The way the outlet line and pump are set up, the Maytag Bravos does not remove all water from the bottom leaving about 2-3 inches. Even following the monthly cleaning and care has not stopped the inside of the tub from producing MOLD. When I contact Maytag there was nothing they could do about this problem. At this point my washer is only a few years old. I attempted to clean it myself but the drum would not break free. My options are, deal with the smell of mold and mildew, Pay Maytag $250 to come out and clean it (this would need to be done every 1-2 years) or buy a new washer. NOTE: I paid about $550 for this one. I have run a few clean cycles with bleach, but I think at this point the mold has embedded itself into the plastic tub.

Maytag Oven MGR8670WS1 - Purchased in the Fall of 2011 (along with a fridge... also faulty the freezer stopped working within a year). Ive had the oven stop working twice (in 2012). This week (spring 2014) would be the third time. It seems to be a faulty ignitor already replaced having to be replaced yet again. I have never used such faulty appliances EVER and never AGAIN. This is absolutely ridiculous.

After 15 months of use the Maytag Dishwasher MDB8959SBS2 the control panel start malfunction. I read very carefully about the Home Depot Customer reports before purchasing this built in stainless steel dishwasher, and supposed to be one of the top notch on the market, around $850 retail price. It becomes a big disappointment. After three months of use, the top rack handle broken but it still under manufacture warranty, so we get it fixed by Maytag contractor. Then 15 months after regular use for a family of five, the control panel start malfunction, few bottoms will not start anymore. We are out of luck with one year manufacture warranty and working towards our VISA card extended warranty to try to get it fixed.

I have a MFX2570AEM French door refrigerator. Like many others on this site I have ice building up under the freezer drawer. Water also leaks onto the floor. We keep a towel there constantly. We bought this refrigerator along with a dishwasher and microwave, all Maytag and have been disappointed with all of them. We thought Maytag made quality appliances, but my experience tells a different story. I havent called for service yet, but will later today.

Purchased a Maytag front loader and matching dryer in Sears and have had nothing but problems with both since the beginning. Now that the warranty has run out we have even more problems and doing laundry has become stressful. Big lemons. Wish I had kept my Kenmore units. Now looking into reviews for other brands, may go back to the Kenmore brand too. NOTHING can be as bad as Maytag.

Maytag Bravos 300 Washer - Dont buy this washer! This expensive washer has been the worst household appliance Ive ever owned. We bought Maytag thinking we were getting the best. NOT SO! We could have spent half the money and got a better washer. Maytag is a brand of the past. Ive had this machine about 4 years and its been a problem since day 1. There is no soak cycle but I knew that from the beginning. The problems Ive had so far are: Not enough water so items dont get wet and have to wash again, Terrible wrinkles, torn sheets and garments, items still dirty, getting louder & louder, and the most recent problem is the plastic from the top edge of the tub is now shredding and getting sharp plastic pieces in my clothes.

I bought our Maytag HE washer model #MVWC565FW back in July 2019 after having owned a Kenmore scratch and dent washer from Sears for approx 25 years, and in just one month of using it I knew it was a mistake. There are only 2 water levels - deep water (full tub) or practically no water (though there are a number of settings, there is no difference in water level, its just full drum or very very little water). The auto-sensor water level option is a joke - there is barely enough water to wash anything - its like going back hundreds of years to washing and beating your clothes on rocks. Items in the washer become so tangled it sometimes takes a while to detangle before placing in the dryer. Water stops filling the tub when lid is open - I can no longer wash and rinse delicates while the drum is filling. It took 3 calls w/ Customer Service to get an ADDITIONAL lid latch that I can use to trick the machine to thinking the lid is closed - I keep the actual lid open, then stick in the lid latch I bought - take it out when Im done hand rinsing. This also enabled to to view the washing in action - IT DOES NOTHING! Clothes stay in the same place as you placed them in the tub - they dont move, they dont wash - and I bought a washer with an agitator - that is in quotes because it is a misnomer with this brand! The wash cycles ARE SO LONG it takes all day to wash a few loads of laundry. Once you select a setting YOU CANNOT CHANGE IT - the washer empties and stops, then you have to start all over again - ENERGY AND WATER EFFICIENT...REALLY???? What a bunch of you know what! This is the most inflexible piece of junk I have ever had the displeasure of owning. I have to keep jugs of water on hand that I keep filling up to at least have a bit of water. When I called Cust. Svc. at the beginning telling them my experience - the person on the phone had nothing to contribute - they couldnt even tell me what cycles might fit my needs - they told me to go back to Home Depot and ask someone there! WORST APPLIANCE WORST COMPANY.

I have had to put two 50 lbs sacks of feed on top of my Maytag Neptune Washer to keep it from walking in my washroom. Looks like I am not the only one with this problem.

We have had this machine for too long. It starts banging and making tremendous amounts of noise. We have balanced it and tried loading it in different ways but when it starts to spin it apparently tries to even the load somehow that results in very loud noises and movement of the washer in the laundry room. Terrible machine. If we could afford it we would trash this one in a heartbeat and buy a different brand.

Purchased a Maytag MSD2553WEW00 refrigerator on 2/27/2011 from Home Depot. Began using it in July 2012 upon completion of home construction. In February 2014, after less than two years of service, the refrigerator was running but no longer cooling. After the expense of several part replacements and a service call, it was determined that the compressor had failed. Unlike most manufacturers, Maytag did not warrant the compressor and closed system beyond 12 months. The refrigerator looks like new but the cost of repair is prohibitive relative to purchasing another new refrigerator. Maytag was contacted but was not helpful.

Had it for over ten years, had no problems. We dont use the oven too often but it is simple to operate and has served us well. Easy to clean, stainless steel like looks on the front goes well with our other appliances. Reasonably priced too.

I have had this refrigerator for less than 3 years. It recently started leaking water on the floor and all over the bottom of the freezer. Repairman said it is a flaw with the defrost drain design. He thinks Maytag MIGHT have changed it since I purchased mine, but I dont know. Originally they used this small rubber valve;repairman said they get clogged very easily (even though I vacuum around it regularly and dont have any pets). He replaced that part with something sturdy that looks like a p trap. I looked online and there are loads of complaints about this exact issue with the defrost drain clogging. It cost $250 to have it repaired. I called Maytag to ask to be reimbursed and of course they will not do anything since it is out of warranty. Its a shame Maytag wont stand behind their products. Since there are so many of us with this issue, cant something be done?

First let me say I have used Maytag products for 46 years. A little over a year ago bought a new Maytag Centennial Washer (Model MVWC555DW) for a cousin which was responsible to looking after as he had been brain damaged since birth. Needless to say when I started having trouble with clothes not washing and having to bring to my home and wash was not satisfactory. This machine never worked right but until after the 1 year warranty could get by. Needless to say I will never buy another Maytag appliance but now have a Maytag washer/dryer, stove and dishwasher in my home. Maytag is Not the quality that is use to be. WOULD NOT RECOMMEND THIS MACHINE AND ALSO UNDERSTAND FROM LOWES THEY HAVE HAD A LOT OF TROUBLE WITH THIS MODEL.

