Shortly after purchasing my Maytag refrigerator had to pay for a new motor in the ice maker. The cover for the lower large food tray broke. Now approx. 4 years later am getting ice build-up on the bottom of the lower freezer unit, about one-half inch thick. It is enough so the freezer door wont seal when it closes and the inside builds up with frost. Not happy with Maytag or this refrigerator.

Nobody seems to know how to replace this part online. I have discovered what a POS this Maytag MGDC700VWO dryer is. The ONLY way to access this part is to beat an access hole in the bottom-left panel. After the repair, you are left with a nice 4 hole??? What an absolute POS! The back panel has screws but after removing them, I discovered the panel is also tack-welded! This is beyond stupid! Maytag used to be a great product before they were obviously sold to the Yugo factory. Time to move on.

Maytag MHWE450 washer - Purchased this front load washer/Dryer and pedestals 12-1-2011. The bearings are so loud when it spins that you cant hear anything. You have to replace the whole tub to fix it with no directions anywhere on how to do it. I had a Maytag top load washer for 15 years before this. They worked perfectly when I sold them. I thought these would be a great purchase for a lot longer than 2 years.

Washing Machine MVWC6ESWW - The fourth time was October 12; I called. Shreka at Maytag said she would send someone out at no cost on October 15, between 12-5 pm. Justin called from AE at 5:05 pm stating he was on his way. He then asked for my receipts. We were moving and had packed many things. He said he would call and find out. He said they were out 7/2011, 9/2011 and again 9/2011 all for the same problem. I requested in September 2011 that this was a lemon and send me another. I was assured if the same problem occurs, it would be covered. Well Justin said it isnt covered anymore and it was due to being made overseas. The cost to fix it is around $350 to $400. The washer cost me $383.40, plus I bought the matching dryer of $403.39. This makes zero since. Please advise.

We purchased a Maytag Bravo in 2011. With only three adults in the house using it for regular clothes washing, we were surprised when we had to call a repairman and the charge was going to be over $500 to fix the transmission and clutch. We had the same problem as described in many of the other comments, i.e., door sensor would not work properly and machine would not spin. Not even worth it to fix. Word is that Maytag is made by Whirlpool and if this is true, it would explain the disappointment. We have replaced more Whirlpool appliances than I can count. Never again Maytag!

This has the aqua cleaning technology, sounds real good. DOES NOT WORK! The cleaning is done by you as you nearly climb into the oven with a plastic scraper which they supply to scrape prior to the cleaning cycle. Then after you have used the distilled water in the bottom of the oven during the cleaning cycle (steam), you climb back in to wipe out the water and use something similar to a magic eraser to SCRUB the oven.Here is the real kicker....during the cleaning process, in between the glass (in the door) you develop water spots that cannot be cleaned unless you pay to have a service technician come out and tear it a part to clean it. According to Maytag THIS IS NORMAL and is proven (by their engineers without any documentation for the customers to be able to see) to be normal?? The consequence is a brand new stove will never be clean and it is the first thing you see when you come into my house. I AM EXTREMELY DISAPPOINTED!!!!

I have only had this Maytag dishwasher for 2 years. My control panel has gone crazy! The child lock is blinking and I never touched it. I have tried to clear it by touching the heated dry button for 3 seconds, every once in a while it will clear. It eventually will start blinking again on child lock. I did research and have found out that Im not the only one that is having this problem. I now have to get it fixed.

I paid a lot of money for this washer. It was recommended by a service guy from Sears. It is only 3 years old. I dont think it cleans well at all. Energy efficiency? Not seen on this machine at all. It takes at least an hour for a cycle. It is super loud on the spin cycle. Now it is leaking and has that stagnant odor that front loaders get. Really! Waste of money. Will never buy a Maytag again.

I purchased this washer in January 2017 at our local Home Depot here in Mexico. It was a washer/dryer combo. Now, in July, a mere 6 months and only a few wash loads later, it has gone from the worst machine I have ever owned to what I consider to be garbage material. First of all, it boasts about not using much water. This is true... Only 1/4 of your load is in the 3 inches of water at the bottom of the machine and the top 3/4 never even gets wet. I couldnt believe it. Now, I put 2 sheets in this morning and it fills almost to the point of spilling out, though I have to give it credit for shutting off the water before it actually did so. This is a NEW washing machine!!! I, along with a lot of other folks from what I am now discovering, are all in the same boat. I remember Maytag being a mark of excellence way back in the day... This is no longer the case. Stay away from this company... I know I will.

We purchased this dryer a Maytag Model MEDC200XW3 about 10 months ago. The dryer slowly over time began to take longer to dry our clothes. After watching it work and seeing that the airflow in the tube was not flowing well, I noticed the lint trap was not functioning well enough and over 50% of the lint was escaping the lint trap and plugging up the exhaust vent. I asked Maytag for a service to repair my dryer and explained my findings. The service person on the phone wanted to send me a lint brush. I told her to send a repairman. The repairman said that all lint traps let lint by and said it was my problem. Well today theyre closed and I cant even leave a message. Now I know why the Maytag repairman is the loneliest man in town...

We paid for a brand new washer and dryer from Maytag/Whirlpool. Right on the machines it has stamped in a metal plate 10 year warranty. So at 4 years when my washer started screeching and smoking I called for service. Yes, there had been a leak that burned out something in the engine and the bearings were shot etc etc. But they have been back 3 times. Each time they lack some part. I first called them on July 29, 2020. Today is October 13, 2020. They have still not got the washer repaired. I need to do wash every day. We are a family. We also have a senior in her 80s. And dogs. I need to do wash every day. So for weeks I went to the laundromat. That cost a fortune. Then a couple of weeks ago I impulse bought a new washing machine. A Samsung. On sale. Doesnt match the Maytag dryer. And the old washing machine got moved out to the garage. Its the pandemic. I cant keep going to the laundromat. What good is a warranty if Maytag/Whirlpool always has excuses for why they dont have parts. Its the motor. The very basis of the machine. It took them 2 weeks just to look for one. You wouldnt believe the excuses they make when we talk. But I am really unhappy with the way it all worked out. What good is a repaired machine 3 months later than I needed it. I had to buy a new machine. Why didnt they just tell me to do that on day 1 so I could avoid the laundromat. Why are they spending so much money to basically repair everything in that washer when they could have just bought me the new machine. When is a warranty not a warranty at all, but just a big lie?

I purchased my Maytag Neptune washer and dryer 5 years ago. About 2 months ago, my washer started making a lot of noise in the final spin cycle. Well, after I called my repair man (who I purchased the set from), they said that a back bearing is faulty. They suggested calling Maytag because the cost of the repair is $500. I called Maytag and was told that due to the age of my washer, there was nothing they could or would do for me. This is very poor customer service and very poor quality as far as I am concerned. I can hardly afford to get it fixed, but I also cannot be without a washer. Im sorry I have several other appliances that are Maytag in my home.

