I have had a few dishwashers in the past, however this is the worst product I have ever purchased. After a couple of years in service I needed a new control panel which cost $200.00. The dishwasher defaults to heated dry and the exhaust for the dishwasher is right behind the copper electrical runs so it corrodes and fries the runs. The way I see it Whirlpool and Maytag saw a unique way to gouge its customers for parts. They also have a rope and plastic cable system that attaches to the door spring that continues to break cost $28.00 a piece, I have replaced two. Now I see that one of the pulley guides (plastic) is broken and split cost??? Here is another brilliant engineering feat, the door panel clips into the control panel so that when the door is pulled in a normal fashion it comes loose. If you buy this line of dishwasher (p.o.s) plan to work on it and buy parts on a constant basis. Here is my advice: buy one control panel, two cable systems, and a couple of cable pulleys or buy a cheap dishwasher as a replacement and save some money. Run from Maytag or its parent company Whirlpool - let the buyer beware.

After reading several of the reviews, it looks like Maytag doesnt get it - or maybe they do and its a plot to make more money. Our dishwasher model MDB8959FSZ4 was installed in Dec. 2016. Within the year, it started leaking. After many service calls it was determined that the arms holding the upper rack were not installed properly and were pushing against the door and water was coming out. After that was replaced, weve had 2 years of relative good use. Now, it wont empty and that started after smelling something burning. The burning smell has gone away but it wont complete a cycle. Service tells us its the drainage pump and that will cost nearly $500 to replace. We wont be spending another dime on this piece of crap. Well replace it with NOT A MAYTAG. Im wondering if it has to do with the control panel as many others have mentioned. We dont care to find out at this point. We are buying something else.

I bought this range (Gemini Double gas range) in 2010 but was not installed in my house until 2011 due to time delays in kitchen re-model. I paid $1310.00. It was serviced 3 times once under warranty. About a year ago the igniter went in one of the ovens for the second time and one of the stove burners wouldnt light. Since the other oven and 3 other burners worked we didnt call for repair, then a second burner stopped working and we called our Maytag dealer. 2 different service techs came one with more experience and both said the same thing the stove wasnt worth fixing due to cost of parts. One of the problems was the screws in the burners couldnt be removed due to rust and deterioration of the screws. They would break and cost other components also to be needed. So after 7 years of use and already having repairs done I have to buy a new stove. It will not be a Maytag. I also bought a top of the line Maytag dishwasher and one month past the 5 year warranty the electronic panel burned out. After calling Maytag and complaining they did agree to pay for the part close to $300 but I still paid for labor. When I looked at reviews for the oven before purchasing they werent too good but wanted a double oven at the time and always had good luck with Maytag in the past. I thought buying a higher priced model would be better quality. Not so. After calling Maytag today the best they could offer was to buy an extended warranty for $380, I declined. My advice - Listen to the reviews. The Maytag repairman isnt sitting around idly anymore!

We purchased a new Maytag dishwasher last year when we purchased our new home. All the other appliances were Whirlpool. This dishwasher runs forever. We have huge electric bills and I am sure this is a contributing factor. We purchased it from Lowes. They have sent out two technicians who say there is nothing wrong with it. One said it was because it was in an island. The other that our water is not hot enough. He turned the water heat up and now you have to warn people using it to be careful or they will get burned. No wonder the Maytag repairman is so bored. He knows the appliances he services are junk and doesnt bother. Take my advice. Buy ANYTHING BUT Maytag!

Purchased a Bravo set 5 years ago. Paid $730. For the washer. 4 repairs in 5 years. It is now has a bearing out and that will cost $450. MAYTAG used to be the best... buyer beware!

I had a tub failure on my washer Whirlpool Duet, which I bought brand new and it lasted 12 years with no problems. The dryer is still in use at my sons house. However, this failure lead me on a search for a set to replace the duet. I did some research and found the Maytag 6.2 Cu. Ft top loader and huge Dryer to match. The set was not cheap and it did have high marks for a great washer. So, I bought them both and had them delivered on 12/30/16. I have read all the owners manual and watched YouTube videos to see how to use this machine with all its pretty lights and sounds. I will concede that the machines look great, very impressive in my laundry room. I would bet it would even be a plus when I go to sell the house.THAT is all the nice stuff I can say. The machine does not clean clothes and I have done all the settings. I have changed laundry detergents, and even tried to add a little more water with a bucket at the start of the wash. (Saw that one on YouTube.) REALLY. That did not work, nor should I have to do that to get it to clean well. The answer seems to be, set the machine on FULL tub of water. So, I tried that for a couple of times and found that the clothes just float around and since they do not touch the Wear Plate they dont get clean. My wife (yes, I am a man that does most of the laundry) said she hates the washer and I was an idiot for buying this expensive piece of metal that does nothing but take up space and leaves spots on your clothes. Have you heard the term Happy Wife-Happy Life. Well not so much for me now.Spending money even $2,500.00 on a washer and dryer seems a little crazy. But I had the extra money and I have always wanted a MAYTAG. These guys know how to make a washer. Boy was I wrong, this machine must be an embarrassment to Maytag. I know I am really shocked that you would sell this machine as top of the line. I am not sure what Maytag will do, but I thought I would give you a chance to make this right. I have attached pictures of the machines installed and pictures of the model number plates. I have faith that Maytag will step up. My wife said this was a waste of time. The ball is in your court Maytag. (Come on Maytag let me win this one.) - Just a man and his dirty clothes.

I bought a Maytag Dryer from Lowes in December of 2013. I paid 600.00 for this dryer which I thought was going to last for quite awhile. It stopped working in January of 2016. (2 years old). I had a repairman come out and he said the motor had burned out and he wanted 300.00 to fix it. I called Lowes and asked if I should expect the motor to burn out in 2 years; they said of course not - call Maytag. That proved to be a complete waste of time. They would do nothing. They simply said that there was not a recall on that machine and they were not technicians. However they would be glad to send someone for 125.00 dollars to look at it, then the parts and labor would be more. I have never had a dryer burn out in 2 years - not even when I was raising children and using a dryer daily. This Maytag clothes dryer isnt even used every week and when it is used, there are a few small loads. I am appalled and disappointed in Maytag and the poor quality of this appliance as well as their horrible customer service.

Within the first month of purchasing my front loading Maytag Neptune washer (MAH6700AWW) at Home Depot, the soap dispenser fell off. The machine not only leaked, requiring stack of towels to be placed on the floor to keep the room from flooding, but often produced foul-smelling clothes, despite cleaning the machine. On top of that, the delicate cycle stopped working and then last month, the entire control board went! It is past its warranty period, and I cannot afford a new washer for my family of 6. The machine has been discontinued and the parts unattainable. The control board of our dryer (MDE6700AYW) went too, causing buzzing in the electrical connection and burning, causing us to have to shut down the circuits for the machine. Maytag has lost all my respect as a quality appliance supplier. We spent $1700 on the set and the machines have been a nightmare. Please note: we were NOT notified that there were class action suits against Maytag regarding their machines.

I paid a lot of money for this washer. It was recommended by a service guy from Sears. It is only 3 years old. I dont think it cleans well at all. Energy efficiency? Not seen on this machine at all. It takes at least an hour for a cycle. It is super loud on the spin cycle. Now it is leaking and has that stagnant odor that front loaders get. Really! Waste of money. Will never buy a Maytag again.

We purchased a Maytag Bravos washer & dryer in September 2012 and 2 1/2 years later March 2015, no heat. We called a repairman and he said heat element went out. When researching this problem online I was shocked how many people had the same problem as we have. It cost over $300 to fix and I am concerned that it will just break again and again after reading these reviews. I think that a class action lawsuit may be needed so that this unfortunate situation does not continue to happen to other consumers.

