I purchased this washer 3 years ago. At year 2, I had to replace the RPS part. The codes that appear represent 2 different issues as well: one being the RPS part and also for the control panel. In less than 1 year since this replacement, it is broken again! The clothes do not get very clean. You cant soak whites in hot water and bleach (it drains after 5 minutes if you stop it). You have to use the bulky setting to get enough water to actually wash your clothes. If you get too much detergent, your clothes comes out crunchy feeling even with the extra rinse.I thought this Whirlpool product would be great since my 22 year old dishwasher is a Whirlpool and still works but as the old saying goes... They dont make them to last like they used to. To say this washer is a POS Lemon is an understatement! I also have the companion dryer and it is starting to have problems including the door latch breaking into pieces. I will never purchase another Whirlpool product again! I have been told that Kenmore and Maytag are also under the Whirlpool umbrella so Im not sure what I will buy next. My recommendation: DO NOT BUY THESE PRODUCTS!!!

Purchased the Cabrio top loading washer and dryer. Huge mistake. The clothes come out of the washer a tangled wrinkle mess. Have tried different cycles and water levels to no avail. Dark clothes have detergent streaks and lint. The dryer has a steam refresh cycle which Ive used to try and remove some of the wrinkles caused to no avail. Clothes come out with water spots. Ive only owned this dual for about 6 months. Take my advice and DO NOT PURCHASE!!!

I’m getting the run around with service. No one comes to our area to check our new Whirlpool hot water heater. The hot water heater has not worked right since I installed it. I need a service tech to come to my house at Whirlpool’s expense and check the damn thing and get me taken care of. Does Whirlpool want to retain a customer or not? Its that simple. My cell phone number is **.

I made the mistake of buying a whirlpool product and was wondering if there is a support group for angry unsatisfied customers? I have owned a duet washer and after 2.5 years is giving F1E2 error and is junk.

We have a Whirlpool Quiet Wash Plus dishwasher thats been doing a great job cleaning our dishes for just shy of 24 years. We use a cleaner every 2-3 months to keep everything cleaned out and sanitized. We use a liquid detergent and a rinse aid and the dishes come out clean every time. We feel like weve been blessed with this machine and would definitely buy Whirlpool again.

In 2007 our Whirlpool 30 gallon gas water heater began to have issues. Serial number 0425126675, Model Number FG1F3030T3NOV. The pilot light kept going out and would not stay lit.. After several times with replacement parts being sent with the same thing happening, finally in 2010 they replaced the water heater. A new water heater was professionally put in, serial number 1023T412357 Model number BFG1F3030T3noHV.I am having the exact same issue and I was told that the warranty was null and void on the new water heater because it was a replacement. They replaced a defective water heater with a defective water heater. I called the number given to me by Lowes 1/877/817/6750. I spoke with Nichole. I told her that I should not have to pay for replacement parts for a defective water heater. I told her that I was never informed that there would not be a warranty. I live on a fixed income and cannot afford to buy another water heater because I was given a defective water heater in replacement for a defective water heater. I became angry stating, Thanks for nothing and I hung up. So many people have the same problem with these water heaters that something MUST be done.

I really like the microwave. It performs all the preset functions very well. I’m not that thrilled with the refrigerator and dishwasher though. I do live in an apartment and I’m sure they are cheaper models of these appliances.

We have all Whirlpool Appliances throughout our entire house. Our refrigerator fan went out and we had someone come out to look at it. We called to get a parts concession as we were a few months out of warranty. We didnt ask for 100% discount, but SOMETHING considering weve put so much money into our whirlpool appliances. They simply said, We can give you nothing. Long story short, we will not purchase whirlpool appliances ever again. Dont do it, they take your money and run!

This morning is the fifth morning I had to take a cold shower. My hot water heater keeps going out. When we call, we are told to dust the underneath better, as it sucks dust. Are you kidding? The hot water heater is still under warranty, which means I will have to spend around $200 to have repaired again. So much for top of the line.

I love my Refrigerator. It is a side-by-side with ice-maker and water in the door. I have plenty of room in the refrigerator, and I really like the adjustable shelves. I would definitely purchase another Whirlpool (next time with freezer on the bottom). I love the Stainless and would probably purchase again - or depending on the kitchen maybe black.

There is a melted hole in my Whirlpool microwave. The model WMH53520CS is on the recall list for this but not my serial number. Other have posted this and theirs was not covered. This should never happen. I have never had a microwave do this. If I have to replace it I won’t buy Whirlpool ever again.

Whirlpool Cabrio - Clothes come out of the washer wrinkled, twisted and soap stained. I use the exact soap products they recommend in the proper amounts. Bought them in September of 2014. Wish I could return them. Too low of a water level that cannot be adjusted. Not fully rinsing the soap out of the clothes. Washing takes twice as long as with my former 25 year old washer. Dryer is new technology and energy efficient yet wont remove wrinkles from permanent press clothes.Uses hardly any water so clothes must be rinsed at least one or two times to get the soap spots off. Clothes always come out extremely wrinkled. Not all items can be put in the dryer so ironing is back in my life again. Some items come out so twisted and wrinkled that ironing wont even help. Dryer isnt much better at all and shirts and pants always have some wrinkles. Have had to bring some items to the dry cleaners to bring them back to a non wrinkled state. Whatever is saved in water and energy is more than made up by ironing and dry cleaning. The company representatives have sent service people out twice and they both said that the machines are performing as they were intended to. I do smaller washes and wash more often to try to get better results. I dont. Even though it is extra large capacity items such as blankets must be washed more than once as the water does not wet the entire blanket.

After one of the door shelves in our new refrigerator cracked, I ordered a new shelf from our local agent Neuman Appliance repair in Ashmore, in July of this year (2014). I was told that it would take a while as Whirlpool were notorious for poor service; however, it is now the middle of September, and we are still waiting!When we ordered a new part for our dishwasher from Fisher and Paykel, we received the part in just 3 days. I mention this to give an idea of what good service should be.

I purchased a new water heater in August 2013. The pilot light started going out in October/November of 2013. After calling the Tech Support phone number, (877) 817-6750, I was advised to clean the burner screen. First this is very difficult to do because the burner screen is underneath the water heater and almost impossible to access. Second the closet the water heater is in did not show any signs of debris that could clog the burner screen. I did as they recommended. Several calls, and several weeks later, they finally authorized a technician to come and service water heater. He performed a cleaning even though he couldnt find anything to clean; and he replaced the control module. The new control module worked through the spring and summer seasons and then I started having issues again in the fall, late October. Started calling the same phone number and was told again to clean the burner screen. I convinced them to send out the technician again. The A and E Factory technician came out and only cleaned the burner screen and left before I had a chance to get home. This happened several times and I called Whirlpool every time. The next A and E technician told me to try changing out the draft vent chimney to a different size, which I did. Problem happened Again! I finally asked for another plumber and they sent me 3 names of their authorized plumbers. I called Phil, Philco Plumbing. He told me that I needed to have more ventilation, so I added more ventilation, even though I later found documentation stating I already had more than what was required by the manufacturer. Again, a week later, started having problems. Call back and asked to have my personal plumber come out. This time the rep told me that I have always been free to choose any plumber I wish (why wasnt I given that option the first 10 times I called?). My plumber came out and replaced the control module and the thermocouple, but wasnt convinced that these were faulty parts, he honestly couldnt figure out why I am having this problem, but it was worth a try. That lasted about 1 week and now I am having the problem again!!Whirlpool will FINALLY authorize a new water heater, but they will not authorize installation for the new water heater. I have already spent money on recommended repairs that have not worked. I have taken 15+ hours off of work to watch plumbers do nothing that has rectified my problems. And now Whirlpool wants me to deal with installing the unit myself, OR pay to have it installed! They say they wont cover installation because I purchased it more than 1 year ago. They seem to be missing the fact that I have had trouble with it the ENTIRE time I have owned it!This Flame lock system is garbage. I found on Consumer Affairs that a few years ago a class-action lawsuit settled, dealing with the same issues. I think it is time for another round! I KNOW that I am not the only one dealing with this problem because the plumbers I had out all had similar complaints from many of their clients. Whirlpool wont fess up to the problem, but the problem is real.

