Maytag BRAVOS XL Washer - The worst washer I have ever used. Do not buy! It does not use enough water and leaves a white scummy residue on dark clothes. You have to wash them all off in warm water and then send it through one or two more rinses to get it washed off. I may as well do laundry by hand! Absolutely disgusting!

Hello, I bought the above top load Maytag washer last summer and shortly after purchase the spin cycle was accompanied by a load grinding noise. This became progressively worse per use and I contacted Maytag Canada. The experience calling is a challenge with often busy, and at times long waits. When I did get through on the line they were very good customer-service-wise and arranged for a local accredited company to attend my home and assess the problem. Service visit number one resulted in the lack of parts to fix, so I waited two weeks for the next visit with appropriate parts. Washer began to grind again, I called Maytag, another appointment was set, service call #2 again resulted in the SAME parts being replaced as service #1, and upon departure the washer immediately resumed grinding. Call #3 to Maytag and a 4th visit was scheduled to my home. This time with a different service provider, parts changed washer not fixed. Maytag called and this time I asked for replacement. Three weeks later I received a new washer. The version was updated so the drain hose no longer reached my drain pipe. Once sorted out, my first wash today with the new unit and GGGRRRIIINNDDDING.. I would not recommend this product. Will be calling Maytag again Monday.

Bought the Maytag model MFI2670XEM and within 6 weeks freezer wasnt making ice. Repairman came and fixed it, within a couple weeks same problem again. It was fixed and within a couple months same problem. Fixed, but makes very little ice. Now 18 months later after purchase freezer is leaking water onto the floor. Very disappointed!!! After reading other Maytag reviews I am worried I will have to dump this relatively new refrigerator and buy another (wont be a Maytag) and our upgraded dishwasher from Maytag is terrible! I hand wash all my dishes before putting them into the dishwasher. The smallest bit of ketchup or sauce is not washed away in the wash cycle. Our Maytag stove/oven seems to not heat correctly, as well. Internal temperature gauge reads 5-15 degrees off all the time. Thumbs down Maytag! Extremely disappointed with Maytag products! Will never buy again!

I bought my Maytag refrigerator Sept. 2013 and now in December, 2014 it is dead. After five visits from Maytag to repair it, they say it will cost $1,200 to repair it. The advice the man gave me was throw it out and buy something different. The refrigerator never worked right from the beginning. Four of the visits were in the warranty period. Compressor and evaporator shot. NEVER AGAIN. Maytag does not stand behind what they sell.

Maytag Appliances - biggest rip off ever! Home Depot needs to stop carrying Maytag appliances. I purchased a Maytag washer Type 832-A, Model number MHWE200XW00, Serial number HL11990545 in May, 2011 from Home Depot. After just three years it flooded my laundry room. Home Depot couldnt help me, and Maytag Customer Service tried to really rip me off.I called Home Depot, asked why they continued to carry a product they knew had terrible complaints and all they could tell me was they are sorry I am unhappy with my washer, then gave me Maytags customer service number. I called Maytag - first the guy tried to sell me a $400 extended warranty package - total rip off. Maytag should be ashamed, then said he couldnt help because it was past the time period. There is no telling how many people they are ripping off with that little deal. Consumer Affairs should be all over this. So then he offered to get a Maytag repairman to come to my house, but couldnt tell me how much the diagnostic visit would cost or anything else. He was worthless.I hired a local repair person to come to my home, the part is $140, its the tub seal, weak and flimsy - has a giant hole. I only wash clothes and towels, nothing else. My local guy is cutting me a deal on the labor, still going to be $200. Maytag isnt what they used to be and I will never, ever purchase another product from them again, ever. And I would suggest you dont either. Maytag appliances only last a couple years at the most, and its customer service is horrid.

There should be a recall. Just look at the number of people complaining about this same exact occurrence about the control panel not activating. Im on my second control panel in 24 months. Some people are on their fourth already. Give me a break. There needs to be a recall and a redesign of this thing, which turned out to be a piece of junk washer.

Purchased this oven at Lowes on 2/8/2018 for $1925. Worked good until my wife cleaned the lower oven on 11/22/2019. The next morning the oven was locked and nothing would work. We called for service and the repair bill was $194.55. I told the repairman that the oven had a 10 year warranty on it, one year on everything and the rest on the parts only. He said no, and showed me in the warranty book that it only covered two parts. Which was not the two parts he had to replace. If you purchase a oven with self-clean feature, I would recommend that you do not use it.

We purchased a new Maytag dishwasher for $500 from Home Depot about 1 year ago... it stopped working 4 days ago. I did not get satisfaction from Maytag customer service as they tried to sell me a repair program whilst I was trying to determine if it was under warranty as it is a known problem. I now have a repair person coming out with a price of $189.95 + time. A complete joke of an organization. Lesson? Do NOT purchase any MAYTAG brand. They DO NOT stand by their product. My rating is ZERO STARS, the site forces me to enter a star which is ONE TOO MANY. I will NOT do business with Maytag, Whirpool or any of their brands again.

Maytag dishwasher mdb7749awm2 - It appears that everybody who bought one of these dishwashers has run into this issue at one time or another, and it usually takes one full year of use before the control panel goes out on these units, and in most cases, it has to do with moisture getting on the thin strip of wires leading from the control board to the control panel. It usually occurs right where the strip enters the control panel... There is nice little gap for moisture to rest right on the wires, which will eventually lead to corrosion. I included an image of what to look for (see the nice black rust areas on the wires? That was my problem, and probably yours, too). If you have some very, very fine sandpaper, and have patience, then you can get the rust off the wire, but be very, very careful, or you could take the small thin wire off in the process! Ive made this repair myself to my unit, and I did it for one my friends machines (it was a Maytag, and his lasted two years, but had the same problem, too), and both had similar problems and right in the same spot! After removing the corrosion, the system worked great again. However, before hooking the unit up again, I sealed the area with some silicone to hopefully prevent this from happening again. Now, Im not saying that this is the problem that you are having, but its worth investigating, and dont be afraid to pull-off the front panel...its just held on with an adhesive and will go back on with no issues. Anyway, this could save one hundreds of dollars in repair costs. I hope that this helps.

We bought a new home with all new Maytag appliances. Our Maytag dishwasher has had 3 new handles, 1 inside tub and now needs a new touch panel. Our Maytag oven/stove has needed three ignitors and the oven door has never been right! The microwave is the only appliance that we have not had a service call. Appliances are expensive along with parts and labor for service calls. I will not be purchasing any more Maytag appliances. The standard comment by repairman: They dont make them like they used to. How sad is that!!

I purchased a Maytag Centennial washer a few years ago. In my opinion it hasnt worked properly from the start. We went on the low end of price, because we spent a small fortune for GE products that broke after a year and a half. This Maytag hasnt been a much better experience. First it didnt drain and spin clothes, and I was told I was using too much soap. Cut back on the soap and it started working better and going through the full cycle but the clothes never felt or smelled fresh and clean. Now 2 1/2 years in, it doesnt complete the full cycle on its own, AND there is dirt in my washer after every load. My clothes come out with streaks of dirt on them. The picture below is of a pillow case I just took out of the wash! Ive cleaned the washer multiple times, but it doesnt drain properly so it doesnt help. Maytag charges a service fee just to come out and troubleshoot and charges you again to come and do the repair. Im running out of reputable companies these days with washers.

We purchased our Maytag® 4.5 cu.ft. White Front-Load Steam Washer online through Menards and picked up the washer on Feb. 5, 2022. We set it up on Feb. 6, 2022 and it didnt work properly from day one. The washer makes a clicking sound when it spins and also gets out of balance very easily. I contacted Maytag and they referred a warranty repairman in our area. He looked at the machine and said it could be one of two things and it would be a major repair. We would have to haul the washer to his shop and he would have to tear apart the washer to fix. He said it would be a big job to fix and we would be out of a washer for a few days.I also had contacted Menards shortly after we purchased the machine and they told us to contact Maytag. They wanted nothing to do with us and didnt want to stand behind a product that they had sold. Getting major warranty work done on a NEW washer makes no sense to me. I am very disappointed in Maytag and will never purchase anything Maytag again. Dont bother wasting your money like we did!

What happened to the days of buying a washer/dryer and having them for years! To spend a thousand on each and have holes in the bellow causing dirty water to Empty on your floor. Not once replaced, not twice, 5 times!!! Now Im looking to buy another. Old school for me...

