I bought the Ikea dishwasher (model IUD8500BX1) in 2014. Because it’s from Ikea, it has 5 year warranty. I was using it daily, as I have a family of 5 and we cook and eat at home most days. I have called Whirlpool at least 4 times according to the repairman that was here today. Ive already had to replace the pump because it was holding up water. After which, mold started occurring in the washer. The technician who came out found 4 fault codes on the machine. He was prepared to replace sensors and the circuit board for the heater and the pump, since it likely had mold. But Whirlpool says the parts are functional therefore the replacement parts won’t fix it. He is not allowed to replace anything.Considering the mold is an after effect of the failure to drain, you would think they would fix the mold as well. A replacement dishwasher would be nice, but at least replacement of the internal plastic parts that I cant clean. Instead, they tell me to bleach wash it and run a cycle with bleach. Guess what, Ive already done that. And according to the technician hes never seen a dishwasher have this much mold when it’s used as often as I use it. If you are buying this product thinking they will stand by their product, think again.

I called Whirlpool about the refrigerator that I purchased in June of this year and nothing was done about it. My situation is that the refrigerator scratches very easily. It seems that it gets scratch only by looking at it. This refrigerator is very expensive and I not even done paying for it and this appliance looks awful!! Susan the person that I was chatting with just told me that cosmetic doesnt cover and there is nothing that Whirlpool can do about. It bothers me that paying so much money for something that it is poor quality material.

We bought the Whirlpool NU50T122-403 50 Gal water heater from Lowe’s and very disappointed that after 3 years it will cost more to repair it than replace it. The Whirlpool gas water heater and our Whirlpool refrigerator have been the worst purchases ever made. Whirlpool has been unreliable in our house and the repairs and downtime have been extraordinary. We have replaced with a Rheem from Home Depot.

I have had a plumbing company work on my Whirlpool water heater three times in the last two months. On the third visit, he told me all the problems customers have had with Whirlpool water heaters. I decided to call Whirlpool for warranty purposes. The unit is three years old. I was told that it was the gas valve, and I was given a free one from Lowes. After installing the new valve, it still did not work properly. After troubleshooting with a technician, I was told it was the orifice. I have had to do all the labor myself, and I dont know how long this is going to go on. I have heard Whirlpool will continue to give you the runaround (from the plumbing company and Lowes salesmen) and will continue to give you the runaround and not replace the unit. They are wearing me down. I have been without hot water for three weeks with no end in sight. I am ready to give up and just buy another water heater but certainly not a Whirlpool.

Purchased double range ovens. Enamel is flaking off within 2 years. Whirlpool denies defect. They wont replace it. Any other folks with similar problems? What can I do to have it replaced? I remember the old ovens and how the enamel just stayed and stayed and stayed. Never a rust or flaking issue in those old time models. Any expertise on how the enameling process may be compromised in the newer manufacturing process (cutting corners or costs). Any options for a class action here if a commonly experienced occurrence? If similar experience drops comments/review below as a one liner - just state enamel defect. That way can figure out the number of folks with issues. Id like to take action if given the opportunity, and more so if this is a common occurrence. Lawyers are costly for one-off complaints, but there is power in numbers (think United Airlines).

I bought my Whirlpool gas stovetop in March of 2016. The burner knobs that connect to the stove is made of plastic and all 5 knobs broke within the first year. Each year I have replaced knobs and had issues with the knob breaking and then not being able to tell if the gas is off or on. I have called and talked to people at Whirlpool about this issue several times. Although they seemed concerned they will not replace the knobs and I have had to purchase them through Whirlpool. The gas stovetop obviously has a serious and extremely dangerous design flaw. I have kept some of the broken knobs just to tell others about this terrifying flaw. Again, last night the gas was on for several hours before we discovered it!! I called Whirlpool again and they were unconcerned. The Model is #WCG97US0DS00, Serial#D60509297. Beware and DO NOT PURCHASE this gas stovetop. I wish I had not bought mine.

I bought a Whirlpool refrigerator in April. The motor ran constantly. The company replaced it for me but it was back ordered until July. The one delivered in July kept freezing the items in my refrigerator. I had two service people come out to replace parts in the next couple of months. The entire time having to throw out frozen food. Finally, they had another one delivered in November. This one continues to freeze food in the refrigerator. Mind you, I just got it and they want to start again with service. Seems others are having the same issues. My 4 month old gas oven is also not broiling. Customer service is awful. Every time I call the wait time is over an hour and then they don’t really help. I would not recommended Whirlpool to anyone.

After 2-1/2 years we started having trouble with the spin cycle on our Maytag washer. We live in an area with no repairman. Whirlpool want us to pay just to talk to us. Now the timings off. It will not spin out.

We bought the Gold Series Whirlpool fridge (Model WRF990SLAM00) in December 2013. A few months after its first repair, (dripping on the top left inside of the fridge), which happened within the first year and was covered by the manufacturer’s warranty, it started to make an incredibly loud whirring sound that kept us up at night. Our bedroom is upstairs and far away from our kitchen, and I had to sleep with earplugs to not hear the noise. We tested the noise on a decibel app and it came in between 66-70. A normal fridge noise level should be around 52 decibels. We had a repairman come out and he replaced a fan even though he told me it wasnt going to fix the problem. Wait, what? After he replaced the fan and the whir continued, we called Lowes extended warranty again, and they sent out a different company: 1-800-Appliance.The second guy replaced two kits and found some issue with the ice maker, which we were not even aware of, but the noise remained, and he then had the gall to say it was a normal noise. If it was normal, wouldnt it have been making that noise the first year we had it? We had 1-800-Appliance come out again and he determined he couldnt fix it, so Lowes sent another guy from the same company, and he replaced the same fan that the first guy replaced, which was clearly not the problem. Three perfectly good fans were wasted. BTW, the repairman who said the noise was normal told us that the fridge had a part that was made to be replaced after purchase because if Whirlpool had the part at the point of sale, the fridge would not meet the Energy Star standards. Hello, lawsuit! After three repairs for the same problem and five visits that did not fix the problem, we were told Lowes would issue us a return order in three days. Finally!Not so fast... one week later, no one called, so I called them and then Lowes denied having told us that! We gave them the name of the person who told us they would take the fridge back, but the woman on the other end said she had no record of that (how convenient) and, despite the California lemon law requiring only three attempts at a repair, they would require yet another attempt by one of their repairmen. She told me that if he determined the noise was abnormally loud and not repairable, then she could contact the manufacturer and go from there. So they sent a guy from the first company out and he wrote down that the fridge was not repairable and was very noisy. He said that should take the fridge back at that point.My husband called Lowes several days later after not being contacted by them and they told him that they need to send a different repairman out from 1-800-Appliance and that only 1-800-Appliance could determine if we could get a refund. If that was true, then why send the other company out? By the way, the second guy sent out by 1-800-Appliance wrote down that the noise was very loud and wasnt fixed by his repair. But the notes Lowes said they received from him didnt say that at all. They told me that he wrote that the noise level was normal. I am starting to think there is collusion between Lowes and 1-800-Appliance. Something very wrong here. So, six visits later and horrible customer service from both Lowes and 1-800-appliance, we are now being told that the repairs need to be 30 days apart from each other before they will issue a return.If the cause of the noise was never actually repaired, then why do we have to wait a month between repairs? We continue to jump through the hoops that Lowes keeps throwing our way, but it is now clear that they have no intention of taking the fridge back. The fridge is less than two years old, and we have the extended warranty. We couldnt take the noise any further because it felt like it was causing hearing loss and after several months of that horrible sound we were both on edge, so we bought an amazingly quiet fridge from Pacific Sales, and they assured us that they would not do to us what Lowes did. Pacific Sales pride themselves with having good customer service. Lowes seems to have taken delight in lying to us, selling us a lemon, and then not righting a wrong.We have moved the loud piece of ** into our garage, and if Lowes continues to change the rules of a return and act in collusion with 1-800-appliance, probably in hopes that we will simply throw in the towel, then at least we dont have to hear that horrible sound in the meantime. If they dont do the right thing and take back the fridge, then we will simply keep calling out a repairman to fix the problem. We have three more years of our warranty, and if Lowes doesnt do the right thing, we will make them pay for this one way or another. Viva la revolucion!!

