types, loads of weights, and we maybe only had an evenly distributed load around the drum about once or twice. Once it was a King comforter. But, like our old washer, this too ended up not distributing properly around the drum in the final spin cycle and started vibrating, even though it was vibration-free in the previous high spin cycle. This proves that the problem exists directly within the washer, not the floor, leveling, load, etc.Some other problems with the washer: - The washer door, Load & Go dispenser at bottom, and single load dispenser at top are all plastic parts which all vibrate significantly during fast spin cycle. Especially the Load & Go dispenser which keeps hitting the cabinet to make banging noise. - Drain sounds are much, much louder than our previous Duet. It was even louder in the first one we received. Combine this to uneven spins and this washer can perhaps compete with an engine in terms of the sound it generates. - Single use dispenser at top left will hit the washer door if washer door is opened when the dispenser is also in open position. - Buttons are sometimes unresponsive, to which I have to power off and try again. But this has only happened a couple of times.- There is a small ¼ in. opening where the steel drum meets the rubber gasket, opening in which items like coins, etc., may fall through and are irretrievable. Don’t think small socks would be affected.To potential buyers, I suggest you proceed with caution when it comes to this washer. Understand the retailer’s appliance return policy and make sure it is shown in paper. It can save you a lot of headache. Get the extended warranty of three years because manufacturers only give you one-year warranty for a reason. I would also suggest that you avoid this washer at all costs if you have any floor level below where this washer is to be installed, especially if the level below is a basement. Your house is more important and more valuable than a $1000 washer.In the end, I am very disappointed in Whirlpool, an American company. Perhaps Whirlpool focuses their attention on top loaders, not front loaders. But Whirlpool had nine years to improve their washers, and it is sad that we may now have to go outside of America for a quality product to be used in American homes. P.S. No solicitation please, Whirlpool. This washer is in the process of being returned. P.S.S. I already posted this review in Whirlpools website, and it is under moderation.

After reading many of the 1,500 +/- complaints about this inferior product, I guess I should consider myself lucky. Ours didnt fail until this past Saturday, March 22, 2014. We purchased this Whirlpool (American Water Heater Company) water heater FG1H4040T3NOV at Lowes, and had it professionally installed, in October 2004, and we have had no issues until this past Saturday when we woke up to no hot water. After checking for the obvious, and finding no apparent cause for the failure, I considered it a fluke and relighted the pilot. The pilot took a few attempts to light, but it lit, and the burners came on.Three days later, we woke to no hot water again. This time, we placed a service call to the company that did the initial install. The technician came out, and after his inspection he informed me that the thermocouple/burner assembly needed to be replaced. He also informed me that this is a well-known issue, and Whirlpool has been sending out free updated replacement parts. He called Whirlpool, only to be told that they are no longer offering free, updated parts. Whirlpool also cited that the water heater was out of warranty (by less than 5 months). He gave me Whirlpools number, so I could contact them myself.As I smelled a rat, I began to do some online research about this issue, and, to my chagrin, I found out that I was far from alone with this issue. As of this writing, 1,500+ consumer and professional complaints, a settled class-action lawsuit, etc., etc. I contacted Whirlpool, explained my situation to the support rep, and, he proceeded to tell me that he couldnt help me with free replacement parts, due to the warranty being expired (less than 5 months). I argued with him, stating that this is not a warranty issue, but is in-fact a design/manufacturing defect issue, that has resulted in a redesign/re-manufacture. I cited the myriad of online data and negative testimonials, and I reminded him about the settled class-action lawsuit on this very topic. He acknowledged all of the above, was unimpressed, and offered to sell me the parts.After 15 minutes of back and forth, I asked to be escalated to the next level. But, of course the supervisor was unavailable, and If Id care to leave my name and number... yeah, right. Bottom line, Im very angry! I paid good money to Lowes for Whirlpools product, with a nine-year warranty. I had it professionally installed, and we have no hot water due to poorly designed parts. And... I am being forced to purchase the redesigned parts. Its truly unsatisfying to be an American consumer these days!

