My washing machine was noisy from the start. We had recently purchased a new fridge and were told when we questioned its noise thats just the way they are. So we didnt question the noisy washer as we should have. The noise got louder as time went on and at the 18 month mark, it was so bad, we had someone look at it. The washer had never cleaned as well as expected, but again, we were too busy to follow up. The repairman advised that the bearing and tub needed to be replaced! Augh! $450 for parts $300 for labour! I contacted Maytag/Whirlpool and was advised they would go good for the parts, I would have to pay labour. Not being terribly impressed, did a bit of research and was told it was worth fixing. As it was technically out of warranty, I was lucky to have them pay for parts. Took 6 weeks to get part. In that time, had questions about delay, etc... at one point was yelled at on the phone by Melissa from Whirlpool as I asked to speak to a supervisor. So fun :( First part comes and it is defective, luckily there was another one in Vancouver, so only an additional 4 day wait. My machine is now fixed. It is extremely quiet and cleans very well. Suffice to say, it was defective from the start. So, Ive gotten to pay an extra $300 over retail to have a working machine! Lucky me! Repairman also advised that he recommends everyone to purchase the additional 5 year warranty as the manufacturers are now only making machines with a 7 year life expectancy and I was VERY lucky in the beginning to get someone to even talk to me after the 1 year mark.

Maytag microwave MMV4205BAB - I purchased this microwave in 2007. By 2009, the whole inside was peeling down to the metal. Under the glass plate, the bottom is all rusted. Ive called customer service every year since 2009 and they say the same thing. No extended warranty, nothing they can do. They acknowledged that this was not normal, but they did nothing! Do not buy anything from Maytag. If you do, buy all of the expensive warranties or you will be sorry like I am.

We bought this stove in 2014. One knob got stuck while my teenager was cooking food on the gas stove. He called me at work worried because he couldnt turn it off. My husband left work right away to go home. We thought it was just a bad plastic knob. Now a second knob is stuck in the on low position. There is a third knob that feels hard to turn. That will be 3 burners. This is ridiculous. Its a safety hazard. We consumers have to worry if the house will burn down, get CO2 in the air, and if our family and children are safe. We thought Maytag was a good appliance. I will not buy another Maytag. They should recall this stove top/oven. I have read so many of the same complaint on this website as well as online in general. I cant believe they continue to sell this with this much of a safety issue. Please take it off the market.

We purchased this oven (MER8880AS) as part of a package during remodeling in 2012. I was particularly interested in the bridge element, and in fact, its about the only part of the range Im satisfied with. Our first problem arose when we began using the range in 2013, and I got cut on a sharp edge while opening the storage drawer under the range. We contacted customer service, got a prompt and concerned response, and shortly after, a visit from a technician. Heres where it started to go south: the technician insisted that design as fine and that we were reaching too far into the drawer to open it. He left, saying basically not a Maytag problem and the customer service agent, who had promised to call after the visit, never responded to our calls. Fortunately, we have a good hardware store nearby and my husband and their staff came up with a solution.Burners and oven work okay, though with slower response time than other electric ranges Ive used. Convection feature seems ineffective on this range - I hardly use it anymore, though do use it all the time on my other range. The absolutely worst feature of this range is the Aqua Lift Cleaning System. This is a hoax by Maytag, marketed under the guise of an environmentally friendly system. It does not work, and pre-cleaning doesnt improve the outcome as only portions of oven that are clean are the ones pre-cleaned! If you like to cook and bake, do not buy this range!! Based on this experience, I will never buy another Maytag product, and though Im of the school that expects major appliances to last a long time, I can hardly wait to replace this range!

Is there any place to give a zero to this Maytag Front Load Washing Machine Model MHW5500FW1 and if there is a class action lawsuit please include us! We have owned other Maytag Washing Machines and never experienced such an epic failure as we have with this washing machine! We were so excited when we purchased our new Maytag washer/dryer set in March of 2018 we even remodeled our pantry/laundry room to accommodate them! As the chief operator of the washing machine, I have literally cried at what a mistake weve made! We have no complaint of the Maytag dryer. Let me describe my new normal procedure for laundering a load of clothes. First, load the washer with clothes then press power/cancel then press rapid wash let the clothes get HOPEFULLY saturated with water then hit hold to start and then hit power/cancel this shuts off the washing machine. I then press power/cancel again and select normal and the water empties out of the washing machine from the prior load and then starts to refill, if the add a garment light comes on (when it wants too) and no I dont change any pre-set settings I am able to add extra water with a pitcher, if this procedure works I let the washer run its 1-hour and 48-minute cycle. If not, I have to start over again because the add garment light wouldnt come on to allow the door to unlock. After the clothes are finished I again press power/cancel then hit rapid wash put my fabric softener in the dispenser press hold to start and let it run its 36-minute cycle making sure my clothes are rinsed appropriately and not stiff because of the lack of water. I neglected to say that when Ive tried tricking the washer and think I am able to add extra water, if Ive added too much the sensing kicks in and the washing machine drains all the water out on its own and refills with the little water it allows! Which is maddening! I throw up my hands and sit down and cry!!! I have contacted Maytag/Whirlpool complaining about the lack of water and their wacky water sensor! I asked them how can you conserve water and electricity when you have to wash your clothes over and over with long wash cycles? This doesnt make sense! My white clothes are now dingy and stiff as well as the colored. Maytag says you can use powdered detergents if its HE High Efficiency powdered detergents, but thats not true. The detergent doesnt dissolve and ends up on the clothes at the end of the long wash cycle because of the lack of water! From the beginning I adjusted the amount of powdered detergent for the front load washer and have to dissolve it in hot water prior to washing and hopefully am able to add it to the clothes if the add a garment will let me! I have now resorted to extra cycles to rinse out any remaining detergent hoping my clothes will be soft and fresh smelling. I had planned to replace my old Maytag agitator washing machine with this piece of junk front loader, fortunately we kept our old washing machine as a back up!

We purchased a MAYTAG refrigerator when we recently built our present home. This refrigerator has been a nightmare! Ice forms in the bottom freezer and then constantly melts out of the bottom of the appliance all over the floor. Weve had a number of service calls with no real effect. The computerized function that sets functions do not work well and often shut down the appliance with little clear way to start it up again. The ice maker/dispenser often clogs up or will not produce ice. Weve had it! We broke down today and spent the money on a new GE refrigerator. My very strong advice is DONT BUY A MAYTAG refrigerator with the freezer on the bottom!

This review is for a Maytag dishwasher. I do not know the Make/Model. It did a very poor job of washing the dishes. It may have been the city water, but no matter what I put into the machine to keep the dishes from being cloudy it never worked. It became disabled about a year after we moved in, and it was only about 6 years old. However, there were two families before me that used it and I have no idea how they used it. It was the first and last Maytag dishwasher I will ever use.

I purchased this five-burner gas stove two years ago. I have this stove repaired three times. The first and second problem with the stove is when I turned on the oven, it would never click on. This was a month after I purchased the stove. They sent someone over to correct the problem and that did not work. The third time someone came. He changed something in the oven and it started to work. After that, I continue to have trouble with the oven. When I have the top eyes on, the oven will not work. When I only turn on the oven, it will go to 350 only. It will cook for an half hour and then cut off. I smell gas in my house and my food is smelling like gas. I have stop using the oven. I did not purchase a stove to not use the oven. This is totally ridiculous!!! I am tired of this situation. Maytag needs to recall these ovens, so I can purchase an oven that works. I have thrown food away because it smells like gas - because the oven will cut off in the middle of cooking. I am very tired of this situation and when you call Maytag, their customer service is terrible. I will never buy Maytags products again. Please help.

I have a front loader dryer, model number MAH5500BWW, serial number A9147862ec. All of a sudden, I found water on the floor and after opening up the front door, I see where around the part that sticks of on the inside of the door, there is a big piece of plastic that has broken off and cracked all the way across the bottom of the door and is missing. It is allowing the water to leak down the front of the bottom of the washer and onto the floor.

I purchased a Maytag Bravo xl washer & dryer for $1600 in May 2017. Sunday, the user interface panel went out in the washer. After an $85 diagnostic visit, we were told it would be $500 to repair and take an additional 5 days. My husband is recovering from major knee surgery so I was short on choices. I elected to purchase a new speed queen and will never purchase Maytag again. The 10 yr warranty tag on the front is useless!

I had one set of Maytag washer and dryer and I loved it. I bought another set and hate it. The washer smells and has been fixed a couple of times and the dryer is bad. I had to have a drum replaced because of one of the bars inside. I paid for the insurance but the bar was considered cosmetic. It has fallen off again after about 2 years and Im sick of it. I will never buy another Maytag again. Repairman, of course, had to order the drum and then I had to take another day off work to be here when it was delivered and one more to wait for him to come. I am so unhappy with this brand - never again.

