I bought this washer (Maytag HE) almost a year ago, and if I could redo my choice, I would not choose this machine. There is no separate spin cycle. Often items are left with quite a bit of water in at the end of the wash cycle (often literally dripping as you transfer to the dryer), and you cant just rearrange them in the washer and then spin again. The only option on the washer is to both rinse and spin, which almost never helps get out more water. So you then have a heavy load in the dryer, much longer dryer time, and higher utility bills to get some loads dry, especially bath towels, sheets, jeans, etc. The washer is large capacity, but if you fill it more than 1/2 to 2/3 full (depending on the heaviness of your items) the spin cycle definitely will not get nearly enough water out of the clothes. The lid on the washer is SLOPED!The most ridiculous design I have ever seen for a washer, everything you set on top, even for a moment - laundry detergent, folded clothes, wet clothes - ends up on the floor. And the lack of agitator means at the end of the cycle, some loads that contain a sheet or any large flat item (tablecloth, etc.) the rest of the items are captured below the larger flat item that is over them like a mushroom cap. You cant tell how long the items have been like that in the washer, but its hard to imagine they are getting properly cleaned and rinsed. You absolutely cannot use powder stain removers, especially OxiClean, unless you are using the oxi cycle (much longer than regular cycle) because with any other cycle you will have white cloudy patches on all your clothes and items where the powder dissolved in the water but did not rinse out. You have to manually scrub them out, as putting these items through another wash cycle does not remove all the spots.

We were delighted with our new Maytag refrigerator, model #MBF2258XEB, until the compressor died less than a year after we bought it. Home Depot, where we purchased it, directed us to the A&E Company for service. Two weeks later, we are still without refrigeration; Maytag refuses to replace it and even refused to overnight the new compressor. We thought Maytag set an industry standard for excellence. Don’t buy this product if you want a reliable refrigerator from a company that stands behind its products.

Bought used and still performs like a champ. It's old. Have the matching dryer but that quit working some time ago so I hang dry clothes.

We have had our washing machine for about 6 months, we got the F3 E6 error code. After doing some research, we found out that the control module was what we needed to replace. My husband and I called both Maytag and Lowe’s, (the store we purchased the washer from). We have been given the runaround. After talking with several managers in the Lowe’s warranty department, we were told that we had to contact Maytag directly about that particular problem. Okay, no big deal. We called and every single time we were put on hold for at least 30 minutes before we were hung up on. Not once did we even get to speak to a person. If we don’t get a response and our problem doesn’t get fixed, I will be going to the Better Business Bureau.

I bought a new Maytag dishwasher 9 months ago from Costco - Maytag 24 in. Built-in Dishwasher with PowerBlast Cycle, White. This dishwasher needs a new motor - Please do not buy this dishwasher. It is garbage.

I had a tub failure on my washer Whirlpool Duet, which I bought brand new and it lasted 12 years with no problems. The dryer is still in use at my sons house. However, this failure lead me on a search for a set to replace the duet. I did some research and found the Maytag 6.2 Cu. Ft top loader and huge Dryer to match. The set was not cheap and it did have high marks for a great washer. So, I bought them both and had them delivered on 12/30/16. I have read all the owners manual and watched YouTube videos to see how to use this machine with all its pretty lights and sounds. I will concede that the machines look great, very impressive in my laundry room. I would bet it would even be a plus when I go to sell the house.THAT is all the nice stuff I can say. The machine does not clean clothes and I have done all the settings. I have changed laundry detergents, and even tried to add a little more water with a bucket at the start of the wash. (Saw that one on YouTube.) REALLY. That did not work, nor should I have to do that to get it to clean well. The answer seems to be, set the machine on FULL tub of water. So, I tried that for a couple of times and found that the clothes just float around and since they do not touch the Wear Plate they dont get clean. My wife (yes, I am a man that does most of the laundry) said she hates the washer and I was an idiot for buying this expensive piece of metal that does nothing but take up space and leaves spots on your clothes. Have you heard the term Happy Wife-Happy Life. Well not so much for me now.Spending money even $2,500.00 on a washer and dryer seems a little crazy. But I had the extra money and I have always wanted a MAYTAG. These guys know how to make a washer. Boy was I wrong, this machine must be an embarrassment to Maytag. I know I am really shocked that you would sell this machine as top of the line. I am not sure what Maytag will do, but I thought I would give you a chance to make this right. I have attached pictures of the machines installed and pictures of the model number plates. I have faith that Maytag will step up. My wife said this was a waste of time. The ball is in your court Maytag. (Come on Maytag let me win this one.) - Just a man and his dirty clothes.

Maytag Bravos Quiet Series 300 washer/dryer - Purchased this set nearly 3 years ago from Lowes. The washing machine smells like toxic sewage. The Affresh brand cleaner no longer works. All of our towels and many of our clothing items have had to be replaced due to the stench. I surmise this is because it does not use enough water. The clothes get wrinkled badly, twisted, stretched out and torn. The dryer does not fully dry. Always had to run it again to get the items dry. Finally, it started making a horrible, loud, screeching and grinding sound. Neither the washer or dryer was quiet for long. Putting these out on my curb today for scrap metal pickup.

I purchased a Maytag fridge with a freezer on bottom. As you know there are many complaints regarding ice build-up in freezer causing leakage out onto the floor. I will not purchase Maytag again. For 3 years I have fought the ice buildup and it has ruined my floor! Poor design - should have been recalled!

Maytag never fails to please me. My dishwasher is so quiet I sometimes have to put my ear next to it to make sure it’s actually working. The inside is stainless steel (those are the quietest) and it has a child lock so my 2 yo grandson can push all the buttons he wants and he still can’t mess things up. I love the high temp and sanitize features and everything is always clean and dry when done. It seems like it takes a long time to run through all the cycles, though. That and no adjustable top rack are the only two things I miss with my previous dishwasher.

Purchased a refrigerator freezer in 2012. It freezes the refrigerator contents, ruins vegetables....freezer doesnt freeze the contents....stopped making ice. Clicks on and off every two seconds sometimes for twenty minutes......

Had previous Maytag for years. Good, reliable, easily repaired product. Cycle sequencing very recognizable. New washing machines are ridiculously designed. Neither you nor the repairman have any idea what the cycles are or if they are even working as designed. Many cycles start out trying to wash with little or no visible water in the drum (top loader). The clothes come out tied in knots. I now wait for the agitation to start then pause and add water for three to five minutes then restart. What a nuisance. I have called customer care many times and they are courteous but not very helpful. This machine is an engineering nightmare. If I were in charge I would retire the people who dreamt up this contraption and get back to something reasonable before all their credibility is lost FOREVER!!

Our 26 month old Maytag fridge (Model MFF2258VEM8) was the french door freezer on bottom modern style fridge. The freezer stopped working. The repair shop took the fridge away and repaired a leak (quality control issue) and then the compressor failed in a test. They wanted $700 to make a repair that would have a 90 day warranty about 1/2 the cost of the fridge. Maytag was contacted at multiple levels and they would not even provide a free compressor or provide a substantial discount on a new fridge. What a way to treat a customer who once had all major Maytag appliances in our home. We decided to get a GE Profile fridge and are very happy with it. I will never buy another Maytag appliance. I dont think it is the great company it once was years ago.

This model MGR5875QDW range is very difficult to use. When you press broil for instance, the display says set. There is absolutely no indication of how to set. Therefore, no broil. The same thing happens when you try to use the clean function. It is virtually impossible to use the control panel; it is just too difficult. Therefore, most of the functions are not usable.The kicker though is that the handle comes off. During the extended warranty period, a technician came out and fixed it. The toughest part of this job is to get the oven door back on. I tried for 2 hours everything I could think of. Then, I got an idea to use Maytags live chat. They told me that I would have to call for service and pay for a service call to get the door back on. I told them that their clean cycle is too painful to use, so I am assuming I am not the only one who has removed the door to clean the oven. Pay for a service call every time I want to clean my oven or fix their defective handle design because the handle falls off every 2 years? That is not acceptable.

