Purchased this Dishwasher on Feb. 28, 2015. In June 2016 about a 2 by 3 inch section of the enamel face on the door rusted and fell off above the air vent. After three hours of hold time between Lowes (with the extended warranty) and Whirlpool (their warranty department) it was determined that this was not covered by either warranty as it was beyond the date of the 1-year mfg warranty and was not covered by the extended warranty (it was only a cosmetic issue). As these calls took place over a matter of 2 days, it was interesting that between day 1 and day 2, Whirlpool had issued a statement that no rust repairs would be covered under any warranty repair - regardless, unless it affects the functionality of the dishwasher. In other words, they KNOW this is an issue with this model and are doing nothing to fix the problem. I must say that the folks at Lowes were most helpful; cannot say the same for the folks at Whirlpool. I do not think I will trust their products again.

My washer is nearly 7 yrs. old. It has almost been a full-time spectator sport. Good thing its in the kitchen! Twists sheets so badly - on sheets setting - that it stops and I must undo the balloon its formed and rearrange the wet, heavy 2 sheets and 2 pillow cases. Now, it cant even finish the clean washer cycle without stopping. It seems it doesnt use enough water to do the job of washing items thoroughly. And it balks at heavy loads - which is what we bought this washer to do - blankets, rugs, quilts, etc. Two people, now only one, and two small dogs. I should have at least 10 years of service from that purchase. Repairman says $300+, and he sees it as a very common code. Build them to last or give up. Im disgusted with Whirlpool now.

It is a top of the line washing machine. I have had it for almost four years. It is the best washing machine I have ever had. I have really enjoyed it, because; I am able to wash my comforters in this washing machine.

This is the second time since I have bought my Whirlpool top loading washing machine, which was January 1, 2011. During a power outage, I was washing clothes and my machine lid would not unlock after our power came back on. I called the warranty service and they made arrangement for a repair man to come out to repair it, but the appointment was in two days. Meanwhile, I had clothes in the machine I needed and was afraid they would become molded and no good. So my husband opened the lid and I removed the clothes. When the repair man came, he was not going to repair the machine because we opened the lid. He was very rude, but after doing some talking he repaired the lid. Now, once again we had a power outage while I was washing clothes and the lid is locked on the washing machine and will not open. This happened Friday, March 16, 2012; my appointment for the repairman to come is Tuesday, March 20, 2012. Meanwhile, my clothes are sitting in the machine wet because we were told not to try to open the lid and wait for the repair service to come. I am very concerned my clothes will be molded and I will be unable to use them. I would never buy another washing machine like this one. Model number is WTW4800X, Standard/Ordinaire VOXr8ENA(3B). Date of purchase: January1, 2011.

I had this same refrigerator in another home and had no issues, this particular one now I have nothing but issues with it. It seems that the quality is not consistent. First the ice maker was not working, then the freezer light burned out and now there is extensive frost build up in the freezer. The refrigerator is only 2 years old!

I have been using this brand for many years. My first washer lasted for 30 years..so I will stick with what I know is reliable. It is a great machine. Very simple. I dont need anything fancy. 3 different cycles to choose from.

Purchased this oven in September 2012. Three months in, we tried to use the self-cleaning feature and blew a thermal link (guessing terminology). Tech came out and got the oven open and that was his determination. Also said he would replace both the front and the rear one because it was pretty common that if one was bad the other would probably follow. Said hed have it within a because he had to order it from the factory. I called a week later because no revisit had been scheduled and found out that the factory also did not have the part and was sending me a new unit. Whirlpool was supposed to call and tell me that and did not. It would be another week. Then a few more days for them to come out and replace it and pick up the original unit.Now I have brand new unit again so we tried the self-cleaner. Same issue. To make a long story short I called again this morning and scheduled yet another service call because the oven is inoperable again after running the self-cleaner. This is the 4th time with the replacement oven. They have replaced the thermal units several times and have replaced the fan.Fortunately, when I complained vehemently about the original unit, Whirlpool gave me a one year extended warranty on the replacement so I am still under warranty, which, if youre dumb enough to buy a Whirlpool after reading this, I would advise paying for. If you already have one and are having similar issues, call Whirlpool and insist they give you one for free because they sell junk.This time I told the nice customer service lady that, since the holidays are over and I can get by without the oven, I am going to run the self-clean right after the tech leaves. When it blows and gets repaired again I am going to repeat the process until they refund my money or send me something that works. Whirlpool apparently doesnt care because in their agreement with their service companies they only have to pay for the first visit. After that they just supply parts. I will keep doing this until I run out of service companies in Denver. Then I am going to pay for another extended warranty when this one ends in September 2014 and continue the process.Wake up Whirlpool!! If these units fail consistently at high altitudes (which every tech that has come out here has mentioned as an issue) then fix the problem or quit selling it in these areas.

We purchased a Cabrio model WTW6600SB2 washer, it has lasted 4 years, then when the pump went out, we paid $200. To fix it then on the 2nd load, it went out, now the tech man says the motor is cracked and Im not sure if the motor is replaced, it will even work. I looked at the motor and it is made of plastic! Can you believe this? Plastic! I didnt believe it until I saw it with my own eyes. I will never purchase a Whirlpool appliance again nor will any of my relatives or friends if they ever ask my opinion.

I bought a Whirlpool duet washer and dryer. These appliances are still under one-year warrantee. My washing machine was broken for four weeks, and they have been unable to receive all of the parts needed to repair it. They have made three appointments to fix the machine, telling me that they have the parts and only to cancel the appointment the night before. I have tried to get Pacific Sales to exchange the broken machine, but they will not do that or compensate in any way. This is a top of the line model; I would have been better off with a low-priced model, and I might actually have a machine that worked. Whirlpool supposedly had the parts on back order, which is not what Whirlpool informed me when I was able to reach them.

About 29 Nov 2011, I bought a Whirlpool microwave, which model no. is magic cook 206 (mech). Sr No. CNF103400315, when we bought this item, we asked for the start up kit, but at that time they said that in grill microwave we dont provide start up kit but after a month when I again raise for start up kit, that time they give but in start up kit some item is missing and the sealed is open. So I kindly request you to take some action to the shop.

I have Whirlpool Washing Machine bought at end of 2012. In 2014, I faced an issue where the washing machine board ics are gone. The services people came and check the replaced a board. It was cost me 6000 Rupees including the service cost. Very next year 2015, again the same issue. Board of the washing machine gone. Now I have to change the board. It seems it may cost more than previous one.I heard that these service engineers are taking the previous my board / replaced board. They are repairing it and sold it again and again so the quality of the board is question mark. As a customer I / we cannot spend money and change board every year. I just want everyone to think twice before you go to Whirlpool Washing Machine & its products. I had a same kind of poor quality issue with even water purifier too. Consequences - I have spent Rs. 10000 already, it is loss for me beside the buying cost of the products.

Washing clothes is a nightmare. I am constantly removing clothing from the washing machine that have been torn and left with holes. I am utterly frustrated. Because the machine is more than three years old, there has been no solution to my problem. I have now replaced clothing items in excess of $2,000. I am always here that they will send a repairman and yet there is still the problem. This machine is costing me too much money. The newer machines have fixed the problem. There is no gap between the drum and the doorway or rubber piece. I want that piece to stop this nightmare. This machine has taken a dream of mine and demolished the experience. I hate washing clothes but more so having a machine at home and then going to the laundromat to stop the chaos with doing laundry at home.

We are so disappointed in the purchase of this machine! It doesnt put enough water in the machine to clean the clothes, and the spin cycle has continuously gotten louder and louder to the point I think its going to explode when it spins! Is there any recourse we have or any recalls on this machine?? Thank you for your help!!!

We had Lowes install a Whirlpool model Nu40T121-403 natural gas water heater early October 2012. The temp controller went out in October of 2014. I replaced the controller myself at a cost of $30 for overnight UPS from the manufacturer, American Water Heater. The controller went out again almost exactly one year later and I again replaced it for the $30 shipping charge. In both instances the customer service person told me the malfunction was probably due to my not flushing the heater annually, causing a sediment buildup. The water to the heater not only flushed annually, but is filtered through a water softener and there was absolutely no evidence of sediment in the drain water or on the part of the control that is in the tank. Now it has stopped working a third time. I called Lowes about replacing it, but they only carry Whirlpool, so wont be buying a replacement from them.

First time owner of a Whirlpool range and will be the last time. Nothing but junk! I liked how the top grates were and electronic ignition. The knobs turn too easy and often when bumped will turn gas on without igniting. Very dangerous. The oven grates guides rusted almost immediately making it difficult to pull racks out. The oven light works sometimes. The glass on the oven door at the bottom came unglued. The bottom door under oven is a total waste. No use for it. In my adult life I have had different brands but this is the absolute worst and will never recommend this brand to anyone period.

