The Maytag MGR5875QDW oven does not come up to temperature. It might start, but then it will give 2 dings and show a failure. I have called the 800 number in the manual. There’s no good help. I turned the power off and then on. It’s no help. This a pain in the rear end. That is a kind way of saying it. Home phone is **; cell phone number is **. Call me any time. Thank you. You do not want my wife to go on the internet!

I purchased a Maytag Bravos Quiet Series 400 in 2010 and it is now leaking like crazy and sounds like the bearings are going or gone in it. I researched washing machines for over a month before purchasing, and it seemed like this would be the machine for our active family. So much for research. It washes clothes okay, but is a bit rough on them. I found that it has ripped some of my more delicate items. When I contacted Maytag, they sent me an email with contact information to purchase a maintenance contract for $395 which would cover the machine for only 1 year. My husband is very mechanical and took the washer apart thinking the seal/gasket may have come off. He cleaned up the seal and the area around it, and put the seal back on. It did not help. He also noticed that the drive shaft to the motor was beginning to RUST! This machine is only 2 1/2 years old! So, if you are noticing that your whites are getting orange spots on them, this is probably happening to your washer, as well. Maytag should step up to the plate and recall this machine.

Well I must say I concur with all previous posts. I just replaced my Bravos with a Samsung after my jet plane of a washer died. My repair guy said it was not worth it to fix it. I had already replaced the shocks two years ago but I did have mine for 8 years. I have had the same problems as previous posts - rust, smell, holes, broken, too expensive! Hello to Samsung!!

We purchased our washer Model # MHWE450WW01 and Serial # CS10502122 on March 30, 2011 along with a front loaded dryer and refrigerator on March 30, 2011 from a local store Appliance Outlet in Duncansville, PA. As with most new purchases we were excited as all three of these appliances being replaced were 20 years old. All were installed and worked great. My wife and I would often comment that in the spin cycle the washer sounded like a jet engine readying for take off. At some time in early 2014 we had Appliance Outlet come out and inspect the washer and told us that the washer was not to be that noisy and they would authorize replacement parts under warranty. In calling Maytag we were treated well and the parts came. Rear tub W10772619, Basket W10283352, Front tub W102823352.One of the parts was in fact cracked when it came in and had to be reordered. It was and several weeks later it arrived and Appliance Outlet fixed the washer. It ran so quiet we could not believe it was the same machine. In late spring of this year the noise was back. Appliance Outlet confirmed that indeed the same issue was happening and we would need to replace the parts again. In early June 2105 I called customer service and explained the situation and the rep took the notes and stated that we could indeed get these parts replaced and we as homeowners would pay for the labor. As YOU would I tried to get the labor paid for and was given the company line policy and told that there was NO way Maytag paid for the labor and the parts would be shipped. I accepted these terms.Yesterday my wife called to find out the status of the parts shipment and was taken for all intent and purpose right back thru the initial call routine. NO record of my call in early June existed and the best she got was that if Appliance Outlet would call and order the parts that they would be reimbursed. Appliance Outlet said that is NOT normal warranty procedure. Normal warranty goes from Maytag to the appliance Owner. They only confirm the issues/problems and do the labor. I am now stuck. I am also CEO of a company and while it pales in size the buck stops at my desk.

Maytag Frenchdoor MFX2570AEM3 - Was initially really excited with this brand new fridge. We have not even fully paid it off, as we bought with credit at Home Depot, and it continuously leaks water from freezer! I have taken everything out, defrosted, spent about two hours pushing hot water through the freezer drain with a turkey baster and it was only about four days before I had a puddle on my floor again! We have bought quite a few maytag products before, but after this fridge, probably never again! If there is a recall or a lawsuit pending, please, someone advise me of either.

We bought a Maytag Refrigerator, Model MSB27C2XAMSS from BrandsMart on 2/4/2015. Today, I made my 4th Service Call for the Ice Maker not making ice. The service department has replaced the icemaker, repaired it and still does not work. When I call for service I usually have to wait 5-7 days before I can have a technician come to my home. Also, the refrigerator door does not close unless you push it completely to the refrigerator, unlike most refrigerators that I have had. I would never buy another Maytag refrigerator and certainly will make an informed and researched decision before buying another refrigerator. I am truly dissatisfied with this refrigerator and would suggest looking for other brands.

I want to document my experience with Maytag refrigerator model # 1958XEW1 and serial # K12947360. I purchase this refrigerator several years ago as a result of a recommendation of a general contractor who was doing kitchen remodeling work for me. After doing a brief online research on Maytag I went to Yale Electric a store in Boston to purchase a Maytag refrigerator. Worst mistake I ever made and I will never buy a Maytag product again (sad to say). This refrigerator has been leaking since the day it arrived from the store. Unfortunately for me I didnt notice the fridge leaking until after the warranty had expired (my bad). The leak was such as I could not isolate or say it was the fridge because the water would pool in an area that was away from the frig on my kitchen floor. One day by coincidence I actually saw the fridge leak so then I knew the water on my floor was coming from the fridge. I contacted Maytag who mentioned by that time my warranty had expired, however other people who had purchase this fridge model were experiencing the same problem. Maytag said that this leak problem could be fixed by changing the tubing located in the freezer section of the refrigerator to what they called a duckbill type of tubing. So I had that part sent to me and it was installed in the refrigerator freezer area. As you can imagine because I am writing this negative review that the water leak problem was not corrected and there is still water pooling on my floor from this refrigerator. I will never buy a Maytag product again and I wanted to share this experience with other potential buyers of Maytag products.

I purchased high end Maytag washer, dryer, dishwasher and microwave in May 2010. On Saturday 4/25/14, the Maytag Microwave stopped heating. The fan runs, the panel, display, lights, clock, and tray all work. It just doesnt cook. The Microwave was installed in June of 2010. Not even 4 years old. I have tried to troubleshoot via the instructions that came with the microwave, i.e. Check the demo mode is not on. Dont know why after 3 yrs it would be, but checked it. No help. Pulled the plug out and replaced; turned breaker on and off; checked to see if its was locked. Nothing. I then checked the door and I found that the plastic inside panel on the latching side of the door is pulling away from the door itself, which is part of the locking system. The magnetron shouldnt work if the door system isnt closing properly. The latch system is what is causing the door to pull apart. I am wondering now how much microwave exposure my family has been getting from a malfunctioning door? I have had a Microwave, dishwasher and refrigerator made by Maytag in the past. The refrigerator is 14 yrs old and still works fine. The microwave and dishwasher were at least 10 yrs old when I replaced them with the new Maytags I have now. Here is the problem. Maytag is not Maytag Corp. anymore. Whirlpool Corp now owns the Maytag brand. Prior to the old Maytags I had, I had GE fridge which was junk, and Whirlpool, dishwasher, stove and microwave. They were also junk. I swore I would never buy Whirlpool products again. Surprise.

Bought the xl about 14 months ago. NO LIE! Exactly 2 days after the 1-year warranty was up, the xl went down. Drive shaft and bearings. Did Maytag honor the warranty since it was only 48 hours past the expiration? Not just a no but a why are you bothering attitude. My brother and I are above average machine builders. Well fix it ourselves because we could buy a new one to have it repaired. After many hours scouring the web we found the parts. Maytag didnt make a repair kit available to the public. 7 hours plus over $200 to tear it down and to clean the muck trapped at the drain. Then sand-smooth the burnt on metal where the bearings sit. All for a washing machine that sucks at washing clothes in the first place. Never ever again will I buy a Maytag.

