The pulley on the dryer vent keeps falling off due to poor design. We had a repairman fix the problem under warranty, but the dryer was purchased in 2010 and this is the third time it has fallen off. I have taken the dryer apart and repaired it myself, as I am quite capable, but I called Maytag Customer Service to see if there is something else I should do or replace. They told me they never heard of the problem and they would recommend a service man repair it, which would cost me money and It wasnt needed. No updated part was recommended, or any other help at all, for that matter. I am very unhappy with the Maytag products and will never buy anything again.

Bought Maytag Bravos in 2010. It does not clean but worse than that it rips clothing (for example: loops off pants, holes in pjs, tons of ripped towels), so many items of clothing torn that I cant keep count. Today I had a pillow case ripped apart (see image). I have had four sheets ripped that I can no longer use. Maytag should have recalled this washing machine. I have the Maytag Bravos dryer also and the drum was on backwards on it when I bought it.

We bought the Maytag Bravos washer & dryer combo from box store. I wanted an extra large capacity washer to accommodate king sized bedding, and having fewer wash loads in general. Cons: 1 - This machine is not energy efficient when each wash load takes 1:30 to 1:50 each load. 2 - The detergent/fabric softener/oxi dispensers are a joke. Water dumps into every compartment at once. And if there’s still detergent left by the rinse cycle, well you get the picture.3 - The “Bedding” setting is the only one which will provide enough water in the tub to get anything wet. Since there isn’t any type of agitator the clothing/bedding just floats on the surface in dirty perfumed water. 4 - With any of the other settings the water level is so low it doesn’t always get everything wet so items are not being washed properly. At most maybe 2 pairs of jeans or just a few t-shirts can be washed on the “Normal” or “Power Wash” settings. 5 - Because there isn’t an agitator, clothing gets knotted up. Dress shirts, dress pants, jeans, towels, you name it, everything comes out of the washer in a knotted mess.The Bravos XL Dryer: My only complaint with the dryer is that it allows a good amount of lint to pass through into the machine. Then it’s difficult to get any type of lint brush into the vent area to remove the lint. Dampened lint in the machine can make clothing smell musty and nasty. I had to call a service to remove lint from the dryer & ducting because of the odor lingering from the inside the dryer.

I purchased a Maytag washer and dryer three years ago. They both were taken to recycling and I received eleven dollars for both of them. They were both horrible. The transmission went out on the washer. The repairman said not worth fixing since it would cost $600.00 to repair. He said Maytag appliances are being outsourced and are not what they used to be. Even before the transmission went out it took forever to wash and the clothes smelled when I took them out of the washer. The dryer quit heating a few days after the washer went out. The repairman said it wouldnt be worth repairing it either. I will never buy another Maytag!!

Bravos x - Ok so I was checking on my washing machine balance which is off. I came across the reviews and find how horrible the machine is! Grinding at last cycle, and not wringing out clothes on some loads. I thought grinding and wringing out was to be that way since it did it from day one. I thought I just needed to adjust clothes to wring out. Balance was taking out some clothes but it was put in properly. Boy was I wrong. Im so pissed after reading all your reviews. Im going to contact my daughters who works for attorneys about false advertisement and selling something they know is crap.

My Maytag microwave MMV4205BAB gave out this a.m...again. I bought it in 2008. The repairman has become a close personal friend because he visits so often. In Jan. 2012, I bought an extended warranty, which expired in Jan 2013. This is the best example of planned obsolescence Ive ever seen. We wish we had kept our GE with the broken handle, which we had for 20 years with no other problems than that. If you are wise, do not buy Maytag.

The dishes need to be washed off to be sure they will be clean. It holds a lot of dishes. You can put it on a short wash or long one. Leaves water on base of glasses sometimes. Holds moisture. Heavy wash, normal wash, light wash, rinse only, auto clean, delay 1-9, heated dry, sanitize, tough scrub, extra rinse. Regular size 24. Beige color. Electronic buttons. Maytag Quiet Series 200: I do not like the racks for putting dishes in. Otherwise it holds a lot. It does not clean dishes if you do not rinse them off first. If you run the dishwasher immediately after putting dishes in it will clean them off. Sometimes it leaves water standing. Even with what I have said I really like this dishwasher. We have had the dishwasher a long time. We use it at least 2 times a week.

CHRISTMAS morning Set oven to 325 for ham. Control board caught fire and burnt wires and burnt inside of rear cover. It got hot enough to char the wood wall behind stove. This could have killed my family on CHRISTMAS.

My refrigerator outer case has felt very warm to the touch at the section between the top freezer door and the lower refrigerator door for several years. I thought this was a normal function of the defrost mode. It is now very hot to the touch so that I cannot touch it for more than a few seconds. I dont know how long it has been like this. This cannot be normal. I did some online checks and found that there was a Consumer Product Safety Commission Recall release #09-145 and 09-322 that warns about the same problem I am having. My model # (MTB215) matches the recall, however, the last two characters in my serial # is WQ does not. This problem appears to be very consistent with the problem in the recall releases.

Maytag dishwasher model MDB7759SAB, 1 year old and control panel will not work at all. Maytag site does not recognize model #, got part numbers off parts and cant find the parts. Looking for control panel, cant find black one and others are back ordered for weeks. After reading other peoples problems, it seems Maytag would correct the issue.

MDB7749SAW - 22 months @ an initial price of $599 and control panel lights become increasingly erratic and finally machine fails to respond to reboot (unplugging) after the third time. Repair man over the phone is familiar with the model and estimates parts at $160 + $115 (gave me a discount) + $125 service call for $400 to make the Maytag run again. Bought June 28, 2012. Installed September 2012. Becomes trash July 2014. Wish I could be more helpful... but if I had purchased the service insurance agreement, it would have run about $90/year... that would have been an extra $180 for a total of $712 including sales tax. So, I had a dishwasher for about 95 cents per day. Nobody rents them. I cant give it less than one star or I would. As a new buyer I was not informed.

My new dishwasher had a defective board and worked erratically. Shortly after the warranty was up it stopped working completely. I contact both Maytag service and Home Depot on several occasions with no satisfaction. This a well known defect. Apparently the board replacement and service would cost in the range of $250-300. Too much for me as a senior on fixed income to justify. No dishwasher for almost a year. I then read an article indicating there was a class action settlement in California on the same make and model. I called Maytag again and after spending 2.5 hours on the phone I finally reach a person who sent out a service repair person. This person showed me a memo confirming the problem with the board. No recall but... if a customer is persistent they will give you the board. Finally new board installed at no charge.

If you have a second floor laundry room, DO NOT, and I repeat, DO NOT acquire this washing machine!!! The Bravo MCT model washer is TOO loud (during spinning cycle), and for some reason, the clothes come out all tangled up. Some cycles are a waste of a cycle, and most cycles take a bit longer than my former washer. I miss the cycle choices I used to have on my former GE Profile washer (GE does not make that model anymore hence my changing brands). For the most part, clothes come out clean; thats why I give it a two-star rating instead of one. The dryer: Must dry every load in low heat so it doesnt come out extra crispy and wrinkled up. Although I generally have to run a second drying cycle, low heat does work great and the clothes come out ready to be folded/put away.

Im very pleased with both the washer and the dryer. The front-load washer is very efficient with many washing options dependent on items being washed. Spin cycle spins very well which lessens the dry time of the washer.

Bought Maytag Electronic Washer and Dryer on Feb. 7th 2020. On July 10th control board went out in dryer. 3 weeks without a dryer and hanging clothes in 112-118 degree weather in Arizona. I am 77 years old and too old for this. Dont buy Maytag!!. Had Whirlpool Washer and Dryer for 22 years. Never a problem, regret buying a Maytag.

Our prior fridge died on a hot long weekend in July 2020. Desperate for a fridge, I ordered any fridge that could be delivered the same day. Received a Maytag which totally died 3 months later! Now I am waiting for a part (which apparently the Manufacturer has 100 in their inventory but havent distributed them to the source that ordered them). This is just the worst service I have ever experienced with an appliance. As so many people have said, I should have waited and ordered a European appliance. They are built beyond perfection and have excellent service.

My stainless steel french door refrigerator started to rust 4-5 months after purchase. Upon contacting Maytag/Whirlpool I was advised that this is cosmetic and the cosmetic portion of my warranty is expired. I think this is a poor grade of stainless steel and should be recalled and/or replaced. I would not recommend.

