I related my problems with a Maytag Bravos Washer a few days ago. A year and a half after I purchased the washer, it would no longer spin, among other problems. I was persuaded to call a repairman who diagnosed faulty electronic components which would cost me nearly $400 to repair. He confirmed that the washer was poorly built and strongly advised that I replace it. So, after paying him only $25 for a service call (he felt sorry for me), I did some research and bought a top-load agitator washer because the old-fashioned machines actually do their job - they wash clothes! I was duped by the high-efficiency claims, low-water-usage of the Maytag which didnt wash that well when it did work.

Turned the oven on, and it failed to light. A little while later, it started leaking gas into the house. Im lucky the house didnt explode!

I have always loved Maytag but this top load washer is a bust. I purchased this higher dollar energy efficient washing machine to hopefully get the value out of it for years to come. Model MVWC565F. 4.2 Cu Ft. I use good quality liquid laundry detergent. I launder adult clothing (including business casual wear), sheets, towels and pet blankets. Occasionally the 20+ something children do their laundry while home. I often have dry spots on my clothes where they never got actually wet. I switched to only using the deep water cycle; however, this does not immerse the load in water. The smaller my load the less likely to get clean. Ive adapted to only have large loads but I still do not feel my clothes are getting clean. I often have to run the load a second time to not only remove ordinary day-of-wearing smells (very noticeable in socks for example) but to get them all wet and free of soapy/linty-like spots left on the clothes from the washer (most notable on black leggings, dress pants, etc). I always do my towels and bedding separate from daily clothing, so this is not coming from having a mixed load. I have also noticed that the load takes much longer (up to 2 hours) for my washing cycle. How is this energy efficient? It uses less water but more electricity? I miss my old fully-immerse-in-water washing machine that washed in under an hour! Love the dry that I bought with this but not the washing machine!! I do not recommend this washing machine!!

Im writing in reference to Model # MF12569YEM2. Bought this 3 years ago for close to 3k. Since then it forms a sheet of ice under the bottom freezer and leaks water onto the floor. It has ruined my hardwood floor and leaked through the floor to my basement and now need to re-sheetrock the ceiling. Its a bad design and should have been recalled because I see everyone else with this model is having the same issue.

Our Maytag Atlantis dryer had smoke coming out and almost had our house on fire! Had it not for us double checking the entire house would have burnt down! The dryer is less than 10 years old and already it is tearing apart. I cant risk using it again. Terrible company. I would never buy Maytag products ever again!

I had the exact same experience as the Tampa person with my Maytag dishwasher (Model: MDBTT60AWW). It was not cleaning the dishes, even when I thoroughly rinsed them. Plus, it started leaking midway through the cycle. Since the warranty was expired, I purchased an extended warranty in July 2012 for $296 (yes, in hindsight, I should have just bought a new appliance, not Maytag). I had 3 visits from 2 different technicians, both telling me the dishwasher did not leak. One telling me I was using the wrong kind of detergent and thats why dishes werent getting cleaned. The other telling me that there were too much suds and that could cause it to leak. So, I should pour a tablespoon of cooking oil (yes, cooking oil) in the dishwasher when it starts leaking and that will cut down the suds. I dont think so!Then, I found out a couple of weeks ago that this model was under a recall since 2010, not related to the leak at all. Yet, Maytag still sold me the extended warranty (wheres the ethics of that?). I requested a pro-rated refund of the balance on the warranty - and wouldnt you know that with the technicians service calls, the amount of time used on the warranty (6 months) plus an admin fee - I have used $296.48 of the warranty amount. It is almost to the exact penny of what I originally paid, so I will not be receiving any refund. They are only giving me a debit card of $150 or $250 once I buy a new Maytag to replace the recalled model. I do not want to continue down this frustrating path known as Maytag appliances.

After having issues with bearings in a front load of another brand, we decided upon a top load Maytag. We have had it less than a year and we are not happy with the performance. We are using more detergent because the dispenser seems to be bottomless. Only the front of the little pull out drawer is visible and it never seems to reach the fill line when adding liquid detergent. There is no quick wash cycle. Not everything needs a cycle of nearly an hour or more. The spin cycle does not remove nearly as much dampness/water as our previous frontload. The drum is deep making it difficult to retrieve small items such as socks. My biggest disappointment is finding lint residue on the clothing and it remains even after an extra rinse. This is especially visible on dark clothing. Even the lint filter in our dryer fills up much more quickly than before. After researching, I found that others complained of this same problem.

Maytag Bravos 300 Electric Dryer - Purchased dryer 2011 and a computer part went out and Maytag wants $418.66 for a computer part. This dryer was used only 6 months a year. Poor attitude about repairing from Maytag and they would not do anything to make us happy with product. A dryer that goes out in 3 years is robbery. Maytag should repair and make customers happy but they just dont care. Anyone who buys a Maytag or Whirlpool product should have their heads examined. I tried to talk sense to Maytag representative but to no avail. I am now going to make sure all of southern Indiana knows of my problem with this product. Those who know me know I have the ability to contact thousands of southern Indiana and Louisville residents.

The Maytag Bravos XL low water washing machine is very disappointing. About 20% of the time it needs a second rinse because there isnt enough water released to rinse clothing. Forget washing anything large. It just doesnt do it. Waste of money. The matching dryer is just fine - no complaints.

I have had my washer and dryer for about 5 years. After a couple of years, I noticed my washer would fill and stop. When I go to put clothes in the dryer, it’s still filled with water... very inconvenient! I have to open and close it and then it continues. The dial doesnt work properly! The delicate cycle hardly works... that started after about a year. It just freezes up and stops. I have to open and close it. It does not rinse right, leaves a film on dark clothes, and I have to rinse again; I do not over fill it either. Sometimes it does smell a little mildew.The dryer knob does not work properly. I set my setting and pull the knob out, and it doesnt come on. I have to do it several times or change the setting or put it on 30 minutes only... very frustrating! I never had these problems with my Kenmores! I wish I did not switch brands. These things should work properly. I realize washers and dryers dont last like they used to, but come on! They also cost so much more than they used to. I wont do this again. I will do more research as to what is a good product. Too bad!

After less than two years the commercial washer we purchased from Lowe’s died. A repairman came out after a week and said it potentially needs a new control unit or computer. The control unit is on back order and we’ve been without a washer for a total of three weeks. The situation still remains unresolved and I’m regretting not going back to Samsung. After 9 years with a Samsung washer, it died and Samsung refunded the full price of the washer. It was a poor choice to choose American. :(

Maytag AquaLift Oven #YMER8880BW - The aqualift technology does not clean the oven. It is sorely inadequate. I bought Maytag because of its reputation. This range should be recalled as should all their ranges with this useless technology. Buyers BEWARE! Do not purchase any range from Maytag which advertises Aqua Lift technology. This purchase has soured your reputation Maytag. I also purchased a fridge with the stove. I will NEVER buy a Maytag product again. I also would like to ask frustrated and disenchanted readers how they are getting their ovens cleaned. What product(s) can be used. Maytag - complete FAIL!!

We bought a New Condo, all New Maytag appliances with a 10 yr. warranty, the microwave is a built-in model. I cant believe weve only been here a year and eight months and it just stop working. We use it for heating and short timed cooking like 1 to 2 minutes. I would think a name brand product would last a lot longer than this. I had an off brand microwave for five years before the condo. A couple of times the microwave door didnt close, I thought I forgot to close it. But after reading your reviews I now realize its one of the defects of the product. I called the Maytag company, they informed me that if a serviceman come out to fix it, it will cost me $180 until they can determine if the cause is something covered by their warranty??? The Home Builders bought Maytag junk and passed us the cost, now Maytag wants me to pay to see if their junk can be fixed??? Wow!!! This is unbelievable!

I bought a Maytag Neptune top load washer in 2002. It worked fine (with the exception of smelly clothes) until October 2011. Since then I tried replacing two new clutch assemblies, a new outer tub and bearings. What we were just told this week: it needs a new spinner. Finally throwing in the towel and taking the $500 credit from Sears and buying a new washer. And I can guarantee I will never buy another Maytag product again!

We bought a Maytag Bravo washer and after less than 6 months of use, it stopped working with an F51 or 53 error (cant remember which because its been a month now). After looking online, it seems that almost everyone who buys this gets this error and has to have a part replaced! And Whirlpool hasnt recalled the faulty part even though everything Ive read says it should be a recall.Its now taken over a month to get a repair person in to fix it. From the time we called Maytag, to the referral to the service person, to the service appointment, to waiting over 2 weeks for the part to come in, its been over a month with no washer. This is unacceptable Maytag! The repair company is finally showing up tomorrow only after 3 left messages from us.Either build a better washer or stock your replacement parts with the local repair companies and you should be reimbursing your customers whove spent a lot of money at the laundromat after spending between $700 and $900 on your washing machines.

