My name is Mrs ** and I dont have a complaint. I would to tell you about our washer. It is a Maytag. It use to be my mother-in-laws. She did laundry in it for 4 grown boys and 1 girl plus her and her husband. She passed along to my husband a long time ago. And now it does laundry for 6 kids plus my husband and me. I run it 2 days a week sometimes more. The washer is between 25 and 30 years old. And works good still. Im not sure how much longer it has but we are happy with it. And soon Ill be washing for 7 kids. We have made a decision to start looking for another soon. But I wanted to share my story with you. My husband is now in his 40s if it says how long it has lasted. Thank you.

Ive had my Maytag microwave (MMV4203DS00) for a little over two years. I started getting SE error code. The control touch pad membrane is shorted out. I suspect because the design doesnt allow it to be an over-the-range even though thats the kind of microwave it is! I think the humidity from the burners shorted out the membrane. I called the company and the part would cost approximately $180 for me to fix myself. I have a really hard time believing that one part of a $200 microwave costs $180. Ridiculous. It appears this microwave is designed to fail. Customer service was rude and snarky. The company doesnt appear to stand behind their product. Maytag used to mean something. I had started to replace all my kitchen appliances - microwave, then stove. I thought Id be consistent and buy Maytag based on their reputation. I will never buy Maytag again.

The machine has left pin-sized holes in finer clothing since we first used it. I had purchased the extended warranty so they were called out to repair the issue four times during the warranty. They replaced the drum, but I still get holes. I think it is because there isnt enough water to rotate the clothing and it rubs repeatedly against the same spot on the other clothing. I have a see-through lid and you can see that the clothing just moves very slightly in the same position. I separate all clothing that has a zipper or any trim that may rub against the finer fabrics, but I am still getting pin-sized holes. We requested compensation or a new machine. They extended the warranty. We have replaced enough clothing that we are now buying a new machine. It will NOT be a Maytag.

The Bravo HE Washer was a cheap piece of garbage and I am very surprised Maytag put its name on it. It broke down exactly one year after the warranty went. It did not ever clean clothes properly and all stains remained even when you spot clean first and double rinse. Maytag basically ripped us all off and somebody should start a class action lawsuit for this thing they call a washing machine! What a joke! I wont repair it. It will just fall apart again. Im not stupid. I know this is how they pay their employees doing house calls! So now, I have to go to garage sales and look for one made in the 1970s because that is when machines were made in the USA and things were built to last, not this crud. Maytag should be ashamed. It is time for them to close its doors. Sorry but its true. They are just crooks now selling crud that falls apart! They owe me a full refund.

My husband and I purchased a Maytag Neptune washer and dryer set back in early 2005. It was our very first major appliance purchase together as a young couple. We were talked into going with the Neptunes as it was considered one of the high end models at the time, and it came with a 10-year manufacturers warranty, which by itself was a major selling point for us. We have now had our Neptunes for a full decade and I am happy to report that we have not had one single problem with either the washer or dryer the entire time we have owned them. In fact, they are still going strong to this day. However, as it has been 10 years, it is now time for us to upgrade. We have purchased all new kitchen appliances within the past year and we decided that its now time to upgrade our washer and dryer as well and go with a steam set. We will most likely end up selling our Neptunes since we will have no use for them once we get our new set. They have served us extremely well over the last 10 years and we wouldnt hesitate to buy Maytag appliances in the future.

I have had 2 Geminis. The first one was fine, this second one is a mess. I have had at least half a dozen parts replaced. I have insurance to have this oven repaired but have paid to have the window seal replaced on at least 3 occasions. The top of the oven is so hot that when I have used the burners to cook on top I have received 2nd degree burns. I have received burns on several occasions. I asked dealer if I could trade this in but said I would have to sell it on my own. I would not subject this oven to another person as I feel it is very dangerous.

Maytag Bravo 300 Quiet Series - Bought this Maytag 5 years ago because Ive always had good experiences with them. After 3 years it started making rattling sounds so we had someone come out and fix it for around $275.00. 2 years later its still rattling, leaving black grease marks and putting holes in the clothes. Will not complete cycle unless it is unplugged, reset and plugged back in. I give up, I just bought an LG. I will never buy another Maytag washer again, still have the matching dryer though.

Our less than five yr old washer finally died. It had been making awful sounds. Started in only very small loads but then started in bigger loads too. It finally stopped altogether. Model number MVWC400XW4. I would NOT recommend this washer.

I purchased my Neptune Washer in 2005/2006. I had a mildew problem, and the store told me to clean it with bleach. It is now 6 years later, and the ball bearings are going out. I called two different repair companies, and were told by both they would save me the call out charge, because the ball bearings were going out, and it would cost between $ 600-$700 to fix, so I may as well buy a new one. The washer is only 6 years old. This is completely unacceptable! I then tried to find someone online to fix it, and I ran into the fact that the Neptune Washers had a recall. Why was I, not notified? I bought the washer and dryer set from a Maytag store. No one tried to reach me. I am now stuck with the problem of buying a new one, and really cannot afford one at this time. I went with Maytag due to the brand name, and I knew it would be reliable. Is the joke really on me? Can someone please call me, and point me in the right direction?

Two years old, single person owned and will not operate - At 2:00 am, April 25th, 2012; I went to take a load of laundry out of the washer. It was still full of water and would not operate. I am a single person. I do not do load after load in two years. In fact, I was doing a weekly load of clothing, nothing large. I paid close to $1,000.00 for this unit. This sucks and why only one year warranty? Are you Maytag? A Youigo car would run better than this. And they are built cheap.

I spent over 2000 on a Maytag refrigerator. In less than 5 years, the coolant system has gone out twice! The only response I get is, “We are sorry, but it is 5 years old.” Are you kidding me? I have a 20-year-old fridge in the garage that is still working and I didnt spend over $2k on it! I thought Maytag was the best product out there and it certainly is not. Do not ever buy Maytag.

Save money. I have always had Maytag & loved them until I bought the Bravos xl top load washer. The salesperson insisted it was a large capacity energy efficient w/ great maintenance record -- greatly misleading. The water level does not rise enough to effectively clean or rinse so clothes do not get cleaned or detergent doesnt rinse out thus allowing only 2 to 3 towels or jeans to wash per load. Such ineffective cleaning cycles create the ongoing need for loads to be rewashed and be extremely small, yielding credence to other consumers’ accusations of being mislead and false advertising of xl capacity. As such, it takes hours to wash a family of threes clothes. The machine shakes like crazy and clothes get ruined as they get twisted and tangled into each other ripping, tearing, misshaping and ruining them.

I purchased a bottom freezer Maytag refrigerator two years ago. It recently began leaking water onto the floor from the freezer compartment. I just had it serviced and the serviceman told me that it was a common problem. The duck-billed check valve gets plugged. This is a problem with Maytag, Jenn-Air, Whirlpool, Amana, and KitchenAid refrigerators as they all share the same manufacturer. There is a service bulletin out on this that lists hundreds of model numbers affected by the problem (Technical Service Pointer #: W10632338). I think it is criminal that consumers are expected to pay hundreds of dollars to have this manufacturers defect repaired. I tried to find a place with the government to file a complaint, but wasnt clear who had jurisdiction. Perhaps a class action suit is in order. There have to be millions of consumers potentially facing this problem. Anyone with any knowledge of how to further pursue this defect, please comment.

Within the first year of having this washer (Maytag Bravos X series) the cam broke in it. And then about two months after the warranty went out, the motor quit. It wouldnt spin my clothes at all and would never get my clothes clean. I was having to hand wash my clothes just to get them clean. Not a very happy person, I live paycheck to paycheck and cant afford rock continuously pay to have my washer fixed.

I purchased this Maytag Washer and Dryer back in 2000 and have never been unhappy. It really gets my clothes clean and uses a lot less water than a top loader. The only issue is that if you do not clean it once in a while it will start to smell, but I have a cleaner I use every month and so far (knock on wood) it doesnt smell mildewy.

