Maytag dishwasher, MDB4651AWW was purchased on 15/02/2010. Touch panel was replaced under warranty on 16/08/2010. Touch panel became defective on 04/07/2012. It was $103 for the service call: panel was not replaced (too costly, > $200). My 2-year old dishwasher is now useless. The touch panel on this model has failed twice in two years and is obviously a design failure. I would ask for a free replacement panel.

I purchased a very expensive set of Maytag washer & dryer (topload washer) and heavy duty larger capacity. Firstly- I purchased this through Home Depot on Labor Day weekend and did not receive this set until December 2020. This set has all the electronics and Im going to tell you NOT to purchase either one. The dryer MUST have a metal solid vent. This sets your dryer out into the walkway of a laundry room. If you use a heavy flexible metal vent; your sensor will be going off constantly telling you your vent is plugged and to clean it. I had a dryer vent company out twice to clean and inspect the wall & roof vents yielding nothing. I also have a dryer vent cleaner which I hook up to my vacuum and I clean the dryer vent monthly. If you lose power. You will need to unplug your dryer and let it reset to be able to use it.The washer is also terrible for the outrageous price. Again; glass heavy duty top load with all the electronics. You cant get the washer to fill even on deep fill. Also; do NOT put a lot of clothes or jeans or blankets in this machine. It will not be able to level and spin. When you try to use the drain and spin cycle; the sensor keeps going off. I swift the contents around and around and finally end up having to take soaking wet cloths out into the garage until I have one sheet in the machine and it will spin out. In addition- the CLEAN with Afresh mess. This forces you to clean your machine- whether you are in the middle of trying to get clothes drained or not.Buy something thats a simple workhorse with one button. Stay away from any bells and whistles because its only going to cause you heartache in the long run. I wish I would have read reviews prior to spending $1,700 on a Maytag Washer Dryer set (ON SALE- for God sakes). This is the biggest piece of garbage I have ever purchased. Buyer beware.

I made the mistake of buying the stainless steel bottom freezer (model# MBL2258XES1) approximately 1 year before the freezer started to make a periodic clunking sound. The repairman responded because my year warranty was still active and found no cause for the noise. Fast forward a couple of months later and it started pouring water out onto my hardwood floors!!! Unfortunately it happened while we were away and my floors were destroyed. Maytag wants nothing to do with me. Im so disgusted. I now have to have a towel permanently on my kitchen floor. Nice. I made the unfortunate mistake of buying an Amana dishwasher recently not knowing that they were also owned by Maytag. The dishwasher is a water waster :( This is very disappointing - you try and buy American and you get screwed. If any lawsuits start up, sign me up!!!

I have bought 2 high end top loader models (Maytag centennial commercial), brand new both from Home Depot. The problem is Maytag is making them cheaper! Suspension is coal springs that suspends the load so if you fill it up, it lowers the drum to the floor, instead of a bottom bracket that supports the weight from lowering the drum to the floor! Second is the pulley system with the belt drive that wears through the plastic casing. You know some people dont have $900 or $1,000 for a machines that says commercial or heavy duty that only last 4 years when you have a family of six! Very very sad, will never buy another Maytag.

Bravo XL Washer & Dryer - I have owned this set for just over 90 days and have called Maytag several times just to get insulted. The customer service representative is not helpful at all, and tells me that I am not using HE detergent or that I am using too much HE detergent. Furthermore, they tell me that if a service technician comes to my home and nothing is wrong that I will get charged. So much for the extended warranty and what is wrote on the Maytag site. I explain each time that I am using name brand HE detergent and the recommended amount. The soap dispenser in the machine provides a fill line that I fill to. I have even tried using less detergent as recommended by the appliance store that I purchased the machine from, and still the washer does not clean my laundry and leaves residue on everything. I have even tried using the extra rinse, and extra heavy soil setting which does not make a difference at all.The other concern is that the clean washer feature light flashes weekly. I have purchased the cleaning tabs recommended to clean the machine, and run this clean cycle every time the light comes on. The dryer does not work all that well either and shuts off before the laundry is dry. Sometimes the dryer will show an error of airflow restriction or low airflow. This is confusing because the dryer vent and hose are clean, and the lint filter is also clean. This is so disappointing because I thought Maytag had great products. However, as I read other reviews about these machines and the customer service representatives it seems that there is a systemic problem with the machines and the customer service representatives that needs to be addressed by the leadership at Maytag.

Maytag has really gone downhill. Had trouble with a factory defect in a new French door Maytag refrigerator within a few months (had it returned) and now the Maytag Centennial EcoConserve Top Load Washer no longer spins after only just barely 2 years of use... I will NEVER buy Maytag again. That is a promise. I will put more money and buy more expensive products from your rivals if it means avoiding Maytag products. That is my advice to anyone reading this review. The washer was used for MAYBE 10 loads of laundry per month... Yes, just for two people who have desk jobs so It was never stressed out. Used HE laundry detergent. Quality is a thing of the past for this company. Your reputation is in the doghouse.

The dishwasher would not start July 30 2015. Tried to get service around here and no shops could respond. Called Midsouth Distributors for circuit board. They did not have one but would order and gave me the part # W10595570 based on the Model # MDB7749SBW3. Hoping could find one quicker somewhere else. Ordered one overnight from Sears and planned to replace the board by myself. However, I noticed the flat wire with 14 wires in the ribbon cable had brown spots. From my experience in the electrical systems, I realized this must be shorting out the start signal to the dishwasher logic controller. Sure enough, after scraping this off with a sharp knife, I was able to start my dish washer.My previous MAYTAG lasted 20 years. I bought this one in February 2014 at Home Depot. The design for the electrical controls is obviously very poor as testified by so many angry owners. MAYTAG should be required to replace all these control panels with a improved design at their cost. I hope this obvious poor design of a part gets attention in the United States and ConsumerAffairs will help us. I have called 1-800-688-9900 and registered with MAYTAG a complaint about this poor design.

The Maytag Bravos XL Gas Dryer I purchased less than a year ago has stopped working three times. The dryer stops producing heat. I am now about to call Maytag repair again and waste time and energy setting up a warranty service call. I spent a lot of money in order to go to the Laundromat on a Sunday. Do not purchase this dryer if you would like to be able to dry clothes at home with any type of consistency or confidence. Arrrggg!

We had a Neptune Maytag for over 12 years, best machine ever but this one (Bravos XL) is complete junk. We have been very disappointed in its ability to clean clothes with the length of time to complete its cycles is ridiculous. Its always out of balance with just a few pieces and lack of water twisting everything in knots. Well 16 months after purchase here we are with a broken machine, we have a fried circuit board. Maytag has lost our business permanently.

Should have researched before purchasing our Maytag Bravos MCT washer! We purchased it at Home Depot and it was delivered and installed by a certified technician. From day one it has been so loud and obnoxious with the way it “knocks” and “clicks” when it runs through a cycle. When it spins the whole machine shakes viciously, despite being balanced properly at installation.We have owned this washer just short of two years and for the last 8 months we have had to keep unplugging it to reset it so that it will even run through one cycle. The most recent two months have been extremely frustrating, due to the fact that not even troubleshooting can aid in “fixing” the fact that this piece of crap washer will not complete a wash cycle! It either stays in sensing mode & doesn’t add water, or it adds water but doesn’t do anything but sit still for about 15 minutes and then drains all the water back out and stays stuck on “wash”. We are researching online and have found many similar complaints with the same negative experiences. Our next step will be to call a repair person! What a crock!!! Maytag gets a big “thumbs down” from us!!!!

I bought model MDBM601AWB3 in October of 2009. The control panel and wiring harness burned in August of 2011 after, at the most, running twice a week. I called customer service and talked to numerous people. All said, Too bad, out of warranty. I did a quick Google and learned it is a common problem and even a fire hazard with Maytag dishwashers. My wife, who was being treated for lung cancer at the time and was very emotional, got a hold of someone in corporate and literally cried that we could not afford the $600 to fix a problem they knew it had when they sold it to us. They relented and agreed to pay for parts; we pay labor. Today, 1/10/13, the control panel is dead again. I suspect it is the same problem as all they did was replace the panel and wires. This machine has obvious dangerous design flaws that they were aware of. I find it sad that a company can screw people like this and get away with it. What recourse do we have now?

