We love our Maytag ovens. It always cooks evenly and we never have HAD any issues over the past 2 years. We will always buy Maytag! It has a self cleaning option and I have never burned anything on the oven.

We bought a Maytag Bottom Freezer Model MBB1952HEW in 2006. We have already replaced the relay, two years ago, now the compressor is going. I have seen recalls of the top freezer on the internet but not on the bottom freezer. It is concerning when you pull your refrigerator out from the wall as to how warm/hot it is back there. We were told it would be cheaper to buy a new refrigerator versus replacing the compressor. We are so disappointed in how much money we have stuck into this refrigerator for how old it is. I would expect a refrigerator from a reputable company to last longer than 6 years.

I purchased a Maytag dishwasher model MDB7749AWB2 in Dec. 2011 from Home Depot after a major flood destroyed my entire first floor of my house. I had replaced a previous dishwasher only a short time before the flood. This dishwasher is JUNK. I was lucky I bought a five year extended warranty on it which actually gave me 6 years. I needed it. Within a year the control panel went. Then water started spraying out the side of door. Then it sounded like it was crushing ice every time I ran it. Then the control panel went out again. Ice noise came back again. Control panel a 3rd time. It runs for hours as it is.Now the warranty is expired and last time I ran it the start light was blinking a few hours later. We were having high winds on and off so I thought maybe the power went on and off and that’s why it was blinking. Today I turned it on and after about 45 minutes I realized I didn’t hear it running anymore so I got up and looked and sure enough it wasn’t on. Normally the clean light is lit when done. I opened the dishwasher to see it filled with water still. I tried to hit cancel/drain but nothing works yet again. Wonderful news for a single mom that can’t afford to fix this over and over! Maytag is the worse company. Their dishwashers are horrible and they should be doing something about this as I’m not the only one that has had this issue. Home Depot was just as useless. Will NEVER buy again.

This Maytag (Whirlpool) model MDB7749SBMI dishwasher was purchased 10/28/13 at Home Depot. That makes it 2 1/2 years old to date. It has been a good dishwasher up until now. A few weeks ago I noticed it was doing something wonky. First of all it was not responding its usual way when I tried to turn it on after closing the door. The start button was not responding immediately, nor were some of the other buttons. I also noticed that after the dry cycle had completed and the door was then opened to unload, that the lights on the door were flashing. Then, when I shut the door after unloading the dishes, the washer would come on without having any buttons pushed. Recently, in addition to the difficulty we are experiencing getting it to start, the washer will keep running without ever turning off. Last night I turned it on before going to bed, and it was still running this morning. Calling the service number, the control panel part will run around $150, with a $98 charge for repairman to come out. Who knows if that 98$ isnt just to walk in the door, and whether that includes the time it takes to install the part. The dishwasher was around $400 with my husbands military discount from Home Depot, so it seems crazy to spend that kind of money to have a part replaced that is going to break again because of PLANNED OBSOLESCENCE. If that part is replaced (at half the cost of the dishwasher) whos to say what other part is going to break next, perhaps requiring another service call plus price of part. So, conclusion is to throw this one in the landfill and purchase another dishwasher, sadly.The case of Planned Obsolescence is reflected in many of the comments/reports here on Consumer Affairs. The age of the failing control panels of the Maytag/Whirlpool washers are running around the same time spans. No doubt in my mind that these control panels are designed to fail after a specific amount of run cycles/time on this machine. These appliance companies that are manufacturing these total crap appliances so that people will have to buy replacements within 3 or 4 years are filling our already packed landfills while robbing the consumer. Its plain to see for all who care to investigate the matter. A service repairman whom Ive used for years and has been in the business for 25, told me that most appliances today are total pieces of junk compared what they used to be and are designed to fail. He said it has greatly impacted his business because people are replacing appliances versus repairing them because it is not cost effective to have them repaired. He also added that the guts of these appliances looked like they were made from Cracker Jack toy quality plastic materials. There should be laws to stop these manufactures from Planned Obsolescence, and we need to go back to the way appliances use to be made... to last! I have no idea what its going to take to ever see that happen. This is what happens when you have very little competition and 2 major appliance manufacturers. More parts are being designed to fail, so that they can line their pockets. Pitiful.

Maytag dishwasher model MDB4949SDE3: This dishwasher is the biggest POS that I have ever owned in 40 years. The first one would never turn on and fill with water and after it finally did it leaked on my new floor. Waited 10 days to have it replaced. The dishwasher cycle is 2.5 - 3.5 hours and the dishes come out dirty. The top rack is not adjustable to wash odd things. I feel that these dishwashers need to be replaced.

Maytag washer MVWC565FW - Clothes do not wash. They just get pushed around and the soap scum is left on the clothes even with the water at the highest level. I bought the washer override lid switch at a appliance parts store just to observe the washer cycles. The washer did not wash the clothes. I took the washer back. I like Maytag products but this washer has to be engineered.

Approximately one week ago, the display on my fridge began to flash and ice door flap continuously opens and closes. Upon researching the issue, it seems to be a very common issue and a known defect. One in which was apparently a recall at one point. I was told by a Maytag representative that the recall was from 2007 to 2009 and has since expired. Expired? Its a known defect and should be the responsibility of Maytag to provide the parts and labor to repair the fridge. I asked for a supervisor and was told that one would contact me within 24 hours. Well, about a week later, I never received that call so I called Maytag again. This time I was told by the maytag representative and a supervisor that there was no recall and that it was a Quality issue. A play with words, in my opinion. Anyhow, regardless of the title the issue was given, I was told I would be responsible for the repairs and costs. I attempted to look up the recall on Maytags website and had seen the last two letters of the serial number to my fridge listed under the recall, but when I tried to investigate further, the site referred me to the 800 phone number I had been calling. Now, had this been an issue that was not a known defect and apparently a recall, I wouldnt be writing on this site right now. But, because it is a known defect that maytag is aware of, I think its Maytags responsibility to pay for the parts and labor for my fridge.

3 months after we purchased our Maytag dishwasher in Jan 2014 (Sears) it broke. The service person told us that the ELECTRONIC CONTROL PANEL (START, CANCEL, WASH CYCLE SELECTIONS) was a common breakage issue and fixed it. It broke again around one year from our purchase date. Same issue, but kept working and not working. Finally we contacted Maytags customer service. Although courteous the only thing we were offered for this common Maytag issue was a $249.95 one year warranty for them to come and fix this recurring problem. I explained that we had already spent about $870 (including tax, delivery and installation) for our middle of the line dishwasher one and a half years ago and asked if they would consider either charging us for a smaller service call/repair or just do it because it seems to be a design and manufacturing issue. After one hour and no sympathy I had to pay the $249.95 to get a repair person out and be covered for one year from today. I dont trust the cheap quality and the lack of support for the product. THEY ARE OUT THERE TO SELL MORE INSURANCE AND CUSTOMER SERVICE DOESNT MATTER!

I purchased the washer 12 months ago. I liked large tub size and Maytag name. Thought I had made a good purchase. Boy am I am sorry. The washer overflows my large utility sink for drainage on large load setting and clean setting, ruining the flooring in an adjoining room. You cant wash black clothes in it leave white residue spots all over clothing. You cant use pod soap. Doesnt dissolve totally. Just on your clothing so you must wash again. So now I am trying to figure out what I can do but afraid I am going to replace it. Would Not recommend this product. Bravos XL MCT MVWB835DW1.

I purchased the Top Loading Maytag Washer and have had nothing but an awful experience with this washer. The dark clothes come out with soap on them. I then need to take a wet towel to wipe out the soap stains. I have had a repairman in 2 times so far and there is nothing he can do to fix it. Maytag said I must wash all the towels with towels, all jeans with jeans, roll clothes into a loose ball before putting in machine, use the extra rinse cycle and the longest wash cycle and do not load clothes more than 5-6 inches high in the tub plus 7 other things I must do to get a clean load and none of those things have worked yet. If the salesperson would have told me all this, I never would have purchased a Maytag and nor should you!