Purchased a Maytag Electric Range on Jan/9/2016 and delivered Jan 12/2016. To start the Aqua Steam clean is for the birds. Does not clean worth a darn. Model MER8600DH cost $823.33 and I thought this unit was awesome until December 2018. The oven makes loud bangs and it’s not metal contracting or whatever. I stopped using my oven. Tonight my top burner started snapping like an arc or short. Yup that’s it for me. I was thinking of buying a Maytag Gas Range as I was brought up on gas and I have a plumber coming this weekend to plumb for Natural Gas but after reading all the negativity on the gas ranges as well I absolutely will not be buying a Maytag now or ever! I expected more from Maytag. :(

We are extremely frustrated with this machine. It takes an extremely long time to go through the cycle, compared to past washing machines, even when it is working. It rarely completes the cycle and often goes back to wash and stops. We have no way of knowing if it washed or rinsed or what. To get it to finish, we have to turn the dial to drain and spin. The clothes always come out tightly twisted and tangled up and have to be untwisted and items pulled from each other....so they are extremely wrinkled! This is the first and last Maytag product we will ever buy. We HATE it!!! I would say it has been a lemon from day one but Home Hardware was no help when we complained. We tell everyone to stay away from this product.

We bought this washer in February of 2010. We had the pump replaced under warranty in January of 2011, and the pump appeared to have a hole in it from some type of hard object that had gotten inside the pump and damaged it. We then replaced the L-shaped hose between the tank and the pump because it had a small hole in it - very thin rubber. Last week, the washer was leaking again and the service technician said that the pump housing was cracked due to a penny rattling around inside the pump.This washer performs very well when it is working but it seems to be too fragile to handle on normal usage. The Whirlpool washer we replaced with this one ran for 23 years with no problems before it finally went out. From all appearances, it seems that every failure we have had with this washer has been due to damage from foreign objects getting trapped in the pump. Is there no screening mechanism to prevent hard objects from entering the pump? This seems to be a design flaw more than anything.

I know that Maytag wants to conserve water by adding as little as possible... But when the damn machine puts hole in 5+ shirts Im not a happy homemaker!!! At first I thought it was the dryer so I had a repair come out and explain Im not the first person that complained of this issue. Its too late for me but Maytag needs to be aware that they are losing, what I thought to be, one of the top washers reputation.

I bought this Maytag French door model MFF2258VEW2 in 2010. Within the first year, it was freezing my vegetables. They sent someone out to fix it. Thank goodness it was under warranty. The man laid the bill down and it was over $800 to fix it. Six months later, it froze up. I called and they said they would send someone out, but I would have to pay for it. Im on disability and cant pay that kind of money. I got someone to come out and fix it. Well, guess what? It has started freezing my vegetables again. This is the third time this thing has gone bad. What do these people think they are doing putting things out like this? I had a Maytag for 30 years and never had any problem with it. So I saved and saved to get me a new one but I will never buy another Maytag. The company should have to replace all the refrigerators that are like this one.

This appears to be a common, known, well publicized problem - freezer drain clogs and needs to be either changed or repaired with a fix, a free replacement part for the drain seal. Easy to install, takes 15 minutes. HOWEVER Maytag will not give you the part!! In order to take advantage of Maytags correction for a well known, chronic, manufacturer defect, you must engage an authorized service person for hundreds of dollars and wasted vacation time waiting at home for them to show up. Unlike any other product, recall this one is not free. My kitchen is full of Maytag products; dishwasher (not so good), range and a refrigerator that had to be replace when the compressor went out after six years. However this is the last straw, Ive learned my lesson, seen the light, THIS IS THE LAST MAYTAG PRODUCT I WILL EVER BUY.

We purchased a new Maytag Bravo washer and dryer on March 4, 2011. On January 26, 2015, our washer stopped spinning the clothes. We purchased these appliances while preparing for retirement, thinking we would possibly never have to purchase them again. There is only two of us! Wrote to Maytag (when it was still Maytag) and got a response of So sorry **, we can fix your washer for $319.00. We could buy a new washer for not much more than that!!!!!

My four year old Maytag stove blew out the lower heating element in the oven. The model number is MER8880AW. I removed seven small screws to confirm what the problem was and remove the element. That is a short life span for a stove element. My wife checked our paperwork and thought it indicate the part was covered on the 10 year warranty. Called Maytag at 9 AM and went through the press numbers thing, being put on hold, call dropped, told they were not open twice, etc. Finally got a person to talk to at 2:45 pm. Yes the part is covered under warranty, but no they will not give me the part.A repairman must plug it in and put the seven screws back in. This will cost me a lot more than the $50 the part cost me at the local appliance store. 10 year warranty. Wow, WORTHLESS! There WILL NEVER BE another Maytag or Whirlpool in my house. Making a big deal out of their warranty when they are going to soak you bad for a simple install is just plain dishonest.

I had six service calls, one was a few months after purchase when under warranty for loud noise. I bought it in 08 and since then during the last 6 months, its freezing in the refrigerator. Service person is upset. I contacted corporate and they do not care and told me I should have bought their warranty. Yes, they had to be here when it was under warranty. Still freezing, they played with air hoses, replaced the temp panel and did everything they can, with no results. Theyre giving it one more try and it is going to be hooked up to the Silverado and put on I-75 with a sign on it. Do not buy from this company. Terrible service. I emailed CEO and no response. I just tossed a tomato and strawberry on the tile floor. Yes, buy American. They moved their plant from Indiana (union) to I think TN for non-union. Well, get what you pay for and the employees get what they are paid for. I work in the building business and everyone knows not to buy this product! Just throwing your money away. One good thing is if you like frozen beverages, this is the product to buy! Never again! Receipts in hand! Romney probably owns the stock! LOL

We purchased a Maytag Gemini gas range last year in April and the extended warranty. The ovens have not worked correctly since we bought it. I never do this type of thing, however, I am just disgusted! I am going to exercise my right as a consumer to express my customer dissatisfaction and share using the social network. I dislike Maytag and even dislike A&E factory service more! I have never experienced such bad service on a new appliance. What is even more concerning and the reason I am posting this warning is there appears to be no recourse! I googled search both companies and the first things that came up were complaint pages. How sad! Buyer beware! If you buy a new appliance, research the warranty provider. It appears that Maytag has laid off the Maytag repairman and went to a lost cost unskilled service provider! A&E repairman has no idea how to fix the oven. He replaced the part. 4 weeks later, came out and walked in the house and did not even look at anything and ordered the same part again. He told us he would be back the following Friday. He did not schedule an appointment. I called on Thursday before he was due to show on Friday and A&E told me I had no appointment scheduled. They told me to inspect the parts that were shipped. I told them I would not even know what I was looking at! They told me the repairman would be back out between 1-5PM on Friday. No one showed. At 2PM, I called and A&E said the repairman must be on his way because he did not call and say he wasnt coming. But again, he did not show! I made no less than 6 calls to A&E and Maytag after that! A&E would not escalate the situation to a supervisor and on call number 6, when I finally got to an advocate, they told me to call Maytag! I have taken 4 days off as vacation to be home for the repairs and this last day was the final straw. When I researched escalating paths for both companies on Google, the first thing that came up was whole pages dedicated to complaints for both companies!

Major issues with the Aqua Lift Range. Takes forever to preheat the oven, 15-20 minutes to reach 375 f- 400 f. Aqua clean cycle not efficient and does not clean at all. The stove top is impossible to select and keep the heat consistent. When adjusting the heat up or down when you slightly move the dial it overreacts. When moved the heat sways may more than selected. The fridge works well but the bottom drawer is way too flimsy and it wont last a long time as it will crack. This is our first purchase of Maytag appliances and it will be our last. Our old 10-year-old stove worked much better than this one. Sincerely, Russell ** & Linda **, e-mail= **

Bought the Maytag model MFI2670XEM and within 6 weeks freezer wasnt making ice. Repairman came and fixed it, within a couple weeks same problem again. It was fixed and within a couple months same problem. Fixed, but makes very little ice. Now 18 months later after purchase freezer is leaking water onto the floor. Very disappointed!!! After reading other Maytag reviews I am worried I will have to dump this relatively new refrigerator and buy another (wont be a Maytag) and our upgraded dishwasher from Maytag is terrible! I hand wash all my dishes before putting them into the dishwasher. The smallest bit of ketchup or sauce is not washed away in the wash cycle. Our Maytag stove/oven seems to not heat correctly, as well. Internal temperature gauge reads 5-15 degrees off all the time. Thumbs down Maytag! Extremely disappointed with Maytag products! Will never buy again!

