Purchased this double oven back in 2012 and have had to have the control valves replaced twice because of them jamming and snapping. The burners are undersized for cooking and it takes forever to get water to a rolling boil. The broiler in the upper oven needs constant attention when using it because food cooks unevenly and burns quickly. The lower oven is great, convection is awesome. I have seen the Maytag repairman more from my stove than I have for any of the other appliances I owe combined. Maytag should stick to appliances that only use water.

We were very impressed with this dishwasher when we bought it about 2 years ago. It looked very nice, it was the quietest running dishwasher weve seen, dishes came out sparkling. However, the nightmare quickly began. It started with having to cancel then resume. It ran for 8 hours non-stop (still cycling the next morning). We unplugged it and we were able to use it normally for a few times. Weve had so much aggravation with this machine weve decided to (A) Never to buy another digital dishwasher, (B) Join the class action suit proposed against Maytag. We have tried all the reset solutions offered and Weve been hand washing dishes (again) for days.

I have had this dishwasher for 3 1/2 years. Replaced the touchpad 2 years ago and now the touchpad is dead. I read all the other comments that are similar to mine and am thinking to replace this junk dishwasher. I will not be buying from Home Depot as they are selling cheap products that are defective!

I always thought Maytag was the best, maybe because of their ad. Finally, I bought a refrigerator two months ago, which has turned into a nightmare. The company has sent a tech six times and they all say that it is a bad design which makes my vegetable drawer full of water because of moisture. And they refused to do anything about it every time (bad management). They have already spent more money on service than what I paid for the refrigerator. Figure that out.Do not buy Maytag. It was the biggest mistake I made. I also bought a washer and a dryer at the same time. I wish I could send them all back because of the ignorant people they have working for them in their complaint and service office. Anybody out there, if you want to buy an appliance, make sure it is not Maytag.

I purchased a Maytag dishwasher for $500. After several months of it working less days than not working, I contacted the repairman. I paid $350 to replace the control panel. I wish I had just replaced it with a reliable product. 1 year into ownership and the seals on the door are falling off. May I suggest never purchasing a Maytag product?

Very Poor Quality from Maytag Although (Dishwasher, model MDB8959AWS) - I knew Maytag always had a reputation of selling quality products I have never purchased a Maytag appliance because they usually cost more than other brands, so this is my 1st Maytag product. After ~25 months (after all warranties have expired), the unit stops working. The lights seem to have a mind of their own. I removed power from the unit for 1/2 hour attempting to re-boot the computer but the condition did not change. After researching the issue online, I found that Maytag has a two big problems: 1) Defective dishwashers, 2) Bad or no customer service.I am an engineer and this type of a problem (it happens from time to time) MUST be acknowledged and the customer made whole or the reputation of the company is destroyed and future sales will (and should) diminish to the point that the company may(?) go away for ever. I know products are not designed to last a lifetime like they were in the 60s & 70s but 3.3 years for a $650.00 appliance is way out of line. The dishwasher we replaced was ~18 years old, and we only replaced it because my wife wanted a more modern look.

My husband and I purchase both Maytag Washer and Dryer 7 month ago 2017, because we have purchase Maytag washer before and were very happy with it. But this new Washer does not clean clothes at all, it is worthless. We will not purchase another Maytag Washer again.

It meets all of my needs and expectations. Its quiet looks nice and does a very good job of cleaning dishes.

Lid lock issue. 2 years old. I will never buy a Maytag, or any other Whirlpool brand for that matter. I am VERY disappointed. A service call will cost at least $200 dollars so why not just buy a new washer for that price. Also, I read that consumers should stay away from automatic water level washers. They never work right.

I have had this range (Maytag MER8775AS electric range) for 36 days. The hot surface indicator light doesnt come on (bulb is fine) and the heat elements turn on and off on their own when I am cooking. 36 days! This thing is junk! I am going to see if I can return it, even though it is outside the 30-day window.

Recently purchased Maytag Washer and Dryer from our local Home Depot June 2020. The appliances were finally delivered in August. When both appliances were installed, the installers made sure the washer was working properly and there were no leaks. They did the same for the dryer to make sure it was working properly. When the dryer was turned on however, the motor blew up and there was smoke coming from the dryer! I am now sorry I purchased Maytag. I had narrowed my choice between purchasing Samsung or Maytag. Im now thinking I should have gone with Samsung. Im supposed to receive another dryer today. The washer works, however its very, very loud. For the amount of money I paid, I hope these last for a while.

Our Maytag dishwasher was just past the 1-year mark when the control panel stopped working. A certified Maytag repair service came out to diagnose just that and charged us $89. Maytag sent the user interface out to us, and my husband noted that there was absolutely no way that the part could be installed wrong. The wires could only go one way. The repair service (DSM Appliance Service) wanted another $120 to install it. We installed it, and it still doesnt work. Maytag will no longer assist us in any way. I will never buy a Maytag or Whirlpool appliance again. After investigating, I see that this control panel issue has happened many, many times; and I wonder why there hasnt been something done about it.

I purchased a Maytag Dishwasher in March 2013 and the control panel failed in July 2014. I, along with hundreds or thousands of others it seems, discovered that this is an extremely common issue with several models of Maytag dishwashers. Rather than standing behind their products and making it right for their customers, Maytag is hiding behind their one year warranty and refusing to do anything about it or even admit they installed thousands of FAULTY control panels. This has been an expensive, infuriating issue to deal with and I have never been so dissatisfied with a company. Bottom line, they made a bad product that should have been recalled. It blows my mind that they are getting away with this. I wish I had known the recent changes in Maytag/Whirlpool and I wish I had done my research prior to the purchase.

I purchased a floor model Maytag Dishwasher from Abt electronics about a year and a half ago. 2 months ago, various light started flashing. Somehow I managed to get it going. Some blogs reported it might be a drainage problem. Others suggested pressing a certain sequence of buttons. After Each time I got it to work, it became harder the next. I bought Maytag because my old dishwasher lasted 13 years. What is interesting is that a company whose name Ive forgotten sent me bimonthly requests to purchase a warranty from them. Now they have stopped. I am a single mom of 3 with an unemployed ex. I work and support my family without any assistance. I count every penny. I cannot afford repairs nor a replacement now or any time soon. This is a travesty.My door says 10-year limited warranty and the delineates stainless steel tub and racks and chopper blade, but not the panel. I do not understand how Maytags denial of the problem and their unwillingness to correct the problem can improve their image. I will never purchase from Maytag or its associated companies ever again. What a scam! To be honest though, I have not contacted the company since it is not under warranty and all the blogs have relayed the same message: Maytag denies there is a problem.

