So the reviews for the Bravos MCT online were pretty decent. We purchased our set from Lowes. However, the clothes dont turn over. I watched as long as I could (getting frustrated the longer I watched) to see how the clothes were going to get turned over and washed. All they did was get rubbed on the bottom of the pile where those agitator fins are. But they never got a good flipping so that the top of the pile was washed. I only had 4 normal size towels in there. So it isnt like I had too many clothes.So I called Maytag to tell them what I was observing and the gentlemen explained that it was counter-intuitive technology and that it seems like they wont come clean but he promised me by the time the load was done they would be clean. Yet - they did not come clean! The dirt on the towel was still there on the top of the load with dog hair. NOT TO MENTION SUDS!! Im so disappointed because the burden is on me to either take this set back or deal with it. Buyer beware - if you look at this machine and ask yourself how in the world will the clothes get clean - you are asking a great question! They dont!!

I loved my first Maytag combo unit and when that quit I bought another Maytag. The Neptune is a front load washer. I immediately noticed the door gasket getting moldy. I contacted Maytag whose response was leave the door open. Well, I did that and not only did I still get mold, but the light burned out. I recently started having trouble - the water doesnt drain and the clothes are still wet. Rather than have it repaired, I elected to buy a new washer/dryer unit. I would NEVER again have a front load washer and certainly not Maytag.

We purchased a Maytag front-load washer and dryer in October 2010. In March 2011, all bearings and the drum needed replacement. In July 2011, the pump needed service and now in Sept 2011, we were told a new drum and bearings are needed again. The washer is still under warranty by Maytag. We contacted Maytag to ask for an exchange or a refund but we were told that it wasnt possible.

I had to rate at least a one star because there isn’t a negative to rate. We bought the Maytag mvwb955fc1. First off it doesn’t clean our clothes. I can not get stains out or whites bright. I don’t feel it uses enough water. I put a full load in and it only fills up less than half with water. I try half loads and still not clean. It’s always shutting off when I wash sheets. Indicating it’s off balance. Today I started it before work and the lid exploded. I don’t think I want to even replace it at all. This could have seriously hurt someone. Do not buy this washing machine. The dryer is great so far. I wish I could post a photo to show you all.

I thought washers are supposed to last 10 years or something. 3 years and I have to replace it. I dont know who Im more dissatisfied with - Maytag or Direct Appliance where I purchased it. Just thought I would rant and warn others about this brand. The computer died so it doesnt know what cycle its on. Repair guy said its unfixable. ARGH!

Maytag used to make a great laundry machine. The barrel of the Bravos XL machine is very deep, and it is difficult to reach the bottom of the machine to get clothes out. My biggest complaint is that the clothes dont get clean; there is not enough water filling the machine to clean the clothes. The clothes get wet, but there is no agitator, and the water isnt deep enough to suspend the dirt and wash it away, even on the deep wash setting. There is also a lot of lint left on the clothes that cant rinse off. Why is the barrel of the machine so deep if it only fills up 1/6 of the height? I had great hopes, but I really regret buying it.

I have had it since 2011 and still works as good as it did back then. I love it. Hope it helps people decide when they go shopping for a dryer. I have a dog so I have to keep her clean so I wash a lot of her bedding and she sheds a lot. She also sleeps on the with me so that other bedding that I put for her on my bed between her clothes and mine which I do separate. The dryer works a lot and it is still going strong.

We purchased our range in May of 2012. It is now November 2014 and the stove has had three brains, three ignitors in the oven and one ignitor in the back of the stove. When I set it to bake at 350 degrees, the oven heats up and I put the food in the oven. When I go to check the food, I find the oven stone cold and the brain is still displaying 350 degrees. According to Home Depot Warranty department, if the oven has been fixed three times for the same problem, then the unit is considered a LEMON. Ok, what about the three brains? What about the three ignitors? The ignitor in the back of the stove controls the oven as well. SEVEN times for a technician to come out and fix my LEMON stove is ridiculous. California has lemon laws. I will file suit against Home Depot, Whirlpool, A&E and Quality Appliance if this stove is not replaced within the next seven days. IT IS A LEMON! I have lost way too much food in this oven because I dont know when it shuts off.

My washer is great. It get the job done. Have no agitator so I can wash 2 comforters. I really like Maytag Heavy Duty. Can get the job done right the first time. Self clean itself also. Also it is a efficiency.

It leaves white stuff all over everything. You have to rewash or rinse black clothes at least twice. We have to clean the washer frequently or the clothes smell like mildew. I chose Maytag because I thought they were the best. Apparently, I was wrong and it was a mistake buying this.

My new fridge iced over top to bottom. It started making horrible noise then ice maker stopped working. Called MY repairman. Thats when I found out about all the ice. He told me to thaw out and hed be back. It thawed out and then freezer went out. ALL my freaking meats and frozen food had to be thrown out. Now water keeps Flowing out on my NEW tile! Called my repairman back. He came back then informed me it was junk! He said several other customers having same issue. My daughter has the same refrigerator and it broke down just like mine! My repairman also said a big issue with your junk was you used parts from other brands to fix!After reading all these complaints I can see no sense in calling to get it repaired. Its obvious we are all having the same issue. Maybe someone from your ** company could check them out. I dont have the money to buy another fridge! My 85 year old uncle with Alzheimers lives with me and I dont want him to slip on that water and hurt himself! I think all of these complaints need to go to BBB. Thats my next step. I believe you need to recall this junk or give us our money back! I need you to respond or Im going on blast to let everyone know how you treat your customers.

I purchased a new Maytag washer (Model# MVWC565FWO) from LOWES 18 months ago and the paint is bubbling on the inside of the door. Neither Lowes nor Maytag would do a thing. We have spend many $1000s at Lowes and considering the replacement cost is only $126 for a new door I can see Lowes following Sears for their lack of customer service and diplomacy in matters like these.

Purchased less than a year ago, Machine stopped working. Approved service company says no error codes visible must be ok. Machine still does not work month later, service again does not show up for call, following month same. Its still in warranty but they claim it is fine. Error code disappear right after popping-up no storage of error codes.. I had to buy small washer to manage home. Really bad choice of product. Will not use this brand again.

I bought a Maytag washer 3 years ago. Maytag gave me a number for one of their warranty service repair shops in my area. The first repair service doesnt even respond to my calls. The second repair service is a total ripoff. So in summary, Im stuck with a 3 year old washer that has a broken drive assembly that the warranty wont cover.

Works great, quiet, cleans better than the others in my opinion, have had many others and they never impressed me like this brand does! I think this one gives you your money's worth and you don't have to look no further for a dishwasher again, and is top quality and hardly breaks down as well.

I bought a Maytag Bravos from Home Depot back for around $1000 in Nov. 07. After 3 yrs, the whole tub assembly had to be replaced but I had bought a warranty so that was taken care of but it was out of service for about 2 months while I waited for parts. Now every time I use it, I get the OL on the control panel and it wont spin without getting out of control and stopping. Washers in the past have lasted me at least 15 yrs and cost less than half that much. I will never buy another Maytag ever. This is what happens when companies merge and quality is no longer important. I think the stock market ruins companies. Im currently looking for the best quality, large capacity washer on the market. I will pay more for quality but thats what I thought last time.

Perfectly great, cleans anything, not terribly quiet, but results are more than satisfactory. Good water pressure, cleans every nook and cranny, things come out spotless. I do not have anything else to compare, but I think the size is fine, I can put a lot of stuff in it. Controls in front at top, easy to use, clean appearance. Even though my dishwasher is 13 years old, I have not had any trouble with it. The top racks are strong and hold a good bit of glasses, cups and bowls. I have put baking pans, cookware, grates, and a lot of other stuff in to wash and it all came out clean.