Within 5 years, this is my experience: A broken brand new Whirlpool fridge after 6 months of purchase; a broken oven that needed repair after 1 year, and today, the oven door just shattered in pieces after I heard a loud noise from the kitchen, almost injured the kids. And guess what, I just returned a new Tilt-Head Stand Mixer KitchenAid that wouldnt stay in place; the head keeps on tilting and would not stay locked. After being on hold on the phone for almost 3 weeks for a return, I found out it was a Whirlpool brand family. This is horrible, I would suggest to never buy the Whirlpool brand; their products are a real nightmare and their customer service is not reliable. If you do buy from them, expect unreliable products and very long long wait periods on the phone.

I have had this refrigerator for 23 months. The ice maker has been a continual problem. It overfills and water runs onto my hardwood floor. After four service calls for the ice maker, the defroster heater caught on fire and melted the interior wall of the freezer. Not sure if we fixed the ice maker since we had the fire four days after the last service call. My service rep declared the refrigerator unrepairable. Fortunately I had purchased an extended warranty and they refunded 85% of the purchase price after 2 years of use. Besides the ice maker problem and the fire, I also had trouble with food freezing in the refrigerator compartment. I dont recommend this model, but my repairman says that Whirlpool is as good as it gets.

Whirlpool Cabrio WTW8500DW0. Like: Top loading, Handsome appearance, clear glass lid, easy access soap dispenser plus separate Oxi dispenser. Dislike: Does not have a soak cycle. We didnt realize until after we replaced our old Sears Calypso what a really poor job it was doing. It damaged the clothes and never really got them clean. Also, the small capacity made it nearly impossible to wash large items such as bedspreads or comforters. The Whirlpool Cabrio WTW8500 has be a delight.

We purchased the Whirlpool Cabrio washing machine around January 2006, and from the start weve had nothing but problems with this appliance. Within the first year, water was leaking under the washer which was coming from a crack in the plastic housing of the water pump. I replaced the pump myself to save on labor. No big deal. The very next year, I started getting the F51 code and there was no way for me to get around calling a service company to have it repaired. $350 and one circuit board later, it was repaired. It remained working without fail until recently when it began giving the same F51 code. Let me guess, another $350 for better repair? I have to assume that the new circuit board that was installed wasnt any better than the original one that was replaced. I wouldnt put another $1 into this hunk of junk and Whirlpool should be ashamed to have this product on the market. I will never buy another Whirlpool product.

We have purchased 4 refrigerators in the past 20 years. The first three were not Whirlpool and were a constant issue for us. Once we purchased the Whirlpool, we no longer had issues. We have the side by side with a freezer at the bottom. This model has performed exceptionally well for us and hasnt presented any issues for us. I would highly recommend it to family and friends, thus the rating of a five.

Bought this refrigerator in 2018 and ice maker went out 2x, then compressor went out and waited 4 weeks for part. Now the refrigerator is broken again and not cooling. Dozens of other reviews indicate the same issue with this model. It’s clearly a defective model. Customer service in Tennessee are very friendly but my refrigerator is still not working. Whirlpool French door - wrf954cihm.

I purchased a front loading Whirlpool washing machine March 2017. I have need to have the drain pump replaced and the motherboard replaced. Each repair took 30 to 45 days to get parts and service. I would not recommend the washing machine.

The oven has not worked correctly from day one. I have to use a thermometer plus after the correct temp is indicated I still have to wait another 15 minutes for the oven to reach the desired temp. Also have to set the temp for 25 degrees higher than the one I want. The burner that supposedly has two sizes in one is basically useless. Temps are not correct and sizes are misleading. There is a tiny groove around the outside edge of the stove top that gathers crumbs which are hard to clean out.

The washer can not spin dry, as the unit will not balance. When it spins, it will get out of balance, and shuts off. I have had a repairman out, but he said he can not fix it, and that this is common with your units, He suggested we get a new one, but not from Whirlpool.

I had purchased fully automatic top loaded WHIRLPOOL WM 360 BW PRO-HS 9.5 on 08/05/2019. I had purchased the above machine after going through the various claims made on the website. However, I regret to say that since installation I find that the performance of the machine is not up to my satisfaction. Even after two visits by the engineer, the following issues remain:(i) The machine makes lot of noise in the initial stage.(ii) Though the timer shows a particular time during selection of a washing cycle, in reality the machine takes one and half times more than the timing shown. In case one selects warm / hot water, the actual time taken is twice that shown or more. I am sure in winters it will take more time in case warm / hot water is selected.(iii) The clothes get badly entangled during wash.In the past I had a LG front loading washing machine which never gave me any problem. I had gone for the best top loading model of Whirlpool hoping for better performance but it has only caused problems. Not worth the expenditure.

I am writing this complaint because of the very poor service of Whirlpool. My washing machine broke after 1 year of use. Luckily, I was on my 2-year insurance. The wiring fully collapsed and I needed to change the whole drum. I called Whirlpools customer service and they said that they would fix the problem after 2 weeks. They came on the day and found out the problem and ordered a new drum. They said they would fix it up on the 5th of December, and it has already been over 3 weeks. On the 4th of December, Whirlpool called me and said that the item they had ordered for me has been damaged. I am not satisfied by these products because it is only a drum (it cant break that easily). I cannot recommend this company to my friends and family due to the quality of the products and the poor customer service as I was waiting on the phone for almost an hour trying to get through.

I purchased a Whirlpool bottom freezer refrigerator for my wifes birthday because my old one was old, ugly, rusted and didnt match. Since she likes to cook, it was her dream in life to have a stainless steel refrigerator with a freezer on the bottom. At the time, it was the only kind that would fit into spot. One year ago, first the ice maker leaked causing water to spill onto the floor. Since I am a mechanical whiz I bought the part for about $30 and fixed it myself. We were happy.After two years, the freezer worked, but the refrigerator part went warm. I had a repairman replace the control box for $100. It still didnt work. We called Whirlpool, and they said the warranty expired, but as a courtesy, would charge me $95 for a service call. That was not acceptable. They told my wife that the products were man-made and are prone to mistakes. I replaced the fan myself for $100, but drove a total of two hours to get the part since it was rare. It worked great. For one and a half weeks, we were happy. Then the refrigerator and freezer DIED. Only the light and the fan worked. We bought a old school used GE top freezer, but at least it is stainless steel. We lost $2000 in two years and the people at Whirlpool refuse to do anything about it because it isnt their problem. Worst refrigerator EVER!!! !

ECO friendly top load Whirlpool washing machine - I bought this machine September 2013. Now it has a continuous clicking sound. It appears to be the lid locking mechanism and the washing machine will not turn on. It is under warranty and I am finding it hard to get a repair service in my area that is directed to Whirlpool to come and fix it. The only appliance repair in our area states that they will charge for trip and service if they find that is not a defect within the Whirlpool perimeters. I could be charged up to $200 for trip and service which is half of what I paid for. Whirlpool states this is not the case, and I am now having to wait a week to even set up yet another appointment. I have other machines that lasted 7-10 years until they wore out. I am frustrated and what could be a simple fix has turned into a financial nightmare.

Bought the Whirlpool Duet washing machine. It lasted around eight years. In the meantime I was replacing the rubber door seal cleaning out the pump constantly. The plastic pieces inside the drum all broke. Every few months I would get an error code. And During spin cycle it would literally shake my entire house. The problem with all the front loaders is the construction of the drum and the drum bracket. They are made of dissimilar materials. (Stainless and zinc) When you add soap to the water then the bracket becomes an anode and the drum becomes a cathode, which creates electrolysis which corrodes the bracket. When the bracket breaks your machine is totaled. I’m finished with every manufacture except Speed Queen. I bought a Top loader Speed Queen and I love it, it is built like a tank.

The duet washer is just over one year old and started showing F25 code on screen. It had been making a really loud noise in the spin cycle. Last week, a really loud noise and then the loads wouldnt be spun. There was a puddle of water on the floor near the machine. We had a repairman out today and he stated that theyre repairing these machines all the time. He stated it was the bearing and that theyd been told that Whirlpool had installed bad bearing from a different supplier. I called the Whirlpool experience and after 4 minutes and 19 seconds, I actually spoke with a service rep. She said since my machine is less than one month over the one year warranty, Id have to call the extended warranty people. I asked for a supervisor and after 2 minutes and 38 seconds, she came in line and wouldnt budge from her story. They also stated that there are no service issues with this model washer. Extremely poor attitude and Whirlpool is doing everyone, whoever purchased a duet washer, a terrible job on these washers. At least, Ive now found out that there are a lot of other folks out there with the same problem. We need to get some attorneys to start a class action just like the mold/smell customers did already. Sad, sad day for Whirlpool as Id been a customer all my life.

We have put hundreds of dollars in service calls and parts on these items. I bought them because they were supposed to be good choices. NO way! I have replaced motherboard in washer, belt and sensor in dryer, the washer has had mold in it since week one. Ive tried to clean it but just keep coming back. All my clothes smell like mold and I already have lung problems! Cant afford to buy new right now. But last month my dryer started making terrible banging noise and so repairman says I need another part! I bought the part more money! Just to have it quit again! Now the barrel split! I dont think I should have to pay the money I did for this set and surely shouldnt of had to replace so many things that went wrong or put up with the sewer smell from the washer!