This product has cost us thousands of dollars in clothing!!!!!! We have a lot of pictures to prove this!!!! Greg Mackie Major Appliance does NOT back this product or US the consumer!!! We have bought THREE households of products from this distributor & they have NOT backed any of the products that they have sold us, or given us Any discount for repeat business or loyalty and have NOT Supported us in any way whatsoever!!!! We have spent thousands of dollars and have had NO compassion or support whatsoever!!!!!! We expect a full refund for this Failure of YOUR product & a NEW Machine that will CLEAN our clothing & NOT DESTROY it!!!!!! Very Disappointed in this Product!!!!!! We Will NOT purchase another product from Your Company or from this Distributor unless YOU make a conscience decision to make this situation Right!!!!! We Will Spread the Word about your Failure of a product & detour business from YOU & YOUR Distributor!!!!!! We have numerous other photos to share with consumers of how YOUR product has destroyed our clothing!!!!!

I purchased both a Maytag washer and dryer and I am very disappointed in both products. Both appliances have electronic controls and are substandard. For the dryer if you do not touch the start area exactly right it will not start, can take multiple tries. For the washer, my town turned off my water to switch out the meter, once done the washer did not know how to clear the air in the lines and gave a LF error and no one at Maytag customer service could help me solve the issue and then could not set up a service call as their computers were down and did not have a process to call back the customer. This is terrible Customer Service - never again Maytag or any of their other products????

I purchased a Maytag slide in range from Costco online in April 2020. Within three months a discolouration on the stainless top part of the range has happened. Costco has a ninety day period for repairs, or return on appliances. Pictures were provided to Costco at the request of Maytag. Upon review, Maytag’s response was, This is a cosmetic issue and nothing we will repair. I am an extremely disappointed consumer who will NEVER purchase a Maytag product again.

Bought this (Maytag Washer MVWB955FC1) on 1/8/18, was delivered late in January as it was on back-order. On 4/30/18, during a cycle, the washer made a pop sound. There was glass everywhere. The glass had shattered and exploded onto the floor and washer. The glass is on the inside of the drum and all over the clothes. Contacted Maytag and they sent out a repairman the next day. Repair said there is a point of impact indicated I dropped something on it. NOTHING was dropped on it. There is a point of impact, from the inside. The glass is pushed up and out indicating pressure from INSIDE the washer.Repairman says its not covered under warranty and that I had to pay for his time as well. He also said there are no known issues with this lid and washer. The lid is out of stock and wont be available for a while. I called Maytag and they gave me the same response, never heard of this.. and lid is out of stock. I found SEVERAL reviews/complaints in which, for the exact same model, this has happened to other people. This glass lid is dangerous and poses a serious safety risk to households that contain it. If they replace the lid, there is no guarantee this will not happen again. A child could walk by the washer and at any moment the glass lid could explode, send tiny shards of glass everywhere. I want a refund for this dangerous washer.

I bought the power wash Bravos XL... Bad. It does not rinse the clothes, leaves residue on dark clothes.. probably all clothes - cant tell on lighter colors. I dont recommend!!! Waste of money.

I purchased a Maytag dishwasher in 2013 and the control panel needed replaced within the warranty period. About a year later, the control panel started to malfunction again, this time out of warranty and Im told it will cost over $350 to repair. I paid a lot for this dishwasher and thought I would get years of use out of it. I plan on buying a new cheaper one (not Maytag) for a little more that the cost to repair the Maytag. Im very disappointed and will not purchase another Maytag. I also read online that Im not the only one experiencing this problem.

Spent a lot of money on a Samsung washer. Will never buy that brand again. Too much money for only working for 2 years. And left clothes dirty. Had to wash clothes twice. My Maytag washer was bought with a deep water wash cycle. Totally love it. Also not a front loader.

We have had washer/dryer Bravo Series and been nothing but horror stories. Washer bounces all over room to point hoses come out and flooded my laundry room and foyer and garage. It takes over 1hour 45 minutes to do loads sheets which is 2 sheets 2 pillowcases. The repair man told me that takes that long due to MY sheets are dirty. I have been married 46 years and never heard that ever!!! The dryer is just as bad, takes over hour and half to dry sheets and towels almost 2 hours to dry. DO NOT BUY MAYTAG ANYTHING. The person who said needed hurricane straps to hold washer is something I agree with. Just a horror.

The Maytag MFI2568AES refrigerators ice maker is broken and we cannot get a replacement unit. Whirlpool who now owns Maytag is of no assistance. The unit is two years old. I understand planned obsolescence but this is ridiculous.

We have a Maytag Neptune washer and dryer. The seal is full of mold. We replaced the seal a few years ago and I wipe it and try to clean it every load, but it is useless. I saw there was a class action suit and I was never notified of this. I would have participated. I want it fixed, replacing the seal does not work.

Ive used Maytag Dishwashers since the 1980s, from Alabama to California. And I wouldnt change a thing. In fact my entire family (well the folks that can afford it) uses maytag dishwashers. Extremely satisfied we are.

We bought this Maytag Bravos top loading washer 2 years ago after having bad luck with a front loading Maytag. Maytag was always the top brand to buy so I thought it was the style washer but now I believe Maytag has failed to keep their standard of quality high. My clothes come out of the washer almost dry and full of lint. Even though I use the HE wash soap, it does rinse out of the clothes. Dark clothes come out with a noticeable scum so I suppose the lighter clothes do, as well, I just cant see it. I sometimes have to wet the clothes down to get them clean and I always have to double rinse them which defeats the whole economy issue. Im not happy with this washer and would not recommend anyone to buy a Maytag brand washer.

We purchased a TOP of the line Maytag dishwasher with the expectation that we were also purchasing high quality. Boy, were we wrong. Continuous problems with the controls since out of warranty. The controls are in the door and operate pushbutton from top. This is electronic pushbutton not actual pushbuttons.MDB89595SBS.

I am extremely unhappy. This is a terrible washer (Maytag washer MVWC565FW). I am so sorry I didnt buy a GE. Terrible loud noises, shakes and vibrates like a plane taking off. Funny smells as if something is burning. Repairman came 1 week after purchased and stated nothing was wrong. A huge waste of money, I HATE, HATE this horrible machine!!! Totally unsatisfied, I would never purchase anything with the Maytag name again!! Wish I could get my money back!

I purchased a Maytag Dishwasher (MDB7749) in 2012 and one day before my 1 year warranty was up, my start button on the control panel wouldnt work. I called P.C. Richard and they sent a repairman who fixed it. This was in June of 2013. Here I am now hand washing again 1 year and 4 months after the repair. I called P.C. Richard again and was told that all brands have their weak points and because I got it on sale in the first place, I should not feel angry.Now that I am reading the reviews from 5 years ago, I realize that P.C. Richard knew this was an issue and chose not to disclose it or stop selling it. I had my G.E. for 10+ years and will go back to one. As I have no money for another new one, I will try to learn to fix this one on You Tube.