We purchased a Maytag MFI2670XEW6 french door/Bottom freezer refrigerator in July of 2012 through Home Depot and for the past 6 months have had to scrape ice off the bottom of freezer every 5 days or so to prevent water flowing on floor. I see so many exact complaints from people that I am just fuming! Cannot believe this company is not backing their products up with that issue. A recall should most definitely been done. I grew up believing Maytag was top of the line but I am wrong. I bought this to replace a 16 year old GE refrigerator (side by side) which I never had any problem with and now I regret not replacing it with another GE. I havent contacted the company yet as I thought I would check complaint reviews before I did that but it seems that the company is just treating their customers like dirt. To spend $2200 for a refrigerator and have problems within the first 3 years is unacceptable!!! They had better start going good on this problem or face the fact that they will no longer be in business a short time down the road. The best form of advertising is word of mouth and online reviews and it looks like they are going to lose a lot of customers with the direction they are taking.

Purchased Maytag 4000 series washer Feb. 26 2011 - within six months Maytag warranty replaced the drum and bearings, within another few months Maytag worked on the drum again. Year two started out with the warranty contract replace the drum and bearings again. Oct 1 2014 called for service again, the drum not moving and having to wait 2 weeks for Tech. to checkout the machine then order parts. I have 7 children at home and that didnt matter to anyone. After reading online the number of 4000 series Maytag machines with this problem somebody needs to make Maytag recall and replace them.

I paid $958 + tax for a Maytag Bravos washing machine in August 2008. I live by myself, so the machine is not overused. Nevertheless, it began to sound like a jet airplane during the spin cycle. And then in May of 2012, it failed with error code F51, catastrophic failure. The machine was not even four years old. I called a certified Maytag repairman. In less than 5 minutes, he told me the cost to repair would be about $900, and then he charged $115 for the service call! A call to Maytag resulted in Im sorry, there is nothing we can do.

This oven has been used so very seldom that I didnt feel I could rate it until now. We use the oven 1-2 times a week since purchasing it in March of 2018. There hadnt been any reason to use the Self Cleaning part of the oven until last week. I have had a oven with self-cleaning for 20 years and the oven went out so we purchased this one because of its sleek look and features. However last week I decided to use the self-cleaning setting on it and came home after being gone all day to find that the house smelled like it had a fire burning in it. I ran to the oven to find the whole inside cover in a white powdery substance. It looked like a snow blizzard had gone on inside of it. I was use to a small amount of white residue being inside the oven after it finished and it just wiped right up. We spent hours vacuuming it out then scrubbing it down with vinegar water and a sponge with a scouring pad on it. The casserole spill was still on the bottom, most of the enamel is gone and the glass will not clean off. I did not use any chemicals in the oven prior to turning it to the self-clean mode, I believe that it overheated and burnt the enamel off and distorted the glass. Whirlpool offered to send me a cleaning kit. I told them that would do no good. I had already scrubbed and used a razor blade to try and clean the bottom and the glass and them sending me different cleaning supplies would not fix the fact that 80% of the inside protective coating on the oven is gone. Now it is a porous surface. A Serviceman was scheduled and he called prior to arrival today and asked me to explain what was going on with my oven. I explained and he said I can almost guarantee that Whirlpool will say that it is cosmetic and they only cover cosmetic for 3 months and that I will have to pay for a $100.00 service call. This is a load of crap. This coating is part of the oven to keep it clean and protect the metal from the high heat of baking in it. This is not cosmetic feature like the outside stainless steel finish or the black trim decor. The inside doesnt look pretty. It is a function. See the photos below. Whirlpool Range Item # 805150. Model # WEE510S0FS.

Okay, on March 2009, we bought this brand new microwave due to our major remodeling. We didnt move into the unit until February 2010, so the microwave was in its box for 11 months. After we moved in our condo, my husband and I had to travel for work for almost a year so our brand new microwave is very slightly, gently and barely used. Well, for the past 2 months, it had been acting up. Sometimes it heats, sometime it doesnt. For a 2 year old microwave, which we paid over $400, I would assume that it would last. It no longer heats up, so I called Maytag customer service to hear her tell me its not covered under the warranty and would cost $269 for repairs and there was nothing she can do for me unless I pay for a technician to come and repair it! No way, I swear it probably got used 5-10 times a month to heat up coffee for about a year. I am sure there are some major quality issues on this model because when I googled Maytag microwave, all I see is the same magnetic problems. I spoke to a group of my lawyers friends. If youre interested in joining a class act law suit, please e-mail me. I hate that people are being taken advantage of by these terrible companies. I cant believe how low quality their customer service and products are. Believe it or not, my $30, old microwave lasted me 14 years throughout my college years until we decided to replace it with the modern stainless steel one. It got noisier in time but not broken and still heats up just fine. This $400+ one lasted me only for several uses. Shame on Maytag, when I have time, I will be sure to write a complaint to the consumer department as well. I will dedicate my life in spreading the word out about their low quality product. Don’t buy Maytag unless you only plan to use it for a year or 2.

This is the second Maytag appliance in less than 5 years to stop working. The first was a dishwasher. I got 14 months use out of before the control panel burned out. Fixed it for $125 only to have it happen again in 6 months and repair company said parts are only 3 months warranty. Cost me $5 to bring to landfill. Now the matching Refrigerator is making a loud humming noise and Ive been told its the compressor.

I have a front loader dryer, model number MAH5500BWW, serial number A9147862ec. All of a sudden, I found water on the floor and after opening up the front door, I see where around the part that sticks of on the inside of the door, there is a big piece of plastic that has broken off and cracked all the way across the bottom of the door and is missing. It is allowing the water to leak down the front of the bottom of the washer and onto the floor.

I would like Maytag to repair or replace this dishwasher. It has only been installed since November 2014. The only button that works is the auto clean. None of the buttons work. I thought Maytag was a reputable business.

I am submitting this review today to express my disappointment with my Maytag washer. This is the Maytag MVWX655DW (Bravo), with Serial# C61842055. In August of 2016 I lost many treasured items due to a flood in Lafayette, Louisiana. My daughter and I were devastated and displaced because of this event. This is also in addition to completing Cancer treatment 2 days before the flood.I lost my GE washer which was a great product. It was a struggle for a long time, but we were finally get back on our feet. I was able to get another place to live, and it was time to purchase a washer. I was told that Maytag was one of the best products on the market, so I decided to purchase my first Maytag washer. This did not turn out well for me, and it was very disappointing. After 9 months of ownership of this product, it is broken! It is my belief that the product may have been defective.I put in a service call, and had a repairman come to my apartment on June 19th. I was told that my washer needs several parts to repair it, including a pump. I have never had this issue with prior washers. My previous washer before my GE purchase survived for over 10 years before it has had any issues. I called on June 26th to ask about Maytag issuing me a new washer or a full refund, instead of repairing this faulty product. I was told no, and was offered and extended warranty for 6 more months and $75.00. I expressed to her that I would rather have a new washer.The Bravo Washer is a very bad product. Instead of taking advantage of customers, Maytag needs to stand by that 10 year warranty sticker on the washer. Please understand this purchase is a LEMON. This washer did not last a year. After all I have been through, I did not need this financial hardship. In the long run, this product will die again. Unfortunately for me I may not be able to afford to purchase another washer. I am still getting follow-up treatment for my Cancer, and it is very expensive. Can someone please re-evaluate the need for a replacement washer or offer me a full refund? This product should not be broken after only 9 months of service.

