Maytag washing machine exploded sending glass shrapnel everywhere. At this point I believe Maytag should replace the machine. I appreciate after MANY hours on hold and being transferred that you are sending a repair person out, but there is tiny glass shrapnel all over inside. This is crazy, and a MAJOR safety concern.??? Update - can’t find parts or an eta. Replace the machine!

This Maytag Bravos HE machine has the poorest design! It doesnt use enough water on the normal cycle so I always have to use the bulky load just to get the clothes wet. The old washers used to spin the water out thus keeping the load even. This machine drains the water first and then tries to spin an uneven load! When this happens the machine bangs loudly from side to side, stops, refills with more water and starts the whole process again until it fixes its problem or until you go shake out the entire load and reposition everything. Then it uses more water to start the process all over again. It takes twice as long to do a load of laundry.Every time I use it I say I hate this machine! This machine should have never been released without extensive testing. Maytag could have figured out all of their own problems and fixed them so we wouldnt be writing all of these bad reviews. A recall should have been done years ago and the problems all fixed. I will never buy Maytag again!

I would never buy a Maytag dryer again. It has been serviced 3x since purchasing in 2010.

The Maytag Centennial is the worst washer ever. Not only doesnt get the clothes clean but it does not spin out properly either so your clothes have to be run through a 2nd time after washing. The water fill level is so low that the clothes are not covered in water at all, even midway through the wash.

This is the WORSE POS I have ever owned/used/etc.... our clothes are dirty, w/ a scummy film, really bad in most cases. Some have weird stain appear that werent there. Electric & water bills up. Have to always use deep water wash, double rinse. My clothes are wet when I put them in due to sensor fill (extra weight), also a zillion mesh bags. Clothes are getting trashed, faded so bad & smell bad. Having to use a cleansing product monthly, in one aspect, should encourage the engineers that signed off on this POS to change careers. Maytag customer service says no complaints have been filed!!! Horse **!!! $ 800.00, trashed, unclean, wrinkled to the point of almost needing to iron all your clothes. I have been going to the laundromat. Engineers should have been FORCED to use this machine at least 2 months.... good reviews my **.

I wanted a small stove that did what a large/standard stove could do. I was worried that the heat would be weak but it cooks my food amazingly well. This stove has all the bling of a simple stove for a smaller price and size for my tiny house.

I got a washer from a Menards Store in Fond du Lac, WI. I was given a line of crap at how great it was, and because Ive used Maytag for years I bought it. Id rather have my 20 plus old one back. At least it didnt take over an hour for a load, and the rinse cycle really worked. WE HATE YOUR NEW WASHER. As soon as we can afford a different washer well be looking for a different brand.

We purchased a Maytag electric convection oven with a warming drawer 3 months ago. We have been happy with the cooking features, but not the Aqualift self-cleaning. It does not work and Maytag does not acknowledge this. Instead they have offered cleaning products to us which their own instructions tell you not to use! Does this sound like a self-cleaning oven? They have offered to send out a service person to check the temperature. However, from reading multiple reviews by others, there will likely be no satisfaction from this company.

Rust on two year old Maytag Bravos washing machine - I noticed some rust along the inside lip of the washing machine lid and along the seam near the top of the machine about a week ago. I contacted Sears where we had purchased an extended service agreement. However, the agreement does not cover rust. I contacted Maytag and there is nothing that they can do either. The machine is kept inside the house in the laundry area. We have had two washers in the past 21 years that my husband and I have lived at this house that were much less expensive than the Maytag Bravo. They did not rust. This will be the last Maytag product we will purchase.

Bought this Bravo washer from a Sears Outlet Store. Had trouble the first 2 weeks and did all the troubleshooting to no avail. Just when I was ready to return it to the store I decided to try one more thing. The guys who hooked it up had reversed the water hoses - cold was hooked up to the hot intake, and hot water was hooked up to the cold intake. Took all of 5 minutes to switch the hoses to the correct intake and the machine works like a charm. MAKE SURE THE WATER IS HOOKED UP CORRECTLY.

I purchased a new Maytag fridge apx 8 months ago (model# MFF2258VEW6). It has french doors and a bottom freezer and from day 1 it has constantly leaked water all over my kitchen floor. I started putting towels in front of it after my first slip and fall. I had the water line checked for the ice maker and it was fine. It continued leaking day after day. Then I started getting a lot of ice build up all over the drawers and on my frozen food, which became freezer burned and I only had the temp at 2. They have a warranty on it, so called the company and they brought me a loaner fridge of the same kind.. OMG this fridge is doing the same exact thing, even worse. I am disabled and fell last night again and my leg and foot is so swollen.. I really hurt myself and Im not going to let this company get away with this!! I called the company and told them and they are checking into what they can do with the refrigerator. After reading all the about the Maytag bottom fridge leaks and other problems, I refuse to get the same one again. If they do not do something, I promise I will before I get hurt again!

Purchased this Maytag dishwasher from a local Home Depot in Feb. 2014, no problems until now in late July 2015 (about 18 months). The control panel is not responding. Start/Resume light is off, pressing it doesnt seem to do anything. Cancel light is off, pressing it does trigger the cancel drain process. Wash Cycle choices either dont respond, or for 2 of the choices engage an incorrect cycle. Option choices dont respond.Delay light comes on when an incorrect cycle choice displays but stays at 2 hours, can not be toggled off or to a different delay length. Holding Control Lock or Delay for 3 seconds doesnt seem to clear the circuit board logic. Problem began with the Cycle choice buttons defaulting to Rinse Only about three days ago. I assumed user error so let that cycle run, then was able to choose a different cycle (cant remember which one) which also completed. But since then the control panel behaves not at all or incorrectly as described above. Seems to be a common Maytag control board/panel problem, so will probably replace (with something other than Maytag) rather than repair.

This was purchased 3/25/2010 with the Home Depot Service Contract thru 3/2015 . We have already had a service call in 2013. We were OK until January 2015. Now we join many other customers with the leaking defroster. We have taken all the steps of the other customers. We went and called for a service appointment. Weve spoken to Maytag Customer Service 800-253-1301. Ive asked if there was recall? NO! I asked if there was log made of my call, NO! Any work done had to with Maytag Authorized Repair Person. The Home Depot Contract use a Non-Authorized Service Person. Weve gone to Home Depot. We are in a catch 22! We have spent good money on this refrigerator. Out of sight, out of mind. We will go back to Home Depot Again!

Bought our washer dryer set from Sears in the fall of 2010. I had reservations from the start as the machines were new and the salesman was really pushing this set (on sale), with all the customers, even offering extra discounts on these models only, if customers bought that day. Apparently, they had overstock and were trying to sell them all ASAP. That was a warning to me but my husband convinced me that I was being overly suspicious. We had previously owned Maytag machines for 20 years and loved them. So I agreed. Well, I have been cursing that decision ever since. You have to hand wash/prescrub any stain on clothing, even a little make-up like blush or a little mud. Then you have to put up with an inflexible system that wont allow you manual options regarding spins and temperature or times, etc. Its all programmed. Then you put up with clanging spin cycle as it bangs against the wall. Then you pull out very wrinkled and not always cleaned clothes only to begin the most frustrating dryer experience ever. It has a mind of its own. It can actually keep spinning as it keeps adding dry time and the clothes never dry! God help you if you have a regular load. All your clothes will get stuck on the little ledge. They stay there in a heap as the machine spins and spins.The solution? You have to add a bunch of dry towels to create a lot of mass so that it keeps your laundry from getting stuck on the side. Then you have to repeat this several times cause it doesnt dry well. I will never ever shop at Sears and I will never buy Whirlpool or Maytag again. I am now saving to buy another set.