I would like to say that I am highly dissatisfied with paying $1200 for a refrigerator that only can produce ice once every 12 hours and 90% of the time the over fill lever gets stuck so it will not make more. I would recommend anyone to not buy anything Maytag ever.

Our brand new Maytag front loader has a optimum (LOL) soap dispenser that can supposedly wash several loads before refilling. BUT, the dispenser fills with water after one load and dilutes whatever soap is left! We talked to a authorized tech who said it was a poor design. That the unit wasnt sealed from water or it would be under vacuum. We called Maytag and they said something like, Um well it has sensors!! Did they explain how it would sense the diluted soap concentration? Nope. It should be replaced by MAYTAG! Knowing it is something that they sell that is defective. Right out of the gate!! The engineer should be fired, the quality department heads fired too!

In the winter of 2007, we remodeled our kitchen and bought all new Maytag appliances. They cost a little more but we felt that we were getting a good quality product. Within months, the handle on the freezer became loose and I had to call for a repairman to tighten it. He told me we should buy the extended warranty because only a trained repairman could fix the handle. That turned out to be untrue thankfully because if it was true, I would have to call for repair at least once a month. The handle is constantly coming loose. A few months later, the microwave would turn on when the door was closed. I called repair as it was still under warranty. After he removed and replaced the door, I was told that we have to be careful when we close the microwave. There was nothing he could do to stop the problem. Approximately three years after we purchased the appliances, we had a problem with the dishwasher. We could only use one function; the others would not work. We were told by the technician that we got water into the door where the controls are and ruined the motherboard. I never heard anything so absurd. I have had a dishwasher in the same place for 25 years with no mishap. The cost of repair was $800. A few months later, we had a problem with the large burner on our cooktop. The outer coils heat up but the inner coils do not. I have yet to call for repair because I do not trust Maytag. Now, our microwave does not work. My husband used it to make popcorn with no problem. A little while later, I tried to heat a cup of coffee and it would not heat. The keypad works, the light comes on in the microwave but the motor does not run. Needless to say, we are very unhappy and will never buy another Maytag appliance. I wish I would have read the reviews before we purchased the appliances. Two of our friends had their kitchens remodeled at the same time we did and they have not had any problems with their appliances. But they didnt buy Maytag. I guess thats why.

Totally DISGUSTED!!!! Have owned my range for several years! Love have double ovens, however it is double the repair!!!! Every year we must have the handles replaced as the connection loosens and handles fall off!

I bought the dishwasher (Model MDB7749AWM) 15 months ago and paid $490.00. I had to put a new console in it ($245.00) on 07/16/2012. So that’s $735.00. Two days ago, the console went out again! I’m not putting $245 more in it! I called Maytag’s office. They more or less told me that was my problem! I am throwing that piece of junk away! And I’m buying a different brand. Maytag does not stand behind their product. Last Maytag I will buy! Warning! Do not buy Maytag!

Maytag Quiet Series 200 only 1.2 years old: I moved into my home about 2 months ago and the touch panel on the dishwasher, which is of course just past the warranty expiration date, has progressively gotten worse until now, doesnt work at all. I have tried calling Maytag many times on numerous occasions, who apparently only has one phone line because its ALWAYS busy. The cost for the touch panel on this dishwasher (model# MDBH945AWS3) is $150 which isnt even worth fixing since I can go to Lowes and buy a new FRIGIDAIRE for $300. The problem is the circuitry from the touch panel to the control board gets too much moisture in it with no protection around it. If I were them, I would find a way to make all these parts separate so regular people, like you and I, would be able to buy parts a lot more cheaply and repair these items ourselves. However, since the front panel and the circuitry attached to it is all one cohesive unit that cant be taken apart from one another, nearly at all without ruining it, then I might have been posting a different review here. However, that is not the case. IF I could actually get in touch with Maytag, I would ask why on earth isnt this a recalled item and when they are shipping me a new part since it seems everyone is having the same issue with their Maytag dishwasher, no matter what series it is. I do not plan on buying a Maytag appliance in the future. I do plan on buying a Frigidaire since the rest of my appliances (stove, fridge and overhead microwave) work perfectly without any issues whatsoever.

My stove is approximately nine years old. During the past year both my husband and I enjoy cooking from recipes 3-4 times a week thus the stove has become essential. Functionality and size is important when trying to cook meals with two or three components. One of the oven racks was missing from the oven when we moved into the house. Even though it is self cleaning, spills pile up between cleanings so it is great that it has a really cool steam cleaning option. Just wish it were 5-6 years newer.

I bought a Maytag Bravos Quiet Series 300 washer just over two years ago from Home Depot. The control board and sensor went out last week. The service technician seemed rather surprised that a newer machine would have that kind of non-wear-and-tear problem and suggested that I contact Maytag/Whirlpool to see if they could help offset the parts costs, as the repair was going to cost over $600! The customer service agent I spoke with said that there was nothing they could do because the item did not have an extended warranty. I explained to her that we purchased this unit, even though it was out of our price range, because we were told that it would last a lifetime. I would have been happy if it would have just lasted 5 years! She was very detached and it was clear that Maytag/Whirlpool was not going to stand behind their product. I will now take the repair money and go buy a new washer. You can be sure that it absolutely will not have the Maytag/Whirlpool brand!

After replacing plastic parts that spin tub twice, now the computer is wasted. Purchased not even 3 yrs ago, now I have to buy a new washer because the computer system is not covered under warranty. REALLY!! The most expensive part. Not worth fixing. Never washed really dirty clothes when it wasnt broke down. Agree with the class action I would be in. Dont buy people and now I am off to pay to wash my clothes.

Our $1,000.00 Maytag Bravos is only 4 years old (also bought the matching dryer at the same time). We have had to purchase two new motherboards for the washer and now the uL, during the spin cycle, comes on and my clothes will not spin out. I have followed the manuals directions to unplug, wait, replug, redistribute, etc... all to NO avail. So very disappointed with this machine. Bought it because it was a Maytag, but will never buy another :( I had this machine repaired with major amount of parts and expense (due to the uL problem), BUT the uL code still keeps coming up. I am one really unhappy customer.

I purchased a washer/dryer, Maytag from Home Depot Nashville. It was delivered and set up. 02/24/17 the date of purchase, delivered 03/07/17. I have tried in every way to get the washer to wash properly, but to no avail. The water level doesnt cover the clothes, it takes 10 to 15 minutes for the wash to begin its cycle. It doesnt spin the clothes dry enough to put into the dryer. The washer makes all kinds of sounds thats drives you nuts while setting up to not wash your clothes clean. I have contacted Maytag on several occasion about this problem, they sent out someone to service the washer. Now, why would a brand new washer need servicing. Somethings wrong. It isnt functioning up to standards and they should give me another washer.Now on 05/18/17 the washer was serviced, I have called them again to do something about this piece of **. I was told that the only thing they could do is come service it again. Why, must this brand new washer be serviced every week. It doesnt make sense... I dont want this machine, I want my money back so I can purchase a machine that will wash my clothes properly. I purchased a secondhand washer and dryer from a used appliance store, it lasted my family 10 complete year. The only reason I dont have it now is because I wanted to upgrade, since I have never had a brand new set. What a disappointment. Everything that looks good from Maytag isnt good. I dont understand why they wont stand behind their product.Somethings got to be done about this. Maytag will not take my money 1,200 and force me to keep this malfunctioning piece of nothing. Im going to Youtube this product so the consumer can see how this product doesnt work properly, therefore they wont waste their hard earned money. I will be contacting the BBB Nashville, and wherever I need to. I will let the consumer know the make and model of this product and where it was purchased from. Maytag I want every penny back. And, should hold you responsible for ever time I have had to go to the wash house because my brand new set wont work, and your company wants to service it every time I try to wash. I purchased this appliance on the strength of the well known name, that was the wrong thing to do.

