The Maytag Bravos washing machine may well be the worst appliance available for purchase. Sure it is a high efficiency machine that saves on water -- the clothes are often still dry when the complete cycle is finished. Many times there is still soap residue on the clothes. Forget cleaning anything with any amount of dirt on it because it seems as though items are even more filthy after washing them. I have tried everything the company advised and still my clothes are not clean. My advice... please do not purchase this machine. You would be better off taking your clothes to a river and beating them on a rock. #wearingdirtyclothesforever

I have the Maytag Bravos washer and dryer. The machine has broken several times every year, and every year, Maytag makes me feel like it is my fault. They built a machine, and they do not stand behind it. And I cannot get a local machinist to work on it. I have asked Maytag to replace it from the start, and they refused, telling me its out of warranty. The only thing out of warranty is the frame--all parts are new. Here is the history:On 1/04/2008, I purchased it from Home Depot, and it cost $815. Then in 4/2009, there was an F51 code, and Maytag replaced the mother board after long hold times and much pleading to help me. They said they could do nothing, because it was out of warranty. It took manager to manager to manager to get the agreement to extend the warranty. (I then found that this was a regular Maytag issue.)From 9/2010 to 10/2010, an ld code occurred. The approved Maytag scheduled service had to come out 4 different times to attempt to fix the issue. One time, they said it was broken wires for the drain pump. The next, it was off balance; and the next, it was a sensor. Then the next time, they replaced the mother board again, and again after much argument that the part was less than a year old. Each time, they get more and more difficult to deal with and made me feel more and more like I am asking them for something unreasonable. The service guys said the washer was like new.... All new parts and I would never have a problem again. It cost $80 after argument, and Maytag covered the parts.Last 2/2011, problems include a fast spin, ld code, and off balance; and it stopped working. It needed new suspension rods which cost $250. Maytag paid nothing. Then in 8/2011, ld code started again, and I would have to turn off to drain and then restart to spin. Maytag called in a service call, and they never showed up. Every time, they said they read over my file and that theres nothing they can do to help me. And no one else for me to speak to.In 10/2011, the ld code came on permanently. The Maytag call I made this time again said there was nothing they could do to help me.I am so frustrated; I dont know what to do next. I threw away an older set working washer and dryer, thinking I made a great decision to upgrade to this new set. Now my family of 5 cannot wash our clothes. No one will work on the washers locally, and Maytag treats me like Im complaining for nothing and I should just spend endless dollars to fix this machine. And Im at a loss. I had to get a part for the dryer the other day, and the parts store person told me that this washer is one of Maytags mistakes. if that is so, why wont they help me?

I need a new circuit board for a $2500 refrigerator. It was Saturday night of a holiday weekend when the ice chute started opening and closing and lights on door panel flashed like crazy. I called Maytag, who set up a service appointment for me for Monday. The tech came at 6pm and said there was nothing he could do without a part from Maytag and left. I proceeded to throw out all spoiled food and load a cooler with ice. I called Maytag, and they said it will take about a week to receive the part and have service. I have children in the house, and we live in Miami. I said that I would pay for overnight delivery of the part, and they told me it couldnt be done. I called this morning for a tracking number of the part, and they told me that it wasnt sent out as of yet. According to the internet search, this is a problem with a considerable amount of model number MF12568AES, and I should have been notified by the company. They claim it is a special project, not a recall.

On August 25, 2011, we purchased a Maytag washing machine (Model Number MVVYC400XW2) at the Lowes Saugus, MA, store. Initially, we had no performance problems with it; however, on January 12, 2012, the washing machine wouldnt start. That day, I called Maytag for service on the machine, and it was fixed. Then on August 18, 2012, the same thing happened. A serviceman was called for the second time, and was repaired. Ironically, the Maytag 1- year warranty was expiring on August 24.Prior to the expiration of the Maytag warranty, I had been contacted by mail about an extended warranty plan, which I thought was being offered by Maytag, which it wasnt. The offer was being made by Federal Warranty Service Corporation. I purchased a 5-year extended warranty, expiring on August 25, 2017, the reason to have coverage for what seems to be a faulty machine. I would probably need it.Dealing with Federal Warranty has been nothing but grief. In 2012, the washing machine, had required 3 service calls, one with a Supervisor explaining my frustration with the number of service calls I have had made for the washing machine, but nothing has changed. Thus far in 2013, I have made two (2) additional calls for service on the same washing machine. Not only are there the numerous service calls made but the inconvenience of not having a washing machine, and the additional costs for outside laundering, during that time has to be taken into consideration. Additionally, my wife is 68 years old, and Im 71 (72 in August). Going up and down the stairs to the basement isnt something we should be doing, especially to find an inoperable washing machine.

I was all too excited to FINALLY own a new set! I conducted research and read reviews. We decided on the Maytag Bravo XL set (Lowes) and was thrilled! For the first 6 months. They were both fantastic! 6 months later, several times the clothes washed were soaking wet as if they had been set on soak. It continuously alerted to clean after 3 loads. The dryer... Well, evidently, if you live in a high-humidity region, DO NOT HOOK TO THE WATER LINE FOR THE STEAM OPTION. It will soak your dry clothes! After 3 loads of drying, it fails to re-start for the 4th load for at least 12 hours! When paying over $1,590 for a new set, this should not be an issue. Mind you, I do laundry once a week - 5 to 7 loads including linen. Fortunately, we paid an additional $200 for the warranty at Lowes.Lets see what happens there!

Bought the xl about 14 months ago. NO LIE! Exactly 2 days after the 1-year warranty was up, the xl went down. Drive shaft and bearings. Did Maytag honor the warranty since it was only 48 hours past the expiration? Not just a no but a why are you bothering attitude. My brother and I are above average machine builders. Well fix it ourselves because we could buy a new one to have it repaired. After many hours scouring the web we found the parts. Maytag didnt make a repair kit available to the public. 7 hours plus over $200 to tear it down and to clean the muck trapped at the drain. Then sand-smooth the burnt on metal where the bearings sit. All for a washing machine that sucks at washing clothes in the first place. Never ever again will I buy a Maytag.

The Maytag Commercial Technology wash machine, the one with the clear top, leaves soap residue on our clothes. We have tried different detergents, always high efficiency, using the extra rinse, using the deep fill and nothing works. We have tried cleaning with vinegar and using the clean washer cycle. We had 2 technicians look at it, one tore the machine apart, both said nothing is wrong with the machine. So, we are left to believe that we are stuck with a machine the leaves soap residue on our clothes as Maytag will do nothing for us because of the assessments of the technicians.

After less than 3 years the interior lip of the machine is rusting. I found this when I was cleaning the interior of the machine because my white clothes were coming out with black soot on them. I can estimate that bleach was used in the dispenser 3-4 times tops over these 3 years. Very disappointed in the equipment. Ive submitted a complaint to Maytag with hopes of a favorable response. This should not be a warranty item...its defective design.

Not yet two years old, my Maytag Bravos dryer stopped working. When I called a technician to see what the problem was, he told me that the circuit board was burned out and it would be $500.00 to replace. I then called Maytag to find out if there was a problem with this machine and was told no. This apparently is a lie as there were numerous complaints when I checked the internet. I have five Maytag appliances and at this point, only one has not caused a problem. Maytag is not the company of the past when if you had a Maytag, you had the best. The repairman no longer sits around with nothing to do.

A week after warranty expired, our 1 year old Maytag gas range (model# MGR7662WS 4) required new Direct Spark Ignitor (DSI) board. Knowing it was just beyond warranty, I inspected wiring first and found that the Bake connector on the DSI was loose, flopping around from a bad solder point on the board. Called Maytag and informed them of this manufacturers defect and all they offered was a $20 discount on a replacement part ($220 instead of $240). It worked with new part for 4 days, then something else went bad causing oven to spark, light, heat to less than 100 degrees, then shut down, then restart, then shut down, then restart, then stop doing anything. It has never worked correctly since then. How can a manufacturer of almost all domestic brands get away with such shoddy workmanship.. Taking advantage of defective or poor quality parts to sell more of the same when they fail and for an enormous markup? Where are the regulators who oversee monopolies and blatant scamming of American consumers?