After one year, this famous Neptune washing machine began to sound so noisy during the spin cycle that neighbors must have thought a 747 was taking off from our house. After researching the web, I found that the main bearing always fails in this machine and there is a new one-man repair industry started up across the US to just replace these bearings. In fact, someone invented a bearing puller just for this problem. I am deeply disappointed that a once fine company would knowingly put out such trash. I am replacing ours with another brand, even though we have used Maytag for 30 years. Customers always determine who wins and who loses in the long run. Bye, Maytag!

Weve had our Maytag dishwasher for less than 4 years when the control panel quit. The repairman came today. He was here 10 minutes and it cost us half as much as a new dishwasher. Its just the two of us and we use the dishwasher once every 4-5 days. Almost laughed when the repairman said the part and labor was under warranty for 90 days! There is no quality control anymore. Just greed.

My only issue is that I am short and find it difficult to reach the wet clothes to put them in the dryer. Other than that I am quite happy with the machine. I have had no problems to date. Thank you.

I purchased My Maytag Washer and Dryer set from Lowe's, which was a very good experience all the way, back in June 2017. After two years I can finally give an honest review. We love this set even though it is not as quiet as the old Maytag washers. Still is but not as. We have not had one bit of trouble from either the washer or dryer. The next size larger would have been the better choice for us since we now have king size bedspreads to wash. It still does the job though, just one piece at a time. A lot of people complain about the smaller amount of water used but it still cleans clothes quite well. If you need more water just use deep water wash or for even more water use the setting for bulky sheets which really fills up the water level.

Oven racks falling down and theres appears to be no solution because the interior liner of the oven has warped. The 3rd party repair guys tell me the interior liner needs to be replaced, its not worth the repair cost, Im better off shopping for a new set. Its so unfortunately that this happened (we moved into this house with existing appliances that we cannot use...) and it seems to be a common problem, yet Maytag claims they have NOT received any complaints about this.

We purchased a Maytag washer model MVWC400XWO almost 2 years ago and it has problems with the bearings and the whole computer board is defective. I was told to buy the extended warranty for $350, which we did. As of today, we were told by extended warranty they are refunding our money because there are so many things wrong with this washer, including the whole computer board, that it would cost them too much to fix or replace it. Im in complete shock. We paid well over $500 and are still making payments on it. I spent the day reading hundreds of reviews from people with these exact same problems and Maytag is aware of it and will not help. They should not be selling these anymore. Im completely sick to my stomach. I cant afford another washer and when I called Maytag, they said it was past the year and we are out of luck. I cant believe this can happen to people and they get away with it. A washer should last longer than 2 yrs.There are hundreds of people going through this with Maytag and no one will help.

No matter what we we do we still have soap residue left on clothes, even when we do the 2nd rinse cycle (what a waste of water). We use the correct amount of HE detergent and we use the detergent dispenser but it doesnt helps. The machine just doesnt use enough water. We have removed items that still have DRY SPOTS on them when the cycle is done. Areas that have never gotten wet after a 45 minute cycle. Never once had this happen with an agitator machine. Would not buy this machine again. Model: C80441070. Serial #: MVWX655DW1.

This product has cost us thousands of dollars in clothing!!!!!! We have a lot of pictures to prove this!!!! Greg Mackie Major Appliance does NOT back this product or US the consumer!!! We have bought THREE households of products from this distributor & they have NOT backed any of the products that they have sold us, or given us Any discount for repeat business or loyalty and have NOT Supported us in any way whatsoever!!!! We have spent thousands of dollars and have had NO compassion or support whatsoever!!!!!! We expect a full refund for this Failure of YOUR product & a NEW Machine that will CLEAN our clothing & NOT DESTROY it!!!!!! Very Disappointed in this Product!!!!!! We Will NOT purchase another product from Your Company or from this Distributor unless YOU make a conscience decision to make this situation Right!!!!! We Will Spread the Word about your Failure of a product & detour business from YOU & YOUR Distributor!!!!!! We have numerous other photos to share with consumers of how YOUR product has destroyed our clothing!!!!!

2 years ago I purchased a Maytag Washer & Gas Dryer. Unfortunately, I did not invest or believe in extended warranties. I believe in trying to buy quality products. The door on the washer would not open and 2 error codes were displayed. I was trying to add another piece of laundry and the washer had just started. I canceled the load, waited for the door lock light to go out, but the door would not open. The error codes began displaying E3 and F5. I immediately went to the Maytag website for a resolution. The suggestions did not work and was instructed to obtain service if they did not. I called for a service call for $35, but was told that the repair would be over $300 for parts and that was not including labor. The parts I needed were a control panel and a part for the door lock. This was not a Maytag Company service tech and he told me that this happens because the parts are plastic. Currently, besides a Maytag Washer & Dryer I have a microwave, stove, and dishwasher that are also Maytag. When I replace these appliances, I WILL NEVER BUY ANOTHER MAYTAG PRODUCT. I expect the quality and life of an appliance to be more than 2 years, without buying an extended warranty. When I told a friend what had happened with my Maytag Washer, she told me that she had a Maytag Washer broke down with a control panel problem, and she couldnt remember the other part. She informed me that her repair was over $500.

This machine(Bravos XL Washing Machine) was highly recommended to me at the Home Depot by a sales associate. I broke down and took the recommendation. Oh how I regret that! This is a terrible washing machine. It does not put enough water into the machine to even cover the clothes halfway. It ties the clothes in knots! I made a terrible mistake when I purchased this!

Read MANY complaints about these units leaking water onto the floor underneath. This is accompanied by a sheet of ice forming on the bottom of the freezer under the main drawer. Good money says the cause is a plugged drain tube. I had a Subzero that suffered a similar problem. The factory installed drain tube was a flexible coil type and food particles would be easily caught, compromising water flow - leading to an ice plug and eventual evaporator ice-over. I replaced the factory tube with 1/4-inch rubber fuel line and the problem went away for good. With the Maytag units, if memory serves, access to the drain tube is from the back of the unit. You have to remove an access panel to get to it. There is typically a small removable rubber restrictor cap on the bottom of the tube; this is the most likely spot for a clog to form. Due to its design, IMO, clogging and ice-over will probably be a periodic thing. If you are really handy, you can do this maintenance thing yourself.

We have a Maytag Dishwasher Model MDBTT60AWB purchased from Lowes about 8 or 9 years ago. This model was included in the huge 2010 recall of 1.7 million units due to the possibility of heater-unit fires. For the last couple of years, its had a problem staying on the selected cycle: After being started on normal wash, it reverted to rinse only after a few seconds, but eventually quit responded to the selection of other cycles altogether. Removing the back from the door to expose the innards revealed the ribbon cable that connects the circuit-board head to the control panel had worked loose. Reattaching it provides a temporary fix, but it eventually works loose again. We suppose the screw holding the back to the door will strip sooner or later, but by then well probably be so fed-up with fixing it that buying a new (non-Maytag) one wont seem like a bad option.

I have had this washer for a few years now and it is the WORST washing machine ever. I cant even wash a lightweight cotton blanket. It continually unlevels even with me rearranging the blanket over and over. Ill add some, take some out, whatever. It still wont work. The blanket fully wet is also HEAVY and with my arthritis, is very hard to pick up. I dont think enough water goes into the drum to actually clean the clothes either. The clothes at the end of the cycle come out in a weird mushroom form. And when the clothes do get through a complete cycle, they are twisted so tightly it is hard to get the wrinkles out in the dryer. Why would they sell a machine like this without having testing it more first? Dont get suckered into the Maytag name. Terrible washer!

On Thurs. Sept 25 at noon the alarms and lights started flashing on my refrigerator when I tried to get some water. I called Maytag, told them what was happening and told them to bring a motherboard when they came as nothing was working but the lights and alarms. I was told it was too close to the weekend so they would be out Mon. the 29th and I should just to get some dry ice. They came and the order said nothing about a motherboard, which is what the tech person who came also said it needed. Now they will be here on the 7th of Oct - maybe. 12 days is highly unsatisfactory for refrigerator repair. They had 4 days to see that the provider had a motherboard before the serviceman wasted a trip. Ive spent $102 on dry ice and now Im going to lose the food anyhow. I like the refrigerator but the service is really terrible so I wont be buying another Maytag appliance. The person at the call center ignored my diagnosis and it will be even worse now as over the weekend Maytag switched their call service to India!