Maytag Bravos XL Washer and Dryer. How exciting to get a new washer/dryer!! Im a savvy bargain and quality shopper, but I really messed up here. A little over a year ago, we moved from IL back to TX and I got to buy a new washer AND dryer at the same time (a rarity). I went and looked at SO many washers/dryers and decided on the Maytag Bravos XL because a friend said she loved hers. It had a deep water wash and bedding cycle (for our blankets, comforters, sleeping bags, etc), and I thought that I could throw that wayward sock in after I started the load (unlike our previous front load washer).Where do I begin with the complaints? (And Im NOT a complainer - never filled out a review in my life). This is what I sent to Maytag: 1) Im 55 tall and can barely reach the items at the bottom of the drum, along with the lid falling on my head when Im trying to do so. 2) Forget throwing in the wayward sock - it must finish the cycle its in before it will let you unlock the lid (Where did locked lids come from anyway? Is that how those missing socks are disappearing - escaping out of unlocked lids? What are we trying to keep in or who are we trying to keep out of the machine? Doors you lock - not washing machines! I dont get it!).3) Even the deep water/bedding wash cycle does not do the job. Using the exact recommended measurement of HE liquid soap does not get the items clean. What a chore to take something out and have white detergent lines all over it and have to wipe it down with a wet cloth. Sure, I could then do a rinse and spin cycle, but since it doesnt add enough water, it doesnt come out much better. The machine senses by weight how much water to use. I am positive that every energy efficient machine is now programmed to add exactly 4 cups of water per load (regardless if its a comforter or one pair of jeans).4) Supposedly, we are saving so much water usage, but energy efficient is a misnomer - it takes me twice as long to do laundry now. The time factors are ridiculous. There are no quick cycles on this machine. If I have a load of delicate tops that just need a quick wash and rinse before I hang them out (I was not out baling hay in them, so its not like they are filthy dirty. In Texas, its the sweat that you are trying to eliminate), the least amount of time I can find on a cycle is 45 minutes. I might as well hand wash them all and be done in 5 minutes. But, that was the point of the washing machine - to do the work for me! And forget the deep water wash cycle of 58 minutes, plus the added rinse and spin cycle (to try and remove the white soap line). Its now taken one and one-half hours to try and clean/refresh a barely soiled comforter.5) The spin cycle is SO efficient, that I have items come out totally dry many times in certain spots. Im washing a comforter right now and I can guarantee you that when I remove it from the washer, there will be an entire section that looks like it never even got wet. Im no engineer, but after watching through the see-through lid, the agitation is not working well enough to get to every section.6) I havent seen a soap bubble or suds yet. You are told to use such a small amount of detergent, Im not sure how anything actually gets clean. The clothes are sprinkled with water, agitated a small amount, spun until they are almost dry and voila - the same dirty clothes come out! 7) The dryer has now ruined 2 of my bras as the hooks get caught in the mesh panel at the back. It literally melted part of the bra! I tried hooking them together before I threw them in there, but now have to put them in a lingerie bag to keep them from being mauled and mutilated. I have NEVER in 37 years of marriage and washing had that happen before.8) I literally could not get my dryer to turn on and a repairman had to come out to the house to show me the amount of pressure I had to use in one finger to start the dryer. I had almost taken a hammer to it before he arrived. Can you imagine pressing the start button on anything - the dishwasher, a hair dryer, a TV remote control, and it not turning on? And all because you pressed too hard or too light? This computer age and electronic panels are killing me! 9) The dryer has the same locking system as the washing machine. So, if you didnt see the wayward sock on the floor or between the two units until after you pushed (lightly, of course) the start button, you have to stop the unit before you can open the door to throw the sock in.I didnt mean to write a novel (about a washer and dryer, no less)! But, I feel better and hope that I have saved one woman from making the same mistake I did. Read those reviews AND believe them. And by the way, my friend who recommended the Bravos XL to me looked at mine and said Thats NOT my washer and dryer. Evidently, mine was the new and improved version! So much for that claim!

We purchased a Maytag Neptune series washer/dryer set approximately 5 years ago. This is the 2nd time in 5 years that we were told by our local repair person that the drum of the dryer got bent out of shape. This is from normal use and due to a bad design on their end. Maytag refuses to foot the bill (about $350-$400) as it is out of warranty.

Absolutely the worst experience ever. The repair people that were sent to address the problem were great but the Maytag people did not care. I bought a new electric convection oven, the convection never worked. The repair people came out several times and checked and adjusted to try to fix the issues but the oven is totally inconsistent. Even the repair people thought I should have gotten a better response from Maytag! Maytag just said that I had a repair but not replace warranty - of course the warranty period is over now. I had trouble from the beginning, I would never buy another Maytag product. I thought that a company that supposedly has a great reputation would care more about their customer.

I am 86 years old and have happily owned Maytag washers for many years. I just recently purchased the front loading model for ease of access. After using it for sometime, I could not be more disappointed. The clothes come out smelly, stained and gray. I tried using affresh washer cleaner on hot setting and the tablet did not even dissolve. There is black mold growing and must be cleaned constantly. I am so sad that my favorite company has let us down. I cannot afford to buy another washer so I am stuck with this lemon!

Our Maytag French Door with freezer on Bottom MFF2258VEB quit on us after three and a half years. Called local authorized Maytag dealer. They sent out a repair man. He said the main control board was bad! After much discussion we told him to replace it. After part and labor $261.00 it is running for now. Then called Maytag to see if they could reimburse us for the part $161.00. NO DICE! I have a kitchen full of Maytag products and a washer-dryer set but will not BUY ANY MORE Maytag products. Pass the word to boycott all MAYTAG PRODUCTS!

We trusted the Maytag name to give us a good product that would last. After six weeks the Maytag Bravo stopped working. Having to wait 7 days before a service repair person came to our home. The main motherboard needs replaced. So currently, we are still waiting for the part to arrive and have it installed. 2 weeks without a washer after spending 600.00 for a new washer. There is more problems also, this machine takes 1 hour to complete a single load of laundry. Plus it does not get the clothes clean and the rinse cycle does not get all the soap out of the clothes. Very unhappy with the Maytag Commercial Bravo. Will not buy another Maytag product. Save your money and get another brand. We plan to get this one fix and sell it.

Dishwasher MAYTAG MDB7749SBM - Have the same problem as everyone else, panel board. Initially lights randomly blinked, flashed etc, but still washed dishes. Now it has completely died. Dishwasher is 3 years old.

We had a wonderful Bisque Maytag double oven in 2002. We bought new stainless appliances this year, and have been very disappointed with the range. Why do you have to hold the temp and timer settings one increment at a time to set it, and why do you have to push Start after that? Frequently we set the temp or timer and walk away, only to find that the oven or timer did not begin because we forgot the new step. When the timer goes off, you have to push it twice to get it to reset. The burners themselves have too many confusing pictures for the settings. What happened to low heat, medium and high and hash marks in between? The stove top itself is a nightmare to keep clean. Give me back my coil stove any day!!!

We bought a Maytag gas range in Feb of 2011. Shortly after that, we started having an intermittent problem with the oven not maintaining the temperature. It sometimes would not heat up to the proper temp or sometimes would get there but not maintain it. We have had several service calls all for this same problem. Each time they would replace things... nothing worked! We called Maytag and they said they wouldnt replace the unit until the same part had failed 3 times. Well, the service company came out 5-6 different times in the first year and replacing the main panel twice and the sensor and some other thingies I dont even remember. Pretty soon the warranty was running out, so I bought an extended warranty due to the fact that the unit had never been fixed. They sent out two different service companies who also were unable to fix the unit. It is now 18 months since we bought it, and Maytag refuses to do anything since it is out of warranty and the extended warranty company will only replace the unit up to 75% of its cost. So yes, we are very angry with Maytag and the way they wont stand behind their product and their total disregard for their customers.

Theres always a problem with this thing. It doesnt clean the clothes, its always off balance, and now it leaks from the bottom side of the machine in the clean washer cycle. Its only 2 1/2 years old. Should of listened to the guy who fixed my old machine. Dont get a Maytag!

We purchased washer at Sears 6 years ago. Have had same issues for 5 or more years. Sears has been out to check it 6 to 7 times! They clean it out, tell me to use (expensive) Affresh tablets monthly, problem solved but it never is! When we run our washer and walk in laundry room it smells like a sewer. If we open lid its even worse. I use Norwex all naturally, biodegradable laundry detergent. There is nothing Ive done to create this smell. Its a manufactured problem that probably relates to ALL the other issues with this crappie washer that Maytag will do nothing about. I called Sears for 7th or 8th time, said they could send someone out AGAIN, I said thats a waste of my time and yours. They told me to call Maytag. They wont do anything (warranty is up). Of course there are NO ISSUES OR RECALLS on this washer and obviously there should be with not ONE good review! Im angry. You all should be too. We paid good $ for a product that used to have a good name and they are screwing us. I think we should ban together with a class action lawsuit. Please give me your thoughts. They know something isnt right and they shouldnt get away with this.