Shame on Maytag! Customer Service is appalling! Paid 2500 for one of their top of the line refrigerator/freezer and had the repair people 5 times in one year. It was determined that it is a bad model number that Maytag wont recall but knows it is faulty. Started with ice build up in freezer making it sound like a plane taking off. It kept running trying to defrost (energy efficient-right). The repairman put in a request to have the product replaced based on symptoms and freezer being at 26 degrees. We had to wait five business days for Maytag to review it. I have a family and was having guests. They told me to buy a dorm refrigerator and they would send me a small credit towards it in 4 to 6 weeks. They finally agreed to replace the known faulty model, but I have to wait for the exchange team to contact me (2 weeks later). I keep calling and leaving messages but cant get the exchange team to even return my calls. I have my sons graduation this weekend and I dont have a freezer and my refrigerator is faulty with all my vegetables rotting within two days. It also took two days to originally get someone in management to call me back (even though it did no good - she cant help me). You cannot talk to management if you call customer service. They downright refuse! What a company!

Never had a Maytag before I bought my house. So far the only complaint is there’s a broken piece that prevents the drawer from functioning. Otherwise, pretty good stove/range for the price. Do wish it was easier to clean without scraping anything up.

My Maytag Front Load Washer Model MHWE200XW purchased from Sears had a malfunctioning spin cycle. The authorized Maytag repairman from Landers, with support from a Maytag technician by phone, did not know how to repair it. The machine had light use over the past 15 months, and hence was not covered under warranty. So I am out $650 for the machine and $200 for the repair that resulted in continued and even worse malfunctioning. Unfortunately for me, the tests did not show any errors and the machine did not state any error. It just would not spin and then would not allow the door to open. It is a lemon and I do not recommend its purchase.

MDB4949SDM1 - After owning Maytag model MDB/C-2 for thirteen (13) plus years, I decided to purchase the subject Maytag Model when my 13 year old died. Big mistake. Previous model was very simplistic in rack design and it provided user-friendly options such as two detachable baskets for silverware and a special rack for delicate items.The new model has been designed so your dishes go in on angles on the top rack and as such bowls, small plates etc never stay in place once you move the rack and the lower rack configuration was redesigned and the rear area which was open to allow for bigger pots and pans to fit better has been removed, so now you have to lay your pans on top of the tines, very difficult to low the dishwasher.Additionally, I purchased the stainless steel model; apparently in the coating process a drip pattern was sealed that you can see when sunlight hits dishwasher. Further the stainless steel face that they bond to the door has popped, so when you grab the handle the face pops in and out. Lastly the new design has an adjustable upper rack; I tried numerous times to adjust the rack and couldnt so when I called Customer Service for these issues, it basically boils down to if the Service Man comes out and determines my issues are cosmetic and the rack which Ive never been able to adjust should happen to work then I have to pay the service call as there is not warranty coverage. So I declined the Service Call and advised that this would be my last Maytag purchase. I highly recommend anyone considering this unit fully investigate and test out before buying.

I purchased my Maytag 4 door refrigerator with the freezer at the bottom (model #MFX2570AEM) in December of 2012. A couple months ago it started leaking small amounts of water. I now notice that there is such a build-up of ice under the freezer drawer that it wont even close properly. I, like all the other consumers that have complained am fuming mad. I purchased the Maytag brand because of its great reputation for quality products. However, this is totally unacceptable that I should be having issues with this refrigerator less than 3 years later. Shame on you, Maytag!!!

Im an 78 year old man, married in 1962. In all the years and two kids we have had just three Maytag washers. To me the gold standard of quality washers. When the motor went out in our 15 year old Washing machine I considered replacing the motor, which is well within my capability. I am a journeyman industrial machine repairman formerly with Ford Motor car company before retirement.Instead, my wife and I bought a Maytag top loader high efficiency washer from Best Buy. I was skeptical when I examined the new machine with paddles instead of the agitator. Trusting that Maytag had engineered a water saving washer using paddles, I made the very poor decision to buy it. I regret not replacing the motor in my old machine. Boy was I wrong. Given the chance I would trade my new machine for the old in a heartbeat...The old machine washed everything we could throw at it. The new machine wont wash anything to my satisfaction. The bedding deep fill cycle is the only one capable of a passable job. Even then I would like a soak cycle which, in my opinion, would vastly improve results. In all I would characterize this as a total engineering failure. Why Maytag would allow this POS to be sold, where the reputation of Maytag is totally destroyed, is beyond my comprehension.

We purchased a Maytag dishwasher model number mdb7749sbm in April 2013. March of 2015 the controls stopped working completely. We looked online and instantly found it was a problem among many others, and said it was a result of corroded ribbon cable. We opened the panel and, sure enough, inside the ribbon cable the electrical wires were completely rusted through! We called Maytag, and, of course, despite the numerous complaints of the same problem, they would only fix it if we paid $250, or send us a replacement part for $350 to fix ourselves. Not going to spend that much on a dishwasher that already cost $600 and only lasted 22 months! We are attaching a picture that shows after we tried cleaning the rust (when Maytag refused to fix it) how much of the electrical wires disintegrated! We tried soldering a small wire to connect it again, but the ribbon was so thin it just melted right through.

Purchased Maytag Centennial Washer and Dryer (MODEL MVC300VWI) at Home Depot 3 yrs ago. After 6 months, washer started to rust. Maytag told us It was not their problem. A 6-month old washer should not rust! Poor quality + poor customer service. Dont buy!

Bought a Maytag top loader washer from Lowes in July 2017. Have had nothing but problems due to faulty computerized guts. Worked intermittently and took a long time to wash compared to older machine. Repairman out twice... replaced computer board and still have problems. The machine was made in Canada according to the label. Hey Canada, what is going on making junk? Too bad that we did not know beforehand what junk the Maytag brand has become. Lowes should not sell this junk to help its reputation and valued customers.

Maytag MHW3505FW Washer and dryer were purchased 13 months ago. I purchased and spent $2,000 because the Lowes salesperson and the stickers on the machine said they had a 10 year GUARANTEE AND commercial quality/technology. Exactly 2 weeks after 12 months the washer started flashing erratically when I was able to turn it on. Wouldnt react to any of the touch controls and stopped working. Called Lowes who told me because I hadnt bought an extended warranty they would do nothing. When I told them I was told a 10 year warranty was in place they said they only cover a year. I was told to call Maytag. Maytag said the 10 year warranty only covers the steel drum and motor! Nothing else is covered after one year. I was offered an extended warranty for $600. Not something I will be doing. I will replace with non-computer washer and dryer and will NEVER BUY MAYTAG again. They should be sued for false advertising.

I have Maytag refrigerator that is only 2 years & 9 months old that I am told by a service tech that it has a sealed system leak. So the unit runs it just wont get cold. I have lost all the food that was in the refrigerator & freezer and I told by Maytag that its not covered under warranty. The tech gave me a ball park quote of $600.00- $700.00 to repair the unit & I lost at lest $200.00 or more in food. I cant believe a new refrigerator wont even last 3 years & they wont fix their problem. So much for buying American made products. Whirlpool YOU SUCK & SHOULD BE ASHAMED!!!

Ive had the dishwasher model MDBH979SAB0 for about 3 years now. A few months ago I noticed the faceplate would pop out when you opened the dishwasher. I would have to pop it back in. The dishwasher was out of warranty so I decided to attempt to fix it. I took the faceplate off to realize all of the plastic tabs that screws go in to were snapped off. The only fix for this is a complete new panel from Whirlpool Parts Online to the tune of $194.17 (W10811169).The wheels also fall off the bottom rack. The push pin plastic becomes brittle over time and does not stay in the assembly. To replace the wheel assembly (there are 4 in total) is $38.18 each (W10195416V). The wheels or push pins cant be purchased separately. Both of these items are not covered under warranty past 1 year. Maytags 10 year warranty only covers the upper and Lower Racks (excludes cup shelf and silverware basket), chopper blade and stainless steel tub and inner door liner. So only a small percentage of the parts.The design of the faceplate is defective in that too much force is applied to the faceplate when opening the unit. The handle is integrated in to the faceplate. The plastic used becomes brittle over time and breaks. The panel unit (W10811169) must be replaced in entirety rather than just its housing increasing the cost of repair. To have this failure occur within the first 3 years of use is very premature. I can only assume if I repair the dishwasher I will have the same problem again. I am considering buying a new model that is designed better and comes with a longer warranty on such parts.