I purchased a Maytag over the range microwave a couple of years ago when I had my kitchen remodeled. I have had it repaired twice already. Each time, it cost over $150. I bought this product with confidence that it was a quality product. To say the least, I am very disappointed and I will never buy this brand again. My previous microwave lasted over 15 years without a single problem. The only reason that I got rid of it was to have matching appliances. It was not a Maytag. I am looking to buy a new microwave and I will be sure to look at the reviews to prevent being suckered again!

I HATE this washer. It had such good reviews before I bought it, but I have never been so disappointed. Doesnt use NEARLY enough water to get anything clean, even when I try deep water wash, bedding, or power wash. You cant switch modes in the middle of a load, and if you leave it paused too long, it drains on you. Ive tried balling everything up as the manufacturer advised. I tried using less detergent, again as advised. Nothing works. Sometimes the clothes on top dont even get wet. Dont waste your money!! If I can find a way to fix my old washer, Im going to do that and throw this thing to the junk heap.

Bravo Series Washer and Dryer. I hate, hate, hate this washer and dryer. I have had it for 2 years and hate it more every day. What makes is worse is the over $2,000 spent to buy this piece of crap technology. The engineer should be fired and sham on Maytag for selling such a piece of crap. Washer does not get clothes clean and I have pictures to prove the amount of dirt and lint and soap left on clothes and bedding. Very poor design, and worse yet absolutely horrible engineering.To wash one item on delicate takes 47 minutes. No way around it and you are limited to the water temperature you want to use and the spin cycle that you want for that item. Water level is too low no matter what setting you use. I have read and reread and gone step by step according to instructions with no success of clothes coming out clean. Clothes are also twisted and knotted and wrinkled like no other machine I have used in over 50 years. The washer is very limited in what it allows you to do. Bedding cycle is a joke that does not work at all. One of the reasons I bought this was so that I would no longer have to take the time to drive to a laundromat. I washed a comforter and so much soap and lint and dirt was left on the comforter. I still had to take it to the laundromat to get it clean.Dryer is just as bad. Even with the energy saver off it still takes 1 hour and 20 minutes to dry 4 towels that are 5 years old. I cant imagine how long it would take to dry brand new fluffy towels. It was engineered to sense when ONE piece of clothing is dry. I want ALL my clothes dry, not one piece and the machine shut off. How stupid is that??? Engineers - design it so it senses when clothes are still damp and the machine keeps running!!! I can only use the time dry setting because no other setting even comes close to getting the clothes dry.To top off the hatred of this machine some damn engineer apparently thought this was a car and needed to be aerodynamic with a curved lid on both washer and dryer so you cannot put anything on top of the machine!!! Not every house is 5,000 square feet with plenty of room and storage!!! They want to force you to buy the drawers to put underneath and then the washer becomes too tall for short people to reach down into to get the clothes out. There is not one positive thing I can say about the washer and on top of it I will never purchase another item from the store I bought this set from. I have had service come out time and time again and they say it is an installation problem. Installation says it is service and yet no one will admit it is just a very poorly designed machine. Do not buy this brand or series of washer and dryers. This series deserves a minus and the company should replace every set sold!!!

In July 2012 I purchased a Maytag BTM standard door refrigerator from Home Depot. Approx. 2 weeks from the 1 yr. Standard warranty July 2013, my refrigerator started cycling like every 20 minutes and loud popping noises started occurring. 1st service tech would only stay 15 minutes & did not want to stick around to hear the noise. Ran the standard tests and said everything was fine. That was around Aug. 2013. So I put up with it for a few more months and finally the popping noise was getting louder. 2nd service guy (Jan. 24, 2014) got to hear my video recording of the refrigerator cycling and loud popping noise. He replaced a bad dul part (Note: they all wanted to blame it on our ice maker that we never ever hooked up). Oops...wrong diagnosis. Whatever he replaced stopped the constant cycling pattern but now the popping noise is getting even louder like a shotgun going off. 3rd repair guy (Feb. 20, 2014) tells us that is normal and recycle product material is not that good nowadays?? I pay a $1000.00 for a noisy refrigerator and they say it is a normal sound. I dont think so. The refrigerator is now popping so hard that the right side of my refrigerator that faces the open is now buckling due to the compression of the heating and cooling which is causing the loud popping noise. If you rub your hand down the side of refrigerator you can feel the waves forming on the side of the refrigerator. Trying to get a Maytag rep out here. Something needs to be done about the production of these bad appliances.

Purchased French Door MF12269VM 22 inch from The Brick furniture April 1, 2012. Turned out to be a real April fools joke. Purchased extended warranty with TransGlobal for 5 years. First, fridge delivered after about a couple of weeks because it actually wasnt in stock. Naughty Brick lied about availability. Fridge arrives and after a service call from Maytag repair, they ascertain compressor doesnt work.Order fridge number 2. Two weeks later, get second fridge but lever for dispensing water is broken off. Order fridge number 3. Usual two-week wait and fridge finally arrives but the whole side panel is damaged. Send it back and order Fridge number 4. Service from Brick, Maytag and Whirlpool, terrible customer relations. Misrepresented delivery dates, supply issues, and operational damages.Fridge finally installed. Ice maker operates intermittently for the next year. Service techs from TransGlobal offer a variety of suggestions including changing filter, water pressure issues. Finally ice maker stops entirely in Summer of 2013. Is replaced after a month of waiting for parts of which the wrong part was sent. Ice maker continued to operate intermittently. Sometimes just a small of ice or no ice for a day. Finally in May after another service call, ice maker stopped working for about 4 days. Tech comes out and miraculously, it starts working again. A month later stops again and hasnt worked since.Contacted TransGlobal off shore call centre? And arranged to have an assessment to see if we needed a new fridge. Request declined and Maytag (Whirlpool) sent a tech out after another week. Service tech recommended new freezer. Waited a week for parts and arranged for Service tech to replace ice maker. Wrong ice maker part (for the second time) in less than a year.The latest trick from our possessed fridge is recent alarms from the temperature control. To say we are disappointed in this product, the retail experience, the quality of the manufacturing, the shipping procedures, the poor engineering and design, doesnt come close to describing the shoddiness surrounding this appliance and the service weve received.In conclusion, we are still awaiting an ice maker and are contemplating buying another fridge. What it is fair to say, we will never ever buy another appliance with their the Whirlpool or Maytag attached to it. Nor will we ever again buy anything from the Brick, or depend upon TransGlobal for repair services. Are there other Manufacturers and retailers out there who understand the meaning of service and quality. I certainly hope so. Otherwise Im going to invest in a good icebox.

I purchased a Neptune washer/dryer front loader. All Neptune washers have basic design flaw over which the company should be sued. Since the bulk of the weight is in the front of the horizontal wash-drum, the entire assembly is suspended by a rear mounted bearing allowing the drum to spin. That bearing assembly is woefully under-designed and not able to support the unequally distributed weight that is inherent in any front load design.Since the forces of gravity cause a loading of the rear bearing on the front of the bearing raceway only, the machine is doomed to catastrophic failure of the entire drum system--and they all do this. When the washer goes into spin mode, it sounds like a jet engine taking off and that is a symptom of the bearing design beginning to fail which begins on the first use of the machine. The cost of the drum assembly/bearing and the labor is far more expensive than buying a new machine and therefore, not worth it. Avoid Maytag products at all costs.

We bought a Maytag dishwasher in May of last year. The control panel went out about 3 months after we got it. It just started doing its own thing Like not running the wash cycle or a different cycle than we pushed. We called for a repair and were told by the repair man that the control panel was on the fritz. He ordered a new one and told us it would be a month before he could come back and install it. When the control panel showed up at our house, we installed it ourselves because we did not want to have a faulty dishwasher running in the house.Just yesterday we noticed a huge rusty area on the bottom rack. We called and were hold for 20 minutes if not more, before we were even able to talk to a rep. She then came up with every excuse as to why our rack was rusty (hard water, water changing??). We asked for a new rack but she wanted to send a repair kit. We were on the phone with her for half an hour, if not more, and she just refused to send a new rack. When we finally asked to speak to the manager we were told the wait time was 32 minutes and hung up! Do not buy crappy Maytag appliances with even crappier customer service reps! (see our review about our Maytag fridge!).

I purchased the Maytag Bravos series washer and dryer recently. I love the dryer but the washer does not clean the clothes. I have to wash twice if I want it clean. It does not get the stains out and does not use enough water to rinse the clothes. It also does not use enough water to wash/clean the clothes. I ended up washing all the loads on bulky which fills the washer with water. It still doesnt agitate enough to get things clean. I am extremely disappointed in the Maytag product which I always thought was top of the line.