I hate my new Maytag washer and wish I had never purchased it. Theres no way to control the water level in it, and on sensor mode, the clothes are barely wet and rubbing against each other creating wear. Things come out with soap stains and twisted up so tight that I dont believe water got close enough to the dirt to carry it away. Dont waste your money.

I have had and worked on many washing machines over the years. The worst design and complete failure of parts to easily align in Maytag front end washers is nothing short of staggering. Creating a tension wire to wrap a rubber seal that requires Hercules to install and easily tears the rubber is beyond ridiculous. Avoid front end Maytag washing machines like the plague since they may cause it given the mold and growth from excessive moisture when the seals tear.

I purchased a topload washer two years ago and the plastic lid has been replaced 4 times because it cracks at the hinges. It is obviously a manufacturers defect that Maytag refuses to admit. They come up with excuses blaming the consumer instead of their bad design.

Please let me know if there is a class action suit. My lower freezer froze within a year, now 2 years later same problem. Im all in, this is clearly a design defect that we are all paying for. I would have bought something else. Ridiculous product.

I found this washing machine reliable for over 10 years. I paid more for this brand but it was worth the extra cost. I found this washing machine Simple to use. I would recommend this washing machine.

All I can say is what a mistake. Had a front loader that always smelled and had mold around rubber gasket in door. So, wanted a top loader this time after old GE died. Unbelievable, not enough water to clean clothing. Clothing comes out with some dry spots. And the worse thing is washing black items, tiny particles on black pants, shirts, etc. Think is lint not soap but not sure. You have to rub all over the clothing to try and remove. This washer is 8 months old and I have cleaned it with baking soda and vinegar mixture thinking this would help, it doesnt. The spin cycle sounds like a rocket ship taking off. Lots of banging noises during operation also. I have invested a lot of money thinking Maytag is rated high. It is a pretty grey color with glass top. Well I was fooled, not only the saying looks arent everything for people but its true for washing machines. I have gotten multiple mail from co. wanting me to get extended warranty. Think I will, usually dont, cause I think it wont be reliable. Wish I had my washer from the 70s and 80s. Plain old wringer that got things clean. Just put black pants in dryer on very low heat taken out damp cause I dont dry a lot of my clothing. This seems to have helped to remove stains (soap)/ lint. but, talk about wrinkles, oh boy, this machine has that spin cycle going 100 miles a minute. And if you pick a lower spin speed things come out wet. I actually can say I hate this Maytag Bravo. Things dont come out clean, wrinkles beyond control, very loud. Please folks check out your sites on the internet before buying Maytag.

After less than two years the commercial washer we purchased from Lowe’s died. A repairman came out after a week and said it potentially needs a new control unit or computer. The control unit is on back order and we’ve been without a washer for a total of three weeks. The situation still remains unresolved and I’m regretting not going back to Samsung. After 9 years with a Samsung washer, it died and Samsung refunded the full price of the washer. It was a poor choice to choose American. :(

I purchased a Maytag refrigerator 4.3 years ago. Model #NSD2572VEW01 side-by-side. Came home to find water on floor. Called for service at a local company. Tried several new parts, only to find out I had a bad compressor. Part cost $358.30 + labor charge which couldnt be estimated because of difficulty with installation. Called Maytag for help, was told FIVE times, Sorry, nothing we can do to help you. Have never had any other appliance in my life except Maytag. NEVER had a problem with anything before. Have washer, dryer, fridge, stove, microwave, and dishwasher. Found the answer to be unacceptable!!!

I bought all new Maytag appliances for a new house built 2 years ago. The oven fan, while in warranty, began coming on in the middle of the night. It would turn on, cancel, began not working, and then the ticking noise began. Maytag sent 5 different service people out, sometimes without the part. We are afraid to use it now and have turned off the breaker for it. Now, it is turning itself back on again. Maytag says we must now pay for any repairs/service calls as it is out of warranty. It was not out of warranty when all these troubles began.I called Maytag customer service today and could not have talked to a less customer friendly person. She didnt care that it was in warranty when the trouble began. It is out now and is our problem. There is no one else but her we can talk to about it. She is the decision maker. What experiences has anyone had with trying to call the president of Whirlpool, or filing a small claims court action? Any help is appreciated. Who is going to cook our Thanksgiving turkey?

Hello, My recently purchased dishwasher has leaked water within less than half an hour of the fifth time to be used and showed error: F8E4, dishwasher model and SN are: Model: MDB4949SKZ. Serial # : FA3003347. Registered: 09/11/2021, Ive been calling Home Depot who in turn asked the installer to check the connection, and the latter advised and reported its a manufacturer issue. And calling Maytag for several times but no response or action. On-line service scheduling of Maytag is not working!!! And the live chat is not helping, as well. Now my dishwasher is not working since more than two weeks, knowing that it has been installed only a month ago.

I have a Maytag Bravo washer which I purchased from Brubaker Appliances in Lancaster, PA four years ago. I also purchased from them an extended 5-year warranty. I have this installed on 2nd floor with a drain and a drain pan The drain pump got a hole in it and leaked water all the way down to the basement, over $6,000 in damage. The drain pan and drain didnt work because the Maytag has a noise barrier on the bottom and when that was soaked with water, it sealed off the drain pipe. Also, when I contacted repair at Brubakers, they replaced the drain pump but then informed me that it wasnt covered because penny got in there and that is neglect. $332 later, I was told that the extended warranty covered everything and also no one will take responsibility for installing the washer so that the drain pipe could be blocked. I will never purchase a Maytag again or anything from Brubaker Appliances.

We bought a Maytag dishwasher March 2012 and the unit wouldnt turn on October 2013 - 6 months after the warranty ended. We called their service department and they told us to unplug the dishwasher or turn off the circuit breaker. We did so and the unit still would not turn on. We called a repairman who advised us that the touch pad was not working. The cost with parts and labor would be close to $300 which was more than half the original price. We repaired it and I sent all the papers with a letter to the consumer department and today I got a call advising us that they would not do anything. Do you think I have any further recourse? If not, I will never buy a Maytag product again and will advise anyone within a listening area as to how we were treated.

Bought a new Maytag dishwasher in July 2013. In December it quit working and the problem was the control panel. The service tech knew automatically what the problem was when he arrived. It is now May 2014 and the control panel has gone out again. Contacted Maytag and was told they will extend the warranty another six months from the original warranty. After reading that this has been offered to others with mixed results I have my doubts on whether it will be honored. This is our last Maytag appliance.

I have owned my Maytag washer for approximately five years. Ive always used the recommended detergent and religiously used the tabs to clean the machine when it was required. I have never abused the machine by overloading it, using too much detergent, etc. It is now coming up with an LF code. There is no one in this area who does repairs and if I do find someone Im sure theyll want some exorbitant amount to come all the way out to the boonies to give an estimate and the repairs Im sure will be hefty. I take very good care of all my appliances and expected this machine to last much longer.

Washer purchased in May 2013 last month it stopped completing the drain and spin cycle and cloth stayed wet. To have the machine repaired, we would have to replace the control panel. The cost of replacing the control panel plus the service call was 76% of the cost of buying a brand new machine. As such we are disposing of the machine and will be purchasing a competitive product.

Maytag Bravo washer and dryer delivered 2 days ago.My complaint is with the washer. I didnt know it was HE and that it requires special detergent! I didnt know the lid locks! I didnt know when I push the hot water button, the machine mixes in cold water! Complicated, delicate machine and not user-friendly. I dont expect the washer to last long.