After everything posted here why would anyone take a chance buying any Whirlpool product including all subsidiaries. I made the mistake of buying a Maytag washer and dryer less than 3 yrs ago. There are only 2 people in the household and we only wash linens, towels and undergarments- the rest goes for dry cleaning. The washer stopped filling with water, similar to what was posted by another customer. Maytag customer service was 2 weeks out.When the service tech arrived he diagnosed the problem as a faulty water value but didn’t have the part- another week. I asked the tech why it takes 2 weeks to get someone out for a service call- he told me that there were 4 techs working the area but 2 quit and they were never replaced. The tech went on to say that he was leaving because of the misdirected grief he gets from customers because “the Whirlpool brand is crap”, it takes to long to get service and usually the cost is more than the appliance is worth- and they take it out on him. That is not hard to understand.Bottom line- IF THE SERVICE TECH IS TELLING YOU THE BRAND IS “CRAP” what else do you need to know. FYI- Maytag repairman quoted a new water valve at $70, labor $150 for a total of $230. I paid $600 for the machine- is this a joke? The exact same part was available on Amazon for $43 and was delivered in a day. With the help of a YouTube video I replaced the part in 10mins. On top of the fact that the appliance is crap, it would have taken 3 weeks to get fixed- Maytag is also screwing customers with overpriced parts that shouldn’t have to be replaced in the first place- fair warning, STAY AWAY.

I purchased this washer three years ago. It worked fine, but all of a sudden the washer stopped spinning and was not following any of the cycles. Of course it was out of warranty. The repairman states the computer board on the washer is fried and will cost $400 to replace. Several stores have stopped selling Maytag because of quality issues. No more Maytag for me.

I have used several brands of refrigerators and Maytag stood out for me. Everything works as good as new. However, my experience with ice machines, has been the first thing to quit.

Duck bill valve for defrost water from freezer malfunctions, water flows into freezer freezes, then eventually overflows onto floor. Huge problem for folks with wood floors. Also a slip/fall danger especially for the elderly. When the repair line is contacted, they deny the problem and say you are the only one. But if you do your research, you find there are hundreds of complaints and in November 2013 they issue a service bulletin, but its internal, not meant for consumers to find out. So if you have this problem, go to the Consumer Product Safety Commission and fill out a complaint. Maybe then something may come of it.

Maytag washer manufacture changes are not worth a dime. I suspect EPA made the changes, and engineering was made by someone that has never washed a load of clothes in the entire life. There is no agitator and/or supposedly made to conserve water. Well, it saves water alright with each load. There will be a 2 foot circle in the middle of a bed sheet that doesnt get wet; the same with a sweaters. I have checked with different stores and all made the same. And heaven forbid if you dropped a sock and wanted to add it to the load with the mate. The lid locks. I am both angry and dissatisfied and will tell this same story to anyone wanting to purchase a washing machine.

I am a WWII vet. I bought a Maytag dishwasher 4 years ago from Home Depot... Cost me $600 in total repairs. Maytag would not help. My son just brought it to the dump! At that same time I bought a Maytag bottom freezer from Home Depot... It has never worked right. Ice dispenser broken after 1 year, food freezing in fridge at any temperature... It just died! Maytag refuses to take any responsibility for THIS POS!They should be ashamed at the way they treated me. I am 94 years old, and have fought for our freedom, and was looking for one simple thing from this American company. Its called fairness! Maytag sucks! You have lost a lifetime customer. You have lost my son as a customer, and will lose anyone I talk to, as well as my son posting on ALL social media! SHAME ON YOU MAYTAG! SHAME ON YOU MAYTAG!

The washer is so loud it can be heard all over my home (my home is 2700 sq.). It sounds like metal to metal grinding. I was told thats how the run and the first bit of water isnt enough to even wet the clothes. Id never buy another one (even though this is my 3rd Maytag washer. Im 78 yrs.old).

I have owned three different Maytag washer/dryer sets. The reason for so many? Selling the set with the house upon moving. I kept my last set which is Bravo. I love Maytag for their features, their dependability, their reputation. I have never had repairs on any of them. Totally awesome! My second set had a neat feature of a drying rack where you could place a sweater or shoes and no tumbling. Sorry I sold that set w/ the house. I am very pleased w/ my present set of Bravo. No agitator. A coworker also bought this set. Maytag is the best!

Maytag Bravos electric steam dryer purchased 2009 - I have had to replace the door hinges within one year of usage at my expense. The blower belt and pulley had come off twice, the last time about a half hour after the repairman (again at my expense) left. I put it back on myself and if it comes off again, I will use Locktite to glue it on the blower shaft. I figure I will be lucky if this crap lasts a couple more years anyway. No more Maytag for us! What does it take for the consumer to get some representation with regard to lemon laws here? I will take my wrath out on Home Depot here since I have no recourse. If enough people complain, maybe they will stop selling that junk. I also will disregard Consumer Reports in the future.

Had a Maytag Dishwasher that was recalled in 2007 model # DWU9962AAE. I was sent a notice of recall and when I contacted the Maytag staff in the Recall department said that they were sending out a replacement as the unit. Mine was being recalled due to defects in the heater element, which could cause electrical failure and fire. I was pleased they were offering to replace the unit, and within a week or so, a new unit was delivered. This is where the troubles began... the delivery/install person from a local retailer, complained the entire time about having to do this job, was ill-equipped to perform the install, twice he thought he would have to stop as he did not have the correct tools he shared with me. I felt this was odd, if this is the job he did all the time? I asked for a bill of sale or something that would show that this unit had a warranty, and date of install. I was told that in these cases, the local retailer that is contracted to install takes care of all that. I did get the Dishwasher use and care guide, and it seemed like new unit. I had never had a recalled unit of a major appliance. Also since Maytag had my address, phone and email information as they set the install up. I believed the installer. Fast forward to about 2009 and the control panel on the door starts to lose cycles. I decided that since it was just me using the unit and the cycles I used most worked I would not bother with the repair.Fast forward to late October of this year 2015. The dishwasher Maytag model # MDB9601AWW finally does not turn on any longer... I call Sears to have an estimate for repair of the circuit board in the door. I give Sears the model and serial number... and schedule an appointment. The repairman gives me a cost of roughly $600 to replace the circuit board in the door! I tell him no thanks pay $ 59.00 and decide I will buy a new unit... I review many sources such as consumer reports, where it becomes evident that Maytag as a brand is not very reliable. At that point I decide to call Maytag and speak to them about my issues. Two dishwashers in very short order have issues. Also my new unit only had a one year warranty.So much to my surprise when I called Maytag I was informed they did not have any records of my contact information at my current address..? And worse there was a recall on my current dishwasher back in 2010! I was never informed of this, and had used a potentially hazardous appliance for 5 years with no knowledge of this! How could that be though since I was given my current unit by them in 2007. I was very unhappy at this point.... but my disappointment with Maytag was about to deepen.I was also not happy with Sears Home Repair.... They are informed about all product recalls, and had my model and serial number. When those were entered into their computers when I made the appointment and again when the repairman came out and captured that information on my dishwasher himself that should have alerted him to the recall. Not an opportunity to sell me a $ 600 repair that did not even address the defect for the which the recall was issued.So I am now routed to the Maytag recall department.... where all they offer me is a $ 150 coupon for an expensive Maytag dishwasher? So after explaining my situation... and asking the woman I was on the phone with If she would invest $400 or 500 more dollars in Maytag dishwashers, given my experience with 3 failures of their products in two separate units that were not that old? She said she understood. She arranged for her manager Carol to call me the next day at 9:00 am PST. The call never came, and two hours later when I called in they tried to tell me it would be another 24-48 hours before she could return my call? I was now very unhappy. I asked to speak with her supervisor Tim. He too was unavailable, finally after a very long time waiting on hold. I was connected with Amber. I explained again my issues and told Amber that I would like another Maytag Dishwasher to be offered to me..... as this was a very unique set of circumstances... She was willing to let me write letters like this and contact the Consumer Products Safety Commission and lodge a complaint. I am waiting to be contacted by the manager that handles recalls from Maytag. She alleged that they CPSC does not allow the Mfg to assign specific compensation to individuals. That is true....when they are only subject to one failure as part of the recall.... according to the woman I spoke with at the CPSC. However I had not only that complaint; but the circuit board issue and as goodwill gesture to any consumer they (CPSC) have no jurisdiction.... and Maytag could do as they wish. However I doubt anyone but Amber a low level manager, who took it upon herself to make this decision on her own, without even punting to her boss Tim when I shared my story. I just this last weekend bought a new Bosch dishwasher.... and would caution anyone who was considering the purchase of any Maytag appliance of any kind to use my experience as a cautionary tale.