Purchased both Cabrio washer (wtw6200sw2) & dyer brand new in 2007 for $1200. Within 4 years the motherboard went out. Whirlpool didnt want to fix it. They said it was past warranty. After many complaints to corporate, they sent someone out to repair it for $496 (they paid). Repairman said these models had motherboards from Japan & Whirlpool was aware of the many issues, but wouldnt do a recall. 2009, the springs went out, 2011 F codes began to appear. Clothes dont get clean; not enough water. 2014 & 2015 DU & DL codes appear. Now I need a new Lid latch assembly. These washing machines are not worth buying. Never again will I buy another Whirlpool!! My mom had an old Kenmore that lasted 20 years and only needed a replacement belt. No more fancy high end washers for me!

We bought a Whirlpool dishwasher (Ser# F21102027MOD, Model# WDF730PAYB2) after reading some of the reports that it was just as good as a Bosch. Wrong! We bought this washer March 17. On May 17, the selector switch and sub control broke down. We had bought this item at the HH Gregg store here, and also purchased a 5-year warranty which they said we cannot use because the dishwasher is only 2 months old. Is there a lemon law? And what makes this worse is that we called Whirlpool on May 18th. They could not get anyone out here until May 25th to look at it. As of this time, they still could not fix it because the two parts had to be ordered. Today is June 1st and the part is still not in? Makes me think, does this part always go down because its on back order? So you are fully warned, do not purchase a Whirlpool. If I can get some extra money, I am throwing it out and buy a Bosch because I dont think it will ever be fixed.

Do not ever buy a Whirlpool refrigerator. Sloppy construction, bins dont close, doors dont seal well and a brand new fridge doesnt cool to a safe food zone. When we call for service, I got the run around for almost 2 hours. They wont be sending anyone to service a brand new unit for an entire week... And thats 2 days before Thanksgiving! I have never had an appliance made this poorly. We dont have the space for a bigger unit, so thats why we bought this model. Size shouldnt impact quality!

Bought the washer from HH Gregg for over $560 12/2012. Turned on power 4/2014 and just heard clicking noises then nothing. Had to get technician. Paid for $75 service charge and waiting for cost of labor and part for the lid lock/latch assembly. I see a lot of complaints with this new machine. I bought a new one BECAUSE I did not want any problems with repairs. Whirlpool is ripping off the consumer passing out this piece of discombobulated metal, wires and electronics. An appliance like this should last AT LEAST 7 years without a problem. I wish there was a class action lawsuit and will be waiting to the day it surely comes.

I purchased a Whirlpool Cabrio set about 5 1/2 years ago. Almost right away the washer made a horrible banging noise when In use... I had purchased a extended warranty so I had the service man out. He replaced something but the washer never acted right. I just about 2 months ago replaced it with a normal washer costing over half of what the Cabrio cost me... and now just a few days ago the dryer followed suit and died. The repair (out of warranty) was going to cost $150.00 and that was just for the part, I had service people out twice for the dryer since it came home with me also. This set was the biggest waste of money I have sadly wasted in my lifetime, is it just that they make things badly these days or the more crap that a machine has on it the crappier it is???

My machine has been ripping clothes for a few years but I thought, initially, that it was a snap, zipper or hook causing the problem. I recently got fed up and found this: **. It makes it pretty clear that it is a manufacturing defect. I called their customer service centre and spoke to a supervisor that told me it is normal wear and tear and that perhaps the glass in the door had worn out. Yes, thats right, she said maybe the glass has worn out.They are offering ZERO assistance in what would be a $500+ repair for me. Admittedly, my machine is five years old and out of warranty, but to me, when the repair is to install an entirely new style of door so that the clothes no longer get caught underneath, it is a defect. 43 different models of their machines are included in this issue and it was identified in 2012, a year before my machine was made. Why didnt they correct it before that?

We are doing a kitchen remodel and I found the best price here. I was a little skeptical to order a range online, but I did go look at the exact range in the store and decided I would give it a try. I received email updates about the product and during delivery, I received 2 calls.... one to tell me approximately what time the range would be delivered and another when the driver was about 20 minutes away. All around good service.

This aqua clean is garbage. Had Whirlpool with heat clean perfect. Now have to clean my oven with self cleaning over easy off. I am so disappointed. I always thought of Whirlpool as a good choice. And have bought Whirlpool before. But not after this. Bad, real bad.

Whirlpool serviceman came out to see why our brand new dishwasher didnt dry the dishes and left pools of water on glass bottoms. Repairman said all the new dishwashers are like this. The heating elements do not heat hot enough so that the machine gets a higher efficiency rating. He said the solution is to use the dishwasher during the day and at the end of the cycle, open the door so the dishes air dry. My previous 24 year old GE dishwasher did a great job of drying the dishes even when we didnt use the heated dry cycle! The only reason we had to buy a new dishwasher is because we bought a new house. I am very disgusted with the Whirlpool dishwasher. Might as well do dishes by hand.

I live in Florida and in December 2012, purchased a Whirlpool upright freezer from my local Badcocks. About two months after the purchase it started making this weird loud sound. I contacted Whirlpool and they sent a local appliance company technician out to check it. The technician ripped my brand new Linoleum floor when pulling out the freezer. The result was, in his opinion, nothing was wrong with it, that the loud sound was normal. As it continued, another tech came out and his opinion was it needed a new compressor. So, it was replaced and lasted about a month. I was getting something out for dinner and noticed everything in my freezer was unthawed... all that money wasted a freezer full of food gone. So, Whirlpool once again sent the same appliance company out but a different technician. This one said it that he needed to order parts which he did, a different tech came out to install the parts and told us he didnt know what they were for and our freezer didnt need the parts the previous tech ordered. So this tech put dye in the lines and left. The dye leaked out from under my freezer all over the floor which is now stained because of the dye that leaked. This is the brand new floor they had already ripped during the first service call. So, now not only is my floor ripped but stained as well.Once again, about a month later, I find my freezer full of meat unthawed a third time. Once again I called and find out they have dropped the contract with the company that came out the first two times. So they refer me to another local appliance repair, and this new tech says that it needs a new compressor. This will be the second new one in less than 6 months. They order that part and repair the freezer; this fix lasted for about three months this time. On my fourth call to Whirlpool, I expressed my frustration with losing my food and the hassle of an inferior product purchased brand new under warranty. I definitely was not satisfied with the service and the customer service representative could not find my warranty record. He was also very rude and when he finally found my record, he told me I was no longer under Whirlpool warranty. This was wrong as I have my paperwork showing date of purchase AND the four-year extended warranty we purchased as well. I asked him what they would do for me since their inferior appliance and incompetent repair technicians cost me hundreds of dollars of ruined meat and other frozen food. He said they would do nothing except have another repair tech come out. Until the freezer is determined to be unrepairable that is all they can do.So I scheduled the tech to come out the fourth time and he found that some untrained tech had put oil in the line and the lines and compressor has to be replaced and flushed. I have already not had a freezer for a week waiting for tech to come out and now the parts are put on back order for another three weeks. The fourth repair tech called Whirlpool from my home, while I was standing there, and told them that it basically is beyond repair because of the price of parts and labor. He told Whirlpool it would be cheaper to replace the freezer but Whirlpool told the tech to replace the lines and compressor and flush everything out. So three weeks later, he comes back out on 10/13/2013 to make the repairs. I bought this freezer in December 2012 for $1200 and have been dealing with issues on and off since Feb. 2013 and now its 11/29/13 and once again my freezer has stopped working. I have lost all my food because Whirlpool sold me a defective appliance and would not make it right. I have asked them to replace it and they wouldnt. My husband and I have just purchased our second house and we were very excited about the remodel coming up in the kitchen. We were going to purchase stainless steel Whirlpool appliances, but after this company has treated me so badly, I will not buy anything with the Whirlpool name for our stove, dishwasher, microwave and refrigerator.We probably would have spent about $3500 on appliances, but we will purchase a different brand and give our $3500 to a company that will treat me better as a customer .I used to have trust in this company because it is well known for quality products, but I dont trust them anymore. I will advise any of my loved ones and friends not to purchase any Whirlpool appliance because of the inferior quality and lack of interest in making this situation right. I tried for almost a year and gave them 5 opportunities to do the right thing and now Im done. They dont care about the customer and that is a shame because they have lost a valued customer. As of now I have another tech coming Tuesday b/c my freezer is sitting not running again. Model #EV201NZTQ02.

Whirlpool Cabrio washer Model WTW6500WW1 Ser C02670098 Type 580 is the worst appliance I have ever had. All the bad comments from people are all true! The washer leaves clothes wet. I get F1 error code or it just locks up and I have to unplug it and plug in again, twists clothes up and doesnt get clothes clean. I have always bought Whirlpool appliances because they were good but this washer has changed my mind about Whirlpool.