The soap dispenser along with the port it slides in becomes molded and is not easy to clean, front loader. I never had a front loader washer with this moldy problem. I have been cleaning it at least once a month,

I really love my front loader and it has no agitator to rip pockets and tear off buttons. The tub is very large and I can wash king quilts. I do miss being able to fill the tub and put in additives and then add the clothes to soak.

We have owned this range for a little over a year. Oven will not hold correct heat. Have temperature sensor replaced under warranty. Did not make any difference. You can adjust temperature up or down according to actual temperature readings, but the temperature swings so much that it is worthless to try. Very hard to get food baked right.

Like many others, my Maytag Bravo motherboard has stopped working after about 2 years. The clothes do not get particularly clean, it is extremely noisy, and the wash cycles are excessively long. I would not recommend this appliance to anyone.

Updated on 10/09/2019: Well I wrote a review on my brand new Maytag washer that we bought at Lowes in June. When I wrote the last review I was waiting for our repair. They did come to repair and I was told by the repair guy (keep in mind the washer was only 2 months old at the time) that there were 3 fail codes. He said that it was overloaded or loaded wrong.That you cant wash towels with sheets, you cant wash any kind of rug no matter the size, which I only wash small bathroom rugs that are NOT oversized or heavy, you cant wash tennis shoes (which I have not). So I asked him what is the point of investing in what is supposed to be a top of the line, heavy duty, extra large tub, commercial washer? He said that you cant do that with any machine. I told him our old washer that we had 13 years had no problem with washing towels & sheets together. My point is that I am 100% disappointed in this washer & I encourage you to NOT buy Maytag, apparently they no longer live up to their brand.Original Review: We did our research & comparing & this machine came up on top. Its size suites our needs & we were excited about all the great features. We purchased it in mid July of 2019 so its 2 months old & for the last month it started to shut off in the middle of a wash cycle. At first we thought that maybe we were doing something wrong. So we would re-start it & it worked. Fast forward 3 weeks, it was doing it almost every time. Now it isnt working at all, it starts to fill up then shuts down before it starts to wash.Today is a Friday & I called Maytag to request a service call under the warranty (60 days old) Maytag had me on hold for 19 minutes before I could even talk to someone! The customer service person (once she was on) was very nice & sympathetic but couldnt get anyone out to service our machine until Tuesday, which is a HUGE inconvenience since we have not been able to wash for the last 3 days. I am highly disappointed in the machine for the simple reason that I paid for a new topnotch machine because my old one that 13 years old finally gave out & now am in the same situation & in for $1000 I paid for this new washer & having to go pay to do laundry 2 MONTHS later! I will add to my review once they have performed the service call to see if the issue is resolved or the machine replaced if they cant fix it.

I could care less if Maytag responds as I have already advised all my family and friends to avoid Maytag products. After spending over $1200 to buy this refrigerator it took 6 months for the ice maker to failed, and it needed a control board replaced. Maytag had a great reputation; however, in the past 5 years their products are worthless. I also have a Maytag dishwasher which failed and was stuck on cancel with a flashing light. The dishwasher panel needs to be replaced and I have just decided to replace both of these products with a different brand.

The washer worked great for the first 6 months, then it didnt dissolve the soap, it wouldnt complete the cycle, and there is a loose bolt like sound when you spin the drum. The load level is not an issue. We have had the serviceman out four times, he has called the tech support each time and they cannot resolve the issue. Maytag said sorry! Unless it does it constantly then they cant help. The control panel has been replaced and the drum has been replaced. So we keep paying the water and sewer bill to rerun the load 1/2/3 times to get it to complete the cycle. This washer was purchased last May, 2011 and they say were stuck with it.

My complaint is not against Home Depot but Maytag Products. They are inferior products. Stay away from Maytag! Note: We are in our mid-to late 60s, no kids using these products and they do not get a lot of wear and tear. Maytag Microwave: MMV 4205DS-0, May 29, 2014 we purchased Maytag appliances for our kitchen (stove and microwave from Home Depot). I liked the 10 year metal warranty plate attached to the front limited warranty of the microwave. This means nothing! They cover the stainless cavity of the microwave (a part that will never go bad). June 3, 2014 this microwave was delivered. Thanksgiving, the microwave went out November 30, 2015 this was replaced with GE Profile Model JVM3160RFSS for $178. November 30, 2015, Diamond Factory Service was here for the Microwave. We paid $90 for the service call. They wanted $228.09 to repair (1-8206419 Switch $15.22; 1 W10269460 Switch $27.03; 1 W10727360 Microswitch $27.03 and Labor $155.00). Maytag Dishwasher MDB7749AWM. Purchased from Al race Appliance for $599.95 total with tag etc was $920.27 on 5/16/12. So thankful was purchased the additional warranty for five years. We have had 2 service calls so far for the same issue, which is W10356494 Console CMFF0312434. This is a known problem (it will not start). I wish I would have googled the model before purchase was made. When the warranty expires, this will go to the curb too.Also, purchased Maytag Neptune Washer and Dryer from Best Maytag, Rockford. The dryer had problems with the circuit board after a short time. Too expensive to replace. Our family and friends ALWAYS purchased Maytag only. No more! Stay away! We are waiting for the oven to go next. Oh and check out the bottom drawer. There use to be room for pots and pans. No more. Lucky to get your pot holders in there.

Model MDB4949SDZ0. 7/10/2018 Purchased from Costco. 7/23/2018 Installed by company arranged by Costco. 6/18/2019 A burning smell was coming from front control panel area of dishwasher when it was turned on. 6/25/2019 & 7/3/2019 Repair technician came to fix but could not find anything wrong so burning smell continued whenever dishwasher was one hour into cycle. 7/12/2019 Repair tech changed out front control panel because burning smell was still coming from handle area. 8/9/2019 Dishwasher does not drain completely when wash cycle is complete. Sometimes there is sudsy water left, sometimes it is clear. The water level is above the heating element at bottom of dishwasher.We only run the machine 2-3 times a week and have been using different cycles to see if the draining issue is with one cycle or all of them. No matter which cycle is used, water remains at the bottom of the dishwasher above the heating element. This seems like way too much residual water. Repair technician is scheduled to come for the 4th time to look at dishwasher but we just received a message that we will have to pay $129 service fee because dishwasher is now out of warranty. Maytag, fool me once, shame on you. Fool me twice, shame on me. Therefore, know that we will not be purchasing a Maytag product ever again.

The machine had automatic fill which did not allow enough water to rinse the clothes properly. I had to run another cycle to rinse the clothes. The machine was also extremely loud. When I had a warranty repairman come out concerning these two item as it was brand new, I was told I should have researched better. I gave it away after 3 months.

I bought a Maytag washer and dryer so many years ago that I have forgotten when it was. They have performed admirably under trying conditions. Our washer finally needs replacing due to the buildup of scale from our very hard well water. This after about 30 years of good service. Looking to replace them and will probably buy another Maytag set when they go on sale.

Ran washer with extra rinse and clothes came out with dry spots. The only way to get clean wash is to wash everything on bulky/sheets. We lost every appliance in Sandy. If I had known the machine was so-called water saver I never would have purchased it. I was in a hurry. I hate the machine.