Ive had my Maytag (above range model) for about 4 months. The same as everyone else with open/close door error. Faulty door switch. When the interior light doesnt come on, I know I will get the error. You would think Maytag would have already repaired or replaced this door switch part.

We purchased both a new Maytag washer & dryer in 2011. Our dryer, Model #7000XG1 all of the sudden started thumping when we were drying our laundry. After we called a technician to come out, he stated we had a crack in our drum. How in the heck does that happen in 4 years time and only laundering for 2 people? Of course this steel drum should not wear out before the other parts, but it did. Since there is a backorder on the replacement drum, it makes you wonder if this problem is wider than it seems. Also, Maytag would do nothing for us other than offer us the purchase of a new dryer at a discounted rate good for only 7 days of their offer. Seriously, how about standing behind your product? And, then again, why would we be enticed to spend that kind of money on the same type of product that has flaws? Uh, duh Maytag or Whirlpool. Silly fools you are.

Our current dishwasher was already installed when we purchased this house. It is adequate, however, it does not do a great job with caked-on food. This means that the worst dishes need to be pre-cleaned.

My husband and I bought a Maytag Bravos HE washing machine 3 years ago at Home Depot. It is by far the WORST appliance purchase we have ever made in 40 years! This machine started making horrible grinding noises about 6 months. It is not rinsing properly and its leaving detergent stains on our clothing. This washer needs to be recalled. I will NEVER buy another Maytag product, EVER!

Never waste your money and buy Maytag washer. Mine is XL large tub and has extra wash for extra clean. Dont waste your money. Never fills up with enough water. Almost everytime I wash I have to rewash the load because the clothes are still dirty, have soap spots and most of the time the clothes didnt even get wet. Horrible Horrible washer!!! My water bill has gone up a lot because I have to rewash the load so thats twice... I cant even use the XL tub because it wont fill up with water. Horrible product. Cant believe Maytag is still in business. They dont stand behind product. Called. Complained. They gave me nothing except for some free pods to clean a washer thats only 6 months old. Ive tried every cycle to see which one will wash the best. Still Horrible Horrible. Doesnt get anything cleaned. Here I thought nothing could get worse than a front loader? Well the Maytag is worse Horrible product. Dont buy. Dont waste your money. Try another brand!!!

Maytag MHW3505FW Washer and dryer were purchased 13 months ago. I purchased and spent $2,000 because the Lowes salesperson and the stickers on the machine said they had a 10 year GUARANTEE AND commercial quality/technology. Exactly 2 weeks after 12 months the washer started flashing erratically when I was able to turn it on. Wouldnt react to any of the touch controls and stopped working. Called Lowes who told me because I hadnt bought an extended warranty they would do nothing. When I told them I was told a 10 year warranty was in place they said they only cover a year. I was told to call Maytag. Maytag said the 10 year warranty only covers the steel drum and motor! Nothing else is covered after one year. I was offered an extended warranty for $600. Not something I will be doing. I will replace with non-computer washer and dryer and will NEVER BUY MAYTAG again. They should be sued for false advertising.

We bought our front load washer and dryer about 5 years ago and have had no problems with either. We also purchased a Maytag French door refrigerator 2 months ago to replace our Sears Elite brand when its compressor went out after 27 months (Ill never buy another Sears appliance).

My Husband bought a Maytag Bravos Washer 2 years ago this next month. The washer is extremely hard on clothes. We have to wash all clothes on hand wash to keep them from tearing up our clothes, and we are having to replace the door lock for the third time. Of course the last 2 times were not under warranty. So once again, I cant do laundry when I need to. Thanks.

Our washing machine is 3 years old. About a year ago we started to see hairline cracks on the plastic lid in the bottom corners by the hinges. These have now become huge and pieces of plastic are breaking off every time we do a load of laundry. Maytag (under the Whirlpool brand) will not replace the lid for us. We paid $130 for a tech to come out and confirm what we already knew - that we need a new lid. And now the parts and labor will cost over $550. We have called customer service several times and spoken to a supervisor and the best they can offer us is to pay for the part which still leaves us to pay over $400 out of pocket to repair a $600 washing machine. This seems to be a common problem and is all over Google, yet Maytag is not willing to help their customers.

I bought a Neptune Washer in 1999. 6 years later (2005), it started making the 747 landing noise. It was implied that somehow it was our fault, maybe, something from my contractor husbands pocket. After all, it was a Maytag, and surely there could be no design or engineering flaw! (My daughter still has 34-yr.old one.) We were told the repairs would be so expensive. It would be wiser to buy a new one. Foolish me, I bought another Neptune to match my dryer. Of course, now this one has the same bearing problem and again its cheaper to buy a new washer. I am angry and not sure how to proceed. Any washer, but especially a Maytag, should last more than 5 - 6 years. I should not have to buy my 3rd washer in 12 years. And if I do, it certainly wont be a Maytag!

This machine (Top-Loading High Efficiency MVWB755DWO) does not clean, it only leaves soap and moldy residue on clothes. The Whirlpool company refuses to assist even though it was delivered less than a year ago. So much for warranties! Wrinkles clothes, wrings incorrectly and does not give you freedom to manage independent of technological controls.

I purchased the top load Maytag Commercial Residential washer with an agitator last month. I wanted a basic washer with Hot/Warm/Cold settings, Delicate/Normal/Heavy Duty cycles, Small/Medium/Large loads. I paid over $800 for this washer and I cannot wash my whites or rags in hot water! The hot water setting dispenses hot water, then cold water, back and forth. The end result is cool water. Ive called Maytag, Ive been told that there is nothing that can be done about it, thats how theyre made to be considered HE. I asked them why they even put a hot or warm water setting on the washer.You have no control over the water level, all cycles except for normal run in a deep water setting (full drum of water), I dont know why delicates are in a deep water setting. I only wash a couple pieces of delicates together. I end up using a lot more water and detergent with this washer. I hope we dont have to conserve water in the next few years! So though this washer uses less hot water energy, it wastes a lot of water, my water bill goes up and my detergent is used up much quicker! I cannot add time to my wash cycle, (the actual washing/agitation cycle is very short - 10 minutes) it has to drain all of the water and re-start the cycle with more water! $800 is a lot of money for a washer that doesnt wash like my old cheap washer. The local store cant do anything about it and Maytag brushed me off.

Our first (and last) experience buying anything made by Whirlpool. I bought a matching Maytag Series 2000 washer and dryer in February 2011. By July, the washer was at 747 take-off noise level when hitting the spin cycle. I called Whirlpool, who directed me to their local repair firm. I called them on August 2nd and had a service rep visit on August 9th. He looked a 30-second look and advised that the bearing assembly was shot and that the spin basket required replacing.

Im really happy with my range. The only drawback is that the upper oven/broiler is a little on the small side. The five burners on top are convenient for when I am cooking a large family meal on weekends and holidays.