Two years ago I purchased a Maytag Top-Loading HE Low-Water washer. I have always taken great pride in the way my laundry looks and smells but since this purchase, my laundry no longer smells clean and fresh nor does it look clean. I have always used the same detergent and fabric softener (only now I use the HE version) and it served me well. I have read all of the directions and did as I was instructed. I cannot believe that anyone would actually think that you can do laundry with practically no water. Do the decision makers have not common sense at all? I didnt and still dont believe it but what choice did I have when all of the machines are now HE with low water. I think its terrible that consumers dont have a choice. I have come to realize that low water, HE washing machines actually waste more time, energy and money (detergent and fabric softener).My clothes are not clean, nor do they smell good when the wash cycle is finished so I have to wash them again, using more detergent, fabric softener and energy. The super fast spin that supposedly sucks out most of the moisture, also rumples my laundry with semi-permanent wrinkles (even on the low wrinkle setting) so clothes that never had to be ironed before, now need pressing. I find it remarkable that, with all of the detergent ads promoting washing clothes in cold water to save energy, we are told that if our clothes are not sufficiently clean in cold water in our HE washers, that we should try a warmer/hot temperature. Good luck with that because my machine has several temperature settings but only uses one - COLD! I cannot actually believe that with all of the technology that our society holds, we are going backwards in the basics of washing clothes. Terrible product, terrible quality, terrible results, terrible waste of time, resources and money. Why cant you just leave some things alone??

The door is worthless. I am the only washing machine user in my home and am gentle with my appliances. However over normal use, the washers door has cracked and has had to be replaced twice since it was purchased from Home Depot.

I bought a Maytag Bravos top loader washer and dryer less than 2 years ago. I started having problems with my dryer 3 months ago and after several service calls (and a few hundred dollars), it still does not dry our clothes. I spent over $1500 for the pair and was excited to have a top end washer and dryer. My biggest complaint is with the manufacturer, Maytag - they just dont seem to care. I did not buy the extended warranty for two reasons. First, I bought a nice unit and expect it to work properly for a reasonable amount of time (at least 4-5 years without any problems). Second, they are just a bad purchase and they cost about half of the unit and if you buy a nice unit, you shouldnt need one. I could have bought a new dryer for what I spent to try and have this one work properly. My wife and I spent $600 for our last set which lasted 7 years without a problem; they were manufactured by GE, which I now wish I would have bought another GE. My wife talked me into buying a new pair to accommodate the needs of our growing family. I wished I would have kept the GE pair that was working.I would not recommend any Maytag appliance: they really just dont care to provide any reasonable service to stand behind their products. What a shame. This reminds me of why many foreign manufacturers are beating us at what we used to do best - make products that last and work! The washer and dryer look nice and have many great features, but these dont matter much if they dont work.

I bought a Maytag Washer Bravos XL approximately 13 months ago. To be exact, July 16th, 2016 through Home Depot. Model #MVW8775DW. Since I bought, the washer shakes, and doesnt complete the cycle as it gets stuck on the spin cycle. I have called Maytag and they have sent out a technician... They have told me that there is nothing they can do. I told Maytag that their product was a lemon and this should not happen... And to please it with one that is not defective. Since then, the cycle does complete, but the clothes are soaking wet and I have to run the cycle again, just on the spin cycle.

Nothing wrong with this dishwasher, a bit noisy, but it gets the dishes clean and thats whats important. This was a builder grade installation and it came with the house so I cant really say its the exact model I would have selected had I been given the opportunity to pick my own.

This is not a complaint but a love-letter. I know that todays Maytag Neptune is not the Maytag of old. But Im here to report that Im still using a Maytag washer that was built in 1982! The only thing wrong with my machine is that it occasionally goes off-balance when I wash heavy towels or blankets. Note: We inherited this machine with the purchase of a home in 1991. We were a family of 6, so this machine has done many heavy loads! Im looking forward to celebrating my Maytags 30th birthday, come Jan. 1, 2012. And I would love advice on how to replace it, eventually, with another machine that has just the basics - no bells and whistles, computerized control panels, etc.

I bought my Bravos washer (Maytag Bravos Model # MVWX700XL2) back in 2013. Worst mistake ever, First off the clothes never came out clean, regardless of how diligent I was following the directions on how to use this particular type of machine. Secondly, it started going off balance for every load if I put more than 4 pieces of clothing in. 2 months after having it recently repaired AGAIN for not spinning and going off balance, it is doing it again. It is only 4 years old! I bought it for the Maytag reputation, but now I am doubting that reliability.

I had a Maytag washing machine replaced under warranty back in 2011 via Maytags Extended Service Plan. This took me several months to get done because of back and forth issues with Maytag not wanting to honor the replacement. Executive Support had to get involved after I wrote a complaint on this site. When they replaced this, they sent me forms to extend my warranty, which I did. They never changed the model or serial number so Ive been paying for 2 years now for an extended warranty on a machine I do not own.The new washer broke and I called in for service on 11/18/13. Active Appliance was sent out, said it was an easy fix but they needed to order a part. On 11/20/13 they contacted me to tell me I needed to speak to Maytag because my Model/Serial didnt match with my warranty records. I double-checked these and called Maytag Extended Service and was told that I would need to speak to sales at 866-730-6094. I spoke to someone named Lindsey there who told me that I would need to send a letter in to cancel my policy and request a refund for the 2 years Id been paying for a non-existent unit and that they could start a new policy for me and get a service order in without issue. My call was disconnected during this and when I called back, I was told to call back in the morning to get back to Lindsey because the office was closing and they couldnt do callbacks.I called back on 11/21/13 and spoke to Sam who verified that the letter was needed to cancel and refund but that I would have to pay for the repair to the washer myself and theyd tack on the cost of the new warranty onto that bill so Id be covered AFTER THE FACT. Because the unit wasnt covered under warranty, Id have to cover the costs myself and it had been MY responsibility, not theirs, to make sure that the correct model/serial was on the coverage.Maytag sent me the forms and I would expect them to have added the new information on it...not send me forms with my original washing machine information. Especially as this had been escalated to Executive Support and the person I dealt with there had gone over everything to make sure it all got handled in a satisfactory matter. So for now, Im waiting for a callback from the original rep, Lindsey, but Maytag tends to Stonewall and not return calls so Im dreading how long this entire process is going to take and cost.

I am fairly happy with this ranges performance. I do have a couple of issues on the design. I would like to be able to simmer at a lower temp on a front burner, as I use a large stock pot and a pressure canner occasionally. The smaller BTU burners are on the back and the large pots do not fit over them. I havent noticed any problems with the upper ovens performance...seems to do what I ask it to, including the broiler. I have not tried the lower oven or the convection feature at all yet. Nor have I had to use the self-cleaning feature, yet...almost afraid to after reading other peoples nightmares, though.My biggest concern is the lack of safety with the knobs on the front of the stove top. Several times, the gas has been turned on by my cat simply walking across the front of the stove and stepping on a knob. This allows gas to leak until I notice. It happened again early this morning just before 4:00 am. I was awakened by a smell, which I thought was a dead mouse somewhere (we live in the country in a 100 year old house - mice do get in, thus the cats). I searched the whole house, looking for a dead mouse, until I finally walked into the kitchen and heard the hissing from the stove. Im glad I didnt try to light a candle while I was still thinking dead mouse!After turning off the gas and removing all of the knobs, I opened all the windows to let the house air out. I SHOULD NOT have to remove the knobs every time my stove is not being used! You do have to depress the knobs slightly to ignite the burners, but its too easy. Obviously, the simple act of a little cat putting its paw on the knob is enough to open the gas. This is a serious flaw that could kill someone! Something needs to be done to correct this before someone is killed or a house full of propane or natural gas is ignited and explodes!!! I will be reporting this to Maytag and hope that they will voluntarily issue a recall to have this problem fixed...Wish me luck.