We purchased our Maytag 4000 series electric dryer in October 2011 from Best Buy. We did get a very good deal and have had little problems until this am. I moved laundry into the dryer and started it. While I was loading the washer, suddenly I heard a popping sound from the dryer and smelled smoke. Scared me looking into it. Sounds like either our electrical cord or our heating element blew. Coming from an era (born in the 1970s) where appliances should last at least 20 years, I am disappointed with Maytag. I shouldnt have problems at least until this thing is 10 years old. And even then I have higher expectations. So when I replace this, it will be with a better product.

This unit is only 4 months old. It freezes everything, vegetables, eggs, etc. It took more than 3 weeks for the technician to show up at my door!! Performed a service modification according to the manufacturer specs. This did not work!! Call again to have a it fix. He show up almost 2 weeks later. This time he replaced a part, worked fine for almost 2 weeks. Now I am having the same problem. I had it with this Maytag piece of junk!! I will never buy anything from Maytag again!! PLEASE DONT WASTE YOUR HARD EARNED MONEY... IN MAYTAG PRODUCTS!

This washer is the WORST washer we have ever owned. I should have returned it when I attempted and Lowes talked me into keeping, stating I was just overfilling. I put only a few items and the jeans came out with dirt still all over them!! I have photos. Pathetic. Not enough water, not enough agitation. DO NOT waste your money!

Just passed warranty period and Maytag dishwasher broke. It would not start. Called and was allowed to purchase extended warranty for $135.00. A new panel was shipped and dishwasher lasted just under one more year with same issue. Another extended warranty was offered for $199.00. Needless to say we are buying a new dishwasher and not a Maytag or Whirlpool. The panels are notorious for rusting out. Hmmm moisture of a dishwasher and parts easily corrode.

Maytag Bravo XL -Model MVWB88OBWO. Washer quit after 13 months of light use. Repairman came, $148.00, worked on just a few setting for 4 loads. It has a bad controller and some other part. Total cost of repair, if I was stupid enough to make it, $650.00. Guess whats going to the trash. I guess that kind of negates the ECO-FRIENDLY, huh? I will NEVER own another Maytag appliance.

Purchased my appliance at Lowes in 2012. I have had at least 8 service calls, the unit has NEVER worked as designed. Water leaks inside and out. The ice maker door heater had to be replaced. Fan Motors have gone out on it, broken water tubes. The temperature wont stay consistent, it freezes my refrigerator items, ruptures beverage bottles and cans. This once quiet unit is 3 times as loud than when I bought it. I am so frustrated!!!What a value $2,000 for the appliance, $700 out of pocket for repairs to date, $$ in lost food items, $$ in my time to clean the mildew, water, exploded beverages, cant put a $$ on the embarrassment when family/friends use. What is the potential danger to myself and family when the mildew is in the unit and water leaks into open refrigerator items? Next scheduled repair from my factory authorized repair technician? 10/29/2013.

Maytag Bravos Automatic Washer 300 - I purchased this washer on July 29, 2010 from HH Gregg. It is less than 3 years old. The washer stopped mid-cycle, did not drain, and displayed the code Ld. The service company recommended by Maytag said that the control panel is defective, and the cost to repair/replace it is over $550 and isnt worth fixing since, he says, these washers are notorious for having problems. Maytag is unwilling to recall this washer despite all of the problems that have been reported. They are unwilling to even admit there is a problem.

I have a Maytag Clothes Washer. Lid Closed Light is flashing and agitator will not spin. Troubleshooting shows when the washer does not detect the lid is closed the agitator will not spin. I went to Maytag Canada website and chose Live Agent. There is no Live Agent! You get a Virtual Assistant that does not work; bad software. Virtual Agent shows connected. I type in the details of my issue and the Virtual Agent responds with No Input Detected. I type in the details again and the Virtual Assistant responds with Connection Closed, try refreshing. Over and over again. Tried calling the Maytag Canada 1-800 number. I have now been in the queue for more than 40 minutes. Just stupid cycling for a recording for common problems dealing with products that are not a washing machine (about a 9 minute cycle). NO CUSTOMER SERVICE. Avoid Maytag, Whirlpool and Kitchen-Aid products. Buy from another manufacturer that has live people working at the company.

Im extremely disappointed in this machine. I bought this machine after having my Kitchen Aid for 12 yrs. Just last month, the UL message came on. Had someone looked at it and noticed the bearing was loose. He fixed it, just today, it started doing the same thing again!!!!! Now it might be a suspension problem. Of course my warranty expired because I bought it in November 2012. Im never ever going to buy a Maytag washer again!!! Can someone help me to take my complaint to higher up?Thank you..

This is not about a Bravo but Maytag is the biggest piece of junk Ive ever owned. Have not had the washer but a couple of years and is leaking somewhere inside of the machine. Have to turn the water on and off just to wash clothes and still laundry room floor soaked. The dryer I have to run for 70 mins. on high heat at least twice to dry clothes, 3 times for your towels. Of course it lasted long enough so the warranty had run out. Never ever again would I buy this crap.

I purchased my Maytag washing machine in June 2011 and within the first couple of uses, noticed that my clothes did not appear clean. I went back to Home Depot and complained and was told I had to use HE laundry detergent and I was. I gave it a while longer and still, nothing I washed ever seemed to come out clean. Sometimes, the fabric softener dispenser fills with water; other times the fabric softener remains in the dispenser. The machine makes very loud clunking noises during the wash cycle. I knew this machine was a lemon from the get-go. I should have insisted that Home Depot come take it away. I will never buy a Maytag appliance again! Maytag should have recalled this washer long ago and, if there was a Class Action law suit, I would surely join in!

Bravos XL washer - I agree with others, if I won the lottery, this would be on the street in two minutes. It is a complete waste of money. Nothing comes clean. Supposed to be water efficient, well not when you have to wash everything multiple times and I have to do them in such small loads to have any hope of anything getting clean. Some clothes just never look clean. I have the same issue with all my dark things coming out with white residue and yet I use liquid detergent. I follow all the instructions and do the monthly Affresh tablet (cash grab) and still nothing is ever clean. I am SO disappointed in this machine. I thought Maytag and Whirlpool were good brands but not anymore. I also get a constant HC error and there is nothing wrong with my water lines. Just so disappointing, save your money and frustration and buy something else!!

We purchased our Maytag Bravos XL last month and within two weeks, we were noticing a BAD odor every time we used the machine. In fact, I just walked back into our house from outside and the entire house smells like old dirty dishwater and the smell is coming from the laundry room! This is a very expensive washing machine and we bought it because we thought that a Maytag would be better than the Whirlpool that just died after many years of repairs and aggravation. After reading these reviews, I wish I had bought a Speed Queen.

First the dishwasher - Control board no longer works. Seen many people with same problem. Dishwasher sitting there useless since cant afford to replace. Will cost as much as the purchase. Stove has defect between glass on oven door. Aqua clean feature is a farce and I feel vent at bottom of oven is asking for a disaster if any grease should spill in there. Maytag will not honor or admit any defects.

My Maytag dishwasher is 1.5 years old and wont start. The Maytag call center said they couldnt help me except to sell me a service warranty for $269. Then she wanted to argue with me when I asked her to pass on my dissatisfaction with their products to her supervisor. I thought Maytag was a good product. For what I pay for parts and labor, I can get a new dishwasher. She said do I expect not to have any problems with that dishwasher. I will never buy anything Maytag again. They do not stand behind their products. Plus, it sounds like many people have had the same problem with their Maytag dishwasher. This part is defective. (I am assuming it is a control panel problem.) Since corporations are people now is there someone I push into my dishwasher so they will fix it. LOL.