This washing machine is TERRIBLE! If I could give it zero stars I would. It broke right after the first year and has been nothing but trouble since. Agitators has been replaced twice. Clothes do not get clean. Do not buy this machine. When I contacted Maytag with my initial complaints they were not helpful. Please save yourself the trouble and buy a different brand machine.

Bought a washer and dryer from Lowes in June of 2016. Have had service on the dryer 3X and washer 1X since. Two person household that uses product a couple times a week. Dryer drum stops rotating / temp control fails / buzzer doesnt work / motor freezes up / washer makes loud banging sound at the end of the cycle every time....sounds like someone is hitting it with a hammer....Today I want a local serviceman to replace the motor but Maytag insists that I have one of their reps come out next Tuesday to examine the product and then go from there. I have been on the phone for 45 minutes trying to get them to pay me $128 for the failed motor that I will send them for inspection. They will not cooperate. They are hiding behind some BS policy. I want to inform you all in case you are contemplating a Maytag purchase. I will not purchase nor will I recommend Maytag to anyone.

I bought my black refrigerator in 2006. It has ice in the door and freezer on left side and refrigerator on right. I have not had any problem with my refrigerator and it continues to serve me well. When I need to buy another one, I will probably get a stainless that doesnt show handprints.

Purchased new about 3 years ago, doesnt clean, ties clothes in knots, leaves white spots from softener that doesnt get wet sometimes after cycle, some areas are still dry after untying. Now error code 51 keeps appearing, service man 4 times replaced rps sensor as directed, nothing changes. Need a chain to drag behind truck, no technical support from Maytag or whirlpool. Old ones of 20 years still worked good, gave to niece. Lucky her.

I purchased a Maytag Gemini April 22 2017 and I am very unhappy with it. The ovens are not working properly. I have thrown away so much food because the ovens won’t hold temperature. The display says it’s the temp. I set it but the temp keeps dropping and rising causing the bottom and top to burn and inside not to cook. Both ovens are doing it. Had a repairman come day before Christmas. He said there is nothing wrong. He said set temp, when preheat beep goes off wait 15 minutes for it to cycle then insert food. I tried this Christmas Day. Oven is still not working and again I threw away more food. I am so disappointed in Maytag. Serviceman is set up again to come out next week. I think I got a lemon. Please. I think they should replace the whole range. It’s not fair. I paid so much for this range and can’t use it.

My dishwasher is 3-4 years old and the control panel is malfunctioning. Cant push a button to choose what cycle I want, it doesnt respond. I went to the Maytag website to see if there have been others with this problem. It appears that there are many other people having this problem. Parts are not available and it seems that Maytag wont do a recall on this product due to the control panel malfunctioning. I have been dealing with this problem for the past few months. I dont think Maytag is worth the money. They want if you only get a few years out of them.

Maytag Bravo XL - We bought the set about a year ago, after high recommendations from the salesman at Best Buy. This washer does not clean clothes - they come out with soap & spots & white stuff, even after I use the deep water or the extra rinse cycles. These cycles take well over an hour. When they are finally finished, my clothes are twisted into ropes that have to be unwound & taken apart before putting in the dryer. I hate to think what its doing to more delicate clothing, getting stretched & tied up like that. This washer is awful - cant wait to get a new one. The dryer isnt much better - cant believe a $900 dryer doesnt have a steam refresh cycle! And the controls are so touchy - if you actually push them, they dont work. If you lightly hover over the button & barely breathe on it, it does - very strange.

Bought a Maytag bravo xl washer and dryer two years ago. Spent around 1,500 dollars. Didnt make it a year before things started going bad on them. First the lid lock on the washer broke. I got the lid lock pulled out far enough that I could drill a hole in it and tie some thread to it to pull it out when the washer was ready to lock. Today the piece of junk just quit. Not long after the junk washer started messing up the dryer starts sounding like a fork in the garbage disposal. It still works and dries the close but you hate to even turn it on because of the noise. I will never purchase anything maytag again in my life. JUNK!

Two years ago I purchased a Maytag Top-Loading HE Low-Water washer. I have always taken great pride in the way my laundry looks and smells but since this purchase, my laundry no longer smells clean and fresh nor does it look clean. I have always used the same detergent and fabric softener (only now I use the HE version) and it served me well. I have read all of the directions and did as I was instructed. I cannot believe that anyone would actually think that you can do laundry with practically no water. Do the decision makers have not common sense at all? I didnt and still dont believe it but what choice did I have when all of the machines are now HE with low water. I think its terrible that consumers dont have a choice. I have come to realize that low water, HE washing machines actually waste more time, energy and money (detergent and fabric softener).My clothes are not clean, nor do they smell good when the wash cycle is finished so I have to wash them again, using more detergent, fabric softener and energy. The super fast spin that supposedly sucks out most of the moisture, also rumples my laundry with semi-permanent wrinkles (even on the low wrinkle setting) so clothes that never had to be ironed before, now need pressing. I find it remarkable that, with all of the detergent ads promoting washing clothes in cold water to save energy, we are told that if our clothes are not sufficiently clean in cold water in our HE washers, that we should try a warmer/hot temperature. Good luck with that because my machine has several temperature settings but only uses one - COLD! I cannot actually believe that with all of the technology that our society holds, we are going backwards in the basics of washing clothes. Terrible product, terrible quality, terrible results, terrible waste of time, resources and money. Why cant you just leave some things alone??

Dishwasher MDB7749SBM - Have the same problem as everyone else, panel board (2nd one, 1st was under warranty). This panel W10475787 is 2 years old. Keeps lighting up doing what it wants to do. Dishwasher is 3 years old. Cant find out if there is a recall on this part (there should be).

I purchased the Maytag dishwasher a little over two years ago (MDB6759AWQ0). This was the first Maytag product I bought and it is definitely the last one! It was more expensive, but because of Maytags commercials on what good products they had, I thought it would last longer and work better. Boy, was I wrong. When it was installed, it was loud. I brought this to the attention of Maytag. I was told there was nothing that they could do. Repair people were sent to my home several times to see if the noise could be fixed and unfortunately, it could not. This is the loudest dishwasher that I have ever had. I should have stayed with the same brand that was over 10 years old that died! Now the control panel blew out and will cost over $300 to have it fixed. After reviewing the numerous complaints that you have on your dishwasher with the control panels not working, I would think Maytag would be more financially responsible in helping the people that have your products that no longer work after being less than three years old. Just a heads up, Maytag, I will be replacing instead of fixing and not with another Maytag product!

We currently have had our Maytag washing machine for approximately 15 years. The first thing we noticed was how user friendly it was. Also, the options that came with our washing machine met all of our needs. The second thing that we were excited about was how quiet it was. Our previous washing machine could be heard at the back of the house and was constantly out of balance. The third thing we noticed was how much cleaner our clothes were. Our clothes smelled better and had less wear thus saving us money. Speaking of which, the machine is an energy saver. One of the most significant attributes I can attest to is how reliable it is. There has never been an issue that required repair services. I am sure our Maytag will be in service for years to come. c

We bought a Maytag refrigerator around 2 yrs ago. Ive had repair out a couple and tried to take care of this myself. I am being told by repair men that it is a design flaw that the line gets plugged and water pours out all over my floor. The refrigerator I replaced was 20 yrs old, never had a service call & never poured water all over my floor. From reviews Im reading Im not alone in this problem. Needless to say Im less than happy with Maytag at this point! Model #:MBF1953YEB3, SER. #:K22812455, reciept #:** pd 1/19/13 DECKER & SONS 430 FULLER GRAND RAPIDS MI.