Purchased an over the cooktop microwave 3 years ago, it came with a 20 year warranty. It stopped working and I promptly emailed Maytag customer service. It took them over 3 weeks before they responded. That is not acceptable. Did they think I had a back-up microwave to take its place until they finally got around to reply to me? Well we could not wait, and we just threw that piece of junk out and had it replaced with a competitors unit. We will never buy Maytag again and will inform anyone we know about the poor operation of Maytag products and lousy customer service. My suggestion to anyone considering Maytag products is to not waste your time and money and look to another manufacturer.

I bought a Maytag dishwasher (Model: MDBH949AWS2) from Home Depot on 07 April 11 and it died 24 August 11. I called Maytag to set up an appointment for repair. The repair person showed up and stated that the control panel needed to be replaced. Apparently, if moisture gets into the panel it shorts it out. One would think that when designing an appliance that utilizes water and creates steam, it would be sealed. Anyway, the repairman explained that because the dishwasher was in a residential program, the warranty was null and void. I wish that someone would have explained this before I purchased it. I went online to AppliancePartsPro.com and ordered the part for $100.75 including the shipping cost. Then, I went back online to look up how to install the panel. The repair person said that they are charging $133.00 for the part and $129.00 to install. A small star tip screwdriver and 15 minutes was all it took to fix. From what I have read, this will not be the last control panel but, at least, I know how to fix it. Another thing that I know is that Maytag is off my list of future appliance purchases regardless of where Im using them.

I have to agree with all these other reviews. This washer twists clothes and does not wash them at all. If you open the lid mid cycle you will see dry clothes on top... Isnt that the whole purpose of a washer? WTF. Steer clear of Maytag. They realize that theyre selling washes to Generation Xers and they can get away with it because we were the first throwaway generation. Great business plan Maytag!

I’m 41 years old and finally had my first new washing machine. Four days later, while my 11 year old had the stomach flu, it died. Not impressed. Apparently the delivery guys left a note on our file saying there was a defect on our washer and that we needed to contact Maytag. This was news to us when we called The Brick today. I hope they didn’t knowingly sell us a defective washer. Alas, we have to wait until Monday with pukey sheets in the washer.

Maytag Dishwasher MDB7749SBW03 - We purchased this dishwasher in 2013. About 1.5 years after purchase the control panel started to get flaky and different settings wouldnt work. Not long after that it stopped working at all. I did some troubleshooting and found that the ribbon cable that connects the control panel to the control board was corroded due to water/steam getting to it. Since we were past the one year warranty I bought a new control panel and things worked fine for about a year, now the panel is going bad again. I contacted Maytag and they said they cant do anything to help me. This machine is not even 3 years old and going on its second control panel. I would recommend staying away from all Maytag products.

I wanted a small stove that did what a large/standard stove could do. I was worried that the heat would be weak but it cooks my food amazingly well. This stove has all the bling of a simple stove for a smaller price and size for my tiny house.

We are a family of nine so I wash a lot of laundry. We bought this washing machine a month ago and hoped it would perform like our prior one. The problems are many. It is too smart for its own good- it requires a cleaning after every 30 washes but gives you zero warning beforehand so you will already have the clothes in and started the cycle when it will stop the cycle saying it needs cleaned. There is nothing you can do to override the cleaning cycle, so you are forced to remove your sopping wet clothes and run the cleaning cycle- wasting time and money on precious water! It also wants you to use its specialty affresh to clean it with, adding cost we hadnt planned on. Then you cant tell when to put the clothes in as it tells you to start the washer and then add the clothes, but if you put the clothes in first sometimes it wont start because it wont sense properly, and if you start it without the clothes. Then when you stop to add the clothes it wont start it with the clothes in it- which way does the machine want it?! So it is a guessing game as if the washing cycle will even start. And the washer wont hold as many clothes as our last one did. If there are too many clothes, the cycle will stop and it will refuse to wash until some are removed. Whenever there is a problem starting, which in one month has been four times now for us, it is a huge guessing game as to what is wrong for why it wont start. I dont need this kind of frustration! Further, the locking mechanism in the washer is plastic, and I know from experience that plastic parts will be the first to break. Had I realized this before purchasing, I would have looked for a metal locking device. My guess is when it does break, the whole washer will break. Also, from day one, it has made a sound that Im not sure is normal. It sounds almost like grinding gears every time each various phase starts or stops (washing, rinsing, draining, etc.). I sincerely hope this isnt a manufacturer defect as we didnt buy the extended warranty. We researched this model before buying and many were happy with it but I hate this washer! I loved my last Samsung washer but it rusted all over after just five and a half years even though it still worked great, so I didnt want to buy Samsung again so we took a chance with this Maytag. I am regretting this purchase. I consider myself to be a person easy to please. I want a washer that works that wont rust that you can put a ton of clothes in and throw it in the wash and forget about it. I dont want all this high-tech sensing stuff that just messes up and is highly inaccurate in what it senses! Why cant companies offer a simple, high quality product anymore that works, without the added costly features?! The model number is: MVW6230HW0. Avoid this model number.

Replaced my leaking Samsung washer with a Maytag and I really regret the switch. What a piece of garbage. It has been service twice (thankfully within the first warranty year) due to Main control board failure. Seriously, these washers are good for nothing. Also, the Sanitize cycle doesnt do a good job from day one. Save your hard earned money and buy something else.

Purchased the Maytag Bravo Nov 2010 and had to replace it after just 5 years. In the five years we owned it, it required a new water pump and the stabilizers had to be repaired. Its motor burned up and I was not able to find a replacement. I was quoted $224 (parts only) for a replacement motor and 10 weeks delivery. My wife never liked the machine as it was not able to clean clothes that well. We did not find much difference in any of the settings. We tended to put very few clothes in each load in order to get them clean. We were dissatisfied that it did not have a soak cycle and the lid lock was particularly annoying.

This Maytag is about 7 years old now, at least, and is still running strong. The one thing I do miss, though, is the lint collector basket that used to be on GE washers Ive had in the past. Kleenexes have a sneaky way to getting into the laundry and picking out the remnants is a royal pain! The lint basket on the GE would save me that task.

Maytag is supposed to be the best. I wanted a top loader again. This washer is almost worthless because of the water control. I have to add buckets of water before I start the washer. Otherwise the clothes are not clean. The cycles are strange with the amount of agitation. I will continue looking for an OLD model. DO NOT BUY THIS WASHER.

This is my THIRD dishwasher, and by far the best. The Bosch machine I had before that was a catastrophe: mediocre cleaning, intense filter cleaning required - at least every two days - and, with a pretended noise level of 47 dB, MUCH noisier than the 50 dB announced by Maytag. Somebody is laughing at someone! To sum up: the Maytag MDB4949SHZ cleans dishes incredibly well, is very silent and requires no filter cleaning.

A lot of the reviews contain complaints about the Bravos XL MCT top load washer. We purchased one in December, 2015, and so far have not had any problems. We had a 3 yr old Whirlpool side loading washer that we just gave away, as it never got enough water to even dampen a comforter or quilt. This machine works very well, in spite of lower level of water. I was pleasantly surprised when I could see the water level with the first load! The controls are not as intuitive as other machines; e.g. spin only requires you to select Rinse/Spin cycle, and THEN turn OFF extra rinse. Perhaps the proper way is to have a Spin-Only cycle, and then tell the user to click the extra rinse ON. We do probably 1 load a day. Water bill has not been significantly higher than when we had the Whirlpool that hardly used any water. Today, though, a heavy quilt (it WAS distributed evenly around the impeller) was put on Bedding so the water level would be a bit higher to ensure the entire quilt was wet. Fine so far. However, during the Spin Cycle, the unbalance became so violent that the washer stopped for a few seconds and then went BACK to the Rinse cycle. It did this several times before we realized that the time remaining had not gone down in over 30 minutes. My guess was that the sensor believed that maybe some additional water with another Rinse cycle MIGHT even out the load. It didnt. I finally stopped the machine, redistributed the quilt and then ran the Rinse/Spin cycle, choosing NOT to do the extra rinse. All came out fine. There was NOTHING in the manual indicating that this might be needed, except for the instructions to Spin only. If I have any other problems, I will send here.