Maytag Bravos XL HE MVWB725BW. Washer was fantastic at first. Then about at 14 months old, the spin cycle starting making loud noises. Called Maytag, they promptly dispatched a repair service. The estimate to fix the washer was $531. The repair man stated Maytag does NOT seal the bearings from the factory. They only rely on a rubber washer, poor design. Maytag was unwilling to help with a washer with their name on it that failed at 14 months in any shape or fashion. She mentioned that Maytag has a 2-10 warranty on the motor only (which is non-existent, its electromagnetic). This will be the last Maytag that I ever intend to purchase.

I bought a top of the line Maytag commercial washer. We had a number of service calls replacing parts, gear box etc. Then, they finally replaced the machine and all the same issues happened again. They will not take back their machine or refund me my almost $1K paid. The washer squeals when it starts washing and clunks all while agitating - I can hear it upstairs. After yet another service call (#11 now and no salary replacement for me) the result is that Maytag says when the temp in the house is 67 or lower, the parts in their machine expand and contract and will make noise. No fix, no refund oh, and no one you can contact by email in Canada to help. Moral of the story, dont buy Maytag.

The top loader washer Commercial Technology washes very small loads well. I bought it for the deepwater wash. It DOES NOT work. It also has a auto sensing. Hate this washer. I have to pour buckets of water in the wash to fill it. Maytag/Whirlpool go back to the way it should be. If I want a full washer I should have it! At the end of the day IT IS MY WATER BILL!

Before putting clothes in dryer you have to untangle them. Sweaters and even t-shirts become stretched beyond help. Clothes smell like mildew if you leave them in the washer even just a couple of hours. Im 50 and had a few washer/dryers and these take the cake. Ive used the washing machine cleaner/refresher (something I have never done on washers in the past) and still a mildew smell. The dryer has lint on both sides of the lint screen. And as stated before if you dont untangle your clothes they come out in a big knot, partially un-dried & very wrinkled. The lint on both sides of the screen concern me - Ive never had a dryer do that before. Its not much lint on one side but enough to think something is not right.

Maytag MCT Washer & Dryer - I bought the largest capacity to save time. However even my 6ft tall husband has problems reaching the bottom to remove clothes. Even worse is the lack of water to clean clothes, washes so long it wears clothes and they are still dirty. I tried to improve on my old Neptune and Id love to have it back. I may have to junk this washer. The dryer is very slow. Buying this set was tossing my hard earned money in the trash.

I bought a new Maytag refrigerator 5 years ago and it has been nothing but a headache. Ive spent more than $700 getting it repaired. The Maytag repairman is no longer lonely, hes really busy. These units are crap and the company does not stand behind their products.

This is the worse washer... As many other have complained I have the same problems. This washer it will not fill with water ever. It doesn’t rinse clothes or clean them as I’m use to the old washers doing. From day one I noticed the water does not fill in the tub and wondered how can the clothes be getting cleaned properly. Getting a F51 code and after going on YouTube and checking for problems it seems to say the same code after it works for a bit. This is the worse appliance I have ever purchased. I am so frustrated and will never purchase a Maytag anything again. Never did in the past up to this one and never will after this one.

I purchased an LG (white) washer last year, but my husband upgraded all appliances to stainless, including Maytag washer and dryer. The washer does not fill with enough water to cover the clothes. It barely agitates them to wash. Some clothes even come out with dry spots on them at times! They smell and are still dirty when done. I have tried every setting hoping that was the issue. Normal, power wash, none work any better! Had to resort to the soak function which does not add fabric softener or drain the water completely. Thankfully I didnt sell or get rid of the LG. Putting the LG back in asap. Nevermind the mixed color finishes of white and stainless between the washer and dryer. Clean clothes most important! Piece of garbage and complete rip off!

Its frustrating the way the bottom of the dishwasher has curves making wasted space. Second, the tracks for the trays are such that often the tray comes off the track and makes it difficult to get back on without unloading dirty dishes to do so. Finally, I really dont get the lighting system for dishwashing on the outside of the machine.

Most American dishwashers are made by Whirlpool. My control panel failed after only 3 years (design is terrible!). I had to pay almost 50% of original dishwasher cost to have it replaced by Factory Service Co. (formerly Whirlpool service).

I wish I would have read reviews before I purchased this washer, but I was in a hurry to get a new machine. Maytag has a great reputation and we went on that!! My Bravos is 2 months old and we have been away for a month! What a disappointment so far. What Ive noticed is all my dark items have residue on them, and today some of my light clothes came out looking like there is grease on them. Im afraid its going to wreck more clothes! Does anyone know if theres been recalls on the Bravos XL washing machines?

Bought the Maytag high efficiency washing machine with the auto-sensing and deep water wash feature. It took some getting use to because of all the washing choices and different noises it makes. Auto-sensing seems to use very little water which is strange but clothes seem to come out clean. Best bet for me is like the old school way and use deep water wash and light load which is shorter and thats most efficient power wise but will use more water which is fine by me. Also bought the matching dryer and thats a 5 star review. Excellent product.

We had a Neptune Maytag for over 12 years, best machine ever but this one (Bravos XL) is complete junk. We have been very disappointed in its ability to clean clothes with the length of time to complete its cycles is ridiculous. Its always out of balance with just a few pieces and lack of water twisting everything in knots. Well 16 months after purchase here we are with a broken machine, we have a fried circuit board. Maytag has lost our business permanently.

Im have finally given up and purchased a replacement for my Maytag Bravos XL Top Loading High Efficiency Washer! The Maytag was 2 years old and I have ALWAYS had trouble with it. My towels became sour after 1 or 2 uses (sometimes they smell sour even before use!). My dark clothes ALWAYS came out of the wash LOADED with lint. I researched online to determine whether these were common problems and found several sites with suggestions such as: dont use more than 1-2 spoons full of high efficiency detergent (which recommendation I followed), Use white vinegar or liquid fabric softener. (I tried both with only minimal results.) ALSO use a dryer sheet in the dryer (I did this but it seemed like a waste since I was already using fabric softener in the washer). Dont overload the washer. (I didnt, but if I couldnt fill it, then why did I buy a washer with such a large tub ?!) Clean the washer monthly. (I faithfully did so, and tried alternating Affresh and bleach to see if theres any difference in the result... not really. Make sure you are fully drying the towels (I ALWAYS DID!).We had a Sears repair technician come to the house the last time my frustration level was overflowing and she only made me feel like an idiot, repeating some of the above recommendations and insisting they would solve the problem -- which, if they had worked, would have precluded my need to call a repair technician!!! The repair technician provided no other service or ideas to fix the problems. My husband decided we should go back to the tried and true agitator-type washer... bye-bye, Maytag Bravos.