After only three years of gentle use, my Maytag front loading washer bearing went. The repairman said this was because of too much detergent and the repair bill would be over $1100.00 (more than the cost of a new machine). I would never buy this machine again.

I believe the Maytag Bravo washer and dryer was manufactured so the Maytag man would have something to do once again! Buyers Beware! My $800 washer broke down 1 week after warranty costing me $400 to repair!!! Half the cost of a new one... now the dryer is making horrible noises. I fear calling for repair... or should I just buy a new different one?? My last washer and dryer lasted 30 years!!! Bravo certainly did not have all the kinks out of them before marketing them! The cost is to the consumer who trusted the name! You cannot return a 2 year old appliance! The laundromat would have been less costly than this washer and dryer! Maytag should be made to recall these defective machines or at least repair for free. Do not buy!

This is the best microwave that we have ever purchased. I especially like the baked potato choice. Its also very easy to use and clean. I would definitely recommend it.

New side by side, water inlet to ice always freezes. Had a service man out, said some tube needed to be enlarged but still freezes up.The ice dispenser is total junk. Keeps spitting out ice after glass is removed and just a poor design. Dont recommend this brand.

I have had the washer and dryer for a little over 2 years. The washer already needs to be replaced as the cost to replace the drum is almost as much as a new washing machine by another brand. Thought Maytag was the very best. I had a GE washer for years before I purchased this set. The GE wasnt broken but THOUGHT I was upgrading..NOT!!! Will not purchase Maytag again. Very unhappy!!!

I bought a Maytag washer from Lowes and bought the extended warranty. The warranty expired but Maytag is not taking responsibility for the lemons that they sell. I have seen many reviews stating that the bearings went on the washer. This is what happened to me and it happened twice already. I spent 798.00 on this washer thinking it would last for more than 6 yrs. They offered me a warranty for 368.00 or to purchase another washer at a discount price. Of course I refused but I want everyone to be aware of Maytag Washers - not worth the money.

Have been very disappointed. The burners keep going out. The repairman said a bug could crawl on the element and break it. Then the temperature on burner on it works from med to high and any lower no heat. The dual burner is now backwards. The oven handle keeps falling off. Worst range I ever had and I thought it was a step up to Maytag.

I bought the Maytag Bravos because I was told it was top of the line and expected that Maytags reputation for quality would provide me with many years of dependable service without problem. Boy, was I taken for a ride! Unless you have a lot of money to spend, DO NOT buy a Maytag Bravos washing machine. After only 3.5 years of normal use (3-4 standard loads per week) and doing everything as suggested by the owners manual, my machine has developed a bad drum bearing. The cost to repair this bearing is $400 for parts and $200 for labor. In other words, I am forced to buy a new machine after ONLY 3.5 years of use. When I called Maytag customer service department to question them about my problem, their response was there are no recalls on your machine, so we cannot do anything for you. When I further questioned them about the lack of quality/dependability my machine provided, they again said, Sorry, the machine is out of the warranty period. Thank you for buying Maytag. If you buy one of these washing machines, you better have the extra money to buy an extended warranty.

Zero should be a choice on overall experience. I purchased a Maytag Bravo 300 from Lowes in February of 2011. Last week I was doing a load of laundry and the washer stopped in mid-cycle, and it gave an alarm and error code ld. I checked out the manual and it said there was a problem with the drain line. I check the drain line and it was fine, so I called Maytag to have a service man take a look at it. Before he even looked at the washer, he said it was probably the pump, and it is not covered under warranty. And he said that it would cost $140. He obviously sees this all the time. He explained that the pump is too small for the unit and it does not allow anything to go through the pump. Please make sure anyone who may be considering buying one of these units knows right up front that they are going to have issues with the pump, even if a small pebble gets caught in the pump.

Purchased an expensive brand new home which had Maytag appliances in it. After about 1 1/2 years the freezer bottom began to constantly freeze and drip onto my floor. I researched the issue and found it was common, simply thaw the area where it freezes. Did it multiple times, we do not overfill our freezer etc. We must take the ice out of the bottom every 4-5 days. My hardwood floors are destroyed now. We purchased a Samsung fridge freezer bottom when they first came out years ago, had it for 7 years, 0 issues, but it went with the house. Now my Maytag oven door is locked shut, also it takes a very long time to boil water. Maytag junk. I am going to buy another Samsung fridge tomorrow.

Maytag Bravos XL HE MVWB725BW. Washer was fantastic at first. Then about at 14 months old, the spin cycle starting making loud noises. Called Maytag, they promptly dispatched a repair service. The estimate to fix the washer was $531. The repair man stated Maytag does NOT seal the bearings from the factory. They only rely on a rubber washer, poor design. Maytag was unwilling to help with a washer with their name on it that failed at 14 months in any shape or fashion. She mentioned that Maytag has a 2-10 warranty on the motor only (which is non-existent, its electromagnetic). This will be the last Maytag that I ever intend to purchase.

I purchased a Maytag Dishwasher in March 2013 and the control panel failed in July 2014. I, along with hundreds or thousands of others it seems, discovered that this is an extremely common issue with several models of Maytag dishwashers. Rather than standing behind their products and making it right for their customers, Maytag is hiding behind their one year warranty and refusing to do anything about it or even admit they installed thousands of FAULTY control panels. This has been an expensive, infuriating issue to deal with and I have never been so dissatisfied with a company. Bottom line, they made a bad product that should have been recalled. It blows my mind that they are getting away with this. I wish I had known the recent changes in Maytag/Whirlpool and I wish I had done my research prior to the purchase.

I just purchased a washer in April and the door is locked with my son brand new clothes is stuck in the machine in water, I called to get service and was told a date 2 weeks away, worst experience ever. Sorry ma’am is what I was told in a non caring way. I’m so furious if I could return this washer and dryer I would.

Purchased a Maytag OTR microwave in May of 2017. Started having issues with the Open/Close Door malfunction by September. Repair came out and essentially told us to keep opening and closing until it worked. It is January 2018 and the issue has gotten worse. My question is, since Maytag is keenly aware of the problem and has for years, based on other reviewers on here, why hasnt a class action lawsuit been filed? These appliances are expensive and it sounds like many of us have been taken to the cleaners!

This is a portable dishwasher. It does a great job washing the dishes. It’s fairly quiet and gets them very clean. It moves quite easily. The silverware tray is generous. The cycle takes a bit of time, but I don’t think it is excessive compared to other brands.

We purchased our home in late 2010 and was excited about our HE front-load washer (and dryer). Immediately, we noticed mold on the rubber boot, and the smell was horrible. We ran the washer with Affresh several times and left the door to open when not in use, and that seemed to help. Then most recently, the washers been shutting off mid-cycle through normal wash setting. I used to pound the washer out of frustration, and that seemed to get the machine working, but now it doesnt work at all. We had a repairman come out, and he charged us $94 to basically remove debris from the drain hose, and he told us that if the washer fails again, wed be looking at an expensive repair cost pertaining to the central control unit. We had a second repairman come out and replace the central control unit. It worked while he was here, but now its messing up again, shutting down mid-cycle. I have to unplug the washer for hours, replug, put it on rapid wash cycle (and hope it doesnt fail), and if it fails, then unplug, wait, put it on spin cycle... Its aggravating, and were looking at $300 to $400 in repair costs. Our repair man says front loaders are a nightmare (and he still has his non-HE washer from the 80s, and its still working). Our washer is Maytag Epic Z, model number MHWZ600TE00. Avoid front loaders, and definitely Maytag or Whirlpool front loaders. Well need to shop around for a new washer, an old-fashioned top loader this time.

