Stay away from Maytag Bravo washer. We bought one a year ago and fought with them this whole year. It leaves lots lint on clothes. Weve had 2 technicians here 4 times. Now they finally said we can replace but will only get a prorated credit even though its been junk since day one and we contacted them immediately. If we wouldve known they wouldnt stand by their warranty we wouldve hauled it back to store for full refund. They dragged us along a year and now warranty is no good but they will prorate. Not fair at all.

I bought my Maytag Bravos washer and dryer set about 3.5 years ago when I moved into my home. There was a 20-year old set here that did work, but I wanted something newer and more efficient, so I donated the old set and bought these. Performance of the washer has always seemed mediocre, clothes dont get as clean as I think they should, whites are dingy, despite using hard-water additives and the correct HE products.A few months ago, the washer started a new behavior: stopping during the initial fill cycle and displaying an F1 error. I soon figured out if I hit cancel then start again, it would resume filling and proceed with the cycle. Over time, I had to repeat it more and more. Its now up to ten F1 errors both at the beginning and end of the cycle. I dont have that kind of time to babysit my washer. I already have a full-time job.I have called Maytag/Whirlpool twice now, both times getting unsatisfactory answers. Even after escalating to the customer service supervisor, I was basically told that it is most likely the control board that is the problem and since Im no longer under warranty (that washer ‘is’ almost 4 years old, maam), Id either have to order the part myself from their supplier (total cost $250 + the risk of DIY), or buy their service package for about $350 which included fixing that problem plus one additional years warranty.I pointed out that for a major household appliance that I (over) paid for, I expect a life of more than 4 years, especially since I had a working 20-year old washer when I moved in here. Since when is this acceptable? I could understand if it were a wear-and-tear part, like a rubber seal or something that moved constantly and would eventually need replaced. But this is the electronics module, something that cant (or at least, shouldnt) be worn down or broken by use or even user error. This is an integral part of the machine, and if it has a fault (which it clearly does), the manufacturer needs to stand behind it and help the consumer.What angered me even further is that the customer service manager even admitted that models similar to mine had had similar problems, and a free control board was sent to those customers. But my model was not in that range of production, so clearly they have no fault, in their eyes. Apparently, its not even remotely possible that maybe when they determined the range of models they believed to be faulty, mine hadnt been in use long enough to display the same behavior? Maybe the range they selected is too restrictive and they missed some. From the volume of complaints Ive seen online, Id bet that to be the case.I asked to be transferred to their legal department, and was refused because we just dont transfer customers to the legal department. Well, I just dont buy Maytag or Whirlpool anymore, and Im going to do my best to make sure nobody else does either. Im replacing this ** with a different brand, one Ill be sure has tremendous reviews and a manufacturer that will stand behind it.

I also purchased a Maytag dishwasher a few years ago. It has never worked that well. We had a repairman come out once to replace the control board but the problem soon returned. Interestingly, we found that if we wait long enough until the control panel is in the mood, the dishwasher works again and the control panel responds to button pushes, until the problem returns.I dont recall what model I purchased but it seems to be irrelevant. From reading the other customer complaints, its quite obvious that all Maytag dishwashers inherently have problems with their control panels and Maytag intends on doing nothing about it. I guess the extra repair costs that their customers have to pay for their defective products brings in some additional revenue to Maytag, so theres no real motivation for them to fix their ** products.

We purchased a new Maytag side-by-side refrigerator back in 2011 and for the last several months it has been leaking water into the bottom of the freezer unit when it goes through the automatic defrost process. The water freezes and after a few of these cycles causing the ice to accumulate and build up, it starts to leak out onto our kitchen floor. About every 10 days we have to open the freezer door, break up the accumulated ice on the bottom of the freezer and remove the ice chunks by hand. What a pain in the neck! Most of the time we can prevent the water from escaping, but not always. This is going to damage our kitchen floor, not to mention its a safety hazard for slip and falls, and/or fire or shock hazards. We have contacted Maytag directly, but nothing will be done as they say its beyond the 12 month standard warranty. They said one option is for us to purchase an extended warranty plan from them for only $359. Really? Are you kidding me?? They dont seem to care about a potential product liability property damage claim/suit, nor an exposure for a potential bodily injury claim. As Ive tried to explain, this is NOT a warranty situation, its a product defect situation and one probably worth a class action lawsuit based on the number of complaints Im aware of. They know its a product defect problem, but choose to ignore it at the expense of numerous innocent consumers. The only resolution seems to be filing your own lawsuit against them for some kind of remedy to this very aggravating situation that occurs every 10 days or so. Maytag used to be very good appliances, ones that were made of high quality materials, and lasted for years without any problems. Thats why I became a Maytag fan in the first place, but ever since they were purchased by Whirlpool Corporation, its not the same old Maytag we used to know and love. DO NOT BUY MAYTAG APPLIANCES - you will regret it!!

I remodeled my kitchen, put in all new Maytag Almond appliances washer, dryer, stove, refrigerator, dishwasher and microwave oven. I was pleased with everything but the stove. The stove was $800.00. The oven caught fire three times and smoked up my house. I replaced the stove with another brand, cheaper and safer. I moved to a new house, five years later, bought all Maytag appliances stainless steel. The hinge on the deli tray broke, the inside is thin plastic, not covered in extended warranty. The stove caught fire (I didnt learn the first time around)! The microwave has a thin, bendable, plastic rack, the handle snapped right off. I cant buy a handle separate from the door. Now the microwave wont heat! My dishwasher was recalled. The heating element could have caused a fire! Nothing that breaks or malfunctions is covered by warranty. Who needs to pay for a warranty too and get no parts or service rendered! I will buy all new appliances and when I do, it wont be anything Maytag makes and none of their other brands! This stuff is very expensive garbage! Somebody please initiate a class action suit!

Maytag model #MDB6949SC, purchased Feb 22, 2015. In early May plastic parts from the top rack wheel assembly broke. Assembly unit replaced at no cost through the 1 year warranty. (cost = time and effort to arrange replacement with repair person). Same parts broke again in November - replaced at no cost again under warranty. Warranty expires in two months. If past performance indicates future performance, this part will need replacing twice a year at ~$140 per visit or $280 per year. Not a good thing. Called Whirlpool and with several calls and emails. They offered an extension of a year on the warranty. I think using plastic for this wheel assembly unit is a design flaw. Would not recommend this dishwasher.

I purchased this relatively expensive range and could not have imagined how dissatisfied I would be. The Aqualift cleaning technology does not work. There is no way to clean the oven door. They stress not to use oven cleaner, but as the Aqualift system does nothing to clean the oven door, there is no choice but to use oven cleaner, which they say will ruin the oven coating. Also, the grates are very heavy and it is impractical to clean the range top. I wish I had researched further; this product is a MAJOR disappointment.