Used my washer ONE time and when the load was done my clothes were soaking wet. Tried to get the clothes to spin dry but the washer would not work. Called for repair. They replaced the activator. I did one load of laundry. It worked fine. Did a second load of laundry and the clothes were soaking wet. The washer would not do anything else.

Hello, I bought the above top load Maytag washer last summer and shortly after purchase the spin cycle was accompanied by a load grinding noise. This became progressively worse per use and I contacted Maytag Canada. The experience calling is a challenge with often busy, and at times long waits. When I did get through on the line they were very good customer-service-wise and arranged for a local accredited company to attend my home and assess the problem. Service visit number one resulted in the lack of parts to fix, so I waited two weeks for the next visit with appropriate parts. Washer began to grind again, I called Maytag, another appointment was set, service call #2 again resulted in the SAME parts being replaced as service #1, and upon departure the washer immediately resumed grinding. Call #3 to Maytag and a 4th visit was scheduled to my home. This time with a different service provider, parts changed washer not fixed. Maytag called and this time I asked for replacement. Three weeks later I received a new washer. The version was updated so the drain hose no longer reached my drain pipe. Once sorted out, my first wash today with the new unit and GGGRRRIIINNDDDING.. I would not recommend this product. Will be calling Maytag again Monday.

This machine may save water but I spend more time and money getting out the severe wrinkles it creates. I use my dryer and iron much more than with my previous washer. I never thought a new washer would make wash day more difficult.

We like the refrigerator and we have had it several years. But the thing the top freezer conceals much of the top rack of refrigerator. We must duck and almost kneel to get to food inside. Next fridge will have drawers and doors that open on both sides.

My washer is about one-year-old. Several months ago I noticed a brand new shirt was damaged after laundering. I thought it was inferior material. A couple of months later I saw a similar situation with another garment and started being more careful with the laundry settings using delicate, short, light washes, etc. The problem has happened a THIRD time to another garment. It appears this washer has a hunger for delicate jersey type fabrics. I started reading online and found out at it is indeed the action of the agitator and I need help rectifying the situation.

I own a Maytag dishwasher - it is a few years old now. I first filed a complaint in 2011. We have had it repaired several times - the control panel keeps breaking. Why is it that my grandmothers old dishwasher worked for 30-40 years and now you are lucky if you can get an appliance that works for a year without breaking? This planned obsolescence is ridiculous. Do not buy Maytag products - hit them where it hurts - in the wallet. They used to build quality products, but not anymore. I contacted the law firm in California that another person had listed as they have started a class action lawsuit. Eppsteiner & Fiorica Attorneys, LLP, at 866-548-8857 - if you are having atrocious problems with your Maytag dishwasher (they mentioned Fridgidaire, too) - because of the control panel, please call. The company wont fix the issue unless they are forced to.

I bought a new Maytag refrigerator 5 years ago and it has been nothing but a headache. Ive spent more than $700 getting it repaired. The Maytag repairman is no longer lonely, hes really busy. These units are crap and the company does not stand behind their products.

We purchased a Maytag refrigerator and right away had a loud noise. Found out the ice maker was on even though we dont have it hooked up. Now our freezer isnt working. Food is defrosting and ruined. Bottom half of refrigerator is freezing everything. Our fruit and pop and water and lettuce all frozen. 4th time they came which is today. Now says our freon is low so well see what happens. The repairman was so rude he was yelling. We said our Popsicles turned to slush so he said, Dont buy any. He was so nasty. No more Maytag for us – waste of money. Even had the compressor replaced. Wasted 1100.00.

Like many I have never wasted my time writing a review, this time I have had it. Purchased all new appliances from Maytag, biggest mistake I have made in the last 10 years. Front loading washer is the main culprit. Doesnt clean clothes, have had to replace the rubber boot on the inside twice now, machine is only 3 years old. Maytag basically treats you like youre stupid, resend instructions like that will fix their broken P.O.S machine. I will never buy another Maytag and will be sure to let everyone know what a piece of garbage, from machine to company! Sad that the overall reviews on my machine are 1.3/5 stars on Maytags own website. Oddly, I cannot write any review on their site, Maytag must have realized what a POS theyve been selling and now block reviews. Im thinking that we should get enough owners together and file a class action lawsuit, maybe that would change their tune??? Never BUY MAYTAG, PLEASE keep in mind THEY are UNDER AN UMBRELLA with WHIRLPOOL and MANY OTHER MAJOR PLAYERS... Do not let them scam you the way they did me! If you work hard for your money spend it on a more reputable brand that will not try to stick it to you because they build junk!

I purchased the most expensive stackable set available. After 3 years the Maytag Front Load Washer is dead. Wont turn on or receive electricity. It stopped in the middle of a cycle so I have an entire load locked inside. A repair person came out and confirmed $600-$1,400 to replace computer electronics. Right on the front of the machine, there is a shiny tag displaying 10-year Warranty. I live chatted with Maytag. Only the drum and some other ridiculous part is covered. She told me to call the 800 number to speak with a customer rep. After trying 2 times and being put on hold for over a half hour, I hung up. I WILL NEVER BUY A MAYTAG AGAIN!

We had been a Whirlpool only brand household for as long as I can remember. When our Whirlpool washer and dryer gave out on us 11 years ago, we had a friend swear by the quality of Maytag appliances and decided to try something new. We purchased a Maytag Atlantis washer and dryer set. We have had our Maytag Atlantis washer and dryer since 2003 and both appliances are still as dependable and hard working as the day we purchased them. We live in a house with well water and our water is treated to be soft water.We have 2 daughters and 4 grandchildren who have come and put our machines through some heavy duty challenges when their non-Maytag brand washers and dryers have failed them. We are still very satisfied with our Maytag purchase some 11 years later, and so are our daughters and grandchildren!

I purchased a Maytag microwave oven on July 22, 2011. It was delivered August 2. Model no. MMV4203DW, serial no. CK01001086. I paid $279 at Lowes Spokane Valley WA. I made a family brand name dinner for six in the original black carton, put the rack into the microwave, followed all the directions as the microwave was new. The carton melted inside and burned a place where the rack had rested. This melted before the time was up. I had followed all the directions. This was the first incident that was a problem. Next incident was a large bag of popcorn (microwave has two settings for popcorn--large or small). This burned the bag black before the allowed automatic setting. Third incident was another bag of popcorn, which resulted to a fire. I tried putting it out with a large lid, which now has permanent black smoke stains. The fire was so hot I could not remove the popcorn bag. I had to use two pancake spatulas to throw it outside where it continued to have flames and burned itself out. The next fire was with a baked potato. This was set for a regular potato setting. This fire was great flames. I tried putting this out with salt and a pan lid. I also removed it with a large metal strainer, an Asian type which is large, and used another spatula to scoop the flaming potato and took it outside while it continued to burn. This time the microwave burned itself out. All lights would not function so I unplugged it from the outlet. I have repeatedly told Ava that I had previously owned a Kenmore convection microwave and the only time I used the rack was when I baked something. She continued to ignore this and said that I used the rack to make popcorn, baked potato, etc.