It had always been my wish to own a Maytag washer and dryer as they were considered THE BEST! Well was I wrong!! I am on the third stainless steel drum, this one has a hole in it, need 4 wheels and pulleys, with service $542.61!!! On the average, I am having a service call every 6 months - last year we were gone for 6 months so no laundry was done, one drum was delivered and was egg-shaped. Maytag has been NO HELP! I am very disappointed with Maytag, their service and product. They HAD an excellent reputation, to me that is everything. Quality, customer service, and their word means nothing to me anymore.

We bought a new Maytag Bravo series thinking we were buying the best product... not! The washer has been running great. But when it came time to clean the washer on the Affresh cycle, the washer overflowed. It turns out the washer fills up higher on the Affresh cycle than it does on the regular wash cycles. Well, that’s why it overflowed; the plastic tub that hold the water had a freaking crack in it near the top! This washer isnt even 3 months old. I had to get a repairman in here once to check it out, then again to come back and fix it. At least it was under warranty. Im afraid what else will happen. Piece of crap Maytag, great quality checks! Maybe hire some real people that can see what the hell they are doing in quality. I told them about the damages to my basement. They sent me paperwork to fill out. Forget it, the paperwork gives you the runaround!

We purchased this terrible machine 2 years ago. The clothes come out worse than when they went in! White powdery stuff all over darks! I always have to wipe all dark pants down with a wet cloth! Absolute junk! Really bad product! Never buying from this company again!

We have had a Maytag dishwasher for just over a year. The control panel acts up randomly and has finally quit altogether. The design of the handle is very poor as it pulls the control panel away from the door. Will never buy a Maytag product again. This is a very clear design flaw and when we called Maytag they offered no help as we are passed the guarantee.

Does not wash. Only very small loads get washed even though it claims to wash bedding. Some clothes NEVER get wet. Many times the clothes have to be rearranged and re-washed AND extra rinse. Cycles are over an hour each (then multiply x2!!). Maytag service has been called MULTIPLE times. They replaced the touch pad then the computer board. Both times saying the machine works “according to design/specs”. This is a Very poor design. Maytag should recall this inferior machine as it does not perform the job it is being sold for.

My 20 yr old Kenmore washer broke last month so I replaced it with a Maytag I bought from Lowes. I wanted a simple washer that would maybe last 10 years. The Maytag has a sensor for everything. So you can’t fill the washer, it determines how much water to use and it never fills enough to cover the clothes. It doesn’t agitate really. It’s more like a slow on & off movement. It does everything in an on & off way. The water fill goes on & off, it “washes” on & off. Even the spin is a spin, slow to almost stop - spin again - almost stop - spin again. It also stops filling if you open the lid, I tried to let some water fill before adding clothes (so the liquid detergent could dilute a bit) but every time I opened the top there was no water in the drum, I heated the water running and the drum was wet but it wouldn’t gill at all. I think it only puts water enough to “sense” the clothes have been soaked. I will call Lowes and try to return it.

I absolutely love this Maytag Bravos XL washing machine... I bought this machine before doing any research because of a sale and then after reading multitudes of reviews... positive and negative... I thought I had made a mistake. The absolutely most important thing with this machine is to load it properly and select the proper wash cycles. You must stack your clothes around the outside of the drum leaving the center open. You must use HE detergent. This is a Commercial grade washer and is meant to be loaded. The twisting and wringing of clothes is because of the high speed nature of the spin cycle (commercial). If you have never been to a public laundromat then you should try it and see what those machines do to your clothes. I too was apprehensive about the water levels at first... So I stood there for an entire cycle multiple time and on diff settings.The machine is constantly adding water as needed and each time after about 10 min... no matter the size load I put in. The clothes eventually were covered by water. Have had no issues with clothes that come out dry in spots. I suspect this is due to improper loading. Again my info on using this machine... loading techniques etc.. all came from positive reviewers stressing the importance of these key factors. This machine was not designed or intended for light or delicate use. So if you do a lot of those type loads perhaps this machine is not for you. As for the loudness and banging I have read about I have not experienced that. I have read reviews that the problem in some case ended up being metal or plastic drip pans used under the machine. Mine sits on concrete. Anyway hope this helps someone out.

We bought Maytag refrigerator MTB2195 AEW in 2006 for a hefty sum. The store where it was purchased was closed. The place where it was serviced was closed. We have had seals replaced, fixed, etc. twice. The freezer is full of ice balls hanging. The refrigerator doesnt keep as cold as it should and stays steamed on glass. I had a repairman again today and was told that he cant fix it. The frame will not stay tight. Theres a 3/8 in. drop from left side to right. It cant seal properly. You have always been a great product. Whats happening here? What can you do for me; Im at wits end. I have an older refrigerator in the basement thats 26 years old and is still going strong. I need something done quickly as I dont want to wrangle with this ice any longer and shouldnt have to. Please give me your attention on this as soon as possible. Kathy

The $1,100 Maytag Bravo XL does not have a dedicated spin cycle. Its rinse and spin. When out of balance, you rearrange and it rinses AGAIN - 15 minutes - before you know whether its balanced. By rinsing again, it can redistribute to be out of balance. Repairmen (w/ extra warranty) said you cant wash bath mats, bedspreads or pillows though it had giant capacity! They would charge me if I called again about it (3 strikes). So bought a used Kenmore with no computer panel... Its great! My dealer had the Maytag hauled to a dump, he would not sell it to anybody as he had integrity.

I bought this Maytag French door model MFF2258VEW2 in 2010. Within the first year, it was freezing my vegetables. They sent someone out to fix it. Thank goodness it was under warranty. The man laid the bill down and it was over $800 to fix it. Six months later, it froze up. I called and they said they would send someone out, but I would have to pay for it. Im on disability and cant pay that kind of money. I got someone to come out and fix it. Well, guess what? It has started freezing my vegetables again. This is the third time this thing has gone bad. What do these people think they are doing putting things out like this? I had a Maytag for 30 years and never had any problem with it. So I saved and saved to get me a new one but I will never buy another Maytag. The company should have to replace all the refrigerators that are like this one.

I read the reviews before I bought this washer, went to a major department store to buy it. This way I knew that I could get good support if something happened to it. Its been 3 months, I use the washer everyday. There are 4 adults in my building, they use it daily. I have never had a problem yet, the clothes come out cleaner than the front loader I have. It seems Maytag still makes a good product. I am the first to admit, when you make large number of products you will have some with a defect. But this washer the Centennial by Maytag works great.. Plenty of water in the tub, the clothes come out clean.. Maybe those people having problems need to stop buy at big box home centers. Theyre known for lumber not washers.

I bought a new refrigerator 6 weeks ago and it is not cooling or freezing anymore. I lost all my food. I spent 50 minutes on the phone to be told that the earliest they can fix it is in three days! Can you believe that? I will never buy a product from Maytag or Whirlpool again and everybody should be aware of the awful quality of their customer service!

I bought my maytag stove model MGR7662WS on January 30, 2011 and have had it serviced 3 times... same problem. I set oven to 350 degrees, put food in oven and later check on food only to find the temperature reads 350 but the oven is cold. Food is not cooked and it smells like gas. I turn it off and turn it back on and it does not turn on most of the time. Service guy keeps replacing parts and says he will replace the same part he just replaced last week. He says sometimes the part comes out defective. I think the stove is defective and I have thrown away so much food because it does not finish cooking and smells like gas. Its so frustrating because my Thanksgiving was ruined two years in a row due to turkey not cooking.