I bought a Maytag dishwasher in 2019 in Home Depot for my new home. The dishwasher stopped washing dishes after two years and 6 months. The price of the new machine was 700$ and I did not buy the extended warranty. The trouble is circulation pump, that cost to install the new one from local service would be about 350$ plus the new pump 150$. I consider quality is very poor if the new dishwasher works only two years and then it is better to buy a new item than fix the old one. Never never buy Maytag production.

Last August I bought the Maytag Bravos XL. I have had 3 repairmen try to fix my problems with it and they cannot. The problem is, they cant fix an appliance that isnt designed correctly! Without water, one cannot wash. Dont be mislead that the huge area inside can be used for large objects like sheets and comforters. This machine is MUCH harder on my sheets and comforters than my old machine with a center agitator. I have shredded rugs, holes in sheets, black lines on clothes and a chlorine dispenser that puts spots on everything. The detergent dispenser hardware is rusted as well. Folks if this machine was an automobile, IT WOULD BE RECALLED!

Had a brand new Maytag MDB4949 dishwasher installed on 10/20/15. Noticed an acrid smell of burning plastic coming from the pull handle. After going to the reviews I see a pattern of shorting control panel boards melting the ribbon cable. Having repaired Xerox copy machines for 17 years, I recognized the smell of an electronics short and melting plastic. There are 600+ complaints for the same thing. Going to call the store we purchased it from and will escalate from there.

I have only had this machine a few months and am completely dissatisfied. It sounds like a jet taking off and uses so little water. The clothing does not come clean and wrinkles are close to impossible to iron out.

This washer stops every 10 minutes, sometimes taking 3 to 4 hours to complete one spin cycle if it is completed at all. All troubles began shortly after warranty expired. NEVER EVER will I ever buy Maytag again. I make certain that I tell everyone I come in contact with about the pathetic quality of Maytag.

I bought a Maytag side by side fridge freezer in 2010 at a cost of £2000. Having come back from a week away it had entirely defrosted spoiling all the contents. An engineer came to look at it but said the fault was unrepairable so he wrote it off. Maytag (Whirlpool) think that it is perfectly ok for a 5 year old fridge freezer costing two grand should now pack up. I, on the other hand, do not... They offered me £700 of the cost of a new Maytag. Joy! I thought. However, this one does not make ice or have chilled water (the principal reason for buying Maytag in the first place). I was then told that this was the ONLY fridge freezer in the entire Maytag or Whirlpool range. Is there nothing else you can do to help? I pleaded. No was the reply. The moral of this story is going posh on an American Fridge freezer is not guarantee that you will get the after sales service that the price would suggest.

Bravos XL Washer and Dryer (Maytag) is the worst appliance set ever. Not enough water in the bin, residue despite using the correct detergent, and clothes which do not even get fully wet during the wash cycle. I am so sorry I purchased this pair - I do like the heavy duty spin, and the dryer does dry (but the door clasp has somehow come loose and stopped working - has to be wiggled into place every time I close the door). The really frustrating part is the low water levels (and even bulky is less than a half a bin of water. I am attaching a photo with two sets of sheets, a towel and three wash cloths). Most cycles only put about two inches of water in the bin - appalling. And the long long long cycles - what is energy-saving about having to do a load twice and using more than an hour for one cycle? I wish I could adjust the water levels. Seriously disappointed in this duo. Sorry I wasted my hard-earned money on it. I was seduced by a pretty exterior.

Maytag Refrigerator Model MFI2665XEW6 piece of junk. * Builds up ice on bottom of freezer * Bottom freezer door will not close * Annoying alarm sounds* Water leaks on floor

I just purchased a Maytag Washer and Dryer. I am very pleased with the cleaning ability of this washer. It has set pre-timed washing and drying times. I would like to have availability of setting the times for a load to run. Same with the dryer. The book says you can do this but I have not figured out how. I have been very pleased with their abilities to do what they are supposed to do. Cleaning and Drying.

1. can not get enough water in the Maytag machine to cover the clothes. 2. All of the clothes come out twisted. 3. After watching the machine wash the clothes I notice that agitator did not move all of the clothes down into the water, and that was probably because there was not enough water in the tub. 4. The machine gets out of balance easily and at that time the machine door is locked and you need to push the pause button and wait for it to unlock the door. 5. Its louder than my old Kenmore washer that we have had for 15 years.6. The Maytag dryer does not dry as fast as my old Kenmore dryer that we have had for 15 years.Bottom line is I would not buy another Maytag product. Do your homework.

Control panel on front of dishwasher quit. Unit is 15 months old. Bought extended warranty through Home Depot. Took two hours on the phone to finally get to the correct department, they set an appt. for the following Wednesday between 10-2. Had to take a vacation day. Get a call from the appliance repair co. the night before stating they cant live by Depots schedule, they wont be out til the following Monday between 9-1. Schedule a vacation day. They come out then have to order parts, they wont be in for 7-10 business days. After 12 business days, I call back and they set appt. between 10-2. Schedule vacation day. They come out and the control panel the warranty company sent is the wrong one. Now I have to start the whole process over again. DONT BUY MAYTAG AND DONT BUY WARRANTY OR APPLIANCE THROUGH HOME DEPOT.

We purchased the Maytag Bravos XL MCT washer and dryer in July of 2013 and have been completely and totally dissatisfied with every use since. We immediately contacted the store where we purchased them and were told we had to contact Maytag. We contacted Maytag on numerous occasions only to be read ridiculous solutions from a notebook that were no different than the instructions in the users manual and never worked. We had our first set of washer (with agitator) and dryer for 23 wonderful years. The washer absolutely does not work. The decision to remove the agitator and reduce the water levels is absurd. The soap does not get distributed, the lack of water causes loads of clothes or sheets to get rolled up into tight balls with no hope of being cleaned, and the spin cycle is so powerful it rips your clothes apart unnecessarily. The dryer is smaller than the washer and cannot handle the same size load the washer can put out and typically requires more than one cycle to complete a drying. All in all this has been the most painful experience we have ever had with any appliance. We are completely dissatisfied with both the store where we purchased these units and the complete and total lack of response from Maytag after requesting either of them to take back these units or make some equitable adjustment so we could purchase different units. We have reached a point where we will most likely store these Maytag units in the garage and purchase a new washer and dryer, being forced to accept the financial loss.

I think that I finally figured out a way around the piece of junk Maytag sold me. I bought a Maytag french door, stainless, yada, yada refrigerator in 2006. When it broke down, see later description, the first several times it was ok because of the warranty. This POS has failed 7 times requiring $300+ to fix every time. When contacted about the issue, the people at Maytag seem happy. The business model is working perfectly. There goes another sucker. The refrigerator begins its eventual breakdown with the door alarm light and sound beeping constantly. Beeping that continues for days and weeks. The next progression to failure continues with it not beeping anymore but now the interior lights do not light when the refrigerator is opened. Finally, the refrigerator stops cooling entirely and it is dead.Now, Maytag no longer wants anything to do with it so you need to call a repair man. When the repair man arrives, the entire time he talks about what a piece of junk Maytag is. They, every time, at first think it is the switches and replace them. This NEVER fixes the issue. Next, they have to replace the computer brain. $400 to fix. EVERY TIME. Now, at least every year. If you buy Maytag and have a similar experience, get your wallet out. Sell you junk then dont stand behind it.

The ranges are getting great but are more so with digital than buttons and knobs which they should still have, especially for the handicapped and some elderly who prefer them. It would help prevent injuries. It was hard for me to find the knobs.