This washing machine is garbage! We paid almost 1000$ for it and it damaged most of our clothes. We believe this washer was released from Maytag with a functional problem. Because it does not drain the water and soap properly, therefore it leaves white stains on the clothes after it is done. Please see in the picture. After recommendation from Lowes we clean washed with Affresh for many times, it did not fix the issue! We called Maytag customer warranty service. They sent a technician and his solution did not solve our problem. We called them again and they said if they send a technician again they might charge us 130$. We think Maytag warranty is a waste of time and energy. They are useless. We will never ever buy anything from Maytag.

Purchased the Maytag Bravos washer approx. 2.5 years ago. I cannot even begin to describe how disgusted I am with this washer. My clothes i.e. towels come out ripped on the edges, clothes do not get clean, shirts etc come out wrinkled no matter what setting used. It is not energy efficient because loads of laundry need to be washed twice if they are soiled (like our everyday jeans). Went back to the independent store where I purchased washer and was told to use only the bulky or gentle/delicates cycles to reduce rips in clothing. Such a complete waste of money, and it was not cheap!

I bought my Maytag Bravos washer and dryer set about 3.5 years ago when I moved into my home. There was a 20-year old set here that did work, but I wanted something newer and more efficient, so I donated the old set and bought these. Performance of the washer has always seemed mediocre, clothes dont get as clean as I think they should, whites are dingy, despite using hard-water additives and the correct HE products.A few months ago, the washer started a new behavior: stopping during the initial fill cycle and displaying an F1 error. I soon figured out if I hit cancel then start again, it would resume filling and proceed with the cycle. Over time, I had to repeat it more and more. Its now up to ten F1 errors both at the beginning and end of the cycle. I dont have that kind of time to babysit my washer. I already have a full-time job.I have called Maytag/Whirlpool twice now, both times getting unsatisfactory answers. Even after escalating to the customer service supervisor, I was basically told that it is most likely the control board that is the problem and since Im no longer under warranty (that washer ‘is’ almost 4 years old, maam), Id either have to order the part myself from their supplier (total cost $250 + the risk of DIY), or buy their service package for about $350 which included fixing that problem plus one additional years warranty.I pointed out that for a major household appliance that I (over) paid for, I expect a life of more than 4 years, especially since I had a working 20-year old washer when I moved in here. Since when is this acceptable? I could understand if it were a wear-and-tear part, like a rubber seal or something that moved constantly and would eventually need replaced. But this is the electronics module, something that cant (or at least, shouldnt) be worn down or broken by use or even user error. This is an integral part of the machine, and if it has a fault (which it clearly does), the manufacturer needs to stand behind it and help the consumer.What angered me even further is that the customer service manager even admitted that models similar to mine had had similar problems, and a free control board was sent to those customers. But my model was not in that range of production, so clearly they have no fault, in their eyes. Apparently, its not even remotely possible that maybe when they determined the range of models they believed to be faulty, mine hadnt been in use long enough to display the same behavior? Maybe the range they selected is too restrictive and they missed some. From the volume of complaints Ive seen online, Id bet that to be the case.I asked to be transferred to their legal department, and was refused because we just dont transfer customers to the legal department. Well, I just dont buy Maytag or Whirlpool anymore, and Im going to do my best to make sure nobody else does either. Im replacing this ** with a different brand, one Ill be sure has tremendous reviews and a manufacturer that will stand behind it.

Please let me know if there is a class action suit. This refrigerator leaks water all my floor every three days or so. I have to chip the ice off the bottom of freezer every three or four days. Storage is also a joke. Poor design.

We purchased a Maytag MVWB765FW top load washer with agitator to replace a Whirlpool with premature gear case problems (less than 3 years old). Was partially sold by the attractive metal label that says 10 YEAR limited warranty. It is now less than 2 years old and the Maytag selected repairman just diagnosed a failing transmission and of course advised us this is not covered by the warranty. Cost to repair—$ 600. About as close to false advertising as I have seen.I can’t believe that this company would sell such crap and not stand behind their products! But after seeing all these other complaints I believe it now. I bought both washers from Nebraska Furniture Mart and I realize they only sell the appliances but I plan to inform them that if they continue to handle Whirlpool and Maytag products they will never sell another appliance to me or to anyone else I can influence to not buy from them. We as consumers are almost powerless against these manufacturers but if we can influence the stores we buy from, just maybe we will see some improvement.

I love using my microwave because everytime I am in a hurry, like going to work and my kids to school and dont have time to cook or we dont like to eat outside fast food I cook healthy the night before and microwave it the next day and it just feels like the food is just made. It taste so good my kids and husband love it.

We have a 2 year old Maytag washer and dryer. 10 year warranty may I add. Well, we get 2 frantic calls that say, “They heard an explosion and the bottom of the house is flooded.” An explosion so violent that it shook our 3 story house and sounded like a bomb went off. Our washer and dryer are on the main floor. When we get there we found the washer top was dented so bad that it dented the bottom of the dryer that sat on top of it - blew the dryer door open! Blew the front of the detergent compartment and blew the side apart! Scared my mother and father in law who lives downstairs and who is bound to a wheelchair! Not to mention the fact that it flooded the basement and ruined the ceiling and Maytag says they will replace the washer! Are you serious? Who wants another washer which may or may not explode! What about the damage to my house! This just happened a couple of hours ago! We are very ticked off and not happy with We will replace the washer! Bad, bad business. This is not where it ends! I want my house repaired and won’t settle for anything less! Shame on you Maytag for putting profit above quality! Consumers beware!

Maytag washer was bought May 2010 with an extended warranty, which expired May 2014. This machine was used by two people with average wash loads. Five months later the machine computer programming didnt work and the machine sounded like a jet taking off. Whirlpool said a one-year warranty would cost $329! This would have been less expensive than a new machine, but I felt I couldnt trust having it repaired. A repairman very familiar with Maytag products said he had three service calls the same day with similar complaints for the Bravos 300 series. He told me the bearings were bad and the cost to fix was not worth the money and this machine should have been recalled. I bought another brand and will not buy Maytag again. When my new machine was delivered, there was grease on the floor from the Maytag.

I purchased my Bravos washer and dryer in Sept. 2010. What a mistake! The dryer is okay but the washer is a nightmare! The repairman and I are on a first name basis. The last time he was here, he showed me how to recalibrate my washing machine. It stops working in the wash cycle, fills with water and then sits there. I have to manually drain it and start over. Then it gets confused and fills with water when it is supposed to be spinning and draining (consequently draining my well). I shouldnt have to recalibrate anything in life, much less, a brand new washing machine.

I have a bearing going out. The Bravo washer makes a terrible noise. Now, they tell me I need a new tub/bearing. This repair will cost me more than $250.00 plus service calls. This is the second repair that I have had on this machine. It is only 4 years old. I use it twice a week. I will not recommend Maytag to anyone and I will never buy another one. They should check the internet for complaints and realize that there is a problem.

Maytag Bravos XL MVWB980BGO. To start, I live on an acreage so some problems may be related to being on well water. The most annoying part is the washer doesn’t have a drain & spin without rinse. So, when my well pump started acting up, I had no way to just drain & spin off the load, so I had to try to lift thoroughly soaked clothes and try to dry them...which took about four hours. Another aspect that is a pain is uneven loads. It keeps trying to fill, instead of just stopping & letting me adjust the load myself. Then the damn thing won’t reset. I often have to resort to unplugging the machine and starting over. High efficiency is a joke. I’ve had the machine about five years now and it goes low flow error, even though the flow is fine. I’ve tried running cleaners through the water line and it’s still doing the same thing. The only thing left to try is take the machine out and try and manually go through the lines. For the amount of money we spent on this machine, I am thoroughly disgusted with how it runs. It is the first & last Maytag washer that I will ever buy. Next time, I’m buying as cheap & basic a machine as I can buy. On the upside, the dryer works perfectly.

I purchased a Maytag dishwasher model #MDB6769AWB2. After 1 year and 2 months of light use (just my wife and myself), the control panel went out on it! I called Maytag and because it was over 1 year old, they would not do anything about it! When you call their number listed in the owner’s manual, they thank you for calling their Customer Experience Center. This is an experience I can do without!