I bought a Maytag washer and dryer with Commercial Technology, front loader in April 2012. Since then, the repair guy has been at my house three times in six months. This last repair is going to be just $800 in parts, not including any labor yet. So, I called Customer Service, and told them I was not satisfied with the repair job again, because I obviously have a lemon of a machine. Needless to say, I lost, and was told the warranty is only for repair, and not replacement. Well what happened to customer service? Its more like customer bend over, shut up and take it. So, I will get my repair at a cost of at least 1,200 bucks paid for by Maytag. Im not a business person, but if I were the company, I would think replacement of the unit would be a lot cheaper in the long run for this company and a happy customer for the future of me buying brands. Needless to say, I will never buy a Maytag or Whirlpool product again, and you can thank your useless Customer Service department in Canada for that. P.S. I work for a company with over 10,000 employees. I might accidentally send out a little free publicity how this company treats loyal customers. I actually bought this brand because in the past, I was led to believe they were great . Wow, was I wrong!

I have had my washer and dryer for more than 5 years. As normal, over time, stuff wears out and parts need to be replaced. The manual doesnt list part numbers that are needed. The website doesnt pull up part numbers when you type in the model number. After paying for overnight shipping that isnt guaranteed (and was more than the part itself), it didnt show up until a couple of days later and it was the wrong part. I would have to pay for shipping costs of the return, now tripling the cost of the actual part. Calls to customer service were not at all helpful as all they could say was that I would have to pay for the return shipping and they were sorry there was nothing they could do. I wont be purchasing anything from Maytag ever again.

I am sorry I purchased this machine. It was meant to replace a 17-year-old Maytag dishwasher that was not repairable. I figured they were good machines. Wrong. Perhaps I have a lemon, I do not know. I bought the machine on the 23rd of November and it was installed on the 29th of November. Here it is December 12th and I am sick to my stomach. I have already had to contact Maytag customer support and have a repairman coming. This machine does not clean worth a damn! My glasses look worse coming out of the machine than when they went in. I have run two loads with the machine so far. The auto-sense cycle is a joke. It took over four hours to complete and things did not come out clean. Last night I tried the normal cycle. It came up with a run time of 2:36. The first rinse was cold water. The detergent cup was open and empty at 20 minutes in. So what does the machine do for the next two hours??? When the cycle was finished I looked at the glasses and they were spotted and streaked with remnants of fingerprints and lips. So I ran it again trying the quick cycle. Not one bit of difference, still nasty looking glasses. If this machine cannot get the upper rack clean, how can I be sure the lower rack is getting sufficient cleaning? One would think that for $600 it could at least do the job it was meant to do.

We bought a Maytag Bravo washer and after less than 6 months of use, it stopped working with an F51 or 53 error (cant remember which because its been a month now). After looking online, it seems that almost everyone who buys this gets this error and has to have a part replaced! And Whirlpool hasnt recalled the faulty part even though everything Ive read says it should be a recall.Its now taken over a month to get a repair person in to fix it. From the time we called Maytag, to the referral to the service person, to the service appointment, to waiting over 2 weeks for the part to come in, its been over a month with no washer. This is unacceptable Maytag! The repair company is finally showing up tomorrow only after 3 left messages from us.Either build a better washer or stock your replacement parts with the local repair companies and you should be reimbursing your customers whove spent a lot of money at the laundromat after spending between $700 and $900 on your washing machines.

Bought a Bravos, large capacity, top load washing machine few years ago. (Purchased at a Lowes.) Been nothing, but one problem after the other!! I hate it! NO MORE MAYTAGS FOR ME. Has required several repairs of various parts. Now again, after being repaired few months ago, something else has gone wrong. Would have been cheaper to replace a 3-4 year old machine than keep having repairs.

We purchased this washer 8 months ago, and still do not have a working unit. From the very beginning of installing the new washer we had repeated F4 and E1 error codes. A technician was sent out three separate times and they replaced the ACU each time only to have the same error codes recur. This unfortunately took 5 months as each time the ACU part was on backorder. After 3 failed attempts they agreed to replace the washer with a new one. We were dumbfounded when the new unit arrived and we had the same F4 and E1 error codes! They have again replaced the ACU and still we have the same error codes! They are sending yet another ACU but we have little confidence this will work and we are at a painful 8 months with no washer.

I have had this refrigerator for a few years and never have had a problem. It keeps food uniformly cold, and is frost free. While appearance is attractive, it doesnt look like a $3,000 refrigerator. However, black pebbled-surface exterior is easy to clean and scratch-resistant. Plastic and glass interior fittings also have held up very well. I originally thought it would be too small because I was buying it to fit a certain space in the kitchen. But it has turned out to be just the right size because there is no wasted space inside. I bought this at Home Depot on sale for about $400.00 and it has turned out to be an excellent buy. Delivery was on time, efficient, and people were polite and helpful. Refrigerator was ready to be used about 15 minutes after delivery arrived. I have found Maytag appliances to be extremely reliable and made to last. They have never disappointed me. I will continue to buy them. I highly recommend it.

Sometimes the control panel is difficult to work with especially if the wash is paused to add more clothes or detergent. The good things is that the tub is very large so a comforter can be washed and you can control the amount of water depending on the amount of what is being washed. I also like that it doesnt have the big agitator in the middle.

In December 2010, we purchased our Maytag Quiet Series dishwasher model #MDBM601AWB3, serial #NY2916421. At first the sanitize light quit working about 6 months ago. Today, September 30, 2012, this piece of crap will not turn on at all. There are no lights on at all. We paid almost $600.00. As far as being quiet, oh yes it is quiet alright! We the consumers are demanding a recall. Look at the complaints! Its a manufacturer defect in these control panels. I will not be forced into buying another dishwasher or a control panel. I want this company to stand up and say theyre sorry and fix this problem for all of us Americans!

I spent extra money on a commercial grade Maytag dryer $1300 before taxes because it had a 10 year warranty. The motor and drum quit - and Maytag refuses to honour the warranty. I am appalled by their dishonesty and lack of integrity. I do not recommend them to anyone.

We purchased our Maytag Bravos washer/dryer in January of 2012. In October of 2013, I noticed that the lid would not close properly. In examining the lid, we discovered that the screws were in tact but the information panel on the inside of the lid had come unglued causing the lid to be obstructed from closing properly. After calling Maytag we were told that they make a quality product and, in what I consider to be a condescending reply, could not help us. Replacement of the lid with the service call would cost almost the cost of this expensive washer. So disappointed in what we thought was a wise purchase!

I purchased a Maytag double door refrigerator in 2012. So far the deli drawer has broken 3 times in the same way. There is a plastic peg attached to a side panel on the refrigerator. This pin breaks off after a few months of use. To repair it, you have to replace the entire side panel. The parts and labor costs are about $200 each time. It is obviously a design flaw that Maytag should fix. If you repair it every time it breaks, in about 8 years your repair costs are more than your original purchase price for the refrigerator. Dont buy Maytag products. They are inferior.

Is there any place to give a zero to this Maytag Front Load Washing Machine Model MHW5500FW1 and if there is a class action lawsuit please include us! We have owned other Maytag Washing Machines and never experienced such an epic failure as we have with this washing machine! We were so excited when we purchased our new Maytag washer/dryer set in March of 2018 we even remodeled our pantry/laundry room to accommodate them! As the chief operator of the washing machine, I have literally cried at what a mistake weve made! We have no complaint of the Maytag dryer. Let me describe my new normal procedure for laundering a load of clothes. First, load the washer with clothes then press power/cancel then press rapid wash let the clothes get HOPEFULLY saturated with water then hit hold to start and then hit power/cancel this shuts off the washing machine. I then press power/cancel again and select normal and the water empties out of the washing machine from the prior load and then starts to refill, if the add a garment light comes on (when it wants too) and no I dont change any pre-set settings I am able to add extra water with a pitcher, if this procedure works I let the washer run its 1-hour and 48-minute cycle. If not, I have to start over again because the add garment light wouldnt come on to allow the door to unlock. After the clothes are finished I again press power/cancel then hit rapid wash put my fabric softener in the dispenser press hold to start and let it run its 36-minute cycle making sure my clothes are rinsed appropriately and not stiff because of the lack of water. I neglected to say that when Ive tried tricking the washer and think I am able to add extra water, if Ive added too much the sensing kicks in and the washing machine drains all the water out on its own and refills with the little water it allows! Which is maddening! I throw up my hands and sit down and cry!!! I have contacted Maytag/Whirlpool complaining about the lack of water and their wacky water sensor! I asked them how can you conserve water and electricity when you have to wash your clothes over and over with long wash cycles? This doesnt make sense! My white clothes are now dingy and stiff as well as the colored. Maytag says you can use powdered detergents if its HE High Efficiency powdered detergents, but thats not true. The detergent doesnt dissolve and ends up on the clothes at the end of the long wash cycle because of the lack of water! From the beginning I adjusted the amount of powdered detergent for the front load washer and have to dissolve it in hot water prior to washing and hopefully am able to add it to the clothes if the add a garment will let me! I have now resorted to extra cycles to rinse out any remaining detergent hoping my clothes will be soft and fresh smelling. I had planned to replace my old Maytag agitator washing machine with this piece of junk front loader, fortunately we kept our old washing machine as a back up!

