I have had this refrigerator for three years and have ALREADY had two major repairs! I have paid ONE THIRD of the original cost in repairs. The latest was a control board at a cost of $225 and the repair man only charged me a service call and not labor because I was so upset. I called Maytag hoping they would at least pay for the part, but they only want to sell you a service contract (Of course it wont cover the control board, that already happened but would be happy to sell you a new extend warranty). I WILL NEVER BUY A MAYTAG APPLIANCE AGAIN! Run as fast as you can away from this brand. Be warned. They will not stand behind their appliances!

Bought a Maytag dishwasher model MDB7749AWM2 on 02 Jan 2012 with no issues whatsoever until three days ago when it stopped working altogether and after doing a series of tests I discovered that Im joining a large and growing list of owners with the same problem. I never have been a fan of digital controls due to their vulnerability to temperature and humidity conditions or high impacts for that matter. Ive owned many dishwashers of various brands for upwards of 10 years on average each. This is the first one not equipped with analog/mechanical controls. Im hoping I can still find more of that type.

We purchased the Maytag front loader Neptune washer and dryer set in 2006. Since then, the washer violently vibrates during the spin cycle - moving out of place and requiring me to move it manually. A certified Maytag technician came out to fix it and could not. The Maytag representative I spoke with said the circuit board is known to be defective and Maytag has not given any direction on how to fix, but that the board is irreparable at that time (in addition to the mold smell that emits from the washer despite the fixes for this). The old washers also used to have a coin receptacle so that any coins that were left in pockets went into the coin receptacle instead of into the pump area. This protected the pump assembly. But to cut costs, they took that coin receptacle out. This causes any coins or other possible things that fall out of the pocket to go into the pump area, getting lodged in there and requiring a costly replacement for the part in addition to costly labor. This washer does not do the best job in the spin cycle because it vibrates so much, leaving a lot of excess water in the clothes. I have also smelled a burning smell when doing loads that suggests there may be electrical issues that could cause a fire hazard. Then there is the dryer. The Maytag Neptune front load dryer has design issue with the electrical assembly. We smelled a burning smell and unplugged it. After taking apart the front cover, the heating coils had set on fire excess lint that had gotten into the heating assembly. In addition, the coil snapped in half, possibly causing a short in the wiring. This also caused other electrical issues that are causing more money to fix. In addition, this is the second time we have dealt with electrical issues with the dryer that have cost us over $400 to fix, including having to replace the drum because it was cracked. Lint and other items seems to get into the very important electrical areas of the dryer due to a faulty design in the lint tray, because the lint goes right through a hole into the areas where the heater coils are, which caused the burning smell in our dryer. In my opinion, both these machines could be very good machines if they were not made so cheaply and if they put good quality into the machines. They dont seem to be worth the price and the support is not there. Even more frustrating, the company does not stand behind the product, leading me to believe that they know about these problems, but dont want to fix them when they go bad. This can pose a hardship for families waiting for two weeks for parts while their dryers or washers are broken. Not to mention the enormous repair costs after the warranty has expired. Try to get them to replace something on the warranty and you have even more problems.

My Maytag dishwasher is not working after 1 years & 60 months. I called Sears, where I got it. Then, Maytag company. It looks like I need to spend $167 for an electronic controller (the push buttons will not turn on) if I do myself (I doubt if I can go it, but I can try). If not, how much will I pay a tech for coming (I was told $59) plus the labor if I let him fix it. So Im looking at a total of approx $400 plus to fix a 1 1/2 yr old Maytag dishwasher. Any comments Maytag??

I purchased my Bravos washer and dryer in about July of 2012. So far I have no complaints about the dryer but I hate the washing machine as do two friends of mine. My husband specifically wanted something energy efficient which is why we didnt purchase the basic traditional style washer weve always used. From the first time I used the washer, I was amazed and disappointed at the noise level. Because the lid is glass, I could observe the water level during each part of the laundry cycle. The water did not cover the laundry in the washer.When I mentioned this to one of my friends, she said that she has to wash some of her clothes twice. How is this energy efficient? I finally figured out that using the heavy duty wash cycle and heavy soil setting usually results in more water but requires an hour to wash and rinse the clothes. The downside is that the heavy duty cycle is too hard on some of my more delicate items so I have to hand wash many more clothes than I did with my old style washer that allowed me to select the water level I wanted. Most recently, when I washed a bulky mattress pad with a few other items, the water level never covered the pad because the load of laundry was so lightweight. At the end of the cycle, parts of the mattress pad were bone dry so I will have to take it to the laundromat if I cannot make the washing machine fill up with water high enough to cover the mattress pad. I dont want to spend the amount of time hand washing so much of my clothing, monitoring the water level in the washing machine and rewashing loads of laundry. After reading many of these comments, it appears that I have many more issues to look forward to. When this washer starts to break down, I will go back to an old style machine and a different brand.

We purchased our home five years ago. We bought a new Maytag oven and fridge/freezer. Within one year, the oven control went out. Then a few months later, the heating element went out. Within two years, our fridge/freezer went out. I purchased Maytag products because of the commercial where the Maytag repairman is doing nothing. I will never purchase a Maytag product again.

13 months after purchasing my Maytag dishwasher, it started operating by itself. I woke up one morning around 2:00 to it working, and I know I didnt put it on! I only use the auto clean cycle (that decides how dirty the dishes are, and is the cycle you use to conserve water). I dont use heat dry at all. Anyway, now I go to use the dishwasher and even though I press the auto clean button, the normal/heat dry/delay start buttons flash on. I try canceling this cycle out; sometimes it works, sometimes it doesnt. I dont see Maytag as reliable anymore.

My freezer has been leaking from the bottom for a few months and now the icemaker has quit working as well. The refrigerator has been purchased less than two years ago. The warranty is expired. I will not fix this refrigerator, as it is a gigantic piece of junk. However I would like to be compensated by Maytag at least 1/3 of the price so I can have it removed from my house before it creates more damage to my floors and subfloors.

2 years ago I purchased a Maytag Washer & Gas Dryer. Unfortunately, I did not invest or believe in extended warranties. I believe in trying to buy quality products. The door on the washer would not open and 2 error codes were displayed. I was trying to add another piece of laundry and the washer had just started. I canceled the load, waited for the door lock light to go out, but the door would not open. The error codes began displaying E3 and F5. I immediately went to the Maytag website for a resolution. The suggestions did not work and was instructed to obtain service if they did not. I called for a service call for $35, but was told that the repair would be over $300 for parts and that was not including labor. The parts I needed were a control panel and a part for the door lock. This was not a Maytag Company service tech and he told me that this happens because the parts are plastic. Currently, besides a Maytag Washer & Dryer I have a microwave, stove, and dishwasher that are also Maytag. When I replace these appliances, I WILL NEVER BUY ANOTHER MAYTAG PRODUCT. I expect the quality and life of an appliance to be more than 2 years, without buying an extended warranty. When I told a friend what had happened with my Maytag Washer, she told me that she had a Maytag Washer broke down with a control panel problem, and she couldnt remember the other part. She informed me that her repair was over $500.

You cannot go wrong with Maytag, even if there were issues they are reliable in repair, and parts are available so you arent forced to purchase new like some technology. I have been pleased with the front load washer dryer since 1998.

Also purchase the Maytag MMV405DS-1 over the stove microwave and in less than one year the light kept going out and the unit functions at no regular frequency. The unit is now out of warranty but service is coming to look at the problem again this week because we reported the problem within warranty. Maytag needs to be accountable for selling a lemon which I can only guess has a bad motherboard that they do not want to replace.

I bought a Maytag microwave in Feb of 16. Six months later, last August, it stopped working correctly (light doesnt come on, will not start, continually says open/close door to start). I have been trying for THREE MONTHS to have this fixed. Multiple calls to Maytag have resulted in nothing but empty promises. Calls to the store where we purchased it do no good - you have to call Maytag. We got 6 months use out of a Maytag microwave which we paid EXTRA to have installed. At this point I dont want it fixed. I want it replaced. The Maytag brand used to stand for durability and integrity; now it stands for badly made products and pathetic customer service. Look up my phone number on your computers, Maytag, and you will see all the efforts Ive made to get this fixed.