Our range and oven are reliable and durable. Easy to clean and have lasted a long time. I do not regret spending a little extra money to have an appliance that has lasted a long time. The oven heats up at a standard rate. The self clean function is very thorough. I have a white set. I was worried they would stain with your typical spills that come along with cooking. However, They clean very easily.

I have always loved Maytag but this top load washer is a bust. I purchased this higher dollar energy efficient washing machine to hopefully get the value out of it for years to come. Model MVWC565F. 4.2 Cu Ft. I use good quality liquid laundry detergent. I launder adult clothing (including business casual wear), sheets, towels and pet blankets. Occasionally the 20+ something children do their laundry while home. I often have dry spots on my clothes where they never got actually wet. I switched to only using the deep water cycle; however, this does not immerse the load in water. The smaller my load the less likely to get clean. Ive adapted to only have large loads but I still do not feel my clothes are getting clean. I often have to run the load a second time to not only remove ordinary day-of-wearing smells (very noticeable in socks for example) but to get them all wet and free of soapy/linty-like spots left on the clothes from the washer (most notable on black leggings, dress pants, etc). I always do my towels and bedding separate from daily clothing, so this is not coming from having a mixed load. I have also noticed that the load takes much longer (up to 2 hours) for my washing cycle. How is this energy efficient? It uses less water but more electricity? I miss my old fully-immerse-in-water washing machine that washed in under an hour! Love the dry that I bought with this but not the washing machine!! I do not recommend this washing machine!!

When we turn up the temp in the oven above 400 degrees, noxious fumes come out giving us headaches and nausea. We have to open all the doors and windows and bring extra fans...very toxic. PLUS the vent for the oven is at the top of the oven door, so the knobs for the burners get so hot you cant touch them!

I purchased a MTW6600TB0 Washer and Dryer on 6/17/07. I have had issues with the washer from the beginning; smell in towels and mechanical problems as well. The machine does not fill properly and receive error codes that are electrical issues per A & E service. I get LF errors occasionally and randomly on different cycles. I finally called for service because I now am receiving F51 Error, which has to do with the basket per A & E service technician. I was told on Black Friday that my machine required both baskets and the rotary motor. My machine is just 4/5 years old. No unusual wear and tear. There are only three people in my family and we live in a fairly warm climate so no heavy winter clothing, etc. I was told that my stainless steel basket was rusting to my plastic basket. I am still trying to comprehend the fact that two materials that are not supposed to rust are rusting. After looking for a new washer over Thanksgiving weekend, I find out that Maytag warranties their stainless steel basket and rotary motors for 10 years. So do they warranty the things they say the warranty or not? Of course, it is a holiday weekend and I cannot get a hold of Maytag. I paid for a service call and the technician told me I would be responsible for the repairs at about $500 for parts plus labor. I looked up the parts he recommended replacing and it was over $800. I paid $1000 for this machine less than 5 years ago. Thats $200 a year for the privilege to use a Maytag. Additionally, my set is black. I can not find a black washer anywhere.

We purchased kitchen appliances in 2012. A Maytag French door fridge, dishwasher and double oven range. So far my lights on the range have not functioned right as to which eye is on on the smooth top range, the ice maker burned out and now the control panel on the dishwasher has burned out. All of course are out of warranty. We have replaced the ice maker. Now in search of the control panel for the dishwasher. Havent priced the part for the range yet. I do know that I have a Maytag washer and dryer that so far are between 10-15 yrs old and knock on wood they work great. But I will NEVER buy appliances with the name Maytag on them again. So sad that you spend top$$$ for 1-2 yrs of the appliances working correctly.

I have a Bravos washer model # mvwb45owqo and matching dryer. The price for the pair was $1347.00 plus tax. The washer and dryer were bought Jan 14 2010. 10-10-13 the pump went bad and was replaced. I paid $ 221.00 to have it replaced. 10-31-2013 I was washing a load of cloths and it was very noisy. I call the local dealer and they come out and said that it needs a drive shaft tub part #w10193886. I would be about $300.00 to replace the part. Also they charge $75.00 for a service call. I called Maytag and talked to Ashley (**) from customer service and she said they could not give me any help that the washer was too old. I might also add that my last washer was 3 years old and the motor needed to be replaced. It was also a Maytag. I always thought if you paid more money for quality it was worth it. I am sorry I did not buy a cheap machine from Sears or somewhere else. It would of been 1/2 of the cost and I could of replaced it after 3 years or so if necessary and still been money ahead. We also have 4 rental homes that have all Maytag in it. I will be holding my breath that they are not junk also. I will tell everyone I know not to buy Maytag and I will never own anything that has the Maytag name on it again.

My washer is new, out of warranty, and about 2 and a half years old. All of a sudden, with no warning or previous issues, the computer board in the washing machine malfunctioned which caused a humming noise, it would not cycle into the next wash phase, the time would go up instead of down, I could not change cycles, and when I would push the power button there would be a delay of power coming on. I unplugged and called my local appliance repair and he said he sees problems with this model regularly, although not always the same issues.Before purchasing I scoured the internet for reviews on different units to make sure I didnt get a lemon. I think Maytag saw the error of their ways quickly and stopped making these before people caught on. This model is no longer being made. I like matching units, so it meant either shell out $500 for replacing the board, or replacing both the washer and the dryer that still works, which would be about $1200 or more for a new set. I chose the least expensive route for now. Not that it matters where I bought mine, but Home Depot and it was on clearance so it was a good price. I have now made up for that difference in repairs.

I purchased a top load Maytag washer the spring of 2019. My clothes come out partially dry, with a film/residue, and debris left on them. I was told that they use considerably less water; however there is not sufficient water to wash away small amounts of anything left on clothes. I have contacted Maytag 3 different times. Each time my concerns have been dismissed. The only solid advice they gave me was to use less soap, which hasnt changed anything. They also told me to clean my clothes before I put them in the washer (we have no children at home; Im not talking about really dirty loads). They told me there was nothing they could do, and I was just stuck with the washer. I am completely dissatisfied with this product and the Maytag service. I would not recommend their washer or their service. The dryer works just fine.