We purchased our Maytag Neptune Washer and Dryer approximately 5 years ago. Over the past year or so, Ive noticed an odor coming from our washer and it’s becoming stronger. Water is staying in the drum and there is mold growing on the rubber seal when you open the door.

Thankfully, Home Depot replaced the washer when Maytag wouldnt authorize a replacement after I had it for 3 days. Maytag wanted me to order a part, wait for the part, and then schedule their third party service contractor. It’s been about 2 weeks without a washer. Ive been posting about my experience and received an email from Maytag asking me to post feedback on their site, but it was rejected. Their note to me was “Our publication guidelines do not permit content that references a service policy, customer service interaction, or customer service question.” In other words, theyre not at all interested in customer service. Maytag/Whirlpool is no longer the brand to look for.

I recently purchased a Maytag centennial washer and dryer from my local Home Depot. I set up a delivery date of 2/9/12. I was contacted on 2/6/12 by a Maytag staff telling me that my washer and dryer were on back-order until 2/29/12. This is unacceptable to me. Why does your company not tell its retailers that some items may be back ordered? I would have accepted this if told when I scheduled my original delivery, but being told days later and after taking the day off from work, is poor customer service to me. I am giving very serious consideration to voiding this order and finding a new company to deal with. I do not have the confidence that future issues will be shared or dealt with in a timely manner.

Ive owned my Maytag Neptune front loader since 2003. Since then, the whites have either turned gray or yellow. Ive tried minimizing the use of Tide HE, maximizing its use, and I still get the same results. Can anyone please assist me with this major problem? Ive owned Maytag appliances since the mid 60s, and I know the quality isnt there anymore.

We received our new Maytag French door refrigerator today via delivery and got everything set up and magnets stick to the front. The last I checked magnets should not stick to stainless steel. So I called the Menards where we purchased the refrigerator almost 2 1/2 weeks ago and the store manager said there was metal liner under the stainless steel and states this on the technical specifications. And everywhere I went to look under the technical specifications NOWHERE does it state there is a metal liner underneath and even if there was the top is stainless steel regardless so why would magnets stick to it. I paid for a Maytag and basically got a cheap piece of crap Frigidaire or Whirlpool and paid extra for Maytag to stick a Maytag label on it. What a joke. If I have any other problems I will personally deliver this refrigerator to Maytag/whirlpool corporate and put it on the front step. I am VERY ANGRY!!

Does not clean properly! Water level is too low for clothes to move around properly. This appears to be a very poorly engineered product. We have had Maytag products for many years. The only good thing I can say about this product is that it beats a scrub board. Would not recommend Maytag product to anyone. Looking at other complaints it appears that Maytag is doing nothing about this. Will try to sell this at a yard sale and hope no one asks my opinion. Then go buy something that works.

I bought this Maytag refrigerator model MF 12269FRB00. It is not, user friendly, meaning that condiments and small bottles just dont fit conveniently in any space, The biggest issue is the ice maker. The ice maker shoots ice out on each and every attempt. Every time you want ice you are guaranteed to have ice shoot out of your glass on to the floor. I often challenge my guests to get ice without the cubes shooting out of the glass. No one has ever won. Dont buy this piece of crap, unless you find humor in having ice on your floor every time. Shout out to Grays Appliance in Melrose for selling crap! I will never buy from them or Maytag again. To the engineers who designed this product, you suck too!

I have a Maytag Clothes Washer. Lid Closed Light is flashing and agitator will not spin. Troubleshooting shows when the washer does not detect the lid is closed the agitator will not spin. I went to Maytag Canada website and chose Live Agent. There is no Live Agent! You get a Virtual Assistant that does not work; bad software. Virtual Agent shows connected. I type in the details of my issue and the Virtual Agent responds with No Input Detected. I type in the details again and the Virtual Assistant responds with Connection Closed, try refreshing. Over and over again. Tried calling the Maytag Canada 1-800 number. I have now been in the queue for more than 40 minutes. Just stupid cycling for a recording for common problems dealing with products that are not a washing machine (about a 9 minute cycle). NO CUSTOMER SERVICE. Avoid Maytag, Whirlpool and Kitchen-Aid products. Buy from another manufacturer that has live people working at the company.

Unbeknownst to us, our Maytag Refrigerators (MFD2561KES) ice maker developed a problem with the fill hose which connects to the back of the refrigerator, causing it to pop off. The hose had been leaking water onto our wood floor causing all of the boards under the refrigerator and 6 feet in front to buckle. I cannot see why Maytag did not use a compression fitting instead of using a squeeze type hose clamp. Plus the ice maker has left a large sheet inside the freezer on the bottom. I use the ice maker daily to fill my cooler for work.We also have a Maytag Dishwasher which has a push button panel in front which has decided to give out as well. Not to mention our Maytag Double Oven which has never been able to close properly since we have had it. (The service man said that there is nothing wrong with it). We bought our house 7 years ago and my wife wanted nothing but Maytag because of our experience in the past. I gave up buying american automobiles years ago and I guess the same will happen when I replace these appliances (after I finish paying for my new floor).

I purchased a Maytag refrigerator on April 4, 2012. This week, July 12, 2015, my compressor went out. I called repairman and he said the compressor was shot. I thought this refrigerator would last longer than 3 years. I had to go purchase a new refrigerator from Home Depot in Knoxville, TN at a cost of $1,057.95. I am 80 yrs. old, on Social Security and this was a lot for me to put out, since the Maytag should have lasted a lot longer than 3 yrs. I feel I am entitled to some reimbursement. The Maytag is a side by side, Model MSF25C2EXB00, Ser. HR21112159. Im disappointed in Maytag and will never recommend or buy another one.

I think that I finally figured out a way around the piece of junk Maytag sold me. I bought a Maytag french door, stainless, yada, yada refrigerator in 2006. When it broke down, see later description, the first several times it was ok because of the warranty. This POS has failed 7 times requiring $300+ to fix every time. When contacted about the issue, the people at Maytag seem happy. The business model is working perfectly. There goes another sucker. The refrigerator begins its eventual breakdown with the door alarm light and sound beeping constantly. Beeping that continues for days and weeks. The next progression to failure continues with it not beeping anymore but now the interior lights do not light when the refrigerator is opened. Finally, the refrigerator stops cooling entirely and it is dead.Now, Maytag no longer wants anything to do with it so you need to call a repair man. When the repair man arrives, the entire time he talks about what a piece of junk Maytag is. They, every time, at first think it is the switches and replace them. This NEVER fixes the issue. Next, they have to replace the computer brain. $400 to fix. EVERY TIME. Now, at least every year. If you buy Maytag and have a similar experience, get your wallet out. Sell you junk then dont stand behind it.

Purchased this Maytag dishwasher (Model DB7749SBM2) from a Sears 2014, no problems until now in late June 2014. The control panel is not responding. Start/Resume light is off, pressing it doesnt seem to do anything. Cancel light is off, pressing it does trigger the cancel drain process. Wash Cycle choices either dont respond, or for 2 of the choices engage an incorrect cycle. Option choices dont respond. Delay light comes on when an incorrect cycle choice displays but stays at 2 hours, cannot be toggled off or to a different delay length. Holding Control Lock or Delay for 3 seconds doesnt seem to clear the circuit board logic. Problem began with the Cycle choice buttons defaulting to Rinse Only. Control panel behaves not at all or incorrectly as described above. Seems to be a common Maytag control board/panel problem. We need help as we are unable to afford repair or another dishwasher. This time, it will not run at all. I called customer service today (August 11, 2015) and they expect me to pay for the repair. Repairman already said electronic board bad at a cost of around $300 just for the parts. It is easy to Google and find multiple review sites that indicate hundreds of consumers have similar problems, but Maytag will not acknowledge any issue. Based on the pattern the warranty is not going to help as it goes out just after a year. For only having it 1 1/2 years it is becoming very expensive. There should be a recall on this control panel.

I bought my Maytag stand alone dishwasher model # MDC4650AWB in August of 2009. I have used it once or twice a week since then. About 2.5 years ago the control panel crapped out. I forked over the $$$ to have the part replaced and installed. Now, 2 years later the panel is once again slowly dying. I just got off the phone with the Maytag people and they refuse fix it and take responsibility for the product failure. The machine has worked adequately for me aside from the control panel issues. The control panel was built to break. Shame on Maytag! Lets go forward with the class action lawsuit!!!