I purchased this Maytag washer/dryer set in February 2017 and I am very, very happy with it. This is a brand that has proven dependable for more than 80+ years. This is a low water washer that saves money on energy bills. I love the extra large capacity and was very concerned how well it would clean without an agitator. But having confidence in the name, which is why I purchased this set, I was very pleased with the cleaning power. The only disadvantage I see is with the soak cycle which is timed. I would like to have an option to soak indefinitely. So if you are trying to remove blood stains, you may have to use the soak cycle a few times before all the blood is removed. (Assuming that you are only using cold water and no additives.)

I purchased Maytag fridge a year ago and it has been a nightmare. The freezer doesnt freeze items. the drawers were all damaged upon receiving. I have contacted Maytag for more than 10 times and 5 techs came that I paid 125 each visit to fix the fridge because I didnt purchase the warranty thinking it was a good product . It is not! They dont stand behind their word. They lie and they send unqualified techs the misdiagnose issue to collect service calls. Please avoid this brand by all cost. My experience is terrible and I never want to wish it on anyone.

This Bravo Top Loading Washer does not thoroughly clean my clothes. It doesn’t fill properly with water, and it leaves soap residue on my clothes, because it’s not using enough water. I’m using the 2 rinse cycle trying to prevent this, and it’s still not enough. It has actually ruined a few of my items. It is the WORST washing machine I’ve ever purchased. I’m disappointed in Maytag for producing such an awful machine and Sears for selling such a sub par product.

we have trouble with maytag doublre oven. the oven is over 100 degree off set temp and is not consitant. some times high some times low. we have had ae repair out they relaced control board and circuit board same problem still exists. we had turner repair out they took a reading when it hit desires temp but did not stay to see temp rise above or below set temp. turner repair another tech order a temp probe the turner tech put in probe and jst left didnot even check oven. he was pissed off I quess. same problem still exisits. We bought stove from Nebraka furniture mart the said theyont support repair after 30 days. we hope and pray that the tech will report to Maytag (Whirlpool) that the stove is bad and we can get a new one. So far no repair action has helped. We had a repair person out to repair a leak on a whirlpool washer . he also is qualified on stove but not a whirlpool repair authorized repair person. He checkedd the stove and said it is 100 degees off and we need to get a new one. We need some help with this problem please help us or tell us who to contact to get this problem resolved. gary Luttrull 816-618-3277

Please read Michael of Davenports review. I read it and word for word this is my experience. This washer is the worst Ive ever had. If I could get back my old 20 year old machine, I would trade it in. Dont buy, youll hate it.

This is the most horrible washer ever. Within 3 months it would not go beyond sensing mode and never fill or wash. Tech came and fixed it... 3 times. It still happens and I have to jiggle it all around to activate it. Clothes are never clean, dog hair is never washed out... My broken old agitator machine was taken to the dump & I wish I had it back! How do the stores give this machine a good rating?? I cant do light quick washes, I have to wait forever... Our water bill is 2x higher than ever because if I dont fill the tub with deep water, the clothes dont even all get wet. Hate, hate, hate this thing.

Maytag has really gone downhill. Had trouble with a factory defect in a new French door Maytag refrigerator within a few months (had it returned) and now the Maytag Centennial EcoConserve Top Load Washer no longer spins after only just barely 2 years of use... I will NEVER buy Maytag again. That is a promise. I will put more money and buy more expensive products from your rivals if it means avoiding Maytag products. That is my advice to anyone reading this review. The washer was used for MAYBE 10 loads of laundry per month... Yes, just for two people who have desk jobs so It was never stressed out. Used HE laundry detergent. Quality is a thing of the past for this company. Your reputation is in the doghouse.

My fiancee and I purchased a Maytag washing machine from our local Sears. We got it home and it worked fine, but after the first month it wasnt switching over from cycle to cycle. We called Sears and they stated that they didnt provide service to the washing machines, so we would have to call Maytag. We called Maytag and they sent servicemen from B & B Appliance to our home. We were told that they needed to order a piece and would be back at another time to fix the washing machine. They came back and said it was fixed. I went to start a load of laundry the following morning and the basement flooded. The hose had become dislodged when they were working on it. To add insult to injury, the washing machine was still broken. I called Maytag to request a different service company come to our home. Maytag said that they couldnt send a different company. They also couldnt replace our still broken washing machine and they could not accept a return. At this point we are out an almost $800 for the washing machine, over $5000 (which we have submitted to insurance) for the damage to our home, and almost $600 for a WORKING washing machine that was a different brand. We will never use Maytag ever again.

I purchase the Maytag dishwasher Model: MDB7749SBM from Home Depot in Plano Tx around June of 2013. The start/resume and cancel/drain button lights either flash or wont turn off and keeps trying to restart the wash cycle. I have only had this DW for 1 1/2 years. That’s pathetic! I went through the manual and tried everything it recommended but it didnt work. So far the unit still cleans dishes. Based on all the reviews I have seen on these Maytag dishwashers with the same issue, you would think there would be a recall. All the appliances in my home are Maytags and Whirlpools. Maytag and Whirlpool are now the same company. Depending on how they handle this issue will determine which appliances I buy in the future.

Sounds wonderful. Thats what I thought when I let my son have my 20-year-old, still running older washer. I wanted a new one. It worked good for 3 years and then one night I went to throw the clothes in the dryer and its full of water. After the last rinse and spin, it filled again and stopped. So I tried it on every cycle and got the same results. I thought, No problem. We have a great, honest repairman. Ill call him the next day and hell fix it. When I called and told him what type of washer it was, he was surprised it was working at all. Seems they had a problem with water leaking into the transmission. Apparently, I was lucky that mine had worked for as long as it did. Like I said, Im lucky to have an honest repairman. He told me he could charge me to put in a new timer and solve that problem, but I shouldnt waste my money since it is just a matter of time before it goes bad. Seems they were all bad and Maytag never made good on them. Told me the smartest thing to do would just to go ahead, bite the bullet and get another. It will be here Tuesday morning. Hopefully, this will be the last one I have to buy (keeping my fingers crossed since I had hoped the Maytag was going to be the last). My old machine is still running great for my son. Over 30 years my repairman has had to fix quite a few things for me - ice makers, dishwashers and even a timer on my old washer. Thank goodness he was honest enough to not fix my washer. I dont know if there are even any Maytag products around now, but if there are, they will never get my business. I spent a fortune on a machine that should have lasted the rest of my life. Ive had childs toys that lasted longer. My advice is do not buy Maytag.

We love our Maytag ovens. It always cooks evenly and we never have HAD any issues over the past 2 years. We will always buy Maytag! It has a self cleaning option and I have never burned anything on the oven.

This refrigerator has been my worst nightmare come true. Everything existent freezes: salads, tomatoes, berries, cherries, milk, water, etc. Never again will I purchase a Maytag product. Service is non-existent.

I have had Maytags for 20 years and never have been disappointed before I bought the Centennial and it is junk. It doesnt even put enough water in to wash the clothes. After it breaks, I will never buy Maytag again. When did you guys start going down the drain literally? My clothes do not get cleaned. I live in the country and we all get dirty. We need a dependable washer and dont even get me started on the dryer. I thought maybe you would care enough to know.

