Im so mad over my new purchase on the XL Bravo washer and dryer and Home Depot will not return. I have 3 kids and a hard working husband. My clothes do not come out clean no matter what cycle I use. It takes forever just to wash one load. If you spill something on your clothes and it dries crusty it will come out of the washer crusty. I want to cry. So much money wasted and cant get our money back. Would never recommend a washer without an agitator. Towels come out soaking wet, and dont spin dry if heavy...forget washing a blanket. 4th day using the dryer and now there is no heat. What was I thinking!! So mad and sad too!

Purchased a Maytag Atlantis washer at Lowes in 2004. Until recently it worked without any problems; however, the agitator never seemed to work quite right. Normally, an agitator rotates in such a way that the auger action of the vanes pulls the clothes in toward the middle and then down into the water such that you have a continuous cycle of clothing being pulled down the middle, agitated at the bottom, then pushed up the outside. This one agitated but the clothing would just go round and round in the tub. Everything managed to get clean enough, but clearly something was amiss. Recently, the spin cycle became loud. A rumble became a loud roar over the course of a few cycles. Then I noticed water on the floor coming from under the washer. The short story is that the center shaft seals had just worn out. After almost 12 years of use, thats not surprising. Whats surprising is that it had worked so long without any issues other than the agitator.I took it apart and, to my dismay, the water had gotten into everything so that some of the metal parts were hard to remove. After having determined what replacement parts were necessary, I ordered them, but then placed additional orders for parts that probably would wear out eventually. So I ended up doing a near-complete rebuild. Other than the difficulty of taking some of the parts apart, and removing/installing the tub springs, it was actually pretty easy. I have reassembled, and now it seems to work flawlessly... so far. About the agitator: I found that shims are used on the transmission shaft to adjust tension. Too much tension and the clothes just ride around the tub; like mine did. Too little tension probably results in the thing not agitating at all (I dont really know). Once the washer is apart its easy to set the tension (insert the shim washers) correctly.There is a clip that holds the shim washers in place on the shaft. It was really tight; somewhat difficult to remove. One of the shims wouldnt fit when I tried to reassemble. As it turned out, that was a good thing. My research on this model revealed the way to get the proper tension. My assessment is that whoever assembled this washer at Maytag (or whoever builds these) assembled it incorrectly! Another thing I found out - after I ordered/received parts, unfortunately - is that there are two types of tub/shaft seal sets for this washer. I ended up replacing the newer type seals with the older type. Everything fits, but I may be losing out on a newer, better design. Well see. Overall, I am very pleased and impressed with the longevity and reliability of the MAV9501EWW washer. I have had Kenmore and Whirlpool; neither of which was nearly as durable and reliable. I hope this is helpful to someone.

We bought this washing machine 2 years ago and I was never really satisfied with how it cleaned the clothes. Darker pants would come out with white soap/water lines on them. The worst part, 2 years in, the washer basket seal failed and the bearings rusted. The washer sounds like a tornado every time it runs. I got a quote for $350 to repair it!

It meets all of my needs and expectations. Its quiet looks nice and does a very good job of cleaning dishes.

I have had nothing but headaches with our washer. We purchased it 4 years ago and after using it for a few months, I took it out because our clothes came out smelly and unclean. Called Maytag and they did nothing. So we went back to a regular washing machine and put this machine in the corner of the basement. I refused to throw away a $1,100.00 machine! So this year our machine quit, so we decided to try using the machine again to save us some money instead of buying another one... Well, that lasted for only a short time. Clothes still smell, came out unclean and just yesterday, the machine stopped rinsing and spinning! This machine has barely been used and its been nothing but trouble. Maytag service just plain sucks. They dont care about their consumers. I will never buy a Maytag again and I always let everyone I know to not buy this type of machine.

Maytag French door Bottom Mount Model # MFT2976AEW02 - Purchased this model refrigerator in late 2013. Had minor problems with ice maker for last 6 months, not have freezer problems, as the bottom freezer is not keeping food frozen. Called repairman today. He ran 64 checks on refrigerator, said to keep eye on problem and he will re check in 24 hours. Called private company, Maytag in Latrobe. They referred us to the Maytag repairman. We will keep you posted. We moved all of our frozen food to a downstairs older freezer for safekeeping. Keep checking, we will update.

I spent a lot of money for top-of-the-line Maytag. It sanitized and worked to perfection. Delay wash, force wash, grinds everything you could possibly ever want. Fantastic and I can move the racks around. Beautiful. Stainless steel tub. Stainless outside. It has a ribbon cord in the controller. They didnt seal the controller head enough. So the dishwasher stops working after an almost guaranteed 2 yards from the ribbon cord rusting. Well you got to buy another one and it comes as a fill unit at 250 IF you replace it yourself. About 500 for a plumber. And you replace it every 2 years. Maytag is having class actions about it, it knew it has the problem. Its just very profitable to continue having the problem.

French Door Maytag MFI2569VEW10 faulty in many ways. We bought our refrigerator 7 years ago. After 2 years the freezer door handle fell off; after 4 years the right front door gasket began to tear (normal usage); after 7 years, it no longer dispenses ice or water. We now have mildew/mold growing around the edges of the door because there is no longer a good seal. Constant cleaning. Additionally, we are spending more $ to keep the refrigerator at the proper temperature because the seal is broken. To repair these items is almost $700 including shipping and tax. This does not include the cost of labor. So after 7 short years, we have a hunk of junk that does not work properly. I am shocked that Maytag sells such an inferior product and we are left holding the bag. Do not buy Maytag. Additionally, our Maytag microwave broke after 5 years. DO NOT BUY!!! Buyer beware!

On May 11, 2010, I purchased a Maytag washing machine from Lowes. On June 22, 2011, the machine wouldnt empty out on the rinse cycle. Lowes was called as the machine was only one month out of warranty. They dispatched Appliance Plus for a service call which would be $80.00 just to diagnose the problem. It turns out the machine needs three parts - a timer, an ATC switch, and a rinse switch. All totaled, this will add up to over $300.00, plus the $80.00 for the service call.Appliance Plus tried to contact Whirlpool to see if Whirlpool would at least pay for parts, being it was only one month out of warranty. The answer took 5 days and the request was denied. I was told I should contact Lowes Service Advantage and maybe they could contact Whirlpool for a special consideration, again, being it was only one month out of warranty. I made the call and they said to give them two business days turn-around for an answer. On June 30th, Lowes said Whirlpool was looking for the serial number and I provided it. They told me to give them another 2 business days turn-around. On July 3rd, I again called Lowes and they informed me that they still hadnt heard from Whirlpool. Finally, on July 7th, I received a call from Lowes saying Whirlpool denied the request.

I purchased a new Maytag dishwasher model MDB7609AWB1 approximately 2yrs ago from Sears. We purchased quite a few new appliances from them and they are always helpful. Within the first year, right after the warranty was up, it stopped working. No lights on the power panel. I called Sears, out of warranty, sorry. Said they would give me a deal on the repair. Sears came out, replaced the computer. $230.00. 6 months later, it stops working again. I go on line to look up these models and sure enough a lot of people are having the same issues. I did some of the checks that they said to do and found my plastic door latch was broken. A little plastic arm that actuates the switches broke. Should have been made of metal. I replace it myself, very easy, by the way. So I figure, in another 8 months it will prob break again. They run anywhere from $19.00-$30.00. 2 days ago power panel and light, not working again. I called Sears and asked them if they were having issues with the power panels that this was the second time in less than 2 years, and if there were any recalls, they said no. I guess they dont follow their reviews, but according to google reviews, its a major problem with most of them. Maytag, Whirlpool, and Amanda. Ordered a new panel today, again they are $141 from Sears but if you shop, you can get a new one for less than $85.00. If you have any kind of mechanical skills, you can replace it in less than 20 mins. It just seems to me that this big companies have let their quality control go and are more concerned about the profit. There should be a recall on these. Do Not buy a Maytag/Whirlpool dishwasher, they are total junk. Sorry Maytag, you lost another customer.