I will never buy anything made by Maytag again. I just bought this washer 9 months ago and the sensor broke. The repairman said I have to pay $300 for the new part and it will take 3 weeks, then the repair told me many people have this same issue and he wanted to be honest that this always happens to these washers and my best bet is to buy new... I am so sad I saved for 4 months to buy a new washer and it was a bad decision. I have learned my lesson.

We had a house built in 2007 and bought all new Maytag appliances - washer, dryer, oven/range, dishwasher, refrigerator and microwave. Consequently, we spent many thousands of $ and Maytag made much money from our purchases. In the 7.5 years since we have been using these appliances, the dishwasher already had to be replaced, as fixing it would have cost just as much as buying a new one. But its the range that I am so angry about. I have replaced the igniter 3 times since 2007, and last night, it went out again. I have spent $494 so far to keep replacing the igniter and once I make the service call to replace it AGAIN, it means I will have spent approx. $700 to keep fixing an appliance that is only 7.5 years old. Maytag says the warranty on the appliance is only for 1 year and will not budge on giving me a break on cost of parts and/or service. I will NEVER AGAIN purchase anything Maytag or recommend Maytag to anyone.

I bought a brand new top/bottom refrigerator from them. 1 1/2 yrs later, the cooling stopped and had 2 repair guys come out. They replaced it with BRAND NEW refrigerator. Now 1 1/2 yrs later, the same issue is happening. ALL my food I buy goes to waste. I bought NEW so this wouldnt happen. What happened to the old fridges from back in the day! Maytag has the WORST Customer Service!!!

No motor is available for the Bravos washer machine which is 5 years old! Now the machine is garbage and I need to buy a new one. I thought Maytag was a great brand so I purchased the Bravos but now I understand from the company that no motor replacements are available!! Wtf? Maytag/Whirlpool dont care for loyal supporters so, I am TELLING EVERYONE not to purchase Maytag/Whirlpool appliances whose name has gone for a dump with this latest situation.

We 19 years and gently used. The door latch broke. We purchased a used quiet series Maytag dishwasher and found that the door latch failed on this. I recently found over 600 complaints for the same problem. If you are receiving this many complaints and its one of your most frequent complaint, do you think its time for a redesign of the door latch mechanic is??? Or are you relying on your reputation and dont care about quality anymore?This is it for Maytag. Im glad we didnt buy a new Maytag because we would be stuck again with a crappy door latch. If you cant be bothered with fixing your door latch issues and you know that you have a long term problem here, you at least can send a new door handle kit to those of us who are complaining. Of course you wont do that. And the only recourse I have as a consumer is to tell others about the ongoing problem with your front door latch on my social media. Sadly, you are now only another crappy dishwasher with no real quality control. I bought several appliances from you because of your reputation for appliances that last. Seems that is now a myth.

I bought a Maytag washer and dryer, the Neptune series and thought I was getting a top of the line, but now the dryer has quit working and the repairman said it is not worth fixing and it is only about 5 years old. So that is what I am so angry about.

I purchased a small (14.5 cubic feet) refrigerator for my basement from Home Depot on January 26, 2013. It was delivered on January 30, 2013. On February 14, 2013, we found that it was not cooling like it was supposed to. The soft drinks in it were not cold. I called Home Depot and was told I had to call Maytag for a repairman to come out. Since it was so new, I felt it should be replaced. They disagree. The warranty only calls for repair. So a repairman came out on Feb. 19th. He said that it has no freon. He doesnt know why. It could have a leak. It could have leaked out in the warehouse. There is no way to know this. He said another repairman would be out to fix it on the 20th. On the 20th, no one showed up or called. I called the repair company, S & S Appliance of Bessemer. I was told the repairman that I needed is in Montgomery today and the repairman yesterday was told to tell me he would call me. He was told to not tell me someone would be out today. So now, I have to wait until tomorrow for someone else to call me and see when he can fit me in his schedule. I think Maytag has a problem with their refrigerators. I think Home Depot has a problem not standing behind what they sell. I think S & S has a problem with their servicemen. I am not happy with any of these companies and will never buy another Maytag refrigerator or washer, but thats another story.

It had always been my wish to own a Maytag washer and dryer as they were considered THE BEST! Well was I wrong!! I am on the third stainless steel drum, this one has a hole in it, need 4 wheels and pulleys, with service $542.61!!! On the average, I am having a service call every 6 months - last year we were gone for 6 months so no laundry was done, one drum was delivered and was egg-shaped. Maytag has been NO HELP! I am very disappointed with Maytag, their service and product. They HAD an excellent reputation, to me that is everything. Quality, customer service, and their word means nothing to me anymore.

We purchased our Maytag Bravo XL in 2012. Over the past year and a half we noticed the inside of the top lid is rusting as well as the bleach dispenser area. I called Maytag about the lid and they said there was nothing they can do and that we could buy a new lid replacement. Really??? My parents had only Maytag in their home for over 50 years with little to no repairs needed ever! We were a family of five back then. Because my parents always bought Maytag products so did we. This is the first time in 40 years that I have ever seen this happen! I was hoping for a recall for these issues but dont find any online. The washer and dryer were not cheap and purchased from a reputable retailer.

When I went to whip down the small shelve under the knobs, I cut my finger on the sharp metal. Was told that is the oven vent. Checked out your instruction book and found NO mention on that being a danger and to take care when cleaning. If I had been informed of that sharp metal piece I dont think I would have looked at your stove. The metal has razor sharp edges on both sides making it almost impossible to get too close to cleaning it. That shelf is a nice place to collect dust, grease and food boil overs and now I have to be extremely careful about cleaning. Thanks to someones not thinking in their designing. The stove is what I wanted other than that one fault.

Maytag Washer over 3 years old. Often problematic not functioning smoothly! Maytag invented this defective machine to intentionally rob the customer with all the probs that comes with it - poor design & quality, & not logistically programmed! Even aftercare/customer service SUCKS!!! Now, sensor spinning option is no longer working, drum not operational. No more Maytag!!!

I purchased a new washer and dryer from Lowes a few months ago. I had my former washer and dryer for nearly 20 years and although the dryer started to have some issues, the washer worked wonderfully. To have a matching set, I decided to purchase both a new washer and dryer. I was told the Maytag Bravos XL model was the top of the line and could handle large loads. After just a few washes I realized this machine does not add enough water to get the top clothes wet and there is no agitator to pull the clothes into the water. I returned to Lowes and was told to use the deep water wash. I tried that and still had clothes coming out from the wash still dry and dirty. Unfortunately Lowes would not take the machines back and I was told to call Maytag. Maytag said there was nothing they could do except send out a technician for a service fee of $98 to help me determine if the machine is functioning correctly. I could not dislike a washer and dryer more! The dryer catches clothes on one of the screws inside and pulls fabric pieces out. This is in my opinion the worst washer dryer set I could imagine having. I will share my experience with as many people as I can to help others avoid making the costly mistake of purchasing a Maytag product. Maytag does not seem to care they have designed and sold a dysfunctional product!

I purchased a matching set of Maytag Neptune washer and dryer about 6 years ago and the washer is junk! It sounds like a jet is landing in the laundry room. The repair man said it is not worth fixing - bad bearing. I am not happy!

Would give them 0 Stars if that was an option. Bought a Maytag washer and dryer in Aug 2021. Washer broke Jan 6 2022. Called Maytag/Whirlpool on Jan 6 as it was still under warranty. They only had one service company in our area to work on the washer. I called them and it took them 10 days to come see what is wrong. Ordered parts. Said it would be 2 weeks. We are now 6 weeks into this with no parts. Called customer service and they said they were notified that their service company needed a part and would take another 21 days to resolve. Talked to a supervisor (Demetrius) who sounded like he did NOT want to be in that position. Offered no solution other than we will just have to wait. Threw a 3 month extension for the warranty on which still does not fix the problem. Sad to see this company go down the tubes as it was once a pretty decent business with solid products. No longer.

My Maytag refrigerator Model MFX2571XEMS has to constantly be defrosted due to ice accumulation in the bottom of the freezer. If not defrosted, water leaks out onto our hardwood floor. Maytag will not do anything to resolve this problem. We were told by a repairman that we have to defrost it manually to fix the problem. Yeah at least every 2 weeks. What a rip off.

Purchase a top loader washer machine in Nov 2014, it is now Jan 2015. It is not completing drain cycle, leaving wet cloth. I am Not happy with the service. I had the tech people come out 3 time and saying to call customer service, and they keep sending out people. They do not want to give me back my money. Unhappy, waste of money, will not get another Maytag appliance again.