I purchased the Maytag refrigerator MFF2055DRM on 7/7/16 new. It was suppose to be stainless steel; but now I am seeing rust spots at the top and bottom of the French doors. I clean my refrigeration weekly and find it odd that now it is rusting. Also, I am able to place magnets on the doors - which should not be for stainless steel. In addition, I spend over $100 a year replacing the mandatory filters. I must also place the setting to high to maintain my milk and juices. I must also have to place them in the very back of the refrigeration. I am a single senior and my refrigeration is not overloaded with food; nor am I constantly in and out of the refridge. Not very happy.

I live alone and bought this unit for long life. After a few short not-used-much years, my washer sounded like a 747 was landing in my laundry room. I am a maintenance person, so I did a bit of troubleshooting and narrowed it down to the bearings installed in plastic on the outer tub that failed. My cost was $600.00 to $750.00, parts alone. It still worked, just very noisy on high spin.I emailed Maytag (now Whirlpool) and was phoned by Lee Ann. I told her I had all Maytag appliances in my home and was laid off and that if after the use this washer has had and it will cost this much if I do the work, I was not impressed with this company. She apologized and told me she will issue me an extended warranty for $299.00 that will cover it. I told her that without a job, I cannot make a decision so fast. She gave me the next business day to decide. I concluded it was cheaper than the part, so I called her back. I was scheduled for a repair, and the man opened the front and looked at it and said it was an outer tub bearing. He went to his laptop in his truck and returned to tell me that they would not authorize that expense and that all they would authorize was $350.00. He put the front of the washer on, then as if he forgot something, took it back off and reached way in the back and did something. Then, he reinstalled the front. I was livid! They charged me $299.00 for a warranty and would not repair! So I called back and was hung up on. Next, I called my credit card and disputed the charge. I tried to use the washer, and it made funny sounds and then filled up my home with smoke and stopped working. I called Maytag again, and he denied the repairman would tell me how much they would authorize to repair it and told me good news that they would issue a $174.00 check. I gave $299.00, and a few days later, they give me $174.00? This is why Whirlpool is destined to fail. I will never buy again, and I will wash in my laundry tub first! This is exactly why imports will rule! So Whirlpool, you got me for the last time!

My washer (Performance Series 4000) needed new bearings about 6 months after purchase. By the time the parts came in and after the A&E repairman rescheduled because he didnt know how to replace them, another two months had passed. Now, a year later and with no more warranty, the bearing needs replacing again! This washer is only 1 year 8 months old! The first repair cost well over $1,500 but was covered under warranty. There are hundreds of other people with Maytag washers having the same issues! Maytag is well aware of the defect and refuses to take responsibility. I would like to file a class action lawsuit against Maytag. Im in Tennessee. Please contact me. Thank you.

I purchased the Maytag 6.5 inch electric convection oven about 2 years ago. I wish I hadnt. The oven temp is way off, it cooks unevenly, the back burners hardly work, and the back burners on the stove top barely work, the knobs get stuck constantly, the self cleaning does not work, and the glass part of the door allows dust to get trapped in the glass. The range is $800+ piece of junk, best used at the scrap yard. Today, I turn my oven on, and the element underneath the oven pan caught on fire. Now its broken in half, and needs to be replaced. I look up the QR code, and come to find out the oven is actually a Whirlpool, with Maytag labels on the outside. I would have never purchased this range if I knew it was a Whirlpool. I have always had issues with Whirlpool appliances. This is a fraudulent product, and deceives the customer. Why sell it as a Maytag, when its really a Whirlpool? It should at least state that fact on the description, and salespeople should advise the customer. Now I know why its a piece of junk, because its a WHIRLPOOL!!! I will never buy a Maytag or Whirlpool product ever again. I have always stuck with Maytag appliances. Every appliance in my house is a Maytag, or are they Whirlpool?

We bought a Maytag dishwasher (Model: MDBH979AWS3) in January 2010. In April 2012, the control panel stopped working. A local repairman came out to see it for $160, diagnosed it, and suggested that we call Maytag to see if they would give us the part because it was only a two-year old machine. He did say that the control panel was not a part that was troublesome!Maytag offered an extended warranty for only $287 that would cover the part! The total repair cost was almost equal to the cost of a new machine. Home Depot, when consulted, acted as if they know nothing. After reading about other peoples experiences with this company, I feel that it is no longer an honorable company standing behind its products. In fact, the whole repair process is set up to rip off the consumer.We will now look to purchase the best and cheapest non-Maytag product, not from Home Depot, and throw it away when it gives out, which more than likely will be soon. These companies have finally convinced me to do what I am sure what they have always wanted every consumer to do. Throw it away when it breaks down.

We purchased our Maytag Refrigerator Model # MBF2258DEHM on 12/21/2015. Just a couple of issues I would like to bring to your attention before you purchase your Maytag. The single refrigerator door does not close automatically. You have to close the door. The metal handle is metal and has a metal smell and feel to it. The stainless steel door and the handles are not the same finish. Although this might not be a problem for some who like the industrial look I prefer my hands to be free of chemicals while I am preparing food. The ice maker takes up too much room. The ice maker should have been an option, not a standard item. I had a Kitchen Aid for 10 years and loved it. I thought I was going to have my Kitchen Aid for 15 years or more. I would have purchased another Kitchen Aid, but the reviews were not good.

I purchased my first Maytag (Bravo Washer) appliance in 2013 and thought this washer would last me for a minimum of 10 years. It started making noises occasionally right away but I wasnt too concerned until it started sounding like someone was banging on it with a sledge hammer. I waited 8 days for a repairman who told me the bearings were going out and it would cost $400-500 to repair. This is the worst washing machine ever manufactured. My advice is to buy any other brand. Dont be fooled by the Maytag hype. Their quality is nonexistent. I am shopping for a new washer.

We purchased our Maytag dryer at Home Depot a couple of months ago. We just called Home Depot for the second time because the dryer handle broke off while opening the front load door. We called Maytag and they tell us to call Home Depot and the only thing they are willing to do again is fix the door handle which will probably break off again while Im in the middle of laundry and cant retrieve clothes from the dryer because there isnt a handle to open it.Im convinced the dryer has a defective handle, and the dryer should be replaced considering what we paid for it. But Maytag or Home Depot doesnt want to do that. I will never buy Maytag products again and thinking of buying products at small appliance stores who stand behind their products, instead of Home Depot who could easily turn our dryer over to the insurance company as defective for the loss.

Bought top of line Maytag dryer and washer in 2011. Immediately had problems with dryer. Dryer resets timer itself to outrageous times. Clothes so dry they could have been parchment. This has continued with multiple service calls and electronics replaced. Still continuing but they will not act lemon law. I have extended warranties but get runaround everyone including Sears where I bought it pointing to each other. Tech came out today and said problem was the way the dryer is. No way to change it. I guess that is nature of the beast. I will never buy Maytag or from Sears again.

My refrigerator is several years old, and I would buy the same brand when I need a new one, although I would hopefully buy a counter depth one because my kitchen is so small, and the one I have now is kind of big for the space.

We purchased Maytag Dishwasher MDB5601AWW/46171101NP when we built our new home. In the last several months, water was leaking out onto the floor. We called Maytag and they told us there was a recall on the heater element and that they would send the part out. We made sure they knew the reason for our call--TO REPLACE THE GASKETS!. Maytag contacted a local authorized repair person. When they called to set up appointment, my husband reminded him about the gaskets. The guy showed up without gaskets, saying Maytag didnt put it on the order! We called Maytag to set up another service call. The guy showed up again today without the gaskets. We were told they had to be ordered and that he would have to come out again! Three service calls for one issue! Aside from this, the circuit board has never worked right. We push the correct buttons, but never know what kind of cycle we will get. We learned to live with it. Our bottom racks are melted as well as the sides of the dishwasher. Now that we know about the heater element being defective, this may be the cause of the bad gaskets and melted racks. It will cost almost $300 just to replace gaskets, and yes, we have to pay a service call for it when it could have been done in the first place. We called Maytag to complain and were told that replacing the gaskets always takes two service calls--one for diagnosis and the second to put in part. They said they dont take the customers word for it when we tell them whats wrong!

Purchased model MBF1958XEB4 September 2012. The unit is provided with a bottom freezer. About 2 month age water was forming and freezing on the bottom of the freezer compartment and leaking on the floor. It appears that this is a common design flaw recognized by Maytag with an updated part available that is intended to correct this problem.Contacting the extended warranty company I was informed that this is normal maintenance and not covered under the plan. Liars!! One does not remove a car engine to change the oil. To correct this problem the refrigerator is required to be pulled from the wall, disconnected from power, remove the back lower cover, disconnect two wire cables, replace the drain tube and reverse the process. Normal maintenance - give me a break. The company promoting this phony plan is Federal Warranty Service Corporation in Atlanta, GA. Do not buy a plan from them and if you have one cancel and receive a refund if possible. Maytag get into another business because your product is junk.