Brand new washing machine model MHW8200FW purchased at Karls, a Ferguson subsidiary, in Madison, NJ end of June, 2017. I wanted to buy a top of the line machine and this is what the sales person recommended to me. Problems started soon after purchase. Initially I contacted Maytag because the machine wouldnt spin dry a cotton bath mat weighing 4.5lbs soaking wet. I was told I should put more items in the machine to help balance it. Well there WERE more items and the machine wouldnt spin dry them either. I tried every trouble shooting Maytag suggested. Having exhausted my nerves, I called for service. The technician came and said these machines are extremely sensitive and that sometimes they wont even run an empty cycle. He said this is a common complaint with these units. One of his suggestions was to take bath mats, duvets, comforters... articles like that to a laundromat.I did less than 10 wash cycles after his visit when the washer started having more issues and finally broke down completely. The technician who came this time wrote a repair order indicating a mechanical (Stator) AND electrical (Control Panel) breakdown ($500+ for the parts alone if the unit wasnt under warranty). He also stated that he had never seen such problems in a brand new machine.I contacted Maytag for an exchange. Maytag customer service wrote to me that the breakdowns are ... normal, with all the units we sell some may have a defect in the first couple of months... and refused to exchange my defective unit. I can accept that there may be a defect that will warrant a repair, but in this case there are multiple defects in separate systems - mechanical and electrical - within the first month of service. This shouldnt warrant any further discussion, only a quick replacement and an apology.

Bought a new maytag gas range march 2013 model #mgr8674ab. The oven would not light at all. Would just click. Still under warranty. Called the service. They came and had to replace the controls in back. 2 months later the same thing, only this time it comes on and goes right back off. Then a week ago got it to light, used the oven and tried to turn it off and it would go off but immediately light up again. Scary to say the least. Another call to service. They are coming tomorrow. This is November 12 2013. I would not buy another maytag gas stove. There is something terribly wrong with this model.

On February 2006, I purchased a Maytag Quiet Series 300 Dishwasher and on July 2007, a motor leak. Maytag fixed it for free even though it was out of warranty. Thereafter (December 2008), the touch pad failed and I replaced it for $50. It is now August 2011, and that new touch pad is bad again, and this time, the part is $170. The Maytag will not run and the lighted display will not function from the start button. This was a $450 dishwasher that is now only five years old and useless.In all fairness to Maytag, their customer service is very good and willing to work with customers. Unfortunately, the product is very inferior in my opinion. To have stupid stuff like a control touch pad failing every three years is absurd and the replacement cost makes fixing it a bad investment.I will be going out this weekend and buying a brand-new inexpensive dishwasher that is on sale for $229. This model is not a Whirlpool product but it is a name brand.

Maytag gas range model #MGR8670XS 1 - I would not recommend this range. We bought it new and when I used the self clean oven, it did not work. It took four months to get this resolved. I self cleaned again, and I had to clean the oven by hand. It did not clean very well at all. I wish I had my old oven back.

A week after warranty expired, our 1 year old Maytag gas range (model# MGR7662WS 4) required new Direct Spark Ignitor (DSI) board. Knowing it was just beyond warranty, I inspected wiring first and found that the Bake connector on the DSI was loose, flopping around from a bad solder point on the board. Called Maytag and informed them of this manufacturers defect and all they offered was a $20 discount on a replacement part ($220 instead of $240). It worked with new part for 4 days, then something else went bad causing oven to spark, light, heat to less than 100 degrees, then shut down, then restart, then shut down, then restart, then stop doing anything. It has never worked correctly since then. How can a manufacturer of almost all domestic brands get away with such shoddy workmanship.. Taking advantage of defective or poor quality parts to sell more of the same when they fail and for an enormous markup? Where are the regulators who oversee monopolies and blatant scamming of American consumers?

This is the worse washer... As many other have complained I have the same problems. This washer it will not fill with water ever. It doesn’t rinse clothes or clean them as I’m use to the old washers doing. From day one I noticed the water does not fill in the tub and wondered how can the clothes be getting cleaned properly. Getting a F51 code and after going on YouTube and checking for problems it seems to say the same code after it works for a bit. This is the worse appliance I have ever purchased. I am so frustrated and will never purchase a Maytag anything again. Never did in the past up to this one and never will after this one.

I spoke with Mike today at the customer service department at Maytag to see if Maytag would pay for the parts to repair my 04/2010 Maytag front load washer (model MHWE450WW00). The bearing assembly needs to be replaced. So, that means the tub and basket need to be replaced too. The original cost in 04/2010 was $1,088 plus tax. The cost to repair is $1,048. Maytag will do nothing since it was purchased over 12 months ago. I cant believe I just threw almost $1100 away on a washer. Obviously, there is something wrong when an appliance doesnt work after 1.5 years.

I bought the Maytag Bravos because I was told it was top of the line and expected that Maytags reputation for quality would provide me with many years of dependable service without problem. Boy, was I taken for a ride! Unless you have a lot of money to spend, DO NOT buy a Maytag Bravos washing machine. After only 3.5 years of normal use (3-4 standard loads per week) and doing everything as suggested by the owners manual, my machine has developed a bad drum bearing. The cost to repair this bearing is $400 for parts and $200 for labor. In other words, I am forced to buy a new machine after ONLY 3.5 years of use. When I called Maytag customer service department to question them about my problem, their response was there are no recalls on your machine, so we cannot do anything for you. When I further questioned them about the lack of quality/dependability my machine provided, they again said, Sorry, the machine is out of the warranty period. Thank you for buying Maytag. If you buy one of these washing machines, you better have the extra money to buy an extended warranty.

Dryer delivered nonfunctional. Tech showed up the following Tuesday. Diagnosis main board and one sensor dead. Tech returns following Thursday. Replacement board DOA. New dryer still nonfunctional. Awaiting new board with no functional $1100 dryer. This dryer replaced my three year old Maximus which was deemed too expensive to repair after three repairs. Please do not buy a Maytag/Whirlpool product.

I depend on my front loading Maytag washer. It is very reliable, does a great job of cleaning even difficult items like comforters and pillows as well as items deeply soiled. I use the many features like water temp and level, fabric type, heavy or light load, etc. The only complaint I have is that the front cover of the detergent, fabric softener and bleach drawer came off and the exterior paint on top of appliance is rusting and peeling. A stronger substance for the surface where often detergent, fabric softener and other substances are often stored and they leak.

We purchased both a new Maytag washer & dryer in 2011. Our dryer, Model #7000XG1 all of the sudden started thumping when we were drying our laundry. After we called a technician to come out, he stated we had a crack in our drum. How in the heck does that happen in 4 years time and only laundering for 2 people? Of course this steel drum should not wear out before the other parts, but it did. Since there is a backorder on the replacement drum, it makes you wonder if this problem is wider than it seems. Also, Maytag would do nothing for us other than offer us the purchase of a new dryer at a discounted rate good for only 7 days of their offer. Seriously, how about standing behind your product? And, then again, why would we be enticed to spend that kind of money on the same type of product that has flaws? Uh, duh Maytag or Whirlpool. Silly fools you are.

I purchased a Maytag Centennial MVWC360AW washing machine on July 11, 2013 at The Home Depot. I assumed that I was getting a good product based on my Moms old Maytag washer. This machine is the farthest thing from quality that I have ever experienced. My Mom would roll over in her grave if she knew how CHEAP Whirlpool has built---what is supposed to be a---Maytag! The machine worked fairly well, at first. Even though I didnt like the low water arrangement. I like clothes to be fully immersed in water! That went on for 2 years and 5 months, until NOW the led light goes to Rinse, but it wont agitate. Then the led light goes toSpin, but it wont spin! I called a local appliance repairman and he told me that the control is bad. They cost about $250.00. Its not worth repairing!! So, Im stuck with this piece of junk! Shame on Maytag/Whirlpool for building a PIECE OF JUNK!