I too had to replace the control panel on my Maytag dishwasher which I purchased in 2007. I was told by my repairman to contact Maytag to see if they would do anything for me. When I called Maytag, I asked them if there were any issues with the control panels as I had heard there have been multiple issues with them needing to be replaced. I was told they had no record of any complaints and offered to sell me an extended warranty for $269, but there was nothing else they could do for me. I ultimately had my repairman order the part and it was replaced. My repairman did say Maytag did upgrade the panel because of all the issues they were having with the panel. Hopefully, they have fixed the problem and it will not have to be replaced again. But if it does, I will not replace it again. I will look into a new dishwasher and definitely not a Maytag. Yes, I would be interested in joining a class action suit.

Product number MMV4205DS. Beautiful, felt solid. Right away when we would put in a time to cook and hit start, the thing would say Open Close Door. First we thought it was moisture, and we would wipe the seal, then lifting the door a little helped. A month might go by and we would repeat this process. I did a little research and found the microwave is known for this. After the warranty was up, it got worse. My husband put a little screwdriver in the door clamp. The plastic guard that held the door shut fell behind the opening. Mulling over whether to call for repairs or buy a new one, we decided the latter. I am buying another one just like it, because the holes in the wall will match for an easy swap and it matches my suite. This time I took out the 3 year warranty, which I will hold Maytag responsible for any more problems. They say if they come and fix it 4 times in a year they will declare it a lemon and replace. I figure this will work in my favor because the microwave lasts a year!

It doesnt clean as well as the cheap GE model we have at our beach cottage. Also it is very noisy. Disappointing. Will never buy a Maytag dishwasher again.

The bottom oven of my Maytag double oven range (serial #MER6765BAS18) caught fire while I was baking there. The coil burnt out and separated. This did not occur due to food spill or other means. The coil was charred. The stove top does not perform adequately and the coils do not heat uniformly.

Failed after only 13 months with light use. I have a Whirlpool extended warranty which I had to fight to get them to honor. Then someone came to fix my washer and needed part was ordered, but part isnt available and company wont tell me when it will be. I have received 6 part availability dates so far. Whirlpool wont help. Over two months now without a washer. Ive asked them to replace machine or give me my money back, but they refused. The Whirlpool Extended Warranty group doesnt answer their phones, was put on hold for a long period.

Keep having the problem, the display panel tells me to close the door when the door is closed. I had a repairman repair it. 2 months later it started happening again. Im buy another microwave. It doesnt make sense to have it fixed again.

Well Maytag, shame on you! I just called customer service about the third repair made on my Maytag 4000 Series Washing Machine; its only two years old. The rep side stepped the limited warranty that is good for five years on the motor and tried to sell me another warranty for $329.00. I have $460.00 (parts only) in repairs. Purchasing a warranty will have me spending more money than I actually paid for it. The excuse that I was given was (per quote) our machines are made by people and we have no way of determining the outcome of our products past the given warranty. Maybe you should have considered buying the extended warranty that was offered at the time of purchase. Yeah, maybe I should have, but Maytag should build a product that consumers are happy with, and extended warranty sales past a longer period of time might make more sense. If you are thinking about purchasing any Maytag appliance, I would think twice or you just might get some person on the other end of the line that just doesnt care, representing the name of Maytag! I visit the Big Box Stores daily and you can bet your tail that I will make a special visit to the appliance section just to discourage any one from making the same mistake I did! Just think, the last washing machine that I purchased lasted for 9 years (not one issue) and it was still working when I gave it to someone in need! I have three appliances in my kitchen that are 11 years old, never had one problem with either one. Thank You KitchenAid! I should have purchased your washer and dryers!

The machine can clean even king size quilts, and clothes come out very clean. It is a front load and there are no problems with odors. There are many cycles to choose from. Cycles spin gently enough while getting out most of the moisture.

We bought a Maytag washer in 1987. It worked beautifully for years. The Maytag Centennial Washer we have now is sub-standard. It takes a full hour or more to wash one load. No quick wash feature. Today I filled the washer with soap, clothes, and pushed the button to fill it. It filled and inexplicably drained, wasting my time, water, and laundry soap. I regret buying this washer.

We purchased the Maytag double oven 30 inch 5 burner, stainless steel, model MGT8885XS. Oven worked good for six weeks. The igniter broke in the bottom oven and when the third party non-Maytag repairman came out to fix it, he was unable to remove the bottom oven door. It is not flush and heat escapes when the bottom oven is on and it causes the top oven to get condensation. The repair man was directed from a technician from Whirlpool that he had to order a new seal and hinges. I dont want it fixed. I want a new one. I have called Customer Service for Whirlpool and the third party and the store in which I bought it from and everyone is pushing it off onto someone else. Customer service is poor and stated they will only fix the oven and will not send us a new oven. We sent our rebate in the mail which was to arrive within 8 weeks and we have yet to receive it. Very poor customer service. Glad I purchased the 4 year warranty. I will never buy Maytag again.

Has anyone talked to an attorney to see if a class action can be filed? My fridge is leaking, sheets of ice on floor of freezer, and ice maker doesn’t work. Looks like it’s the norm for these. Please post if you have spoken with an attorney. If no one has, I am going to.

You get what you pay for, you can go cheaper with no frills and watch how clothes wash, also run afresh through the washer as recommended. Also use the correct amount of detergent. Maytag isnt as good as it once was but it is the top of Whirlpools line of companies.

The washer drum fills up with very little water, very little. I can do an entire load of laundry and the stuff on top doesnt ever get wet. Went on Spring Break in Florida and a month later our clothes still smell like the beach. Grill out, and I smell steaks the next time I put on the shirt. Stain your clothes in any way, its there forever unless you hand wash it first.To get it to work at all, each time I have to start the wash cycle (I leave the soap out just to save it for the next start), let the drum fill with water, pause it, get all the clothes wet, then cancel the cycle. After it drains and the machine is off and full of wet clothes, then start it all over again adding soap this time. On the second try, set at deep cycle, it will add enough water to cover the clothes - Im guessing because it senses more clothes because the clothes are now wet from the first, cancelled cycle. During the wash cycle, Ill open the lid and robustly move everything around, almost hand washing. #Handy. The dryer is fine, Im keeping it. The washer, cant return it - been three months of this frustration (kept believing it was me, reset it multiple times, change the settings, tried everything). Im buying a new one and throwing this junk out. $700 lesson.

I bought this Maytag oven (MEW 7627HB) to replace a 20-year-old GE double oven. Upon the first use, I found that it has noisy cooling fans which run continuously as soon as it is turned on and, for some time, after it is turned off. These fans make an irritating, loud, whistling noise. The dealer responded to my complaint, pulled the oven out and performed a complete system test. He then called engineers at the Whirlpool factory, who told him that the fans were a recent redesign made because the previous design didnt satisfactorily cool the electronic control circuit and that there was nothing to be done about the noise. After several weeks, the oven, when in use, continues to stink of overheated electronics. I fear it wont last long.Note that my old GE model, which also had electronic controls, didnt run a fan at all unless both ovens had been on for some time or the self-cleaning feature had been on for a while. And it didnt make a loud noise.

I am happy with this dishwasher. I had a GE that had a lot of problems. I insisted on getting Maytag and I have been happy ever since. It controls the time, temperature, and is easy to operate. I would like a bigger dishwasher because of my family size. This dish is okay for a family of 4. It matches my furniture. It blends in. No complaints. The digital pad is convenient but it has been fixed a few times. I had a few technicians who did not know how to fix. It was not the dishwasher, it was the technicians.