Bravos X high efficiency... efficient at not cleaning your clothes, efficient at ruining clothes, sheets, towels, may be efficient at being a boat anchor. Maytag offers nothing. Have had washers last 20 years or more. Someone, or some atty. General should bring a class action suit. Horrible product. Dont buy one. DONT BUY MAYTAG/WHIRLPOOL. THEY DONT TAKE CARE OF THEIR CUSTOMERS. JUNK. That report was very fair as requested. You really dont want to know how I really feel.

Besides the fact that it barely agitates or turns over the clothes even on deep fill (which we need every time otherwise a whole HE cycle goes and the top clothes remain DRY), the oh-so-fancy power button stopped working at less than 2 yo! And guess what, because it is not a button or knob, but control panel sensor button you hover over to turn on, the fix is to replace the $400 little control panel box. On a $600 terrible washing machine! We trashed it and bought something else without a faulty button system. Very unhappy. Do not buy this.

MAYTAG REFRIGERATOR SAFETY ISSUE SHARP EDGE Maytag refrigerator model MRT118FFZ01 purchased Feb.2018. There is a safety issue, sharp edges. Maytag has been aware of this for over 1yr from customer reviews. I went to consumer affairs.com and there are numerous complaints on products/customer service. I have been asking for a replacement door since Feb. On Sept. 7th I cut the palm of my hand on sharp edge, drew blood, no stitches but I was very upset. Called Maytag, transferred to the safety dept. sent out service tech. He reported that it was a safety issue, very sharp edge, he had to put duct tape on corner to prevent any more injuries! He requested that new doors(freezer&refrigerator door) only be sent, I do not want/need the whole unit replaced. Freezer door has sharp edge also. I have numerous emails to/from corporate office begging since Feb. for a new doors so that this would not happen! Maytags solution is to buy back refrigerator or I should pick another model. Neither is a solution for me. I picked this model for a reason. I asked them to provide me with the simplest solution which is to contact factory where it is made, red flag it, talk to manager, quality control check to see that there are no sharp edges before it is shipped to me. They refuse to do that 1 simple common courtesy, customer service request! They cannot guarantee that door will come without a sharp edge! My model is not the only 1 with this problem. I talked to salesman & model in store has sharp edge & in the reviews the same model had sharp edge which was submitted over 1yr ago! So Maytag has been aware of this safety issue for some time now but chooses to do nothing about it! I chose Whirlpool because of the name, I thought it stood for quality & above all excellent customer service. Was I wrong, found that out thru numerous phone/email conversations. They just dont care! Is it too much to ask Maytag to give me a refrigerator with no safety issues?!!! I have talked to Aaron in the corporate office, he was no help at all. His # 866-817-5404 ext **. I have all the emails to/from him. Please help, I want this same refrigerator, only model that would work for me. Now that I have had personal injury & have spent so much time/effort, aggravation since Feb. trying to have them do the right thing I feel that I am due monetary compensation. Bottom line this complaint is concerning a safety issue & horrible customer service from the call center to corporate offices! The Maytag name isnt what it used to be known for, quality & service.

The top of the range has blistered and has worn off. It cannot be cleaned. I spoke to a Maytag representative and was told to try and use magic eraser to clean around the burners. This did not work. The model number is mgr7775xs. Is there any solution to this problem. My range looks terrible.

Dryer needed to be serviced within 2 months. Drum seal fell out. Service was no questions asked. Fixed promptly. Washer works fabulous. Gets clothes clean. Surprisingly quiet. You do need to keep up to the sensors on the dryer. Must be wiped with rubbing alcohol to keep performance.

The mid level dishwasher is excellent, easy to install. Very quiet. The dishwasher cleans well and does a great job. I wish the default would go to the last setting instead of auto. Highly recommend.

Bravos 4.3 High Efficiency Washer - The worst washer ever. I recently returned from burying my step-mother. She actually used the same washer and dryer, by Maytag, for over 50 years. Those days are gone forever. This is my second set of Maytags in ten years. The first literally stopped working just after the first year warranty ran out. I still have them inside my pantry, like a set of anchors. Notwithstanding that, I thought, Maytag was a good brand, it must have just been the style of machines, so I purchased these in January. After over six months of usage, I am amazed at how many times I have to wash a single load of clothing to get the items clean. Who cares if the machine saves water? What was wrong with having an agitator? I literally have to remove freshly laundered clothing, turn it over and run the wash again to get the top of the laundry clean. I have had a blanket finish for the fourth time to get it clean, only to have to hang it outside because it is so full of water, the weight keeps it from spinning properly. And why would you remove a timer feature which permits very busy, working people, to wash their items while they are on the way home or in the middle of the night so that there is no waiting to pop the clothes in the dryer? None of the cycles takes less than 80 minutes to complete. Who has 80 minutes to wait on the washer to do its job? I am so upset about the amount of money I spent on all of these machines. Just think, I could have brought the over 50 years old set home from my step-mothers and had a washer and dryer do what they were supposed to do -- clean the clothes.

Model mdb7749sbm. Unit is just over 1 year old and fails in the same way everybody else in complaining about. Here is my question, this failure mode is obviously a designed in feature providing planned obsolescence to the device. Why is this company not being held to account for the damages in this case? Are all the judges that bought that no suit can be brought?Have all of you contacted your state consumer protection organizations regarding this issue? I would also recommend that you write both your state senator, the state consumer protection organization and any media outlets you can think of. High rate of control panel failure, devices activating by themselves when people are potentially away from the house, risk of fire or flooding... these are serious things and I would think a story that some news organization would surely be interested in digging into. Now that would serve to light a little fire under the Maytag organization if something like that was to occur.This sure seems to me to be a defrauding of the consumer - selling them a product at the top end of the price range that has such a significant design flaw that in the end can only be considered not fit for purpose. I havent yet contacted Maytag and Home Depot (who I believe are fully complicit in this as well), but I will be doing so to give them a chance to make this right, which I fully expect them to decline to do. Then I will begin writing letters. Am also considering small claims court. But above all, do not just accept this and move on! Companies like this need to be held to account, and they need to be reported so that others purchasing new devices in the future know to stay away from them.

Yesterday, the main compartment of the refrigerator is not cooling. The freezer still is working. This unit is 2.5 years old! I have never bought an extended warranty before, but on day one, this unit hardly ever shut off. It didnt seem like the electric bill was any higher but never felt good about the unit. Plus, I hated the ice cubes all over the floor when I pulled out the lower drawer. The monitoring device is in the roof of the fridge and takes up a lot of square footage. Nope, will never buy another Maytag. If their products cant last more the at least eight years, then it is such a waste of our money. Do better! Im writing Consumer Report and the President of the company. Who replaces all the food loss?

I renovated my kitchen 3 years ago. I decided on purchasing new appliances which included refrigerator, dishwasher, microwave, range, washer and dryer, all of which I got from Maytag. Of course they were always known for dependability but apparently they were not! What happened to this American product? In the last 3 years, I have had my refrigerator (**) serviced 4 times for the same problem. Each time servicing has been a nightmare at the hands of AE service, Preway service and of course at the helm of my nightmare Maytag Customer service. The first mistake I made was purchasing Maytag products followed by the second mistake of purchasing Maytag service contracts. I now have a refrigerator that is not working, waiting on parts since end of august. When I called Maytag customer service, they confirmed the parts were not available and recommended I go online and try to find the part! This added insult to injury. Today, Preway service finally came to install my parts and upon technician’s arrival he opens the part box and realizes he ordered an ice tray cover, when he should have ordered an Interface Control Board. Maytag continues to have their products serviced by incompetent companies and appears to have no interest in keeping you as a customer after you purchase, whatever happen to the dependable people?Maytag had built their reputation on reliable products and dependable service, what happened to this American Made appliance? Here is a prime example of what happened, and why companies like LG and Samsung are gaining more and more customers every day. The best advice I can give someone is avoid Maytag. By the way, I forgot to mention I have 2 small children ages 3 and 4 and Maytag is not concerned about how I would provide food for them with a refrigerator that does not work. Shame! This is not what I expected from what I thought was a reliable company.