The new Maytag commercial brand is different than the traditional Maytags. Uses less water. The new technology in the variety of choices for cycles and the steam cleaning for the dryer is a great feature.

I have been Maytag customers for 40+ years. I purchased a new Maytag washer and dryer at Home Depot last year. The paint is coming off and the top is starting to rust. We have had Maytag washers and dryers for as much as 17 years that did not rust. The reason we bought Maytag was quality. Rusting in one year is not quality. Please contact us ASAP. Home Depot said there was nothing they could do.

We bought our Maytag Neptune washer in 2005. We chose Maytag because of their reputation, their headquarters in Michigan, and because looking at the machines in the store, they seemed to be well built. Were we ever wrong! You would think paying $1000 for a machine would get you a product that lasts longer than 8 years! Our other washer (a Whirlpool) lasted 20 years and was still working. Im now consistently getting a 3e error code. In searching online, I found that this is a pretty universal problem and thought maybe Maytag had a recall on it. What a waste of valuable time. I did find out the machine was actually a Samsung. This seems like fraud. If I wanted a Samsung, thats what I would have purchased! Contacting Maytag Customer Service was like Land of the Stupid. After getting the runaround and being sent to a phone number and website that only covered Samsung I called Maytag again. I was put in contact with another person who could supposedly help me with the recall. Even though I told him what the problem was, he gave me the robot response about sending the GFCI plugin and told me, That should make your washer safe to operate. Seriously??? I replied, This wont fix the problem because THE WASHER DOESNT WORK and we got the recall part long ago. He then wanted to schedule a repair appointment. Not doing that, considering how stupid the Maytag reps I had talked to so far had been. Putting the hubby on the case, luckily hes pretty handy. On the upside, it was fun responding to the Maytag customer service survey that night, LOL. All of our other appliances are Maytag and they have all been great, but this washer is an unreliable piece of junk.

Sears washing machine model # mvwx500xwo - This machine is the worst. My mother who is 87 years old smells like mold every day due to the smell that comes from this machine. Im not sure whats going on but the plumber told us there is something very wrong with this machine. Its not the hot or cold water that smells, its the machine. I am now concerned about my mothers health. Please advise if you will allow us to purchase another machine with some kind of a credit due to the serious issue this machine has.

I recently purchased a Maytag centennial washer and dryer from my local Home Depot. I set up a delivery date of 2/9/12. I was contacted on 2/6/12 by a Maytag staff telling me that my washer and dryer were on back-order until 2/29/12. This is unacceptable to me. Why does your company not tell its retailers that some items may be back ordered? I would have accepted this if told when I scheduled my original delivery, but being told days later and after taking the day off from work, is poor customer service to me. I am giving very serious consideration to voiding this order and finding a new company to deal with. I do not have the confidence that future issues will be shared or dealt with in a timely manner.

Maytag Jetclean EQ Plus Dishwasher - We purchased the dishwasher in June of 2014. Recently the control panel decided it wont work. There is power to the unit. I am told that the unit is no longer in warranty so we have to pay for everything.

I purchased the Maytag dishwasher a little over two years ago (MDB6759AWQ0). This was the first Maytag product I bought and it is definitely the last one! It was more expensive, but because of Maytags commercials on what good products they had, I thought it would last longer and work better. Boy, was I wrong. When it was installed, it was loud. I brought this to the attention of Maytag. I was told there was nothing that they could do. Repair people were sent to my home several times to see if the noise could be fixed and unfortunately, it could not. This is the loudest dishwasher that I have ever had. I should have stayed with the same brand that was over 10 years old that died! Now the control panel blew out and will cost over $300 to have it fixed. After reviewing the numerous complaints that you have on your dishwasher with the control panels not working, I would think Maytag would be more financially responsible in helping the people that have your products that no longer work after being less than three years old. Just a heads up, Maytag, I will be replacing instead of fixing and not with another Maytag product!

I purchased a Maytag dishwasher model #MDB6769AWB2. After 1 year and 2 months of light use (just my wife and myself), the control panel went out on it! I called Maytag and because it was over 1 year old, they would not do anything about it! When you call their number listed in the owner’s manual, they thank you for calling their Customer Experience Center. This is an experience I can do without!

We purchased a dishwasher (Maytag) two or three years ago. We have had nothing but trouble with it. The welds on the upper rack broke. The wheels on the low rack keep falling off. Water leak happened recently. The start button broke. My wife and I decided to just get a new one rather than keep sinking maintenance costs which are going to keep adding up.

This is the best microwave that we have ever purchased. I especially like the baked potato choice. Its also very easy to use and clean. I would definitely recommend it.

I purchased this machine (MVWB765FW0) because I had a good experiences with Maytag in the past. There is a manufacture defect in this particular machine. If I were you, I would not buy it. I’ve lost two sets of bedsheets and my wife had a dress that she loved that got ripped up at the bottom between the agitator and the base of the machine. Maytag knows about the problem and does not have a solution.

We purchased a new Maytag dishwasher for $500 from Home Depot about 1 year ago... it stopped working 4 days ago. I did not get satisfaction from Maytag customer service as they tried to sell me a repair program whilst I was trying to determine if it was under warranty as it is a known problem. I now have a repair person coming out with a price of $189.95 + time. A complete joke of an organization. Lesson? Do NOT purchase any MAYTAG brand. They DO NOT stand by their product. My rating is ZERO STARS, the site forces me to enter a star which is ONE TOO MANY. I will NOT do business with Maytag, Whirpool or any of their brands again.

My 6 year old Maytag 3000 series front load w/d set started leaking after 2 years. Minor leak on certain wash settings such as Rapid Wash setting that worsened (and I could live with), so that setting wasnt used. Last month the washer door was flapping open DURING a spin cycle. I stopped machine only to find the entire barrel had dropped and metal wire wrapped around clothing. Worst washer ever!