I have had my washer and dryer for about 5 years. After a couple of years, I noticed my washer would fill and stop. When I go to put clothes in the dryer, it’s still filled with water... very inconvenient! I have to open and close it and then it continues. The dial doesnt work properly! The delicate cycle hardly works... that started after about a year. It just freezes up and stops. I have to open and close it. It does not rinse right, leaves a film on dark clothes, and I have to rinse again; I do not over fill it either. Sometimes it does smell a little mildew.The dryer knob does not work properly. I set my setting and pull the knob out, and it doesnt come on. I have to do it several times or change the setting or put it on 30 minutes only... very frustrating! I never had these problems with my Kenmores! I wish I did not switch brands. These things should work properly. I realize washers and dryers dont last like they used to, but come on! They also cost so much more than they used to. I wont do this again. I will do more research as to what is a good product. Too bad!

I purchased a new Maytag washer (Model# MVWC565FWO) from LOWES 18 months ago and the paint is bubbling on the inside of the door. Neither Lowes nor Maytag would do a thing. We have spend many $1000s at Lowes and considering the replacement cost is only $126 for a new door I can see Lowes following Sears for their lack of customer service and diplomacy in matters like these.

Bought a new Maytag dishwasher in July 2013. In December it quit working and the problem was the control panel. The service tech knew automatically what the problem was when he arrived. It is now May 2014 and the control panel has gone out again. Contacted Maytag and was told they will extend the warranty another six months from the original warranty. After reading that this has been offered to others with mixed results I have my doubts on whether it will be honored. This is our last Maytag appliance.

I had a problem with my 1 year old oven. I scheduled an appointment and no one showed up. So I fixed it myself. A week later they called to schedule an appointment and I told them that they were scheduled for last week. So their response was OK, I dont need them anymore - goodbye. The parts are under warranty so I send them the part I replaced myself and the invoice for the cost. I didnt get a response. So 3 months later I send a second letter. Three more months and still no response. I can remember when Maytag had commercials showing their repair sleeping because they had no work to do. Now, their products are failing and their entire service depart is asleep.

In the process of self cleaning mode, oven died with door locked. Thermostat and thermal fuse went out, couldnt get oven door open or control the situation in any way except pray for no fire and wait for hours till oven cooled down. Door could not be opened, it died in lock mode. Called repairman, already in to 2 repair bills, still not operating. Called Whirlpool and Maytag, no help!! But amazingly they have created a new kit for the blower unit in this oven, model # Mew7527AW00. I paid a bunch of money for this oven, which replaced a 40 yr. old oven that had been in its place, operating fine, but it was Aqua Blue!! Its so sad that a huge Company as this will not help with an almost new Oven??

So far we have replaced the belt. Clothes have never come out clean. High Efficiency... Yeah, we have to put it on extra rinse to rinse all the soap out or wash twice because the clothes just do not get clean. Now it stops right before it drains after the wash. So I had to pull out clothes and use pitchers to get water out before we could tip forward and pull hoses to drain the rest. We checked hoses and connections. All lights work, it did a wash cycle, and again stopped before the drain. Really. All I got was “Didnt you take out the extended warranty?” Well, No I did not. Why would I consider the fact that MAYTAG would need repairs within the first 3 years. Its not like I do a lot of wash. Or have big bulky items. I have a laundry mat close by for that stuff, because it wouldnt get it clean anyway. Never again…

I purchase a Maytag dishwasher from Home Depot on 12/31/11. Based on the their commercials, I thought they were dependable. I did purchase an extended warranty, as I always do with any new appliance. After 2 years, the dishwasher stop working. I contact Home Depot and the extended warranty and was told to contact the manufacturer. Maytag blamed the extended warranty for the problem. They told me they could not help me. And could not help me. I will never ever buy any appliances from Maytag again. This model is M936/110V cord.

Has had problems with machine being off-balance and clothes getting clean. 3 years and now the machine is broken. Too costly to get repaired. Warranty only covers very specific things. Have had Maytags repair person come out and he did not access the problem properly. What a waste of time and money! Says it needs a very expensive part which with labor and parts cost almost as much as machine.

H.V. Board failure on Maytag model #MFI2568AES refrigerator. Whirlpool needs to step up their parts program. This refrigerator has been down for over 6 weeks and part will not arrive till 7/10/14. There is no excuse. The Maytag name is about as good as our country gone to H_ _ L in a hand basket. Consumers should not have a wait on parts or repairs that forces them to buy a new appliance when they spend $2500 and it only last a few years and try to contact them, they wont reply. I hope everyone who reads this considers LG, GE or SAMSUNG and not whirlpool excuses and JUNK.

My husband and I purchased a new Maytag dishwasher in March of 2012 at a cost of around $650. There is only the two of us at home and I only run the dishwasher 2-3 times per week. On June 16th, I went to run the dishwasher and it would not turn on after hitting the start button. The cycle buttons lit up but the dishwasher would not start. I called the service number in the user instruction manual and talked to a service representative. I was told that the electronic panel that runs the dishwasher is not covered under the 2nd-10th year limited warranty. It would cost around $291 to fix including parts and labor. When I asked for a qualified Maytag repair service company in my area, she only had one company to give me. This company does not have a very good local reputation so I preferred not to use it. My question is - How can a part that runs the dishwasher not be covered under the warranty? If the start button on the control panel is defective then the machine will not work. I also have a model MDB7749AWW2. After reading some of the 356 complaints about this very dishwasher, I think the Maytag Company must be well aware that there is a problem with this machines control panel and they are choosing to disregard the customer. My old dishwasher was a Kenmore and it ran for 27 years and I only had to replace the motor once. I will not be buying anything Maytag in the future.

Absolutely the worst washer I have ever had. I have read some of the other reviews, wish I was smarter and checked this out before spending my hard earned money to buy this washer. My washer also is rusting at the top where the bleach goes. I never close the lid when not in use my basement is dry AND I never use bleach??? My clothes come out they are a tangled up mess. When I go to hang them they are partly dry. It isnt as though I stuff the washer NEVER put more than 8 shirts in at a time yet they all come out with dry streaks like that part of the clothing never even got wet. We all know what happens when you leave a tissue in your pocket and it goes through the washer... Well not with this washer the tissue sometimes came out as dry as it went in. HORRIBLE product. I want the old agitator/I SET THE WATER LEVEL type back. It takes forever to get laundry done. They should take these OFF the market and give us poor consumers some cash back.

I purchased a Maytag dishwasher for $500. After several months of it working less days than not working, I contacted the repairman. I paid $350 to replace the control panel. I wish I had just replaced it with a reliable product. 1 year into ownership and the seals on the door are falling off. May I suggest never purchasing a Maytag product?

Pump motor went out after two years and all Maytag would do was a small discount on cheaper model. We paid over $800 for the dishwasher and to fix it was over $500 plus the 5 minute service call of over $100. Very poor customer service and a lemon of a dishwasher. Now we have a GE.

White clothes come out with some sort of grease stains on them and darks come out with a detergent white scum on them. I have to put them through twice to get the scum off and I have to scrub my whites by hand. So much for your new type washers. If I could find a washer with an agitator and water saver on it, I would buy it in a flash and get rid of this so called newest thing on the market. I have to put a cleaner through it every 2-3 weeks that costs me $10.00 for 3 pucks and having to rewash my clothes does not save water or time. There is a lot to be said for the washers that had water saver on them. First of all, I could open the lid during the wash cycle and add another item. (2) I could use the last of the 2 rinse cycles from my white clothes to start a load of dark clothes, that was truly a water saver and both loads were sparkling clean. Every women that I have discussed these new machines with (both front loaders and top loaders) say that you and other companies that think you have improved wash day for women have definitely not improved it but rather made it a nightmare. Absolutely hate this product. I hasnt given me a moments satisfaction since we spent the $1,000.00.

DISHWASHER MDB7749AWM - We purchased this dishwasher from Home Depot on 10/15/2011 for $630.00 for my birthday and yesterday the start button stopped working (cycle lights still work). We went online to look for more troubleshooting options and we found lots of complaints about faulty control panels. Sounds like thats what we have. VERY disappointed in Maytag for not correcting known issue. My dishwasher is only 3.5 years old and there are only 2 adults in our home. We run the dishwasher 1 to 2 times per week meaning this Maytag dishwasher will only last for about 200 wash cycles. Shame on you Maytag!

I have always bought Maytag products, but I will never buy another one again. This washer is the worse. It never has gotten the clothes clean and it is so loud. It has gotten worse. I called someone out to look at it and now am being told that the bearing is going out. We havent had the washer for two years. The cost to repair is going to cost us $574.00. That is crazy. We are going to let it go out and buy another washer, but NOT a Maytag. I will do my research before buying a new washer.