My 14 month old Refrigerator made a popping noise and quit working. I called Maytag and I had to pay $299.00 for a Service Plan so the repairs would be covered under a warranty and A&E Factory Service came out to do the repair. The repairman told me the Circuit Board and Compressor were melted and he was surprised it didnt cause a fire. The repairman had to get authorization to order the parts for this repair because they were so expensive and he is not even sure if the repair will fix the refrigerator. It is going to take 2 weeks for the parts to come in which means I will be without a refrigerator for a total of 3 weeks and were not sure if this will fix the problem. I am being told by Assurance (the warranty company) that they have to replace the parts 3 times before they will replace the refrigerator. I asked them, Exactly how long do you expect me to go without a refrigerator before I get mine fixed or replaced? When I called customer service and spoke to Brittany she gave me her standard robotic answers. I asked to speak to a manager and she sent me to the never-ending hold zone. I called back and non manager was available but they took my name and number and assured me that someone would call me back. I am still waiting for that call.

The washer does not clean clothes. Thank goodness I bought a 4-year warranty because they have been out 4 or 5 times on washer alone. The dryer is now squealing and shuts off (a safety feature I am sure). The repair person replaced the pulley system and one belt, it still squeals and shuts off. I called the Maytag CEOs office and talked to a machine. Some really nice lady called me back and said she cannot do anything to help me. They have no consumer person to help you and troubleshoot with you. The washer is rusting, it is an inside washer. I live in SE, Texas and they told me it was due to living close to the coast. Well, Ive had GEs that never rusted and in fact, the problem is really with all the HE washers. I hate them. They do not clean clothes. I will never buy another Maytag or Whirlpool product again.

We purchased a Maytag convection oven less than a year ago! Today is the 3rd time the heat sensor has gone on it! I want a new stove! I am beyond disappointed with the business and the product! Have always bought Maytag! Rethinking it now!!!

I purchased a Maytag front loading Epic z washer and I paid a great deal of money for it and now I have a broken part on it. We contacted the Maytag manufacturer and they have informed me that the part would not be available for up to two months maybe 6 months. I cannot afford to buy another washer, so now I have a broken washer and need to purchase another washer until the parts come in. I would not recommend this washer or dryer to anyone ever.

MDBH979SAM0 - Same old. Buttons not working. Control panel out. Repair cost total to be the same as the cost of the dishwasher. Its been over a year since we have extended warranty. Purchased from Home Depot. I am filing a complaint with the Consumer fraud unit of Washington State to get a State Action pursued on this.

Purchased our Maytag Centennial Washer Model MVWC400XW4 2 years and 5 months ago; guess we are luckier than most; it has now failed in the spin cycle, high pitch, high volume whine, sounds like it is about to explode. Needless to say is out of warranty; and too expensive on our limited income to have a technician repair. I will hope to make the repairs myself; nothing to lose at this point; and from reading the countless negative reviews about this product; should be as many countless repair suggestions on YouTube. Obviously if Maytag would stand behind/up for their product as they claim they do; I and many others would not have these issues. My wife and I for sure will never buy another Maytag product until Maytag resolves the issue, which if my calculations are correct will be never. My advice is simple, do not buy Maytag products.

Purchased this maytag oven from home depot November 2011. Oven has been working properly since install. The top burner controls do operate too easy and you can just brush up against the stove and turn the gas on which I seen here was mentioned. My major issue is the stainless steel finish that was applied. It appears that this metal was not properly prepared prior to applying the finish. The oven door is with rust blisters. The metal under the coating is causing this problem. The finish in the other areas is with no problems... No chemicals have been used to clean this oven.Customer service of maytag stated that this stove only has a one year warranty... so if you buy any maytag just remember one year and when it breaks down the cost to fix will be more than a new defective maytag stove. I will not purchase another maytag product and I do not recommend that this manufacturer be considered when purchasing any appliance.

At first you think wow Maytag. Have heard was the best washer. WRONG. Clothes come out dry in spots. Not washing like it should. Whoever came up with this water saver and no agitator was crazy. Clothes dont get washed properly. Give me an old school washer to where my clothes get clean. When you have to wash clothes twice makes your power bill soar through the roof. NOT GOOD MAYTAG. NOT GOOD AT ALL.

In 2011, we purchased this Maytag Centennial MVWC200XW1 washer. It will not complete the cycle when it goes into rinse and spin, will not empty water and once the cycle starts, it sounds like someone is inside with a hammer banging on the basket. Clothes come out with a powder residue on them and several pieces have had holes. Called Maytag and was told there was no service available in our area. I will never purchase another Maytag product. Used by two adults a couple of times a week, this machine should be trashed. I have to hand-wring our laundry as we cannot afford to replace at this point. My last washer was a GE and I had it for over 20 years, we replaced it because we moved into a new home thinking Maytag was the best out there. I checked for a recall because there are so many complaints on other sites but found none. We purchased from Home Depot and of course, they are no help.

My Maytag Bravos washer is 6 years old. I had to have the motor replaced about 2 years ago. Now, it gets stuck on uL on every spin cycle. I had a technician come, and was told its just cheaper to replace the machine at this point. What happened to the Maytag man of old, the one who never has any work to do because the machines are built so well?!

Very easy to use- just dial the button to the load of your choice! The only problem I have is it becomes unbalanced sometimes on a heavy load. :( And it is also energy efficient and lets you know when it needs cleaning.

I purchased my Maytag Bravos from Lowes in early 2014. A few weeks after the motherboard fried and Lowes replaced it with a new one. Within my 1 year warranty the new machine had another fried motherboard. Maytag replaced it for free. Now less than a year later the motherboard is fried again. Needless to say I just purchased another washing machine. Definitely not a Maytag. Now I just have to deal with a dysfunctional piece a junk for a few days until I get my new one. After reading all the complaints on here and other sites, Im very disappointed with Maytag. These machines are obviously lemons and any good company should recall them. Mine will be going straight to the junkyard. I have no interest in having a washer that breaks down every 10 months. Definitely the last thing I will ever purchase from Maytag.

I will never buy another Maytag product, and moreover, will tell everyone I possibly can, not to do so either. Like many others, I have a two-year-old dishwasher that needs a control board already, and from what Ive read this wont be the first time. It would cost $150 for the part, plus the service calls make it around a $350 experience. The only choice is to pull the machine out, or buy a 5-year warranty for another $318.56. Grand total for your marvelous high quality Maytag that lasts only 7 years? Around $1,000. I am so sad, the company used to symbolize quality but now when I see the logo, I think of landfills.

Bravos MCT maytag commercial technology washer - Bought this washer a year ago. Will not complete cycles. Will not agitate. Never buy Maytag.

Two in a row make it just over a year then the control panel goes out. You call a Maytag repairman and they say the control panel is bad! #1 it should last more than a year and a half. #2 a part shouldnt cost you as much as the darn dishwasher! Do not recommend nor would I ever buy another Maytag.

Maytag MHWE450 washer - Purchased this front load washer/Dryer and pedestals 12-1-2011. The bearings are so loud when it spins that you cant hear anything. You have to replace the whole tub to fix it with no directions anywhere on how to do it. I had a Maytag top load washer for 15 years before this. They worked perfectly when I sold them. I thought these would be a great purchase for a lot longer than 2 years.