Maytag Bravo Quiet Series 300 - I purchased the set 2.5 years ago and after 2 years, it started making a rubbing sound. I kept using it with having a family of 5 and this is why I purchased it in the first place; with 3 boys, I do a lot of laundry. It then quit working on me all together and wouldnt spin the clothes. I had a technician come out and it was the barriens that spun the drum so I had them fix it and it cost me $400. Then about a month later, it was flashing code F51 and not spinning. I had them come back out thinking it would be covered since it just got fixed but no, it cost me another $100. Now, 6 months later and here I am again unable to do laundry because its flashing F51 and wont drain or spin. I called Maytag and they tried selling me a warranty and said it wasnt recalled because there wasnt enough complaints. We need to all call and raise a ruckus. This is ridiculous. Sorry to hear everyone going through as I am.

I just purchased this Maytag Commercial Technology Washer and Dryer on August 31st, 2018 and We hooked it up today Sept 4th 2018. I put a small load of towels in this machine and it said it would take an hour and thirty seven minutes to wash. I added my detergent and pressed all of the necessary buttons and started the load. the machine started spinning and testing and adjusting. I waited to hear the water start to come into the washer but nothing. I then checked my water lines thinking they are not on but they were. Through the smokey glass on the washing machine, I could see water dripping as if it is hooked up to a slow drip IV Machine.I am taking this thing back ASAP!!! First thing in the morning on Sept 5th 2018 I do not need to call Maytag Customer Service because they know it is a piece of junk, so I do not need to waste a moment with this crap on my property. I see Maytag does not believe in a QUALITY ASSURANCE DEPARTMENT because that department would put a stamp of approval on this Junk for distribution.No Washing machine should take more than 30 minutes (40 mins max) to wash no clothes. I will have to invest in an old school scrub board and rocks, then I can understand an hour and thirty minutes worth of wash time. I have set the timer on my phone when I started this load and My towels have been in the washer for an hour so far and I can still hear the slow IV DRIP OF WATER going. I just checked the machine and the digital reading is saying it has an hour and thirty three minutes to go. there is no water in the tub of this washing machine. The towels are wet from the IV drip and the machine is now pretending to agitate the dirty towels but it is only going in one direction. It is truly a sad state of affairs, your hard earned money gets you nothing but junk and a runaround.

My husband and I purchased our Bravo washer and dryer from Home Depot about 5 years ago. They have been the worst ever. Clothes always tear and we continue to receive an F1 error every time we try to wash something. I dont have the money to buy a new one, but I sure wish I did. I will never buy a Maytag anything ever!

I thought washers are supposed to last 10 years or something. 3 years and I have to replace it. I dont know who Im more dissatisfied with - Maytag or Direct Appliance where I purchased it. Just thought I would rant and warn others about this brand. The computer died so it doesnt know what cycle its on. Repair guy said its unfixable. ARGH!

This washing machine is TERRIBLE! If I could give it zero stars I would. It broke right after the first year and has been nothing but trouble since. Agitators has been replaced twice. Clothes do not get clean. Do not buy this machine. When I contacted Maytag with my initial complaints they were not helpful. Please save yourself the trouble and buy a different brand machine.

We bought 10 18-lb washers about a year ago. They are a maintenance nightmare. For example on June 5 7 out of 10 machine were out of service. One has been down since Jan 20 and the others for various lengths of time. The guarantee for these machines has been misleading since the parts for repair are never available. We are losing business and money because of the Maytag failure to provide equipment that operates as advertised. We need help now.

I had the microwave serviced and they heated a cup of water which was fine. I heat food on the tray and only one side gets heated. I have to turn the plate to heat the rest of the food. I never had that problem with a turntable microwave. I cannot understand why they are still selling this inferior product. Maytag used to have excellent products. What happened to this company?

Dryers been installed for 3 months, 3 service calls to date. Heat unit failure. 1st service call no show, no call. 2nd service call fixed the problem 50%, the dryer would heat on timed dry but no other modes. A week after that call heat unit failed again on all modes. Awaiting 3rd service call. Customer Service Department at Whirlpool Canada could care less. Avoid this product, Maytag 2000 series dryer - do not buy.

Lets be real and say that people with good experiences dont often end up on websites writing reviews because they are busy enjoying their product! I purchased my set in early 2012 and will admit that initially there was a learning curve with using a washer with no agitator. I enjoy doing laundry and Im really good at it but with this washer I had to change my routine. Always pretreat stains. Deposit clothes loosely around the drum and shake clothes loose before putting them in the dryer. My clothes come out great! I have a child, two dogs and a greasy truck driver man and everyones clothes smell great. I can wash my king bedspread and anything else in my house with no issues. And my washer has never torn any of my clothing, however fragile. I dont iron often and I hand wash nothing.I give 4 stars instead of five for the extra steps to ensure my clothes are clean and wrinkle free. No they dont make things like they used to but thats with all the new stuff. My moms 3000 dollar Samsung set (her washer) isnt working as I write this. Too bad more people with good experiences dont get online and share. Hope this has been helpful.

Oven racks falling down and theres appears to be no solution because the interior liner of the oven has warped. The 3rd party repair guys tell me the interior liner needs to be replaced, its not worth the repair cost, Im better off shopping for a new set. Its so unfortunately that this happened (we moved into this house with existing appliances that we cannot use...) and it seems to be a common problem, yet Maytag claims they have NOT received any complaints about this.

I have never been so disappointed in purchasing an appliance for my home. The Maytag Bravo XL large capacity top loader, has never worked properly, and I have many ruined pieces of clothing. Although it has a very large capacity, the water barely fills to a 1/4, and clothes are sticking out of the water, while they are supposed to be submerged/being washed IN the water. Clothes come out of the washer smelling foul. WORST WASHING MACHINE EVER.

I purchased a Maytag electric dryer Bravo 300 Series in November 2009. December 2011, the main computer board went out and had to be replaced. Do not purchase Maytag appliances. They do not stand by their defective products. First and last Maytag purchase.

I purchased a Maytag quiet series dishwasher (Model Number: MDB6759AWW) for $500.00 in May 2009. Three months later, I started experiencing difficulty with the control panel. One light would continue to blink and it would not do anything else. I called to have it repaired but by the time he was to come out, it started working again only to stop working again the next week. On 7 Oct 09, the repairman came out and replaced the panel. Then, about six months later, it stopped working again. I called again but canceled the appointment because it started working again. Then, after having it for one year, it stopped working again and I called only to be told that it was no longer under warranty. Now, we cant get the control panel to do anything. From all the other similar complaints I have read, it seems like there is a defect with the control panel. A dishwasher should last for more than one to two years. This is very frustrating.

We had a wonderful Bisque Maytag double oven in 2002. We bought new stainless appliances this year, and have been very disappointed with the range. Why do you have to hold the temp and timer settings one increment at a time to set it, and why do you have to push Start after that? Frequently we set the temp or timer and walk away, only to find that the oven or timer did not begin because we forgot the new step. When the timer goes off, you have to push it twice to get it to reset. The burners themselves have too many confusing pictures for the settings. What happened to low heat, medium and high and hash marks in between? The stove top itself is a nightmare to keep clean. Give me back my coil stove any day!!!

I have the same complaint as everyone else. I have had my dishwasher since April 2013. Less than 9 months after having it the control panel went out and they came and replaced it. Now June 2015, 2 years and 2 months after purchasing and a year and a half after the control panel was replaced, none of the buttons work except the cancel button. How is it that these machines, as expensive as they are, crap out after 2 years! Such a waste on money!! Maytag has lost my business forever!!