I bought the Maytag Bravo XL washer and dryer several years ago after reading many reviews. I like the glass top of the washing machine and the front door glass on the dryer. The dryer is fine its the washing machine that does not perform like the old machines. Whoever came up with the bright idea of saving water by cutting down the volume in your machine to about 6 inches for a good size load probably have never used a washing machine in their life. It does not get your clothes clean and does not get the soap out of a clothing to my satisfaction. Who made this suggestion? Could it be the same branch of government that made everybody use those spiral light bulbs years ago? The fluorescence that give off loads of EMF?

CWG3600AAS13 - I purchased this advertised as Double Oven. It is NOT - its an oven w/ broiler. The oven shuts off completely during cooking time and comes back on approx. 2-3 mins. This takes place often and loses heat. I have to adjust cooking times and oven temp to make up for the loss. This also happens when broiling. Needless to say it takes MUCH longer to broil anything. When I notified Maytag of this, they responded with it is an open door broiler. Are they serious? I have 2 dogs and 11 grandchildren - burn factor anyone? (P.S. It did not change anything.)

I bought a new Maytag dishwasher 9 months ago from Costco - Maytag 24 in. Built-in Dishwasher with PowerBlast Cycle, White. This dishwasher needs a new motor - Please do not buy this dishwasher. It is garbage.

Because of the power of advertising, we replaced every appliance in our home in 2005 with Maytags. Since then, weve had minor problems with the stove and dryer, many problems with the dishwasher and washing machine, and complete failure of two Maytag microwaves, the last one was only two years old. The washing machine failures resulted in major flood damage two separate times due to two separate failures. Our refrigerator, model MBB2256GEW, has yet to let us down, however, since new it makes loud snapping noises that wake us up at night. It sounds like someone banging two large sticks together. Fortunately, I can repair most of these issues when they arise, but Id much rather get some rest like the Maytag repair man...

The house I purchased came with a washing machine and when I used it the water didn’t pump out leaving me with a load of wet clothes. I went to our local hardware store the same day and purchased the only washing machine they had which was a Maytag high efficiency Top loading washer the same day September 30, 2020. Had the washer delivered and set up, and watched the washer work through the window in the top. The sensor on the machine only gave water up to the top of the clothes, not over them. When it went into the rinse cycle it gave the same amount of water. My clothes came out with soap suds on them and the clothes on top did not agitate down into the machine on the wash nor rinse cycle. Not once on the loads I washed in the two weeks I had the machine did my clothes come out clean and not twisted in a mess making it difficult to get them out of the machine. I used the expensive Tide HP pods and followed the referenced directions. In reading the other reviews on this same washer many of them had the exact same problems that I did. The warranty will not replace this brand new machine nor the hardware store so I am stuck with a washer that doesn’t work as it should and out of the money I paid for it.

We purchased the Maytag dishwasher model # MDB4949SDZ almost one year ago. Since the beginning there has been a smell to our drinking glasses when we put drink in them...smells like boiled eggs. We have always used Cascade dishwasher pods, but suddenly our dishes were being left with a gritty feeling film on them and I had to run them under water to rinse them after taking them out of the dishwasher. This model showed on Lowes website that it has a food grinder, but it cannot even get rid of a single kernel of corn that might get left on a plate. After a load is completely washed and you open the door, there is a strong smell of detergent. If you run an EMPTY dishwasher with NO soap it creates an abundance of suds like there is still soap all in the tub!!The repairman came out and called Maytag and they ran a diagnostic check on it and it said everything was okay. He said to run a cup of white vinegar through it and I did. It didnt help. Still lots of suds being produced when I run a cycle with NO dishes and NO soap!!! He said the food grinder doesnt actually grind or dispose of small particles of food, just grease!! What?!!!! We had to PAY $92 for the service call even though it is still under warranty just because the repairman and the Maytag guy on the phone couldnt figure out why this dishwasher is a hunk of junk!!!! Also, the top rack has clips on the side to lower and raise the rack. The outer sides of the top rack will only hold smaller glasses because these clips get in the way. I hate this dishwasher so much!!! My 18 year old Kenmore ran like a charm until Hurricane Harvey flooded our house. I will never buy a Maytag appliance again!!!

My stove has been reliable and efficient. I bought it about 11 years ago and it looks nearly new. I have a gas range with 2 ovens. The top looks scratched a bit from just cleaning. The only negative is the top which has some scratches if you look closely and when I first got it, I had to have an oven gasket replace. Still I feel it was a good purchase.

Maytag Bravos Automatic Washer 300 - I purchased this washer on July 29, 2010 from HH Gregg. It is less than 3 years old. The washer stopped mid-cycle, did not drain, and displayed the code Ld. The service company recommended by Maytag said that the control panel is defective, and the cost to repair/replace it is over $550 and isnt worth fixing since, he says, these washers are notorious for having problems. Maytag is unwilling to recall this washer despite all of the problems that have been reported. They are unwilling to even admit there is a problem.

Would give them 0 Stars if that was an option. Bought a Maytag washer and dryer in Aug 2021. Washer broke Jan 6 2022. Called Maytag/Whirlpool on Jan 6 as it was still under warranty. They only had one service company in our area to work on the washer. I called them and it took them 10 days to come see what is wrong. Ordered parts. Said it would be 2 weeks. We are now 6 weeks into this with no parts. Called customer service and they said they were notified that their service company needed a part and would take another 21 days to resolve. Talked to a supervisor (Demetrius) who sounded like he did NOT want to be in that position. Offered no solution other than we will just have to wait. Threw a 3 month extension for the warranty on which still does not fix the problem. Sad to see this company go down the tubes as it was once a pretty decent business with solid products. No longer.

We received our new Maytag French door refrigerator today via delivery and got everything set up and magnets stick to the front. The last I checked magnets should not stick to stainless steel. So I called the Menards where we purchased the refrigerator almost 2 1/2 weeks ago and the store manager said there was metal liner under the stainless steel and states this on the technical specifications. And everywhere I went to look under the technical specifications NOWHERE does it state there is a metal liner underneath and even if there was the top is stainless steel regardless so why would magnets stick to it. I paid for a Maytag and basically got a cheap piece of crap Frigidaire or Whirlpool and paid extra for Maytag to stick a Maytag label on it. What a joke. If I have any other problems I will personally deliver this refrigerator to Maytag/whirlpool corporate and put it on the front step. I am VERY ANGRY!!

My $1500 2 yr old Maytag mbf2258Dem refrigerator stopped cooling properly (wont freeze). The icemaker was the slowest I have ever had. That may have been the problem when I bought it. The Maytag Repairman came out and said that even with Maytag sending me a new compressor (under warranty) this unit was not worth fixing. I called Maytag and they said sorry there was nothing they would do. So l looked up every review I could find... and this refrigerator is just bad. Not Worth Fixing. So Maytag deceived me. On the front of the door it says 10 year compressor warranty. Thats a big sales feature! They know that they have a problem. This is one bad company!