Bought the washer in February 2012 for $900 at a local appliance store, delivery included. Just yesterday (10/16/15) a 5 cent piece of grey plastic flew out of the lid lock mechanism. Thinking this $900 modern piece of machinery painstakingly designed by intelligent people with university degrees would certainly work if I just stuck the plastic part back in. I just popped it back in, the lid locked, and the machine spun away happily (only having to run a correct cycle for an unbalanced load twice! What joy!) Fast forward 40 minutes, I skip down the stairs to go retrieve my flannel sheets (because its October in Pennsylvania, its getting freezing cold at night) and pull up gently to open the lid. It doesnt budge. About 2 hours later, following a screaming match and some furious googling, it was determined we would need two people to pop the entire top off the machine to extract my sheets.So in order to use the washer to clean clothing now, weve been unplugging the machine. Removing the three screws on the control panel (aka brainbox), unplugging the black and white wire from the brain box, taking the control panel off and sitting it on the dryer, and using putty knives to push in the metal clips holding down the top of the machine down, and prying the entire top of the machine back on its hinge. Then I can get my clothes out. Then doing so in reverse (dont forget to add detergent before shutting the lid! It will lock and you will have to pop the entire top off again.) to use the washer. All because of a 5 cent piece of PLASTIC. What brainchild figured, Eh, we can just use plastic for this important piece that the washer wont run properly without. It doesnt matter!? Someone that wanted to make $300 a pop doing service calls thats who.I cant believe Maytag has gone so far down the tubes. In case anyone else ran into this problem and needs to fix it, write down the model number, serial number, and other crud listed under the lid. Then use them to wipe while youre in the bathroom. All you need is the company and part number on the lid lock mechanism. According to Maytags website my washer doesnt exist. And there was no way, no matter how creatively I googled, to find a part for it with the Maytag model number. So now I have to try to find this measly mechanism to replace and try to use this piece of crud for a few more months. I guess my Christmas present this year is buying a new washer. And you can BET it will not be a Maytag.And two more things: with no agitator, you can fit really big stuff, but you also get to hear your washing machine dancing on your basement floor with an uneven load. No matter how many times you try to re-position items, it runs a corrective cycle, refills with water, and spins everything into a ball AGAIN. Also, the miserable thing is starting to rust. Right on the sides and near the lid hinge, and all around the bleach receptacle. How cheap, a washer on which the paint rusts right off with chlorine bleach.I wish I still had my Grandpas old 1930s wringer Maytag. At least I knew that one would work without a cheap piece of plastic. And at this point I might prefer wringing my clothes to hearing my washer try to escape. In short: cheap parts, no replacements available through company for DIY repairmen, company designed to force customers to use their servicing for $300 a pop. 1/10 would NOT recommend Maytag.

Purchased Maytag washer/dryer in November 2016. Have been dissatisfied ever since. Dryer doesnt dry clothes completely after 90 minutes on high setting. Washer leaves white residue on clothes. Noticeable on dark items. Hardly any water on deep water wash cycle. Bedding just makes a big rolled ball. White powdery residue doesnt come off easily. Rewash, dryer, brushing. Ruining my clothes. Service has been out and they dont appear to know how to correct problem. Maytag doesnt know what problem is and their engineering staff hasnt provided any information on how to fix. Maytag seems very disinterested in helping. They just thank you for being a loyal customer. Not anymore. The attached pictures were taken March 11, 2018.

Its unfortunate that Maytag expects their products to be so short lived, they wont produce parts for their appliances after 7 years. They just told me they are only required by law to make parts for their products for 7 years so thats what they do. So unfortunately, if your microwave outlives its handle, youre going to have to replace the entire appliance which will cost me almost $500. I will never buy another Maytag or Whirlpool products because of this.

The washer is making loud noises. I had a repairman out and he said the transmission was shot. This washer is only 7.5 years old and the set I had before lasted 19 years. It also was a Maytag. My mother, sisters and aunts have always stood by Maytags and I am disappointed that this washer being 7.5 years old is shot. The dryer to the set is working great!

We purchased a washer and dryer, spent in the neighborhood of 1000.00 hard earned $$... extended warranty, the whole enchilada. Maytag. dependable, lonely repair man, ha.. that is just so much stuff. Well anyway it was a Centennial set. What junk. Never really worked that well to begin with. I trashed them both after exhausting all avenues to make it right. Well I got the hair to report the mess to consumer affairs and see if they are what they claim to be. This is more of a warning to all consumers.The stuff you consume today isnt worth the money you pay for it. The money isnt worth the time you spent to earn it. I am gonna try to find a old washer and rebuild it, and a dryer as well. Or just use solar. Best to keep the old stuff repaired and running. I dont know how many people I have spoken to about this problem. Our infrastructure is crumbling. A consumer based economy. Only there is not anyone to service the products we consume... pitiful. I guess my wife will be out back with a tub and washboard before it is all said and done... she will not like it, I guarantee that. I could not even begin to repair the washer. It was a computer operated board that did not work correctly from the beginning. The dude came out from the repair shop and fixed it while still under warranty. It died a slow painful death shortly after that. I disassembled it with a screwdriver and now have potatoes growing in the tub.The dryer has not met the same fate yet. It just sits there, anticipating the moment when I remove it and dissect it with a Sawzall. And I guarantee that day is coming. Do not buy anything from Maytag or its subsidiaries, think long term. We have become a bic lighter economy. I have been on the forefront of that movement. I did not realize it at the time. I do now. and for that I am sorry. I always expect something to work when I need it and if it doesnt, I try to repair it. Cannot fix this stuff now. The support we used to take for granted has been outsourced as well as the production of the product. Bob Dylan said it best in the song union sundown... Thank you and e pluribus unum.

I have had my refrigerator freezer for 2 1/2 years. It worked fine until about 6 months ago. The vent started freezing and then water ran to bottom of freezer and freeze. If I get this fixed, I hope that will be the end of the problem. I am going to defrost it the old fashion way to see if that works. I will never buy this product again.

My washer is new, out of warranty, and about 2 and a half years old. All of a sudden, with no warning or previous issues, the computer board in the washing machine malfunctioned which caused a humming noise, it would not cycle into the next wash phase, the time would go up instead of down, I could not change cycles, and when I would push the power button there would be a delay of power coming on. I unplugged and called my local appliance repair and he said he sees problems with this model regularly, although not always the same issues.Before purchasing I scoured the internet for reviews on different units to make sure I didnt get a lemon. I think Maytag saw the error of their ways quickly and stopped making these before people caught on. This model is no longer being made. I like matching units, so it meant either shell out $500 for replacing the board, or replacing both the washer and the dryer that still works, which would be about $1200 or more for a new set. I chose the least expensive route for now. Not that it matters where I bought mine, but Home Depot and it was on clearance so it was a good price. I have now made up for that difference in repairs.

Our washer sounds like an airplane taking off. Called a repair man and the repairs are $690.00. The washer cost $999.00; such a waste of money. I called Maytag and they say there is nothing they can do. I will NEVER buy a Maytag again.

We had the same problem that everyone is complaining about re: frozen water in bottom of freezer dripping out onto floor. Swore when I got rid of the Maytag smooth top stove that broke after 5 years that I would never get another Maytag but broke down and bought this fridge. Maytag rep made it clear that the Fridge had a NOTE on file about the drain, but it was NOT a product recall. So after virtually taking the freezer apart before the repairman came, we ended up paying $120.00 for the repair, not the part. Yippee. Please note that the repairman told us we saved a lot of money by taking apart the freezer so most repairs probably cost a lot more than ours.

Well Maytag, shame on you! I just called customer service about the third repair made on my Maytag 4000 Series Washing Machine; its only two years old. The rep side stepped the limited warranty that is good for five years on the motor and tried to sell me another warranty for $329.00. I have $460.00 (parts only) in repairs. Purchasing a warranty will have me spending more money than I actually paid for it. The excuse that I was given was (per quote) our machines are made by people and we have no way of determining the outcome of our products past the given warranty. Maybe you should have considered buying the extended warranty that was offered at the time of purchase. Yeah, maybe I should have, but Maytag should build a product that consumers are happy with, and extended warranty sales past a longer period of time might make more sense. If you are thinking about purchasing any Maytag appliance, I would think twice or you just might get some person on the other end of the line that just doesnt care, representing the name of Maytag! I visit the Big Box Stores daily and you can bet your tail that I will make a special visit to the appliance section just to discourage any one from making the same mistake I did! Just think, the last washing machine that I purchased lasted for 9 years (not one issue) and it was still working when I gave it to someone in need! I have three appliances in my kitchen that are 11 years old, never had one problem with either one. Thank You KitchenAid! I should have purchased your washer and dryers!

