Purchased washer in Jan 2013. Average usage is 1 load per week. Last week the washer started leaking from the rear left side. A service call discovered that the bleach dispenser was filling up with water and overflowing. Bleach dispenser?? I never use it! Seems that the new bleach dispenser hose line has a relief valve whereas the original part did not. Internet research has confirmed that this problem is very common with this make and model. However, a call to Maytag requesting what compensation, if any, would be available resulted in a response that basically was too bad... so sad... cant do anything for you! Seriously? An apparent common, known problem and all they can say is we understand your problem. Needless to say that will definitely be the last lonely repairman Maytag that this household will purchase.

Purchase a Maytag washer in 2012 and less than 4 years later have to go shopping for a new washer. Purchased a Maytag because was under the impression that it was a good product and would last. Not true. The washer almost caught fire, just happen to be nearby when smoke started coming out from behind the washer, so I was able to turn off the machine and then unplug it and my husband smelt wires burning. If I hadnt been nearby we could have had a fire instead of smoke. I dont want to rain on anyone parade but I wont be recommending this product to anyone.

I purchased a range 5 months ago. It is STAINLESS STEEL. It began to rust. I called customer service and they told me it was cosmetic, so they wont help. I think a stainless steel range should not rust after 5 months. Very disappointed, WILL NEVER BUY MAYTAG Again.

We have a 2 year old Maytag washer and dryer. 10 year warranty may I add. Well, we get 2 frantic calls that say, “They heard an explosion and the bottom of the house is flooded.” An explosion so violent that it shook our 3 story house and sounded like a bomb went off. Our washer and dryer are on the main floor. When we get there we found the washer top was dented so bad that it dented the bottom of the dryer that sat on top of it - blew the dryer door open! Blew the front of the detergent compartment and blew the side apart! Scared my mother and father in law who lives downstairs and who is bound to a wheelchair! Not to mention the fact that it flooded the basement and ruined the ceiling and Maytag says they will replace the washer! Are you serious? Who wants another washer which may or may not explode! What about the damage to my house! This just happened a couple of hours ago! We are very ticked off and not happy with We will replace the washer! Bad, bad business. This is not where it ends! I want my house repaired and won’t settle for anything less! Shame on you Maytag for putting profit above quality! Consumers beware!

We had a repairman come out and take a torn pillowcase out that was jamming. It worked for a couple of weeks, now refuses to start. We have decided to rid ourselves of the Bravos 300 washing machine and not deal with Maytag any more. I would not advise anyone to buy a washer of this type, as it never really got the clothes clean to begin with.

This washer had good reviews when we bought it, but now today the agitator is not working. I see there are now 100s of bad reviews of this machine most around the same 1 1/2 year mark. How unacceptable to have a large appliance like this break after such a short time. Ive called Maytag to see if there was a recall and there is not. They offered the extended warranty to me for $325 that would cover all parts and labor. Ridiculous.

I would like to start with, my Mother had always used Maytag washer and dryers. Her machines would last 20 years or more. I bought a Maytag front loader washer and dryer in 2006, since owning these machines have spent in upwards of $1400 in repairs. Some being flood out of tub, mother board blow out a couple of times as well as various other issues. The biggest problem is the awful smell of our clothes, I must wash clothes multiple times to try and remove these smells. I tried contacting Maytag and they dont want to hear my complaints and push me off to purchasing another washer and dryer. Oh, I will be buying a new washer and dryer it just will not be Maytag. Do yourselves a favor and DO NOT buy another Maytag. This is not the same company my Mother knew and trusted.

I have trusted Maytag for many years, more than 60 years, my parents and then myself. My Dad always told me I could trust Maytag over any other brand and that has always been true until I bought a new Centennial Econoserve Washer. This is without question the worst machine ever made. I should have asked every question in the book concerning this machine but, oh no, I just trusted the name MAYTAG. I am so sorry. I cant trust it to clean anything that shows it needs cleaning so you have to wonder what does it clean that you cant see. Im sorry people, I just dont know what to do. I cant afford to buy a new machine and the store I purchased are basically telling me, Sorry, you bought a stripped down model. Too bad! I will never buy another appliance from that store nor will I recommend them to anyone. Too bad since they are locally owned. Anyway, Maytag, you blew it badly to turn out this terrible machine. Thats my story and Im sticking to it. Better product next time.

Purchased a Maytag Bravos 300 quiet series and am totally dissatisfied. I have a bandsaw, router and several saws in my workshop and by far my Maytag washer can drown them all out with the noise it makes. On top of all this it does not complete its cycles before it shuts off and if you try to restart it you never know where in the cycle it is going to start at. This may occur six or seven times before you are able to complete one wash. It may take a day to wash one load of clothes. Maytag should refund the total purchase price of this piece of junk!

We purchased our Maytag Refrigerator Model # MBF2258DEHM on 12/21/2015. Just a couple of issues I would like to bring to your attention before you purchase your Maytag. The single refrigerator door does not close automatically. You have to close the door. The metal handle is metal and has a metal smell and feel to it. The stainless steel door and the handles are not the same finish. Although this might not be a problem for some who like the industrial look I prefer my hands to be free of chemicals while I am preparing food. The ice maker takes up too much room. The ice maker should have been an option, not a standard item. I had a Kitchen Aid for 10 years and loved it. I thought I was going to have my Kitchen Aid for 15 years or more. I would have purchased another Kitchen Aid, but the reviews were not good.

My wife & I purchased our Maytag dishwasher model # MDBH979SAB1 on 3/8/13 from homedepot.com. Approximately 24.5 months later our dishwasher experienced control panel light button malfunctions similar in description to the many other consumer complaints on this & other forums. I would like to share some additional information based on my research about this issue and possible fix. The source of Whirlpools control panel issue is design related. The issue is caused from moisture which induces oxidation on the Flexible Printed Circuit (FPC) cable that is integrated with the control panel and connects via connector to the electronic control box. The issue usually manifests itself on the cable just where it bends coming out of the touch membrane panel.The oxidization of the FPC cable eventually creates electronic shorts or opens between the parallel traces thus causing the panel control lighted function problem which disables the dishwasher from being used. The cable, since integrated with the control panel, is not a separate replaceable part. In order to repair, the Whirlpool diagnostic action is to replace the entire control panel. I quickly learned after doing some online research about Whirlpools control panel issue that it extends back to at least 2011 with control panel part # W10475784 and corresponding or like PNs of this design. The number of control panels sold of this design by various online appliance part centers coincide with the high number of reported like control panel failures.In just 2015 alone so far, the sales for this control panel have been in the hundreds. This indicates that Whirlpool continues to replace defectively designed control panels upon failure with defectively designed control panels. There was also a class action lawsuit filed against Whirlpool in the state of California on May 6th, 2013 for the control panel issue. The filed lawsuit is public & the whole document is available online as a pdf file. Unfortunately, Judge **, granted Stipulation to Dismiss Case with prejudice 74 on 5/23/14. I was unable to find out any details as to why the case was dismissed. I did not call Whirlpool about my control panel issue, instead I handled all correspondence through Email to them at WHIRLPOOL_CUSTOMEREXPERIENCE@WHIRLPOOL. COM.My initial correspondence included all the facts about this issue & that I did not wish to have their warranty coverage/period explained to me for I understood them, the problem was a quality issue, and just basically wanted to know what they were going to do or have been doing about resolution. The email correspondence with them got me nowhere. They initially replied back with all the form niceties like We apologize, We understand your frustration, & We value you as a customer, but denied every knowing about such control panel issue, regurgitated their warranty policy & period and were unwilling to resolve anything. In their last reply they stated how unfortunate it was that customers only take the time to provide negative feedback!! This is just bad business, and though I would not like to think it, but the control panel issue may have been by marketing design.Please keep in mind that Whirlpool manufactures appliances under at least 15 different name brands including Maytag, Kenmore, Admiral Kirkland, KitchenAid, Roper, Speed Queen to name a few. All is not lost, being an electronics engineer I looked into the do it yourself fix. If you are not comfortable in doing this, you may be able to find someone to help. I was able to repair mine by carefully scraping off the oxidation from the FPC cable (will appear brown in color) & encapsulating it with high density 100% dampening silicon (non-caulk type) to protect it from moisture & withstand heat. There can be other ways of protecting it from moisture instead of silicon, just make sure it can withstand heat, wont become brittle, & that it may not cause potential damage to the cable itself.My repair has worked for about 4 weeks now, & shows no sign of oxidizing. The problem may be more severe if the oxidation has actually opened or broke one or more of the small cable traces. Do not attempt to solder this cable! Its way too thin & will only make matters worse. An open can be carefully bridged with a conductive glue or ink thats on the market. One source is a window defogger repair kit product thats sold at auto stores that has a conductive glue in it. Post open repairs will need to be checked with an ohm meter to make sure repair is good and that any adjacent trace lines have not been shorted by repair. Of those of you that have just bought or had installed Whirlpools defective control panel, please encapsulate the FPC cable as soon as possible to protect it from moisture. If you dont, it will surely oxidize again over time.