The steam/heat produced by the oven has made the electronic (digital) control panel buckle. Yes! This is a thousand-dollar (plus) stove, and it has warped, through no fault of mine. When I want to cook something, I press the keypad to enter the number of cooking degrees that I want. The problem is, the control board is not working correctly. Regardless of my typing in 350, it will default to 100 degrees and stay at 100.As a teacher, I do not have a huge income. I was disgusted with my recent repair estimate of $80 for a service call, and a quote of over $600 for the replacement part, plus some not-yet-determined labor installation costs. Calling the 800 phone number for Maytag connected me to some local people working as independent and overpriced contractors in Los Angeles, California. They are not MAYTAG employees, so they are not well-informed about the product.I miss the time when manufacturers stood by their products, and had factory-trained and authorized employees available to make repairs. I bought this monster Maytag stove from Lowes. I am disgusted with both companies. I have gone online to research buying my own part and hiring a local yokel to put it in. Most everyone I have encountered has been a rip-off artist. I am teaching your kids and grand kids to read and write, and you dont want to help me repair my stove without price-gouging. I can use the burners to some stove-top cooking. Life has become a hassle without being able to cook.

I purchased a Maytag Bravos washer and dryer pair in 2009. Over those 5 years I have had at least 8 shirts come out of the washer with tears in the armpits. First I thought it was my armpits destroying the cloth. Then I thought it was cheap cotton (all my shirts are 100% cotton) from foreign manufacturers. Ive had two shirts destroyed this week, this mornings was really thick material. Usually when I remove clothes from the washer, they are entwined and twisted. Consistently when I wash any load including a towel or two, the washer becomes unbalanced. My clothes often have a foul odor after washing. My theory is that the lack of a center agitating spindle is allowing the clothes to tangle, and not really cleaning them. I have to use the extra rinse setting or the clothes come out covered with soap suds. In summary, Im not happy with this washer and will never buy another Maytag appliance. Im also not sure the high-efficiency technology has had all the kinks ironed out.

After only three years of gentle use, my Maytag front loading washer bearing went. The repairman said this was because of too much detergent and the repair bill would be over $1100.00 (more than the cost of a new machine). I would never buy this machine again.

First, the machine is a wrinkle monster no matter what I try. I wash my clothes on delicate cycle to keep the colors longer and so my clothes last longer. This has never been a problem with previous washers. I take them out IMMEDIATELY as soon as the door unlocks and shake them out and hang everything to dry. This worked great previously and I never had to iron anything or put anything in the dryer to get wrinkles out. Now, this washer wrinkles my clothing to an unbelievable extent so that they need to be ironed or a round in the dryer to relax them. This is true on Wrinkle Guard and using the delicate setting, set between medium and none on the spin cycle. Wrinkle Guard? I don’t think so. This thing wrinkles my No Iron shirts so they will have to be ironed or steamed.The washer leaves lint like residue most all of the time on dark clothing from day one. I most recently did a load of black only clothes that I did on delicate, soil level between med to extra heavy, spin speed between med and none, and, because of the dirty clothes issue, I had the extra rinse on. The clothes came out dirtier looking than they went in and looked like I washed them with a box of tissues and too much soap. They looked dirtier than before I washed them and had a whitish and lint like residue on everything. So I ran them through the same cycle/extra rinse again but WITHOUT any soap. Unfortunately I didn’t watch to see how much water the machine sensed that these loads needed and I didn’t see how much water was there - but I did for other loads after - see the next problem below. After the second identical cycle, the clothes had the same residue which I photographed and have enclosed below. (And still a wrinkled mess.)We have found that the water sensor can’t sense the proper water level needed and is likely not functional. Sometimes it seems like it might almost be be appropriate and sometimes not at all. Specifically, after I ran the black load through, I decided to try a small red load before my usual large blue load just to see how much water there was. Same settings as above, 6 small items that barely covered the bottom of the drum and the washer sensed a medium load. Certainly by volume of clothing this was not a medium sized load and if it goes by weight, it was the smallest load possible! Medium water level… These clothes seemed to agitate ok because they were completely submerged in water and came out clean. Then I did the much larger blue load that filled the drummer then halfway. This had so many more items than the red load and weighed way more. I tried the same settings as above and this time the machine sensed a SMALL load and the water level was barely halfway up the clothes, if even that much. So half of the clothes were out of the water and we watched and witnessed that the clothes did not agitate properly. This load came out like the black load so I ran the whole cycle again including the double rinse. This time, the same load was sensed to be a MEDIUM load although NOTHING changed except that the clothes were damp and lower in the tub as they were compressed from having gone through the entire wash cycle. They came out mostly clean, after the second wash, again, likely because this time they were almost covered by the water (2/3rds or so) and could move around a little better but still not great agitation.There almost never seems to be quite enough water so that the clothes are not able to move by the agitator and sometimes we watch and can see that the clothes above the waters never get pulled into the water. I understand that this machine may not completely cover the clothes but this seems way short on water and the fact that things usually come out dirty means something is wrong. There is often so little water that the agitator can’t possibly work the clothes into the water. So, next I ran an Oxi cycle and witnessed that about half of the items were not in any water and were only wet because of the filling cycle not because they were moved around by the agitator. How can the oxi do its job if the clothes aren’t in the solution of at least wet from the solution which I didn’t see as likely as the clothes didn’t seem to move through much if at all?Along with the same water sensing problem, why on earth isn’t there a manual water adjustment? If the water sensor doesn’t work, the other option is only the high fill setting. After finding my clothes still dirty when we first got it, I tried the high fill setting to see if this would help but the clothes still came out with that residue. This was the very first few loads I ran and was assuming it was just user error so I studied the manual and tried everything as recommended. Since reading that residue can result from too much water, I use the recommended sensing feature now. So, we can either have too much water or barely any at all…

I love the functionality of this Maytag refrigerator. The inside is so nice and big, I can almost fit anything into it. When I need to make a lot of food for a lot of people, this refrigerator really foots the bill.

My Maytag 2000 has ripped our clothes. This is my 1st front loading set. I looked on the internet and it seems that this is a known problem. Very upset that a brand that I had for 30 years and recommended to others as well has turned into a terrible company. Im a single mom and Im not in a position to replace a washer every year. I trusted Maytag! A recall and either replacement of the parts, or delivery of new part to fix the problem should have been put in place. I wrote to Maytag to see if they will do something to fix this problem.I have the set, washer shakes a lot, but works well. Washer also always has a lot of water left on the door seals folds, terrible design... I will post on other sites to warn other customers. This is not OK, my clothes are destroyed. See pictures. Clothes got trapped in a gap that exists in the perimeter of the opening, where it meets the door. Why is there a gap at all???

Like many others Ive read about online, our Maytag fridge model MFI2269VEW5 with bottom mount freezer has ice forming at the bottom of the freezer compartment. The ice then melts and runs onto the kitchen floor. At this point, I am able to prevent this leakage problem by removing the 1/2-inch layer of ice that builds up about once a week. Using a stiff plastic spatula, I am sometimes able to remove the ice in one large sheet but usually it breaks up and has to be removed in pieces. I have seen several videos online showing how this problem can be fixed but as a pensioner with limited income, I am sure the expense of a repairman would be prohibitive. I could likely make the suggested repairs myself but because of a knee replacement, I am not able to kneel for any length of time so that is out of the question. Besides, when we purchased this fridge 3 years ago, we expected it to run trouble free for the rest of our days. This is obviously a design problem and Maytag should be covering the cost for all repairs. However, it is a sad reality that Maytag and their owner, the Whirlpool Corporation is only interested in making a profit to satisfy their stock holders. They apparently only pay lip service to making quality products that last and customer satisfaction seems to be a thing of the past.

Dishwasher has been very dependable. Very reasonably priced and in over six years of service never had an issue with it. It’s a little on the small side for a large family but if you’re for less in your household-- works perfect.

I purchased a Maytag Bravos XL Commercial Washer on Jan.31, 2020. I have had problems with the control board twice in less than two years. To replace the control board it cost $560 plus dollars. I may as well get another washer. So, I have to buy two washers in less than two years, but the next one will not be a Maytag. I will not recommend their products.