Im have finally given up and purchased a replacement for my Maytag Bravos XL Top Loading High Efficiency Washer! The Maytag was 2 years old and I have ALWAYS had trouble with it. My towels became sour after 1 or 2 uses (sometimes they smell sour even before use!). My dark clothes ALWAYS came out of the wash LOADED with lint. I researched online to determine whether these were common problems and found several sites with suggestions such as: dont use more than 1-2 spoons full of high efficiency detergent (which recommendation I followed), Use white vinegar or liquid fabric softener. (I tried both with only minimal results.) ALSO use a dryer sheet in the dryer (I did this but it seemed like a waste since I was already using fabric softener in the washer). Dont overload the washer. (I didnt, but if I couldnt fill it, then why did I buy a washer with such a large tub ?!) Clean the washer monthly. (I faithfully did so, and tried alternating Affresh and bleach to see if theres any difference in the result... not really. Make sure you are fully drying the towels (I ALWAYS DID!).We had a Sears repair technician come to the house the last time my frustration level was overflowing and she only made me feel like an idiot, repeating some of the above recommendations and insisting they would solve the problem -- which, if they had worked, would have precluded my need to call a repair technician!!! The repair technician provided no other service or ideas to fix the problems. My husband decided we should go back to the tried and true agitator-type washer... bye-bye, Maytag Bravos.

The refrigerator has been very dependable for over 14 years. The biggest problem we have had is failure of plastic tracks on drawers that break and had to replace drawers and other problems with plastic components like deli drawer coverlet, and door shelf door plastic. Recently we have problems with the touch control panel on front of door. Not working properly for ice dispensing and temp. control although temp is maintaining what we had set prior to failure of control panel.

Weve had this washer for five months now and really regret buying it. It cannot remove even minor stains and often leaves residue on clothes, even with extra rinsing. I spilled coffee on some fleece pajamas and it took four washings to get the smell out.

Dishwasher is around two-three years old and it will not start or drain. From what I can tell on the internet, this touch-pad control panel has been an ongoing problem for Maytag. Will try to fix myself, and if I cant fix it, I will buy a new dishwasher but not a Maytag. By the way, my washer and dryer both went out this year - five years old and both are Maytags. Stay away from this brand.

We purchased a Maytag Dryer with the lint vent on top on March 21, 2014 from ABC Warehouse in Ann Arbor, MI. Whoever engineered this does not dry clothes. Trust me, this will be the last Maytag I buy. There is lint seeping out of the top and when you clean it the lint gets all over the place therefore, my laundry room is always full of dust.

I bought a Maytag Bravo without an agitator. Regretted from the 1st load. Some of my clothes do not even get wet and I bought the commercial grade. My 20 year washer that was on its last leg washes better than my brand new Maytag. Please do not waste your money, your clothes will not come out clean.

Our control panel just went out...purchased in November 2015. From reading reviews it appears our only option is to purchase a new control panel and hope for another two years. Ours (MDB7749SBM3 Dishwasher) was purchased from Sears and was not cheap. When is Maytag going to recall this panel? I read reviews that this problem goes back to 2011.

It’s a front loader, very quiet, and uses less water. The clothes come out clean and less wrinkled if you take advantage of the settings. l like the extra rinse and the drawer underneath. The capacity is able to accommodate enough clothes so I only need to do a load of darks and a load of whites each week.

After buying this dishwasher model MDB6759WWW3 in Jan. 2010, I fully expected it to work longer than it did! So far, the control panel has been replaced 5 times. The last time was Sept. 17, 2012 and already it is out again. I talked with Customer Service, since Georgia has a lemon law. After 4 times it is to be replaced.They had no record of the part that was replaced, just that a technician had come and repaired (by ordering the same part they had no knowledge of). This time they will either replace or instead of me calling, my lawyer will call. I will never buy another Maytag product and will encourage anyone else not to buy either. My daughter had the same experience with a refrigerator, a piece of junk they did nothing about. By the way, I have an extended warranty plan, which should not even be necessary!

Bought a Maytag dishwasher 2011! Use it 2 weeks, digital board went down had it replaced! Now 2013, the board is down as well as the motor!! Can you imagine I use it once a day, at most 2 people in this house, and it completely breaks down! Thank goodness I have a Home Depot warranty. I would strongly advise against this product that I spent over $500 for 2 years ago!! How they could sell this dishwasher is a mystery.

I purchased the Bravos X washer approximately 13 mos ago. Washer was noisy and has deteriorated since installation. I questioned the ability of a non agitator appliance getting close clean but was assured it would. Not the best if clothes are just moving against clothes. The machine had a difficult time in between adjusting to wash balancing a 3x event upon starting. It leaked intermittently during spin cycles and stopped due to unbalanced loads, sometimes refilling and stopping again. Now it wont spin at all, circuit board problems! This is my first and last Maytag. The company will most likely not balance/compensate on the purchase price (like the Bravos X) because it is beyond the 12 mos warranty.

We purchased our washer and dryer set in December of 2010 and had it for about 2 years with the extended warranty...needless to say around 1 1/2 - 2 years the metal around our bleach dispenser started rusting. Maytag considers this cosmetic! I am shocked to think that its cosmetic...on the outside of the washer yes, but on the inside no! It is faulty on Maytags part. I have spoken with Maytag and they tell me if it doesnt happen within the first 30 days there is nothing they can do. So I will tell anyone and everyone what was said to me via Maytags own repairman, Buy cheaper washers as NO ONE offers an extended warranty on the inside of the washer rusting. Whirlpool is the owner of Maytag now so beware of Whirlpool as well. Check out the warranties and make sure you will be covered longer than 30 days for rusting on any washer you intend on purchasing. We learned the hard way and well....we will be buying a cheap washer like the repairman suggested when this one goes out.

Purchased our Maytag Bravo Quiet Series 300 about 5 years ago and came to this site to read about other washing machine complaints because I am looking for a new washer. Was SHOCKED to hear so many similar complaints to mine (our local appliance store who sold us this unit, as well as services it, said this was unusual). Tiny holes in all our clothes! Black marks on clothes! Dirty clothes! LOUD & BUMPY washing - will sometimes walk itself around the laundry room, slamming into wash sink & dryer (there are dents to prove the violence). UL light that stops the machine & cant be resolved even after I untangle & lift water-soaked items. Finally started seeing black marks splattering out from under machine & was told the bearing is bad and the case (?) is leaking? ... Anyway, result to repair is MORE THAN ITS WORTH.Also have a 3 year old Maytag Quiet Series 300 DISHWASHER, that does not clean well, sometimes leaves half the dishes untouched (dry & dirty), grinds food waste & redistributes onto dishes before baking it on tight (requires soaking to loosen, then wash by hand) ... Oh, and is NOT quiet! I was told I probably use TOO MUCH SOAP. Seriously?!? My complaint is NOT soap residue ... It is D.I.R.T. How can you run a load and still have sauce & ketchup that dripped onto the inside of the door when loading the dishwasher STILL on the inside of the door??? Darn thing cant even clean itself!

