We owned the washer for 2 years and 2 days when we got a code F70. After searching online, I found hundreds, if not thousands, of reviews and self-help forums that show this product is in dire need of a recall. The problem I had is the motor control unit (MCU), which is a $225 to $275 part online. However, Maytag will only replace the board under extended warranty with a refurbished board that they say costs $330, whereas they say the new one is over $600. Why is it that Maytag charges double what everyone else charges? If so many people are having these problems, it is obviously a defect and should not be the consumer’s responsibility. It is obvious that this is too common of a problem.

Maytag MCT Washer & Dryer - I bought the largest capacity to save time. However even my 6ft tall husband has problems reaching the bottom to remove clothes. Even worse is the lack of water to clean clothes, washes so long it wears clothes and they are still dirty. I tried to improve on my old Neptune and Id love to have it back. I may have to junk this washer. The dryer is very slow. Buying this set was tossing my hard earned money in the trash.

The dishwasher is only one and a half years old and like many others are having trouble with the control panel. The model is MDB89495AWO which cost nearly $800. The dishwasher does not shutdown after an operating cycle. On contacting Maytag with the symptoms they advised that they have never heard of a similar problem. On reading the comments/experience of other Maytag owners I am undecided whether to scrap this unit and buy another make!

The Bravos XL MCT Maytag commercial Technology is not a good machine. I noticed it within the first few weeks. I called Conns to request technical support but the technician they sent didnt solve the problem. I also called Maytag, they also sent a technician. He told me the same thing as the other guy. To use good quality detergent and to make sure the clothes are neatly arrange around the drums walls. Nothing works. My clothes dont get clean because they dont get wet. Theres lots of residuals and wrinkles all over them. Also, the machine takes way too long to finish a load of clothes. I did tried to return it, but Conns wouldnt take it back. I dont recommend this washing machine at all!

Spent $2,000 on Maytag washer and dryer in September of 2020 thinking we were buying quality and a company that backs their products. Forward to January 2021 and were not able to schedule service through their website. Not able to get anyone to answer their phones. Called what used to be our local Maytag service and they told me Whirlpool took over Maytag warranty service and cancelled all the contracts for local repair shops. So, not only do we have a 4 month old washer I wish we had never bought, we cant even the Maytag to service it under their warranty! Never again...

I am so sorry to see so many people having the same problem. Maytag Dishwasher Model #MDB7749AWM2 purchased 12-10-11. Control Panel needs replaced (260.00...service call, part and labor). Writing this as Ive spent the last 20 mins on hold with Maytag. Im demanding them to make this right. Ive been told by Trisha at Maytag not to believe all these post as people tend to exaggerate the problems. Anybody have info on class action lawsuit? ?

I, like SO many other people, am experiencing problems with a relatively new Maytag dishwasher. Mine is Model MDBH979SAB1. I have owned the dishwasher for 4 years but use it 6 months of the year and, because I live alone, maybe twice a week. In effect, it has the equivalent of less than a year of normal use. My problem is the same as countless other people. I can tell from how it behaves that it needs a new control board. I find little comfort in the fact that I one of several thousand people experiencing a problem with a newer Maytag appliance. What concerns me, after reading many negative reviews and seeing Maytags response, is that Maytag does not seem to care. We need to get the word out. We need a massive boycott of Maytag. We need to hit them where it hurts: in their bottom line. Since they seem to be content to continue to put out defective products, the only way to protect consumers is to put Maytag out of business.

I have a major complaint with the Maytag double oven design. With the smaller oven above, if you spill any liquid while taking something out of the top oven, the liquid drips down between the two panes of glass on the lower oven door. This makes it impossible to clean. Maytags reply - call a service rep and have him make a house call and take the door apart for you and clean it. Not warranty work so I would have to do this every few months. Also, when baking in the upper oven, cakes and cookies tend to overcook on the bottom as the dishes are so close to the element.

I wish I would have read reviews before I purchased this washer, but I was in a hurry to get a new machine. Maytag has a great reputation and we went on that!! My Bravos is 2 months old and we have been away for a month! What a disappointment so far. What Ive noticed is all my dark items have residue on them, and today some of my light clothes came out looking like there is grease on them. Im afraid its going to wreck more clothes! Does anyone know if theres been recalls on the Bravos XL washing machines?

I have a MGDB850WR0 Maytag Dryer. I have had to replace the thermo sensor/heat sensor three times in the past three years. Dryer takes forever to dry. I spoke to the repairman who told me in confidence that his company receives a lot of calls about this specific dryer for the same reason. He said the part was originally made faulty and thats why it keeps going out. The part being the thermo sensor/heat sensor.

I have been very disappointed with the 2017 model of Maytag washer and dryer as the washer does not clean the clothes as it should. There is the inner part taken out with no agitator and I believe that is the reason that the clothes comes out not white or cleans as I am use to it being before with my other machines. I think they need to reinstall the agitator to clean the clothing thoroughly. The dryer takes longer to dry the clothing and it uses more hydro which cost a lot more monthly for us to have to pay out. I will never purchase another washer and dryer as this in the future.

DISHWASHER MDB7749AWM - We purchased this dishwasher from Home Depot on 10/15/2011 for $630.00 for my birthday and yesterday the start button stopped working (cycle lights still work). We went online to look for more troubleshooting options and we found lots of complaints about faulty control panels. Sounds like thats what we have. VERY disappointed in Maytag for not correcting known issue. My dishwasher is only 3.5 years old and there are only 2 adults in our home. We run the dishwasher 1 to 2 times per week meaning this Maytag dishwasher will only last for about 200 wash cycles. Shame on you Maytag!

Dryer wont dry/ service at dead end. So in 2018 we purchased a Maytag Bravos washer/dryer set. The washer does its job, it washes clothes acceptably. The dryer, which has the sole purpose of drying clothes, DOES NOT dry clothes. It leaves each and every load damp. Two to three cycles are required for even the lightest fabrics to dry. This has been the case since the product was new. After repeated attempts to have the dryer replaced, I am fed up with the whole run around. MORAL OF THE STORY IS DO NOT BUY MAYTAG.

We have had our Maytag dishwasher MDB9100AWQ only 5 years and now it keeps shutting off. I see there is plenty of this complaint. I will not purchase another Maytag product after reading all these reviews and experiencing it.

I bought Maytag frost-free refrigerator last August 2006. But now, I noticed that ice builds up in the freezer. The product is only five years old but I was told by Whirlpool that they had discontinued making defrost heater. The reason why I bought Maytag was the ad on TV showing the Maytag service technician seating and doing nothing, implying that Maytag brand is a good product. Think again before buying Maytag products.