We bought Maytag Dishwasher on October 9, 2019. Due to the installation difficulties we were not able to install and try it right away. Lowes warranty expired in 30 days, and the dishwasher is not cleaning the dishes. Even with the hand prewash of all of them-they come out dirty. I have to clean them after. The dishwasher is very weak. We contacted Maytag and were told that they can do nothing for us, only send technician (we have to pay $160 per visit). We can not return or replace it, the quality is very poor, so we will have just to buy a new dishwasher and lose 500$ for this product.

We bought a Maytag 2000 Series machine about 2 years ago. At first the machine worked great, as a new machine should. Then, after about 7 months water started pouring out of the top dispenser for detergent. I read the manual and looked online at the Maytag website for common problems. It said that sometimes small clothing gets sucked through the hose and needs to be unclogged. I followed the instructions to fix the problem. It worked fine for about 2 weeks later during the middle of a load the machine would stop and give me error codes. I looked these codes up and now I have another clog on the drain tube that needs to be fixed. Lo and behold these 2 problems have been continuing ever since. I cannot do a load of laundry without getting a code and having to take the machine apart. I called Maytag to explain my situation and the customer service representative said that because I fixed the problem myself at this point there is nothing that can be done. They do not guarantee that their equipment will work nor will they help solve the problem. I cannot believe that we spent so much money on something that I cant use. Not to mention the fact that when I do complete a load some of the clothes are ruined by the machine ripping holes in them. I would not recommend buying a Maytag because they dont care about customer satisfaction or the quality of machines they sell.

I have Maytag Neptune washer and dryer that was purchased in 2002. Theyre still going strong. Its a great size for empty nesters like us, but if you have a big family, you might want to consider a larger capacity.

Dishwasher (MDB7709AWB2) stopped running mid-cycle, internet search revealed that control panel needs replacement at a cost of $135. excluding labor, for a dishwasher that originally cost $348. Notified Maytag and am awaiting a response.

We purchased our Maytag Refrigerator brand new, about 18 months ago. It always ran loud so the repairman came out during the 12 month warranty period. He told us to unplug and reset it, but that never did the trick. Eight months later, the fridge stopped cooling. We called our local repairman and he told us ($97 later) that the compressor was out. He said we should contact Maytag because the compressor should be under a 5-year warranty. Then the nightmare began. I spoke to four different reps with a total hold time of about 2 hours. Two of the reps put me on hold to get a supervisor and/or consult another rep and I was mysteriously cut off each time. One rep told me my compressor wasnt covered under warranty. The last rep I spoke to told me it was covered and he scheduled a Maytag repairman to come and replace the compressor. I was thrilled. The repairman came out and informed me that the compressor was indeed out and handed me a bill for $137. I asked why I was being billed and he said because that was the way that Maytag had ordered the service call. I told him that the Maytag rep had assured me that Maytag was covering the repair. He apologized and said that not only was I obliged to pay for the diagnosis (which I didnt need because I had already paid my local guy for the same information), but that it would cost $900 to replace the compressor. I was flabbergasted. I called Maytag and they denied all responsibility. They said that even though the rep had assured me of Maytags commitment to replace the compressor under the 5-year warranty, he had made a mistake and I wasnt actually covered. So I paid our local repairman to replace the compressor, because by that time, we had been living out of ice chests for 2 weeks. That was 3 weeks ago. Now the unit is freezing water on the bottom of the freezer and then leaking water on the floor. It is unconscionable that this company be allowed to defraud people to this extent. I will never buy a Maytag again and I would like to be informed of any class action suit. This company should be deeply, deeply ashamed of itself.

I bought a Maytag Gemini double oven gas range 5 burners (model MGT8885XS000), even air true convection cooking. Within 4 months, 1 of the gas valves (knobs to turn gas on with) froze. I could not turn one of the top burners off. Maytag came out and fixed it. Three months later, another one froze. Again Maytag came out and fixed it. Our warranty ended. Over the next year, all five burner valves have frozen. I called Maytag, told them what happened. The most they could do for me was to give me the part half off. So I can pay $200.00 for parts and pay for a repairman to come out and fix it. The oven cost $2,000.00. I am still paying for it. Chances are if I repaired it would break again.

Maytag Quiet Series 200 only 1.2 years old: I moved into my home about 2 months ago and the touch panel on the dishwasher, which is of course just past the warranty expiration date, has progressively gotten worse until now, doesnt work at all. I have tried calling Maytag many times on numerous occasions, who apparently only has one phone line because its ALWAYS busy. The cost for the touch panel on this dishwasher (model# MDBH945AWS3) is $150 which isnt even worth fixing since I can go to Lowes and buy a new FRIGIDAIRE for $300. The problem is the circuitry from the touch panel to the control board gets too much moisture in it with no protection around it. If I were them, I would find a way to make all these parts separate so regular people, like you and I, would be able to buy parts a lot more cheaply and repair these items ourselves. However, since the front panel and the circuitry attached to it is all one cohesive unit that cant be taken apart from one another, nearly at all without ruining it, then I might have been posting a different review here. However, that is not the case. IF I could actually get in touch with Maytag, I would ask why on earth isnt this a recalled item and when they are shipping me a new part since it seems everyone is having the same issue with their Maytag dishwasher, no matter what series it is. I do not plan on buying a Maytag appliance in the future. I do plan on buying a Frigidaire since the rest of my appliances (stove, fridge and overhead microwave) work perfectly without any issues whatsoever.

We purchased the washing machine (MVWB400VQO) on July 9, 2009. Now we must buy a new washing machine as this one is apparently beyond repair, or else the repair costs will far exceed what it would cost to purchase a new machine. We are completely disgusted with its failure, as we paid $822.36, with the delivery fee and the tax. We expected that this machine would last for years, but here we are, 42 months later, having to again invest in a washer. Now that we have a computer and are able to browse your performance reports, we wish we had been able to read them before, in which case we never ever would have bought it at all.Yesterday it spewed water all over our basement, flooding things that should not get wet, providing an atmosphere for encouragement of mold and rust. The motor is gone as the housing is cracked, which was caused by debris getting into it, something that we could not have known or prevented. This is very poor design by your company, in our opinion. We called some repairmen, all useless as apparently the whole machine would have had to be completely dismantled at a rate of $84.00 per hour, and he could not tell us how many hours that would take, to say nothing of finding a new motor for the thing.We will never again buy a Maytag product as they are expensive with a too-short shelf life and there’s nobody who cares when you need help for something that should not have happened at all. I understand Maytag is really not the good old dependable Maytag we used to know and love at all, but rather is now owned by the Whirlpool Corporation, whose products we will never purchase either.I know why that lovable old Maytag repairman we used to see on TV is retired. Its because he could no longer stand the quality (or lack thereof) of the appliances that you are now producing. He is probably home, hiding his head somewhere and hoping nobody will recognize him. And what, kind sirs, do you have to say about this? Thank you in advance for your prompt reply.

Purchased Maytag 3000 series washer and dryer in June 2009. Like many other reviews, the washer is making a terrible loud noise during the spin cycle. I contacted Maytag customer service and was told wait time is 10 minutes and opted for the call back option. Received a call back from an agent located in Tennessee, United States and he checked for recalls or projects and found nothing. Offered a technician call in my area for $112.00 for 30 minutes to diagnose the problem. I told him that if he checked on the reviews, he will see many regarding this problem and a bearing issue at a cost of up to $700.00. The Maytag repairman is not only lonely but out of business and Whirlpool bought them out. I would never again purchase Maytag or Whirlpool products. We are seniors and do not abuse our appliances and why do they not last at least 15 years. Talk about disposal washer machines, who can afford to purchase them every few years. The washer sounds like a jet going through our house when it is in the spin cycle.

We purchased our range in May of 2012. It is now November 2014 and the stove has had three brains, three ignitors in the oven and one ignitor in the back of the stove. When I set it to bake at 350 degrees, the oven heats up and I put the food in the oven. When I go to check the food, I find the oven stone cold and the brain is still displaying 350 degrees. According to Home Depot Warranty department, if the oven has been fixed three times for the same problem, then the unit is considered a LEMON. Ok, what about the three brains? What about the three ignitors? The ignitor in the back of the stove controls the oven as well. SEVEN times for a technician to come out and fix my LEMON stove is ridiculous. California has lemon laws. I will file suit against Home Depot, Whirlpool, A&E and Quality Appliance if this stove is not replaced within the next seven days. IT IS A LEMON! I have lost way too much food in this oven because I dont know when it shuts off.