Maytag Quiet Series 200 only 1.2 years old: I moved into my home about 2 months ago and the touch panel on the dishwasher, which is of course just past the warranty expiration date, has progressively gotten worse until now, doesnt work at all. I have tried calling Maytag many times on numerous occasions, who apparently only has one phone line because its ALWAYS busy. The cost for the touch panel on this dishwasher (model# MDBH945AWS3) is $150 which isnt even worth fixing since I can go to Lowes and buy a new FRIGIDAIRE for $300. The problem is the circuitry from the touch panel to the control board gets too much moisture in it with no protection around it. If I were them, I would find a way to make all these parts separate so regular people, like you and I, would be able to buy parts a lot more cheaply and repair these items ourselves. However, since the front panel and the circuitry attached to it is all one cohesive unit that cant be taken apart from one another, nearly at all without ruining it, then I might have been posting a different review here. However, that is not the case. IF I could actually get in touch with Maytag, I would ask why on earth isnt this a recalled item and when they are shipping me a new part since it seems everyone is having the same issue with their Maytag dishwasher, no matter what series it is. I do not plan on buying a Maytag appliance in the future. I do plan on buying a Frigidaire since the rest of my appliances (stove, fridge and overhead microwave) work perfectly without any issues whatsoever.

If you have a second floor laundry room, DO NOT, and I repeat, DO NOT acquire this washing machine!!! The Bravo MCT model washer is TOO loud (during spinning cycle), and for some reason, the clothes come out all tangled up. Some cycles are a waste of a cycle, and most cycles take a bit longer than my former washer. I miss the cycle choices I used to have on my former GE Profile washer (GE does not make that model anymore hence my changing brands). For the most part, clothes come out clean; thats why I give it a two-star rating instead of one. The dryer: Must dry every load in low heat so it doesnt come out extra crispy and wrinkled up. Although I generally have to run a second drying cycle, low heat does work great and the clothes come out ready to be folded/put away.

I purchased this Range about a month ago and would return it to the store if it wasnt such a hassle. The set of grates that came with had 1/4 drop from the center to front of stove. Whirlpool sent a new set; they were no better. Then customer service wanted to send a Tech out to see if the grates were out of spec. If they are out of spec they will replace. If not I will be charged $89 for a service call. Whirlpool customer service assured me their service rep would have new grates on his truck. So I drove to their service provider, he laughed and said imagine they want me to send a service Tech out to look at cooking grates and NO they don’t stock them. If you want a cooking surface that is level and does not SCRATCH BOTTOMS all your cookware. The convection oven is also a joke. In order to bake something in the specified recipe time, I have to set bake temp 25 degrees higher to compensate for convection ovens automatic temp set back feature. When I turn on LF burner flames engulf 10” pan, a truly fire hazard. I have a Maytag dishwasher and dryer, love them both. Maytag should stick with dishwashers and laundry. I never have been more dissatisfied with a major appliance. I would NOT PURCHASE THIS PRODUCT.

Maytag bottom freezer / refrigerator: What a low-quality operation these guys are operating. We have a 5-year-old double door unit, which is not a cheap ticket item; and we thought that Maytag was from the days of old. The compressor failed along with ice makers and some high-use parts inside. I can understand the plastic lids and guides wearing out with heavy use, but not the compressor. I called Maytag and was directed to their proud Tennessee Service Location. It might as well be in China, where the real owners are located. She said, Oh well, we build quality units that are to last 12 years. However, they are man-made, and you cant count on that being a positive thing. What arrogance. I might get stuck with another brand from Asia. But it will never be a Maytag or any other in their family of products. The repairman is really busy these days.

My name is Mrs ** and I dont have a complaint. I would to tell you about our washer. It is a Maytag. It use to be my mother-in-laws. She did laundry in it for 4 grown boys and 1 girl plus her and her husband. She passed along to my husband a long time ago. And now it does laundry for 6 kids plus my husband and me. I run it 2 days a week sometimes more. The washer is between 25 and 30 years old. And works good still. Im not sure how much longer it has but we are happy with it. And soon Ill be washing for 7 kids. We have made a decision to start looking for another soon. But I wanted to share my story with you. My husband is now in his 40s if it says how long it has lasted. Thank you.

Washer knots clothes into unmanageable tangle. Poor rinse leaves soap scum unless rinse extra, thus not conserving water as appliance is supposed to do. Load easily becomes unbalanced and unable to restart machine if paused to rebalance load. Will never buy another Maytag washer or dryer.

This one of the worst purchases I have ever made! Paid over $850 in March, 2015 for the Maytag Bravos XL. At first, we experienced leaking and now there is a terrible banging and clanging noise! Had an appliance repairman come to see what was going on. Apparently it needs a hub replacement and bearing replacement. Was told by two companies that it is not cost effective to fix it due to the amount of parts and labor.Aside from this major issue, I never felt that the clothes came out clean. Many times, the clothes would come out with detergent all stuck to the clothes and had to be rewashed. The softener and bleach dispensers are not removable and it is nearly impossible to get all the way into the cup in order to clean the mildew that builds up. The fabric softener dispenser always had gummed up chunks.Called Maytag several times to no avail. Was basically told - too bad its out of warranty. I have never heard of a washer giving out after 3 years! The worst part is that I have searched many places on the Internet and apparently the bearing problem seems to be a common issue with this washer. I purposely bought an American made product and am extremely disappointed in not only this product, but the company as a whole. The customer service department is awful. I will NEVER purchase Maytag or Whirlpool ever again. They lost my business for putting a terrible product on the market and refusing to acknowledge flaws. Interesting that this model is now discontinued, but they refuse to acknowledge the problems. Stay away from Maytag and/or Whirlpool!

Maytag Cenntenial Washer - We traded our super capacity for the ex-large Maytag washer and we have great regrets. We posted it on Craigslist about 4 months after we bought the unit and NO ONE would buy it for $300.00 even though we paid close to $600, and only 4 months old? What does that tell you? I have had to add 5 gallons (bucket) with each wash to make sure all the soap washes out. Very loud, takes a long time to wash and just worthless. This last weekend, we tried to trade it for a used $150 agitator washer with a used appliance store and they said theyd never be able to sell it and refused the trade. What does that tell you about the washer?

Im so mad over my new purchase on the XL Bravo washer and dryer and Home Depot will not return. I have 3 kids and a hard working husband. My clothes do not come out clean no matter what cycle I use. It takes forever just to wash one load. If you spill something on your clothes and it dries crusty it will come out of the washer crusty. I want to cry. So much money wasted and cant get our money back. Would never recommend a washer without an agitator. Towels come out soaking wet, and dont spin dry if heavy...forget washing a blanket. 4th day using the dryer and now there is no heat. What was I thinking!! So mad and sad too!

