I bought a Maytag commercial washer - it was pricey but I loved the fact that it had dial knobs and only one feature was electronic as I find the electronics to be what fails the most. It holds a lot of clothes and gets them really clean. I absolutely love it!!

After seeing all the bad reviews about Maytag I decided to write my review, we purchased a Maytag washer and dryer 1990 when moving into our new home, and we still have the same set. Now it does not have a motherboard which I feel today is the major problem with most appliances. Get away from the motherboards. Turn the machine on and off when its supposed to, or let it run its Cycles. Dont overfill, because this causes wearing motor parts. The dryer belt wore out on the dryer but that was an easy replacement. Im a woman of 64 and get it myself. Maytag I hope that you get back to the plain ol simple washer and dryer because mine is probably going to wear out which I hope not but I would so love to get the same set I got now.

I just finished paying off my Maytag Bravos series washer and dryer, and now they are failing! The washer isnt getting dirt out and the dryer power button broke. And its not like I can use some pliers to get the switch to work, its like the part that controls the power just dropped out of existence, leaving me with a knob in my hand that connects to nothing! Of course, the limited warranty only covers the drums, not the little dinky parts that break more easily. I had inherited a set of Maytags and they were well over 20 years old (possibly 30) and they both were powerhouses. But this is terrible! I feel super disappointed that Im going to have to buy a new set after only owning these for 18 months. I know I WONT be buying Maytag ever again, though!

Purchased a Maytag MBF2256HEW bottom freezer in 2005. About fours ago, I had to replace the control board to the tune of $140.00. Today the fridge quit working and this time it appears to be the compressor, so tomorrow we will be shopping for a new unit. It will not be a Maytag.

Faulty Maytag Bravos electronic dryer model MEDB400VQ0 - I purchased a new Maytag Bravos washer and dryer in Feb 2011. About 3 weeks ago, I noticed the dryer not drying my clothes. They were hot, but not dry, leaving them hot and steamy. There was also wet lint that kept accumulating inside of the dryer. I took the back off of the dryer to see if there was an obvious problem and I found the blower belt and large bolt that holds one end of the belt to be off and laying on the bottom of the dryer. I have also looked online and did a search on this make and model and the issue I was having, it brought numerous people having the same problem on multiple internet forum sites. Apparently, there is also a service bulletin on this exact issue, but according to the Maytag customer service department, no recall. Therefore, I am out of luck as far as getting any kind of repair (unless I pay for it) because I am out of warranty by 3 weeks. I purchased the Maytag brand thinking this was going to be the best and will last me a very long time. Unfortunately, I was wrong. It only lasted me one year without breaking down and the customer service department is horrible. You can tell they definitely dont stand by their name, the Maytag name is a thing of the past. I will never recommend this brand to anyone else for purchase and I regret having swayed my mother to purchase the very same set I did. This has been an awful experience and I am wishing I had chosen a different brand. Maytag leaves me angry and very much dissatisfied.

You get what you pay for, you can go cheaper with no frills and watch how clothes wash, also run afresh through the washer as recommended. Also use the correct amount of detergent. Maytag isnt as good as it once was but it is the top of Whirlpools line of companies.

A contractor purchased the Maytag MDB7609AWW2 dishwasher about two years ago. Sometimes it will start a load, but most times it will not. The light for high temp, heated dry and sanitize work, but the heavy, normal, light indicators will not light up. Im faced with either replacing the control board or control electronics. I was told Maytag is a quality product. I have not abused the product. The last dishwasher that I had lasted 10 years. I only purchased this one because of a remodel. I will most likely replace the control board since thats the defective part. It doesnt give me a good feeling about replacing the part since it’s obviously a defective part. I will consult Consumer Reports before purchasing another dishwasher.

All I can say is what a mistake. Had a front loader that always smelled and had mold around rubber gasket in door. So, wanted a top loader this time after old GE died. Unbelievable, not enough water to clean clothing. Clothing comes out with some dry spots. And the worse thing is washing black items, tiny particles on black pants, shirts, etc. Think is lint not soap but not sure. You have to rub all over the clothing to try and remove. This washer is 8 months old and I have cleaned it with baking soda and vinegar mixture thinking this would help, it doesnt. The spin cycle sounds like a rocket ship taking off. Lots of banging noises during operation also. I have invested a lot of money thinking Maytag is rated high. It is a pretty grey color with glass top. Well I was fooled, not only the saying looks arent everything for people but its true for washing machines. I have gotten multiple mail from co. wanting me to get extended warranty. Think I will, usually dont, cause I think it wont be reliable. Wish I had my washer from the 70s and 80s. Plain old wringer that got things clean. Just put black pants in dryer on very low heat taken out damp cause I dont dry a lot of my clothing. This seems to have helped to remove stains (soap)/ lint. but, talk about wrinkles, oh boy, this machine has that spin cycle going 100 miles a minute. And if you pick a lower spin speed things come out wet. I actually can say I hate this Maytag Bravo. Things dont come out clean, wrinkles beyond control, very loud. Please folks check out your sites on the internet before buying Maytag.

In 2016 I purchased a matching Maytag washer and dryer. The reason why I purchased it because I was in a house and I no longer had a washer and dryer and I refuse to go to a laundry mat at the city to go to Nebraska Furniture Mart and it was a number of different washer and dryer combinations available. I had previously own a Samsung matching washer and dryer and it worked fine, my Maytag has dame of the same features and works great.

I bought this dishwasher from Sears on Tuesday July 15, 2014. It was delivered on Friday July 18, 2014. On Friday July 25, 2014 two plastic clips that hold the top rack on broke, and one whole side of the top rack fell down. I called the 1-800 # in the book. Then I called the repairman they recommended. He came out on the Monday July 28, 2014. By the time he got here, the clip on the other side broke. Now the rack was hanging by one plastic clip. While waiting for these parts, the last clip broke and the rack was completely detached. So he received the parts on Friday Aug. 1, 2014. When he arrived, lo and behold, they sent the wrong parts. He had the side tracks that hold the rack, not the cheap plastic clips that attach it to the racks. So I have had my new dishwasher 14 days, and have been able to use it a total of 4 times before it failed. I am now awaiting the new parts. The parts that broke are made from a cheap thin plastic, and this is expected to hold up the entire top rack and the dishes its holding.

I purchased a dishwasher model #MDB4709PAM from home Depot in March 2014. There is something wrong with the electrical and it is shocking people if you touch it. Just so were clear.. MY DISHWASHER IS ELECTROCUTING PEOPLE... Called Maytag repair because hey its only five months old. Cant send anyone out for three weeks.... three. Took an hour on the phone because I had to talk to four departments. Kept asking if anyone had been hurt seriously or property damage, so they made sure their butts were covered, sigh..... Should have bought the LG.

Internet stated refrigerators should last a minimum of 13 yrs and up. Mine is less than 5 yrs. old, a Maytag 25 cu. ft. French Door Bottom Mount Ref. with freezer on the bottom (MFF2558VEW). Had to replace upper gasket in less than 1 yr. of purchase and needs another now (not affecting the sealing aspect on doors, more aesthetic on upper door thin flap that tears easily).Drain plug & configuration for drain was a known manufacturers defect, but cost me money to replace as 3 yr. extended warranty expired. Lower gasket had to be replaced in yr. 4 of ownership, bottom of freezer was producing a sheet of ice that needed removal every week. Normal settings is #3 for both top and bottom, worked fine for 4 yrs at this setting.Last month irregular cooling started to occur- top down to 52 degrees and bottom freezer below -20 degrees - ice cream hard as rock, have to defrost each time in microwave. Maytag repairman said could find nothing wrong, but try emptying entire contents and unplug for 24 hrs. I could hear pieces of ice melting and dropping throughout the evening. Next morning towels I had put around frig were saturated with water. Restarted frig after 24 hrs. and was working fine for 5 wks.This week same exact problem returned so I did the same thing only this time I had to go out and buy a small chest freezer as I had a full one in my Maytag and no place to put frozen food. It is nearing 24 hrs. and no water has appeared on the floor nor did I hear any ice melting and dropping - so dont know what to do. Will call repair man again and see what he suggests. As soon as I can afford another $1400 frig (this was on sale for $1,002 after discounts, but I will buy a less expensive one this time) I will purchase another brand with NO French doors and no bottom freezer. I loved my frig the first 3 yrs. under warranty, but now causing me too much physical problems having to empty and restock frig for repairs. I have a Tappan Frigidaire in the garage that is from 1998 - I bought from a neighbor who was moving and it has been working fine for 16 yrs. with no repairs. They dont make them like they used to!