We purchased a Maytag Gas range MGR8674AB in November 2012. The contents of the drawer (oven mitts, trivets, hot pads) caught on fire. As we pulled out the drawer, it scorched the front of the range.

Control panel broken for a second time in 23 months: I purchased a Maytag dishwasher less than 2 years ago at Home Depot. 11 months later, the control panel went out. Specifically, the start/cancel buttons stopped working. A service tech called me under warranty; the control panel was shipped to me, and the tech fixed it. He also told me that they had had numerous problems with the control panels.13 months later, the control panel went out; specifically, the start/cancel buttons stopped working (sounds familiar). I can get nothing from Maytag, except a demand for service fees or sales pitches for extended warranties (at a price that was half of what the dishwasher cost new). They also offered me the free part as long as I pay the service call fees. I told them to just to ship me the part and that Id do it myself. Nope. I must pay the repairman. Now, theyll ship me the part if I pay for it, but they wont ship me the free part. It only comes with a service call.Maytag also told me that there were no reports of problems with the start/cancel button, an obvious lie with a quick internet search. The customer service rep sounded like she knew I was getting treated badly and kept using the word policy. Her supervisor was much more cocky and made sure I knew that I wasnt getting anything from her company.They make horrible products, attach what once was a good name, provide zero customer service, and lie to your customers. Great business practices. I will never purchase a Maytag product again.

We bought this washer in February of 2010. We had the pump replaced under warranty in January of 2011, and the pump appeared to have a hole in it from some type of hard object that had gotten inside the pump and damaged it. We then replaced the L-shaped hose between the tank and the pump because it had a small hole in it - very thin rubber. Last week, the washer was leaking again and the service technician said that the pump housing was cracked due to a penny rattling around inside the pump.This washer performs very well when it is working but it seems to be too fragile to handle on normal usage. The Whirlpool washer we replaced with this one ran for 23 years with no problems before it finally went out. From all appearances, it seems that every failure we have had with this washer has been due to damage from foreign objects getting trapped in the pump. Is there no screening mechanism to prevent hard objects from entering the pump? This seems to be a design flaw more than anything.

I just bought this piece of junk... Like everyone else I guess I didnt do enough research! I have had this washer for less than 3 weeks and just like everyone else I am so disappointed in how it tries to wash without water! I too have tried different settings. I had to wash a load 3 times... pausing it while trying to get the rest of the items wet. Its ridiculous... of course now to try and see if I can return it! Yah right... Home Depot does not have a good return policy and Im afraid I will be out 800+ with this washer. This is ridiculous! It really is.

Purchased what was supposed to be a good dishwasher. In less than 3 years the control panel went out. It would cost more to replace the panel than to buy a new dishwasher. I will never buy another Maytag product.

So wife and I purchased a Maytag dishwasher in late 2012. A year and a month later it turns into Hal 9000 from 2001 Space Odyssey. I press normal, it shows light rinse. I press heated dry, it tries turning off the life support and blowing me out the air lock. Finally, in March it dies. No power, no nothing. $500+ for an appliance that lasts 2 years. So for the past few months, while we wavered over buying a new brand or spending $250+ on a repair, we were washing dishes by hand. It was as bad as my grandma used to say it was. Then, by chance I ran across a web blog talking about this being a common problem, and there are hundreds of complaints, and its a problem with a $4.00 part on the control panel that can be fixed with a Q-tip, rubbing alcohol, and silicone... Im not a handyman by any stretch of the imagination, but even this I could do. Unplug or switch off the breaker. After unscrewing all the screws, (not your standard or Phillips head either) unplug the control panel from the control box and remove the control panel. On the back, youll notice a flat cable (pictured below) that will have dark marks on the opposite side of the part sticker. Gently clean this with a Q-tip and rubbing alcohol. I then covered the back (side without sticker) with silicone, (you can get at hardware store or Target) let dry, and put everything back together again and now its working better than new. Im regarded as a master handyman in my house, and I didnt even have to hear the dishwasher sing Daisy Bell as I disconnected it. With such a simple fix, Im amazed Maytag didnt just own up to it and get it addressed. The millions it will end up costing them in the long run, by this frustrating experience shared by us all will have them thinking twice in the future (hopefully). It is a shame they seem to be adopting the business model of American auto manufacturers of the late 80s. Ill update this in a year and a month to let you know how the fix worked, and you owe me a beer for saving you $150 - $600 for a repair or replacement. One word... VICTORIOUS!!

Purchased Maytag Model MVWB865GW0 Ser# **, had it ONE year, circuit board and switch have gone bad, will not turn to change the type of wash cycle and the lid will not lock, which makes the washing machine not start to wash. Contacted Maytag to request a service call, per the service team the circuit board will cost $300, plus a switch $75 and Labor $100 plus tax. We will be better off buying a new washing machine! We should not have this high cost within ONE year of purchasing! Will not purchase a Maytag again!

Bought a brand new Maytag French Door Bottom Mount refrigerator in 2014 to simply upgrade to stainless steel. Put my old refrigerator that I have had for 17 years in the garage. Never EVER had an issue with it and it still runs perfectly. Well, just out of warranty in May of 2015, the ice maker stopped working in the new Maytag. Called and got service. Learned there was a recalled part. Service man fixed. 2 days later, it broke again. They came back out and fixed again. This time, the motor was REALLY LOUD. They came out to replace that. Now, both the freezer and refrigerator are not properly cooling. Cannot keep ice cream and cannot make ice. Called again. I was told these dual fan systems simply do not work. I am out of warranty and too bad for me. A wasted $2500!!!

Dryer wont dry/ service at dead end. So in 2018 we purchased a Maytag Bravos washer/dryer set. The washer does its job, it washes clothes acceptably. The dryer, which has the sole purpose of drying clothes, DOES NOT dry clothes. It leaves each and every load damp. Two to three cycles are required for even the lightest fabrics to dry. This has been the case since the product was new. After repeated attempts to have the dryer replaced, I am fed up with the whole run around. MORAL OF THE STORY IS DO NOT BUY MAYTAG.

The functionality of this machine is so awful. I had the dealer replace it only to find that the awful noises that the machine makes, the fact that the clothes don’t get covered by the water and the clothes are so knotted after the spin cycle you have to untie them is normal for this awful appliance. In the sensing stage the machine groans like a laboring motor around 30 times, then stops with a jolt. My machine is next to the bedrooms and the noise wakes people up. Even in the “deep water” setting, the clothes are not covered by the water. The wash cycle is short and noisy and the spin cycle goes on forever. In the end I have to untie the legs of pants. Whoever designed this machine should be ashamed of herself or himself. Shame on Maytag.

I purchased my 10kg commercial Maytag dryer in March 2015 and started using it in May 2015. Within two months the heater had broken. I contacted the people I bought it off and it turned out I had to contact Whirlpool. It took them 8 weeks to get my dryer going again. The dryer broke down again in November. This time it was a sensor. Again I had to contact Whirlpool, it took them three weeks to get it going again. Being a care home the dryer is essential to our business. We were led to believe when we took out the extended warranty that the dryer would be fixed within a week. I will never purchase a Maytag again or anything to do with Whirlpool.

Maytag dishwasher #MDB 9750AWQ - I am now on the fourth control panel and in less than one year, the present one is starting to fail. The third one failed in less than a year also! I have read the reports of others and apparently, this is not just my dishwasher. Maytag owes its customers a recall of this inferior machine.