I purchased a Maytag refrigerator (MBR2258XES4) from Home Depot in 2012. I bought a five year extended warranty. It started leaking at the bottom. Repairmen said defrost drain clogged not covered! Cost: $180. DO NOT BUY MAYTAG, N.E.W. (Asurion Co.) warranties or Home Depot appliances! This is text book deceptive advertising. At no time did Home Depot associates in Kitchen and Bath departments say that this common design flaw existed and that it was not covered under the N.E.W. Asurion warranty which cost me an an additional $150.00! I am interested in joining a class action lawsuit against Home Depot and Asurion Co (N.E.W.) warranties.

Thank you all for taking the time to write these reviews. My only regret is that I am reading it now, I wish I would have read it before purchasing my own Maytag washer and dryer... I bought a Maytag MVC565FWI / YMEDC555DW1 washer and dryer duo in December 2018. I had some holes in my sons clothing, but thought maybe they were due to him being a boy of 17 year old in college, sitting all day... Also my dryer was barely drying.Called and had a 1st technician for the dryer issue. He said no wrong code and to try and clean the evacuation vent. As I am a renter, I contacted my owner to do so and he did. But I did not get to try the machine unfortunately since 5 days after the technicians visit, I was deploying to Africa. I am military and was deployed for 8 months. Upon me return, dryer still barely dries and HOLES in every load of laundry that I do. My sons and also my own clothing. This time, there is no mistaking articles that I put in came out with huge circular holes.A second visit with a technician is arranged, last Tuesday October 8th 2019. Still no codes are found. And technician suggests cleaning the conduct better. Again my owner does so. Again, up to 4 cycles of 60 min on High heat to dry articles. No economy on energy on these models! I have called Maytag today since no one has contacted me in a week for my wrecked clothing. To my request of having my appliances either replace or refunded, they say no. Policy is to send a technician. Again. After 2 visits of technical support, Maytag is sending me for a 3rd time a technician (at my cost if nothing is found again) to test the appliances. Since the technicians can not find a code on his machine, Maytag is telling me they will do nothing.I have a washer dryer that wrecks my clothing and does not dry them. (Also I feel like my clothing are never fresh scenting, I wonder how efficient they are with even the basic cleaning part..) I will have to put them in the garbage, because how can I sell them?! Talking to Maytag, is being treated like an infant that does not understand THEM, when in reality, they do not back their products at all. I feel left alone with brand new machines that have been used around 30 times in under 1 year, that I will have to through away in the dump and never ever buy from this company again. M.

I have had this refrigerator only 6 weeks. The freezer works but the refrigerator does not cool properly. I went back to Home Depot - Baltimore MD and told them I have lost 3-1 gallons of milk for it spoiled. I am right now putting a 4th gallon in and out of the freezer trying to keep it. A serviceman was to my house the other day and stated this brand new Maytag refrigerator only had in my home 6 weeks needs a new board and a flapper that opens up in freezer that sends cold air to refrigerator. Parts are on order. Home Depot would not trade a Maytag refrigerator that worked well and take this lemon back. I am stuck with a lemon I only bought 6 weeks ago.

This set of Maytag washer/dryer are nearly nineteen years old now and are still workhorses! They keep getting the job done time and time again! Absolutely no complaints. Absolutely and completely amazing!

Approximately one week ago, the display on my fridge began to flash and ice door flap continuously opens and closes. Upon researching the issue, it seems to be a very common issue and a known defect. One in which was apparently a recall at one point. I was told by a Maytag representative that the recall was from 2007 to 2009 and has since expired. Expired? Its a known defect and should be the responsibility of Maytag to provide the parts and labor to repair the fridge. I asked for a supervisor and was told that one would contact me within 24 hours. Well, about a week later, I never received that call so I called Maytag again. This time I was told by the maytag representative and a supervisor that there was no recall and that it was a Quality issue. A play with words, in my opinion. Anyhow, regardless of the title the issue was given, I was told I would be responsible for the repairs and costs. I attempted to look up the recall on Maytags website and had seen the last two letters of the serial number to my fridge listed under the recall, but when I tried to investigate further, the site referred me to the 800 phone number I had been calling. Now, had this been an issue that was not a known defect and apparently a recall, I wouldnt be writing on this site right now. But, because it is a known defect that maytag is aware of, I think its Maytags responsibility to pay for the parts and labor for my fridge.

This Maytag dishwasher is beautiful inside and outside. I love that the controls are hidden. It cleans dishes very well. It has a large capacity for dishes, a rack for glasses/mugs, a small rack for cooking utensils, and a container for silverware. It is so quiet you hardly know it is working. I would highly recommend it.

No problem with retailer. Problem is this top of the line Maytag dishwasher, Model# MD8895lAWW. Stinks all around. Takes long to wash and load, times are far apart and too few so holds few dishes. Dishes and glasses break because of the tine spaces. Horrible dishwasher for high price. I hate it so much it upsets me daily. All I get is a sorry from Maytag. Its not that old, only a year and a half. Why no satisfaction? I will avoid all Maytag products for life.

Maytag Smoothtop Double Oven - Bought this stove 2 and 1/2 months ago and already buttons arent working. Very disappointed, not getting a Maytag again.

Purchased the Maytag Bravos washer approx. 2.5 years ago. I cannot even begin to describe how disgusted I am with this washer. My clothes i.e. towels come out ripped on the edges, clothes do not get clean, shirts etc come out wrinkled no matter what setting used. It is not energy efficient because loads of laundry need to be washed twice if they are soiled (like our everyday jeans). Went back to the independent store where I purchased washer and was told to use only the bulky or gentle/delicates cycles to reduce rips in clothing. Such a complete waste of money, and it was not cheap!

My dishwasher racks are disintegrating. I called to see what to do or if there was a recall. I was told that problem happens a lot, but there is no recall or other option other than to purchase new racks. I could almost buy a new dishwasher. I bought Maytag so that it would last a long time with few repairs. That has not been the case with this dishwasher. I had a medium grade Sears’s dishwasher for years before I supposedly upgraded to a better dishwasher. Maytag is obviously an overpriced name and the quality of their product is no better than any other cheap dishwasher.

I am a Baby Boomer... just like so many of us, I watched those lonely Maytag Repairman television commercials. Yes, silly me I purchased our top loading Maytag Bravos XL because of the brand name and because the machine was large enough to wash our bedding. Well, like so many fellow purchasers have found, this machine does not get the clothes clean and leaves soap spots all over the clothes. Its embarrassing. Additionally, there is that funny smell after the clothes come out of the wash. Well, Maytag has really done a number on us all. Kudos to their research & development department for creating a washing machine where the clothes come out dirtier. Has Maytag thought about a RECALL? I will tell everyone I know to NEVER buy a Maytag.

Like everyone else got that French door fridge and was also duped on that 1 yr warranty - a 95 dollar repair visit for a 485 repair job on a 1200 dollar purchase. Shame on them. Im gonna fix my new floor and replace that frozen bottom, leaking on the left, non-working ice maker 2 yr old refrigerator. Very disappointed with the whole thing and sorry for all of our losses.

Our problem started when the control lock button locked itself on. Called Maytag and told it wasnt covered by warranty but they did walk us through resetting the power and it fixed the problem until we ran the next load. Now when you try and set it, the rinse only light comes on. Bought the Maytag because I always believed them to be dependable - wrong!! I had a basic model Whirlpool running for a family of 5 for 25 years prior to this Maytag without ever having to call a repair person. Maytag wont deal with the issue so I would recommend to anyone else having any issues with unreliable appliances to do what I am doing - boycotting Maytag!!

Maytag Dishwasher Model MDB 7749SAM0 - Bought this dishwasher from Lowes in 2012 for my daughter and son-in-laws new home. Thought I was making a good choice with Maytag. Wrong. Same control board problem that everyone else is having. Wiring ribbon is corroded and shorted. Why is this not a re-call? I will call Maytag and Lowes and complain, but likely will get no justice. Sounds like I should just bring this machine to the dump and take my losses.

I purchased a Maytag Centennial washer a few years ago. In my opinion it hasnt worked properly from the start. We went on the low end of price, because we spent a small fortune for GE products that broke after a year and a half. This Maytag hasnt been a much better experience. First it didnt drain and spin clothes, and I was told I was using too much soap. Cut back on the soap and it started working better and going through the full cycle but the clothes never felt or smelled fresh and clean. Now 2 1/2 years in, it doesnt complete the full cycle on its own, AND there is dirt in my washer after every load. My clothes come out with streaks of dirt on them. The picture below is of a pillow case I just took out of the wash! Ive cleaned the washer multiple times, but it doesnt drain properly so it doesnt help. Maytag charges a service fee just to come out and troubleshoot and charges you again to come and do the repair. Im running out of reputable companies these days with washers.