Bought this washer and dryer 3 1/2 years ago mainly because of Maytag name and reputation. They were very expensive to purchase. The washer is a piece of junk 3 1/2 years old used for my wife and I and leaks oil all over the floor. Called repair man to come and look at it, wasnt here 5 minutes said transmission is shot. Cost over $400 to have it repaired. We are junking it and that will be the last Maytag product I ever own.

I bought a brand new Maytag bottom freezer fridge in May 2005. The first thing to go was the timing switch. I lost all contents of the fridge and freezer. The next to go was the compressor. Again, all the contents of the fridge and freezer were destroyed. This was after the 5 year warranty was complete. The cosat of repairs is around $800.00, which is the cost of a new fridge. I emailed someone from customer service, who replied how happy they are to hear from me, and how I can call anytime. I called customer service, and spoke to a supervisor. The fridge was built in the USA, but cannot tell me where the parts are from. No one seems to get, that I am disgusted that an appliance would last only as long as the warranty lasts. Oh, and the repairs are only covered for 90 days. My parents have a 62 year old RCA chest freezer that is still going strong. The lesson is, dont get rid of your old appliances. They may use a lot of energy, but they last. I will never buy from Maytag, ever again.

We purchased our Maytag Bravos just under two years ago. Over the past month or so, we noticed the spin cycle was getting louder and louder. Today we had the service man come out. He informed us that our 2-year-old machine will require new bearings and a new basket, which equates to over $700 in repairs. The repairman said he has seen more and more of this with these high efficiency washers. He suggested that anyone buying these new washers be sure to buy the extended warranty.I for one am completely disappointed that one can spend that much money for a washer with a two-year shelf life. I personally think this is planned obsolescence created by the manufacturers. The serviceman also said the LG versions of these washers have a large increase in electronic problems. Be warned, we have very few choices these days so buyers beware.

My original GE dishwasher that came with our house finally crapped out after about 8 years of use in 2007. Bought a Maytag from Home Depot for around $400. Dont remember the model number. It worked okay but then in the middle of 2010 we got a letter in the mail saying our machine was being recalled because the heating element might catch fire (!!!). The recall gave us the option of getting it fixed or getting a $150 rebate. We chose the rebate option so we trashed this dishwasher and went back to Home Depot to buy another one.We found a very nice Maytag with the stainless steel tub and the racks with the lifetime warranty against corrosion (which was good because our previous Maytag had started to leave rust on our dishes because the plastic on the tips of the rack tines was starting to come off), model #MDBA979AWB1, serial #FY2501885. The one we found was a no-box display model but it had all the accessories with it and still had the factory warranty. We got it for just over $300 and with our rebate applied we were out the door for under $200 including tax. I installed it myself and didnt have any issues for quite some time. My wife and I were both very happy with how clean the dishes got!Now, last night the dishwasher wouldnt start. I checked it out this morning, made sure it had power and was able to get some lights on the control panel to light up but still couldnt get it to start. Looks like Ive been victimized by the control board as most of these complaints have said. I guess I should consider us lucky since ours seems to have lasted longer than the average 18 months to 2 years. Will be contacting Maytag and Home Depot to see what they can do but after reading all these negative reviews Im not hopeful.

I was repairing this Maytag Maxima washer and was almost electrocuted. I simply grabbed the wrong screws which were too long for the door switch, one screw went through into the open/close switch and contacted voltage, thus causing a direct short to the chassis and me. It also damaged my control board (the most expensive one in the industry), now Im out an extra $220 because Whirlpool made an engineering error. A screw should not be located so close (millimeters) to a voltage source where a simple mindless mistake could cause electrocution and possibly death. As for the washers operation, the drain pump failed after just two years, it sometimes leaks water out the front because debris gets into the boot drain back holes. It smells like mildew even though we leave the door open, my clothes stink, Affresh is costly and really doesnt help much. It does a decent job of cleaning, not as good as the old top loaders but it saves water. I think next tax return time this machine goes up for sale and we get a better machine.

Maytag washing machine Model # MHWE500VW - 2 control boards only last 4 years. I paid top dollar, $1229.00 to be exact and the parts and labor are $659.00 with no guarantee that there wont be further problems. Technician told me that this is typical of Maytag products. Contacted Maytag and they told me to take a hike and have a nice day. I will attempt to get some help from the place of purchase, Hamai Appliance, Maui, Hawaii.

I am in my 24th year of using my Maytag washer and dryer. The set was purchased in 1996, so it has been well worth the money. At this time, it does not spin out as well as it used to, but I just fluff the load and spin it again and then it is ready for the dryer. I have been very pleased with the set and have never had to have a repairman work on them. Cant ask for more than that!

Maytag French door model is four years old. Water accumulates on the freezer floor in small puddles. As I read other comments, this seems quite often the case. I should probably pull out the refrigerator to see if I have water leakage on my floor. From reading other reviews, it appears that Maytag does not stand behind the product. Am I forced to do the repairs myself, or am I forced to find a repair person and hope their fix eliminates the problem? Any advice would be helpful.

Dont buy their washers. Plain and simple. Will never ever buy Maytag again. This washing machine is garbage and I paid a lot of money for it. 3 months out and it had to have the entire circuit board replaced. I was assured that this was the issue. It has never cleaned our clothing, in fact, they come out twice as dirty and with soap. Weve used the Affresh, weve put as little as 1 tablespoon of detergent, weve triple washed several loads and still ended up having to wash them by hand in the tub. Changing the circuit board did nothing. Weve tried setting it to max fill (which it does) and everything still comes out the same. Its not the water, its not the water hook ups (previous washer worked great but was old, should have kept it). This is the worse product that Ive spent almost a thousand dollars on. Its a paperweight. On top of this, it twists your clothes into a mass. I expect companies to be honest about their products and provide what I paid for. How many times does this washer have to be fixed before you will call it a bad design? Im having to literally do all my laundry by hand for the last 8 months. I want my money back so I can buy a good quality product that works. I could have bought a $300.00 washer that would have done better then this. You want more proof, go read their Facebook replies to all their posts. Its all complaints about their washing machines. It would be nice for once to see a company fess up and say they made a design error. But that wont happen. Their money is more important.

Purchased a Maytag Bravo. One of the worse purchases weve ever made. First the much of the clothes does not get submerged. 2nd the clothes comes out extremely wrinkled. Called the Maytag people and they explained that Im putting too much clothing in the washer. I explained Im only filling the washer half way. They explained it should be filled only a quarter of the way. What??? Do not purchase this machine.

wW have had this Maytag gas range for twenty years. It has performed well for that length of time (maybe longer). During that period I replaced one burner. Only complaint is that the oven does not heat as quickly as I believe it should.

Maytag Centennial Commercial washer - We purchased this washer approx 4 years ago and have never been satisfied with the job it does. Most loads require a second rinse cycle and then perhaps not a good job on the clothes. We have had it repaired twice as it makes a god awful noise and does not do a wash cycle. I believe the repairman has replaced plastic pulleys both times and now it needs the repair job done again. High efficiency has led to high disappointment. We will be looking at getting an older style agitator model as we know they work! Maytag will have to pay us to buy anymore of their products, not impressed at all.