Please do not buy a Maytag washer top loader. It does not get enough water and it does not clean your clothes. It is the noisiest cheapest made machine out there. If you have kids you really need to bypass this one. I have had this for 10 months and its only me. Please especially if you have children stay away from it. Im the most unhappiest camper Maytag ever had.

We purchased the Maytag MDB8959SAS0 dishwasher about 2.5 years ago. A couple of days ago, the lights on the control panel started blinking and beeping erratically. I contacted Maytag and they said the control board likely needs to be replaced to the tune of around $250, not including labor! We spent $800 on this dishwasher and it cant even last 3 years?? Ridiculous. The only other advice the service rep. had was that we should have bought the extended warranty. Gee, thanks. I guess with Maytag, you really DO need that extended warranty because their products are junk. I think I will just scrap this dishwasher and go with a Bosch. We also have a Maytag range that needed servicing after owning it for only 18 mos. And a Maytag dryer that needed servicing after a month (at least that was under warranty). I will NEVER buy a Maytag product again... they are complete junk.

My oven smelled for weeks after being installed. The first time I self cleaned, the oven stopped working and the door remained locked. It took weeks to get it repaired because we needed a part that had to be ordered. The second time we self cleaned, the oven smoked, set off smoke alarm that had to be disconnected, the control panel bulged, and the door locked. It was Sunday. I wrote a nasty email to Maytag. The service man who came Monday could not unlock the door, and said he had to order a part and would return the next Tuesday if the part arrived.Next, I had warranty issues. I had to get a copy of the purchase receipt from Home Depot to prove that the oven was still in warranty. Out of the blue, my phone rings on Thursday and it was Joe ** from Maytag in Michigan. He had read my email, said he was sorry for all the problems, and if I did not mind waiting 2 to 3 weeks, he would send me a brand new oven, would have it installed, and would have the old oven sent back for inspection. I did not mind (although there is only so many things that can be grilled or you can bake in a toaster oven). Three weeks later, I have my newly-installed new oven with its new, year-long warranty. Thank you Mr. ** and Maytag for the great service.

The first washer my husband and I ever purchased was a somewhat cheap top loader but it worked very well for over 10 years. We decided to fall for a bargain sale at Home Depot and went with the HE Bravos model. We were told that it would save us money and work great! From day one weve had issues. It never really seemed to clean right. It gets thrown off balance if you have more than one bath towel in a load at a time. After an angry call to the company and a somewhat helpful customer service rep, I began washing every load at the deep clean heavily soiled cycle and then did an extra rinse to boot. So much for energy efficient. So, fast forward 4 years, I HATE this washer but cant justify a new one at this time. Now, it stops mid cycle and I have to unplug it then plug it back in and restart it. When this happens, there is an awful smell. Needless to say, well be buying a new washer within a week or 2 and you can bet your life, it will NOT be a Maytag.

13 months after purchasing my Maytag dishwasher, it started operating by itself. I woke up one morning around 2:00 to it working, and I know I didnt put it on! I only use the auto clean cycle (that decides how dirty the dishes are, and is the cycle you use to conserve water). I dont use heat dry at all. Anyway, now I go to use the dishwasher and even though I press the auto clean button, the normal/heat dry/delay start buttons flash on. I try canceling this cycle out; sometimes it works, sometimes it doesnt. I dont see Maytag as reliable anymore.

We have had our oven for seven years this past October 2015 and has now been down for three weeks. Last February 2015 (8 months ago) we had to replace the bake igniter because the oven would not get up to temperature. The most recent incident happened a few days after Thanksgiving (2015), I was cooking dinner and noticed that the oven was not reaching desired temperature. I then opened the door to see if it was hot inside the oven and when I did it must have ignited making a huge poof and flames came out at me! Thank God my 12-year-old daughter had walked away from cooking with me to answer the telephone because the flames came out exactly where she had been standing!!!I contacted Maytag and explained what had happened and how we could have had an explosion or someone couldve burned. The first questions they did ask me was if anyone was injured or any damage to our house?!?! I was happy for that however, it also told me that this has happened before! They called the Maytag repairman in my area and supposedly made it a priority call in which he could not come until 12/10 which was two weeks after this happened. Therefore, my husband and I contacted a different appliance man who came out and told us it was the temperature sensor. Since fixing it, the oven works ok and cooks properly however, when initially lighting/igniting it is extremely loud and makes a very large/huge poof! Its as if the oven is filling up with gas and eventually lighting! The other night when I lit it to show my husband it was so loud that it rattled the door and he immediately turned off the gas to it. I googled this and it said that its basically a mini explosion where the oven is filling with gas and then igniting! Its to the point that we could lose everything we have worked for just to make a meal! We spend over a thousand dollars on our beautiful stainless steel convect oven. Its gorgeous and when working works great however, Im petrified to use it now because Im scared to being burned or exploding! Now we start over and yesterday on Sunday I contacted the original Maytag repairman who said to call back Maytag again and hell come immediately. Maytag originally told me on the phone that they would cover labor and the service call however, ironically enough they did not write that in the dispatch order! Im outraged! What will it take before its safe for our family and home! My husband is ready to junk it and buy a GE however, we do not have the money especially before Christmas to do so. Oh and let me add that the first week we had the oven we had to call them for the window seal to be replaced because it was hanging. So now seven years after owning it and 10 months apart we are having major issues. What happens if its fixed and a year later it happens again? It could explode in our home!!! SCARED & IRATE WITH MAYTAG & WHIRLPOOL.

Dishwasher could do better with washing the dishes better and less recycling time. Also, it would be better if it had a self cleaning unit on it.

Like everyone else Im calling corporate. Mr Fettig he should be in hall of shame after these complaints with their defective product. My fridge leaking, ice maker broken, water everywhere and eight inches of ice. I wonder if he owns a Maytag himself? Oh well after a while he might have a flood on his floor. This should be recalled just like my first model in 2001 that was a fire hazard. I had to go to the top then and I will now also. We should be protected from buying garbage while he makes 4 million a year.

Bought machine 03/23/15 exactly 2 yrs ago & machine will not work. It looks like the electric panel and which there are a lot of complaints about the panel, and the lid. It seems as its about the extended warranty now. The quality that Maytag advertises is lies. You buy the product and you have no choice but to purchase a warranty on your machine. Simple is better when it last 20 yrs over 2 yrs on a fancy machine. First electric panel machine washer with a horrible experience. It will cost 98 just to look at, that is not including parts and labor. Its 339.15 for a year warranty which equals over 300 per year for 3 years. Overpriced in all ways. Worse choice ever.

So I read the reviews when I bought this Maytag Bravo Washer and figured stuff happens. We bought the top load Maytag Brava in 2013. We bought the Home Depot warranty, 2 years later the washer was leaking water. 5 repair visits and 3 attempts to fix the leak before it was repaired. As of 4-25-17 the wash machine displayed un-level errors and started vibrating with a thundering noise. Called out warranty repair and they stated we need new bearings. Repair is scheduled in 2 days and now the wash machine is thundering and spewing oil so it is shut off. 4 years old, and like the other complaints clothes come out with dry patches and not clean. This is a bad machine, we are saving for our next washer. It will have an old style spindle/agitator, no California efficiency and probably not Maytag.

We bought this washer before Christmas. I was very excited. However my clothes don’t come out clean. I am actually washing my white uniform with hands because each time I wash, dark scums remain on my clothes. I think that the machine sensor does not sense how much clothes are in there and how much water is required. This machine is very disappointing, it needs to be recalled. See pictures below.