Just like all the other reviews, the control panel on our 3-year-old dishwasher stopped working. The obvious defect of the product and lack of customer support is unreal. We ended up replacing the Maytag with a Frigidaire. Hopefully it lasts more than three years.

I tried emailing Maytag but from what I read on consumer reports I doubt Ill get an email back. After our 20 plus year old Kenmore fridge was taken by hurricane Sandy I decided to try Maytag. What junk! We have a bottom freezer and were getting water build up on the bottom under the basket. In order to keep the water from leaking on floor I had to chop the ice out of the bottom every 2 days. My husband got frustrated and took the whole freezer apart only to find all the coils were covered in ice. Soon after that the ice maker stopped working. Tried different things to get it working. We finally took it apart and found the factory did not screw in all the screws on the inside so they fell out on the circuit board and shorted the thing out. Lucky it didnt burn the house down. All I can say is junk! Do not buy!

I bought a Maytag Bravos washer in March 2015. Over the summer I had two items, both cotton t-shirts come out of the washer badly stretched and torn. Other items have come out badly stretched, but not destroyed. After the second shirt was destroyed, I called Maytag (Sept. 2015). A young man was sent over. He ran the diagnostic, finding nothing wrong. He did not check the agitator. He reported back that it must be the way I loaded the machine. I use the Normal and Active Wear settings, leaving the center clear. My loads are very small. Under these conditions items should not get caught. Maytag stands by their claim that it is my fault. I only figured out what was actually happening when I saw an item caught.

I have the Maytag Bravos washer and dryer. The machine has broken several times every year, and every year, Maytag makes me feel like it is my fault. They built a machine, and they do not stand behind it. And I cannot get a local machinist to work on it. I have asked Maytag to replace it from the start, and they refused, telling me its out of warranty. The only thing out of warranty is the frame--all parts are new. Here is the history:On 1/04/2008, I purchased it from Home Depot, and it cost $815. Then in 4/2009, there was an F51 code, and Maytag replaced the mother board after long hold times and much pleading to help me. They said they could do nothing, because it was out of warranty. It took manager to manager to manager to get the agreement to extend the warranty. (I then found that this was a regular Maytag issue.)From 9/2010 to 10/2010, an ld code occurred. The approved Maytag scheduled service had to come out 4 different times to attempt to fix the issue. One time, they said it was broken wires for the drain pump. The next, it was off balance; and the next, it was a sensor. Then the next time, they replaced the mother board again, and again after much argument that the part was less than a year old. Each time, they get more and more difficult to deal with and made me feel more and more like I am asking them for something unreasonable. The service guys said the washer was like new.... All new parts and I would never have a problem again. It cost $80 after argument, and Maytag covered the parts.Last 2/2011, problems include a fast spin, ld code, and off balance; and it stopped working. It needed new suspension rods which cost $250. Maytag paid nothing. Then in 8/2011, ld code started again, and I would have to turn off to drain and then restart to spin. Maytag called in a service call, and they never showed up. Every time, they said they read over my file and that theres nothing they can do to help me. And no one else for me to speak to.In 10/2011, the ld code came on permanently. The Maytag call I made this time again said there was nothing they could do to help me.I am so frustrated; I dont know what to do next. I threw away an older set working washer and dryer, thinking I made a great decision to upgrade to this new set. Now my family of 5 cannot wash our clothes. No one will work on the washers locally, and Maytag treats me like Im complaining for nothing and I should just spend endless dollars to fix this machine. And Im at a loss. I had to get a part for the dryer the other day, and the parts store person told me that this washer is one of Maytags mistakes. if that is so, why wont they help me?

I have been using washing machines for 50 years. This is by far the worse piece of engineering I have ever used! On deep water wash, I would expect my clothes to be covered by water. I actually have to add by hand, four buckets of water and even then the clothes just float on top. The agitator NEVER pulls the clothes down to the bottom of the tub, they just move back and forth. The clothing that sits on top of the water, never gets totally submerged and is still on the top of the pile when the wash cycle is done. I will NEVER buy any MAYTAG product again. Lowes wont help me. I want to sell it, but in all good conscience, I cannot unload this on another person. I cant even feel good about donating it as it does not work...It is Junk!!!! Shame on Maytag for selling a scam. If there was any integrity in this company, someone would contact me and give me a better model.

My Maytag dishwasher will not come on and it is loaded. The control panel is out for the third time.

Purchased 4-2010, used maybe once a week, it stopped working 11-2013. They sent someone out to replace the faulty recall, which the recall says there is an electrical wiring failure that can cause a fire, so they replaced part. It did nothing, the dishwasher still would not wash, just fill up with water and drain, but would never go into wash, so we call and argue. First girl said that recall has been known to burn out the control panel so we have to pay for a service person to come out and diagnose it, if that is it, they will pay to repair it. Then when he does diagnose it, we call back, the next person says no, the recall has nothing to do with the control panel, that it is just a bracket that holds up the heating element... REALLY. Well then the Consumer Protection Agency has the wrong info because I just looked on there and the recall says, Electrical failure with the heating element that is not related to a bracket, I can read and I am not stupid, so we were out the $50 service call, so we finally got them to agree and pay for the part, but we would have to pay to put it on...HHHHHH NO, I am not spending another dime on service calls, I could spend the same amount and go and get a scratch and dent dishwasher for the same or just a little more. We are calling back tomorrow to argue more with them, then I am emailing the local TV station that handles these kind of issues. MAYTAG is a piece of nothing, I will never buy this or anything with their name on it again....

I bought this POS and paid almost 1000. Out the door with tax, hoses, delivery, etc. And it is by far the worst most useless pile of crap I have ever purchased. It just does not work!!! Its a washer that does not wash. It uses enough water to wash one sock and that still comes out stinky.. All my clothes no matter what cycle I use including deep fill power wash or if I add my own buckets full of water to the 1.5 hour wash cycle still come out dirty, stinky, stained and caked with detergent...Hey Maytag heres a hint. You need water to wash clothes and you need agitation to get out the soil, the dirt, the sweat, the stains, the stink and your washer does none of that. In fact I could get my clothes cleaner if I out them in the bath tub and swished them around with a broom stick for 3 mins. How could you go from the loneliest man on earth to the biggest scammer on earth by producing this boondoggle... P.S. Its only me and my wife. We are retired and our clothes are not even that dirty... Its just common sense. No water no action no clean. Ill never ever ever buy anything that says Maytag on it ever ever again and you can bet your life Im telling everyone I know this story.

I wish I had never bought a Maytag refrigerator! Nothing but problems. The ice maker does not work, water leaked 3 times onto our wood floor. Finally, I disconnected the control panel so I have an ice/water dispenser that is useless just like the refrigerator. I dont think the Maytag man is sitting around from lack of work, maybe laziness. Dont buy a Maytag.

Just like so many others, our Maytag 300 Quiet Series, just 2 years old, has a malfunctioning control panel. Repairman told us this has been an ongoing problem with Maytag dishwashers. Steam/water gets into the control panel.For a while it worked on and off and now it is dead. I am saving up to do the repair, but in the meantime the dishwasher sits idle.

I purchased a 2006 model Maytag Top load Washer and Dryer used 9 years ago January 2010 to replace a 2009 Samsung front load washer/dryer. I had to replace the agitator on Maytag washing machine before I could use it. Fast forward November 2018 the washing machine stopped agitating the clothes, but would spin the water out. I replaced 2 belts and thoroughly cleaned underneath and inside washer to remove soap residue. Maytag washing machine has been used twice a week since 2010-2019 and still going strong. Maytag dryer has never had any issues. I also own a set of 25+ year old Maytag Washer/Dryer both still working.

Purchased a Maytag MDB4949SHZ dishwasher new from Home Depot in January 2018 as part of an extensive home remodel and addition. Did not move back in permanently until late June 2019, so the unit was not used at all until then. It quit working in January 2021 and our local (Sandpoint, ID) appliance repairman diagnosed a bad motor and pump assembly (the main functional component of the dishwasher). The unit was marketed as having a 10 year warranty and based on past experience with older Maytag appliances we purchased it. The fine print reveals that the 10 year warranty applies only to components that are unlikely to ever wear out or fail; all the rest are covered by a one year warranty. Part cost is over $200 and does not include installation. Maytag customer service (45+ minute hold to speak to a live human) of no help. No way are we throwing good money after bad to fix it. Lesson learned; just purchased a Bosch.