I bought a Maytag washer and dryer 3 months ago. The Bravo XL is simply a piece of crap. No agitation and clothes come out as dirty as they went in. It also leaves soap stains on all the clothes by since it doesnt agitate enough. Nothing is wrong with the unit, just a horrible engineering piece of crap. Ive been in manufacturing for 30 years and cant even imagine how a company like this can design, test and still sell such a piece of crap. You put a shirt on the top of the load when starting and its still there at the end of all the cycles. Just absolutely horrible. Do NOT purchase any washer without the old time center agitator post. Horrible....

Our washing machine is 3 years old. About a year ago we started to see hairline cracks on the plastic lid in the bottom corners by the hinges. These have now become huge and pieces of plastic are breaking off every time we do a load of laundry. Maytag (under the Whirlpool brand) will not replace the lid for us. We paid $130 for a tech to come out and confirm what we already knew - that we need a new lid. And now the parts and labor will cost over $550. We have called customer service several times and spoken to a supervisor and the best they can offer us is to pay for the part which still leaves us to pay over $400 out of pocket to repair a $600 washing machine. This seems to be a common problem and is all over Google, yet Maytag is not willing to help their customers.

Maytag Bravos MVWB725BW - Purchased this washer last year and have been very unhappy with the way it washes. It is extremely harsh in the way the agitator moves the clothes. Because it has a low water level the clothes take quite a beating in the washing process. This is confirmed when I remove the clothes from the dryer and proceed to clean the lint filter. The filter is constantly full of lint, even after drying clothes that have been washed numerous times before. Additionally, the clothes, even though being put in evenly, end up bunching together.

It’s really quiet and it cleans the dishes, pots, glasses on just 1 cycle and I’ve had it loaded more than one time. I do use rinse aid and I do occasionally use dishwasher cleaner. I wouldn’t own angry other than a Maytag dishwasher. They last forever. The commercial about calling a Maytag service man is true! I’ve never had to call fior service! Well worth the money!

We purchased the Maytag Neptune washer and dryer on May 2005. We purchased it for $2,000. We have had so many problems as we have replaced the drain pump 2 times because of objects getting stuck in it. We have also replaced the door switch, as well as flooding my laundry room floor several times.In 2006, we received a notice of recall. We responded to the recall and were supplied with a GFCI plug for our washer, as this was to prevent the control board from catching on fire. In September 2011, the control panel on the Neptune washer failed. I now have to purchase a new washer, as this is an expensive fix. With this poor workmanship and problems that we have encountered, I am very disappointed. This was a lot of money to spend on a washer, only to last 6 years.

Purchased this dishwasher about 1 1/2 yrs ago. Luckily the first two times the control panel went out, it was still under warranty (within the first year). Now its gone out again! This is the third time! What happens is all the buttons will work except for the START and CANCEL. This has been the same issue every time. I tried restarting it, made sure there was not a leak that somehow was getting to the internal electrical components in the panel. I actually know the Maytag repairman by name. Its nothing like those old commercials where the Maytag repairman sits around and has all the time in the world because their products never break. Those days are over and these guys are busy working to fix these devices they label as dishwashers. Since my warranty is now expired, it was an unexpected $96 service call to tell me what I already knew - Its your panel again sir, it needs to be replaced. Well have to order one for you and itll be $265 for parts and labor plus the $96 service call = $361 repair for something that will likely break again in a few months. Never am I buying a Maytag product again.

We just replaced our 20-year-old washer and dryer for a new Maytag Bravos set. The Home Depot staff convinced us that top loading units were of good quality and reliable. We were fairly satisfied with our expensive purchase when our washer stopped spinning. We are just past our 1-year warranty of course so we called the service department. A young man in a beat-up pickup truck showed up and spent his time reading the manual that was hidden under the washer. His best guess was a $300 part plus a $100 fee for him to show up. So to repair a less than 2-year-old machine is $400. Im tempted to buy a different washer. It wont be a Maytag, unless you can convince me otherwise. I give you credit for great advertising! I was convinced that Maytag was a good name with limited repairs.

Pleased with all the features. I have had zero problems with this Maytag refrigerator; no problems with the ice maker; the crisper works well. The adjustable shelves are so convenient.

In April 2010, I replaced my washing machine (still functioning after 12 yrs) to upgrade to what I believed to be the top of the line Maytag Bravo 5.2 HE washing machine. Module # MVWB850WL0 type: 580-02. This machine of 3.5 yrs leaks underneath and after having the service tech come to look he advised me it will cost over $800 to fix (I paid over $900 for this unit). He says its the bearings and went on to ask me if Id been using the HE laundry soap (as if Im an idiot) and went on to ask whether Id been washing bedding. SERIOUSLY?!? !... After much research on this issue, I discover that there are similar complaints all over North America. Very disappointed and I want this lemon replaced by Maytag.

As all the other reviews day 1 Dryer had no heat, washer unbalanced and knotting all the clothes. Sent out new dryer after trying to fix to no avail. One month after new dryer, normal cycle continues to run and not turn off. Repairs again - new computer board. Now washer is winding high pitch noise level - repair new bearings. Thank goodness for warranty. But washer and dryer act up again. I purchased extended warranty. Washer tub needed replacing because transmission went out, dryer again control panel problems. Last night the dryer started on FIRE. I’m sure because the control panel normal was not working again after it was replaced less than 2 yrs ago. Total time owned 6 miserable years. Going back to basics, ugh....

Approximately one week ago, the display on my fridge began to flash and ice door flap continuously opens and closes. Upon researching the issue, it seems to be a very common issue and a known defect. One in which was apparently a recall at one point. I was told by a Maytag representative that the recall was from 2007 to 2009 and has since expired. Expired? Its a known defect and should be the responsibility of Maytag to provide the parts and labor to repair the fridge. I asked for a supervisor and was told that one would contact me within 24 hours. Well, about a week later, I never received that call so I called Maytag again. This time I was told by the maytag representative and a supervisor that there was no recall and that it was a Quality issue. A play with words, in my opinion. Anyhow, regardless of the title the issue was given, I was told I would be responsible for the repairs and costs. I attempted to look up the recall on Maytags website and had seen the last two letters of the serial number to my fridge listed under the recall, but when I tried to investigate further, the site referred me to the 800 phone number I had been calling. Now, had this been an issue that was not a known defect and apparently a recall, I wouldnt be writing on this site right now. But, because it is a known defect that maytag is aware of, I think its Maytags responsibility to pay for the parts and labor for my fridge.

It meets all of my needs and expectations. Its quiet looks nice and does a very good job of cleaning dishes.

If you have a second floor laundry room, DO NOT, and I repeat, DO NOT acquire this washing machine!!! The Bravo MCT model washer is TOO loud (during spinning cycle), and for some reason, the clothes come out all tangled up. Some cycles are a waste of a cycle, and most cycles take a bit longer than my former washer. I miss the cycle choices I used to have on my former GE Profile washer (GE does not make that model anymore hence my changing brands). For the most part, clothes come out clean; thats why I give it a two-star rating instead of one. The dryer: Must dry every load in low heat so it doesnt come out extra crispy and wrinkled up. Although I generally have to run a second drying cycle, low heat does work great and the clothes come out ready to be folded/put away.

Everything in my house is Maytag. I assumed they were the best. My dishwasher went out after three years, and I replaced it with a Maytag. Now, my over the range microwave is not working. I will not replace it with Maytag. I expect my washer and dryer to be next.

New Maytag double oven installed by contractor in my house 18 months ago. I have had a few problems with it. The problem I am having today, the panel says error detected, remove from power source. I have had this problem a couple of times. I also have had the problem where the panel will not recognize anything I put in. I have to pull stove out of the small slot it is in, unplug and then push back. Not easy. I was the one that told contractor which Maytag range I wanted because I felt it was a good product. Problems from day one. This double oven/with range cost a pretty penny and I really cant afford a new one.