I purchased this high-end dishwasher 7 years ago and 3 years of fairly light use, the control panel on the top would operate sporadically or not at all. Called the dealer who sent out the repairman that installed it and had to replace the control panel to the tune of $300 once the labor was included (took 2 visits as he had to order the part, so 2 trip charges). Now 3 & 1/2 years later, it is doing it again!! A call to Maytag and then a transfer to Whirlpool customer service got me nowhere. They said there were no recalls or documentation for problems with the dishwasher. Really??? I see lots of complaints on this problem with very similar Maytag dishwasher models. They would not send me a new part at no charge as a result but offered to set up a service appointment for me so I can spend another $300 (probably higher now after 3 years) and would register my complaint. Thanks for nothing!Doing that would turn my originally $900 dishwasher into a $1500 one with the result that it will probably fail again in 3 years. Absolutely ridiculous customer service. I saw a YouTube video on taking it apart and applying silicone around the ribbon connections as others have done in the hopes I can get it working again for a while as I dont have the $$$ needed to replace it again on a retired fixed income. :(

I am happy with this dishwasher. I had a GE that had a lot of problems. I insisted on getting Maytag and I have been happy ever since. It controls the time, temperature, and is easy to operate. I would like a bigger dishwasher because of my family size. This dish is okay for a family of 4. It matches my furniture. It blends in. No complaints. The digital pad is convenient but it has been fixed a few times. I had a few technicians who did not know how to fix. It was not the dishwasher, it was the technicians.

My fairly new Maytag dishwasher took a break and stopped working. No lights on the control panel although there was power to the appliance. First repair call, I needed a new computer board. Then when the part arrived and was replaced, no lights on the control panel! Fuse checked out ok and now waiting for a control panel replacement. Really??? Dependable Maytag? No way and never again to purchase from this company (Whirlpool).

Overall I am satisfied with my Maytag Model MDB8859AWW2. I purchased the dishwasher 06/05/201. However, the door spring squeaks. It is a grating sound.

We purchased a $500.00 Maytag dishwasher, Model #MDB7749SBW, in August 2013. In December 2014, a little over a year of owning it, the pump failed. We called Maytag and they had a service company come out and replace it. We paid $181.00 for this service call. In July 2015, the control panel failed so we called Maytag to see if they would replace it at their cost. All they are willing to do is to send another service guy out at our expense. The service call is $89.95 and that doesnt include the labor! The total with tax will be close to $200.00 again!!! Now we are getting close to spending $1,000 for this piece of junk! In addition, this dishwasher is only used three times a week because there are only two people living in our household. It is obvious after reading the other complaints that the control panels are defective and I am sure that Maytag is well aware of this issue. So, buyer beware. Dont even consider purchasing a Maytag dishwasher unless you enjoy watching your money flush down the toilet. They dont even deserve a 1 star rating!!!

I have a Maytag Centennial washing machine which is about 3 years old. In the past 6 months I have to replace the actuator twice. I have had Maytag washers for about 40 years. I will never purchase another one unless it is the old style. That would mean that it would be a used one. This machine is a bad purchase. Maytag use to stand for quality, but not anymore.

My Bravo washer does NOT clean my clothes. I have tried many detergents. I have to pre-treat all spots with dish soap and run hot water over and then rub the spots out. This was the only recommendation given after consulting with Maytag. I have to pre-soak my clothes in a pail of water with detergent. The water is brown. My clothes are dingy, spotted and have bleach spots. I am very careful so this is not from pouring into the bleach dispenser. Maytag was the reason I purchased this washer. Never again.

I am grateful I dont have to beat my clothes on a rock. Absolutely the worst dryer Ive ever had!!! Previous Kenmore washer was my favorite! This Maytag does not allow me options to stop, soak & freely open & close as I choose. Even my adult children who occasionally use it say its the worst!

Washer Bravo MVWX655DW0 - Maytag has shipped the wrong part twice, sent me the right part which is faulty and the 4th one arrived today. I have not had a washer since 9-16 October 9, 2017. I am writing to tell you about my experience that Ive had with Maytag over the last 30 days. I have owned several Maytag and Amana appliances in the past; along with owning several currently. Over the years, weve had a wonderful experience owning these appliances however the last 30 days is one that has been unbelievable. On September 18 on a Monday early in the morning I called Maytag service line. I spoke to a young lady who had difficulties finding me in the system and did not know how to make an appointment to have a Maytag repairman come to my house to look at my washer. I did not take down her name as I thought and trusted that the company was acting on my behalf and would take care of me.I spent several minutes explaining to her that I did not live in Indiana that I lived in Iowa and that I would need a repairman who is close to my hometown. She continued to give me phone numbers with area code 407 in Indiana and then kept repeating some type of a ZIP Code 49 something for Indiana. I explained to her four different times that the zip codes in Iowa start with a five and the area code would be a 515 number in the area she was looking at. She finally gave me two phone numbers, one that did not work. I asked for a repairperson out of Jefferson. She told me Cranston Repair and gave me the phone number. She told me to call him. I told her that I would go with the Cranston repair since Jefferson with my hometown and it was close to where I lived.I then asked her if she would make the appointment. She told me she didnt know how to make the appointment and she kept messing up with the system. Not sure if it was her first day or not but that was fine so I said “never mind I will set the appointment up myself. I then asked her to double-check to see if our new Maytag refrigerator that we just purchased was registered. She told me she did not see it but all I needed to do was call back the next day with the model and serial number and anybody I spoke to on the phone could go ahead and get that registered. I thought I had registered online; I only wanted to double-check but she didnt see it so I assumed I did something wrong and then would make the call back the next day.I called Cranston repair and scheduled an appointment with the repairperson for the next day Tuesday, September 19. Repairman came the next day on time, looked at the washer and found that the transmission had gone out. I had purchased the washer just shy of two years ago. The repairman said that he would have to order the part and would let me know how long it would take and would return to fix the washing machine. He called from my house and was told that the part was on backorder until October 5. After the repairman left the house I decided to call Maytag back and express my disappointment in the product as Maytag says they stand behind their products and the fact that it was not even two years old and that a transmission would go out. The individual I spoke to this time, Antcwaniqua? Not sure about spelling, listened to my story. She also told me the part the repairman ordered was not correct.I needed part W1 1132267. She said that was a substitute part for the correct part that I needed which was W11035204. I told her that the part number ending in 204 we were told was on backorder until October 5. She said no, the part may show that in the system for repairmen but Maytag can locate the part in a warehouse, it would be shipped in 3 to 5 days. I told her that he had called a place in Davenport, Iowa. What she would do because of all the issues I was having was she would go ahead and ship the part out to me at no cost in 3 to 5 days.I wasnt sure about that warehouse thing. It didnt sound convincing but at that point I had to go along with it. What was shipped out to me was the substitute part W1 113-2267. At this point she told me that I would have to pay to have the part put in; I agreed to that on I want a new washer or I want my washer repaired within 72 hours at no cost. I have not had a washer for 3 weeks plus. Repairman in coming Friday and I am not confident that the 4th gearcase part that came today will work either.

My Maytag washer and dryer (5000 Series) is about 2 years old. Just as soon as the warranty ran out, I started getting F35 and suds error messages. Information found on the internet tells me that many Maytag customers have experienced the same problem. Whats up with this Maytag? Since many of your customers have experienced the same problems, are you willing to meet the consumer in the middle by repairing the product at no cost or are you building the appliances to last as long as the warranty?

This machine sucks. Im down to washing three to four items only on an extra capacity machine because every single load becomes unbalanced. Feeling the weight of each item and then placing it correctly doesnt work. Repairman came out. Said it was balanced. Lie. At this point I want to take a sledgehammer to it and send the pieces one by one to Maytag. They should be embarrassed to even have this product for sale to the public with their name on it.

I purchased the top load Maytag Commercial Residential washer with an agitator last month. I wanted a basic washer with Hot/Warm/Cold settings, Delicate/Normal/Heavy Duty cycles, Small/Medium/Large loads. I paid over $800 for this washer and I cannot wash my whites or rags in hot water! The hot water setting dispenses hot water, then cold water, back and forth. The end result is cool water. Ive called Maytag, Ive been told that there is nothing that can be done about it, thats how theyre made to be considered HE. I asked them why they even put a hot or warm water setting on the washer.You have no control over the water level, all cycles except for normal run in a deep water setting (full drum of water), I dont know why delicates are in a deep water setting. I only wash a couple pieces of delicates together. I end up using a lot more water and detergent with this washer. I hope we dont have to conserve water in the next few years! So though this washer uses less hot water energy, it wastes a lot of water, my water bill goes up and my detergent is used up much quicker! I cannot add time to my wash cycle, (the actual washing/agitation cycle is very short - 10 minutes) it has to drain all of the water and re-start the cycle with more water! $800 is a lot of money for a washer that doesnt wash like my old cheap washer. The local store cant do anything about it and Maytag brushed me off.