I bought Whirlpool top-loading high-efficiency low-water washer Sept 2018, model WTW5000DW, Serial # C83444466. Worst washing machine ever! No matter which water level you choose, it will not dispense enough water to cover the top of the clothes load, therefore the clothes are just moved from side to side with only the bottom layer of clothes getting wet; top clothes stay dry. Not enough water to fully agitate to clean the clothes!Whirlpool serviceman came today (Jan 13, 2020) to recalibrate the settings. VERY NICE MAN BUT THERE WAS NOTHING HE COULD DO TO SOLVE THE LOW WATER LEVEL. Recalibrating settings did nothing to solve the problem of not enough water. I am 81 years old and I have to manually add at least 4 buckets of water to an average load of clothes. This is unacceptable. Wont someone please initiate a class action lawsuit against Whirlpool for selling this very obvious poorly designed machine? NEVER EVER BUY A WHIRLPOOL WASHING MACHINE. It is a waste of money.

Frontload Sport Duet ht: After just 8 years, bearing out on washing machine. Just had repairman out. Cost more to fix than what I purchased it for. I bought both the washer and dryer, thus the reason for the duet. So now I have a good dryer and lost its mate. I am not going to purchase another one. Very disappointed. I will not be purchasing any more Whirlpool products in the future. Off to the laundromat.

Purchased a whirlpool water heater 04/08/2005 and it worked for a short time. It had a 6 year warranty. I had to replace the thermocoupler assembly 1 time and it worked fine until last week. 09/02/1011, 4 months after warranty ran out, the unit started leaking severely from the top ? (Could of understood the bottom) here. After investigating further and being told to basically pound salt by the warranty number I called, I removed the top cove r(glued on by spray in insulation) and carved away the spray in insulation. All the bosses/threaded fittings for the inlet outlet and anode rod were all leaking under the insulation where it could not be seen! I know for a fact this unit was leaking long before the warranty expired! But because of the way it is built it is impossible to see it!. I strongly feel this was a manufacturing defect and there are hundreds if not thousands of these units in people houses all over the country!

We bought a whirlpool water heater about two and a half years ago and started having problems with the pilot light going out. The gas company said that these have been recalled but he was wrong its the 2005 year. Sure we will have to buy a new water heater soon.

I have had no trouble with this ref. There is absolutely nothing bad I can say about it. Once or twice something has fallen behind the drawers/ranks in the freezer.

This is the second time since I have had the fridge in September 2011. I had to have a new compressor installed about two months ago, and now, it is doing the same thing again. I had lost all my food before and its happening again. Last time, it took over three weeks before the fridge got fixed.

I have purchased many Whirlpool ranges for my apartment buildings that I own and operate. They never give me a problem with operation or length of service. I only have to replace them when a tenant does something dastardly to them. My husband and I remodeled our kitchen and we purchased one for our kitchen too!

Handle needs smarter design. I purchased model #WRT311FZDM00 in November of 2015, didnt install in my new home till December. I am a single senior female, so there is little wear on the fridge, unlike a family of several people and with kids. The door handle actually broke just behind the screws that hold it in place, the plastic part of it broke into a couple of pieces. The cost to replace this handle is approximately $80, which is ridiculous in my opinion. Please start making things of quality materials instead of cheap plastic, especially at a stress point of a part. Even I know better than that. All 4 of my major kitchen appliances are Whirlpool, as well as my washer/dryer. I thought I was buying quality products. Hopefully things will hold up better with the other ones.

Plate in front of the door that is at the back of the water dispenser bowed out. Company will not fix even if the refrigerator is not a year old yet. Said it only covers things like this for thirty days. Do not buy a refrigerator that Whirlpool will not stand behind.

I purchase a new Whirlpool Calypso with Catalyst Washing Machine in 2006 after a house fire. Thinking that I was buying a great machine. I was so upset with my house burning that I never thought about the washing destroying my towels, rugs and sweaters until it was too late on the guarantee. I called the company and ask if there were any more complaints about this machine, and of course they said no. I ask if there was a recall and they said no. I told them that there needed to be a recall of this machine. I so want them to see the towels that I have to use. I am so embarrassed of my towels that I have to buy new when company comes. I made no difference on the price that I paid for the towels. They all were destroyed by this Whirlpool Washer. I have had enough, I am buying a new Washer and it will not be a Whirlpool. I believe that the right thing to do is for the Whirlpool company to put a recall on this machine and give our money back. I had a friend that is in charge of another washer company and had him to look at it. He said that if that was his customer complaining about his washer that they would automatically bring the customer another new machine. I wish I had went with his company. Shame on Whirlpool for treating their customers like they have.

I purchased this range/electric (ygfe461lvq0) two years ago. It worked fine, but once about a year ago, the oven overheated and the breaker had to be turned off to stop it. No error codes were displayed. Year two, the oven broiler element stays on regardless if using bake or broil. Oven will go into runaway mode and breaker or cancel button has to be pushed to stop it from over heating. This range is a fire hazard and should be recalled regardless of what age it is. I called Whirlpool at Sears which recommended a tech who arrived to tell me that the control board is shot and for a price of around $400.00, it could be replaced. What is up with that? I had to pay for the expensive tech, also for 15 minutes of work. Sears says that I should have taken the extended warranty plan for around $160. Do I have to pay for an extended plan to have my house burned down due to a defect in manufacturing from Whirlpool? This is disgusting that a company can get away with crap like this. How do you people sleep at night?

My experience w/ Whirlpool has been disastrous. Whatever you do read the reviews on products before purchasing, do your homework first before purchasing any major appliance. Whirlpool company and its employees are a joke. We are paying consumers and spent our hard earned dollars to support a company that could care less about us and our problems with their products they sell to us which are a piece of crap. I purchased a refrigerator made by Whirlpool from hhgregg in Oct 2015, which took 2 months to get it delivered. The refrigerator is not a year old yet, and cannot get anyone to come out to repair it. I have called Whirlpool numerous times, and so have my husband to come and repair a refrigerator that is less than a year old.The ice maker stopped working. Then I came home and discovered that the refrigerator is not cool, and everything in the bottom freezer had almost thawed out, and a repairman was supposed to come on August 31, 2016. It has been hot as Hades, during August, Sept, in the high 90s and they had the nerve to call and say they had to order the icemaker and when it came in someone would be out to fix it. I called the company in Maryland to find out what part did they order because a technician hadnt been out at this point to determine what part needed to be replaced. I called Whirlpool, and yes was put on hold for 45 minutes each time, and when I asked to speak to a manager, I was told that the manager said I could call a repairman and they would reimburse me up to $150.00. I replied That that is not my job. Your job is to send a repairman to fix it.The name of the company that they gave me and the phone number is located in Maryland, I live in the state of Virginia past Richmond, 3 hours away. Then I was told by the company in Maryland that they dont have technicians to Repair Whirlpool Refrigerators. This is totally unacceptable. It is Sept 19, and since August no one from Whirlpool has been out to fix it, neither have they tried to rectify the problem. Bottom Line, DO NOT BUY A WHIRLPOOL PRODUCT, not from hhgregg, Sears, Home Depot, Lowes, anywhere because this is how they treat customers. I have an 88 year old Aunt that lives with us that were responsible for, and she cant even get a glass of ice cold water from a brand new refrigerator thats still under warranty. Whats wrong with this picture?