We purchase a Whirlpool washer model # WTW5000DWI, SERIAL #C842 43102 ON 10/30/2019 and it has been nothing but a disappointment. We are senior citizens living on a very limit income with several health problems, and cannot go to a washeteria to wash our clothes. We had a washer that lasted over 19 years and when the motor failed I figured it was more practical to purchase a new washer versus repairing this old one. We had a very reputable Whirlpool dealer here and was very helpful and recommended this washer and the price was in our budget! Was that a big mistake, it does not clean the clothes, does not rinse the clothes with using the 2 rinse cycle and still, does not rinse a load of sheets. I bought a large capacity washer so we could wash 2 sheets at a time. Wrong! You cannot get more than a couple inch of water on the Deepwater cycle, so its like washing clothes on a riverbank on rocks, it rubs clothes together. On my wifes good clothes it will cause little balls of fabrics on them, clothes does not smell clean, and if its real dirty clothes, it will not clean or take the stains out. Its water efficient alright, it does not use any water!Its for sale, and I have talked to a lawyer. Whirlpool customer service was no help at all/All they want was to send a dealer to check it out, the only problem if there is nothing wrong with it that will cost me min. of $125.00. Warranty will cover a manufacturing defect, not a design problem which is what this is. I will just go to small claims courts and get my money back and be done with Whirlpool, hell they dont care! I would buy any washer that is cheaper and has an agitator, without a water efficient features and is top loaded model. It does not pay in this world where large manufacturing companies dont care.

Model #RF262LXSQ Serial #RT2031953 - I purchased this appliance from Lowes approximately 6 years ago. Last week, I was heating soup and about 5 minutes after I placed the pot on the stove on medium, I heard a large pop and then several cracking noises. When I entered my kitchen, I found the burner flaming red, and when I tried to remove the pot, it was stuck. I immediately turned the burner off and after a few minutes, when it began to cool, was able to remove the pot. What I found was the glass top had melted and blistered and was cracked from front to the back of the stove. Although Lowes was not able to help me, they suggested that I contact you as they had never heard of this happening before. Not only am I dissatisfied that a stove should last many years past this purchase, I am inconvenienced until another stove can be delivered. I believe this to be a factory malfunction of the stove and request a credit for my purchase.

I have had this unit less than a year and started having pilot problems. I would just relight and ask family members to take shorter showers or not run the washing machine or dishwasher at the same time. I would have to relight the pilot 3-4 times a year and would just tolerate. Now the water heater fails on a daily basis. In the last four weeks, my wife would say NO HOT WATER AGAIN. I am so tired of dealing with this, so last night, I called Whirlpool and associate was polite but gave me a lot of things that I should do (43 yrs a pipefitter). Before all was said and done, he is shipping me a new gas valve (at my expense) that I will gladly install to get rid of this problem. Will not EVER buy a hot water heater from Whirpool or Lowes ever again. Whirpool should stick to washing machines!

I purchased a washer Type: 587-08, MOD: 1CWTW48004QO, Serial # C21920164 about two years ago. The appearance of the machine is in an excellent condition but its not working. The tub inside is slanted and makes a loud banging sound when rinsing. It is no longer in warranty. All my appliances are Whirlpool brand because my mom has items that are still 15years and over. This machine that I purchased did not even give me a quarter of that. The prices of these items are expensive and increasing all the time but the quality, durability and lifetime is diminishing at a faster rate. I am worried about all the other items I purchased: dryer, refrigerator, stove and microwave. I am most dissatisfied. I STRONGLY believe that this unfair and unlawful....I work hard and save up to buy these items to only get two years from it......Whirlpool please render some assistance!!!

Our new home came with brand new appliances. I love our Whirlpool microwave. Its reliable, quick & has lots of great pre-programmed features to assist with regular. The independent timer is a total bonus too.

After seven long years of one issue after another, about once a year replacing one part after another, draining the unit to replace parts, waking up to cold water, I finally gave up and replaced this Whirlpool water heater, model model # FD1H4040T3ENOV unit. Never to buy a Whirlpool unit again. Thanks for the memories.

It was time to put the old Frigidaire Washer out to pasture. I researched for quite some time online to find just the right new one. Its all so confusing as they all claim to be the best. The Whirlpool WTW500DW Top Load is the one I chose to look at along with 2 comparable others. I have had Whirlpool appliances in the past and was always happy with them, so I will be honest, I was leaning towards Whirlpool. I purchased the WTW500DW and matching Dryer after looking at the 2 others first. Price was lower, features were more to my liking and better quality/sturdiness was very apparent to me. This was the lower priced machine out of the 3 but had everything I wanted and a little more. The HUGE wash basket is wonderful. I have literally cut our laundry down from 4-5 loads a week to 2! Our clothes have truly never been cleaner.I am amazed at the great job this machine does with a minimum amount of time and water. It is quiet, efficient and the cycles do what they are supposed to do. The absence of electronic pad buttons is greatly appreciated. Its standard dials are easy to read and set. In my opinion, Whirlpool has done it again. Its a great Washing Machine at a price that is lower than others without as many nice features, it is well built and does the job perfectly.

We purchased a higher end cabrio model only 3 years ago. Last year, on about every 5th cycle, the load would not spin at the end. Id have to remove all the wet clothes, set it to drain and spin, start it and wait for it to hopefully kick in. When I do it right, it kicks into the spin mode. I had to quickly press start/stop to unlock the hatch and reload the soaking wet clothes and wait for it to spin properly. Yesterday the same thing happened again. This time, it did not kick in. I ended up flipping the washer over and taking a look underneath. I discovered that the motor was seized. It had lost all its lubricating oil and smoked the belt. Now, my 3 year old washer is sitting in the driveway awaiting a trip to the dump since I got fed up and went out and purchased a new Samsung top loader. I emailed and called whirlpool with no luck. Not impressed. When I went out to buy a washer today the first thing I told the salesman was to stick anything with the name whirlpool out in the trash bin out back.

Bought the above named model number Whirlpool dishwasher in Nov 2017 and it stopped cleaning 6 months later, dishes were instead of dry and NOW the motor is completely shot! Never again! This is ridiculous that the part cost more than the product! Worse that I need it repaired or a new one in less than 3 years!

My wife and I bought my mom a Whirlpool Cabrio. It worked fine but after a while it stopped working properly. It would take forever to start washing. We called Lowes and they said it was fine. Second time they came out, they replaced a part that was the problem. Again it didnt work. Would start to wash two to three hours after you hit start. My mom had nothing but problems with it. My wife and I had a Samsung washer and dryer which worked excellent. We sold them when we moved and our apartment had no washer/dryer connection. I should have given them to my mom. So she was tired of her washer and we set out to buy a new one.So since I had a Samsung, I convinced to get one also. We went to the Sears outlet and found a really nice Samsung washer for around $500. So far, the machine has worked well. No complaints and gets the clothes clean. So for anyone that has had problems buying appliances and is looking for a new one, well, Samsung is doing a great job so far.

Bought a water heater on May 5th for 539.00 and was unable to get hot water all the time. After many days and dealing with Lowes which did not help and Whirlpool, I discovered that the unit I bought had no dip tube to bring the cold water to the bottom to be heated and thus provide hot water to the hot water outlet on the heater to the rest of the house. People at Lowes had no dip tubes and really have no knowledge of what is going on as the people at Whirlpool whom I called.

I purchased a 50-Gallon Electric Water heater in 2006, sure it lasted and worked well for quite a few years; however, in August 2014 my power bill started to rise dramatically, I live in Arizona and $300-$400 power bills are the norm in the summer months; however, a $700.00 bill will immediately be noticed. I contacted the power company and they sent a tech over who performed a lengthy diagnostic and determined that my water heater was running constantly thus accounting for the great increase in power, I contacted Whirlpool and received 2 heating elements (no charge) which my pricey plumber replaced.The problem still remained and I contacted Whirlpool again and again trying to get this issue resolved. I paid less than $400.00 for the heater installed and since Ive been having the issue Ive almost paid another $400.00 in labor costs trying to get a resolution. Ive decided to get another system and my only reason for posting this is to inform all that the Whirlpool heaters seem to be very problematic, like others Ive had plumbers decline my business when I inform them that I have a Whirlpool tank with the Energy Smart module.

Have had it replaced. It is not a great value. Need one with freezer on the bottom. Will buy another brand. Not 2 years old making noise and it sounds like someone pounding on the side after the doors are open. This is a side by side fridge and has space but I question when this will go out.