We bought a Maytag refrigerator serial # K11101146 and model # MBL2258XES1 on 5/7/2011. We started seeing puddles on the floor about a month ago coming from the bottom freezer. The warranty on the refrigerator was only good for a year. We investigated it further online and saw that a lot of other people were having the same problem. We found a video on Youtube on the solution, which was to tear the bottom frig apart (which is a pain and takes about 3 hours to complete) and to thaw out all the ice accumulated on the coils and run hot water down the drain until that thaws out. It makes a real mess. Now we see that this will probably have to be done again and again from others online who are having the same problem. We never had this problem with any of our refrigerators or any problem with them for that matter. Our last one was a 15-year old Amana and we wanted a more energy efficient refrigerator. We bought this one at Home Depot thinking that this one would last us for the rest of our lives. We are in our mid 60s now. This should not be happening at all especially as much as we paid for the refrigerator. I contacted Maytag and they more or less said, “Sorry about your luck.” I hope something can be done about this, especially for the amount of complaints filed. Unfortunately I did not take pictures but if it happens again, which I understand from other complaints that it will. Thank you.

We purchased a Maytag Gas range MGR8674AB in November 2012. The contents of the drawer (oven mitts, trivets, hot pads) caught on fire. As we pulled out the drawer, it scorched the front of the range.

I purchased this $857 dishwasher from Lowes in May, 2021. It broke in June, 2021. S&S Repair was sent by Maytag to repair. It took 3 weeks for them to come, then they discovered the motor and pump assembly had gone out. Parts were on backorder. It is now August, 13, 2021 and I still have no dishwasher. Lowes would not replace this dishwasher. Maytag will not authorize a return. This is disgusting.

I bought a Maytag washer (Centennial) because of its reputation. I didnt even realize this site was out here and would have made another selection had I known. I bought the washer on June 7th of 2011. On June 15, 2012, the washer just quit working. I called Maytag. They said since the warranty was over that I had to pay a technician to come out and it would cost $129. I was upset but I had to have a washer so I scheduled it. The tech came out and said the motherboard was bad. He said that this has been a common problem with this machine and that Maytag should actually recall the part. The replacement part was much better. He suggested I call and complain. The part was $180. He said that Maytag may reimburse me because it was so close to the warranty cut off. I called Maytag to explain the situation, and what do you think their response was? Since you already paid for it, there isnt anything we can do. Nice! What a joke. I will never buy another product from them and neither should anyone else.

We purchased a refrigerator in December 2010 with a 12-month warranty. Since the refrigerator was delivered, we have experienced nothing but problems. Most recently, there was a problem with the auto defrost causing us to lose all our food stored. It also caused water damage to our floor. We scheduled maintenance with a contracted company through MayTag. After three scheduled visits, which made me miss 3 and a half days of work resulting in an additional loss of over $300, our refrigerator is still broken and they just want us to schedule another maintenance visit. When calling Maytag customer service we are literally told, “your loss, there is nothing we can do to resolve your issue, we can only continue to send out maintenance.” I am so disappointed in this company, the product, the customer service, maintenance service etc.

My experience over the past 2 years with my top loading Maytag washer is echoed in almost every review here. 1. Not enough water to clean the clothes 2. Clothes come out still dirty and covered with detergent 3. Barely agitates 4. Repeated repairs for leaking and computer board breakdown 5. Complete lack of interest by either Lowe’s and Maytag when contacted. I could write a long, detailed complaint but it has all been said quite well. We need to band together and file a class action lawsuit against Maytag. Any lawyers out there willing to take this on?

I have nothing but great reviews for my Maytag experience... In approx 1975 I purchased a Maytag W&D, Model MAH4000 MDE4000, when their advertisement was portraying Maytag repairmen as the loneliest repairmen. Maytag was so dependable that the repairman was NOT needed...and it was true... That Maytag W&D set lasted til approx 1998 when it was upgraded to the Maytag Neptune MAH4000 series... Had a minor problem with mold in the washer, but Sears and Maytag replaced the seal and made another modification... We also dried the seal at the end of the washing day and left the door slightly ajar between uses... Have not again had that problem.I have since given the Neptune set to my daughter and the washer and dryer are still in operation, WORKING SUPERBLY I might add... So I am searching for a good quality Model MAH4000 and MDE4000 to replace my current much older, yet functional Whirlpool... It may need some repairs and about a year ago, I spent $173 to replace the Pump which was clogged by a sock inadvertently stuffed around the top of the drum when too many items were pushed in at one time. I prefer not to throw additional money at this machine! So, if you know of a Quality pre-owned Maytag Neptune washer and dryer in the Lexington KY area, please contact me...

My Maytag dishwasher is a nightmare. I purchased it in February 2013, started having problems with it turning off a week ago. I called Maytag customer service on Wednesday and was told I had a service call scheduled for Friday. I took the day off of work to be available for the repair service. I was given a phone number for the repair service. By noon I was wondering when I would receive a phone call to let me know when the technician would arrive? Then I was told that my appointment was scheduled for next Tuesday... ARE YOU KIDDING???? THAT WOMEN FROM MAYTAG CUSTOMER SERVICE LIED TO ME ABOUT THE DATE OF SERVICE!!!! I spoke with Scott, customer service representative (manager) and he told me that I was sent an email with confirmation. ANOTHER LIE!!!! I HAVE NOT RECEIVED ANY EMAIL FROM MAYTAG. I would never buy another Maytag appliance.... They DO NOT STAND BEHIND THEIR PRODUCTS. LOUSY CUSTOMER SERVICE... SUB PAR TO SAY THE LEAST!!! Very dissatisfied customer - wasted my time and are not willing to make it right.

MY MAYTAG WASHER and DRYER ARE 17 YEARS OLD. THEY are FRONT LOADERS WHICH I THINK MAKE A DIFFERENCE. I BOUGHT MAYTAG because I had trouble with Whirlpool products that didnt go the test of time. The only problem I have with my washer is the mildew.

On April 8, 2017 I was sitting in my Dining room with Dishwasher in the kitchen in cycle cleaning. All of a sudden I heard electrical sizzling and turned to see my Dishwasher was on fire. I got up and opened the door and my Husband shut off the circuit breaker for the Dishwasher. He raced to turn off water under sink and went to disconnect the dishwasher when all of a sudden hot water was shooting all over the place. I tried to catch in a bucket but it was so hot and shooting out hose fast. Kitchen and Dining room were then filled with water. He realized the turnoff under sink was installed at time of house built and cant be fixed without a lot of chopping up under cement.Well finally we cleaned up the mess with mop and towels and relieved neither one of us fell at our age. He unconnected the Dishwasher and secured outside. About 2010 there was a recall on this model Maytag. I reported it and a repair man came to change the cycle panel and said it would be fine, not. Yes almost 7 years later a fire occurred. Just glad we caught it in time without losing our lives or my house. Never, never again will I purchase a Maytag.

Maytag Dryer model # MEDC400BW. I purchased this dryer in March 2015 the fuse went out in August. It is now November and it is out again! I have been buying Maytag since I left home at 18. I am 62 now, so I have been a loyal customer because Maytag was a great product. Not anymore since Whirlpool bought them out! You have to call them to schedule a technician and then it can take anywhere from 1 week to 3 depending on when they get the parts because they have to order them, and nobody else can come out to work on it if it is still under warranty! This is so lame and just not right.

It meets all of my needs and expectations. Its quiet looks nice and does a very good job of cleaning dishes.

I totally understand the technology age. We need to move forward as a country and keep up with modern technology. But somebody please tell me why this means companies have the right to not stand by their products? Why do consumers have to pay the price for bad products and companies leaving us high & dry? My husband & I were excited to redo our kitchen. We bought all new appliances in November 2011 - all Maytag. In December 2012 (13 months after we bought them), we started having issues with the oven. The oven would not maintain the proper temperature. We called a service man in January 2013. He deduced it was the computer board so he replaced it. Cost to us - $350 (including service call and labor). Now, less than 2 months later, the same problem. Maytag, Whirlpool, Kenmore - whatever company you are now - rest assured, you will not survive if you continue to produce shoddy products and refuse to back them up. The service man is to stop by again tomorrow. I refuse to keep plugging money into a product only 15 months old. I will not buy another product from you again. I just hope the dishwasher, microwave and fridge make it to at least 5 years old. Isnt this funny? My grandma has a Maytag washer & dryer - 35 years old. You sure cant say positive things about your products today. Good luck to your future - youll need it.