Double door Maytag 3 years old has been leaking water in freezer floor and forming sheet of ice. After reading the reviews, I may decide to buy a different brand. Why spend more money on repairs! Very bad experience!

Maytag Free Standing 30-inch Gas Range - In 2004 we bought our model MGR5775QDS gas range with 5-burners because it offered the most BTU variety for the price: 1 burner with a high BTU (16K), 1 with low (5K), plus 2 in mid-range (9.5K) and 1 with 12K. Within half a year of using the oven, we turned on the self-cleaning function. Big mistake. One cleaning cycle later, our oven refused to ignite. The cleaning cycle burned out the ignition unit. Cant remember if its replacement then was under warranty but the repairman said this was a COMMON PROBLEM with Maytag and we best not use it EVER. In 2014 our cleaning lady mistakenly thinking she was doing us a favor, set the self-cleaning function. Once again, the ignition unit was destroyed. This time its replacement was $350 with part and labor. One and half months later, the oven is again non-functioning. This time our repair guy said the part is a very minor, inexpensive one BUT MAYTAG IS NO LONGER MAKING IT!!! The only way well get our oven back is if he can find another model and cannibalize it to fix ours. Are we disgruntled? Yes. Would we like to see a class action suit against Maytag for knowingly manufacturing a gas range with a malfunctioning self-cleaning unit that destroys oven parts? Yes. Will we ever again buy Maytag? Not on your life. A once stellar manufacturer gone down the tubes with a growing reputation for making junk. American-made appliances mean zip these days. Thank you for nothing, Maytag.

We bought our washer/dryer from Home Depot and felt Maytag was a good bet. Guess again. Washer is running fine for now but after light use (about 3 loads per week) dryer failed. With no warning, I heard a loud pop about 3 min into a cycle and overheating. If I hadnt been home might have caught on fire. Good for us we live close to a coin laundry so in no rush to replace but can bet when I do it wont be Maytag and thats too bad. One of the few makers still building in the USA but thinking Samsung is looking good. This is the Maytag 2000 series btw.

Maytag is a reputable brand name for a washer & dryer. However, they have done very well in the oven/range industry as well! I own a oven/range for over 4 years now and it works great???! Food is cooked to perfection and cleaning???? And self-cleaning is a snap!

Horrible washing machine. Cannot get clothes clean. It simply does not supply enough water to wash. Have tried everything. I want my money back. How do you start a class action lawsuit. Thousands of people are dissatisfied also.

I purchased the Maytag MDB7749SBM dishwasher just over 2 years ago. After owning for 1.5 years, the control board malfunctioned. After discussions with Maytag customer service that began in late December 2014, it was finally repaired in February 2015, with the control board being completely replaced. Within just a few months the dishwasher again fails. The first time, it would not stop running. This time, it will not run at all. I called customer service today (August 1, 2015) and they expect me to pay for the repair.It is easy to Google and find multiple review sites that indicate hundreds of consumers have similar problems, but Maytag will not acknowledge any issue, as the customer service rep indicated today (she said her information showed no recalls). Within two years I am now faced with paying $600+ for a dishwasher for a second time. This is terrible customer service on Maytags part. They have lost my business and I am warning consumers on every platform I have.

Purchased washer in Jan 2013. Average usage is 1 load per week. Last week the washer started leaking from the rear left side. A service call discovered that the bleach dispenser was filling up with water and overflowing. Bleach dispenser?? I never use it! Seems that the new bleach dispenser hose line has a relief valve whereas the original part did not. Internet research has confirmed that this problem is very common with this make and model. However, a call to Maytag requesting what compensation, if any, would be available resulted in a response that basically was too bad... so sad... cant do anything for you! Seriously? An apparent common, known problem and all they can say is we understand your problem. Needless to say that will definitely be the last lonely repairman Maytag that this household will purchase.

I purchased my Bravos washer and dryer in about July of 2012. So far I have no complaints about the dryer but I hate the washing machine as do two friends of mine. My husband specifically wanted something energy efficient which is why we didnt purchase the basic traditional style washer weve always used. From the first time I used the washer, I was amazed and disappointed at the noise level. Because the lid is glass, I could observe the water level during each part of the laundry cycle. The water did not cover the laundry in the washer.When I mentioned this to one of my friends, she said that she has to wash some of her clothes twice. How is this energy efficient? I finally figured out that using the heavy duty wash cycle and heavy soil setting usually results in more water but requires an hour to wash and rinse the clothes. The downside is that the heavy duty cycle is too hard on some of my more delicate items so I have to hand wash many more clothes than I did with my old style washer that allowed me to select the water level I wanted. Most recently, when I washed a bulky mattress pad with a few other items, the water level never covered the pad because the load of laundry was so lightweight. At the end of the cycle, parts of the mattress pad were bone dry so I will have to take it to the laundromat if I cannot make the washing machine fill up with water high enough to cover the mattress pad. I dont want to spend the amount of time hand washing so much of my clothing, monitoring the water level in the washing machine and rewashing loads of laundry. After reading many of these comments, it appears that I have many more issues to look forward to. When this washer starts to break down, I will go back to an old style machine and a different brand.

Maytag Bravos MCT washer not good - Owned this since June 2017. This thing has never worked properly. Every time after a cycle is complete we have to wring the soaked clothes by hand. Even after doing this the drying time ends up being double what it should be because the clothes are so wet. Not only time wasted on hand wringing clothes but also wasted energy in drying them afterwards. Also this thing is supposed to auto-detect how much water it should use but half of the time it uses too little water and doesn’t actually wash all of the clothes. Some clothes stay totally dry when this happens.

1st service call about 2 years after we got it. Put around $200 in it. Now broke down again. Service tech quoted $475.00 to fix it. So it was basically totaled after around 6 years. Nightmare kept getting LD (long drain) code. After hours of research I finally called service. Would not drain so I had to wring out a whole load of laundry and bail out the water by hand. Miserable experience!

Our Maytag microwave, which we bought based on Maytags supposed quality, is nothing but a piece of junk. In two years it has had or needs repairs that nearly double the original cost! Thats ridiculous. We are done with Maytag and are not going to get suckered into their Whirlpool/KitchenAid or other brands. So long.

I bought the larger capacity machines to save time because Im so busy with my family and wanted to cut down on loads. I was surprised to find the capacity can really only operate at half, which is as large as my old, smaller machines. The washer is extremely sensitive, meaning it may take four or five tries (this morning was four) to arrange the clothes - even a small load of delicates - in it in the exact way the machine wants before it will allow the cycle to start. This is exceptionally frustrating, particularly during the busy morning or when you are tired at night. So you have to stand there and wait until the sensing function is happy and you see the water pouring in. Yet often you will return to the machine and it will have an error message that occurs inexplicably during the spin cycle, so the wash cycle will need to be restarted. It cannot just be continued. The machine is not only a huge time waster but a water/detergent waster as well.I learned that the sensing function on the dryer is useless as well after coming back to many loads of damp clothes that sat there, got little funny smelling as a result, and had to be rewashed in the nightmare washer lol. So now I just use the timer function. It takes about two hours to dry a regular load of towels, so be prepared for that. I bought Maytag because it is an American-made product, but I wont make the same mistake next time. If the quality is any reflection of the functionality, it probably wont last very long anyway. Heres to hoping.

I have had a number of Maytag washing machines in my life and have never disliked a machine as much as the last one I purchased! The bleach dispenser is awful and any bleach that happens to land on the outer rim has ruined many clothes. I took them to my dealer to show him the ruined clothes and was told bleach does not evaporate do must be wiped off each time. With no soap dispenser I find I have to put the soap in first and keep trying to fill the machine some before I add the clothes. This takes forever but if dont do this my clothes are stained. I purchased this machine on April 11, 2017 and can not afford to go buy another washer at this time. The Dealer can not help me and when I called Maytag they were not interested! Buyer beware!