We bought this stove because of the self cleaning oven feature. What a ripoff! The Aqualift technology simply does not do the job that it is supposed to do. As the lady of the house says, Self cleaning means clean it yourself. Whoever engineered this thing needs to go back to school. Adding insult to injury, we have adjusted the oven temperature to its highest and it still cooks so low that a cake has to be cooked for half as long again than the recipe calls for or the middle of it is still raw. We would like to sell the stove but would hate to burden someone else with this piece of junk.

Purchased a new Maytag washer and dryer in November 2015 after having a old set not Maytag for 25 years with no repairs. WOW. Then the new washer went out in Feb. 2016, now the dryer in May 2016. Very unhappy. Is it because the machines are now made in Mexico? Cheap labor and cheap parts. ICK!!! Thank god for the extended warranty.

Can not wash 4 pairs of pants or 2 sheets because they get out of balance when the spin cycle begins. I had to take the clothes out and move them around to keep the balance. Very unhappy. Would not recommend this washer.

Model #MFI2670XEM0, Maytag fridge top French doors, bottom freezer. Purchased fridge in May 2011 from Lowes, with a matching microwave. A couple months ago, I noticed puddle of water on wood floor in front of fridge, so I opened freezer to find ice on bottom with a sheet of fresh water on top. Call to Maytag was useless, also tried to sell us warranty. Guess that $300+ warranty would cover one year, so after the warranty runs out, would we have to buy another when it plugs again. Our kitchen floor is ruined, and the warping is coming close to our dining room. Googled problem online to see if there was an easy fix since it was out of warranty. I tried to defrost as described online, only to have it leaking again a couple weeks later. Will never buy a Maytag again. Guess that repairman in commercial is never busy because Maytag wont stand behind their products.

Turned the oven on, and it failed to light. A little while later, it started leaking gas into the house. Im lucky the house didnt explode!

Currently own model MTB1504ARW, serial number 12541413GT refrigerator. The defrost thermostat broke and it is causing the device to frost over and not cool. Maytag is trying to replace the part with part number 63001051 and that part does not match the part that came with the machine. I spoke with a supervisor, Mr. ** who certainly was not a problem solver or any help, in other words, lacks customer service. I explained the installation of the wrong part may be dangerous and could cause a potential fire or hazard. He assured me this was the part available, but also said it was discontinued and I would have to find it with an outside vendor. I explained I compared the part removed and the part they are suggestion, per the part list, and its the wrong part. As a supervisor, Mr. ** failed to provide true customer service for myself and future customers who may be in the same situation, with the potential of causing a hazard for customers. The Maytag supervisor should learn to provide customer service and prevent possible hazards for customers, taking the next necessary steps or research the issue with other departments within Maytag. The parts below are evidence of the issue, the suggested part has two wires, the one from the refrigerator has three... poor customer service, at best with potential hazards to families and children. It may because their appliances dont break, according to their commercials, they just have too much time on their hands and cant provide the assistance that is needed.

We purchased a Maytag MVWX655DW1 Bravos MCT washer in 2017 and I recall a sloshing sound during agitation. Its a high efficiency model and was okay for several months, I think. It began to make something of a clunking sound during agitation that was similar to the deceleration sounds when the spin cycle completes. It seems that is an indication that something is wrong. Clothes arent clean after washing - another reason to suspect a problem. I observed the wash cycles and noticed that some items dont even get wet during the wash cycle. The clunking is probably an indication of the type of failure but I couldnt find anything other than someone else asking the same question when I did an internet search. Expected performance is shown in a company video with water sloshing during agitation. Thats the key take-away. My basket moves back and forth an inch or two during agitation and makes a clunking sound at each direction change. Water isnt sloshing through clothing and some of the garage rags that were once my clothes probably just needed a good washing. I suppose that even cleaning the washer isnt accomplishing much. The spin cycle is actually impressive. I load the washer evenly and find the completed loads with a towel or shirt evenly covering the clothes pulled to the basket below. Unfortunately, thats probably the only part of the process cleaning anything.The enclosure says its designed and assembled in U.S.A. and, unfortunately, speaks to our manufacturing ability. Some of the engineers Ive worked with over the years suggested areas to inspect. I was able to use my phone camera to look under the unit and noted that it is controlled by a main drive motor and a little synchronous motor with a linkage that Im guessing changes agitation direction. Both are made in China. Ive considered repairing it and just pulled the wash plate for inspection and found nothing beyond the difficulty of pulling the wash plate. Probably an issue with the drive assembly and a few hundred dollars in parts to fix. Ive also had input from someone about the cost of replacing the control board. I grew up with TV commercials of the Maytag repairman with nothing to repair in the world of reliable, American products. Its disappointing to find that is no longer the case. The low tech GE washers weve used all our lives were old and ugly when they left our house. Not defective, a few drops of oil below or worn finish but still working. It really is a disappointment to look at where we are today. It didnt have to collect samples on Mars or deliver orders in a self-driving vehicle. A reliable washer to clean dirty clothes is all we hoped for.

I had a GE washer and dryer when I first moved to my new home - lasted 15 years. Then... bought a set of Maytag and they have both been the biggest pain in the world. Spent 3000 and Im ready to toss them after 3 years. Dont buy Maytag!!!

I have owned my Maytag Neptune Washer since 1998 and this is the first time that it will not drain all the water... Doing some research before I call a repairman... Have a Great day!

Washer does not clean very well, clothes are left with spots. The water level is never comparable to the clothes thats in the machine, it causes me to lose a lot of water as well as detergent. This machine is the worst washer we have owned. Its also very noisy.

I have been struggling with this machine for the last year. Just does not wash. I have tried power wash. Bulky sheets. Double rinse and nothing works. I bought this machine last year from Lowes and its my worst investment. When the load is finished the clothes are still dirty. Actually worst than when they went in. Read the entire booklet to no avail. Hate this machine

Nineteen months in a home of empty nesters and the darn thing is a game of trying to outwit its electronics. We live a long way from town, which makes service calls a high dollar thing. I have spent considerable time this weekend trying to cipher its moods and order parts. This washer was purchased on an invalid reputation. Others beware.

I purchased a Maytag dish washer (not even 2 years old yet). I bought it on 8/29/10 and I paid over $400.00 for it brand new. The model number is MDBH949AWW1 and the serial number is F03422327. I am only asking for the part (motherboard). I have lots of friends and associates at church, work and social that I have talked to about this Maytag. And I would like to give a good report about the company and what they make and that they stand behind their workmanship. I know for a fact that they have 22 motherboards on hand ready to go out and what I have read online is that many people are having the same problem. I need a motherboard. I believe this unit should easily last over 10 years, so I am not asking for much. I will have it installed myself. I just need the part. I trust that you are a reputable company that has been around for many years and Whirlpool has taken new ownership and they have been around for a long time, too! My own parents owned one for over 30 years. This is all that I would request. I’m thanking you in advance.