Will never buy another Whirlpool/GE product again. Nothing but problems. Paid $1700 for a Whirlpool/goldstar refrigerator 2 years ago. Problems from the start with slide-out shelf cracking, evaporator fan burnt out within 2 years, digital display cannot read anymore. Now have another problem again - not cooling. Going to the trash. No wonder your stock price have dropped. I would sell off to. Whirlpool/GE have been going down hill for the last 5 years. Maybe more. Cheap products, do reflect, it just a matter of time, I would think you would address these issues in your product line, but it shows your company is all about profits instead of quality of products. Keep going like you are, and you will be bankrupt. Cheap overpriced and nothing but junk in any products you manufacture.

Whirlpool with four burner and the model that you self-clean the oven. It had all the features I wanted and Whirlpool has been around for a long time. Cost was right for my budget and it had all the options to it. I would have to move it out from the wall to find the model. Love the oven and the fact that I dont have to use caustic cleaners to clean it but simply have to wipe the dust out. One burner does not work and I will have to get it repaired. I shopped at a scratch and dent sale. The price was right and I could barely see the scratch and it had all the usual warranties. I need moderately priced appliances and if there were expensive features on it that I have not previously used, I would probably decline it. I do basic cooking and do not need expensive accessories. I can on my range and I have found the burners do not hold up well for canning. The burner I use for canning is the only one I have had problems with. That is the only problem I have had with the range at all. If anyone plans to can, consider purchasing the coil that is heavier to sustain the weight of the heavy canner. I would not be afraid to purchase Whirlpool again. My range is about 10 years old and other than that burner, I have had no difficulty. It is a mid-price range.

I got a new Whirlpool washing machine and dryer last year and Im very happy with both. I like the fact that it offers a quick cycle if you have a small load or need something quickly. If youre debating on what brand of washing machine you should buy I highly recommend Whirlpool or the other brands because Ive had really good luck with mine.

Whirlpool Gold Fridge - For all the people who have water collecting at the bottom of their freezer... There is a plug in the drain pan underneath that needs to be removed. It comes that way from the factory. Thank God, I have a smart Hubby and Father-in-Law. I find it INSANE that these Repair people have not caught on or do they just want to keep billing for Service Calls.

I have had a Whirlpool washer for less than 1 year and have had it serviced over 7 times with drain problems - code A10 being displayed. Have not been able to resolve the problem with neither the dealer nor the manufacturer. What a lemon!

Its a big buy to decided on fridge, bought one last year and the drawer keeps popping off the plastic piece. Who designs these to where the piece isnt long enough to stay put. The Veg filter in the back came broke so it doesnt stay on. Just upset to pay that much and have a really cheap product.

I was doing a routine refrigerator cleaning and the glass I was cleaning absolutely shattered all over my kitchen. Shards of glass are everywhere including my disposal. I called Whirlpool and talked to a customer service rep. Of course, this is not under warranty. So I asked to speak with a supervisor. All I could get from her is Sorry, youre disappointed. We can replace that part for $87.71. It has taken me over two hours to clean up all the glass. I wouldnt be upset if I had mishandled the glass, but it broke when I was drying it with a towel! I’m wondering if anyone elses glass shattered in the same fashion.

I had one of the first Maytag Neptunes. Loved it to pieces but finally had a problem and my beloved repair guy said it was almost 20 years old so to give up and move on. Obviously, cant be without a washer for very long so grabbed this Whirlpool Cabrio Platinum Washer. One of the biggest disappointments ever! Clothes come out streaked and splotched, dont smell very fresh or clean even straight after having been washed, stains dont come out even with pre-treating, have to run everything on heavy duty, whites are getting grayer by the week, and all-around horrid performance.Im ready to give up my Starbucks, start packing my lunches for a couple months, skip whatever treats I have to in order to get back to a quality machine that can actually WASH CLOTHES. I wondered exactly what it was or wasnt doing so I stood over it for half an hour. Initially, it loads up about a gallon of water and then spits it out over the rotating drum of clothes. Then it stops and spins that water out. I suspect the design logic was that it would force that gallon of water thru the clothes taking some dirt out with it. It repeats that stupid process several times. Then it finally gets a few inches of water in the bottom and the vestigial agitator tries to move it around.I watched one hand towel lie on top like a dead weasel, never getting pulled down or pushed out or whatever it was supposed to do to get down among the other items and squish together. Life throws me everything from sick kids spewing body fluids to people coming home reeking of hydraulic and other industrial fluids. When I say clean I mean CLEAN. This piece of junk couldnt satisfactorily process half a dozen dust rags. Neptune, Im coming back with my hat in my hand and a whole new appreciation!

Our new Maytag (i.e. owned by Whirlpool) oven/range is a stainless steel pile of junk. It takes FOREVER to pre-heat. The range elements take FOREVER to heat up. And like others on here, the Aqua Lift cleaning simply does not work. We put the oven through 3 back-to-back cycles and only the bottom gets a little clean. What a scam.

Whirlpool Gas Range WFG540H0es - Purchased 2 months ago. After 2 weeks there was a spill. The black burner caps are powder coated. After cooling we washed it with dish detergent & a sponge. The powder coating came off. Called the company. They replaced burner caps. Last week there was a spill and it stained the burner bases which are powder coated in a silver color. We tried 409 cleaner, Windex, dish detergent with a sponge. Could NOT get the stain out started removing powder coating. Called the company they ONLY guarantee cosmetic appearance 30 days. They wanted $139.00 for a new set of burner bases. I am going to go back to Lowes & see if we can return this Whirlpool range.

I bought on 14/4/12 a Model-205 Orchid Wine refrigerator. The defrost knob was replaced by service last month, as it was not working. For the past four days, there are lots of water formation on the freezer door and vegetables are getting spoiled due to water formation. I request them to replace the refrigerator.

Whirlpool side by side - What more can I say? A 1-year warranty is all Whirlpool can afford to give anyone since the compressor broke a few months after. They are paying for parts, but we are paying $300 for labor to fix a $1,200 fridge... in addition to having to be without it for a month, losing defrosted food, etc. Fortunately, the dealer gave us a loaner.

Cleans average compared to previous dishwashers. Does not dry well even on high heat dry. Cycle takes about two hours and I have to run it during the day because it is too loud. The price was good, but I wish I would have bought a little higher grade.

Whirlpool Gold appliances are junk!!! Our dishwasher just stopped working one day. It was about 2 years old. We tried all the troubleshooting ideas we found on the internet. Nothing worked. I had a 13 Year old working dishwasher when I bought this one. Sure wish I had left well enough alone. I think there should be a class action lawsuit against Whirlpool. I had also purchased a new electric range... It is constantly giving me an error message when I try to use the oven. We have to flip the breaker and that sometimes helps. I bought 4 of the Gold appliances... I’m holding my breath on the other 2. I thought I had done a good job researching before I bought. I remodeled my kitchen. It turns out that a company that I believed was reputable and worthy of my business are not.

They are good washers but they are overpriced. They have way too many functions for doing laundry. I know everyone wants their washer to do it all but the machines just can’t. There is no washing machine in the world that can sense a stain and pinpoint it and remove it.

The trim on the front the my Whirlpool electric range has rubbed off. This is where the knobs for the burners are located. It was replaced once during the Whirlpool 1 year warranty (so it obviously happened with the first year!) and again during the second year we have had it. We have an extended warranty but have been told that it is not covered. It is ecstatically unacceptable. We have not used any type of harsh cleansers on it - simply a sponge to remove any spills yet it keeps on disappearing. I strongly recommend against buying any range from Whirlpool as it is quite obvious that they do not stand behind their products beyond the first year.