I am online now because we have the same problem. Our refrigerator is less than 2 years old. Watched a video on YouTube how to fix problem and repairman said engineers who created design must have been on drugs. I think hes right. Very common problem. Have to call repairman!!

Very easy to use- just dial the button to the load of your choice! The only problem I have is it becomes unbalanced sometimes on a heavy load. :( And it is also energy efficient and lets you know when it needs cleaning.

I had a Maytag dishwasher for 17 years, and it has still worked fine when we moved to another state. At the end of 2010, I bought a new Maytag (1) because my old one performed so well and (2) we left it at our old house. Well, slightly over two years later, this piece of junk (Model MDB6709AWAQ1) needs almost $300 worth of repairs. The repairman said they are no longer made to last and have been that way since about the year 2000. All of the inner workings are run by electronics which only last about two years. I said, What happened; the Maytag repairman got tired of sitting around doing nothing? I would never ever purchase another Maytag dishwasher, or any other appliance made by them or Whirlpool which took over Maytag.

Absolutely the worst washer I’ve ever had! Do not buy this washer. Even after a double rinse there is white matter left all over everything! I’ve taken photographs of my laundry after two rinses and it’s disgusting. I will be quite happy to submit the photographs at any time.

I bought the product thinking Maytag - should last a long time. Sadly I was wrong. Bought the microwave from Home Depot in May, 2016 and had it installed by them. The product worked fine for the first 14 months. In fact I thought it was great. It was quiet, heated things quickly - a great product. In July, 2017 I started having problems. The product would start. I was getting a message to Close the door to start the microwave, even though it was closed. When this would happen I noticed that when the door was open, the light wouldnt come on. It would require multiple open/close until finally the light would come on (when door was open). Only then, when I closed the door would the microwave operated as it should. I lived with this inconvenience until Dec, 2017. Of course - over the holidays is when it decided to quit working entirely.I did my digging and found problems with the switches. I replaced 1 switch - still didnt work. The cost to have a repairman come out is ridiculous (Sears wants $250). My frustration was growing and my confidence in the product was waning. So time to get another microwave. I was done. Frustration and anger doesnt begin to describe my feelings. I went with another brand. It isnt installed yet, it should happen this week. In the future I will tell friends to avoid Maytag microwaves. Apparently they just dont last. I realize this isnt a top of the line microwave, I only spent $299 (plus tax, installation...) but really - shouldnt it last more than 14 months before it starts giving me problems? Very disappointed!!!

Add me to the long list of disgruntled buyers of a Maytag Dishwasher. Just like the other 488 people that similarly filed an unsatisfactory rating on this site I too am now on that list. And no surprise - the control panel ceased to function 13 months after I purchased the unit and one month after the manufacturers warranty expired. After brief inspection the problem was obviously a design error leading to premature wear of the electric ribbon in the handle. Phoned Maytag and they advised me it was the first theyd heard of this problem with the model. Only subsequently did I search to discover that the problem was so common it might be characterised as routine. Replace part was 8 weeks and Cdn $153, about 2x the US price. However they wouldnt ship it to me from the US. The repair isnt too difficult: 11 screws and a little patience if youre so inclined. Before installing take a few minutes to trim the plastic where the electronic ribbon strip passes from through the handle without clearance. Save yourself the same repair in another 13 months. Lesson learned - no more Maytag/Whirlpool dishwashers for us.

Bought the Maytag top load high efficiency washer (also matching dryer which works perfectly) brand new less than 6 months ago. It is the worst. It leaves swirl marks on my clothes that doesnt come out. Leaves part of clothing dry without being a large load! If I put sheets in there it blows up like a mushroom and leaves that part dry. I use the correct detergent. I had a serviceman, that the manufacturer suggested, check it and determined there is nothing wrong with it which only leads me to the conclusion that it is a poorly designed product. Spoke to a manager at Maytag that said the machine works fine. And because it is in a business setting there is nothing they can do. (What? If it worked fine, I wouldnt be here.) Called to company I bought it from... Theres nothing wrong with the machine plus we are closing the business so its the manufacturer warranty that you need to call them. I would have been happy with a exchange. Poor design, poor customer service.

We purchased a Model MDB8949SAWO Maytag dishwasher in September 2012. The control panel failed in November 2015. We wrote a letter to Maytag (Whirlpool) expressing our disappointment and received a call from Maytag customer service. The Customer Service representative informed us because we contacted our local repair facility directly, no reimbursements would be provided. During a subsequent follow-up call, I was informed by the Customer Service representative that Maytag manufactures quality products and that no premature failures were occurring with Maytag dishwashers. The Customer Service Representative stated that we should have purchased an extended warranty which lends some support to the fact that Maytag dishwashers are essentially junk. Never again will we purchase any Whirlpool products.

It’s really quiet and it cleans the dishes, pots, glasses on just 1 cycle and I’ve had it loaded more than one time. I do use rinse aid and I do occasionally use dishwasher cleaner. I wouldn’t own angry other than a Maytag dishwasher. They last forever. The commercial about calling a Maytag service man is true! I’ve never had to call fior service! Well worth the money!

I bought a front loading Maytag Cloths washer model# MHW3505FW1, SER# C71451407 new in April 2017, from Home Depot, since then it has broken down three times, with a water pump, a master board, and now another master board, we were told by the appliance repair service that is used by Home Depot extended warranty service, that it will take a month to receive the master board. Thats it... Never again will we buy another Maytag or Whirlpool product. This is unacceptable. Gone are the years when Whirlpool and Maytag made quality products!

I love the fact that there is no agitator in this machine. It give lots of room when washing bulky comforters. I also love the vast amount of settings for load size and the soil settings. The con of this washer is that it has broken down on us twice in the 2 years since we purchased it. The pump has gone out both times. Unfortunately it looks like we will be making a purchase of a new washer in the near future because another mechanical issue has arose.

I bought a Maytag washer from Lowes and bought the extended warranty. The warranty expired but Maytag is not taking responsibility for the lemons that they sell. I have seen many reviews stating that the bearings went on the washer. This is what happened to me and it happened twice already. I spent 798.00 on this washer thinking it would last for more than 6 yrs. They offered me a warranty for 368.00 or to purchase another washer at a discount price. Of course I refused but I want everyone to be aware of Maytag Washers - not worth the money.

I just finished paying off my Maytag Bravos series washer and dryer, and now they are failing! The washer isnt getting dirt out and the dryer power button broke. And its not like I can use some pliers to get the switch to work, its like the part that controls the power just dropped out of existence, leaving me with a knob in my hand that connects to nothing! Of course, the limited warranty only covers the drums, not the little dinky parts that break more easily. I had inherited a set of Maytags and they were well over 20 years old (possibly 30) and they both were powerhouses. But this is terrible! I feel super disappointed that Im going to have to buy a new set after only owning these for 18 months. I know I WONT be buying Maytag ever again, though!

I think that I finally figured out a way around the piece of junk Maytag sold me. I bought a Maytag french door, stainless, yada, yada refrigerator in 2006. When it broke down, see later description, the first several times it was ok because of the warranty. This POS has failed 7 times requiring $300+ to fix every time. When contacted about the issue, the people at Maytag seem happy. The business model is working perfectly. There goes another sucker. The refrigerator begins its eventual breakdown with the door alarm light and sound beeping constantly. Beeping that continues for days and weeks. The next progression to failure continues with it not beeping anymore but now the interior lights do not light when the refrigerator is opened. Finally, the refrigerator stops cooling entirely and it is dead.Now, Maytag no longer wants anything to do with it so you need to call a repair man. When the repair man arrives, the entire time he talks about what a piece of junk Maytag is. They, every time, at first think it is the switches and replace them. This NEVER fixes the issue. Next, they have to replace the computer brain. $400 to fix. EVERY TIME. Now, at least every year. If you buy Maytag and have a similar experience, get your wallet out. Sell you junk then dont stand behind it.