We purchased the Bravos XL Washer (top loader) and dryer about a year ago and have had issues with it since it was installed. Please note, we live between two homes so the machines are not heavily used at all. Our $250 machine we have in our Florida home works a million times better and is several years old. We purchased at the ABC appliance store and they have sent out a technician 4 times in the first few months. Bottom line, these are just pieces of crap machines. They cannot be returned! It is really a shame for the money spent and your clothes does not get clean on any cycle. The technician told us we should use the Deep water wash for all cycles which still does not work. I bought this machine for the XL capacity but also for the delicate cycle and stains do not come out, undergarments are still dirty, white power residue from OXI is left on the clothes etc... DO NOT BUY. This would get zero stars if I could. So disappointing and frustrating. If class action suit does happen, I would want to be part if it.

My Maytag dishwasher control panel stopped working. The control panel failed, it was replaced. The replaced control panel failed. The control panel failed again and needs a fourth (4th) control panel. I have had to pay for service calls and control panels. I only use it 1 to 2 times per week. This is obviouly a lemon. I would like it fixed and to be reimbursed for the lemon part and service calls.

I bought a Neptune washer and a dryer. I have had nothing but problems with these items since I got them. My washer keeps giving me a 3e code and will not clean the laundry right. I have used the H E detergent it requires and yet my clothes stink. My laundry smells like mold and mildew. I now dont have my units to wash and dry clothes. I paid almost $4,000.00 for the pair. I dont have the money now to replace them.

Two years ago I purchased a Maytag Top-Loading HE Low-Water washer. I have always taken great pride in the way my laundry looks and smells but since this purchase, my laundry no longer smells clean and fresh nor does it look clean. I have always used the same detergent and fabric softener (only now I use the HE version) and it served me well. I have read all of the directions and did as I was instructed. I cannot believe that anyone would actually think that you can do laundry with practically no water. Do the decision makers have not common sense at all? I didnt and still dont believe it but what choice did I have when all of the machines are now HE with low water. I think its terrible that consumers dont have a choice. I have come to realize that low water, HE washing machines actually waste more time, energy and money (detergent and fabric softener).My clothes are not clean, nor do they smell good when the wash cycle is finished so I have to wash them again, using more detergent, fabric softener and energy. The super fast spin that supposedly sucks out most of the moisture, also rumples my laundry with semi-permanent wrinkles (even on the low wrinkle setting) so clothes that never had to be ironed before, now need pressing. I find it remarkable that, with all of the detergent ads promoting washing clothes in cold water to save energy, we are told that if our clothes are not sufficiently clean in cold water in our HE washers, that we should try a warmer/hot temperature. Good luck with that because my machine has several temperature settings but only uses one - COLD! I cannot actually believe that with all of the technology that our society holds, we are going backwards in the basics of washing clothes. Terrible product, terrible quality, terrible results, terrible waste of time, resources and money. Why cant you just leave some things alone??

After only about a year or so - and it is out of warranty - the clothes are not clean - there are white type of scum marks left on clothes and especially dark clothes. This is even after I use the recommended detergent and less than normal and do a double rinse. Have to wash clothes again with no detergent with a double rinse again. Just so annoying. Would never buy Maytag again.

Maytag Maxima 9000 washer not working since day 1: I have placed a call on Friday, June 14, about my Maytag washer not working. The service man came in on Friday, June 15, 2012, and stated that a UI board needs to be replaced. I have called Whirlpool to ask for the part to be ordered so it is faster, could not do anything. Then, I have not heard from Whirlpool since. I called them again on Wednesday, June 20th, and I was told that the part was ordered and it will take up to 10 days for it to arrive. Once it arrives, the technician will call to set up an appointment. So, according to Maytag (Whirlpool), I can be without a washer for at least 2 weeks (as 10 days are 10 business days) and it is all good.

One year ago I bought a Maytag Micro-wave and a Maytag dishwasher - big mistake. I should have done some homework. I had problems with the dishwasher since the day it was installed. I should have suspected something was wrong when it was delivered. I opened my front door and there stood a deliveryman holding my dishwasher in his arms. He said, Where do you want it? I couldnt believe he could be carrying it by himself, especially since it took three of us to move out the old Thermador which by the way was still working just fine after almost 30 years. But my wife insisted on a new washer for her new kitchen. The Thermador was actually made of steel. The new Maytag was made of plastic even the motor. It had some steel and copper parts but mostly plastic. I dont think it weighed forty pounds. The problems began the first day with leaks through the door and under it. I suppose eight or nine service calls happened in the next 3 months. The factory service men were different each time and each had their own guess as to what caused the leaks. Over time they replaced all the parts that could be leaking some of them twice, because subsequent servicemen discovered that a previous service man had installed the wrong parts. We often had to wait several weeks because replacement parts were not on hand, and would be ordered and shipped directly to us. Then we would have to schedule another service call, only to find out the wrong parts came - more delays. One service man told us we were using the wrong detergent, even though it was the detergent and spot-free rinse that came with it. Another service man removed the door cover so he could watch to see where it was leaking when it operated. He said the soap was foaming too much and flooding over, so we had to try another brand of soap, even though by now we had accumulated three other brands that were just barely used. The service men never did fix the problem. It took much experimentation from my wife to stop the leaks, which meant we could only use a fraction of the recommended amount soap. By now we were using so little soap that the dishes always came out dirty. So our choice was mop up a wet floor or have dirty dishes every time. Most of the time now we wash the dishes in the sink. One service man said in Maytags effort to make the dishwashers more efficient, and less expensive to build that the motor and pump were way under powered, and everything was made from petro-chemical by-products (cheap plastic) and that we should invest in the extended warranty. Its cheaper than paying service calls when the warranty runs out soon. What we should have done was exchanged it for another brand. My wife said had she only known, we would have never replaced the old Thermador which will be my next dishwasher. As for the micro-wave there are many things I dislike about it especially the rectangle glass tray which is extremely awkward to remove and replace each time you have to clean out crumbs and spills which happen often. The timer on/off bell is way too quiet with no volume control. The message and operation display is difficult to understand. And to top it off the cheap plastic handle broke one week after the warranty ran out which I found out that its less expensive to buy a whole new door than pay for parts and a service call to repair handle. Maytags track record made me not want to deal with service dept. again. I will probably be money ahead to trash the two appliances, start over and do some homework and maybe buy a European made appliance. I know German technology is not all about profit making, but quality, reliability, durability. I hate to sound un-American but greed in American corporations will be their downfall.

We purchased a Maytag refrigerator model # 1TXEGMYWOO. The refrigerator part froze all of the food in it. We moved the temperature selector to the last place (two notches away from the recommended setting), and the food still froze. The furniture store we purchased it from replaced it with another refrigerator (same model). And that one did the exact same thing. We had to throw out more groceries. Obviously, this model is defective. We are now waiting for the store to replace this one (with a different model and brand). They have been very good about trying to make things right for us. Maytag, however, is a different story. They were very rude and indifferent when I called to complain. Their policy is to repair or replace the part (temperature gauge). I dont want a new part. This is a new product. And I bought it expecting it to work. I have had to throw hundreds of dollars worth of groceries away. I was very disappointed in their attitude. I will not purchase another Maytag item again. They used to have a good reputation. They now sell inferior products and do not stand behind their products.

BROKE AFTER 3 YRS. Purchase a new Maytag model: MVWC425BW1 top load washer and dryer after just 3yrs of use. It failed and to find out this is a common problem with these new open drum washers. The bearings go out. Be aware do not purchase them and they also do not wash your clothes good, clothes just stay in same position and you have to wash 2-3 extra washes. It was going to cost 350.00 plus to repair so I purchased Speed Queen that has good reviews. Tech said that top load open barrel washers have been a nightmare.