Bought a new Maytag Over the stove model Microwave from Lowes. It worked fine for a while. Then it started saying open close door. We opened the door and closed it, and sometimes it would work. This went on for a while till it finally would not work at all. Called for repair, the service guy came and took it apart and one of the door switches needed adjusting. He left and it was working, good deal. 2 days later open close door started all over again. We found if we lifted the door when closing it, then it would work sometimes, until one day it would no longer work. We called for another appointment, and got a new company to fix it called ABCO. The service guy showed up and tightened a screw and it worked again, said the other service guy might have forgot to tighten it down. I tried it and it worked. We did not touch it again till next morning and back to open close door again. Called ABCO back and got a new service time for Wednesday next week. Wednesday came and went, called to see why no show. They said we were not on the service list and were very sorry. So we set up a new time for them to show the following week Tuesday between 12 and 3 pm. At 3:49 they called and said sorry, but they were not going to be able to make it today. I told her then get us tomorrow and was told they were very busy and maybe Thursday would be better. I told her we were in line and and should get service before others that came on later. Her reply was maybe Monday of next week was better. After the runaround she said they would try for Wednesday tomorrow, but no promise made. After that I called Maytag direct and they said nothing they could do except make another service appointment. She told me I could get a service appointment tomorrow Wednesday between 8 and 12am or 12 and 3pm. I asked with who this time and was told ABCO who just told me they were too busy to show up tomorrow and had put me on standby. In the meantime I paid over $300 for the Maytag microwave that is never going to need service because the Maytag service man is so lonely. And bought a $ 200 Panasonic counter model so we could have a working microwave. So now we are in over $500 and still no Maytag working microwave. They did send me a letter offering me a discount on extended service plan if I want one. I told them it would be cheaper after the one year runs out under warranty, to just junk the microwave because it has cost me way more in wasted time, waiting for the lonely Maytag repairman to show up. Bottom line do not buy a Maytag Microwave model MMV4205DS-1 unless you just want a good looking decoration over your stove with a nice light, and have plenty of time waiting for the lonely Maytag repairman.

The machine had automatic fill which did not allow enough water to rinse the clothes properly. I had to run another cycle to rinse the clothes. The machine was also extremely loud. When I had a warranty repairman come out concerning these two item as it was brand new, I was told I should have researched better. I gave it away after 3 months.

I have a bottom freezer Maytag refrigerator that is about 4 years old. It started leaking and continued to get worse fast... It appears that the gasket around the freezer drawer does not seal about half way up. It causes a sheet of ice inside the freezer, so I am not sure if it leaks due to the ice defrosting. The refrigerator doors do not seem as if they shut tight either. After reading many of these comments about Maytag refrigerators, I am not sure at this point if it might be better to buy a new one rather than fix this one??? I looked for a recall and do not see one. Clearly this is a defective appliance.

I asked a simple question online to see the location of the lint trap on my washer, I had read my manual and could find nothing about the lint trap, and to get a simple answer as to location, they wanted to be paid $30.00, I dont want them to come and show me just a simple answer as to where I could find it. It should be in the owners manual but it isnt

We purchased our Maytag through Sears. We wanted a very basic machine, and thats what we found at Sears, yay! Fast forward eight years and it suddenly quit agitating. We tried fixing it ourselves by replacing a plastic gear part, which, later on our appliance technician said was totally logical, but it still wouldnt work. We got our appliance repairman out here and he took it into the shop and fixed the problem, which turned out to be part of the motor or something like that. The thing that bothers me the most is that he asked if we had bought a refurbished washer, but we hadnt, it was brand new. He gave us a part that was swapped out that wasnt made for the machine and also said the safety guard for the cord was missing. This keeps it from pulling out of the machine in case it gets jerked. I feel deceived and just wanted to vent because there really isnt anything I can do about it now. Buyer beware, yes, but I know we have to be our own technician sleuths to be sure were getting what we paid for?

Worse washer ever, clothes are dirty and smelly. Customer Service is even worse. After a normal cycle clothes come out half wet, never enough water in the machine. Everything gets washed on bulky and there is soap residue on everything. Have taken clothes to the laundromat on several occasions just to get them clean. I cant wait to get rid of this piece of crap!!! Never ever buying Maytag again!! Warning to everyone... DO NOT BUY THIS MACHINE!! And with the extended warranty, they still dont cover it. :(

We purchased the MMV4205DS over the range microwave in June of 2015 & installed it in July the same year. We purchased the matching range & a dishwasher at the same time as they were running a promo of $150 rebate if all 3 were purchased. They denied us of $50 of the rebate & stated that all of the paperwork was not submitted on time. We received rebates on 2 of the appliances & paperwork for all. 3 were in the same mailing. Hmmm. We were told a 3rd party handles their rebate program. So much for taking ownership. Yesterday the door open message appeared on the control panel of the microwave & now there is nothing; no light, no fan--completely dead. So much for buying American. Maytag does not see that this is a problem? Do NOT buy Maytag!!!

I bought a Maytag Bravos from Home Depot back for around $1000 in Nov. 07. After 3 yrs, the whole tub assembly had to be replaced but I had bought a warranty so that was taken care of but it was out of service for about 2 months while I waited for parts. Now every time I use it, I get the OL on the control panel and it wont spin without getting out of control and stopping. Washers in the past have lasted me at least 15 yrs and cost less than half that much. I will never buy another Maytag ever. This is what happens when companies merge and quality is no longer important. I think the stock market ruins companies. Im currently looking for the best quality, large capacity washer on the market. I will pay more for quality but thats what I thought last time.

I had a 1 1/2 yr old front load washer. I was worried the filter might have a lot of dog hair in it so I called to just have it looked out. I couldnt remember if I had an extended warranty. Thought it would be listed with Maytag. They said no. I said OK. They recommended A+ to come out and said it would be $60.00. That was OK because I wanted to prevent any problems with the washer in the future. I thought them checking it would be a preventative measure. The tech came out opened it up said there wasnt much hair or any other problems. Put it back together, plugged it in. There was a Big popping noise and smoke! Washer no longer worked. The man said doesnt make sense but he would fix it and not charge me for parts etc. I called Maytag. They refused to do anything since it was out of warranty even though they recommended this company and there was absolutely nothing wrong with it in the beginning.After about 2 months he still couldnt fix it. About this time I found papers for a warranty with the Home Depot. The repairman said he works with Home Depot as well. Told me to contact them but I needed to pay $120.00 to him and file a claim and then he would fix it. Apparently he does not do service work for Home Depot. They sent out other repairmen. They tried to fix it but apparently it was deemed unserviceable he blew the mother board. Home Depot said they would replace or reimburse me the amount I paid for washer. Then a machine called said they were sending me a check. We will probably never buy another Maytag! Even though I want to buy American if they wont help or stand behind their products. I now have an LG we bought from Pacific Sales with a cheaper warranty and much better customer service.

Bought Bravos XL washer and dryer about 4 years ago at Home Depot. The dryer is fine. The washer not only doesnt clean the clothes unless you have it on rapid wash - but every person that is here when I wash clothes is shocked at the noise coming from it. I always say my laundry plane is landing or taking off. Its out of control.

Maytag junk MFW2055FRZ00. We had to replace our reliable 15 year old Frigidaire side by side fridge when it failed due to a compressor failure. We should have pressed the service company to replace it or found someone who would. We were limited in replacement units because of built in cabinets, thus a smaller French door (so we have to open two doors rather than one) Maytag. Perhaps our 30 year old Maytag washer and dryer made us believe Maytag still offers high quality products. We were wrong. Everything about the unit is poorly designed, cheap and flimsy. The freezer drawer pulls out unevenly and the ice maker is primitive. Above all no matter what appliance you choose be sure there exist factory authorized servicers in your area otherwise warranty issues are a problem.