Our burners broke down just 3 months after having purchased a new Whirlpool stove. Then a week later the oven broke also. I want my money back now. Do not purchase any Whirlpool products. Theyre garbage.

I purchased a matching set Whirlpool Cabrio top load washer and dryer in 2007. Bought from Conns for $2,100. After 3 months of ownership, the circuit board had to be replaced on the washer. Three months later the heating element was replaced on the dryer. Just recently I spent $350.00 to replace 4 drum suspensions. The washer literally shook my home. 3 weeks later, the circuit board needs replacement (code F1). Estimate to repair - $325.00. The dryer is not working properly. Im having to run the clothing thru 2 cycles. Back to the washer. It shreds my towels. Ive read where other consumers have had this same problem. These are expensive towels. So, only 7 yrs. into ownership and I am replacing this junk with the old school washer/dryer. Unlike the Cabrio washer, I will have a washer with an agitator that will actually clean my clothing. Whirlpool manufactures trash and the Cabrio duo was the worse purchase I have ever made. Do not purchase Whirlpool and definitely do not purchase Cabrio.

Just bought 4 new whirlpool washers and dryers for my new four plex I am building for clients. Two of them leaked violently along the wall and downstairs. Did I see they were BRAND NEW. Total garbage. Now I have to pay for servicemen to come and fix it. NICE AND THANK YOU for your poor quality commitment. Now my clients are pissed off because they cant move in because whirlpool makes garbage material. So the extra cost it has cost me is totally unthinkable. Whirlpool, ask me if will buy from you again. Thanks for ruining everything due to your inconsiderate quality levels.

I purchased a 40 gallon water heater at Lowes and installed about 3 years ago. A couple of weeks ago, it got an upper sensor failure code on the gas valve. It would heat by resetting (turning valve off, waiting a minute and then lighting) but after a few minutes, it would fail again. I called the customer service and they mailed out a new upper sensor. When it came a few days later (I paid for shipping), I installed it but the same failure code. Again, the only heat I could get was by resetting the valve several times before a shower. I called customer service again, told them what I did and they said, Oh, the problem is the gas valve then. So they mailed out a new gas valve unit. It then came a few days later and I installed it according to the enclosed directions to the letter. Still got the failure code and still had to keep resetting it to get any warm water before a shower.I called customer service again, told them what I did and he said, Well, did you flush the water heater with apple cider vinegar before you installed the new gas valve? I said, No, it wasnt in the enclosed directions to do so. He said, You should have done that and it would have worked. I will send out a new gas valve. At this point, I blew up. Two weeks with no reliable hot water. I told him I want a new water heater and he refused. I asked to speak to his superior. He said no. Dont ever get a Whirlpool product. Some other crappy company builds these turds.

We purchased our oven on 12/06/15. I have called and complained about the AquaLift oven on more than one occasion. This technology does not work. I would have thought that there would have FINALLY been a recall on this oven. I am a senior who thought this stove would last me for the rest of my life. I have to stand on my head to try to clean it. NEVER, NEVER, NEVER would I have purchased this if I had read any of the reviews. Buyer beware!!!

I purchased the front load washer 4 years ago and the board went bad in 2 years. It costs more to fix it than the washer is worth. Stupidly, I purchased the top loading Cabrio and it has gone downhill from there. Has always sounded like a jet taking off in the spin cycle. Then 18 months into the purchase, it started with grinding noises and load balance issues on the spin cycle. Seems like they have a lot of issues with these Cabrios. Spent a lot of money for nothing. I will never buy a Whirlpool again!!!

We bought a Cabrio washer & dryer September 2010 for a room addition that wasnt completed yet. We didnt get moved in until the first of November. So the washer wasnt used until then. In January 2011 (15 months later) it stopped spinning so clothes were dripping wet. We called Whirlpool and were told that they would be happy to set us up for a service agreement for $322 for one year. We declined since we bought the washer for a little over $500. When we had a local Whirlpool service man come out and he determined that it was the control board which would cost $265 (Whirlpool only warrants parts 90 days). I sent an email to Whirlpool and was told too bad, so sad. We called their customer care line (that is really not the term for that phone center) and asked to talk to a supervisor, who essentially told me the same thing. Whirlpool is making equipment that is extremely poor quality. There is no incentive for them to produce a better quality product as they make money on the extended warranties that are necessary, or if you dont buy an extended warranty they charge an extraordinary huge price for their parts, which they dont warranty. We will never purchase anything made by Whirlpool. I am not sure where this useless piece of junk that I have will end up but I intend to let everyone I know what a terrible company Whirlpool is to deal with.

On July 30, 2009, we purchased a Whirlpool Gold French door refrigerator with the freezer drawer on the bottom. It was delivered on August 1, 2009. On August 3, 2009, the ice maker and water dispenser stopped working. After three unsuccessful service calls and the installation of various replacement parts, Whirlpool gave up the effort to fix the ice maker and water dispenser and delivered a new replacement refrigerator on October 15, 2009. Todays date is April 14, 2012 and here we go again, the ice maker and water dispenser stopped working. Luckily, I purchased a five year warranty on the unit. However, after reading all of the posts about fire hazard issues and other various issues with Whirlpool refrigerators, well probably go out and buy a new refrigerator and write-off the $2,500 that we spent for this refrigerator as a bad investment. We purchased a Whirlpool refrigerator based upon their reputation of providing sound products. However, based upon this experience, I can guarantee the folks at Whirlpool that our next refrigerator purchase will not be a Whirlpool product or a product of any subsidiary of Whirlpool.

The new? improved model with NO center agitator is the worst - clothes tangle badly and the load becomes very unbalanced, wobbly and noisy. How I got talked into this model by a Sears salespeople was a big mistake!!!

Read reviews on the same washer (Cabrio Whirlpool) that I had purchased in January 2017. I have the same problem everyone else has with it, not cleaning the clothes. It was such a disappointment. Had a Whirlpool front in loader for 15 years. Loved it! But the washing machines without the agitator on it is a laugh. What person thought up that design. What a joke on the poor unknowing people that purchased one. Im also upset at G&H Appliances for not standing by their products they sell. Found out that Lowes has a 30 day satisfaction guarantee on what they sell. Not buying from Lowes and buying a washer without on agitator on it. Was two big mistakes I made. I wanted to help out a small local business, but wont be doing that again. They sure are not worried about me.