A refrigerator has to keep your food at constant temperature. The first Maytag refrigerator I purchased from Home Depot could not get cold. I mean the refrigerator never got below 65 degrees. I called Maytag and they played dumb. Just wait weeks for a repairman to check a brand new product that is not working. Home Depot replaced it in few days with another refrigerator of the same model. It runs but doesnt get really cold (it only has a fan in the freezer and the air comes down from the freezer to cool the refrigerator). I live with it because all you will get out of Maytag/Whirlpool is to turn the dial to a colder temp. A little over a year passes and the fan in the freezer just stops running. I called a local certified service person. He looks at the fan and says that its running but barely. I had to replace the motor at cost with labor of around 200 dollars. I kept the motor. Turns out the motor is made by Panasonic. The current replacement motor is made in Mexico. Now the refrigerator runs cold. Since I had two of these refrigerators that failed to get/stay cold, I think they got a bad batch of motors. Maytag response was to refuse to pay a dime, it is outside of the warranty - even though I had called about the refrigerator not getting real cold on the second refrigerator. So basically I lived with food being kept at a way too high of temp causing spoilage for a year and Maytag/Whirlpool could care less, they are only worried about their bottom line.That is not the only problem with their product. The drain pan grows a mold that looks like pudding. The only way to clean it is to pull the refrigerator out, take off the motor area cover (which is really cheap cardboard) and clean it out with a rag. There is no way to remove the pan. The compressor is mounted so low that it heats up the floor. I have concrete floors thus I have no fire risk but if you have wood floors, I would check the heat level. It is nearly impossible to clean the dust off the fins on the refrigerator coolant lines. The back of the freezer door shelves are metal and very sharp on the back. Thus if you stick your hand in to pick something up, you will get a nasty cut.I have owned only Maytag, Whirlpool and Amana products my entire life. I will never purchase their products again. They may pretend that you are buying an American product (they use the American flag) but this product is nothing but OEM garbage made by the lowest bidder. They try to sell you an extended warranty for around 300 bucks for an addition 3 years. I figured if the fridge went bad after 3 years, I would just buy a new one. I never expected a motor to fail less than a year (I would say it started going bad about 6 months into ownership as started making ice at a lower rate). Maytag refuses to stand behind their products. When I told them I had the motor that failed, they had no interest in even looking at it. Do not waste your money on their products. I also own a Maytag washer that is the worst washer I have ever owned.

Maytag Microwave MMV4205DW-1 - This microwave made it one year and one month before the door would no longer latch shut and the control panel stopped working altogether. Called Maytag and was told not under warranty. It was going to cost more to repair than to purchase a new microwave that was a different brand.

Bravos X high efficiency... efficient at not cleaning your clothes, efficient at ruining clothes, sheets, towels, may be efficient at being a boat anchor. Maytag offers nothing. Have had washers last 20 years or more. Someone, or some atty. General should bring a class action suit. Horrible product. Dont buy one. DONT BUY MAYTAG/WHIRLPOOL. THEY DONT TAKE CARE OF THEIR CUSTOMERS. JUNK. That report was very fair as requested. You really dont want to know how I really feel.

Back a couple years ago, Dec. 29, 1983, I purchased a Maytag washer, model A209, and a Maytag Dryer, model DG110. Im still using them daily. The washer has given NO problems, other than the brake has taken to squealing. This causes nothing more than a notice that the load is done, so no repair is necessary. The dryer has proven more problematic, as I have had to replace the ignitor three times, the blower fan twice, and the motor (and belt) once. I still think I have gotten my moneys worth.

If I want to line dry something, first I have to pick off all the lint. Even when I use the dryer, I still have to pick off lint and there’s often creases with dirt dried right in. I have to inspect everything that comes out of the washer to see if it is clean before I dry it. This doesn’t save water, as I often have to wash things at least twice. Awful! Also, ridiculous. A wash machine is supposed to get things clean.

I purchased a Maytag microwave oven on July 22, 2011. It was delivered August 2. Model no. MMV4203DW, serial no. CK01001086. I paid $279 at Lowes Spokane Valley WA. I made a family brand name dinner for six in the original black carton, put the rack into the microwave, followed all the directions as the microwave was new. The carton melted inside and burned a place where the rack had rested. This melted before the time was up. I had followed all the directions. This was the first incident that was a problem. Next incident was a large bag of popcorn (microwave has two settings for popcorn--large or small). This burned the bag black before the allowed automatic setting. Third incident was another bag of popcorn, which resulted to a fire. I tried putting it out with a large lid, which now has permanent black smoke stains. The fire was so hot I could not remove the popcorn bag. I had to use two pancake spatulas to throw it outside where it continued to have flames and burned itself out. The next fire was with a baked potato. This was set for a regular potato setting. This fire was great flames. I tried putting this out with salt and a pan lid. I also removed it with a large metal strainer, an Asian type which is large, and used another spatula to scoop the flaming potato and took it outside while it continued to burn. This time the microwave burned itself out. All lights would not function so I unplugged it from the outlet. I have repeatedly told Ava that I had previously owned a Kenmore convection microwave and the only time I used the rack was when I baked something. She continued to ignore this and said that I used the rack to make popcorn, baked potato, etc.

We purchased our washer Model # MHWE450WW01 and Serial # CS10502122 on March 30, 2011 along with a front loaded dryer and refrigerator on March 30, 2011 from a local store Appliance Outlet in Duncansville, PA. As with most new purchases we were excited as all three of these appliances being replaced were 20 years old. All were installed and worked great. My wife and I would often comment that in the spin cycle the washer sounded like a jet engine readying for take off. At some time in early 2014 we had Appliance Outlet come out and inspect the washer and told us that the washer was not to be that noisy and they would authorize replacement parts under warranty. In calling Maytag we were treated well and the parts came. Rear tub W10772619, Basket W10283352, Front tub W102823352.One of the parts was in fact cracked when it came in and had to be reordered. It was and several weeks later it arrived and Appliance Outlet fixed the washer. It ran so quiet we could not believe it was the same machine. In late spring of this year the noise was back. Appliance Outlet confirmed that indeed the same issue was happening and we would need to replace the parts again. In early June 2105 I called customer service and explained the situation and the rep took the notes and stated that we could indeed get these parts replaced and we as homeowners would pay for the labor. As YOU would I tried to get the labor paid for and was given the company line policy and told that there was NO way Maytag paid for the labor and the parts would be shipped. I accepted these terms.Yesterday my wife called to find out the status of the parts shipment and was taken for all intent and purpose right back thru the initial call routine. NO record of my call in early June existed and the best she got was that if Appliance Outlet would call and order the parts that they would be reimbursed. Appliance Outlet said that is NOT normal warranty procedure. Normal warranty goes from Maytag to the appliance Owner. They only confirm the issues/problems and do the labor. I am now stuck. I am also CEO of a company and while it pales in size the buck stops at my desk.

We purchase a matching Maytag washer and dryer set and within the first three months our washer began to give us error codes and would not wash our clothes completely on any cycle. It was repaired and we began to have the same issues within the next couple of months. This all happened within the first year. We called customer service about extending our service warranty due to the multiple malfunctions of this washer. We were given the run around and, quite frankly, the attitude that this was not their problem. I WILL NOT BUY ANOTHER MAYTAG PRODUCT! Thank you customer service for ensuring that I will not be a repeat customer!

I have had nothing except trouble with my new Maytag Bravos washer! I first had a suspension arm or something like that replaced along with the agitator. My water cycle has never worked correctly since it was new. I take out the clothes and half are still dry. My daughter washed her kids’ clothes in the washer while she was living with us and the stains did not come out. She thought that is really unusual since they werent stains that normally you would see left on the clothes. I went to my father-in-law’s house (they have a front loading Bosch), took her detergent with her that she used here and guess what? It’s just one washing and the stain was gone. She had washed the clothes in our washer at least 7 times trying to get out the stain. Now, we have such a loud noise that it sounds like it is going to take off. Then, the bottom of the washer started to leak. We took it out and checked it and we cant find the leak. The clothes smell awful when they come out of the wash. I dont know if it is bacteria build up. I use the cycle cleaner when I am supposed to. This is so sad. This is the first time I have had matching washer and dryer and I wish I would have kept my old Sears model that worked great. I havent decided if we want to fix it. With the price to fix it, I can buy one I might like. Never will I buy Maytag again or another Whirlpool without checking out the reports.