I built a new home in November of 2013 and filled my house with all brand new top of the line Maytag appliances. Almost a year and a half in, my $2500 refrigerator is broken and all my food is lost. They send a repair man out; and guess what, the warranty is expired. So they wanted me to pay $800+ to have my refrigerator repaired a year and a half after I purchased it. I cant believe they have no shame in sending out products with their name on it that only last 1 1/2 years! I would never treat anyone like they treat their customers. They hold no responsibility. Their name holds no value to me anymore. I was extremely disappointed.

We bought commercial Maytag washer & dryer Oct 20th 2020. Very expensive ones. Oct 13 2021 they stopped working so had it checked. The shifter on washer went out & dryer blower is not working really!!!! Not even a year! Been without washer & dryer for 1 month because they didn’t have availability & now have to order parts another 2 weeks!! Never buying this product again!! Don’t buy Maytag!

We bought a Maytag dryer from Lowes on 4.23.20 for $567.87. From Day 1, it required us to dry even medium loads at least 2 times and sometimes even 3 times. I have been complaining to my husband since we got it. The clothes come out smelling almost burnt. But if you dry it once, the clothes are wet. And if you try to dry it the 2nd time for less time, its still not dry. So, it takes forever to do laundry. This morning, it sounded like a lot of metal was rattling around. So, I looked inside to see if change was in there, and nothing was in there but t-shirts and socks. It had been drying for less than a minute, but when I opened the door a wave of extreme heat hit my face. Now Im afraid to use it because I think it will eventually burn our house down. And with COVID-19, we do tons of laundry. We cant afford another dryer but may have no choice.

I bought my Maytag about 3 years ago. Have had continuous problems and now the whole barrel has broke and dropped down. I was treated with disrespect from the repair man and will never buy another Maytag washer.

We purchased a TOP of the line Maytag dishwasher with the expectation that we were also purchasing high quality. Boy, were we wrong. Continuous problems with the controls since out of warranty. The controls are in the door and operate pushbutton from top. This is electronic pushbutton not actual pushbuttons.MDB89595SBS.

I purchased this relatively expensive range and could not have imagined how dissatisfied I would be. The Aqualift cleaning technology does not work. There is no way to clean the oven door. They stress not to use oven cleaner, but as the Aqualift system does nothing to clean the oven door, there is no choice but to use oven cleaner, which they say will ruin the oven coating. Also, the grates are very heavy and it is impractical to clean the range top. I wish I had researched further; this product is a MAJOR disappointment.

I purchased Model #MGR7661XB (Gas Cooktop and Oven) in November 2009. From the very beginning, we realized it was a mistake and looking back, we should have sent it back.The finish, both on the stove as well as the burner racks (the removable grate that the pan sits on when cooking) has some sort of coating that instead of repelling grease and food seems instead to actually attract it. Any hot liquid or grease actually seems to melt into the finish and becomes impossible to remove. Essentially, our stove was ruined within the first week. We have even tried putting a scouring pad on a wooden spoon and scrub with as much force as we can muster - to no effect. Short of using a putty knife, and completely destroying the finish, I cant think of any way to resolve it.As for Self-Cleaning ... yeah, right. Use for entertainment purposes only. It doesnt clean at all.The latest issue is now the oven lights about 20% of the time. The broiler still works and we have discovered that we can trick the stove by allowing the broiler to heat up the stove to about 200 degrees first - then, when the oven is already hot, the oven part will ignite.Speaking of igniting ... from the beginning, this stove has the loudest ignition system I have ever heard. You can hear it ignite click/pop from two rooms away and the oven cycles on/off every 10 min. or so. It is very annoying.All I can say is, never again will I buy another Maytag. This was supposed to be the upgraded sealed burner model (which also is impossible to clean). This stove is only 4 years old but it was a mistake from the beginning. Like I said, I should have returned it after the first week.

I purchased all Maytag products for my new home three years age. The dishwasher stopped working 13 months after we purchased it. Since the home was under renovations for the first month, we only actually used it for 12 months. When I called Maytag, they told me that it was either the control panel or mother board and that they could not do anything because the warranty was only for 1 year... and didnt offer me anything to make good on this...NOW three years later, my microwave is displaying error code SE.. control panel is bad. Now I have not had a working dishwasher for two years and this just added salt to my wound. I called Maytag furious that this keeps happening with new products. The only thing they would offer to do is for me to purchase an extended warranty at $350.00 and they would have a repair guy fix the microwave. A brand new microwave would cost the same thing???? They flat out told me that there was nothing that they would do for me, and that they were not going to fix it for free.I filed a complaint with them and never heard back from anyone at Maytag. It seems strange that the control panels craps out within one to three years on two of the four Maytag products I purchased. I WILL NEVER BUY MAYTAG AGAIN... I went back to Home Depot and told them that MAYTAG has LOST me as a customer and that I purchased 4 major appliances from them and two stopped working with in 1 to 3 years. Home Depot was shocked and gave me $100.00 towards a new dishwasher. And I did not buy a Maytag.... I still do not have a working microwave... But when I do have the money to replace it, it will not be MAYTAG. Looking online, I notice a lot of the same complaints about Maytags control panels...... Could it be a scam on Maytags part???

Purchased an expensive brand new home which had Maytag appliances in it. After about 1 1/2 years the freezer bottom began to constantly freeze and drip onto my floor. I researched the issue and found it was common, simply thaw the area where it freezes. Did it multiple times, we do not overfill our freezer etc. We must take the ice out of the bottom every 4-5 days. My hardwood floors are destroyed now. We purchased a Samsung fridge freezer bottom when they first came out years ago, had it for 7 years, 0 issues, but it went with the house. Now my Maytag oven door is locked shut, also it takes a very long time to boil water. Maytag junk. I am going to buy another Samsung fridge tomorrow.

We purchased a new Maytag dishwasher for $500 from Home Depot about 1 year ago... it stopped working 4 days ago. I did not get satisfaction from Maytag customer service as they tried to sell me a repair program whilst I was trying to determine if it was under warranty as it is a known problem. I now have a repair person coming out with a price of $189.95 + time. A complete joke of an organization. Lesson? Do NOT purchase any MAYTAG brand. They DO NOT stand by their product. My rating is ZERO STARS, the site forces me to enter a star which is ONE TOO MANY. I will NOT do business with Maytag, Whirpool or any of their brands again.

I purchased this Atlantis dryer several years ago. To this day, I have replaced the rollers and drum three times. What a piece of junk! This will be the last Maytag I ever own.

Purchased Maytag dishwasher from Ft Knox Exchange in 2011, Model MDB6709AWW1; Serial # F04117463. Like most posts before me, the panel started failing after 2 years. Unit is now inoperative. I am attempting to fix myself using repair techniques Ive found online as I refuse to pay hundreds of dollars to repair this piece of junk. Will never buy Maytag again.

We just replaced our 20-year-old washer and dryer for a new Maytag Bravos set. The Home Depot staff convinced us that top loading units were of good quality and reliable. We were fairly satisfied with our expensive purchase when our washer stopped spinning. We are just past our 1-year warranty of course so we called the service department. A young man in a beat-up pickup truck showed up and spent his time reading the manual that was hidden under the washer. His best guess was a $300 part plus a $100 fee for him to show up. So to repair a less than 2-year-old machine is $400. Im tempted to buy a different washer. It wont be a Maytag, unless you can convince me otherwise. I give you credit for great advertising! I was convinced that Maytag was a good name with limited repairs.

Purchased Maytag Jetclean Dishwasher Model # MDB7749SBM3 on March 19, 2014 and on June 10, 2017 the washer would not go through the cycles properly. So I got on the internet to check out the problem. Maytag has very flimsy wiring circuit on the back of the control panel that rusts out due to being close to high-temperature water. Obviously a design flaw. The only way to fix it is to replace the control panel for $150 dollars with another flawed part. Do not buy Maytag dishwasher.

Our Maytag Atlantis dryer had smoke coming out and almost had our house on fire! Had it not for us double checking the entire house would have burnt down! The dryer is less than 10 years old and already it is tearing apart. I cant risk using it again. Terrible company. I would never buy Maytag products ever again!