I bought my Maytag Neptune washer and dryer in 08 or 09, and it has smelled like mold and mildew for years but I still have to use it because I cant afford to get a new one. I cant get the smell out. Also, I have to take the pump apart at least once a year due to the fact that sometimes, no matter how you check your pockets, change still gets left behind and they dont make a screen or filter that will keep the change out of the pump. It is not hard to do, but the first year I had it, it were in the service center as much as it was home. I was glad when someone told me what was happening because I fix it myself in like 15 minutes and move on. But it should come with a self service manual showing how to do this procedure to save people money.

We bought the Maytag Bravos Washer and Dryer set in 2013 after extensive reviews as well as the brand recognition to replace my at least 20 year old Kenmore washer/dryer. At first we were very pleased. The ability to do bulky loads was great and the high spin cycle left the clothes almost dry. In 2018 (keep in mind, just 5 years!) we started to hear a grinding sound in the washer when on rinse cycle and the dryer would randomly turn itself on! Strange but true. I called Maytag Canada and they sent someone right away. They had to replace the motherboard on both the washer and dryer as well as the drum and gears on the washer. Fortunately this was covered under warranty.Fast forward 1.5 years. Same issues with washer...technician came and could not identify the problem, although I did tell him it was the same as 1.5 years ago. I ended up recording the sound and asked them to resend technician to the house. After further diagnostics, yup...same problem. Two days went by and I received a call back advising me that the cost to repair would be over 700.00, not covered by warranty! I escalated to management, to no avail although they did offer me 15% off my next Maytag purchase! Needless to say I have ordered a brand new GE from Costco, arriving tomorrow for basically the same price to repair the Maytag. I will NEVER purchase another Maytag product and will advise anyone who cares to listen to me to do the same. Huge disappointment in the Maytag product, brand name and customer service. 10 year warranty? Not likely...stay away.

The first washer my husband and I ever purchased was a somewhat cheap top loader but it worked very well for over 10 years. We decided to fall for a bargain sale at Home Depot and went with the HE Bravos model. We were told that it would save us money and work great! From day one weve had issues. It never really seemed to clean right. It gets thrown off balance if you have more than one bath towel in a load at a time. After an angry call to the company and a somewhat helpful customer service rep, I began washing every load at the deep clean heavily soiled cycle and then did an extra rinse to boot. So much for energy efficient. So, fast forward 4 years, I HATE this washer but cant justify a new one at this time. Now, it stops mid cycle and I have to unplug it then plug it back in and restart it. When this happens, there is an awful smell. Needless to say, well be buying a new washer within a week or 2 and you can bet your life, it will NOT be a Maytag.

Here recently I got a bravos washer x series because it suppose to cut down water usage. Well that it did. Now going on 7 months of having it now its starting to act up like when the cycle is done it will lock again and repeat the cycle all over. I use the normal or powerwash cycle and here recently how its suppose to sense the load and then start spraying the clothes with water and detergent. Well not here. Lately it still senses and spins and then starts filling up like its on the bulky/sheet cycle but its on normal cycle and it doesnt fill all the way up - just 4 or 5 inches of water. So I dont know what is up with this piece of crap and why its acting this way. Other times it will work fine on the normal and the other cycles but now its just acting all crazy.

I bought my Maytag washer and dryer in Monroe County in Georgia, USA in 1980. Its a 1979 product and it STILL works perfectly fine after 40 years! Im 64 years old now and Im hoping Ill never have to buy a new set although I would love one because theyre so pretty these days.

I have had a few dishwashers in the past, however this is the worst product I have ever purchased. After a couple of years in service I needed a new control panel which cost $200.00. The dishwasher defaults to heated dry and the exhaust for the dishwasher is right behind the copper electrical runs so it corrodes and fries the runs. The way I see it Whirlpool and Maytag saw a unique way to gouge its customers for parts. They also have a rope and plastic cable system that attaches to the door spring that continues to break cost $28.00 a piece, I have replaced two. Now I see that one of the pulley guides (plastic) is broken and split cost??? Here is another brilliant engineering feat, the door panel clips into the control panel so that when the door is pulled in a normal fashion it comes loose. If you buy this line of dishwasher (p.o.s) plan to work on it and buy parts on a constant basis. Here is my advice: buy one control panel, two cable systems, and a couple of cable pulleys or buy a cheap dishwasher as a replacement and save some money. Run from Maytag or its parent company Whirlpool - let the buyer beware.

We bought this washing machine 2 years ago and I was never really satisfied with how it cleaned the clothes. Darker pants would come out with white soap/water lines on them. The worst part, 2 years in, the washer basket seal failed and the bearings rusted. The washer sounds like a tornado every time it runs. I got a quote for $350 to repair it!

Within a year of purchasing this washing machine, I needed to schedule a repair service because the washer started making an unfamiliar noise. Repair Service shows up and refuses to touch my washer. The ink on the Serial and Model number (stick on label) inside the washing machine door has washed off. Sticker label in excellent shape, except all the ink has come off. If the Repair Serviceman cannot read the label, NO SERVICE FOR YOU. MY SAGA... Did you know that if your washer or dryer does not have a readable serial number on the machine, NO repair service will work on it. It does not matter if you have all the paperwork showing this information. If the original label is unreadable, no repair service will touch it because they will be fired. Maytag changes parts on a model all the time. The serial number is the ONLY way a serviceman can tell exactly what parts your washer was made with. Apparently the serial and model number label sticker was not printed with permanent ink. The Repair Service said the Serial and Model number ink washed off the label because the sticker was incorrectly put on the inside of the washer door at the bottom. But they were WRONG! Maytag shows online that is exactly where the serial and model number sticker is supposed to be located. So, I called Maytag to order a new serial number (stick on) label for our washer. I gave Maytag the information and I was told I would have the label in two weeks. Then I called back a week or so later to make sure the serial number was ordered and on the way. Maytag said there was a misunderstanding, and that they received my request on 6/17/15 and it was sent to the ONE AND ONLY GUY that makes replacement serial number tags and he was sent my request on 6/22/15. Maytag said it would take the one and only man quite some time to make the label (SINCE THERE IS ONLY ONE!!!) and I could expect to receive the replacement label in 4 to 6 weeks and they were sorry, but there was absolutely NOTHING they could do about it. So as my year old washer sits for over a month, Im going to the Laundromat each week. We should have received the new serial number on August 6, 2015. So it’s taken almost 2 months and my label is close to two weeks late. To date I have not received my serial number. I tried to use MAYTAG chat, dont bother, they said they couldnt help me. I needed to call in. So I emailed Maytag today for their support services to tell me WHEN I can expect to receive my new serial number label. I bought this through hhGregg. Check your Maytag washer. IF THE SERIAL NUMBER AND MODEL NUMBER LABEL ARE INSIDE THE DOOR, CHECK TO SEE IF THE INK IS COMING OFF THE MACHINE LABEL, and order a new one NOW if it is, or you will not be able to get your washer serviced. Do not put new label back on the inside of the washer door. This is just unbelievable.

Last week I noticed that my freezer motor had a build up of frost. I melted it with a hair dryer. 2 days later there was a layer of frozen water on the bottom of my freezer as well as a layer of water on the first shelf in the fridge area. There is no way to access the drainage tube. I thought that the coils needed to be cleaned. That was not successful either since the coils run horizontal and only the front section can be vacuumed. Today, again the freezer motor area is frosted and layer of ice on bottom and the motor is making a terrible noise. How disappointing for a less than 2 year old fridge.