Bought a Maytag fridge model MFI2569YEM0 a few years ago. From the get-go, the ice machine would spit out ice hither and thither, mostly not into the cup or mug. Even when I held the cup up high into the dispenser orifice, I noticed it still spit out ice seconds after I released the cup, so ice cubes would spill onto the floor. Secondly, the vertical doors do not close well, and I must manually push them closed, especially the left door due to the poor design. (I noticed my neighbors more updated fridge has a better closing door. Forgot what brand, though.) Theres also rust forming on the front of the stainless steel fridge panel. It has penetrated through so I am unable to remove it.Lastly, this past week I walked into the kitchen stepping in a pool of water in front of the fridge. There was a sheet of ice accumulated on the bottom of the freezer. After some research, its likely the nipple in the back of the fridge that plugged up. I have yet to fix the problem, but so far, Maytag gets an F- in quality, and I will NEVER, EVER purchase any of their appliances again. I remember my parents washer dryer lasting 30+ years. Maytag, what happened???!!!

I asked a simple question online to see the location of the lint trap on my washer, I had read my manual and could find nothing about the lint trap, and to get a simple answer as to location, they wanted to be paid $30.00, I dont want them to come and show me just a simple answer as to where I could find it. It should be in the owners manual but it isnt

Maytag Dryer- Bravos XL - Waiting for my third service call since purchasing my dryer less than 2 months ago. After 2 service calls the repairman found a piece of the mold that should have been removed at the factory causing problems. Now, my dryer made a weird noise, sparks flew and it no longer works. After calling the seller and the manufacturer requesting a replacement, they feel it should be repaired (again).

I have an HE Maytag Bravos X washer and it cleans very well. But compared to my previous washer, with an agitator, I like the old one better and the clothes came out of the washer far less wrinkled. I would not buy another HE machine, given the choice.

I purchased a Maytag Bravos Quiet Series 400 in 2010 and it is now leaking like crazy and sounds like the bearings are going or gone in it. I researched washing machines for over a month before purchasing, and it seemed like this would be the machine for our active family. So much for research. It washes clothes okay, but is a bit rough on them. I found that it has ripped some of my more delicate items. When I contacted Maytag, they sent me an email with contact information to purchase a maintenance contract for $395 which would cover the machine for only 1 year. My husband is very mechanical and took the washer apart thinking the seal/gasket may have come off. He cleaned up the seal and the area around it, and put the seal back on. It did not help. He also noticed that the drive shaft to the motor was beginning to RUST! This machine is only 2 1/2 years old! So, if you are noticing that your whites are getting orange spots on them, this is probably happening to your washer, as well. Maytag should step up to the plate and recall this machine.

We updated our 25 years old dishwasher, which ironically still worked, to a Maytag we bought at a BrandsMart in GA in November 2010. Sixteen months later, the unit just died. The panel would light up, but would not run. We contacted Maytag and were assigned a repairman (The Appliance Guy) who could not come to fix the dishwasher until 5 days later. Once he finally showed up, I was informed by him that the control panel for the dishwasher had two shorts in it and it would be cheaper for me to just buy a new dishwasher because the repair to this one would be $344.44. When I contacted the customer service for Maytag, they offered to let me pay for the repairs and then they would give me a six month service warranty for free. Does that make sense to anyone? I could buy a totally different brand, brand-spanking-new and have a twelve month warranty with a better product. I asked to speak with Cheris boss and got to speak with Aaron, who offered me the same spiel. Heavily scripted, I apologize that you are dissatisfied, but all we can do is give you the service warranty for six months after you pay for the repair. I asked him if he was reading a script and he replied no. Now I know that he had probably repeated these same words twenty times a day. Heres a thought, Maytag claims to be a green company, using less electricity and water, and saving the customers money and yet they are filling up all the landfills with these appliances that are not even five years old. How is that being a green company?You know how when you buy a nice new button-up shirt? The makers of that good quality shirt go ahead and sew an extra button on the inside bottom part of the shirt because they know that theres a chance youll lose a button. Well, Im thinking that Maytag should just start shipping a couple extra control panels in every box of Maytag dishwashers. Crazy idea, right? Okay, so an easier and cheaper way for Maytag to correct the problem is to stop making dishwashers. Go back to the drawing board, make the engineer who designed the control panel wash everyones dishes (as punishment and he can get help from the customer service people because theyre really doing nothing), start building the old design dishwasher that has the old switch and dial, and start respecting their customers. There, problems solved!

In July 2012 I purchased a Maytag BTM standard door refrigerator from Home Depot. Approx. 2 weeks from the 1 yr. Standard warranty July 2013, my refrigerator started cycling like every 20 minutes and loud popping noises started occurring. 1st service tech would only stay 15 minutes & did not want to stick around to hear the noise. Ran the standard tests and said everything was fine. That was around Aug. 2013. So I put up with it for a few more months and finally the popping noise was getting louder. 2nd service guy (Jan. 24, 2014) got to hear my video recording of the refrigerator cycling and loud popping noise. He replaced a bad dul part (Note: they all wanted to blame it on our ice maker that we never ever hooked up). Oops...wrong diagnosis. Whatever he replaced stopped the constant cycling pattern but now the popping noise is getting even louder like a shotgun going off. 3rd repair guy (Feb. 20, 2014) tells us that is normal and recycle product material is not that good nowadays?? I pay a $1000.00 for a noisy refrigerator and they say it is a normal sound. I dont think so. The refrigerator is now popping so hard that the right side of my refrigerator that faces the open is now buckling due to the compression of the heating and cooling which is causing the loud popping noise. If you rub your hand down the side of refrigerator you can feel the waves forming on the side of the refrigerator. Trying to get a Maytag rep out here. Something needs to be done about the production of these bad appliances.

Discovered that thousands of others are having problems with the control panel on their dishwasher. Mine is Model # MDB7749SBM2. Looks as if I should just junk this horrible product and buy a new one (another brand, of course). My biggest concern is that I purchased other Maytag products along with this dishwasher, ie, a refrigerator-freezer, a built-in stove top/oven and a microwave. I have had a service call on the fridge (water line), the oven (gas) will indicate a set temperature (400 degrees for example) sometimes it will only be abt 200 degrees via a portable thermometer... Sometimes it doesnt ignite at all (have to reset it 3 or 4 times, the microwave has issues with the digital readouts, and on and on and on.I have only had these appliances about two years (after warranty expired) when each unit started exhibiting problems. I paid $175 for the fridge repair and am now considering biting the bullet & replacing everything as MAYTAG/WHIRLPOOL apparently isnt going to take responsibility for any defect on ANY OF THEIR PRODUCTS! Im 75 years of age, retired and cannot afford the replacement route but it looks like I dont have a choice unless someone has a better suggestion. I dont have the skills or energy to attempt the repairs myself.

This product was purchased in March. In September, the agitator broke off. Thats a new one on me with a washer. Every other one Ive bought tended to last 10 years or so, then something like a motor wore out. It was an obvious design flaw on a topheavy agitator held on by a flimsy plastic sleeve. To make matters worse, their warranty service seems mostly geared to selling extended warranties, necessitated by the poor quality and bad design of their products. So, for a mere $182, I can have it covered for the next six or seven times the agitator breaks. No thanks, Ill figure out how to fix it myself when its no longer under warranty, or just cut my losses by buying another machine, and never another Maytag or Whirlpool product. I had a similar experience with a Whirlpool refrigerator purchased in April 2017, which had a defective module that went fortunately just before it was out of warranty.