I have had this washer 4 years...I bought this washer in May 2016. It makes 3 very loud noise as it moves into its next mode/cycle. Found out this is normal. IF, it is close to your living room, IT is loud.. I called again, saw that it was not filling up. 1/5/2017.. IT will NOT fill up to wash my clothes properly, clothes were still dry!!! Came out, (they sent a company near my area), said everything is right. I have tried, by sending messages, many times to get them to check. No one seems to care. The machine allows water to go out the bottom, rather than fill in the machine. I watched it myself. THERE should be a recall on this machine, definitely, something is sooo wrong.. I NOW have to put it on BULKY SHEETS full time, to get my wash clean.. NO energy savings there... BUT my clothes are finally clean!! Seriously, something is wrong...

I bought a dishwasher from Maytag model #MDB774SBW0, in 2013, last year prior to the year warranty it broke. The control panel had to be replaced. This year its broken again. Control panel not working properly and its starting to rust on the outside in the corner. Per the company unless the repairman damages it out theres nothing they can do. I cannot believe this piece of junk. First of all it costs so much and has broken twice for the same issue in 2 years. Will not buy another Maytag, very unacceptable.

We bought the Maytag washer from Home Depot on 5/4/2011 and it quit working on about 7/2014. We had a repairperson look at it and he said the drive transmission is worn out. He recommended that we buy a different machine since the part does not hold up since the part is made out of a plastic fiber material that does not show up. We bought the Maytag because we thought they had good products but a 3 year life on a wash machine is not acceptable. It is installed at our cabin so we only use it part of the year on limited bases.

I am a WWII vet. I bought a Maytag dishwasher 4 years ago from Home Depot... Cost me $600 in total repairs. Maytag would not help. My son just brought it to the dump! At that same time I bought a Maytag bottom freezer from Home Depot... It has never worked right. Ice dispenser broken after 1 year, food freezing in fridge at any temperature... It just died! Maytag refuses to take any responsibility for THIS POS!They should be ashamed at the way they treated me. I am 94 years old, and have fought for our freedom, and was looking for one simple thing from this American company. Its called fairness! Maytag sucks! You have lost a lifetime customer. You have lost my son as a customer, and will lose anyone I talk to, as well as my son posting on ALL social media! SHAME ON YOU MAYTAG! SHAME ON YOU MAYTAG!

My Maytag washer has been a problem since we bought it. Maytag washer has been repaired 3 times. Stopped working again. I am 78 years old, I have take myclothes to the laundry mat. First, waiting for the repair then waiting for the parts. If Maytag stands by their product they should replace it.

We bought a Maytag refrigerator around 2 yrs ago. Ive had repair out a couple and tried to take care of this myself. I am being told by repair men that it is a design flaw that the line gets plugged and water pours out all over my floor. The refrigerator I replaced was 20 yrs old, never had a service call & never poured water all over my floor. From reviews Im reading Im not alone in this problem. Needless to say Im less than happy with Maytag at this point! Model #:MBF1953YEB3, SER. #:K22812455, reciept #:** pd 1/19/13 DECKER & SONS 430 FULLER GRAND RAPIDS MI.

Our oven is 3 years old and the last time I used the self clean option caused the control panel to malfunction. Now we have to buy a new panel. The repair guy online advises people not to use the self clean as this is a common problem!!! What? I cant use that feature? That is so ridiculous!!! Now we have to pay $300. Whatever happened to the Maytag claim to quality and you would never see a Maytag repair man? Something needs to be done about the problem of appliances and electronics being so poorly made and basically disposable.

In the last 6 years, Ive had a Whirlpool dishwasher that the motor seized due to poor design and overseas Asian motor builder (3 years of normal service). I cleaned the motor and it seems to barely work another couple of months but the design and manufacture process was garbage at best. Thinking I would go with the best produce MAYTAG (Old commercial about repairman having no calls), only to find out that it too was bought out by CRAPPY WHIRLPOOL and it too lasted a couple of years with cheap MADE IN CHINA electronics!!! Thats why we are the laughing stock in the world as far as products.I remember the days of where built in the USA was the best of the best, now with selling our great nation down the toilet so some Wall Street Commie can make his/her biz-zillion dollars and sell this nation down the toilet. Maybe they need to go down to Arlington and see who really has paid the price for their luxurious life-style!!!

In late March or early April 2010, I purchased a Maytag Microwave from Sears in Ocean, New Jersey. The microwave was installed by Sears technicians on April 9, 2010. The total price for the microwave and installation was $356.53. I specifically purchased the Maytag brand because of Maytags longstanding reputation for quality products with long lifespans.On October 5, 2014, the microwave became inoperative and displayed a code of SE. On or about October 9, 2014, I contacted Maytag Customer Experience Center, via email, and advised them of this problem. I also wrote to Maytag explaining the situation. On October 15, 2014, I was advised via email that, as my warranty had expired, any repairs were my responsibility. I requested that my email be forwarded to Maytags CEO for consideration and review and was advised on October 20, 2014 that a Maytag supervisor would call me within two to three business days (of October 20th). After a follow up letter to the CEO, I was again advised on October 28, 2014, that the microwave was out of warranty and any repairs were my responsibility.I should add that I contacted Maytag Repair Service and was advised that the price of the repair far exceeded the price of the microwave. I feel that four years is not the expected lifespan of a microwave, especially a Maytag, and can only conclude that the Maytag microwave which I purchased was defective. I have purchased less expensive microwaves that have lasted for at least ten years. I got absolutely nowhere with Maytag personnel, found them to be curt and dismissive and would NOT purchase another Maytag product nor would I recommend them. Buyer beware - Maytag is not what it used to be! Very disappointing.

Maytag 2000 series front load washer - f you are looking for a front load washer DO NOT buy a Maytag! I purchased a new front load washer dryer set late 2013 and have regretted to washer ever since. Continual electrical problems, door gasket needed replaced almost immediately AND the worst part is that it has ruined over $1000 worth of clothing due to it trapping cloth between the drum and door and wearing holes in them. No matter how I load the clothes or sort them it continues. I have contacted Maytag and was told I have no recourse as the warranty is over. I was very disappointed because I have had Maytag products in the past and had no problems. Please, think twice before buying this washer! It will cost much more than just the ticket price!!!

Bought this Maytag XL washer and dryer in September 2012. In January 2014, the washer stopped working. Service guy came out and said the electronics went out. Then in May 2014, the dryer died. The dryer door latch broke. Would not stay shut. 2 days later, the heating element went out. Again, the service man came out. This service man said that this model is subject to break downs. This Maytag is a piece of junk. I went out and bought a Whirlpool, which I had before. I would never buy a Maytag again. I paid over 2000.00 for this Maytag and it is the worst washer and dryer I have ever had. Apparently, the Maytag repairman needs to get his butt busy. I have the Maytag now on my sunporch, waiting for the junk man to come and get it.

Maytag 18.5 cu ft Bottom Freezer Refrigerator purchased 12/10/12. 1/12/16 the bottom of the freezer had an inch of ice that leaked onto the floor. My plumber chipped away ice and unclogged drains $97.50. 4/19/18) the same $97.50. 5/22/18 an appliance repair business installed a drain kit $148.40. This was his 25th Maytag with the same problem. A whole website has complaints about this problem. I sent a letter to Maytag and they wanted to send out their technician to find out the problem (with a service cost to me). With all these complaints, and a kit to fix it, they already know the problem but refuse to do anything about it. Maytag used to be a reputable company. No more. The customer service said I should have bought an extended warranty. I said a $1400 refrigerator should last longer than 3 years (the first leaking occurrence). I will never buy a Maytag product (nor Whirlpool that makes it).

All I can say is, Wow. My Maytag washer and dryer have never needed anything in 21 years of service. Purchased in 1997 at Lowes in Chambersburg, PA. Both work and look like new! Both are top of the line units. Would buy again!