From day one I didnt like how this machine restricted how I can wash my clothing. There is no water volume controller. It is all automatic, which sounded fine in the store, but once I used it I quickly realized it is horrible. I can not add extra laundry or detergent in at the last minute because it says not to open the lid at all once you start the load. The settings are very glitchy. They do not seem consistent. There is a knob for level of soil on the clothing which doesnt seem to do anything at all. Ive had it now for four years and it has only gotten worse. Now I can only use one setting Hand Wash. Try doing a teenage boys clothes in Hand Wash and youll find out quickly that nothing gets clean that way. Oh, and all of the sudden the spin cycles are not working, they spin when they want to but they rarely get rid of the dirty water. Spinning in dirty water does not get clothes clean either. This machine is horrible, hands down, the worst washing machine I have ever owned.

The washer worked great for the first 6 months, then it didnt dissolve the soap, it wouldnt complete the cycle, and there is a loose bolt like sound when you spin the drum. The load level is not an issue. We have had the serviceman out four times, he has called the tech support each time and they cannot resolve the issue. Maytag said sorry! Unless it does it constantly then they cant help. The control panel has been replaced and the drum has been replaced. So we keep paying the water and sewer bill to rerun the load 1/2/3 times to get it to complete the cycle. This washer was purchased last May, 2011 and they say were stuck with it.

I purchase a Maytag dishwasher from Home Depot on 12/31/11. Based on the their commercials, I thought they were dependable. I did purchase an extended warranty, as I always do with any new appliance. After 2 years, the dishwasher stop working. I contact Home Depot and the extended warranty and was told to contact the manufacturer. Maytag blamed the extended warranty for the problem. They told me they could not help me. And could not help me. I will never ever buy any appliances from Maytag again. This model is M936/110V cord.

I have a Maytag Centennial washing machine which is about 3 years old. In the past 6 months I have to replace the actuator twice. I have had Maytag washers for about 40 years. I will never purchase another one unless it is the old style. That would mean that it would be a used one. This machine is a bad purchase. Maytag use to stand for quality, but not anymore.

The washer is so loud it can be heard all over my home (my home is 2700 sq.). It sounds like metal to metal grinding. I was told thats how the run and the first bit of water isnt enough to even wet the clothes. Id never buy another one (even though this is my 3rd Maytag washer. Im 78 yrs.old).

Weve had this washer for five months now and really regret buying it. It cannot remove even minor stains and often leaves residue on clothes, even with extra rinsing. I spilled coffee on some fleece pajamas and it took four washings to get the smell out.

THIS PRODUCT IS CRAP!!!! I spend $699.00 at Home Depot, after 1/12 years the console stopped working. Maytags engineering staff should be fired!!! You stole my hard earned money. NOT once, but on a washing machine as well. I will never buy a Maytag product again. HEY NO WONDER THE REPAIR man sits on his ** the rest of the company does too! I dont have 250.00 dollars to fix this thing. Shame on your company. No wonder you dont want anything. DONT BUY MAYTAG, buyer beware. I am angry but this is not **!

I purchased a Maytag MDB7749AWM model dishwasher in March of 2012 for approximately $600. Fifteen months later, the control panel has gone out on it. From what I understand, this problem happens so often that its not even worth repairing this dishwasher.

I am grateful I dont have to beat my clothes on a rock. Absolutely the worst dryer Ive ever had!!! Previous Kenmore washer was my favorite! This Maytag does not allow me options to stop, soak & freely open & close as I choose. Even my adult children who occasionally use it say its the worst!

We bought a Maytag Bravo washer and after less than 6 months of use, it stopped working with an F51 or 53 error (cant remember which because its been a month now). After looking online, it seems that almost everyone who buys this gets this error and has to have a part replaced! And Whirlpool hasnt recalled the faulty part even though everything Ive read says it should be a recall.Its now taken over a month to get a repair person in to fix it. From the time we called Maytag, to the referral to the service person, to the service appointment, to waiting over 2 weeks for the part to come in, its been over a month with no washer. This is unacceptable Maytag! The repair company is finally showing up tomorrow only after 3 left messages from us.Either build a better washer or stock your replacement parts with the local repair companies and you should be reimbursing your customers whove spent a lot of money at the laundromat after spending between $700 and $900 on your washing machines.

We bought a refrigerator June 4th 2014. 6 month ago the freezer and refrigerator was getting warm. Had to call repair service, it was the blower! On Saturday 12/9/17 freezer wasnt freezing, then fridge was clicking on and off. Unplugged it, called repair service, it was the compressor. $800.00 to fix it, the same amount as when we purchased it. Repair service told us to call Maytag, he said, Maybe they will help you, would not help at all. Talked to Lori, all she said was warranty is up after a year, I then said, I think a refrigerator should last longer than 3 years! Will never buy anything Maytag again! Yes Maytag does SUCK!!!

Sometimes the control panel is difficult to work with especially if the wash is paused to add more clothes or detergent. The good things is that the tub is very large so a comforter can be washed and you can control the amount of water depending on the amount of what is being washed. I also like that it doesnt have the big agitator in the middle.

I had my Maytag washer and dryer just barely over 30 days. My washer sounded awful and I had to get a new motor. Then my clothes would come out with dry spots. Not enough water. The computer was replaced and within a few months of purchase, all the major parts of my washer were replaced. I hate it! My clothes still come out with dry spots and it is loud. Worst major purchase I made. Dryer so far has been ok.

I have enjoyed my microwave and it has lasted 10 years so far. The only problem I have had is the handle coming off but I clip it back on. Also I changed the bulb. The microwave is over the stove and matched the rest of my appliances. Basically, I would recommend Maytag for any appliances that a person would need to buy.

Maytag range model mer8875ws - Glass top broke on brand new oven over most used burner then glass spider lined out from there. Wife called Maytag and they told her that it broke from the impact of something dropping on it. I guess the man was psychic because he had no picture of SO CALLED IMPACT SITE. Now they wont replace or fix range, ** Maytag. Paid 699 for range they want to charge me 900 to fix. MMOOORROOONNSS! Like ** thats how big business treats everyone now. Thats how big business treats people these days.

A 14-month-old cabinet dryer required a new motor. I was promised delivery in 3/4 days. Following several calls, all of which resulted in the delivery date being extended to over eight weeks, the same engineer called to install the new motor. He refused to do it as the surrounding paneling had not been removed to give him access to the cabinet. It took another four days for him to return after we called in our builder to remove the panel--three screws and four-minute work. I asked for the warranty to be extended, by way of recognition of Maytags awful service. My request was rejected out of hand and the reasons do not accord with the chronological evidence I hold. I am about to bring a claim in the local County Court.

I bought this washer and dryer (Bravos MCT MA655LDY) after receiving several notices from Hydro that I was consuming more electricity than my neighbours! It was delivered March 31, 2018. On July 5th 2018 I tried to use the washer. It lasted exactly 3 months! I called The Brick who sent a technician out, he said the control had gone. Not sure what that is, but 3 months? This is absurd. I would like them to replace this washer.

We bought all new appliances for our remodel. I wish I could return this dishwasher. It has a problem with the door staying closed. I added images of how we are able to make it work. A service person is coming by tomorrow to put a new latch on it (I read several reviews saying the latch is messed up). So I made sure the service person is coming with the part. I called Home Depot when the problem started (used for up to 5 washes or so). And Home Depot wont return it! I called Maytag and they tried selling me an extended warranty and I asked what about the 10 year warranty the machine is supposed to come with? I guess thats a joke as the lady told me I should of read the fine print. So buyers beware! I wish I would of know about Maytag. I would have about a Samsung instead!!!