I have bought Maytag products for years. I have a white Maytag microwave that is about 3 years old. It was given to me at 1 yr. old by my sister-in-law when she decided to splurge and create her dream kitchen and went with stainless. The door handle broke in the first year. We glued it. It just recently completely fell off completely-snapping at both ends. I am calling Maytag and attempting to have it repaired. I am otherwise very pleased with this appliance. I have had other microwaves for many years without this happening. Im hoping they will agree to repair.

Maytag washer MVWC565FW - Clothes do not wash. They just get pushed around and the soap scum is left on the clothes even with the water at the highest level. I bought the washer override lid switch at a appliance parts store just to observe the washer cycles. The washer did not wash the clothes. I took the washer back. I like Maytag products but this washer has to be engineered.

Bought a Maytag dishwasher (Model #MDBH979SAM0) three years ago. Four weeks ago the control panel wouldnt work correctly. No matter what cycle I attempted to select, other cycle buttons lit up. The start button did not light and the cancel button would not turn off. I called a repair guy, he came out and said Maytag was having a lot of problems with the control panels. He reset the machine and finally got it working again. He said he wasnt able to get a new control panel from Maytag due to demand/delay in manufacturing. Today the control panel went out again. Based on all the other reviews Im not sure its feasible to put more money in this machine. Ill research other dishwashers and get one that has a better performance record. DO NOT BUY A MAYTAG.

Ive owned my Maytag Neptune front loader since 2003. Since then, the whites have either turned gray or yellow. Ive tried minimizing the use of Tide HE, maximizing its use, and I still get the same results. Can anyone please assist me with this major problem? Ive owned Maytag appliances since the mid 60s, and I know the quality isnt there anymore.

Im currently standing in front of my washing machine waiting for the 13-minute drain and spin cycle to finish because once again my load didnt drain and finish right. Except it has already been 40 minutes and it claims there is still 9 more left as it continues to sit there doing nothing while it hasnt even started spinning yet. It Sat on 13 minutes while sensing for over 5 minutes, then 12 for 10 minutes while doing nothing, then it changed to 11 minutes and made some weird noises but didnt actually do anything for 15 minutes, and now the timer randomly changed from 11 to 9 without any noises or movement happening and now continues to sit here.I stupidly thought I could spin my clothes real quick to throw them in the dryer before bed and now I stand here extremely tired and very irritated. I also have no doubt some of the clothes will have holes in them when theyre done because they always do, my family looks like were homeless and ratty half the time we get dressed now. Also it never deep cleans thoroughly even on the toughest settings, I swear our socks can be washed 3 times in a row after being soaked all day and still come out crusty or a lot of times the armpits of shirts will still smell or be ultra stained with deodorant marks still.This technology is almost too advanced and everything is decided by sensor, regardless of the registered functions on the buttons it will still do what it wants as the sensors see fit and run when they decide everything is perfect and ready, including taking 10 minutes just to unlock the lid when you pause a load cuase a small child may drown in the foot of water or a person may have their life completely altered by getting a little bit wet if the machine isnt completely drained and in pristine condition before you open the door. This machine is terrible. This company is terrible. And worst of all they drain your wallet for these horrible contraptions. I wish I could rate this 0 stars.

This has been the worst washing machine I have ever owned!!! Purchased 3 years ago and this is the 3rd time the bearings dont work again. It make loud clanking noises. Then fails to spin at all. The first time it broke was the 1st year we owned it. It is sitting in our hallway and I can hardly wait for it to leave my house. Talked to the local appliance dealer and they never recommends these washers. I told dealer I must have gotten a lemon. He replied that it wasnt a lemon, that the machine tubs have gotten so much bigger and they have needed to upgrade the bearing system and are unwilling to do it. Dealer has highly recommended the Speed Queen. Based on the stellar reviews that is what will be coming to our house today. I can hardly wait. I know, its just a washing machine but frustration has overcome me. The Speed Queen has no plastic parts. We went with the knob style as opposed to the electronic push buttons. Less to go wrong. The warranty on the Speed Queen is top of the line, 5-year parts and labor. The salesperson didnt even try to sell me a warranty. No need to. Speed Queen stands by their product. I only recommend the Maytag Bravo XL if you dont have enough stress in your life.

Whos up for a class action lawsuit against Maytag? I believe Maytag is making claims that are NOT true. I bought a new Maytag Bravos XL in Nov 2015. I asked the salesperson to point me to a deep water washing machine for Large loads. Salesperson sold me the Maytag Bravos XL MCT and made claims I would have 30% more water than the other washers. The sales pitch (according to Manufacture) is these smart machines have sensors that can detect how much water is needed. THIS IS NOT TRUE. My Maytag machine only gives me 1-2 inches of water on the normal and rinse cycles and maybe 4-5 inches on deep water cycle!!! Certainly not enough to cover clothes, towels or sheets. I immediately called Sears. Tech is basically being trained to tell consumers thats the way it is. This is the new future in washing machines. So, My recommendation - hire an attorney to get your money back!

Purchased a Maytag refrigerator less than two years ago. Model M1txegmyb that was nothing special. Main purpose was to keep food cold/frozen. Now it makes noise and will not freeze anything. We called Maytag and they told us to take a hike or pay $469 for a new compressor on a fridge we spent $650 on. I would never buy their products again because the quality is so poor. Reading the other comments we have decided to throw the unit out at this point as we have pledged never to give Maytag another dollar.

I purchased a Maytag washer the centennial commercial technology model about 4 years ago. At the just barely 2-year mark it needed an all new transmission (Approx $800) Thank God for extended warranties. Now it is doing the same thing again making terrible noise. For a purchase of $1000 this is not good quality or decent workmanship And Maytag does not stand behind their product. I guess I need to buy another brand from now on. Please beware of very costly repairs with this one.

The washer I bought brand new has never worked well. The clothes end up all bunched and twisted up together. The bleach is not distributed properly, I have big blotches of white spots. It is leveled, still shakes and everything is on one side

Maytag Bravos XL MVWB980BGO. To start, I live on an acreage so some problems may be related to being on well water. The most annoying part is the washer doesn’t have a drain & spin without rinse. So, when my well pump started acting up, I had no way to just drain & spin off the load, so I had to try to lift thoroughly soaked clothes and try to dry them...which took about four hours. Another aspect that is a pain is uneven loads. It keeps trying to fill, instead of just stopping & letting me adjust the load myself. Then the damn thing won’t reset. I often have to resort to unplugging the machine and starting over. High efficiency is a joke. I’ve had the machine about five years now and it goes low flow error, even though the flow is fine. I’ve tried running cleaners through the water line and it’s still doing the same thing. The only thing left to try is take the machine out and try and manually go through the lines. For the amount of money we spent on this machine, I am thoroughly disgusted with how it runs. It is the first & last Maytag washer that I will ever buy. Next time, I’m buying as cheap & basic a machine as I can buy. On the upside, the dryer works perfectly.

So far, so very good. This is the first time owning/using an electric oven. I just love my Maytag. It was affordable, especially since it was a combo sale with the over-head matching microwave from Home Depot. Two years later and it's as if I just purchased it. Wonderful, wonderful, wonderful.

So far after 5 calls and over two hours spent on calls IMPOSSIBLE to get an answer from Maytag about the correct fill levels of detergent. Consumer support simply do not know and refuse to direct me to anyone or have anyone call that does know answer. WHY SO IMPORTANT? Either you do not get clothes clean OR you damage machine and leave residue on clothes! Neither is acceptable. Using the fill level indicator on Bravos XL dispenser is in direct contradiction to any recommended levels on lids of high efficiency detergent manufacturers like Tide. Per Maytag manual only fill detergent to max fill LINE which is literally about two or three tablespoons of detergent. The lowest possible quantity of Tide per the lines on lid even for smallest load is two or three times the recommended fill level on the dispenser. No one has to be an engineer to know two tablespoons of HE detergent in dispense is going to do same effective cleaning for one shirt or towel as it will with a queen size comforter or very large full capacity load. CORRECT ANSWER DETERMINES IF YOU DAMAGE WASHER OR IF YOU HAVE DIRTY CLOTHES. Googling online there is also no answer. Such a critical answer for Maytag washer to work and clean clothes that is simply not available and documentation is wrong is a huge concern about the viability of this machine and worse their support. Our machine is less than two months old but is obviously over-engineered to the point of just being silly. Tip to Maytag: start selling washboards. More energy efficient, more green except for red and blue bruised knuckles, uses one tenth as much water and users do not need to spend their nest egg savings to buy. Not the first but will be the last Maytag product we will buy. Name may be same but the company is definitely not the company that used to enjoy that name with pride. SUMMARY: Maytag is adamant about using the correct amount of HE detergent OR damage and bad performance by washer and dirty clothes with a detergent residue. With all our best efforts we cannot get what that quantity of detergents is supposed to be. The user manual at best has ambiguous answer. The manual suggest horizontal measure of detergent in tray to max fill level which cannot be right. IF you instead use a vertical measure of how high detergent level comes up to the max fill line the quantity is radically different. It says dispenser holds 3 oz which would be beyond max fill level but nowhere near a vertical fill level.