The washer worked great for the first 6 months, then it didnt dissolve the soap, it wouldnt complete the cycle, and there is a loose bolt like sound when you spin the drum. The load level is not an issue. We have had the serviceman out four times, he has called the tech support each time and they cannot resolve the issue. Maytag said sorry! Unless it does it constantly then they cant help. The control panel has been replaced and the drum has been replaced. So we keep paying the water and sewer bill to rerun the load 1/2/3 times to get it to complete the cycle. This washer was purchased last May, 2011 and they say were stuck with it.

Echoing the sentiments of others on this site, I am deeply disappointed in Maytag brand appliances manufactured by the Whirlpool Corp. When, for the first time in my life, I was able to buy all brand new kitchen appliances, I didnt even consider any other brand but Maytag. This was based on many decades of using Maytag products and watching my mother use them. I come from a big family so our appliances got used hard, and the Maytag brand ones worked year after year, decade after decade with little or no maintenance. To put it quite frankly, my new Maytag products are junk. I could supply a whole laundry list of problems but, in the interest of space, will just tell about the latest. A couple of weeks ago the fake tin foil paint on my oven and burner knobs just started falling off, revealing cheap plastic underneath. When I called Maytag to complain, I was asked how I clean the knobs. I told them that when I clean the stove front I remove the knobs and drop them in warm water with a couple drops of Dawn dishwashing liquid for the few minutes it takes to clean and polish the stove front, and that I had been using this same procedure for 2 years. The rep. hemmed and hawed awhile and then went away to consult her database. When she returned she told me that one is not allowed to soak the knobs per the manual, and therefore she could not offer any help. She then generously offered to transfer me to the parts department, where the rep. informed me that replacements would cost $70 EACH, thats a total of $350 plus shipping for 5 cheap plastic knobs. WOW! What a deal! I tell everyone I meet NOT to buy any Maytag branded product, and to apply extreme skepticism before considering any Whirlpool product. (BTW - the last certified Maytag appliance repairman to come & fix one of the appliances essentially admitted they are junk.) Model #: MGR8775AS SN: R32810432.

I just finished paying off my Maytag Bravos series washer and dryer, and now they are failing! The washer isnt getting dirt out and the dryer power button broke. And its not like I can use some pliers to get the switch to work, its like the part that controls the power just dropped out of existence, leaving me with a knob in my hand that connects to nothing! Of course, the limited warranty only covers the drums, not the little dinky parts that break more easily. I had inherited a set of Maytags and they were well over 20 years old (possibly 30) and they both were powerhouses. But this is terrible! I feel super disappointed that Im going to have to buy a new set after only owning these for 18 months. I know I WONT be buying Maytag ever again, though!

Problems with Maytag dishwasher, purchased at Sears Canada Model MDB7749S is only a couple of years old, and as such is no longer under warranty. This Dishwasher is less than 3 years old! Both the interior and exterior is stainless steel and looks virtually new. Cost of parts and labour to repair amount to more than a new dishwasher--this is unacceptable. Poor design. Little value compared to cost. First issue: bottom rack wheels fall off because the plastic pin holding the plastic wheels on the rack become fall out, leaving no way to hold the wheels onto the rack. Second issue: faulty design of the integrated door handle and control panel on the exterior door face. The control panel pops out of the front cover panel when door is pulled open. With some struggle it can be popped back in.I agree with another reviewer who wrote: The design of the faceplate is defective in that too much force is applied to the faceplate when opening the unit. The handle is integrated in to the faceplate. The plastic used becomes brittle over time and breaks. The panel unit (W10811169) must be replaced in entirety rather than just its housing increasing the cost of repair. To have this failure occur within the first 3 years of use is very premature. I can only assume if I repair the dishwasher I will have the same problem again. I am considering buying a new model that is designed better and comes with a longer warranty on such parts.

Bought our washer dryer set from Sears in the fall of 2010. I had reservations from the start as the machines were new and the salesman was really pushing this set (on sale), with all the customers, even offering extra discounts on these models only, if customers bought that day. Apparently, they had overstock and were trying to sell them all ASAP. That was a warning to me but my husband convinced me that I was being overly suspicious. We had previously owned Maytag machines for 20 years and loved them. So I agreed. Well, I have been cursing that decision ever since. You have to hand wash/prescrub any stain on clothing, even a little make-up like blush or a little mud. Then you have to put up with an inflexible system that wont allow you manual options regarding spins and temperature or times, etc. Its all programmed. Then you put up with clanging spin cycle as it bangs against the wall. Then you pull out very wrinkled and not always cleaned clothes only to begin the most frustrating dryer experience ever. It has a mind of its own. It can actually keep spinning as it keeps adding dry time and the clothes never dry! God help you if you have a regular load. All your clothes will get stuck on the little ledge. They stay there in a heap as the machine spins and spins.The solution? You have to add a bunch of dry towels to create a lot of mass so that it keeps your laundry from getting stuck on the side. Then you have to repeat this several times cause it doesnt dry well. I will never ever shop at Sears and I will never buy Whirlpool or Maytag again. I am now saving to buy another set.

I purchased the gas stove in June of 2012 from Home Depot, along with a Maytag microwave (Model MGR7662WB4). Home Depot installed both items. After trying to reach into the microwave about the stove, the knob would turn itself on with me brushing up against it. This happened several times, and one time the flame shot up and I almost got burned. The last time it happened, I did not realize that the knob was turned very slightly and gas was coming out of the burner for several hours. If it were not for a friend stopping over, I would not have considered the odor being from the stove. I assumed that the drains were probably backed up and started to add cleaners to the toilet bowls. I had to open the windows for several hours to get the smell out. So I called customer service 2 times. The first person said I would have to pay for the call if the problem was not Maytag and I said, “Forget it.” Then I went into Home Depot and the salesperson in there gave me another number to call for service. They came last Friday and said that he had seen at least 10-15 calls about this and since the unit was working as designed and no recalls, there was nothing they could do. “Just wait and see if a recall would be put into place and I would be on the list to fix it. In the meantime just keep the knobs off (which I was doing already out of fear).” My sister just bought a Whirlpool gas range this summer as well and asked if I could try her knob and it worked perfectly. Again I called CS and was told they could not send me those at no charge and that it would cancel out the warranty. So I asked her what I have to do before I or someone else gets injured and she said that until there was a recall, there was nothing they could do. I told her I was going to contact Consumer Report as well as Pam Zekman on Channel 2 news in Chicago. End of story; I still have the problem and no knobs on the new stove. Anything you can do to help please contact me, and thank you in advance.

Major issues with the Aqua Lift Range. Takes forever to preheat the oven, 15-20 minutes to reach 375 f- 400 f. Aqua clean cycle not efficient and does not clean at all. The stove top is impossible to select and keep the heat consistent. When adjusting the heat up or down when you slightly move the dial it overreacts. When moved the heat sways may more than selected. The fridge works well but the bottom drawer is way too flimsy and it wont last a long time as it will crack. This is our first purchase of Maytag appliances and it will be our last. Our old 10-year-old stove worked much better than this one. Sincerely, Russell ** & Linda **, e-mail= **

I purchased a new Maytag top freezer refrigerator. From the time it was delivered the freezer temp never went below 10 degrees. It ran between 10 and 20 degrees. Ice cream was soupy, bread did not freeze. I called Good Deals Appliance in Fort Myers, FL where I bought the refrigerator 3 days after delivery to report the freezer problem. They sent a service tech out who looked at it and said the model I bought has no freezer control so it could not be fixed. The store I bought it from said Whirlpool, who owns Maytag, said 10 degrees is acceptable for the model I bought so there was nothing the store or Whirlpool would do to replace it. I called Whirlpool numerous times, was on hold for over half an hour each time and was told 10 degree freezer temp is acceptable. After considerable arguing, they agreed to send a second repair person who came out and said the freezer temperature problem could not be fixed. After numerous additional calls, a complaint to the BBB and a stop payment on my Visa, Whirlpool sent a third service person who said it could not be repaired. I began the round of phone calls to Whirlpool again as well as to the Good Deals salesman who has been as useless as possible, continually saying it is our problem to deal with Whirlpool. The BBB contacted me and then Good Deals who said Whirlpool has agreed to replace the refrigerator but I have to contact Whirlpool. I have called Whirlpool, waited forever on hold, and left three messages and no one has returned my call. Whirlpool should not call what they do customer service. They are rude and argumentative and make it very difficult for customers to contact them and even more difficult to get a defective appliance replaced. DONT EVEN CONSIDER BUYING WHIRLPOOL OR MAYTAG APPLIANCES?