We had this washer 16 months. We bought it new from Home Depot. The clothes came out with spots on them, white residue and grease spots. This was ongoing for awhile. The bearings went out after 6 months. It was so loud now the water pump went out. I was told by Whirlpool (they bought out Maytag) that water pump is on back order and could take a couple of months!! To fix the bearings and the water pump was almost 700.00. A new washer is 1000.00. We junked it and had to buy a new washer GE. We are sick about this waste of money!!! What a piece of JUNK this Maytag Bravos XL is!! We need to have a class action suit and try to get something back. This is ridiculous and they arent taking responsibility. Whirlpool/Maytag are rip offs!!!!

We purchased a Maytag dishwasher mdb7749sbm1 in 2014 and have had nothing but problems with it since it was delivered. Within a year of owning it, the top jet fell off. We had it replaced and the repairman warned us that it would probably come off again due to a faulty latching system. In the last six months one of the brackets that holds the upper shelf has broken off and the dishwasher leaks every time we use it.My last cycle leaked so bad that essentially it completely soaked the extra large bath towel we place in front of it and travelled halfway through my kitchen. Not to mention that it never washed dishes well, regardless of what cycle we use, which/how little or much detergent/rinse agent and it does not filter at all, as theres debris all over my dishes and glasses. I am now looking to replace it before like other reviewers a control panel fire occurs. Strongly recommend staying away from this brand.

I bought a Maytag washer, dryer, and a dishwasher from Home Depot. It has only been a year and 1/2 and the washer has already broken down. Maytag wont help and neither will Home Depot. We are two elderly ladies (sisters) that used it once or twice a week. I feel we got ripped off. We cannot afford parts, labor, or a new washer. This product needs to be pulled. And Home Depot should not sell anything that is not a better quality. I trusted both companies and am sorry I did. Thanks.

I will never buy this product again or anything with the Maytag brand. I purchased my washer less than a year ago and it makes all these awful noises. When called company they would not come fix it. Money wasted.

We bought a Maytag Bravo model top washer recently and have no good things to say about it. The startup time is too long and clothes are coming out with lint all over them now. If the unit could be returned we would do it immediately but we cannot.

Thankfully, Home Depot replaced the washer when Maytag wouldnt authorize a replacement after I had it for 3 days. Maytag wanted me to order a part, wait for the part, and then schedule their third party service contractor. It’s been about 2 weeks without a washer. Ive been posting about my experience and received an email from Maytag asking me to post feedback on their site, but it was rejected. Their note to me was “Our publication guidelines do not permit content that references a service policy, customer service interaction, or customer service question.” In other words, theyre not at all interested in customer service. Maytag/Whirlpool is no longer the brand to look for.

We bought MDB7759AWB Maytag dishwasher in 2011. It worked decently until now when it stopped delivering water to the upper rack. The cleaning quality on the lower rack also dropped significantly although it might be due to the lack of water delivery to the upper rack. Apparently there is something wrong with the internal pump. The Maytag service offered a repair for $300+ which I rejected because this is a ridiculous cost and I would rather buy a different dishwasher. My conclusion is that if you buy Maytag dishwasher you need to factor about $300+ for the repair(s) in 5 years as apparently they do when they sell you this product. Anyway, even though Maytag was a decent brand a long time ago (probably in the past century), it is not reliable anymore. It does not mean it has to be much worse than many others but if you are looking for something better than those others I would not recommend Maytag.

My front load Kenmore just fell apart. I guess Im lucky I have had it for 8 years and now its broke. I could fix it but thought it would be better to get a new one. I looked at all the reviews for front load washer and could not find one that had positive reviews. So I went with a top load. After reading all the complaints I might have made a mistake, but its too late now as it was delivered yesterday and now doing the clean cycle. Oh my…what junk they all produce now - a true throwaway society. My refrigerator is still working after 24 years what a gem of a product. Happy days.

I purchased a Maytag dishwasher at Home Depot in Roanoke, TX on 07-14-2011. Model Number: MDB7749AWB2Serial Number: F12604431Unfortunately, Ive just been obliged to open my third service call on this new dishwasher. The first service call was made in August 2012, just outside of the first year warranty period to repair a wire which had come loose in the control panel, making the dishwasher inoperable. The second service call (May 2013) was to replace the front panel housing and touch pad which had broken off at the screw-mounts holding it on to the door. As the handle to open the dishwasher is part of the front panel (which must be pulled out pretty hard to open as it does not have a latching mechanism) screws set into unreinforced, thin, plastic posts holding the panel to the door seems like a serious design flaw.The third service call which I placed last week (August 2013) is to address the fact that the dishwasher has become completely inoperable with no lights on the front panel and is completely unresponsive. To say the least my experience with this product (and by extension the Maytag brand) has been a serious disappointment. I guess the reason I no longer see those TV commercials with the lonely Maytag repairman is because these days hes actually really busy fixing broken down ** Maytags. I will never, ever buy any Maytag or Maytag-family brand appliance ever again.

Have had this problem since week 2 of ownership. Even on the lowest setting, food in the fridge section is freezing and Im having to throw out fresh produce weekly. Called Whirlpool service since under warranty. The very nice service man replaced the thermostat. Only a little bit better as the temps do not range quite as extreme - only 25-46 now! I am now waiting once more for a service appointment, at least 10 days. Plus in Massachusetts they will only give you a 8-5 service window. They give a robocall the night before and you are given a 8-12 or a 1-4 time for your appointment. I also have had trouble with the meat drawer falling out of the track because the upper shelf bows with the weight of a normal amount of stuff. Now the bracket has cracked and the meat drawer no longer stays on the track when it pulled out partially (such as when you need to reach in and get something). Same thing happens with the lower drawer on the right side although the bracket hasnt cracked.

I purchased a range 5 months ago. It is STAINLESS STEEL. It began to rust. I called customer service and they told me it was cosmetic, so they wont help. I think a stainless steel range should not rust after 5 months. Very disappointed, WILL NEVER BUY MAYTAG Again.

Bravos quiet series 300 - After reading reviews on this washer and dryer I have to add my thoughts. I bought this set a few years ago and initially was very pleased. However, I am now having the same issues as everyone else. The bearing on my washer is bad and needs replacing to the cost of almost a new washer. My dryer started acting up at the same time, my clothes would not dry at all and I discovered the inside of the door was wet and after pulling out to check the wall vent, the vent had water puddled up inside the wall. The tubing from the dryer to the wall had mildew growing in it. Which may explain why my towels and clothes come out of the dryer smelling like mildew! The repairman was here today and repaired the dryer, there was a large amount of lint at the bottom of the dryer once he opened it up, which I believe could be a fire hazard. The seal (or felt seal) around the drum was coming off and had to glued back onto the drum. The belt under the dryer had come undone causing the dryer to not dry, but would spin. It is a shame that Maytag has not resolved the issues that everyone seems to be having, even if it has been years since we all purchased their product. Maytag is supposed to be a reliable product name and you would think they would like to fix this issue to keep their name clean! My first washer and dryer (which were Maytag) lasted more than 12 years and cost a lot less than this set which I dont think is more than 5 years old! I hate to spend more money on a new machine, but I may have no choice. Very sad customer right now.

Model #MFI2670XEM0, Maytag fridge top French doors, bottom freezer. Purchased fridge in May 2011 from Lowes, with a matching microwave. A couple months ago, I noticed puddle of water on wood floor in front of fridge, so I opened freezer to find ice on bottom with a sheet of fresh water on top. Call to Maytag was useless, also tried to sell us warranty. Guess that $300+ warranty would cover one year, so after the warranty runs out, would we have to buy another when it plugs again. Our kitchen floor is ruined, and the warping is coming close to our dining room. Googled problem online to see if there was an easy fix since it was out of warranty. I tried to defrost as described online, only to have it leaking again a couple weeks later. Will never buy a Maytag again. Guess that repairman in commercial is never busy because Maytag wont stand behind their products.

We purchased a wall oven model MEW7530DE 11/8/2014 which was installed the first part of December 2014. From the beginning the temp was not constant and everything baked was either burned or under baked. The first repairman said the control panel was faulty and was replaced four months after purchase, the problem continued. After three more repairmen all from different companies concluded they could find no problem and thats just how ovens work now. We contacted the owner of Hamiltons Appliance, where the oven was purchased, and requested a replacement oven which was accomplished December 2015.New oven, same problem, very disappointing. My wife has been baking for over 50 years and has never experienced problems and frustration on this level. The condition of the oven is totally unacceptable and with all the effort by us and others we are at a loss. We purchased an extended warranty which has resulted not fixing of the problem. We hired an electrician to inspect the wiring in case that was the problem, costing us $200. The wiring was all good. What do we do next and what are our options short of another new oven. WHAT IS MAYTAGS RESPONSIBILITY? Respectfully, a very unhappy customer.