Food stored next to the ice dispenser freezes. Freezer floor builds up with 1 1/2 to 2 of ice every couple of weeks, door wont close and water leaks on floor.

Bought a new Maytag dishwasher in July 2013. In December it quit working and the problem was the control panel. The service tech knew automatically what the problem was when he arrived. It is now May 2014 and the control panel has gone out again. Contacted Maytag and was told they will extend the warranty another six months from the original warranty. After reading that this has been offered to others with mixed results I have my doubts on whether it will be honored. This is our last Maytag appliance.

I would not recommend the Maytag washer with the large tub. It does not clean your clothes. I called Maytag and they do not care as long as it uses as little water as possible! Not a good value for the money!! That was the first time and last time I buy a Maytag... Thats the last $5000 they will get from us!

I purchased a Maytag Front-Loading Washing machine. It was purchased on 11/30/15. Approximately this January, 2017 the spin cycle stopped getting all the water out of the laundry. Towels came out wet, shirts came out wet and I tried washing a small bathroom rug that came out of the washer dripping with water. My husband called Maytag to tell them about this issue. They told him I didnt know how to load the washer machine. Wow, I have only been using washing machines for 45 years and now I dont know how to load a machine. Then they said they will send him a video to watch on how to load a washing machine. I watched it. I wasnt doing anything incorrectly. (Maybe someone should send them a video on how to build a proper washing machine.) I previously had a Maytag Neptune machine that lasted twenty years until there was a class action suit against the machine. The clothes came out fine from that machine. I just purchased an Electrolux front loader that works beautifully. Now I have a Maytag machine that is nothing but a piece of junk in my opinion. It cost $824.21. I will never buy a Maytag machine EVER. MHW7100DW.

We are in the process of replacing the 2nd control board in the past 2 years (have has this dishwasher for 3 yrs) on our Maytag dishwasher model MD87749AWW1. The lights on the panel completely quit working mid cycle. At $175 per replacement, we are into repairs for half of what we paid for the dishwasher. Bought Maytag because it is made in the USA but found out that a majority of the parts are imported from China? Very disappointing.

We have a Maytag Neptune washer and dryer. The seal is full of mold. We replaced the seal a few years ago and I wipe it and try to clean it every load, but it is useless. I saw there was a class action suit and I was never notified of this. I would have participated. I want it fixed, replacing the seal does not work.

On May 23, 2009, I purchased a Maytag bottom mount refrigerator even though I knew that Maytag had many problems with this product and others. I innocently thought that by the year 2009, all their problems would have been taken care of - I was wrong. On April 2, 2011, the freezer part of the refrigerator was not defrosting. I had to make a service call to replace the control board. On March 3, 2013, the regular part of the refrigerator was not cooling. I had to make a service call to replace the control board.Complaining to Whirlpool is a waste of time. The best answer I have received is, I am sorry. There is no end to the garbage Whirlpool is manufacturing and by my experience they dont care. Why dont we, the consumers, hire a lawyer and start a class action suit to let Whirlpool know we are fed up with being ripped off?

I just bought a brand new Maytag microwave a few weeks ago. The door is already broken! I’ve been sitting here 4 hours! waiting for a repairman man. No call, no show! I am missing work and gym time because MAYTAG sold me a faulty microwave in the first place! Never again will I buy Maytag products!

I bought a brand new top/bottom refrigerator from them. 1 1/2 yrs later, the cooling stopped and had 2 repair guys come out. They replaced it with BRAND NEW refrigerator. Now 1 1/2 yrs later, the same issue is happening. ALL my food I buy goes to waste. I bought NEW so this wouldnt happen. What happened to the old fridges from back in the day! Maytag has the WORST Customer Service!!!

This machine sucks. Im down to washing three to four items only on an extra capacity machine because every single load becomes unbalanced. Feeling the weight of each item and then placing it correctly doesnt work. Repairman came out. Said it was balanced. Lie. At this point I want to take a sledgehammer to it and send the pieces one by one to Maytag. They should be embarrassed to even have this product for sale to the public with their name on it.

Washer has plenty of functions for me to was even my work clothes. These saves me money and time. Washer leaves clothes clean and you can even wash your blankets.

We purchased a Bravo HE washer about a year ago after our old Maytag finally died after 17 years. Our new one is more quiet, does a good job with less water although the cycle times are a bit longer.

My son gave me a Maytag washer for Christmas 2013. I hate it. Sometimes it takes me 5 tries to get my clothes washed, and then it dont go all the way through the cycle. I have to constantly check on it. I hate it. Can you give me some tips on what may be causing this... Very disappointed.

I purchased a Maytag Bravos 500 Series HE washer. 3/2013. The machine sensor started giving problems less than 2 years after purchase. The sensor is not working. The wash lights stays on, and the clothes are not cleaned. I have to manually turn the dial to put in on the rinse cycle and then turn the dial to the spin cycle. Its a piece of junk. I called Maytag twice and the only thing the representatives on the phone say: I will send a certified technician to see whats the problem. Price: $129.00 service call and additional costs for labor, parts, etc. Maytag had a very good reputation for its products. Will never buy anything Maytag or any products that fall under that brand.

I would say you have plenty of options when choosing a color for your dishwasher. You can choose black or stainless. Try one today you wont be disappointed. I load plenty of dishes into the space. It has extra pockets for little things and it has plenty of hooks and hangers to use for bigger cycles. Kenmore Dishwasher runs great. Very efficient and cleans the tough stains better than any dishwasher Ive ever used. I would recommend this to anyone looking to buy a dishwasher. Of all the dishwashers I researched at Lowes and Home Depot and Sears and Ace and other local stores, the Maytag was the lowest price with all the features I wanted.

The Maytag Bravo Washing Machine was sold as the top of the line. In reality it is very difficult to work with for three specific reasons. First, the spin speed is too high causing the clothes to be wound into tight balls causing pilling and the need to iron everything from t-shirts to workout pants. Second, the spin speed is so high that you can only put a few towels in the washer at a time or the machine goes off kilter several times a cycle. Finally, if you lower the spin speed the items take forever to dry. I used this for less than 30 days and tried to return it but Maytag would not take it back. The only cycle type I can use is the rapid wash unless I want to spend all day washing and drying one load. I hate this washer more than I can describe and will NEVER purchase another Maytag product. It absolutely ruins your clothes and Maytag takes no responsibility for making a very bad product.