After reading many of the 1,500 +/- complaints about this inferior product, I guess I should consider myself lucky. Ours didnt fail until this past Saturday, March 22, 2014. We purchased this Whirlpool (American Water Heater Company) water heater FG1H4040T3NOV at Lowes, and had it professionally installed, in October 2004, and we have had no issues until this past Saturday when we woke up to no hot water. After checking for the obvious, and finding no apparent cause for the failure, I considered it a fluke and relighted the pilot. The pilot took a few attempts to light, but it lit, and the burners came on.Three days later, we woke to no hot water again. This time, we placed a service call to the company that did the initial install. The technician came out, and after his inspection he informed me that the thermocouple/burner assembly needed to be replaced. He also informed me that this is a well-known issue, and Whirlpool has been sending out free updated replacement parts. He called Whirlpool, only to be told that they are no longer offering free, updated parts. Whirlpool also cited that the water heater was out of warranty (by less than 5 months). He gave me Whirlpools number, so I could contact them myself.As I smelled a rat, I began to do some online research about this issue, and, to my chagrin, I found out that I was far from alone with this issue. As of this writing, 1,500+ consumer and professional complaints, a settled class-action lawsuit, etc., etc. I contacted Whirlpool, explained my situation to the support rep, and, he proceeded to tell me that he couldnt help me with free replacement parts, due to the warranty being expired (less than 5 months). I argued with him, stating that this is not a warranty issue, but is in-fact a design/manufacturing defect issue, that has resulted in a redesign/re-manufacture. I cited the myriad of online data and negative testimonials, and I reminded him about the settled class-action lawsuit on this very topic. He acknowledged all of the above, was unimpressed, and offered to sell me the parts.After 15 minutes of back and forth, I asked to be escalated to the next level. But, of course the supervisor was unavailable, and If Id care to leave my name and number... yeah, right. Bottom line, Im very angry! I paid good money to Lowes for Whirlpools product, with a nine-year warranty. I had it professionally installed, and we have no hot water due to poorly designed parts. And... I am being forced to purchase the redesigned parts. Its truly unsatisfying to be an American consumer these days!

In 2010 we had to purchase a new hot water heater. Went to our local Lowes store to see what they offered. We decided to buy a Whirlpool energy smart electric water heater. It was large, 50 gallon. We have a large family and didnt like running out of hot water so we thought this would be great. Worked fine until yesterday when I kept smelling an odor like something melting. Could not figure out where the smell was coming from until this morning I got in the shower and had very little hot water. Went downstairs and seen the water heater was not working. Got the user guide out to see if we could pinpoint what was wrong. It said no power to control board. I checked the breaker box and found no problems. I got a flashlight to look at the control board and discovered it had overheated and melt the top of it. Have been on phone with Whirlpool nonstop with just a recording. The heater has a lifetime warranty so Im trying to get the replacement part for it that will cost me $115 plus shipping. I am really concerned that with this overheating it did not trip the breaker. Grateful it did not start a fire and worried if we repair it will this happen again and possibly not be as fortunate. I have seen on this site of another complaint with the same problem. Shocked there hasnt been a recall issued. Be careful!

We bought this dishwasher new from the Brick 2 or 3 years ago. It was bought not because old dishwasher wasnt working, but we needed a new fridge and stove so we also bought a dishwasher to match the new stainless steel fridge/stove. If I could give 0 stars I would. Biggest complaints: It doesnt matter what soap, what setting or how much your rinse/scrape your dishes THIS DISHWASHER WILL NOT CLEAN THEM. Its very rare it actually cleans a dish or utensil properly. If your plate had ketchup on it, it wont clean it. But if you had a sandwich on the plate and managed to not get ANYTHING from your sandwich on the plate, it would come out clean.The drain constantly clogs. We rinse everything, but the drain hose constantly clogs to the point the unit wont drain. Have to remove the unit, take off hoses and blow them out. It clogs because the strainer at the bottom of the dishwasher which is supposed to stop stuff from going down the drain hose doesnt work. If you look at the strainer and the system they use to stop stuff from going down the drain hose. Its no surprise it doesnt work. By design it cant work. My brother in law is a licensed appliance repair man. Sears actually paid for his schooling. He installed and hes fixed the clogged drain numerous times. He agrees. Worst dishwasher ever.

I had a Whirlpool oven for 14 years. It worked great and the control board burned up during the cleaning cycle. I purchased a new whirlpool oven that did not have an exposed bottom heating element. It takes way too long to preheat and if during baking, you need to change the temperature, it starts preheating again and the displayed temperature is lower than the original temperature that was set at the beginning; and it takes too long for the oven to reach the new temperature. This appears to be the result of the bottom heating element being hidden. Heating and maintaining a consistent temperature is far more important than being able to clean the bottom of the oven especially when this is a self-cleaning oven.Updated on October 20, 2015: This is an update on my last review. I was cooking a cake at 350 degrees and when the designated time was up, I opened the door to check for doneness. The cake needed to cook a little longer, so I closed the door and the temperature immediately went to 300 degrees and started preheating again which of course caused the oven to get too hot for the cake I was baking. Who is designing these ovens??? Certainly not a person that cooks on a day-to-day basis. I will never buy a Whirlpool oven again.

I just finished a call with Sears Repair. I informed them that this was the 5th service call since purchasing this Whirlpool Cabrio washer two years ago. The washer simply does not work. It fails to complete its cycle; fails to spin; fails to drain; fails to fill; leaves clothes streaked and dirty, smelly, and dripping wet for me to wring out by hand. I purchased it because of my faith in Sears and its Energy Saver label. I often have to wash the same load 2 or even 3 times to get it clean; no more than 6 towels at a time. (It is a large capacity washer, but acts up most often when washing towels or jeans.)Im a retired teacher; and in my best teacher voice – calm but serious – said that I would like Sears to come and take it away, issue me a credit or refund, or I would proceed to file with the Small Claims Court. His immediate response was, I dont appreciate the threat. I carefully (teacher voice) explained that it was not a threat... it was information. Yes, Im angry. But more than that, I am so disappointed in Sears, a company that I have always been loyal to – no more. Time to leave childhood behind and wake up to the reality that this is not the same Sears Ive dealt with for the last sixty years. Now, I’m to drive 25 miles of country roads to a Laundromat.

Whirlpool Energy Efficient Top Loader - I re-wash at least 20% of all clothes because they have dark spots AFTER washing them, but NOT before! It is a moving target, wash out one dark mark; get another somewhere else. I bought great quality sheets that are permanently stained, because of this. No matter how you load this machine, anything with arms and legs gets entangled into a big knotted mess. It is difficult to separate them and time-consuming. This puts a lot of stress on the clothes, especially as the load spins. I also re-wash entire loads at least 4 loads because the clothes dont rinse properly. I bought a 5 yr. extended warranty and have had this serviced at least 4 times to no avail. THE PROBLEM IS IN THE DESIGN! I am POSITIVE of it. If you have these problems, as well, please contact me. I would love to investigate a class action suit. I am THAT mad.

I have had my washing Machines since 2011 and have had continuous problems with the washing machine during spin cycle sounding like a freight train going through my house. Whirlpool has had people to my house 5 times to fix. When warranty was up in 2012, I was told they would continue to cover this particular issue. They came out again in April 2013 and now I am being told, Too bad; if you want fixed then you will need to pay for it.

I have been buying refurbished appliances and this one we bought it brand new. Its a great buy and it will last a while. It does a good job washing and the clothes come clean and almost dry to the touch.