We bought ALL new Maytag appliances for our home when we rebuilt after it was destroyed by Hurricane Katrina in 2005. We got the top of the line of every appliance. Our Maytag dryer model MDE2706AYW has broke for the 2nd time and cost to repair this time forces me to replace it. The dryer felts, idler pulley and belt went out several weeks ago. Used it about a week and the drum quit turning. The repair tech said the aluminum pulley for the belt on the motor is broke. The pulley is not serviced/available and you have to buy a new motor assembly. This puts repair price on up there where replacing the dryer is the only option. We are going shopping for a new dryer today. It wont be a Maytag.2 years ago, our Maytag washer broke. The repair tech said the transmission went out and it would cost less to replace the washer than to try and repair the Maytag washer. We bought a new washer, different brand. About 3 years ago, we had to have our Maytag dishwasher control panel replaced and 2 months later the pump housing broke. Repair tech said cost more to repair than new. Replaced with different brand.Shortly out of warranty, our Maytag Microwave broke. Everything worked except it would not heat anything. The repair tech said cost more to fix than new. Replaced with different brand. All we have left is the refrigerator which has had 2 expensive repairs done on it and the stove which has had the control board and several heating elements changed. I will never buy another Maytag product.

Owned my Maytag Maxima front loading HE washer for just under 2 years. Went to turn it on one day and got an error code that I later found out meant the computer board went bad (a very costly expense). I called Maytag and explained that a $1200 washing machine should last more than 23 months and if they stand behind their products they should do something to cover this repair. Even after speaking to a manager they told me too bad they couldnt help me. But they would be happy to sell me a $350 extended warranty.... Never again Maytag/Whirlpool!

Maytag washer has increased my water bill; it was supposed to be energy efficient! Also, the washer will not wash a blanket. Sensors will move a large item to one side causing an uneven load which then causes numerous extra fills until stopped manually. I was told to add more items! A blanket barely fits in the tub. I had to invest in lint rollers since the rinse cycle is inefficient. This washing machine is useless. I should have stuck with Kenmore.

Purchased a Maytag Bravos washing machine. DO NOT BUY THIS MACHINE. Disaster as the cycling is hit and miss. The clothes can take 4 hours or more to wash a load. And even then the clothes may still be soaking wet. Grandmas old wringer washer was better. DO NOT BUY MAYTAG. DO NOT BUY MAYTAG BRAVOS.

So far after 5 calls and over two hours spent on calls IMPOSSIBLE to get an answer from Maytag about the correct fill levels of detergent. Consumer support simply do not know and refuse to direct me to anyone or have anyone call that does know answer. WHY SO IMPORTANT? Either you do not get clothes clean OR you damage machine and leave residue on clothes! Neither is acceptable. Using the fill level indicator on Bravos XL dispenser is in direct contradiction to any recommended levels on lids of high efficiency detergent manufacturers like Tide. Per Maytag manual only fill detergent to max fill LINE which is literally about two or three tablespoons of detergent. The lowest possible quantity of Tide per the lines on lid even for smallest load is two or three times the recommended fill level on the dispenser. No one has to be an engineer to know two tablespoons of HE detergent in dispense is going to do same effective cleaning for one shirt or towel as it will with a queen size comforter or very large full capacity load. CORRECT ANSWER DETERMINES IF YOU DAMAGE WASHER OR IF YOU HAVE DIRTY CLOTHES. Googling online there is also no answer. Such a critical answer for Maytag washer to work and clean clothes that is simply not available and documentation is wrong is a huge concern about the viability of this machine and worse their support. Our machine is less than two months old but is obviously over-engineered to the point of just being silly. Tip to Maytag: start selling washboards. More energy efficient, more green except for red and blue bruised knuckles, uses one tenth as much water and users do not need to spend their nest egg savings to buy. Not the first but will be the last Maytag product we will buy. Name may be same but the company is definitely not the company that used to enjoy that name with pride. SUMMARY: Maytag is adamant about using the correct amount of HE detergent OR damage and bad performance by washer and dirty clothes with a detergent residue. With all our best efforts we cannot get what that quantity of detergents is supposed to be. The user manual at best has ambiguous answer. The manual suggest horizontal measure of detergent in tray to max fill level which cannot be right. IF you instead use a vertical measure of how high detergent level comes up to the max fill line the quantity is radically different. It says dispenser holds 3 oz which would be beyond max fill level but nowhere near a vertical fill level.

CONSUMER BEWARE! The Maytag Bravos X is without equal the biggest disappointment I have ever had the frustration of using. What a rip off! Water goes in, water goes out and it makes A LOT of noise. That’s it! (That locking lid should have been our first clue.) Specifically, a normal load takes one hour. What you save in water you pay double for in electricity. If you place a folded pair of pants in the washer that’s the way they come out; folded. Two twin sheets and a small blanket come out of the washer with dry spots every single time. If I use liquid fabric softener the clothes come out spotted with it. And it is louder than the train. You would be 100x better off purchasing a washer at a yard sale for $25 than to throw your money away on the Maytag Bravos X. DON’T DO IT.

Maytag Jetclean EQ Plus Dishwasher - We purchased the dishwasher in June of 2014. Recently the control panel decided it wont work. There is power to the unit. I am told that the unit is no longer in warranty so we have to pay for everything.

I purchased a Maytag washer from Badcock. Within 7 months the control board went out. It was down for nearly 6 months. I had to use a laundromat until I finally rented one from another place. Now again months later the control board is out again (F2F3 Call Service). Due to long wait time luckily I have another warranty but am being told I have to wait 2 weeks before a tech can come look at my washer, and that they wont have a loaner or cant just get me a new washer being the problem is THE SAME! Spent hours on hold only to be told to wait AGAIN! I would NEVER recommend dealing with this company. They used to be top of the line, but clearly not anymore.

I have a 50/50 chance of completing a wash cycle. Most times, the washer stops working at 8 minutes remaining in ANY cycle. The washer will leave me with wet clothing and refuses to spin even when most wet, dripping articles are removed. I have tried to put all light-weight items together and that still is not a guarantee that I can get this done in one cycle. Most often, the error code comes up, I spin the drum around, move the clothing around and try again. This process is NOT energy efficient which is why I bought the ** thing in the first place. I am ready to put it on the curb for the trash man to pick up.We had a service person out and he said it is either the bearings or the motor (both a $400 job). I will NEVER buy another front-loading washing machine. At least with the old-fashioned top loaders you can get the load balanced and at least get clothing to go through the spin cycle. I am now hand-wringing clothing once again since the machine tells me when it will spin my clothing. That stupid chime is about to send me out of my mind!

Purchased top of the line Gemini oven a few years ago. Lower oven stopped working. Maytag repair said igniter not installed properly at factory. I contact Maytag customer service to see if they would help with repair cost. Rude response from them... basically saying anything fails after 12 months not our fault. Rejected my request without even asking details about product which model etc. Unilateral rejection. Horrible customer service. I will never purchase Maytag appliance again. Horrible, horrible, horrible. Avoid this company and their products. They do not a good product and they provide terrible customer service.