This is a wonderful washing machine. For cleaning clothes it does exactly what you expect from a washer. We have had 2 Neptune front loaders. They, however, have a couple flaws I dont want to live with again and will be looking for one that has come up with the solution to them. One, the bearings on them need replaced on a periodic basis or it sounds like a 747 taking off. Two - the front gasket around the barrel has a mold problem no matter how much you try to keep the thing clean. Other than that, these machines perform fantastic.

I bought the larger capacity machines to save time because Im so busy with my family and wanted to cut down on loads. I was surprised to find the capacity can really only operate at half, which is as large as my old, smaller machines. The washer is extremely sensitive, meaning it may take four or five tries (this morning was four) to arrange the clothes - even a small load of delicates - in it in the exact way the machine wants before it will allow the cycle to start. This is exceptionally frustrating, particularly during the busy morning or when you are tired at night. So you have to stand there and wait until the sensing function is happy and you see the water pouring in. Yet often you will return to the machine and it will have an error message that occurs inexplicably during the spin cycle, so the wash cycle will need to be restarted. It cannot just be continued. The machine is not only a huge time waster but a water/detergent waster as well.I learned that the sensing function on the dryer is useless as well after coming back to many loads of damp clothes that sat there, got little funny smelling as a result, and had to be rewashed in the nightmare washer lol. So now I just use the timer function. It takes about two hours to dry a regular load of towels, so be prepared for that. I bought Maytag because it is an American-made product, but I wont make the same mistake next time. If the quality is any reflection of the functionality, it probably wont last very long anyway. Heres to hoping.

I had a Maytag dishwasher (made by Whirlpool) that after 4 months of ordering wrong parts, parts arriving damaged, and parts that were re-engineered and did not match up, the dishwasher could not be fixed. The extended warranty people (AIG) promised me twice on a recorded telephone call that they would exchange my dishwasher, and after many many heated telephone conversations was given a 20 minute lecture on how the word exchange does not mean they will replace it. The frustration ultimately overtook my misspent loyalty in anything made by Whirlpool and I decided to accept the buyout of my extended warranty contract, at a loss of hundreds of dollars to me - well worth getting rid of that dishwasher and any further affiliation with Whirlpool corporation. Absolutely horrible customer service. Unbelievably god awful treatment. I dont know what happened to customer service at Whirlpool, but my dealing with them has convinced me that the term is an oxymoron at Whirlpool. Horrible horrible customer service. I have never been treated so poorly in my life. I truly dont know how they can still be in business if they treat their customers like they did me.

Need to keep cleaning washer otherwise it leaves white marks on clothes. I used vinegar but that didnt help. Used the wash cycle and that didnt help. I found a washer cleaner and it works great. Overall performance of washer is fine but I would be hesitant on purchasing another Maytag Bravo washer only for this reason.

Bought the matching washer dryer set thinking would be energy saving and reliable. Two months after warranty ended it quit, press pause/start button, no reaction. Started looking online and found out this is Maytags Frankenstein. Checked obvious stuff like power supply. Wont be buying another Maytag product EVER. Dryer still works but washer dead. Am retired, low income. Cant afford expensive repairs. Maytag ought to be eating this, not the consumer.

I have a Maytag Bravos XL and have white residue on all the clothes that get washed in this machine since I purchased it. I have always used HE Detergent and have followed all Maytags recommendations to reduce the white residue to no avail. I had to wash my clothes 5 times to get the residue off of my clothing and 4 of those were without any detergent and on all temperatures and wash cycles. Model # MVWB835DW.

Just replaced a washer that lasted over 7 years thru 3 renters with the Bravos top loading washer. There is nothing efficient about a cycle to take 73 mins to wash 20 articles of clothing (t-shirts, socks and underwear). The machine dont wash the top of the load. Also the deep clean feature isnt deep cleaning. I recorded a video of 20 mins of the machine not washing properly before going into rinse cycle. If this item dont produce refunds of the amount of water wasted RE-WASHING and electricity because it doesnt clean on first wash, then its time for Maytag to pay my utilities. For the money spent on the machine, going to the laundromat every other week with 1 roll of quarters each trip comes to be I can wash for 4 years and will outlast the longevity of the machine before it breaks! Also bulky mode is how you get more water in the machine but will take 63 mins to wash.

I am online now because we have the same problem. Our refrigerator is less than 2 years old. Watched a video on YouTube how to fix problem and repairman said engineers who created design must have been on drugs. I think hes right. Very common problem. Have to call repairman!!

The big problem is Lowes and Home Dopey, I mean Depot. I am an appliance repairman for 30 years. Their machines are built to a lower spec. Buying same machine from mom n pop store will help! Will cost you more but it will last longer with less repairs! P.S., While Maytag does make some of their own appliances, when Whirlpool bought Maytag years ago they shut down the Newton, Iowa plant. Whirlpool builds that washer and puts Maytags name on it. If you want a good washer buy a Speed Queen, go online and check their reviews! One more thing, LG and Samsung build terrible appliances. Do yourself a favor and stay away from them, just saying!

Really havent had any problems. The Maytag repairman really is lonely. Great quality wash machines and dryers for that matter. I havent had to do anything. Spins well... Very quiet, no complaints. Dryer works well too. Many cycles area to put fabric softener and bleach. It has a extra extraction cycle and many other features.

Nineteen months in a home of empty nesters and the darn thing is a game of trying to outwit its electronics. We live a long way from town, which makes service calls a high dollar thing. I have spent considerable time this weekend trying to cipher its moods and order parts. This washer was purchased on an invalid reputation. Others beware.

I have a Maytag dishwasher model mdb6759aws3. The control touch pad broke after 1.5 years of light use. It costs $475 to fix (includes labor). Completely unacceptable service provided by Maytag over the phone. The only concession offered was a 25% discount if I bought the replacement part (control touch pad) from them. After some internet research, I learned Maytag marks up their parts prices over 25% so they are really not giving you a discount at all.I filed a complaint with Maytag but they were unable to provide me with any evidence of doing such except for an 11-digit code. Due to a major defect, Maytag should have sent me the replacement part for free. I told Maytag I thought this was fair and that I would pay for the labor. I will never buy another Maytag appliance again! They are junk and the company does not practice common sense customer service.

Maytag Bravos XL Washer & Dryer - After a long 45-year use of our old GE W./D. that were still working fine when we decided it was finally time to upgrade. Big mistake. Nothing but dissatisfaction on every level of complaints by those who registered here before us and then some. This all was noticed almost immediately after purchase, but we lived with it trying not to believe our worse fears. That is until we both started breaking out with skin rashes. Just logged on this site after a Google search... We were shocked and disappointed in our purchase decision. We will join in a class action lawsuit if ever one is initiated... Any lawyers with one of these?

I have an HE Maytag Bravos X washer and it cleans very well. But compared to my previous washer, with an agitator, I like the old one better and the clothes came out of the washer far less wrinkled. I would not buy another HE machine, given the choice.

Below is the message I submitted to Maytag on 5/6/2016 at 10:00 a.m. ET and just received an answer via phone call today 5/9/2016 at 3:30 p.m. ET that Maytag will be doing nothing. Also, my husband has still not received a call about the drum seal and when Maytag can come fix this part that broke in their machine only months after purchase. I will let you read my message to Maytag and you may decide if you would like to buy their dryer after reading what I sent and knowing they will be doing nothing. (Washer works just fine).If this message could be passed onto customer retention and/or management, I would greatly appreciate that action being taken. My husband, and I purchased a Maytag Washer and Dryer Set from Lowes in (Listed Location) on (Listed Date) (Model Number: MGDC555DW2 and Serial Number: **). The dryers drum seal has already gone bad on one side. We had a Maytag servicer come to our home on Monday, May 2, 2016 to confirm this and said he needed to order parts and we would hear back from him on my husbands cell number in a few days, which we still have not received contact. Additionally, due to the drum seal going bad, a whole load of laundry has extreme tears in the material to the point of being ruined. I have pictures of the clothes/sheets and drum seal, however there is not a location on this contact form to upload them. I have three work shirts, worth around $30.00 each and new bed sheets just bought in the amount of $77.39 which have full threads pulled through them due to the dryer going bad in only four and a half months of normal usage. I am writing to request compensation for my items that are now unwearable/unusable and would be glad to provide pictures and receipts for price of items. We of course have not used the dryer since, which has been a huge inconvenience, especially with no update in knowing when the dryer will be fixed and reusable. Please contact me back in regards to my request. Thank you.