I purchased the Neptune HE pair because they are front loading and can be set on pedestals to raise them to a comfortable working height, plus the brand and reputation are both excellent. I like that the chimes can be adjusted from low to high, or turned off. The front loading washers clean so much better and with a lot less damage to items than washers with center agitators. Looks are secondary, thats for sure. Functions like warm/warm cycles and being able to adjust to whatever load needs to be washed is really most important to me. Any appliances with a good, proven track record of reliability with few repairs is high on my list. Expensive appliances should be made to last and be of durable quality! No cheap plastic or weak-looking welds or components, thank you! Quiet operation and dependable cleaning and drying are top in my book, and this pair has exceeded even my picky expectations in total overall performance. They are 11 years old now and look & function like new! I had one minor repair on the washer at 5 years, and not a single problem since. With front loading washers, its important to keep the door open a little when not in use so that they dont get a musky smell. Ive gotten into the habit of using laundry boosters to help clothes, sheets, and towels smelling fresh longer, and putting a small amount in the washer drum has kept my whole laundry room smelling nice. Purchasing the pedestal drawers to set the washer and dryer on added extra storage to my laundry and its much easier for me to load/unload them at this comfortable height. Im totally spoiled by it now, so when I use someone elses laundry room (when I visit) I am reminded how nice my own setup is.

This is the WORST washing machine I have ever had. You cannot control how much water goes into the machine and the clothes being washed are not even covered by water. They stick out above the water at least a few inches!!! How can anything get clean if no water is touching it! I even add water into the machine at the beginning with jugs of water just to cover the clothes... the machine automatically gets rid of that extra water and when the wash cycle comes on again the clothes are not submerged! I paid A LOT of money for this awful machine and Maytag needs to do something about it! And, yes there is a sticky gummy substance on all the dark clothes! I even put clothes in the washer with a dirt spot on it purposely and the spot is always there when the wash is done. Nothing gets clean! DO NOT BUY this machine... you will be very sorry!!!

Hello, My recently purchased dishwasher has leaked water within less than half an hour of the fifth time to be used and showed error: F8E4, dishwasher model and SN are: Model: MDB4949SKZ. Serial # : FA3003347. Registered: 09/11/2021, Ive been calling Home Depot who in turn asked the installer to check the connection, and the latter advised and reported its a manufacturer issue. And calling Maytag for several times but no response or action. On-line service scheduling of Maytag is not working!!! And the live chat is not helping, as well. Now my dishwasher is not working since more than two weeks, knowing that it has been installed only a month ago.

Maytag never fails to please me. My dishwasher is so quiet I sometimes have to put my ear next to it to make sure it’s actually working. The inside is stainless steel (those are the quietest) and it has a child lock so my 2 yo grandson can push all the buttons he wants and he still can’t mess things up. I love the high temp and sanitize features and everything is always clean and dry when done. It seems like it takes a long time to run through all the cycles, though. That and no adjustable top rack are the only two things I miss with my previous dishwasher.

Maytag Bravos XL top load. I purchased 2014. Three years old drum bearings went out, just two people in home. Very expensive to repair. Three years later I hear bearing going out again, in mean time had a F51 pop up and that means major failure call for service. I called Speed Queen and ordered a machine with all metal parts delivered the next day, and it is Made in America. I had purchased Maytag because of name but I will never purchase another Maytag. My friend had the same experience same time frames.

We updated our kitchen appliances in 2013 and purchased all from Home Depot. Purchased Maytag Refrigerator, free standing range and microwave. What a big mistake!!! Not one of them are worth what we paid for them. I just noticed that I was getting a (chemical) smell from inside our 6 year old 3 door model MFI2670XEM5 refrigerator. Well being I know what refrigerant smells like I have a leak in the interior of unit. This is my final issue with Maytag and their so called great built appliances, I have had nothing but troubles since about 2 years after we purchased it.I guess what really surprises me is that unit is built by Whirlpool and has their name all over unit and I always had good luck in the past with the brand. This is one of several issues including rust on freezer door, broken plastic drawer frames to French door hinges broken, ice maker door issues. What a waste of my money that I spent on these and now after 6 years need to buy all new. IT WILL NOT BE Maytag or Whirlpool!!!

I purchased Maytag fridge a year ago and it has been a nightmare. The freezer doesnt freeze items. the drawers were all damaged upon receiving. I have contacted Maytag for more than 10 times and 5 techs came that I paid 125 each visit to fix the fridge because I didnt purchase the warranty thinking it was a good product . It is not! They dont stand behind their word. They lie and they send unqualified techs the misdiagnose issue to collect service calls. Please avoid this brand by all cost. My experience is terrible and I never want to wish it on anyone.

I could not get parts for Maytag Model MHWE200XW00 Type 832A as the Whirlpool does not provide after sales service. I purchased the new washer in 2010 and lasted for just 4 years. I believe they guarantee supply of spare parts (Inner Basket, Outer Tub and Rubber Boot) for 10 years and more.

MAYTAG REFRIGERATOR SAFETY ISSUE SHARP EDGE Maytag refrigerator model MRT118FFZ01 purchased Feb.2018. There is a safety issue, sharp edges. Maytag has been aware of this for over 1yr from customer reviews. I went to consumer affairs.com and there are numerous complaints on products/customer service. I have been asking for a replacement door since Feb. On Sept. 7th I cut the palm of my hand on sharp edge, drew blood, no stitches but I was very upset. Called Maytag, transferred to the safety dept. sent out service tech. He reported that it was a safety issue, very sharp edge, he had to put duct tape on corner to prevent any more injuries! He requested that new doors(freezer&refrigerator door) only be sent, I do not want/need the whole unit replaced. Freezer door has sharp edge also. I have numerous emails to/from corporate office begging since Feb. for a new doors so that this would not happen! Maytags solution is to buy back refrigerator or I should pick another model. Neither is a solution for me. I picked this model for a reason. I asked them to provide me with the simplest solution which is to contact factory where it is made, red flag it, talk to manager, quality control check to see that there are no sharp edges before it is shipped to me. They refuse to do that 1 simple common courtesy, customer service request! They cannot guarantee that door will come without a sharp edge! My model is not the only 1 with this problem. I talked to salesman & model in store has sharp edge & in the reviews the same model had sharp edge which was submitted over 1yr ago! So Maytag has been aware of this safety issue for some time now but chooses to do nothing about it! I chose Whirlpool because of the name, I thought it stood for quality & above all excellent customer service. Was I wrong, found that out thru numerous phone/email conversations. They just dont care! Is it too much to ask Maytag to give me a refrigerator with no safety issues?!!! I have talked to Aaron in the corporate office, he was no help at all. His # 866-817-5404 ext **. I have all the emails to/from him. Please help, I want this same refrigerator, only model that would work for me. Now that I have had personal injury & have spent so much time/effort, aggravation since Feb. trying to have them do the right thing I feel that I am due monetary compensation. Bottom line this complaint is concerning a safety issue & horrible customer service from the call center to corporate offices! The Maytag name isnt what it used to be known for, quality & service.

Maytag Oven MGR8670WS1 - Purchased in the Fall of 2011 (along with a fridge... also faulty the freezer stopped working within a year). Ive had the oven stop working twice (in 2012). This week (spring 2014) would be the third time. It seems to be a faulty ignitor already replaced having to be replaced yet again. I have never used such faulty appliances EVER and never AGAIN. This is absolutely ridiculous.