I purchased this Maytag Bravos XL Washing Machine at Lowes in California, MD for about $800 on April 8, 2018. What a disappointment for a Made in America product! BUYER BEWARE - DO NOT BUY! I agree 100% with the reviews and comments. This washing machine is a PIECE OF JUNK! It does not clean clothes! It does not provide enough water to get all clothes wet! All it does is shake the clothes back and forth and stays in the same order you put the clothes in. I agree with one of the reviews that it does nothing but crumple/wad the middle items together and rub them. And the clothes are DIRTY!! I will be calling Maytag 1-800-344-1274 and demand for my money back!! Lowes should STOP selling this product!

MODEL: MFI2265XEM1 - ice maker dispenser leaked water while under warranty; took two separate technician trips to repair. Several months later, called Maytag regarding leak and ice at bottom. Technician replaced w/ grommet w/ larger dia drain tube extension; smaller dia causing backup of water & ice. Now, ice maker quit working completely, ice buildup in bottom part of refrigerator and freezer building up frost which means air is getting into the freezer, and yes, the freezer door is completely shut! Please advise if there is a class action suit. Will contact California Attorney Generals office.

My Neptune dryer purchased in November 2005 had the drum crack at about three years old. I complained so much that they finally agreed to send a replacement drum for free. Now, two years later, the drum has cracked again and tore through the housing on the front of the dryer. The repairman said it would be too expensive to repair. Consumers, beware.

This Maytag Dryer (Model #MEDP575GWO) was delivered January 29th and the paint on top of the dryer is bubbling and peeling. I haven’t even had the unit 4 months yet and they tell me the warranty for “cosmetic” reasons is on 30 days. This is completely unacceptable and I will sue them if necessary. I am in utter disbelief.

Dishwasher control board - This will be the 3rd time for this same failure with the start/resume button on control panel. Obviously, with all the complaints regarding this part indicates manufacturing is producing a defective or inferior part. The service provided by Maytag, which is supposed to be a reputable company, is a joke and non-existing. Like many others, here I will gladly be part of the class action suit and will never buy another Maytag appliance and will also inform others of their poor service.

I bought this washer 2 years ago, it has always been noisy and not cleaned or rinsed my clothes very well. With dark clothes, I have to rinse them twice if not three times. Now it has quit throwing out the water all together and is not rinsing the clothes at all. Paid $72 for a repair man to hook it up to his computer and tell me there was nothing wrong with it. Told me it was how I was loading it. I dont think so. Now I have to replace a two-year old machine. I will buy a basic machine that only washes my clothes this time. Nothing is made to last these days.

I remodeled my kitchen, put in all new Maytag Almond appliances washer, dryer, stove, refrigerator, dishwasher and microwave oven. I was pleased with everything but the stove. The stove was $800.00. The oven caught fire three times and smoked up my house. I replaced the stove with another brand, cheaper and safer. I moved to a new house, five years later, bought all Maytag appliances stainless steel. The hinge on the deli tray broke, the inside is thin plastic, not covered in extended warranty. The stove caught fire (I didnt learn the first time around)! The microwave has a thin, bendable, plastic rack, the handle snapped right off. I cant buy a handle separate from the door. Now the microwave wont heat! My dishwasher was recalled. The heating element could have caused a fire! Nothing that breaks or malfunctions is covered by warranty. Who needs to pay for a warranty too and get no parts or service rendered! I will buy all new appliances and when I do, it wont be anything Maytag makes and none of their other brands! This stuff is very expensive garbage! Somebody please initiate a class action suit!

Have read others reviews and experiences and wish I had visited here first. Our first Maytag washer and dryer set lasted over 25 years with only minor repairs until the transmission started to leak grease and was uneconomical to repair. Our second set only lasted nearly 10 years and were obviously lesser quality. The wife decided that she wanted the best and high tech version. She really liked the features of the Bravos 300. What a mistake! Not even three years old and she has been dealing with the noise and the problem with constant unbalanced loads, intermittent error codes, odors and the forever cleaning requirement. The whites were intermittently getting rust stains until I determined that the underneath side of the top cover around the bleach reservoir had rusted out big time. I replaced the top cover for over $125 plus an afternoon that I will never get back. (Out of warranty, of course). Today the wife called me to say that the washer would not complete the rinse cycle and she could not reset it. We had to pump out the water and pick the wet clothes out. A grinding sound is coming from near the bottom of the machine and sounds expensive. The service man is scheduled to be here day after tomorrow to give me the bad news. My next washer purchase will NOT be a Maytag or any other high tech piece of crap. Simple is better.......

Was assured the washer could do comforters, etc. Well, I took a video of the washer doing 5 t-shirt, 1 pair of pants, and 3 pairs of socks on the power wash cycle. Nothing tumbled. All the plate did was swish some water around on the bottom. Clothes werent clean at all. Check my Youtube video, and you can watch the leg of the pair of pants sticking up out of the water and never getting back down in to get wet. Horrible horrible machine. With that said, called the company I bought it from, and they arranged for a front loader since Id only had the machine for a couple hours. Stuck me for a second delivery fee though, which I wasnt happy about. Well see when the new one gets here Tuesday.

This one of the worst purchases I have ever made! Paid over $850 in March, 2015 for the Maytag Bravos XL. At first, we experienced leaking and now there is a terrible banging and clanging noise! Had an appliance repairman come to see what was going on. Apparently it needs a hub replacement and bearing replacement. Was told by two companies that it is not cost effective to fix it due to the amount of parts and labor.Aside from this major issue, I never felt that the clothes came out clean. Many times, the clothes would come out with detergent all stuck to the clothes and had to be rewashed. The softener and bleach dispensers are not removable and it is nearly impossible to get all the way into the cup in order to clean the mildew that builds up. The fabric softener dispenser always had gummed up chunks.Called Maytag several times to no avail. Was basically told - too bad its out of warranty. I have never heard of a washer giving out after 3 years! The worst part is that I have searched many places on the Internet and apparently the bearing problem seems to be a common issue with this washer. I purposely bought an American made product and am extremely disappointed in not only this product, but the company as a whole. The customer service department is awful. I will NEVER purchase Maytag or Whirlpool ever again. They lost my business for putting a terrible product on the market and refusing to acknowledge flaws. Interesting that this model is now discontinued, but they refuse to acknowledge the problems. Stay away from Maytag and/or Whirlpool!

Maytag fridges, obsolete in less than 3 years. TWICE! My last Maytag fridge dies at about 2.5 years. I called up customer service. It was a compressor not repairable. This was an expensive fridge. Reluctantly we bought another one as the space could only accommodate a Maytag. Again less than 3 years old, the ice maker is shot and the plastic inserts are all falling apart. This time Ill renovate my kitchen for that extra 2 inches to accommodate a different brand.

I have had my washer and my dryer (model no. MGDB850WQ - serial no. MJ3311087), for 1 and 1/2 years. I have given both plenty of time and since the beginning, I have literally hated these products. This was a large purchase, so I feel locked into a terrible choice. I wish I had never bought these two items and will never use Maytag again. I will also never recommend these products to anyone. I do not like the new technology.

I love my Maytag washing machine. It have different settings for the wash, also a size load for your washing, and I love the rain cycle. You could do single runs with Downy or extra runs which is great. Especially great if you’re doing blankets and towels you need that extra rains. Great reliable machine. Highly recommended.

We bought our Maytag Bravo top loader on May 5, 2010. The machine was working fine. Then last week with no warning, the F51 error code popped up. We called Sears and they sent a repairman out. The result was the sensors work independently from each other (tested correct in the Ohms range). It made it through an entire diagnostic test, but will not complete a wash cycle. The repair guy concluded that the control board was bad. Estimated cost to fix was upwards of $400. I cannot afford to fix. Our issue with this product is that it is apparent, from reading all the forums, that this is a known issue. And we believe Maytag should be reimbursing consumers for this repair or they should recall the washer. Our washer is used on the weekends and it should have lasted us for minimally five years. All we wanted was to make it through one military overseas tour with it, not asking much. Instead, this machine lasted two years. Unacceptable.