I purchased this machine less than 1 month ago. Have had tech here twice - he cant find anything wrong with machine. As for large capacity it will hold a lot of clothing, but will not clean them. I have had to put less than a 1/4 of tub full of clothing (about 15 small items). Use high water level, extra rinse, then rinse and spin again to get the 2 tablespoons of HE soap off my clothing. Takes over 2.5 hours to wash about 15 items. I have called Maytag and they will not back their product. I purchased at Home Depot and they said they have to do what Maytag says. Sending another tech out in 2 more weeks. Takes more water, more electricity, and more time to wash clothes than ever before.

Model MDB7749AWM2. Paid over $700.00. Figure I would get a good dishwasher so it would last and clean dishes. I was wrong. I replaced all new appliances for kitchen in house we had purchase 3 years ago. I replaced door switch 4 times, front door panel where screws go in broke off. Salesman at Lowe’s said Maytag was a good dishwasher. It is a stainless front and stainless inside. I have had cheaper models and never had problems with.

Does not wash. Only very small loads get washed even though it claims to wash bedding. Some clothes NEVER get wet. Many times the clothes have to be rearranged and re-washed AND extra rinse. Cycles are over an hour each (then multiply x2!!). Maytag service has been called MULTIPLE times. They replaced the touch pad then the computer board. Both times saying the machine works “according to design/specs”. This is a Very poor design. Maytag should recall this inferior machine as it does not perform the job it is being sold for.

The Maytag Bravos washing machine may well be the worst appliance available for purchase. Sure it is a high efficiency machine that saves on water -- the clothes are often still dry when the complete cycle is finished. Many times there is still soap residue on the clothes. Forget cleaning anything with any amount of dirt on it because it seems as though items are even more filthy after washing them. I have tried everything the company advised and still my clothes are not clean. My advice... please do not purchase this machine. You would be better off taking your clothes to a river and beating them on a rock. #wearingdirtyclothesforever

Maytag washer manufacture changes are not worth a dime. I suspect EPA made the changes, and engineering was made by someone that has never washed a load of clothes in the entire life. There is no agitator and/or supposedly made to conserve water. Well, it saves water alright with each load. There will be a 2 foot circle in the middle of a bed sheet that doesnt get wet; the same with a sweaters. I have checked with different stores and all made the same. And heaven forbid if you dropped a sock and wanted to add it to the load with the mate. The lid locks. I am both angry and dissatisfied and will tell this same story to anyone wanting to purchase a washing machine.

Ive read a few reviews and would have to agree. This is the worse washer I have ever purchased. I agree clothes go in dirty and come out dirty. I have to hand wash clothes to get them clean and wont even mention how long it takes a white t shirt to start looking like it was placed in mud vs being placed in a washer. Called Maytag and they said I was loading it wrong even though I was loading it as suggested by the manual. Then they suggested it needed service. I think not after reading these reviews.The irony is that I had called for service on a front loader due to prolonged washing cycles, the repairman was as useful as this MayTag washer. Come to find out I replaced a perfectly functioning washer, intake screen on cold water needed to be cleaned, for this piece of useless metal. I guess since reading that Maytag doesnt value its customers by offering some type of consideration I will replace this piece of crap. Please dont buy the Bravo series. You will be sorry and you will never have whites white again.

I too had to replace the control panel on my Maytag dishwasher which I purchased in 2007. I was told by my repairman to contact Maytag to see if they would do anything for me. When I called Maytag, I asked them if there were any issues with the control panels as I had heard there have been multiple issues with them needing to be replaced. I was told they had no record of any complaints and offered to sell me an extended warranty for $269, but there was nothing else they could do for me. I ultimately had my repairman order the part and it was replaced. My repairman did say Maytag did upgrade the panel because of all the issues they were having with the panel. Hopefully, they have fixed the problem and it will not have to be replaced again. But if it does, I will not replace it again. I will look into a new dishwasher and definitely not a Maytag. Yes, I would be interested in joining a class action suit.

This so called high efficiency washing machine, and others like it are absolutely awful. They do not properly clean clothes. I frequently have to put loads of clothes through two or even three times in order to get things cleaned properly which our old washer did easily in one wash. That is the exact opposite of efficient. It is so bad that it actually borders on being a genuine scam. Do not buy! Huge waste of money.

I purchased this gas range from Home Depot in 2011. From the beginning I had problems with the cooking racks slipping off the oven wall. In some instances hot liquids poured on the oven floor. I had bought a service contract on this product and when I asked that this be repaired I was told that it was not covered as it was a design flaw. The condition has slowly worsened and now I cannot cook anything in the oven for fear of the racks falling down. This is a safety feature and the oven should be replaced my Maytag.

During 2018 we purchased Maytag Bravos top loader to replace antique KitchenAid. Very dissatisfied at first, but luckily found the settings that makes my machine work very well on every cycle. First add 1/2 gallon of water to empty tub. Add detergent. Set controls at: Soil Level-Heavy; Wash temp - Warm; Main dial - Bulky Sheets; Extra Rinse - ON; Fabric Softner - OFF. Can now load full tub of clothes and more detergent if desired. Press start button and water covers it entirely. It works so well now, that I went from I hate it to I love it. Been going for two perfect months with no issues. Weird but true. Hope this helps you.

My Maytag refrigerator (bottom freezer) is about four years old now. Since the first year, it has been freezing up. The refrigerator gets warm and the freezer stays cold. Two repairmen have looked at it, replaced the electric panel and the thermostat - neither repair fixed the problem. If you completely defrost it, it will start working again. For about three years, it would work for a few months, but now it will only run for about two weeks before freezing up again. I called Maytag when this first started happening and again recently. They say they have never heard of anyone having this problem and they are sorry. The woman said she would put my complaint in my file. I certainly would recommend that people avoid Maytag refrigerators.

We purchased a Maytag refrigerator in 2009. The freezer is on the bottom. In the last 3 months weve had to defrost this frost-free refrigerator. The freezer frosts and the refrigerator went into the danger level for foods. A technician said there is a tube from the freezer to the refrigerator that gets blocked with ice and your food is spoiled in no time. I wish I would have read this website before I purchased a Maytag. Hopefully, this will help someone else. I thought that Maytag was a quality name. That was the good ole days and now Im living in the good ole days defrosting a frost-free refrigerator. Beware!

Maytag Gemini - This is a double oven which I purchased in 2010. 2 days ago Apr 13, 2015, the outside glass in the bottom oven simply exploded. The oven was in use at the time. It blew the side brackets off and glass was spread into my dining room as well as a mess in the kitchen. Maytag was supposed to send repairman today. Have waited all day and finally called repair company. They knew nothing of the repair and supposedly will contact Maytag and call me tomorrow. We will see. In the meantime has anyone else had this problem?

I bought a Maytag washer and dryer unit from Lowes 3 years ago. The idler pulley failed causing a squealing noise every time we turned it on. It had to be replaced along with a new belt. The washer failed to work shortly after that. It had error codes that Maytag could not give me information about. These were both higher grade commercial units. We hoped they would last longer than 3 years without having major repairs. We also have had to install two lid switches for the washer in that same time span. Quality has been very poor and customer service has been worse. I will never buy another one of their products again.

Maytag Dishwashers work great. It cleans well and appearance is very good. I have always trusted Maytag appliances. Its quiet running and also energy saver. If I had to replace I would stay with Maytag.

After 1.5 years, our Maytag bottom freezer ref has started leaking water on the floor. There is a sheet of ice on the bottom of the freezer, and ice in the slots on the back wall. This sounds like a frozen moisture drain. This seems to be a common problem. There should be a recall.

I have a bearing going out. The Bravo washer makes a terrible noise. Now, they tell me I need a new tub/bearing. This repair will cost me more than $250.00 plus service calls. This is the second repair that I have had on this machine. It is only 4 years old. I use it twice a week. I will not recommend Maytag to anyone and I will never buy another one. They should check the internet for complaints and realize that there is a problem.

Horrible washing machine. Cannot get clothes clean. It simply does not supply enough water to wash. Have tried everything. I want my money back. How do you start a class action lawsuit. Thousands of people are dissatisfied also.