We bought the Maytag Washer and Dryer set about two years ago from Home Depot. We have had to have the washer repaired several times in that two years, most recently for a cracked mother board controller unit. The same day we had to have the washer repaired, we also had to have the dryer repaired. Lint and dust is not properly filtered out by the filter and accumulates inside the dryer where it should not be, up against the gas heating unit. The repairman indicated that it was badly scorched and that we were lucky it had not caught on fire. Another customer of his had the same unit, which burst into flames one day when she had left the house with the dryer going, causing a house fire. The quality of these items is highly questionable. Having to spend nearly $600 to replace a cracked mother board only two years after purchase simply is unacceptable.

I purchased a Maytag model 4000 Front Loading washer in April 2010 and in May 2011, the tub bearings went out which is a $600 repair. Now in January of 2012, the tub bearings are going out again. Neither Lowes nor Maytag are willing to do anything to remedy the situation. Do not buy Maytag and do not buy from Lowes. Their major appliance buyer has to know about this and continues to retail a product not fit for its intended purpose.

My Maytag 3000 series washer had to be worked on right after we purchased it. Now it stinks and is leaking. Repairs are going to be over 300 dollars. A part wore out. It should have lasted longer and why does the front loading washer stink. There is no door to open to clean the filter.

We have had this washer for 1 year. I noticed right away my clothes would come out extremely wrinkled. Now not only are they wrinkled, they also smell musty. After researching I find others have the same issue, even finding a video of horrible mold under the drum. We called to have it serviced since we have a 5-year warranty. The service man recommended using Afresh. WELL, we do faithfully every month. He said they would not pay to have it cleaned, and even if he cleaned it, that the mold would come back. This to me is a major design flaw, one that could potentially make people sick. IF there is that much mold growing in the machine, with no way of cleaning it, and now the clothes are smelling, there is a HUGE issue!

My refrigerator stopped working less than two weeks after purchase. The ice maker failed to produce ice. I feel they sold me a lemon. Yes, I do!

I bought my Maytag Model LA608 washer in 1976. It has very few electronics and a mechanical timer. It has been used every week since then for 2 or 3 people. It has had 3 problems in its lifetime. I replaced the 2 valves that control the hot and cold water entering the machine. I replaced a small plastic sprayer part. And last year I replaced 3 clamps that rusted and started to leak. Thats it in 40 years. I was able to open up the front and back covers to get at the parts quite easily.It is a simple machine with almost no electronics to stop working. Nothing bothers me about the machine. Its simple and wonderful. When it finally breaks, I will try and find a good sized machine that washes permanent press and regular clothes, has a controller to select hot/cold/warm water temperatures, has a regular and gentle cycle, and has 3 load levels for the water to be used. I will try to find one that is good quality with few electronic parts. I will not buy a high efficiency model that uses less water as I am on a well and water shortage is not a problem where I live. I will not buy a front loading model.I would not buy a machine that has options that I do not need. I would hope to find a quality machine similar to what I have now. I would read as many ratings about the various models before making a selection and then I would cross my fingers and hope for the best. If it is possible, try and find a good quality machine that will be dependable over time. Buy a basic machine with only the options that you really need. There will be fewer parts to stop working.

Its about Maytag MDE7600AYW Atlantis electric dryer issues, Nov 2005 model. There is an obvious design flaw. I have replaced the automatic dryer control board twice since 2005. The unit simply never shuts off, or cooks your clothes for 2 hours. Who will recall this unit and fix the circuit? They will not admit their error.

Read MANY complaints about these units leaking water onto the floor underneath. This is accompanied by a sheet of ice forming on the bottom of the freezer under the main drawer. Good money says the cause is a plugged drain tube. I had a Subzero that suffered a similar problem. The factory installed drain tube was a flexible coil type and food particles would be easily caught, compromising water flow - leading to an ice plug and eventual evaporator ice-over. I replaced the factory tube with 1/4-inch rubber fuel line and the problem went away for good. With the Maytag units, if memory serves, access to the drain tube is from the back of the unit. You have to remove an access panel to get to it. There is typically a small removable rubber restrictor cap on the bottom of the tube; this is the most likely spot for a clog to form. Due to its design, IMO, clogging and ice-over will probably be a periodic thing. If you are really handy, you can do this maintenance thing yourself.

Maytag washer has increased my water bill; it was supposed to be energy efficient! Also, the washer will not wash a blanket. Sensors will move a large item to one side causing an uneven load which then causes numerous extra fills until stopped manually. I was told to add more items! A blanket barely fits in the tub. I had to invest in lint rollers since the rinse cycle is inefficient. This washing machine is useless. I should have stuck with Kenmore.

My wife and I bought the Maytag commercial Bravo set about 5 years ago and both the clothes washing and dryer machines are still working as great as the day we bought them. Im a bit biased though as I bought Maytag commercial products in the past and will continue to do so because its they are a dependable company made a reliable machines.

Purchased Maytag dishwasher from Ft Knox Exchange in 2011, Model MDB6709AWW1; Serial # F04117463. Like most posts before me, the panel started failing after 2 years. Unit is now inoperative. I am attempting to fix myself using repair techniques Ive found online as I refuse to pay hundreds of dollars to repair this piece of junk. Will never buy Maytag again.

Please read Michael of Davenports review. I read it and word for word this is my experience. This washer is the worst Ive ever had. If I could get back my old 20 year old machine, I would trade it in. Dont buy, youll hate it.

Maytag Dishwasher MDB7749SBW03 - We purchased this dishwasher in 2013. About 1.5 years after purchase the control panel started to get flaky and different settings wouldnt work. Not long after that it stopped working at all. I did some troubleshooting and found that the ribbon cable that connects the control panel to the control board was corroded due to water/steam getting to it. Since we were past the one year warranty I bought a new control panel and things worked fine for about a year, now the panel is going bad again. I contacted Maytag and they said they cant do anything to help me. This machine is not even 3 years old and going on its second control panel. I would recommend staying away from all Maytag products.

We purchased a $500.00 Maytag dishwasher, Model #MDB7749SBW, in August 2013. In December 2014, a little over a year of owning it, the pump failed. We called Maytag and they had a service company come out and replace it. We paid $181.00 for this service call. In July 2015, the control panel failed so we called Maytag to see if they would replace it at their cost. All they are willing to do is to send another service guy out at our expense. The service call is $89.95 and that doesnt include the labor! The total with tax will be close to $200.00 again!!! Now we are getting close to spending $1,000 for this piece of junk! In addition, this dishwasher is only used three times a week because there are only two people living in our household. It is obvious after reading the other complaints that the control panels are defective and I am sure that Maytag is well aware of this issue. So, buyer beware. Dont even consider purchasing a Maytag dishwasher unless you enjoy watching your money flush down the toilet. They dont even deserve a 1 star rating!!!