Have a Maytag refrigerator, less than 2 years old. Water is leaking from top of the inside of the refrigerator, presumably related to water dispenser, unrelated to filter, and dispenser still functions. In shock, Ill have to pay an additional $347.00 to Maytag for an additional warranty if I want them to remedy this!!! Model # MFT2672AEM10. Buyer beware! Upset that such a new refrigerator would have problems - more upset that the company is making no efforts to make it right without charging more. The refrigerator was not cheap in first place. Also the time spent to have someone come out... Maytag advertises repairman boredom.... Never had another problem with other appliances unless they were much older!!!

After writing a polite but stern complaint to several of the executives at Maytag and Whirlpool we got a call from their executive assistant. She arranged to have a technician come out to our house and assess the installation. He found nothing wrong and Maytag replaced the control panel for free. The technician has seen numerous faulty electronic control panels, and not just with Maytag. He would not recommend a preferred make or model. He longed for the old mechanical timer switches, which we could no longer find in the newer models. With enough customer complaints maybe they will do something about the electronic control panel in the future.

I had purchased a brand new Maytag refrigerator and in less than a year, the ice dispenser stopped working. I had called Maytag warranty department in regards to this matter and they flat out said, There is nothing we can do about it. I will never deal with this company whatsoever and wouldnt recommend it to anyone about it. Less than a year and they refuse to fix the item they sold. No better than a used car lot attitude.

Purchased our Maytag Centennial Washer Model MVWC400XW4 2 years and 5 months ago; guess we are luckier than most; it has now failed in the spin cycle, high pitch, high volume whine, sounds like it is about to explode. Needless to say is out of warranty; and too expensive on our limited income to have a technician repair. I will hope to make the repairs myself; nothing to lose at this point; and from reading the countless negative reviews about this product; should be as many countless repair suggestions on YouTube. Obviously if Maytag would stand behind/up for their product as they claim they do; I and many others would not have these issues. My wife and I for sure will never buy another Maytag product until Maytag resolves the issue, which if my calculations are correct will be never. My advice is simple, do not buy Maytag products.

Problems with Maytag dishwasher, purchased at Sears Canada Model MDB7749S is only a couple of years old, and as such is no longer under warranty. This Dishwasher is less than 3 years old! Both the interior and exterior is stainless steel and looks virtually new. Cost of parts and labour to repair amount to more than a new dishwasher--this is unacceptable. Poor design. Little value compared to cost. First issue: bottom rack wheels fall off because the plastic pin holding the plastic wheels on the rack become fall out, leaving no way to hold the wheels onto the rack. Second issue: faulty design of the integrated door handle and control panel on the exterior door face. The control panel pops out of the front cover panel when door is pulled open. With some struggle it can be popped back in.I agree with another reviewer who wrote: The design of the faceplate is defective in that too much force is applied to the faceplate when opening the unit. The handle is integrated in to the faceplate. The plastic used becomes brittle over time and breaks. The panel unit (W10811169) must be replaced in entirety rather than just its housing increasing the cost of repair. To have this failure occur within the first 3 years of use is very premature. I can only assume if I repair the dishwasher I will have the same problem again. I am considering buying a new model that is designed better and comes with a longer warranty on such parts.

Disturbing that this product made it into production. I have the matching dryer too, and its just as bad. First the washer rolls up clothes into a tight ball better than I could do if I did it by hand. Then it spins, setting the wrinkles in thoroughly. Then, even though I shake out the clothes before putting in dryer, after the clothes come out of the dryer (without letting them sit in there) - the clothes look like someone drove over them with a car while they were rolled up in a ball. Bonus: the clothes dont even get dried. Ive watched the clothes in the dryer, the drum is designed so the clothes stick to the outside of it and go around, they never actually tumble or get any air circulation. What a disastrous product.

I have a Maytag Range that I bought new and installed 6-1/2 yrs ago for over $1200.00. I am single so I rarely use the ovens. The upper over I use maybe 1-2 times a month and the lower oven I may use once a month. The night of 3/7/2016, I used the cleaning cycle set on medium for both ovens. Yesterday, when I went to wipe the ovens down, I found the lower heating elements, on both ovens, had snapped. The top ovens lower bracket had broken in 2 places, the first break is about 2 from the connection, on the right side leaving about an 7 gap. The lower ovens element had broken in only one place about 2 from where it connects into the back of the oven. This has to be a flaw in the either the design or the material. In the 45 yrs that I have been using ovens and stoves, my last stove was over 35 yrs. old, I have never had a heating element break. While I can understand a break at the connection, I can see no reason that the it would break in the center of one side on both lower elements in the same oven. I also noticed that lower heating elements are a much small gauge than the top which I find strange.The other issue with the stove is the seals around the windows are not tight. I noticed dust was inside the two glass panes. The rubber seals were sunk down into the door, but Maytag said it was not their problem that I must have done something. When I remodeled my kitchen, I bought all Maytag products: 1.H20 Frig - The electronic panel went out after 3 months and had to be replaced. Manufacturing Defect - When the repairmen came to fix it, he told me to call Maytag which I did. They refused to pay for the repair because I called a repairman first, even though the business was Maytag certified. Even though I said I would cancel the service call they said because I had made the appt. and they recommended I call Maytag, they would not cover the repair. 2. Stainless Steel Dishwasher (Cost over $700.00) - Motor went out after 3 yrs. 3. Microwave/Convection Oven (above the stove)- Convection light out after 4 months. The replacements are not inexpensive.One other complaint I have is when I bought all my large kitchen appliance Maytag had a $600.00 rebate offer. Even though I mailed all the required documents to the company over 2 months before the rebate ended, I never received my rebate. The explanation I received was that the center that received my documents delayed forwarding them to the proper department that processed rebates and they were received after the offer ended. When I questioned the legality of the practice, I was told that this was all explained in the Terms and Conditions (ie: small print).

Maytag is supposed to be the best. I wanted a top loader again. This washer is almost worthless because of the water control. I have to add buckets of water before I start the washer. Otherwise the clothes are not clean. The cycles are strange with the amount of agitation. I will continue looking for an OLD model. DO NOT BUY THIS WASHER.

My washer is about one-year-old. Several months ago I noticed a brand new shirt was damaged after laundering. I thought it was inferior material. A couple of months later I saw a similar situation with another garment and started being more careful with the laundry settings using delicate, short, light washes, etc. The problem has happened a THIRD time to another garment. It appears this washer has a hunger for delicate jersey type fabrics. I started reading online and found out at it is indeed the action of the agitator and I need help rectifying the situation.

Our brand new Maytag front loader has a optimum (LOL) soap dispenser that can supposedly wash several loads before refilling. BUT, the dispenser fills with water after one load and dilutes whatever soap is left! We talked to a authorized tech who said it was a poor design. That the unit wasnt sealed from water or it would be under vacuum. We called Maytag and they said something like, Um well it has sensors!! Did they explain how it would sense the diluted soap concentration? Nope. It should be replaced by MAYTAG! Knowing it is something that they sell that is defective. Right out of the gate!! The engineer should be fired, the quality department heads fired too!

I would like to say that I purchased the Neptune washer & dryer for my parents back in 1998. Up to now, 23 May 2015, not once has either of the machines required service and have been functioning well for the past 17 years. This is a testament to the quality and workmanship that is Maytag. This week I have purchased the Maytag Maxima front loading washer & dryer for my home because of Maytags reputation.