In May 2007, I bought a matching Maytag Neptune washer Model MAH5500 and dryer. I also bought the 3-year extended warranty. Approximately 4 years later, actually 1 month after the warranty had expired, the washer started to get very loud and sounded like a jet engine taking off. I called Brennen Repair Service in Midland, Michigan. The repair man came out and said he did not even have to look at the washer. He knew what was wrong. The bearings were going in the machine. He said I could fix it for approximately $600 or just run it till it quits. I was furious. I called Maytag and explained my issue and was told that there was not a recall and they could do nothing to help me. They even told me that they had not had any complaints of this nature regarding this model. I told them they were full of it. I know of at least 4 people in my family and workplace that have had to replace the Maytag front loader piece of ** washing machine. I think Maytag should stick behind their product with all the complaints out there. I would like to shove my washer through their front window. I previously owned a Maytag washer for 25 years and had not one issue. It ran perfectly. I will never buy another Maytag product nor will anyone in my family. Maytag, you suck. Your service and reputation is appalling.

My husband and I purchased a Maytag stainless steel French door/freezer bottom ice making fridge from Hhgregg in Brown Deer, WI and 8 months later (now), Ive been told that my food that is spoiled, cant be replaced and my service for the fridge wont be done until next week! I have 5 kids and a husband. This has turned our world upside down. I called them and spoke to a Nicole and she said they cant do anything for us, but we can try to contact the diamond repair service at 269-927-2519 to see if they can get us in sooner. I asked for a refund for the fridge and she said no, the 10 warranty only counts for repairs... I am so angry that I didnt research Maytag before now. I gave the Whirlpool fridge to the delivery guys of Hhgregg and I had that for 18 years and it never went out on me. If anyone is reading this and is upset as well, let us get together and start a class action suit!

I have the model with a smaller oven on top. I use it about 98% of the time so Im not wasting energy having to heat a larger oven space. I also like the fact that I can clean one oven. The larger oven is used when I cook turkeys. I can cook many dishes at a time, by using the smaller oven for dressing or cakes.

We purchased our Maytag gas range in 2015. Within 6 months we noticed the clear coat and paint was defective, we called Sears, they allowed us another range top and replaced it but told us our warranty was up in a month and they would not replace another. The stove always looks dirty because the clear coat and paint have bubbled up and it is clearly a 100% manufacturing defect that should be recalled.

We purchased a wall oven model MEW7530DE 11/8/2014 which was installed the first part of December 2014. From the beginning the temp was not constant and everything baked was either burned or under baked. The first repairman said the control panel was faulty and was replaced four months after purchase, the problem continued. After three more repairmen all from different companies concluded they could find no problem and thats just how ovens work now. We contacted the owner of Hamiltons Appliance, where the oven was purchased, and requested a replacement oven which was accomplished December 2015.New oven, same problem, very disappointing. My wife has been baking for over 50 years and has never experienced problems and frustration on this level. The condition of the oven is totally unacceptable and with all the effort by us and others we are at a loss. We purchased an extended warranty which has resulted not fixing of the problem. We hired an electrician to inspect the wiring in case that was the problem, costing us $200. The wiring was all good. What do we do next and what are our options short of another new oven. WHAT IS MAYTAGS RESPONSIBILITY? Respectfully, a very unhappy customer.

Worst washing machine!!! I purchased the top loader Maytag Bravos washer HE in 2011 and they are the worst!!! It has been repaired three times already and now is making such a loud noise and I have been told it is the bearings. I did purchase the extended warranty and it expired. The reason I did not get a renewal is Maytag & Home Depot do not allow the the extended warranty company to let you know the warranty is ending. So now I have a 3 1/2 year old washer that needs bearings and will cost $500 + for repairs. Will not be spending anymore money on this absolute piece of junk. I had a Maytag that was 22 years old that I replaced and thought I was buying the same quality but never again another Maytag. This company may want to employ only repairmen because you will need only them because no one should buy a new one going forward.

The bearings and motor went out in less than 3 years. The warranty good - the dealer I purchased from Siano Appliance gave me credit to purchase another Maytag washer - which I had to purchase an additional warranty for $320. The new Maytag is less than 5 months old - the motor has been replaced and waiting on a tech now to fix it. It would not come on. SO in warranties I have paid over $640 and am still having issues with the new washer. The first time I purchased a warranty for 10 year - when the machine was replaced I had to purchase another warranty for that machine - now if I have to replaced this one that will be an additional $320. IS this legal?

My 6 year old Maytag 3000 series front load w/d set started leaking after 2 years. Minor leak on certain wash settings such as Rapid Wash setting that worsened (and I could live with), so that setting wasnt used. Last month the washer door was flapping open DURING a spin cycle. I stopped machine only to find the entire barrel had dropped and metal wire wrapped around clothing. Worst washer ever!

In October of 2011, I purchased a $1,199 Maytag Bravos Washing Machine. It recently started making a really loud noise during the spin cycle (REALLY loud). I had a local appliance repair guy come and he told me the main tub bearings are bad, sealer is defective and that it would not be cost effective to fix it.I called Maytag and they offered to sell me another one for $839. I am very dissatisfied that I only got 4 years out of a $1,199 machine!!! Ridiculous!! I wouldnt mind a minor repair that cost a few hundred to fix... I get that. But for it to be junk in 4 years... I have a hard time with that for the price. My appliance guy said it was junk when I bought it. Year ago, you got 15 to 20 years out of a good washing machine. Now... I buy a high end machine and it lasts 4 years. And why would I spend another $839 for the same piece of junk!!! That would be throwing good money after bad. It is not going to happen. I promised Maytag that I would post as many reviews about their product as possible... so everyone can know that they make a lousy, defective product and charge a very high price for something that will not last. Dont buy it!!

Our Maytag dishwasher was just past the 1-year mark when the control panel stopped working. A certified Maytag repair service came out to diagnose just that and charged us $89. Maytag sent the user interface out to us, and my husband noted that there was absolutely no way that the part could be installed wrong. The wires could only go one way. The repair service (DSM Appliance Service) wanted another $120 to install it. We installed it, and it still doesnt work. Maytag will no longer assist us in any way. I will never buy a Maytag or Whirlpool appliance again. After investigating, I see that this control panel issue has happened many, many times; and I wonder why there hasnt been something done about it.

I had my dishwasher for several years. Never had an issue with it. Cleans well and is very quiet which is exactly what I needed. A quiet and effective dishwasher is hard to find. The price was about six hundred dollars. I pursuit at Lowe’s. It was on sale along with a military discount.