The Maytag range was purchased locally in 2012. The racks kept falling as the oven cavity warped in a convex making the rack supports too wide. The racks fell at the best position to cook a turkey. This could be dangerous when lifting something like a turkey or pie with filling! I was told that the oven cavity is NOT replaceable and I needed to purchase a new range! $1,600.00 plus taxes were spent just three years ago and now Im being told it cannot be repaired, no parts are available and needs to be replaced! Im sorry but I feel cheated and hurt because Maytag will not give any concession despite my pleading. What a dirty way to conduct business! No concession except an offer to cancel the service charges so far if I replaced it with another Maytag range from Delhi Radio Ltd. Are you serious?Why cant wider racks be provided for in these cases? Just what kind of engineer would compromise the thickness of a ranges oven cavity? Then build the range in such manner that the defective part is not available and cannot be replaced? Its a sad day for Maytag! Shame on you! Ive seen Maytag washers built in Newton last 35 years of hard family type washes! Whirlpool has purchased the name, stamped their own products with the Maytag name, and rested on the fine reputation of the name brand. Everything else is different! The Newton plant is in mothballs leaving hundreds of proud faithful employees stranded. Its a sad day for me and many others who were duped by a brand name and got something completely different.

Maytag Bravos Series 300 - I bought this machine less than a year ago. There is an awful smell coming from the machine that I never smelled from any other washer I have owned. The clothes do not look, feel or smell clean, and my towels are ripped. It is an extra large washer, yet when blankets are put in the machine bounces and shifts. After reading all the reviews, it seems I am not alone in my concern with a machine that was not only expensive, but was told it is a great product. Maytag needs to do the right thing and recall this machine.

Bought va washer. Trying to upgrade. Water fills about 1/3 of way even on bulky setting. Supposed to be high efficiency. Detergent does not get all the way out because there is no enough water. Have to put it through 2 rinse cycles. Worst machine. Design is flawed. Clothes all wrinkled. I cant afford to buy clothes and have them ruined. Man must have designed. Hate the washer. Im poor and they want take it back... want my money back. I cant buy washer every day. I will keep on complaining. No customer service. People just put you off. It is a Centennial high efficiency. A piece of junk.

Clothes are never submerged in water. Clothes come out worse than when they went in. Every review and complaint mentioned is dead on! This Bravos XL is a piece of crap. Stay away from lying salesmen from HH Gregg. And stay away from Maytag. Perhaps we should all get together and file a class action lawsuit! And donate all monies, washing machines and dingy clothes to charity!

Purchased new about 3 years ago, doesnt clean, ties clothes in knots, leaves white spots from softener that doesnt get wet sometimes after cycle, some areas are still dry after untying. Now error code 51 keeps appearing, service man 4 times replaced rps sensor as directed, nothing changes. Need a chain to drag behind truck, no technical support from Maytag or whirlpool. Old ones of 20 years still worked good, gave to niece. Lucky her.

We bought the Bravo washer and dryer in 10/2009. Since then the dryer has never worked well. Weve had at least 8 service calls on same and the sensor doesnt work, i.e. says the clothes are dry when they arent and we always have to run them through at least two-timed cycles to make them completely dry. The washer is another nightmare. At least 8 service calls as well, and after one where the motor was replaced, it popped off and flooded my entire house. They laundry room is located on the second floor. I had to replace floors, walls, ceiling, light fixtures, etc. Insurance covered it but it never shouldve happened. Now the washer doesnt drain properly and the error code LD displays every load and we must manually drain it by either setting an extra drain cycle or take the entire machine apart and vacuum out the water. Each load takes twice the amount of time it should, if not more. But I guess its okay because the dryer takes just as long to dry a load of clothes. Something has to be done. Maytag is refusing to stand behind their products and it seems as though many of the complaints are for the same issues. Is there a lemon law for household appliances?

My husband bought me a brand new Bravo Maytag washer and dryer from Home Depot in November 2010. In May of 2011, we moved and the dryer hookup was electric instead of gas. My husband knew how much I love the dryer, so he surprised me with another Bravo dryer to match the washer. We put the other dryer in storage and were happy with our purchase until April. In April 2012, the dryer stopped working. It wouldnt dry the clothes at all, and every time we tried to dry, the dryer was filled with wet lint. We were only a week away from moving again, so we waited until we got to the new house. The new house had gas hookups. So, we put the dryer that didnt work in storage and were thankful we didnt get rid of the other dryer. Now, just a few months later, the gas dryer isnt drying and is having the same issues as the electric dryer. How very disappointing! Both dryers are broken now, and it has only been 2 years. Each dryer has gotten about a year of use and then both quit. My husband, I and my two-year-old dont do that much laundry to break 2 dryers. My old GE washer and dryer lasted for years and is still working. We gave them to my husbands aunt who uses them and loves them. I agree someone should start a class action against Maytag. These issues are ridiculous!

I purchased a Maytag Centennial Commercial Technology washer in September 2010 which is less than two years ago. It decides to stop spinning correctly in the Spin cycles. Clothes come out sopping wet so I contacted Maytag to have a tech come out. On the day that the tech came out from A&E Factory Service, he stated it was a switch. He changed the switch and still, it did not spin correctly. He then proceeds to state that it is another part, which again, it did not do the function correctly. He then proceeded to state that it is the clutch, then the transmission. The cost was raising to $519.00.I stated that I did not want to proceed because I would be purchasing a new washer with that quote. I stated to place all the original parts back onto the washer. He did so, but did not place them on correctly. The casing of the washer no longer is secured to the drum - bolts and plastic pieces are still on the side. He left my house with finger prints of grease on the walls. If this is the workmanship that Maytag recommends, then my business deserves to go elsewhere.A complaint was filed with the A&E Factory Service. However, no one has contacted me about the complaint as was requested. All I want is for my washer to be fixed or to have a tech who is knowledgeable to come out and fix it. I contacted Maytag to inform then of the situation and they stated that all their techs are certified. I do not believe that my washer of less than two years old could possibly have so many parts that are faulty. I hope that this may, in turn, help another consumer to avoid purchasing washers through Maytag and their parent company, Whirlpool.

I got a new washer and dryer for my ex wife and son last August. Its October and the agitator broke off. She is not abusive to things and just the two of them dont produce much laundry. This was just poorly built. Maytag should be ashamed to have built such a poor product. I thought GE had the worst appliances, but Maytag must have hired their engineers. I have pictures and it has 10 year warranty right on the lid, lol. Should be 10 months,

It has never failed me and I cant remember when we purchased it. When I grew up, my Mother only used Maytag Washer and Dryer. When I married (almost 50 years ago), I purchased a Maytag Washer and Dryer and have never regretted it.

I bought a Maytag Neptune washer and dryer set in 2001. I had horrible mold issues with the washer not long after, and the colors washing setting cant be used without the clothes coming out with a smell that implies they were not cleaned. The dryer lasted about a year longer, before it stopped heating the air and also would not stop running. I will never buy from Maytag again! Much the same as many other consumers have commented, I would give it less than one star if that is an option!

Maytag used to have a reputation for quality. Their low water energy efficient Centennial is a waste of money. Half of the time clothes come out wet and most of the time they are still dirty. Also you are only supposed fill the tub 1/4 of the way with clothes so you end up doing 3 times as many loads per week. What genius came up with this idea? Save your money. You would get better results washing your clothes in a tub with a washboard. Seriously!

In 2006, my wife and I purchased a new Maytag refrigerator, the model type with the freezer in a drawer near the floor and the drawer is under the main door of the fridge. The thing has a sealed system and has a freon leak which makes it nearly impossible and not financially prudent to try to fix. Two repairmen were out and I spent $200 for them to tell me the same bad news. Its unbelievable that this junk wouldnt even last ten years. What is this, Russia? Ive heard some of their awful appliance experience stories and now this can join them. The reliable Maytag repairman who never has anything to - you know the one. He is probably dead. Hes not really the one to blame here though, it is the reliability of Maytag that is dead and will remain so for as long as this company is alive. Dont ever trust or buy Maytag if you care about making your investment in new appliances last! Dont do it, people!

We bought a top load washer and the matching dryer. A thermal switch (I think it’s called) blew in the dryer at about two years. Luckily my husband is an electrician, so he took care of that. WASHER-A little after 2 years the plastic “driver hub” stripped And the agitator has stopped working, the door is having trouble locking and it won’t spin fast enough to get the water out of the clothes. I’ve ordered a new “driver hub” for $53! It is a cheap plastic part. Probably 1 cent to make in China. Robbery. This will hopefully resolve all 3 issues I’m having with the washer. They even charged me 9.99 shipping. $2000 later Maytag/Whirlpool should treat their customers like royalty. I will never ever buy another Maytag or other brands associated with Whirlpool ever again.