Purchased a Maytag washer for my family of 8 because we do a lot of laundry and our Samsung washer failed after 3 years. I thought Maytag was a more reliable brand and was hopeful. The machine stopped working after less than 4 months of service. Manufacturers warranty repair came out and said it needed three new parts, motor, clutch and chip - said it would be another 2-3 weeks depending on parts. So all total without a washer for 4 weeks minimum - call the customer service people (first one was rude and short), 2nd one after 45 minutes on hold - told me the were no other options other than wait for the repair. Four months after a brand new washer and it failed. I requested a replacement option and they said no way. Their hotline talks about a positive customer experience and that seems to be a joke. Not helpful, super frustrated and they do not seem to care about the customer experience at all - terrible product and service

In order for the machine not to break you have to disassemble the drum agitator during normal use... Very poor design. Mine lasted just over two years. My initial cost was $570... Dont waste your money.

Maytag Free Standing 30-inch Gas Range - In 2004 we bought our model MGR5775QDS gas range with 5-burners because it offered the most BTU variety for the price: 1 burner with a high BTU (16K), 1 with low (5K), plus 2 in mid-range (9.5K) and 1 with 12K. Within half a year of using the oven, we turned on the self-cleaning function. Big mistake. One cleaning cycle later, our oven refused to ignite. The cleaning cycle burned out the ignition unit. Cant remember if its replacement then was under warranty but the repairman said this was a COMMON PROBLEM with Maytag and we best not use it EVER. In 2014 our cleaning lady mistakenly thinking she was doing us a favor, set the self-cleaning function. Once again, the ignition unit was destroyed. This time its replacement was $350 with part and labor. One and half months later, the oven is again non-functioning. This time our repair guy said the part is a very minor, inexpensive one BUT MAYTAG IS NO LONGER MAKING IT!!! The only way well get our oven back is if he can find another model and cannibalize it to fix ours. Are we disgruntled? Yes. Would we like to see a class action suit against Maytag for knowingly manufacturing a gas range with a malfunctioning self-cleaning unit that destroys oven parts? Yes. Will we ever again buy Maytag? Not on your life. A once stellar manufacturer gone down the tubes with a growing reputation for making junk. American-made appliances mean zip these days. Thank you for nothing, Maytag.

We have had our Maytag dishwasher MDB9100AWQ only 5 years and now it keeps shutting off. I see there is plenty of this complaint. I will not purchase another Maytag product after reading all these reviews and experiencing it.

Like many others, my Maytag Bravo motherboard has stopped working after about 2 years. The clothes do not get particularly clean, it is extremely noisy, and the wash cycles are excessively long. I would not recommend this appliance to anyone.

Maytag Jetclean EQ Plus Dishwasher - We purchased the dishwasher in June of 2014. Recently the control panel decided it wont work. There is power to the unit. I am told that the unit is no longer in warranty so we have to pay for everything.

I bought a Maytag Bravos top loader washer and dryer less than 2 years ago. I started having problems with my dryer 3 months ago and after several service calls (and a few hundred dollars), it still does not dry our clothes. I spent over $1500 for the pair and was excited to have a top end washer and dryer. My biggest complaint is with the manufacturer, Maytag - they just dont seem to care. I did not buy the extended warranty for two reasons. First, I bought a nice unit and expect it to work properly for a reasonable amount of time (at least 4-5 years without any problems). Second, they are just a bad purchase and they cost about half of the unit and if you buy a nice unit, you shouldnt need one. I could have bought a new dryer for what I spent to try and have this one work properly. My wife and I spent $600 for our last set which lasted 7 years without a problem; they were manufactured by GE, which I now wish I would have bought another GE. My wife talked me into buying a new pair to accommodate the needs of our growing family. I wished I would have kept the GE pair that was working.I would not recommend any Maytag appliance: they really just dont care to provide any reasonable service to stand behind their products. What a shame. This reminds me of why many foreign manufacturers are beating us at what we used to do best - make products that last and work! The washer and dryer look nice and have many great features, but these dont matter much if they dont work.

Same issue as everyone else. Bought the French door with middle deli drawer fridge November 2012 at Home Depot. After 2 1/2 years freezer drain froze up leaking water into the floor. Spent 6 hours fixing it. Now still less than 3 years old the ice maker is not working. Not a jam or water supply issue. Just dead. Looking into replacing the ice maker. Such a disappointment. Only thing this fridge is good for is its looks. Obviously common repeated defects. Wake up Maytag and accept some responsibility.

I purchased this high-end dishwasher 7 years ago and 3 years of fairly light use, the control panel on the top would operate sporadically or not at all. Called the dealer who sent out the repairman that installed it and had to replace the control panel to the tune of $300 once the labor was included (took 2 visits as he had to order the part, so 2 trip charges). Now 3 & 1/2 years later, it is doing it again!! A call to Maytag and then a transfer to Whirlpool customer service got me nowhere. They said there were no recalls or documentation for problems with the dishwasher. Really??? I see lots of complaints on this problem with very similar Maytag dishwasher models. They would not send me a new part at no charge as a result but offered to set up a service appointment for me so I can spend another $300 (probably higher now after 3 years) and would register my complaint. Thanks for nothing!Doing that would turn my originally $900 dishwasher into a $1500 one with the result that it will probably fail again in 3 years. Absolutely ridiculous customer service. I saw a YouTube video on taking it apart and applying silicone around the ribbon connections as others have done in the hopes I can get it working again for a while as I dont have the $$$ needed to replace it again on a retired fixed income. :(

Wish I had read the reviews! I have had Maytag before and they were awesome. New purchase is horrible! Doesnt clean the clothes, leaves a residue on clothing and dryer does not dry properly. Called Maytag and they said use Affresh. Spent $10 on a pack of 5, and it did no good. My dark clothing is getting ruined! The washer is also incredibly LOUD! Very disappointed in this company and would never recommend them to anyone! I had purchased at Lowes, but had a delayed delivery, so I cant take them back, or I would.

Not yet two years old, my Maytag Bravos dryer stopped working. When I called a technician to see what the problem was, he told me that the circuit board was burned out and it would be $500.00 to replace. I then called Maytag to find out if there was a problem with this machine and was told no. This apparently is a lie as there were numerous complaints when I checked the internet. I have five Maytag appliances and at this point, only one has not caused a problem. Maytag is not the company of the past when if you had a Maytag, you had the best. The repairman no longer sits around with nothing to do.

I bought the matching Bravos washer and dryer 4 years ago. I always bought Kenmore appliances but decided, based on the then reviews, that I would upgrade to Maytag. Biggest mistake I have made! I am a very tolerant person always looking for the best in anything. But I have to say, I hate both the washer and dryer. My clothes are faded, they shrink in the dryer even on delicate. I really cant say anything good about them. Today I washed 2 twin sheets, one king top sheet, and one very thin blanket. When I opened the washer, one twin sheet was on top and not even wet. So now I get to run another load and have to wait to remake my bed. When I have washed rugs on bulky, they are filled with soap when finished. Half the time, it doesnt spin out the water and I run a second and third spin cycle on a variety of items. I avoid doing laundry because it is so frustrating. I am retired so I cant afford to replace them. I just dont want anyone else to suffer the same frustrations!

MVWC200BW0 - Washer starts to fill and then drains before completing the fill cycle. Contacted Maytag through the live chat on their website (cant talk to a real person on phone). Since my one year warranty had been expired 12 days I was told to contact a certified repair person. They offered no help in solving my problem. Told nothing they could do, warranty had expired. Maytag will never get my business again. Now I know why the Maytag repairman is so lonely, people have quit buying Maytags.