Maytag Bravos XL Washer and Dryer. How exciting to get a new washer/dryer!! Im a savvy bargain and quality shopper, but I really messed up here. A little over a year ago, we moved from IL back to TX and I got to buy a new washer AND dryer at the same time (a rarity). I went and looked at SO many washers/dryers and decided on the Maytag Bravos XL because a friend said she loved hers. It had a deep water wash and bedding cycle (for our blankets, comforters, sleeping bags, etc), and I thought that I could throw that wayward sock in after I started the load (unlike our previous front load washer).Where do I begin with the complaints? (And Im NOT a complainer - never filled out a review in my life). This is what I sent to Maytag: 1) Im 55 tall and can barely reach the items at the bottom of the drum, along with the lid falling on my head when Im trying to do so. 2) Forget throwing in the wayward sock - it must finish the cycle its in before it will let you unlock the lid (Where did locked lids come from anyway? Is that how those missing socks are disappearing - escaping out of unlocked lids? What are we trying to keep in or who are we trying to keep out of the machine? Doors you lock - not washing machines! I dont get it!).3) Even the deep water/bedding wash cycle does not do the job. Using the exact recommended measurement of HE liquid soap does not get the items clean. What a chore to take something out and have white detergent lines all over it and have to wipe it down with a wet cloth. Sure, I could then do a rinse and spin cycle, but since it doesnt add enough water, it doesnt come out much better. The machine senses by weight how much water to use. I am positive that every energy efficient machine is now programmed to add exactly 4 cups of water per load (regardless if its a comforter or one pair of jeans).4) Supposedly, we are saving so much water usage, but energy efficient is a misnomer - it takes me twice as long to do laundry now. The time factors are ridiculous. There are no quick cycles on this machine. If I have a load of delicate tops that just need a quick wash and rinse before I hang them out (I was not out baling hay in them, so its not like they are filthy dirty. In Texas, its the sweat that you are trying to eliminate), the least amount of time I can find on a cycle is 45 minutes. I might as well hand wash them all and be done in 5 minutes. But, that was the point of the washing machine - to do the work for me! And forget the deep water wash cycle of 58 minutes, plus the added rinse and spin cycle (to try and remove the white soap line). Its now taken one and one-half hours to try and clean/refresh a barely soiled comforter.5) The spin cycle is SO efficient, that I have items come out totally dry many times in certain spots. Im washing a comforter right now and I can guarantee you that when I remove it from the washer, there will be an entire section that looks like it never even got wet. Im no engineer, but after watching through the see-through lid, the agitation is not working well enough to get to every section.6) I havent seen a soap bubble or suds yet. You are told to use such a small amount of detergent, Im not sure how anything actually gets clean. The clothes are sprinkled with water, agitated a small amount, spun until they are almost dry and voila - the same dirty clothes come out! 7) The dryer has now ruined 2 of my bras as the hooks get caught in the mesh panel at the back. It literally melted part of the bra! I tried hooking them together before I threw them in there, but now have to put them in a lingerie bag to keep them from being mauled and mutilated. I have NEVER in 37 years of marriage and washing had that happen before.8) I literally could not get my dryer to turn on and a repairman had to come out to the house to show me the amount of pressure I had to use in one finger to start the dryer. I had almost taken a hammer to it before he arrived. Can you imagine pressing the start button on anything - the dishwasher, a hair dryer, a TV remote control, and it not turning on? And all because you pressed too hard or too light? This computer age and electronic panels are killing me! 9) The dryer has the same locking system as the washing machine. So, if you didnt see the wayward sock on the floor or between the two units until after you pushed (lightly, of course) the start button, you have to stop the unit before you can open the door to throw the sock in.I didnt mean to write a novel (about a washer and dryer, no less)! But, I feel better and hope that I have saved one woman from making the same mistake I did. Read those reviews AND believe them. And by the way, my friend who recommended the Bravos XL to me looked at mine and said Thats NOT my washer and dryer. Evidently, mine was the new and improved version! So much for that claim!

This is the absolutely worse washer I have ever owned! My clothes actually come out dirtier after they are washed. It leaves white stains on clothes that I have to scrub out by hand. Maytag you should be ashamed of yourselves for coming out with a washer like this. It takes me 2 or 3 times to wash clothes and I have to use the power wash, extra rinse, and maximum clean setting to even come close to cleaning. It is cheaper to take my clothes to the dry cleaner now than use the washer. I called Maytag numerous times, and they said that they will charge for a service call unless there is actually a mechanical issues. They will not honor repairing the machine if it does not wash clean. I will definitely NOT recommend this washer.

We have a Maytag drying center that is almost 6 years old. It never did a good job drying especially for the money we paid, but it just quit on us two weeks ago. We purchased it from TA Appliances in Barrie, Ontario who recommended that we call B&K Appliance repair to fix it. The owner showed up and said he would be back to us in a few days to fix it, as soon as part arrives. He now wont return calls and it has been two weeks, so we called Maytag customer service. We knew we were in trouble when we received a message telling us Due to higher than normal call volume... (so much for the Maytags that never need repair). Anyway, we finally reached an incompetent, ignorant and anti-customer service representative who proceeded to tell us in an extremely, nasally drawl that the part needed to fix our 6 years old dryer is no longer available and the most they could offer as compensation for this on our $1500 plus tax dryer that should last at least 10 years is $120. This is for a dryer we never used more than 5 times a week.

I bought a Maytag dishwasher (model MDBH945AWB3) in March 27, 2010 to replace a Kitchen Aid dishwasher that was only six years old and no longer serviceable. After a little over a year, its dead. When I try to turn it on, nothing happens. If I press the delay button, the lights come on, but in about a minute, they go off.

Bought DW 2 1/2 years ago. The control panel has a mind of its own, and today it will not even light up. How does a recall happen? I see lots of people having trouble with this model and others as well. A dishwasher should last much longer! Will never buy a Maytag again... and will recommend the same to my friends.

My husband bought me a Maytag washer as a surprise gift. I was so excited to get a Maytag. I will never purchase a Maytag again. I am so tired of washing, rewashing and rerinsing my clothes and still not getting the soap out. I have used every different kind of detergent and used with and without fabric softener. I have also tried cold, warm and hot water. I would rather use more water and get the soap out instead of using more electricity to keep rewashing my clothes and then in the end having to take a wet cloth to get the soap out. Never had to do this with any other washer I owned. Very disappointed as I always thought Maytag was the best.

2011 model MVWC2oox W1- spin dry failure - We purchased above top loader in 2011 and have had no issues until now. Currently constant failures on spinning and drying. Spin cycle stops without getting up to speed and appears to be an unbalanced load sensor problem. Also draining is not completed (possible pump going bad). Area tech came out within a week as promise and ran the diagnostics and found no faults. Problem has continued. We do a load a week. Looking for better answers or a new washer.

The new Maytag commercial brand is different than the traditional Maytags. Uses less water. The new technology in the variety of choices for cycles and the steam cleaning for the dryer is a great feature.

The control panel of our Maytag dishwasher stopped working when it was approximately 14 months old. We repaired it ourselves by following a reset directions we found online (push rinse button 5 times and then the cancel button twice). Also we cut the power to reset. Im not sure which of those two tasks reset it, but it worked until last week - now 28 months old. We are not able to reset the panel using any information that we can find. In trying to find repair options, we discover that there are a lot of complaints about the Maytag dishwashers control panels not working within just a couple of years. In speaking with Maytag, they tell me theres a class action law suit for this problem - meaning they do realize there is an obvious problem with their control panels, but are not acknowledging they have any responsibility to repair it. The law suit only covers the cost of the part but not the labor. The labor can cost between $100 - at the lowest - and up. Our Maytag dishwasher model # is MDB8949SAM1. Also noteworthy, our Maytag clothes washer gave out at less than 5 years. Maytag is no longer the company we all thought they were. Additionally, their faulty machines are costing their customers a lot of extra money. Not exactly what I would call a company with good customer service or even any ethics. We will never buy Maytag again.

Purchased Maytag dishwasher model # MDBH979SAM1 on February 8, 2014. 6 months in paint came off door. Added 5 year extended warranty on 4/21/2015. Dishwasher started not working properly on 9/24/2015. Hit one button but a different would light up until finally on 10/2/2015 it quit working. Called for service On 10/2/2015 10:30 pm no answer. Tried again on 10/3/15 same answer. Tried again on 10-5-15 finally answered and they called repairman. No answer but they gave me his number so I could call him if he didnt call. Finally called him and He told me he was busy and could not come repair my dishwasher. I called MaytagNed they said he would come. When I called he said he was not coming. He had truck trouble. 10-12-15 Called Maytag back and they said they would find another repairman. They would call me back. Into 2 weeks waiting on appointment. I will never buy Maytag again. It didnt clean dishes good when it did work!

Bravos MCT maytag commercial technology washer - Bought this washer a year ago. Will not complete cycles. Will not agitate. Never buy Maytag.

Maytag Bravos Quiet Series 300 - Our motherboard on the washer went out after 2 years from purchase - just out of warranty. Motherboard was $550 so we bought a Samsung. Now our dryer has gone out for the second time. First time was the pulley assembly came apart. We self-repaired after watching YouTube. Now the motherboard has gone out on the dryer! I will NEVER buy another Maytag product. They are a waste of hard-earned money and have left me with piles of laundry numerous times. Maytag, you need a class action suit filed against you!

The Bravos XL MCT Maytag commercial Technology is not a good machine. I noticed it within the first few weeks. I called Conns to request technical support but the technician they sent didnt solve the problem. I also called Maytag, they also sent a technician. He told me the same thing as the other guy. To use good quality detergent and to make sure the clothes are neatly arrange around the drums walls. Nothing works. My clothes dont get clean because they dont get wet. Theres lots of residuals and wrinkles all over them. Also, the machine takes way too long to finish a load of clothes. I did tried to return it, but Conns wouldnt take it back. I dont recommend this washing machine at all!