MAYTAG BRAVO QUIET SERIES 400 - Do not buy. Piece of junk. I have bought Maytags for years, but they really messed up on these. First I had a new dress in the washer... It ripped it all the way down the back. Last month my dryer went out. It was the heating element. When the Maytag opened up the dryer, all the lint had been going into the dryer casing instead out to the vent. The whole inside of the dryer was packed with lint... It was around the motor and was a major fire hazard. The Maytag man said it was the worst he had seen in his 30 years. This month my washer starts making real loud noises when it spins. Sometimes I have to run it through another spin. Then it just quit. It wont do anything at all. You hear the motor like it is hung... It just hums. You have to unplug it to get it to stop. Maytag repairman said it was the bearings ($300.00 at least) and the computer board had gone out. The repairman said it would cost more than to just go buy a new one. The Maytag repairman himself told me whatever you do, do not buy another Maytag... Now that is sad!!! I grew up with Maytag. My mothers washers lasted at least fifteen years. This is my fourth and last set of Maytags after these!!!

Bought a Maytag Model #MDB8949SAMO dishwasher. After LESS THAN 2 years the motherboard stopped working. Called Maytag to complain, but was told they couldnt do anything. I would give the dishwasher less than a star but the rating system wont allow it.

We purchased a Maytag electric convection oven with a warming drawer 3 months ago. We have been happy with the cooking features, but not the Aqualift self-cleaning. It does not work and Maytag does not acknowledge this. Instead they have offered cleaning products to us which their own instructions tell you not to use! Does this sound like a self-cleaning oven? They have offered to send out a service person to check the temperature. However, from reading multiple reviews by others, there will likely be no satisfaction from this company.

The frontload washer 4000 series began making a very loud noise on spin. I called Maytag and requested service. The technician came and made a diagnostic evaluation, stating this has been a bearing defect affecting several of these models. I called Maytag, and the representative agreed to ship the parts at no charge. A week later, we received the parts, only for the technician to find one of the parts damaged in shipping perhaps. So another part was sent directly to the Maytag dealer. Upon my research, this appears to be a known issue with the Maytag/Whirlpool corporation, and I found where customers had requested Maytag to also be responsible for the service/labor costs, which were also covered by Maytag. I made the call today and was advised no and to be happy that Maytag paid for the parts due to a known defect and that no service or labor charges would be covered. I understand my machine is out of warranty, but this is a known defect; its nothing caused by my self.

We just had the same problem as most of you have posted. The control panel malfunction. Model MDB7749SBM. Our issue started after only 18 months when the dishwasher would start on its own and/or cancel a wash on its own. I think this is a major issue if a home appliance can start on its own from the off position and run through multiple cycles. I think this could be dangerous if you are out of town. Our cost to replace the panel was more than 1/2 of the original purchase price. This is a major defect and should be handled by Maytag if they are a company with any integrity.

Because the design is bad, the refrigerator has to be defrosted once a month. A home filled with Maytag appliances, these are all 4 years old and ready for the trash. Dont buy Maytag, it is crap. They sell for money, not workability. The name has been trashed by Whirlpool. I am a builder and they will not ever see me recommend them, not even to a neighbor I dont like.

We (husband and wife only - no kids) had our Maytag washer for 4.5 years and around year 3, the control panel would need to be reset by unplugging it and plugging it back in. That alone was an inconvenience. This time, the Control Loc light is lit and will not go out despite using all troubleshooting suggestions listed in the guide so the washer is not usable. 10 year warranty covers the drum. I say that is like getting a warranty on tires and when one goes flat, you are told it only covers the hubcap. I can only rate the unit as garbage. Model is 5500, front load. So much for Made in the USA.

Dishwasher Model MDB7749SBM1 - When I returned home from work today, I noticed the cancel drain button was on and the unit was continuing to try and drain but the dishes were not clean and the cascade pod was still inside the unit unused. I then proceeded to run another cycle to clean the dishes and what happened next simply amazed me. I pressed the jet clean button, tough scrub and 2 hour delay button and thought I was all set but the start/resume button would not engage or light up at all and subsequently the cancel/drain button lit up and the unit started draining. Now the control lock and start/resume button just flashes intermittently and wont disengage. I purchased my unit along with several other new Maytag appliances when I renovated my kitchen. I guess the microwave, stove and refrigerator is next -- unit are only 29 months old. Any assistance will be greatly appreciated. Im in deep ish I guess.

We bought this refrigerator one year & 3 months ago & we have had various issues that are now no longer covered under the warranty. The pantry drawer has a peg on the side that is plastic & broke off on the right side. Will have to replace the whole right side panel. One of the door handles is coming loose which should be an easy fix, but its just annoying that it happened at all. Now the control panel is reading OFF/OFF & isnt responding at all. Tried unplugging for 10 secs, then plug it back in, but no luck. I cannot find any info online regarding this issue, so we will have to call Maytag. Hopefully, there is an easy resolution to this problem & we wont have to buy a new motherboard.

This Maytag Centennial with commercial technology washer has ruined a couple of thousand of dollars of clothing, maybe 10 to 12 of my favorite shirts (ripped holes around the top of the pockets), bath towels and sheets and comforters and hand knitted small blankets that can never be replaced. It tore holes in nearly everything that was made out of cotton, I was doing spring cleaning and I normally wash most of my summer clothing, but this time this washing machine destroyed nearly all my summer clothing. This washing machine came with the house I just purchased. (I gave my older Maytag washer and dryer to some needy folks which worked great when I moved here). Disappointed in MAYTAG. Will never buy another Maytag!

This washer came with the home we recently purchased. I used the machine and OMG the spin cycle is NOT quiet.. I posted a video of it on FB. A friend of mine who owns and operates an appliance center watched it.. messaged me back and said Do not call repair man as it is cheaper to buy a new machine... I knew this machine sounded like a piece of **.. I know I wont replace with the same machine.

Bought a Maytag fridge model MFI2569YEM0 a few years ago. From the get-go, the ice machine would spit out ice hither and thither, mostly not into the cup or mug. Even when I held the cup up high into the dispenser orifice, I noticed it still spit out ice seconds after I released the cup, so ice cubes would spill onto the floor. Secondly, the vertical doors do not close well, and I must manually push them closed, especially the left door due to the poor design. (I noticed my neighbors more updated fridge has a better closing door. Forgot what brand, though.) Theres also rust forming on the front of the stainless steel fridge panel. It has penetrated through so I am unable to remove it.Lastly, this past week I walked into the kitchen stepping in a pool of water in front of the fridge. There was a sheet of ice accumulated on the bottom of the freezer. After some research, its likely the nipple in the back of the fridge that plugged up. I have yet to fix the problem, but so far, Maytag gets an F- in quality, and I will NEVER, EVER purchase any of their appliances again. I remember my parents washer dryer lasting 30+ years. Maytag, what happened???!!!

I bought my Maytag Bravos washer and dryer set about 3.5 years ago when I moved into my home. There was a 20-year old set here that did work, but I wanted something newer and more efficient, so I donated the old set and bought these. Performance of the washer has always seemed mediocre, clothes dont get as clean as I think they should, whites are dingy, despite using hard-water additives and the correct HE products.A few months ago, the washer started a new behavior: stopping during the initial fill cycle and displaying an F1 error. I soon figured out if I hit cancel then start again, it would resume filling and proceed with the cycle. Over time, I had to repeat it more and more. Its now up to ten F1 errors both at the beginning and end of the cycle. I dont have that kind of time to babysit my washer. I already have a full-time job.I have called Maytag/Whirlpool twice now, both times getting unsatisfactory answers. Even after escalating to the customer service supervisor, I was basically told that it is most likely the control board that is the problem and since Im no longer under warranty (that washer ‘is’ almost 4 years old, maam), Id either have to order the part myself from their supplier (total cost $250 + the risk of DIY), or buy their service package for about $350 which included fixing that problem plus one additional years warranty.I pointed out that for a major household appliance that I (over) paid for, I expect a life of more than 4 years, especially since I had a working 20-year old washer when I moved in here. Since when is this acceptable? I could understand if it were a wear-and-tear part, like a rubber seal or something that moved constantly and would eventually need replaced. But this is the electronics module, something that cant (or at least, shouldnt) be worn down or broken by use or even user error. This is an integral part of the machine, and if it has a fault (which it clearly does), the manufacturer needs to stand behind it and help the consumer.What angered me even further is that the customer service manager even admitted that models similar to mine had had similar problems, and a free control board was sent to those customers. But my model was not in that range of production, so clearly they have no fault, in their eyes. Apparently, its not even remotely possible that maybe when they determined the range of models they believed to be faulty, mine hadnt been in use long enough to display the same behavior? Maybe the range they selected is too restrictive and they missed some. From the volume of complaints Ive seen online, Id bet that to be the case.I asked to be transferred to their legal department, and was refused because we just dont transfer customers to the legal department. Well, I just dont buy Maytag or Whirlpool anymore, and Im going to do my best to make sure nobody else does either. Im replacing this ** with a different brand, one Ill be sure has tremendous reviews and a manufacturer that will stand behind it.