Prior to purchase, I did my due diligence and read reviews about this washing machine. Apparently, they were written by Maytag employees, because this washing machine has been a major disappointment. Yes, it tangles clothes and sheets, but I feel that is to be expected since it is HE and uses less water. I will give it that and I dont have to dry nearly as long. But that is where my positivity ends. Clothes dont always come out totally clean. And then there is the issue with the horrific grinding noise. The machine has been making a progressively louder, angry, grinding noise with a high-pitch end note. And as of today, a horn type noise has started. Lovely.I anticipate the machine is on its last legs and I have only had it a few years. I spent too much money on this and feel like I have been misguided and, quite honestly, ripped off by Maytag.

I purchased a Maytag washer and dryer three years ago. They both were taken to recycling and I received eleven dollars for both of them. They were both horrible. The transmission went out on the washer. The repairman said not worth fixing since it would cost $600.00 to repair. He said Maytag appliances are being outsourced and are not what they used to be. Even before the transmission went out it took forever to wash and the clothes smelled when I took them out of the washer. The dryer quit heating a few days after the washer went out. The repairman said it wouldnt be worth repairing it either. I will never buy another Maytag!!

Purchased a Maytag washer and dryer 6 years ago and everything was fine until 3 weeks ago when the washer stopped spinning. We knew we were out of the 1 year warranty and contacted a repair service, who told us the bearing was no good. Contacted Maytag who offered in goodwill to pay for the parts and we would pay for the labor. A different repair person came in and told us the washer has no bearings but a transmission, which went bad. They ordered the transmission and today the repair person was in to install it. He installed the transmission, but while trying to take out the old one he dented the drum. According to my husband the repair person banged so hard that it sounded as if something could have been damaged, sure enough it was the drum. Contacted Maytag to see if anything can be done as now we still have no washer, and the repair person was their selection not ours. All we got from Maytag was they are not responsible and there is not much more they can do. I cannot believe the last Maytag product we had lasted over 20 years and this one is less than 6 years with problems. Will not purchase another of their products again.

When we first purchased our fridge, I was super excited. I have read the numerous reviews regarding ice in the bottom and the noise. Ours is noisy also. Nothing I cant live with. Now ice on the bottom. That doesnt work for me. A friend of ours told us the drain was plugged. Not that the doors needed to be replaced, nor does it need gaskets. All you need is a hair dryer and a man like mine who can build or fix anything (honest to God that is the truth). He took the drawers out and then removed the door to the freezer. In the center on the back of the fridge is a drain hole. Aim a hair dryer in this spot and it will melt the ice which is plugging the drain. Ours took about three years to have the water in the bottom issue. Since we have now seen where the drain hole is, there would be no need to take the door off and the drawers out. Now, one other preventive measure. Take off the lower back plate of the fridge. At the beginning of the drain hose is a rubber nipple. There is barely any room for the water to drain. We cut the end of the nipple off in order to make the water drain better and less likely to stop up. We just snipped a bit of the end. The reason it is designed like that is to prevent air from coming into the. Just a small snip. I hope this may help some of you. Tell the Maytag repairmen how to fix it.

I purchased my first Maytag dishwasher and it was recalled as being a fire hazard. I was offered to have it repaired or pay for an upgrade (approximately $200). I chose to pay and upgrade because I dont want a fire hazard in my home. After my paid replacement, I received a recall on the new dishwasher regarding the same issue (different model) and I chose once again to pay and upgrade (thinking that if I spent $700, I wouldnt have a problem). In less than two months of installation, the dishwasher died in the middle of a cycle. Filled with water, I bailed it out and called Maytag. I told them that I wanted a new one and they told me that I was past the replacement period. They sent a service man out and he stated that it was a problem with model # MDB7709AWB2 and serial # F03002958. He said that it was easy to fix and said he had done it several times. So now, within less than 1 month before my warranty is expired, the dishwasher did the same thing--it died in the middle of the cycle and wont turn on. I called Maytag and they told me that they would send out a third party repair company (JD Appliance) but I would have to wait for four days. I contacted Maytag and said that I was concerned about the dishwasher breaking down again for the same problem (bi metal unit blew). This is the second time it happened. Jeremy, the repair man, said that the first replacement was not installed properly and they should have replaced the entire unit. He stated that it was a common problem with that model, as did the first repairman in Dec 2010. When I spoke to a supervisor named Kia at 800-344-1274, she stated that they had no known issues with this model. I said that it was not what the repairman told me as well as the Maytag dispatcher. They both said that the heat sensor (Bi Metal Thermal Unit Part No. W10258275) goes up and has to be replaced because it is overly sensitive. If you are out of warranty, it costs around $200 to have it fixed. I told Kia and she said that it was not documented in her file, therefore, it never happened. I want to know my consumer rights to address this issue. I have paid for (on 3 occasions) a new dishwasher and have continuous issues that cost me money. I want an assurance like an extended warranty, free of charge, for the dishwasher that has already been repaired twice for the same exact problem. I have the original part that was improperly replaced to prove that it wasnt replaced to specifications, therefore, blowing it again. I was told by Kia that Maytag does not compensate or replace their products unless deemed not repairable by the technician. It doesnt matter how many time the same problem occurs. I would appreciate your attention to this matter.

I bought a full kitchen of Maytag appliances when I bought a new house in 2009. I thought it was a reliable company. Id always gone with GE before. I couldnt get the packing sticker off the oven after trying everything to remove it, so the oven bottom is virtually ruined. The timer on the oven dings once and stops; dinner burns if Im not right there to hear it. I was told by customer service thats the way it works, so I had to buy a separate timer. I am now replacing my 2 ½-year-old dishwasher because the control panel has once again stopped working. It cost me $275 to fix the first time and it lasted less than 3 months. I will never buy Maytag again! I got over 20 years of service from my GE appliances.

I purchased a new washer and dryer from Lowes a few months ago. I had my former washer and dryer for nearly 20 years and although the dryer started to have some issues, the washer worked wonderfully. To have a matching set, I decided to purchase both a new washer and dryer. I was told the Maytag Bravos XL model was the top of the line and could handle large loads. After just a few washes I realized this machine does not add enough water to get the top clothes wet and there is no agitator to pull the clothes into the water. I returned to Lowes and was told to use the deep water wash. I tried that and still had clothes coming out from the wash still dry and dirty. Unfortunately Lowes would not take the machines back and I was told to call Maytag. Maytag said there was nothing they could do except send out a technician for a service fee of $98 to help me determine if the machine is functioning correctly. I could not dislike a washer and dryer more! The dryer catches clothes on one of the screws inside and pulls fabric pieces out. This is in my opinion the worst washer dryer set I could imagine having. I will share my experience with as many people as I can to help others avoid making the costly mistake of purchasing a Maytag product. Maytag does not seem to care they have designed and sold a dysfunctional product!

This machine was purchased two years ago at the Home Depot. I wanted a top loader that was not digital and without a lot of choices. It has been nothing but a headache with every wash. I had a Maytag serviceman come out immediately and he said nothing was wrong. Every wash load I do, has problems. The dark loads are always full of white spots and the towels are torn up. Just bought some new towels and after the first wash, they were ruined. I will never ever buy a Maytag machine. These new He machines are ridiculous! I no longer have a receipt, but the complaint should help consumers in their decision to NOT buy a Maytag machine.

I purchased Maytag dishwasher (model # MDBH979AWW3) in June of 2010. Trouble started on washer after 18 months. Touch pad buttons dont all seem to be working. Occasionally gets to run after slamming door multiple times, but dispenser doesnt function properly. After trying to diagnose myself with door switches, connectors, etc., I caved in and called service. Service quoted $470 parts and labor to fix the problems, including control touch panel, dispenser, and control board (seems common from what I read here). Wish I had seen this string of posts before I called Maytag/Whirlpool customer service to see if they would help before I did any repairs. The responses I got from the service rep were rigid and scripted. Only time she varied from the script was to explain that modern high-efficiency appliances dont tend to last as long as ones 20 years ago. 18 months? Really? I might buy that if it was a mechanical durability design issue. Supervisors responses were also scripted, pointing back to the 12-month warranty. She said she did a warranty search on my model and that there was no warranty concern for this problem (really?). If there was, she might be able to help me. I guess there is no warranty history because most failures are between 12-24 months and the consumer has to pay for replacement outside of warranty. No semblance of customer service or customer care, just repeating what is on their website. Response was: I am sorry you are dissatisfied with the product and my response, but there is nothing I am authorized do. Sent an email to Maytag customer service regarding the problem and customer service interaction. They called back saying they stand by the original customer reps response, but offered to have someone else come out to give a second opinion on the problem. From what I read here, that doesnt seem necessary. Wish Maytag/Whirlpool would at least acknowledge that there is a problem, even the auto industry seems to have figured out a way to equip the service industry with known recurring problem history (TSB) and offer token help to keep customer loyalty. Apparently another quality organization fallen victim to short-sighted methods of maintaining shareholder value.