I have had my washer and dryer for about 5 years. After a couple of years, I noticed my washer would fill and stop. When I go to put clothes in the dryer, it’s still filled with water... very inconvenient! I have to open and close it and then it continues. The dial doesnt work properly! The delicate cycle hardly works... that started after about a year. It just freezes up and stops. I have to open and close it. It does not rinse right, leaves a film on dark clothes, and I have to rinse again; I do not over fill it either. Sometimes it does smell a little mildew.The dryer knob does not work properly. I set my setting and pull the knob out, and it doesnt come on. I have to do it several times or change the setting or put it on 30 minutes only... very frustrating! I never had these problems with my Kenmores! I wish I did not switch brands. These things should work properly. I realize washers and dryers dont last like they used to, but come on! They also cost so much more than they used to. I wont do this again. I will do more research as to what is a good product. Too bad!

Purchased Maytag dishwasher from Ft Knox Exchange in 2011, Model MDB6709AWW1; Serial # F04117463. Like most posts before me, the panel started failing after 2 years. Unit is now inoperative. I am attempting to fix myself using repair techniques Ive found online as I refuse to pay hundreds of dollars to repair this piece of junk. Will never buy Maytag again.

Maytag Centennial 3.4 top-loader was purchased at Home Depot. It has never worked yet. On 4/28/12, the third weekend, I sat home for the servicemen to fix this junk machine. The first two times, the machine didn’t work ten minutes after they left and today they went to the wrong address. I have much more important things to do than to sit around and wait for someone to figure out what is wrong with this machine. It would have been cheaper for me to junk this brand new machine and buy a washer from a company that makes washers that work!

So far, so very good. This is the first time owning/using an electric oven. I just love my Maytag. It was affordable, especially since it was a combo sale with the over-head matching microwave from Home Depot. Two years later and it's as if I just purchased it. Wonderful, wonderful, wonderful.

The freezer leaks water onto the floor in large pools. Had it repaired, two weeks later, still leaks. Very unhappy with the performance of the bottom freezer Maytag refrigerator.

We purchased our Maytag Bravos washer and dryer in 2008. Within a year, the hinges that held the door open on the top load washer broke. In year 2, the area around the fabric softener dispenser rusted so badly that it almost completely ate the porcelain enamel away. In year 4, it started making a noise that I will compare to a jet on takeoff during the rinse cycles. It continued to work but got louder and louder. We looked into the cost of the repair, which was going to be $350 parts + labor. If it had been a good machine, we might have considered fixing it but it wasnt. Even a set of sheets could put it off balance, which stopped the machine with the wash cycle incomplete. It also set its own water level based on the weight of the clothes and many times the top items came out with dry spots that hadnt even been submerged throughout the whole cycle. Consequently, the clothes were never very clean and I would have to rewash many loads. This machine was not cheap - around $1,000. I was so frustrated and felt completely taken by the Whirlpool company again. We have had many unhappy situations with their products over the years - Kitchenaid, Jenn-Air and Maytag. We finally learned our lesson and researched washers online. The best rated that we could find was Speed Queen. We couldnt find it in Canada, so my husband drove 5 hours round trip to the US and bought one. We have had it 4 months now and the difference is unbelievable. Our clothes are clean again. I can set my own water level and the hot cycle actually gives you hot water. It never goes off balance no matter how many or few clothes it has. If I see that I need more water part way through a cycle, it has a button that lets you add some part way through. It doesnt have a lot of bells and whistles. Its a basic but excellent machine that is a pleasure to use. I would recommend it highly. I realize it has only been a short time, but my Maytag never performed like this machine even from day one. It reminds me of my very first washing machine many years ago, an Inglis, which never had a repair in 15 years of use. If our dryer goes, we will definitely buy Speed Queen. The trip is well worth it.

I could not get parts for Maytag Model MHWE200XW00 Type 832A as the Whirlpool does not provide after sales service. I purchased the new washer in 2010 and lasted for just 4 years. I believe they guarantee supply of spare parts (Inner Basket, Outer Tub and Rubber Boot) for 10 years and more.

Horrible machine. Uses too little water, cycles are too long. No matter what the size of the load, it takes an hour. Just after 3 years the bearing went out on the machine. Cost for repair will be $250. Thats not even an electronic problem which Im sure would be next. NO THANKS. Im getting a new machine and it wont be a Maytag.

I have had trouble since I bought the Maytag Bravo washer. It first started out with the motherboard putting up crazy numbers. It took 2 different motherboards before that problem was fixed. Then it started with not wanting to drain; that was caused from the washer machine sucking up small clothes items in the drain plug. I had to call the Maytag repairman 4 times until I was told I had to put the small items in a laundry bag for this to stop. Now it is going off level on every wash, even when it has only 2 pieces of clothes in the machine. I am about ready to throw it out. Btw, all of my appliances are Maytag and I will never buy another Maytag appliance again or I will never recommend a Maytag to anyone.

After one year, this famous Neptune washing machine began to sound so noisy during the spin cycle that neighbors must have thought a 747 was taking off from our house. After researching the web, I found that the main bearing always fails in this machine and there is a new one-man repair industry started up across the US to just replace these bearings. In fact, someone invented a bearing puller just for this problem. I am deeply disappointed that a once fine company would knowingly put out such trash. I am replacing ours with another brand, even though we have used Maytag for 30 years. Customers always determine who wins and who loses in the long run. Bye, Maytag!

The Maytag washer is very quiet & economical by filling the amount of water needed per load so actually a money saver. Also got the huge drum to wash quilts & blankets. My old one lasted 10++ years. Hopefully get as many years out of the new one.

Maytag has always been my favorite lasts forever no problems at all till something perforated the pump but was fixed promptly. I had my maytag till I moved and left it with my son so I do not have it now but I'd buy another maytag as long as it's not one of those water savers. Do not like those because it doesn't use enough water to rinse out the soap properly like the older original machines. Maytag is strong, durable and worth every penny. If I was buying another washer It would definitely be a maytag. They wash clothes thoroughly. Of all household appliances if have to have a maytag washing machine and my favorite vacuum cleaner. Maytag washing machines are by far a ten next everything else I've tried.

I have a Maytag dishwasher model mdb6759aws3. The control touch pad broke after 1.5 years of light use. It costs $475 to fix (includes labor). Completely unacceptable service provided by Maytag over the phone. The only concession offered was a 25% discount if I bought the replacement part (control touch pad) from them. After some internet research, I learned Maytag marks up their parts prices over 25% so they are really not giving you a discount at all.I filed a complaint with Maytag but they were unable to provide me with any evidence of doing such except for an 11-digit code. Due to a major defect, Maytag should have sent me the replacement part for free. I told Maytag I thought this was fair and that I would pay for the labor. I will never buy another Maytag appliance again! They are junk and the company does not practice common sense customer service.