Maytag washer Purchased December 2016. Washer is very slow: runs 1 hour plus. Wash takes a VERY long time. Small load only. Heavy loads go to Laundromat. Maytag does not clean clothes, always MUSTY smelling. Cycle OFTEN does not drain tub And forced to use Drain, Spin cycle to drain tub. Wrinkle cycle ties clothes in knots. Using AFRESH to clean tub makes no difference in foul odor. One service call, error codes found, computer reset. Repairman said that the MACHINE WORKS AS DESIGNED. Repairman said that any tiny bit of debris can cause washer to clog and fail to drain. At best clothes always wet, slow to dry. My old Whirlpool washed any sized load. Clothes always clean and fresh. I used laundry only when we had power outage. LIKELY WILL PUT THIS ON THE CURB. I DO NOT RECOMMEND THIS MACHINE.

I have bought 2 high end top loader models (Maytag centennial commercial), brand new both from Home Depot. The problem is Maytag is making them cheaper! Suspension is coal springs that suspends the load so if you fill it up, it lowers the drum to the floor, instead of a bottom bracket that supports the weight from lowering the drum to the floor! Second is the pulley system with the belt drive that wears through the plastic casing. You know some people dont have $900 or $1,000 for a machines that says commercial or heavy duty that only last 4 years when you have a family of six! Very very sad, will never buy another Maytag.

Like many people here, I have a Maytag Dishwasher Model # MDB7749SBW3 Serial # F40107007. We have had this dishwasher for about 12 months to 18 months. The first indication that there was a problem was some of the lights were acting strange. Then the dishwasher starting going nuts. I removed power from the unit thinking that maybe the controller became confused. The problem persisted. I would hit buttons and either nothing would happen or something completely different would happen.I take the dishwasher door apart and remove the touch pad. I notice some discoloration on the ribbon cable. I remove the glued on front panel to look at the electronics behind it (see pictures) and I see some discoloration there as well. So using my multimeter, I find that there is a direct short between pins 4 and 5. I vigorously flex the cable at the point of discoloration and the short goes away. So at this point, I doubt that I can get just the flexible circuit strip so Im going to have to pop for a new touch pad assembly. I didnt go further in the measurements as there was no point since I already detected one failure. Furthermore, I inspected the computer control unit and I did not see any obvious signs of corrosion or discoloration anywhere on the processor board. So it appears that there is no problem with it.Conclusion: Many people are at a disadvantage when it comes to electronic devices. In my professional opinion, this is clearly a failure of the insulating material of the ribbon cable due to environmental contamination. Visual inspection shows that corrosion of the conductors is clearly evident. About Me: I have been an electronics technician on and off for over 20 years now. I have a 2-year college degree in electronics technology and I am currently in school to become an electrical engineer. In my house, when something breaks, I fix it.

The worst wash machine Ive ever used. It doesnt clean clothes well. It constantly had error codes. Im constantly having to unplug and reset the machine and 4 times out of five it will NOT restart. Not to mention it stinks worse than my sewer. I have to run the refresh cycle every four to eight loads. Ive owned this machine three years. And it has been three years too long. I will go back to a ringer washer or a wash board and have better results.

My freezer has been leaking from the bottom for a few months and now the icemaker has quit working as well. The refrigerator has been purchased less than two years ago. The warranty is expired. I will not fix this refrigerator, as it is a gigantic piece of junk. However I would like to be compensated by Maytag at least 1/3 of the price so I can have it removed from my house before it creates more damage to my floors and subfloors.

Leaked and leaked, spent hundreds on never ending problems from day one. No support from Maytag. I was told by Sears salesman it was the best you could buy. Our old washer lasted 30 years. This one never worked right - dead at 5 years. Shame on Maytag.

Just like all the other reviews, 14 months after purchase and 2 months out of warranty the control panel on our Maytag Dishwasher stopped functioning. The “10 year warranty” is a joke a covers 3 things. We had model MDB4949SHX, $550 new.

We purchased our Maytag dishwasher (model MDB7609AWW2) on November 14th, 2009 from a local appliance shop in White Plains, NY. Total purchase price was $449, not including tax.Sometime in November of 2011, the unit stopped working. I tried every simple test I could think of to hopefully reset the unit. Finishing the obvious checks, I researched some possible problems on the internet latch micro switch, drainage problem, dirty latch, etc. Frustrated as nothing got it working again, I called a repairman recommended to us by the appliance store.The repairman charged me $75 for the visit just to tell me that the control board is shot. Even worse, and this is the reason for this letter, the part costs $329 plus $40 in labor! That is outrageous! If you do the math, I am facing the costs of a brand new unit to fix the old one. That might make sense if the unit was 8 years old but it is barely 2.I have sat on the decision now for a few days as I am beyond upset and I never make good decisions when I feel like this. But to recap, Maytag manufactures an appliance where its basic function - turning on - fails in 2 years and the repair cost essentially totals (to use insurance parlance) the unit. I find this absolutely unacceptable.I don’t expect Maytag to do anything for me. But I will say this; I plan on letting everyone I know just how this experience went. To make things worse, I am willing to pay for a quality unit but how does anyone know what that is anymore? For color, my grandmother has a KitchenAid dishwasher from the 1970s that is still running fine. No membrane controls, no delay functions or fancy BS super sanitary cycles and guess what, it has no control board, just plain old dials and buttons. Imagine that mechanical control? Built to last unlike the junk you see today.To remedy, I plan on picking up a used machine from the classifieds. I’ll install it myself and be able to do this for 9 years at $449, assuming it only lasts one year (I’m finding these units for $50 used). I may get lucky and find an old one from the 70s that will last a lot longer than that.

I purchased an emerald green washing and dryer (MHW4200BW) by Maytag. Unfortunately, my washing machine broke and I bought the extended warranty. After many visits from the repair company, it was determined that one of the parts needed was on back order indefinitely. Maytag decided that they would replace the washing machine. Sounds like a fair and good deal, however, the washing machine that they are going to replace my unit with is of a different color. Apparently someone in upper management at Maytag made a business decision to stop selling this particular color unit with little to no regards to the customers that had already purchase their product in that color. Had I known that they were going to discontinue the color, then I would have stuck with a standard color like white. At least I would not be faced with having a mismatch unit now because Maytag will not replace both units. To make matters worse, my washing machine and dryer is on the first floor right off my kitchen. It is not stuck in the basement way from company, etc. I am so disappointed in Maytag and their lack of consideration for their customers.

Bravos XL washer- This is probably the worst purchase I have ever made, first off, at $1000 it was a pricey purchase however, I chalked it up to it will last many years without issue. After only 3 years, the unit leaked water and was so loud you couldnt stay indoors while it was on spin cycle. The bearings and seal were completely shot and needed replacement, after the sticker shock of having a good repairman fix the problem I decided to tackle the job myself. (Thank you YouTube). All was well for the next 2 years until it all happened again. Maytag is junk and will never get another dollar from me-ever! A Speed Queen TR5 now sits where that piece of crap used to reside. BUYER BEWARE!