I purchased a Maytag Bravo Washer and Dryer about 2 years ago; dissatisfied with the products. Washer continues to smell. I clean it all the time with the Affresh tablets. Usually, I have to use 2 bags just to get it not to smell for at least 2 weeks. Now, the glass front dryer is rusting out around the window.

I bought a brand-new dryer Maytag Bravos. It broke after 3 weeks. They came to fix. A few months later, same thing happened, but I have 6 people in my house. They told me someone would be here the next day, and then that person canceled. They called someone else. He came and said I have to wait 3 days for parts. I called at least 6x and waited 30 minutes each time. They kept telling me theyd call back, and theres absolutely no call back. Then I called corporate Yvette, who was totally cocky and rude (866 817 5404). She said she would try to get back to me another day because she had meetings! Then, I was irate. I mean how rude. So she called me back and said, I ordered you the parts. Now you call Dan Marc, the service company, and make the appointment. Is this woman kidding? Then she went on about how Maytag has a 13% rating (They are Maytag.) and how their product is so wonderful. Now this woman is competent cocky and rude, and shes the presidents secretary! So whatever I call Dan Marc, they have no appointments Tom and wont make me an appointment. This is how a new product should work? I asked her what I do when it breaks again and again and the warranty is up. She told me they dont work on what ifs and if that time comes, it will be her decision. I am disgusted and have a house full of kids with no dryer? And I have given them another chance after that Neptune disaster. Im appalled and dont even know what to do.

My first job was at Sears but went elsewhere to buy Maytag. I have had only 3 sets of washer/Dryer in 50 years. The set I have now are over 20 years old! I am looking at a Maytag refrigerator now.

Our Maytag Atlantis dryer had smoke coming out and almost had our house on fire! Had it not for us double checking the entire house would have burnt down! The dryer is less than 10 years old and already it is tearing apart. I cant risk using it again. Terrible company. I would never buy Maytag products ever again!

My old Maytag is still working after 20 years but my husband surprised me with a new pair! Washers is just pure junk. Not enough water to hardly wet the clothes. They just rub together and get worn out looking, towels are rough and not soft but my biggest complaint is the AWFUL wrinkles! I have to iron everything! Only had it 3 days, called Menards and asked if we could return for an exchange or upgrade and they said no. If this is the best American Made has to offer, then I will look at the Samsung! Shame on you Maytag. Not one good review on here and you do nothing to restore confidence in American Made. I will spread the word - NEVER by a Maytag or an appliance from Menards. Neither one stands behind the piece of junk!

This oven has been used so very seldom that I didnt feel I could rate it until now. We use the oven 1-2 times a week since purchasing it in March of 2018. There hadnt been any reason to use the Self Cleaning part of the oven until last week. I have had a oven with self-cleaning for 20 years and the oven went out so we purchased this one because of its sleek look and features. However last week I decided to use the self-cleaning setting on it and came home after being gone all day to find that the house smelled like it had a fire burning in it. I ran to the oven to find the whole inside cover in a white powdery substance. It looked like a snow blizzard had gone on inside of it. I was use to a small amount of white residue being inside the oven after it finished and it just wiped right up. We spent hours vacuuming it out then scrubbing it down with vinegar water and a sponge with a scouring pad on it. The casserole spill was still on the bottom, most of the enamel is gone and the glass will not clean off. I did not use any chemicals in the oven prior to turning it to the self-clean mode, I believe that it overheated and burnt the enamel off and distorted the glass. Whirlpool offered to send me a cleaning kit. I told them that would do no good. I had already scrubbed and used a razor blade to try and clean the bottom and the glass and them sending me different cleaning supplies would not fix the fact that 80% of the inside protective coating on the oven is gone. Now it is a porous surface. A Serviceman was scheduled and he called prior to arrival today and asked me to explain what was going on with my oven. I explained and he said I can almost guarantee that Whirlpool will say that it is cosmetic and they only cover cosmetic for 3 months and that I will have to pay for a $100.00 service call. This is a load of crap. This coating is part of the oven to keep it clean and protect the metal from the high heat of baking in it. This is not cosmetic feature like the outside stainless steel finish or the black trim decor. The inside doesnt look pretty. It is a function. See the photos below. Whirlpool Range Item # 805150. Model # WEE510S0FS.

I inherited this Maytag washer, so it has been around a very long time (I have had it for 18 years). It still runs quite well, has 3 levels of wash/rinse, 3 cycles to wash in. Both of us...me and the washer are still kickin together. Highly recommend Maytag.

Purchased Maytag Bravos Washer in 2013. Used a little over a year and had to put it in storage for 2 years. Biggest piece of junk Ive ever had. Ive had cheap washers that lasted more than 20 years! Repairman said all diagnostics read normal. I put a very small load in to show him the water was not even wetting the clothes and only swishing them around a little. The shirt on top never got wet and was still in its same position when it went into the final spin. He said this is normal. He recommended I dump the machine and find an old NON Maytag model with the tall agitator!!! Ive tried using all the settings combinations; and the water level never gets all the clothes wet and clothes do not get clean. Will NEVER buy a Maytag product again.

I purchased a Maytag dishwasher on Nov. 5, 2013 from Freds Appliance. I had to have the control panel fixed twice and it failed again in June 1916. My stemware had a film on it and I either had to wash it by hand or rinse it in hot water and dry by hand. Thus I felt like how could my other dishes not have this film on them even though I faithfully used Finish. I have 2 daughters who live within a half mile of me and they did not have this trouble with their dishwashers. I always felt Maytag was a top brand, but I replaced my 3 year old Maytag with a Whirlpool that my daughter and her family of 4 used for 19 years. Guess what... my glasses come out sparkling without using Finish and they wash in half the time and are dry!

Purchased a Maytag range with Aqualift technology in 2013 thinking it was a good brand and *happy* to find a new way to self-clean my oven. This turns out to be nothing but a joke and I am not *happy* with it. After following directions to the letter, there is some loosening of anything on the floor of the oven, but the sides and top are slowly being coated with more and more grease. Ive spent way too much time with my head in the oven trying to scrub stuff without using a heavy duty cleaner but feel I now need to resort to Easy Off as there is no other way to get it clean. I also dont understand why they tell you to remove the racks since there obviously isnt enough going on to even clean the oven... How would the racks be damaged? And now I believe there is a problem with the Dual Choice element where Im not able to turn the temperature down. Even turned back to the low setting, the pan cooks away like its on high. I have to keep turning it off and then back on in an attempt to find something similar to medium or low heat. Im so very disappointed in Maytag and feel this method of oven cleaning should never have been put on the market. Its a scam!

We purchased a Maytag Bravos Quiet 300 about 8 months ago and it will not clean anything. Not one setting will make this machine clean. You have to wash everything 2 to 3 times. There is no savings of any kind with this machine and I dont know anyone who has the time to wash everything multiple times. Its all about the water; its about as much as you can spit. I ran a hose from the faucet and added 8 gallons about 10 minutes into the wash cycle and was able to clean (float) a set of sheets. I find this energy star machine to be worthless and I would have been better buying an old machine at a garage sale than this Bravos machine. Junk. If you cant float your cloths folks, you might as well be rubbing them on a rock.