Our problem started when the control lock button locked itself on. Called Maytag and told it wasnt covered by warranty but they did walk us through resetting the power and it fixed the problem until we ran the next load. Now when you try and set it, the rinse only light comes on. Bought the Maytag because I always believed them to be dependable - wrong!! I had a basic model Whirlpool running for a family of 5 for 25 years prior to this Maytag without ever having to call a repair person. Maytag wont deal with the issue so I would recommend to anyone else having any issues with unreliable appliances to do what I am doing - boycotting Maytag!!

I agree with other reviewers on this site. This top loading HE model does not get your clothes clean. Ive tried hot water, warm water, cold water. Large loads, small loads. Shirts come back with clods of dirt still on them. Pre-treating stain remover doesnt wash out of clothes. Terrible machine. I wish I hadnt bought it!

Unbeknownst to us, our Maytag Refrigerators (MFD2561KES) ice maker developed a problem with the fill hose which connects to the back of the refrigerator, causing it to pop off. The hose had been leaking water onto our wood floor causing all of the boards under the refrigerator and 6 feet in front to buckle. I cannot see why Maytag did not use a compression fitting instead of using a squeeze type hose clamp. Plus the ice maker has left a large sheet inside the freezer on the bottom. I use the ice maker daily to fill my cooler for work.We also have a Maytag Dishwasher which has a push button panel in front which has decided to give out as well. Not to mention our Maytag Double Oven which has never been able to close properly since we have had it. (The service man said that there is nothing wrong with it). We bought our house 7 years ago and my wife wanted nothing but Maytag because of our experience in the past. I gave up buying american automobiles years ago and I guess the same will happen when I replace these appliances (after I finish paying for my new floor).

I bought a fridge from Home Depot. It was on sale and not a Maytag. Somehow they delivered a Maytag. I am over-the-top happy with my fridge. It keep things cold. It is roomy, It has separate temp controls for the freezer and fridge. The bright LED lighting is wonderful. It is energy efficient. It is easy to move around when I need to clean under it. It was delivered right away.

We bought the Maytag Bravos Washer and Dryer set in 2013 after extensive reviews as well as the brand recognition to replace my at least 20 year old Kenmore washer/dryer. At first we were very pleased. The ability to do bulky loads was great and the high spin cycle left the clothes almost dry. In 2018 (keep in mind, just 5 years!) we started to hear a grinding sound in the washer when on rinse cycle and the dryer would randomly turn itself on! Strange but true. I called Maytag Canada and they sent someone right away. They had to replace the motherboard on both the washer and dryer as well as the drum and gears on the washer. Fortunately this was covered under warranty.Fast forward 1.5 years. Same issues with washer...technician came and could not identify the problem, although I did tell him it was the same as 1.5 years ago. I ended up recording the sound and asked them to resend technician to the house. After further diagnostics, yup...same problem. Two days went by and I received a call back advising me that the cost to repair would be over 700.00, not covered by warranty! I escalated to management, to no avail although they did offer me 15% off my next Maytag purchase! Needless to say I have ordered a brand new GE from Costco, arriving tomorrow for basically the same price to repair the Maytag. I will NEVER purchase another Maytag product and will advise anyone who cares to listen to me to do the same. Huge disappointment in the Maytag product, brand name and customer service. 10 year warranty? Not likely...stay away.

Front load washer unit does not respond to control inputs. I have called Maytag service and support. One can find a repair or maintenance manual. Im in a smaller market so there is limited service. Maytag service and online support is terrible. Maytag stores are fronts for independent service companies. Its probably okay, but misleading. Everyone wants to order the main controller board. It would be good to have a maintenance manual.

The machine dries out the clothes so tight that they are full of wrinkles. I am so dissatisfied with this machine, I spent almost $600.00 for this and this is what I get. I also end up with fabric softener all over the clothes. I use the Downy Ball and I just took out my black pants to find blue all over them. I contacted Home Depot where I purchased the machine. They said to get a hold of you. All I want is get a different machine, not an HE. This is beyond anything. Someone should have to put up with, can you help me?

I could not get parts for Maytag Model MHWE200XW00 Type 832A as the Whirlpool does not provide after sales service. I purchased the new washer in 2010 and lasted for just 4 years. I believe they guarantee supply of spare parts (Inner Basket, Outer Tub and Rubber Boot) for 10 years and more.

Just had the repairman here. This machine is computerized so it won’t last. It does not have a setting that lets me do any load of laundry the way I need to do it. I have to use heavy duty to do a load and then it takes 2 hours. When I want to do a load of sweaters on delicate it will not put near enough water in the machine to wash them. The normal cycle does not add enough water to wash, let alone rinse the clothes. I can’t choose the size of the load based on how much I need to wash so I have to do more loads at 2 hours each or do everything on bulky. Whoever came up with all this needs to be fired. I am extremely unhappy with this machine and I have loved Maytag for years. No more.

This product has cost us thousands of dollars in clothing!!!!!! We have a lot of pictures to prove this!!!! Greg Mackie Major Appliance does NOT back this product or US the consumer!!! We have bought THREE households of products from this distributor & they have NOT backed any of the products that they have sold us, or given us Any discount for repeat business or loyalty and have NOT Supported us in any way whatsoever!!!! We have spent thousands of dollars and have had NO compassion or support whatsoever!!!!!! We expect a full refund for this Failure of YOUR product & a NEW Machine that will CLEAN our clothing & NOT DESTROY it!!!!!! Very Disappointed in this Product!!!!!! We Will NOT purchase another product from Your Company or from this Distributor unless YOU make a conscience decision to make this situation Right!!!!! We Will Spread the Word about your Failure of a product & detour business from YOU & YOUR Distributor!!!!!! We have numerous other photos to share with consumers of how YOUR product has destroyed our clothing!!!!!

Centennial HE top loading washer - When I put the HE Tide powder in the washer, it does not always rinse well. I have to rewash often. I use very little soap.

Before you purchase a Maytag washing machine...from anywhere (I got mine at Home Depot), think again. This machine doesnt wash clothes, it doesnt rinse clothing. What it does is takes forever to fill up the tub then it doesnt even come close to filling it to where all the clothing is covered for rinsing or washing, then it just stops and sits there for a few minutes (??) and then it proceeds to empty the tub and youre supposed to feel like your clothes were cleaned.Not in a million years will your clothing get cleaned in a Maytag washing machine. Youve been warned...dont waste your money. Go to a used appliance shop, but the best one they have that does NOT have the Govt. regs built into it, and be happy you saved as much money and did NOT have to go through all the frustration and hassle everyone else has that bought a new Maytag washing machine.

Washer was purchased at Lowes under direction from staff... Great washer, environmentally better, less water consumption... Well washer is piece of crap. Activator is out, door stays locked, have to unplug to release every time used, water does not drain and cycles do not function or start. Lowes no longer carries product and all other review on spot as to cost to repair... Piece of crap, loss of $600.00+. Could be used as target practice, best case scenario.

This Maytag (1979 model) is about as good as other dishwashers (I always rinse before placing in machine). It does have a lot more buttons that are not used than the last one I used (installed in the 1950s). Delayed start, choice of preheating water or not, choice of drying. Not big enough to do everything when have company and too big to use when no visitors present. When I am alone it takes 3 months to get enough to fill the machine and by that time they are getting moldy so most of the time I wash by hand. Black glass front with imposing row of controls across the top. I normally do not generate enough dirty dishes to warrant having a dishwasher. Since my wife died I have used the dishwasher two to three times a year.