I bought a top of the line Whirlpool front load washing machine (WFW97HEDW0) and drier with my new construction house. After a few months the washing machine began making a loud, banging noise during the spin cycle. Then about a month before the 1 year was up the unit broke and dumped all the water in the drum into the catch pan it was installed on. I called for service and someone showed up in about 3 days. The tech opened the unit and found that the plastic/composite drum the spin unit was contained in split in half all the way around. The tech exclaimed he had never come across this issue and would report in what he found but that he did not have the part and it would most likely be a whole new unit but that its up to whirlpool to make the call. I would find out that whirlpool had decided that the unit can be fixed and they have ordered the part and would call to schedule the repair.A week went by, with no word. I called warranty service company, Via Services, and they tell me that the part is on back order and that it would be two more weeks before it would come in. Now were looking at being without a washing machine for a month. I communicate this to the builder and they somehow get whirlpool to come out a week earlier than they said they could. The day came for the repair and two techs take nearly 8 hours to repair the unit (how is this efficient?).After the repair the unit ran with an odd noise that I attributed to the way it was stacked. A month goes by and two days after the 30 day repair warranty I go to do a load of laundry and the unit turns on but wont run. I called for warranty work because it was clearly not repaired sufficiently. I schedule a tech visit which is for a week after. The day come and the tech says he cant fix the unit without charging me for the repair because it is now out of warranty and if I have the extended warranty then I need to set that up with the extended warranty group. I send him away because I had just paid for the extended warranty. I called whirlpool for the extended warranty work and they schedule a repair contractor to come out in 3 days.The repair contractor calls me directly to confirm if the unit is side by side or stacked. I let them know that the units are stacked and they say they cant repair it because its a two tech job and they dont have enough techs. They send me back to talk to whirlpool. Whirlpool then notifies me that because its stacked I have to either unstack it myself or hire someone to unstack it for me. Well, I cant unstack the unit by myself and why should I have to pay someone to unstack it when thats what the unit was designed for? At this point I am going back and forth with the builder to get a refund so I can replace the unit. I will forever steer clear of any whirlpool or subsidiary products. The products are flimsy and the service is no better.

I bought a Whirlpool gold model #GB2F-1DXW507 / k27711376 when we remodeled our kitchen in October 2012. After a couple months I noticed water on my floor, then in the bottom of the freezer. I called Lowe’s. They sent out a repairman. He said it was a flaw in the design and put the redesigned part in. When they delivered the fridge they changed the door to a left hand open and it was never right. After 2 years the ice maker stopped working. I just started buying ice. Today 5 years and 5 months later they said it will cost me almost $500.00 to fix the electric board and the Ice maker. The fridge stopped working would not get cold. And the certified Whirlpool repairman said it was a very good looking fridge and he would fix it with a 90 day warranty on the genuine Whirlpool parts for almost $500.00. I said I wasnt a idiot. Why would I spend that kind of money for JUNK. After reading some reviews I think Whirlpool knows just what junk they are selling. I called and all they said was, “Thats too bad. We will take it under advisement.” I bought mine 1st then 1 year later my sister and sister-in-law bought theirs. 3 fridges with all the same leaking issues. I hope they dont end up with all the same problems.

Purchased a new Whirlpool water heater from Lowes. Two days into the reset switch kept tripping, Whirlpool wanted me to wait for someone to repair it. Lowes exchanged it for me. When I called Whirlpool service myself, Jessie was in technical support could have careless about my business and was dismissive about any issues or concerns I was having. This will be my last Whirlpool product ever.

In July I purchased a Whirlpool Gold oven and cooktop from Lowe’s. It was delivered in Aug. after a 5 wk wait, since it had to be ordered. Since installation, the hot surface light on the cooktop stays on. I called in & was told to try resetting the elec. breaker. Did that... still stays on. Model G7CE3034XB00, Serial D43005649. On Sept. 4th I called & spoke to Carrie (I believe in TN) who told me she would try to find a service tech in my area & would get back to me in 3-5 days. Apx. 5 days later she called & left a message on my cell phone stating that she could not locate a service tech in my area. I would need to find my own service tech & submit any invoices to the resource dept for reimbursement. Parts could be ordered at no charge. I have nothing in writing from the company to confirm I would be reimbursed, nor was I told how to correspond with the resource dept in the event I had an invoice to submit for reimbursement.Today, Sept. 18th, 2014, I called Whirlpool again (800-253-1301) & talked to Stephanie in Michigan. She told me the same info. When I asked to be sent a wiring schematic I was told I didnt need one. When I asked how to get in touch with the resource dept. I was given a fax no. & email acct. When I asked how I was supposed to get in touch if I didnt have either, she said I should go to the local library. Now lets imagine for a moment that I am disabled or live so far out in the country that I cannot get to the library... How am I supposed to get to a fax or email acct. Has anyone at Whirlpool considered that? This is a new appliance under full warranty, yet it has become my job to find a service tech, pay up front, & wait for reimbursement. REALLY??? I am also in the market for a new dishwasher & you can bet it wont be a Whirlpool!

Whirlpool is an awesome fridge. There was plenty of room for everything. I loved the freezer part too. I would love to have another one because mine was in a fire in 2015. You will like Whirlpool.

We had the unfortunate experience of purchasing a Whirlpool product from Lowes. During Memorial Day weekend we came home to a freezer full of defrosted meat. After having to throw away 1/3 of a steer that we purchased from a local 4-H students project due to the temperature of the meat and not knowing how long it had been at that temperature. I called Lowes and they said there was nothing they could do for me since the freezer was over 1 month old. It was right at 2 months. (Purchase date - failure date). They advised me to call Whirlpool directly and gave me a number to the warranty technician. The warranty technician came and immediately found the problem. The defrosting connector was not plugged in when it was manufactured. Clearly a manufacturer issue. I called Whirlpool to find out how much of my over $1500 of meat they would cover. They told me they would not cover any of the loss. Then they offered me a 1 year extended warranty for free for my Inconvenience. What a slap in the face. Why would I need a warranty or even a freezer for that matter since I no longer have anything to put in it. Needless to say I will no longer purchase any products from Lowes or Whirlpool.

It was horrible! I paid $568 for a Whirlpool dishwasher from Lowes in 3/09. The Clean light flashed, then stopped and flashed again. I didnt buy an extended warranty, because I felt Whirlpool was a great company. I had A&E Factory Service come for a service call, paying $70 later w/ tax, only to find out that the heater is no longer working. It would cost $216 to fix it, and we had to remove the dishwasher. Why bother for the total of Todays service call and the repair, when I could buy a new dishwasher? It cost $568, and it lasted a little over 2 years! It was horrible. Theres no warranty and no help from Whirlpool, because I didnt buy a warranty. Guess, my dishes will air dry, and I might as well do them myself!

Special features eg changing HE detergent conc. ratio for auto add feature in Load and Go is impossible to find, extra rinse doesnt work. No extra spin which would be useful for bulky loads. But preset cycles work fine and machine has very low vibration a big plus.

Cabrios have an inherent F1 error problem, The company had an initial recall and fixed it once, but problem reoccurred about 14 months later. Company declined to fix it. If there is any type of lemon law on appliances, this would apply. I would not recommend this washer.

I bought a Cabrio washer in 2009. I started receiving the infamous F51 code. When I called Whirlpool, they refused to even acknowledge that there is a problem with this washer. When I brought up the pages and pages of complaints about it, they acted like they did not exist. I hope this review will deter people from purchasing one of these faulty products!

No matter what I do after I wash clothes on quick or deep water cycle or even running the cycle over again, the clothes are left with soap residue. This is very annoying, particularly on dark clothing because it stands out. If I could start over, I would purchase a washer with an agitator. I watch the clothes as it goes through a cycle and the clothes stay in the same position...no wonder they dont get clean. What a ripoff!!

I was very excited when Melanie from Whirlpool customer service called me back about my complaint. WHAT A JOKE! I thought she was going to offer at least a repair considering by her own admission this same problem with my control panel of my double oven happened just last May (dead for the third time). Instead she offered me 15 to 30% off a new product if I bought it in the next 30 days! ARE YOU KIDDING ME?The first time the control panel died was when I used the self-cleaning feature. The oven never turned on again. Cost me hundreds. I have been afraid to use the self-clean feature ever since. The second time was in May and is no longer under warranty? Again it cost me hundreds!! Now I am supposed to be happy with 15% off another one of your products? Why would I have any faith in any of your products? I have since found out that Whirlpool has had so many problems with this model - they have quit making it. The repair man says Whirlpool cant make the control panels fast enough to keep up with all the repairs but this is still not under warranty - how about a recall? Do you guys stand by your products at all?

I have a Whirlpool Gold Series dishwasher. I would recommend this dishwasher. It is large enough to hold dirty dishes for a family of four. It is a little loud but not that bothersome. It is stainless steel but I don’t have a lot of fingerprint smears and stains.

We built 8 years ago, with ALL new appliances...All Whirlpool Gold...been very unsatisfied with ALL appliances... Had to replace range and parts for refrigerator..And extendend warranties all nonusable..We live NM off a tarred county road by 1/4 mile...no one wants to even come and look. Not good.