I bought a new refrigerator and when I plugged it in would not cool. I called and the authorized tech came and said the compressor was bad and the evaporator was rusted and hoses were greased up. I have now been informed that the warranty was void because it was put in a dental office and not a single home. I said since it was never used I would put it in a house. They said it was void and I was out of luck. I always thought maytag sold good products but this has convinced me to never buy a product from them again. It never worked and the tech said it should be replaced but they said he should never had told us this.

Washer was delivered Feb 2016. (First one delivered Jan 2016 with damage.) Home Depot HEAVILY promoted this model - we paid $600+. This washer has NEVER thoroughly cleaned clothes & now does not drain completely!!! Theres always lines of dirt left on clothes - you can see dirt clearly on dark clothes. Washer does NOT fill with enough water to thoroughly wet clothes! (Even on the bedding, extra dirty settings!) Clothes smell clean because the detergent was not washed or rinsed out. Washer does not agitate, turn over or rotate clothes... It gently shakes the tub side-to-side (like a mild earthquake does the ground) which does NOT move clothes around. Home Depot salesman said it strongly rocks clothes turning them around and under. It does not do that! You have to stop washer and PHYSICALLY move clothes from center and turn them around so bottom of pile gets wet (Now I understand why this model has a see-through lid!!!) This model is supposed to pre-wash sense the load amount by shaking the tub side-to-side to gauge how much water is need - FALSE ADVERTISING! I put gallons of water in two loads (same bulk & weight of clothes) to see if more water would be used on the heavier load - results: the same amount of water was used on both loads. Now (Oct 2016) the washer is not draining completely and going back to wash instead of rinse, drain! Maytag Corporation just says theyll send a repair person out but this is a SMALL town & the repair shops theyll use here are sketchy!This Washer is a huge waste of money just to own laundry status tone bells & non-usable settings. Its probably in violation of OSHA health/safety codes because if there are chemicals, feces (sorry, but wheres theres kids...), blood, diseases (if you visit anyone in a hospital), etc on the clothes... Those things are NOT being washed out of the clothes, so youre being infected by touching improperly washed clothes. WHY is there not a RECALL for this appliance? There are many, many people having the SAME problems as us. This is our first HE top-loader and I wish I could afford to get rid of this & buy a washer with an agitator... But alas, we still owe $300 on this worthless (albeit fancy-looking) appliance. :( Maytag XL HE top load Washer MVWB835DW (Does NOT clean clothes!)

Bought this Dishwasher two years ago. Control panel was working intermittently now it does not work. I am looking for anyone with this same problem. I know lawyers who are class action specialists who fight for the consumer. We need to make Maytag responsible for the flaws they have in their product. From reading these other reviews it seems that this control panel issue is consistent no matter what model you have. They must all share the same electrical components that is causing this issue with the control panel. My model number is MDB8959SBS2.

I purchased my microwave in 2012 and have had to have numerous repairs, mostly with the open/close door switch error. It is now 2018 and I see that the same problem is still occurring! Maytag obviously hasn’t read or doesn’t care that this problem has existed for years and they choose to do nothing about it. This past week when I had the microwave running, the beep went off indicating the popcorn was done but when I opened the door the microwave was STILL running! I thought it was a fluke but it happened again. Tonight the open/close door error once again appeared on the display. Having already had this repaired to the tune of over $150, not to mention the danger of a microwave running when the door is open, I called a mayday on the Maytag! I decided enough is enough and went out and purchased a new microwave... Obviously NOT a Maytag. The dangerous inoperable Maytag microwave is in the garage waiting for trash pickup.

We purchased the Maytag Atlantis used (4 years old); it looked like new. When I opened the lid, I noticed a terrible smell like some left the clothes in the washer for days. I used white vinegar, baking soda, bleach, anything to try and get rid of the smell. Nothing worked. Finally, my husband took out the agitator and then the drum. Inside and around the drum was lint from all the years of washing clothes. He scraped it all off and bleached it and put it back together and it was okay for a while. It now smells again and I am afraid we will have to keep doing this or our clothes will always smell. I also leave the lid open after a wash so Im not attacked by the smell when we open it. I also had the Maytag Neptune front loader years ago, and the water pooled by the gasket on the door. That smelled too! We will be redoing our laundry area soon and will be shopping for a new washer and dryer. It will not be a Maytag!

less than 2 yrs old and has completely failed to operate. We have been patient with this model. It does roll the clothes to point they are wrapped around and among each other and must be pulled apart before placing in dryer. The wash cycle now takes more than 45 minutes, It fails to spin the load often. Now, it has failed to the point it will not operate with or without any clothes in it.

My wife was in the kitchen and started yelling for me to get in there fast. I could smell smoke and then could see the smoke in the kitchen and sparks coming out of the front top right side of the dishwasher. I shut off the power to the dishwasher at the breaker panel. I then removed the contents and then the dishwasher itself. I threw it outside and then the next day I took apart the door and found that the control board was melted and fried. The model # is MDBH949PAM1. We are trying to locate the receipt for date of purchase. Pictures are attached. This is not safe and my wife is very upset as our 4 year old daughter had been leaning on the door not just 15 or so seconds before this happened.

We bought this he Maytag washing machine about 3 years ago. I have hated it from the start and should have put a review right away because it is a piece of cr#&. It does not save any energy because I have had to rewash loads because clothes come out still dirty, lint still on them, sometimes even dry spots on clothes. I did a wash today and chunks of HE detergent still in the clothes. I am rewashing a load right now. I now have to do a presoak hoping that will help the load come out cleaner. So dont waste any money on Maytags HE machines as I will never buy another one.Being an environmentally conscious person, I thought HE was the way to go but it doesnt save any energy when you have constantly run a laundry twice to get clothes clean. It also does not do a good job spinning as clothes are still very wet. I hate this machine and I am thinking about junking it even though it still runs. Very bad purchase.

I have been very disappointed with the 2017 model of Maytag washer and dryer as the washer does not clean the clothes as it should. There is the inner part taken out with no agitator and I believe that is the reason that the clothes comes out not white or cleans as I am use to it being before with my other machines. I think they need to reinstall the agitator to clean the clothing thoroughly. The dryer takes longer to dry the clothing and it uses more hydro which cost a lot more monthly for us to have to pay out. I will never purchase another washer and dryer as this in the future.

After researching the top-rated washing machine in consumer reports, we decided to spend the extra cash ($930) and buy the top-rated machine. Spending almost double on a high end machine, you would expect this machine to last longer than three years. The motherboard needs to be replaced because it gets stuck on a UL code near the end of the cycle. Now, we have had two people come try to fix it, and they said to trash it and buy a new one. Only three years! If I had paid $300, I wouldnt be so upset, but that was a total waste of money for it to last less than any machine Ive ever had. How is a consumer supposed to know what a good washing machine is if they spend extra cash for the top-rated machine and that one is still bad? The company should replace something like a motherboard that goes faulty when it had nothing to do with use. So unfair and frustrating.

Our Maytag lint trap started falling apart a few months after we received it. Call Customer Service to get a replacement due to the product being faulty. The answer that I got from Customer Service: We sell you a new one. Poor customer service, faulty product. Dont buy dryer from Maytag.

We purchased our Maytag dryer at Home Depot a couple of months ago. We just called Home Depot for the second time because the dryer handle broke off while opening the front load door. We called Maytag and they tell us to call Home Depot and the only thing they are willing to do again is fix the door handle which will probably break off again while Im in the middle of laundry and cant retrieve clothes from the dryer because there isnt a handle to open it.Im convinced the dryer has a defective handle, and the dryer should be replaced considering what we paid for it. But Maytag or Home Depot doesnt want to do that. I will never buy Maytag products again and thinking of buying products at small appliance stores who stand behind their products, instead of Home Depot who could easily turn our dryer over to the insurance company as defective for the loss.

I bought my Maytag dishwasher on September 4, 2013. In August 2014 the control panel went out. (Sound familiar?) The dishwasher was still under warranty, so I called Maytag. It took 3 tries to find a repair person who would come out on my schedule. (Im a teacher and cant take time off.) They installed the new control panel, and it working. I tried to submit a review on Maytags website, but my review was denied. I guess they didnt want to hear the truth.