At first the Maytag Bravos XL top load washing machine met all me expectations. After 3 yrs. the top where you load bleach and fabric softener began to rust. This is not covered under warranty. My last washer was a Whirlpool and had it 15 year and never had that issue. So it cant be from the water, just poor workmanship. Very disappointed. Now my lid came loose and is ready to fall off. Would not recommend.

The middle piece of glass on my four-year-old gas oven shattered. It was not being used, but when I called Maytag, they told me that that was not covered because I did not have an extended warranty, and that I can purchase a new oven door and would have to pay the service person. I hope they go out of business. Maytag stinks, and everyone should know this.

A washer should last 10 years. Bought it in 2009 - after two years we spent $200+ on seal and bearings. Now, in 2014 we need more seal and bearings and the service tech recommended by Maytag says the cost will be $500+. Machine has a serious design flaw, and bad parts, and bad service.

My Maytag 2000 has ripped our clothes. This is my 1st front loading set. I looked on the internet and it seems that this is a known problem. Very upset that a brand that I had for 30 years and recommended to others as well has turned into a terrible company. Im a single mom and Im not in a position to replace a washer every year. I trusted Maytag! A recall and either replacement of the parts, or delivery of new part to fix the problem should have been put in place. I wrote to Maytag to see if they will do something to fix this problem.I have the set, washer shakes a lot, but works well. Washer also always has a lot of water left on the door seals folds, terrible design... I will post on other sites to warn other customers. This is not OK, my clothes are destroyed. See pictures. Clothes got trapped in a gap that exists in the perimeter of the opening, where it meets the door. Why is there a gap at all???

Have had it for 2 years now and its leaked out the bottom since it was 6 mos. old. Now the ice maker has fried a motor and were having to repair it already. Cant believe we spent a small fortune on this fridge and are having constant problems with it.

I bought my Maytag washer thinking that I was buying a quality product. My washer hardly ever can complete a spin cycle without bumping and knocking and then stopping. I have to babysit this washer because we never know if it will complete a cycle or not. The machine is totally level. We have to adjust almost every load just to wash clothes. Sorry Maytag but this washer is crap and I will never buy anything made by Maytag. What a waste of my money.

Maytag fridges, obsolete in less than 3 years. TWICE! My last Maytag fridge dies at about 2.5 years. I called up customer service. It was a compressor not repairable. This was an expensive fridge. Reluctantly we bought another one as the space could only accommodate a Maytag. Again less than 3 years old, the ice maker is shot and the plastic inserts are all falling apart. This time Ill renovate my kitchen for that extra 2 inches to accommodate a different brand.

April 26, 2011, I purchased a Maytag top and bottom fridge from Home Depot. After a few days, I noticed frost starting to form in my frost-free freezer and the fridge wasnt really that cold. I adjusted the dials thinking that may do the trick. Nothing changed, it was all the same and instead, frost was thicker. I contacted Maytag, which by the way was taken over by Whirlpool. I told them my situation and since I had just bought the fridge, I wanted a new replacement. They told me things didnt work that way, that I had to honor the warranty. Fine, we are almost entering October now. I have had several services calls, I have written to the Better Business Bureau, I have lost a few hundred dollars worth of food for it would be full of ice and had to be thrown out, I have contacted the executive offices of Whirlpool but they, along with the Better Business Bureau are not doing a thing. Tomorrow, once again, I am having a service call and once again, I know the issue will not be fixed. All I wanted was to either get my money back, along with extra for the loss of food or for them to just exchange it for another one, since this one was purchased with a problem. I really dont think that its right that they are able to get away with this. Just looking at this page, I see that there are plenty of people with this same issue. What is being done about it? If it were them with this issue instead of us, you know ** well they would have had a new fridge the following day. Here is my model# M1TXEMMWQ and serial# VS04658359 for this fridge. Please, I would really appreciate some help here.

Our Maytag Dishwasher, Model MDB4949SDE2 was purchased May 14, 2016 at Home Depot for $470. It has performed perfectly until January 6, 2020, when a noise, loud enough to imitate grinding wheel, happened with every Start-Up attempt. An independent technician advised replacing the pump motor, thinking that perhaps some popcorn kernels had lodged in the system. (Kernels were cleaned out of the drain filter.)We operated the unit after he left, and the noise began to diminish, eventually disappearing altogether after several loads. Today, February 26, 2020, the same tech found that the large, upper impeller was clogged (not rinsing completely) with citrus seeds and VARIOUS METAL SHAVINGS & SMALL PIECES OF WHAT WOULD BE CHOPPER BLADES FROM THE INTERNAL GARBAGE DISPOSAL. After reading the Maytag Dishwasher problems experienced by others (with repeated control panel failure, burning wires, leaks, and house fires), I consider us lucky to have none of those. We will not run the unit at night, nor with an empty house. Next problem, we will buy a Chinese made dishwasher, like GE.

Absolutely the worst washer I have ever had. I have read some of the other reviews, wish I was smarter and checked this out before spending my hard earned money to buy this washer. My washer also is rusting at the top where the bleach goes. I never close the lid when not in use my basement is dry AND I never use bleach??? My clothes come out they are a tangled up mess. When I go to hang them they are partly dry. It isnt as though I stuff the washer NEVER put more than 8 shirts in at a time yet they all come out with dry streaks like that part of the clothing never even got wet. We all know what happens when you leave a tissue in your pocket and it goes through the washer... Well not with this washer the tissue sometimes came out as dry as it went in. HORRIBLE product. I want the old agitator/I SET THE WATER LEVEL type back. It takes forever to get laundry done. They should take these OFF the market and give us poor consumers some cash back.

I had a 1 1/2 yr old front load washer. I was worried the filter might have a lot of dog hair in it so I called to just have it looked out. I couldnt remember if I had an extended warranty. Thought it would be listed with Maytag. They said no. I said OK. They recommended A+ to come out and said it would be $60.00. That was OK because I wanted to prevent any problems with the washer in the future. I thought them checking it would be a preventative measure. The tech came out opened it up said there wasnt much hair or any other problems. Put it back together, plugged it in. There was a Big popping noise and smoke! Washer no longer worked. The man said doesnt make sense but he would fix it and not charge me for parts etc. I called Maytag. They refused to do anything since it was out of warranty even though they recommended this company and there was absolutely nothing wrong with it in the beginning.After about 2 months he still couldnt fix it. About this time I found papers for a warranty with the Home Depot. The repairman said he works with Home Depot as well. Told me to contact them but I needed to pay $120.00 to him and file a claim and then he would fix it. Apparently he does not do service work for Home Depot. They sent out other repairmen. They tried to fix it but apparently it was deemed unserviceable he blew the mother board. Home Depot said they would replace or reimburse me the amount I paid for washer. Then a machine called said they were sending me a check. We will probably never buy another Maytag! Even though I want to buy American if they wont help or stand behind their products. I now have an LG we bought from Pacific Sales with a cheaper warranty and much better customer service.