On 9/28/16 I purchased 4 new Whirlpool appliances from Orvilles Appliances in Buffalo NY. They were delivered on 11/9/16, the refrigerator was installed. The microwave, dishwasher, and range were not installed until Jan. as my kitchen was being remodeled. Both doors were dented; it took 3 months for Whirlpool to send new doors. After installation water began pouring all over, gallons of it; it took a month to get fixed. The microwave door has a large defect and the surface light does not work; it is still not fixed. Six months later it is still it fixed. I feel like I paid a lot of money for defective appliances. Whirlpool is truly a company that does not stand behind their products; they could care less about their customers. I will never ever do business with Whirlpool again. And Orvilles also refused to help; it was a mistake to shop there.

I have a similar problem with my stainless steel Whirlpool bottom freezer refrigerator, model EB9FVHRWS01, purchased in May 2011 from Sears Canada. Exactly a year later, right after the warranty expired, I started getting ice forming on the floor under the bottom freezer. I have been cleaning it out on a weekly basis for the past just over a year. If I dont clean it out, then water seeps out onto the floor. I purchased an extended warranty for my new stove but didnt for my fridge.A co-worker had the exact same problem, with ice forming on the bottom freezer exactly a year later. He purchased the extended warranty and had the Sears repairman come in and replace a $50 part (box in back) ($150 labour). The repairman said this is a manufacturers defect in these fridges and theyve had many such cases. Apparently, the box in the back freezes up and water cant drain to where its supposed to go to be evaporated so it drips to the bottom of the freezer. I contacted Whirlpool and inquired, and they said there was no defect or noted problems with my model. Now Im contemplating whether or not I should spend the $200 and get the defective part replaced. Sigh.

I bought my Whirlpool gas stovetop in March of 2016. The burner knobs that connect to the stove is made of plastic and all 5 knobs broke within the first year. Each year I have replaced knobs and had issues with the knob breaking and then not being able to tell if the gas is off or on. I have called and talked to people at Whirlpool about this issue several times. Although they seemed concerned they will not replace the knobs and I have had to purchase them through Whirlpool. The gas stovetop obviously has a serious and extremely dangerous design flaw. I have kept some of the broken knobs just to tell others about this terrifying flaw. Again, last night the gas was on for several hours before we discovered it!! I called Whirlpool again and they were unconcerned. The Model is #WCG97US0DS00, Serial#D60509297. Beware and DO NOT PURCHASE this gas stovetop. I wish I had not bought mine.

My Gold Series Whirlpool Electric Range is 3 years old. The main board for driving the burners, oven, etc burned up which caused my oven to go from the 200 degree setting to 450 in about 3 minutes burning everything that was in the oven. They want $400.00 + installation to replace it and that is if one can be found to actually install. The stove was purchased for $850.00 because of the Brand and now they want half that value to replace a board that will likely fry again in a year or two. I find there is no value for money and will not ever buy a Whirlpool brand again.

My Whirlpool refrigerator, model number ET8MHJKXM005, constantly leaks water into the bottom inside of the refrigerator. Its only 4 years old, for crying out loud! I have a repairman coming over in a few days who tells me the newer Whirlpool refrigerators are notorious for having the drain ice up. Why would Whirlpool design such garbage? They should all be recalled.

After 1 1/2 years, My new Cabrio washer lid hinge started to come apart and wont latch, so machine wont run. After a day or so it completely popped up and out of align. The lid has PLASTIC hinge. This is obviously a problem. We have been in touch with Whirlpool, but they say they cant help?? This should be a recall. We have been waiting on back order for a replacement Lid at OUR OWN EXPENSE since Sept. 20, 2015. I want to get this fixed and use my Machine again. We are Senior Citizens and this machine is used 3-4 times a week. Not abused.