When I went to whip down the small shelve under the knobs, I cut my finger on the sharp metal. Was told that is the oven vent. Checked out your instruction book and found NO mention on that being a danger and to take care when cleaning. If I had been informed of that sharp metal piece I dont think I would have looked at your stove. The metal has razor sharp edges on both sides making it almost impossible to get too close to cleaning it. That shelf is a nice place to collect dust, grease and food boil overs and now I have to be extremely careful about cleaning. Thanks to someones not thinking in their designing. The stove is what I wanted other than that one fault.

1998 MAH4000 - I got this unit (used) in 2004 for $400, and it has pretty much kinda been a lemon ever since. I have babied it through until now, though it had the wax motor repaired twice (Im glad I bought an extended warranty from Maytag, but that added $400). Now the motor control has gone out. I like the concept of the front-loader, but my folks Maytags (and my grandparents) have run for 30+ years without any of the hassles Ive had.Granted, I like bleach, so the mold thing has been less of an issue for me, but wow. I have to say I wont ever purchase another Maytag appliance again. Im about to drop the $185 for a new motor (the motor control board went out, and apparently I need to get the new motor and control). Im pretty sure I lost a phase based on the burnt components on the board. Im glad I know a bit about electronics, or else Id really have been in for some money. Boo on this model!!

I had another Maytag washer. It lasted 21 months. BB got me the BravosXL to replace it. I have had it 6 years. It is a piece of junk. Goes out of balance all the time. We are 2 ladies and don’t have heavy clothes to wash. I am washing now. I have put It through a wash cycle. The soap is still on the clothes. I am on my THIRD rinse cycle and there is still soap on the clothes. And I used less soap. Never again MAYTAG.

Our brand new Maytag front loader has a optimum (LOL) soap dispenser that can supposedly wash several loads before refilling. BUT, the dispenser fills with water after one load and dilutes whatever soap is left! We talked to a authorized tech who said it was a poor design. That the unit wasnt sealed from water or it would be under vacuum. We called Maytag and they said something like, Um well it has sensors!! Did they explain how it would sense the diluted soap concentration? Nope. It should be replaced by MAYTAG! Knowing it is something that they sell that is defective. Right out of the gate!! The engineer should be fired, the quality department heads fired too!

I have a 26 cu. ft. side by side Model MZD2665HES, like most folks in my neighborhood (spec homes). The icemaker died and service was called. They looked at solenoid, and replaced the ice maker assembly as a wag that it was the problem.. still no ice, but the water was still able to be called. I replaced filter- still water only, no ice. Little did we know it was the filler tube blocked with ice, and the service man didnt once suggest turning off the water service. SO, every time water was called to either make ice or to fill a cup with, it put intense pressure on the point of assembly where the water line comes into the fridge (water inlet tube). A pin hole developed in the little plastic bit (water inlet tube plate) and every time the water was called to ice, guess what happened - it shot right out the back on drywall.Almost $20,000 dollars worth of damage to wood floor (warped), drywall (jello), and flooring (carpet) ensued. Mold was all over and had to be contained and treated for days to be fixed. Im still duking it out with service repairman and insurance companies. My advise: If you have this fridge or anything like it and the ice maker stops working, IMMEDIATELY shut down the water supply, turn the fridge off and check the filler tube in the back for ice blockage. Probably a good idea to pull the fridge forward once in a while and check the back for water also.

I purchased a very expensive set of Maytag washer & dryer (topload washer) and heavy duty larger capacity. Firstly- I purchased this through Home Depot on Labor Day weekend and did not receive this set until December 2020. This set has all the electronics and Im going to tell you NOT to purchase either one. The dryer MUST have a metal solid vent. This sets your dryer out into the walkway of a laundry room. If you use a heavy flexible metal vent; your sensor will be going off constantly telling you your vent is plugged and to clean it. I had a dryer vent company out twice to clean and inspect the wall & roof vents yielding nothing. I also have a dryer vent cleaner which I hook up to my vacuum and I clean the dryer vent monthly. If you lose power. You will need to unplug your dryer and let it reset to be able to use it.The washer is also terrible for the outrageous price. Again; glass heavy duty top load with all the electronics. You cant get the washer to fill even on deep fill. Also; do NOT put a lot of clothes or jeans or blankets in this machine. It will not be able to level and spin. When you try to use the drain and spin cycle; the sensor keeps going off. I swift the contents around and around and finally end up having to take soaking wet cloths out into the garage until I have one sheet in the machine and it will spin out. In addition- the CLEAN with Afresh mess. This forces you to clean your machine- whether you are in the middle of trying to get clothes drained or not.Buy something thats a simple workhorse with one button. Stay away from any bells and whistles because its only going to cause you heartache in the long run. I wish I would have read reviews prior to spending $1,700 on a Maytag Washer Dryer set (ON SALE- for God sakes). This is the biggest piece of garbage I have ever purchased. Buyer beware.

Bought in July 2015, brand new from Lowe’s or Sears. When working to its full potential it never cleaned clothing very well, had no designated spot for detergent or softener, just bleach. Just last 3 years and it’s a piece of crap that has to be replaced. Going to argue with the company to tomorrow to get them to replace the broken transmission which may or may not be considered part of the drive motor - all **. This is a very expensive machine that didn’t last a month beyond 3 years! The 10 year warranty covers the 2 most rugged parts of any washer... the agitator never truly cleaned my clothes and now it is fused to the wash basket and cannot even be replaced without being chiseled off. Worst machine, purchase, and brand ever???

WOW! I cant believe I bought a Maytag MDB7749AWM1 Dishwasher without reading any reviews. Paid $650 for it a couple of years ago and the control panel is bad. $390 to repair it, unbelievable! Sounds like Maytag has a major customer service problem because I will NEVER BUY A MAYTAG DISHWASHER again! Spent $5000 grand on new Maytag appliances thinking they were the best to replace the outdated ones. Not the same, not sure what youre doing Maytag but youre losing a lot of loyal customers. What a shame! My old dishwasher lasted over 18 years and I didnt have any problems. 2 years? Come on!!! Same problem as the other 5000 people, someone needs a career change!

I purchased a Maytag made by Whirlpool in China about two years ago. The timer went out about nine months later. It went out again about 3 months after that and I paid to replace two sensors in addition. The washer still stops during a cycle at various times; it might be pausing or spinning or filling. When it finishes washing, sometimes it refills and leaves everything wet. I purchased from Deweys in San Clemente and they have tried to service but this is a real lemon. I will never buy anything again made by Whirlpool. I will research and find out what companies have been bought by them so as to avoid this. I note online that there are several hundred complaint problems about Whirlpool so they had to buy a company with a good reputation and ruin their product.

I purchased a Maytag Epic Z Front Load Washer less than 5 years ago, and there is only 1 person in my household. I replaced a part that the technician said was bad for $300 and that didnt work, so they replaced another part for another$ 200. Then, when that didnt work, Whirlpool deemed my washer irreparable, and they will not stand behind their product. This is totally unacceptable, and I will never buy another Whirlpool product. I will also tell others that they do not stand behind their product. If this was a 20 year old product, I would understand but it is not typical for something like this to happen.

It looks big, but is small inside. Its hard to put in several large items. The water filter broke and too expensive to fix. I like the double doors and ice maker. I dont like the freezer drawer. It wont stay open to clean.

The frontload washer 4000 series began making a very loud noise on spin. I called Maytag and requested service. The technician came and made a diagnostic evaluation, stating this has been a bearing defect affecting several of these models. I called Maytag, and the representative agreed to ship the parts at no charge. A week later, we received the parts, only for the technician to find one of the parts damaged in shipping perhaps. So another part was sent directly to the Maytag dealer. Upon my research, this appears to be a known issue with the Maytag/Whirlpool corporation, and I found where customers had requested Maytag to also be responsible for the service/labor costs, which were also covered by Maytag. I made the call today and was advised no and to be happy that Maytag paid for the parts due to a known defect and that no service or labor charges would be covered. I understand my machine is out of warranty, but this is a known defect; its nothing caused by my self.

The water got so bad it damaged my cabinets. I called Maytag, they admitted my model was sent out with no drain hose so this entire time my $2000 refrigerator had a missing part that they are very aware of. The part was free but I had to pay for the service. Its still leaking on the floor because the drip pan got fried from having no water in it to evaporate so it melted my drip pan, now it needs more service that I have to pay for. I have no faith that this will fix it. I will never buy Maytag again it feels like cheap plastic. I would love to start a claim against them for taking our money knowing the refrigerator has missing parts. Now Im part of the towel on the floor club group.