Maytag Dishwasher Model MDB6759AWS3 Does Not Start - If you are having the following problem, here is what I did to fix it. All of the lights on the touch pad would light-up when pressed but the dishwasher would not start. It appears to be a corrosion problem on the connector from the touch pad to the control panel. 1. Turn off power to the dishwasher. 2. Remove the inside cover to the dishwasher door - approximately 10 screws. 3. Disconnect the electrical connections from the inside cover to the control panel still attached to the door. These are snap connectors. Always a good idea to label the connections before disconnecting in order to make sure everything goes back together properly. 4. Remove the black cover on the control panel. There are 3 screws. 5. Find the green conductor tape that connects the touch pad to the control panel. 6. You will remove the green conductor tape from the control panel. DONT just pull on it. There is a white piece of plastic that slides away from the control panel and toward the green conductor tape. It will remove pressure from the conductor tape and the conductor tape can then be disconnected from the control panel. 7. Get a good pencil eraser and clean off the exposed copper connectors in the conductor tape. 8. Place the conductor tape back into the control panel and slide the white plastic piece over it to reconnect the conductor tape to the control panel. 9. Replace cover on the control panel. 10. Reconnect the electrical connections from the inside cover to the control panel. 11. Place inside cover of the dishwasher over the proper screw holes - make sure the bottom of the inside cover is overlapping the bottom of the door - or the door wont shut properly. 12. Replace screws.13. Turn on power and check.It worked for me and saved me time waiting for a repairman and expense of the repair.

I bought a refrigerator from Home Depot in July 2013. In late November 2014, I noticed water on the floor in front of the fridge. I called the Maytag customer service and reported the problem.. The customer service rep explained to me that Maytag discovered a design flaw in the part that allows the water to drain when going through the defrost cycle. I also called Home Depot. Their response was it was my problem because the fridge was out of warranty and I did not buy an extended warranty plan. After two more calls to Maytag, they scheduled a service appointment. The service repairman told me the same thing about the design flaw. I have the old part and the package the new part was in. The two parts are completely different. I requested that Maytag or Home Depot replace the fridge or give me credit for the amount I spent. Maytag is now saying there was not a design flaw and because of that, Home Depot refuses to replace the appliance. I will never buy another Maytag product or shop at Home Depot. The extended warranty is a way to place the responsibility directly on the consumer and eliminating the responsibility of the manufacturer and the store.

Maytag bravo - thought it would be a good brand/buy/new technology. Absolutely nothing to like. Complete junk. Bought it in June 2013. Doesnt get things clean and takes a long time to not do that. We thought a good reputation from a major brand would mean a durable efficient washer with a reasonable capacity and good features. Unfortunately we didnt know when we bought it what a bad design/investment it was. It has destroyed numerous garments with fraying and doesnt rinse soap or dirt out because it doesnt use any water.The bravo from Maytag is supposed to be low water efficient. Unfortunately, it doesnt use enough water to wash clothes, no matter how little or how much HE soap you use. It frays clothes, leaves soap residue, wont wash jackets or blankets or bulky things, takes forever to NOT get things clean, doesnt get heavy stains or mud out, the list goes on and on.... oh, and its expensive, and breaks down a lot. I cannot believe that there has not been a government recall where the people who were unfortunate enough to buy one have been given a large amount of money back.

I bought a new Maytag French door refrigerator a few years ago and have been disappointed ever since. The quality is second rate and now the ice maker has failed. The product looks good but performs poorly. Buy a more quality foreign made product instead. Before this I had an LG which was quieter and never had a problem after 10 years.

Buyer Beware!! Purchased my Maytag over the range microwave in May of 2014. It has a manufacture date of Feb. 2014, and it is now Sept. 2014. It is a very nice looking unit but a bit oversized. My handyman that installed it had to raise my cabinets above my stove two inches to avoid it being too close to the range. The motor is pretty loud and It often times does not heat evenly. The light on the unit that shines down on the range is not much better than the power of a night light which is a bit disappointing considering it looks like a higher end unit, and down to the reason I am writing this review today is that for the first time I went to change the bulb. I unscrewed the the light cover which is placed awkwardly toward the very very back of the unit, only to find that when I went to twist out the burnt out bulb (that has been in there since I purchased the unit) that the bulb broke off after hearing what sounded like the break of a seal of glue, and the bottom aluminum piece of the bulb is stuck in the bulb socket. I found that the bulb is placed in an awkward place behind the light cover. Instead of the bulb facing to the left or the right or to the front of the unit it is facing toward the back which is making the bulb socket impossible to see, which means that in order to screw in the bulb you are screwing it in from an angle that you cannot see unless you climb on the range and lay on your back, or get a mirror to help see where you are screwing in the bulb. This is just a very awkward and unpractical design coming from such a well known company with such a common and ordinary product. Now I am sitting here writing this review and I am trying to figure out how I can remove that little piece of aluminum stuck in the light bulb socket and since it is not facing to the left or right and facing toward the back, it leaves me about less than 1/2 space to work with using my hand or a tool to remove that piece, or I can just leave my broken bulb piece in there and screw the cover back on until I call service for Maytag. I believe it is still under warranty but from others experience that I have read about I am not feeling confident I will receive great service or a desirable outcome. Wish me the best!! Thanks for listening!!

Bought this stove in 2011. 9 months ago I had a 300$ repair for fuses to two out of the five stove top burners. Several days ago the ovens were not lighting and I called for repair again. Well the ignition switch in the lower oven had a frayed wire from the factory which created an issue with the control panel. Today I was quoted 600$ to repair the ignition switch and the main control board. PARTS ONLY. I am not repairing this stove. Called Maytag due to the issue of a defective ignition switch wire and got nowhere. Very poor quality product.

I am retired and have always had dogs in my life. My recent purchase of a new Maytag top loading washer has been very frustrating. There is barely enough water to measure in an oversize tub. The placard on the lid, and in the owner manual clearly show three levels of water. Each load takes twice the time as I am used to with my older Kenmore washer. I am forced to cut my loads in two or three, and use more water and energy to do a job that used to take less than half the time, water and electricity. I have had warranty repair to replace the control board twice, but nothing has changed. The repair techs both said there is one program on new washers, the knobs and settings do nothing, and recommended I get used to it. They explained the EPA is responsible for all changes to Protect consumers from harm. WHAT???I wish I had never bought this unit - if I could get my Kenmore back I would, in a hot minute! What a waste of a large tub to properly wash pet bedding and bedspreads/pillows, when there is only 3-4 inches of water! I wasted an entire paycheck, when I could have gotten my other unit repaired or rebuilt. I am seriously frustrated, I am searching for an older washer unit to get back to doing my laundry without being forced into a laundromat for pet bedding and larger items!!!

The washer is designed to use low amounts of water. The top is glass so you can watch what is or is not happening. The manual states there should be clothes above the water after filling. However after the wash cycle with a full or even half full washer, there is still some dry clothes above the water. As a result the clothes are not washed until the rinse cycle. I called Maytag and a repair tech came out to fix it. His solution was to trick the sensors by dumping a pail of water on top of the dry clothes before starting the washer. The sensors think there are more clothes than there really is. Will never buy another Maytag or Whirlpool product again.

I bought the washer dryer combo. Dryer already broken. Washer is very loud when it changes gears. Would not recommend the washer or dryer.