Electric hot water heater model E40H6-45-100 - Purchased at Lowes. Husband installed, tank filled, no hot water coming through house lines. Called support center several times after trying each recommendation that did not work. They kept saying it was a plumbing problem. My husband is very smart when it comes to electrical and plumbing. He has done numerous repairs to our homes over the last 30 years we have been married. He knows what he is talking about and told the support tech that he believed it was a faulty water heater. She immediately said the units are all tested before they leave the factory. The final step was to remove the nipple that the hot water flows through out of the tank and remove the two black bellows. Now my husband can see directly through the piece but also decides to put his finger through the the open whole on the top of the tank and cannot get his finger through - it is blocked. He gets a flashlight and a screw driver. Puts the screw driver through a thin plate that was blocking where the water should be coming through. He can now actually see the water in the tank. This was the whole problem! So they could not have tested this tank. They did give us a ref number to take parts back to store to replace parts we already bought and cannot use. Its the time and energy on whats suppose to be an easy job that counts. Will not recommend Whirlpool products to anyone and probably will not purchase any in the future. Ours was not as bad as most of the other reviews I read but wanted to advise others who may think about what brand to purchase.

Its a great machine but the temperature control button is easily moved at times. The machine does a great job in washing clothes. Ive had mine for 10 years now and hope that I never have to replace it.

Approximately 2 years after purchasing a Whirlpool Gold Bottom Freezer refrigerator, I noticed cracks/openings on the interior walls on the ledge that holds the glass shelf! It is completely Crushing the styrofoam inside the refrig? Also, signs of being Cheaply made veggie bins are held in place by a piece of plastic that cracked after a few months. This was in 2011. First, I contacted the service contract people. They told me this was not covered under the policy. Next, I wrote & called the company. The walls show the styrofoam stuffing in the refrig. The shelves rest on these openings in the vinyl walls of the refrig box. This is a disaster and the refrig was 1400$$$. I have extended warranty which does not cover structure!!! What can one do with a New expensive refrigerator that has cracks in the Wall of the refrigeration box? Is there a class action suit anywhere that I can join?

I just bought my washer 3 or 4 months ago. It is the worst washer I have ever owned. Anyone that has ever done laundry knows you need water to wash clothes. My clothes are not clean and my whites are very dingy. I use the same soap (Tide) and the same bleach (Clorox) that I have used for years. If I can find someone dumb enough to buy it I will sell it and get a good one. I would rather go back to the old wringer washers than this one.

I purchased a Whirlpool hot water heater 2010 and it started having problems 2014. I called customer service. They informed me my 6 year warranty was only for parts and I had to pay for a certified repairman to come and do diagnostic tests and they will pay for parts only. I said the repairman is half the price as the hot water heater and then he has to come install it. Woman on the phone was just as ready to get off the phone as I was! Save yourself and just buy a new one NOT WHIRLPOOL!!!!!!

Right at 18 months ago, we bought the Whirlpool Cabrio Top Load washer. The last washer we had was the bottom of the barrel Whirlpool model and it lasted 8 years. So, I had no problem purchasing the brand. But now, our washer wont go through the cycles and we hare having lid lock issues. The repair guy said the lid lock was fine which I thought was good news because he said it would be $300 to replace including his service call. Now, it looks like our choice is a $350 motherboard, or a new washer. Whats wrong with this picture? I can go to Lowes right now and buy a used one (exactly the same for $399), pay $350 to repair my two-year-old $750 washer, or buy a different washer? Its hard to believe that a $750 washer is only good for 2 years.

We bought this Cabrio washer WTW6400SW2 several years ago. Immediately after having it delivered and installed, it started displaying an F1 fault code. The main control board was replaced under warranty. It happened again within six months. Another board was replaced. That board lasted another six months. The warranty was up by then, so I used the machine by hovering over it and restarting it every time it failed. After two years of this piece of junk, we put it in storage while we worked on the road. It was brought out on 10/01/11. I called a repairman (who came on 10/04/11) to come replace the board again. He told me that the last two times it had been replaced with the same defective board, that Whirlpool had never fixed the problem. He claimed he had the new improved board, which he replaced for about $350. Two days ago (361 days later), it went bad again. The same repair company came back and said it was the board again. I just tried chatting with a person working on the Whirlpool website. They (of course) said they would do nothing about the washer. They do not stand behind their product, obviously. Does anyone know of a class action lawsuit over these washers? It is a ridiculous amount of money to spend for a product that does not work. This is just wrong!

Lost two freezers of meat in this Whirlpool. Changed Motherboard twice. Wouldnt keep ice cream frozen. Tech told me I was buying cheap ice cream. Was told by Whirlpool that they dont replace freezers. Received a call from another WP rep who did replace it. Waiting 4 weeks now because trucking company wont come up my driveway in snow. It was here once out. Driver didnt know how to change unit out. Waiting for exp driver now.

I purchased 3 appliances (microwave, stove, and dishwasher) on 10/22/10 when they were on sale at Sears for my soon to be remodeled kitchen. I did not have them delivered until 11/15/10 until contractor was getting ready for them. They still were not installed immediately. On 11/17/11, in the evening, the microwave stopped working. I called Whirlpool on 11/18/11 for service. Whirlpool will not honor the 1-year warranty since technically I bought them in October 2010 but did not even have them installed in my home for use until the end of November or beginning of December 2010. Common sense tells me the company should honor the warranty. Are products being made today to last less than a year before they go bad? To pay for a service call and parts, I can buy a new microwave (but you can bet it wont be Whirlpool).

We owned our Whirlpool Gold refrigerator GS6SHEXNL00 for 23 months when our electronic control board went out resulting in the light and interior temp display to go out. I called Whirlpool and they told me the control board was not under warranty. I subsequently replaced the board at cost of $156. This morning, 7 years from when I bought the fridge, the control board went bad again. Amazon now has a replacement board W10135090 for $67. There are thousands of complaints regarding the Whirlpool electronic control board, which Whirlpool just ignores. This should be a recall item. I will not buy another Whirlpool product.

We purchased 4.0 cu. ft. Cabrio Top Load Washer with 6th Sense Technology MODEL WTW7340XW2 on 11/20/2011. We are a small family of 3 so use of the machine is light. We noticed a strange sound and some leaks a week ago and called in a technician recommended on the Whirlpool website. To our horror he informed us that we need to replace the tub bearing assembly, rotor and stator - to a cost of $1095! This machine is not even 3 years old. Did we buy a lemon? I called Whirlpool. They were simply not interested. The online chat person sent me to the Whirlpool Customer Experience Team where I was told that I should buy an insurance plan to cover the costs of repairs. They then sent me on to the insurance department who want me to pay $338 to buy a repair plan to have the machine fixed. And then referred me to the Manufacturing division when I wanted to know how to escalate the problem - and if you call that number - there is no option to deal with problems - seriously?!? Is this what I should expect when buying the Whirlpool brand?

I purchased the unit in May 2012. Right out of the box on the first day, the tank was leaking water from where pressure relief valve screws into the tank. Whirlpool replaced the part from my local Lowe’s store which I had to go get on my dime and install myself to solve the problem. Its now the 2nd week of January and the water heater is dead. I didnt even get 8 months out of this water heater that has a 12 year warranty. The electronic thermostat died, and I will be going 3 to 4 days without hot water until Whirlpool can ship me another thermostat. Nothing like taking an ice cold shower in the middle of winter. Like I said, buyers beware!

I replaced our old 50-gal water heater (10 years old) with a new top-of-the-line Whirlpool 50-gal water heater in Feb 2011. The Friday before Memorial Day, the heater went out and the pilot refused to stay lit. I called and jumped through all their hoops and finally figured out that it was the gas valve, because the pilot goes out as soon as you release the button and the milli-voltage reading is ok. They sent me a replacement and it cost $145 to have a plumber come out and install it. We were without hot water for 5 days. Now 9 days later, the pilot keeps going out. This time I can re-light it, but after the water heats up, it is apparently going out again. They refuse to replace a 12-year warrantied water heater that is only 2 years old and I am going to have to hire a plumber again to come out and attest to what we already know. This water heater is extremely loud. When we had it installed, I read the reviews and there were similar complaints (sounds like a mini jet engine). We dont seem to get as much hot water as we did with our old builders grade heater. This is a bad buy and I would advise anyone looking to purchase to look elsewhere.