We had a Whirlpool dishwasher for 24 years, and when it was time to purchase a new one, I did a lot of research before choosing our Maytag. Reviews by other consumers who had purchased dishwashers was very helpful in making our decision, and we have had no problems in the almost 18 months that we have had this dishwasher. It is very quiet. It washes and dries the dishes with no streaks, although I wash off the dishes before loading them. It provides 5 cycles and 4 options and lights blink, when the washing and drying cycles are complete. I would recommend the Maytag, Model #MDB4949SHBO wholeheartedly.

Purchased a Maytag side by side MSB27C2XAM00 in June 2014 to replace a 20 year old Kenmore. After 14 months the fridge stopped keeping things cold in the food compartment and in the freezer. And, the water and ice dispensers stopped working. Called Maytag and they confirmed the fridge was 2 months past the warranty and the best they could do was offer an extended one-year warranty for $325 and set up an appointment. I declined and called a local repair company. They responded promptly and discovered the problem was a bad board. Had to replace the board at a cost of $475 (parts and labor). It was $150 more than the extended warranty but I was already in the hole for $100 service call and I was able to get the fridge repaired on the spot. I had the Kenmore for 20+ years without one repair. Maytag was good for one year and 2 months. Dont know how this company will last with a $2000 product that lasts a year. I can not recommend this product and advise anyone in the market for any appliance to avoid Maytag products.Updated on 11/20/2015: After the board was replaced, the fridge worked but was not keeping either of the side by side compartments cold. They were cool but not cold. Repairman returned. Said it was the compressor which needed to be repaired/replaced. Maytag said the compressor was under a 10 year warranty unlike the other parts of the fridge. Good news, Maytag covered the cost of the part / but bad news that it broke after 14 months of use. However, the service people told me the cost of the compressor was the smallest part of the repair. Labor and service would be costly and Id be better off getting a new fridge with a 5 year warranty contact. After I got over the initial shock of having to toss a 14 month old fridge that cost $1500 and complaining to Maytag, I went to Lowes and found a replacement fridge. This time it was not a Maytag. Moral of the story stay away from Maytag. Dont be fooled by the brand. Avoid them at all costs. And purchase a fridge with a 5yr+ warranty contact!

My refrigerator is several years old, and I would buy the same brand when I need a new one, although I would hopefully buy a counter depth one because my kitchen is so small, and the one I have now is kind of big for the space.

This so called high efficiency washing machine, and others like it are absolutely awful. They do not properly clean clothes. I frequently have to put loads of clothes through two or even three times in order to get things cleaned properly which our old washer did easily in one wash. That is the exact opposite of efficient. It is so bad that it actually borders on being a genuine scam. Do not buy! Huge waste of money.

Purchase of what we thought was high quality Maytag dishwasher. Paid $600 and $250 to get it installed, which was really just to take out the old dishwasher we wish now we had kept, and plug in the new one. After 2 years, repairs needed to replace the control panel and key pad must be replaced, cost $340 plus labor. We will never buy Maytag again. Called their hotline, 800-877-6777. They cannot offer any help. Called the co. we bought it from, a Maytag dealer, Haleys Maytag of Antigonish, Nova Scotia. They too offered nothing except to sell us parts... control panel and key pad. Called lawyer who has class action suit now against Maytag, Eppsteiner & Florica. They are not representing customers who live in Canada, only U.S.My recommendation to Maytag dealer who only sells Maytags, Haleys Maytag of Antigonish, Nova Scotia, find another company to represent. Maytag is a real loser. Never again purchase a Maytag, and I told 10 people who will tell 10 people... who will tell 10 people. Our model number... same as all of yours... the loser MDB6709AWW1. Dont waste your money buying this overpriced dishwasher that will then require you to spend more money every 2 years on a Control panel and Key pad that are defective from the factory.

I purchased my Maytag washing machine in June 2011 and within the first couple of uses, noticed that my clothes did not appear clean. I went back to Home Depot and complained and was told I had to use HE laundry detergent and I was. I gave it a while longer and still, nothing I washed ever seemed to come out clean. Sometimes, the fabric softener dispenser fills with water; other times the fabric softener remains in the dispenser. The machine makes very loud clunking noises during the wash cycle. I knew this machine was a lemon from the get-go. I should have insisted that Home Depot come take it away. I will never buy a Maytag appliance again! Maytag should have recalled this washer long ago and, if there was a Class Action law suit, I would surely join in!

Front load washer unit does not respond to control inputs. I have called Maytag service and support. One can find a repair or maintenance manual. Im in a smaller market so there is limited service. Maytag service and online support is terrible. Maytag stores are fronts for independent service companies. Its probably okay, but misleading. Everyone wants to order the main controller board. It would be good to have a maintenance manual.

Ive had this Maytag for more than 15 years and it still works well. Its a basic fridge, no special features. Just keeps food cold or frozen. Freezer at top, fruit & veggie bins at bottom, cheese bin. No problems, good performance.

Purchase date of Maytag dishwasher 12/9/11 for $651.37. Controls broke 6/2013. Used Maytag specified repair service at cost of $450. New control panel installed 7/9/13. Control panel broke again 8/13/14. WILL BUY NEW DISHWASHER. NOT MAYTAG.

I had a stroke last year in August and my children got together and bought me a washer. And after the third use this thing started messing up and I had to call in someone. Now the warranty is up and I am sitting here with a new broken down machine.

Maytag dishwasher model MDBH979SAM1 purchased December 2012 From Home Depot. After only 14 months of usage the front panel ceased to work. Contacted maytag about issue and they responded THERE ARE NO KNOWN ISSUES WITH THIS MODEL. After doing some research (5 seconds), I have found thousands of people with the exact same issue. Maytag has stuck their head in the sand. Either they are ignoring this issue or just dont care due to excessive cost of replacement. This is obviously a design flaw due to poor engineering and Maytag needs to stand behind their product and fix this issue. Personally we had to save up for 1 1/2 years in order to afford a dishwasher. Now we are stuck. Some people have replaced this part costing $200 2-3 times. I cannot afford to take the chance on a repair. I will have to start saving again for a new dishwasher and this one will not be a Maytag. (Less)

I purchased both a Maytag washer and dryer and I am very disappointed in both products. Both appliances have electronic controls and are substandard. For the dryer if you do not touch the start area exactly right it will not start, can take multiple tries. For the washer, my town turned off my water to switch out the meter, once done the washer did not know how to clear the air in the lines and gave a LF error and no one at Maytag customer service could help me solve the issue and then could not set up a service call as their computers were down and did not have a process to call back the customer. This is terrible Customer Service - never again Maytag or any of their other products????

Stay away from this product!!! Lets just say one star is too much for this product. Terrible. Lets just say one star is too much for this product. We bought this washer 2/2017. We used our previous Maytag washing machine for about 15 years without any problems. But this machine on the first try was a big disappointment because it did not wash clothes very well. Clothes come out of washing machine smelling bad and you could see the soap scum on darker clothing. We try to return the machine to Home Depot after 3 days, but they said after 48 hours they could not take it back. So if there was any problems we had to call a technician to repair it. Well, there is nothing to repair because thats just the way the machine is designed to conserve water.Worst washer and the customer service is even worse than this machine because they just keep repeating that if there is nothing to repair then, there is no problem. So, therefore its not their responsibility. TERRIBLE!!! I even bought their extended warranty and that doesnt do anything with dissatisfaction on this product. If you are owner of this company or at least care about your company, you should stop making this kind of product, and listen to peoples complaints!!! What a waste of our hard earned money in this bad economy!!!