Great appearance, great job on getting our clothes clean and dry. Good dryer cycle choices and output. Good washer cycle choices and output 98% of the time, BUT, sometimes the washer needs a do over about once in 50 loads. Overall, two thumbs UP.

I bought a new Maytag refrigerator on July 2, 2011. The ice continues to drop after removing your glass. Now you must pick the ice from the floor. Maytag said it has a 10 second delay and will continue to drop ice. Im tired of picking up ice and wiping water from the floor. Who wants a product that leaves a mess?

Maytag bravo - thought it would be a good brand/buy/new technology. Absolutely nothing to like. Complete junk. Bought it in June 2013. Doesnt get things clean and takes a long time to not do that. We thought a good reputation from a major brand would mean a durable efficient washer with a reasonable capacity and good features. Unfortunately we didnt know when we bought it what a bad design/investment it was. It has destroyed numerous garments with fraying and doesnt rinse soap or dirt out because it doesnt use any water.The bravo from Maytag is supposed to be low water efficient. Unfortunately, it doesnt use enough water to wash clothes, no matter how little or how much HE soap you use. It frays clothes, leaves soap residue, wont wash jackets or blankets or bulky things, takes forever to NOT get things clean, doesnt get heavy stains or mud out, the list goes on and on.... oh, and its expensive, and breaks down a lot. I cannot believe that there has not been a government recall where the people who were unfortunate enough to buy one have been given a large amount of money back.

I bought a front loading Maytag Cloths washer model# MHW3505FW1, SER# C71451407 new in April 2017, from Home Depot, since then it has broken down three times, with a water pump, a master board, and now another master board, we were told by the appliance repair service that is used by Home Depot extended warranty service, that it will take a month to receive the master board. Thats it... Never again will we buy another Maytag or Whirlpool product. This is unacceptable. Gone are the years when Whirlpool and Maytag made quality products!

I grew up trusting and believing in the name brand Maytag. Unfortunately, I wont anymore. I purchased a Maytag MDB7749AWM1 dishwasher from Lowes thinking that I would not need the extended warranty because well it was a Maytag and they just keep working and working for years to come. Not true anymore. 1.5 years after the purchase the control board has gone out. I come to find that hundreds upon hundreds of people have all experienced the same thing. Shortly after the manufacturer warranty expires, the panel dies. By all accounts it is an issue of POOR engineering and Maytag now being produced by Whirlpool. The replacement part is between $150 and $200. Thats about half the purchase price. It is a racket. Companies like this probably think, well if we build something that is going to last and last we cant make money on that. So lets rig it so our stuff breaks right after the warranty and charge half the price of the unit to fix it so we continue to make money either by people buying the part or just going and getting a new dishwasher. Well I can tell you I will be getting a new dishwasher and it certainly wont be a Maytag OR a Whirlpool.

I purchased the Bravos X washer approximately 13 mos ago. Washer was noisy and has deteriorated since installation. I questioned the ability of a non agitator appliance getting close clean but was assured it would. Not the best if clothes are just moving against clothes. The machine had a difficult time in between adjusting to wash balancing a 3x event upon starting. It leaked intermittently during spin cycles and stopped due to unbalanced loads, sometimes refilling and stopping again. Now it wont spin at all, circuit board problems! This is my first and last Maytag. The company will most likely not balance/compensate on the purchase price (like the Bravos X) because it is beyond the 12 mos warranty.

After speaking to a Kim today... Im more than angry. The control panel on my dishwasher is broken. Had repair come out and they told me a few months past warranty. Kim tells me the only thing still under warranty are the racks?! Im extremely angry at the poor service we are receiving but pleased as we have cancelled the washer and dryer (Maytag). If youre thinking of going Maytag or Whirlpool, cancel! Not worth the headaches or cost.

Top of the line $1300 Maytag Maxima MGD8100DW probably rusted much earlier before I noticed. After all how many times you check the drum of brand new top of the line dryer?? Manufacturer says not covered. Not sure but already this brand new model has been discontinued, so the manufacturer i.e. Maytag or Whirlpool take your pick found out about the defective design/part but now does not want to honor the warranty ridiculous. And one of the main selling points was made in USA (which turned out to be only assembled in USA), and the consumer reports which gave good rating but they were duped too.

Purchased less than a year ago, Machine stopped working. Approved service company says no error codes visible must be ok. Machine still does not work month later, service again does not show up for call, following month same. Its still in warranty but they claim it is fine. Error code disappear right after popping-up no storage of error codes.. I had to buy small washer to manage home. Really bad choice of product. Will not use this brand again.

Bravos washer is 4 years old. Started making an extreme amount of noise during the spin cycle. Had a repairman look at and showed me the bearings and area under the tub. $400 plus in damage due to bad bearings, rust to bottom of tub and surrounding area. Four years for a high-end washer is pretty bad. Needless to say, I will buy a new unit and would NEVER recommend a Maytag Bravos appliance.

We have a purchased a Maytag two door refrigerator a few years ago despite my wifes repeated request not to buy any Maytag product. We had a bad experience with another Maytag product in the past. Now like many others we are experiencing the horrible nightmare of getting a water leakage from time to time that floods our tiled floor and it is getting worse and causing damage to floor and other kitchen cabinets that are anchored to the floor. We had a certified technician who suggested us to thaw the freeze and then reconnect it back. We did what we were told but that did not fix the problem. My wife found out that there had been 913 complaints from consumers on Maytag refrigerators. Why Consumer Affairs is doing nothing about it and why there is not a recall of Maytag refrigerators. We will never buy another Maytag product nor will we recommend others to buy. Enough is enough being discontent.

We purchased the washer and dryer in June 2009. This past weekend, I noticed that the washer was leaking. The price to fix it is half of what a new machine will cost. I am very disappointed in Maytag. When I purchased the machines, I thought I was purchasing a quality product. Ive had paid much less for washers that last longer. Needless to say, I am shopping for another washer this week and it will not be a Maytag or Whirlpool. They are pieces of junk!

DO NOT BUY THIS MAYTAG REFRIGERATOR. Purchased 9-30-19. Delivered 10-4-19. 12-9-19 - Not Cooling, Called Whirlpool on hold for exactly 1 hour. 12-11-19 - Repair service here - ordered new Control Panel. 12-17-19 - New Control Panel Replaced. 1-6-20 - Freezer is not freezing. Control Panel going up and down and blinking constantly. Called Whirlpool - on hold for exactly 1 hour. They called service repair. 1-8-20 - Service Repair here and ordered 2 thermostats: 1 for freezer and 1 for refrigerator. 1-15-20 - Service Repair here to install 2 thermostats - At this time I purchased the extended warranty for $119.30 for 3 years.3-1-21 - Control Panel completely went out again. I called Whirlpool - on hold exactly 1 hour before they answer phone. I am so pissed. They call Service Repair. 3-3-21 - Service Repair here. They order new Control Panel. States these panels are continuously going out and they are having to replace them everywhere. 3-12-21 - I called Service Repair since we havent heard anything. ETA on control panel from Whirlpool is not scheduled until 3-19. I am really pissed by now.In the meantime I have been on hold with Whirlpool for 47 minutes. At exactly 1 hour being on hold, they answer my call. Im told I have to wait. There is nothing they can do. I told her we were buying ice every other day at $10.07 for 2 20# bags and they wont replace money. Told me to throw my items away and they would replace all the food for $250.00 one time during the 3 year contract period. The service is Customer service on their contract is terrible. Waiting for parts is even worse. This is a piece of crap appliance and we will never buy another Maytag.