About 9 yrs ago, we remodeled our house. And when it came to appliances, I was vehement we were going to go with Maytag because of their great name and reliability (We have 7 sons and needed reliable appliances). Boy, was I ever wrong?! We have gone through 2 Maytag dishwashers and countless repairs to the Maytag dryer. And our top of the line refrigerator has been a piece of junk!Of course, shortly after the year warranty was up, the flimsy pieces of plastic holding up the shelves started breaking off. The repairman, who came to replace the cooling coil on the refrigerator, said those shelf plugs couldnt be fixed. The whole front of all drawers have come off as well. He mentioned that Maytag was going bankrupt and started compromising on fit and finish. And he said that we just happened to purchase in that time frame. Now, we have a compressor that needs to be replaced for over $500! I have, in my garage, a Gibson freezer from my grandma that is 40 yrs old, and literally the most reliable appliance we have. Never have we made any repairs to it!I called Whirlpool (since they bought Maytag) to tell about my horrible experience with Maytag, and let them know we have to replace these appliances. I asked if there was anything they could/would do (discounts whatever) to redeem their name. I was told that they would not be able to help at all. So, I told them that I would not give Whirlpool anymore of my business and warn anyone I could, not to buy Maytag, Whirlpool or Amana. Isnt there any appliance company out there who cares about customer service, a good name and a reliable product?!

This washer ( MHW3505FW) leaks, is crazy loud, water wont drain, clothes smell bad after washing, defective drain pump, defective mother board. Only had 2 1/2 months and it broke. Maytag refused to refund me and Lowes refused as well. Thankfully I paid by credit card. Am disputing the charge. Terrible washer should be recalled. Many complaints on this washer. Very disappointed and upset.

We purchased a brand new Maytag washer dryer and had nothing but problems with both. After talking with corporate several times, trying to reach the CEO, the customer service person told us that the problems were buyers remorse. Needless to say we will never purchase another Maytag/Whirlpool product as long as we live. We are going with Electrolux!

A lot of repairs in 6 years from belts. It leaks water around seal on door. Only part of the cycles work. I would not recommend the Maytag washer to anyone. When I got it I expected or hoped it would last 10 years or more.

Product number MMV4205DS. Beautiful, felt solid. Right away when we would put in a time to cook and hit start, the thing would say Open Close Door. First we thought it was moisture, and we would wipe the seal, then lifting the door a little helped. A month might go by and we would repeat this process. I did a little research and found the microwave is known for this. After the warranty was up, it got worse. My husband put a little screwdriver in the door clamp. The plastic guard that held the door shut fell behind the opening. Mulling over whether to call for repairs or buy a new one, we decided the latter. I am buying another one just like it, because the holes in the wall will match for an easy swap and it matches my suite. This time I took out the 3 year warranty, which I will hold Maytag responsible for any more problems. They say if they come and fix it 4 times in a year they will declare it a lemon and replace. I figure this will work in my favor because the microwave lasts a year!

The freezer leaks water onto the floor in large pools. Had it repaired, two weeks later, still leaks. Very unhappy with the performance of the bottom freezer Maytag refrigerator.

I, too, have had a lousy experience with this washer – it does not correctly sense the amount of clothing in the load, and often fails to get everything wet. Once the cycle starts, it does not necessarily pull everything into the water. You must ball each item up around the center or have sleeves and legs of clothing end up very twisted. Clothing is often very wrinkled and I do not feel that enough water is used to achieve clean clothes. I did get a good response from Maytag, who sent a repairman free of charge after the one year warranty period. He was very gruff and condescending – implying that I am buying the wrong kind of clothing. He reset the washer which improved the water levels, but now it is back to its old tricks. Hate, hate, hate this washer. Now it is failing to start unless lid is slammed shut! May get a new one in a black Friday deal, but have to figure out how to ditch this one while retaining my integrity/honesty to buyer.

I have a Maytag microwave and stove in my condo kitchen. Both are about 4 years old. Ill never buy another Maytag appliance again. This stove had problems from day 1 and the support was dismal. I had [bought] an extended warranty, which covered nothing (I let it expire and didnt renew). The microwave handle came off in my hand a few months ago. I stuck it back on with gorilla glue. Now it is starting to shut itself off, as if it lost power then mysteriously turn itself back on. Im sure there will be a new microwave in my future and it wont be a Maytag.

We purchased a Maytag Bravos X washer 2 years ago. Theres not enough water in there, and the clothes get so tangled that Ive had holes in them. Ive had technicians come out several times and they just say that its the water saving feature of the washer. I put it on the wrinkle control setting and the clothes come out ridiculously wrinkled. All of these problems are due to the water saving feature. I absolutely hate this washer and would never recommend it. I want my old washer back with the agitator and enough water in there to actually wash clothes.

We bought this washing machine 2 years ago and I was never really satisfied with how it cleaned the clothes. Darker pants would come out with white soap/water lines on them. The worst part, 2 years in, the washer basket seal failed and the bearings rusted. The washer sounds like a tornado every time it runs. I got a quote for $350 to repair it!

As others have stated, cant wash more than a couple towels or 2 pair of blue jeans. The washer is useless. Purchased Maytag for quality and received crappy worthless machine. Maytag should take returns and refund buyers money!

At first my dishwasher worked great and I have always been really good about rinsing my dishes before I put them in. Starting a few months back I noticed my dishes were coming out gritty then all of a sudden it started backing up into our sink.

Maytag Centennial Washer MVWC400XW2 - Bought this washer Fall 2011 -- first 6 months had to be serviced and now (February 2016) needs to be serviced again - has not cleaned my clothes for the last 3 months. Now, I have had to order a new washer - you can bet it wasnt a Maytag. My new washer will not be delivered for another 3 weeks. Past the part of not cleaning clothes, now it wont even empty the water, or pump out the water. It makes a horrible noise! Before it wouldnt use any water, now, it fills completely up. I do not know if it will make it through this current load much less another 3 weeks. Always bought Maytag before BUT WILL NOT AGAIN - after what I have been through with this washer!

We bought a Maytag dishwasher 4 years ago, we had to have it serviced a few months after purchase for the soap & rinse agent dispenser not working, then a few months after warranty was up the buttons on machine wouldnt work, the control panel failed so we had to pay for a new one and install it... Well last night exactly one year from the install of the new control panel I walked into my kitchen to find it full of smoke and the dishwasher pour out smoke, when my husband came home he took the door off and sure enough the control panel was burnt and melted! Very scary. It is a very good thing I was home and this is why I never leave appliances running if I am not home.

I bought a every expensive Maytag Neptune (washer and dryer one unit) and it is now sitting in the carport. The washer broke and I had to have service people come to my house continuously. Over a period of 6 months I had to pay for 3 motor control boards plus service calls. Thats when I had I moved to the carport. In 2012 I bought a Whirlpool Duet washer and dryer so I would be able to stack them. I had to put them at Sears because I had to use layaway. I paid for them over 12 weeks and had to use a laundromat during that time. Last week I got a F01 E02 error code which means replace motor control board. These boards cost over $300 each not counting the cost to install it.I did talk to Sears since the washer was only bought 4 years ago. They were nice to me but could do anything for me. Truly sad when a washer only lasts 4 years for the amount of money I had to pay to purchase it. I dont know what I going to do now since I am now retired but I WILL NEVER BUY A WHIRLPOOL OR MAYTAG AGAIN.

Its a shame that I bought into the Maytag equals quality and customer service falsehood. Same problem as the others on this site and undoubtedly thousands of other consumers that bought a similar refrigerator freezer combo only to discover puddles in front of the unit and a 1 thick slab of ice under the freezer drawer. I contacted Maytag parts and when I described the issue he transferred me to warranty. The warranty department acknowledged this was a known problem and they would supply the part, no charge for the part but I would have to pay the serviceman to install it. They would not however, send the part to me to install. The unit is out of warranty, of course it develop the problem until right after the warranty expired. I plan to examine the drip pan and figure out how to improve on the design myself. I will not replace any appliances with Maytag, Whirlpool, Kenmore, or any other major appliances from this group of companies... Beware!