Control Panel MDB8949SBB - I purchased my dishwasher in August of 2013. The control panel has stopped working and Maytag refuses to discuss the issue with us. Regardless of how many complaints they receive they are in denial about their product. They now offer a Repair +1 program which costs $260 for a repair and an additional 1 year warranty. If I do that I will get 1 year out of it before I run into the same problems. Any ideas?

My Neptune Maytag pair have been dependable. Great features. Now at 20 yrs old still kicking. Washer-front loader now has issue with fab softener going into wash correctly. Could be build up? Trying to self-fix. Very gentle with washing fine things. Hope I can keep going with them.

I will never buy another Maytag appliance. We built our home in 2005 and bought brand new Maytag kitchen appliances (refrigerator, gas oven/stovetop, dishwasher, and hood microwave). In seven years, we have had problem after problem with all four appliances. We had to replace the compressor in the refrigerator in the first 18 months and then the fan in the refrigerator about a year ago. We have had to replace the heating unit in the oven twice and the handle has broken off of the oven door twice. We have had to replace the handle latch on the dishwasher once and today, the microwave stopped working. We are not rough on our appliances (especially the microwave as we rarely use it), so I think the fact that every single Maytag appliance has broken down one to three times in different capacities in the last seven years says it all. We have had a very poor experience with this brand and will definitely never buy another Maytag appliance.

HORRIBLE. Dont pay more for substandard machines. Had a Maytag washer and dryer delivered on March 27th 2018 and it has been a nightmare to get it to start up. Now I have clothes stuck in there. I called Home Depot, you should never buy any appliances from them, they wash their hands of all responsibility once you sign for it. Called Maytag. On hold for almost 10 minutes, they only have 2 certified repairmen in the area 0f 600,000 people. Will be 5 days until they come to look at it. I told them I wanted to return it for a GE or something else. They said I had to contact Home Depot yet Home Depot told me it was Maytags problem. SAVE YOUR MONEY!!! MAYTAG IS NOW AN INFERIOR PRODUCT WITH EXTREMELY INFERIOR SERVICE.

The ice maker in my Maytag French door refrigerator quit working 11 months after purchase. It was replaced under warranty, but again quit working 12 months later. That one was replaced at my cost, and lasted another year. It was again replaced at my expense and that lasted two years. I am now back to the dark ages of filling ice cube trays. I have been reading reviews, and find I am not the only one who has had problems. My letter to customer service was responded with a sorry about your luck letter. I would never purchase another Maytag appliance.

I have a fairly new washer Maytag model #MHWE500VW serial #CSY0303991. I need Part # W10415587 doesnt excist for my washing machine anymore. Its been on backorder since Apr-May 2011. Maytag/GE insists that they are not responsible. As long as they can say backorder technically they are not liable for anything and dont really care that me the customer is having a problem and they Blatantly refuse to even investigate. I spoke with a GE supervisor just today and she basically told me wont help you because my appliance is out of warrenty. And she explained to my that my complaint will go into a file that no one will ever see. I searched the internet only to find hundred of other consumers are waiting for this same part. Ive called distributors & manufactuers. Same answer, backorder. My warrenty people are trying very hard to help me but again Maytag/GE refuse to help. Very dissappointed with this company. Wont be purchasing Maytag/GE products again. Wheres that guy in the commercial with nothing to do when you need him??

Theres always a problem with this thing. It doesnt clean the clothes, its always off balance, and now it leaks from the bottom side of the machine in the clean washer cycle. Its only 2 1/2 years old. Should of listened to the guy who fixed my old machine. Dont get a Maytag!

I bought this Maytag Dryer in May 23, 2015. I had nothing but problems. I had 4 techs come out and say different reasons why it does not work. I had the vent exhaust clean out. Still not working, the one tech said there was not enough clothes for the dryer to sense it wet. I did a huge load, still doesn’t work. The sensor for the vent keeps popping up and it’s cleaned. I have to pull it out and in to get the signal light out. Cant turn on the machine. It still does not work. I tried contacting Lowe’s, since I bought an additional services plan. They said I have to call every thirty days for three months. That means I have to take my time out of work and wait for a tech for three months to get make a complaint and TRY to get new one. I really disappointed with Maytag and Lowe’s. I have a tech coming out this Monday, 11/23/2015 for another services call. I will never buy at Lowe’s or Maytag again. How many times does a certified tech from Maytag have to come out check a brand new dryer?

My wife & I purchased our Maytag dishwasher model # MDBH979SAB1 on 3/8/13 from homedepot.com. Approximately 24.5 months later our dishwasher experienced control panel light button malfunctions similar in description to the many other consumer complaints on this & other forums. I would like to share some additional information based on my research about this issue and possible fix. The source of Whirlpools control panel issue is design related. The issue is caused from moisture which induces oxidation on the Flexible Printed Circuit (FPC) cable that is integrated with the control panel and connects via connector to the electronic control box. The issue usually manifests itself on the cable just where it bends coming out of the touch membrane panel.The oxidization of the FPC cable eventually creates electronic shorts or opens between the parallel traces thus causing the panel control lighted function problem which disables the dishwasher from being used. The cable, since integrated with the control panel, is not a separate replaceable part. In order to repair, the Whirlpool diagnostic action is to replace the entire control panel. I quickly learned after doing some online research about Whirlpools control panel issue that it extends back to at least 2011 with control panel part # W10475784 and corresponding or like PNs of this design. The number of control panels sold of this design by various online appliance part centers coincide with the high number of reported like control panel failures.In just 2015 alone so far, the sales for this control panel have been in the hundreds. This indicates that Whirlpool continues to replace defectively designed control panels upon failure with defectively designed control panels. There was also a class action lawsuit filed against Whirlpool in the state of California on May 6th, 2013 for the control panel issue. The filed lawsuit is public & the whole document is available online as a pdf file. Unfortunately, Judge **, granted Stipulation to Dismiss Case with prejudice 74 on 5/23/14. I was unable to find out any details as to why the case was dismissed. I did not call Whirlpool about my control panel issue, instead I handled all correspondence through Email to them at WHIRLPOOL_CUSTOMEREXPERIENCE@WHIRLPOOL. COM.My initial correspondence included all the facts about this issue & that I did not wish to have their warranty coverage/period explained to me for I understood them, the problem was a quality issue, and just basically wanted to know what they were going to do or have been doing about resolution. The email correspondence with them got me nowhere. They initially replied back with all the form niceties like We apologize, We understand your frustration, & We value you as a customer, but denied every knowing about such control panel issue, regurgitated their warranty policy & period and were unwilling to resolve anything. In their last reply they stated how unfortunate it was that customers only take the time to provide negative feedback!! This is just bad business, and though I would not like to think it, but the control panel issue may have been by marketing design.Please keep in mind that Whirlpool manufactures appliances under at least 15 different name brands including Maytag, Kenmore, Admiral Kirkland, KitchenAid, Roper, Speed Queen to name a few. All is not lost, being an electronics engineer I looked into the do it yourself fix. If you are not comfortable in doing this, you may be able to find someone to help. I was able to repair mine by carefully scraping off the oxidation from the FPC cable (will appear brown in color) & encapsulating it with high density 100% dampening silicon (non-caulk type) to protect it from moisture & withstand heat. There can be other ways of protecting it from moisture instead of silicon, just make sure it can withstand heat, wont become brittle, & that it may not cause potential damage to the cable itself.My repair has worked for about 4 weeks now, & shows no sign of oxidizing. The problem may be more severe if the oxidation has actually opened or broke one or more of the small cable traces. Do not attempt to solder this cable! Its way too thin & will only make matters worse. An open can be carefully bridged with a conductive glue or ink thats on the market. One source is a window defogger repair kit product thats sold at auto stores that has a conductive glue in it. Post open repairs will need to be checked with an ohm meter to make sure repair is good and that any adjacent trace lines have not been shorted by repair. Of those of you that have just bought or had installed Whirlpools defective control panel, please encapsulate the FPC cable as soon as possible to protect it from moisture. If you dont, it will surely oxidize again over time.