This will be the third repair of this refrigerator in one year, the same issue of the refrigerator warming up. Water all over the floor due to ice thaw. Also food spoilage. I want another refrigerator at this point. The Maytag repairman is definitely not lonely. He has more business than he can handle with this defective refrigerator. Terrible. Do Not Buy!!

13 months after purchasing MDB7749SBM3 dishwasher this lights started making no sense. For me the buttons still work, but it seems like only a matter of time until they stop working too. Like many others, I opened up the door and found the corroded ribbon connector (see photo). It wasnt damp so since the corrosion happened at the point where a ridge of plastic presses the ribbon against the hot handle, I suspect heat. Obviously a design flaw. Come on Maytag. Recall?

We purchased a Maytag refrigerator Model # M1TXEMMWS02 and Serial # E01103420 in April of 2010 from Home Depot in Aurora, Illinois. First off, we did register the fridge online via Maytag which of course, they have no record of! Now, we go on vacation and come back to all of our food ruined because the refrigerator stopped working! No refrigerator should stop working within two years! I called Maytag and they offered me a Repair Plus One package of $302.73! Are you kidding? We paid $400.00 for fridge. Then of course, only one-year warranty and have to pay at least $75 for a service call, labor plus parts! If it’s the compressor, the charge is $326.20, plus shipping and handling! What a joke! There needs to be longer warranty and should offer free service calls and much more. I am disgusted in Maytag products and in which we purchased due to a reputable name! Never again.

Yesterday, the main compartment of the refrigerator is not cooling. The freezer still is working. This unit is 2.5 years old! I have never bought an extended warranty before, but on day one, this unit hardly ever shut off. It didnt seem like the electric bill was any higher but never felt good about the unit. Plus, I hated the ice cubes all over the floor when I pulled out the lower drawer. The monitoring device is in the roof of the fridge and takes up a lot of square footage. Nope, will never buy another Maytag. If their products cant last more the at least eight years, then it is such a waste of our money. Do better! Im writing Consumer Report and the President of the company. Who replaces all the food loss?

I purchased both a Maytag washer and dryer and I am very disappointed in both products. Both appliances have electronic controls and are substandard. For the dryer if you do not touch the start area exactly right it will not start, can take multiple tries. For the washer, my town turned off my water to switch out the meter, once done the washer did not know how to clear the air in the lines and gave a LF error and no one at Maytag customer service could help me solve the issue and then could not set up a service call as their computers were down and did not have a process to call back the customer. This is terrible Customer Service - never again Maytag or any of their other products????

I purchased a Maytag Bravos Quiet Series washer and dryer in 2009. The repair people have been to my house 7 times. The dryer had a useless part on the drum that made a banging noise while running. The washer keeps getting coins and small undergarments stuck in the motor. Every now and then, one of us leaves a coin in the pocket by mistake. I did purchase the extended warranty on the set. The repairperson that comes to my house is great. I would, however, not want to have to keep leaving work to meet repairmen. The machines are not quiet. If you need quiet from your appliances, this is not the set for you. If you do not clean the washer with Affresh or Clorox product, your clothes and your room smells. The clothes are always so tangled after washing; they tend to wear out quickly. Im not sure about this high efficiency washer. I wish I had just purchased a regular machine.

I purchased this dryer in September 2011. By August 2012, one month before the warranty expires, the thermo fuse blew and the dryer would not dry; no heat. I replaced fuse and 30 days later, it blew again. I replaced it again and now, March 2013, 6 months later, the same thing; the thermo fuse blew, no heat. The vent is clean and air flow is very good. Maytag will not admit a problem. This is not an inexpensive dryer; it may be cheap, but not inexpensive. Maytag quality appears to have vanished. I have Maytag throughout the house but will think twice before purchasing Maytag again. Chinese produced parts/products are inferior. Maybe Ill look at Bosch or LG from now on.

We lost our home in a tornado in 2005 and had to buy all new appliances. So, I bought a Maytag Neptune front load washer and dryer. It was my 1st ever. I will never buy another Maytag appliance again. Just at the end of the 5th year going into the 6th year, the bearings started to go. So, I checked with the place where we bought it and was told how expensive it would be to fix. It was anywhere between $500.00 and $700.00. Well, thats crazy. I therefore e-mailed Maytag numerous times and was thanked for my complaint. But they offered no help with this matter. If they dont back their stuff at all, why would I want to buy their stuff? They could have at least offered to help with it. There are only 2 people living in this house and there is no excuse why that washer should start failing already. If I thought it was worth it, I would load it up and drop it off at a Maytag store and leave it there. It still runs. But it makes an awful noise and we are just waiting for it to crap out. I am going to try to sell it for as much as I can get out of it, hopefully before it completely stops. Maybe some fix-it guy would want it. Well tell him whats wrong and they can fix it and sell it to some other poor person. I lost my job in January. Therefore, I cant afford that much to fix it. So, I will now have to try to find something used, because Maytag does not back their stuff. I would rate this machine lower if I could, but that wasnt an option.

I have a Maytag washer that I bought new in 1995! It is still washing my clothes like a champ. It must be true - the Maytag repairman is a lonely soul, in all these years I have never had to call him!

Purchased a Maytag front loader and matching dryer in Sears and have had nothing but problems with both since the beginning. Now that the warranty has run out we have even more problems and doing laundry has become stressful. Big lemons. Wish I had kept my Kenmore units. Now looking into reviews for other brands, may go back to the Kenmore brand too. NOTHING can be as bad as Maytag.

We purchased a new Maytag Bravos X washer and dryer from Lowes in June of 2013. After a year and a half of normal use (2 people in the household) the washer needs a new gearbox bearing at a repair cost of $529.00. I called Maytag and spoke to a customer service representative who informed me that there was nothing they could do about it because it was past the one year warranty. I asked to speak with a supervisor who told me they would offer me a 50% discount on the bearing but would not pay for the repair work (the cost of the bearing is approximately $25).Needless to say I will not be having the washer repaired. We will be purchasing a new washer and it WILL NOT be a Maytag, Whirlpool or any other brand made by that company. Its just appalling to think a company like Maytag can scam customers the way they do by producing appliances that are of such poor quality and then offer third rate customer service on top of it. Maytags answer to the whole issue is selling everyone an extended warranty which we all know is as bogus as the companys integrity!!!

I am a Baby Boomer... just like so many of us, I watched those lonely Maytag Repairman television commercials. Yes, silly me I purchased our top loading Maytag Bravos XL because of the brand name and because the machine was large enough to wash our bedding. Well, like so many fellow purchasers have found, this machine does not get the clothes clean and leaves soap spots all over the clothes. Its embarrassing. Additionally, there is that funny smell after the clothes come out of the wash. Well, Maytag has really done a number on us all. Kudos to their research & development department for creating a washing machine where the clothes come out dirtier. Has Maytag thought about a RECALL? I will tell everyone I know to NEVER buy a Maytag.

This is beyond one of the most disappointing purchases I have ever made! It has been about 15 months since purchasing this dishwasher, and as of today it is not working! Blinking start button. I see from the hundreds of disappointed customer comments that I am not alone. With this many people complaining of the same issue, that Maytag should have a recall... I paid about $550. I get that quality does not supersede the almighty dollar, but come on!