Washer was delivered Feb 2016. (First one delivered Jan 2016 with damage.) Home Depot HEAVILY promoted this model - we paid $600+. This washer has NEVER thoroughly cleaned clothes & now does not drain completely!!! Theres always lines of dirt left on clothes - you can see dirt clearly on dark clothes. Washer does NOT fill with enough water to thoroughly wet clothes! (Even on the bedding, extra dirty settings!) Clothes smell clean because the detergent was not washed or rinsed out. Washer does not agitate, turn over or rotate clothes... It gently shakes the tub side-to-side (like a mild earthquake does the ground) which does NOT move clothes around. Home Depot salesman said it strongly rocks clothes turning them around and under. It does not do that! You have to stop washer and PHYSICALLY move clothes from center and turn them around so bottom of pile gets wet (Now I understand why this model has a see-through lid!!!) This model is supposed to pre-wash sense the load amount by shaking the tub side-to-side to gauge how much water is need - FALSE ADVERTISING! I put gallons of water in two loads (same bulk & weight of clothes) to see if more water would be used on the heavier load - results: the same amount of water was used on both loads. Now (Oct 2016) the washer is not draining completely and going back to wash instead of rinse, drain! Maytag Corporation just says theyll send a repair person out but this is a SMALL town & the repair shops theyll use here are sketchy!This Washer is a huge waste of money just to own laundry status tone bells & non-usable settings. Its probably in violation of OSHA health/safety codes because if there are chemicals, feces (sorry, but wheres theres kids...), blood, diseases (if you visit anyone in a hospital), etc on the clothes... Those things are NOT being washed out of the clothes, so youre being infected by touching improperly washed clothes. WHY is there not a RECALL for this appliance? There are many, many people having the SAME problems as us. This is our first HE top-loader and I wish I could afford to get rid of this & buy a washer with an agitator... But alas, we still owe $300 on this worthless (albeit fancy-looking) appliance. :( Maytag XL HE top load Washer MVWB835DW (Does NOT clean clothes!)

I bought a Maytag washer (Centennial) because of its reputation. I didnt even realize this site was out here and would have made another selection had I known. I bought the washer on June 7th of 2011. On June 15, 2012, the washer just quit working. I called Maytag. They said since the warranty was over that I had to pay a technician to come out and it would cost $129. I was upset but I had to have a washer so I scheduled it. The tech came out and said the motherboard was bad. He said that this has been a common problem with this machine and that Maytag should actually recall the part. The replacement part was much better. He suggested I call and complain. The part was $180. He said that Maytag may reimburse me because it was so close to the warranty cut off. I called Maytag to explain the situation, and what do you think their response was? Since you already paid for it, there isnt anything we can do. Nice! What a joke. I will never buy another product from them and neither should anyone else.

My model has 2 ovens which I love. A smaller one & a regular sized one. It also has a cooktop. The cooktop always has “marks” on it from the pots & pans. No matter how careful we are, the pots leave marks. We even bought new pots & they leave marks. Something that we do like is that 2 of the burners have “select a size” so these burners can be used for small or larger pots.

Please read Michael of Davenports review. I read it and word for word this is my experience. This washer is the worst Ive ever had. If I could get back my old 20 year old machine, I would trade it in. Dont buy, youll hate it.

A refrigerator has to keep your food at constant temperature. The first Maytag refrigerator I purchased from Home Depot could not get cold. I mean the refrigerator never got below 65 degrees. I called Maytag and they played dumb. Just wait weeks for a repairman to check a brand new product that is not working. Home Depot replaced it in few days with another refrigerator of the same model. It runs but doesnt get really cold (it only has a fan in the freezer and the air comes down from the freezer to cool the refrigerator). I live with it because all you will get out of Maytag/Whirlpool is to turn the dial to a colder temp. A little over a year passes and the fan in the freezer just stops running. I called a local certified service person. He looks at the fan and says that its running but barely. I had to replace the motor at cost with labor of around 200 dollars. I kept the motor. Turns out the motor is made by Panasonic. The current replacement motor is made in Mexico. Now the refrigerator runs cold. Since I had two of these refrigerators that failed to get/stay cold, I think they got a bad batch of motors. Maytag response was to refuse to pay a dime, it is outside of the warranty - even though I had called about the refrigerator not getting real cold on the second refrigerator. So basically I lived with food being kept at a way too high of temp causing spoilage for a year and Maytag/Whirlpool could care less, they are only worried about their bottom line.That is not the only problem with their product. The drain pan grows a mold that looks like pudding. The only way to clean it is to pull the refrigerator out, take off the motor area cover (which is really cheap cardboard) and clean it out with a rag. There is no way to remove the pan. The compressor is mounted so low that it heats up the floor. I have concrete floors thus I have no fire risk but if you have wood floors, I would check the heat level. It is nearly impossible to clean the dust off the fins on the refrigerator coolant lines. The back of the freezer door shelves are metal and very sharp on the back. Thus if you stick your hand in to pick something up, you will get a nasty cut.I have owned only Maytag, Whirlpool and Amana products my entire life. I will never purchase their products again. They may pretend that you are buying an American product (they use the American flag) but this product is nothing but OEM garbage made by the lowest bidder. They try to sell you an extended warranty for around 300 bucks for an addition 3 years. I figured if the fridge went bad after 3 years, I would just buy a new one. I never expected a motor to fail less than a year (I would say it started going bad about 6 months into ownership as started making ice at a lower rate). Maytag refuses to stand behind their products. When I told them I had the motor that failed, they had no interest in even looking at it. Do not waste your money on their products. I also own a Maytag washer that is the worst washer I have ever owned.

This Maytag was installed in this house in the summer of 1984 and washed dishes for my in-laws for 26 years. We moved in as a family of four and this Maytag dishwasher is still washing the dishes clean. No rinsing, just make sure the food is gone. We replaced the belt about 6 years ago and I think my Mother-in-law replaced the door seal. It has a power saver button, 2 cycles, and the cups are on the bottom rack, plates and such on the top. I dont put plastic bowls on the bottom because it gets a bit too warm for them but all the bells and whistles still work. It is a fairly large model, WU301, with ample room for plates and platters. I dont wash pots because I dont like what the dishwasher soap does to the finish on them. Having the cups on the bottom is nice and the rack is very usable for other dishes as well. The cutlery rack is located on the top rack, removable and a decent size. Almond body, silver and dark brown accents, very 1984 but not a bad look. All of the buttons and knobs are easy to read and use. Maytag, 1984, model #WU301.

I bought a refrig from Home Depot on 10-16-2012 two years ago and it doesnt work, but they only put one year warranty on. So had to go out and buy another. My complaint a refrig should last more than two years but they were going to send repairman out on my expense and more than likely would of cost me the price of a new one.

Clothes are never submerged in water. Clothes come out worse than when they went in. Every review and complaint mentioned is dead on! This Bravos XL is a piece of crap. Stay away from lying salesmen from HH Gregg. And stay away from Maytag. Perhaps we should all get together and file a class action lawsuit! And donate all monies, washing machines and dingy clothes to charity!

I purchased the Maytag oven in January and have had the service technician out 5 times to try to repair the oven because it doesnt heat properly. Theyve told me that because I live in a condominium that it is normal for the oven to take an hour to preheat, then another hour for the second oven to preheat. When I am baking the oven does not hold the temperature and anything I bake takes much longer than it should. They refuse to get me a new oven.

Shortly after having this appliance custom wired and installed into the kitchen cabinets above our gas range, we found that the microwave no longer worked. The window where the digital clock shows the time instead Showed SE. I hit the clear button and the microwave once again worked. This happened again on many occasions and the clear button corrected this malfunction. Now this has happened once again but nothing Ive attempted clears the System Error or reboots the microwaves brain. Ive contacted many appliance repairmen but as soon as I mention Maytag they inform me not to repair the microwave as it costs more to repair than to replace. Ive attempted to purchase a new circuit board and repair it myself but no one has the part available. This appliance was purchased in April, 2009. Can anyone recommend a Microwave Brand as a replacement for this disappointment?

I just bought a brand new Maytag microwave a few weeks ago. The door is already broken! I’ve been sitting here 4 hours! waiting for a repairman man. No call, no show! I am missing work and gym time because MAYTAG sold me a faulty microwave in the first place! Never again will I buy Maytag products!

We bought our refrigerator 14 months ago and it has a 10 yr limited parts warranty. Both the freezer and refrigerator quit working, right after we spent $600 in groceries. I called the warranty dept and the soonest they could get here to service it, was 9 days later cause they only go thru Diamond Preferred, to do the repairs. Then on the 9th day, Diamond Preferred calls to let us know that unfortunately, they cant get here to fix it until another 5 DAYS!! Two weeks with NO refrigerator and freezer, is ridiculous. They should pay another repair place to come out instead of just relying on the ONE!! Our food is now ruined, $600 worth. And to top it off, weve had to eat out costing us more money, and then once its finally fixed, we have to go buy more groceries. I will NEVER buy a Maytag appliance, ever again!