Maytag Bravos MCT washer not good - Owned this since June 2017. This thing has never worked properly. Every time after a cycle is complete we have to wring the soaked clothes by hand. Even after doing this the drying time ends up being double what it should be because the clothes are so wet. Not only time wasted on hand wringing clothes but also wasted energy in drying them afterwards. Also this thing is supposed to auto-detect how much water it should use but half of the time it uses too little water and doesn’t actually wash all of the clothes. Some clothes stay totally dry when this happens.

Thanks for the other reviews about the control panel problems... I too have the same issue with the short circuit. My Maytag dishwasher mdb7749sam1 was installed in January 2013. I spent an hour on the phone and the chat... HERES THE SOLUTION: When I told them the machine started in the middle of the night on its own, it became a safety issue. I have all the same problems as everyone else, flashing lights, the washer does not properly respond to the input from the control panel... I was told that even though it was out of warranty, as a gesture of goodwill Maytag is sending out an authorized repair service to fix whatever is wrong at no cost to me at all... Tells me that there really is an underlying issue. Anyway best of luck to anyone else in the same boat. I rated them as a 3 - not happy that this machine failed and I wont buy another, but they seemed to jump on fixing it...

Worst washer ever. My clothes I have to wash a few times before they all get wet. Not a good washer at all. Has all the bells and whistles. Lets me know when the washer is done or its unbalanced... my washer is crap. Ive had it maybe a year now. I now have to buy another one. Why? Because this one sucks literally... its Maytag commercial technology.

I purchased a matching set Maytag washer & dryer June 2013. Sept 2013 the drum went out - 4 weeks for that repair. March 2014 the electric panel went out. Took about 10 phone calls with hold waits of 30 to 70 minutes and 4 months, to find out the replacement part is no longer available and the washer is discontinued. To get a new matching set, I had to pay for a new dryer and they will give me a free washer. I have to give both washer and dryer back - I paid for 2 dryers. 6 month later and more phone calls, no washer and no one will return my calls. The dryer I paid for is at the appliance store waiting on the new washer. We consumers have nowhere to go. I have heard so many similar situations. Where are we to go? Who are we to call?

I purchased a Maytag MDB7749AWM model dishwasher in March of 2012 for approximately $600. Fifteen months later, the control panel has gone out on it. From what I understand, this problem happens so often that its not even worth repairing this dishwasher.

I bought this range (Gemini Double gas range) in 2010 but was not installed in my house until 2011 due to time delays in kitchen re-model. I paid $1310.00. It was serviced 3 times once under warranty. About a year ago the igniter went in one of the ovens for the second time and one of the stove burners wouldnt light. Since the other oven and 3 other burners worked we didnt call for repair, then a second burner stopped working and we called our Maytag dealer. 2 different service techs came one with more experience and both said the same thing the stove wasnt worth fixing due to cost of parts. One of the problems was the screws in the burners couldnt be removed due to rust and deterioration of the screws. They would break and cost other components also to be needed. So after 7 years of use and already having repairs done I have to buy a new stove. It will not be a Maytag. I also bought a top of the line Maytag dishwasher and one month past the 5 year warranty the electronic panel burned out. After calling Maytag and complaining they did agree to pay for the part close to $300 but I still paid for labor. When I looked at reviews for the oven before purchasing they werent too good but wanted a double oven at the time and always had good luck with Maytag in the past. I thought buying a higher priced model would be better quality. Not so. After calling Maytag today the best they could offer was to buy an extended warranty for $380, I declined. My advice - Listen to the reviews. The Maytag repairman isnt sitting around idly anymore!

This set of Maytag washer/dryer are nearly nineteen years old now and are still workhorses! They keep getting the job done time and time again! Absolutely no complaints. Absolutely and completely amazing!

Purchase brand new range a couple of months ago. Self-clean oven does NOT self-clean and leaves weird, flakes of something that stick to oven floor. Burners are inconsistent and difficult to control heat level. Take forever to get warm, and then either boil over or wont get warm enough. Purchased this with inheritance from my mother - how sad! Always had such faith in Maytag.

Bought a Maytag refrigerator from Home Depot about 2 years ago. Like everyone else we are having leaking problems from the freezer drawers. I wonder if anyone has had it repaired and whether it was repaired

I purchased the Bravos X washer approximately 13 mos ago. Washer was noisy and has deteriorated since installation. I questioned the ability of a non agitator appliance getting close clean but was assured it would. Not the best if clothes are just moving against clothes. The machine had a difficult time in between adjusting to wash balancing a 3x event upon starting. It leaked intermittently during spin cycles and stopped due to unbalanced loads, sometimes refilling and stopping again. Now it wont spin at all, circuit board problems! This is my first and last Maytag. The company will most likely not balance/compensate on the purchase price (like the Bravos X) because it is beyond the 12 mos warranty.

We bought the washer less than a year ago. The washer became off balance with an average load of jeans. The washer shook so violently that it cut our floor, busted our wall, and broke itself. Water covered our floor! We have now been over a month with no washing machine (still paying on it, by the way). We have had to pay to get our clothes washed in the last month = EXPENSIVE! The repair company has been out to our home twice, broken high-quality tools trying to repair the machine, and told by their higher-ups that the washer can still be repaired. Customer service only tells us that we have a repair warranty and the first repair has no time limit.

I bought a Maytag washer January 2016. We recently had a issue with it so I logged onto the Maytag website and found a service provider to come see what was wrong. I had to pay a $100 fee for them to come out and look at it. I was told that the transition went bad. The parts were under warranty however I would have to pay for labor, which would be $325. Called Maytag and was told because I did not purchase an extended warranty there was nothing they could do about the labor. I can buy a new washer for $500 why would I spend $325 to fix? Already lost a $100 for them to come out to tell me what was wrong. Completely not right. A washer should last more then 4 years! Do not buy any Maytag produces. Will not last!

I purchased a Maytag Bravos washer and dryer combo 2.5 years ago. Six months in, I noticed that the washer would always stop halfway through the cycle. We had a repairman come out because it was under warranty and he said it just had to be reset. I then started to become weary of the product. The washer, that is larger than most, is still a problem today. The dryer, the last couple of months, has not dried clothes completely. Today the dryer just stopped. Maytag will rip you off when called for service because the warranty is expired. I have owned old dryers for several years and I am so disappointed with the Maytag product that I will make sure that anyone I know thinking about purchasing a Maytag will buy another brand. The worst washer and dryer I have ever owned.

I had bought Maytag Dishwasher MDBH979AWW3 in Sep. 2009. Oct 2011, the dishwasher stopped working and the control panel had to be replaced, few days later, it stopped working again and the Thermal fuse had to be replaced. Now two months later, it stopped working again. Till this point, Ive spent a lot of money on the repairs and I wish I had used that money to buy a new dishwasher. Looks like not just the Maytag dishwashers are faulty, but even the parts they have are faulty. I will not recommend any Maytag products to anyone.

Maytag Centennial Model MVWC400XW4 - Washer is leaking from the bottom and making loud noises when spinning. Called the Maytag repairman and right away said that the bearings were bad. He said it was a 800 dollar repair for this 500 dollar machine. The service call cost me $97. I immediately went out and bought a GE machine. I wont buy another Maytag.

I bought a Maytag dishwasher in January 2013. Three months later, the cheap plastic latch on the door malfunctioned. I waited 3 weeks for the repairmen to get the part in. Is there a sense of urgency anymore? If I owed Maytag money, I bet there would be a real sense of urgency on their part. Next time it will be an LG dishwasher.

I love my Maytag. It does a good job, however, it takes almost an hour to run one load. Also, if you have a heavy load, it doesn’t spin long enough so your clothes are dripping when you take them out.