The washer buttons stopped responding after 19 months. Lid lock sensor didn’t work. Replaced control board because new sensor did not fix it. Went bad again after a week. I have to replace it. I think 1 year warranties are not enough for a major appliance.

We have had our catalytic oven explode into millions of hot pieces again for the 3rd time. Contacting them they sold me an extended warranty which Im trying to cancel and have been trying since 30th Mar to contact on ALL of their lines. It is permanently on hold or engaged. This company should be avoided at all costs. If you work for this disgusting company DONT!! You will be out of work soon! It is unbelievable how bad they are at responding to their (now ex) customers. What the hell are we in the EU for when a supposed UK co is Italian and they never respond (AKA 1940). Ludicrous! Incompetent! Stupid! Totally without comprehension. Do NOT buy ANY INDESIT or HOTPOINT products EVER!!! They are dangerous and you will NOT get any help to put them right.

I apparently am one of the lucky ones to have an electric water heater. My unit started giving me failure codes during the Christmas holidays. Each time it would fail, I would get a different failure code indicating the upper element, the lower element, and a sensor failure. After testing all 3 of these components, it was determined to be a controller issue. After speaking with Chris on the phone, he overnighted a new controller to me. I installed the new controller and had no more failures. Hot showers for New Years! Thank you Chris.

I took a load out of my Cabrio washer and put it directly into the dryer. They had been on high spin. Now they are on medium heat. The clothes seem warm whenever I open the dryer to see if they are dry. They are warm... but not dry. There are no towels or jeans in the load either. T-shirts, underwear, etc. Ridiculous! The last load was jeans. Also 3 hours, but I thought maybe I had it on the wrong cycle. Now I think its the machine, not me.

I bought a brand new washer from Home Depot, Whirlpool 4.3 cu High Efficiency Top Load Washer to be exact. It hasnt even been 90 days and it started to make the loud, horrible noise so we had someone come and look at it. Apparently the transmission blew and the oil leaked all over my tile floor. I work full time and I do laundry only on the weekends and there is only two people living in the house so you can imagine we do not use it that much. I went to Home Depot first and since it was past 30 days we had to called Whirlpool direct. The customer service is horrible. I thought since the transmission blew, they would replace the entire machine since that is the brain of it. NOPE! They said to replace the entire machine and give us a new one, it would have to break 3 times. Are you kidding me? They did not offer to reimburse the tile damage or the amount of money I had to spend at the laundromat. Not to mention its been over a week and the guy still has not come out and fixed the transmission. It would not be a big deal to me if the hose broke or something simple, but imagine if you bought a BRAND NEW car and the transmission broke 60 days after you bought it. You would take it back to get a new car. The customer service line could not care less about the issue. I spent over 2 grand in appliances from Whirlpool and I will never buy their product again because of the customer service and the fact they did not want to make the situation right. I just bought the machine brand new for a reason!

My NEW Machine Top loader HUGE drum. Have problems with clothes not looking like they’ve even been washed, Spun so hard they are twisted all to heck. And white stuff - my oxy powder maybe? Not dissolved. My old machine was a Kenmore 30 yrs old. Thought I’d be able to trust whirlpool but not sure. Am I missing something in the loading process. Seems to read something bout not Covering the knob on the bottom. Is this true?

This dishwasher does not clean the dishes. Having said that most of the dishes are too oversized for the small capacity. Perhaps the fact that this is such an old dishwasher. I’m not sure but none of the dishes get washed. About the only thing that works is the dryer heater. Sorry to say, I’m not happy with this dishwasher and wouldn’t recommend it to anyone.

A disaster from start to finish. I would give it zero stars if possible. Purchased from Home Depot online in September, 2020. The first delivery was scheduled for October 11, 2020 at 7am on a Sunday. I spent hours on the phone trying to get the time changed. I was assured it would take place later. That didnt happen. The delivery service Temco called at 6:30a and refused to come back later. I had to make a new appointment. A week later they delivered the dishwasher, left it on the porch, refused to uncrate it or bring it inside the house, refused to haul away the old machine and stole the Dishwasher parts kit that I had paid for which delayed installing the dishwasher. After the machine was installed I discovered the machine did not come with a manual. I was told I had to download and print the manual.When I complained that I should not have to use my paper and ink to print a users manual after paying $800 for a dishwasher. I was promised a check to offset my costs. I was supposed to get a credit for my inconvenience but that never happened either. The first time I ran the machine using the one hour cycle water was all over the machine and I had to dry inside. I was told that I had to use a longer wash cycle so I did the second time. After 4 hours of washing, the glasses had a film on them, even though I rinse the dishes before putting them in the machine the dishes had some debris on them and water had still collected on the top of the glasses.Whirlpool sent a repair company out and the technician said motor pump and display control were faulty and it would probably be cheaper to replace the dishwasher rather than repair it. I was told I would get an email the next day telling me what would happen. I never got the email. During the week I called Whirlpool and Home Depot many times to complain about the faulty dishwasher, stolen parts and the promised refunds for my inconvenience as well as having to print the manual. Calling Whirlpool or Home Depot customer care will take hours and gets you nowhere. A week after the repair person came out I called the repair company to request a report as to what had been done and was told that they were coming back out the following Monday to fix the machine again. Monday, The repair technician came out and replaced the control panel but not the pump. The machine wont heat up to dry the dishes--the heating coil wasnt even warm after being on for 8 min. I am supposed to be contacted again for a 3rd visit!! I have a dishwasher that is faulty (read lemon) and Home Depot wont allow me to return it because their return policy is 48 hours after delivery. Whirlpool refuses to replace it unless the technician says it cant be fixed. Obviously, that will never happen. I should have repaired my old dishwasher rather than waste my money on this horrible machine. Whirlpool used to make fine products but those days are over. How does running a dishwasher for four hours saving energy? My old over 10 year old Whirlpool dishwasher was perfect until the pump broke. The dishes were always clean, dry and came out of the machine hot and sanitized. I am so disappointed in both Whirlpool and Home Depot.

The dishwasher is quiet and seems to clean most all of the dishes even when there is dried on food remnants. Multiple cycles that allow for light, medium and heavy cleaning. Also the ability for air dry and minimum use of water. The size is appropriate for normal amount of dishes, pots, pans, etc. Stainless steel front with most of the controls hidden. I have always had good luck with Whirlpool products, with this dishwasher continuing with being a quality product for the amount of money spent.

We bought a 20.5 cubic ft Whirlpool refrigerator. 2 months later it started cutting off, and on in a constant repeated cycle then run normal for a while. We had 2 Whirlpool repair appointments. The first guy said he couldnt come fix it unless it was acting up while he was here which was a intermittent issue. Refrigerators dont perform on cue. The 2nd guy came out after the first guy messed around long enough for the warranty to expire. We went ahead, and replaced the startup relay (most common problem). He replaced the control board, and wire harness. He said if that didnt fix it he didnt know what else to do. 2 hours after he left the fridge was right back to doing the same thing. He failed to report back to Whirlpool that the fridge couldnt be repaired. We contacted customer service, and their resolution was to get another repairman to come out, and replace the control board which had already been replaced. In the end they bailed on us, and left us stuck with a broke refrigerator, and we had to buy a new one ourselves. I might add it was not a Whirlpool. They spent $471 trying to fix a broken fridge, and wanted to send another repairman (another $100) to fix a $629 refrigerator how does that make any sense. It was a very disappointing experience, and Whirlpool should be ashamed.