Bought a Maytag bravo xl washer and dryer two years ago. Spent around 1,500 dollars. Didnt make it a year before things started going bad on them. First the lid lock on the washer broke. I got the lid lock pulled out far enough that I could drill a hole in it and tie some thread to it to pull it out when the washer was ready to lock. Today the piece of junk just quit. Not long after the junk washer started messing up the dryer starts sounding like a fork in the garbage disposal. It still works and dries the close but you hate to even turn it on because of the noise. I will never purchase anything maytag again in my life. JUNK!

I have had this washer (top loading washer model MVWX550XW0) almost 2 years. It has ruined some of my clothes. It does not properly wash anything. I have tried every possible solution. I cannot use the HE powder detergent - it will not rinse out. I tried using less than required and double rinse, absolutely did not overload. Even using the HE liquid still did not get clothes clean. I used the number one detergent to the cheaper brand - it makes no difference. I still have to double rinse everything. Small throw rugs will not even get totally wet or clean. I took clothes to the laundromat just to make sure it was the washer. It is this washer. I know I have waited too long to register my complaint, but I have basically thrown away $1200. Also, loads of clothes would take up to 1 & 1/2 to 2 hours to wash. Now that is definitely not energy efficient. I would love for you to pick it up and bring me a standard washer and dryer. I work for a research firm and know when companies really care about their customers. I will be interested to see if the Maytag Man really cares. The only reason I did not check angry is because of my delayed response.

I own my oven for 10 years. It still looks brand new. The bottom oven went out and they do not sell the replacement parts anymore. I think its terrible that I had to go and buy a new oven when mine still looks brand new.

We have owned the dryer (Maytag Bravos) since Dec. 2010 and are now on our 4th service call. Upon the second delivery of the part that was ordered last week - we will be on the 5th service call. I finally asked Maytag if I could get a trade in since this dryer is obviously crap. They said they could only handle the problem at hand, which is the same problem over and over and over. The flywheel was left off all together. The pulley belt for the dryer pops off about every 4 to 6 months. Ridiculous. Its a crap dryer, dont buy one!

We just had the same problem as most of you have posted. The control panel malfunction. Model MDB7749SBM. Our issue started after only 18 months when the dishwasher would start on its own and/or cancel a wash on its own. I think this is a major issue if a home appliance can start on its own from the off position and run through multiple cycles. I think this could be dangerous if you are out of town. Our cost to replace the panel was more than 1/2 of the original purchase price. This is a major defect and should be handled by Maytag if they are a company with any integrity.

My built in electric double wall oven, Model MEW6630DDB, convection on the top, has been the most frustrating appliance I have ever owned. It has never kept an even temperature. It has been repaired several times and still does not keep an even temperature. It takes 14 hours to cook a 20 lb. turkey and baking cookies are not even an option. I have complained to Maytag and have paid for repair services. Their solution buy an extended warranty which is absolutely insane because they havent been able to repair it since it was new over four years ago.

We purchased a Maytag bottom-freezer refrigerator MBL2258XES1 from Home Depot on 12/30/2011. Other than being a bit noisy, it functioned without problem for a little over two years after which we noticed water pooling on the floor, just below the left-front corner of the bottom-freezer door. It was shortly thereafter we noticed the large sheet of ice that covered the entire floor of the freezer. Over the past several months I pull out the large towel, my spatula, my meat tenderizer and break up and lift out the ice onto the towel around every two weeks. Thanks Whirlpool/Maytag! At least that Maytag repairman isnt lonely anymore.UPDATED ON 03/18/2015: I called Maytag Customer Service, (800) 344-1274 to discuss remedies for my Maytag/Whirlpool bottom-freezer refrigerator which has a perpetual layer of ice on the floor of the freezer which leaks onto my floor. I was offered a product called Repair Plus One which includes parts and service for this repair and they throw in a 1-year warranty. The cost: $359.95. The representative informed me I only had 24 hours to make up my mind as the offer was time limited. I asked if there were any other remedies available to me and she said none other than a service call.

One time at around yr 2 of our 10 yr warranty the repair guy removed my agitator, spline gone. Couldn’t find one anywhere! After a month of using a laundromat, I called the company in Montreal and they had the new agitator in my post office in 4 days. I am unable to wash anything that puts the Bravo washer out of balance ie: towels. The sides are busting out on the machine!! We have only had it 4 years so far. Not impressed! Does the warranty cover busting out sides? As it is a major part of the structure of the machine.

Purchased a Maytag Bravos washing machine. DO NOT BUY THIS MACHINE. Disaster as the cycling is hit and miss. The clothes can take 4 hours or more to wash a load. And even then the clothes may still be soaking wet. Grandmas old wringer washer was better. DO NOT BUY MAYTAG. DO NOT BUY MAYTAG BRAVOS.

I have two major issues with my stove. First is that you have to press enter after setting an oven temperature and it doesn’t even beep to remind you before just cutting off. Older, forgetful people like me have probably prepared countless dishes for the oven only to find that it is not preheated. The second is that if you turn on the timer, it cuts off the oven. You only make that mistake once before writing the timer off as useless. I have a hard time believing that they ran either of these by anyone who cooks! One other mixed feature, the heating element for the oven is below the floor of the oven. This causes it to preheat slower - which compounds problem #1 - but makes cleaning a breeze.

I purchased a Maytag stainless steel French door model the middle of 2006. While cleaning the French doors with the cleaning product given to me with the purchase of the new fridge, I notice what looked like coffee on the doors. It wasnt, it was rust on the stainless steel doors. I called the service tech and they came out. Rubbing the fridge, he told me it wasnt rust. He took a closer look and found that it was in fact rust. He called his office; they told him that rusting on the doors has been an issue lately. He charged me $65.00 for what I already knew. I called Maytag and it took a while, but they decided to send new doors. However, I had to have a Maytag rep install it, which would cost me. I didnt have it done. Two years later in 2010, the French doors felt hot to the touch and the inside was warm and not cooling. The freezer was fine. I called for a tech to come out and it’s another $65.00 to fix a fan motor that blows cool air from the bottom to the top. Oh, it’s not under warranty because it wasnt inside with the motor. Total cost: $235.00. In 2010, I woke up and opened the fridge to get milk out. It was warm and so was the inside of the fridge. I thought it was the same problem, but the freezer also was warm. Upset and not wanting to pay for this again, I unplugged the thing and started using a little fridge that I have stored in the basement. It has no freezer. Today, I finally got over being pissed and decided that I would have a tech come out and find out and finally fix it. The tech said that the compressor has failed and it would cost $790.00 to fix. Im not having it fixed, so it’s another $65.00 gone. The tech said that the compressor in Maytags/Whirlpools has been a pretty big issue lately. All I can say is that I will not ever purchase Whirlpool products again. From inside to the outside, this product has been unsatisfactory. I just noticed that the rubber is failing on one of the French doors. Wake up, Whirlpool. Model number is MFD2561HES.