MHW7100DW Maytag Washer Steam & YMED7100DW Maytag Dryer Steam. Both of them are easy to use. They hold lots of clothing as well as bedding and many different settings. They both do an excellent job. Brand and excellent reputation. Had my last Maytag washer & dryer over 25-years and had no problems with either. Thats why I bought Maytag again. Repairs are very costly when you have to pay technicians. Dont like poor quality construction or enamel chipping when you place items on them. Very easy to clean both of them. Practically no lint dust emitted into the room from the dryer. Had no problems with my previous washer & dryer. Thats why I purchased a full size Maytag washer and dryer again.

We purchased a Maytag MVWB765FW top load washer with agitator to replace a Whirlpool with premature gear case problems (less than 3 years old). Was partially sold by the attractive metal label that says 10 YEAR limited warranty. It is now less than 2 years old and the Maytag selected repairman just diagnosed a failing transmission and of course advised us this is not covered by the warranty. Cost to repair—$ 600. About as close to false advertising as I have seen.I can’t believe that this company would sell such crap and not stand behind their products! But after seeing all these other complaints I believe it now. I bought both washers from Nebraska Furniture Mart and I realize they only sell the appliances but I plan to inform them that if they continue to handle Whirlpool and Maytag products they will never sell another appliance to me or to anyone else I can influence to not buy from them. We as consumers are almost powerless against these manufacturers but if we can influence the stores we buy from, just maybe we will see some improvement.

I bought a new Maytag washer two and half years ago. One of the new HE (High efficiency) models. Clothes do not get washed clean. But not only that, now its not washing at all. My previous machine was a Maytag...Had it for 22+ yrs. I guess Maytag quality is no longer what it used to be. Disappointed customer!

Last August I bought the Maytag Bravos XL. I have had 3 repairmen try to fix my problems with it and they cannot. The problem is, they cant fix an appliance that isnt designed correctly! Without water, one cannot wash. Dont be mislead that the huge area inside can be used for large objects like sheets and comforters. This machine is MUCH harder on my sheets and comforters than my old machine with a center agitator. I have shredded rugs, holes in sheets, black lines on clothes and a chlorine dispenser that puts spots on everything. The detergent dispenser hardware is rusted as well. Folks if this machine was an automobile, IT WOULD BE RECALLED!

We bought a Maytag dishwasher on 9/22/2012. Model number MDB7759SAB. Within the past couple of months, it has been very temperamental. The control panel started beeping continuously and some of the functions wouldnt work anymore while others continued to work too well; in that the dishwasher on occasion would rewash several times without anyone starting the machine again. The dishwasher also started leaking water... As of yesterday, the dishwasher control panel stopped responding and then out of the blue, the dishwasher turned itself on in the middle of the night! We called customer service and they said they could send a repairman out for around $89 and then we would have to pay for the parts needed and the cost of labor. After reading many reviews sounding exactly the same as mine, my husband and I are against repairing this lousy machine. Its absolutely ridiculous for a dishwasher to quit unexpectedly like this. Our question now is, which brand to purchase for our next dishwasher? No more junk please!!

I bought our Maytag HE washer model #MVWC565FW back in July 2019 after having owned a Kenmore scratch and dent washer from Sears for approx 25 years, and in just one month of using it I knew it was a mistake. There are only 2 water levels - deep water (full tub) or practically no water (though there are a number of settings, there is no difference in water level, its just full drum or very very little water). The auto-sensor water level option is a joke - there is barely enough water to wash anything - its like going back hundreds of years to washing and beating your clothes on rocks. Items in the washer become so tangled it sometimes takes a while to detangle before placing in the dryer. Water stops filling the tub when lid is open - I can no longer wash and rinse delicates while the drum is filling. It took 3 calls w/ Customer Service to get an ADDITIONAL lid latch that I can use to trick the machine to thinking the lid is closed - I keep the actual lid open, then stick in the lid latch I bought - take it out when Im done hand rinsing. This also enabled to to view the washing in action - IT DOES NOTHING! Clothes stay in the same place as you placed them in the tub - they dont move, they dont wash - and I bought a washer with an agitator - that is in quotes because it is a misnomer with this brand! The wash cycles ARE SO LONG it takes all day to wash a few loads of laundry. Once you select a setting YOU CANNOT CHANGE IT - the washer empties and stops, then you have to start all over again - ENERGY AND WATER EFFICIENT...REALLY???? What a bunch of you know what! This is the most inflexible piece of junk I have ever had the displeasure of owning. I have to keep jugs of water on hand that I keep filling up to at least have a bit of water. When I called Cust. Svc. at the beginning telling them my experience - the person on the phone had nothing to contribute - they couldnt even tell me what cycles might fit my needs - they told me to go back to Home Depot and ask someone there! WORST APPLIANCE WORST COMPANY.

I purchased Maytag microwave model MMV4205AAQ in 2005. I use it infrequently. It stopped heating in Nov. 2011. It must be replaced. But after this experience and reading other comments, I will not purchase any Maytag appliances in the future.

Maytag Bravos MCT washer not good - Owned this since June 2017. This thing has never worked properly. Every time after a cycle is complete we have to wring the soaked clothes by hand. Even after doing this the drying time ends up being double what it should be because the clothes are so wet. Not only time wasted on hand wringing clothes but also wasted energy in drying them afterwards. Also this thing is supposed to auto-detect how much water it should use but half of the time it uses too little water and doesn’t actually wash all of the clothes. Some clothes stay totally dry when this happens.

We went to Lowe’s to buy a new washer when our old front loader would’ve cost more to repair than was worth it. This Bravo XL washer is the biggest rip off EVER!! I, like others, have watched with a flashlight & see that most clothes are nowhere NEAR being wet AT ALL!! Let me tell you... I am BEYOND LIVID!! I bought this washer thinking we could wash our comforter at home instead of a laundromat and WHAT A JOKE!! It would never even wet a FOURTH of a queen comforter, let alone the whole thing!! My husband had to actually LEAVE HIS JOB to go home and change because his shirts smelled like a wet animal! People actually were commenting on the smell!!Believe me, we tell EVERYONE how ridiculous this whole energy saving scam is!! AND... I am having to wash clothes TWO and THREE times to get them NEAR smelling normal!! My electric bill and water bill have gone up substantially and again, I AM LIVID BEYOND WORDS!! We spent over $900 for this washer with the extended warranty!!! NEVER EVER AGAIN WOULD I BUY MAYTAG!!! And I have tried EVERYTHING to try to rectify this; I added less detergent, I’ve used the deep water wash, extra rinses. I’ve had the Maytag technician here replacing the circuit board thinking perhaps THAT would give me more water. I sure wish we could all do something for SO MANY of us being taken advantage of!!! Did I mention I’m FUMING?!!?

This a 28-month-old bottom freezer fridge purchased from Home Depot. At about 26 months, the freezer started to leak water as ice was completely covering the bottom of the freezer floor and the excess water would then run out once the door was opened. I managed to get the ice out with slim bladed putty knife and did this about every 10 days. Contact with Maytag affirmed that I had no warranty available as it only comes with a 1-year, except for the compressor. Every effort was made to sell me an extended 1-year warranty for $330, and then a technician would be sent to fix the problem. I asked if the compressor had failed, would I be discounted as it is warranted and the answer was no, the fee was still $330. I had great difficulty in explaining why I would purchase a warranty for an item that is already warranted to no avail.I decided to go with their 2nd option of having a local appliance tech to solve the problem at my expense which I did for a final cost of $130. Technician came and immediately knew the problem and removed a little black rubber stopper valve that is supposed to let water pass but gets clogged and the water backs up into the freezer. It took him all of a half hour to fix everything, $85 for the visit and $45 for time in place, $0 for parts. He stated that this is a continuing problem that he has seen many times. Moral: Dont buy any Maytag products as the Maytag repairman who had nothing to do has died.