Whirlpool duet steam front loader - The rubber gasket ripped about a year ago and cost over $400 to have a tech come and repair. Then the water level switch got bad and cost another couple hundred. A year later, the rubber gasket ripped again. What a junk washer. I am ready for a lawsuit because Whirlpool will not replace it.

Purchased Feb 2013 - worked okay until one month ago. Now stalls in the drain and spin cycle. The rotation of the drum sounds awful, makes a loud grinding noise. I tried doing the diagnostic reset of holding the Temp button in for 3 sec, release, 3 sec more but that didnt work. Also, I have noticed clothes are DRY after the Wash cycle! Managed to interrupt the wash and unlock the lid and was very disappointed. This is not a good quality piece of equipment. This seems to be a very common problem. How unfortunate.

My mother has had this stove (Whirlpool Accubake) about 3 years. She does little cooking. On June 24, 2015, herself clean activated, probably for a few days, this is normally 850 degrees. She is 84, does nothing with this stove, certainly not knowing how to hit the clean button and HOLD the Start button for 3 seconds... this caused the stove to billow smoke out of the oven and encompass her entire home. No fire, but was caught in time. The fire department had to pry open the door as it would not unlock.

We purchased the Whirlpool Cabrio washer and dryer duet exclusive to Lowe’s in June 2011. I was immediately dissatisfied and went to Lowe’s. They told me I only had 7 days to return it. They dispatched a service man and he said it was working as it was intended to but I would never be satisfied. If I had dirty clothes from farming, construction, or mining, I should forget about it.” The washer is an eco-friendly model and all the clothes do not get wet. It wrings them out very tight and everything needs to be dried or ironed to get rid of the wrinkles. After 6 visits and lots of stress, I am returning the washer to Lowe’s and they will replace it with a different model. It definitely will not be a Whirlpool. I am very disappointed in the service and response I received from Lowes.

We have these appliances in our apartment. Its a gas range with a microwave over the hood. We did have the microwave replace a year ago, we have been here for 5.5 years. Its a good stove, we would consider buying one for ourselves.

I rent a condo unit and hardly use the microwave. It is nice to have. Never had one over the stove and it came with the unit, so I gave mine away. After living here for 3 years I am now moving to another city 5 hours away. I noticed the other day when I went to melt butter for popcorn, the door crack, which I noticed the second year we lived here, has gotten worse. Not just worse, but the handle looks like one pull and its completely broken. My landlord expects us to pay for this. I am reading and I see that its from the heat from the stove, which is also a Whirlpool product, is to blame, not the user. How is this right, how is this fair?? When we move we will have to buy a new microwave, that will sit once again on my beautiful microwave cabinet and I promise, it WILL NOT be a Whirlpool!!!

This is a freezer on top unit. Purchased in 2015, unit quit cooling, started making a roaring noise. Called local technician, he added 2 oz of Freon, said he has seen many of these same unit losing Freon. Technician said line that goes to compressor is copper and hooks up to aluminum line before attaching to compressor. This is leak point for freon; no way to know when the leak started, but freon almost gone and cost to pressure check for source of leak is costly and probably would not repair problem. Got 6 yrs out of it and I am replacing with another brand. Will never buy Whirlpool again. Should have got 10-12 yrs of use. Do not buy this unit. Wrote Whirlpool first, but no help. Indicated this could be a problem with these units but no recall so I am on my own. Out $900 for a new refrigerator. Big hassle. Unit no good.

I was pleased with the look and performance on my dishwasher. It did sometimes leave some food particles, but, overall it did a good job. I really dont remember the model since it has been a few years since I had it.

We purchase Whirlpool fridge less than a year ago. Its still under guaranteed. 2 months ago we notice the fridge part heating up and food was going off. I went back to the shop where we purchase the fridge. They said we had to contact Whirlpool direct so we did had to wait 3 weeks for someone to come and look at it. Fridge is not repairable. Fella who came out did not report back to Whirlpool. I was waiting and waiting to hear word. I rang to see what was the story on it and eventually they said O we will exchanged your fridge and we will ring you on delivery date. Now Im over 2 month waiting on a fridge. Whirlpool is a joke. The company should be put out of business for what they do to honest people buying their stuff, and people who are in the same boat as me should go to the high court and sue them for all the stress they put people through. Shame on you Whirlpool. Disgrace.

We purchased a front loader Duet in August of 2011. It is now January 2013 and we had to have a service person come out. We did not buy the extended warranty because a washer should last longer than 1 year 5 months, but not ours! We need to have the drum replaced at $600. Are you kidding me! I will never buy another Whirlpool product.

I have automatic Whirlpool washing machine since 3 1/2 years I am using. Now 2 times electronic board came problem so how many times can change like this? Why they are manufacturing if they cannot solve this problems? Should not sell in the market. This all not coming free and need to struggle. Whirlpool products all very bad appliances.

We have had this washer for a year and the longest it has run before breaking down is 3 weeks. Since it takes longer than that to get a repairman out to look at it and another 2 to 4 weeks to get parts, it has run less than half of the time we have owned it. This thing is a hunk of junk. Dont ever consider purchasing one of these lemons.

We bought a refrigerator Model# WSF26C2 EXB last June 2012, and it broke down! Our one-year manufacturer warranty did not cover for any food loss. We would not recommend Whirlpool refrigerator to anyone. We called at 12:30 pm and they could not send anybody out to repair the refrigerator until the following day. Bottom line is, there is no compensation with Whirlpool.

We purchased Whirlpool sports model on 2/1/2011. We faced a problem with the motor in a month’s time. The service man told that there are fluctuations in the power so it went wrong. They replaced it after 15-20 days’ time. We also complained that it’s making noise and then he told that we should keep it on the stand. We did so, even then, it’s still noisy. Now about 3 weeks back, suddenly it stopped working during the wash. I never overloaded the washing machine. We complained to the dealer. The mechanic came and told that we had to replace some parts and he will get in a couple of days, but he never turned up. When we contacted the dealer, he said that the parts were unavailable and he will send them in a couple of days. I am fed up of that answer. We could have purchased IFB instead of this.

I purchased a Whirlpool oven and stove from hhgregg. The refrigerator is at best OK. The stovetop is easily scratched and looks horrendous after just a few months. Cooking controls are far too high for slow cooking. Customer service is terrible. Avoid, purchase another brand. You will be much more satisfied.

I have a whirlpool water heater. This is the third or 4th time that the upper sensor failure code has come on. Our water heater turns off all the time and we have to fire it back up. In the past few months, it has started pouring water out from the long tube on the side of it anytime we turn it on for more then 10 minutes. The last time we called a plumber, I was trying to get a quote on a tankless water heater. Ive been so fed up with ours and I thought that would be a better route to go. The plumber explained the negative sides to a tankless water heater and explained that our water heater was a really nice, really expensive and fairly newer model. I told him that I had just gotten it about four years ago. He said he could just fix that one. So after looking at it, he acted as if he didnt know what an upper sensor was and told me it was under warranty and that I should call for the parts. Every time we have called for the parts, they send the same box thing on the front of the heater and every time, it doesnt fix it for long before it says the same thing. And now, like I said, the water heater has now added the problem of pouring water out of it. I need help. I dont know what to do. Im tired of not knowing if Ill have hot water or if the water heater is going to pour out water. Im pregnant and worried that if we cant get this fixed Ill continue to have this problem along with having a baby to take care of. Please help.

I have a Whirlpool Gold Series dishwasher. I would recommend this dishwasher. It is large enough to hold dirty dishes for a family of four. It is a little loud but not that bothersome. It is stainless steel but I don’t have a lot of fingerprint smears and stains.