I have a Maytag Range that I bought new and installed 6-1/2 yrs ago for over $1200.00. I am single so I rarely use the ovens. The upper over I use maybe 1-2 times a month and the lower oven I may use once a month. The night of 3/7/2016, I used the cleaning cycle set on medium for both ovens. Yesterday, when I went to wipe the ovens down, I found the lower heating elements, on both ovens, had snapped. The top ovens lower bracket had broken in 2 places, the first break is about 2 from the connection, on the right side leaving about an 7 gap. The lower ovens element had broken in only one place about 2 from where it connects into the back of the oven. This has to be a flaw in the either the design or the material. In the 45 yrs that I have been using ovens and stoves, my last stove was over 35 yrs. old, I have never had a heating element break. While I can understand a break at the connection, I can see no reason that the it would break in the center of one side on both lower elements in the same oven. I also noticed that lower heating elements are a much small gauge than the top which I find strange.The other issue with the stove is the seals around the windows are not tight. I noticed dust was inside the two glass panes. The rubber seals were sunk down into the door, but Maytag said it was not their problem that I must have done something. When I remodeled my kitchen, I bought all Maytag products: 1.H20 Frig - The electronic panel went out after 3 months and had to be replaced. Manufacturing Defect - When the repairmen came to fix it, he told me to call Maytag which I did. They refused to pay for the repair because I called a repairman first, even though the business was Maytag certified. Even though I said I would cancel the service call they said because I had made the appt. and they recommended I call Maytag, they would not cover the repair. 2. Stainless Steel Dishwasher (Cost over $700.00) - Motor went out after 3 yrs. 3. Microwave/Convection Oven (above the stove)- Convection light out after 4 months. The replacements are not inexpensive.One other complaint I have is when I bought all my large kitchen appliance Maytag had a $600.00 rebate offer. Even though I mailed all the required documents to the company over 2 months before the rebate ended, I never received my rebate. The explanation I received was that the center that received my documents delayed forwarding them to the proper department that processed rebates and they were received after the offer ended. When I questioned the legality of the practice, I was told that this was all explained in the Terms and Conditions (ie: small print).

We finished a kitchen tear out and full remodeling. From top to bottom adding the Maytag double oven insert into our cabinets. We checked out reviews and MANY stated that the oven's fans were LOUD! But we've had them now for 4 months and the reviews do NOT give an accurate account in my opinion. My wife loves using the ovens for all sorts of cooking and baking projects and the units are NOT LOUD at all. You'd have thought from what we read about the ovens that we were making a bad purchase but that's not the case. Quiet, even cooking and a GREAT PURCHASE. If your ovens are loud when cooling something must be wrong! Or maybe we got LUCKY!? I don't think that's the case at all but then I haven't used other's ovens only ours and we are pleased!!! 5 STAR for sure.

We purchased a Maytag refrigerator (freezer on the bottom) in August 2012. In 2014 we had to have the freezer repaired (defrost drain) which cost $153. This month, July 2015, we had to have the refrigerator repaired for another $293. The problem with the refrigerator the repairman told us is the control board (p/n W10503278). He stated that they didnt make the first board very well and hes been replacing this part quite frequently for customers. I only spent $799 on the refrigerator and I already have $446 into it. That is half of what I paid for it! I wouldnt recommend Maytag to anybody!

I purchased my Maytag side by side refrigerator 11/2011 and by 3/2012 the compressor went out flooding my pool house floor. Maytag replaced the entire fridge because I was only a few months old. I bought the 2 year extended warranty, went down to the pool house (which has central heat and air) and the compressor has gone out again! The results leaving my baseboards molded! My warranty went out 3/17/2015 and Maytag is helping NONE! The only thing they have to say is you can buy a new repair one warranty for $363 to repair for one year. I have had this refrigerator for 3.5 years and now this is the second time its gone out! Customer service said, pool house is different than a regular kitchen. I told her that the pool house is 1,000 sq heated/cooled kitchen, bathroom, sitting room. Thats no different than some houses. Why would that make a difference?? My parents have a 30 year old fridge on the back porch thats still running! I will NEVER purchase another MAYTAG product! Stainless side by side with ice maker.

I will never buy anything made by Maytag again. I just bought this washer 9 months ago and the sensor broke. The repairman said I have to pay $300 for the new part and it will take 3 weeks, then the repair told me many people have this same issue and he wanted to be honest that this always happens to these washers and my best bet is to buy new... I am so sad I saved for 4 months to buy a new washer and it was a bad decision. I have learned my lesson.

Maytag MFD2561 - The metal piece between our French doors is also rusting. It is a design flaw. We also have a GE French door refrigerator and that piece on it is not metal!

I purchased a Maytag model no. MDBH979AWB dishwasher on 4/28/2010, and I did not take out the extended warranty. I thought a Maytag product was built to last, but according to Maytag, I am wrong because they only offer a 1-year warranty on their products. About 2 months ago the hi-temp button on the control panel stopped working. Then a few days ago, the START button stopped working, I emailed Maytag and they sent me a PDF file that shows the warranty is only 1 year. I purchased the dishwasher at Home Depot, I went there and talked to customer service, they were no help either.I am very disappointed in both Maytag and Home Depot for selling products that Are CRAP! I paid $499 for this dishwasher, and if I would have known it only came with a 1-year warranty I would not have purchased it. I will no longer purchase any products that are made by Maytag or any products associated with Maytag.

I purchased a Maytag top load HE Bravo 700 3 yrs ago. I only wash 3 loads of laundry a week and the bearings went bad in the washer! Maytag/Whirlpool will do nothing to help me because they say I should have purchased the extended warranty. Well there is NO WAY that I could have worn out those bearings; it was a manufacturing defect that caused them to fail and hundreds of people online all say they have the same issue. The repair cost is $400 and would only have a 90-day warranty so I might as well purchase a new washer. Home Depot (where I purchased the washer) has been very helpful and is offering me help on the purchase of a new washer, but even they could not get Maytag to do the right thing and repair my Bravo. I am going back to a none HE machine with an agitator. This has been a horrible experience and Maytag has no business putting commercials on TV that say they are dependable.

Purchased this Maytag microwave brand new on April 2017. In January 2019 began to have issues with the display reading open/close door. Maytag would send a repairman for $160 to take a look at the problem. Parts of course are extra. I will never buy a Maytag product again.

Bought the Maytag MDSH969AWS1 in Dec. 2010, and it quit after 4 and 1/2 years. Ironically, replaced a perfectly good 20 year old GE model that ran great for this piece of junk. I tried to diagnose the problem: the washer fills, but when the cycle is supposed to start it just hums. Then you have to drain it. So I think the problem is the motor or capacitor. The parts are stupidly overpriced, and Im not even sure if that is the problem. It could also be the electronics board (Ive heard of the problems with these on this brand). So instead of risking wasted time and parts Im junking this, er, piece of junk. The stainless steel door was rusting on the bottom too. American made crap! Bought a fancy Samsung to replace it, and will NEVER buy Maytag again. Im old enough to recall the lonely Maytag repairman -- Itd give him a swift kick in the rear for being associated with such a shoddy brand. Maytag, its the Dodge-Jeep of appliances.

It’s a nice look to your kitchen first, and an easy clean. Works great for heating up stuff in a hurry and makes popcorn perfect on the popcorn button. Does ok at melting things. I have been happy with mine for 3 yrs so far.

Clothes are never submerged in water. Clothes come out worse than when they went in. Every review and complaint mentioned is dead on! This Bravos XL is a piece of crap. Stay away from lying salesmen from HH Gregg. And stay away from Maytag. Perhaps we should all get together and file a class action lawsuit! And donate all monies, washing machines and dingy clothes to charity!