Model MDB4949SDZ0. 7/10/2018 Purchased from Costco. 7/23/2018 Installed by company arranged by Costco. 6/18/2019 A burning smell was coming from front control panel area of dishwasher when it was turned on. 6/25/2019 & 7/3/2019 Repair technician came to fix but could not find anything wrong so burning smell continued whenever dishwasher was one hour into cycle. 7/12/2019 Repair tech changed out front control panel because burning smell was still coming from handle area. 8/9/2019 Dishwasher does not drain completely when wash cycle is complete. Sometimes there is sudsy water left, sometimes it is clear. The water level is above the heating element at bottom of dishwasher.We only run the machine 2-3 times a week and have been using different cycles to see if the draining issue is with one cycle or all of them. No matter which cycle is used, water remains at the bottom of the dishwasher above the heating element. This seems like way too much residual water. Repair technician is scheduled to come for the 4th time to look at dishwasher but we just received a message that we will have to pay $129 service fee because dishwasher is now out of warranty. Maytag, fool me once, shame on you. Fool me twice, shame on me. Therefore, know that we will not be purchasing a Maytag product ever again.

2 years ago I purchased a Maytag Washer & Gas Dryer. Unfortunately, I did not invest or believe in extended warranties. I believe in trying to buy quality products. The door on the washer would not open and 2 error codes were displayed. I was trying to add another piece of laundry and the washer had just started. I canceled the load, waited for the door lock light to go out, but the door would not open. The error codes began displaying E3 and F5. I immediately went to the Maytag website for a resolution. The suggestions did not work and was instructed to obtain service if they did not. I called for a service call for $35, but was told that the repair would be over $300 for parts and that was not including labor. The parts I needed were a control panel and a part for the door lock. This was not a Maytag Company service tech and he told me that this happens because the parts are plastic. Currently, besides a Maytag Washer & Dryer I have a microwave, stove, and dishwasher that are also Maytag. When I replace these appliances, I WILL NEVER BUY ANOTHER MAYTAG PRODUCT. I expect the quality and life of an appliance to be more than 2 years, without buying an extended warranty. When I told a friend what had happened with my Maytag Washer, she told me that she had a Maytag Washer broke down with a control panel problem, and she couldnt remember the other part. She informed me that her repair was over $500.

I purchased the matching Bravos Washer and Dryer in April 2010 at Lowes. I also purchased the extended warranty to have coverage for 4 years after purchase date. I noticed the dryer sensor is not very accurate. The purpose of the sensor is to detect when clothes are dry and then end the drying cycle automatically. However, it fails in both ways. When the dryer stops on its own, the clothes are still damp. I have the setting on NORMAL>LOW HEAT>NORMAL DRYNESS (the reason for the low heat is not to fade/shrink clothes) and even though the heat is on low, it should still keep running until the clothes are dry. So when I open the door and feel the clothes, they are still damp; I turn it back on to run again. If I dont check on it every 10 minutes, the dryer just keeps running and the clothes are bone dry. The sensor should detect this. Once, I decided to test it to see how long it would run with dry clothes and it ran for an HOUR before it shut off. Talk about a waste of electricity.The washer also has issues. First is the SHEETS setting. This setting is supposed to prevent sheets from tangling/balling up. Every time I use the sheets setting, my washer stops with the UL error - uneven load. Meaning, I have to babysit the washer because otherwise, it will stop and wait until I pull out the sheets and loosen them up. I am only washing 1 fitted full size sheet, 2 flat full size sheets, and 4 pillow cases. The reason I bought this machine was because it is supposed to handle king size bedding. Apparently, this washer cannot even handle full size bedding and I refuse to wash each item individually - the machine is supposed to save energy, not require extra loads. The second issue I am having, which resulted in me calling to utilize my extended warranty, is tiny rust dots on my clothes! About 3 months ago, I noticed one of my t-shirts had 4 tan spots smaller than the size of a dime. I assumed I spilled something on myself. About a month later, I noticed it was on another top. Then I assumed it was something on the back of my chair at work causing the spots. It seems to happen every couple of weeks because another article of clothing had these mysterious dots on them. Once, it appeared on my towels and sheets. I realized it was not me spilling anything on myself, nor was it from anything on my chairs. Now, I wasnt sure whether it was the washer or dryer, but I noticed when I pulled out a white sweater from the washer, there were 3 dots on it in the front, and I definitely would have noticed these before, which is how I came to the conclusion it’s from the washer. I cannot see any rust inside of the washer basket so I dont know where its coming from, but I am certain it is not from other articles of clothing (such as zippers or snaps); and the reason I know this is because I do not wash towels with clothes and also, I am 8 months pregnant and have been wearing maternity clothes for the past 5 months and they do NOT contain any zippers or snaps. I took pictures of the rust stains on various items and combined to 1 image. Now, I called my extended warranty to have a service technician come assess these three problems. Well see what happens.

Would give them 0 Stars if that was an option. Bought a Maytag washer and dryer in Aug 2021. Washer broke Jan 6 2022. Called Maytag/Whirlpool on Jan 6 as it was still under warranty. They only had one service company in our area to work on the washer. I called them and it took them 10 days to come see what is wrong. Ordered parts. Said it would be 2 weeks. We are now 6 weeks into this with no parts. Called customer service and they said they were notified that their service company needed a part and would take another 21 days to resolve. Talked to a supervisor (Demetrius) who sounded like he did NOT want to be in that position. Offered no solution other than we will just have to wait. Threw a 3 month extension for the warranty on which still does not fix the problem. Sad to see this company go down the tubes as it was once a pretty decent business with solid products. No longer.

We have a bottom freezer Maytag refrigerator and after 2 years normal use it started leaking water onto the floor every day. After researching this problem I see that it is a widespread issue originating from an engineering mistake. I spent a weekend afternoon taking apart the freezer, clearing the frozen drain line, and putting it all back together. Im assuming this will keep happening every so often since it is a Design Flaw! Do yourself a favor and avoid Maytag!

Bought Maytag Dishwasher in 2/2012. 10/2015 dishwasher stopped working. My husband tried to replace the motherboard, however, dishwasher completely done. Called Maytag and they said they would send a repair company at their expense, however, repair service called to verify appointment and told us how much it would cost us! Maytag had no intention of paying the bill even after they said they would. Called Maytag back and said the other customer service person was incorrect. Now, buying another dishwasher only after 3.5 years.

My refrigerator outer case has felt very warm to the touch at the section between the top freezer door and the lower refrigerator door for several years. I thought this was a normal function of the defrost mode. It is now very hot to the touch so that I cannot touch it for more than a few seconds. I dont know how long it has been like this. This cannot be normal. I did some online checks and found that there was a Consumer Product Safety Commission Recall release #09-145 and 09-322 that warns about the same problem I am having. My model # (MTB215) matches the recall, however, the last two characters in my serial # is WQ does not. This problem appears to be very consistent with the problem in the recall releases.

We bought a new Maytag dishwasher MDB7609 as part of the 2010 recall. Within the first twelve months the black skirt at the bottom of the door collapsed to the floor. It was in small pieces and brittle as though exposed to excess heat. The repairman fixed it free but made the point it was not covered under warranty. Next the heated dry cycle baked the water onto the dishes forming a white crusty layer. We have a water softener that works very well. We stopped using heated dry because it is too hot. Last night before bed, I was standing in the kitchen and I smelled something burning. My wife had mistakenly programmed heated dry into the cycle. Obviously this dishwasher is as much a fire hazard as the one it replaced but no recall has been issued yet.

Maytag French door model is four years old. Water accumulates on the freezer floor in small puddles. As I read other comments, this seems quite often the case. I should probably pull out the refrigerator to see if I have water leakage on my floor. From reading other reviews, it appears that Maytag does not stand behind the product. Am I forced to do the repairs myself, or am I forced to find a repair person and hope their fix eliminates the problem? Any advice would be helpful.

I purchased the Legacy series washer and dryer from Home Depot in 2005. For the first 3 years, the washer worked fine. Since then, it has all been downhill. When I use bleach, I have to run an empty load because for whatever reason, the bleach goes through to the next load which has resulted in a number of ruined clothes. The wash cycle leaves clothes dirty and some even come out partially dry?! The rinse cycle does not always work as more times than not, the fabric softener is still in the dispenser cup. The spin cycle is getting worse with each load. Sometimes I reset the spin cycle as many as three times at which point I hand wring the clothes. This creates a strain on the dryer as I have to run it extra long to dry the clothes. I am more disappointed than I can say. I will never purchase anything Maytag again and I will not purchase from the company who makes Maytag products.

We purchased this Maytag about ten years ago. We had an old brown one that had to be 25 yrs old and still going. This piece of junk has had two compressors; the ice machine hasnt worked in a year, and now it just went out again (third time weve lost hundreds in food)!!!! About the same time we bought a Woods freezer on the cheap, this freezer sits in the laundry room crap piled on it and around it and never have had a problem. Maytag = $2500.00 boat anchor.

The dishwasher stopped working. The lights on left side of control panel arent working; so, machine wont start. Then machine was purchased in January 2010 for $525 and not including installation. Kim says it will cost $129 for their repairman to come look at it. I wished I had read the list of complaints on your site first.