We purchased our French Door, bottom freezer in April 2010 after a renovation. We have loved it besides needing more refrigerated space. This past weekend I noticed the appliance was cutting off and a few seconds later coming back on. It has an outside ice and water dispenser as well and the lights will blink on and off of course when the fridge cut off. Called for a repair and when the repairman called in the parts he was told he needed 2 computer boards. One was available however the other was discontinued and they would not allow him to just replace the one board. The fridge cost us $1798.00 from Home Depot. I cant believe how irresponsible Maytag is in this case. I have a kitchen full of MAYTAG appliances and have loved them all. But this is unacceptable. The Maytag fridge I had before was 16 years old. I gave it to a family member when we bought this one and that one just broke down last year so it was 21 years old! Whats up MAYTAG?

I have a Maytag washing machine (MDBTT53AWW1). The total cost is $524 for machine plus installation. And the cost of yearly repair on this machine is $300.I purchased this machine a year and 10 months ago in January 2010. A few months ago, the control panel started to only light up partially but the washing machine continued to run. A few days ago, when i tried to turn on the machine, it would not work--the control panel was no longer lighting up. I called a repair man recommended by Lowes, and after explaining the problem over the phone, we scheduled a time for him to come (ten days later was his first available opening!).Ten days later with a broken washing machine and doing all the washing by hand, the repair man came late. When I made the appointment, I was told he would come anytime from 8 to 11 a.m., and of course, he did not show up until almost 1:00 pm. When he finally arrived, all he did was look at the model and determined instantly that the reason our control panel was no longer working was due to a faulty design. This dishwasher allows the steam to escape through a small vent placed to the left of the control panel. The steam inevitably causes a short circuit, meaning that this will be a reoccurring problem every year.He did not dismantle anything and was in my home for no more than 5 minutes. I was told the cost of a new control panel would be $141 plus his labor fee of $137. So all in all, if you purchase a Maytag appliance, the initial cost is irrelevant. If you purchase a Maytag appliance, you will spend almost $300 yearly to maintain it--basically the cost of a brand-new washing machine.Something needs to be done; this is unacceptable. The least Maytag could do is provide all of us, fools who believed in their product and thought that they were of quality, with a free10-year warranty for this faulty machine which is pre-determined to break down every year as a result of their poor design planning.Cost aside, what kind of world are we living in that major appliances are made to last just one year and then are to be thrown in the dump? There is no way I will pay $300 for the next ten years to maintain a product that is made to break. That is wasteful and disastrous for the environment. Shame on you, Maytag. You will be filling landfills around the country with your terrible products, and the world will be a worse place for it.

We bought this brand new washing machine just 6 years ago. Went with a Maytag because they are supposed to “last forever”. Ha! Last weekend it stopped spinning. Water would drain but no spin cycle. Had a recommended repair person come out and he said it was unfixable. The bearings were shot. This is crazy. There are only two of us using this machine how could it be totally unfixable 6 after only 6 years. The average washing machine life is supposed to be 14 years. No more Maytag for us.

We have owned a number of dishwashers, some cost a great deal and some were inexpensive. Our current dishwasher is a Maytag and it has proven itself to be the best dishwasher we have ever owned, not only is it quiet, it cost less to operate and cleans all dishes and utensils excellently.

We purchased a brand new Maytag washer dryer and had nothing but problems with both. After talking with corporate several times, trying to reach the CEO, the customer service person told us that the problems were buyers remorse. Needless to say we will never purchase another Maytag/Whirlpool product as long as we live. We are going with Electrolux!

Unbeknownst to us, our Maytag Refrigerators (MFD2561KES) ice maker developed a problem with the fill hose which connects to the back of the refrigerator, causing it to pop off. The hose had been leaking water onto our wood floor causing all of the boards under the refrigerator and 6 feet in front to buckle. I cannot see why Maytag did not use a compression fitting instead of using a squeeze type hose clamp. Plus the ice maker has left a large sheet inside the freezer on the bottom. I use the ice maker daily to fill my cooler for work.We also have a Maytag Dishwasher which has a push button panel in front which has decided to give out as well. Not to mention our Maytag Double Oven which has never been able to close properly since we have had it. (The service man said that there is nothing wrong with it). We bought our house 7 years ago and my wife wanted nothing but Maytag because of our experience in the past. I gave up buying american automobiles years ago and I guess the same will happen when I replace these appliances (after I finish paying for my new floor).

Bought Maytag Bravos in 2010. It does not clean but worse than that it rips clothing (for example: loops off pants, holes in pjs, tons of ripped towels), so many items of clothing torn that I cant keep count. Today I had a pillow case ripped apart (see image). I have had four sheets ripped that I can no longer use. Maytag should have recalled this washing machine. I have the Maytag Bravos dryer also and the drum was on backwards on it when I bought it.

Bought a new maytag gas range march 2013 model #mgr8674ab. The oven would not light at all. Would just click. Still under warranty. Called the service. They came and had to replace the controls in back. 2 months later the same thing, only this time it comes on and goes right back off. Then a week ago got it to light, used the oven and tried to turn it off and it would go off but immediately light up again. Scary to say the least. Another call to service. They are coming tomorrow. This is November 12 2013. I would not buy another maytag gas stove. There is something terribly wrong with this model.

I have never been so disappointed in purchasing an appliance for my home. The Maytag Bravo XL large capacity top loader, has never worked properly, and I have many ruined pieces of clothing. Although it has a very large capacity, the water barely fills to a 1/4, and clothes are sticking out of the water, while they are supposed to be submerged/being washed IN the water. Clothes come out of the washer smelling foul. WORST WASHING MACHINE EVER.

Bought a Maytag dishwasher model MDB7749AWM2 on 02 Jan 2012 with no issues whatsoever until three days ago when it stopped working altogether and after doing a series of tests I discovered that Im joining a large and growing list of owners with the same problem. I never have been a fan of digital controls due to their vulnerability to temperature and humidity conditions or high impacts for that matter. Ive owned many dishwashers of various brands for upwards of 10 years on average each. This is the first one not equipped with analog/mechanical controls. Im hoping I can still find more of that type.

Never dies, never have had to have it serviced. House burned down is reason why it died. So I rebuilt, bought another one, then moved took it with me, then left it with my daughter and moved to Mexico. The dryer is still working to date and this all happened over 10 years ago. I sooo want another one. Best brand period. I only buy Maytag as they last. Unfortunately I do not have one now as they were unavailable in this country so bought something different. I was told the machine I have currently was as good as a maytag - they lied. I recently found out they have them now, so when I can afford one again, I will purchase one.

I had a problem with my 1 year old oven. I scheduled an appointment and no one showed up. So I fixed it myself. A week later they called to schedule an appointment and I told them that they were scheduled for last week. So their response was OK, I dont need them anymore - goodbye. The parts are under warranty so I send them the part I replaced myself and the invoice for the cost. I didnt get a response. So 3 months later I send a second letter. Three more months and still no response. I can remember when Maytag had commercials showing their repair sleeping because they had no work to do. Now, their products are failing and their entire service depart is asleep.

We paid for a brand new washer and dryer from Maytag/Whirlpool. Right on the machines it has stamped in a metal plate 10 year warranty. So at 4 years when my washer started screeching and smoking I called for service. Yes, there had been a leak that burned out something in the engine and the bearings were shot etc etc. But they have been back 3 times. Each time they lack some part. I first called them on July 29, 2020. Today is October 13, 2020. They have still not got the washer repaired. I need to do wash every day. We are a family. We also have a senior in her 80s. And dogs. I need to do wash every day. So for weeks I went to the laundromat. That cost a fortune. Then a couple of weeks ago I impulse bought a new washing machine. A Samsung. On sale. Doesnt match the Maytag dryer. And the old washing machine got moved out to the garage. Its the pandemic. I cant keep going to the laundromat. What good is a warranty if Maytag/Whirlpool always has excuses for why they dont have parts. Its the motor. The very basis of the machine. It took them 2 weeks just to look for one. You wouldnt believe the excuses they make when we talk. But I am really unhappy with the way it all worked out. What good is a repaired machine 3 months later than I needed it. I had to buy a new machine. Why didnt they just tell me to do that on day 1 so I could avoid the laundromat. Why are they spending so much money to basically repair everything in that washer when they could have just bought me the new machine. When is a warranty not a warranty at all, but just a big lie?