The Whirlpool engineers need to go back to design room sober on this machine. It is only a year old and still I have to run one load two sometimes three times just to get clothes clean. How is this energy-efficient? I have tried all of their so-called remedies. Paying such good money for a lousy and lazy appliance is hard to swallow!

I purchased a Whirlpool gas top range from Lowes in Somerset Ky September 2013. Model number WFG524SLAB1. The surface is showing bubbles. I contacted Whirlpool and they gave some kind of story. In other words I am stuck with it. Still under warranty but they wont send someone out to look at it. Lowes told us that it could be a paint defect when it was made. If the top starts peeling, it will be a real mess. I have never used anything abrasive on the stove top. As of right now I am not happy with Whirlpool at all and if they dont do something about this, I will never buy another one of their appliances.

I work on Whirlpool refrigerators for a living every single day of my agonizing, miserable, lousy life. Ive never seen such a mass of dysfunctional, defective rejects as I have with the new Whirlpool side-by-side refrigerators. The ice maker never works because the water line always freezes in the door. The food in your refrigerator side will either spoil or freeze because the damper door will stick open or freeze shut. The water filter housing will start leaking before you change the filter for the first time because of the inferior quality of the plastic its made from. And of course my all time favorite the compressor will always go out under the first 5 years (Thats why Whirlpool changed the warranty from 5 years to 1 on the sealed system). Ive never been a big extended warranty believer. But, like old saying goes, They just dont make them like they use to. Definitely applies to Whirlpool refrigerators.

I bought this Whirlpool Cabrio Washer 3 years ago. Yesterday will be my last repair. I installed a new tub (bearing failed have to buy a full tub to replace), new suspension rods and a new stator and rotor (cracked). Last year I replaced a drain pump twice, and a computer board. All of these repairs since I purchased this washer have cost me well over $900 for a $1400 machine. I dont mind replacing a pump every few years but these larger failures are unacceptable. We have moved back to Kenmore on some new appliances we purchased this year as result of trouble with Whirlpool. Whirlpool should send out a recall on the suspension rods; the existing ones seize at the top and stop functioning causing the tub to shake excessively. This led to the cracked motor (rotor cracked).

I love my Whirlpool 4.7 cu. ft. top load washer because it has a pretreat station that is super handy for pretreating stains in a handy little place. The agitator is stronger than my old washer and really gets my clothes cleaner. Its also very quiet and easy to use all the buttons. The best feature is the deep water fill that you can select for more water.

We have had nothing but problems out of our refrigerator in the past 5 months. We purchased it a year ago in April and they have already replaced 7 parts on it. It still doesn’t freeze, and we have no ice... We will NEVER buy another Whirlpool product ever again!!!

You have to take into account that this microwave doesn’t heat up as others I’ve had so even if the instructions call for something to be cooked for 5 minutes, you have to add at least 2 minutes more. If not it would be undercooked.

We had the unfortunate experience of purchasing a Whirlpool product from Lowes. During Memorial Day weekend we came home to a freezer full of defrosted meat. After having to throw away 1/3 of a steer that we purchased from a local 4-H students project due to the temperature of the meat and not knowing how long it had been at that temperature. I called Lowes and they said there was nothing they could do for me since the freezer was over 1 month old. It was right at 2 months. (Purchase date - failure date). They advised me to call Whirlpool directly and gave me a number to the warranty technician. The warranty technician came and immediately found the problem. The defrosting connector was not plugged in when it was manufactured. Clearly a manufacturer issue. I called Whirlpool to find out how much of my over $1500 of meat they would cover. They told me they would not cover any of the loss. Then they offered me a 1 year extended warranty for free for my Inconvenience. What a slap in the face. Why would I need a warranty or even a freezer for that matter since I no longer have anything to put in it. Needless to say I will no longer purchase any products from Lowes or Whirlpool.

My Whirlpool range is a great buy and it cooks well. I have never had a brand new range that snaps, crackles, and pops. It was letting me know that it needed to be broken in and used for a while. I have had it for a few years now and it is just now getting broken in well. I do not even smell the brand new burn smell it use to give off anymore. Awesome!!

Cabrio washer and dryer are not energy saver by any means! Have had the pair for almost 1 year and have spent at least 3 years of washing and drying time with these. What use to take 30 minutes to wash now takes at least 48 or more and the dryer has to be run twice on lots of loads to dry! The other thing is, with no water in the tub it really does not have a soak cycle to get really dirty stuff clean, so you wash things 2 or 3 times! Now I know why I see these washers and dryers like new in the used stores for $200 to $300. Thanks for the junk Whirlpool.

A few months ago our Whirlpool microwave just completely died. We had only been in our brand new home for about 18 months at the time, so I was very disappointed. I would have bought a different brand at that time, but didnt want it to look ridiculous, as it is mounted in the cabinet above the Whirlpool oven I was shocked to get a text from my wife a couple days ago, saying the same thing had happened to our oven. I thought that it must be a circuit breaker. My parents had Whirlpool appliances in my home growing up and we never had a problem with our oven. Well... I was wrong not a circuit breaker. The thing is just dead. Nice... Thanks Whirlpool! Thanks Century Communities for installing the absolute cheapest products in my home! Wonder what will be next? Probably the range top... Ill let you know.

I bought the most deluxe and expensive washer and dryer I have ever owned. It is a Whirlpool Cabrio. The clothes come out of the washer dry, and all tangled up. I bought it new from Sears on July 2009. Now only two years old, and the washer sounds like a jet plane. I paid a repairman $90.00 only to be told this is common in this machine. The repair is expensive, and I would be better off buying a new one! I owned a cheap, little GE washer, which cost me $300; ten years, and never had a problem. Now my dream machine turned out to be a piece of crap. I will never buy a Whirlpool again!

Bought a new Whirlpool range in 10/20. In 06/21 the control panel stopped working. Now they say the necessary part will not be available until 10/21! 5 months without a working range! Dont buy Whirlpool--shoddy products and terrible customer service.

My review merely echoes the other 1-star reviews Ive read below, but Im including it anyway. We bought the Whirlpool Cabrio from Lowes in 2013. Two weeks ago, a mere five years after purchase and shortly after our warranty expired, it broke. It kept showing the UL code and took multiple cycles to wash the clothes. Unacceptable. We called the technician; he came out; told us it was the bearing that busted; and quoted us $800 to fix it (I noticed below another customer was quoted $400 for the same issue). We told the technician thanks but no thanks and purchased a $450 Samsung washer. Our family will never purchase any Whirlpool product again. From their customer service to the performance of their machines-- its all very much lacking.