We bought our new Cabrio (washer and dryer) in the fall. Within 2 weeks, I realized what a piece of crap these machines are. They simply do not clean the clothes. I have complained to the store where we purchased them, and I was told there is nothing they could do as the machines are performing as designed? Im waiting for a class action suit to join to get rid of this junk. Curt

I bought my fridge 6 years ago. 13 months after purchase I had to replace the compressor. Last month I had to replace the water drip pan. Now the fridge is knocking and hissing again and warm inside. Compressor needs to be replaced. I contacted Whirlpool and they said 6 years is old for an appliance. Seriously!?? What about 13 months when the compressor went? They obviously dont stand behind their products. They are unable to admit I got a dud. Im so disappointed and frustrated. Stay clear!!!

This microwave came with the apartment. Its the 2nd one we have had. The first one failed in our 3rd year here. We dont use all the functions, but what we have used, it works fine. Would I purchase this brand, no. I would choose GE, or Panasonic.

The machine has an infinite water level setting, an agitator which I feel cleans clothes better, separate settings for water temperature for both wash and rinse cycles, and the ability to soak prior to washing by just leaving the lid up. You can add bleach and fabric softener to dispensers that will add to the tub at the time needed. My machine has been a really good one.

Bought a Whirlpool french door fridge in July of 2019, The icemaker began pouring water out of it and the temperature of the fridge would not go below 50 degrees. Contacted Whirlpool and the technician says it will be over $800 in parts plus service to repair. Now I must go 24 days without a fridge in the middle of summer until they can get the parts. How does a 10 month old fridge need all of the parts replaced except the condenser in that short of time? Whirlpool should be held accountable for manufacturing the defective fridge and leaving their customers stranded.

I purchased this washer 3 years ago. At year 2, I had to replace the RPS part. The codes that appear represent 2 different issues as well: one being the RPS part and also for the control panel. In less than 1 year since this replacement, it is broken again! The clothes do not get very clean. You cant soak whites in hot water and bleach (it drains after 5 minutes if you stop it). You have to use the bulky setting to get enough water to actually wash your clothes. If you get too much detergent, your clothes comes out crunchy feeling even with the extra rinse.I thought this Whirlpool product would be great since my 22 year old dishwasher is a Whirlpool and still works but as the old saying goes... They dont make them to last like they used to. To say this washer is a POS Lemon is an understatement! I also have the companion dryer and it is starting to have problems including the door latch breaking into pieces. I will never purchase another Whirlpool product again! I have been told that Kenmore and Maytag are also under the Whirlpool umbrella so Im not sure what I will buy next. My recommendation: DO NOT BUY THESE PRODUCTS!!!

This is a good looking, inexpensive stove/oven. Stove top has four burners. I liked the split grates on the stove top. Its easier to remove and clean. I do not like the rubber seal on the oven door. I am used to the heavier duty seals on most oven doors.

16 months after purchase, the machine starts displaying F71 codes, 6 weeks later F70. After calling Whirlpool customer service number on the User Manual, we were told that the washer was out of warranty and there was nothing that Whirlpool was going to do for us. I have a reasonable expectation that a brand new $800 washing machine will operate for many, many, trouble free years, but finding an electronic failure that has been estimated at $400 to repair, 16 months after purchase, is simply and obviously unacceptable. This is clearly a defect in design and/or manufacturing.

Just bought Whirlpool refrigerator, stove, and dishwasher. So far, the icemaker doesnt work and so I have no water or ice in the fridge. After four visits from Lowes it is still not resolved. Going on since 11/16/18. After waiting three weeks, the dishwasher came, and lo and behold - it doesnt work. Now I have to wait for one to be ordered! TAKE A WORD OF ADVICE - WHIRLPOOL ISNT WHAT IT USED TO BE. DONT BUY IT!

I did not purchase the washer (Cabrio Top Load Clothes Washer) but inherited it in a home sale. Never had a non agitator. I was excited for this new washer. After a week I knew why they left it! My clothes did not seem clean; stains were still on them, when I used the delicate cycle a pair of pants went in folded and came out folded!!! I also would have to redistribute the clothes every time I had a load that was larger than five pieces, because it would stop. I would actually have to take clothes out and spin what was remaining then put those in the dryer and put the other clothes back in and spin those again. I was told I needed to use OxiClean on top of my normal detergent in order to get my clothes clean. Never again will I purchase a Whirlpool. Just bought an LG; fingers crossed.

The only model number I can find is W10484489A.... Do NOT buy this machine. It is pathetic!! This machine cannot handle more than 2 bath towels at a time!! It will just keep trying to spin, yet NOT spinning, then when you stop it, there is no choice to just spin again, you have to rinse and spin!! Unbelievable.... takes a whole evening to do one load of towels!!! (actually a whole evening to do 2 towels) I hate it!!! Not to mention, whatever they designed between the tub and the door, a rubber whatever it is, is nothing but a catch for disgusting bacteria and slime. Considering the amount of wash I DONT DO, this is unacceptable, even though I have bought and used the new washing machine washing stuff!!! Honestly.... had a Maytag Neptune before this machine..... that is the way to go folks, pay a little more, but way more satisfied. Cleaned like a gem, unlike this whirlpool, cleaning is at best mediocre!! Unfortunately, I broke it, asking it to wash huge 120 in round table cloths for my business, and heavy chair covers..... Had I have know.... cant even wash 2 towels in this new Whirlpool machine!! It is heading to the curb with all its disgusting places you have to clean, I will pay someone to take it away, seriously cost me a ton of money in re-spinning (or yeah, and re- rinsing, cause you cant just spin something), would have been better to fix my MAYTAG!!! I hate Whirlpool!! Do not buy one!!

Purchased this washer new 2015 for use in our cabin. Now 4 years later with very little use the motor has seized. Washer is useless. What happened to 20 years of almost daily use and still runs great. This washer is a very poor quality washer and has now failed. Please save your money and buy a different brand.

In 2002, I purchased an EE3Z50RD055V 50 gal. Whirlpool hot water heater. Recently several solder joints on the computer module became unsoldered so I cleaned the joints and resoldered them. But several months later another joint became unsoldered so I thought Id just purchase a new module. I called 1-877-817-6750, explained the problem to the young lady. She informed me that they would ship me a new one overnight. I asked her how much this would cost and she told me there would be no charge as it had a lifetime warranty. SURPRISE! Thats what I call customer service! A few years ago, I purchased a Whirlpool Duet front load washer and dryer. Now Im twice as glad that I did. My wife and I LOVE the Duet.

I am pleased with the steel tub, the ability to do an extra rinse and spin and especially the choices of water level that it determines by the size of the load. Its ability save water use. I would repurchase the top loader again. My clothes come out looking wonderful especially the whites and I do not use bleach. It does not get the mold or mildew odor that my last machine would get due to the rubber or plastic made tub. I love it.

Bought a Whirlpool French door refrigerator in March 2014 and have had to have it serviced 4 times now - all for the same issue. We get frost in the refrigerator (not the freezer, the refrigerator). The same parts keep being replaced but they are all defective. This last time the service tech said he contacted Whirlpool and they had a redesigned part that should take care of it. Within 3 days of the new part being installed the frost is back. The other issue is the loud noise of the compressor. We have had multiple Whirlpool products through the years, but this is the last.

I bought this top loading, low water machine 1.5 years ago, $500.00, did not buy extended warranty, expect major appliance to last at least 5 years. Motherboard is out, will not spin, will cost at least 200 to $300 to get it fixed! Selling on Craigslist for 50. So sad. Will never buy whirlpool again, waste of hard earned money!