I purchased the microwave less than two years ago. I noticed the display panel would not always work a few months ago. This is part of the control panel that shows time, etc. Called Maytag just now & they told me that the control panel is starting to fail. I could purchase a one year extended warranty for $289!!!Are you kidding me??? The part alone would be around $160. What has happened to Maytag? I thought they had a good name. :( Very disappointed.

I bought a Maytag Refrigerator (Model No. MFT2672AEM10; Serial No. K31503192) on 05/13/2013 at LOWES. On 07/27/2013 my son got hospitalized due to some kind of infection. He had fever and diarrhea that didnt go away. We didnt know what caused it. When my wife was cleaning the refrigerator, she noticed that the ice bin container had a rusty screw and metal plate. Why is the ice bin screw/metal plate rusting? We informed Maytag about this issue and they replaced the ice bin. Now, the replacement ice bin is rusty again. I sent an e-mail to the Maytag Customer Service Manager on 04/20/2015 and was told that its no longer covered by the warranty. I informed the manager that this is a defective/flawed design/rusting part from the beginning and Maytag should have REDESIGNED it when I informed them first hand and not just replaced it with the same defective/flawed/rusting part. I told the manager that this is a safety concern and Maytag needs to do something about it. The Customer Service Manager I talked to didnt want to do anything about it.

I bought a Maytag Bravos Quiet Series 300 washer just over two years ago from Home Depot. The control board and sensor went out last week. The service technician seemed rather surprised that a newer machine would have that kind of non-wear-and-tear problem and suggested that I contact Maytag/Whirlpool to see if they could help offset the parts costs, as the repair was going to cost over $600! The customer service agent I spoke with said that there was nothing they could do because the item did not have an extended warranty. I explained to her that we purchased this unit, even though it was out of our price range, because we were told that it would last a lifetime. I would have been happy if it would have just lasted 5 years! She was very detached and it was clear that Maytag/Whirlpool was not going to stand behind their product. I will now take the repair money and go buy a new washer. You can be sure that it absolutely will not have the Maytag/Whirlpool brand!

It has never failed me and I cant remember when we purchased it. When I grew up, my Mother only used Maytag Washer and Dryer. When I married (almost 50 years ago), I purchased a Maytag Washer and Dryer and have never regretted it.

Within 2 months of 1 year warranty running out, the control panel went wacky - does all kinds of weird things except work right. Called to see if there is any suggestions or work arounds and was told they would be glad to set up a service call for between $70 and $100, where they could tell me how much it would cost to fix. As with the other 100s of folks with the same problem, they basically said gee, you should have bought an extended warranty. If you have this many people with the same problem then it is Maytags problem, not the poor sucker consumer who got stuck with it. If you are considering this dishwasher, run, dont walk, as far from a Maytag or Westinghouse product as you can get. If anyone starts a class action suit against this product, please count us in!

Same complaint as most of the others: bought a refrigerator in 2013 and about one month after the 1 year warranty had run out the freezer started leaking water all over the floor and build up is on the bottom of the freezer, making it difficult to pull out the metal drawer. :( We do not have the water even hooked up to the automatic icemaker so have no clue where the water is coming from. Clothes washer has never worked properly from day one, didnt fill up with enough water. Had the repair man here while the warranty was still in effect and he verified that the washer DID not fill with enough water therefore leaving soap and grime on our clothes. :( He had to order an entire new brain and replaced it. Worked for a couple of months better than it ever DID and now back to soapy, grimy, dirty clothes again. Why isnt there a recall on the part that keeps backing up on these bottom freezer Maytag refrigerators? Someone needs to start a class action lawsuit and get these things recalled and replaced. Spent a lot of money on this brand new refrigerator and was so jazzed to get a brand new one for the first time in my life. :( Well that was surly short-lived. Shame on you Maytag, your company has really gone downhill. I would love it if an attorney could start a class action lawsuit with Maytag on their bottom freezers.

We bought our front load washer and dryer about 5 years ago and have had no problems with either. We also purchased a Maytag French door refrigerator 2 months ago to replace our Sears Elite brand when its compressor went out after 27 months (Ill never buy another Sears appliance).

Ive had my washer and dryer since 2007. We purchased a new vacation home and it was included. I used the HD washing machines at my daughters, though hers was a front loader from a different company. Im unhappy with mine. Would not purchase one again. I find my clothes arent clean and my kitchen clothes and towels always have a residue on them. I now wash everything on warm, use the proper amount of soap and have to do heavy load cycle. Im still not happy, but it beats buying a new one.

We bought a Maytag refrigerator around 2 yrs ago. Ive had repair out a couple and tried to take care of this myself. I am being told by repair men that it is a design flaw that the line gets plugged and water pours out all over my floor. The refrigerator I replaced was 20 yrs old, never had a service call & never poured water all over my floor. From reviews Im reading Im not alone in this problem. Needless to say Im less than happy with Maytag at this point! Model #:MBF1953YEB3, SER. #:K22812455, reciept #:** pd 1/19/13 DECKER & SONS 430 FULLER GRAND RAPIDS MI.

I purchased a new Maytag range (gas) in June of 2012 - 6 months ago. I have had the same problem many others have had (as Ive just read) with the toxic smell every time I used the oven. I was told it was just the chemical burning off from being new. I have never owned a new oven so I took their word for it. On Christmas day, my kids and I were going to bake cookies and set the oven to preheat. Flames and black smoke were shooting out of the range, and the fire department was called. Even after the fire department put out the fire and removed the stove from my kitchen to my front porch, they spent more time investigating the situation to make sure my home was safe than the certified Maytag repair person that was dispatched out by Maytag to service the range. This stove is only 6 months old and still under warranty with Maytag. The service person they sent out did not take the stove apart and spent less than 5 minutes looking it over; then he determined that it was a grease fire caused by owner’s negligence. I disagreed with him and told him I have been cooking for many years and thought he did not do a thorough job to determine the problem with the range. He got very upset with me, took his bag and left without leaving me a service slip. I asked Maytag to send someone else out and explained to them that this service person did not do a sufficient job in examining the range, nor did he perform any kind of service to get the range back in working condition. Maytag claims they will not send anyone else out, and there is nothing more they will do for me. They say it is my fault it caught fire; and if I want it fixed, I have to pay for it myself even though it is still under warranty with them. My stove is still on my porch where it has been since Christmas day. I then visited Maytags Facebook page and corresponded with others whom have had similar issues with their products and the lack of customer service from this company. Maytag has now blocked me from commenting on their Facebook page. The customer service rep on that site asked me to email her all my information about the range and my issues with it, and she assured me she would respond to the matter. As of yet, I have heard nothing back. I am terribly dismayed by the way I have been treated by this company, their so-called certified service technician, and that they do not honor their warranties or stand by their products. I am cooking for a family of 5 in a 12-year-old microwave (which is not a Maytag by the way) after spending over $600.00 on a brand new range.

This will be the third repair of this refrigerator in one year, the same issue of the refrigerator warming up. Water all over the floor due to ice thaw. Also food spoilage. I want another refrigerator at this point. The Maytag repairman is definitely not lonely. He has more business than he can handle with this defective refrigerator. Terrible. Do Not Buy!!

I purchased a Maytag Bravos 5 months ago. I had trouble at first with unbalanced loads. The repair man came to look at it twice. One thing that can unbalance your loads is if small pieces of laundry such as a sock gets outside the basket. Sometimes the basket has to be taken all the way out because small pieces can be lodged under the basket. This happens when you fill the machine too full and those small pieces float to the top.The suspension on my machine ended up needing to be replaced. I have read lots of reviews about soap rings in the clothes. That happens from using too much soap. Make sure you are using HE detergent for one. I cut way back on my soap and my laundry gets clean and no problems with residual soap on my clothes. I was very unhappy with my machine at first but now I absolutely love it!