My Maytag microwave MMV4205BAB gave out this a.m...again. I bought it in 2008. The repairman has become a close personal friend because he visits so often. In Jan. 2012, I bought an extended warranty, which expired in Jan 2013. This is the best example of planned obsolescence Ive ever seen. We wish we had kept our GE with the broken handle, which we had for 20 years with no other problems than that. If you are wise, do not buy Maytag.

I have had it (Model MDB6000AWB) for a few years now. It had to have the door replaced per recall. This dishwasher does not wash dishes well at all; need to rewash many items after going through normal wash cycle. Also, all spokes are burning and falling off, along with pans getting burn marks. I am not sure how safe this is anymore. I am going to purchase another dishwasher, but not a Maytag!

Code F51 showed up and my appliance repair man immediately said, I see this problem with the Maytag Bravos all the time. Its a control board and motor problem. He gave me a number to call to see if I could receive help through Maytag (Whirlpool), because its a major fix. He also thought that there might be a recall by now since there have been so many problems, but no. The Maytag customer rep was of no help. So disappointed in Maytag and the Bravos Washer. I will never buy another Maytag again!

I purchased an automatic dishwasher for $660.00 on or about Aug of 2007 (Mod #MDB6759AWS3 ser # NY3417703). It was a model about to be discontinued however still carried the full one year warranty. After install one year and 28 days it failed. The tech described a faulty computer board and a replacement cost of $885.00, a cost of $215.00 more than it originally cost!! They did offer a warranty of one year after we installed the new part but at a cost of $215.00 more than we originally paid! Maytag promotes their brand as reliable. However I dispute this claim.

I purchased a front load washer over 2 year ago and the bearing on it has gone bad. Maytag jumped at offering to ship the parts to me at no cost (which at the time I thought was great). I waited 3 months to finally get the part, because it was on back order, and now was just hit with the labor bill! If I would have known a brand new washer was going to go bad after 2 years and cost me over $500 to repair, I would have gone with another brand, In fact, I will never buy a Maytag or Whirlpool. I will ensure that I tell everyone and post comments all over the website about how ** of a product Maytag/Whirlpool produces. Companies like these give the U.S. a bad name! Maytag, you suck!

Purchased my Bravos June 2012. This is a horrible washer. It does not clean. It leaves a detergent scum line on clothing. My work clothes are visibly soiled and sometimes come out in a tangled mess. Maytag ignored a first complaint from my wife. I complained again today. Regardless what Maytag does, I will purchase another brand after research. We bought on Maytag’s reputation.

The Maytag Bravos XL washing machine has a difficult time getting clothes clean. The glass top allows a person to watch the clothing being washed. After one watches this for 5 minutes, it is quite clear that the clothes are not being washed properly. Clothes frequently end up dirty at the end of the wash cycles. I personally believe the design of the agitator is so poor that it is not capable of moving the clothing around to come clean. The tub is a large 4.5 cubic foot capacity, but because it uses so little water it simply doesnt function as advertised. Often there is residue on clothing, simple stains like dirt marks dont get removed. In addition to poor cleaning, the spin cycle is simply bizarre; clothes are twisted to the point that the wrinkles created during this cycle will not come out during the dryer phase of laundry work. I am completely unsatisfied with my purchase and regret not researching this more prior to purchase. I am baffled that this product could actually make it through quality control at Maytag. I have had one service call under warranty to fix the lid not locking. This repair was completed with satisfaction.

We purchased the Maytag Bravos MCT in July 2017. Just passed the 1 year warranty and the glass door just shattered. No reason for it really other than it must have been defective. Nothing dropped on it and it wasnt cold or hot in the room. I got nothing. Maytag said they didnt know why it would happen, and would have to send service tech out. A lid for this type of washer alone is $200-$300. Buyer beware. Dont get a glass top loader.

The lid on this washer cracked twice. It is made out of plastic and is now discontinued. The lid cracks no matter how gentle you are with it. It is just over a year old and will have been serviced twice. The lid has to be ordered and you have to wait for a week. Maytag will not offer a new machine.

After a year or so my Maytag fridge is leaking, I followed instructions on how to remove ice clogging the drain pipe and fixed the problem. I see that this problem is going to repeat over and over again for the life of this unit, because of a poor design.The design fix will be to add a small heater (at the location where the ice creates the clog) actuated periodically by the control board, or at least with a manual push button for the user can easily remove press the button to melt the ice clogging the pipe. This is a cheap design which did not go through design validation and qualification.

The bottom oven of my Maytag double oven range (serial #MER6765BAS18) caught fire while I was baking there. The coil burnt out and separated. This did not occur due to food spill or other means. The coil was charred. The stove top does not perform adequately and the coils do not heat uniformly.

Maytag Dishwasher Model # MDB7749SBM1. What a piece of JUNK! Purchased in June 2013. Control panel went out six months later! June 2014 Control panel BAD again (#2). March 2015 another Control panel replaced (#3). Thank God for Home Depots extended warranty! October 2019.... Control panel needs replacing!