In the past 20 years, we purchased a washer, dryer, stove and dishwasher... all Maytag. The washer (purchased 20 years ago) is still functioning well! The other three appliances have all given us trouble and the dryer is no longer with us. Our stainless stove is LOVELY but thats about all its good for. Within 12 months, one of the burners burned out... just beyond its warranty. It has two ovens and 3 years after purchase, neither will hold a constant oven temp and both take an eternity to warm up... although the digital temp on the oven tells me its toasty warm. Recently, the dishwashers control panel wont set properly. An attempt to set it for a normal wash/dry cycle results in rinse only and a 2 hour delay. Make them like you used to, Maytag! Im no longer a customer!!!

Washer water level sucks low at max levels kept freezing. Bought mtw7230. Its junk agitator doesnt rub good. Not like dual action agitator and when I start cycle says 34 min but I timed it takes one hour. Same goes to 1:30 to 2 hours takes 10 min for water to pour in spins for nothing. I sent it back. 965 I paid.

It’s washing day today, so I’m angry, frustrated and livid to do it in my Maytag machines. I’m 72 years old and been doing this for 53 years. It’s not a job you love to do but you do it. I finally get to be able to afford whatever machines I want, so what do I do, buy Maytag. They are beautiful, see through top load, and see through dryer. So finally I get to use them, what a letdown. I don’t understand how they can put these machines on the market. Unbelievable! Also very expensive. The sensor for the water level is way off. It starts washing with hardly no water covering the clothes so this is where I put it on pause and add buckets of water to wet at least the clothing. I did a test to see how the clothes moved inside when washing. It was a load of white towels and I put in a bright green face cloth to see how it moved around in there. Well what a surprise, it stayed on top and moved about 3 inches to the right. That’s all it did. You don’t call that washing, I call that soaking! Terrible washer! I could go on and on but I’m getting too upset. Now for the dryer, the sensors don’t work right so what I do is use the timer and the temperature buttons only. Sometimes clothes gets stuck under the lint basket and by the time the buzzer tells me the load is finished drying, it is so twisted that it’s wrinkled forever. It has ruined a beautiful tablecloth of mine. I can’t sell these machines because I would feel very bad to pass them to someone else…Maytag does but not me. Because of my age I won’t be getting new machines probably, I’m stuck with them, but I would advise anyone shopping for a new washer and dryer, go out there and see what they have, come back home and look for reviews which I did not. Bad mistake! Note: I searched everywhere to write this review to Maytag on their website, none to be found!

I also have water building up on bottom of freezer drawer. It turns into ice and if I dont clean it out in time, it leaks onto my hardwood. I am very disappointed that Maytag has not reached out to its customers to resolve. My fridge is only a few years old and its frustrating taking the ice out of the bottom. I dont have the funds to have it fixed. I thought I was buying a reputable Maytag fridge! IF there is any class action suit please let me know.

I bought a Maytag refrigerator, model MBF 2256 KEQ2, two and a half years ago. Now the cooling coils are freezing up. I checked heater and thermostat for continuity and they were okay so the only thing left was the timer control circuit. On the earlier models, the timer control circuit is controlled by a Timer Motor or an Adaptive Defrost Timer which is separate from the main Electronic Control Board and much less expensive. On later models (including mine), the timer control circuit is incorporated into the main Electronic Control Board so if your automatic defrost quits working, more than likely you will have to replace the main board. I did not purchase an extended warranty because I believe they are useless from past experience. I bought the part on Amazon.com, received it in four days and replaced it myself for a cost of $78. This part costs $110 to $118 at Sears or a Maytag dealer.

I bought my Bravos XL 3 years ago after having older model Maytags since the 1980s. My mother also runs a laundromat and SWEARS by Maytag. To say Im disappointed in this purchase is an understatement!!! They have never washed the same as the older models. They twist the clothes horribly! Now Im having issues with all of my dark clothes getting grease spots on them with no apparent cause. I use HE detergent and softener (recommended amounts only) and clean the washer religiously, including the detergent, bleach and softener cups. I DETEST these machines. Also, the dryer never dries unless I run it for 2 cycles, regardless of what setting it is on. Waste of money and definitely not energy efficient when it comes to my water and electric bill, nor time efficient for me since clothes either come out still dirty or with new stains. After this purchase, I would NEVER buy Maytag again!!!!!!

The paint (stainless steel) on the top panel surrounding the digital screen is deteriorating from the heat and steam from light cooking. This happened the first time I used one of the back burners for light simmering. I purchased the range in December 2011, but had not used the back burners because I dont cook large meals. The black paint on the range top is also easily scratched when moving the grates for cleaning. This product has defective paint and Maytag has NOT responded to my questions sent to them by email. I will never purchase another Maytag product NOR will I purchase appliances from HOME DEPOT again. Home Depot should not sell shoddy products!

My refrigerator was delivered on April 3, 2016. I began calling for service July 2 when the bottom freezer door started depositing ice chunks on my kitchen floor every time we opened it. An appointment for service was made for July 18, service never showed up. Another appointment for August 3 was made and again service never came. I called the 800 number on Aug 19 again arranged service for Aug 24 after hours so that we did not have to take anymore time off work. When repair finally looked at the fridge they said the door was not aligned and did not close so the frost builds up and breaks off onto the floor. This can be fixed with a new door that can take from 6 weeks to 8 months as they are not stocked and have to be made at a factory. The fridge constantly runs and is starting to leak water through to my kitchen floor and basement ceiling tiles.I called Maytag/Whirlpool on Aug 25 and the service agent told me the best they could do for me was extend my original warrant by 6 months while I wait for replacement part and they advised I purchase the extended warranty. The second agent named Gabby I spoke to advised me to call Home Depot where I purchased the fridge to see if they would do something for me. She would write down my concerns but had nothing more to say or do for me since the repair person deemed the unit repairable and a part has been ordered. I called Home Depot on Aug 25 and I spoke to Appliance Dept who told me the manager who could help me was off that day. He advised me to stick weather stripping around the door to seal the leaks. I said I was hesitant to do anything that may void a warranty and he agreed. He suggested I may get a loaner fridge but I have heard nothing yet. I want a replacement fridge.When you pay $2000 for a fridge it should be worry free for at least a year? I have been reading reviews and I am wondering why this is not a recalled appliance as this seems to be a very common problem. I am sad that Whirlpool is not standing behind this product. Home Depot has been in touch with me regarding this fridge issue and the lack of customer service provided by Maytag. They are replacing the fridge on Sept 9th 2016 and taking the old unit away. Home Depot has tried to get in touch with Maytag and they have not gotten a response at all about my faulty unit.The staff at Home Depot in Peterborough have been excellent to speak to and have apologized for the issues with getting service to my appliance. I am very grateful to them for their assistance and for following up with me in this matter. The downside is that I am getting another exact Maytag unit as a replacement so hopefully this does not start all over again. Home Depot has been a great retailer to deal with. I am very saddened to hear that even Home Depot cannot get responses from this manufacturer. I have also lodged a complaint with the Better Business Bureau.

I changed from another HE brand to this model. No comparison. This machine can do twice the work... but double the time. My former machine was quiet while this one is not. Maybe I got spoiled to the former brand, but Ive never heard so much noise from a washing machine! Ive always thought Maytag meant quality but I think they may have missed the boat here. I tried reviewing on their site but when I gave it two stars, I got an error message. Clever, Maytag.

I owned an front loading Maytag Neptune Front Load Washer MAH5500 for more than 10 years and first 5 yrs doing 2-3 loads a day for a family of 12 so this machine held up well, and only issue we had with the machine was the rubber around outside needed to be replaced after about 9 yrs.

Called to schedule service for letters on door to be replaced ice and water completely rubbed off until you didnt know which one you were getting. Refrigerator is less than 10 months old. Also freezer door was hung lower than refrigerator door. Was told nothing could be done. It was a cosmetic issue. Very rude customer service dept and I talked to two separate people and they were both rude and unwilling to help. I can promise you I will never buy any of their appliances again.

This Maytag dishwasher was purchased because Maytag has always been represented as a reliable brand. Wish I had done some research on this problem before repairing it! The control panel went bad after 18 months (and at least 6 months of this time it was not used at all!). The repair cost $300, the dishwasher only cost $429, and if I had realized how much this would cost I would have bought another dishwasher instead. Wonder how long this control panel will last? I called Maytag to complain and was told by Dana badge no. ** that there was nothing to be done as it was out of warranty. We have had dishwashers for 10+ years before that never gave us any trouble. I told her I wanted to speak to her supervisor and she told me she didnt have one! Really, how about if George Moore the CFO or Arthur Learmonth the President call me back on this one! We shall see what they say, but I can see by all the complaints about the same issue with Maytag dishwashers that we will probably be out of luck unless we start or join a class action lawsuit (looks like there is one in California already). I will amend this post if Maytag decides to stand by their product and at least pay for the cost of the control panel, but Im not holding my breath.