I moved into an apartment home in June 2016. My apartment was furnished with all new appliances. The washer & dryer were purchased in May 2016. I live alone so on average I do 1 load of laundry per week. In November I noticed paint peeling on the inside of the dryer drum. Each time I use the dryer more paint peels. I contacted Maytag because I figured the dryer was still under some type of warranty. They sent out a technician only to tell me this was a cosmetic problem and cosmetic problems are not covered under the 10 year warranty. I would need an authorization code from Maytag if it was covered under warranty.Again, I contacted Maytag and now they want to send another technician for a second opinion. I dont feel this is cosmetic because the dryer is only 6 months old and already the paint is peeling. I feel this is a product defect because this type of problem shouldnt happen on a new appliance. I have scheduled an appointment for a second opinion and if he says its cosmetic then I have to pay out of pocket for the repairs to fix the problem. I thought Maytag stood by their product and customer satisfaction was a top priority. I guess I was wrong.

Just after a year the bottom freezer began to build up frost. I had to thaw it every day. A repairman changed part and ran well for about 5 months when it started to frost up again. Again, I had to call a repairman in. $500.00 later, my fridge is working again. I am done with Maytag appliances. Never again!

My Maytag 3000 series washer had to be worked on right after we purchased it. Now it stinks and is leaking. Repairs are going to be over 300 dollars. A part wore out. It should have lasted longer and why does the front loading washer stink. There is no door to open to clean the filter.

If you are considering this product...RUN AS FAST AS YOU CAN!! This is the biggest piece of junk Ive ever owned!! I would be more than happy to take back my 20+ year old washer over this JUNK!! It is 2-2 1/2 years old tops. I cannot count how many times my husband has already had to repair this garbage!!! I will NEVER purchase another Maytag appliance! My stainless steel dishwasher isnt any better!!

Our Maytag Elite Series dryer is not under warranty but we have had nothing but issues with this dryer since we have had it. However, now I have holes in the heat intake at the back of the drum. This is so very dangerous and could cause a fire. I am certain this is a manufacturing flaw. How on earth does the inside of a dryer have parts that will not hold up to heat? At any rate, I want it fixed. The only way to fix it is to replace the drum. This has to be a flaw in design or manufacturing and this particular model should be recalled.

I have had 2 Maytag washers in 37 yrs and loved their products, however I purchased a Maytag quiet 300 in 2/09 and it is the worse Maytag product on the market. The frame around the bleach dispenser has rusted out and I have called for the 3rd time in 5 years to have it repaired. To my dismay it will cost 300.00 to fix because the bearings have to be replaced. I will now have to purchase a new washer. The days of the Maytag man are long gone. By the way the Maytag dryer has been serviced twice. I thank God everyday for that extended warranty I bought, but now it has now expired.

I purchased this new a year and 4 months ago and have had nothing but issues. We thought it cooked slow or cooked high/low but couldnt be sure if we were just imagining it until we had family come down at Christmas and complain about how slow the top burners are and why is it taking so long to boil water. Then again family for Easter where they cooked three days in a row and they complained that our top oven either burns or under-cooks the food which we had noticed but presumed we just mistimed a lot of food. Just recently the bottom oven wont heat past 350 and just constantly says preheating. The top oven followed suit shortly after. Nothing past 350.

This dishwasher is extremely quiet and very attractive in the kitchen. Easy to use and does a great cleaning job. The price was also right. Would definitely buy again.

I bought this Centennial washer about 7 weeks ago and it has worked right for 4 of those weeks. The washer wouldnt spin the clothes and they came out soaked. Service guy came out and said it was the computer panel and he didnt have one. So I waited over a week for another service call. He put that one and said that now the transmission was shot and he didnt have one, another wait. This is a piece of junk. Do not buy Maytag or Whirlpool products. I had a Maytag for 15 years and had one service call. They are not what they used to be.

This product has been a huge disappointment, from day one. It wrinkles and tears clothes beyond recognition. When I called Maytag to complain, they tried to up sell me a service contact. I explained that it works fine, as a shredder, but it is just a bad design and asked if Maytag had any recalls. He then told me if I purchase the service agreement and they cant fix it then they will refund the $$... ITS NOT BROKEN. It was crap when we got it home. Shame on me for not taking it right back to Best Buy. Someone needs to start a CLASS ACTION SUIT. I am sure they have duped many people into buying this shredding machine...

We bought a new dishwasher 2 years ago. Top of the line Maytag Model #MDB8959SBW3 $749 plus tax. We bought this one because they told us what a great 10 year warranty it had. Found out that is a lie. The only thing the 10 year warranty covers is the stainless steel tub, the racks and chopper blade. The stop button on the control panel (circuit board) quit working and the dishwasher wouldnt start. When I called Maytag they said So sorry. It broke so soon, but that is not covered.We were told by a repair shop that Maytag has had nothing but problems with their control panel and the control panel part alone is $150 plus tax plus installation. Our old Maytag lasted 13 years and was still running great, but needed to be replaced because the racks were rusting out. I wish I would have kept the old one. I will never buy Maytag again since it is now made by Whirlpool. If Maytag is having so many problems with their control panel, they should be recalling them.

I owned an front loading Maytag Neptune Front Load Washer MAH5500 for more than 10 years and first 5 yrs doing 2-3 loads a day for a family of 12 so this machine held up well, and only issue we had with the machine was the rubber around outside needed to be replaced after about 9 yrs.

All my kitchen appliances are from Maytag, however I would highly recommend buying the extended warranty for any appliance you buy. Maytag is not helpful to customers when it comes to repairs. They will recommend you their authorized companies which here in Colorado Springs are the one with the worse review and already knowing the the repair will cost more than the cost of a new one. You will have to be available 5 hours of your day and spend $110 for a guy to come to your house and tell you that the repair will cost more than a new one. Oh and if your microwave is a 2.0 CU like mine you will have to pay $300 plus in double labor because your microwave will require two people to take it down from the kitchen cabinet.

One year ago I bought a Maytag Micro-wave and a Maytag dishwasher - big mistake. I should have done some homework. I had problems with the dishwasher since the day it was installed. I should have suspected something was wrong when it was delivered. I opened my front door and there stood a deliveryman holding my dishwasher in his arms. He said, Where do you want it? I couldnt believe he could be carrying it by himself, especially since it took three of us to move out the old Thermador which by the way was still working just fine after almost 30 years. But my wife insisted on a new washer for her new kitchen. The Thermador was actually made of steel. The new Maytag was made of plastic even the motor. It had some steel and copper parts but mostly plastic. I dont think it weighed forty pounds. The problems began the first day with leaks through the door and under it. I suppose eight or nine service calls happened in the next 3 months. The factory service men were different each time and each had their own guess as to what caused the leaks. Over time they replaced all the parts that could be leaking some of them twice, because subsequent servicemen discovered that a previous service man had installed the wrong parts. We often had to wait several weeks because replacement parts were not on hand, and would be ordered and shipped directly to us. Then we would have to schedule another service call, only to find out the wrong parts came - more delays. One service man told us we were using the wrong detergent, even though it was the detergent and spot-free rinse that came with it. Another service man removed the door cover so he could watch to see where it was leaking when it operated. He said the soap was foaming too much and flooding over, so we had to try another brand of soap, even though by now we had accumulated three other brands that were just barely used. The service men never did fix the problem. It took much experimentation from my wife to stop the leaks, which meant we could only use a fraction of the recommended amount soap. By now we were using so little soap that the dishes always came out dirty. So our choice was mop up a wet floor or have dirty dishes every time. Most of the time now we wash the dishes in the sink. One service man said in Maytags effort to make the dishwashers more efficient, and less expensive to build that the motor and pump were way under powered, and everything was made from petro-chemical by-products (cheap plastic) and that we should invest in the extended warranty. Its cheaper than paying service calls when the warranty runs out soon. What we should have done was exchanged it for another brand. My wife said had she only known, we would have never replaced the old Thermador which will be my next dishwasher. As for the micro-wave there are many things I dislike about it especially the rectangle glass tray which is extremely awkward to remove and replace each time you have to clean out crumbs and spills which happen often. The timer on/off bell is way too quiet with no volume control. The message and operation display is difficult to understand. And to top it off the cheap plastic handle broke one week after the warranty ran out which I found out that its less expensive to buy a whole new door than pay for parts and a service call to repair handle. Maytags track record made me not want to deal with service dept. again. I will probably be money ahead to trash the two appliances, start over and do some homework and maybe buy a European made appliance. I know German technology is not all about profit making, but quality, reliability, durability. I hate to sound un-American but greed in American corporations will be their downfall.