I purchased a French Door, Bottom Freezer refrigerator in the summer of 2006. Less than 3 years later, the ice maker door kept opening and closing and the lights on the door panel kept flashing. I called Maytag and found out there was a problem with the circuit board, and that it was under recall. The refrigerator was fixed at no charge and I was happy. Approximately 2-1/2 months ago, less than 7 years after I bought the fridge, it started getting too cold inside and then too warm and then too cold, etc. Then it stopped cooling altogether. From what I read, it was either a problem with the compressor or the relay on the compressor. There was a recall on the relay on some models, but not on mine. I cant even afford a service call. Let alone a repair charge. If the compressor is the problem, Im looking at a repair bill in the hundreds of dollars. The online price for a compressor is over $300. I dont have the money. So the beautiful refrigerator that I paid $2,000 for sits in the kitchen, unplugged. I never figured that Id pay that kind of money for a refrigerator and have 2 major problems with it in less than 7 years. I just got off the phone with Maytag and, of course, they cant do anything to help me. I was hoping to never buy another refrigerator, but if I have to or if I have to buy any other appliance, I will never ever buy another Maytag or Whirlpool. I will post everywhere I can about my experiences with this refrigerator.

Washer has plenty of functions for me to was even my work clothes. These saves me money and time. Washer leaves clothes clean and you can even wash your blankets.

Im extremely disappointed in this machine. I bought this machine after having my Kitchen Aid for 12 yrs. Just last month, the UL message came on. Had someone looked at it and noticed the bearing was loose. He fixed it, just today, it started doing the same thing again!!!!! Now it might be a suspension problem. Of course my warranty expired because I bought it in November 2012. Im never ever going to buy a Maytag washer again!!! Can someone help me to take my complaint to higher up?Thank you..

My refrigerator stopped working less than two weeks after purchase. The ice maker failed to produce ice. I feel they sold me a lemon. Yes, I do!

We received our new Maytag washer MHW8200FC on Saturday 11/18/17. We washed 2 loads on Saturday and on Sunday it didnt start. Not only did it not start but it was locked with clothes in it. We finally got it to open but it wouldnt start to wash. We had the distributor, Warners Stellian, schedule a service tech. He came out on 11/21/17 and determined the board was bad and that he would order one and be back on 11/29/17. A week without a washer doesnt work for a family of 5. This isnt like a lawn mower I use once a week, we use it daily. Whatever happened to quality control? A brand new expensive product breaks in 2 days? Maytag says its Made in the USA, which Im all for... Only if it works. USA or China, broken is broken so I dont care where its made. Whether its planned obsolescence or just a plain faulty product, Maytag is now another brand that I will avoid buying in the future.

I am absolutely disgusted with this Maytag Bravos XL washer. Have owned it 6 months and cant wait to get rid of it. We live on a farm and have cattle. If jeans go in the machine with mud on them, they will come out with mud on them. I have tried soak, deep water wash, power wash. Nothing works. I might as well put a wash tub in my back yard and wash by hand. Anything black must be washed by itself as it will come out covered in lint. How did this machine ever go on the market? Expensive mistake. Please do not buy this machine.

We bought this Maytag Bravos top loading washer 2 years ago after having bad luck with a front loading Maytag. Maytag was always the top brand to buy so I thought it was the style washer but now I believe Maytag has failed to keep their standard of quality high. My clothes come out of the washer almost dry and full of lint. Even though I use the HE wash soap, it does rinse out of the clothes. Dark clothes come out with a noticeable scum so I suppose the lighter clothes do, as well, I just cant see it. I sometimes have to wet the clothes down to get them clean and I always have to double rinse them which defeats the whole economy issue. Im not happy with this washer and would not recommend anyone to buy a Maytag brand washer.

Ice builds bottom of freezer then leaks onto floor. Should be a recall.

I bought a brand new Maytag bottom freezer fridge in May 2005. The first thing to go was the timing switch. I lost all contents of the fridge and freezer. The next to go was the compressor. Again, all the contents of the fridge and freezer were destroyed. This was after the 5 year warranty was complete. The cosat of repairs is around $800.00, which is the cost of a new fridge. I emailed someone from customer service, who replied how happy they are to hear from me, and how I can call anytime. I called customer service, and spoke to a supervisor. The fridge was built in the USA, but cannot tell me where the parts are from. No one seems to get, that I am disgusted that an appliance would last only as long as the warranty lasts. Oh, and the repairs are only covered for 90 days. My parents have a 62 year old RCA chest freezer that is still going strong. The lesson is, dont get rid of your old appliances. They may use a lot of energy, but they last. I will never buy from Maytag, ever again.

This so called high efficiency washing machine, and others like it are absolutely awful. They do not properly clean clothes. I frequently have to put loads of clothes through two or even three times in order to get things cleaned properly which our old washer did easily in one wash. That is the exact opposite of efficient. It is so bad that it actually borders on being a genuine scam. Do not buy! Huge waste of money.

Maytag Bravos quiet series 300 - We have had this washing machine for approx. 2 years and there is rust marking around the opening of the spout where the bleach is poured into. We also find that we have to do the clean cycle quite often. And it bounces and make a loud noise if there is not enough clothing in it… even on the bulky cycle. I WOULD NOT RECOMMEND THIS PRODUCT TO ANYONE! And we have been loyal purchasers for 40 plus years!

We have a Maytag dishwasher that came with the house we purchased in 2012. Im not sure of the exact age but the former owner said it was a relatively new installation. The appliance works very well; cleans well. Just a couple of things of concern. First, it is really noisy. The fact that we can very clearly hear it running in the adjacent room does not speak well for it in this regard. The other things that has occurred is that rusting is evident on the trays of the dishwasher. One of the upright pieces has already broken off due to rust and two others are close to coming apart very soon. Nothing sharp is placed in those areas that are coming apart so there would be nothing remarkable to disturb the plastic coating on the wire racks. I can only conclude that the plastic coating was defective at the start; hence the rusting at the base of the upright pointing racks. That said, it does clean well but I dont foresee this unit lasting much longer overall due to the rack damage that is continuing to occur. I would expect the racks to at least last as long as the dishwasher but this does not seem very likely at the rate the racks are deteriorating.

Deceptive company and won’t stand behind their product! Purchased brand new washer. Identified and reported noise that I can hear upstairs in my house while washing to technician. Changed a part, not related to the noise. Called back out. He admitted he could hear the noise. Whirlpool engineering department says normal. Sorry, I should never hear a clicking noise upstairs with two closed doors and 150 feet between me and the washer. Will be going back to Samsung next time.

First we bought the washer and not even a month after it was ruined. In the span of the year that weve had it, it has broken down about three times. Then we bought the matching dryer in August and by the beginning of December it has broken down. Called customer service and they are not coming until January 18. Have me waiting over a month to fix it. Worst brand ever and even worse customer service. Never again will I buy anything from this brand.

I bought a new Maytag Quiet Series 300 in 2005 and have had nothing but problems with it. The internal plastic pieces that hold dishes in place have broken off regularly. The door handle also broke. The dishwasher does not drain all the way every time. Now, the dishwasher will quit randomly before finishing its cycle. Our model (MDB7600 AWB) was not part of the recall, but is a lemon nonetheless. Of course, all of this occurred after our one year warranty had expired. This dishwasher is a lemon and a waste of $400. Well never buy another Maytag product.

Maytag products are a waste of money! I purchased a Maytag Front Load Washer a couple of years ago during the Cash for Clunkers rebate where we were asked to give up our reliable machines for so called energy efficient new models. After spending over $1,000 on this fancy front load machine and having it installed, I go to use it the first time and it won’t work. It took me a month to get someone to come and repair the bad board on it. I then started to use it and after a year, the thing started making a horrible loud noise. I called the repair folks and they told me it is out of warranty. I called a local repair guy who told me that the drum is shot and that it will cost $700 to repair. So I got a total of 10 months of use out of this stupid thing. Thats $100 a month to do my laundry! I would be better of dry cleaning! I have searched the web and see that this is a common issue and that Maytag refuses to make this right. Well, I can choose to never buy a Maytag again. I hope that others will heed our advice and do the same.