I purchased my new refrigerator in 2005. Within 3 months, the bottom freezer went out. I had purchased warranty and it was fixed. Again, the fan went out 1 year later with the same exact problem. Now, it went out again 2 years later with the same exact problem. I called Maytag and they do not care. They are rude and simply will not fix this refrigerator. The warranty is gone and again, I have to pay for this constant problem. Why doesnt Maytag own up and service this problem. Didnt we pay for this? It wasnt given to us free. Someone needs to step up and gets it resolved for consumers. If legal action needs to bring this to their ignorance, so be it. We all have spent a great deal of money on a refrigerator and all they do is say, is “Too bad. How can any company continue to be in business and operate this way?

Unless you’re doing laundry for an army don’t buy the Maytag commercial washer MVWP575GW. I should have gone with my original choice but my husband was concerned with the durability and warranty hence why we purchased this washer. It’s just the 2 of us and I frequently use the delicate cycle. Unknown to me at the time you can not adjust your water level so if you’re washing delicates plan on wasting a lot of water unless you only wash your delicates once a month. In my opinion delicates are undergarments, blouses, etc. delicate cycle in “deep water wash” only. As far as we can tell the wash cycle at its longest is 8 minutes which I guess for commercial grade is probably correct. However there is a presoak option that I don’t the believe does the work of a longer wash cycle. If you have to do a quick scrub on a piece of clothing as the washer is filling up you can not do this as everything stops once the lid is up.Last but not least the washer is loud it sounds like it’s going to break down at any minute. I’m sure many of the issues people have with products today are due to government regulations. I’ve tried contacting Maytag customer service on numerous occasions to see if I’ve been doing something wrong even though I’ve read through the operating manual several times, I’m currently on hold for 20 minutes. Doing the laundry has never been the highlight of my day but I never minded it until now. I absolutely dread it now. My suggestion would be if you like the features on your current washer, spend what you need to to get it working properly which is what I wish I had done with my 23 yr old washer. Worst purchase I’ve ever made!

We got our Maytag dishwasher in 2011. Weve experienced a lot of the same problems other people have mentioned. Control Panel was the first thing to go out. Now it has a foul odor coming from it and it doesnt get the dishes clean. The heating coil has stopped working and is rusting. This dishwasher is junk and Im very disappointed. I will never buy Maytag again nor any company related to them.

Bravos XL IS A JUNK. I have had this Maytag washer maybe 2 years at most and it is junk. I called. Told/complained them about the noise during wash cycle and spinning. The 10 years warranty is falsely. The 10 years warranty is covered only 2 components in the entire machine ???? and does not include the labor cost of $130.00 an hour. Sadly, I have seen many negative reviews their product. I didnt check reviews before purchasing, I knew I needed a large basin and wanted the deep fill option. I always thought maytag was a good brand. Now I am in a jam. ???? If you are looking for a new washer read the Maytag reviews before considering this brand. Live and learn. ????

The new technology on the washers is useless and saves no energy or water. People figure out how to get more water in the tub and use that setting. There is not small or medium water fill anymore.

This dishwasher has an electronic control panel that is faulty. Within one year of purchase, the control panel shorted out. It was replaced under warranty. Almost exactly a year after that, the same part failed for the same reason. This time, Maytag refused to replace it for free since it was out of warranty. A new control panel would have cost over $250. Disappointed with this Maytag product and their refusal to replace an obviously defective part, I decided to buy a new dishwasher from another manufacturer. Also, it did not make sense to me to spend that kind of money to replace a part that would continue breaking every year. AVOID Maytag dishwashers with electronic control panels!

We have owned a number of dishwashers, some cost a great deal and some were inexpensive. Our current dishwasher is a Maytag and it has proven itself to be the best dishwasher we have ever owned, not only is it quiet, it cost less to operate and cleans all dishes and utensils excellently.

I purchased a topload washer two years ago and the plastic lid has been replaced 4 times because it cracks at the hinges. It is obviously a manufacturers defect that Maytag refuses to admit. They come up with excuses blaming the consumer instead of their bad design.

We purchased a Maytag refrigerator (freezer on the bottom) in August 2012. In 2014 we had to have the freezer repaired (defrost drain) which cost $153. This month, July 2015, we had to have the refrigerator repaired for another $293. The problem with the refrigerator the repairman told us is the control board (p/n W10503278). He stated that they didnt make the first board very well and hes been replacing this part quite frequently for customers. I only spent $799 on the refrigerator and I already have $446 into it. That is half of what I paid for it! I wouldnt recommend Maytag to anybody!

My new fridge iced over top to bottom. It started making horrible noise then ice maker stopped working. Called MY repairman. Thats when I found out about all the ice. He told me to thaw out and hed be back. It thawed out and then freezer went out. ALL my freaking meats and frozen food had to be thrown out. Now water keeps Flowing out on my NEW tile! Called my repairman back. He came back then informed me it was junk! He said several other customers having same issue. My daughter has the same refrigerator and it broke down just like mine! My repairman also said a big issue with your junk was you used parts from other brands to fix!After reading all these complaints I can see no sense in calling to get it repaired. Its obvious we are all having the same issue. Maybe someone from your ** company could check them out. I dont have the money to buy another fridge! My 85 year old uncle with Alzheimers lives with me and I dont want him to slip on that water and hurt himself! I think all of these complaints need to go to BBB. Thats my next step. I believe you need to recall this junk or give us our money back! I need you to respond or Im going on blast to let everyone know how you treat your customers.

The washer and dryer were purchased together as a set 4 years ago in 2010. There have been times where I actually had clothes come from the washer completely and partially dry due to lack of water inside the washer! It fills based on how many clothes are in the washer or capacity that it senses. I have had so many clothes dry washed and torn up due to its use! If you set the washer to the wrinkle control position it does not go through the last rinse and spin cycle, you must reset it to the rinse, drain, spin cycle again in order to finish processing that load.It has already thrown its belt 2 times! Which my husband had to fix since we could not get in touch with anyone at Maytag who knew what we were talking about! If change gets stuck inside the washer bin in the little groove in the tank it is very difficult to get out, Im sure everyone has washed a pair of pants with the change still in the pockets, yes I know this is user error but if you dont know the change is in the little grooves because you cant see them, it stops the washer! So be sure to search this every time you do laundry!The dryer has a mind of its own! Sometimes it will finish drying your clothes, sometimes it wont finish the time set! Theres no reason just doesnt finish! There is so many reasons I will never purchase this brand again. Ive run out of room and patience. My clothes look like Im homeless!

Side by side refrigerator model #msd255oveu01. I bought this refrigerator Apr. 2011... The 1st year, the ice kept sticking in machine or freezing up. Now they have had to replace the modules 3 times. Once fall of 2012 and and again yesterday, 3/19/14 and they had to come back today to replace that one. I have called Maytag and they wont stand behind it since the warranty is over. I have told them that this is an ongoing thing with the ice maker and I have had to have it serviced ever since I have bought it. I told them from the git go that the ice maker needed replace. The ice dispenser also drops an ice cube on the floor on occasion and if I use crushed ice it jams up. This product is defective and is not a good product.

My Maytag Neptune washer was purchased last October 2010. In the past few months, the washer has been making a loud noise when spinning/washing. I had a Maytag repairman look at the washer, and all the barring, etc. needed to be replaced, which would have a cost of over $450.00! I am very upset with this outcome and just looked into it and found that this washer had recalls that the consumers were not properly notified about. The lack of recall communication is inexcusable, especially since I even went as far as to buy a 3-year extended warranty and still was not notified.What really set this situation was that the repairman suggested to not buy a Maytag washer and he added that it would not be a problem since Maytag has been purchased by Whirlpool and that the Neptune washer played a part of the ending of Maytag! This whole situation has really put a bad taste for any Maytag product, and all of my major appliances are Maytag as well as the dryer I just purchased a week ago, before I knew about all of the disappointment of Maytag. I am sure the response I will be getting will be as good as the notification of the recall, which will be nothing. Thanks!

First things first, Maytag Bravos washers are crap. Dont buy one. Purchased model # MVWB750WQ 06/12/2010 for $872.02 + tax. After 3.25 years the spin cycle started making extremely loud whining noises. Bought a replacement water pump for about $100 as several people were reporting the same issue. Before I had a chance to replace it the washer started leaking from under the washer. And not a small amount of water! Mats were getting soaked after each wash. I went ahead and replaced the water pump. But the whining noise, while diminished, didnt go away. And the leak continued. Based on what Ive read on this and other forums it looks like Ill have to replace the bearings for the tub. Not going to happen. Just ordered a Speed Queen washer for about the same price as the Maytag and I will never buy another Maytag (or Whirlpool) product again. Note that I purchased the Maytag at Best Buy. Its important that Best Buy take some of the credit for this issue as they are complicit in keeping these substandard products on the market.