The Neptune Front Load Washing Machine I purchased in December of 2007 started sounding like a jet taking off, about three months ago. The noise has become unbearable. The repair person said that the whole drum needs to be replaced and it is not worth fixing. Are you kidding me? This was an expensive washing machine and now we have to get a new one? We cannot afford to get a new washing machine. We need an explanation of why this would happen and from the other complaints I have read on the Maytag website, we are not the only ones. This is the second time something has happened to this washer, the first time, it was under warranty (only a few months into the purchase and the pump was bad and was replaced). What is the company doing to help people with this faulty machine?

Maytag Bravos Quiet Series 300 - Our motherboard on the washer went out after 2 years from purchase - just out of warranty. Motherboard was $550 so we bought a Samsung. Now our dryer has gone out for the second time. First time was the pulley assembly came apart. We self-repaired after watching YouTube. Now the motherboard has gone out on the dryer! I will NEVER buy another Maytag product. They are a waste of hard-earned money and have left me with piles of laundry numerous times. Maytag, you need a class action suit filed against you!

We purchased a Bravo HE washer about a year ago after our old Maytag finally died after 17 years. Our new one is more quiet, does a good job with less water although the cycle times are a bit longer.

Preheat the oven, put in the food. Oven does not maintain the temperature. Gives me a code of F2-3. Want to know what part needs replaced to solve this problem. If anyone can relate to this problem or help me with information please respond to this or email me.

Machine (Washing machine front loader model # MHW 5500 FC1) purchased August 2017. From the start Service Dept USA told me to unplug and re-plug anytime I had a problem as this problem started right away right after installation. In January it was getting stuck on the spin cycle. Unplug and re-plug to no avail. MAYTAG DO NOT have their own technicians just so you know. In the my area they use two subcontractors. In January they sent out the first sub-contractor from Appliance Wizards. He is a one man operation I later found out. As soon as he saw that I had a stacked washer and dryer he told me that this was my problem. He pushed a bunch of buttons on the machine, obviously re-setting the motherboard in a different way than unplug and re-plug and told me that there was nothing wrong with my machine. Not true. Machine was getting stuck again. Called Whirlpool service USA again. Told them not to send the same company. This time they sent JC Service. Excellent company. Kyle came out, identified that it was the motherboard. He claimed that they had other consumers with the same problem but that MAYTAG has corrected the problem and he went ahead and ordered a new motherboard. Waited 8 days and Kyle and another serviceman came and installed the new motherboard two days ago. Yesterday I put in my first load and the whole machine went dead. Kyle came again. He claims it is the motherboard again and he ordered a new one. I called Whirlpool service USA and spoke to Tina. All I wanted them to do is to ship my now, third motherboard quickly by courier so that I would not have to wait another 8 days without a washer. Her resolution was to extend my warranty by 6 months. I advised her that I had purchased a 4 year warranty but if they did not fix it so I can use it, even a ten year warranty would be of no use. So then she went and started reciting THEIR RULE OF LAW with regards to their protocol and told me that if needed they will replace my motherboard as many times as needed. She would not address sending the motherboard quickly. I asked for a supervisor several times and finally she agreed to put me through to the supervisor. She was worst than Tina. She agreed to check with the parts department and if possible she would ship it out by courier. I asked her to keep me on hold while she checked. She came back saying that they were not answering and that IN FACT they could not ship it out expeditiously. So, IN OTHER WORDS, SHE WAS LYING TO ME TO GET ME OFF HER LINE!!!! I asked her to give me the e-mail address of the EXECUTIVE OFFICE for Whirlpool. She claimed that she did not have their e-mail address and that the only way to communicate with them was by snail mail. I checked the internet and found a telephone number for the Executive office in Mississauga. I called them. The menu asked to push 5 for... get this... CUSTOMER EXPERIENCE... I pushed 5, followed by a bunch of beeps and a busy signal and disconnect. I tried 3 times. So there you go. This is their way of giving you a Customer Experience. Then I found a number for the Executive office in the USA. I was able to reach Latisha from the executive team and she assured me that if I were a USA resident she would have that motherboard shipped to be by courier right away. Because I am in Canada she was going to contact them to give me a call but that now I had to wait till Monday. 4 days to get back to me from Canada. Yet when it comes to service and parts, everything is arranged in the USA and everything comes from the USA because it is more cost effective for them. Who cares about the consumer. By then the motherboard will have left three days to arrive. 7 days take away 4 equals 3, take away a day for courier, depending on what time they call me on Monday, otherwise you have to take away two days, and then it will be all for nothing. But again, they must have so many complaints at the EXECUTIVE LEVEL, that they cannot call right away. So folks, note that Whirlpool has not recalled these machines with a defective motherboard, they are still selling them to unsuspecting consumers. They are not making an effort to send them out quickly or keep some in stock locally. BUT THE WORST OF ALL IS THAT THEY ARE REPLACING THE DEFECTIVE MOTHERBOARDS WITH OTHER DEFECTIVE MOTHERBOARDS!!!! This is outrageous!!!! I shall update my review once I hear from the very busy executive office for client care, and again once the new motherboard goes in. I shall post my order number and receipt when I update this review as my husband has all this and he is away. However I can give a work order number from service: **.

I purchased a Maytag Washer Bravos Quiet series 300 & a Dryer Bravos Quiet series 400 w/ steam in June 2009 from Lowes. I cant express my dissatisfaction in strong enough language with these products. From the time they were installed there were problems.The Bravos series 300 washer: Quiet? Never. The thing sounds like a huge motor whirring around my laundry room. Several times, a coin got stuck in the motor and created a clanking sound that had to be fixed. Ive never had a washer that allowed coins to enter the motor. I cant close the lid on the washer until the whole unit is dry because of the mold problem. I dont feel the washer really gets clothes clean. When we purchased the unit, the Lowes salesman stressed that we could fit a large bedspread into the oversized tub and get it clean. This didnt turn out to be true. The clothes tangle terribly and the unit is off-balance with any kind of a larger load. Ive been forced to purchase the extended warranty because of the complete & total lack of confidence I have in this awful washer (same goes with the dryer).The Bravos series 400 Dryer: This unit never dries. All the setting that should be used with the sensor never work which causes a huge problem. I start out on a particular setting with a stated time limit say, for instance 45 minutes. 45 minutes later, I look at the dryer and theres 1 hr of time still left to go! The dryer just runs on and on. Ive taken to using only the timed dry and I start out at 1 hr, then check it every 10 minutes or so. This is very hard on the fabrics and has caused the useful life of my clothes to be greatly diminished. Also, the stupid thing will start to beep and I cant figure out why. Using this dryer has increased the electricity costs to us.I cant stress enough to STAY away from these products. I purchased Maytag because of their prior good reputation. That reputation is in tatters now. They should recall this product and replace it with products that actually do what they advertise!