Maytag dishwasher model MDBH949AWW - I purchased a dishwasher thinking I was buying the best (laugh is on me). The date of purchase was 1/18/10, the control panel was replaced on 5-25-11 at no charge. On 10-15-12, the control panel failed again so I was forced to hand wash an entire load of dirty dishes. I used the dishwasher once a week. I am debating if it is worth it to repair it or replace it, in light of the fact that it could go out again the next year. Wish I had found this website before I made the purchase.

We purchased a Maytag gas range, only to have the paint wash off the front trim of the oven door. The digital panel went out in the second year of use and is apparently expensive to replace. After going through reviews by other owners and discussions with repairmen, it was determined that these panels only last about a year and are defective. This problem is extensive with Maytag. My brother was a repairman for them and dropped them due to poor quality of workmanship in appliances and their dishonest approach to warranties. I should have known better. Dont ever buy Maytag!!!

I purchased the Maytag double-oven gas range, Model MGT8775XS, in 2013. The quality of this double-oven stove cannot be understated. Performance? Terrible. Reliability? Awful. My experience was shocking because when I was a kid, Maytag was the ideal for quality and reliability. Those days are over. When delivered in 2013, the ovens did not work. Heating went to 200 degrees and stopped. During the next three years, we had this Maytag stove repaired four times. The most recent repair was in October 2016. A new regulator and igniter cost us $360. Four weeks later you guessed it the ovens stopped working yet again. We sent the Maytag stove to the recycle dump. Its far more valuable as scrap metal.

I also have a Maytag Quiet Series 300 dishwasher. The front panel has stopped working. It was a horrible dishwasher from the beginning. The dishes were streaky on the top rack. And I had to replace the rollers after just over a year. The upper rack has rust on it. The Maytag double ovens I bought at the same time had to be replaced within a year, as the racks damaged the porcelain interior. I also wish I had found your site before my purchases. My husband is not working now. So, I guess we will be washing dishes the old fashioned way.

We purchased a Maytag refrigerator (freezer on the bottom) in August 2012. In 2014 we had to have the freezer repaired (defrost drain) which cost $153. This month, July 2015, we had to have the refrigerator repaired for another $293. The problem with the refrigerator the repairman told us is the control board (p/n W10503278). He stated that they didnt make the first board very well and hes been replacing this part quite frequently for customers. I only spent $799 on the refrigerator and I already have $446 into it. That is half of what I paid for it! I wouldnt recommend Maytag to anybody!

I purchased the Maytag Bravos washer and dryer in September 2010, before moving to Washington. After a few months, the washer broke and had to have a repairman out twice to fix. It never would wash a blanket without stopping with error messages. He told these were notorious for problems. Now our dryer is leaking and not drying. I checked the vent hose and water and some wet lent are inside. In moving the dryer, I can hear a piece rattling around inside. From research and other posts, it sounds like its a broken pulley system inside. Maytag is junk. Customer service is terrible! I bought this unit during a veterans day sale at Lowes, using my veteran discount. Obviously, Maytag has no problem ripping off veterans or anyone else based on their horrible customer service. I will be actively posting as many negative online posts and videos about my experience on every forum and veteran site I can. They are horrible! Stay away from Maytag!

Purchased this washer at the end of August and it was delivered the first week of September. On September 27th the rubber seal around the door somehow got tangled in with a shirt and was ripped off (absolutely no idea how that even could have happened) and spilled water all over the floor. I called Maytag on Sept 27 and they had a tech out here by October 2nd which was great. However, even though I had told them the problem and that the rubber seal was damaged the tech didnt bring one when he came. I had to call them last week to find out what was going on - they had the tech call me and he said that the part had just shipped and he should have it by next week - Today, I had to call again as there was no follow-up from the tech and was told that hopefully the tech will come on October 21st once he gets the part as he hasnt received it yet. I regret purchasing Maytag, as I had heard they had better service (local techs/parts warehouses) than LG or Samsung but that doesnt appear to be the case. 3 Weeks to repair a $1400 washer that I used for about 4 weeks is unacceptable. On top of the inconvenience Ive had to spend $40+ dollars a week at a laundry mat, plus waste my time. One star service.

Tried various cycles and I hear water going in but don’t see any water. How does this wash clothes. I want to see water and soap clean the clothes. If I want dry cleaning I will bring the clothes to the dry cleaner. Never again will I buy a high efficiency washer. My clothes do not come out clean!

I purchased a refrigerator 9 years ago and the ice maker stopped working. When the repairman took it out there was plastic peeling from the ice mold. It cost $261.11 to have the ice maker replaced and the ice maker he replaced it with has the plastic on the ice mold. He said that GEs ice makers do not have the plastic coating but Maytags still do. I called Maytag and spoke to a supervisor and they said that there was nothing that they could do. I am filing this complaint because I feel that consumer need to be aware that they are ingesting plastic that is in their ice. I feel that Maytag should compensate me for the faulty part and also eliminate the plastic coating from their ice maker. This issue is impacting many other consumers and they need to issue a recall on the ice maker and replace it for free for other consumers.

We purchased Maytag dishwasher model #MDBH989AW53 in January 2010. June of 2012 the control panel died. Luckily, we had the extended warranty. The service company came and replaced the panel. 3 weeks ago, the panel died again! The service company replaced the panel again. Today I got home and the dishwasher is completely dead! I am so furious!!! At this point, I may just have to bite the bullet and buy a brand new machine. This should NEVER happen to an appliance that is so new! What a laugh regarding the Maytag quality! It is the WORST I have ever seen in my life! Stay away from Maytag!!!! Buyer beware!!!!

Purchased a Maytag Bravos XL less than 3 years ago Model MVWB725BW0. We have had several repair calls. From reading complaints from others, I have the same: clothes balloon, clothes rip, dark clothes have a scum on them, even a blanket goes off balance and it is hard to start the cycle. It goes off balance all the time, makes a squeaky sound when agitating and the housekeeper can never figure out what cycle to run the clothes on because they always go off balance, there is a loud vibration, etc. The last repair call was for an actual leak on the floor! The appliance company charged us $95 for the service call, did nothing, and told us the parts would be more expensive than a new washing machine. Went to Home Depot today and purchased an LG washer and dryer for over $1500. I am not even going to try to recoup anything from Maytag because this is the second Maytag that I have had a bad experience with and didnt learn a lesson in the first place. Junk. :(

I purchased a Maytag dishwasher 15 months ago and was told the control panel is bad. It would cost me $120 to have someone look at it. I might as well buy a new one by the time the parts are added. I called Maytag and they said that there was nothing they could do for me since I was three months past my warranty. Meanwhile, I see all of these complaints about the same problem and Im wondering why there has not been a recall on this. What does it take for that to happen? I will never purchase a Maytag again! Their customer service leaves a lot to be desired. All they do is apologize like its programmed in their heads. This feels like a fraud!

The dishes need to be washed off to be sure they will be clean. It holds a lot of dishes. You can put it on a short wash or long one. Leaves water on base of glasses sometimes. Holds moisture. Heavy wash, normal wash, light wash, rinse only, auto clean, delay 1-9, heated dry, sanitize, tough scrub, extra rinse. Regular size 24. Beige color. Electronic buttons. Maytag Quiet Series 200: I do not like the racks for putting dishes in. Otherwise it holds a lot. It does not clean dishes if you do not rinse them off first. If you run the dishwasher immediately after putting dishes in it will clean them off. Sometimes it leaves water standing. Even with what I have said I really like this dishwasher. We have had the dishwasher a long time. We use it at least 2 times a week.