After my divorce, I bought a new house for my youngest son and me. It came without a fridge, so I used some of my settlement money to buy one I had been dying to get - stainless, French door, with bottom drawer freezer! It worked fine for the first 9 months or so. Then, water started pouring through the ceiling of my downstairs master bedroom. Turns out it was coming from the freezer water line. Ceiling tiles ruined, carpet stained. Then it started making this god awful noise. It starts, rumbles for a while (long enough to wake everyone up or give the dog a coronary), then is quiet for a while. Next, I open the freezer to find a sheet of ice across the bottom of the drawer. I assumed I had done something, so I got rid of it and thought nothing else of it. Last night, I get ready to make dinner and there is this blizzard of frost all over the freezer. It looks like a winter wonderland. I am afraid to see what is there when I go home and even more fearful to attempt to use my warranty.

This is beyond one of the most disappointing purchases I have ever made! It has been about 15 months since purchasing this dishwasher, and as of today it is not working! Blinking start button. I see from the hundreds of disappointed customer comments that I am not alone. With this many people complaining of the same issue, that Maytag should have a recall... I paid about $550. I get that quality does not supersede the almighty dollar, but come on!

SO SO disappointed. I thought by purchasing a Maytag washer and dryer that I was purchasing quality products. Not so. After only 3 yrs, the dryer is broken. It needs a new heating element assembly at $139 plus a visit from the technician and installation. In total, it will cost about $300 to repair. The washer is slowly going also. It takes about 2 minutes before it starts. Never used to do that. The technician told me that these do not last and that the computer is likely to go in another couple of years which will cost $400 to repair. I called Maytag to see what they could do for me. They offered the part at 1/2 price but insisted on another diagnosis even though Ive already had one. That along with their labor cost was going to cost more than anyone else. So no more Maytag products for me.

Problem with the front panel are the dishwasher has been replaced 2 times in 3 months. Was told by the tech repair person is not a well made product. He would replace it if he could had a warranty and added a new warranty for 1 year and is up again and of course have to do it. Was told if it happens again they most likely replace with a new unit. Hopefully. Not happy.

Big mistake. Worst purchase ever!! These high-efficiency washers (Maytag Washer Bravos XL) are the worst especially this one! I wash and wipe down the washer drum more than I was my clothes. I purchased it because it had a huge drum so I can wash my blankets and comforters. This washer leaves soap scum marks/residue on clothes and leaves it on the drum as well. I basically have to wash my clothes twice once with soap and then run again with just wash and rinse without soap, you tell me how efficient is that! Why not make a washer that put more water so the clothes can get washed properly. Dont worry about my water and electric bill. MAKE A WASHER THAT WORKS!I called customer service she asked me if I use the deep water, now you tell me why am I going to use the deep water, if that is the only way the washer is going to clean the clothes then do NOT give me 11 other options the washer to use. ONLY HAVE DEEP WASH OPTION. I dont care about the bells and whistles, I do not need a different tune when I turn it on and a different tune when its done washing my clothes. Make the washer the way it used to be WASHES CLOTHES WITH WATER AND LOTS OF IT. I will pay my bill not to worry. So I called customer service all they said was they will document my call! Well... like thats going to do me any good while I am stuck with your POS washer!

I live in Southern Indiana and bought my appliance from Charlie Wilsons for 25 years. 3 years ago my Whirlpool washer quit filling up to full level. I decided to move it over and use for my car and pet towels. When I bought my hose in March 1999 every appliance was Whirlpool washer, dryer, refrigerator, stove, dishwasher. GE is made in Louisville, KY but I dislike the union.Anyway I bought a Maytag model MVWC415EW1 June 2017. Recently it started making a grinding noise when going in spin cycle, wadding cloths up and leaking black water on basement floor. Called repair shop out. I just do not have the time to repair stuff anymore. They came out $80.00 service call and tell me at least $300.00 to repair. Wait a minute. $500.00 to buy a new one over $300.00 to repair. Guess what I did? I called Maytag and complained. CASE NUMBER **. They reviewed and denied. Not a problem. I said, I guess you do not need me as a customer anymore.I have twenty year old Whirlpool washer and dryer still running, I have replaced my refrigerator (Old one in garage still running a colder than new fridge and day of the week). Bought Amana=Whirlpool and it has quit and replaced with a Whirlpool July 2019. Nothing is built like it used to be BUT we still pay as much if not more. Off I go to Charlie Wilsons to buy a $1000.00 Speed Queen washer with 7 years parts and labor warranty. Had to order it but old washer still running just not going to full mark.

Purchased a Maytag washer and dryer 6 years ago and everything was fine until 3 weeks ago when the washer stopped spinning. We knew we were out of the 1 year warranty and contacted a repair service, who told us the bearing was no good. Contacted Maytag who offered in goodwill to pay for the parts and we would pay for the labor. A different repair person came in and told us the washer has no bearings but a transmission, which went bad. They ordered the transmission and today the repair person was in to install it. He installed the transmission, but while trying to take out the old one he dented the drum. According to my husband the repair person banged so hard that it sounded as if something could have been damaged, sure enough it was the drum. Contacted Maytag to see if anything can be done as now we still have no washer, and the repair person was their selection not ours. All we got from Maytag was they are not responsible and there is not much more they can do. I cannot believe the last Maytag product we had lasted over 20 years and this one is less than 6 years with problems. Will not purchase another of their products again.

I bought a Maytag Centennial Top Loading washer 2-1/2 years ago. Its worked very well, but has started to roar so loud on high-speed spin that you have to leave that side of the house to be heard. The factory technician determined that it had a bad gearbox and that it wasnt anything I had done that caused it. He told me it was going to cost more for parts & labor than the machine was worth. I called Maytag and was told they wouldnt help me because it was after the one-year warranty. When I asked for a supervisor, he offered to pay for the parts, but not the service. Thats kind of like Chevy offering to pay for the defective engine part, but not the installation. I have never bought a major appliance (or even a hair dryer) where I thought 3 years was a reasonable life expectancy. Lifelong Maytag Customer has left the building.

I would not recommend the Maytag washer with the large tub. It does not clean your clothes. I called Maytag and they do not care as long as it uses as little water as possible! Not a good value for the money!! That was the first time and last time I buy a Maytag... Thats the last $5000 they will get from us!

I agree with everyone else on here. I would give this Maytag Neptune washer less than 1 star if I could. I also purchased this washer 5 years ago when I bought a new house. According to their commercials, the Maytag repairman is bored because their products are so great. I believe it is because the cost to fix their merchandise when it breaks costs so much.I had a 5-year warranty on my purchase and this washer started making this awful noise but the company wouldnt repair it because it was not broken. However, here I am less than 5 months later, and the bearings are so bad, the tube is scraping and falling apart and leaving plastic pieces in my clothes. I have a 3 year old I dont need plastic pieces in my clothes. You know my husband just left me and I do not have the money to spend on the repair ($500-700) nor have the money to spend on a new washer. Thanks Maytag for your great and wonderful service!

Most every post about Maytag/Whirlpool dishwashers reads the same. Mine is no different. The control panel on my model MDB7749SBM1 has failed after about 16 months of use. Its a lose-lose situation for the consumer, as the cost of parts and labor for the repair equals or eclipses the replacement cost of a new unit.Another fine example of the degradation of an American brand, once known for quality and reliability. Dont be fooled by the branding. Buyer beware!

After less than two years the commercial washer we purchased from Lowe’s died. A repairman came out after a week and said it potentially needs a new control unit or computer. The control unit is on back order and we’ve been without a washer for a total of three weeks. The situation still remains unresolved and I’m regretting not going back to Samsung. After 9 years with a Samsung washer, it died and Samsung refunded the full price of the washer. It was a poor choice to choose American. :(

I bought a fridge, model number MBF1958, its a top fridge-bottom freezer. The freezer part leaked and spilled water that then froze onto the bottom of the freezer, which of course froze. I discovered this 1 month after the 1 year warranty ended. Maytag gave me a courtesy repair service guaranteed for 90 days. Of course, 2 weeks after the 90-day period ended, I have the same problem again.

We have a Maxima washer which is about two years old. The tub around the barrel cracked and flooded the laundry room. The repair person said it would cost more to fix than replace. Very unsatisfied. We are trying to deal with the company but not optimistic.

Freezer does not freeze well. Causes most our food to get freezer burned. We tried turning it up and down but made no difference. Actually went and bought a separate freezer for meats.