Called 8/24/15 - spoke with representative about our two year old washer. Nothing Whirlpool can or will do.They have no other complaints about rust inside the lid and inside rim at bleach dispenser nor chipping of paint from lid. When asking the Whirlpool representative about the rust, he assured us there were no other complaints.This is hard to believe since our recent research clearly shows that other brands have had to replace tops due to rust. As for clothes not cleaning, no response to this issue. Whirlpool has not trained salespersons and therefore at the mercy of Lowes hard sales tactics and we were very delinquent in researching numerous complaints before purchasing Whirlpool Cabrio Platinum Model WTW8240YWD - Ranked lowest possible from ConsumerAffairs with hundreds of complaints. Whirlpool should be ashamed of product - clothes do not come clean, there is no soak cycle, no way to open mid cycle without losing all water, washer smells horribly, must be cleaned - are you kidding? Who cleans the washer that is supposed to clean clothes with a special cleaner?? We understand safety issues of water in open machine, wonder if Whirlpool understands the need to have a soak feature to clean clothes. Undereducated buyers like us and the totally undereducated salesperson at Lowes were obviously a horrible combination. It was all about sales for them. No one mentioned and we had no clue that the huge drum would not clean clothes even using less water than a traditional machine. We thought platinum meant a high quality machine. It clearly was a cleverly used buzz word for sales not a premier cleaning machine. Never, never, never purchasing Whirpool anything again. Wonder if Whirlpool cares, if they read the ConsumerAffairs reports, if they respond. Our hard-earned money is wasted. Our clothes are dirty, the washer smells, and the top is rusting out!

I stumbled across this site while browsing the Net, looking for a way to deal with the same situation I now know you all have been struggling with: Whirlpool Washing Machine! I wonder: Is NASA still accepting volunteers for their living on Mars experiment? Id rather beat my clothes on a rock than touch that POS Whirlpool that has me back on tranquilizers! Mine was purchased about 2 years ago when I was in bad health and my son was handling my affairs. I could tell - just by listening - there was something very wrong with it, from the first load my son attempted to wash. It would start and stop, restart, restop, ad infinitum and made a terrible racket. I told him nobody would intentionally make a machine like that--something had to be wrong with it but he assured me that he had checked both with the store that sold it and he also read the manual. He had a hard time accepting but we thought maybe this was because it was new and would settle down after some use; after all, the store (Best Buy) assured him the sound was normal for this particular machine. However, the weird sounds did NOT lessen nor stop, nor did the starts and stops. Little did we know, this was just the tip of the iceberg! We have encountered/suffered through every nasty performance detailed here: low water, wont spin, leaves clothes soaking wet, wont spin out excess water, lid locks (grrrrrr), it cant seem to switch from one procedure to the next; there is nothing washing the dirt out of the clothes--they just sit in the water and soak(?), then the water is released. Clothes come out with stains still on, so wet that the water must be wrung out of them! Very hard for me with arthritis all through my body! Ive tried countless times to reset machine to Drain & Spin. Ive even waited (yawn) for it to unlock so I can open and then readjust the heavy/wet laundry, trying to make it even all the way around so to avoid an unbalance. But nothing helps. It will start to spin. And then it stops. (wait, wait) Starts to spin again. Stops. (wait, wait) Starts again, does it a bit longer. (start to relax) Stops. Ive spent HOURS engaged in that kind of mindless, maddening frustration, just trying to wash one small-medium load. (I wash only for one person--myself, now.) My son, who got married and no longer lives with me, said the only way he could manage to struggle through it - and agrees it DOES take an inordinate amount of time--for just ONE load, he has to put the settings so that it washes in Deep Water even if small load. He sets Rinse, to 2 Rinses. He sets it to Soak even if the soil is light. Even then, it still makes noises, starts and stops, has to be adjusted several times during Drain & Spin. Last but not least, the noxious odor: OMG! I left one batch of laundry in the machine, with the lid open, as it was very late so figured Id dry them next morning. Some hours later when I went back to shake them out and put in clothes dryer, they smelled so awful, I had to wash them all over again! In fact, Ive had to follow my sons admonition to leave the lid up AT ALL TIMES unless actually washing in order to keep down the stink. I washed my last load with Baking Soda added to wash cycle in an attempt to lessen the odor and get laundry cleaner. Someone here wrote - in their review - that there should be a Class Action (Law) Suit filed against Whirlpool. I AGREE!!! And I want to opt IN on it. There are several law firms that advertise on t.v. that specialize in Class Actions. It would take some time and paperwork but will not cost us anything unless we win the case. Then the law firm gets a percentage. I am willing to work with one more others here who truly want to settle out this problem. I cant believe 2,000 (and thats only here), people are willing to eat hundreds, thousands of dollars of worthless, mind-gripping, rubble such as we have spent our hard-earned money. Other manufacturers recall their defective merchandise and/or replace it, or make arrangements with the retail stores who carry it to make amends, free repairs, whatever it takes to make dissatisfied, disenfranchised customers, whole. We paid for these demons from hell and we deserve to get an equivalent in merchandise (that works properly) or services. That is how it is done here in the U.S. For the life of me, I just cant comprehend why Whirlpool has been allowed to continue selling this junk--why no entity or person or lawsuit has stopped them! As I said, I am willing to work with a core group who is serious about filing a Class Action (Law) Suit against Whirlpool. It may be that the retail stores would be included as well; however, that is a matter best left to the discretion of whichever law firm we select to represent us. For those of you here who do NOT wish to be included, do not worry; you are not being pushed into anything. The way Class Actions work, you have the choice to opt IN (be included to receive your pro-rata share of what is collected). Or you are completely free to opt OUT. By opting out, that means you do not wish to be part of the Class Action and therefore, you will not be included nor will you receive any portion of the recompense collected via the Class Action. Just for your information, though: You are allowed, by law, to bring your OWN lawsuit against all or some of the same parties. The most common reason for opting out, is if you have suffered an extra large financial loss and prefer to file your own suit in order to collect ALL recompense; whereas, sometimes - in a Class Action - the individual plaintiffs may not recoup the total amount they feel they have lost. If you DO decide to opt out and go on your own, realize you will be fully responsible for lawyer fees (although you CAN add them into the balance you are seeking in your suit. Settlement of your claim may or may not include lawyers fees.) Good Luck to all. To those who wish to file a Class Action with some of the rest of us, please contact me if you want me as part of the core group of plaintiffs.

It is a really great microwave, but the door is falling off of it. We can still use it, but try to be careful about it. I honestly and truthfully love my whirlpool microwave as well as my whole set of whirl pool appliances. The door is trying to fall off, but we can still use the microwave. If we get another one we will probably get another whirlpool because I love it so much.

DO NOT buy Whirlpool branded electric ovens. Whirlpool put out an update and it fried the control board of our electric built in oven. They refuse to fix it. They have kept us on hold for two hours and then tell us there is nothing they can do to fix it. We had an extended warranty that just “disappeared from their system.” They told us someone would call back us but no one has. This was an update we were told we had to run in order to use the associated APP. Our oven is only 2-years old. We now will need to pay for the repair ourselves. DO NOT BUY.

I purchased a washer, dryer and refrigerator from Sears and it has been a terrible experience! The fridge broke twice, the dryer broke twice, and the washer broke around four times! I was told that since they fixed it last time for free, this repair was on me! If all the items didnt break numerous times, I would not be upset. But for all the items to break so many times, thats telling me that I shopped at the wrong store! The Whirlpool Cabrio sucks! So, I was told by Sears on 8/1/11 to ** it up!

I purchased a Whirlpool Ref side by side 11-2013. I have had nothing but trouble. First the Ice maker leaked, was fixed. The door to the ref has had serviced 5 times. The tech after many times trying to fix hinge on door twice was told to order new door. This took 6-8 week to get. Came today 5-27-15 too but new door on. It is still not right, has big gap in the middle - still not level as should be. I have called Customer Service again today with no help. All they want you to do is spend more money on a contract. I THOUGHT WHIRLPOOL WAS SUPPOSED TO BE A GOOD PRODUCT......NOTTA....WILL NEVER BUY THIS PRODUCT AGAIN. SO IF YOU EVER BUY WHIRLPOOL PRODUCT BE SURE TO GET EXTENDED WARRANTY. YOU MIGHT NEED IT..........STILL NOT SATISFIED AND NO HELP IN SIGHT.

We bought a side by side refrigerator/freezer in 2013 from our local Best Buy. We have usually bought Whirlpool appliances. Before we bought this refrigerator the last Whirlpool we had for 25 years. This past week our refrigerator went out. We called a repair man. He said the circuit board was out and would cost $450.00 to replace it. We decided to buy a new one. I am very disappointed that it only lasted 7 years. Oh I forgot to mention the ice maker went out about a year ago. We did get new filters as instructed. We did not buy another Whirlpool.

I bought a Whirlpool model # WRF757SDEM. It has failed twice in 7 months. The tops temperature hovers at 54 degrees Fahrenheit. The freezer works fine. I had a whirlpool fridge for 10 years before I bought this one and never had trouble with it. This particular model seems to have a design flaws according to other reviews I saw on this site that read similar to mine. We are waiting on parts. This is the second time in 6-7 weeks that it breaks down.

My dryer lasted 18 months and then died! All parts have been replaced. $700 and highly rated, I dont know by WHO but would love to have a chat with them.