I have now owned my highly efficient and low-cost to operate washing machine for 6 years. It is a top loader and uses HC detergents.This means the washer needs minimal soap to clean the clothes. I especially appreciate the different types of loads such as deep cleaning or regular cleaning. The washer has sensors that evaluate the size of the load and thus only utilize the amount of water necessary. I really like the quietness and being able to get the very best wash because the washer does exactly what it needs to do. It has more than been the appliance that I had hoped for. Love it! It maintains itself.

Purchase of what we thought was high quality Maytag dishwasher. Paid $600 and $250 to get it installed, which was really just to take out the old dishwasher we wish now we had kept, and plug in the new one. After 2 years, repairs needed to replace the control panel and key pad must be replaced, cost $340 plus labor. We will never buy Maytag again. Called their hotline, 800-877-6777. They cannot offer any help. Called the co. we bought it from, a Maytag dealer, Haleys Maytag of Antigonish, Nova Scotia. They too offered nothing except to sell us parts... control panel and key pad. Called lawyer who has class action suit now against Maytag, Eppsteiner & Florica. They are not representing customers who live in Canada, only U.S.My recommendation to Maytag dealer who only sells Maytags, Haleys Maytag of Antigonish, Nova Scotia, find another company to represent. Maytag is a real loser. Never again purchase a Maytag, and I told 10 people who will tell 10 people... who will tell 10 people. Our model number... same as all of yours... the loser MDB6709AWW1. Dont waste your money buying this overpriced dishwasher that will then require you to spend more money every 2 years on a Control panel and Key pad that are defective from the factory.

I bought this after having a Frigidaire for 40 years and was immediately disappointed upon installation. This OVEN, not a range, was smaller inside and a lot of new pans would not fit! I have replaced the burners and the bulb wiring several times. Would not buy another one!

Dishwasher is around two-three years old and it will not start or drain. From what I can tell on the internet, this touch-pad control panel has been an ongoing problem for Maytag. Will try to fix myself, and if I cant fix it, I will buy a new dishwasher but not a Maytag. By the way, my washer and dryer both went out this year - five years old and both are Maytags. Stay away from this brand.

Maytag dishwasher model MDB4949SDE3: This dishwasher is the biggest POS that I have ever owned in 40 years. The first one would never turn on and fill with water and after it finally did it leaked on my new floor. Waited 10 days to have it replaced. The dishwasher cycle is 2.5 - 3.5 hours and the dishes come out dirty. The top rack is not adjustable to wash odd things. I feel that these dishwashers need to be replaced.

This appears to be a common, known, well publicized problem - freezer drain clogs and needs to be either changed or repaired with a fix, a free replacement part for the drain seal. Easy to install, takes 15 minutes. HOWEVER Maytag will not give you the part!! In order to take advantage of Maytags correction for a well known, chronic, manufacturer defect, you must engage an authorized service person for hundreds of dollars and wasted vacation time waiting at home for them to show up. Unlike any other product, recall this one is not free. My kitchen is full of Maytag products; dishwasher (not so good), range and a refrigerator that had to be replace when the compressor went out after six years. However this is the last straw, Ive learned my lesson, seen the light, THIS IS THE LAST MAYTAG PRODUCT I WILL EVER BUY.

We have a Maxima washer which is about two years old. The tub around the barrel cracked and flooded the laundry room. The repair person said it would cost more to fix than replace. Very unsatisfied. We are trying to deal with the company but not optimistic.

Our less than five yr old washer finally died. It had been making awful sounds. Started in only very small loads but then started in bigger loads too. It finally stopped altogether. Model number MVWC400XW4. I would NOT recommend this washer.

CWG3600AAS13 - I purchased this advertised as Double Oven. It is NOT - its an oven w/ broiler. The oven shuts off completely during cooking time and comes back on approx. 2-3 mins. This takes place often and loses heat. I have to adjust cooking times and oven temp to make up for the loss. This also happens when broiling. Needless to say it takes MUCH longer to broil anything. When I notified Maytag of this, they responded with it is an open door broiler. Are they serious? I have 2 dogs and 11 grandchildren - burn factor anyone? (P.S. It did not change anything.)

I am angry that Maytag puts out a washer that hasnt been through quality control. The computer panel is a piece of **, and is not worth $1.00. Do not buy this washer. Shame on Maytag.

Purchased a Maytag Dishwasher (Model MDB7749SBBO), total with tax $590.34 on 3/31/13. It wasnt a cheaper model, had stainless interior. Owning it after a 1-1/2 year, the Control Panel went bad. Maytag offered me for $267 for repairs and 1 yr warranty. Why thats about half the price I paid. My personal repairman told me the cost would be around $200 to replace the control panel. Why I could get a more inexpensive model for $300 and still get a year warranty. Very disappointed in Maytag quality of their product.

It’s washing day today, so I’m angry, frustrated and livid to do it in my Maytag machines. I’m 72 years old and been doing this for 53 years. It’s not a job you love to do but you do it. I finally get to be able to afford whatever machines I want, so what do I do, buy Maytag. They are beautiful, see through top load, and see through dryer. So finally I get to use them, what a letdown. I don’t understand how they can put these machines on the market. Unbelievable! Also very expensive. The sensor for the water level is way off. It starts washing with hardly no water covering the clothes so this is where I put it on pause and add buckets of water to wet at least the clothing. I did a test to see how the clothes moved inside when washing. It was a load of white towels and I put in a bright green face cloth to see how it moved around in there. Well what a surprise, it stayed on top and moved about 3 inches to the right. That’s all it did. You don’t call that washing, I call that soaking! Terrible washer! I could go on and on but I’m getting too upset. Now for the dryer, the sensors don’t work right so what I do is use the timer and the temperature buttons only. Sometimes clothes gets stuck under the lint basket and by the time the buzzer tells me the load is finished drying, it is so twisted that it’s wrinkled forever. It has ruined a beautiful tablecloth of mine. I can’t sell these machines because I would feel very bad to pass them to someone else…Maytag does but not me. Because of my age I won’t be getting new machines probably, I’m stuck with them, but I would advise anyone shopping for a new washer and dryer, go out there and see what they have, come back home and look for reviews which I did not. Bad mistake! Note: I searched everywhere to write this review to Maytag on their website, none to be found!

Did not know of the lawsuit or recall. Now I have to buy a new washer after fixing it out of pocket and mad that cant get part of the settlement. Not ever going to buy Maytag again!!

I love my Maytag. It does a good job, however, it takes almost an hour to run one load. Also, if you have a heavy load, it doesn’t spin long enough so your clothes are dripping when you take them out.

Maytag Commercial # MVWB765FW0: My husband and I wanted to get rid of our GE front load. It was horrible. Even constant cleaning and leaving the door open all the time, our clothes still smelled like mildew and musty. My hubby wanted an LG and I said no way. As a little girl my mom had an old wringer washer and her first electric washer was a Maytag in the late 50s. She passed away in 2001 and in her lifetime she had 2 electric washing machines both were Maytags. They were so dependable and built to last so naturally I wanted a Maytag. Wrong! I am so disappointed. We purchased it in Sept of 2017 for $695. I was so excited the first time we used it. It was a little noisy, but living in the county and having a well we were glad it was an energy/water saver. The first couple of months it was so refreshing to have clothes that did not smell musty and mildewy. I noticed they were really wrinkled but I still iron anyway so it was not a big deal. However ironing over and over again on some items did not get rid of the wrinkles and the past 2 months I have been going thru lint rollers like crazy and it still does not come off. I have to use a slightly damp lint brush or go over the clothing with packing tape to get the lint off. It is horrible! I dont want my GE back but I dont want this one either! I wish I would have read reviews first and listened to my hubby. I wont ever have another Maytag and when this one goes I will certainly read reviews and go with something more dependable. Unfortunately for now we have wasted the money and it is ruining our clothes! I agree that we should all do the class action. There are just too many of us experiencing the same issues. Maytag should do right by the consumer! We have learned our lesson, review before you buy!