Maytag dishwasher 5/3/2010 model MDB6709AWQ1. 12/20, 2015 it is dead, $69.00 service call. Failed user interface and main PCB parts estimate with labor $449.46. Called Maytag Co. We would pay the labor $139.00. MAYBE they pay the parts.

I have only had this Maytag dishwasher for 2 years. My control panel has gone crazy! The child lock is blinking and I never touched it. I have tried to clear it by touching the heated dry button for 3 seconds, every once in a while it will clear. It eventually will start blinking again on child lock. I did research and have found out that Im not the only one that is having this problem. I now have to get it fixed.

I purchased my Maytag double oven (MEW6627DDB) in November 2008. In January 2013, with a setting on 375, it heated to 440 in 15 minutes. The repairman said $650 because it needs a new control panel and 2 new sensors, one for each oven. I contacted Maytag as I felt this oven should not have gone out in 4 years. I spoke with Ebony and then a supervisor, Vana. Basically, I was told that since I didnt purchase an extended warranty, there was nothing they could do. While I have a freezer 40 years old and still going strong, I realize that appliances manufactured many years ago were much more reliable. I feel that Maytag should stand behind their products and should have offered to send me replacement parts. I know I would have had to pay labor for installation. Their answer was I should have purchased the extended warranty. However, one should not have to purchase extended warranties for products. I had every confidence in Maytag. Why else would I have purchased my first Maytag product? I should have stuck with Whirlpool, which I was recently told, now owns Maytag. Maytag customer service personnel were extremely unhelpful. I wonder how many Maytag employees purchase extended warranties for their appliances or if theyre smart enough not to buy Maytag.

I bought brand new Maytag appliances top of the line. I put the stove, dishwasher and refrigerator in and was waiting for the cabinets to be done before installing the microwave, It was a couple of years; I took the microwave out of the original box and had it installed and it made a terrible noise and then shut off. There is something loose or something. I called Maytag to activate my warranty but they said the time is up but I had never opened the box so I didnt know there was a time limit on sending it in. There was no customer service! The stove I bought for close to $2000 has had to have the control panel replaced 3 times so I have to pay every year for an extended warranty just to guarantee I have a stove. Last year I went through the holidays without one because it was out then too! I would never buy another Maytag again!

I have the Maytag Direct Drive Motor washing & dryer set the is supposed to be “commercial technology.” The washer is supposed to keep wet clothes fresh if they don’t make it to the dryer right away. After 2 years, I disagree in that it offers no better outcome than the much older machine I replaced. Furthermore the dryer cuts off leaving my clothes damp every single time, which I cannot stand. It leaves my clothes to wrinkle terribly and damp to stink if I do not collect them fast. I honestly wish I still had my old set. All the new features simply fail to measure up not to mention over complicate and add expense to repairs.

I had no issues with my washer. The best thing I ever did was stop using Sabrina softener in it and made the switch to vinegar. The worst thing I ever did was think that paying $900+ for a nice washer would get me more than a year! What a joke! I started noticing small leaks when my hardwood floors started lifting and once my husband looked into this, we realized there is no seal around the top of the drum. So there is no barrier between the drum and your floors basically. Then one day we had a flood. As we watched the cycle run, we noticed that when the water was filling into the bleach and fabric softener compartments it was coming in at such a high rate, it was spilling over the sides down to the floor. So we went to the internet and found a few complaints about this, but no answers. Thankfully we found one guy who had the exact same problem and even had pictures that matched ours. Luckily a real appliance tech answered him and he couldnt even figure it out but took a guess at what I might be: the water inlet valve. But that was just a guess. So we called around to find the part and talked with a few sales persons. One was so nice to even ask a technician standing in line. And he said that there was no way this could be it. But then we decided to take a gamble. We also noticed that both compartments were filling up at the same time, but the bleach should fill during the wash cycle and the fabric softener during the rinse cycle. So it was either the $104 water inlet valve. Or the $200+ circuit board. These are my options after already spending $900+.. So we went with the valve and thank goodness it worked!!!! It is so disappointing that after a short time, this washer broke and cause more damage to my floors. It is an awful design. I bought myself the nicest front loaders for my first house. When that broke 7 years later, I bought this washer because I liked the no agitator design without the smell of a front loader. Now when this one breaks again, Im not buying another HE machine. The majority of people I talked with today said that these HE machines are breaking down faster and faster as the get better and better. I am so beyond disappointed, angry and in shock that this washer failed in less than a year and a half time. My hope is that this review will give the answers we couldnt find without paying an arm and a leg. Is this what passes for quality these days???

Water ran out of washer and flooded my garage. 1) Replace computer. 2) Wrong computer. 3) Water still flooding garage. 4) May need water valve. 5) Showed up didnt know what to do, then left. 6) Whole new tub - 3 hour repair - 2 weeks until they have time to repair. Still waiting. HELP.

My Maytag washer MVWB400VQ was purchased four years ago and was used by two people. It started making a sound like an airplane taking off and is very loud. We called a service technician who said the outer tub was gone. I called Maytag to see if there was a recall or warranty of some kind. At that point I was told they do have a warranty but could not sell it to me because I had already had someone diagnose the issue. I paid $800 for the machine and the difference between the repair and the warranty was $40, so I thought it would be smarter to have some type of coverage if anything else went wrong. Nope they will not give you the coverage. The moral of the story is they really do not want to provide customer service unless you are unaware of the actual repairs needed so they can get more $$ from you.

The washer does not get clothes clean at all even with the help of odor blaster, does not spin right, does not even out the clothes, walks while it is spinning. My towels do not smell good at all. The dryer gets too hot and the lint trap is always a mess even though I clean it after every use.

My Maytag (MDBH955AWB) dishwasher (not even 6 years old) is losing its prongs that help the dishes to stand up. They are corroded at the bottom and snap right off, leaving the dishes without support and banging into each other. We are only a family of 3 so it gets moderate to minimal use. The bottom basket costs $200 to replace, a third of the cost of a brand new dishwasher. Everything else about it is fine but my dishes will be chipping away. I cant believe Maytag made the basket so poorly that it doesnt last the lifetime of the dishwasher.

Our bottom freezer began building up ice. We cleared the ice and unclogged the drain gasket as per the many instructions that we found online. Researching this problem, I discovered very quickly that this is due to a faulty design of the drain grommet. A new part has been substituted by Maytag. I called Maytag customer service and they refused to supply the replacement at no cost to me and claimed there is no quality issue. This is not about the $20 for the part. It is a leading consumer brand disregarding customer satisfaction. This is also bad business. They will sacrifice their reputation for a $20 part on a $1,000+ purchase. They need to be put on notice that they cannot get away with this in the age of the web where there is total transparency.