Purchased the Neptune washer & dryer in 2002. Did not purchase any additional warranty. I have had Frigidaire, Kenmore and Speed Queen washers previously and used them until they quit. I have not had any problems with either the washer or dryer. No mold, no smell, nothing. I did laundry for 2 children and 2 adults, 6 to 8 loads per week with half being heavily soiled work clothes. I still wash 3-4 times a week. I was able to wash & dry king size blankets and comforters for the first time with this set. Washer and dryer are located on the main floor of house and are the quietest units I have ever owned. They may quit tomorrow, but they have done the job that they were designed to do. I am well satisfied with the quality and performance of both units and would not hesitate to purchase Maytag appliances again.

Maytag is supposed to be the best. I wanted a top loader again. This washer is almost worthless because of the water control. I have to add buckets of water before I start the washer. Otherwise the clothes are not clean. The cycles are strange with the amount of agitation. I will continue looking for an OLD model. DO NOT BUY THIS WASHER.

We purchased the Maytag Bravos XL Washer and Dryer based on the good reviews. This has been the worst appliance purchase we have ever made. The washer had to be replaced on the 3rd day after it was installed due to a motherboard issue. The washer constantly has the UL error code so I cannot leave the house if I am going to wash any clothes - I readjust all the clothing in the washer; however, there is no rhyme or reason to the UL code - just made workmanship.We also have had many issues with the dryer as well. Our clothes stopped drying, the clothes had a mildew smell and the lint was wet even though we religiously clean out the lint element. We researched and found this was a common issue. The belt comes off on these dryers; apparently it happens quite often. We fixed it ourselves - twice- by watching a YouTube video. Now our dryer catch (latch) doesnt work and we have to repair that as well.It is obvious from all the complaints that both of these Maytag machines that there should be a class action lawsuit at this point in time. I will NEVER purchase a Maytag or Whirlpool product - EVER. Whenever anyone asks me for a recommendation I tell them to stay FAR FAR away from both Maytag and Whirlpool products since they are unreliable, have terrible workmanship and the company will not do the right thing and fix the issue and provide refunds to those that have purchased these terrible machines. A washer and dryer is a big investment and should last more than a couple of years. I never had issues with my Kenmore or GE products and wish I still had them. DO NOT PURCHASE ANY PRODUCTS MANUFACTURED BY MAYTAG OR WHIRLPOOL. EVER.

I bought a Maytag Centennial HD washer and dryer. I have had no issues with the dryer but the washer is absolutely junk. I’ve had it 5 months and this is the second time it’s stopped spinning and I’m dipping my wet clothes out. Not only does it cost hundreds to fix it, it doesn’t wash well AT ALL. Your clothes still come out with deodorant stains and spots. It’s a complete waste of money and time. Run as fast and as far away from this worthless machine as possible.

When purchasing a microwave for our kitchen the Maytag MMV4203DB00 had all the functions I wanted. Just after a year its quite cooking. The fan would still run but not heat anything. I called Maytag and was told basically, tough luck. I said something about Maytag, that it was supposed to be a great brand and should last longer than 1 year. The part to fix it plus labor was going to cost nearly as much as a new microwave to replace it. Now, the microwave has started to turn on by itself. Customer service was very rude and came off with a we dont really care attitude. I will never buy Maytag again.

Maytag is the worst washer company. I owned my washer for two years and I had two different problems with it and now I have a 3rd. The first was the same day they delivered the washer, I needed a wire harness. I should have returned it then but I didnt. The 2nd was six months after the first one. A wire came loose due to the washer shaking and the 3rd, Im not sure why it wont drain but the tub is full of water. I called Maytag and they really didnt care as long as they got their money. They referred me to three companies that fixes washer. Two of three was already out for this washer. If I didnt know any better I would think Maytag gets paid off for every customer they referred to these companies. I would never buy another Maytag Bravo or Whirlpool product. Im very dissatisfied with their Bravo washers. They lost a long time customer.

Im not sure that the guys who designed this unit ever actually tested it. During the wash cycle, if you have something like a fitted sheet it will actually stuff all of the surrounding wash items into the sheet until it forms one huge, round ball. Then it gets really interesting because the vicious spin cycle sends the machine marching around the laundry room and this happens even if the wash has not balled up. I now try to evenly distribute the wash within the tub prior to starting the wash cycle but it doesnt work. So now I grab a cup of coffee and newspaper and sit with my washer throughout the entire spin cycle to make sure that the hoses dont tear out of the wall.

Purchase in April 2010 on 12/31, motor and computer panel went out, not washing. I do not recommend this dishwasher cost to repair. Too expensive.

Maytag Model #MGR7662 range - We inherited this oven when we bought my mother-in-laws house 2 years ago. We had to get a thermometer to keep in the oven since the temperature is never consistent and is usually 50-100 degrees lower than the digital readout. We will be replacing this oven as soon as we can and it will NOT be a Maytag.

I purchase my Maytag electric glass top stove 9 years ago. 2 years ago, one of the burners went out and had to be replaced. Now, in the past 2 days, my oven is taking FOREVER to preheat from 0 to 455 degrees. So far, its been 78 minutes waiting for it to go from 0 degrees to 425! Apparently the heating element is defective. As far as the self cleaning oven, it is absolutely worthless, and does NOT work! Needless to say that Im very disappointed, and looking at another repair expense!

This Maytag was installed in this house in the summer of 1984 and washed dishes for my in-laws for 26 years. We moved in as a family of four and this Maytag dishwasher is still washing the dishes clean. No rinsing, just make sure the food is gone. We replaced the belt about 6 years ago and I think my Mother-in-law replaced the door seal. It has a power saver button, 2 cycles, and the cups are on the bottom rack, plates and such on the top. I dont put plastic bowls on the bottom because it gets a bit too warm for them but all the bells and whistles still work. It is a fairly large model, WU301, with ample room for plates and platters. I dont wash pots because I dont like what the dishwasher soap does to the finish on them. Having the cups on the bottom is nice and the rack is very usable for other dishes as well. The cutlery rack is located on the top rack, removable and a decent size. Almond body, silver and dark brown accents, very 1984 but not a bad look. All of the buttons and knobs are easy to read and use. Maytag, 1984, model #WU301.

Bravos XL Like so many others Ive read, this is a terrible product. Washer constantly goes off on unbalanced load. After 14 months, the plastic tub disintegrated. Maytag tried to sell me the service and extend a warranty for $300 also. Just like all the other reviews. Wow, has Maytag gone downhill.

I just want to give an update on my frustration with Maytag dishwasher I wrote about on July 16. In the end, I found a DIY solution and fixed it. I wrote an instructables here: **. Not recommended if you dont feel comfortable repairing things. However, the diagnostic test at least can give you some clue whether its the control panel or control board is at fault before replacing both. Thanks.