I purchased my dishwasher exactly two years ago. We are empty nesters so it has had light use. Today, when I tried to start it, the control panel would not work. Thanks to what I found in your site. I will not take a day off of work to wait for a repairman only to have it fail a second time. It is hard for me to believe a company that builds its reputation on a bored repairman would produce a product with a faulty control panel and not do something about it. Like your other folks, I will never buy another Maytag product and will not the waste the money to repair it. I am going out tomorrow to buy another dishwasher and throw this one away.

Unreliable! When you push start, it goes into sensing mode and starts to fill. You walk away thinking it will run to find out an hour later it is still in sensing mode! Wasting electricity, your time and talk about stress! You have a 50-50 chance it will go on and run the load, but if you dont have time to stand there and watch it. FORGET THIS WASHER. Also does not clean as the old agitator washer, which I luckily still have, yeah. Always read reviews before buying anything. Nice website.

I purchased the top load Maytag Commercial Residential washer with an agitator last month. I wanted a basic washer with Hot/Warm/Cold settings, Delicate/Normal/Heavy Duty cycles, Small/Medium/Large loads. I paid over $800 for this washer and I cannot wash my whites or rags in hot water! The hot water setting dispenses hot water, then cold water, back and forth. The end result is cool water. Ive called Maytag, Ive been told that there is nothing that can be done about it, thats how theyre made to be considered HE. I asked them why they even put a hot or warm water setting on the washer.You have no control over the water level, all cycles except for normal run in a deep water setting (full drum of water), I dont know why delicates are in a deep water setting. I only wash a couple pieces of delicates together. I end up using a lot more water and detergent with this washer. I hope we dont have to conserve water in the next few years! So though this washer uses less hot water energy, it wastes a lot of water, my water bill goes up and my detergent is used up much quicker! I cannot add time to my wash cycle, (the actual washing/agitation cycle is very short - 10 minutes) it has to drain all of the water and re-start the cycle with more water! $800 is a lot of money for a washer that doesnt wash like my old cheap washer. The local store cant do anything about it and Maytag brushed me off.

Maytag Bravo Quiet Series 300 - I purchased the set 2.5 years ago and after 2 years, it started making a rubbing sound. I kept using it with having a family of 5 and this is why I purchased it in the first place; with 3 boys, I do a lot of laundry. It then quit working on me all together and wouldnt spin the clothes. I had a technician come out and it was the barriens that spun the drum so I had them fix it and it cost me $400. Then about a month later, it was flashing code F51 and not spinning. I had them come back out thinking it would be covered since it just got fixed but no, it cost me another $100. Now, 6 months later and here I am again unable to do laundry because its flashing F51 and wont drain or spin. I called Maytag and they tried selling me a warranty and said it wasnt recalled because there wasnt enough complaints. We need to all call and raise a ruckus. This is ridiculous. Sorry to hear everyone going through as I am.

This Maytag dishwasher is beautiful inside and outside. I love that the controls are hidden. It cleans dishes very well. It has a large capacity for dishes, a rack for glasses/mugs, a small rack for cooking utensils, and a container for silverware. It is so quiet you hardly know it is working. I would highly recommend it.

Maytag mod# MBF2258XE81, Ser# K04712605. 3 years old. At 6 months old, the drain plug clogged. Freezing water under pull out drawer of freezer, spilling onto kitchen floor. Fixed under warranty. 9 months later the same thing. I had to pay $190. Now, it has been happening for 6 months, and I use a spatula to lift the sheet of ice out. I have to do this every 10 days, or it leaks onto the floor, tile and rug in my kitchen. This is just wrong. I see I am not the only one. If Maytag does not fix this known problem, I guess I will get a new fridge. I had my last fridge for 21 years, never had problem. Thought I was upgrading.

I purchased my Maytag Neptune pair on Jan. 24, 2005. I was unaware of the problems and lawsuit related to these items. Luckily, I didnt have any problems with them until May of this year. At that time, I spent $337.00 for a new control panel for the dryer. (Just because I didnt want to split up my set.) I expected them to last me for the rest of my life. Of course, the washer had started to do something even the repair man had never heard of before, right about the same time. I told him that the tub would fill up with gallons of water, and surprise me when I opened the door on various occasions, flooding my laundry room and the basement downstairs. Mind you, this would occur even with the water supply cut off to the machine, no hot or cold running to it.He performed a diagnostic test on it and said everything showed up fine. Of course, it didnt overflow while he was here. He is the one who told me about all the trouble and the lawsuits. I had wondered why I didnt see them for sale anymore. I have been keeping the water turned off except when I need to use it after all this time. It still happens! The repairman thought I was senile or something. I dont have a mold problem, no trouble with the door lock (yet), and out of all the comments and complaints Ive read online today, only this site had one with a problem of it flooding the house. My husband and I are on a fixed income, and here is this unit (that I thought would be my last) rotting out my floor and wall in the laundry room, and flooding my basement. Not to mention it rusting out the inside of the washer and its pedestal. I would like to hear from anyone else who had this water problem, and what it took to fix it.

Maytag Free Standing 30-inch Gas Range - In 2004 we bought our model MGR5775QDS gas range with 5-burners because it offered the most BTU variety for the price: 1 burner with a high BTU (16K), 1 with low (5K), plus 2 in mid-range (9.5K) and 1 with 12K. Within half a year of using the oven, we turned on the self-cleaning function. Big mistake. One cleaning cycle later, our oven refused to ignite. The cleaning cycle burned out the ignition unit. Cant remember if its replacement then was under warranty but the repairman said this was a COMMON PROBLEM with Maytag and we best not use it EVER. In 2014 our cleaning lady mistakenly thinking she was doing us a favor, set the self-cleaning function. Once again, the ignition unit was destroyed. This time its replacement was $350 with part and labor. One and half months later, the oven is again non-functioning. This time our repair guy said the part is a very minor, inexpensive one BUT MAYTAG IS NO LONGER MAKING IT!!! The only way well get our oven back is if he can find another model and cannibalize it to fix ours. Are we disgruntled? Yes. Would we like to see a class action suit against Maytag for knowingly manufacturing a gas range with a malfunctioning self-cleaning unit that destroys oven parts? Yes. Will we ever again buy Maytag? Not on your life. A once stellar manufacturer gone down the tubes with a growing reputation for making junk. American-made appliances mean zip these days. Thank you for nothing, Maytag.

Weve had this washer for five months now and really regret buying it. It cannot remove even minor stains and often leaves residue on clothes, even with extra rinsing. I spilled coffee on some fleece pajamas and it took four washings to get the smell out.

I bought a Neptune Washer in 1999. 6 years later (2005), it started making the 747 landing noise. It was implied that somehow it was our fault, maybe, something from my contractor husbands pocket. After all, it was a Maytag, and surely there could be no design or engineering flaw! (My daughter still has 34-yr.old one.) We were told the repairs would be so expensive. It would be wiser to buy a new one. Foolish me, I bought another Neptune to match my dryer. Of course, now this one has the same bearing problem and again its cheaper to buy a new washer. I am angry and not sure how to proceed. Any washer, but especially a Maytag, should last more than 5 - 6 years. I should not have to buy my 3rd washer in 12 years. And if I do, it certainly wont be a Maytag!

This unit is only 4 months old. It freezes everything, vegetables, eggs, etc. It took more than 3 weeks for the technician to show up at my door!! Performed a service modification according to the manufacturer specs. This did not work!! Call again to have a it fix. He show up almost 2 weeks later. This time he replaced a part, worked fine for almost 2 weeks. Now I am having the same problem. I had it with this Maytag piece of junk!! I will never buy anything from Maytag again!! PLEASE DONT WASTE YOUR HARD EARNED MONEY... IN MAYTAG PRODUCTS!

We just replaced our 20-year-old washer and dryer for a new Maytag Bravos set. The Home Depot staff convinced us that top loading units were of good quality and reliable. We were fairly satisfied with our expensive purchase when our washer stopped spinning. We are just past our 1-year warranty of course so we called the service department. A young man in a beat-up pickup truck showed up and spent his time reading the manual that was hidden under the washer. His best guess was a $300 part plus a $100 fee for him to show up. So to repair a less than 2-year-old machine is $400. Im tempted to buy a different washer. It wont be a Maytag, unless you can convince me otherwise. I give you credit for great advertising! I was convinced that Maytag was a good name with limited repairs.

The ranges are getting great but are more so with digital than buttons and knobs which they should still have, especially for the handicapped and some elderly who prefer them. It would help prevent injuries. It was hard for me to find the knobs.