Maytag dishwasher model MDBH949AWW - I purchased a dishwasher thinking I was buying the best (laugh is on me). The date of purchase was 1/18/10, the control panel was replaced on 5-25-11 at no charge. On 10-15-12, the control panel failed again so I was forced to hand wash an entire load of dirty dishes. I used the dishwasher once a week. I am debating if it is worth it to repair it or replace it, in light of the fact that it could go out again the next year. Wish I had found this website before I made the purchase.

I purchased a Maytag Legacy Series Quiet Series 300 in early July 2010. It had a recall for a heater part that could potentially burn down my house, so we couldnt use it while we waited for that part to be replaced. They offered me a small sum of money towards the purchase of a much more expensive dishwasher which I declined since Id only had the dishwasher a few months at the most. It is now the end of August 2011, a month past their factory warranty. The dishwasher did not get my dishes clean, made awful grinding noises and three days ago, it refused to drain and then spewed 50 or more gallons of water all over my kitchen which then leaked into the basement. The repairman charged $85 to tell me that the computer in the control panel had burned out and was not fixable. I think I paid somewhere in the region of $500 for this machine. My last dishwasher lasted about ten years. This is completely unacceptable. In searching the internet, I found hundreds, if not thousands of identical complaints. Clearly, this machine is a lemon and Maytag should be forced to replace it or better yet, refund the money spent to purchase the machine. Plus, pay for my valuable time spent mopping up water, washing dishes by hand, searching the internet for probable cause and potential solutions, waiting for Maytag/Home Depot to respond to my inquiries and a large sum for general annoyance. Maytag had a reputation of reliability (emphasis on had). Theyve got some slick ads but they do not stand behind their products at all. I will never by another Maytag product and I urge you to do the same.

I bought a Maytag stainless steel refrigerator w/ freezer on the bottom. Since 6 months fridge being in my house I started to have problems, rust on the doors, water coming out of the bottom, freezer door got stuck w/ ice and couldnt be opened, butter, eggs, milk can be frozen one day and the next they have mold and bacteria because of the changes in the cooling system, among my problems. And what? Well yes thank you so much for the guarantee Maytag has in Puerto Rico, IT SUCKS! They been in my house more than 5 times and nobody really says whats wrong. They supposedly change the computer, still having problems, and this was done after more than three times visits from Maytag guarantee. Im still paying for the damn fridge and DO NOT HAVE A RELIABLE REFRIGERATOR. Im wasting too much food, Im obligated to buy food almost every day cause Im scare to give something that may be bad and my family will be food poisoned. Whos going to pay me or my family if something happens. Maytag is still running falsely commercial ads and somebody MUST STOP THEM. This appliances are not free or cheap. PLEASE help us because Ive learned that Im not the only one having problems in Puerto Rico w/ Maytag. Also I believe Maytag is using technicians not ruled by the government of Puerto Rico and thats why the service is horrible.

I bought a Maytag MGR5605WW range on July 3, 2011 and it took till mid August before I received it. Right away I noticed when I put a pan on the grates, I had to be careful so they did not slip off. Dangerous! Then I made a pizza, and when I pulled the rack out of the oven, the rack tipped down and the pizza slid down on the oven. Danger again! I went over to Menards and they gave me the number of A&E (1-800-771-3029). I called them when I got home and an A&E person said they would call me back. After a few more calls, no one ever called me back. I went back to Menards. They said I need to deal with Maytag. I am very concerned with the racks, and so is everyone else. They are cheaply made. Tonight I had a family member place the frozen turkey on the rack and it bowed down! Danger again. The grates have a few chips. This is a nightmare. What a piece of trash. I’m trying to get someone to respond. This stove is dangerous to my well-being, and I have no other choice but to use it.

First Maytag washer we bought in 2003, worked flawlessly for 14 years, bought a new one in 2017 only because my wife wanted a bigger washer. Bought a Maytag top load MVWB765FW0. What a big mistake. In less than 3 years it has failed already. The water inlet valve went bad. Maytag offers no tech support because they want to charge you with a service call. I found out what was wrong by researching the problem and error code online and bought the part for $55.00 and fixed myself instead of them charging $100.00 just to show up at your door plus the part and labor. A washer failing in less than 3 years is totally unacceptable and I will never purchase another Maytag/Whirlpool product ever again. Someone needs to wake up at Maytag.

Purchased dryer less than 6 months ago and now have an issue with the powder coating bubbling up and flaking off on the dryer drum. Maytag says not covered under warranty unless found in less than 30 days. If I had know that I would not have purchased the dryer.

We bought a Maytag dryer and within two years the drum cracked. It will cost over $500 to repair it and then will the new drum be better? I bet not. Piece of junk.

Bought a Maytag Bravos washer 21/2 years ago... already have to buy a new washer... not a Maytag!! It started with the ul message coming on. Never could do anything to get it to go off.... then started leaking water around the bottom... bearings went out... costs more to fix than buying a new washer which is what I DID. Not a Maytag.... thought Maytags were a great product. Believe me their repairmen are always busy, not just sitting around like in their commercial.... Never buy a Maytag appliance again.

We bought a refrigerator June 4th 2014. 6 month ago the freezer and refrigerator was getting warm. Had to call repair service, it was the blower! On Saturday 12/9/17 freezer wasnt freezing, then fridge was clicking on and off. Unplugged it, called repair service, it was the compressor. $800.00 to fix it, the same amount as when we purchased it. Repair service told us to call Maytag, he said, Maybe they will help you, would not help at all. Talked to Lori, all she said was warranty is up after a year, I then said, I think a refrigerator should last longer than 3 years! Will never buy anything Maytag again! Yes Maytag does SUCK!!!

I have a Maytag Series 3000 washing machine which, as many knows, is the same as a Kenmore. I bought the set 23 months ago and since then, I have had nothing but trouble. In my first three months of ownership, I had my first error code of which I had to replace the hot/cold water valve. Fortunately, the unit was under warranty. Since then, I have had to replace the CCU and MCU twice. Now, the units MCU went out again! Whatever happened to the Maytag name? How can I get this permanently fixed or replaced? Is there a lemon law for appliances? Any assistance would be appreciated.

Bought this (Maytag Washer MVWB955FC1) on 1/8/18, was delivered late in January as it was on back-order. On 4/30/18, during a cycle, the washer made a pop sound. There was glass everywhere. The glass had shattered and exploded onto the floor and washer. The glass is on the inside of the drum and all over the clothes. Contacted Maytag and they sent out a repairman the next day. Repair said there is a point of impact indicated I dropped something on it. NOTHING was dropped on it. There is a point of impact, from the inside. The glass is pushed up and out indicating pressure from INSIDE the washer.Repairman says its not covered under warranty and that I had to pay for his time as well. He also said there are no known issues with this lid and washer. The lid is out of stock and wont be available for a while. I called Maytag and they gave me the same response, never heard of this.. and lid is out of stock. I found SEVERAL reviews/complaints in which, for the exact same model, this has happened to other people. This glass lid is dangerous and poses a serious safety risk to households that contain it. If they replace the lid, there is no guarantee this will not happen again. A child could walk by the washer and at any moment the glass lid could explode, send tiny shards of glass everywhere. I want a refund for this dangerous washer.

I purchase my first glass top stove; a Maytag. It came with a 10 year warranty on all elements and the glass top. As this is a first glass top I read through all instructions, there appeared no real warnings on what to do to maintain the glass; or rather what would damage or void a warranty. I simmered some maple syrup, and as it so often does when reaching the proper temperature, it boiled over. On a regular burner, one just uses a little elbow grease and your stove is returned its previous state. This actually pitted the glass, and as the warranty people at Maytag informed me voided the warranty, and seriously weakened the glass top suggesting it would be likely to break. Seriously?????? All of us boil stuff over on the stove top from time to time, and this damages the glass top and voids a warranty??? VERY DISAPPOINTED in Maytags product and their warranty.

The glass shelves stop 2 1/2 inches from the back of the refrigerator. Things keep falling down in back. I have a counter depth. Cant afford to lose any space. Freezer poorly designed for space compared to one I had before.