We had our kitchen redone by Home Depot in Sept. 2006. It was gutted and all was replaced: walls, heat windows, doors, lights, appliances. The Maytag refrigerator stopped working 7 years later. I feel an expensive appliance should last longer than that.

Bought a Maytag microwave model MMV4205DS and I too have had an issue with open/close door display. Just like other reviews Ive read it started out once in a while for the first year then began happening more often til it stopped working by the second year. I also read someone asking why there isnt a class action lawsuit? Good question. Way too many bad reviews on same issue. If I knew how and if we could start one then I would. Thought we could trust a company thats been around for so many years. Wish we had check into it more and I have learned from other products to do just that from now on. Have a backup microwave by GE from WalMart weve had for 10 yrs still working.

Within a year of purchasing this washing machine, I needed to schedule a repair service because the washer started making an unfamiliar noise. Repair Service shows up and refuses to touch my washer. The ink on the Serial and Model number (stick on label) inside the washing machine door has washed off. Sticker label in excellent shape, except all the ink has come off. If the Repair Serviceman cannot read the label, NO SERVICE FOR YOU. MY SAGA... Did you know that if your washer or dryer does not have a readable serial number on the machine, NO repair service will work on it. It does not matter if you have all the paperwork showing this information. If the original label is unreadable, no repair service will touch it because they will be fired. Maytag changes parts on a model all the time. The serial number is the ONLY way a serviceman can tell exactly what parts your washer was made with. Apparently the serial and model number label sticker was not printed with permanent ink. The Repair Service said the Serial and Model number ink washed off the label because the sticker was incorrectly put on the inside of the washer door at the bottom. But they were WRONG! Maytag shows online that is exactly where the serial and model number sticker is supposed to be located. So, I called Maytag to order a new serial number (stick on) label for our washer. I gave Maytag the information and I was told I would have the label in two weeks. Then I called back a week or so later to make sure the serial number was ordered and on the way. Maytag said there was a misunderstanding, and that they received my request on 6/17/15 and it was sent to the ONE AND ONLY GUY that makes replacement serial number tags and he was sent my request on 6/22/15. Maytag said it would take the one and only man quite some time to make the label (SINCE THERE IS ONLY ONE!!!) and I could expect to receive the replacement label in 4 to 6 weeks and they were sorry, but there was absolutely NOTHING they could do about it. So as my year old washer sits for over a month, Im going to the Laundromat each week. We should have received the new serial number on August 6, 2015. So it’s taken almost 2 months and my label is close to two weeks late. To date I have not received my serial number. I tried to use MAYTAG chat, dont bother, they said they couldnt help me. I needed to call in. So I emailed Maytag today for their support services to tell me WHEN I can expect to receive my new serial number label. I bought this through hhGregg. Check your Maytag washer. IF THE SERIAL NUMBER AND MODEL NUMBER LABEL ARE INSIDE THE DOOR, CHECK TO SEE IF THE INK IS COMING OFF THE MACHINE LABEL, and order a new one NOW if it is, or you will not be able to get your washer serviced. Do not put new label back on the inside of the washer door. This is just unbelievable.

If you are looking for the Maytag repairman he will be at my house Tues fixing my barely 1 yrs old dishwasher. This is ridiculous to pay this amount of money for the reputation that Maytag is known for or I will say was known for. $270.00 for a control panel. My last Maytag lasted over 30 yrs. Not made in the US - not built to last and this was told to me by the people that installed it so take it for what its worth. Look elsewhere. My last Maytag product.

If I could give this a 0-Star rating, I would! I cant believe Maytag would make such an awful washing machine! Within the first 2 weeks I called their service department because (in my opinion) the washer wasnt washing properly. It took over a month and several calls to get someone out to look at the washer & dryer. According to the technician, both machines were operating properly. Apparently the washer is designed to destroy clothing and bedding! The gentle cycle set on deep fill will add just enough water to get the clothing wet, then agitates for about 10 minutes, then it fills up, agitates for 3 more minutes and drains. During the 10 minute dry-run, I watch my clothes get destroyed! I have never seen anything like this! My sweaters are shredded, my tops are pilled up & in a garment bag this thing managed to destroy a sports bra! This machine has ripped my mattress cover in several places and pulled my sheets from excessive rubbing due to not enough water. And what is up with the slow fill? The technician informed me that the trickling water is also normal. If I could return this washer, I would! I will never buy another Maytag because my Bravos washer died after only 4 years, and this one is brutal!

As many other reviewers have mentioned there is a defective control panel in the Maytag Dishwasher series MDB 7749. I too purchased this model at Home Depot and did not buy the extended warranty. The serviceman indicated that this model is known for its defect yet Whirlpool who owns Maytag does not have it on its recall list. I wrote to the President twice in Sept. 2017 without the courtesy of a response and now learn that he retired effective Oct.1. Is there no-one to answer his emails or is it more likely they really dont care. Sears just dropped them and who knows where their new president will lead this company. Be aware that this model dishwasher is defective and they wont replace the control panel. Too bad as once Maytag before Whirlpool bought them out, was a good and honorable company.

I am, was, a loyal Maytag owner. The Bravos design, center hub, catches the clothes and rips the material. Customer service will only state damaged material is not warrantied. So I now have a washer that in addition to washing clothes rips them.

Purchased Maytag washer Centennial Econoserve washer. It was 2 years old Aug 2013. Washer stopped working Sept 16, 2013. Of course since it had Maytag name brand, I did not purchase extended warranty due to thinking it would at least last more than several years. I called Maytag/Whirlpool. They gave me name of authorized repair in our area. So far they have come out 2 times. $560.00 later, it is still not working and they have no answer as to how or what to do. We are now into $1300.00 between purchase and repairs and still no washer. We are retired hard working people and this is really a bad way to treat consumers. Maytag customer service could care less about the situation. They just say we should have purchased extended warranty.

Im extremely disappointed in this machine. I bought this machine after having my Kitchen Aid for 12 yrs. Just last month, the UL message came on. Had someone looked at it and noticed the bearing was loose. He fixed it, just today, it started doing the same thing again!!!!! Now it might be a suspension problem. Of course my warranty expired because I bought it in November 2012. Im never ever going to buy a Maytag washer again!!! Can someone help me to take my complaint to higher up?Thank you..

I owned a Maytag Bravos top loading washer for 8 years, and I loved it. It caught on fire while washing a load. Thank God I was home or it could have burned my house down. Just wanted to post this somewhere to issue a warning.

I purchased a Maytag dishwasher Model # MDB4949SDE1 from Home Depot April 30th 2015. This dishwasher does not clean the dishes no matter what cycle you use. After 4 hours and 29 minutes I open the dishwasher to find residue on my so-called clean dishes. Every time I use it I have to re-wash or rinse the dishes by hand before I can put them away.I have spoken with Maytag on several occasions concerning this matter. I have used every detergent on the market. Maytag says you have to use jetdry, and liquid detergent which I did and it made no difference. The latest suggestion was that the water from my water heater was not hot enough which is set on 140 degrees. The customer service rep. ask me how far the water heater is from the dishwasher and I replied approximately 14 foot. She suggested I turn the faucet to my sink on before I turn the dishwasher on so that the hot water is present as soon as I turn it on. This also did not work. They sent a kid out today that turn the dishwasher on for five minutes empty and said well everything seems to be working properly. I dont know what to tell you, yet there is soap residue in the bottom of the dishwasher right now. Do not purchase this dishwasher. It does not clean the dishes. It just uses power and water.