I purchased my first Maytag dishwasher and it was recalled as being a fire hazard. I was offered to have it repaired or pay for an upgrade (approximately $200). I chose to pay and upgrade because I dont want a fire hazard in my home. After my paid replacement, I received a recall on the new dishwasher regarding the same issue (different model) and I chose once again to pay and upgrade (thinking that if I spent $700, I wouldnt have a problem). In less than two months of installation, the dishwasher died in the middle of a cycle. Filled with water, I bailed it out and called Maytag. I told them that I wanted a new one and they told me that I was past the replacement period. They sent a service man out and he stated that it was a problem with model # MDB7709AWB2 and serial # F03002958. He said that it was easy to fix and said he had done it several times. So now, within less than 1 month before my warranty is expired, the dishwasher did the same thing--it died in the middle of the cycle and wont turn on. I called Maytag and they told me that they would send out a third party repair company (JD Appliance) but I would have to wait for four days. I contacted Maytag and said that I was concerned about the dishwasher breaking down again for the same problem (bi metal unit blew). This is the second time it happened. Jeremy, the repair man, said that the first replacement was not installed properly and they should have replaced the entire unit. He stated that it was a common problem with that model, as did the first repairman in Dec 2010. When I spoke to a supervisor named Kia at 800-344-1274, she stated that they had no known issues with this model. I said that it was not what the repairman told me as well as the Maytag dispatcher. They both said that the heat sensor (Bi Metal Thermal Unit Part No. W10258275) goes up and has to be replaced because it is overly sensitive. If you are out of warranty, it costs around $200 to have it fixed. I told Kia and she said that it was not documented in her file, therefore, it never happened. I want to know my consumer rights to address this issue. I have paid for (on 3 occasions) a new dishwasher and have continuous issues that cost me money. I want an assurance like an extended warranty, free of charge, for the dishwasher that has already been repaired twice for the same exact problem. I have the original part that was improperly replaced to prove that it wasnt replaced to specifications, therefore, blowing it again. I was told by Kia that Maytag does not compensate or replace their products unless deemed not repairable by the technician. It doesnt matter how many time the same problem occurs. I would appreciate your attention to this matter.

We purchased this washer 8 months ago, and still do not have a working unit. From the very beginning of installing the new washer we had repeated F4 and E1 error codes. A technician was sent out three separate times and they replaced the ACU each time only to have the same error codes recur. This unfortunately took 5 months as each time the ACU part was on backorder. After 3 failed attempts they agreed to replace the washer with a new one. We were dumbfounded when the new unit arrived and we had the same F4 and E1 error codes! They have again replaced the ACU and still we have the same error codes! They are sending yet another ACU but we have little confidence this will work and we are at a painful 8 months with no washer.

This Bravo Top Loading Washer does not thoroughly clean my clothes. It doesn’t fill properly with water, and it leaves soap residue on my clothes, because it’s not using enough water. I’m using the 2 rinse cycle trying to prevent this, and it’s still not enough. It has actually ruined a few of my items. It is the WORST washing machine I’ve ever purchased. I’m disappointed in Maytag for producing such an awful machine and Sears for selling such a sub par product.

My Maytag Front Load Washer Model MHWE200XW purchased from Sears had a malfunctioning spin cycle. The authorized Maytag repairman from Landers, with support from a Maytag technician by phone, did not know how to repair it. The machine had light use over the past 15 months, and hence was not covered under warranty. So I am out $650 for the machine and $200 for the repair that resulted in continued and even worse malfunctioning. Unfortunately for me, the tests did not show any errors and the machine did not state any error. It just would not spin and then would not allow the door to open. It is a lemon and I do not recommend its purchase.

I have a Maytag Precision double oven 850 series. The upper oven handle does not fit snugly and has been broken 4 times. I have had to order 4 new handles because the hardware does not seem to secure the handle to the oven door. There are no problems with the lower oven door.

We bought our Legacy Washer and Dryer from Home Depot in December, 2005. Luckily we also bought the one year warranty, because in January 2006, our washer quit running. We called Home Depot, we got the runaround and I think Maytag sent someone out. When he tipped the washing machine over, a belt was off. He said it happens. The next year, something else went wrong with the washing machine (not under warranty anymore) and I paid $129 for that visit. Three weeks ago, the spin dry quit doing a good job on the extended spin cycle. Tonight, I put a load of clothes in and though the washer sounded like it was agitating the clothes, when I lifted the top I saw it was just noise, no agitating. I cannot afford the service call, let alone the whole repair or a new washer.

I called. I was told nobody else ever had that problem. She hung up. I called again. The french door is nice to look at but it does not seal properly and there is CONSTANT build up of BLACK MOLD no matter how much cleaning. It returns. There is no other design for a seal either. There are several creases in the gaskets and there is mold in all of them no matter how deeply cleaned or sprayed. The seal is poorly constructed. DO NOT BUY THEIR FRENCH DOOR... Also their ice maker shoots ice all over the floor.

Our refrigerator is just 2 years old and it have been leaking for over a year. It started leaking right when the warranty expired. I am so mad. I called them and they said... You can purchase a warranty for $400. I am like.... what!!! I called my home warranty and they fixed it for $100. A few months later it is leaking again! I am so mad... It is a $1200 refrigerator. What can we do as a group to fight for this? There have to be something that we can do?? It is so frustrating. If there is an attorney that can take care of this group that would be great.

Had our house built in 2009 and the builder carry Maytag Appliances. After 3 years every single appliances start giving us problems. First the refrigerator not getting cold, got it fixed. Then the dishwasher panel, then the built-in microwave, then washing machine. Just the other day the refrigerator broke down again and I was told the compressor was bad. Really? Whats going with this company? All the appliances from this maker dont have longevity. I have 20 year older refrigerator from GE and its still working. Please do not buy this garbage... Its a waste of your hard-earned money.

I bought a Maytag washer in June and its the worst washer I have ever had. It has been 15 yrs since I had to buy a washer. My last washer was a Kenmore which was great. The Maytag does not have a water control knob. It has auto sensing which is crazy. I know how much water I need to wash my clothes. The water sensing barely puts water over the top of the clothes which is not what I need. My husband works in the oil field and gets oily and dirty. The next issue is the agitator that agitates the clothes. This one is a joke. The agitator starts agitating the clothes before the water is over the clothes and then when it needs to agitate it does a poor job. I am so unhappy with my machine that I am getting rid of it and looking for an old type washer. Evidently you made this washer for white collar people who do not get dirty. This is definitely not a washer for people who have dirty laundry. I am so disappointed with Maytag. I thought this was a good brand.

We bought a Maytag dryer and within two years the drum cracked. It will cost over $500 to repair it and then will the new drum be better? I bet not. Piece of junk.

WOW, I cant believe a group of educated professionals made, tested, and approved such a washing machine. What a piece of crap. I could put my clothes in a bathtub and let the kids jump up and down on them and they would come out cleaner. I would love to have a heart to heart talk with the engineers who designed this, to ask, What were you thinking. What a waste of money, and a once good company, that will soon be going out of business.

Less than 2 yrs old and starts giving UL error on spin cycle. I try replacing the springs. No relief. Notice dark brown fluid under dryer. Thing sound like a plane taking off. A little more research and Im thinking its the bearings. Looks like an expensive repair, now I have to decide whether to cut my losses. Seriously? The reviews on here are just horrible, not like this was an dl hell machine.

I have enjoyed my microwave and it has lasted 10 years so far. The only problem I have had is the handle coming off but I clip it back on. Also I changed the bulb. The microwave is over the stove and matched the rest of my appliances. Basically, I would recommend Maytag for any appliances that a person would need to buy.