I bought this dryer 3 years ago and the fuse has blown three times. The dryer gets really hot and blows a fuse. The entire back of the dryer is clean and free of lint, the hose on the back, and the ventilation pipe running out of the house are completely clear, but the dryer continues breaking down. The Whirlpool NC folks have been out here three times yet it has broken down once again. I should not have to purchase another dryer after only three years!

I feel its kind of cheap. The interior is all plastic which doesnt look shiny and clean as it use to be when it was new. Not efficient in cleaning. Can see still dirt spots in some of the washed dishes.

We bought a Maytag Bravos three and a half years ago. We always tried to follow instructions for the machine. Only used he detergent, used the affresh, tried not to overload the machine etc. Had to call a repairman. Our washing machine started leaking water at the bottom. Hoping that it is only a three machine it would be fixable. Bad news the repairs would be over $600.00. It needs a new tub seal and bearings. For a THREE YEAR OLD washing machine! The repairman and I had quite a talk about appliances. He said they just dont make them to last anymore and the companies such as Whirlpool, Maytag, etc. do on purpose and they get away with it. Stay away from Maytag Bravos. It is a worthless piece of crap. It will not last long. Now we have a three year old washing machine that does NOT work right. Something has to be done in this country to come down hard on the companies that make appliances. I would NOT recommend this piece of crap of a washing machine.

This is my THIRD dishwasher, and by far the best. The Bosch machine I had before that was a catastrophe: mediocre cleaning, intense filter cleaning required - at least every two days - and, with a pretended noise level of 47 dB, MUCH noisier than the 50 dB announced by Maytag. Somebody is laughing at someone! To sum up: the Maytag MDB4949SHZ cleans dishes incredibly well, is very silent and requires no filter cleaning.

Washer needs new transmission at only 3 years old! Maytags 10 year part replacement doesnt cover it. The company actually asked why I didnt purchase extended warranty, I thought I didnt need one. Bad bearings, it doesnt wash the clothes clean, $400 to fix it. Needless to say Im buying a new washer and it will not be a Maytag, worthless piece of scrap!

Maytag Bravos washer MVWB750WQO frame assembly and cabinet rust - I sent letter of internal and external rust issues to Jeff Fettig (Whirlpool CEO) and received no response. Then, I sent letter a second time with an attached signed receipt. Then, I finally received a call from corporate staff member stating they would replace parts but not labor. Labor costs would cost between $350 - $500.00. This is without the initial service call and diagnosis cost between $100 - $125.00. The determined parts list cost would be $700 - 50% for Whirlpool internal cost + shipping be approximately $425.00. This is more than the cost of a new unit or the value of three-year depreciation value of the existing unit. This does not make any financial sense. Whirlpool should provide a new replacement unit at their costs. It has been three months and with no successful outcome. Also, via web research, there are many complaints about Maytag/Whirlpool and I am not the first in regards to rust issue. Therefore, Whirlpool is attempting to limit their financial exposure by only offering parts that they have to agree upon because the labor costs will not support this additional investment in a three-year unit. It makes more financial sense to purchase new or be offered a replacement unit.

My experience over the past 2 years with my top loading Maytag washer is echoed in almost every review here. 1. Not enough water to clean the clothes 2. Clothes come out still dirty and covered with detergent 3. Barely agitates 4. Repeated repairs for leaking and computer board breakdown 5. Complete lack of interest by either Lowe’s and Maytag when contacted. I could write a long, detailed complaint but it has all been said quite well. We need to band together and file a class action lawsuit against Maytag. Any lawyers out there willing to take this on?

We bought this range (model MER8700DS 1) March 25, 2015. Manual states when you use the oven first few times odor or smoke may happen and is normal. It also tells you this is not harmful but remove birds to another room because the fumes can kill them. Noxious fumes? Forget about the birds! Had to open up the whole house and go outside. Burned my eyes, throat and lungs. Day after day, repeatedly turned temp up to 400 trying to burn off what we thought might be a coating. No luck.Maytag got very concerned when I explained about the noxious fumes and had someone come out right away. Tech took it apart. He removed bottom (screwed in) plate that covers the bottom heating element. That plate gives the added ability to have 3 racks and make full use of the 6.3 cubic ft. capacity. Under the plate we found bits of insulation. We think that is what we smelt as it burnt up. He couldnt smell anything when he had it up to 400. So off he went thinking problem solved. Well, it still stinks. We will have Home Depot take it back. Oven takes forever to come to temp which we read in many complaints but thought thats minor. Dont know what oven to get instead since Whirlpool makes so many brand names. And other brands all seem to have their own problems.

This is the second Maytag appliance in less than 5 years to stop working. The first was a dishwasher. I got 14 months use out of before the control panel burned out. Fixed it for $125 only to have it happen again in 6 months and repair company said parts are only 3 months warranty. Cost me $5 to bring to landfill. Now the matching Refrigerator is making a loud humming noise and Ive been told its the compressor.

The refrigerator has been very dependable for over 14 years. The biggest problem we have had is failure of plastic tracks on drawers that break and had to replace drawers and other problems with plastic components like deli drawer coverlet, and door shelf door plastic. Recently we have problems with the touch control panel on front of door. Not working properly for ice dispensing and temp. control although temp is maintaining what we had set prior to failure of control panel.

Fridge Model MFF2258VEB6 - Our refrigerator is less that 2 years old and it wont make ice! The bottom of freezer is filled with water that froze. Everyday there is water on the floor. We asked at Home Depot where we purchased it and they said we need to change the filter. What filter? The owners manual is a joke. We cant figure out where the filter is located so it looks like we have to pay money to have someone come look at this. Hey, this is ridiculous. I thought Maytag had a good reputation and thats why we bought ALL Maytag appliances two years ago! Never again!

Washer exactly 3 months old, will not work. Maytag can tell you nothing, they just want your money. They called a repair service in our area, never heard from them. Here we sit no way to wash clothes. And they say will charge to fix it. WHAT IS WRONG WITH THIS PICTURE. FO NOT BUT MAYTAG ANYTHING.

Bought this Maytag microwave mmv 4205ds March 2016. Have had open/close problems five times in 3 years. Unit replaced under warranty once. Now out of warranty. No need to mention inconveniences we’ve been through. Whirlpool-Maytag obviously have done nothing to correct this problem. I will never buy any of their product again. Wanted to give them ‘0’ stars but program won’t allow me.

Our Maytag dishwasher is a work horse. Never a problem just runs and runs. Could be a little quiet quieter. But does a t great job cleaning. I would definitely buy another one and would recommend it to any one.

We bought top load washer model # MVWC425BW1 at Lowes brand new 9/22/14 for $493.93. On 11/23/2017 it stopped working and would not even come on after lid locked. Found out it needed new parts that would cost us over $300 to fix and we could buy another new washer for $400. We are very disappointed that this washer with only two people only worked three years when we thought we had bought a reliable product that would last. Sent several messages in November but no response till today 12/13/17 after filing. BBB complaint filed and they decline to do anything. So this company just wants to sell products but has no customer service. They only give a year warranty. Of course if the product is not going to last they want you to buy more.