I bought this washer brand new in 2011 for $650. I had bought a Maytag washer before in 1967 and it was still running in 1995 when I gave it away. Considering my first Maytag lasted me nearly 30 years (Last I heard the machine was still running in 2005), I never thought my new Maytag would give me any problems, until it was at least 10 years old. (I did know Maytag had been bought by Whirlpool but didnt expect any difference in quality). Boy, was I wrong! After using it for a month the machine broke down and it had to have the clutch and gear box replaced. Last week July 2016 the machine broke down again. It was the internal computer (referred to as the electric control unit) a printed circuit board that retails for approximately $300 (A ridiculous price given that much more complicated laptop and tablet computers today can be brought for $100, the circuit board should retail for no more than $40).With labor the repair bill came to $550, which was nearly as much as a new machine and did not justify the cost. Supposedly the electric control is susceptible to current surges and power outages. Given that this is the case, it makes no sense whatsoever that a machine billed as eco-friendly would carry a part that will doom it to the junk pile because of a power surge or outage and does not carry a surge protector. After learning of my experience Maytag called me the next day and offered to sell me a new Maytag at a discount price, which of course I flat-out refused.I would never ever again own a Maytag appliance or one made by its new owner (as of 2005) Whirlpool. With such susceptible electric units these appliances will sooner or later result in electric fires that will end the life of its owners. The US govt needs to protect US citizens from these predatory companies that make over-prized, throwaway products labeled as eco-friendly that are potentially dangerous. My advice for anyone that is thinking of buying a Whirlpool or Maytag washer dont do it. For those that already own these machines do not run them without a heavy duty surge protectors. It is not worth your life.

Maytag Range Precision Touch Control 800 Electric Smoothtop - The racks in the oven fall down. I have replaced them with new ones but am having the same problem. I emailed my concerns to Maytag a few months ago but didnt get any response (so perhaps I didnt go to the right site). The oven was purchased in early 2008 and this is the only problem I have had with it. If I am extremely careful, I can bake cookies but if I try baking or roasting anything heavy, the racks fall. It is very frustrating but I was pleased, for lack of a better word, to see that someone else was having the same problem - at least I know it isnt just me. I will try contacting Maytag again.

We purchased a Maytag 4000 series washer and dryer in October 2011, and within 5 months, the main bearing failed. The Maytag repair person told us it was an inherent issue and to make sure we use HE detergent (We always have.). Maytag advised parts were not available for 3 weeks, so no washer after 5 months of use. The bearing failed a second time after 11 months. Maytag refused to replace the washer and advised it was repairable condition. Now, we have the bearing fail a third time, and Maytag has advised that they would not repair the washer under the extended warranty program. They offered us 75% refund on the washer (So I guess they expect their products to only last 4 years.), which is simply unacceptable. We are now faced with purchasing a new washer, which will not match the dryer; or we have to purchase a washer and dryer of another brand. Maytag has provided pathetic customer support, and their response or lack thereof shows that they simply just dont care about their brand image or the customer.

Echoing the sentiments of others on this site, I am deeply disappointed in Maytag brand appliances manufactured by the Whirlpool Corp. When, for the first time in my life, I was able to buy all brand new kitchen appliances, I didnt even consider any other brand but Maytag. This was based on many decades of using Maytag products and watching my mother use them. I come from a big family so our appliances got used hard, and the Maytag brand ones worked year after year, decade after decade with little or no maintenance. To put it quite frankly, my new Maytag products are junk. I could supply a whole laundry list of problems but, in the interest of space, will just tell about the latest. A couple of weeks ago the fake tin foil paint on my oven and burner knobs just started falling off, revealing cheap plastic underneath. When I called Maytag to complain, I was asked how I clean the knobs. I told them that when I clean the stove front I remove the knobs and drop them in warm water with a couple drops of Dawn dishwashing liquid for the few minutes it takes to clean and polish the stove front, and that I had been using this same procedure for 2 years. The rep. hemmed and hawed awhile and then went away to consult her database. When she returned she told me that one is not allowed to soak the knobs per the manual, and therefore she could not offer any help. She then generously offered to transfer me to the parts department, where the rep. informed me that replacements would cost $70 EACH, thats a total of $350 plus shipping for 5 cheap plastic knobs. WOW! What a deal! I tell everyone I meet NOT to buy any Maytag branded product, and to apply extreme skepticism before considering any Whirlpool product. (BTW - the last certified Maytag appliance repairman to come & fix one of the appliances essentially admitted they are junk.) Model #: MGR8775AS SN: R32810432.

Dishwasher control board - This will be the 3rd time for this same failure with the start/resume button on control panel. Obviously, with all the complaints regarding this part indicates manufacturing is producing a defective or inferior part. The service provided by Maytag, which is supposed to be a reputable company, is a joke and non-existing. Like many others, here I will gladly be part of the class action suit and will never buy another Maytag appliance and will also inform others of their poor service.

Bought a MDB7601AWW, and then replaced front panel to stainless. Configuration options are great (can’t find better at cost up to $1,200.00)! I haven’t had an issue with any stains on non-stainless tub. Problem is now control panel failing for second time. After 1st time, sealed all connections in silicone to prevent steam from affecting it, as recommended on DIY video. I just replaced the door latch, thinking that may solve it, but hard to troubleshoot without any indicator lights. This second failure (2 yrs later) shows no indication that steam or water caused it. It does start now, stuck on heavy wash, heated dry, sanitize - per top lights. Front lights totally out. Debating whether to buy a new dishwasher ($$$) and give up super config (hard to find fold-down tines and fold-down small shelves on upper and lower racks, clips for small items, and basket that can be changed, placed anywhere) or spend at least $162 for the panel AGAIN and hope I get another 2 years from that while trusting that some other element doesn’t go out. I believe Maytag should, at minimum, make the panel reasonably priced by offering a rebate, since the part is not sold directly through them. Obviously this problem is a design flaw. I am the only one in the house, so the dishwasher is not under heavy use. At least I found how to replace it myself on YouTube, though it requires the door to be completely taken apart and would be easier with an extra set of hands and a younger back. Hard decision since it seems newer, expensive appliances have problems as well. If I buy new, I will not hesitate to get an extended warranty (1st time ever).

We spent $600 on a Maytag Jet Steam Plus dishwasher and its junk. We bought it in May of 2013 and the top panel is burnt out and the ribbon or control wires is corroded. Maytag wont pay for replacement parts and I wouldnt recommend anyone buy Maytag again. I thought it was supposedly a good brand but its nothing but garbage.

Before today I was happy with my washer. Well yesterday I heard this loud noise. It turns out to be the gear case on my washer. To my surprise the repairman told me that it would cost between $450 and $500 to replace. I called Maytag to check on the 10 years warranty and was told that it would cover the basket and the motor but not the gear case. That is very stupid because without the gear case the washer will not work. This gear case help the sensor work, the basket work. DO NOT BUY ANY A MAYTAG PRODUCT. They do not stand by their product. I have had my washer for 2 years and 10 months. Before this the last washer I purchase was a Lady Kenmore through Sears. I had that washer and dryer for 25 years.

This dishwasher constantly has an odor. I run the dishwasher every third day (there are only two of us), and no matter how well the dishes are rinsed off, there is an unpleasant smell whenever the door is opened. Even after running the washer, upon opening the door an unpleasant scent still lingers. I compare this washer to the Kenmore I left in my previous home and this brand new one falls short. I would not purchase this dishwasher again. But because this is only a year old, I guess I am stuck with it for a while.

Maytag wont fix new washer. Service person came 3X, but it still wont go to rinse cycle. Last 2X Maytag said service scheduled, but no one showed. MT mgr said cant help & to just keep calling back.

Purchased new Neptune stacks in 2002 and had several service calls on our expense and we noticed the hinges on the washer door were rusting! Ordered new ones from dealer but rust continues and has spread to top of machine over the bleach dispenser. The metal is falling off! Bad rust on the inside lip under door also. I contacted Maytag when I first noticed rust and they blew me off so I contacted the local dealer we bought from and they did nothing to help. Will never buy Maytag again and have not recommended it to anyone else either. ModelINGooZES. Serial: 51867064AJ.

I have a Maytag washer and dryer. The washer is a top loader with a metal drum. You can hardly hear the washer while it is running, and I have had no problems whatsoever in the past six years of ownership.