We have had our Maytag double oven for about 5 years. 18 months ago two of the burner knobs froze off. You cannot turn them. We had oven repaired - they replaced part WPW 10204705 - it cost us approx. $400 to repair. Here we are today and ANOTHER burner know has frozen in the off position. I will have to pay again to have this repaired. We are super disappointed with this over and with Maytag. We would never purchase from them again.

I purchased Maytag French door stainless fridge 5 years ago for $2200. The doors were out of alignment and I put in new control board; both items almost right away. Then in May 2011, we had to replace another control board for about $400. Then in July 2011, the compressor went out at a cost of $300 for the compressor, $350 for labor. I called to Maytag, Gwen agreed to pay for the compressor but not the labor to put it in. So we now have about $1400 invested in our $2200 refrigerator. Letters to Maytag CEO Mr. Fettig remain unanswered. Do not buy a Maytag appliance!

I just bought my first home and after well over 20 years of apartment living and not having my own washer & dryer I was so excited to finally be able to buy one! I decided on the Maytag/Bravos and even spent the extra $100 for the glass top. The high efficiency machine was delivered on August 8, 2016. My kids are grown so its just me; I do one load a week give or take. A week or so ago, I noticed the washer was taking an inordinate amount of time to go from sensing to washing and even longer to get into the washing cycle. This past weekend, it didnt work at all. Just sat for hours with the sensing and washing lights on, without actually washing the clothes. The machine was packed loosely with the correct amount of High Efficiency Detergent in the proper place. I called the #Sears store I purchased the appliance from (Braintree Ma.) and they said there was nothing they could do as it was past 30 days, gave me their customer solutions number which is basically a call center with people who I could barely hear and/or understand. They in turn gave me more phone numbers which seemed to me to be in the same call center. I want to return the 4 month old washing machine that doesnt work and I want my money back. Ive filed a report with the Massachusetts Attorney General Consumer Affairs Department. I will NEVER AGAIN shop at #Sears and I will NEVER AGAIN purchase a #Maytag appliance. I am beyond disappointed in #Sears and #Maytag, both names that used to mean quality and customer service. And if theres a class action lawsuit to be filed, please count me in.

I bought the power wash Bravos XL... Bad. It does not rinse the clothes, leaves residue on dark clothes.. probably all clothes - cant tell on lighter colors. I dont recommend!!! Waste of money.

Just a year after purchase, this Maytag Bravos Washer stopped spinning the clothes. It never washed worth a damn anyway. I paid extra money for a quality product from a known brand name and I was taken to the cleaners. Never buy a Maytag product unless you want to replace it in a year.

I would not recommend the Maytag washer with the large tub. It does not clean your clothes. I called Maytag and they do not care as long as it uses as little water as possible! Not a good value for the money!! That was the first time and last time I buy a Maytag... Thats the last $5000 they will get from us!

No motor is available for the Bravos washer machine which is 5 years old! Now the machine is garbage and I need to buy a new one. I thought Maytag was a great brand so I purchased the Bravos but now I understand from the company that no motor replacements are available!! Wtf? Maytag/Whirlpool dont care for loyal supporters so, I am TELLING EVERYONE not to purchase Maytag/Whirlpool appliances whose name has gone for a dump with this latest situation.

Purchased this oven at Lowes on 2/8/2018 for $1925. Worked good until my wife cleaned the lower oven on 11/22/2019. The next morning the oven was locked and nothing would work. We called for service and the repair bill was $194.55. I told the repairman that the oven had a 10 year warranty on it, one year on everything and the rest on the parts only. He said no, and showed me in the warranty book that it only covered two parts. Which was not the two parts he had to replace. If you purchase a oven with self-clean feature, I would recommend that you do not use it.

This washer sucks so bad. Just got it a few hours ago and its absolutely horrible. The water just runs for the wash cycle. And I was told by the salesperson at Best Buy that it would save you water. Thats not the case. There is enough water to run over all the clothes. It doesnt agitate enough to even move the clothes around. The clothes basically sit at the bottom of the tub in the water doing nothing. This Maytag Bravo washer will be returned tomorrow. Me and my wife are highly disappointed. I wouldnt recommend this to anyone. Weve decided to just get the old washer fixed and go from there. There are too many bad reviews for this washer to still be on the market. We feel that this was a total waste of time, energy and money.

I have an MFD2560HEB refrigerator that I purchased 6 years ago. I paid a premium price for what I thought was a quality product. It has had issues with the ice maker from the beginning, yet I was always able to get it fixed with unplugging the unit for a while. The fan inside the unit stopped working last year. I took apart the entire inside to replace it, and now, 4 months later, the water is completely frozen. Unfortunately, I purchased a Maytag induction stove in May and less than a month later, it is not working either. Maytag quality is not! I asked if I could return the stove, but was told I had to let them fix it. Im still waiting to use my $2,000 stove!

Control Panel MDB8949SBB - I purchased my dishwasher in August of 2013. The control panel has stopped working and Maytag refuses to discuss the issue with us. Regardless of how many complaints they receive they are in denial about their product. They now offer a Repair +1 program which costs $260 for a repair and an additional 1 year warranty. If I do that I will get 1 year out of it before I run into the same problems. Any ideas?

Purchased a new Maytag dishwasher three years ago. After having it for one year the panel box no longer worked. Had to pay $300.00 to repair. Now half way through washing the dishes again no water will go into the machine. Only the first part of the cycle. I am sure it is going to be the panel box after reading other peoples problems with this machine. I will not pay to have it fixed this time. I will have to buy a new dishwasher. I will never purchase a Maytag product ever again. I have lived in my home for 40 years and never had a problem with any appliances. This would have been my third dishwasher in 40 years and as you can see it has not even lasted 4 years. I will inform my friends to stay away from Maytag.

We purchased our double free standing gas range about 6 years ago. Our top oven went out about 4 years after purchase. We purchased the extended warranty from Sears and it was fixed at no charge. About a year later, the top oven would not work again. We called Sears, our warranty was up so it would be a repair that we would have to pay for. We decided to go with the Maytag repair service since it is a Maytag appliance and we had to pay anyway. The repairman came in and said that the top box that holds the electronic in it had fried wires and it would have to be replaced. So for $480, he could replace it. It was more than likely caused by a power surge. I just read that this also coincidentally happened to someone else so I find this cause to ask more questions. I also note that the top of the oven behind the burners where there is some sort of vent gets extremely hot (I accidentally touched it and had a blister the next day) when the oven is being operated. This is directly under the box that holds the electronic components. I would think that may have something to do with the wires frying since it is that hot directly below the panel. Could this be a defect in the building of the stove? Has anyone else had this instance beside the one person that I read about on your website?

I bought this Centennial washer about 7 weeks ago and it has worked right for 4 of those weeks. The washer wouldnt spin the clothes and they came out soaked. Service guy came out and said it was the computer panel and he didnt have one. So I waited over a week for another service call. He put that one and said that now the transmission was shot and he didnt have one, another wait. This is a piece of junk. Do not buy Maytag or Whirlpool products. I had a Maytag for 15 years and had one service call. They are not what they used to be.