I purchased this washer two years ago. It is supposed to be high efficiency so I was using cold water with the Water level sensor. The first load of dark clothes I washed came out with soap streaks all over them. This happened every time I washed dark clothes and sometimes they were barely wet. I emailed Maytag but they didn’t reply, so I called customer service and was told I should always use warm water and when washing dark clothes select a deep water wash. How is this HE?? When I wash towels or sheets everything comes out tangled and I am only putting in one set of queen size sheets. I will never buy another Maytag.

The washer does not get clothes clean at all even with the help of odor blaster, does not spin right, does not even out the clothes, walks while it is spinning. My towels do not smell good at all. The dryer gets too hot and the lint trap is always a mess even though I clean it after every use.

I bought your Maytag model MDB7749SBW1 dishwasher on May 22, 2013. We bought Maytag because of your reputation...not because of price. However, in September, 2014 (2 months out of warranty!!), the control panel stopped working. I called the 800 number and the best they could do is to extend the warranty for 6 months BUT only after we paid for repair and control board replacement. This is not cheap!!! We were furious. I looked if there were recalls on this model but there is not (should be). Anyway, after we paid for repairs and a new control panel put in ($160.00 +- for part itself), we were very cautious about touching anything on that dishwasher. YOU HAVE an issue with design and I can give you link after link of other customers who have expressed the same thing. So, here we are in 2017... About 2 months ago, we noticed the exact same symptoms with the control board.In fact the ONLY way we could start the dishwasher was to turn off the breaker, let it sit for 20 minutes - overnight and then turn back on and hit the start button. We lost all control over the settings. Only auto clean and delay 2 hours were working. Yesterday, I purchased yet another control board ($179 incl tax and shipping). I plan to install myself. If I could afford another dishwasher, I would do it and never buy Maytag again. Maytag really ought to be ashamed and if they were truly concerned they would offer these defective parts at a steep discount or better yet, recall. I plan on submitting something about this issue with any consumer group I can find. I guess the only way to spread the word and perhaps force a company to respond is to post on social media anymore. This is NOT a like.

Our washer sounds like an airplane taking off. Called a repair man and the repairs are $690.00. The washer cost $999.00; such a waste of money. I called Maytag and they say there is nothing they can do. I will NEVER buy a Maytag again.

My Maytag MDB7749SAW0 Dishwasher starting acting up after around the first year. The lights on the Control Panel began to flash uncontrollably and it will run all day while I am at work. I called Maytag and they were nice but did not repair it because the warranty just ran out. The person on the phone said that it is a common problem with knob-less dishwashers, the humidity causes problems with the control panel. The cost to repair was over $300 to replace the control panel.

Purchased washer less than 2 years ago. Loud noise like a jet engine or helicopter in spin cycle. Did not purchase the extended warranty. Called Whirlpool/ Maytag customer service. Was told I could have one of their repair people come out. I would have to pay $300 which would give me the repair and extended 1 yr warranty, or I could get $300 off toward a purchase of a new washer. Are you kidding me? This washer wasnt even 2 yr old and making this horrid noise in the spin cycle. I had to have a independent repairman for Maytag washers come out to tell me it wash the bearing and would cost 3 to 4 hundred dollars to fix it. I said no thanks and after his $90 service call am stuck listening to this piece of junk make noise till it completely breaks. I will never buy a Whirlpool product again or recommend one. Whirlpool you sell nothing but junk.

Maytag msd2650kes refrigerator - I replaced compressor switch three times then compressor went out after only almost four years. We bought all new Maytag when remodeling. Never again will we ever be that stupid again.

I contacted Maytag, and they claimed to know of NO issues with this fridge. I told them its all over the internet, many others with the same fridge and same problem. Anybody up for a class action?

I bought a new Maytag dishwasher 9 months ago from Costco - Maytag 24 in. Built-in Dishwasher with PowerBlast Cycle, White. This dishwasher needs a new motor - Please do not buy this dishwasher. It is garbage.

I bought a top of the line Maytag commercial washer. We had a number of service calls replacing parts, gear box etc. Then, they finally replaced the machine and all the same issues happened again. They will not take back their machine or refund me my almost $1K paid. The washer squeals when it starts washing and clunks all while agitating - I can hear it upstairs. After yet another service call (#11 now and no salary replacement for me) the result is that Maytag says when the temp in the house is 67 or lower, the parts in their machine expand and contract and will make noise. No fix, no refund oh, and no one you can contact by email in Canada to help. Moral of the story, dont buy Maytag.

I bought a Maytag stainless steel refrigerator w/ freezer on the bottom. Since 6 months fridge being in my house I started to have problems, rust on the doors, water coming out of the bottom, freezer door got stuck w/ ice and couldnt be opened, butter, eggs, milk can be frozen one day and the next they have mold and bacteria because of the changes in the cooling system, among my problems. And what? Well yes thank you so much for the guarantee Maytag has in Puerto Rico, IT SUCKS! They been in my house more than 5 times and nobody really says whats wrong. They supposedly change the computer, still having problems, and this was done after more than three times visits from Maytag guarantee. Im still paying for the damn fridge and DO NOT HAVE A RELIABLE REFRIGERATOR. Im wasting too much food, Im obligated to buy food almost every day cause Im scare to give something that may be bad and my family will be food poisoned. Whos going to pay me or my family if something happens. Maytag is still running falsely commercial ads and somebody MUST STOP THEM. This appliances are not free or cheap. PLEASE help us because Ive learned that Im not the only one having problems in Puerto Rico w/ Maytag. Also I believe Maytag is using technicians not ruled by the government of Puerto Rico and thats why the service is horrible.

When our ice maker (Model # MF12269VEM10) stopped working, we contacted Maytag, only to be told that the 1-year warranty had expired. So we had no recourse but to contract a repairman. He replaced the valve (and in the process, because of Maytags decision to use plastic tabs instead of screws, the tabs for the filter housing broke off in his attempt to reach the rear of refrigerator where the valve went and we had to pay to have the housing replaced, also). The new valve did NOT fix the problem. Water continued to run out of the water dispenser after you removed your glass. We re-contacted the repairman who returned and proclaimed that there was air in the lines and it should work itself out over the next several days. Yet that night, I noticed drops of water running down the control center and filling the drip tray. I placed a towel on the floor and emptied the drip tray several times that night, before turning off the ice maker completely the next day.Unhappy with the original repairman, we contacted another who came out and discovered that the new valve was leaking from the top. That is when the filter housing broke and we had to use duct tape to hold it in place while the new repairman ordered a replacement. He tightened the valve and cycled the ice maker several times only to discover that the water overflow switch on the ice maker wasnt working, thus water was overflowing into the ice maker container. He turned down the water pressure to the refrigerator, and we tested it again. All seemed to be well until the next day when no ice was released from the ice dispenser. When I removed the ice storage bin, I found everything frozen from water overflow. I turned off the ice maker entirely and contacted the repairman, who ordered a new ice maker, which took about a week.After the new ice maker was installed, along with the new filter housing, the repairman cycled the unit several times before leaving. Yet by the next day, the ice in the storage bin was frozen in place again (I have pictures), and we contacted the repairman who ordered yet another ice maker. It took yet another week for the part to come in. After it was replaced, I monitored the ice container each time I heard ice drop into it. The 1st time there were a few drops of water in the bottom of the ice maker. The 2nd time, there was a 1/4 cup of water in the bottom. I immediately contacted the repairman to let him know and turned off the ice maker yet again.I find it hard to believe that a new valve, fresh from the package, and 2 (TWO) ice makers, fresh from the box, were all faulty. The repairs started on February 25th 2015. It is now March 21st and the ice maker is still not repaired. The 2nd repairman is doing his own research into the problem (for which we applaud him!) and now we ask you for your feedback as to the problem and how it can be solved.

I bought a new top loader Maytag washer and dryer on 1/1/16. My first experience with the washer was as many in has stated - It Doesnt Clean, the clothes, also I have trouble with the fact that is there is a string loose, it become worst. Why did they improve a product that did not need improving. They just made it worst. It is totally **. Im stuck with it as I cannot afford another washer. The dryer work fine.