I love my new fridge! It has all the bells and whistles and looks/works great! My ice maker is the bomb! Best design Ive ever seen!

After my divorce, I bought a new house for my youngest son and me. It came without a fridge, so I used some of my settlement money to buy one I had been dying to get - stainless, French door, with bottom drawer freezer! It worked fine for the first 9 months or so. Then, water started pouring through the ceiling of my downstairs master bedroom. Turns out it was coming from the freezer water line. Ceiling tiles ruined, carpet stained. Then it started making this god awful noise. It starts, rumbles for a while (long enough to wake everyone up or give the dog a coronary), then is quiet for a while. Next, I open the freezer to find a sheet of ice across the bottom of the drawer. I assumed I had done something, so I got rid of it and thought nothing else of it. Last night, I get ready to make dinner and there is this blizzard of frost all over the freezer. It looks like a winter wonderland. I am afraid to see what is there when I go home and even more fearful to attempt to use my warranty.

We have the 4000 series front loader washer. Within 8 months of owning it, it would shut off in mid cycle. You have to unplug it to restart it. Then, when it completes the cycle, it is still soaking wet. So, you have to put it through the drain and spin cycle again. There is something major wrong with the spin cycle. It takes about 2 hours to do one load of laundry and you have to stay home to do all of the steps. It costs as much to fix it as the machine costs. It’s the worst washer we have ever had. No more Maytags!

I wish we would have never bought this brand and model. Within a month there was a loud banging and the serviceman came out and changed a valve out but it just got a little quieter but never went away. 2nd issue is cloths ball up when your doing bedding. Not sure if they are really clean or not. 3rd when we take the cloths out of the washer we are still seeing soap spots where they were not rinsed very well. We are using the right soap Gain but we cannot wash cloths in the bedding setting. We have to use the extra rinse setting to get all the soap out which defeats the whole savings issue of this machine. It says when you do your monthly machine cleaning it resets the water level but there never seems to be enough water in the tub. Also if your doing sheets in the washer and when the spin cycle starts you have to hold your breath to see if its going to get out of balance which it does 50% of the time so you stop and move things around. Also we cannot put a whole lot of cloths into this big drum because they dont wash correctly. Worst purchase we ever made. With all the negative reviews you would think that Maytag would come out with some fixes but I dont think they really care anymore.

I bought a Maytag Gemini double oven gas range 5 burners (model MGT8885XS000), even air true convection cooking. Within 4 months, 1 of the gas valves (knobs to turn gas on with) froze. I could not turn one of the top burners off. Maytag came out and fixed it. Three months later, another one froze. Again Maytag came out and fixed it. Our warranty ended. Over the next year, all five burner valves have frozen. I called Maytag, told them what happened. The most they could do for me was to give me the part half off. So I can pay $200.00 for parts and pay for a repairman to come out and fix it. The oven cost $2,000.00. I am still paying for it. Chances are if I repaired it would break again.

We have a bottom freezer Maytag refrigerator and after 2 years normal use it started leaking water onto the floor every day. After researching this problem I see that it is a widespread issue originating from an engineering mistake. I spent a weekend afternoon taking apart the freezer, clearing the frozen drain line, and putting it all back together. Im assuming this will keep happening every so often since it is a Design Flaw! Do yourself a favor and avoid Maytag!

Ive always loved Maytag but this centennial makes grinding noise and doesnt wash clothes well. Even on largest setting the drum never fills all the way up with water. It adds water 8 times during wash cycle only to immediately go to drain after last add. Ive only had for approx 4 years and the 10yr warranty only covers motor and basket so be sure to understand your warranties.

This is about my model MFI2569VEB2 refrigerator. It has French doors with bottom pull-out freezer, refrigerator door ice and filtered water dispenser. The delivery person installed the fridge and took off outside plastic and left inside plastic in. It froze everything until I took out the inside plastic. Within the first year, water started shooting out of the top of the fridge. A rubber connector for the icemaker, which was on top of the fridge, had broken. Within 18 months, it freezes everything in the refrigerator, even on the warmest setting. I have to leave it unplugged each night. The icemaker gets big chunks of ice stuck to it and wont let ice out. On top of all of that, the water from the fridge door pours out extremely slowly, this just how they are built.I will have to fix the thing myself and eat the expenses, so to speak. I bought the Maytag because Samsung had poor reviews. No matter how fancy you want your refrigerator to be, and how nice you want it to look in your kitchen, stick to the basics. The fewer bells and whistles, the more reliable.

Freezer does not freeze well. Causes most our food to get freezer burned. We tried turning it up and down but made no difference. Actually went and bought a separate freezer for meats.

Maytag wont fix new washer. Service person came 3X, but it still wont go to rinse cycle. Last 2X Maytag said service scheduled, but no one showed. MT mgr said cant help & to just keep calling back.

I bought a Maytag microwave model mmv4203ds00 on May 2010. On 8-20-10, the microwave stopped working. It was serviced under warranty. However, on 10-31-11, the microwave stopped working again.

The refrigerator is not keeping cold. The freezer is full of frost/ice. I had this fridge looked at twice in the past. Its about 6-7 years old.In the past, Maytag was considered a high end product. I wonder where the manufacturing is taking place for most of the parts. Could be it was cheaper to go overseas and now we are all paying for unacceptable products.I will never purchase Maytag. Maytag should be selling products they can stand behind! Products that are made in the USA, where our standards are higher and we expect products that work!

I purchased a Maytag electric dryer Bravo 300 Series in November 2009. December 2011, the main computer board went out and had to be replaced. Do not purchase Maytag appliances. They do not stand by their defective products. First and last Maytag purchase.

This machine doesnt wash your clothes. It leaves them dry & the agitator sucks too. I am so annoyed. I just bought them & had them delivered 7/27/15. It has only been a few days & NOT satisfied. Overpriced over $800 for it & its crap! Same with the Bravo dryer, it takes forever to dry. I wish I still had my old washer & dryer (had them for 7 years, NO problems). Very unsatisfied. DONT buy these, they are total CRAP!

I purchased a Maytag microwave oven on July 22, 2011. It was delivered August 2. Model no. MMV4203DW, serial no. CK01001086. I paid $279 at Lowes Spokane Valley WA. I made a family brand name dinner for six in the original black carton, put the rack into the microwave, followed all the directions as the microwave was new. The carton melted inside and burned a place where the rack had rested. This melted before the time was up. I had followed all the directions. This was the first incident that was a problem. Next incident was a large bag of popcorn (microwave has two settings for popcorn--large or small). This burned the bag black before the allowed automatic setting. Third incident was another bag of popcorn, which resulted to a fire. I tried putting it out with a large lid, which now has permanent black smoke stains. The fire was so hot I could not remove the popcorn bag. I had to use two pancake spatulas to throw it outside where it continued to have flames and burned itself out. The next fire was with a baked potato. This was set for a regular potato setting. This fire was great flames. I tried putting this out with salt and a pan lid. I also removed it with a large metal strainer, an Asian type which is large, and used another spatula to scoop the flaming potato and took it outside while it continued to burn. This time the microwave burned itself out. All lights would not function so I unplugged it from the outlet. I have repeatedly told Ava that I had previously owned a Kenmore convection microwave and the only time I used the rack was when I baked something. She continued to ignore this and said that I used the rack to make popcorn, baked potato, etc.