I bought a Whirlpool over the stove microwave. It was to replace a GE that was over nine years old. 40 days after purchase and installation the plastic started chipping and peeling. I contacted Whirlpool customer service and was told that it was a cosmetic problem and my warranty stated that I had thirty days of warranty on cosmetic problems. This was a problem because chipping and cracking didnt happen within 30 days. The chipping and cracking continued to get worse. I again called customer service because the warranty stated that workmanship and bad parts were covered up to one year. I was told that because it was over my stove that this was to be expected. I thought this was a dumb answer because had I known that an over the stove microwave would have problems from cooking I would have installed it in my living room over the television. I called customer service several times. One of the times I called I talked to a representative who actually acted as if she wanted to help me. She suggested sending an e-mail with pictures and gave me an e-mail address. I did this and got no response. I was getting close to the warranty expiration date. I called again and was told that pictures wouldnt work; I would have to pay to have a serviceman come out and write a statement saying that it was not cosmetic. The cracking and chipping is so bad that I cant clean parts of the door because the cloth or sponges catch on the cracks. The door on the GE microwave did not look as bad after nine years of use as the Whirlpool does after 1 year and 8 days of use. I am not the smartest person in the world but I know the difference between poor quality material and workmanship as opposed to cosmetic problems. Im pretty sure that if my wife put her makeup on and pieces of her face started cracking and falling off she wouldnt want to hear that it is not a real problem its only cosmetic. Bottom line is I am very dissatisfied with the poor customer service and warranty problems I have experienced. I will not buy another Whirlpool product and would strongly suggest to others to buy any brand but Whirlpool.

This unit was new 11/11. Very little oven use but the 1st time the self clean feature was used the outer oven door shattered and now 5 years later there are no replacement parts available. Bought an extended warranty and no results from vendor other than refund $$ on what is left of warranty. Original cost $3200, now useless p.o.s. I will never buy a product manufactured by Whirlpool and hope they go out of business. Bitter... You damn right...

The agitation is too loud. I called Whirlpool customer service and said I wanted to return the washing machine because it was so noisy. Whirlpool customer service agreed that it was noisy and said they would send a technician out. Whirlpool customer service never told me the technician they were sending would cost me 25% of the washing machine cost. The technician said this is normal all machines are this loud. Now I am out the cost of the washing machine plus the cost of the technician and all I have is a very noisy washing machine. Im a real satisfied customer. The machine was bought 12 days ago.

The microwave was easy to install above the stove and it has the exhaust fan conveniently hidden out of site underneath it. The cost was very low and it is not complicated to set up and use. I also like the fact of not having countertop space taken up by having the microwave sitting on it.

Bought a new oven for my new kitchen. Two weeks after install, I had to have it repaired. Less than 6 mos. later, it is being repaired again, for the same problem. Whirlpools policy is to fix it till the warranty runs out, then not their problem. Buyer beware, and if you do buy, make sure you get the extended warranty.

I love my ceramic top. My only complaint is I wish my knobs were on the front of the stove because I am short. It would be nice to not have to reach over hot burners just to turn the temp up or down.

I purchased this stove online and have been very happy with the features. I am able to use alternate settings based on the size of the Pan/pot. Cook timer, light, variable rack displays, etc. The only negative feedback is the need to add 5-10 minutes more to the temperature, based on the recommended cooking time of your recipe.

I bought a Whirpool side by side model GSF26C5EXW00 on 4/24 from Lowes in Buford, It was delivered the next day.We followed all the start up directions. You know what a mildewy moldy towel smells like...Well that is what the water and ice smells and taste like coming out of the dispenser. I have had the technician to my house 6 times. the tap water taste good, the water coming out of the line leading to the refrigerator is good. Gee is must be something in the refrigerator! How many times do they have to come out before they actually do something about it? Like replace it or give me my money back.

I have never posted a negative product review but must do so now. The refrigerator is 1 1/2 years old at most and has been well taken care of. I noticed today that the finish at either side of the bottom of each refrigerator door handle has a problem. I couldnt tell if the finish was pitting or is just discolored. I called customer service and expected that they would help, especially since we have an extended warranty. Representative number one told me that the extended warranty only covers problems that affect the function of the product. I spoke to her supervisor and then her supervisor. I got plenty of apologies but no support. I offered to send pictures, but they were not even interested in checking out the problem.After speaking to them, I took the handle off and I see now that the handle cut into some sort of film that exists on the metal. (I am not talking about the protective plastic coating that is on the the refrigerator at delivery.) The film is lifting off the surface and creating discoloration. If Whirlpool was at all concerned, I think this issue could be fixed with some sort of gasket to keep the metal handle from cutting into the surface. Im hoping the problem is static, but hard to say what will happen. If they had been interested in trying to understand the cause of the problem, it would have been easier to accept the limitations of the warranty. It would have demonstrated an interest in avoiding this problem for other consumers in the future. My last Whirlpool product. Period. Good luck if you decide to do business with them.

Ive had my Whirlpool Gold for over a decade and absolutely love the quality and performance of the unit. No maintenance issues whatsoever throughout the years. I recommend this washer to everyone I know and continue to enjoy the performance and reliability of Whirlpool. I will continue to buy this brand every time as needed.

Purchased a larger hot water heater after reviewing the offerings from the big box stores. Obtained a 40 gallon Lo-Nox type. No problem. Found that I did not have time to install and 3 months later had a company install for almost $300. Within the first month the pilot went out at least 5 times. Had the install company come out and take care of the problem. Worked OK for 2 months and now the pilot light goes out again. Watched the flames myself and find them to be yellow. OK, so try to see what the situation is, call the installer, then call technical support. I am in a basement, on a cell phone and the representative basically has zero patience, zero tolerance for questions, treats me like an idiot and probably has never looked at any of the guides but keeps harping on me.I asked 5 times for patience and guidance not to be treated like an idiot. As time went on it was clear that the representative has zero experience in front of the product or the information in the install guides. She kept calling it a manual and I tried at least 3 times to ensure that her manual is the install guide. She never did affirm. I stated I wanted my money back and she stated no. Whirlpool has a very skillful representative to keep consumers away.However this consumer is a small apt owner that purchases appliances, as well as hot water tanks microwaves etc. No longer will I purchase anything Whirlpool. Oh I will send a complaint about this rep, and she said thats fine send it to the PO box Total lack of product knowledge and not even skillful in a conversation asking for assistance. The installer also stated that this product has horrible reviews. I wish I had seen them before all of this. Total frustration and something unwarranted. I am out $900 and am replacing the tank with a Bradford white from the plumber. Lesson learned. Good bye Whirlpool, hope others stay away from Whirlpool everything. Choosing another brand is the only thing that makes businesses wake up and smell the money.

I like the dishwasher. It cleans pretty well. Some time it soap doesnt open and the dishes don’t get cleaned. But when it’s working good the dishes get cleaned very well.

Since buying a Whirlpool Cabrio washer about 3 years ago have had several breakdowns. Within 6 months the computer completely failed. Since then it failed again. About every six months it costs me around $125 to get it running. The thing is a piece of junk. If the load is slightly unbalanced it just shuts down during the spin cycle. The old Maytag we had ran for over 25 years with the belt replaced once. No other problems. Will not buy another Whirlpool again.

My refrigerator is about 7 years old. Has performed great. Good use of room inside. Easy to clean. Bought only Whirlpool products for years however since the last purchase of a range a couple years ago the quality was greatly diminished. May be changing brands now.