I purchased a Maytag 2000 series washing machines. It broke and needed to be repaired within six months of purchase. It continued to break and need to be repaired numerous times and its only a little over 1 1/2 years old. It ripped and ruined clothing on numerous occasions. It would not drain and the door would lock with clothing inside thus ruining them. Both of these issues occurred on more than one occasion. Maytags solution for their defective washer was to keep referring me to my warranty. They were no help at all. My warranty finally came through for me and I was issued a full refund through the warranty I purchased at the time I purchased the washer. My new washer (which is not a Maytag) is being delivered Friday. So finally after being without a washer for over two weeks I will be able to wash clothes again. My experience with Maytag was frustrating and aggravating to say the least and I will definitely never purchase Maytag again. They are far from reliable.

Our brand new Maytag front loader has a optimum (LOL) soap dispenser that can supposedly wash several loads before refilling. BUT, the dispenser fills with water after one load and dilutes whatever soap is left! We talked to a authorized tech who said it was a poor design. That the unit wasnt sealed from water or it would be under vacuum. We called Maytag and they said something like, Um well it has sensors!! Did they explain how it would sense the diluted soap concentration? Nope. It should be replaced by MAYTAG! Knowing it is something that they sell that is defective. Right out of the gate!! The engineer should be fired, the quality department heads fired too!

Like others that have submitted a review, about six months ago, our then less than two year old Maytag Bravos XL washer became very loud. If the problem is the main bearing as others have suggested, its not covered under the 10 year warranty. Aside from loud noise, the washer has never performed to my wifes satisfaction. Neither has the Maytag Bravos XL dryer. Regardless of the settings, the dryer doesnt dry the laundry completely. Extremely disappointed with both the washer and dryer which replaced our 15 year old Maytag washer and dryer. We will be replacing the defective Maytags with another brand like LG or Samsung very soon.

Purchased Maytag washer 2014, first the porcelain in the tub chipped then 3 years later the control unit assembly and actuator went bad they wanted $464 to fix the machine, more than we paid for it. The dealer tried to sell us insurance for this product at a hefty price, I believe all manufacturers are making their products with a short lifespan and the way for them to make money is by not making a quality product like they used to do that lasted 25 years or more, the only washer out there that is dependable is speed queen made in the USA in Wisconsin.So we the consumers are the losers in buying washers that do not live up to their name, Maytag covers themselves by a warranty of one year period for parts and labor and if you do not buy the extended warranty at a hefty price you are out of luck - so my advice is when buying a washer read all the reviews and make your decision, but the best advice is buy a speed queen online for $600 and save $400 by doing that and get a quality washer that will last 25 years or more.

I called Maytags customer service about an over the range microwave that was bought 2 years ago and barely used. The mechanism in the microwave on the latch for the door, clicked into the body of the unit and therefore the door does not register closed which doesnt allow it to come on. After explaining this issue to the customer service rep, she insisted that the only thing that Maytag would stand behind was the part if needed. A service call would be between $100 - $150. The microwave isnt even that old and why would Maytag not stand behind a like new unit? I bought 3 Maytag products and I am now regretting it. I had asked to speak to a supervisor and she just proceeded to repeat the same thing the sales rep did. They will only cover the cheap part if needed.What happened to Maytag being top of the line? Apparently they dont care about standing behind their products and would rather you buy an expensive extended warranty to cover their cheaply made appliance. I think they should be under review as a company. I would somewhat understand paying if my appliance was 5 to 10 years old. But its basically new. How is there no protection for customers when it comes to purchasing lemons from an appliance dealer? I will NEVER buy Maytag again and plan on selling my 2 other newly purchased appliances before they have issues. Maytags reviews on social media are terrible. All they offer are the words Im sorry and I understand your frustration. I assume thats just what they have written down in front of them to tell everyone who calls with issues. How do you not stand behind your products! I wish I could select no stars vs the 1.

I purchased MVWB955FW (washer) and MEDB955FW (dryer) from AJ Madison and the units were delivered in December 2017. After using the washing machine 5 times the glass lid spontaneously shattered putting glass into the machine and all of the clothes. I called Maytag for a replacement/service and they had to reschedule as the lid wasnt in yet. A week later, I followed up with Customer Service only to find out that the replacement lid was also shattered. They didnt make a replacement lid without glass (not sure why you need to watch the clothes being washed). I was told that there were no replacement lids available anywhere. I asked about getting a replacement washer and was told couldnt do that.I asked them to pick up the units and refund my money, which they promised. It is now 2 months since the original call for service and I continue to have to follow-up with them (never get a call back) and STILL have the broken units in my house. I have since purchased a replacement set (LG) and waiting for my refund. I will NEVER do business with Maytag/Whirlpool again.

February 2011, I purchased a washer from Lowes and started having problems with the washer leaking and skipping cycles on the first week. Lowes exchanged the washer end of first week. The new washer started with not adding water in wash cycles. The repairmen sent by Maytag could not find any problem with the washer. The washer worked off and on for months with problems. Cycles with bleach added worked fine, but 3 or 4 loads later with no bleach having been added, it would produce bleach-stained clothes. The repairman came out again and could find the cause for skipping cycles, but suggested I run clean cycle every time I use bleach. It defeats the purpose of purchasing an HE water-efficient washer.The third repairman sat and watched the unit run a load and then he said I know what is wrong. He took the washer control panel apart and found the wire harness was not properly connected from tub to control panel. I have not found what causes bleach stains 3 loads after the bleach was put in the washer. I will not recommend this unit to anyone because of manufacturing problems with harness assembly.

On Nov 1, 2018 - 14 months after purchasing this top of the line refrigerator - the compressor broke and the freezer stopped functioning. I called Maytag Service who said the soonest they could repair it was Nov 12 - 12 days after it broke. Also they said my 10 year warranty didnt apply unless I had proof of purchase. I said I registered my product online when I bought it but they said they had no record. So they had to charge me full cost of service and parts which would be $1000-$1500.I then called LOWES SERVICE ADVANTAGE - I really like Lowes by the way - and they verified my proof of purchase and that in addition to the appliance warranty I have a 5 YEAR mechanical parts repair warranty through LOWES. Thank goodness I purchased the service warranty from LOWES because Maytag was NOT honoring theirs! So then a repair person from FAST APPLIANCE REPAIR INC came to fix the refrigerator and said because it was the compressor he couldnt repair it so I had to wait a few days later for the COMPRESSOR SPECIALIST to come out. The compressor specialist came and said he didnt have any in stock so had to order one.Six days later - Nov 19 - the compressor arrived at my house. I called FAST APPLIANCE REPAIR and asked for someone to schedule an installation. I said Im RETIRED and can do it any time. They said the soonest they could install it is NOVEMBER 28 - ONE MONTH AFTER IT BROKE. So now Ive lost two large drawers of frozen food that spoiled. I have no refrigerator this week for my birthday and for Thanksgiving. I have to wait another 9 days to get it fixed. I am NOT HAPPY. I am sharing this experience so anyone considering buying this or any other MAYTAG product will think very carefully before making their purchase. Also, be sure to buy from Lowes and get the Lowes service plan for any appliance. Ill try to update this if and when my refrigerator gets repaired.

I purchased my Maytag Bravos XL MCT because It could wash King size comforters/bed linen. I needed a machine that was large capacity. Also it was an HE washer that cut my water usage down quite a bit and reduced my water cost. Also this machine did a great job of cleaning my clothes and household items. The features were good. Variety of load type water temp if it was delicate, bedding, denim and more. I have had it for 5 years and so far no problems. It came with a 10 year warranty.

We bought this stove because of the self cleaning oven feature. What a ripoff! The Aqualift technology simply does not do the job that it is supposed to do. As the lady of the house says, Self cleaning means clean it yourself. Whoever engineered this thing needs to go back to school. Adding insult to injury, we have adjusted the oven temperature to its highest and it still cooks so low that a cake has to be cooked for half as long again than the recipe calls for or the middle of it is still raw. We would like to sell the stove but would hate to burden someone else with this piece of junk.

We purchased a Maytag refrigerator (freezer on top) model m1txegmyw00 in May 2012 and the compressor recently failed roughly 3 months from the two-year mark. We first noticed the issue this winter when the bottom level of the fridge start freezing our food. We adjusted the internal temperature setting down, but this did nothing. Then the compressor started cycling on/off for roughly 5 minutes at a time. After we noticed that, the freezer no longer kept things frozen. We called the Maytag repairman ($80 including taxes just to visit). He said the compressor is gone and that They dont make them like they used to. - I thought he was joking. He also recommended getting a servicing contract on a new fridge (but I would expect that from a serviceman). The cost to replace the compressor was over $600 and their work is only guaranteed on that part for 3 months (so anything else in the fridge could go wrong). I asked if we could have avoided this - he said it was possible that if we had unplugged the fridge for 10 minutes when we noticed the on/off cycling, it might have given the fridge time to reset (so take that for what it is worth). Our previous fridge lasted over 8 years - I dont understand how Maytag (owned by Whirlpool) can sell a high ticket item that will work for less than two years. I will not be purchasing another one.