Both my washer and dryer are Maytag. Dryer element shorted out but was still under warranty so was fixed. Washer is very loud and now makes a rattling sound. Every so often it will hang in the middle of a cycle and the lid wont open until I unplug it.

Maytag Jetclean EQ Plus Dishwasher - We purchased the dishwasher in June of 2014. Recently the control panel decided it wont work. There is power to the unit. I am told that the unit is no longer in warranty so we have to pay for everything.

I have a new Centennial Maytag dryer. What a horrible sound it makes when the time is up!!! I had another Maytag dryer for 19 years and it did not sound as obnoxious as this new one. HELP!! I can tell some man invented it.

I bought a Maytag microwave model mmv4203ds00 on May 2010. On 8-20-10, the microwave stopped working. It was serviced under warranty. However, on 10-31-11, the microwave stopped working again.

My husband and I bought a set of Maytag appliance 12/2011 the washer squeaks real bad on spin cycle and now today the dryer started making real real bad squeak sounds to the point I can not use it!!! My appliances are only 4 years old!!! And we wash clothes once a week for just my husband and I. I would not recommend buying any Maytag appliances!!! They are supposed to be the best but are not worth **!!! And I called Maytag, they are not willing to help. Bad service!!!

I purchased the Maytag Washer & Dryer $1891.14 with Extended Warranties Model numbers: MHW5100DW0 & MED5100DWo. In September 2014 from salesman ** at ABC Warehouse for my Wife as a Wedding Gift. The dryer started malfunctioning toward the end of October, it was randomly flashing a red light indicating Check Lint Screen and when this happens the dryer will lock up not allowing you the OPERATOR to dry your clothing. We ALWAYS check our screen before use and clean after each use, so we found that light to be odd. But anyhow we checked the lint screen and nothing was on it nor was it bent out of shape, everything seemed normal to me & my wife besides the fact we spent $1891.14 on BRAND NEW washer & dryer set thats acting weird. I called ABC Warehouse spoke to **. He said Yeah they do that sometimes, you just gotta MAKE SURE YOU BLOW THOSE THINGS OUT MAN cause they dont like it dirty. I explained to him we keep it clean then he said the screen might be slightly bent. He went on to explain how he seen that happen a lot, I just said uh huh uh huh yeah yeah. So now its like the middle of November and the DRYER Check Lint Screen Light is coming on before every load now and staying on for long periods of time not allowing us to dry our clothing. So I called ** again 2nd week of December this time asking for a new unit. He told me to call the ABC Warehouse Store Warranty Department at 1-800-722-3333. I called and they gave me a number to Master Tech Appliance 1919 Federal Blvd, Ann Arbor, MI 48103 (734) 662-0641. I immediately asked why am I calling technicians instead of new unit when my unit is still under the 1yr factory warranty and in addition too, I have purchased an 5yr extended warranty? They wasnt trying to hear that. So I called Whirlpool 1-800-253-1301 told them the situation and asked for a new unit they said NO and then added by telling me their policies and how many times they can come and attempt to fix my unit before replacing it. I screamed and shouted at them explaining to them that I have spent $1891.14 on a non-working unit for my wife as a wedding gift and I am currently drying my clothes at the local Laundry Mat, they said NO still.So I called Master Tech, they couldnt come out until Feb 3, 2015. My wife took off from work. In the mean time it completely stopped working the first week of January, we had to go to the Laundry Mat every couple days cause we got 4 kids. SMH WOW my wife is pissed, I mean furious. When ** from Master Tech showed up he looked at our unit and said its also not getting hot so he called in to his job they told him to come back and order my parts and to schedule another day to come back. 2 weeks later Master Tech called with the appt. My wife took off from work again but this time they called the day of hours into the day to tell us the parts are on back order and they need to reschedule. My wife was VERY UPSET but we did it anyways. Now remind you are dryer is still out of commission. Were going to the LAUNDRY MAT. Master Tech came 3 days later (my wife took off from work) they literally took our dryer apart (Pics Below) for it to still not work, Master Tech called Whirlpool, Whirlpool told them to order us a NEW SWITCH BOARD. Wow what the hell are you serious? So Master Tech leaves again and orders the SWITCH BOARD. They came 5 days later (My wife took off from work) new switchboard and dryer still not working. Now throughout this whole ordeal Ive been in contact with all 3 companies begging for a new unit and nobody wanted to hear that especially WHIRLPOOL & ABC WAREHOUSE. With Whirlpool knowingly the switchboard didnt fix the issue the first time, they instructed Master Tech back to my home with the same but NEW SWITCHBOARD. LOL WOW I CANT BELIEVE THIS IS HAPPENING TO US. Master Tech schedules yet another day to come by 3-13-2015 & yes my wife took off from work AGAIN just to hear ** say sorry they keep sending me back with the same part and they know its not gonna work but anyhow Im here. He switched out the Switch Board again and still nothing. I called ABC Warehouse and they finally okayed us a new dryer with delivery day of next day, which is today 3-14-2015 and when it arrives THE WHOLE FRONT DOOR IS BENT OFF THE HINGE WOW WOW WOW WOW. Now they say our new will be delivered 3-17-2015 and yes my wife has to take off from work.Updated on April 9, 2015: 3/17/15 ABC Warehouse replaced the 1st broken dryer to only return with another broken dryer, same problem, red check screen light flashing & dryer wont spin. They left here.

I have had the Maytag Bravos washer since November 2010. This washer does not clean clothes. They are never even submerged in water. Had I known this, I would never have purchased it. The salesman at Sears surely didnt mention it. I remember being disappointed at the fact that there wasnt a washer in the place with an agitator. I am disgusted with the washer and the company. I realized that it has been over 12 months since we purchased it, but most people do not feel the need to investigate what is going on under the lid of their washer. I unfortunately assumed that the washer was going to wash! Silly me. No, it does a little spin spin and a little spritz of water (literally, thats it) and at the end, you are left with funk concentrated in the creases of your twisted up, stinky clothes. No agitator plus no water equals no clean! The smell is awful. Someone else described it best - a mildewy basement.Anyone else who is claiming that their clothes do not stink with this machine are surely being deceived by strong perfumes in their detergent and fabric softener. To get a true idea of what their clothes really smell like, they should wash a few times with a scoop of borax and no fabric softener. Then tell us how they smell. I am convinced that the entire line of HE washers is a sophisticated line of crap! They use such small amounts of detergent because that little bit of water going into it will not get any more soap out, much less sweat, dirt and lots of other nasty stuff. This may not be a big deal to other people, but it is huge to me. We have a small homestead. Our clothes get dirty. We spent several hundred dollars of hard earned money on a name we trusted and they do not care.Every load, every day, I am reminded of this fact and it infuriates me. Im not typically one to write in complaints, but as an American citizen where there is a free market (somewhat), I have an obligation. If a product is really good, the makers deserve my praise. Likewise, if the product is really bad, the makers (and refuses to compensate in any way) deserve my complaint, as do my hardworking fellow Americans shopping around for a new washer. Stay away from Maytag and if at all possible, stay away from HE machines. It is so true that they dont make them like they used to.PS: Maytag tried to blame this issue on government regulation when I called. Im sick of this passing the buck. I am fully aware of the chokehold government regulations have on business, but they only hurt small business. To act as if this is not a partnership between the government and big business (like Maytag) only adds insult to injury. Take a look at the money spent lobbying by this company. Disgusting. The good news is, any success they currently enjoy will not last.

Purchased my appliance at Lowes in 2012. I have had at least 8 service calls, the unit has NEVER worked as designed. Water leaks inside and out. The ice maker door heater had to be replaced. Fan Motors have gone out on it, broken water tubes. The temperature wont stay consistent, it freezes my refrigerator items, ruptures beverage bottles and cans. This once quiet unit is 3 times as loud than when I bought it. I am so frustrated!!!What a value $2,000 for the appliance, $700 out of pocket for repairs to date, $$ in lost food items, $$ in my time to clean the mildew, water, exploded beverages, cant put a $$ on the embarrassment when family/friends use. What is the potential danger to myself and family when the mildew is in the unit and water leaks into open refrigerator items? Next scheduled repair from my factory authorized repair technician? 10/29/2013.

Rust on two year old Maytag Bravos washing machine - I noticed some rust along the inside lip of the washing machine lid and along the seam near the top of the machine about a week ago. I contacted Sears where we had purchased an extended service agreement. However, the agreement does not cover rust. I contacted Maytag and there is nothing that they can do either. The machine is kept inside the house in the laundry area. We have had two washers in the past 21 years that my husband and I have lived at this house that were much less expensive than the Maytag Bravo. They did not rust. This will be the last Maytag product we will purchase.