54 weeks ago, I purchased a Whirlpool Duet Washer & Dryer. The first time I used the washer, it flooded my laundry room. After some grief, it was replaced with a second Duet washer some 53.5 weeks ago. Yesterday, that washer, 10 days past the 1-year warranty, failed. It gives error messages F06/E01 and wont complete a cycle. Calls to Whirlpool resulted in a refusal to acknowledge any product responsibility (out of warranty) but offers of extending the warranty for the cost of repair. I will never buy another Whirlpool product and will actively encourage any other consumer to shop elsewhere.

Sounding like a broken record, this washer is such a disappointment! I had high hopes for this top loader and thought I did enough research. Bought a Cabrio in Oct 2016 and have never liked it. They will have you believe it’s your fault... the wrinkly clothes, the clothes not clean enough, the white marks over all your clothes... you can’t change your detergent or softener enough and change the amount enough... it will still be there. So disappointed??? Want my front loader back!

Bought this washer 3 months ago. Absolutely hate it! Leaves white film on my clothes. Have to run all washes through a quick wash to get the film off. Hammers the water through the pipes, causing the fittings to come lose and leak! The spin cycle practically dries the clothes leaving them so wrinkled that I have to dry them longer to get the wrinkles out. Waste of my time and MONEY!

I purchased their washer, dryer, refrigerator, freezer, oven, and dishwasher. All were brand new when my home was built in 2006. Whirpool is the absolute worst home appliance company in both customer service and product. I would save my money and purchase any product other than a Whirlpool or Maytag. All of my appliances are a little over 5 years old and all have had multiple problems. Corporate takes the attitude of oh well, pay for the multiple repairs or buy new after 5 years or less. Ive never heard of disposable appliances, but Whirlpool has a full line of them! I would rate them less than 1 and just plain **!

We purchased KitchenAid Model YKESS907SS05 Electric Range from Appliance Canada April 2012, just before we took possession of our new home. We began using the range in July of that year and it worked well until September 11, 2014. At that time we decided to use one of the features of the range which is the self-clean feature. During which the control panel failed and our oven ceased to work.We contacted Appliance Canada and they suggested a technician come to assess. We called the suggested number and they send a technician that was not Whirlpool certified and we had to pay out of pocket for the visit $158. He did absolutely nothing during the visit. We then called Whirlpool Canada and they informed us that he was not Whirlpool certified and to call Appliance Canada, we immediately called Appliance Canada and made arrangements to have certified technician come to assess. Whirlpool Canada also indicated at that time that the board that failed was still under warranty and we should not have to pay. September 22nd the second technician came to assess the situation, used tape to cover the front blowing air duct so as not to have the hot air blow back onto the control panel. This was a temporary fix, they ordered a control panel in the interim that they would then use to replace. The control panel came in October the 22nd, was replaced and the new board was faulty, put old one back in and re-ordered another board. The part was on back-order. By mid November, after numerous calls, we called Whirlpool directly. They authorized that the technician to get the part from another supply source. On November the 26th, technician came back - tried new board could not get it to work, left it with us and ordered additional parts. At that time the technician who was taking the case had a family emergency and would not be able to come back out until the new year. Subsequently, Appliance Canada authorized a new company to resume our work with a new technician (Toronto Appliance). He came out December the 17th, with the board that was left behind, he was able to get the oven working. December the 22nd while in the middle of cooking a meal, the oven failed again. We called Appliance Canada and they had a Technician scheduled to come December the 24th from Toronto Appliance. However, on December the 23rd the oven resumed working. The Technician came on the 24th but because the oven was working again could do nothing. On December the 31st, while dinner was in for guests, the oven failed yet again. We called Appliance Canada, yet again, and they scheduled another visit with a new control panel and additional board. The technician arrived again today, January the 28th, and could not get the stove working. He was instructed to order an additional part and we are to wait another 2 weeks. In total, we have been waiting for 4 and a half months, we have also been told that we were not to have used the self-clean as this causes these types of problems. Why is it offered, in addition, Whirlpool has not supported our direct calls, nor authorized the replacement of a product, that for all intents and purposes, is faulty. We have had no success in the resolution of this issue nor support to reach a resolution from all parties involved. I would suggest not buying any product from those involved as their lack of support for their product is appalling.