I purchased this machine (MVWB765FW0) because I had a good experiences with Maytag in the past. There is a manufacture defect in this particular machine. If I were you, I would not buy it. I’ve lost two sets of bedsheets and my wife had a dress that she loved that got ripped up at the bottom between the agitator and the base of the machine. Maytag knows about the problem and does not have a solution.

Purchased my Bravos June 2012. This is a horrible washer. It does not clean. It leaves a detergent scum line on clothing. My work clothes are visibly soiled and sometimes come out in a tangled mess. Maytag ignored a first complaint from my wife. I complained again today. Regardless what Maytag does, I will purchase another brand after research. We bought on Maytag’s reputation.

We bought the Maytag Bravos washer & dryer combo from box store. I wanted an extra large capacity washer to accommodate king sized bedding, and having fewer wash loads in general. Cons: 1 - This machine is not energy efficient when each wash load takes 1:30 to 1:50 each load. 2 - The detergent/fabric softener/oxi dispensers are a joke. Water dumps into every compartment at once. And if there’s still detergent left by the rinse cycle, well you get the picture.3 - The “Bedding” setting is the only one which will provide enough water in the tub to get anything wet. Since there isn’t any type of agitator the clothing/bedding just floats on the surface in dirty perfumed water. 4 - With any of the other settings the water level is so low it doesn’t always get everything wet so items are not being washed properly. At most maybe 2 pairs of jeans or just a few t-shirts can be washed on the “Normal” or “Power Wash” settings. 5 - Because there isn’t an agitator, clothing gets knotted up. Dress shirts, dress pants, jeans, towels, you name it, everything comes out of the washer in a knotted mess.The Bravos XL Dryer: My only complaint with the dryer is that it allows a good amount of lint to pass through into the machine. Then it’s difficult to get any type of lint brush into the vent area to remove the lint. Dampened lint in the machine can make clothing smell musty and nasty. I had to call a service to remove lint from the dryer & ducting because of the odor lingering from the inside the dryer.

I love my washer. I have had it for 13 yrs and has only needed repair once. My complaint is the gasket on the tub has black mold that grows on it. I have cleaned it with bleach, bathroom cleaner, alcohol, but it always comes back. What can I do to prevent illness from mold?

This Maytag is about 7 years old now, at least, and is still running strong. The one thing I do miss, though, is the lint collector basket that used to be on GE washers Ive had in the past. Kleenexes have a sneaky way to getting into the laundry and picking out the remnants is a royal pain! The lint basket on the GE would save me that task.

Purchased our Maytag Centennial Washer Model MVWC400XW4 2 years and 5 months ago; guess we are luckier than most; it has now failed in the spin cycle, high pitch, high volume whine, sounds like it is about to explode. Needless to say is out of warranty; and too expensive on our limited income to have a technician repair. I will hope to make the repairs myself; nothing to lose at this point; and from reading the countless negative reviews about this product; should be as many countless repair suggestions on YouTube. Obviously if Maytag would stand behind/up for their product as they claim they do; I and many others would not have these issues. My wife and I for sure will never buy another Maytag product until Maytag resolves the issue, which if my calculations are correct will be never. My advice is simple, do not buy Maytag products.

In July 2006, we purchased a Neptune Washer. The only problem we had with it is it does NOT spin the water out of the clothes after the wash cycle. This has been going on for about 4 years. In February 2012, we had a service person to examine the washer. According to the service person, there is nothing wrong with the washer. He said to put in clothing of the same type: All towels, all jeans, all pillowcases, etc. This is not the real world. This cost me a service call with no solution. On June 10, I called Maytag on my issues. They have no recalls or issues with this washer. They recommended another service call which I refused. I even offered the washer free of charge to the person I was talking to, but did not get a response. Never again will I purchase a product from this company.

My wife & I purchased our Maytag dishwasher model # MDBH979SAB1 on 3/8/13 from homedepot.com. Approximately 24.5 months later our dishwasher experienced control panel light button malfunctions similar in description to the many other consumer complaints on this & other forums. I would like to share some additional information based on my research about this issue and possible fix. The source of Whirlpools control panel issue is design related. The issue is caused from moisture which induces oxidation on the Flexible Printed Circuit (FPC) cable that is integrated with the control panel and connects via connector to the electronic control box. The issue usually manifests itself on the cable just where it bends coming out of the touch membrane panel.The oxidization of the FPC cable eventually creates electronic shorts or opens between the parallel traces thus causing the panel control lighted function problem which disables the dishwasher from being used. The cable, since integrated with the control panel, is not a separate replaceable part. In order to repair, the Whirlpool diagnostic action is to replace the entire control panel. I quickly learned after doing some online research about Whirlpools control panel issue that it extends back to at least 2011 with control panel part # W10475784 and corresponding or like PNs of this design. The number of control panels sold of this design by various online appliance part centers coincide with the high number of reported like control panel failures.In just 2015 alone so far, the sales for this control panel have been in the hundreds. This indicates that Whirlpool continues to replace defectively designed control panels upon failure with defectively designed control panels. There was also a class action lawsuit filed against Whirlpool in the state of California on May 6th, 2013 for the control panel issue. The filed lawsuit is public & the whole document is available online as a pdf file. Unfortunately, Judge **, granted Stipulation to Dismiss Case with prejudice 74 on 5/23/14. I was unable to find out any details as to why the case was dismissed. I did not call Whirlpool about my control panel issue, instead I handled all correspondence through Email to them at WHIRLPOOL_CUSTOMEREXPERIENCE@WHIRLPOOL. COM.My initial correspondence included all the facts about this issue & that I did not wish to have their warranty coverage/period explained to me for I understood them, the problem was a quality issue, and just basically wanted to know what they were going to do or have been doing about resolution. The email correspondence with them got me nowhere. They initially replied back with all the form niceties like We apologize, We understand your frustration, & We value you as a customer, but denied every knowing about such control panel issue, regurgitated their warranty policy & period and were unwilling to resolve anything. In their last reply they stated how unfortunate it was that customers only take the time to provide negative feedback!! This is just bad business, and though I would not like to think it, but the control panel issue may have been by marketing design.Please keep in mind that Whirlpool manufactures appliances under at least 15 different name brands including Maytag, Kenmore, Admiral Kirkland, KitchenAid, Roper, Speed Queen to name a few. All is not lost, being an electronics engineer I looked into the do it yourself fix. If you are not comfortable in doing this, you may be able to find someone to help. I was able to repair mine by carefully scraping off the oxidation from the FPC cable (will appear brown in color) & encapsulating it with high density 100% dampening silicon (non-caulk type) to protect it from moisture & withstand heat. There can be other ways of protecting it from moisture instead of silicon, just make sure it can withstand heat, wont become brittle, & that it may not cause potential damage to the cable itself.My repair has worked for about 4 weeks now, & shows no sign of oxidizing. The problem may be more severe if the oxidation has actually opened or broke one or more of the small cable traces. Do not attempt to solder this cable! Its way too thin & will only make matters worse. An open can be carefully bridged with a conductive glue or ink thats on the market. One source is a window defogger repair kit product thats sold at auto stores that has a conductive glue in it. Post open repairs will need to be checked with an ohm meter to make sure repair is good and that any adjacent trace lines have not been shorted by repair. Of those of you that have just bought or had installed Whirlpools defective control panel, please encapsulate the FPC cable as soon as possible to protect it from moisture. If you dont, it will surely oxidize again over time.