Doesnt wash clothes properly - often some items of clothing just dont get wet. After 3 years the whole main bearing in it failed, causing unbelievable noise and constant overload faults. All Whirlpool top load washers have this critical design fault where water leaks into the main bearing (the bearing is an unsealed type with a cheap grommet seal) and then after a year or 2 the bearing starts to cease and the machine overloads itself trying to operate. Replacing the bearing means pulling the whole machine apart - and with a cheap press-fit bearing like this, special tools are needed and it will never operate smoothly again anyhow. In any case in 2 years, the faulty bearing seal design will let water destroy the bearing again. Effectively it is not repairable. Sounds like class action to me. So, it became an $1000 paperweight and I bought a new Samsung unit. I assume the Koreans know how to design bearings and seals...

I am having the very same problem with my french door stainless steel Whirlpool gold refrigerator. Water pooling in the bottom of freezer, freezing into a solid sheet and then leaking onto the floor. It is less than 2 years old. Apparently, this is a significant defect in this problem seeing how so many people are having the same problem with the same fridge. Has anyone reported to BBB? Im thinking class action lawsuit. Im getting ready to have to repair my kitchen floors as a result of this defect. I will be talking to my brother-in-law attorney about this and will post his response/recommendation. Whirlpool should stand behind their product and make this right.

I bought my Whirlpool top loading washing machine 07-22-14. I so dislike the locking mechanism and will be certain to never, ever buy a machine with that feature again. It is so irritating to try to add something but cant because its locked so have to hold the button 3 seconds to unlock and start all over. If there was any way to get around it I would. I will stay away from Whirlpool products in the future and will be sure to check the next time I buy that the lid of the washer can be lifted when not spinning. Also, I do not like that it sticks on rinse sometimes and the only way to end a cycle is to hold the button and then start over with much wasted water.

Whirlpool Refrigerator Freezer WRF560SEYB01. Purchased the Whirlpool Refrigerator Freezer in 2012 at Sears. Ran okay for 2 years. Bottom freezer door came off the track. Called Sears. Sent out repairman for $200 to replace the door. He did not check the ice buildup on back of freezer. Next problem, severe ice buildup, loud noise. Used hair dryer to melt ice and took the blower fan out of freezer. Solid ice on all the blowing fans and found a chunk of solid ice. Freezer no longer made the noise until the ice built up again. Now, it continues to build up and we have to use the hair dryer every two weeks. A refrigerator should last at least 10 years. This model doesnt even warrant a rating of any kind.

We purchased this washer on 2008-04-27. It ran okay until a few months ago when it began making strange intermittent noises. This is now happening more and more often. I reviewed a lot of websites and see that this is a common occurrence for Whirlpool Cabrio washers, and Whirlpool will not stand behind it and make it right. Im going to write them a letter mirroring what Im saying here, and remind them that other appliances in my house are coming due for replacements or upgrades. Whirlpool and its affiliates will not be part of those upgrades going forward. I have no patience or tolerance for expensive **, which is what they put out here. I will have to purchase a replacement washer since this seems to have two major areas of failure, both extremely expensive to repair. I might check out Roper and see what they have--its apparently very well rated by the folks that work on these things.

On December 21, it became clear that I needed to replace our 13-year old Rheem water heater. We decided to buy one from Lowes, 36 miles away and have a handy man install it. He installed the new Whirlpool 50 gal gas water heater with a 12-year warranty on Friday, the 22nd, but could not get it to stay lit. He called Whirlpool to troubleshoot. They said it could be one of two parts and that they would ship the parts on the Monday after Christmas. He asked who would install and they recommended a local plumber. He called that plumber but they indicated they did not do Whirlpool warranty work and would have to charge.On Monday, I called Whirlpool and was assured the parts would be shipped that day for overnight delivery. I confronted them about the local plumber not doing their warranty work so they set up an appointment with a company called A&E for Wednesday morning. On Tuesday morning, I called Whirlpool to get the tracking number on the parts and was told that they did not get shipped on Monday as promised but would be shipped that day, arriving by the end of the day Wednesday, too late for the appointment for installation.By Tuesday night, my wife got on this site and was appalled to read the numerous identical complaints. I decided that Wednesday morning that I would hire a plumber to remove the Whirlpool and install another so we would not have a lifetime of problems from Whirlpool. The plumber installed a different water heater. It started right up and we have had no problems since. I got an R or RA number from Whirlpool which I think they only gave me because the parts had not arrived on time and I returned the piece of ** to Lowes for a refund. Lowes has a seven-day return policy of these.

We bought our Whirlpool Cabrio 7 years ago and it was great at first. I have not had any trouble with it ripping clothing. The clothes are clean. Its constantly breaking down. First it was the drain pump. Then the main computer board went! I called Whirlpool and of course the lady says its not covered. I had back up though. Google is amazing! I asked why this wasnt a recall as all over the web, people had this same problem. I pushed and pushed and she put me on hold. Came back to say it was in fact covered. What? Really? What changed your mind? She wasnt allowed to tell me. Supposedly had something to do with the date of manufacture. So okay, they send the repair guy out, its fixed. Now tonight, the lid locks and nothing happens! This repair was about 6 months ago. Grrrrr. Its been one thing after another with this hunk of expensive junk. When I buy an appliance I expect it to be problem free for far longer than this. I am not getting a code or anything, just dead air. So frustrating with three kids not being able to do laundry when I need it randomly :( Has anyone else had this problem? The lid locks, then does nothing. I unplugged it, pressed off and restarted it. Changed settings. Nothing is working.

Despite my claim being submitted within the first 4 months of purchase, Whirlpool would not assist in solving our issue. We purchased all major appliances from Whirlpool, to furnish our new home in August 2021. All appliances were white. The top of our gas range began discolouring immediately following the first use. The inside of the four corners immediately began to ware due to heat. I figured Id have time to put my claim in, and thought to see if it got worse. Once I finally had time to deal with the issue, I contacted them only to find out that we only had 30 days from the date of purchase (of which included 3 months of waiting for the products to arrive) to claim the issue, given that it was considered Cosmetic. Easy fix, since theyd simply have to change the top of the stove, but Whirlpool denied our claim. Do not purchase this product, unless youre looking for a sub-standard product and customer service.

We purchased a new Whirlpool water heater April 2013 at Lowes and every 3-4 months the pilot would go out. My husband would simply re-light the heater, I guess he didnt think it was a big deal. However, in September 2014 the water heaters pilot went out and would not re-light, so I contacted Whirlpool about the warranty. It took 4 telephone calls (two of which involved a plumber, per Whirlpools request), and several days of cold showers for an authorization code to purchase a $8 part (thermo coupler). The hassles that Whirlpool put me through, no one should have to endure. Who ever heard of a technician telling you that they have to talk to the plumber, when you call them to explain a problem with your water heater, such as, the pilot will not stay lit and the plumber said it is the coupler (I couldnt remember the whole name of the part, but surely they should have understood what was wrong). Secondly, providing a plumber (unless youre married to one) to converse with them involves more money. Now I have a plumber at my house so I call Whirlpool and this technician insists that the plumber perform a test on thermo coupler to make sure that it was faulty before she gave the authorization for a new one. Yet again, when I called to Whirlpool with the plumber, while I was voicing my problems in resolving the issue of my water heater with this technician, and she just hung-up on me. So as not to be defeated and having already invested in the expense of the plumber, I called Whirlpool again and requested a manager. The technician asked if she could help and I informed her of my previous encounters. She apologized and took my information to have a manager to call me later; however, she did give me the authorization code for the thermo coupler without delay. When I went to purchase the part, I didnt have the old part (as trade; the plumber hadnt removed it), so I paid for it out-of pocket, to return the old part later.