First off, everyone seeing this should be fuming as I am because we are mostly in the same boat with these control panel issues. Mine is Maytag model MDB7749SBM3 about 575.00. A little bit cheaper than most of you because I purchased at the online and had a rebate. About a couple months after the warranty expired, we started having weird light issues with the control panel where are one light would pop up when you didnt hit it or other lights would pop up when you hit something else. We kept dealing with it thinking that it would dry out and resolve itself. Lo and behold, just like it appears to be tens of thousands perhaps hundreds of thousands of machines, it quit. I read this consumer affairs post after it quit and now I know why it did. I opened up the control panel and sure enough, the little ribbon that connects all the electrical connections had brown on the back like it was burnt through. I was able to find a special 1 800 number that Whirlpool has set up because they have purchased Maytag and the woman I spoke with said they would send a technician out and that I was responsible for the diagnostic fee. I was born but it wasnt yesterday. I immediately said to the woman, Absolutely unacceptable. I am NOT paying for anything, very politely highlighting the fact that I know they settled a class action lawsuit in California regarding a control panel issue and there are hundreds maybe thousands of complaints on consumer affairs.com. The woman place me on hold, I am assuming to speak with her supervisor and then let me know that they would pay for the diagnostic fee. She said a repair date for me for about a week and a half later. The repairman had a good day because the dishwasher was already disassembled for him and he proceeded to take pictures and call Maytag. Maytag told him that I was responsible for the installation cost and service fee which according to the technician is about a hundred bucks. I told the technician that is fine but it will not be fine when I call Maytag back. I have not spoken to Maytag about the hundred dollars needs to file a claim for a new dishwasher and associated damages. I have not spoken to Maytag about the hundred dollars but I am only on this to let you know that every single one of us needs to file a claim for a new dishwasher in associated damages in small claims court. I plan on filing a claim for approximately $700 for a new dishwasher and damages. In my opinion, I feel like we should all do this, otherwise big corporations like this will continue to shovel garbage into the stores left and right.Have a good day and good luck with your court case hopefully. With all the evidence against them, I have a feeling that they will settle this and pay before the court date even comes around. Good luck to all of you. I will try and update this after I call Maytag back for the hundred dollars that they are going to charge to repair their broken part.

Purchased a Maytag refrigerator on 08/15/13 model #M1TXEGMYQ01. Started having cold problems 06/15/15, called company. 1 yr warranty expired 08/15/14,had to replace a 22-month ref on 07/15/15. Prior I owned a Hotpoint that lasted for 17 yrs and the last one was a GE that lasted for 18 years.

Im not sure that the guys who designed this unit ever actually tested it. During the wash cycle, if you have something like a fitted sheet it will actually stuff all of the surrounding wash items into the sheet until it forms one huge, round ball. Then it gets really interesting because the vicious spin cycle sends the machine marching around the laundry room and this happens even if the wash has not balled up. I now try to evenly distribute the wash within the tub prior to starting the wash cycle but it doesnt work. So now I grab a cup of coffee and newspaper and sit with my washer throughout the entire spin cycle to make sure that the hoses dont tear out of the wall.

I like most others have experienced the same issues with the new Maytag top load WM. In addition my new machine dances across the floor like a drunk leprechaun. After Lowes told me that with my extended warranty Id have to miss work and pay 100 bucks for a service call I emailed Maytag. Needless to say they didnt even respond. Ive have learned a few valuable lessons. Dont assume that more money means better merchandise. Made in America doesnt say much. And please dont buy Maytag.

We purchased a new Maytag dishwasher last year when we purchased our new home. All the other appliances were Whirlpool. This dishwasher runs forever. We have huge electric bills and I am sure this is a contributing factor. We purchased it from Lowes. They have sent out two technicians who say there is nothing wrong with it. One said it was because it was in an island. The other that our water is not hot enough. He turned the water heat up and now you have to warn people using it to be careful or they will get burned. No wonder the Maytag repairman is so bored. He knows the appliances he services are junk and doesnt bother. Take my advice. Buy ANYTHING BUT Maytag!

I was always impressed with the front loading spin washers commonly found in laundromats. The top loading Maytag Bravos does a great job of cleaning clothes and does not stick another door in your way when loading or unloading it.

I bought a Maytag side by side fridge freezer in 2010 at a cost of £2000. Having come back from a week away it had entirely defrosted spoiling all the contents. An engineer came to look at it but said the fault was unrepairable so he wrote it off. Maytag (Whirlpool) think that it is perfectly ok for a 5 year old fridge freezer costing two grand should now pack up. I, on the other hand, do not... They offered me £700 of the cost of a new Maytag. Joy! I thought. However, this one does not make ice or have chilled water (the principal reason for buying Maytag in the first place). I was then told that this was the ONLY fridge freezer in the entire Maytag or Whirlpool range. Is there nothing else you can do to help? I pleaded. No was the reply. The moral of this story is going posh on an American Fridge freezer is not guarantee that you will get the after sales service that the price would suggest.

I do not like this Maytag Centennial Washer at all, I have had it for a year and a half and it just does not perform good at all. Most of the time the clothes still come out with dirt on them but what I am most mad about is the fact that it keeps leaving bleach spots on my clothes, several washes after I use the bleach. I will definitely not recommend this washer to anyone.

This is the worst washing machine I have ever had in my life. Machine started bouncing during the wash cycle and also the spin stopped. Never in my life have I had a machine fail on me like this one. I spent a lot of money on this. This machine should be recalled. I read up on all the complaints. Its a model #Tw6600TQ0.

Almost 2 years ago this dishwasher wouldnt drain. Fixed that $300. Then just over a year ago control panel had to be replaced. Now control panel was bad again, had to rest circuit to get it to start. I see this is a common problem. Only 2 of us in the house and the dishwasher gets used only 2-3 times a week since we purchased brand new in December 2011. Ordered the new control panel and just went to replace it, guess what. This appliance could have burnt our house down. The wiring in the door that plugs into the control panel is burnt! Not at the panel at all but a good 8 down the wiring harness. Both harnesses as well. Scared me half to death! To think it could have killed us at night, when we usually run this appliance. Definitely calling Maytag now. I do have pictures as well.

I purchased Maytag microwave model MMV4205AAQ in 2005. I use it infrequently. It stopped heating in Nov. 2011. It must be replaced. But after this experience and reading other comments, I will not purchase any Maytag appliances in the future.

First of all, the hoses that came with my washer leaked and were cheap made. My husband put the hoses from my old washing machine on the Maytag. Then, I hadnt had my Maytag washing machine but about two months when I had a problem with the mixer. I had to turn the hot water connection off in order to wash in cold water. When I called the store to explain the situation and ask if they had their own serviceman, the person I talked to made me feel like a complete idiot. He said in his twenty something years of selling Maytags, he had never heard of such a thing. Anyway, when a serviceman finally came, he also had to replace another part due to a recall. Now, my washer is right at four years old and is leaking from under it. My husband checked the hoses, and they are not the problem. I bought a Maytag thinking I was buying the top of the line but I guess I was wrong. I will not buy another one nor recommend them.

I just bought this piece of junk... Like everyone else I guess I didnt do enough research! I have had this washer for less than 3 weeks and just like everyone else I am so disappointed in how it tries to wash without water! I too have tried different settings. I had to wash a load 3 times... pausing it while trying to get the rest of the items wet. Its ridiculous... of course now to try and see if I can return it! Yah right... Home Depot does not have a good return policy and Im afraid I will be out 800+ with this washer. This is ridiculous! It really is.

It’s a nice look to your kitchen first, and an easy clean. Works great for heating up stuff in a hurry and makes popcorn perfect on the popcorn button. Does ok at melting things. I have been happy with mine for 3 yrs so far.

The control panel of my dishwasher is malfunctioning. I looked this up online and ran into a recall for the heating element. Sure enough, my dishwasher is effected. I asked why I was not contacted. First they made up a story as to not having my contact information. This is simply not true, as I purchased the dishwasher directly from Maytag. Three years ago there was another recall and the heating element caused another problem so Maytag replaced my dishwasher.If a heating element overheats, it seems to me that a short-term affect could be overheating the control panel, causing it to malfunction. I read through a few recent complains and would also like to inquire about having this issue looked into by the Consumer Affairs.