We purchased a Maytag Bravos washer & dryer in September 2012 and 2 1/2 years later March 2015, no heat. We called a repairman and he said heat element went out. When researching this problem online I was shocked how many people had the same problem as we have. It cost over $300 to fix and I am concerned that it will just break again and again after reading these reviews. I think that a class action lawsuit may be needed so that this unfortunate situation does not continue to happen to other consumers.

OK, LAWYERS -- Where are you?!! You have a lot of very unhappy people who feel they have been justifiably TAKEN! Whirlpool needs to replace these refrigerators with another brand! We bought same bottom freezer Maytag refrigerator in 2010. Luckily, which we dont usually do, we purchased a five year warranty plan. Within six months we noticed the rubber seal on our refrigerator on the french door part was turning yellow and then getting darker. We feared something was burning the rubber. A Maytag repairman looked at it, called Whirlpool, told them that there werent enough parts to fix this refrigerator. Whirlpool asked him what they should do and he told him it should be taken out on the front lawn and burned (yeah for that repairman)!! Whirlpool agreed to replace the refrigerator with one, very similar but a new model #. Thank heavens, after our insistence, the warranty was extended to the new one. Now after about three years, we are having the same problems that all of you are having with the next one.. Our Home Owners insurance adjuster just gave us a settlement to have all the ceramic tiles removed, which are cracked in almost two dozen places, and whole floor replaced (minus our $1,000 deductible). The floor was put in new three years ago. The refrigerator repairman is next to come out. From what I have just read about all the complaints on this refrigerator, NOTHING is going to fix this problem short of replacing it at our expense. My advise to everyone --- FIGHT THIS. Write to Whirlpool (not Maytag -- Whirlpool owns it), and blast them over and over with letters and complaints and threats of lawsuits. Why should we be taken for that amount of money while Whirlpool does nothing but keep it. A class action suit is badly needed. Big corporations should not be able to take people over like this and get away with it. If it takes a lawyer willing to take on a class action suit, this is it! In the meantime, bombard Whirlpool with letters and dont stop! It takes persistence, but in the end -- most of the time, we will prevail. Big companies hope we will give up and go away. They count on it. Dont let them win!!! I have had a Maytag washer and dryer for twenty years with no problems. Problem is that Maytag doesnt exist anymore -- who is making this....?

Was coerced into purchasing this fridge three years ago. Told how Maytag is the highest quality fridge etc. From day one it was noisy and seemed to be running half the time. I had asked for a quieter fridge, partially why I paid $2000 for it. Now there is something wrong with it. Not sure what yet. But for $2000 it should not be failing three years later. My Samsung was quieter, 1/3 of the price and lasted at least 8 years. Thought about calling customer service but read too many bad experiences here in regard to that. Will never use Maytag again.

We have had our Maytag double oven for about 5 years. 18 months ago two of the burner knobs froze off. You cannot turn them. We had oven repaired - they replaced part WPW 10204705 - it cost us approx. $400 to repair. Here we are today and ANOTHER burner know has frozen in the off position. I will have to pay again to have this repaired. We are super disappointed with this over and with Maytag. We would never purchase from them again.

Maytag dishwasher 5/3/2010 model MDB6709AWQ1. 12/20, 2015 it is dead, $69.00 service call. Failed user interface and main PCB parts estimate with labor $449.46. Called Maytag Co. We would pay the labor $139.00. MAYBE they pay the parts.

French Door Maytag MFI2569VEW10 faulty in many ways. We bought our refrigerator 7 years ago. After 2 years the freezer door handle fell off; after 4 years the right front door gasket began to tear (normal usage); after 7 years, it no longer dispenses ice or water. We now have mildew/mold growing around the edges of the door because there is no longer a good seal. Constant cleaning. Additionally, we are spending more $ to keep the refrigerator at the proper temperature because the seal is broken. To repair these items is almost $700 including shipping and tax. This does not include the cost of labor. So after 7 short years, we have a hunk of junk that does not work properly. I am shocked that Maytag sells such an inferior product and we are left holding the bag. Do not buy Maytag. Additionally, our Maytag microwave broke after 5 years. DO NOT BUY!!! Buyer beware!

Refrigerator failed in less than 7 years. In August 2005, I purchased a new Maytag side-by-side refrigerator to match the Maytag appliances (stove, microwave and dishwasher) in the new house provided by builder. In October 2011, I called a repairman because of noise. The relay switch was replaced for $179. Now, I am told the compressor and defrost circuit board need to be replaced for over $700. I will never buy another Maytag appliance or Whirlpool. They make and sell crap and dont stand behind their crappy products.

Wish there was some way to secure all dishwasher under the cabinets better. It tips forward slightly, but gets caught on counter top, so it won’t fall over. The dishwasher itself is truly amazing. I love the stainless steel inside. I ensure I use the dishwasher cleaner on hottest cycle once a month. I have no odors. Both racks hold up well and the silverware tray has never given me any problems. I even like the thin little third top rack, which is where I lay my larger flat knives or spatula. As long as I use the finish dishwasher cleaner, the dishes come out sparkling. And a few times I have forgotten to fill the finish container, the dishes still sparkle. My teenagers do the dishes a few times a week. They don’t wash them off ahead of time. On occasion I have to pick a few pieces of corn or food out of the bottom, but the dishes still sparkle and the leftover food caught on the drain, well it looks clean enough to eat. I would definitely buy it again.

I purchased a Maytag Bravo Washer in October of 2011, I had a repair man come to check it since the spin cycle sounds like a jet is revving its engines in the laundry room. He told me that the repair cost is $493.50 to replace the transmission. The machine also has problems with the circuit board. The lid lock goes on and off and on and off so you cannot run the machine. Speaking to Maytag they just kept saying your warranty is over and we dont offer any assistance on the repairs. The machine cost $530.00 in 2011 and they think its reasonable to have repairs more than the cost of a new washer. They said they had no complaints on the model. My repairman advised not to buy Bravo, Cabrio or Calypso models since they all have the same problem with the transmission and electronics. I think they should at least pay for the parts, the transmission is $300. And we didnt even price the electronic part of repair.

I purchased an LG (white) washer last year, but my husband upgraded all appliances to stainless, including Maytag washer and dryer. The washer does not fill with enough water to cover the clothes. It barely agitates them to wash. Some clothes even come out with dry spots on them at times! They smell and are still dirty when done. I have tried every setting hoping that was the issue. Normal, power wash, none work any better! Had to resort to the soak function which does not add fabric softener or drain the water completely. Thankfully I didnt sell or get rid of the LG. Putting the LG back in asap. Nevermind the mixed color finishes of white and stainless between the washer and dryer. Clean clothes most important! Piece of garbage and complete rip off!

The performance of the refrigerator is disappointing. It was difficult to find someone to repair it when the freezer fan motor went out. It makes noise, shelf space is insufficient. Temperature mechanism often doesnt work properly.

We have had our washer and dryer almost 18 years and just recently spent less than $280 to get the washer going again. The dryer we haven’t had serviced yet. Great quality. So worth it. Our Maytag appliances are used frequently and keep giving out the best performance.

Got woken up to the sound of my refrigerator ice lid flapping. Boy is it loud! Called Maytag and found out it was a recall so they will fix. They set up for someone to come out to fix the following week. That was a flop because they did not have the part. I waited 4 hours for someone to show to find out that Maytag scheduled the appointment for nothing - not only did they NOT have the part but they did not have a clue as to when it will come in. Time is valuable! Here we are 5 weeks later and my refrigerator is still flapping and loud. Has been calling Maytag for them to say that the part has been expedited. Well it has been expedited for more than 3 weeks now! Today they say that it will be another month before the part comes in! Not Good! This is such an inconvenience and Ive lost a lot of sleep over this flapping noise. Its an embarrassment when guests come over to our home! Tired of it!

This washer is awful. We had repair guy out within year one 3 times. Changed the door gasket because it was a known problem. That did not fix problems. We have to drain and clean out hard to reach filter monthly, socks get caught in drain filter constantly. Horrible, horrible, horrible. Hate it.