We bought this he Maytag washing machine about 3 years ago. I have hated it from the start and should have put a review right away because it is a piece of cr#&. It does not save any energy because I have had to rewash loads because clothes come out still dirty, lint still on them, sometimes even dry spots on clothes. I did a wash today and chunks of HE detergent still in the clothes. I am rewashing a load right now. I now have to do a presoak hoping that will help the load come out cleaner. So dont waste any money on Maytags HE machines as I will never buy another one.Being an environmentally conscious person, I thought HE was the way to go but it doesnt save any energy when you have constantly run a laundry twice to get clothes clean. It also does not do a good job spinning as clothes are still very wet. I hate this machine and I am thinking about junking it even though it still runs. Very bad purchase.

I really liked my Maytag Bravo X washer. Until, at less than 2 years old, it started having issues. It all of a sudden starting sticking in the spin mode, then it wouldnt turn off even though the cycle was complete. I have to pull the plug out of the machine it to stop from continuously running. I was charged $104 to have a certified tech come out for 15 minutes and recalibrate it and it worked for another month. It started having that same problem again and now, I have learned I need a new control board, which costs over $200, plus labor, over $60. The Maytag service rep I spoke with was very pleasant when she told me she spoke with her supervisor and told me there was nothing they can. So now I dont like my pretty new machine at all, and have to decide if I should stick almost $300 into getting it fixed again, or buy a new washer, NOT A MAYTAG! As I voiced my complaint on the Maytag website I saw that there were many of the same complaints about the faulty control board and am wondering what does it take to get a recall?

I purchased a top load Maytag washer the spring of 2019. My clothes come out partially dry, with a film/residue, and debris left on them. I was told that they use considerably less water; however there is not sufficient water to wash away small amounts of anything left on clothes. I have contacted Maytag 3 different times. Each time my concerns have been dismissed. The only solid advice they gave me was to use less soap, which hasnt changed anything. They also told me to clean my clothes before I put them in the washer (we have no children at home; Im not talking about really dirty loads). They told me there was nothing they could do, and I was just stuck with the washer. I am completely dissatisfied with this product and the Maytag service. I would not recommend their washer or their service. The dryer works just fine.

Maytag Refrigerator Model MFI2665XEW6 piece of junk. * Builds up ice on bottom of freezer * Bottom freezer door will not close * Annoying alarm sounds* Water leaks on floor

2 weeks after my warranty is up, the control panel is shot. They used to make quality products and that is why I purchased a Maytag. I had before this a very cheap dishwasher from G.E. and it lasted 9 yrs. I cant believe it is already broken. Do not buy Maytag!!

We purchased a Maytag Bravos Quiet Series 300 in June 09. The dryer timer has malfunctioned since shortly after purchase, it will add time near the end of the cycle, sometimes as much as an hour or more. We have had factory authorized repair firms (tried several) attempt to fix the problem both during the original warranty and extended warranty periods. They replaced the mother board twice and the moisture sensor on another occasion. All to no avail. Maytag has been worse than useless in the whole situation, and now will do nothing. It seems our only choice is to live with it, keep replacing parts, hasnt helped yet, or buy a new dryer. You can bet it will not be a Maytag!This situation is dangerous, if left unattended when the malfunction occurs the clothes and interior of the dryer get extremely hot. It is a potential fire hazard.

We purchased a Neptune washer/dryer combination with pedestals a few years ago. The washer vibrates so violently that I had to block it between the dryer and wall to keep it from walking across the floor during the spin cycle. We had a technician come out, and he stated that the unit just needed to be balanced. The level I used showed the washer balanced in all 4 directions. Then he said I had to balance it with the machine running to stop the vibration. That didnt work either. I had previously installed vibration dampers and the technician told me that makes the vibration worse. When is someone going to file another class action lawsuit against Maytag, as there appears to be thousands of complaints for this same washer?

I bought a Maytag dishwasher from Home Depot August 2018 and it has leaked soapy water every 3 out of 5 times that I run it. Home Depot said they dont cover installs after 2 weeks and to directly contact the manufacturer for service. Maytag sent out a tech 3 times but they werent able to replicate the problem, so nothing has been done to fix the dishwasher even though Ive shown the tech different photos of the dishwasher leaking. The service tech said they will now charge me $90 to return, even though the dishwasher is still under warranty and not repaired! Ive owned many different dishwashers (rentals and houses) without any problems. This is the first Maytag brand and it is horrible. I will never buy another Maytag and have warned all of my friends and family.

Washer Bravo MVWX655DW0 - Maytag has shipped the wrong part twice, sent me the right part which is faulty and the 4th one arrived today. I have not had a washer since 9-16 October 9, 2017. I am writing to tell you about my experience that Ive had with Maytag over the last 30 days. I have owned several Maytag and Amana appliances in the past; along with owning several currently. Over the years, weve had a wonderful experience owning these appliances however the last 30 days is one that has been unbelievable. On September 18 on a Monday early in the morning I called Maytag service line. I spoke to a young lady who had difficulties finding me in the system and did not know how to make an appointment to have a Maytag repairman come to my house to look at my washer. I did not take down her name as I thought and trusted that the company was acting on my behalf and would take care of me.I spent several minutes explaining to her that I did not live in Indiana that I lived in Iowa and that I would need a repairman who is close to my hometown. She continued to give me phone numbers with area code 407 in Indiana and then kept repeating some type of a ZIP Code 49 something for Indiana. I explained to her four different times that the zip codes in Iowa start with a five and the area code would be a 515 number in the area she was looking at. She finally gave me two phone numbers, one that did not work. I asked for a repairperson out of Jefferson. She told me Cranston Repair and gave me the phone number. She told me to call him. I told her that I would go with the Cranston repair since Jefferson with my hometown and it was close to where I lived.I then asked her if she would make the appointment. She told me she didnt know how to make the appointment and she kept messing up with the system. Not sure if it was her first day or not but that was fine so I said “never mind I will set the appointment up myself. I then asked her to double-check to see if our new Maytag refrigerator that we just purchased was registered. She told me she did not see it but all I needed to do was call back the next day with the model and serial number and anybody I spoke to on the phone could go ahead and get that registered. I thought I had registered online; I only wanted to double-check but she didnt see it so I assumed I did something wrong and then would make the call back the next day.I called Cranston repair and scheduled an appointment with the repairperson for the next day Tuesday, September 19. Repairman came the next day on time, looked at the washer and found that the transmission had gone out. I had purchased the washer just shy of two years ago. The repairman said that he would have to order the part and would let me know how long it would take and would return to fix the washing machine. He called from my house and was told that the part was on backorder until October 5. After the repairman left the house I decided to call Maytag back and express my disappointment in the product as Maytag says they stand behind their products and the fact that it was not even two years old and that a transmission would go out. The individual I spoke to this time, Antcwaniqua? Not sure about spelling, listened to my story. She also told me the part the repairman ordered was not correct.I needed part W1 1132267. She said that was a substitute part for the correct part that I needed which was W11035204. I told her that the part number ending in 204 we were told was on backorder until October 5. She said no, the part may show that in the system for repairmen but Maytag can locate the part in a warehouse, it would be shipped in 3 to 5 days. I told her that he had called a place in Davenport, Iowa. What she would do because of all the issues I was having was she would go ahead and ship the part out to me at no cost in 3 to 5 days.I wasnt sure about that warehouse thing. It didnt sound convincing but at that point I had to go along with it. What was shipped out to me was the substitute part W1 113-2267. At this point she told me that I would have to pay to have the part put in; I agreed to that on I want a new washer or I want my washer repaired within 72 hours at no cost. I have not had a washer for 3 weeks plus. Repairman in coming Friday and I am not confident that the 4th gearcase part that came today will work either.

I use a late model Maytag front loader. It does a great job cleaning and uses very little soap and water. To date I have NOT had to call the repairman to work on it. All in all I am VERY satisfied.