I bought this machine about a year ago. It does not wash your clothes good. Stains nor smell does not come out. It makes this god awful noise that can be heard throughout the house... It suppose to save on your water and electric bill but no savings for me considering I have to wash items 2 or 3 times... I hate this washer and I paid a lot of money for nothing coz that’s what it does - nothing!!!

Bought a new Maxima washer in January. Worked for one week. Got error codes and electronics board shut down. Contract serviceman says board should have reset after turning off. Ordered new board and it is missing one of the electrical wire connector plugins. Maytag/Whirlpool is having a problem with these boards.Three weeks without a washer. Two days off work. When it goes out again, days off work will be close to what I paid for it. Thinking I may cut my future losses and buy another brand when in-transit board goes out.

I purchased a Maytag refrigerator, stove, dishwasher and microwave in 2006. Like another commenter, I also insisted on all Maytag appliances. What a huge disappointment. About four months into owning the microwave, a computer module had to be replaced. The microwave stopped working about six weeks out of warranty. It just stopped working, period. I was told by Maytag that they consider microwave a disposable product and they would not cover the repairs. It was cheaper to buy a new one than repair the old one so I replaced it with another brand. The dishwasher failed after 4.5 years (would not drain) and again it was cheaper to replace it than fix it. The oven range handle broke off (normal use) in August 2011 and that cost me approximately $200 for the part and the service call. The refrigerator has had two service calls for the ice maker to replace the motor. The first was covered by Maytag, the second by me. This occurred when the unit was approximately three years old. In August 2011, I had another $90 repair because the ice maker drain (?) was plugged and had to be cleared fixed. I have never been able to pay what I paid for these appliances. Prior to this, we always purchased a middle-range appliance and we never had problems like this.I will never purchase another Maytag product again. This is so disappointing. I live in MI and I wanted to support a MI business. Unfortunately, I wont be able to help out this particular company any longer. Dont buy Maytag appliances. It is a waste of money.

Like so many other people reviewing Maytag refrigerators with bottom freezers, I am dealing with water on the floor. At 64+, I am not eager to tackle the problem as a DIY project. Once of defrosting and cleaning up was enough. I love the looks of my 2 yr old $2000 4 door fridge/freezer but hate the issues. I guess Maytag is going to ignore all of us. When someone finds a reliable company, sing it from the rooftops.

MTB2656DEB - Well my fridge is now about 12 years old and from the beginning it was horrible ice as always forming under freezer door. The cold cut draw broke 3 times with its cheap junkie plastic. I hated it from the beginning. I have owned a GE double door with ice maker for 26 years. Wish I had kept it.

Model MDB7749AWM2. Paid over $700.00. Figure I would get a good dishwasher so it would last and clean dishes. I was wrong. I replaced all new appliances for kitchen in house we had purchase 3 years ago. I replaced door switch 4 times, front door panel where screws go in broke off. Salesman at Lowe’s said Maytag was a good dishwasher. It is a stainless front and stainless inside. I have had cheaper models and never had problems with.

Have read others reviews and experiences and wish I had visited here first. Our first Maytag washer and dryer set lasted over 25 years with only minor repairs until the transmission started to leak grease and was uneconomical to repair. Our second set only lasted nearly 10 years and were obviously lesser quality. The wife decided that she wanted the best and high tech version. She really liked the features of the Bravos 300. What a mistake! Not even three years old and she has been dealing with the noise and the problem with constant unbalanced loads, intermittent error codes, odors and the forever cleaning requirement. The whites were intermittently getting rust stains until I determined that the underneath side of the top cover around the bleach reservoir had rusted out big time. I replaced the top cover for over $125 plus an afternoon that I will never get back. (Out of warranty, of course). Today the wife called me to say that the washer would not complete the rinse cycle and she could not reset it. We had to pump out the water and pick the wet clothes out. A grinding sound is coming from near the bottom of the machine and sounds expensive. The service man is scheduled to be here day after tomorrow to give me the bad news. My next washer purchase will NOT be a Maytag or any other high tech piece of crap. Simple is better.......

I bought Maytag Bravo washer and dryer set in Nov 2012. Washer door lock broke shortly after 1 yr and now the gearbox has broken. DO NOT BUY MAYTAG BRAVO WASHER. The cost to fix is more than the value. Before the gearbox death the sound it made while spinning was so loud you could not hear the TV or have a conversation in the west end of the house. Visitors were stunned at the noise it made. I called Maytag warranty and explained I am having the same issues as everyone else, what are you going to do? The answer was nothing. Please read the other reviews, same issues. It never cleaned clothes anyway, bad design, bad company and bad corporate values. Model number MVWX700XLE.

I have a Maytag Precision double oven 850 series. The upper oven handle does not fit snugly and has been broken 4 times. I have had to order 4 new handles because the hardware does not seem to secure the handle to the oven door. There are no problems with the lower oven door.

I absolutely love this Maytag Bravos XL washing machine... I bought this machine before doing any research because of a sale and then after reading multitudes of reviews... positive and negative... I thought I had made a mistake. The absolutely most important thing with this machine is to load it properly and select the proper wash cycles. You must stack your clothes around the outside of the drum leaving the center open. You must use HE detergent. This is a Commercial grade washer and is meant to be loaded. The twisting and wringing of clothes is because of the high speed nature of the spin cycle (commercial). If you have never been to a public laundromat then you should try it and see what those machines do to your clothes. I too was apprehensive about the water levels at first... So I stood there for an entire cycle multiple time and on diff settings.The machine is constantly adding water as needed and each time after about 10 min... no matter the size load I put in. The clothes eventually were covered by water. Have had no issues with clothes that come out dry in spots. I suspect this is due to improper loading. Again my info on using this machine... loading techniques etc.. all came from positive reviewers stressing the importance of these key factors. This machine was not designed or intended for light or delicate use. So if you do a lot of those type loads perhaps this machine is not for you. As for the loudness and banging I have read about I have not experienced that. I have read reviews that the problem in some case ended up being metal or plastic drip pans used under the machine. Mine sits on concrete. Anyway hope this helps someone out.

My Maytag refrigerator is less than 5 years old; the compressor went out (only warrantied for 1 year, 5 years used to be the minimum). I contacted the company who now owns Maytag, I believe Whirlpool. They told me they can fix it, no matter what the problem is, for $380.00. It turns out they sold me an extended warranty, but that was never explained in the conversation. Prior to contacting them, I had Sears out to fix it; they are the ones that told me it was the compressor. 1 week after buying the extended warranty, the repair company came out to fix it and found out the refrigerator was unplugged and informed me it needed to be plugged in for 24 hours in order for him to determine what was wrong with it. I scheduled an appointment 1 week later. When they came back, they said it was the compressor, and they needed to order the parts. 1 week later, they came back, and the compressor they came with did not work. 3 weeks now, no refrigerator. They said they would put a rush on the order, haha. Now, I have to wait another 8 days for them to come out to repair. 4 weeks without a refrigerator? I think there is some type of implied warranty when you purchase large appliances; these companies are getting away with murder. Are refrigerators now disposable commodities? Cheaper to buy new ones than repair the new ones? What will happen to our landfills?

My Maytag top loading washer, 4 years old, stopped working in the middle of a wash cycle. Registered Maytag repairman did a diagnosis and finally identified the problem with the control board. The cost of the control board would have cost almost as much as the original wash machine especially since I had to pay for the current service call and labor (to diagnose the problem). After having read a number of other reviews from dissatisfied customers, I will not buy another Maytag product. I was under the impression that Maytag produced a superior appliance but was disappointed by this experience.