Preheat the oven, put in the food. Oven does not maintain the temperature. Gives me a code of F2-3. Want to know what part needs replaced to solve this problem. If anyone can relate to this problem or help me with information please respond to this or email me.

Bought this as W/D set brand new from Home Depot. Had been noticing incredible wear and tear on clothes, as things get so tangled up and need to be practically ripped apart before going into dryer. Cycle times are crazy long, up to over an hour in some cases. Doesn’t have a “Speed Wash” cycle. But WORST of all, after less than 3 years, it just stopped draining properly. Tried all the Codes test, etc. Finally called a repairman just to be told repair costs would probably cost more than the machine is worth. $125 to be told we ought to just buy a new washer. Not happy.

I have a top loader Maytag washing machine, Model MVWB835DW4, bought in 11/2019. Five months of light use, the lid cracked. Received a replacement and four months later the lid once again cracked in the exact same spot. Requested replacement parts under warranty and I was told that a service tech must install the lid. Due to health and safety concerns related to Covid, we are not take any chances letting people into our home. My wife and I are 70 years old and are at high risk. Maytags response was they would not send parts under warranty to me and a service tech must install the parts. If I dont let them in by 11/2/2020 (the end of the warranty period) then I would have to pay for the parts. Maytag has the very worse customer service in the industry.

Purchased a new Maytag washer (MAH5500BWW) and matching dryer along with the pedestal that they sit on in late November of 2003. Spent well over $1900.00 for everything including the delivery charge. I noticed the build up of mold/mildew inside the washer starting in early 2005 but cleaned it every week or so and it seemed to go away. As time went along the mold/mildew smell got stronger even after each cleaning that I did with bleach. Nothing seemed to help.It wasnt until 3 days ago when I had my dryer vent cleaned by a professional company that the technician looked over at the washer and said You know that washer was recalled and that there was a class action lawsuit against Maytag about mold/mildew issues involving that model. He opened up the washer door and looked and was shocked. He told me that he himself had the same Maytag model washer and was notified by Maytag years ago about the class action lawsuit. He told me that he had received what he called a buy back check from Maytag. I wondered why I had not been notified since I had purchased both units new and registered both with Maytag after my purchase.I decided to do a search for my washer model number and looked for mold/mildew issues and was shocked to find thousands of complaints involving this issue with this model of washer. I then called Maytag/Whirlpool and this is where the fun begins. I called and explained to the customer service rep at Maytag/Whirlpool what the problem was with my washer and asked her why I was never notified of any recall or class action lawsuit involving my washer. After thinking for a minute or two she says that she is unaware of any problems with my model of washer and asked me to recheck my model number. I do this and again she says that she is unaware of any problems associated with my washer. I explain to her about the thousands of complaints on the internet about this mold/mildew problem and she then says I shouldnt believe everything I read on the internet.At this point I ask to speak to her supervisor which she says she transfers me to and the fun continues. The supervisor then tells me that the customer service rep whom I was speaking with is new and doesnt remember the issues with my model of Maytag washer but she herself does remember the issue of mold/mildew build up inside the washer. I ask her why wouldnt this issue of mold/mildew in this washer be in your system for this rep to be able to refer to? She then says that since this issue was so long ago its not in their system anymore. Huh???She asks me if I was part of the class action lawsuit involving this washer and I explain to her that I was never notified of any such lawsuit so I couldnt have been part of it. She then says that Maytag has since settled this issue long ago and since I missed signing up for the class action lawsuit I was just out of luck. Somehow its now my fault for them not notifying me about the class action lawsuit years ago!She then offers to send out a repair person to look at my washer and to look at the mold/mildew problem. I ask her if the service call was free and she snickered and said no, why would it be free? I tell her I thought it should be free because I paid nearly $2000.00 for these machines because I was looking to get the top of the line machines. Now I have a mold/mildew infested Maytag washer that smells and looks so bad its a assumed health risk. She again tells me that the service call will not be free and asks if I want her to schedule it now. I quickly decline!She then tries explain to me in some odd fashion that I should be happy that I got 10 years of service from my washer/dryer and hoped that I would continue to purchase Maytag. What??? Are you crazy woman!? Now its me who is laughing at this point. I almost say some very bad things to her but better judgment takes hold and I just hang up. Now you have heard my story and Im now looking for another washer/dryer so I can remove this health hazard from my home. I will never ever buy anything that has a Maytag/Whirlpool named attached to it.

First Maytag washer we bought in 2003, worked flawlessly for 14 years, bought a new one in 2017 only because my wife wanted a bigger washer. Bought a Maytag top load MVWB765FW0. What a big mistake. In less than 3 years it has failed already. The water inlet valve went bad. Maytag offers no tech support because they want to charge you with a service call. I found out what was wrong by researching the problem and error code online and bought the part for $55.00 and fixed myself instead of them charging $100.00 just to show up at your door plus the part and labor. A washer failing in less than 3 years is totally unacceptable and I will never purchase another Maytag/Whirlpool product ever again. Someone needs to wake up at Maytag.

After only about a year or so - and it is out of warranty - the clothes are not clean - there are white type of scum marks left on clothes and especially dark clothes. This is even after I use the recommended detergent and less than normal and do a double rinse. Have to wash clothes again with no detergent with a double rinse again. Just so annoying. Would never buy Maytag again.

You get what you pay for, you can go cheaper with no frills and watch how clothes wash, also run afresh through the washer as recommended. Also use the correct amount of detergent. Maytag isnt as good as it once was but it is the top of Whirlpools line of companies.

IT A GOOD DISHWASHER, BUT I HAVE HAD 2 PROBLEMS WITH THE CONTROLS AND HAD THE CONTROL PANEL REPLACED. TWICE. The insurance I bought with the machine, sent me a jerk to fix it, I complained and they sent a good repairman.

Range is at least 20 years old and everything still works w/o issues. Our model has an upper level and a larger lower level that is a convection oven also. The top one heats up real fast which is great for quickly cooking and reheating. The lower one is large enough for everything else.

In 2011, I purchased 2 Maytag dishwashers, one for my tenant and one for myself. In 2014, the circuit board on my tenants dishwasher failed, when the unit was only 3 years old and of course out of warranty. I first contacted a local repair person, and he informed me that the repair plus service would be close to $300. When I contacted the company, after about an hour on the phone, they agreed to send their authorized repair service person and after his evaluation, would repair the unit with no charge to me, as a courtesy. This whole process took about 2-3 weeks. I felt that was fair. It is now 2015, and my unit, which I purchased at the same time and the same type, now is not working due to a faulty circuit board. My tenant uses her dishwasher more frequently, and that is most likely why her circuit board went first. This is a design flaw, or perhaps planned obsolescence. At any rate, Im not happy with this, and my model is mdb7809awb2, and serial # is FO4205659. Do you know if there have been any other complaints on this? Thank you for your help.Updated on 07/30/2015: After I wrote my review, I contacted Maytag about the problem. After considerable wait times, I spoke to someone who set up a diagnostic repair call, giving me the impression that Maytag would cover it. When the repair company called, they told me that I would be charged $104.95 just for diagnostics. Labor and parts would be additional. I called Maytag again, and they agreed to let the repair company charge back the diagnostic fee. After diagnosing the problem, it was determined the problem was the control panel and not the circuit board. The cost to repair with tax came to $315.85 and it was only this low because the repair company waived the return service trip. I can get a new dishwasher for a little over $400.00. I am very disappointed in Maytag, because I remember the commercials where the Maytag repair man was bored because the products were so dependable they never broke. My unit is only 4 years old, and its sad that it costs so much to repair it.