Almost 2 years ago this dishwasher wouldnt drain. Fixed that $300. Then just over a year ago control panel had to be replaced. Now control panel was bad again, had to rest circuit to get it to start. I see this is a common problem. Only 2 of us in the house and the dishwasher gets used only 2-3 times a week since we purchased brand new in December 2011. Ordered the new control panel and just went to replace it, guess what. This appliance could have burnt our house down. The wiring in the door that plugs into the control panel is burnt! Not at the panel at all but a good 8 down the wiring harness. Both harnesses as well. Scared me half to death! To think it could have killed us at night, when we usually run this appliance. Definitely calling Maytag now. I do have pictures as well.

I purchased a new Maytag fridge apx 8 months ago (model# MFF2258VEW6). It has french doors and a bottom freezer and from day 1 it has constantly leaked water all over my kitchen floor. I started putting towels in front of it after my first slip and fall. I had the water line checked for the ice maker and it was fine. It continued leaking day after day. Then I started getting a lot of ice build up all over the drawers and on my frozen food, which became freezer burned and I only had the temp at 2. They have a warranty on it, so called the company and they brought me a loaner fridge of the same kind.. OMG this fridge is doing the same exact thing, even worse. I am disabled and fell last night again and my leg and foot is so swollen.. I really hurt myself and Im not going to let this company get away with this!! I called the company and told them and they are checking into what they can do with the refrigerator. After reading all the about the Maytag bottom fridge leaks and other problems, I refuse to get the same one again. If they do not do something, I promise I will before I get hurt again!

We received our new Maytag French door refrigerator today via delivery and got everything set up and magnets stick to the front. The last I checked magnets should not stick to stainless steel. So I called the Menards where we purchased the refrigerator almost 2 1/2 weeks ago and the store manager said there was metal liner under the stainless steel and states this on the technical specifications. And everywhere I went to look under the technical specifications NOWHERE does it state there is a metal liner underneath and even if there was the top is stainless steel regardless so why would magnets stick to it. I paid for a Maytag and basically got a cheap piece of crap Frigidaire or Whirlpool and paid extra for Maytag to stick a Maytag label on it. What a joke. If I have any other problems I will personally deliver this refrigerator to Maytag/whirlpool corporate and put it on the front step. I am VERY ANGRY!!

Purchased this oven at Lowes on 2/8/2018 for $1925. Worked good until my wife cleaned the lower oven on 11/22/2019. The next morning the oven was locked and nothing would work. We called for service and the repair bill was $194.55. I told the repairman that the oven had a 10 year warranty on it, one year on everything and the rest on the parts only. He said no, and showed me in the warranty book that it only covered two parts. Which was not the two parts he had to replace. If you purchase a oven with self-clean feature, I would recommend that you do not use it.

In a way, l feel fortunate and you will read why in a minute. l have been reading Maytag complaints specifically looking to see if what happened to me has happened to others. Apparently, it has. We purchased our Maytag range, model MER57750AB, in 2005. We too have had some repairs done under warranty. Unfortunately, we live in a day and age where technology isnt always our friend. The old appliances that were not electronically driven lasted forever; todays appliances do not. However, when something with potentially serious consequences happens that is not technology related, it rates in the who is the idiot who designed that? category. I am talking about the exploding exterior glass oven doors.Two weeks ago, the oven door handle on our range came unscrewed on one side. I continued using the appliance, planning on repairing it myself when l found the time. (I used to tinker around the garage with my dad when I was little and therefore, I have great repair skills in several areas.) Last week, I was standing in front of the stove when all of a sudden, the glass panel dropped from the door! It landed straight up on the floor and fell forward so the top edge of the glass landed on my toes (the toes that I had surgery on for six hammertoes last November and are still sore!). Needless to say, l was shocked that this happened, and even more so, I was grateful that it did not break or either of my two grandbabies were around at the time. Then, I looked at the glass and saw that it was attached to the door using only eight small pieces of double sided sticky mounting foam. I mean small! As I said before, idiot! Did they not think that the heat from the oven would eventually wear out the ability of the tape to do its job? I gave up reading after I found enough complaints about the mishaps with the glass on the oven doors to realize that there is a definite problem here. I did not see where the glass fell intact, as mine did. Therefore, I am suggesting that the exploding glass panels more than likely gave way, as mine did, and shattered when they hit the floor. Should there be a product recall for this? Absolutely! The question is how does a recall get put in motion? As others have stated, this could have been a horrible disaster had little ones been around. I pray that doesnt happen to anyone.

I purchased a refrigerator in Aug. 2012 from Home Depot. In June 2013, it broke. I contacted Maytag/Whirlpool and they had three companies come out to try and fix it over a four-week period when finally it was determined that it was unrepairable. Now I was told that we can get an exchange but now they have the incorrect delivery address and the person supposed to be handling my case has been on vacation and I left several messages. I contacted Maytag for someone else to help and cant seem to get anyone for the past 2 weeks. This has cost me money for food lost, time from work and time making calls.

I purchased a Bravo washer and dryer set about a 2 1/2 years ago and had problems from the start. The dryer control panel went out the first day. No problem, they replace the panel. The washer is a different story. The agitator went out next and the wait time to repair it - 3 WEEKS. The agitator went out again for the second time and the tech stated that it had to be replace. Wait for it. Waiting time - 1 month including parts. To make this story short the agitator will go out every 4 months and the tech stated once its been replace it will work like a new washer. Wait for it. The agitator has been going out ever since and the wait time average 3 WEEKS. Wait for it. This Maytag is trash.

Pretty much the same complaint as Ive read about the Maytag dishwasher control panel issue. I purchased ours in Nov. 2009, issues began in April 2011, and service call for $129 where the technician said it needs a replacement control panel. I spent another $130 for the part and warranty on this specific part. In December 2011, issues occurred again. I ordered a new control panel in January and was told 3-5 days, called after 10 days and was told it was on backorder and should be shipped sometime in March. Youd think the Maytag President would be embarrassed for producing a product like this that in my eyes has tarnished what was a reputable household brand. Not that it will do any good but I will mail a letter to the President. One positive, our kids are learning to wash dishes the way I did as a kid, by hand. I sure hope the new control panel we hope arrives in March fixes this problem for good.

Bought the Maytag high efficiency washing machine with the auto-sensing and deep water wash feature. It took some getting use to because of all the washing choices and different noises it makes. Auto-sensing seems to use very little water which is strange but clothes seem to come out clean. Best bet for me is like the old school way and use deep water wash and light load which is shorter and thats most efficient power wise but will use more water which is fine by me. Also bought the matching dryer and thats a 5 star review. Excellent product.

I purchased by Maytag Bravo from Lowes exactly 1 year ago when the gearbox failed. There was a loud grinding sound as the washer tried to shift from wash to spin. Reading through some on-line reviews and complaints it turns out that this is not a new problem and has been known to Maytag for some time. I specifically bought a Maytag because of their prior reputation for quality. Unfortunately, my information was out of date. It is so sad that a company would compromise such an outstanding reputation.

I purchased a Maytag side-by-side refrigerator in May 2010 to replace a 20-month-old Whirlpool fridge with a dead compressor. The now 14-month-old Maytag has a dead compressor. I have been told by the repairmen that I have come to know that the compressors used in these units are of poor quality and do not last. That must work out well for the appliance industry if consumers must replace a $1,000 + unit every year or two.To Maytags credit, I spoke to customer service and they agreed to cover the parts and labor for the repair even though it is two months past warranty. Maybe I can get another year out of this reliable appliance. I am told that all of the major brand appliances use the same compressor.