In 2011, we purchased this Maytag Centennial MVWC200XW1 washer. It will not complete the cycle when it goes into rinse and spin, will not empty water and once the cycle starts, it sounds like someone is inside with a hammer banging on the basket. Clothes come out with a powder residue on them and several pieces have had holes. Called Maytag and was told there was no service available in our area. I will never purchase another Maytag product. Used by two adults a couple of times a week, this machine should be trashed. I have to hand-wring our laundry as we cannot afford to replace at this point. My last washer was a GE and I had it for over 20 years, we replaced it because we moved into a new home thinking Maytag was the best out there. I checked for a recall because there are so many complaints on other sites but found none. We purchased from Home Depot and of course, they are no help.

We purchased the Maytag front loader Neptune washer and dryer set in 2006. Since then, the washer violently vibrates during the spin cycle - moving out of place and requiring me to move it manually. A certified Maytag technician came out to fix it and could not. The Maytag representative I spoke with said the circuit board is known to be defective and Maytag has not given any direction on how to fix, but that the board is irreparable at that time (in addition to the mold smell that emits from the washer despite the fixes for this). The old washers also used to have a coin receptacle so that any coins that were left in pockets went into the coin receptacle instead of into the pump area. This protected the pump assembly. But to cut costs, they took that coin receptacle out. This causes any coins or other possible things that fall out of the pocket to go into the pump area, getting lodged in there and requiring a costly replacement for the part in addition to costly labor. This washer does not do the best job in the spin cycle because it vibrates so much, leaving a lot of excess water in the clothes. I have also smelled a burning smell when doing loads that suggests there may be electrical issues that could cause a fire hazard. Then there is the dryer. The Maytag Neptune front load dryer has design issue with the electrical assembly. We smelled a burning smell and unplugged it. After taking apart the front cover, the heating coils had set on fire excess lint that had gotten into the heating assembly. In addition, the coil snapped in half, possibly causing a short in the wiring. This also caused other electrical issues that are causing more money to fix. In addition, this is the second time we have dealt with electrical issues with the dryer that have cost us over $400 to fix, including having to replace the drum because it was cracked. Lint and other items seems to get into the very important electrical areas of the dryer due to a faulty design in the lint tray, because the lint goes right through a hole into the areas where the heater coils are, which caused the burning smell in our dryer. In my opinion, both these machines could be very good machines if they were not made so cheaply and if they put good quality into the machines. They dont seem to be worth the price and the support is not there. Even more frustrating, the company does not stand behind the product, leading me to believe that they know about these problems, but dont want to fix them when they go bad. This can pose a hardship for families waiting for two weeks for parts while their dryers or washers are broken. Not to mention the enormous repair costs after the warranty has expired. Try to get them to replace something on the warranty and you have even more problems.

My dishwasher racks are disintegrating. I called to see what to do or if there was a recall. I was told that problem happens a lot, but there is no recall or other option other than to purchase new racks. I could almost buy a new dishwasher. I bought Maytag so that it would last a long time with few repairs. That has not been the case with this dishwasher. I had a medium grade Sears’s dishwasher for years before I supposedly upgraded to a better dishwasher. Maytag is obviously an overpriced name and the quality of their product is no better than any other cheap dishwasher.

I have a basic Maytag dishwasher circa 2012. Not sure of the model number. It works well, no fancy features but everything you really need is there. My only real complaint is that the heat dry cycle always seems to leave the dishes a little wet, but thats common enough for dishwashers. It cleans nicely and hasnt had any issues or breaks in 3+ years. Basic. Three wash cycles (light, normal, heavy); Extra rinse option, extra hot option, and heat dry or eco-dry (i.e. no dry). Nice big rinse aid dispenser. Its not that roomy inside. Id say the size is average. It looks nice - its white and unobtrusive. It works really well with Cascade dish pods. The bottom rack is kind of a pain if your plates are curved more than usual.

This washer is awful. We had repair guy out within year one 3 times. Changed the door gasket because it was a known problem. That did not fix problems. We have to drain and clean out hard to reach filter monthly, socks get caught in drain filter constantly. Horrible, horrible, horrible. Hate it.

Purchased standard Maytag refrigerator w/ freezer on top in 2012. Freezer has never been able to keep ice cream. Never called for repair because after reading several of these complaints, mine seemed to be a minor frustration. However, I am waiting for the other shoe to drop.

We purchased a washer and dryer, spent in the neighborhood of 1000.00 hard earned $$... extended warranty, the whole enchilada. Maytag. dependable, lonely repair man, ha.. that is just so much stuff. Well anyway it was a Centennial set. What junk. Never really worked that well to begin with. I trashed them both after exhausting all avenues to make it right. Well I got the hair to report the mess to consumer affairs and see if they are what they claim to be. This is more of a warning to all consumers.The stuff you consume today isnt worth the money you pay for it. The money isnt worth the time you spent to earn it. I am gonna try to find a old washer and rebuild it, and a dryer as well. Or just use solar. Best to keep the old stuff repaired and running. I dont know how many people I have spoken to about this problem. Our infrastructure is crumbling. A consumer based economy. Only there is not anyone to service the products we consume... pitiful. I guess my wife will be out back with a tub and washboard before it is all said and done... she will not like it, I guarantee that. I could not even begin to repair the washer. It was a computer operated board that did not work correctly from the beginning. The dude came out from the repair shop and fixed it while still under warranty. It died a slow painful death shortly after that. I disassembled it with a screwdriver and now have potatoes growing in the tub.The dryer has not met the same fate yet. It just sits there, anticipating the moment when I remove it and dissect it with a Sawzall. And I guarantee that day is coming. Do not buy anything from Maytag or its subsidiaries, think long term. We have become a bic lighter economy. I have been on the forefront of that movement. I did not realize it at the time. I do now. and for that I am sorry. I always expect something to work when I need it and if it doesnt, I try to repair it. Cannot fix this stuff now. The support we used to take for granted has been outsourced as well as the production of the product. Bob Dylan said it best in the song union sundown... Thank you and e pluribus unum.

We purchased a Maytag refrigerator (MBF2258XEW) less than 6 weeks ago, and the compressor has already failed! Its not good, but the reason I am writing is their customer service (or lack of it)! We were told that it would take 3 weeks to get the replacement part, which was only 45 days old. Home Depot, where I had bought it, has been great; and they pushed Maytag/Whirlpool to agree to replace it. But Home Depot cannot not get us a new one until the paperwork comes from Maytag. We were told by their customer service that it would take 4 working days just to process the paperwork! Thats working days, and this is a Friday! So now, theyve all left for the weekend, and I still have no refrigerator and no idea when I will get one! They said no to getting the part faster, no to speeding up the paperwork, no to me returning it and getting a refund, and no to providing me with a rental. Please consider this when making any new appliance purchase.

Clothes are never submerged in water. Clothes come out worse than when they went in. Every review and complaint mentioned is dead on! This Bravos XL is a piece of crap. Stay away from lying salesmen from HH Gregg. And stay away from Maytag. Perhaps we should all get together and file a class action lawsuit! And donate all monies, washing machines and dingy clothes to charity!

I bought a Maytag Dishwasher Model #MDB7749SBW2 in 2013. It worked great for 2 years. In 2015, the control panel malfunctioned. All the lights on the control panel would light up and the dishwasher wouldnt start. I called Maytag. They sent out a service tech. He replaced the control panel. I started having the same problems two years later, 2017. I called Maytag today, 9/11/17, to see if they had recalled this dishwasher. No, it hasnt been recalled. They offered to sell me a extended warranty for $400+, that would pay for the service call and parts or, I could find another Maytag, Whirlpool or KitchenAid dishwasher and depending on the model, I could get a 25-45% discount on a new one. I asked why they havent recalled this model, due to the problems that so many people are having. They dont know. Im writing this review to let those of you who have bought this dishwasher know, that the product is faulty.