I have a 6-month-old top load Bravo Washer. It has destroyed two bottom fitted king size sheets and 2 shirts that now have holes. It apparently slices the sheets during agitation. I have a service policy and called the service agency. The technician said there was nothing wrong with the machine, yet it literally ate 2 more items. Help! I need a solution to this problem.

I purchased my Maytag MDB7749AWM2 dishwasher approximately 3 years ago. Since it was stainless inside and out I felt that I was making a long-lasting purchase. The handle on this particular model doesnt have a latch release button. You are actually just pulling the door open. That would be fine if they had used something besides plastic on the control panel cover where the handle is built into. The control panel is only held together with plastic pieces that the screws go into. After only a couple of years of pulling on this the plastic parts holding the screws have all broken causing my control panel to just flash. My husband is a maintenance engineer and upon taking the screws out couldnt believe with such a high quality machine that they had used plastic in the main place where they needed strength. The wiring was cut so short to the control panel that one of the plugs had come undone when the cover began separating. I only need the plastic cover because my control panel is working fine but of course you have to buy the entire control unit which is $150.I purchased Maytag because I thought they represented a reputable American company but I was very wrong. When I contacted Maytag about the problem they were very unconcerned and just gave me a link where I could purchase the part. When I told them it would be my last Maytag product they didnt even have a comment. Giving Made in America a bad name.

We purchased a Maytag Top Load 5.4 cu ft efficiency washing machine. May 2019. It was making a funny noise already mid October and we had 8 parts replaced. After that it completely stopped working. We have been without a working washing machine for 2 months now. The technician has been to our house 4 times. When he came on Dec 31st to replace the mother board, that didnt solve the problem. He says the washing machine can not be repaired. We have been fighting with Maytag Canada and Lowes since the beginning of December. Neither company cares. We will never own another Maytag product. The company are crooks.

This appears to be a common, known, well publicized problem - freezer drain clogs and needs to be either changed or repaired with a fix, a free replacement part for the drain seal. Easy to install, takes 15 minutes. HOWEVER Maytag will not give you the part!! In order to take advantage of Maytags correction for a well known, chronic, manufacturer defect, you must engage an authorized service person for hundreds of dollars and wasted vacation time waiting at home for them to show up. Unlike any other product, recall this one is not free. My kitchen is full of Maytag products; dishwasher (not so good), range and a refrigerator that had to be replace when the compressor went out after six years. However this is the last straw, Ive learned my lesson, seen the light, THIS IS THE LAST MAYTAG PRODUCT I WILL EVER BUY.

Ive had a Maytag washer and dryer for 10 years. They have worked well, havent had any problems. I bought Maytag because of their excellent reliability, which has proven true. Design is not as modern as others, and doesnt have all the features, but overall solid reliable washer.

There was a maytag dishwasher in the house we bought 11 yrs ago. The only problem we have had is a recall on the rinse aid dispenser which was replaced by a service man but never worked again. We are completely satisfied with the operation of the unit, our only disappointment is the wire racks. The original racks plastic coating broke at the end nubs and became rusty and swollen. We found someone selling a unit and we just took the racks and left the unit for him to resell rackless. Unfortunately not two yrs later the same thing has happened to those racks. Even tried these little plastic covers that are made specifically for this problem. They were virtually impossible to get on and didn’t last more than a few months.

My stove is approximately nine years old. During the past year both my husband and I enjoy cooking from recipes 3-4 times a week thus the stove has become essential. Functionality and size is important when trying to cook meals with two or three components. One of the oven racks was missing from the oven when we moved into the house. Even though it is self cleaning, spills pile up between cleanings so it is great that it has a really cool steam cleaning option. Just wish it were 5-6 years newer.

Maytag never fails to please me. My dishwasher is so quiet I sometimes have to put my ear next to it to make sure it’s actually working. The inside is stainless steel (those are the quietest) and it has a child lock so my 2 yo grandson can push all the buttons he wants and he still can’t mess things up. I love the high temp and sanitize features and everything is always clean and dry when done. It seems like it takes a long time to run through all the cycles, though. That and no adjustable top rack are the only two things I miss with my previous dishwasher.

I am very frustrated and disappointed with all of the appliances I purchased from Maytag, 3 1/2 years ago. The stove has never cooked evenly, and they replaced both heating elements, and it still does not bake properly. I just called customer service, because my pies for the holidays burned once again. They told me there was nothing they could do. I cannot believe a customer that spent this much money with Maytag (purchased a washer, dryer, microwave and oven), gets no help from the company. The transmission has been replaced in the washer, and is still noisy. The dryer is also very noisy. The stove does not bake properly, and the microwave quit within a few months of purchasing. The quality of Maytag is very poor, and the customer service is obviously poor too, when they said there is nothing they can do for me. I guess they do not care about customer loyalty.

We just had the same problem as most of you have posted. The control panel malfunction. Model MDB7749SBM. Our issue started after only 18 months when the dishwasher would start on its own and/or cancel a wash on its own. I think this is a major issue if a home appliance can start on its own from the off position and run through multiple cycles. I think this could be dangerous if you are out of town. Our cost to replace the panel was more than 1/2 of the original purchase price. This is a major defect and should be handled by Maytag if they are a company with any integrity.

I bought a Maytag dishwasher, stove and refrigerator and the dishwasher was a problem from the beginning. Repaired out twice and replaced the control panel. Seasonal residence, so the start of year 2 (this week) the control panel goes a third time. Its going to cost $387 to repair (told my elderly mother) and it turns out it was a warranty program that she purchased, not a repair estimate. She was misled as she called Maytag and they transferred her to a warranty company, and once again Maytag says theres nothing they will do. Now, Im hassled with cancelling that as well. I called Maytag and they dont stand behind their lemon of a product and said there is nothing they can do because its out of warranty (even though theyve been out twice to fix it). Do not buy a Maytag product. This is the first complaint Ive every written and I am just shocked that Maytag doesnt stand behind their product. Im informing 100s of people to not purchase Maytag and they will pass along my negative experience as well, for that, I am sure.

I have a Maytag MFI2665XEW6. Im getting water on the floor by the bottom draw. It looks like the coil in the back is freezing up and then melting down to the bottom of the freezer and out to the floor. I dont know how to lower the temp on the door panel.

Purchase a Maytag Bravo XL Washer Model MVWB850YWO from a major Home Improvement store in January 2012 with a 4 year service plan. Since this time I had to replace a motor and 4 (that is right 4) control panels. Although I am covered under a protection plan, the cost of laundry services and an outage of 2 weeks for each event is very costly. This time I call Maytag for support on their product. Looking for someone to say that there is something wrong with this machine. I want to hear that their product should not perform like this. I was told from a supervisor in these words that Mrs. we only care about the machine the 1st year. After that you are on your own. When did Customer Service lose the service part? When did companies stop caring about their products they produce? I never heard I am sorry youre having trouble or even a recommendation. A machine this new should not have 4 control panels replaced. This is the reason no one wants to buy a Made in the USA product anymore because we know the employees working there do not care about keeping customer relations.