Weve had the 3 door model (side by side fridge with chilled water inside and full width deli drawer, freezer on bottom w/ Icemaker) for 13 months now with absolutely no problems. Chilled water inside frees up door for more storage.

I purchased the washer and dryer set. My complaint is with the washing machine top loader that does not have the tall agitator not getting the clothing clean. All of my clothing come out of the dryer with dirty spots on them where they did not come out in the wash. Its a waste of water and energy because I have to wash them twice! I purchased the combo model numbers WED7300DWO and WTW7300DW0.

I purchase Whirlpool refrigerator. After a year it has done nothing but give me problems. Thank God I purchase insurance for repairs. I had the refrigerator fix over 3 times. First the water and ice wasnt working so the filter had to be change. Then the ice was made and my refrigerator start leaking. The repair guy stated the fan and something else is not working. I am a single mother struggling and to spend over a 1000 dollars for a refrigerator that does nothing but give me trouble. I am totally unhappy with this product.

Looked for the best refrig we could find and it turned out to be a piece of junk! Less than 3 years old, paid 2700$, french doors bottom door freezer. It started making a lot of noise it seem to be coming from freezer. Called Whirlpool, they said to clean coils. We wanted a repair company to come out. They set an appointment for next Tuesday between 12pm and 5pm. Said ok.Was making so much noise, and no longer freezing everything so call said company. Lady was very rude, and said they would not be out on Tuesday but sometime the following week. This would not work for us so called another repair shop, said they would be out. They were here before 6pm. Found out that they have been having this problem, had same type of call already this week. Repair for this problem would be over $1100.00. No thank you! Would just as soon junk this appliance. So very sorry we wasted our money on this.

If I could give half a star, I would. I purchased a Whirlpool dishwasher. Once installed, it leaked immediately. Thinking it is best to call Whirlpool for repairs under warranty, they decided to send out a technician from A&E Factory Repair. This is where the service sucks.A&E needed me to wait about 2 weeks for the first available appointment for service. When the technician arrived and pulled out the dishwasher, he told me that he would not repair it because he didnt like where the hose was installed through the cabinet. He insisted that only after the hose was moved, they would return to fix the leak if it was still an issue.Of course, the hose was then moved and the machine still leaks. So, I called A&E back to schedule another service call. I was again told that the next available service call was 2 weeks out.Now, the day before the service call, I receive a phone call from A&E, telling me that they have to reschedule the service call that is supposed to be for tomorrow. Once again, the earliest next available appointment is another week out.If it was now not past the original 30 days to be able to return the item to Lowes, I would have already done that. By the time the first A&E service call happened, it was already past the 30 days in which I could have returned it to Lowes.I will never purchase Whirlpool again simply because they use A&E service center.

Bought side by side in 2010 and after the first 3 mth the ice maker jammed up. Found out the dispenser door was not working right so it was change. But lo and behold the dame thing jammed up again within 3 weeks and the door is working. I will never buy WHIRLPOOL AGAIN. I hope they go out of Business. They are selling junk and they do not care. Made in American. Pack your bags Whirlpool. You are no longer needed.

Thirty minutes into running the oven self cleaning cycle for the first time, the middle pane of glass exploded! Weve had this range two years 4 months, and didnt buy the extended warranty. I contacted Whirlpool and they acted like this was the first theyve heard of this. I inquired on the class action law suit in New York from 2012, the year we bought ours, and they had no comment. They were willing to sell us an extended one year warranty and we pay for the service call for only $332! I declined and will never buy a Whirlpool product again.