We were excited to finally buy a new wash set and I always wanted the Neptune ones. I had owned a Maytag for 25 years through two children and a mechanic husband. I had every confidence in the new ones and expected at least the same service. Shortly after the warranty went, the machines both started to act up. The washer would stop in the middle of the cycles. The dryer wouldnt come on or wouldnt respond to the commands. We finally contacted the local repairman whom we have used for years. He came and gave us boo-hoos about these machines. He said they were trouble and we should have never have bought them. My husband figured it was the electronics in the control panel. The repairman said the parts would cost somewhere near $500.00 to $600.00 each and proceeded to try to sell us used ones for $2,000.00. We said we would try to get the bad parts and he even gave us the stock numbers? We went online and found new ones for half the price. We bought them and put them in and they persisted in doing the same things as before. Is this a runaround or what? Who is bilking who? Another great American rip-off. What can the public do?

Products spoiling even if set at recommended temperature. Hard to clean bottom freezer. Not happy with this configuration. Had to have repairmen in because of stopped up drain which I could not access to clean myself. Does not close completely at times.

3 years into the buying of a Maytag Bravos XL MCT washing machine (Serial # **) and already had to replace the original control panel for a cost of $400+ in less than 2 years of the buy. Now AGAIN the replaced control panel is now once again shot and the machine is not starting. The appliance needs to have a #manufacturers recall for the control panel. #Maytag #Whirpool #BetterBusinessBureau Note -- all existing customers, please lodge manufacturers complaint for the control panel issues @ 1-800-344-1274. (Even if you dont pay because of extended warranty or plan coverage, if you are facing the control panel issue year on year). All future customers, buy this appliance at your own risk.

Our Maytag Dishwasher, Model MDB4949SDE2 was purchased May 14, 2016 at Home Depot for $470. It has performed perfectly until January 6, 2020, when a noise, loud enough to imitate grinding wheel, happened with every Start-Up attempt. An independent technician advised replacing the pump motor, thinking that perhaps some popcorn kernels had lodged in the system. (Kernels were cleaned out of the drain filter.)We operated the unit after he left, and the noise began to diminish, eventually disappearing altogether after several loads. Today, February 26, 2020, the same tech found that the large, upper impeller was clogged (not rinsing completely) with citrus seeds and VARIOUS METAL SHAVINGS & SMALL PIECES OF WHAT WOULD BE CHOPPER BLADES FROM THE INTERNAL GARBAGE DISPOSAL. After reading the Maytag Dishwasher problems experienced by others (with repeated control panel failure, burning wires, leaks, and house fires), I consider us lucky to have none of those. We will not run the unit at night, nor with an empty house. Next problem, we will buy a Chinese made dishwasher, like GE.

We purchased a 3K Maytag refrigerator/freezer and purchased an extended warranty as well. 5 months later the ice machine stopped working. We called Maytag to get it repaired since its under the 1 yr factory warranty and they sent an appliance service company they contract with to repair it. 6 service calls and two months later its still not repaired. I called Maytag back to say if you cant fix it please replace it. They say it needs to be deemed not repairable to even consider replacement and that they would send out a different repair company. As of yesterday (9/(9/14) another month and a half and 5 trips from the second repair company and it still does not work, so I call Maytag again to complain and they give me the same line ....needs to be deemed unrepairable... How long and how many service calls does it take to fix a ice maker? How much work and how many hours do I need to miss to get what I paid for? I went to their website and it talks about how their mission statement is customer service etc, etc, etc..... Thats just a bunch of lip service and judging by the HUNDREDS of complaints I have read this is their standard method of operation.... I for one will not let this go and will be filing a claim in small claims court to get what I paid for..... BE WARNED if you are looking to purchase a appliance.

Around three years ago, my wife and I bought a top loading Maytag washing machine. It worked fine at first but later on, my wife would constantly find socks at the bottom of the machine after the washing machine was done. The last straw was when another sock plugged up the pump and had to buy a new washing today on 12/29/15. My wife told me tonight that the serviceman told her that they were getting similar complaints from other people who were having that same problem with this particular washing machine made by Maytag. If I knew that Maytag knew that there was a problem with this particular washing machine of theirs that I would never had bought another washing machine from Maytag on 12/29/15 at all. I wish that Maytag would stand behind their product instead of selling this defective product to unknowing customers like me and countless others who thought they were buying a top notch washing machine from Maytag.

I, too, am absolutely done with ANYthing Maytag. We purchased our Maytag microwave model MMV4205DS-1 in January of 2016. Within the first year we experienced occasional open/close door issues due to the faulty door latch switches. Now it happens virtually all of the time. The ten year warranty is a joke; it is just a come-on designed to deliver a false sense of security that Maytag will indeed stand behind their worthless products when in fact they wont. I am so disgusted with them.

Purchased a Maytag Centennial top load washer that will not fill with enough water to wash clothes. The washer was purchased from Lowes on August 17, 2016 and we tried to return but Lowes refused because we were passed the required 30 day return period. We contacted the Maytag company and they sent out service people who reported that there was nothing we could do other than wash small loads. The company also reported that if we tried any of the solutions on the web we would violate our Warranty. Since we find ourselves in this spot (we should have read all the bad reviews here before the purchase) we have decided to place the machine in a very visible spot across from a new 100 store shopping center on a truck with a 4x8 sign warning the public not to purchase this product.

Purchased a Maytag Dryer, Washer and Oven Range in December 2011. Both washer and oven were serviced within 1 year under warranty. The dryer stopped working in August 2013, not under warranty. Total cost to repair is $450. Called Maytag to see if they could reduce the repair cost, answer... NO. Maytag spends millions of dollars in advertising... Built Strong to Last Long but they cant spend several hundreds to keep customers. Will never buy a Maytag, Whirlpool, KitchenAid or any other related company product ever. Their motto should be Built Weak to Last Weeks.

I purchased an expensive Maytag washer & dryer, top loading, energy efficient, only to find it now shreds all of my towels, robes, dress, undies etc. Maytag reply was to put things like undies, t-shirts, & dresses in bags to wash... What about towels? I had an expensive white Terry cloth robe from Neiman Marcus which is now shredded, Im showing it to everyone. Plus the dryer has an area above the front door that snags everything. I open the door & clothing is hanging there, caught on this area. Tell everyone not to buy Maytag, theyre rip-off. Ive lost more money on ruined clothes & linens than the trash washer & dryer are worth, but Im disabled, handicapped, 61 yr old who cant afford to buy another new washer!