Just purchased/used the washer. One needs water to wash clothes. I added water to the machine just to get the clothes washed. How can this pass any reviews when it does not use enough water to clean a set of sheets? Not to mention rinsing. Does anyone wash clothes in the group that designed this machine?

We bought a pair of Maytag Bravo MCT washer and dryer on May 30, 2011. On April 30th our dryer would not turn on. We called the Maytag service where we bought our machine, and were told it was a fried motherboard and would cost approx $600 parts plus labour. For a machine to last less than three years is very unreasonable. Maytag used to have such a good name. That is why we originally went for this brand. We were told by the service tech, that if we opted to buy a new replacement machine they would waive the service call charge. Is this how Maytag keeps selling units?? We bought the higher end units thinking that they would last 10+ years but now it seems Maytag has designed their machines that are disposable. Tisk tisk Maytag. No wonder your service men are lonely... Your sales staff are too busy reselling to loyal customers. Well, you have lost customer with us. We are going to Sears to buy a new dryer made by GE and will sell our Maytag washer on Craigslist and replace it with the matching washer from GE.

I bought a Maytag refrigerator from Lowes. It has the freezer on bottom and I cannot put no fruits or vegetables in my refrigerator - it freezes them solid. Will never purchase this style of refrigerator again. Very Unsatisfied with this product

We bought top load washer model # MVWC425BW1 at Lowes brand new 9/22/14 for $493.93. On 11/23/2017 it stopped working and would not even come on after lid locked. Found out it needed new parts that would cost us over $300 to fix and we could buy another new washer for $400. We are very disappointed that this washer with only two people only worked three years when we thought we had bought a reliable product that would last. Sent several messages in November but no response till today 12/13/17 after filing. BBB complaint filed and they decline to do anything. So this company just wants to sell products but has no customer service. They only give a year warranty. Of course if the product is not going to last they want you to buy more.

April 26, 2011, I purchased a Maytag top and bottom fridge from Home Depot. After a few days, I noticed frost starting to form in my frost-free freezer and the fridge wasnt really that cold. I adjusted the dials thinking that may do the trick. Nothing changed, it was all the same and instead, frost was thicker. I contacted Maytag, which by the way was taken over by Whirlpool. I told them my situation and since I had just bought the fridge, I wanted a new replacement. They told me things didnt work that way, that I had to honor the warranty. Fine, we are almost entering October now. I have had several services calls, I have written to the Better Business Bureau, I have lost a few hundred dollars worth of food for it would be full of ice and had to be thrown out, I have contacted the executive offices of Whirlpool but they, along with the Better Business Bureau are not doing a thing. Tomorrow, once again, I am having a service call and once again, I know the issue will not be fixed. All I wanted was to either get my money back, along with extra for the loss of food or for them to just exchange it for another one, since this one was purchased with a problem. I really dont think that its right that they are able to get away with this. Just looking at this page, I see that there are plenty of people with this same issue. What is being done about it? If it were them with this issue instead of us, you know ** well they would have had a new fridge the following day. Here is my model# M1TXEMMWQ and serial# VS04658359 for this fridge. Please, I would really appreciate some help here.

Two months after my warranty expired, the motor burned out on my dishwasher. I called Maytag to see what they would offer, but they would only offer a discount on the actual part. I was so angry I was ready to buy a new dishwasher and forget about them...but I dont have that kind of cash to throw away. After going 5 weeks without a dishwasher (first-world problem) I paid for the part and a repairman to come and fix the dishwasher. Now 3 months later, the touch panel wont work. I am so upset that I wasted the money to fix this piece of junk. I will never purchase another Maytag again.

My husband and I just purchased on 4/8/17 a BRAND NEW MAYTAG 4.3 CUBIC FEET CAPACITY FRONT LOADING WASHER WITH STEAM AFTER OUR PREVIOUS 15 year old washer that we both used just finally started having issues. So we decided to go new and with front loader with good brand. How sadly I was wrong! We brought our washer home, hooked it up and turned it on with 1/2 load of tiny laundry. It didnt even make it through one load! This POS started throwing error codes E1, E2, F8, F9, Suds and wouldnt drain any water. We reviewed the manual again, checked the filter hoses and detergent. All was fine but washer wouldnt work! I called Maytag 2 days later on Monday and after repairman came to look at it Thursday said it needs new drain pump and today now power wont turn on and nothing will work on front of machine, mind you this machine is brand new! I am so disgusted and angry that any company would sell this quality to anybody and at the prices they charge! NEVER AGAIN WILL I PURCHASE ANOTHER MAYTAG!

I bought a Maytag Dishwasher Model #MDB7749SBW2 in 2013. It worked great for 2 years. In 2015, the control panel malfunctioned. All the lights on the control panel would light up and the dishwasher wouldnt start. I called Maytag. They sent out a service tech. He replaced the control panel. I started having the same problems two years later, 2017. I called Maytag today, 9/11/17, to see if they had recalled this dishwasher. No, it hasnt been recalled. They offered to sell me a extended warranty for $400+, that would pay for the service call and parts or, I could find another Maytag, Whirlpool or KitchenAid dishwasher and depending on the model, I could get a 25-45% discount on a new one. I asked why they havent recalled this model, due to the problems that so many people are having. They dont know. Im writing this review to let those of you who have bought this dishwasher know, that the product is faulty.

I bought a Maytag washer expecting To get the best and have already had Service on it three times and it still isn’t working. I have spent a fortune at the Laundromat when I have a 4 month old washing machine at home and not getting anywhere with getting anything back on this. I am very disappointed in this Washing Machine.

I am happy with this dishwasher. I had a GE that had a lot of problems. I insisted on getting Maytag and I have been happy ever since. It controls the time, temperature, and is easy to operate. I would like a bigger dishwasher because of my family size. This dish is okay for a family of 4. It matches my furniture. It blends in. No complaints. The digital pad is convenient but it has been fixed a few times. I had a few technicians who did not know how to fix. It was not the dishwasher, it was the technicians.

Maytag Appliances - biggest rip off ever! Home Depot needs to stop carrying Maytag appliances. I purchased a Maytag washer Type 832-A, Model number MHWE200XW00, Serial number HL11990545 in May, 2011 from Home Depot. After just three years it flooded my laundry room. Home Depot couldnt help me, and Maytag Customer Service tried to really rip me off.I called Home Depot, asked why they continued to carry a product they knew had terrible complaints and all they could tell me was they are sorry I am unhappy with my washer, then gave me Maytags customer service number. I called Maytag - first the guy tried to sell me a $400 extended warranty package - total rip off. Maytag should be ashamed, then said he couldnt help because it was past the time period. There is no telling how many people they are ripping off with that little deal. Consumer Affairs should be all over this. So then he offered to get a Maytag repairman to come to my house, but couldnt tell me how much the diagnostic visit would cost or anything else. He was worthless.I hired a local repair person to come to my home, the part is $140, its the tub seal, weak and flimsy - has a giant hole. I only wash clothes and towels, nothing else. My local guy is cutting me a deal on the labor, still going to be $200. Maytag isnt what they used to be and I will never, ever purchase another product from them again, ever. And I would suggest you dont either. Maytag appliances only last a couple years at the most, and its customer service is horrid.