My husband and I were Maytag fans, and we purchased the fourth set of Maytag w/d in May 2019, along with an extended warranty. Four sets may seem like a lot, but my husband and I have been married for almost 30 years now. Long story short, the washer went haywire, and kept flashing LF. After searching Google for answers, my husband flipped the main breaker, then unplugged the washer overnight. It seemed like that fixed the problem, but it didnt. I called Lowes for help and got hung up on numerous times. The hang-ups were not due to my attitude or choice of words. I kept getting transferred from person to person and put on hold, then the phone would go dead. Eventually, someone actually spoke to me and gave me an 800 Maytag number to call, which resulted in more hang-ups.As before, eventually I got to speak to a real human being who took my info and said that a service tech would contact me. Well, over two weeks later, no one has contacted me. However, due to my post/review on the Maytag website, a Lowes representative did call me and offered me a full refund on the washer, but not a word was mentioned about the dryer that seems to be possessed because it turns on and off at will. My husband and I have a limited income, and we purchased the top-of-the-line Maytag w/d thinking that it would last at least ten or more years.For the money that we spent, the w/d should have at least lasted for the warranty period. As noted before, Maytag was once the Toyota of w/d. You could not purchase a better product. Now, the exact opposite is true. Buyer beware, the most expensive with all of the bells and whistles is not always the best. My husband and I have gone retro with the purchase of a new Speed Queen w/d, which will be delivered this week. Hopefully, it will live up to the reviews that I have read.

Bought a Maytag refrigerator/freezer 18 months ago. The freezer went bad. The first repair guy said it needed a new computer board which wasnt covered. Called Maytag, they wanted another repair service to look at it. He said it needed a new evaporator. We have now spent $250 to be told the repair will cost another $500. Maytag will make a goodwill gesture because we are a nonprofit business to cover the part only so we will still be out another $300. This is unacceptable for a relatively new Maytag. Obviously they can no longer be counted on to back their equipment. Very disappointing.

We were excited to finally buy a new wash set and I always wanted the Neptune ones. I had owned a Maytag for 25 years through two children and a mechanic husband. I had every confidence in the new ones and expected at least the same service. Shortly after the warranty went, the machines both started to act up. The washer would stop in the middle of the cycles. The dryer wouldnt come on or wouldnt respond to the commands. We finally contacted the local repairman whom we have used for years. He came and gave us boo-hoos about these machines. He said they were trouble and we should have never have bought them. My husband figured it was the electronics in the control panel. The repairman said the parts would cost somewhere near $500.00 to $600.00 each and proceeded to try to sell us used ones for $2,000.00. We said we would try to get the bad parts and he even gave us the stock numbers? We went online and found new ones for half the price. We bought them and put them in and they persisted in doing the same things as before. Is this a runaround or what? Who is bilking who? Another great American rip-off. What can the public do?

Same as the rest of complaints. Dryer needed a new motor 3 months after purchase. Crazy. Door magnet replaced at 5 months. Lint screen replaced. Washer electrical board replaced at 8 months. Cloths come out wrinkled, tore up with holes and I have like bleach spots on clothes that I didn’t use bleach with. Now the washer is screeching and coming UL. My husband thinks its the bearings and tub seal. Called Sears and parts alone are 185.00 not counting labor. Of course its out of warranty now. Seen comments about a class action lawsuit. I really think this product deserves one. Why should we as consumers have our hard earned money wasted on a product that doesnt meet our standards for a quality washing machine that we thought we were buying. Whos in.

We bought commercial Maytag washer & dryer Oct 20th 2020. Very expensive ones. Oct 13 2021 they stopped working so had it checked. The shifter on washer went out & dryer blower is not working really!!!! Not even a year! Been without washer & dryer for 1 month because they didn’t have availability & now have to order parts another 2 weeks!! Never buying this product again!! Don’t buy Maytag!

I seem to be just another unhappy Maytag microwave oven customer. The SE code indicates a bad/faulty/short in the keypad. It seems this is a very common issue so buyers beware! If I dont get this resolved, I will no longer buy Maytag/Whirlpool products.

Maytag Dishwasher Model MDB 7749SAM0 - Bought this dishwasher from Lowes in 2012 for my daughter and son-in-laws new home. Thought I was making a good choice with Maytag. Wrong. Same control board problem that everyone else is having. Wiring ribbon is corroded and shorted. Why is this not a re-call? I will call Maytag and Lowes and complain, but likely will get no justice. Sounds like I should just bring this machine to the dump and take my losses.

First of all how you wash a load of laundry with a cup full of water? I got this washer and dryer (XL Bravos) as a birthday gift from my husband. This is the worst washer Ive ever had. It takes forever to wash and the laundry is still dirty, it only has a cupful of water in it. Im so disappointed at Maytag for selling something like this. If anyone is doing a class act lawsuit please include me in.

Maytag Bravo washer and dryer purchased April 2011. Dryer works fine and am pleased with results. Washer does not clean simple dirt and stains off clothing. Washer never fills to a water level that covers all the clothing. Some clothing never gets submerged, thus simple stains never get water contact throughout the cycle. I now spend more money purchasing spray stain removers and using the heavy duty cycles and extra rinses, would have been better off getting a Kenmore with an agitator. The concept does not work.

Sears washing machine model # mvwx500xwo - This machine is the worst. My mother who is 87 years old smells like mold every day due to the smell that comes from this machine. Im not sure whats going on but the plumber told us there is something very wrong with this machine. Its not the hot or cold water that smells, its the machine. I am now concerned about my mothers health. Please advise if you will allow us to purchase another machine with some kind of a credit due to the serious issue this machine has.

Do not buy a Maytag dishwasher with model # MDBH969AWB1. I bought this dishwasher last Dec. 2010. I could not use it for 2 weeks, because the door would not shut. The repair man came & fixed the door. Then when I actually got to use it and after it finished running the cycle, the tub was dripping with water all over--top, sides, door, bottom. I had to dry the dishes on the top rack, and I had to leave the door open for days in order for the inside to eventually get dry. The first thing I noticed about this dishwasher when it was installed was that it was smaller than my other dishwasher. I hate the design because of the way they have made the racks plus because it is smaller--it holds less dishes than my old one did. I could actually get almost twice as many dishes in my old one than I can with this one. Do they not think of asking the consumer about what they want in a dishwasher instead of going ahead and making something that is not functional?I am so frustrated with this thing; it has brought me to tears. I just today went to Sears and looked at their Kenmore dishwasher. It is designed more like my old one than any of the other makes out today. I wish I had checked this out, before I bought this Maytag. Weve always heard how Maytag is at the top of the line with no problems, right? Dont believe it. I will never buy another one. Whoever is designing these dishwashers need to go back to 1990 and take a look at how it was designed and then go back to making them like that. I loved my older dishwasher, and I wish I had never let them take it away. I wish I had taken the money I spent on this ridiculous Maytag and had my old one fixed no matter what the cost. I made a terrible mistake.If you have an older dishwasher and it has given you good service for years, I suggest you have it fixed and keep it, because you will not like the performance of what they are selling today. It does not matter what brand you buy, they are all designed the same. Just take a look and compare them. But if you buy, please check out the Kenmore. I dont know if the performance is better, but the racks are better designed. My old dishwasher was a Hotpoint. It was the cheapest one on the market, and it gave me the most wonderful service ever. The dishes were always very clean, the heating element was fantastic, and it always dried the dishes completely. I cant believe they would make a product like they do today and sell them for what they do. The heating element in them today is not as good or strong as what they used to make. That is why the dishes wont dry properly. You get way less than what you pay for. Thinking a new dishwasher is the way to go, think again. Please, if at all possible, keep your old one and have it fixed over & over again. I hate this dishwasher. What a joke on the unsuspecting buyer.