Dishwasher worked fine for the first 12.5 months, and lo and behold 1 month after the warranty expired, I had my first repair, a new motor. A few months later, I had my second problem, the thermostat. A few months later, I called Maytag because I thought that the control panel was probably shot (based on my previous Maytag for which I replaced the control panel 4 times, before Maytag finally agreed to get me a new dishwasher). At that point they sold me an extended warranty which for 300 they would make this repair, and any other repairs for the next year. They have been out 7, yes 7 times, in 4 months. They would probably be out more often, but since it has been difficult to get a repair person out here, more time than not Im washing dishes by hand. Their customer service is horrible, their products worse. Still waiting for the dishwasher to be repaired. They wont send out a different company, even though they have been out here 7 times, and keep coming back. Even when it is repaired, they will not cover the cost to replace the soap bin, the racks, the wheels on the rack, and all the little pieces made out of the same quality plastic as the stuff I buy at the Dollar Store (except when that stuff breaks, it doesnt ruin my hardwood floors). Dont buy a Maytag, roll up some $100 bills and light a match, because you can look at a pretty flame and wont raise your blood pressure dealing with their customer service.

Maytag Bravo Washer - I recently purchase a fairly expensive washer built by Maytag. In my opinion it is the worst washing machine I have ever owned. Again in my opinion their advertising about being such a reliable company should be considered false advertising, and near criminal. If you had a lower rating I would use it. Absolutely you should never use the word Bravo in a description of this washer. I will never purchase a Maytag appliance again. Check the internet for reviews before you purchase. I had just came out of surgery and in a wheelchair and trying to move back home and didnt do my homework.

I have a Maytag dishwasher and the bottom rack has rusted out so that it cant hold dishes. The dividers break at the bottom. I was told by Maytag parts that this is a common problem and theyre hearing from a lot of consumers about this, but it will cost $196 to replace.I spoke with customer service who told me that dishwashers only last 8 to 10 years” and since mine is 8 years old, I should expect that it would rust. Thats unbelievable. They wont replace the rack, nor offer it at a discount.

Like many others Ive read about online, our Maytag fridge model MFI2269VEW5 with bottom mount freezer has ice forming at the bottom of the freezer compartment. The ice then melts and runs onto the kitchen floor. At this point, I am able to prevent this leakage problem by removing the 1/2-inch layer of ice that builds up about once a week. Using a stiff plastic spatula, I am sometimes able to remove the ice in one large sheet but usually it breaks up and has to be removed in pieces. I have seen several videos online showing how this problem can be fixed but as a pensioner with limited income, I am sure the expense of a repairman would be prohibitive. I could likely make the suggested repairs myself but because of a knee replacement, I am not able to kneel for any length of time so that is out of the question. Besides, when we purchased this fridge 3 years ago, we expected it to run trouble free for the rest of our days. This is obviously a design problem and Maytag should be covering the cost for all repairs. However, it is a sad reality that Maytag and their owner, the Whirlpool Corporation is only interested in making a profit to satisfy their stock holders. They apparently only pay lip service to making quality products that last and customer satisfaction seems to be a thing of the past.

We purchased this Maytag washer. My wife liked it at first, but after a few months she kept complaining the wash stinks, and I can also say that. I complained to my wife about the smell of our wash, especially the wash towels. The wash was turning colors and some we threw away. My wife has been complaining about all this for months and years and said she will never buy another washer like this. Then about two years ago, she was having trouble with codes coming up. We called service, but didnt get any help, so I looked on internet and found the problem with the code. I took the washer apart and cleaned the tube out and the washer worked, but every now and then my wife needs to climb over washer and unplug, let sit, then replug back in and start it to get rid of code. My wife and I are very upset with this washer!

First of all, the hoses that came with my washer leaked and were cheap made. My husband put the hoses from my old washing machine on the Maytag. Then, I hadnt had my Maytag washing machine but about two months when I had a problem with the mixer. I had to turn the hot water connection off in order to wash in cold water. When I called the store to explain the situation and ask if they had their own serviceman, the person I talked to made me feel like a complete idiot. He said in his twenty something years of selling Maytags, he had never heard of such a thing. Anyway, when a serviceman finally came, he also had to replace another part due to a recall. Now, my washer is right at four years old and is leaking from under it. My husband checked the hoses, and they are not the problem. I bought a Maytag thinking I was buying the top of the line but I guess I was wrong. I will not buy another one nor recommend them.

Our circuit board has went out twice. The stove is not designed well. The oven vent sends hot air over the plastic panel / circuit board. It melts... The first one was under warranty and the second, only three years later, was not. This is a very expensive part and Maytag will not even talk about giving me a discount.

Bought a new Maxima washer in January. Worked for one week. Got error codes and electronics board shut down. Contract serviceman says board should have reset after turning off. Ordered new board and it is missing one of the electrical wire connector plugins. Maytag/Whirlpool is having a problem with these boards.Three weeks without a washer. Two days off work. When it goes out again, days off work will be close to what I paid for it. Thinking I may cut my future losses and buy another brand when in-transit board goes out.

Convenience, small, clean while you doing other jobs, it cleans while you sleeping, it's not loud, not expensive, comes in different sizes and colors, it's another helping hand, you will love it, it's worth the money.

At 14 months old Main computer box failed, caused the machine to shut down on unbalanced load ($400). At 28 months old Main computer box failed, caused the machine to shut down on unbalanced load. In addition when the service guy was underneath the machine to change the module he noticed the stator housing to the motor was falling off. He said he never saw anything like it. After reading about all the problems people have with these machines I have talked friends and relatives out of making the same mistake of buying an old and trusted brand like Maytag. .

We purchased all new appliances 3 years ago including a Maytag dishwasher. Same problem as a lot of others. We had the control board fail three times in just four months. Now today the repairman came and while he was here contacted other Sears technicians and Whirlpool technicians. They came up with the idea to replace the detergent dispenser which they said is causing the main control board to fail. However, while the tech was on the line with Sears and Whirlpool they done troubleshooting on the detergent dispenser and found that it was all within specifications. In fact, that was not a problem because it worked as it should. But in their wisdom they decided to replace the detergent dispenser. We now have to wait another ten days for the part to arrive and reschedule another appointment to have the detergent dispenser that works replaced. The serviceman that was at our house said that they are making him replace a part that is working and that this does not need to be done but he has to take instructions from Sears technicians. Our service person said that he doesnt anticipate that replacing the detergent dispenser will make the dishwasher work but he said if it does it will only last a few weeks as before and then fail once again. We have the dishwasher on extended warranty and there are about 22 months. I suspect that this one will be going to court to get resolved. Never Maytag again or Whirlpool.

The refrigerator is not keeping cold. The freezer is full of frost/ice. I had this fridge looked at twice in the past. Its about 6-7 years old.In the past, Maytag was considered a high end product. I wonder where the manufacturing is taking place for most of the parts. Could be it was cheaper to go overseas and now we are all paying for unacceptable products.I will never purchase Maytag. Maytag should be selling products they can stand behind! Products that are made in the USA, where our standards are higher and we expect products that work!