I bought the Whirlpool mini frig from Target 3 years ago thinking it was made by whirlpool in USA!!!! 1) not really made by whirlpool!! Made by Glantz from China. Common deception of USA and Chinese mfg to fool consumers is to license a well knownBrand to glantz in china. Glantz mfg almost all mini frigs under dozens of well known brands. Federal Trade Commission should ban this kind of deceptive marketing. Complain to the FTC Wash DC!!! 2) Chinese mfg gantz mfg defects and how I fixed them: A) back of freezer compartment open, freezer does not freeze B) 45f inside not 40f!!! C) defective thermostat remedies: 1) aluminum foil to seal back freezer 2) weather stripping around door to bring temp from f45 to 40f.D) used Youtube video to adjust defective thermostat, until I can find a replacement thermostat!!! Dys videos: watch youtube repair videos before you trash your frig. 2) check the country of origin, if its made in china, it will not last very long!! 3) buy an extended warranty for any chinese product. You can buy generic frig replacement parts on eBay!!Yes chinese products are cheap, but they do not last!!! One good thing!!! This is a very quiet frig.

Bought new from menards. Doesnt work properly, doesnt wash right and cleans poorly. It too bad because I thought I was upgrading from my old Whirlpool washer that was 15 years old so I order the new cogs for the agitator on the old machine and now using it again. Works better than the new one. Sad that whirlpool wont stand behind the product. Might as well be made in china.

The tub mounts of my 6 years old Whirlpool washer are broken. It’s too expensive to replace. Seems like built in obsolescence! Ive also had mold/odor issues. Finally, I know how to fix that, now this. I just want to warn others, these machines are not designed for the long haul.

I was doing a routine refrigerator cleaning and the glass I was cleaning absolutely shattered all over my kitchen. Shards of glass are everywhere including my disposal. I called Whirlpool and talked to a customer service rep. Of course, this is not under warranty. So I asked to speak with a supervisor. All I could get from her is Sorry, youre disappointed. We can replace that part for $87.71. It has taken me over two hours to clean up all the glass. I wouldnt be upset if I had mishandled the glass, but it broke when I was drying it with a towel! I’m wondering if anyone elses glass shattered in the same fashion.

Purchased Whirlpool Cabrio top loading washing machine yesterday. When wash load is finished (dark load) white marks are visible on the clothing. It appears to be laundry detergent that has not dissolved. I am not happy with this washer and will be returning it.

I purchased a top load Whirlpool washer from Lowes 2-8-12. It got so it wouldnt rinse. When it came to that cycle, it just skipped it and went directly to spin. I dont know how long it was doing this before I caught it. A repairman came out said I would need the equivalent of a motherboard that would cost $330.00. Needless to say, couldnt afford that amount for repair. So I purchased a very nice used Amana for $100.00. I always thought Whirlpool was a top of the line product. This has changed my mind. If it wont last any longer than 5 years I dont want it. There are just the two of us and we are retired so the machine was not overused. I am so disappointed and angry about this.

Bought a Whirlpool dishwasher about 2 years ago. Used it once a day for one year. The bushings already need replacing (maybe $3 to make) and it’s $270 for the part or $280 for whole motor. Do the math. Not impressed.

I purchased the Cabrio washer about 2 years ago. This summer, I began to hear a roar in my washer when it was spinning. I called a repairman and in order to fix it, the tub has to be replaced and it will cost $258 plus service call. My sister purchased her Cabrio 3 years ago and her washer has the same problem. This sounds like a recall issue to me. I think Whirlpool needs to recall this washer or pay my bill.

Whirlpool Cabrio Washer WTW7340XW sounds like a small jet during spin cycle. The Whirlpool Cabrio Washers have a very well known and well documented problem with the tub bearings failing. Many many disgruntled owners have posted their complaints online, and there are many videos showing the issue on youtube. This issue is so prevalent that the manufacturer has created a tub bearing failure repair kit for $350. The repair is so expensive and labor intensive that many of the certified Whirlpool repair shops no longer work on the Cabrio washer stating that a better washer can be purchased for the cost of this repair.That said, the manufacturers customer service group denies that the Cabrio tub bearing failures is a common problem and are quick to state that Whirlpool holds no liability for this problem. Ramping the complaint up to a customer service supervisor is met with the same canned response. Regardless of the thousands of complaints Whirlpool is claiming that it is normal wear and tear for the tub bearings to fail. The manufacturer should recall the units for this manufacturing defect in the Cabrio design.

I just bought a house with a Whirlpool Accubake wall oven and after I did a self-clean, the oven quit working. It goes through the motions of working but neither element heats up. After replacing the elements ($95), I am going to replace the thermal fuse to see if that cures the problem. Whirlpools automated Customer Service phone service sucks. You cant talk to anyone about troubleshooting any problems so you spend money until you eliminate all possibilities.

Ive owned this Whirlpool, bottom freezer refrigerator for two and a half years now. About a year ago I began to notice water on the floor in front of it. I had the ice maker hooked up, which I never used, so I disconnected that. The problem continued. I discovered that the bottom of the freezer compartment would fill with ice and once full the next dose of water would flood the surrounding floor. I have cleared the ice out, on a weekly basis, but have still had the water flow onto my floor. Its a daily thing now as Ive gotten tired of pulling the unit out and removing the ice build-up on a weekly basis. My replacement refrigerator will not likely be a Whirlpool of any model.

After the pilot light on my water heater would no longer stay lit, I contacted the Whirlpool technical support number listed on the unit only to be told my unit was still under warranty, but I would be responsible to pay a $65 diagnostic fee and any labor associated with a repair. The technician came and said my ventilation system was the problem and didnt even touch the unit. He then sent a report to Whirlpool that the unit was flooded which voided my warranty. He did not submit photos to substantiate his water damage claim and now Im being told the unit is unsafe and must be replaced at my expense. This all sounds like collusion to not honor the warranty! I will never purchase a Whirlpool product again!

We made a major appliance purchases on July 1, 2010 of a Front Loading Washer and Stackable Dryer. The dryer required servicing at 11 months with was was covered but it required a major service for a broken motor control board. This has nothing to do with regular usage. The cost to repair is over half the total cost of the appliance.This is unacceptable on a 15-month old washer. Whirlpool would not stand behind their product or service. I had to purchase their Repair Plus 1 program to get it fixed. What a racket!

Very reliable and cleans clothes very well. I have used almost every machine on the market, and none compare. Very quiet and I use very little detergent and CLOTHES come out very clean every time. I am just very satisfied with my experience.

I purchased Whirlpool washer in Dec.2017 and used it in winter months only (Nov to March). It kept leaking and had to get appliance repair service for $50 and was told that machine is defective and whirlpool should repair it or replace it. I phoned whirlpool and they told me I have to use their appliance repair shop to evaluate the machine for cost of $130. The inlet valve was leaking and needed replacement for a cost of $253.55 and whirlpool shirked all and any responsibility. Dont buy whirlpool as it is not a good product and service is poor.

My father and I both got the Whirlpool Gold gas furnace 3 seasons ago. I can't tell you how happy we both are! Our heating bills plummeted; the unit is quiet and does a fantastic job. I am 50 and I have to admit this is in the top 5 of the best purchases I ever made. For me to take the time to find a place to write a review 3 years later should be testament to how happy I am. Make sure you have it professionally installed! Don't skimp here…this is the key!

Microwave didnt even last 2 years. I bought all new Whirlpool Appliances less than 2 years ago & they were not cheap! The microwave wont work until the light comes on inside. Well for some reason now it takes almost 10 minutes for the light to come on & I have to leave the door open until then. Now today I cant shut it because the light wont shut off & if I try to shut it the fans runs constantly. So frustrating as they dont stand behind any of their products! I will never ever purchase anything Whirlpool again.