Bought a brand new Maytag French Door Bottom Mount refrigerator in 2014 to simply upgrade to stainless steel. Put my old refrigerator that I have had for 17 years in the garage. Never EVER had an issue with it and it still runs perfectly. Well, just out of warranty in May of 2015, the ice maker stopped working in the new Maytag. Called and got service. Learned there was a recalled part. Service man fixed. 2 days later, it broke again. They came back out and fixed again. This time, the motor was REALLY LOUD. They came out to replace that. Now, both the freezer and refrigerator are not properly cooling. Cannot keep ice cream and cannot make ice. Called again. I was told these dual fan systems simply do not work. I am out of warranty and too bad for me. A wasted $2500!!!

At 14 months old Main computer box failed, caused the machine to shut down on unbalanced load ($400). At 28 months old Main computer box failed, caused the machine to shut down on unbalanced load. In addition when the service guy was underneath the machine to change the module he noticed the stator housing to the motor was falling off. He said he never saw anything like it. After reading about all the problems people have with these machines I have talked friends and relatives out of making the same mistake of buying an old and trusted brand like Maytag. .

I am angry at my Maytag! It sprays water on clothes that is not enough to soak them or let the detergent to be dissolved especially for towels. Hopelessly, I Hand Wash my towels, rinse in tub then just put them in the machine to spin. BAD BAD :( :( Is it possible to increase the water amount?

I purchased a new gas range in Nov 2013, but didnt use it until April because I was remodeling a house I had just bought. When I used it to cook Easter dinner, my meal was cold; the oven heats, then shuts off. Maytag has sent service techs 3 times. They have replaced the control board and the DSI module and ordered another part, for which we have been waiting over 3 weeks. Now they tell me it will be here next week. Maytag obviously cannot fix the NEW range, but they refuse to replace it. They deem it to be repairable though they cannot repair it. Customer service claims to be sympathetic, but will do nothing except schedule another service call and offer to extend my service warranty. What good is a service warranty if they cant repair the appliance? If youre smart, youll steer clear of Maytag and Whirlpool appliances. They are total CRAP.

After reading all the reviews I realize this is a wide spread complaint. After 2 1/2 years the control panel on my Maytag Dishwasher will not work. You press the keys and hope for the best. I am thinking of going to the media with my complaint. Maybe we will all get some sort of refund or upgrade.

After 18 months of use Our Maytag Dishwasher (MDB7749) has the same control panel problem as a lot of other user complaints. I wish I too had read the consumer reviews before my purchase. We will never buy another Whirlpool product!!

I bought a Maytag Bravo washer and dryer 18 months ago. While taking clothes out of my washer, I noticed that the plastic collar above the washtub was shredding around the edges. I called the manufacturer about it. Because it was more than 12 months old, they refused to do anything about it. I feel that shouldnt happen so soon after purchase. Im a single person and dont do that much laundry. The piece should be made of something more durable. I will never buy another Maytag product. Is there anything further I can do to pursue this?

Maytag Top-loading washer MVWP475EWO - I just want to comment on how engineers have made our washing machines worse instead of better. I had to replace my Whirlpool Cabrio washing machine - and did try a new one of that brand, but had the dealer take it back. It had so little water when it ran and was a piece of junk. Anyway, replaced it with the Maytag and it too has the water saving feature (which I understand all of them do) but I have to put it on the bulky setting all the time to even get the water to at least cover the clothes. The clothes just barely, if at all, actually move! They sort of rotate a little at a very slow speed. Boy, maybe this was the time to try a front loader so the clothes at least moved a little in the machine! I am so disappointed in how all the machines are manufactured now. One dealer told me I would like the Speed Queen, but it would take five weeks to get one. Thought this Maytag might do the trick, but now Im stuck with it anyway. It does not spin the clothes out nearly so well as my old Cabrio did. The clothes are pretty wet! So, another fine engineering feature. I wish the engineers would be the ones that actually did some laundry so they would see how bad the machines are. My daughter has three young boys and theres no way this would clean the clothes for her. I told her she should be glad her machine is still working. The dealer was very nice about it when I returned the other one, but it seems all the machines arent really made to clean clothes anymore.

Maytag Bravo model MVWB750WQO. Bought this washer in 2009 for 1300 thinking it would last at least 10 years! Wrong! I loved it until a few months ago when it started making VERY LOUD noises during final spins. Sounded like the house was going to take off. Then today it started leaking water. Repairman said it needed a drum, seal and gasket. Would have cost 700-800 to fix. Needless to say we bought a new washer today, and it wasnt a Maytag!! For that much money I was expecting the washer to last a long time!

The dishwasher is only one and a half years old and like many others are having trouble with the control panel. The model is MDB89495AWO which cost nearly $800. The dishwasher does not shutdown after an operating cycle. On contacting Maytag with the symptoms they advised that they have never heard of a similar problem. On reading the comments/experience of other Maytag owners I am undecided whether to scrap this unit and buy another make!

I have the Maytag Direct Drive Motor washing & dryer set the is supposed to be “commercial technology.” The washer is supposed to keep wet clothes fresh if they don’t make it to the dryer right away. After 2 years, I disagree in that it offers no better outcome than the much older machine I replaced. Furthermore the dryer cuts off leaving my clothes damp every single time, which I cannot stand. It leaves my clothes to wrinkle terribly and damp to stink if I do not collect them fast. I honestly wish I still had my old set. All the new features simply fail to measure up not to mention over complicate and add expense to repairs.

I have had it (Model MDB6000AWB) for a few years now. It had to have the door replaced per recall. This dishwasher does not wash dishes well at all; need to rewash many items after going through normal wash cycle. Also, all spokes are burning and falling off, along with pans getting burn marks. I am not sure how safe this is anymore. I am going to purchase another dishwasher, but not a Maytag!

Bravos 4.3 High Efficiency Washer - The worst washer ever. I recently returned from burying my step-mother. She actually used the same washer and dryer, by Maytag, for over 50 years. Those days are gone forever. This is my second set of Maytags in ten years. The first literally stopped working just after the first year warranty ran out. I still have them inside my pantry, like a set of anchors. Notwithstanding that, I thought, Maytag was a good brand, it must have just been the style of machines, so I purchased these in January. After over six months of usage, I am amazed at how many times I have to wash a single load of clothing to get the items clean. Who cares if the machine saves water? What was wrong with having an agitator? I literally have to remove freshly laundered clothing, turn it over and run the wash again to get the top of the laundry clean. I have had a blanket finish for the fourth time to get it clean, only to have to hang it outside because it is so full of water, the weight keeps it from spinning properly. And why would you remove a timer feature which permits very busy, working people, to wash their items while they are on the way home or in the middle of the night so that there is no waiting to pop the clothes in the dryer? None of the cycles takes less than 80 minutes to complete. Who has 80 minutes to wait on the washer to do its job? I am so upset about the amount of money I spent on all of these machines. Just think, I could have brought the over 50 years old set home from my step-mothers and had a washer and dryer do what they were supposed to do -- clean the clothes.

We bought our Maytag dishwasher less than 2 years ago (model MDB8969SDM0) and we are remodeling our kitchen now January 2018, and when we pulled the dishwasher out we found that the wire (12/2) had melted into the back panel. We won’t be putting this Maytag back in.