I purchased a Maytag dishwasher at Home Depot in Roanoke, TX on 07-14-2011. Model Number: MDB7749AWB2Serial Number: F12604431Unfortunately, Ive just been obliged to open my third service call on this new dishwasher. The first service call was made in August 2012, just outside of the first year warranty period to repair a wire which had come loose in the control panel, making the dishwasher inoperable. The second service call (May 2013) was to replace the front panel housing and touch pad which had broken off at the screw-mounts holding it on to the door. As the handle to open the dishwasher is part of the front panel (which must be pulled out pretty hard to open as it does not have a latching mechanism) screws set into unreinforced, thin, plastic posts holding the panel to the door seems like a serious design flaw.The third service call which I placed last week (August 2013) is to address the fact that the dishwasher has become completely inoperable with no lights on the front panel and is completely unresponsive. To say the least my experience with this product (and by extension the Maytag brand) has been a serious disappointment. I guess the reason I no longer see those TV commercials with the lonely Maytag repairman is because these days hes actually really busy fixing broken down ** Maytags. I will never, ever buy any Maytag or Maytag-family brand appliance ever again.

We like the refrigerator and we have had it several years. But the thing the top freezer conceals much of the top rack of refrigerator. We must duck and almost kneel to get to food inside. Next fridge will have drawers and doors that open on both sides.

We bought the Maytag set of dryer and washer just over 5 years ago with ex. war. The dryer now doesnt heat up but the drum does turn. To fix it would cost about $500 maybe more and the parts may only last a few months. I believe that dryer should last longer when only used about once a week. I am now looking at Speed Queen. Cost more but am told they last longer.

I purchased My Maytag Washer and Dryer set from Lowe's, which was a very good experience all the way, back in June 2017. After two years I can finally give an honest review. We love this set even though it is not as quiet as the old Maytag washers. Still is but not as. We have not had one bit of trouble from either the washer or dryer. The next size larger would have been the better choice for us since we now have king size bedspreads to wash. It still does the job though, just one piece at a time. A lot of people complain about the smaller amount of water used but it still cleans clothes quite well. If you need more water just use deep water wash or for even more water use the setting for bulky sheets which really fills up the water level.

The refrigerator is barely over two years old and the bottom pan fills with water, freezes and leaks out onto floor. Is a very common problem with these refrigerators and Maytag is happy to pay for the new part to fix it, but will not pay for any person to fix it. They have known this is a problem for a while, but will do nothing to fix it. They clearly do not stand behind their product with a known ongoing problem. The Maytag repairman is no longer not busy. Will never buy a Maytag appliance again! Will take the new part and fix it ourselves.

Maytag front loader 5000 series error codes - After using my washing machine for 3.5 years, under light duty, I have an error code of SUD and F35 indicating that the pressure switch has failed and needs replacement. I will need to buy a new pressure switch out of pocket and replace.

I have never had washing machine that caused this many headaches. The point of a machine is to save you time and energy washing by hand. When the cycle is over, the clothes are tightly spun together that we spend half an hour attempting to untie all the clothes that are woven together. The clothes come back to us in knots, or torn because of the rough nature this machine has created. I have never seen anything like this before and would gladly throw this piece of junk out. We are moving and it would create more headaches to deal with this at the moment. I read that the company had severe money problems and it was due to this very issue. I cant believe a company this well known would allow this to ever hit the market! To openly LIE to people and make money off a product that is faulty deserves the karma they get. Please stay away from this company and their rubbish machines they make and then sell. BUYER BEWARE!

My dishwasher is one year old. It is very quiet and cleans well. Stainless steel makes it look great too. Efficient, energy saver dishwasher with great capacity and large utensil holder. This is the best dishwasher I have owned.

I purchased a Maytag Bravos line washer model # mvwx500xwo back in Oct. of 2010 thinking that it would be great to save money on the water bill. I first had issues with it putting holes in my clothes. I then found out if you do not zip up all zippers and button all buttons, the machine will rip them up due to the high speed spin cycles. Now, the washer will not fill with water or start the wash cycle. I mean really, its less than two years old and I have to shell two hundred plus dollars to fix a washer that only cost $500. I guess I know what brand not to shop for next.

Purchased this washer at the end of August and it was delivered the first week of September. On September 27th the rubber seal around the door somehow got tangled in with a shirt and was ripped off (absolutely no idea how that even could have happened) and spilled water all over the floor. I called Maytag on Sept 27 and they had a tech out here by October 2nd which was great. However, even though I had told them the problem and that the rubber seal was damaged the tech didnt bring one when he came. I had to call them last week to find out what was going on - they had the tech call me and he said that the part had just shipped and he should have it by next week - Today, I had to call again as there was no follow-up from the tech and was told that hopefully the tech will come on October 21st once he gets the part as he hasnt received it yet. I regret purchasing Maytag, as I had heard they had better service (local techs/parts warehouses) than LG or Samsung but that doesnt appear to be the case. 3 Weeks to repair a $1400 washer that I used for about 4 weeks is unacceptable. On top of the inconvenience Ive had to spend $40+ dollars a week at a laundry mat, plus waste my time. One star service.

All my kitchen appliances are from Maytag, however I would highly recommend buying the extended warranty for any appliance you buy. Maytag is not helpful to customers when it comes to repairs. They will recommend you their authorized companies which here in Colorado Springs are the one with the worse review and already knowing the the repair will cost more than the cost of a new one. You will have to be available 5 hours of your day and spend $110 for a guy to come to your house and tell you that the repair will cost more than a new one. Oh and if your microwave is a 2.0 CU like mine you will have to pay $300 plus in double labor because your microwave will require two people to take it down from the kitchen cabinet.

Maytag French door Bottom Mount Model # MFT2976AEW02 - Purchased this model refrigerator in late 2013. Had minor problems with ice maker for last 6 months, not have freezer problems, as the bottom freezer is not keeping food frozen. Called repairman today. He ran 64 checks on refrigerator, said to keep eye on problem and he will re check in 24 hours. Called private company, Maytag in Latrobe. They referred us to the Maytag repairman. We will keep you posted. We moved all of our frozen food to a downstairs older freezer for safekeeping. Keep checking, we will update.

Has anyone talked to an attorney to see if a class action can be filed? My fridge is leaking, sheets of ice on floor of freezer, and ice maker doesn’t work. Looks like it’s the norm for these. Please post if you have spoken with an attorney. If no one has, I am going to.

We had this washer 16 months. We bought it new from Home Depot. The clothes came out with spots on them, white residue and grease spots. This was ongoing for awhile. The bearings went out after 6 months. It was so loud now the water pump went out. I was told by Whirlpool (they bought out Maytag) that water pump is on back order and could take a couple of months!! To fix the bearings and the water pump was almost 700.00. A new washer is 1000.00. We junked it and had to buy a new washer GE. We are sick about this waste of money!!! What a piece of JUNK this Maytag Bravos XL is!! We need to have a class action suit and try to get something back. This is ridiculous and they arent taking responsibility. Whirlpool/Maytag are rip offs!!!!

We have had 2 Maytag dishwashers only last less than 2 years. Since we can only have a portable because of owning an older home the expense is too much anymore. We also had a Maytag Neptune clothes washer last only 2 1/2 years. We had always respected Maytag and trusted them. That trust is gone. It is too expensive to buy and lose them after barely 1 1/2 years. We had a Kenmore that lasted 23 years. I dont know what company to trust anymore. The one we just had quit working a month ago was purchased October 3013. Maytag dishwasher Model #MCD4809PAW2 Serial #F34003436.

I bought a Maytag Range with the Aqualift feature 3 years ago. Worse purchase every, the oven clean option (Aqualift) is useless. It do not work at all, be prepared to spend hours cleaning. I followed manufacturers instructions and its useless, after running the cleaning cycle three times I gave up and starting cleaning for hours.