The Maytag Bravos washing machine may well be the worst appliance available for purchase. Sure it is a high efficiency machine that saves on water -- the clothes are often still dry when the complete cycle is finished. Many times there is still soap residue on the clothes. Forget cleaning anything with any amount of dirt on it because it seems as though items are even more filthy after washing them. I have tried everything the company advised and still my clothes are not clean. My advice... please do not purchase this machine. You would be better off taking your clothes to a river and beating them on a rock. #wearingdirtyclothesforever

I find this Maytag dishwasher just ok, nothing special. It doesnt seem to clean any better or worse than other dishwashers I have had or used in the past. It also seems to get really slimy under the inside of the door.

Maytag Bravos 300 Quiet series - Ive owned this washer for about three years. On average, I do 2-3 loads of laundry per week. I follow the loading directions, but still have to babysit the machine because of uneven load issues better than 50% of the time. Many times, clothes come out full of lint, even after running the clean washer cycle. This is the worst washer I have ever owned. Ive had better results from second-hand machines.I havent bothered to contact Maytag because Ive had it so long. Im almost to the point of getting rid of it and buying one that gets my clothes clean and isnt inclined to push the clothes all to one side and put the machine off-balance. To say Im disappointed in the product would be an understatement, especially since I paid $800 for it.

Top rack fell off with load of dishes. Clips that hold rack to slides broke. Week for repairman, two days for parts, week for repairman. No repairman, call parts be in on 7/28 2014, repairman on 7/31/2014. ONLY HAD DISHER FOR A WEEK, NOW IT IS BROKE. WHAT A RIPOFF.

I purchased the Maytag Bravo model MGDB950YG on April 22, 2012. It worked great for a while then stopped heating and drying the clothes. After going through the Maytag procedure, a repair person assessed the problem, had to order the part then came back to repair it. But the same thing just happened again! Both Maytag and HHGregg need to go through the appropriate procedures, which leaves me without a dryer for who knows how long this time. Maytag will not do next day service probably because it costs them a little more. I think Maytag should have enough common sense to sometimes make exception to this. Today is Thursday and I cant get an appointment until Monday! I have owned two dryers prior to this which each lasted 10 years plus. I would be much more understanding if I had my appliance for more than 4 months (out of commission 2-3 weeks of the 4 months). Ive never been so disappointed in an appliance!

I am writing for your assistance with an ongoing problem that I am having with my Maytag Series 2000 front-loading clothes washing machine. I am, frankly, astonished and frustrated beyond any means of coping with the response I have gotten from Maytag about the lemon washing machine that was sold to me. As I have never before had any sort of reason to complain about any major appliance purchase (nor about any car or house purchase), I’m not yet sure of what avenues are available to me. It seems prudent to inquire of your office before getting a private attorney to help me with this. The following is my situation:First of all, I am asking for a replacement washing machine. I am clearly saddled with a lemon.On or around December 2010, we purchased the Maytag Series 2000 washing machine from Cedar Appliance of Medford, MA. Within the first several months, the washer started ripping, shredding, and putting holes in our clothes. This did not happen during every wash cycle, just sometimes. At the time, we didn’t know if it was the washer or the (also new) Maytag dryer that was causing it. After living with this for some time, we decided to call Cedar Appliance for service. Cedar came out several times to look at the machines and they couldn’t tell what machine was causing the holes. Eventually, I started examining every article coming out of the washer to determine which machine was causing the problem. Over time and many visits later, Cedar Appliance referred us to L.A.R. Service of Wakefield MA, which they called Maytag service.L.A.R. Service came out and looked at it. They said that we were missing a part. They ordered the part and installed it and said everything should be fine. They also sold us an extended service contract. I am still having the exact same problem with the machine. Today I called L.A.R. and they told me that I had to call Cedar to get an authorization for service. I called Cedar and they told me to call Maytag. I called Maytag and after spending an inordinate amount of time recalling the details, the service representative told me that I could pay up front for an extended warranty and they would send someone out. I asked for a supervisor. I got Kitty. Kitty told me that Maytag would not replace my machine, which is clearly a lemon because I hadn’t yet had enough service done on it. I explained that I have spent hours calling for service, scheduling service, waiting for service, supervising service, and paying for service. She explained that on only one service call did they install new parts, so I needed more service. So, I should have demanded new parts on each of these service calls so that I would have earned some credibility for my lemon machine?The fact is that my family and I have lost hundreds of dollars on torn and ruined clothing caused by a new washing machine! After the boot was installed, or replaced (I’m not sure exactly what was done), we are experiencing the exact same problem. When the L.A.R. Service people left last time, they told me the problem was solved. It wasn’t. This is not normal. This is a lemon machine.Its one thing to have clothes destroyed, but what is extra frustrating is that I never know when the machine is going to destroy an article of clothing. This past Friday, we were preparing to go out of town for our daughter’s basketball tournament. I took the clothes out of the washer on Friday evening to discover that one of the blue uniforms was destroyed. There was no time to replace the uniform and my daughter was out of luck. This means that I cannot put an article of clothing into the washer that I absolutely have to have. I can’t live this way. This is a relatively new washer that should last 20 years. Right now, I can’t wash any important article of clothing. I’ve been told before that it was all set. Kitty has L.A.R. coming again this Wednesday to repair the machine. What am I supposed to do when it’s repaired? Put a uniform jersey in it? This is a very brief description of the experience I have had over the past 1.5 years with this new machine. The hours, money, disappointment, and utter frustration is more than I can describe in an email. I have attached three photos of recently destroyed items. Unfortunately, I threw away tens of items several months ago when L.A.R. fixed it.Is this unbelievable? Or are my expectations too high? Is this really what Maytag/Whirlpool has in mind for customer service? Is this really what they mean by standing behind their products? Why wouldn’t or why shouldn’t Maytag replace this machine? How much more time, money, and tears is a customer expected to spend and endure? How do I regain peace of mind and quality of running a household? Am I supposed to toss this machine and buy a new one? Believe me, that’s what I will have to do if I can’t get relief on this problem. There is no way that I can go many more months with this headache. In many ways, buying a brand new machine would be worth the peace of mind, but I am trying to make sure that my family, as consumers, are treated properly. It is also the principle of the thing. Please advise on any remedies available to me here in Massachusetts and please let me know what additional details should be provided and to whom.As an aside, Maytag/Whirlpool does not seem to be doing well with their reputation on the internet regarding customer service.

So far, so very good. This is the first time owning/using an electric oven. I just love my Maytag. It was affordable, especially since it was a combo sale with the over-head matching microwave from Home Depot. Two years later and it's as if I just purchased it. Wonderful, wonderful, wonderful.

We have been married 50 yrs. We have never had a Maytag, we bought one 4 days ago, Dec.13, 2017. This is the worst wash machine (Maytag Bravos XL MCT) we have ever had, the clothes come out wet with white soap marks on the dark clothes. Lowes said we can exchange it for another washer, it will not be a Maytag.

After one year, this famous Neptune washing machine began to sound so noisy during the spin cycle that neighbors must have thought a 747 was taking off from our house. After researching the web, I found that the main bearing always fails in this machine and there is a new one-man repair industry started up across the US to just replace these bearings. In fact, someone invented a bearing puller just for this problem. I am deeply disappointed that a once fine company would knowingly put out such trash. I am replacing ours with another brand, even though we have used Maytag for 30 years. Customers always determine who wins and who loses in the long run. Bye, Maytag!

The Bravos XL MCT Maytag commercial Technology is not a good machine. I noticed it within the first few weeks. I called Conns to request technical support but the technician they sent didnt solve the problem. I also called Maytag, they also sent a technician. He told me the same thing as the other guy. To use good quality detergent and to make sure the clothes are neatly arrange around the drums walls. Nothing works. My clothes dont get clean because they dont get wet. Theres lots of residuals and wrinkles all over them. Also, the machine takes way too long to finish a load of clothes. I did tried to return it, but Conns wouldnt take it back. I dont recommend this washing machine at all!

We purchased our Maytag 4000 series electric dryer in October 2011 from Best Buy. We did get a very good deal and have had little problems until this am. I moved laundry into the dryer and started it. While I was loading the washer, suddenly I heard a popping sound from the dryer and smelled smoke. Scared me looking into it. Sounds like either our electrical cord or our heating element blew. Coming from an era (born in the 1970s) where appliances should last at least 20 years, I am disappointed with Maytag. I shouldnt have problems at least until this thing is 10 years old. And even then I have higher expectations. So when I replace this, it will be with a better product.

Weve got a 3 year old dishwasher thats stopped working. First some of the lights on the control panel wouldnt light up, now only one light will light up and it wont start at all. Maytag would be better served to stick with the older mechanical switches and settings if it cant manufacture reliable electronic control panels.