I just purchased this washer in Feb. 2012. The motor had gone out in Oct. I called Maytag Service, they came out to repair it. In Nov., it was doing the same thing again. I called Maytag Service, and they sent someone out to fix it. They expected me to take off from work where they inconvenience me with this washer. It is a reject washer. They would give me another washer and not consider people having to work and cant take off for their reject washer. They said as long as it is under warranty. I feel that I should be able to get me another. This washer has given me problems since I had it.

I purchased a Bravo 300 MVWB400VQ in 2009. I knew in 6 months that I had made a huge mistake. The clothes began coming out soaking wet - the dark clothes have lint, pet hair, and rings on them. The large capacity drum is just that... a big drum. If I wash bedding in it, it becomes off balance and sounds like its fallen over. I have used only HE detergents, and I wash the washer (yes, wash the washer, does that tell you anything?) before the light comes on. Now the machine sounds like its full of loose parts or rocks in it when it begins to fill up. Its even worse when the water starts to pump out. Now that Ive read all the other complaints, I realize that Im doomed. All of these trusting people have been cheated out of nearly a thousand dollars for a piece of junk. What good is Consumer Affairs if there is nothing done when there are so many complaints? I will join any lawsuit against Maytag if ever there is one. This is another lemon that promised everything and delivered nothing.

Purchased this washer at the end of August and it was delivered the first week of September. On September 27th the rubber seal around the door somehow got tangled in with a shirt and was ripped off (absolutely no idea how that even could have happened) and spilled water all over the floor. I called Maytag on Sept 27 and they had a tech out here by October 2nd which was great. However, even though I had told them the problem and that the rubber seal was damaged the tech didnt bring one when he came. I had to call them last week to find out what was going on - they had the tech call me and he said that the part had just shipped and he should have it by next week - Today, I had to call again as there was no follow-up from the tech and was told that hopefully the tech will come on October 21st once he gets the part as he hasnt received it yet. I regret purchasing Maytag, as I had heard they had better service (local techs/parts warehouses) than LG or Samsung but that doesnt appear to be the case. 3 Weeks to repair a $1400 washer that I used for about 4 weeks is unacceptable. On top of the inconvenience Ive had to spend $40+ dollars a week at a laundry mat, plus waste my time. One star service.

I bought this washer from Home Depot and was told I could load large comforters and even sleeping bags in it because there was no center agitator. There NEVER seems to be enough water to wash and rinse clothes completely. The water saver feature cannot be used as I have to use extra rinse cycle EVERY load to rinse soap out of clothes or I get white residue spots. I have MANY MANY shirts that have small tears in them I believe caused by this washer. I have monitored shirts I put in the washer and again today lost another high quality fabric T shirt. I have saved all of the shirts in hopes that one day there will be a definitive report that this washer design stresses clothes and damages them. I am going to purchase a new washer and it will not be a model like this.

Worse washer ever, clothes are dirty and smelly. Customer Service is even worse. After a normal cycle clothes come out half wet, never enough water in the machine. Everything gets washed on bulky and there is soap residue on everything. Have taken clothes to the laundromat on several occasions just to get them clean. I cant wait to get rid of this piece of crap!!! Never ever buying Maytag again!! Warning to everyone... DO NOT BUY THIS MACHINE!! And with the extended warranty, they still dont cover it. :(

I thought it was just my machine that sounded like an airplane taking off in my laundry room. Upon reading these reviews I see there is a real problem with this machine. My parents and grandparents trusted and swore by Maytag products. Maybe then, but certainly not now. Maytag for me stands for landfill. I have had 2 Maytag certified service companies come to repair my washer that is only 6 years old and its the same part both times which I am told by these service providers has been a problem and Maytag knows about it. But when I call Maytag all I get is some sound bite advising me there has been no recall and since I have an extended warranty I will have to take it up with them since that is who my contract is with. Of course they are only obligated to make a repair and cannot replace a defective unit. Of course not.Far be it for Maytag to step up and really stand behind the promises they are making all over our television channels with the new Maytag man. The top of the washer is also all rusted out around the soap, bleach, and softener openings. It is a poorly made machine with known issues by a manufacturer that I will never buy from again. Its a sad day that manufacturers are not held accountable for inferior products and even sadder that this Maytag manufacturer boasts its made in the USA for this machine. So is it back to China we go??? If you want America back you better support your product to your buyers.

I have Maytag Model MGT8885XS03 Gas Range. I bought it in 2014. The surface burner valves, which regulate the gas flow, are a bad design. One valve got stuck and needed replacement within warranty. Then another valve got stuck about a year ago and the third one got stuck about a month ago. I am going to replace these two valves now. My friend, who is helping me replace, has similar gas range. He also needs to replace a valve. His range is about a year old.

Our refrigerator is just 2 years old and it have been leaking for over a year. It started leaking right when the warranty expired. I am so mad. I called them and they said... You can purchase a warranty for $400. I am like.... what!!! I called my home warranty and they fixed it for $100. A few months later it is leaking again! I am so mad... It is a $1200 refrigerator. What can we do as a group to fight for this? There have to be something that we can do?? It is so frustrating. If there is an attorney that can take care of this group that would be great.

I also am the unfortunate owner of a Maytag dishwasher Quiet Series 300. I bought it in April 2006. The control panel has been a problem since the first year of operation. Typically, one of the indicator lights would randomly go on and off during the machines off mode. At other times, the control panel would not operate. However, if I waited a few hours, it would dry out, enough and then would operate. Apparently, steam leaks into the control panel and causes it to be erratic. This has been a problem with this design for many years and the Maytag Corporation has not cared enough about its customers to correct the design flaw. I remember when the name Maytag indicated a top of the line product. Sadly, this is no longer the case. As a result, my loyalty to them has ceased.I probably will not buy another Maytag product again. Their standards have eroded.

I have used Maytag washer and dryer for over 20 yrs. I recently replaced the set we purchased in 1988 because the washer broke down but I have never had a great problem with it either. I do on a average of 3 loads of laundry a week. I measure my detergents, mostly wash on warm or cold and I keep the filters and machines clean. I would buy the same maker should I need to replace them.

Love, love this washer. Does an amazing job cleaning colors, whites, and bulky bedding. If you like Tide Pods or other liquid pacs, this might not be the washer for you as they tend to end up inside the gasket. Powder-filled pacs are no problem however.

Top rack fell off with load of dishes. Clips that hold rack to slides broke. Week for repairman, two days for parts, week for repairman. No repairman, call parts be in on 7/28 2014, repairman on 7/31/2014. ONLY HAD DISHER FOR A WEEK, NOW IT IS BROKE. WHAT A RIPOFF.

Convenience, small, clean while you doing other jobs, it cleans while you sleeping, it's not loud, not expensive, comes in different sizes and colors, it's another helping hand, you will love it, it's worth the money.