I bought this large capacity top loading wash machine about 22 years ago and it has yet to fail me. It had never needed any repairs and cleans my clothes wonderfully. The brands reputation is well earned. Great washer!

Maytag washer was bought May 2010 with an extended warranty, which expired May 2014. This machine was used by two people with average wash loads. Five months later the machine computer programming didnt work and the machine sounded like a jet taking off. Whirlpool said a one-year warranty would cost $329! This would have been less expensive than a new machine, but I felt I couldnt trust having it repaired. A repairman very familiar with Maytag products said he had three service calls the same day with similar complaints for the Bravos 300 series. He told me the bearings were bad and the cost to fix was not worth the money and this machine should have been recalled. I bought another brand and will not buy Maytag again. When my new machine was delivered, there was grease on the floor from the Maytag.

I purchased a dishwasher and stove from Home Depot. Stove has already been replaced twice because of faulty manufacturing and now the dishwasher, after 1 1/2 years no longer works due to the control panel. I called a repair representative of Whirlpool/Maytag and explained the circumstances. Their own customer service people indicate that it is cheaper to replace a product then it is to repair it. Shame on Maytag and Whirlpool that they move their companies to countries outside of the United States and they no longer stand behind their product. Shame on them that what use to be the best product around is no longer worth paper you print on. I will no longer purchase any product from Maytag, Whirlpool or Home Depot since they all seem to line their pockets from products they know wont last. One mouth is worth a thousand complaints and I plan on screaming from the rooftops!

I bought a brand new refrigerator and about four months into using it, the freezer door began to become loose and opened by itself automatically. It also started to leak so I called the company continuously looking for a solution. However, they never resolved my problem. The company sent a technician. However he was unable to fix the problem. The technician said it was fine and did absolutely nothing. And now I am still waiting, but now your company says my warranty is up EVEN THOUGH I called much earlier and your company did NOTHING to help me. I need someone who can handle my problem. Ive been using your products for many years, and have always been satisfied by it. But this refrigerator has changed my perspective. I hope you give this a peace of mind and treat your other customers better.

When my house burned in 1995 I purchased all Maytag appliances when we rebuilt because I had good performance from them up to then. My washer and dryer even made it through the fire and are still going now 14 years after the fire. They are 34 years old. The other appliances I purchased were a chest freezer, dishwasher, stove, and, a refrigerator totaling around $2,000, a pretty sum in 95. I have nothing but good to say about the freezer and the dishwasher, however, the refrigerator and stove stick me in the side every time I look at them. I purchased a smaller refrigerator than I had planned because I was PROMISED that the refrigerator was designed to hold the milk in the door. The first thing that happened when I opened my brand new refrigerator was the shelf holder broke and the milk fell to the floor making an awful mess. They ordered the shelf holder assuring me it was a fluke and sent me on my unhappy way. After I got the part I installed it and crack-smash-pow-swoosh! It happened again! I called the store I purchased it from and they said they ordered extras so to come in and get them, that I had probably installed it wrong. Went like this and I finally told him like I told him at first I do no want this refrigerator! You said and the pamphlet says it is capable of holding a gallon of milk in the door. It does not. It cant even hold catsup bottles without breaking. Thats when he told me that yes, they were having an issue with this refrigerators door shelves. He then gave me the rest of the shelf ends he had and said after that they were gone, they had discontinued them. Also said I was past the days to trade my refrigerator. I told him that was because he kept stalling me, ordering parts. LEMONS AND LIES. Now the refrigerator sits in my laundry room, freezes food in either section on its own whim, and the shelves are held on with DUCT TAPE. I have multiple correspondence with the company but gave up as I was seriously hurt in a vehicle accident and had to put my energies to surgeries and healing. And dont get me started about the stove. I will not be buying Maytag anymore.

This Maytag oven has lasted my mom for over twenty years. Now after her passing the oven is now serving me and my family. Have had it soon to be three years. Just now having to replace one of the eyes.

I bought a refrig from Home Depot on 10-16-2012 two years ago and it doesnt work, but they only put one year warranty on. So had to go out and buy another. My complaint a refrig should last more than two years but they were going to send repairman out on my expense and more than likely would of cost me the price of a new one.

I emailed Maytag https://www.maytag.com/contact-us/ about my model number MBL2258XES3 Fridge on Dec 31. They scheduled a local appliance repair company and they came out today, Jan 5 and did the repair and defrosted the compressor and freezer compartment. 45 Mins is all it took. Thanks Maytag.

My husband and I purchased a brand new Maytag dryer in January 2012. Our first issue came when the sensors went out in March; then the belt slipped off the drum in June; then the thermistor was defective in July; and now, the same thermistor code has popped up twice since replacing it. I cannot afford to go to the Laundromat all the time thats why we bought a new dryer. Please give me a refund so that I may buy a different brand. Model number: MGDB850WR0, Serial #: M10301051

I started hearing the Maytag Microwave MMV4203DW00 beeping this morning after breakfast. I had not used it since the night before to heat up soup in a Corning Ware bowl. Its doing that 5E thing and nothing on the control panel works. Ive unplugged it, waited, plugged it back in and the same thing. It starts off saying Select Clock and 5E and then stops on the 5E. I bought this in Aug. 2010 and it is vented out the wall. Of course, that doesnt work now. The metal rack has never been put in it. Im single and the only one who uses it and I dont use it very much either. And this model only got the one 40-watt regular bulb over the range - lousy. And it doesnt work now either. And the control panel lights up orange. Had I known that, I would have never bought it in the first place. Of course, the stupid orange 5E lights up. Im unplugging it for good. Its not worth fixing. Do not buy this microwave!

I have had my washer and my dryer (model no. MGDB850WQ - serial no. MJ3311087), for 1 and 1/2 years. I have given both plenty of time and since the beginning, I have literally hated these products. This was a large purchase, so I feel locked into a terrible choice. I wish I had never bought these two items and will never use Maytag again. I will also never recommend these products to anyone. I do not like the new technology.

I purchased Maytag fridge a year ago and it has been a nightmare. The freezer doesnt freeze items. the drawers were all damaged upon receiving. I have contacted Maytag for more than 10 times and 5 techs came that I paid 125 each visit to fix the fridge because I didnt purchase the warranty thinking it was a good product . It is not! They dont stand behind their word. They lie and they send unqualified techs the misdiagnose issue to collect service calls. Please avoid this brand by all cost. My experience is terrible and I never want to wish it on anyone.