I had an addition added to my home in 9/2007, which included a new bathroom. A whirlpool hot water tank was added. This week, I woke up to no hot water, so I called the whirlpool customer number regarding the warranty on the model FG1F4034T3NOV. T hey told me the serial number shows its out of warranty, although I may have only had it since 2007. They also said there was a screen that needed to be clean under the bottom of, it that if not clean, would make it stop working. Since homeowners where not cleaning it, they have made a replacement door part that would fix it, and do away with the problem, but I would have to pay $35 for it. I asked them, since the serial number shows that the part has not been replaced on this unit, why not just send it to me, and I pay to have it put on. The person said no, you will have to pay for it if I wanted the part to fix it . Although my builder did not give me the receipt for it, thats just not right. If a manufacturer knows they are having problems with their product, which require a part replacement, and they have produced one, they should be willing to give the part to everyone with the product that request it. On top of that, this model has the left hand threaded thermocouple, which no one around seems to carry. I am totally disappointed with Whirlpool, and right now would not consider buying, or have any more of their products installed into my home.

I purchased this fridge in February 2015. In August, the handle on the fridge door broke. I called for a replacement on 8/7, on 9/14/15 I received it. It broke on 10/3/15 and had a replacement on 10/13/15. It broke again on 12/26/15. I called for a replacement. I should get it in 10 days. Obviously, there is a flaw in their design. What bothers me is that no one seems to care. I will hope I never have to buy a Whirlpool product again. And I will certainly discourage anyone I know who is thinking about buying their products. I purchased this product at Lowes and they did not care when I went to them.

Washer keeps saying F1 and it wont spin. In the middle of load it will stop and it would say F1... It started just a year when we bought it. Now its two years. Its really broke. Before it would say F1 then I give an hour then try again and it works but now no matter what I do it really wont work... I dont know no one who could help me whats this F1... So sad. Its not cheap washer but its junk.

I purchased the Whirlpool Quiet Partner II dishwasher, Model DU1055XTVQ0, Serial # FY3762359. The racks are cheaply made and rusting! Almost all of the tips on the racks are rusting, causing them to corrode and break off completely! This dishwasher is well under 5 years old. Not sure what we paid for this machine but the racks should not be doing this after this short length of time. They shouldnt be doing this after any length of time.I called Whirlpools customer support center today and was told there is nothing they could do. The support agent asked if I had hard water, if so, that could be causing the problem (I dont have hard water). The agent stated that they do not cover rusting racks nor would they replace them, now I see why. They are expensive to replace. As of now, I will not be buying another Whirlpool appliance - ever! They just lost a dissatisfied customer due to their very poor quality and customer service.

Ive had a Whirlpool range for not even a year yet and the thing is on its third repair! First, the motherboard goes out twice. Then, a month after the second motherboard replacement, the broiler drawer handles melts off! ABT has been good at repairing it but seriously, I got the appliance last May! Now, Ive been waiting two months for some insulation piece on the handle. I think this product is a lemon and I am highly disappointed in this brand. I had called Whirlpool regarding this and they said their technicians would have to inspect the product and repair it. I trust them less to repair the stove than ABT!

I absolutely hate this expensive piece of junk. I have tried everything, and my clothes are not clean. It is only myself, and my husband, and our clothes dont get very dirty. I would like to send this junk to the junkyard, but I spent a lot to get the dryer with steam that went with the washer. This experience has soured me on Whirlpool appliances, and now I learn they also make appliances for Maytag!

Four years ago, my wife and I also purchased a Whirlpool washer and dryer set, washer model no. WTW6600SB2. Within the first year we had to replace both pumps twice, user interface, and control board. (I think that’s what it was called). Of course, that was all covered under warranty. But I to had to wait a week for the part and then another week for the repairman to make it. The user interface and control board had to be replaced because moisture got into the control panel and caused corrosion on the circuit boards which caused them to short out. Then it wasn’t long after warranty ran out, the whole wash tub and drum just dropped to the floor with a full load in it. I don’t remember exactly what was the cause of it, but I do remember it cost me $580 to fix it. Then it wasnt more than two weeks later, the repairman had to come again and replace the control board again. There went another $600 for the parts, labor and service call because this time they had to come from 40 miles away and it’s a minimum fee of $89 just for them to drive up here and another $60 for diagnostics, and then the part and their time to install new board. I paid for this machine twice in the first year and a half. Then after all of that, it was finally working like it should and worked great for about 6 months, then came the UL,LD, and Lid Lock codes over and over unplug, plug in, unplug, plug in. That lasted for about a month, and then all of a sudden, it straightened out. And we only got the occasional UL code. Now in the last year, I have had to replace the drain pump twice and then the drum and motor dropped on the shaft allowing any loose change or other items if accidentally missed during pocket searches to fall into the outer wash tub and get sucked into the drain pump and causing a quarter to be shoot through the drain pump making a hole and caused my laundry room to flood. Well, I decided I wasn’t going to buy another part so I used a plastic repair kit to fix the hole and got it up and running. A week later, the washer won’t wash. It will fill and that’s it. So upon my own diagnostic, I came to the conclusion that it was the user interface that went out due to corrosion I found on it. So for another $120 I can fix it, but I’m not sticking another dime into the washer, nor will I ever buy another Whirlpool appliance. Once all of my Whirlpool appliances die, I will replace them one at a time with LG. I to contacted Whirlpool about my problems and all they did for me was send me an extended warranty offer for 50% off, really that’s it, that’s all I get is a big GFY after all the money I have stuck into this piece of scrap-metal. Well, never again will you have my business as long as I live. Whirlpool, you need to take your hoo-ya and do something about all of these complaints.

My stainless steel french door refrigerators compressor quit working and needed replaced after 3 years and 10 months. I had to buy a replacement kit and it cost 400.00. The repairman cost 175.00. I tried to buy an extended warranty but they do not sell them. You get a 1 year warranty. The repairman told me you will be very lucky if you get 4 years out of the replacement. He said all of the new compressors are really junk. Remember when refrigerators used to last 30 to 40 years. Not anymore. It is a money racket. Do not buy anything Energy Star, it is all junk. I have gone through 5 washing machines in 18 years, and I live here by myself.

We've had a of Whirlpool washer and dryer for well over 8 years now. The only thing we've had done to it during that time was to give it a "tune up". That was done by a friend and only took a half hour or so. I don't know exactly what he did to it but the "tune up" didn't require any parts. In fact, when my friend was finished with his version of a tune up, it was as if it were turbo-charged and our clothes came out cleaner than ever. The washer runs quietly, as far as washers go, and the capacity, washing options, etc. are perfect for a washer that gets a ton of usage.

I purchased a Whirlpool WTW6600SW in January 2010. I dont normally purchase an extended warranty, but it was a fairly expensive washer. So I did. In July 2011, water starts gushing all over the floor. After my first visit to see what is wrong, I ordered a part. I was out of a washer for 2 weeks. Then in August 2012 the same thing happened. This time the repairman didnt get the part on properly, so they had to come back a third time. I am out of a washer for about 3 weeks. Now, October 2012, it is doing the same thing again! Customer service tells me it has to be repaired for the same problem four times in the same 12 months in order to receive any replacement value. It will have to break two more times! This washer is a piece of junk!

In 2013, my husband purchased a Whirlpool Hot Water Heater model #E2F40RD045V 40 gal. from Lowes in Vancouver, WA. On 12/12/15, had to call a plumber, the hot water heater was intermittent hot/cold. He flushed it, checked all power connections and changed the elements. On 3/18/16, NO hot water. Having a 6 year warranty, I called Whirlpool. They gave all kinds of excuses and told me to try a bunch of tests. By the time I got back to call them they were closed. I called them again on Monday 3/21/16 and said nothing worked and it had popped the breaker. They said change the elements. I told them I had just changed the elements 3 months before. I told them it was faulty wiring. They said the top element must be faulty. I gave up at that point and called the plumber. He came right out the next day. I had purchased a Rheem hot water heater to install and asked him to check the Whirlpool hot water heater elements he installed before he removed it. That is when it was discovered that under the insulation around the bottom element it was all scorched from FAULTY wiring. I called Whirlpool again and told them I could send them a picture and they said dont bother and immediately gave me an RA to return the hot water heater to Lowes. I told them I had already purchased another hot water heater and it was not a Whirlpool. I am going to request a refund.

We purchased a Whirlpool refrigerator (WRT5L1SMYF00) in April 2012. Within 2-1/2 months, items were freezing on the shelves of the fridge box. I called Lowes & was told to call Whirlpool. I did as suggested & they sent out their service co. tech, Turner Consumer Services. I had all the same issues as everyone else in these reviews. i.e., food freezing where it shouldnt or spoiling when the stat was turned down even one notch. The staff at Whirlpool was as uncooperative as is possible. They smiled and lied to my face during phone calls - anything to get me off the phone. During the next 4 months (till Nov.), techs came out 5 times, never having the part needed on the truck. Always, it was my fault somehow that my stuff was freezing. Their chosen tech service employees were rude, condescending and without knowledge. Five service calls, 3 parts replaced and numerous calls to Turner & Whirlpool got me nothing but stalling tactics. I, too, was told that their tech had to fail the appliance before they could consider replacement - all lies. The tech, when he gets here, says hes not allowed to fail the unit. On the 11th of Nov., I awoke to totally frozen-up coils which kept the fridge box from cooling. We had company here from out of town. We moved out the new fridge, moved back in our 21-yr-old unit and got through till our visitors left. Whirlpool has been completely unresponsive to my appeals for some relief from this fiasco. I continue to receive requests from Whirlpool to purchase an extended warranty. Really? My husband & I went out to Sears and purchased a GE & have had no issues with it whatsoever. We are older, on a fixed income, and can ill afford to purchase 2 fridges in 7 months, not that Whirlpool cares. Not only will I never buy another Whirlpool product, but I will warn everyone possible to not buy from them. In fact, my intention is to use every possible forum, Facebook, Twitter, any & all review sites here in KC, MO or anywhere to put Whirlpool down. I am, however, considering one more expense - a lawyer.