As all the other reviews day 1 Dryer had no heat, washer unbalanced and knotting all the clothes. Sent out new dryer after trying to fix to no avail. One month after new dryer, normal cycle continues to run and not turn off. Repairs again - new computer board. Now washer is winding high pitch noise level - repair new bearings. Thank goodness for warranty. But washer and dryer act up again. I purchased extended warranty. Washer tub needed replacing because transmission went out, dryer again control panel problems. Last night the dryer started on FIRE. I’m sure because the control panel normal was not working again after it was replaced less than 2 yrs ago. Total time owned 6 miserable years. Going back to basics, ugh....

Maytag model #MDB6949SC, purchased Feb 22, 2015. In early May plastic parts from the top rack wheel assembly broke. Assembly unit replaced at no cost through the 1 year warranty. (cost = time and effort to arrange replacement with repair person). Same parts broke again in November - replaced at no cost again under warranty. Warranty expires in two months. If past performance indicates future performance, this part will need replacing twice a year at ~$140 per visit or $280 per year. Not a good thing. Called Whirlpool and with several calls and emails. They offered an extension of a year on the warranty. I think using plastic for this wheel assembly unit is a design flaw. Would not recommend this dishwasher.

I was in my bed and lights and TV flickered. Then, I heard a small explosion and my dogs went crazy. I went into the kitchen and my Maytag Gemini stove was smoking and smells really bad. I unplugged it. The sockets and the one close to it no longer work. My house stinks now. What happened? I have had this stove for a few years but it is not used often except during the holidays.

Weve had this washer for five months now and really regret buying it. It cannot remove even minor stains and often leaves residue on clothes, even with extra rinsing. I spilled coffee on some fleece pajamas and it took four washings to get the smell out.

My husband and I purchased this Maytag bravo washer in May 2014. It is not even three years old and the bearings went out. Call the repair man and it would cost over $300 to have it fixed. I paid a lot of money for this washer, expected it to last more than less than a little than three years and I think its terrible. Its loud, water was leaking all over the floor, its just a terrible terrible washer. Maytags reputation is not as good as it used to be. Model number mvwx5008wq and ser number. C41430792. If you are planning on buying a washer do not choose Maytag!

Purchased our dishwasher 11 months ago from Lowes. Dishwasher has a 10 year warranty on racks and 2 other items. We are 2 adults in the household. Dishwasher is maybe used 4 times a week. Very light use! Circulation pump is bad which also took out the dishwasher solenoid. Im not going to fix because it if only lasts a year again that is a very expensive repair. Very disappointed in this made in the USA product. That was the reason I purchased it. Made in the USA. Come on Maytag. You can do better than this!

Maytag Dishwasher MDB8959AWS6, S#F15006566 purchased 12/28/2011. Here is a record of the product repairs done by All Tech Appliance Service in Portland. 1/12/2014 - Thermal Fuse and Control Board. 10/15/2015 - Thermal Fuse. 9/2/2015 - Thermal Fuse. 12/5/2015 - Unit stopped working again, strong electrical smell, probably Thermal Fuse again. This dishwasher product has a design defect. It should be recalled.

Hate my Maytag Centennial Commercial Technology washer. It takes well over an hour per load. Clothes come out very wrinkled, and my knits get holes very quickly. I would not recommend this machine to anyone. In fact, I warn people against it as I have been frustrated every single time Ive used it. Model # W10420382A.

Bought this Maytag Bravos Washer online from Lowe’s in the holiday season of December 2017 because my previous Maytag HE washer broke after 17 years. I have had nothing but issues with this washer right from the start. The clothes do not come clean as I find myself putting them through the wash cycle two or three times to have them washed and come somewhat clean. The clothes come out soaking wet that I have to put them through the rinse and spin cycle at least one or two more times. I called Lowe’s to complain about this washer and they said they only have a 30 day return policy and they would be happy to call for service for me. I told them it didn’t work from the start but they didn’t care. So now, sadly, I have a repairman coming this week to fix my new washer, And hopefully he can fix it that I can use it and it can properly wash clothes. I wish I would have her read the reviews on Consumer Affairs about this washer before purchasing this Maytag. Not happy with Maytag. I would have never bought it and bought a different brand. Codes appear on the face of the washer better. Nowhere in the manual that I had to personally download myself because it didn’t come with one. And oh did I mention that I need a step ladder to reach into the bottom of the tub? This washer should come yellow because it is definitely a lemon!

It leaves white stuff all over everything. You have to rewash or rinse black clothes at least twice. We have to clean the washer frequently or the clothes smell like mildew. I chose Maytag because I thought they were the best. Apparently, I was wrong and it was a mistake buying this.

I mistakenly purchased the Bravo XL top load washer. I only wish I could give it a zero rating. I have only tried to wash 3 loads of clothes. It is almost beyond belief that anyone could possibly think this could clean anything. My husband actually watched it “work”, and insists I call Maytag because they must have forgot a part! It does nothing but crumple/wad the middle items together and rub them...and only them...together. There is no movement of the outer items until it spins. Maybe Maytag should enlist people who actually do laundry to “test” the items they put their brand on. I know the government and the energy rules have added to the complex problem of buying something as simple as a washing machine...but this piece of junk is almost laughable to watch as it destroys your laundry. I’m almost embarrassed to let anyone know I bought it. Thankfully, I have 30 days in which to return it.

Pleased with all the features. I have had zero problems with this Maytag refrigerator; no problems with the ice maker; the crisper works well. The adjustable shelves are so convenient.

These machines have lots of service problems, although Im not familiar with the newer models. The function and the features are adequate, and typical. And overall, again, I have no complaints other than shortly after purchasing, there was a circuit board recall for these machines, and fortunately, I had a repairman who knew of the issue, and guided me to a cost free fix. Overall, it has served the purpose well of cleaning my clothes in a decent fashion.

In the process of self cleaning mode, oven died with door locked. Thermostat and thermal fuse went out, couldnt get oven door open or control the situation in any way except pray for no fire and wait for hours till oven cooled down. Door could not be opened, it died in lock mode. Called repairman, already in to 2 repair bills, still not operating. Called Whirlpool and Maytag, no help!! But amazingly they have created a new kit for the blower unit in this oven, model # Mew7527AW00. I paid a bunch of money for this oven, which replaced a 40 yr. old oven that had been in its place, operating fine, but it was Aqua Blue!! Its so sad that a huge Company as this will not help with an almost new Oven??

My fiance bought this dishwasher 5 years ago but has never been able to use it due to the fact he is disabled and unable to open the door. When I moved in 4 months ago, I began using it regularly 2-3 times a week. Yesterday, I loaded it and when I hit the start button, it did nothing. The lights come on but the start button doesnt seem to be working. I have torn it apart twice and after looking all over the internet have determined that the control panel is bad. We live on a very fixed income and fixing something like this will take a large part of our budget. I am shocked that something so expensive can only last a few months then stop with no warning. We will be calling and adding our names to the list for the class action lawsuit here in California.