Last week dishwasher leaked. Set up repair with our local gas company that has service plus. Came today. Repairman showed me there is a hole in the bottom of the tub. Upon closer inspection it looks like the manufacturer drilled a hole that wasnt needed so they routed out a depression in the tub and must have put in some sort of plug or filler of some kind which now came out. I called Whirlpool and explained to lady about the defective tub. She said well if it had a plug of some sort put into the tub it would have fallen out before this. I said Well it didnt it just must have happened as it never leaked before. She said it is no longer in warranty. I told her this is a defect to me as if you drill a hole in the tub that wasnt necessary and then the plug failed that you put in to hide the extra hole. It is a defect not a warranty issue. Upshot is she wouldnt do anything about it. I told her I have always bought Whirlpool but if this is their policy its the last time I buy anything made by Whirlpool. After reading all the complaints registered here about Whirlpool I guess I am more than fortunate as my dishwasher (bought in 2006) had run great until their plug fell out (Great except for all the rinse aid that has leaked out for several years.).

It goes off balance, frequently. It is moldy and stinky. I wipe it out, use a cleaner and leave the door open, but it still stinks. I am getting rid of it and buying a Speed Queen top loader. I am extremely disappointed in the front loader Whirlpool.

I have a 2 year old Whirlpool refrigerator with french door refrigerator on top & freezer on the bottom. I am now spending almost $700 to have a new compressor put in because Whirlpool wont back their products.

In the last 6 years I have had two refrigerators each lasting three years with major repairs from day 1. I am on my 6th repair for my Whirlpool Model WRF89SDAM02 purchased in October of 2013. WHAT A PIECE OF JUNK.

After months of careful research and comparison, I finally bought a pricey (over $2K) Whirlpool refrigerator with a bottom freezer and French doors with water dispenser on top. I really did not want any fancy features, just narrow doors because of my small kitchen, and a fridge on top because of my back pain. Since the date of purchase in May, 2014, I have had 4 service calls. The first was covered under warranty, but no cause of the sheet of ice collection and underside water leakage was identified; I did, however, receive a somewhat patronizing lecture on the importance of thorough reading and comprehension of the owners manual, and a statement that most of my service calls are for customer education. A follow-up service call, a few weeks later and also covered under warranty, identified the cause of the ice collection and water leakage: a faulty duck bill little piece of plastic in the drainage system that is a problem well known to Whirlpool. In mid-June of 2015, the ice maker had to be replaced, to the tune of $360.00. Today, I had a service call ($103.00) and received an estimate of $405.50 to replace the broken freezer drawer slides, which prevent the freezer drawer from fully closing. I will be applying that $405.50 to the purchase of the simplest model, non-Whirlpool refrigerator available, and have the Whirlpool hauled away. Besides the problems noted above, the center of the refrigerator freezes the food, while the freezer compartment arbitrarily defrosts. There are alarm icons that go from blue to red to alert you of the need to replace the (expensive) ice and water filter, refrigerator air filter and crisper freshener. Alarm bells ring to inform you that the doors have been open too long, but nothing alerts you to the fact that the freezer door is not completely shut, or that the freezer has gone into defrost mode because someone inadvertently brushed up against the control panel and changed the settings, or that water is pouring freely out from underneath the appliance. I have had to change my buying habits because fridge holds at least 15% less food, even though it is the same cubic footage as my previous (top freezer) one. Freezer contents easily slip down behind the top freezer drawer and jam the door open. I have to take most frozen boxed items out of their original containers and pack them flat in freezer bags to get enough storage. Some tall bottles do not fit anywhere in the refrigerator compartment, and have to get put in sideways. Even in the absence of mechanical problems, using this refrigerator is like packing and unpacking a suitcase many times a day. While Whirlpool customer service personnel were not overtly rude, there were dismissive and condescending overtones in some of the questions and directives I received from them, and another insinuation that service calls would not be covered under warranty if they end up being for the purpose of customer education. The extended wait (7+ days) for appointments with a Whirlpool-certified appliance repair company, along with the customer education exclusion, were absolute deterrents to the purchase of the extended warranty. Besides my personal disappointment and disgust with the purchase of this appliance, I am sad to see that the Whirlpool brand has slipped so far in product design, quality and customer support.

NOT Even a 1 STAR!!! We spent A LOT of money on a Whirlpool Smart wall oven combo. It has only been installed for about 2 hrs. My husband and I have been trying to figure out why all the features on the Whirlpool app aren’t working. Most of our home has smart features and is connected to our phones so it’s not the fact that we aren’t tech savvy. I finally gave up and decided I’ll call customer service line about it tomorrow when they open. It’s Sunday night so every number we call says it’s outside of business hrs. Then excited to turn on the oven for the first time I turn the oven on and the noise that the fan is making is so loud you can’t even talk over it. The oven has been off for 15 min now but the noise continues. 3000.00 for a huge disappointment. Not to mention the thing is HEAVY. So the thought of us having to remove it and replace it with another does NOT make us happy at all. Best Buy or Whirlpool WILL be the ones doing that. For the trouble and money spent that’s the least they can do. Also family is coming into town for the holiday. We made sure to purchase way ahead of time to be sure we had it, installed it and can use it a few times to get the new smell out of it. Very very upset, angry and disappointed. Now it’s been 10 more minutes and the loud broken fan still won’t even turn off. Now we have to shut it off at the breaker. At this point I don’t think we will be even exchanging it for the same product. I knew we should have bought a Samsung!

I have had my refrigerator for a few years now. When I first purchased it, it was because of the brand and the looks. As far as performance it runs just as good as any other less expensive ones.

We purchased a Whirlpool over the range microwave WH32L19AS1 just over a year ago. {No we didnt buy the extended warranty.} We were reheating some food in the microwave at noon the other day and the microwave made very loud bang and started to hum really strange. We have since discovered the Megatron or something like that has gone out. Just parts $150.00. So we decided to trash the broken Whirlpool microwave. We did some googling and discovered that there is big trouble with this product.

I bought a new home from Pulte recently. All of the kitchen appliances were Whirlpool which came with a 1 year warranty. I have had problems with 2 out of the three that were installed. The oven had a faulty control panel. I am still waiting for the replacement from Whirlpool which I am told could be months getting there. The dishwasher they installed, FX1700017, leaks water from the vent at the top of the door. When you open the door after running a load, there is a puddle under the vent from water that is trapped in the vent. The service company that they sent out said it is a design flaw and there is no fix for it.Whirlpool just keeps saying since there arent any error codes coming up, there isnt a problem with the way the dishwasher is functioning. I was told I could pay for another opinion, but they wouldnt guarantee to reimburse me if they couldnt prove the dishwasher wasnt functioning properly. I guess they dont consider someone slipping and falling because they didnt see the puddle before it got cleaned up a problem. I have given up trying to get anywhere with Whirlpool. I will take my $150.00 for a second opinion and the $200.00 that they want for an extended warranty and put it toward a dishwasher that doesnt leak! Beware!!

I bought a Whirlpool washing machine, model WTW4855HW, and was I ever shocked at how noisy it was. The wash cycle had a grinding noise that was just too much. After 2 loads I sent it back and didnt regret having to pay the restocking fee. I just couldnt believe that with all the technology we have today, that they couldnt build a quiet machine. Im an engineer so I know there are methods through gearing, belts, soundproofing, etc, to produce a quiet machine. Remember the dishwasher of days gone by. You couldnt watch TV with the dishwasher going. Nowadays, you can stand in the kitchen and have a nice conversation with it running. The technology exists. As a matter of a fact, my old Maytag that finally went bad after 10 years was fairly quiet. So, if you dont have your washing machine in the garage or basement room where you can close the door, dont buy this machine! Bruce in Portland