I bought a Maytag Bravos washer and dryer two years ago. A week after the one year warranty was up, my dryer broke. That was in October. It took me until February to get it fixed, but within two months it broke again. It has taken me until now to get it fixed again and they found the same problem; the thermal fuse blew. Both times it has cost me over $100 to get fixed, but I still cant use every part of the top panel; I can only use timed dry cycle. I’m expecting the dryer to go again. The repair man had to re-glue the seal that went around the drum. The vents were all clean and were blowing fine, so we’re not sure why this keeps happening. Our family have always owned Maytags and they have always lasted for 20+ years. I am so disappointed with Maytag at this point and will never buy another again. Go back to the old days, Maytag! By the way, has anyone noticed they dont run the Maytag commercials anymore, because I have!

We purchased a Maytag dishwasher from Home Depot in January 2009. We did not begin using it until perhaps March of 2009, so just over 2 years ago. It gets ran maybe 1 to 2 times per week. I went to turn it on a day ago and the right side of the control panel, where you press the start button, does not work. When I checked Maytags website, I discovered there was a recall due to the heating element. So, I had the repair technician out and he told me that the control panel was bad and it would cost $300 for parts and labor to repair. We paid $600 for this dishwasher. Of course, we have the option of purchasing a new dishwasher and receive a rebate but that ends up being more than just ordering parts and replacing them ourselves, but something only 2 years old should not break. From reading all the other complaints on this forum, I am surprised that Maytag has not done something about the control panel and the humidity issue which seems to cause the control panel to go out. This is an expensive fix which Maytag needs to address. Come on Maytag!

I am very dissatisfied with this washer (Maytag Washer Bravos XL), it doesnt use enough water to cover the clothes. No matter which cycle you use, the clothes dont come clean. Who cares about water sensing if your laundry isnt clean. I will not buy another water sensing machine, I think the consumer should make that call on how full to fill the washer. Even on power wash the small agitator turns slowly. Not happy with this machine at all.

First of all how you wash a load of laundry with a cup full of water? I got this washer and dryer (XL Bravos) as a birthday gift from my husband. This is the worst washer Ive ever had. It takes forever to wash and the laundry is still dirty, it only has a cupful of water in it. Im so disappointed at Maytag for selling something like this. If anyone is doing a class act lawsuit please include me in.

Dishwasher MAYTAG MDB7749SBM - Have the same problem as everyone else, panel board. Initially lights randomly blinked, flashed etc, but still washed dishes. Now it has completely died. Dishwasher is 3 years old.

I bought a Maytag Bravos top loader washer and dryer less than 2 years ago. I started having problems with my dryer 3 months ago and after several service calls (and a few hundred dollars), it still does not dry our clothes. I spent over $1500 for the pair and was excited to have a top end washer and dryer. My biggest complaint is with the manufacturer, Maytag - they just dont seem to care. I did not buy the extended warranty for two reasons. First, I bought a nice unit and expect it to work properly for a reasonable amount of time (at least 4-5 years without any problems). Second, they are just a bad purchase and they cost about half of the unit and if you buy a nice unit, you shouldnt need one. I could have bought a new dryer for what I spent to try and have this one work properly. My wife and I spent $600 for our last set which lasted 7 years without a problem; they were manufactured by GE, which I now wish I would have bought another GE. My wife talked me into buying a new pair to accommodate the needs of our growing family. I wished I would have kept the GE pair that was working.I would not recommend any Maytag appliance: they really just dont care to provide any reasonable service to stand behind their products. What a shame. This reminds me of why many foreign manufacturers are beating us at what we used to do best - make products that last and work! The washer and dryer look nice and have many great features, but these dont matter much if they dont work.

You cannot go wrong with Maytag, even if there were issues they are reliable in repair, and parts are available so you arent forced to purchase new like some technology. I have been pleased with the front load washer dryer since 1998.

I had purchased a Maytag Front Load Washer Model no. MHWE300VW00 in 2009. Now the rear tub, basket, and belt are gone. I will never purchase another Maytag product and would not recommend them to anyone.

Bought this because it’s American made. It seems to be very glitchy. If you don’t use the detergent drawer it always flashes low detergent. The quick wash leaves soap on clothes. It acts up and leaves clothes too wet. No buzzer to tell you when it’s done. Have to hold button for 3 seconds to start. You can’t just hit button and walk away. Then wait for it to sense the load first to make sure it starts. Very expensive model.

Maytag Bravos electric steam dryer purchased 2009 - I have had to replace the door hinges within one year of usage at my expense. The blower belt and pulley had come off twice, the last time about a half hour after the repairman (again at my expense) left. I put it back on myself and if it comes off again, I will use Locktite to glue it on the blower shaft. I figure I will be lucky if this crap lasts a couple more years anyway. No more Maytag for us! What does it take for the consumer to get some representation with regard to lemon laws here? I will take my wrath out on Home Depot here since I have no recourse. If enough people complain, maybe they will stop selling that junk. I also will disregard Consumer Reports in the future.

Like all of the other reviews, I have had this microwave less than two years and it won’t run and reads “door open”. I am filing with the Better Business Bureau as the product advertises “partS” under 10 year under warranty when in reality it is one part with a VERY limited warranty. In order to determine if my issue was covered under warranty I would need to pay $189 not including parts in labor. I called several times and customer service indicated that they had never heard of this issue (which upon looking at this site seems hard to believe) and I would need to gamble the $189 to see if it was covered. Terrible product, terrible customer service.

Bought a maytag dishwasher 04/12/2013...have been thru 2 control panels...Now installing a third...washer works great except for that!!! Model mdb8949sbb0.

I purchased a Neptune set in the late 90s when they first came on the market. I remember my delight - after the first use my clothes looked like new. Most impressive was I never needed to iron anything. Incredible. After 20 years of maintenance free operation, I finally decided they were getting too loud and was afraid theyd break down and spill water. Of course, I bought the latest version of Neptune again. What a disappointment. These machines are terrible. My clothes come out a wadded up, wrinkled mess. I have tried every recommendation in the book - the wrinkle free, the steam fresh, you name it. I have never ironed more iron free clothes before. Its added hours a week to my chores and we all look a frumpled mess. I really regret my choice. Strange that I cant wait for these new machines to break down so I can justify a do-over.

Maytag 18.5 cu ft Bottom Freezer Refrigerator purchased 12/10/12. 1/12/16 the bottom of the freezer had an inch of ice that leaked onto the floor. My plumber chipped away ice and unclogged drains $97.50. 4/19/18) the same $97.50. 5/22/18 an appliance repair business installed a drain kit $148.40. This was his 25th Maytag with the same problem. A whole website has complaints about this problem. I sent a letter to Maytag and they wanted to send out their technician to find out the problem (with a service cost to me). With all these complaints, and a kit to fix it, they already know the problem but refuse to do anything about it. Maytag used to be a reputable company. No more. The customer service said I should have bought an extended warranty. I said a $1400 refrigerator should last longer than 3 years (the first leaking occurrence). I will never buy a Maytag product (nor Whirlpool that makes it).

We purchased a Model MDB8949SAWO Maytag dishwasher in September 2012. The control panel failed in November 2015. We wrote a letter to Maytag (Whirlpool) expressing our disappointment and received a call from Maytag customer service. The Customer Service representative informed us because we contacted our local repair facility directly, no reimbursements would be provided. During a subsequent follow-up call, I was informed by the Customer Service representative that Maytag manufactures quality products and that no premature failures were occurring with Maytag dishwashers. The Customer Service Representative stated that we should have purchased an extended warranty which lends some support to the fact that Maytag dishwashers are essentially junk. Never again will we purchase any Whirlpool products.

It took about a year for the problem, which turns out to be an extremely common problem, to start. The build up of water in the freezer due to the clogging drain. Maytag needs to step up for the consumers that purchased their defective product. I have cleared the ice and tried to clear the drain three times only to have the problem return. I refuse to pay someone $300 or more to repair this. This is crazy and unfair!