This washing machine is garbage! We paid almost 1000$ for it and it damaged most of our clothes. We believe this washer was released from Maytag with a functional problem. Because it does not drain the water and soap properly, therefore it leaves white stains on the clothes after it is done. Please see in the picture. After recommendation from Lowes we clean washed with Affresh for many times, it did not fix the issue! We called Maytag customer warranty service. They sent a technician and his solution did not solve our problem. We called them again and they said if they send a technician again they might charge us 130$. We think Maytag warranty is a waste of time and energy. They are useless. We will never ever buy anything from Maytag.

3 year old Maytag Washer model MVWX600XW broke. Paid $345.55 for extended warranty. I had to wait 10 days for Appliances Unlimited to fix the washer in Sept. then the washer broke again in November needing 3 more parts including a motor. It took almost 2 weeks for Appliances Unlimited to come to the house, then I have to wait 5 weeks for a new motor to be in stock.

Our dishwasher developed a smell. We do regular maintenance and care of this dishwasher. Come to discover the entire thing is full of mold. Customer service is rude and expects us to wait two weeks for a service person to come out. Will not use the dishwasher because it is probably making our family sick. I have never experienced customer service like this. DO NOT BUY DISHWASHERS FROM THEM. They don’t care the product is defective and they don’t care about their customers or their safety.

Maytag Washer 2016 HE top loader. This washer is horrible to use. I hate everything about it. After your clothes are put into the drum and you close lid to start here is what happens EVEN though I select deep water: it puts small amount of water in and then it agitates the whole big load. This is so stupid! Can you imagine a large load of your clothes agitating with a very small amount of water in the drum?So to get around that problem, you have to push pause button and shut the lid after your soap, softener and then listen until that first amount of water fills and agitates, then you have to push pause and quickly put in your clothes. Then you shut the lid and again push the start button so it will fill with more water. Then if youre lucky in at least an hour your load is finally finished. I hate this washer. My boyfriend bought it and I asked him several times to PLEASE return it. He didnt so now were stuck with it for God knows how long. The one good thing about this is I will know to never buy one of these for my house.

WOW, I cant believe a group of educated professionals made, tested, and approved such a washing machine. What a piece of crap. I could put my clothes in a bathtub and let the kids jump up and down on them and they would come out cleaner. I would love to have a heart to heart talk with the engineers who designed this, to ask, What were you thinking. What a waste of money, and a once good company, that will soon be going out of business.

I paid over $600.00 for a new maytag washing machine two years ago. It quit working a few days ago and the man said itll cost over $400.00 to fix it. Why do you people build this type of junk? I would like to hear from someone on this and why I had to pay $300.00 a year for a washer that is totally worthless now??????? ** please contact me. This is crazy to buy this washer and it only last two years.

This washer is only two years old and does the wash for 2 people. The control board has broken down and the lid lock did too. Of course the warranty had just expired, so there is no help from the maker, Whirlpool. Save yourself a big loss and dont buy these brands. Mine is going to the dump where it belongs. Thats $500 down the drain. Do yourself a favor and get a Speed Queen.

I bought a Maytag Centennial Top Loading washer 2-1/2 years ago. Its worked very well, but has started to roar so loud on high-speed spin that you have to leave that side of the house to be heard. The factory technician determined that it had a bad gearbox and that it wasnt anything I had done that caused it. He told me it was going to cost more for parts & labor than the machine was worth. I called Maytag and was told they wouldnt help me because it was after the one-year warranty. When I asked for a supervisor, he offered to pay for the parts, but not the service. Thats kind of like Chevy offering to pay for the defective engine part, but not the installation. I have never bought a major appliance (or even a hair dryer) where I thought 3 years was a reasonable life expectancy. Lifelong Maytag Customer has left the building.

I am retired and have always had dogs in my life. My recent purchase of a new Maytag top loading washer has been very frustrating. There is barely enough water to measure in an oversize tub. The placard on the lid, and in the owner manual clearly show three levels of water. Each load takes twice the time as I am used to with my older Kenmore washer. I am forced to cut my loads in two or three, and use more water and energy to do a job that used to take less than half the time, water and electricity. I have had warranty repair to replace the control board twice, but nothing has changed. The repair techs both said there is one program on new washers, the knobs and settings do nothing, and recommended I get used to it. They explained the EPA is responsible for all changes to Protect consumers from harm. WHAT???I wish I had never bought this unit - if I could get my Kenmore back I would, in a hot minute! What a waste of a large tub to properly wash pet bedding and bedspreads/pillows, when there is only 3-4 inches of water! I wasted an entire paycheck, when I could have gotten my other unit repaired or rebuilt. I am seriously frustrated, I am searching for an older washer unit to get back to doing my laundry without being forced into a laundromat for pet bedding and larger items!!!

Sounds wonderful. Thats what I thought when I let my son have my 20-year-old, still running older washer. I wanted a new one. It worked good for 3 years and then one night I went to throw the clothes in the dryer and its full of water. After the last rinse and spin, it filled again and stopped. So I tried it on every cycle and got the same results. I thought, No problem. We have a great, honest repairman. Ill call him the next day and hell fix it. When I called and told him what type of washer it was, he was surprised it was working at all. Seems they had a problem with water leaking into the transmission. Apparently, I was lucky that mine had worked for as long as it did. Like I said, Im lucky to have an honest repairman. He told me he could charge me to put in a new timer and solve that problem, but I shouldnt waste my money since it is just a matter of time before it goes bad. Seems they were all bad and Maytag never made good on them. Told me the smartest thing to do would just to go ahead, bite the bullet and get another. It will be here Tuesday morning. Hopefully, this will be the last one I have to buy (keeping my fingers crossed since I had hoped the Maytag was going to be the last). My old machine is still running great for my son. Over 30 years my repairman has had to fix quite a few things for me - ice makers, dishwashers and even a timer on my old washer. Thank goodness he was honest enough to not fix my washer. I dont know if there are even any Maytag products around now, but if there are, they will never get my business. I spent a fortune on a machine that should have lasted the rest of my life. Ive had childs toys that lasted longer. My advice is do not buy Maytag.

My new dishwasher had a defective board and worked erratically. Shortly after the warranty was up it stopped working completely. I contact both Maytag service and Home Depot on several occasions with no satisfaction. This a well known defect. Apparently the board replacement and service would cost in the range of $250-300. Too much for me as a senior on fixed income to justify. No dishwasher for almost a year. I then read an article indicating there was a class action settlement in California on the same make and model. I called Maytag again and after spending 2.5 hours on the phone I finally reach a person who sent out a service repair person. This person showed me a memo confirming the problem with the board. No recall but... if a customer is persistent they will give you the board. Finally new board installed at no charge.

Maytag french door 2015 refrigerator. Not happy at all. Freezer gets rim frost on sides of pull drawers and the smell is like dirty socks when motor is running! The whole kitchen stinks???

We went to Home Depot and bought a Maytag front load dishwasher and dryer and microwave 3-1/2 years ago. The washer and dryer were put in right away. The dishwasher and microwave stayed in their box for another year due to us remodelling the house room by room and the kitchen wasn’t done for a year. We put the appliances in and the dishwasher panel went out in October 2011. The washer in April 2012 started having a failure 8 when it gets to the last spin and rinse in which takes a lot of shuffling clothes to get it to finish its cycle. Then last night, May 14th, 2012, the microwave caught fire and all I was doing was brew tea in a glass Pyrex measuring cup not to mention the fan didnt work from day one. The whole house was full of smoke and it melted the plastic. So the most I got out of 3 of these products is 3 years at the most. This is very sad that we spent this much money and it lasted less than 5 years. I am writing this to warn consumers not to buy Maytag appliances. They should last longer than 3 years and are not cheap to buy. This makes me very angry and I hope someone takes this seriously and work on the problems before someone burns up due to these appliances catching fire. Our dishwasher had a recall shortly after we installed it due to the element catching fire and we had your repair man replace it.