We purchased this dishwasher (Gold Dishwasher WDF60SADB) because of its low 49-decibel rating. It goes over 60 decibels regularly and occasionally up to 70 during operation (not including drain noises which cannot be controlled by the dishwasher). We used a tablet app to confirm. Decibels are not linear, they are exponential. 70 decibels is what your average shower or dishwasher sounds like. 50 is about as quiet as a refrigerator. You have to talk over this dishwasher. And yes there was a big price difference between it and Whirlpools next loudest rated washer.Whirlpools customer service says they will not replace or repair based on sound ever, only for functional failure. Bottom line, dont pay any attention to Whirlpool sound ratings. They dont stand by them and do not consider gross overages a defect. Fortunately the retailer (Lowes) does stand by what they sell and will trade for any other machine by any other manufacturer. We have only good things to say about Lowes in this process. This machine arrived Wednesday, and we pick a replacement Sunday. It will not be a Whirlpool. I will never buy a Whirlpool anything again. We said it will do X but we dont care if a brand new one wont is no way to do business.

10 years, no problems with our 25 cubic foot french door Whirlpool refrigerator. Ice maker is a solid performer, with nary an issue. Temperature controls work flawlessly. The black frame looks great in our kitchen with espresso color cabinets.

I purchased this Maytag clothes washer in 2007. So far Ive had to purchase and replace the front door 2 times. The current one now needs replacing. The plastic near the hinges disintegrates after about 2 years. This appears to be a manufacturing design defect. I have requested from Whirlpool to send me a replacement door for my washer. The part number is 34001178. The model number is MAH2400AWW. The Serial number is 14060452LE.I have spoke to four different levels of employees at Whirlpool after escalating the service request. Each time they have told me they are unable to send a replacement door to me, stating that the product is out of warranty. I realize that the washer is out of warranty but I believe this problem is a design flaw. The plastic near the top door hinge breaks down and cracks after 2 years of normal use. The last person I spoke with Michael (would not provide me with a last name) said to write to the Whirlpool corporate office with my complaint.

I have a two year old Whirlpool dishwasher. The soap dispenser cover broke shortly after the warranty ran out. It cost 100.00 for repairs. A year later, it broke again. I sent a letter and the part to the CEO of Whirlpool. They sent a repairmen to fix it free of charge. When you have a problem with a Whirlpool product go to the head of the company. If they get enough calls they will make better parts. Call 1-269-759-6919. Write a letter, return request receipt. It takes a little effort, but it helps a lot of people.

If I fix this washer I will have been on 3 motherboards in the 5 years I have owned this machine. That is inexcusable and indicative of crap quality control and manufacturing process. I should not have to replace the control board at these intervals or, within 5 years, at all. I will never touch another Whirlpool appliance again.

What happened to the Whirlpool Corporation that we grew up with? I purchased a Cabrio Washer on 8-29-11. Here it is, 4-24-13 and the transmission is shot. Two loads of clothes were ruined and sensors went bad. All in all, over $500 to repair it. I called the customer service line, what a joke - bad product and worse customer service. Not even and Im sorry. Well it is out from under warranty and when I buy something, I research it first, she said. Wow! Thanks Reena for all your care and concern. I dont know if Ill ever buy Whirlpool again.

Purchased this washer in 2009 from Lowes, believing the hype that it was efficient. Since we only needed a Washer at the time, we overpaid (it is more cost effective when you buy both washer and dryer). So we paid $1000.00 for this machine (we purchased the stand as well). After the 1st year, there seemed to be a significant decrease in how fast the washer spun, as the clothes were coming out wetter. I didnt pay much attention, but 2 years later, the machine has a weird problem where it couldnt complete the cycle, and by this time, every time it Spun, the noise was louder and louder.I contact Whirlpool, placed a service call and the Technician came out. $225.00 later, there was a hose that was pinched that was sending a wrong signal to the washer. He fixed that and told me I should get a contract on the machine through Whirlpool since I seemed to be having problems. I purchased the contract, for $300.00, and 2 1/2 weeks later placed another service call, as the noise from the machine was happening every time I did laundry. The service guy came out, indicated that it seemed to be the Agitator, and that he would need to order parts, and that they had a SPECIALIST who only does this type of repair, since they have many! He also indicated that the hose may have crimped due to the movement of the entire agitator!Well, after not hearing from ANYONE for 2 weeks, I called the repair company who told me WHIRLPOOL was supposed to call and let me know that they would NOT fix the machine, as the parts cost more than the Washer, which is now valued at $500.00! No one from WHIRLPOOL EVER CALLED, and I cant understand how a $1000.00 Washing machine touted to be so efficient and environmentally friendly has been THROWN OUT after 3 years!!! And now I am out the $225.00 repair, have no washing machine, $1000.00 down the drain (and I forgot to mention a year later we bought the matching WHIRLPOOL DRYER and OVERPAID) and now have to purchase another machine, which I assure you WONT BE WHIRLPOOL! As most of us have experienced, WASHING MACHINES last for many years! The washer I had before this was over 20 years!!!! So much for efficient and environmentally friendly... The only thing GREEN about this machine is how much of my $$$ has gone to Whirlpool!

I have the model FG1H5040T3NOV water heater and had found this message board. I called the number posted by Chris with American Water Heater and provided them with my serial number. They shipped me the replacement assembly next day and after about an hour, I had it installed and working again. Im not too happy with the fact that it failed, but it does appear they have their act together in getting the replacement parts distributed.Based on the discussion with the person on the phone, my only real gripe is this: the cause of the component failure was potentially caused by a dirty-flame trap that supposedly needs to be cleaned regularly. Since the trap is underneath the water heater and is in no way really accessible, relying on people to see the fine print in the manual (which hardly anyone reads) isnt sufficient. At an absolute minimum, a very clear and apparent sticker should be included on all water heaters indicating this needs to be cleaned and a clear description of how to clean it properly to prevent this sort of unnecessary headache in the future.

I have enjoyed my stove for 16 yrs, it is very reliable and easy to use. The heating elements work well and heats up quickly. During this time I have not had any repair done. The areas of improvement that needs to be implemented is the inter glass that is installed at the front looking into the oven. In order to clean you have to take the front door off which is very difficult to put back together.

I know that appliances are made to be disposable, but throwing away a $40 toaster after 18 months is easier to live with than throwing away a $350-$400 dishwasher. We bought a new dishwasher at Lowes on October 15, 2015. It is now May 11, 2016. The manufacturers warranty was for a year. It has been about a year and half since it was installed. Not very long for an appliance that one would assume would last at least 5-10 years. When we called Whirlpool to see about a repair visit, we were told that the trip to the house would cost $105, and the parts could go as high as $250-$300. So if you weigh the original price to the repair price, having it repaired is not rational, but neither is throwing away a dishwasher thats almost new. Its still clean inside. No soap residue or anything in the tub. In the past, by the time we were in the market for a new dishwasher, our old dishwasher looked like it had been through the war. It just breaks my heart to know that a company is so slipshod at making appliances that they wear out in less than two years. There doesnt seem to be any recourse but to dump a perfectly good, relatively new dishwasher in the landfill. We are leaving a very big footprint by doing this.

Moved into a house with a 2009 Gold Series Dishwasher model GU2475XTVY0. It has never worked since we moved in 3 years ago, always left dishes musty and poorly cleaned. We basically used it as a rinse/dry and pre-washed everything by hand. Even then it would mold up frequently and required manual cleaning. Total piece of junk, but looked really nice, stainless finish. Yeah.Latest chapter is it completely stopped working. Called a tech out for the usual $80+. His advice: this is a total lemon, and has been from the start. Not worth repairing. So Whirlpool, is this the standard you have now? 5-6 years for a dishwasher life cycle? Noted that my fridge is a matching 2009 Gold series, it has also had several problems with keeping a steady temp and has gone through 2 control boards at a hefty fee each. I guess Im done with Whirlpool, running out of appliance brands to blacklist here...