6 week old High Efficiency Washer leaves lint and soap lines. Ive tried deep water wash plus the 2 rinse settings and I still have to wash the load twice to get rid of the lint lines and soap lines. Ive also tried every combination of settings to no avail and I follow the guide to a tee because this machine actually weighs the clothes to determine the water level. Maytag customer service was polite but useless. Im assuming its the poor design but customer service says I will be charge for the warranty service call if no problem is found. Maytag, another fine company down the drain. PS, parts are made in China.

When purchasing a microwave for our kitchen the Maytag MMV4203DB00 had all the functions I wanted. Just after a year its quite cooking. The fan would still run but not heat anything. I called Maytag and was told basically, tough luck. I said something about Maytag, that it was supposed to be a great brand and should last longer than 1 year. The part to fix it plus labor was going to cost nearly as much as a new microwave to replace it. Now, the microwave has started to turn on by itself. Customer service was very rude and came off with a we dont really care attitude. I will never buy Maytag again.

Hi we bought Maytag washer & dryer from Lowes last year. Since then it burned every single fabric silk to cotton, tops, pants and sheets to comforters even on delicate setting, costed me thousands of dollars. We are totally wasted our time and money by buying this product. I would never recommend to anyone. It’s disappointing and pathetic to see how they even pass the quality testing before they release to the consumers. All my brand new clothes and comforters one wash and they are ???? burned. Not even one star worth my time. I cant wait to get it replaced ASAP. I have pics to provide. Totally dissatisfied with this dryer. Washing machine is two star only compared to other brands.

I have only had this machine for 2 weeks after having a Maytag since 1994. Even broken, my old machine was far superior to this one, a Maytag Bravos. Fortunately, the salesman noted that I wouldnt be happy with this machine but, thanks to a government mandate, all new machines behave in a similar manner to save water and energy. This agitator-less machine neither washes nor rinses the clothes/bedding/towels properly. It takes four times as long to wash the items but doesnt get them nearly as clean. Today, I put 2 pairs of shorts, 2 T-shirts and a standard bed-sized mattress cover in to wash. The mattress cover never even got thoroughly wet even though I used the deep wash and extra rinse settings. Last week I put sheets in the sheet setting only to have them come out totally wrinkled and stiff as a board with soap even though I used the recommended amount of detergent. This is a disaster. Shame on Whirlpool/Maytag and the U.S. Govt. A river and a flat rock would work better!

After owning my refrigerator for about six months, it started to reek, the smell permeating all of the food in the fridge. After cleaning and disinfecting the fridge and throwing out all of the food I found that the smell was just as bad as before. When I checked online I found that Maytag owners have been complaining about the smell for over a decade now. It is caused by a poorly installed drain pan. The fridges design directs air flow so that the smell enters the fridge and distributes it evenly throughout the fridge.

3 months after we purchased our Maytag dishwasher in Jan 2014 (Sears) it broke. The service person told us that the ELECTRONIC CONTROL PANEL (START, CANCEL, WASH CYCLE SELECTIONS) was a common breakage issue and fixed it. It broke again around one year from our purchase date. Same issue, but kept working and not working. Finally we contacted Maytags customer service. Although courteous the only thing we were offered for this common Maytag issue was a $249.95 one year warranty for them to come and fix this recurring problem. I explained that we had already spent about $870 (including tax, delivery and installation) for our middle of the line dishwasher one and a half years ago and asked if they would consider either charging us for a smaller service call/repair or just do it because it seems to be a design and manufacturing issue. After one hour and no sympathy I had to pay the $249.95 to get a repair person out and be covered for one year from today. I dont trust the cheap quality and the lack of support for the product. THEY ARE OUT THERE TO SELL MORE INSURANCE AND CUSTOMER SERVICE DOESNT MATTER!

The only time one can get enough water into the washer to actually get ALL the items wet (or even damp) is to put it on BULKY sheets or HAND wash settings. That is true for any size load whether it be 1 item or 10 items. I prefer being able to get ALL the water I need first, then put in the clothes, then soap, but thats not allowed. First soap, then items, then a bit of water only after you close the lid. They like to say that the spinout dries them which is why they arent damp - but that is a lie when you can smell and see the dirt. I want my OLD STYLE back!

My Maytag is 2 weeks old, and knew from the start I had a lemon. The compressor sounds like a giant freezer. I had the service man take a look at it, and while he was here the compressor did not come on. He pulled the plug from the fridge and turned it back on and still it did not turn on. I asked him to stay till it turned on and he said he could not stay any longer. I waited for him from 2 PM till 7:30 PM. He was to arrive between 3 and 6. Talk about frustration, and I only wish I had read all the reports before I bought this junker. I was so worried I decided to get the insurance for 4 years. The reason the ice forms is because you have no control over the ice. You cant see them and they get stuck. I had a side by side before this, and I can kick myself for not buying a side by side again. I was told to shut it it down when youve had enough ice cubes, to stop it from getting stuck. This ice maker is so big and so hard to pull out and the switch to turn it off is on the inside. So far my only complaint was the humming, but I can see a tough road ahead.

The Maytag Bravo is a big waste of money. Get a less expensive machine. You will have no problems and save money. This is my experience: SETTINGSYou cannot control the settings completely. Every setting is preset. For example, if you choose the Bulky setting, you cannot choose the water save spray rinse. Those two cannot be selected together. Certain settings can only be selected with certain temperatures. This will however be the least of your problems. WASHINGIt does not get clothes clean. I have had instances of items coming out with still stuff stuck to them, not just stains, but actual solid material stuck to it. My cat threw up in his bed and when I got it out, it still had small pieces of vomit stuck to it. I have always only used the Bulky setting which fills up the whole drum, so there is sufficient water to wash. I cannot imagine what it would be like if I used the Normal setting. Many times I had to wash thing twice. If you use the normal setting, you will get hardly any water. It will be a moist bundle of clothes moving like a big lump. You need water and some degree of friction to eliminate the dirt. SPINNINGIt is constantly stopping, beeping and showing me the UL sign (uneven load). You have to unravel the items and reposition them Around the drum. If you are an old lady like me, this is a real chore because the items are now soaking wet and very heavy. Also, because there is no agitator, the items come out in knots (tied to one another) and you have to separate them. DURABILITYThe lid is loose. It looks like it may be missing a screw on one side. It still locks, but it moves sideways when you close it and open it. BOTTOM LINEThe whole thing is a disaster. Get an old fashion type. It will work better and you can save your money. I honestly think there should be a class action suit against Maytag.

I purchased this Maytag washer/dryer set in February 2017 and I am very, very happy with it. This is a brand that has proven dependable for more than 80+ years. This is a low water washer that saves money on energy bills. I love the extra large capacity and was very concerned how well it would clean without an agitator. But having confidence in the name, which is why I purchased this set, I was very pleased with the cleaning power. The only disadvantage I see is with the soak cycle which is timed. I would like to have an option to soak indefinitely. So if you are trying to remove blood stains, you may have to use the soak cycle a few times before all the blood is removed. (Assuming that you are only using cold water and no additives.)

We (family of 2) purchased our Maytag Bravo XL Washing Machine Model#MVWB880BW in Nov. 2013 for over $700.00. Last week, Dec. 2019, the washer would not finish the rinse/spin cycle. The clothes were still wet. I researched troubleshooting in the Maytag booklet included with the machine and tried everything. It still showed an OL on the readout. It was not overloaded as I only had 3 towels, 3 washcloths, and 3 hand towels in the washer. I tried just the rinse/spin cycle alone to get the water out of the clothes, but they remained wet, and the OH still appeared on the machine. When I called the place where we bought it, they suggested unplugging it, waiting and plugging it back into the outlet to possibly reset the machine. That seemed to work for 1 very small washload. The next day, I tried washing again and the OH appeared with the clothes still being wet. We had a repair person come out. The service call/diagnostic of $116.98 plus repairs of $304.41 plus $95.00 to install of the new Motor Control Board. I feel that cost is excessive for only 6 years of service. Before we bought this machine in 2013, I had a Maytag which lasted over 20 years with NO problems. I always thought Maytag was the best washer, but this experience has proven to change my mind. We went out and bought another washer rather than replacing the board not knowing how long the new one would last. Needless to say, we did not buy another Maytag. I do not feel I can trust the Maytag products anymore. After this experience, I did more research on the Direct Drive used in this particular model washing machine and found that it had been problematic. I would have thought Maytag would have offered a recall to avoid these costs/problems and avoid dissatisfied customers. Along with the original purchase of the Maytag washer in 2013, we did buy the matching dryer and are hoping the dryer will last longer than the washer. We shall see.... This has been an unexpected and expensive lesson.