When we moved to a new home, we upgraded all the appliances, including the microwave. This was four years ago. When the first microwave stopped heating the food after two years, we thought it was a fluke and bought a brand new one, since fixing it would have cost more. Well, I should have gone with another brand. This is two Maytag microwave ovens in four years! We cannot believe that a company who enjoys such a good reputation can get away with such shoddy products!

MAYTAG BRAVO QUIET SERIES 400 - Do not buy. Piece of junk. I have bought Maytags for years, but they really messed up on these. First I had a new dress in the washer... It ripped it all the way down the back. Last month my dryer went out. It was the heating element. When the Maytag opened up the dryer, all the lint had been going into the dryer casing instead out to the vent. The whole inside of the dryer was packed with lint... It was around the motor and was a major fire hazard. The Maytag man said it was the worst he had seen in his 30 years. This month my washer starts making real loud noises when it spins. Sometimes I have to run it through another spin. Then it just quit. It wont do anything at all. You hear the motor like it is hung... It just hums. You have to unplug it to get it to stop. Maytag repairman said it was the bearings ($300.00 at least) and the computer board had gone out. The repairman said it would cost more than to just go buy a new one. The Maytag repairman himself told me whatever you do, do not buy another Maytag... Now that is sad!!! I grew up with Maytag. My mothers washers lasted at least fifteen years. This is my fourth and last set of Maytags after these!!!

Maytag Bravo XL - We bought the set about a year ago, after high recommendations from the salesman at Best Buy. This washer does not clean clothes - they come out with soap & spots & white stuff, even after I use the deep water or the extra rinse cycles. These cycles take well over an hour. When they are finally finished, my clothes are twisted into ropes that have to be unwound & taken apart before putting in the dryer. I hate to think what its doing to more delicate clothing, getting stretched & tied up like that. This washer is awful - cant wait to get a new one. The dryer isnt much better - cant believe a $900 dryer doesnt have a steam refresh cycle! And the controls are so touchy - if you actually push them, they dont work. If you lightly hover over the button & barely breathe on it, it does - very strange.

Bought a refrigerator from Home Depot in November 2012 for a cost of $1,647.48. In August 2013 it stops making ice day 1, stops cooling & it is running nonstop, all lights on display go out day 2. Called Home Depot & was given another number to call, called that number was told someone would be out next day to look at it. Also told my warranty would expire in November & I needed to buy another warranty. Maytag customer service was very rude. If their product was any good why do I have to pay extra for another warranty. A $1,647.48 refrigerator that only lasts 9 months, REALLY!!! Do not purchase Maytag appliances if you dont want to lose your money. Shame on Home Depot for not standing behind their merchandise. If you have a problem while warranty is in effect, Home Depot should replace product.

MODEL: MFI2265XEM1 - ice maker dispenser leaked water while under warranty; took two separate technician trips to repair. Several months later, called Maytag regarding leak and ice at bottom. Technician replaced w/ grommet w/ larger dia drain tube extension; smaller dia causing backup of water & ice. Now, ice maker quit working completely, ice buildup in bottom part of refrigerator and freezer building up frost which means air is getting into the freezer, and yes, the freezer door is completely shut! Please advise if there is a class action suit. Will contact California Attorney Generals office.

Purchased a Maytag Dishwasher (Model MDB7749SBBO), total with tax $590.34 on 3/31/13. It wasnt a cheaper model, had stainless interior. Owning it after a 1-1/2 year, the Control Panel went bad. Maytag offered me for $267 for repairs and 1 yr warranty. Why thats about half the price I paid. My personal repairman told me the cost would be around $200 to replace the control panel. Why I could get a more inexpensive model for $300 and still get a year warranty. Very disappointed in Maytag quality of their product.

Maytag dishwasher mdb7749awm2 - It appears that everybody who bought one of these dishwashers has run into this issue at one time or another, and it usually takes one full year of use before the control panel goes out on these units, and in most cases, it has to do with moisture getting on the thin strip of wires leading from the control board to the control panel. It usually occurs right where the strip enters the control panel... There is nice little gap for moisture to rest right on the wires, which will eventually lead to corrosion. I included an image of what to look for (see the nice black rust areas on the wires? That was my problem, and probably yours, too). If you have some very, very fine sandpaper, and have patience, then you can get the rust off the wire, but be very, very careful, or you could take the small thin wire off in the process! Ive made this repair myself to my unit, and I did it for one my friends machines (it was a Maytag, and his lasted two years, but had the same problem, too), and both had similar problems and right in the same spot! After removing the corrosion, the system worked great again. However, before hooking the unit up again, I sealed the area with some silicone to hopefully prevent this from happening again. Now, Im not saying that this is the problem that you are having, but its worth investigating, and dont be afraid to pull-off the front panel...its just held on with an adhesive and will go back on with no issues. Anyway, this could save one hundreds of dollars in repair costs. I hope that this helps.

25 months ago, I bought a brand new Maytag stainless steel microwave. We had upgraded all of our appliances except the microwave when we moved in our home. Our first purchase was the Maytag refrigerator. Should have learned my lesson from that because after less than a year, the freezer on the bottom went out twice! We bought this new microwave to replace an old one that didnt match the other appliances and was worn out. Two months ago, the code SE started appearing and then would go away after a few minutes. Now it doesnt go away and you cant use the microwave. I finally called a repair person since its out of warranty and was told that it would cost over $300 to fix it. Really! Im so angry because now I have to take money. I dont have to replace a microwave that should have another few years of use. Nothing at all reliable about a Maytag. I doubt Ill buy anything else they make.

A little over two years and my Maytag dishwasher needs 300 to $450 in repair for circuit board or boards. The repairman said that they got cheap and left out a seal which allows moisture to get into the electronics, duh. They have a known problem but will not stand behind their screw-ups. Never again will I purchase Maytag, Whirlpool or any other product made by the bumbs.

We updated our 25 years old dishwasher, which ironically still worked, to a Maytag we bought at a BrandsMart in GA in November 2010. Sixteen months later, the unit just died. The panel would light up, but would not run. We contacted Maytag and were assigned a repairman (The Appliance Guy) who could not come to fix the dishwasher until 5 days later. Once he finally showed up, I was informed by him that the control panel for the dishwasher had two shorts in it and it would be cheaper for me to just buy a new dishwasher because the repair to this one would be $344.44. When I contacted the customer service for Maytag, they offered to let me pay for the repairs and then they would give me a six month service warranty for free. Does that make sense to anyone? I could buy a totally different brand, brand-spanking-new and have a twelve month warranty with a better product. I asked to speak with Cheris boss and got to speak with Aaron, who offered me the same spiel. Heavily scripted, I apologize that you are dissatisfied, but all we can do is give you the service warranty for six months after you pay for the repair. I asked him if he was reading a script and he replied no. Now I know that he had probably repeated these same words twenty times a day. Heres a thought, Maytag claims to be a green company, using less electricity and water, and saving the customers money and yet they are filling up all the landfills with these appliances that are not even five years old. How is that being a green company?You know how when you buy a nice new button-up shirt? The makers of that good quality shirt go ahead and sew an extra button on the inside bottom part of the shirt because they know that theres a chance youll lose a button. Well, Im thinking that Maytag should just start shipping a couple extra control panels in every box of Maytag dishwashers. Crazy idea, right? Okay, so an easier and cheaper way for Maytag to correct the problem is to stop making dishwashers. Go back to the drawing board, make the engineer who designed the control panel wash everyones dishes (as punishment and he can get help from the customer service people because theyre really doing nothing), start building the old design dishwasher that has the old switch and dial, and start respecting their customers. There, problems solved!

I moved into my home in July 2013. My kitchen came with all stainless appliances that appeared and seemed to be in excellent shape. I have been using the Whirlpool Microwave oven to heat foods (all in microwave safe) containers and dishes. This morning, I was heating a muffin, when suddenly I hear popping. When I looked through the glass into the inside of the microwave I saw sparks then flames. I immediately stopped the microwave. The fire apparently started in the area of one clip that holds the metal rack inside. In researching this issue online, I found hundreds of complaints from people who have experienced the same issue, and Whirlpool refused to replace the unit because it is out of warranty.

We purchased this model from Home Depot in February 2011. In July 2011, I found it full of water and dirty dishes after running a wash cycle. It was completely dead like it wasnt getting any power. I checked the fuses, etc. - nothing was wrong that I could find with the power supply. I called for a service tech that day and they sent someone out to check it. It was the control panel. They shipped me a new control panel and the tech came back to replace it under warranty. It worked great until July 2013. Again, it is full of water and dirty dishes, wont turn on and has no lights on the front panel. I called Maytag to get a service tech. The warranty is expired of course. They offered to sell me a replacement dishwasher at a discount for $409, Model # MDB7749SBW. Or I can buy an additional 1 year of warranty for $269. I also could buy a control board for about $150 online. None of these options is attractive right now, but hopefully if I get the new model, it will not have any issues... I wish they would just tell me it was a crap unit instead of giving me the option to either get a new one or pay for a useless warranty. I am fed up with this dishwasher. 2 control boards in 2 1/2 years is unacceptable and indicative of a defective unit or design. After reading the reviews here it appears to be a defective design.