Both the microwave and French door fridge handles are crap. The microwave has completely broken and the fridge is very loose and will soon break, Im sure. Both are less than 5 years old. I will never buy Maytag again.

Well I must say I concur with all previous posts. I just replaced my Bravos with a Samsung after my jet plane of a washer died. My repair guy said it was not worth it to fix it. I had already replaced the shocks two years ago but I did have mine for 8 years. I have had the same problems as previous posts - rust, smell, holes, broken, too expensive! Hello to Samsung!!

I have a Maytag Bravos washer bought 6 years ago. Recently, it started giving trouble by stopping at spin stage. I contacted a local service company and they immediately told me even without looking at machine, that it is a control board problem and will cost a lot to repair and suggested to buy some other company washer instead of repairing. They told it is the third similar complaint this week. But I contacted Maytag and they suggested their factory authorized technician who could not correctly locate the problem but charged for the visit. Later he also came to the same conclusion. Thus my previous washer from another company lasted for more than 20 years (Still in working condition), this washer required a service with a cost same as its price!!!

The Maytag MFI2568AES refrigerators ice maker is broken and we cannot get a replacement unit. Whirlpool who now owns Maytag is of no assistance. The unit is two years old. I understand planned obsolescence but this is ridiculous.

I am not complaining at all about my dealer. I am complaining that I also am like the many others with the French door fridge/freezer. The bottom of the freezer freezes up and water pours all over the floor. I thought that Maytag was a good appliance, but also had problems with the pump and drain on my washer. Both of these are only 2 1/2 years old.

I purchased a product less than one year ago. The clothes are getting snagged in seam on interior of the front panel. I went back to the store and felt the same gap in the seam on the panel on a floor model, so I know it is not just my machine. I called Maytag service and a representative acknowledged the problem but also said that if there is no fix for it, I would be charged for a service call even if no part was replaced- quite a contradictory statement. She said she doubles as the Complaint Department. If this is a manufacturing defect, it should be replaced. The front panel should be recalled.

Quiet, efficient and leave you with clean dishes & utensils at the end of its multicycle cycle. This unit can self-clean and is always beautiful with its shine finish stainless steel interior. This unit can be installed by any user as it comes with everything one will need to complete the installation.

Gave up a very good old washing machine to update to a newer one and so we got the Maytag bravos 300. I thought Maytag was a very dependable name and product. The warranty went out. 2 weeks later, the water pump went out. I had to pay to have it replaced. Then after that it started making noise that got louder and louder and now it sounds like a thrashing machine. And now it has started leaking water out of the bottom. So its going in the scrap pile. What a loss of money - the worst investment I have made. For what I paid for this machine, it should have lasted for many years to come. The washer I had before this Maytag I had for 16 years - no problems at and it still worked great when I gave it away. Maytag use to be a brand you could count on. Great craftsmanship has been taken away and monetary gain has taken over. I hope no one else has to go through this nightmare that I have. Maytag they should have to give peoples money back that we all worked hard for. Going with a LG now, hope its a good machine.

I have Maytag refrigerator that is only 2 years & 9 months old that I am told by a service tech that it has a sealed system leak. So the unit runs it just wont get cold. I have lost all the food that was in the refrigerator & freezer and I told by Maytag that its not covered under warranty. The tech gave me a ball park quote of $600.00- $700.00 to repair the unit & I lost at lest $200.00 or more in food. I cant believe a new refrigerator wont even last 3 years & they wont fix their problem. So much for buying American made products. Whirlpool YOU SUCK & SHOULD BE ASHAMED!!!

I’ve had this new stove just over a week. Used 3 times (I just moved). I have cooked on staying already on the ceramic top. I’ve had a ceramic top stove for over 20 years with barely a mark in it. Terrible. I’ve left a message with the store with no reply.

Maytag has always been my favorite lasts forever no problems at all till something perforated the pump but was fixed promptly. I had my maytag till I moved and left it with my son so I do not have it now but I'd buy another maytag as long as it's not one of those water savers. Do not like those because it doesn't use enough water to rinse out the soap properly like the older original machines. Maytag is strong, durable and worth every penny. If I was buying another washer It would definitely be a maytag. They wash clothes thoroughly. Of all household appliances if have to have a maytag washing machine and my favorite vacuum cleaner. Maytag washing machines are by far a ten next everything else I've tried.

My Maytag Neptune washer also has a problem with mold build-up and now the door lock assembly is totally gone. I was unaware of the class action suit or I would have joined. I am just disappointed!

When our ice maker (Model # MF12269VEM10) stopped working, we contacted Maytag, only to be told that the 1-year warranty had expired. So we had no recourse but to contract a repairman. He replaced the valve (and in the process, because of Maytags decision to use plastic tabs instead of screws, the tabs for the filter housing broke off in his attempt to reach the rear of refrigerator where the valve went and we had to pay to have the housing replaced, also). The new valve did NOT fix the problem. Water continued to run out of the water dispenser after you removed your glass. We re-contacted the repairman who returned and proclaimed that there was air in the lines and it should work itself out over the next several days. Yet that night, I noticed drops of water running down the control center and filling the drip tray. I placed a towel on the floor and emptied the drip tray several times that night, before turning off the ice maker completely the next day.Unhappy with the original repairman, we contacted another who came out and discovered that the new valve was leaking from the top. That is when the filter housing broke and we had to use duct tape to hold it in place while the new repairman ordered a replacement. He tightened the valve and cycled the ice maker several times only to discover that the water overflow switch on the ice maker wasnt working, thus water was overflowing into the ice maker container. He turned down the water pressure to the refrigerator, and we tested it again. All seemed to be well until the next day when no ice was released from the ice dispenser. When I removed the ice storage bin, I found everything frozen from water overflow. I turned off the ice maker entirely and contacted the repairman, who ordered a new ice maker, which took about a week.After the new ice maker was installed, along with the new filter housing, the repairman cycled the unit several times before leaving. Yet by the next day, the ice in the storage bin was frozen in place again (I have pictures), and we contacted the repairman who ordered yet another ice maker. It took yet another week for the part to come in. After it was replaced, I monitored the ice container each time I heard ice drop into it. The 1st time there were a few drops of water in the bottom of the ice maker. The 2nd time, there was a 1/4 cup of water in the bottom. I immediately contacted the repairman to let him know and turned off the ice maker yet again.I find it hard to believe that a new valve, fresh from the package, and 2 (TWO) ice makers, fresh from the box, were all faulty. The repairs started on February 25th 2015. It is now March 21st and the ice maker is still not repaired. The 2nd repairman is doing his own research into the problem (for which we applaud him!) and now we ask you for your feedback as to the problem and how it can be solved.

Washer exactly 3 months old, will not work. Maytag can tell you nothing, they just want your money. They called a repair service in our area, never heard from them. Here we sit no way to wash clothes. And they say will charge to fix it. WHAT IS WRONG WITH THIS PICTURE. FO NOT BUT MAYTAG ANYTHING.

I purchased the Maytag refrigerator MFF2055DRM on 7/7/16 new. It was suppose to be stainless steel; but now I am seeing rust spots at the top and bottom of the French doors. I clean my refrigeration weekly and find it odd that now it is rusting. Also, I am able to place magnets on the doors - which should not be for stainless steel. In addition, I spend over $100 a year replacing the mandatory filters. I must also place the setting to high to maintain my milk and juices. I must also have to place them in the very back of the refrigeration. I am a single senior and my refrigeration is not overloaded with food; nor am I constantly in and out of the refridge. Not very happy.