Maytag used to have a reputation for quality. Their low water energy efficient Centennial is a waste of money. Half of the time clothes come out wet and most of the time they are still dirty. Also you are only supposed fill the tub 1/4 of the way with clothes so you end up doing 3 times as many loads per week. What genius came up with this idea? Save your money. You would get better results washing your clothes in a tub with a washboard. Seriously!

We purchased our Maytag 4000 series washer and dryer (Model: MHWE450) in December 2010 from Best Buy. For the first six months or so, we were very happy. We started to notice that the washer was getting a little louder by the month. I checked the level multiple times to be sure that wasnt the issue. Assuming it was just part of how the washer broke in, I just let it go - a bad move! Fourteen months after I purchased the set, the washer flooded all over the floor. I opened the washer and pieces of plastic were all over our clothes. After further inspection, the drain was completely full of the same plastic. I cleaned it all up only to find that the washer tub was so loose that it was banging side to side.I called Maytag to ask for help or suggestions. They basically told me that I was out of warranty and kind of out of luck. I responded that we do a total of four to five loads of clothes per week and that there was no reason that this commercial series washer should have failed after 14 months. They offered a one-time service plus extended service contract. Feeling that I had no choice, I spent almost $400 assuming that I had a fixed washer and a year extra warranty. I was told that someone would be out to look at the washer in three days. Finally, after me pressing and pressing, someone showed up a week later. He put a list together of all of the items that were needed to repair the washer.Two days later, Maytag service calls and says that the washer will be too expensive to repair and they would be giving me a reimbursement for buying a new one. They didnt have an exact amount yet. Two more days later, they finally called me with an offer of around $550 ($250 less than what I paid) based on their research of what I should be able to find one for and directed me to the website. One big catch though - it didnt include the $125 shipping charge. When I called to request for it to be paid as well, they declined with basically a “take it or leave” type of attitude. Not knowing what to do, I called every local appliance store until I found someone that had two in stock. When I went to look at them, I was told that both of the ones that they had were rebuilt because that model Maytag washer had a major issue with the bearing and basically needed to be replaced on all of them.Luckily, I was able to buy the washer and a five-year extended service contract for around $690. So in the end, I paid $799 for the new washer, $400 for a warranty, another $100 to replace the washer, and close to $100 in laundry mat costs for three weeks. I promised everyone that I spoke to with Maytag that I would write a review to share my story and thats why I wrote this. The repair plus warranty is a joke. I like this washer/dryer but will never buy another Maytag appliance again. Next time, I will buy extended service contract from the start.

First off, everyone seeing this should be fuming as I am because we are mostly in the same boat with these control panel issues. Mine is Maytag model MDB7749SBM3 about 575.00. A little bit cheaper than most of you because I purchased at the online and had a rebate. About a couple months after the warranty expired, we started having weird light issues with the control panel where are one light would pop up when you didnt hit it or other lights would pop up when you hit something else. We kept dealing with it thinking that it would dry out and resolve itself. Lo and behold, just like it appears to be tens of thousands perhaps hundreds of thousands of machines, it quit. I read this consumer affairs post after it quit and now I know why it did. I opened up the control panel and sure enough, the little ribbon that connects all the electrical connections had brown on the back like it was burnt through. I was able to find a special 1 800 number that Whirlpool has set up because they have purchased Maytag and the woman I spoke with said they would send a technician out and that I was responsible for the diagnostic fee. I was born but it wasnt yesterday. I immediately said to the woman, Absolutely unacceptable. I am NOT paying for anything, very politely highlighting the fact that I know they settled a class action lawsuit in California regarding a control panel issue and there are hundreds maybe thousands of complaints on consumer affairs.com. The woman place me on hold, I am assuming to speak with her supervisor and then let me know that they would pay for the diagnostic fee. She said a repair date for me for about a week and a half later. The repairman had a good day because the dishwasher was already disassembled for him and he proceeded to take pictures and call Maytag. Maytag told him that I was responsible for the installation cost and service fee which according to the technician is about a hundred bucks. I told the technician that is fine but it will not be fine when I call Maytag back. I have not spoken to Maytag about the hundred dollars needs to file a claim for a new dishwasher and associated damages. I have not spoken to Maytag about the hundred dollars but I am only on this to let you know that every single one of us needs to file a claim for a new dishwasher in associated damages in small claims court. I plan on filing a claim for approximately $700 for a new dishwasher and damages. In my opinion, I feel like we should all do this, otherwise big corporations like this will continue to shovel garbage into the stores left and right.Have a good day and good luck with your court case hopefully. With all the evidence against them, I have a feeling that they will settle this and pay before the court date even comes around. Good luck to all of you. I will try and update this after I call Maytag back for the hundred dollars that they are going to charge to repair their broken part.

We purchased an entire suite of Maytag kitchen appliances in September 2014 at a cost of $4300. Have had problems with every single item. The MMV5219DH microwave was the first issue. After a year it began to give us erroneous display messages when we tried to use it. We would input the number of minutes we wanted the food to cook, and wed get a message saying CHK TIME/OPEN DOOR. Repeated door closings, resets of the time, etc. did nothing. Sometimes if we hit cancel it would work - other times not. Wed push every button on the keyboard and eventually wed get it to work - perhaps 10 minutes later. When I called the appliance store (Vics Appliances in Saco Maine) I was told to unplug it for an hour. Okay, that corrected the issue - for a few days. When the problem continued, sometimes unplugging it had no effect - other times it did. Eventually we figured out if we didnt reset the clock time it would work most of the time (not 100%). The Maytag refrigerator began to malfunction at the same time (not keeping temp, and the ice in the icemaker melting and refreezing in a big lump that blocked the door water/ice dispenser) so we called Vics again and set up a service call. Serviceman reset the microwave to factory specs and we will see what happens. He also reset the fridge to different temps, and 2 days after his visit it has again melted the ice in the icemaker and formed a blob at the bottom. DO NOT BUY MAYTAG!!!

We purchased a new Maytag Bravos X washer and dryer from Lowes in June of 2013. After a year and a half of normal use (2 people in the household) the washer needs a new gearbox bearing at a repair cost of $529.00. I called Maytag and spoke to a customer service representative who informed me that there was nothing they could do about it because it was past the one year warranty. I asked to speak with a supervisor who told me they would offer me a 50% discount on the bearing but would not pay for the repair work (the cost of the bearing is approximately $25).Needless to say I will not be having the washer repaired. We will be purchasing a new washer and it WILL NOT be a Maytag, Whirlpool or any other brand made by that company. Its just appalling to think a company like Maytag can scam customers the way they do by producing appliances that are of such poor quality and then offer third rate customer service on top of it. Maytags answer to the whole issue is selling everyone an extended warranty which we all know is as bogus as the companys integrity!!!

My microwave will not work when the door is shut. It says: Door open. It’s worked intermittently, doing this for about two weeks. Then my husband woke up one morning a week ago and the microwave was on like it was running, light on but the plate was not turning. So we’ve had to unplug it and do without during thanksgiving weekend. This seems to be a common issue, obviously from the reviews below, so shame on you Maytag for not owning up and doing the right thing, covering repairs or sending out a recall. It’s a $112 service call here locally plus parts and labor. I will certainly be telling others not to go with Maytag. Maytag is lucky- it turning on by itself AT NIGHT, WHILE WE WERE SLEEPING, that it did not cause a fire or something. I’m pretty upset that it’s inside a 2.5 year window and already has issues.

We purchased a Maytag stainless steel French door refrigerator from Home Depot in 2011. The thermostat control (a circuit board made in China) broke and was replaced in 2012 by a certified repair person. He reminded me to dust underneath regularly, which Ive done. A couple of weeks ago I noticed some darkening of my wood floor to the left of the refrigerator and so I pulled it out from the wall a bit. What I saw was that my entire floor was wet and falling apart under the left side and when I looked into the freezer, I pulled out the bottom basket and the bottom was covered in about an inch of ice.I called, posted on Facebook and was put on hold several times for as long as 20 minutes before I hung up. I called Home Depot and asked them to intervene and speak to a rep from Maytag. I have heard nothing. There is black mold in the corner of my kitchen and a soaked floor that may go way beyond. I googled the leak and apparently this is very common with Maytag French Door refrigerators. I have a meeting with an attorney. Getting through to Maytag is seemingly impossible unless you have hours to wait on the phone. We have been getting sick for months and not knowing the cause.