I purchased a high dollar built in side by side fridge with custom panels in 4/2005 and had my first service call in 5/2005. Since 2005 we have had 11 service call mostly for defrost failures and over temp. readings. From 2011-11/20/2013 we were issue free then the fridge over temp alarm sounded and we could not hear the fan motor. We had the certified tech come out to evaluate and found that the main control board needed to be replaced. Kitchen Aid/Whirlpool no longer make this item and forwarded us to Core Centric solutions to have a new one built. After speaking with the certified tech who had been out to service our fridge 11 times he informed us that these boards in his experience have never lasted more than a year. We spoke with a customer service rep a Kitchen Aid and asked about a prorated discount on a new built in fridge and she said it seemed reasonable but after checking for authorization informed me I needed to have the board rebuilt at my own cost and that even though this typically takes about 4 weeks to build the fact that our family would be without a fridge is not Kitchen Aids problem. 6/20/2005-over temp/not cooling call (replaced defrost thermostat) 9/2005-over temp/freezer iced over in bottom (freezer decided and drain unclogged) 10/05-over temp/not cooling (replaced fan motor) 9/06-over temp/freezer iced over in bottom (drain line decided, kitchen aid had no advice on how to fix) 10/06-over temp/not cooling, ice build up (whirlpool recommended replace heat kit and bimetal) 11/7-over temp and ice buildup in freezer with leakage (adj to drain pump and defrost drain basin made) 11/07- over temp and freezer icing over (whirlpool sent out a new heater probe) 6/08-over temp and ice buildup (bimetal and foam block replaced) 10/09-over temp, lights and motor shutting on and off (replaced defective board) 10/09- fan making excessive noise (ice buildup found on evaporator fan)11/13-over temp ice buildup in freezer, burning smell from fridge and no air movement or cooling in either compartment (need board rebuilt as on 10/09)Board no longer available from whirlpool, must be custom built at owners expense and will take up to 4 weeks. D/t continuing issues and whirlpool not willing to help the customer with replacement I would highly suggest no one buy a Kitchen Aid fridge.

Bought a Whirlpool refrigerator from Best Buy a yr 1/2 ago. Went wrong from delivery and never stopped! There isnt enough room here to specify so Ill try to synopsis this. They screwed up delivery date and then time. Fridge was unbalanced, doors wouldnt close delivery guys didnt know what to do. Tried to fix it and then call their office and were put on hold for over 30 mins. And the Rep was unhelpful and rude to me and then the delivery guys finally got door shut on freezer but Ice maker wouldnt work so they said they would have to have someone Whirlpool to fix it after them talking and being on hold again with their Rep. They were upset and late and felt sorry for me and told me Confidentially That this was not uncommon and they would do what they could to help me.It took many calls, people and conversations (subsequently I found dents, drawers cracked, cracks in back wall) for them to get someone here. When they did the guy was rude and acted like a pre-programmed robot. He said, Show me whats wrong and I did. He stood there and just stared at me and said, I dont see anything wrong. I was shocked! I said, You mean thats supposed to shower the kitchen with crushed ice, etc? He said YES! I said, Ok, please leave my home. I will contact Whirlpool and Best Buy Again. I did and it went on and on and on and to this day theyve done nothing. I have copious notes, dates, names etc. I have also heard many other complaints about both companies and will never do business with either again and will tell anyone and everyone I meet.

Love my new fridge, not in love with the icemaker though. Every couple of days I have to reach in and scoop the ice off the little shelf in the back, or else it will quit making ice. The ice cubes block the arm from coming back down to trigger a refill.

I purchased a home from Pulte and closed in June of 2020 and had no choice but to take Whirlpool appliances. Pulte does not offer high end appliances in order to maximize their profit. The first thing that failed after only 3 months was the Microwave and because we didnt want to get the same cheap microwave we upgraded and paid 400 for a Kitchen Aid, same size but never received the trim kit that matches the oven that came in sometime in October 2020. It is now January 2022 and we are still waiting for the trim kit. Every time we call to find out we spend hours on the phone.The refrigerator is a cheap version of the worst refrigerator made in China, the ice maker works ok but ice gets stuck in the chute and when it doesnt get stuck half goes to the glass and the other half to the floor. Poor design and we are stuck with it. Tried to buy an LG from Costco but it wont go through the door so again we are stuck with this small refrigerator with no room for groceries for two people. Stovetop is also cheap, only looks good the day we got the house, one of the burners would go off when turned to low with gas still flowing. Grates look 10 years old but must admit we cook every day. Oven will not calibrate and it is not accurate so we have learned to set everything 10 degrees higher to make up for the variance. Dishwasher had issues as well, unless you run it for 3 hours the shorter settings always have dishes or utensils still soiled. Warranties have expired after one year so it is now time to replace almost everything if we want decent appliances. Very disappointed but I blame Pulte for buying cheap.

We purchased the Whirlpool Double Oven Range model GGG388LXS in April of 2011. The reason we purchased the oven is that we are empty nesters. We almost exclusively use the small top oven. We have streaks between the double glass on the bottom oven. We can not clean it. It is obviously a design flaw. I looked on this site to see if others have the same problem as it is too early to talk to customer service at Whirlpool. How have others fared with this obvious flaw?

A couple of years ago I replaced my Whirlpool gas range because after seven years, the house was growing a gas smell that was becoming stronger. I called the gas company and they determined that it was the oven and not their problem. I called an appliance person who could not find the leak but charged me for the service call. Before I had him leave though, I called the gas company back and had the two talk. There was a conflict with their assessments. The service guy left frustrated. The gas company guy came back and again checked and told me that the oven is definitely leaking. He told me they use instruments, not soap, to determine leaks. With this, I was mad at the appliance company. After voicing my frustration, they were going to allow me to purchase a similar new Whirlpool freestanding gas range at a discount and deliver it for free. I relented and spent close to $600 for the new range. After installation, I realized that the quality was cheaper than my old one. The metal rods in the oven racks are thinner and less of them so they are further apart. The cooktop grates are already wearing and chipping. But the thing that has irked me the most is the burners. You cant adjust them to low for a long simmer because the flame goes out, not immediately, but when youre not around to watch it; and the whole house smells of gas fumes! I called the appliance store and they said that because I didnt buy an extended warranty and that a year has already passed, I would have to pay for the service charge. I called Whirlpool and they said that they have not encountered this problem with their stoves yet. Even while on the phone, I could turn every burner on separately and the flame would go out in a circular motion as I turned the knob to low. The only suggestion they had was to call my appliance company and have them look at it. I got nowhere and I was quite frustrated! These Whirlpool stoves should be recalled! Gas leaks are dangerous! I will never buy a Whirlpool again!

Our 3 year old 2013 whirlpool gold French door refrigerator was not cold enough in the freezer. I tried a few self help remedies. Then had repairman. He had good news, bad news. Good news is Whirlpool will replace the evaporator because, they know they have a problem with the part. Bad news is, they wont cover the labor which is $400.00. Freezer now fine. Has anyone else had this situation. I am pretty angry that they wont cover labor for a part they know is defective.

We purchased a Whirlpool Cabrio washer brand new from Lowes. It did great for about 6 months when a terrible grinding noise started. Then it also would not spin dry the clothes - they would come out completely soaked. Repair guy came out and fixed it. Lasted for about 1 year - same thing again. Lasted about 1.5 years this time and now the loud grinding is back and my wife - who Ive heard cuss just a couple times in 20+ years - said, This ** thing sucks. The clothes are soaked. I cant stand this washing machine. So, Off we go to buy a new machine. Definitely not a Whirlpool though. Id give this machine 1 star because it does a decent job for a while but major repairs 3 times in five years is not what I deem an acceptable appliance.

My wife and I purchased a new Whirlpool Cabrio Washer / Dryer set approximately three years ago and have had nothing but problem after problem with these units. Weve had multiple service calls, multiple parts replaced, and after dumping hundreds of dollars into repairs and service calls (even called Whirlpool and asked for some help with parts cost but was given the cold shoulder and was told, We cant help you), we are dumping these machines where they belong - scrap heap. I will never purchase another Whirlpool product and will tell anyone who will listen what garbage Whirlpool manufacturers are and absolutely pathetic excuse for customer service and the poorest of quality product. Whirlpool will never be in my familys home again and will never see another cent of my monies.

No get this and the dryer used. Top of the line. I am having fun seeing all the choices. I would recommend because of the efficiency. Measures soap and softener depending on the load size. Like a miracle.