All I ever heard was Maytag is the best so I purchased the washer/dryer over a year ago and have had nothing but trouble from the get go. It takes an hour and a half to two hours for a wash (if youre lucky). Normally, I almost always have to stop and restart it and move clothes around, babysit it. I cant wash but four or five garments at a time. Its a piece of junk and I tell everyone I talk to, never buy Maytag, ever.

Maytag Centennial Commercial washer - We purchased this washer approx 4 years ago and have never been satisfied with the job it does. Most loads require a second rinse cycle and then perhaps not a good job on the clothes. We have had it repaired twice as it makes a god awful noise and does not do a wash cycle. I believe the repairman has replaced plastic pulleys both times and now it needs the repair job done again. High efficiency has led to high disappointment. We will be looking at getting an older style agitator model as we know they work! Maytag will have to pay us to buy anymore of their products, not impressed at all.

I bought this washer 2 years ago, it has always been noisy and not cleaned or rinsed my clothes very well. With dark clothes, I have to rinse them twice if not three times. Now it has quit throwing out the water all together and is not rinsing the clothes at all. Paid $72 for a repair man to hook it up to his computer and tell me there was nothing wrong with it. Told me it was how I was loading it. I dont think so. Now I have to replace a two-year old machine. I will buy a basic machine that only washes my clothes this time. Nothing is made to last these days.

I had a stove my mom bought for me 26 years ago. Still worked perfect. Used constantly. In 2018 my husband had to have this stove. Said no my stove my mom bought and still works perfect sentimental plus three children using it. Not one problem. So he buys this Maytag stove I didn’t like but don’t cook much warming things up or frozen pizza. Go to our sons for holidays. Always next day cook a turkey for sandwiches. Open the door which is too heavy. Wouldn’t close and called my husband. Got it semi closed. Said we’re not eating it. He proceeds to cook. Door opened. More turkey is in garbage. My husband started reading. I also did. Looks like these Maytag stoves are garbage. Make a lot of money for repairs. Now this goes to dump. No one stands behind their products. Is it worth paying to repair no.

Read MANY complaints about these units leaking water onto the floor underneath. This is accompanied by a sheet of ice forming on the bottom of the freezer under the main drawer. Good money says the cause is a plugged drain tube. I had a Subzero that suffered a similar problem. The factory installed drain tube was a flexible coil type and food particles would be easily caught, compromising water flow - leading to an ice plug and eventual evaporator ice-over. I replaced the factory tube with 1/4-inch rubber fuel line and the problem went away for good. With the Maytag units, if memory serves, access to the drain tube is from the back of the unit. You have to remove an access panel to get to it. There is typically a small removable rubber restrictor cap on the bottom of the tube; this is the most likely spot for a clog to form. Due to its design, IMO, clogging and ice-over will probably be a periodic thing. If you are really handy, you can do this maintenance thing yourself.

My Maytag washer (model number MVWC400XW3) worked well for 6 months. Suddenly, it started making terrible loud noises when spinning. Repairmen have come out 6 times, and I got second opinions. It was turned over to another repair company. Transmission has been replaced as well as the motor. I have been without a washer for 3 months. Repairmen would come out, replace a part, and leave; and the washer is never fixed. I asked the repairmen to stay for an entire cycle, but they act insulted and left, saying its fixed. When I tried to wash, everything went crazy. I unplugged the washer and plugged it back in to reset it. I turned the dial to spin, and the lights said the washer was sensing. The lights never moved off that. The washer sounded like its trying to wash, but theres a strong grinding noise. When does the repairman decide he cant fix it? My husband is insisting we go buy another washer. The washer was bought in September 2011, so its still in warranty. In addition, we bought a five-year warranty. The repairmen stay 15 minutes, plug in a new part, and leave. They dont come back for two weeks. Will we ever get this washer fixed or get a new one. How do we put pressure on Maytag to fix it or give us a new one?

I have a Bravos washer model # mvwb45owqo and matching dryer. The price for the pair was $1347.00 plus tax. The washer and dryer were bought Jan 14 2010. 10-10-13 the pump went bad and was replaced. I paid $ 221.00 to have it replaced. 10-31-2013 I was washing a load of cloths and it was very noisy. I call the local dealer and they come out and said that it needs a drive shaft tub part #w10193886. I would be about $300.00 to replace the part. Also they charge $75.00 for a service call. I called Maytag and talked to Ashley (**) from customer service and she said they could not give me any help that the washer was too old. I might also add that my last washer was 3 years old and the motor needed to be replaced. It was also a Maytag. I always thought if you paid more money for quality it was worth it. I am sorry I did not buy a cheap machine from Sears or somewhere else. It would of been 1/2 of the cost and I could of replaced it after 3 years or so if necessary and still been money ahead. We also have 4 rental homes that have all Maytag in it. I will be holding my breath that they are not junk also. I will tell everyone I know not to buy Maytag and I will never own anything that has the Maytag name on it again.

I have had this washer 4 years...I bought this washer in May 2016. It makes 3 very loud noise as it moves into its next mode/cycle. Found out this is normal. IF, it is close to your living room, IT is loud.. I called again, saw that it was not filling up. 1/5/2017.. IT will NOT fill up to wash my clothes properly, clothes were still dry!!! Came out, (they sent a company near my area), said everything is right. I have tried, by sending messages, many times to get them to check. No one seems to care. The machine allows water to go out the bottom, rather than fill in the machine. I watched it myself. THERE should be a recall on this machine, definitely, something is sooo wrong.. I NOW have to put it on BULKY SHEETS full time, to get my wash clean.. NO energy savings there... BUT my clothes are finally clean!! Seriously, something is wrong...

Maytag Bravo Washer and Dryer - We are usually review writers. I just felt it was our duty to help others save their hard-earned dollars and not purchase this product. We have owned this expensive and highly researched set for a bit over 2 years. We have had to have repairmen out a half dozen times for dryer repairs. The washer was purchased with the largest tub because I wanted to be able to wash a full load of sheets or a blanket. NOT!!! It gets off balanced, twists every single item (as in blue jeans, towels, soft t-shirts, etc...any weight or size) into a huge mess and has actually ruined some of my clothing. The dryer gives me error messages all the time. I am beyond words with my disappointment. We saved a long time for this set and now are absolutely stuck for a long time before we can replace. You know Maytag my message to you is that hard-working people used to trust your company name. I have been married 43 years and we keep our purchases for many years. I have never in all these years been so disappointed in the huge purchase we made thinking it was a lifetime investment. Now I am doing everything I can to save this year so maybe can replace it down the road as soon as we can. I am telling you people reading this... DO NOT BUY THIS SET. IT IS A TOTAL WASTE OF YOUR HARD EARNED MONEY.

I bought a Maytag Bravos from Home Depot back for around $1000 in Nov. 07. After 3 yrs, the whole tub assembly had to be replaced but I had bought a warranty so that was taken care of but it was out of service for about 2 months while I waited for parts. Now every time I use it, I get the OL on the control panel and it wont spin without getting out of control and stopping. Washers in the past have lasted me at least 15 yrs and cost less than half that much. I will never buy another Maytag ever. This is what happens when companies merge and quality is no longer important. I think the stock market ruins companies. Im currently looking for the best quality, large capacity washer on the market. I will pay more for quality but thats what I thought last time.

Purchased MBF1958 model refrigerator July 2012. Has had 3 major problems. 2nd time the compressor has failed. For over 1 month have been playing phone tag and given the runaround by Maytag. Never return calls when promised and get a different story with each person I speak with. After 2 service calls to diagnose a bad compressor, $69 service fee, two weeks for the replacement to come in, the third serviceman decides this is not the problem and the refrigerator cannot be fixed. Maytag has once again offered to SELL me a replacement at a discounted price. Do I really want to subject myself to the HORRENDOUS MAYTAG EXPERIENCE again?

WE bought all new Maytag kitchen appliances and the extended best service contract. Cost 1/2 of the cost of the appliances. This was 3 years ago. Recently dishwasher went blank. Service call was a factory neutral wire. Then ice maker replaced with a reman unit. Then we thought something was wrong with the oven cleaning system aqua lift. So after many hours and calls two service techs told us the system will not clean the oven and after many cycles it will not and the bad part is they are still selling this system to the public. Criminal. I think they should own up to the public when they do this kind of thing. On top of this I would go buy the self cleaning oven but the tech even said he will not use it because it will break and need replacement. It is no better other than you can use oven cleaner to clean the finish without the heating element and you cannot use anything that works on the aqua lift finish. Bad deal.

This dishwasher is at 10 years old, but is a real workhorse. This machine cleans like no other! Never worry about our dishes being clean. But we have replaced the seal once.