We received our new Maytag washer MHW8200FC on Saturday 11/18/17. We washed 2 loads on Saturday and on Sunday it didnt start. Not only did it not start but it was locked with clothes in it. We finally got it to open but it wouldnt start to wash. We had the distributor, Warners Stellian, schedule a service tech. He came out on 11/21/17 and determined the board was bad and that he would order one and be back on 11/29/17. A week without a washer doesnt work for a family of 5. This isnt like a lawn mower I use once a week, we use it daily. Whatever happened to quality control? A brand new expensive product breaks in 2 days? Maytag says its Made in the USA, which Im all for... Only if it works. USA or China, broken is broken so I dont care where its made. Whether its planned obsolescence or just a plain faulty product, Maytag is now another brand that I will avoid buying in the future.

Three years ago, we purchased a gas Maytag double oven, it worked fine for three years, then it blew the breaker. When we turned the power back on, we could not turn the oven off. The control panel had to be replaced, dinner too. We had bought the extended warranty, so that was covered. Last week, after four months, it happened again. We placed an oven thermometer inside the oven and it is was higher than the maximum temperature of 600 which the thermometer could measure. We are currently awaiting a new control panel. Maytag used to be a good name, but recommend you to buy something else.

Purchase brand new range a couple of months ago. Self-clean oven does NOT self-clean and leaves weird, flakes of something that stick to oven floor. Burners are inconsistent and difficult to control heat level. Take forever to get warm, and then either boil over or wont get warm enough. Purchased this with inheritance from my mother - how sad! Always had such faith in Maytag.

Purchased washer March 2017 and had to get it repaired twice by the end of 2018. The top loader even with agitator does not clean clothes very well. The repairman said not to fill the washer above halfway so I can only wash about 4 pair of my husbands heavy soiled work jeans. I won’t buy another Maytag.

We bought a Maytag dishwasher in May of last year. The control panel went out about 3 months after we got it. It just started doing its own thing Like not running the wash cycle or a different cycle than we pushed. We called for a repair and were told by the repair man that the control panel was on the fritz. He ordered a new one and told us it would be a month before he could come back and install it. When the control panel showed up at our house, we installed it ourselves because we did not want to have a faulty dishwasher running in the house.Just yesterday we noticed a huge rusty area on the bottom rack. We called and were hold for 20 minutes if not more, before we were even able to talk to a rep. She then came up with every excuse as to why our rack was rusty (hard water, water changing??). We asked for a new rack but she wanted to send a repair kit. We were on the phone with her for half an hour, if not more, and she just refused to send a new rack. When we finally asked to speak to the manager we were told the wait time was 32 minutes and hung up! Do not buy crappy Maytag appliances with even crappier customer service reps! (see our review about our Maytag fridge!).

Very easy to use- just dial the button to the load of your choice! The only problem I have is it becomes unbalanced sometimes on a heavy load. :( And it is also energy efficient and lets you know when it needs cleaning.

Maytag top loader washer will not complete cycles. Washer is only fourteen months old. Repairman says parts will cost four hundred and seventy four dollars - almost what I paid for the washer.

Went from an old simple Maytag to newer model, but still somewhat basic compared to others. However still getting used to the water saver feature in that getting in the right amount of detergent as not to have it set on my clothes and having to put through another rinse cycle and a more slimmer agitator. But do like the Maytag brand.

Havent even used the range yet and the paint is peeling off of the top. I have had the repair guy out. The new top piece of the range arrived with peeling paint also. I put in a claim to have the range replaced and was told they would contact me in 24 to 48 hours. That never happened and so I called again. They said that they would call and, of course, it didnt happen. I paid $1,300 for a stove that looks horrible with the paint is peeling off of it. What kind of ** is Sears selling? Maytag is owned by Whirlpool and nobody wants to make this right.

Bought washer in 2010 from Sears. Told me the washer had a sensor to measure how much water it needs. Was told by service guy that was a blatant misrepresentation by the sales person. It only fills up with 8 of water. When I wash my white towels with normal dirt (dog paws), with HE detergent and bleach on various cycles, my towels come out tie-dyed with dirt. Totally dislike this machine.

We are on our 2nd Bravos XL. The first washer lasted 6 years and there was a part going out that kept making it stop in the process. Basically the repair guy said it will just go out one day so it was up to us to repair or replace the machine. The machine didn’t have an agitator and we had been having issues with white residue on the clothes for a long time but thought it was related to the other part. So we bought a new one, with an agitator. It was the new model. We’ve had it around 6 months and we have lots of issues with the white residue. The only success we have with not getting white residue on darks is using deep fill and very little detergent. We use powder because the liquid makes dark spots on our dark clothes. So either way, there’s a problem. So we are using a lot of water when it’s supposed to be water saving. And we are using much less detergent that the company says. I think it’s the machine that has problems. I’ve read a long thread on Facebook and it appears that Maytag tells you to use Affresh regularly. It also says to follow their instructions. But everyone seems to follow instructions but Maytag takes no responsibility for their product. Makes me sad because Maytag was the best on the market at one time and we will never buy again. Our dryer works fine but the washer sucks. And that was a lot of money that I paid. I hope that Maytag decides to make it right and help their “customers” enjoy their products once again.

Bought a Maytag Dishwasher, model MDB89449SAM1 a little over two years ago and had nothing but trouble with it. Had Repairman out twice before but today he said we would be better off buying a new one! What a piece of JUNK and truly a waste of money! Would not recommend buying any MAYTAG products. They used to be a quality brand but no more.

I bought a Maytag washer in June and its the worst washer I have ever had. It has been 15 yrs since I had to buy a washer. My last washer was a Kenmore which was great. The Maytag does not have a water control knob. It has auto sensing which is crazy. I know how much water I need to wash my clothes. The water sensing barely puts water over the top of the clothes which is not what I need. My husband works in the oil field and gets oily and dirty. The next issue is the agitator that agitates the clothes. This one is a joke. The agitator starts agitating the clothes before the water is over the clothes and then when it needs to agitate it does a poor job. I am so unhappy with my machine that I am getting rid of it and looking for an old type washer. Evidently you made this washer for white collar people who do not get dirty. This is definitely not a washer for people who have dirty laundry. I am so disappointed with Maytag. I thought this was a good brand.

Model MDB7749AWM2. Paid over $700.00. Figure I would get a good dishwasher so it would last and clean dishes. I was wrong. I replaced all new appliances for kitchen in house we had purchase 3 years ago. I replaced door switch 4 times, front door panel where screws go in broke off. Salesman at Lowe’s said Maytag was a good dishwasher. It is a stainless front and stainless inside. I have had cheaper models and never had problems with.

After 30 months of light use.... two adults in the house, the top of the machine at the ports that allow adding fabric softener and bleach have rusted in a severe way. The machine is rusting away and Maytag customer service will say nothing except, it is out of warranty. I am very sad that I purchased a $719 washer that is falling apart with scant use.... Maytag no longer stands behind the product and I will never buy another one of their appliances again!

After reading all the reviews I realize this is a wide spread complaint. After 2 1/2 years the control panel on my Maytag Dishwasher will not work. You press the keys and hope for the best. I am thinking of going to the media with my complaint. Maybe we will all get some sort of refund or upgrade.