We have owned a Maytag Commercial Centennial washer for 4 years and made the mistake of not buying an extended warranty as we thought Maytag was dependable and a reputable company and thought the manufacturers 10 year limited warranty would cover us. Washer would not spin clothes properly, started making loud noises, lid would not always unlock as time went on, and finally it broke and soaked my tile and it ran through my wall into my hall carpet. Called Maytag and was told we didnt have a 10 year limited parts warranty 6 times (we still have the book that says we do), they offered us a 1 year full warranty for $320.00. We purchased the warranty 11/04/16, Called Maytag as no one knew where the parts were and was told service plan is through AIG. AIG couldnt tell us where the parts were either and when I asked for our refund and we just buy a new washer they advised me they would have to prorate it.Now I feel held hostage. Parts finally come in and Maytag Certified repair man comes to repair machine on 11/30/16, only to be told they could not fix our washer as the screws and transmission rotted and fused to tub. Call Maytag as this should be under my warranty and everyone insists I dont have a warranty. Filed complaint 11/30/16, they sent me a survey on 12/2/16 and I filed my complaint again on the survey. No call from Maytag. Call back on 12/06/16 to be told the survey was them closing my complaint. Now they escalate my complaint and will be called in 48 hours and give me an email address to email my pictures of my warranty. Surprise no call back, so I called them again 12/08/16 and I am advised it takes 3-5 business days. Ask for supervisor and he told me even if I have warranty they will only cover the basket.I will have to pay for technician, and other parts. Still no info on my complaint and you cant talk to anyone just have to wait. I emailed Jeff Fettig CEO of Whirlpool (Whirlpool owns Maytag) as well on 12/6/16 a copy of my complaint with pictures of warranty. The bottom line is Maytag sells junk and their customer service is worse than their product. After being without a washing machine since 11/04/16 we will be buying something Whirlpool does not own which is very limited which is why they can get away with making junk.

Maytag dishwasher #MDB 9750AWQ - I am now on the fourth control panel and in less than one year, the present one is starting to fail. The third one failed in less than a year also! I have read the reports of others and apparently, this is not just my dishwasher. Maytag owes its customers a recall of this inferior machine.

Called to schedule service for letters on door to be replaced ice and water completely rubbed off until you didnt know which one you were getting. Refrigerator is less than 10 months old. Also freezer door was hung lower than refrigerator door. Was told nothing could be done. It was a cosmetic issue. Very rude customer service dept and I talked to two separate people and they were both rude and unwilling to help. I can promise you I will never buy any of their appliances again.

My dishwasher, purchased in 2013 sings the same tune as many of these complaints...stopped working correctly, turned on whenever it wanted to, etc. Thought it was the cpu...no. Called Whirlpool and they gave me the same runaround that they give everyone...more money for a temporary fix. Did some more research that led me here and discovered that the ribbon cable leading to the control panel was fried due to heat and moisture. Easy to check for yourself... looks like brown crap on the cable...if you have a meter, you can easily check it. Tried to repair it, very difficult, but I tried. NEWS?...I wrote a complaint to the Better Business B... and mentioned that this is a safety issue, which it is.Believe it or not, just received a call from the corporate office (Whirlpool) and they were interested...I actually got their attention. They said they would have someone contact me... she did today... so this is encouraging. I dont know what they are offering, but this poor design is a serious problem, and if you want to get in Whirlpools face better go through the BBB. I already have purchased a new part and am adding silicone to the cable to protect it from the heat...but Im really seeking full reimbursement because this is not going to end well. Good luck...

The lid on this washer cracked twice. It is made out of plastic and is now discontinued. The lid cracks no matter how gentle you are with it. It is just over a year old and will have been serviced twice. The lid has to be ordered and you have to wait for a week. Maytag will not offer a new machine.

We bought a heavy duty washer 1 year ago and paid a decent amount of money for it. Had it delivered and installed mid February of 2020. Worked fine until Dec when the lid cracked (which is common said the Maytag repair man), but since it wouldnt lock, we couldnt use the washer. 1 week we were told and it would be in - a month later and over a hundred dollars spent at the laundromat, the part came in. Used the washer for 1 round of laundry - 3 days later all these error codes started and our washer wouldnt work again. 2 weeks this time for the parts and another $100 at the laundromat- a month today and Im told they are on backorder.Called the place we bought it and they said to call Maytag. Call Maytag and they said that they will try to expedite the parts and could offer me a whole $75 for the inconvenience. They will not replace the washer or give me a loaner until the parts are in. 2 months w/o a washer on a 1 person income for a family of 4 and they cant do a single thing to help. If a 10 month old washer needs 3 new parts one of them being a new control panel - within the first year - this is a lemon and should be replaced. I was told they are big on customer service, but obviously Im just a little fish in the ocean and they dont care about me.

I purchased a Maytag Neptune Washer and Dryer at Home Depot for over $900. Within months, the board went out. The repairman said that they didnt even know how to fix it yet - no training. The board was out again. This time, it was not under warranty. The repair costs $779 including part and labor. There were numerous other little problems along the way that we did repair, but now, forget it.

Maytag Washer Model#MVWC465HW2, just purchased it 1/30/2019, leaves white stains on dark colored clothes. I use liquid soap. I don’t use softener nor bleach. I use OxiClean on my whites and sheet softener in the dryer. Someone please out there help, I can’t return it, it’s past 30 days. I have extended warranty but they can’t help. It’s not broken. I hear a lot of bad reviews/complaints, but no answer if it’s been solved or how to solve it. Please someone help???

We purchased a French door Maytag refrigerator model MFD2561HEB in November 2007. In August 2008, the unit stopped working suddenly. The high voltage control board was replaced under warranty, but the tech could not determine why the board failed. I called Maytag to demand a new refrigerator. The best they would do was to extend the warranty for 6 months, no charge. The unit quit twice more in September. A tech was summoned (paid service call), nothing found. It started working again. Since then, the thing has quit several times. We unplug, move all food to a second refrigerator, wait a day, plug it in, and move the food back. The useless box quit completely this week, not quite 5 years of service life. The tech said the board must be replaced again, no guarantee. We declined. I called Maytag again to demand a new replacement and escalated the complaint. They are to call back, ha! In the 5 years of poor service (and poor customer service) from Maytag, the 30-year old second refrigerator has been up to the task of preserving our food. This experience has made me vow never to do business with a Whirlpool-affiliated brand again.

I purchased my Maytag side by side Model No. MSB27C2XAM00 in August of 2013. Within a 2 Weeks the lettering was gone on the control panel for the ice and water dispenser. I contacted Maytag and they replaced it, but the next one did the same thing, and the next one! They replaced it three times and they have all done the same thing. Now they are refusing to do anything more because they say I must be using cleaner or something on the panel because I am the only one having an issue with this! I assure you I have not used any cleaner and there are only three people in my household so it doesnt even experience excessive usage! I know this problem isnt as extreme as some, but when you pay this much money for an appliance you would like to think it should last longer than this!

Purchased Maytag dishwasher July 2013, installed August 2013. Stopped working Oct 2, 2014. Called Maytag and they offered to let me buy a service pan for around $300. No thanks, stupid Im not. I also sent an email. Have not heard back but Im sure Im still out of luck. According to the California class action suit regarding the Maytag control panels, Maytag is saying there are no problems with them. Wish we all had some power to make them see otherwise. Will I ever buy a Maytag product again. No. They would be much better off keeping their customers happy rather than spending tons of money on ads trying to get new customers. Since Maytag is owned by Whirlpool, they will not get my money either.

We bought our Maytag dishwasher because of the topnotch features; such as 10 year warranty, low noise level, maximum cleaning power and it looks great. The dishes come out exceptionally clean and don’t needs to be rinsed prior to putting them in.