Maytag may have pay to replace defective controls. 1-866-931-7384 is the number to call. I have owned my maytag dishwasher for about 18 months. Its control panel was never great, but now my dishwasher wont work at all. Apparently, the tiny inside the control panel rust away because they arent sealed.

I purchase my first glass top stove; a Maytag. It came with a 10 year warranty on all elements and the glass top. As this is a first glass top I read through all instructions, there appeared no real warnings on what to do to maintain the glass; or rather what would damage or void a warranty. I simmered some maple syrup, and as it so often does when reaching the proper temperature, it boiled over. On a regular burner, one just uses a little elbow grease and your stove is returned its previous state. This actually pitted the glass, and as the warranty people at Maytag informed me voided the warranty, and seriously weakened the glass top suggesting it would be likely to break. Seriously?????? All of us boil stuff over on the stove top from time to time, and this damages the glass top and voids a warranty??? VERY DISAPPOINTED in Maytags product and their warranty.

I bought a Maytag refrigerator over the summer - the French door and drawer freezer. Expensive but crappy. After about a month motor starting making noise then is shut down. Called the store. They came and swapped it out and not even two weeks later same thing. Looked up product and all awful reviews. Never thought to look up reviews before purchasing. Could of save myself the headache. Not to mention my daughter was like, Mom stop buying that brand. It sucks. Did you not realize our washing machine is the same brand and after almost two years it started acting up and your last washing machine you had for 10 years before it even gave you any problems.

I have always loved Maytag but this top load washer is a bust. I purchased this higher dollar energy efficient washing machine to hopefully get the value out of it for years to come. Model MVWC565F. 4.2 Cu Ft. I use good quality liquid laundry detergent. I launder adult clothing (including business casual wear), sheets, towels and pet blankets. Occasionally the 20+ something children do their laundry while home. I often have dry spots on my clothes where they never got actually wet. I switched to only using the deep water cycle; however, this does not immerse the load in water. The smaller my load the less likely to get clean. Ive adapted to only have large loads but I still do not feel my clothes are getting clean. I often have to run the load a second time to not only remove ordinary day-of-wearing smells (very noticeable in socks for example) but to get them all wet and free of soapy/linty-like spots left on the clothes from the washer (most notable on black leggings, dress pants, etc). I always do my towels and bedding separate from daily clothing, so this is not coming from having a mixed load. I have also noticed that the load takes much longer (up to 2 hours) for my washing cycle. How is this energy efficient? It uses less water but more electricity? I miss my old fully-immerse-in-water washing machine that washed in under an hour! Love the dry that I bought with this but not the washing machine!! I do not recommend this washing machine!!

Do not buy a Maytag dishwasher with model # MDBH969AWB1. I bought this dishwasher last Dec. 2010. I could not use it for 2 weeks, because the door would not shut. The repair man came & fixed the door. Then when I actually got to use it and after it finished running the cycle, the tub was dripping with water all over--top, sides, door, bottom. I had to dry the dishes on the top rack, and I had to leave the door open for days in order for the inside to eventually get dry. The first thing I noticed about this dishwasher when it was installed was that it was smaller than my other dishwasher. I hate the design because of the way they have made the racks plus because it is smaller--it holds less dishes than my old one did. I could actually get almost twice as many dishes in my old one than I can with this one. Do they not think of asking the consumer about what they want in a dishwasher instead of going ahead and making something that is not functional?I am so frustrated with this thing; it has brought me to tears. I just today went to Sears and looked at their Kenmore dishwasher. It is designed more like my old one than any of the other makes out today. I wish I had checked this out, before I bought this Maytag. Weve always heard how Maytag is at the top of the line with no problems, right? Dont believe it. I will never buy another one. Whoever is designing these dishwashers need to go back to 1990 and take a look at how it was designed and then go back to making them like that. I loved my older dishwasher, and I wish I had never let them take it away. I wish I had taken the money I spent on this ridiculous Maytag and had my old one fixed no matter what the cost. I made a terrible mistake.If you have an older dishwasher and it has given you good service for years, I suggest you have it fixed and keep it, because you will not like the performance of what they are selling today. It does not matter what brand you buy, they are all designed the same. Just take a look and compare them. But if you buy, please check out the Kenmore. I dont know if the performance is better, but the racks are better designed. My old dishwasher was a Hotpoint. It was the cheapest one on the market, and it gave me the most wonderful service ever. The dishes were always very clean, the heating element was fantastic, and it always dried the dishes completely. I cant believe they would make a product like they do today and sell them for what they do. The heating element in them today is not as good or strong as what they used to make. That is why the dishes wont dry properly. You get way less than what you pay for. Thinking a new dishwasher is the way to go, think again. Please, if at all possible, keep your old one and have it fixed over & over again. I hate this dishwasher. What a joke on the unsuspecting buyer.

Maytag used to make a great laundry machine. The barrel of the Bravos XL machine is very deep, and it is difficult to reach the bottom of the machine to get clothes out. My biggest complaint is that the clothes dont get clean; there is not enough water filling the machine to clean the clothes. The clothes get wet, but there is no agitator, and the water isnt deep enough to suspend the dirt and wash it away, even on the deep wash setting. There is also a lot of lint left on the clothes that cant rinse off. Why is the barrel of the machine so deep if it only fills up 1/6 of the height? I had great hopes, but I really regret buying it.

I would not buy a Maytag again. I am very disappointed with the noise level this dishwasher produces. I am also not happy with the inside capacity. I never have enough room for all the dishes when I have dinner parties.

We purchased a Maytag front load washer and matching dryer in 2007. In 2010, the main control board of the washer broke down. We spent $450 to replace it.In 2014, the washer stopped working. The dryer started producing horrid odor when we used it. We replaced both with LG recently. We NEVER buy or recommend Maytag products. Stay away from Maytag. There are many other reliable washers and dryers in the market. This is to help other consumers.

Im so mad over my new purchase on the XL Bravo washer and dryer and Home Depot will not return. I have 3 kids and a hard working husband. My clothes do not come out clean no matter what cycle I use. It takes forever just to wash one load. If you spill something on your clothes and it dries crusty it will come out of the washer crusty. I want to cry. So much money wasted and cant get our money back. Would never recommend a washer without an agitator. Towels come out soaking wet, and dont spin dry if heavy...forget washing a blanket. 4th day using the dryer and now there is no heat. What was I thinking!! So mad and sad too!

We purchased a Maytag refrigerator model # MSF25D2EAS on 10-22-2012 at the Home Depot in Tracy, CA. On 2-2-2014 (15 months) we noticed a puddle on the kitchen floor. Upon inspection, we noticed that the refrigerator was not working. Went over to Home Depot and were given the name and number of the authorized Maytag repair dealer (A and E). The technician arrived on 2-5-2014 and replaced the compressor on-off /overload relay and charged $243.82. On 2-16-2014 (11 days later), the same thing happened again. The technician came on 2-19-2014. This time, it was the compressor at a cost of $800.00 plus the $75.00 service call. One can purchase the compressor online for $300.00 and I am sure that A and E buys it for a lot less. We thought about it and decided not to get it fixed because we did not know what else would go wrong and how long would the second compressor last. We talked to the Appliance Departments assistant manager and were told that Home Depot does not give any kind of consideration and she had worked there for 11 years and had not heard of any problems. She was not telling the truth or she was not aware of the numerous negative customer reviews online. She also informed me that I should have bought a warranty. We have bought quite a few refrigerators in 50 years and they lasted for many years. Home Depot sells inferior products. Maytag must sell these inferior products at discounted prices and of course, some stores are looking for larger profits. I do not trust Home Depot any longer and will not purchase appliances there anymore. It was a very expensive lesson - the price of the refrigerator, loss of food (twice) and the stress it caused. We bought a new refrigerator at Sears and it was not a MAYTAG.