OK, LAWYERS -- Where are you?!! You have a lot of very unhappy people who feel they have been justifiably TAKEN! Whirlpool needs to replace these refrigerators with another brand! We bought same bottom freezer Maytag refrigerator in 2010. Luckily, which we dont usually do, we purchased a five year warranty plan. Within six months we noticed the rubber seal on our refrigerator on the french door part was turning yellow and then getting darker. We feared something was burning the rubber. A Maytag repairman looked at it, called Whirlpool, told them that there werent enough parts to fix this refrigerator. Whirlpool asked him what they should do and he told him it should be taken out on the front lawn and burned (yeah for that repairman)!! Whirlpool agreed to replace the refrigerator with one, very similar but a new model #. Thank heavens, after our insistence, the warranty was extended to the new one. Now after about three years, we are having the same problems that all of you are having with the next one.. Our Home Owners insurance adjuster just gave us a settlement to have all the ceramic tiles removed, which are cracked in almost two dozen places, and whole floor replaced (minus our $1,000 deductible). The floor was put in new three years ago. The refrigerator repairman is next to come out. From what I have just read about all the complaints on this refrigerator, NOTHING is going to fix this problem short of replacing it at our expense. My advise to everyone --- FIGHT THIS. Write to Whirlpool (not Maytag -- Whirlpool owns it), and blast them over and over with letters and complaints and threats of lawsuits. Why should we be taken for that amount of money while Whirlpool does nothing but keep it. A class action suit is badly needed. Big corporations should not be able to take people over like this and get away with it. If it takes a lawyer willing to take on a class action suit, this is it! In the meantime, bombard Whirlpool with letters and dont stop! It takes persistence, but in the end -- most of the time, we will prevail. Big companies hope we will give up and go away. They count on it. Dont let them win!!! I have had a Maytag washer and dryer for twenty years with no problems. Problem is that Maytag doesnt exist anymore -- who is making this....?

I bought the machine at Lowes. It was cheaper than the regular old agitator washers which should have been a clue. I like the old agitator washers that fill as you put in the clothes. Lowes installed it, turned it on and did not seem to care that although water should have been entering washer, none did. They rushed out. Ok, my water to the washer was bad so it was a simple plumbing fix. Less than 1 year the machine was full of water and would not agitate, spin, drain or anything. It sat full of water. My brother looked at it, fixed the hose that was no longer attached and it worked! Yeah for 1 year almost when again the belt came off, fixed again. Trying to find correct belt is starting to annoy me. I want to take it and dump it. It looks pretty but is nothing but a piece of crap. Maytag, shame on you!!!!

Im furious beyond belief with Maytag. Im furious at myself for being stupid enough to purchase all new Maytag appliances when I purchased this home as I had horrible experiences with them in my former home. This concerns the Maytag over the range microwave oven model MMV4205AA. First of all, within 6 or 7 months after purchasing it while cooking a frozen dinner, the turntable just cracked in half. Maytag wanted $89 to replace it. I knew when the turntable cracked that there were more issues to come. That is not normal in any way for that to occur in a microwave.Problems continued, of course, and with each call to Maytag, they would say the same thing the microwave is out of warranty and refused to assist me. Its not some little table top thing that one can just toss out and buy a new one. I paid about $400 for it from Home Depot. Last week, without it even being turned on, it just stopped working. I checked the electrical supply and conduit to make sure that was okay. I called numerous service organizations who told me this sudden breakdown when the microwave isnt even turned on is a known issue with this model and several other Maytag over the range models. Ive called them (Maytag) three times in the last week and they refuse to provide any allowance and hear the same old thing, the microwave is out of warranty. I was willing to have them even just provide some assistance rather than replace the microwave. Ive been told by numerous service organizations that this is a known issue and that even if they repair it, it will occur again and again and Im best off purchasing a different brand, which I cannot afford. They gave me phone numbers for service organizations authorized to service Maytag products and this just goes to show how out of touch they are. They gave me one that isnt even in business anymore. How professional, not!Warning: Purchase Maytag at your own risk. I give you fair warning. Every single Maytag product Ive ever owned has been a problem. I will never, ever, ever purchase another Maytag product again. I would think just out of decent customer relations, that theyd repair this issue. To be honest, I dont really trust a repair as Ive been told it will happen again and again. There was no notice that the microwave was breaking down either. It wasnt turned on. One day, I went to use it and it just wouldnt work. Actually, I went to use the timer on it and thats how I found out it was dust. My advice is stay away from Maytag. If you read reports, there are more complaints on Maytag than any other appliance manufacturer in existence. Not only on their products, but their customer service too.

We owned Whirlpool front load prior to the Maytag set we now own. Our Whirlpool was the better one. Shorter wash cycle, better cleaning & never had a problem with the seal. Maytag dryer doesnt signal properly when laundry is dry. You have to go multiple times. I wont purchase another Maytag set. We owned a Maytag top loader set and they worked like they should have.

This dishwasher is reliable and has NEVER had any repairs. It cleans fairly well, but I do wash off dishes before I put them in. The one complaint I have is sometimes the dishes smell funny after washing. I think it may be our water though. I also like that there is room for oversize dishes and glasses on some of the racks. Overall, I would buy it again.

We have had the oven, a Maytag Gemini Double Oven model mgt8775xs02, for 3 weeks now and I am so upset. First off, I became violently sick from the oven when we first used it. I had a horrible headache and then nauseousness and then the worst stomach problems I have ever had. The toxic smells coming from the oven were too much for me. We had every window open. I looked online and found other people who reacted the same way to their new oven smell. But now we are on the 4th time using the oven. We did a self-clean and I thought that would help but no, it smells like someone is pouring gasoline into my home. I smelled it in pockets throughout my house. I have had the gas company out twice and a repairman. They all cannot figure out the problem. I looked online to see if other people were having a gas problem from this model and I am not finding it. It is horrible. I feel like I am being poisoned. I have not had a working oven in 2 and half years and I was so excited to get this oven and now my new oven is making me so sick. I am not sure what to do from here.

We bought the Maytag 2000 series washer and dryer stackable set in 2012 from Home Depot. My husband was smart enough to buy an extended warranty and year after year we renewed it. Guess what?? Year after year the dang washer broke. This machine was a nightmare! Now that the drum spider is broken they will not honor our warranty but want to give us $300 and guess what? I cant find a replacement for my good working dryer. We bought this set because we live in tiny space and needed them stacked. Maytag really put us in a corner and we have no money to replace both appliances. Horrible customer service. Horrible machines. Just a horrible situation. We dont know what to do.

My husband and I bought a Maytag Bravos HE washing machine 3 years ago at Home Depot. It is by far the WORST appliance purchase we have ever made in 40 years! This machine started making horrible grinding noises about 6 months. It is not rinsing properly and its leaving detergent stains on our clothing. This washer needs to be recalled. I will NEVER buy another Maytag product, EVER!

Purchased Maytag MDBH979AWW serial #FY4202009 from Lowes October 30, 2009. Control panel went out after warranty, and we replaced it. It quit working again in May 2012, and we replace the control panel, and then in November 2013 it quit and we replaced the control panel along with a new door latch just to be sure on December 4, 2013. The dishwasher quit working mid-cycle a couple of weeks ago only 9.5 months since we replaced the last control panel. Im fairly certain it is the control panel again. We have paid more to replace control panels for this dishwasher than we paid for the original appliance. There should be a recall and compensation on this issue. Very disappointed that Maytag and Whirlpool do not resolve this issue. We will be buying a different dishwasher, and it will not be Maytag or Whirlpool.