I remodeled my kitchen last year. I purchased a stove, a dishwasher and a built-in microwave. Two days ago, I was trying to cook rice in the microwave. I changed the heat to 50% to cook the rice, started to cook and I heard this awful noise like a shot gun went off in the kitchen but the microwave was still going, I opened the microwave door and then I turned on the microwave again. At that time, it started to rattle on top of the microwave and shorted out. Black smoke was come out and I saw fire coming from the same area on the right upper corner. I got up on a step that I have and blew away the flames which were not big but if I were not in the kitchen, it may have caused a fire. I got the microwave from Lowes. Since it is almost to the year that I bought this microwave, they offered to replace it at no cost to me. Im getting the same model but Im purchasing the 2-year warranty just in case. I was told by the Lowes salesperson that this was unusual and should not happen again. We will see; its very dangerous. I had microwaves that lasted more than 10 years and had no problems. Maytag, where are you building your appliances and what about your product reliability? If I knew this site before I bought my appliances, I would not have purchased Maytag.

Purchase in April 2010 on 12/31, motor and computer panel went out, not washing. I do not recommend this dishwasher cost to repair. Too expensive.

I purchased a Maytag Centennial washer a few years ago. In my opinion it hasnt worked properly from the start. We went on the low end of price, because we spent a small fortune for GE products that broke after a year and a half. This Maytag hasnt been a much better experience. First it didnt drain and spin clothes, and I was told I was using too much soap. Cut back on the soap and it started working better and going through the full cycle but the clothes never felt or smelled fresh and clean. Now 2 1/2 years in, it doesnt complete the full cycle on its own, AND there is dirt in my washer after every load. My clothes come out with streaks of dirt on them. The picture below is of a pillow case I just took out of the wash! Ive cleaned the washer multiple times, but it doesnt drain properly so it doesnt help. Maytag charges a service fee just to come out and troubleshoot and charges you again to come and do the repair. Im running out of reputable companies these days with washers.

I purchased the Top Loading Maytag Washer and have had nothing but an awful experience with this washer. The dark clothes come out with soap on them. I then need to take a wet towel to wipe out the soap stains. I have had a repairman in 2 times so far and there is nothing he can do to fix it. Maytag said I must wash all the towels with towels, all jeans with jeans, roll clothes into a loose ball before putting in machine, use the extra rinse cycle and the longest wash cycle and do not load clothes more than 5-6 inches high in the tub plus 7 other things I must do to get a clean load and none of those things have worked yet. If the salesperson would have told me all this, I never would have purchased a Maytag and nor should you!

I bought Maytag Bravo washer and dryer set in Nov 2012. Washer door lock broke shortly after 1 yr and now the gearbox has broken. DO NOT BUY MAYTAG BRAVO WASHER. The cost to fix is more than the value. Before the gearbox death the sound it made while spinning was so loud you could not hear the TV or have a conversation in the west end of the house. Visitors were stunned at the noise it made. I called Maytag warranty and explained I am having the same issues as everyone else, what are you going to do? The answer was nothing. Please read the other reviews, same issues. It never cleaned clothes anyway, bad design, bad company and bad corporate values. Model number MVWX700XLE.

My 1 year old Maytag Bravos 300 dryer caught fire on Nov. 21, 2011 after the first one was replaced. Firemen came. Luckily, it didnt spread to the house. The first one wouldnt dry my clothes.

MBL2258XES1 - Like most of the other reviewers, we have a Maytag refrigerator just 3 years old with a lower freezer that leaks water onto the floor -- and has been doing it for the last two years. We have to take the freezer apart (NOT easy), defrost it, take the back panel off, and clear the drain tube. Obviously a defective design! Cant believe Maytag hasnt done something about this!

Purchased a Maytag Bravos washer in 2009. Was told it was water efficient and electric efficient also. Spin cycle twisted my clothes in a knot and left white blotchy doors on my dark clothes, had to rewash my clothes again!!! Then started making a horrendous noise that could be heard from one end of the house to the other, like it was going to explode at any given time. Called technician, paid $75 and said it was bearings and that it would probably did the same noise again even with fixing it, that Id be wasting my money!! Worth getting rid of it!! I just hate it!! I will never buy another Maytag again.

I have a Maytag front load washer, and it has been flashing codes since day one, smells like mold, does not spin water out, and at first, all Maytag could say is, Im using too much soap, the wrong soap, loading too full, and I have it on a stand that is sold with the washer that they dont recommend, after I paid $300.00 for it. Now, it is flashing an E3 code, and will not finish a cycle at all. Maytag wants money to fix the problem that thousands of consumers have, after paying over $1,000 for the machine. I will never purchase another Maytag product, for as long as I live.

We have had this washer/dryer stack up for about 2 years now. Not long after it was purchased from Best Buy, it started smelling like mold, even though we were doing everything possible to keep it ventilated. Best Buy employee said that service was not covered by the warranty that we purchased, so they suggested we YOUTUBE some ideas on how to get rid of the smell. They said it was a common complaint for front load washers. We have tried Affresh, hot water and bleach, hot water with vinegar and lavender, etc. Nothing is working. There is mold on the plastic inside the washer door and the stench is horrible now. You can smell it when you walk into our home. I believe that stench is the reason we are all having respiratory problems, allergies, etc. I just dont know what to do anymore. Really frustrating!! These appliances cost a lot of money.

I am a WWII vet. I bought a Maytag dishwasher 4 years ago from Home Depot... Cost me $600 in total repairs. Maytag would not help. My son just brought it to the dump! At that same time I bought a Maytag bottom freezer from Home Depot... It has never worked right. Ice dispenser broken after 1 year, food freezing in fridge at any temperature... It just died! Maytag refuses to take any responsibility for THIS POS!They should be ashamed at the way they treated me. I am 94 years old, and have fought for our freedom, and was looking for one simple thing from this American company. Its called fairness! Maytag sucks! You have lost a lifetime customer. You have lost my son as a customer, and will lose anyone I talk to, as well as my son posting on ALL social media! SHAME ON YOU MAYTAG! SHAME ON YOU MAYTAG!

The only complaint is the lights on the bottom quit working about a month after we purchased. It was nice to light up the stovetop when cooking. Now it’s slightly dark. I have gotten used to this. We spent about $8000 on all the matching Maytag appliances we purchased. I would love to replace all but not in the budget. I am a dissatisfied Maytag customer.

This so called high efficiency washing machine, and others like it are absolutely awful. They do not properly clean clothes. I frequently have to put loads of clothes through two or even three times in order to get things cleaned properly which our old washer did easily in one wash. That is the exact opposite of efficient. It is so bad that it actually borders on being a genuine scam. Do not buy! Huge waste of money.

The control panel died on this dishwasher (MDB7749) after only 2.5 years of light use. I was quoted about $250.00 plus labor to have the panel replaced. I will not fork over several hundred dollars for a defective panel, especially since many others have complained about repeated failures and known issues with the control panel. No more Maytag products for me. I plan to purchase a Bosch to replace it.

MF12665XEM7 Maytag Fridge water runs on the floor: After reading the review and watching the video to fix, I called Maytag. They refused to help. We bought our fridge at Nebraska Furniture Mart. We have spent a lot of money with them too. My husband called to see if they would split the cost of the service call. They refused. My floor is ruined from the water leakage onto it when we are not home. We try to catch the ice buildup and remove it before it is an issue. Why is there no class action suit? There is definitely a problem with this fridge and Im seeing it online everywhere I look.

We purchased a full house of Maytag appliances to support American Made (ourselves). It is very disappointing that our Maytag dishwasher Model # MBD 89595BW3 has completely quit functioning properly. All the lights came on and nothing worked after that. We contacted Maytag and was told to turn off the power and restart after 2 minutes which did absolutely nothing. No problem - try again. Again, nothing. The disappointment is compounded by the fact that this dishwasher is only 2 years 7 months old. It is too bad that an American Made product didnt last long enough to show any wear and tear. Investigation to repair resulted in cost prohibitive investment. So sorry Maytag, we gave it a shot. Moving on to a more reliable rated brand.

I bought this washer 2 years ago, it has always been noisy and not cleaned or rinsed my clothes very well. With dark clothes, I have to rinse them twice if not three times. Now it has quit throwing out the water all together and is not rinsing the clothes at all. Paid $72 for a repair man to hook it up to his computer and tell me there was nothing wrong with it. Told me it was how I was loading it. I dont think so. Now I have to replace a two-year old machine. I will buy a basic machine that only washes my clothes this time. Nothing is made to last these days.

Because it is the high efficiency model, need to leave the lid open so interior will dry and not smell musty. Also, recommend using a washer cleaner such as Affresh or Tide tablet every now and then. But works great!

I bought a Neptune washer and a dryer. I have had nothing but problems with these items since I got them. My washer keeps giving me a 3e code and will not clean the laundry right. I have used the H E detergent it requires and yet my clothes stink. My laundry smells like mold and mildew. I now dont have my units to wash and dry clothes. I paid almost $4,000.00 for the pair. I dont have the money now to replace them.