Well I must say I concur with all previous posts. I just replaced my Bravos with a Samsung after my jet plane of a washer died. My repair guy said it was not worth it to fix it. I had already replaced the shocks two years ago but I did have mine for 8 years. I have had the same problems as previous posts - rust, smell, holes, broken, too expensive! Hello to Samsung!!

I will never buy another energy efficient washer again. My Bravos is supposed to save money and be environment friendly, but when you have to wash clothes more than once to get them clean, theres no savings. Ive tried different detergents, cleaned the washer, rinsed twice, added vinegar, baking soda and everything imaginable to get the clothes smelling fresh without any luck. I have had several items ruined because the bleach dispenser pours onto dry laundry. Im disgusted.

Like so many other consumers, I was drawn to the Maytag name because of what I thought was the high quality of their products and their stellar reputation. So when our old wall-mount oven failed, I sought out a replacement from the Maytag line. I purchased a model MEW5530WDDB17 in 2011 and had it professionally installed. It worked well for a couple of years. Then, suddenly, three of the numbers on the digital control panel stopped working, making it impossible to set the oven to any temperature that included a 4, a 2 or a 5. When I contacted Maytag, I was informed that the unit was out of warranty, but that I could schedule a service call. I had already researched this issue online and knew that the service person would inform me that I needed a new control board and that one could be installed for around $300, and that the new board would come with a 90 day warranty. When I asked the person to whom I was speaking, she said that she had no further information for me. I know that a lot of others have had this same issue with their Maytag range/ovens, and many of them agree with me that we will never purchase another Maytag product.

Maytag model MBF1958XEQ1 frost build up and ice build up bottom freezer 2011 model. Recently refrigerator not able to stay cold. Contacted Associated Service Corp. because my fridge had a ten year warranty on the compressor only. It cost me $377 dollars to have a service tech change the circuit board and remove a rubber drain valve that was blocking the excess water drain to the evaporator tray. It is working well now but will keep looking for ice build up.

I own my oven for 10 years. It still looks brand new. The bottom oven went out and they do not sell the replacement parts anymore. I think its terrible that I had to go and buy a new oven when mine still looks brand new.

MDB77495852 - I purchased a brand new Maytag dishwasher 2 years ago from Sears. A year later it broke down with what was apparent moisture in the control panel. Thankfully it was covered under warranty. Well guess what... it broke down again a year later and now just missed a year. But not it matters, the retailer (Sears) said it was not covered so Im supposed to pay about $300.00 to get it repaired. And figure I will have to do so next year also. I was told there is a Lemon Law for appliances but it does not kick in for 4 years. So after $900 in repairs I could get a replacement... REALLY? I think a recall is in order!

I bought the Maytag washer and it lasted 5 1/2 months. I am now going on 1 month without the washer because no one wants to take responsibility for it. Your warranty and service is crap. I will never buy another Maytag product and I will be sure and let anyone that I know that is about to purchase one not to!

I am happy with this dishwasher. I had a GE that had a lot of problems. I insisted on getting Maytag and I have been happy ever since. It controls the time, temperature, and is easy to operate. I would like a bigger dishwasher because of my family size. This dish is okay for a family of 4. It matches my furniture. It blends in. No complaints. The digital pad is convenient but it has been fixed a few times. I had a few technicians who did not know how to fix. It was not the dishwasher, it was the technicians.

I bought my first centennial washer less than four years ago, warrantied that machine out. It was replaced by best buy because of the warranty that I purchased. We are a family of four, with that in mind the replacement machine was a model year newer and it last just over a year and quit. I bought the machine anticipating that it will last me the next 10 years. With two children at home now that is not working, all I have to do on replace a new machine. The repair shop has told me that they get more of the Maytag centennial machines and then any other washing machine is going to cost me more to repair it than to buy a new machine because I had faith in the Maytag products for many many years. This particular machines are extremely hard to diagnose as to what causes the problem or what the problem is and could take a long time to get it fixed as well as the expense of getting it fixed. I would not recommend another Maytag product nor will Maytag ever get any more money from us. This particular product has become a piece of junk that I cant even get rid of to recycling. Maytag has become a joke and this machine has become a 500 dollar hunk of junk in my opinion.

Bought a Maytag MVWX655DW top loader clothes washer from Best Buy on 7-7-2020 it was delivered as promised on Friday 7-10-2020. The people who delivered it were very professional and nice. They did a great job installing it. My wife went to use it for the first time Saturday morning 7-11-2020. Luckily this washer had a see through door. We could not believe our eyes, it never put enough water in the tub to cover the clothes. So as we watched the clothes on top never participated in the wash, they just moved around. When it went to spin cycle it was making a loud clicking sound as it was shaking. So we tried different settings, after 3 loads I called BB and said I want to return it. This machine has been mislabeled, its not a clothes washer, its a noise maker at best. DO NOT BUY THIS MACHINE. IT DOESNT WASH CLOTHES.

Maytag msd2650kes refrigerator - I replaced compressor switch three times then compressor went out after only almost four years. We bought all new Maytag when remodeling. Never again will we ever be that stupid again.

I purchased the Maytag Neptune set in 2004 and was not informed there was a class action lawsuit and was never notified. When washer quit working, I called Maytag who sold me a $300 service contract. They came out and said they couldnt fix the washer and I needed to buy a new one. I paid a fortune for this piece of junk and now have to spend another $700 to get a new washer. I will never buy Maytag again. How can they get away with selling washers that are on recall and involved in a lawsuit?

Bought a nice looking Maytag fridge 2 years ago. For the past 6 months it has been leaking all over the kitchen floor. Most recently it has started leaking every 2 days. It is so frustrating as well as extremely dangerous! Both my younger kids have slipped and fell because of the slippery floor. We now have to keep a towel there all the time.Please let me know if there is a product recall. Not the Maytag we used to have. My parents bought all their Maytag appliances when they got married and they lasted over 30 years! This is why I bought the Maytag fridge... not sure of the quality now.

Does a good job of cleaning but takes much longer to complete. Pretty much standard features. Has rinse only cycle, air dry only cycle, and cycle for pots and pans. Top rack had special holders for long stemmed glasses which I dont need. Standard size. Same size as my Kitchen Aid. White, front load, no special appearance. It takes much longer than my old dishwasher. Also the soap dispenser broke after 2 months and had to be replaced. It requires that two buttons have to be pushed to start. My old one only required one. It does a good job of cleaning.

I too am a victim of the faulty Control Panel that Maytag put on these dishwashers - Model # MDB7749SBM2. $149 for the part and another $149 for service call and labor - almost half the price of what I paid 2 years ago! Should have stuck with the 10 year old builder grade GE I had with the latch door and turn knob! I am in the market for a new stove and microwave - I will never buy another Maytag or Whirlpool product! When is Maytag going to make good to all the customers out there that have experienced the same issue? If yours breaks it is a very easy fix now that I know. You can order the part and it simply unplugs and plugs in the new one. All you have to do is take the door off and it is right there!

The washer 4 years ago we had the control panel replaced at our expense. Now, control panel is going out again. Also this summer I took the dryer apart to snug up some screws that had come lose, that were scraping the inside as the dry ran. I own a range and a dishwasher Maytag brand but will not buy another Maytag unit, even if they are built by my union brothers and sisters.

We bought this washer in 2009. It has only been 5 years and we had a problem with the lid, now it leaks on the floor and most of all it has been rusting on the lid, the sides and rusting around the bleach port. Rusting on the top edge of the outside metal skin. I am not happy with this product at all. The serial number CV0870202. Model number is MVWB800VQZ. It is a quiet series purchased on 2009. I am not happy with the quality of this washer and I will not buy another Maytag.

I was always impressed with the front loading spin washers commonly found in laundromats. The top loading Maytag Bravos does a great job of cleaning clothes and does not stick another door in your way when loading or unloading it.

Dryer delivered nonfunctional. Tech showed up the following Tuesday. Diagnosis main board and one sensor dead. Tech returns following Thursday. Replacement board DOA. New dryer still nonfunctional. Awaiting new board with no functional $1100 dryer. This dryer replaced my three year old Maximus which was deemed too expensive to repair after three repairs. Please do not buy a Maytag/Whirlpool product.

This is the loudest washing machine Ive ever had!!! I ask the installer if it was suppose to be so loud & he said yes. The machines sounds like metal scraping metal when its washing the clothes.