I would like to start with, my Mother had always used Maytag washer and dryers. Her machines would last 20 years or more. I bought a Maytag front loader washer and dryer in 2006, since owning these machines have spent in upwards of $1400 in repairs. Some being flood out of tub, mother board blow out a couple of times as well as various other issues. The biggest problem is the awful smell of our clothes, I must wash clothes multiple times to try and remove these smells. I tried contacting Maytag and they dont want to hear my complaints and push me off to purchasing another washer and dryer. Oh, I will be buying a new washer and dryer it just will not be Maytag. Do yourselves a favor and DO NOT buy another Maytag. This is not the same company my Mother knew and trusted.

We bought a Maytag Bottom Freezer Model MBB1952HEW in 2006. We have already replaced the relay, two years ago, now the compressor is going. I have seen recalls of the top freezer on the internet but not on the bottom freezer. It is concerning when you pull your refrigerator out from the wall as to how warm/hot it is back there. We were told it would be cheaper to buy a new refrigerator versus replacing the compressor. We are so disappointed in how much money we have stuck into this refrigerator for how old it is. I would expect a refrigerator from a reputable company to last longer than 6 years.

We purchased a Maytag Washer and Dryer from The Home Depot in September of 2017. We did not purchase the extended warranty because of our confidence in the brand. Within less than a year, both appliances started making noises. By September of 2018, the washer sounded like it had a bag of mice squeaking inside every time we ran a load and had stopped spinning entirely. I called and spoke to a very kind lady who assured me that even if we were outside the one year manufacturers warranty, they would offer us the extended warranty without question because it was so close to the one year purchase. She took my credit card, we were charged for a five year plan and service was scheduled. After service, both units were still louder than I would prefer but the technician said it was common. Over the last few months, both have become louder and louder. Now the dryer shuts off and wont stay on. When I called back to schedule service again, the date of our purchase was all of a sudden in question. (I applied for the contract over the phone so THEIR rep entered the purchase date.) They are now telling us they will only honor the cost of parts and we are subject to pay for diagnostics and labor (which is the largest cost of repair). They are telling us our contract has to be cancelled and AFTER we receive and PAY FOR all but the parts, we can call and pay for a NEW contract. This has been the WORST appliance purchase we have EVER made and we have lost all confidence in the quality of Maytag/Whirlpool appliances. Both units have been VERY disappointing and we spent over $700 on each unit. NEVER AGAIN.

For the first time I bought a new washing machine in order to have one that lasted. Bought a brand new Maytag Front Loading HE washer model MHW3505FW1. Controls stopped working and the machine turns on and off by itself. Its either a faulty control board or computer, either of which are going to be more than a $400 repair. So more than half of what we can pay for a new machine. Maytag only warranties two parts for more than a year. So in reality, its not worth the repair and I will not buy a Maytag of Whirlpool product ever again.

Bought Maytag dishwasher model number MDB894995BB3 serial # F41103073. About 2 months out of warranty the control panel went bad. Contacted Maytag. After quite some time they agreed to pay for parts. After some more conversation they also agreed to pay service and labor. This was on the first day of August and Maytag scheduled a repairman for the sixth of August. When he arrived spent five minutes and said he had to order parts. The control panel I had already told them was bad. Now here I sit waiting for part to arrive. No more Maytag or Whirlpool for me.

Called to schedule service for letters on door to be replaced ice and water completely rubbed off until you didnt know which one you were getting. Refrigerator is less than 10 months old. Also freezer door was hung lower than refrigerator door. Was told nothing could be done. It was a cosmetic issue. Very rude customer service dept and I talked to two separate people and they were both rude and unwilling to help. I can promise you I will never buy any of their appliances again.

I bought this washer almost 5 yrs ago and oil has been leaking from it. Called company who sent a tech to my home and declared it a total loss. All he did was tilt it for maybe 1 minute to determine this. I am out a washer. Nothing from this horrible company. They quit making the washer but cant even compensate the owner with anything to purchase a replacement. Will keep passing the word.

We bought the combo Maytag Bravo 300. The issues with the dryer are that it doesnt heat right, have to run the thing twice, after the first 50 minutes the clothes are still damp and it sounds like its going to take off. We had a service man tell us that it was the fan blower rubbing. Now for the washer. It sounds like a b-52 taking off in spin cycle. I know that its the bearings, bearing kit 80 some dollars plus the bearing tool another 80 some bucks. Dont think Im going to invest in Maytags game. If there is ever a class action lawsuit please put me down or notify me.

I purchased a Quiet Series 300 E71195 dishwasher in 2011. Its about 3.5 yrs old. I guess misery loves company because like so many other complaints on this site my control board died, and Maytag, while saying they care about customer satisfaction, basically said tough luck pal, youre on your own. Sadly I own 3 other newish Maytag appliances. When will these appliances die without support from Maytag? Im not holding my breath. My next step is to complain to the dept of Consumer Affairs and create a page about nefarious Maytag on social media. Avoid the Maytag brand when shopping for appliances. I know I will.

I love the bottom freezer & refrigerator on top. Its so convenient... but it really could have a little more refrigerator space though. I love the stainless steel. It makes the fridge look regal. Also, the fingerprints do not show.

I have not found one feature that impresses me. Clothes do not always get clean (folds of debris). They do not spin dry enough. The cycle choices are ridiculously complicated. You cant add any clothes once the load has started. You have to wash the machine on a regular basis at about $3 per month. To get more water in the machine, you have to elect the Bulky cycle. Small amounts of bleach is so concentrated that clothing elastic is deteriorating and small holes may appear.The clothing most often comes out of the machine like twisted up tangled donuts. The cycles take about an hour and no longer match up to the dryer time - more trips up and down per load. The cycle guide is way too complicated - Normal Heavy, Heavy Duty Regular - whats the difference? Two service calls tell me there is nothing wrong with the machine - get used to it. I would much prefer the old agitator machine.

OK, LAWYERS -- Where are you?!! You have a lot of very unhappy people who feel they have been justifiably TAKEN! Whirlpool needs to replace these refrigerators with another brand! We bought same bottom freezer Maytag refrigerator in 2010. Luckily, which we dont usually do, we purchased a five year warranty plan. Within six months we noticed the rubber seal on our refrigerator on the french door part was turning yellow and then getting darker. We feared something was burning the rubber. A Maytag repairman looked at it, called Whirlpool, told them that there werent enough parts to fix this refrigerator. Whirlpool asked him what they should do and he told him it should be taken out on the front lawn and burned (yeah for that repairman)!! Whirlpool agreed to replace the refrigerator with one, very similar but a new model #. Thank heavens, after our insistence, the warranty was extended to the new one. Now after about three years, we are having the same problems that all of you are having with the next one.. Our Home Owners insurance adjuster just gave us a settlement to have all the ceramic tiles removed, which are cracked in almost two dozen places, and whole floor replaced (minus our $1,000 deductible). The floor was put in new three years ago. The refrigerator repairman is next to come out. From what I have just read about all the complaints on this refrigerator, NOTHING is going to fix this problem short of replacing it at our expense. My advise to everyone --- FIGHT THIS. Write to Whirlpool (not Maytag -- Whirlpool owns it), and blast them over and over with letters and complaints and threats of lawsuits. Why should we be taken for that amount of money while Whirlpool does nothing but keep it. A class action suit is badly needed. Big corporations should not be able to take people over like this and get away with it. If it takes a lawyer willing to take on a class action suit, this is it! In the meantime, bombard Whirlpool with letters and dont stop! It takes persistence, but in the end -- most of the time, we will prevail. Big companies hope we will give up and go away. They count on it. Dont let them win!!! I have had a Maytag washer and dryer for twenty years with no problems. Problem is that Maytag doesnt exist anymore -- who is making this....?

I have used Maytag washer and dryer for over 20 yrs. I recently replaced the set we purchased in 1988 because the washer broke down but I have never had a great problem with it either. I do on a average of 3 loads of laundry a week. I measure my detergents, mostly wash on warm or cold and I keep the filters and machines clean. I would buy the same maker should I need to replace them.

This review is for a Maytag Gemini MGT8775XW 30 Freestanding Double-Oven Gas Range w/ 5 Burners. I cannot believe the amount of problems I have had from this $2000+ range. Within just a few weeks of getting it, the paint started scratching off the surfaces nearest the heat. Then, the plastic cover over the digital display and controls bubbled up due to the heat of the broiler being in use. They designed it so that the heat escapes from the oven right in front of the control panel, so when you want to adjust temperatures on the control panel, you chance getting burnt from the hot air every time.The very worst design are the manual knobs for the burners on the front. They are at an angle, and if you look at the oven straight on, you see they are higher than the burner surface. A hot pan that overhangs the burner cooks the knobs. The plastic interior of the knob lacks any kind of heat resistance and actually starts to turn soft, keeping you from being able to turn off the burner at all!Most dangerous of all, the knobs are frighteningly easy to bump, pouring gas into your house. We have had this problem multiple times. Today, my dog must have wanted to investigate the top of the stove, because when I came home, the burner was on, had burnt through a pot on the stove, and was just at the ignition point for an item sitting next to the stove. If I had come home 15 minutes later, my house would be in flames right now. I am having to air out my home as I type this. I am DONE with this dangerous oven and will be shopping for a new one, and it certainly wont be Maytag.