Bad decision, Purchased in 2013 a Bravos by Maytag. After 3 years, it sounds like a jet engine taking off. The bearing is failing, sad as Maytag advertises to be the best. In 35 years, this is our 4th washer, actually the 1st was a hand-me-down that lasted longer. Unfortunately, we thought spending more and believing that Maytag would last longer was a mistake. Cost to repair is over half of the cost, so we have elected to run to fail. Then replace the Maytag that should have lasted at least 10 years. Warning. Purchase at your own risk. DO NOT buy this machine or any by Maytag, could be the same results. Or it could be that they are manufactured under Lowes specifications. From all the complaints the Maytag repair technicians are working, not setting around as they advertise. Only blaming myself for the purchase.

My Maytag (MDBH955AWB) dishwasher (not even 6 years old) is losing its prongs that help the dishes to stand up. They are corroded at the bottom and snap right off, leaving the dishes without support and banging into each other. We are only a family of 3 so it gets moderate to minimal use. The bottom basket costs $200 to replace, a third of the cost of a brand new dishwasher. Everything else about it is fine but my dishes will be chipping away. I cant believe Maytag made the basket so poorly that it doesnt last the lifetime of the dishwasher.

I wish we would have never bought this brand and model. Within a month there was a loud banging and the serviceman came out and changed a valve out but it just got a little quieter but never went away. 2nd issue is cloths ball up when your doing bedding. Not sure if they are really clean or not. 3rd when we take the cloths out of the washer we are still seeing soap spots where they were not rinsed very well. We are using the right soap Gain but we cannot wash cloths in the bedding setting. We have to use the extra rinse setting to get all the soap out which defeats the whole savings issue of this machine. It says when you do your monthly machine cleaning it resets the water level but there never seems to be enough water in the tub. Also if your doing sheets in the washer and when the spin cycle starts you have to hold your breath to see if its going to get out of balance which it does 50% of the time so you stop and move things around. Also we cannot put a whole lot of cloths into this big drum because they dont wash correctly. Worst purchase we ever made. With all the negative reviews you would think that Maytag would come out with some fixes but I dont think they really care anymore.

Within 2 months of 1 year warranty running out, the control panel went wacky - does all kinds of weird things except work right. Called to see if there is any suggestions or work arounds and was told they would be glad to set up a service call for between $70 and $100, where they could tell me how much it would cost to fix. As with the other 100s of folks with the same problem, they basically said gee, you should have bought an extended warranty. If you have this many people with the same problem then it is Maytags problem, not the poor sucker consumer who got stuck with it. If you are considering this dishwasher, run, dont walk, as far from a Maytag or Westinghouse product as you can get. If anyone starts a class action suit against this product, please count us in!

Have had this side by side for a long time and it is great. Have not had any problems with it. Also have had an Amana which we love as well. These are side by side and are frost free and never have to clean.

I purchased a Maytag Dishwasher (MDB7749) in 2012 and one day before my 1 year warranty was up, my start button on the control panel wouldnt work. I called P.C. Richard and they sent a repairman who fixed it. This was in June of 2013. Here I am now hand washing again 1 year and 4 months after the repair. I called P.C. Richard again and was told that all brands have their weak points and because I got it on sale in the first place, I should not feel angry.Now that I am reading the reviews from 5 years ago, I realize that P.C. Richard knew this was an issue and chose not to disclose it or stop selling it. I had my G.E. for 10+ years and will go back to one. As I have no money for another new one, I will try to learn to fix this one on You Tube.

I bought a model MDB7749AWW1 Maytag dishwasher in May 2011. I thought I was getting a nice one, but no one really liked the way the racks were designed after we got it installed and began using it. My biggest complaint however is with the control panel. It failed in November 2011 and was replaced under warranty. It has now failed a second time in June 2012 (just over one year old and out of warranty). Theyve offered to pay for the parts since it is so close to one year and I pay labor. Well see how that goes. Looks like there are lots of problems with Maytag control panels.

The Maytag Commercial Technology wash machine, the one with the clear top, leaves soap residue on our clothes. We have tried different detergents, always high efficiency, using the extra rinse, using the deep fill and nothing works. We have tried cleaning with vinegar and using the clean washer cycle. We had 2 technicians look at it, one tore the machine apart, both said nothing is wrong with the machine. So, we are left to believe that we are stuck with a machine the leaves soap residue on our clothes as Maytag will do nothing for us because of the assessments of the technicians.

I owned a Maytag Bravos top loading washer for 8 years, and I loved it. It caught on fire while washing a load. Thank God I was home or it could have burned my house down. Just wanted to post this somewhere to issue a warning.

Bought Maytag Dishwasher in 2/2012. 10/2015 dishwasher stopped working. My husband tried to replace the motherboard, however, dishwasher completely done. Called Maytag and they said they would send a repair company at their expense, however, repair service called to verify appointment and told us how much it would cost us! Maytag had no intention of paying the bill even after they said they would. Called Maytag back and said the other customer service person was incorrect. Now, buying another dishwasher only after 3.5 years.

Because the design is bad, the refrigerator has to be defrosted once a month. A home filled with Maytag appliances, these are all 4 years old and ready for the trash. Dont buy Maytag, it is crap. They sell for money, not workability. The name has been trashed by Whirlpool. I am a builder and they will not ever see me recommend them, not even to a neighbor I dont like.

We bought Maytag Dishwasher on October 9, 2019. Due to the installation difficulties we were not able to install and try it right away. Lowes warranty expired in 30 days, and the dishwasher is not cleaning the dishes. Even with the hand prewash of all of them-they come out dirty. I have to clean them after. The dishwasher is very weak. We contacted Maytag and were told that they can do nothing for us, only send technician (we have to pay $160 per visit). We can not return or replace it, the quality is very poor, so we will have just to buy a new dishwasher and lose 500$ for this product.

We bought this from our local big box retailer paying $433.87 after installation, the oven, haul away and home delivery. Two years and 3 months later its a boat anchor. Display is cold and dark after stating we needed to open and close the door before it would heat. We did but it kept displaying the same message. Unplugged it, turned circuit off per Maytag customer service line, still nothing. It is no longer made and you cant get parts. It is useless. The 10 year warranty just covers the magnet and the cavity.

My husband and I purchased a Maytag stainless steel French door/freezer bottom ice making fridge from Hhgregg in Brown Deer, WI and 8 months later (now), Ive been told that my food that is spoiled, cant be replaced and my service for the fridge wont be done until next week! I have 5 kids and a husband. This has turned our world upside down. I called them and spoke to a Nicole and she said they cant do anything for us, but we can try to contact the diamond repair service at 269-927-2519 to see if they can get us in sooner. I asked for a refund for the fridge and she said no, the 10 warranty only counts for repairs... I am so angry that I didnt research Maytag before now. I gave the Whirlpool fridge to the delivery guys of Hhgregg and I had that for 18 years and it never went out on me. If anyone is reading this and is upset as well, let us get together and start a class action suit!

Maytag Bravos XL - I have always loved Maytag and never had any problems. In Feb we did some major remodeling with new flooring in our laundry room. Decided to buy a brand new washer and dryer even though our 10-year old Maytag washer and dryer worked perfectly fine. After looking at Home Depot and Lowes we first settled for a Samsung W & D but before it was delivered we shopped some more. After doing some inquiring we decided that we wanted to stick to a long trusted W & D line so we chose this washing mashing and matching dryer. From day one I decided I did not care for it. I found if I put too many clothes in that they did not come out clean. Any dark pants would come out with what looked to be soap or softener stains and would have to rewash 1 or 2 times. Now I can only put in about 4 pairs of pants to wash. I have been cleaning it once a month as the manual says to do but yesterday I noticed a terrible odor coming for the washer. I could smell it out in the hall. I did the cleaning again but still smell it. Now after searching the internet I find a video that shows the problem is mold under the drum. No amount of Affresh or bleach is going to clean something UNDER the drum. It is not my job to have to take this apart every few months and clean out mold and moldy water. Sounds like this problem has been going on for a few years and this should have been fixed long before this. I wish I had my old faithful washer and dryer back. Maybe I should have stuck to the Samsung washer and dryer.