We have owned a Maytag Commercial Centennial washer for 4 years and made the mistake of not buying an extended warranty as we thought Maytag was dependable and a reputable company and thought the manufacturers 10 year limited warranty would cover us. Washer would not spin clothes properly, started making loud noises, lid would not always unlock as time went on, and finally it broke and soaked my tile and it ran through my wall into my hall carpet. Called Maytag and was told we didnt have a 10 year limited parts warranty 6 times (we still have the book that says we do), they offered us a 1 year full warranty for $320.00. We purchased the warranty 11/04/16, Called Maytag as no one knew where the parts were and was told service plan is through AIG. AIG couldnt tell us where the parts were either and when I asked for our refund and we just buy a new washer they advised me they would have to prorate it.Now I feel held hostage. Parts finally come in and Maytag Certified repair man comes to repair machine on 11/30/16, only to be told they could not fix our washer as the screws and transmission rotted and fused to tub. Call Maytag as this should be under my warranty and everyone insists I dont have a warranty. Filed complaint 11/30/16, they sent me a survey on 12/2/16 and I filed my complaint again on the survey. No call from Maytag. Call back on 12/06/16 to be told the survey was them closing my complaint. Now they escalate my complaint and will be called in 48 hours and give me an email address to email my pictures of my warranty. Surprise no call back, so I called them again 12/08/16 and I am advised it takes 3-5 business days. Ask for supervisor and he told me even if I have warranty they will only cover the basket.I will have to pay for technician, and other parts. Still no info on my complaint and you cant talk to anyone just have to wait. I emailed Jeff Fettig CEO of Whirlpool (Whirlpool owns Maytag) as well on 12/6/16 a copy of my complaint with pictures of warranty. The bottom line is Maytag sells junk and their customer service is worse than their product. After being without a washing machine since 11/04/16 we will be buying something Whirlpool does not own which is very limited which is why they can get away with making junk.

Approximately one week ago, the display on my fridge began to flash and ice door flap continuously opens and closes. Upon researching the issue, it seems to be a very common issue and a known defect. One in which was apparently a recall at one point. I was told by a Maytag representative that the recall was from 2007 to 2009 and has since expired. Expired? Its a known defect and should be the responsibility of Maytag to provide the parts and labor to repair the fridge. I asked for a supervisor and was told that one would contact me within 24 hours. Well, about a week later, I never received that call so I called Maytag again. This time I was told by the maytag representative and a supervisor that there was no recall and that it was a Quality issue. A play with words, in my opinion. Anyhow, regardless of the title the issue was given, I was told I would be responsible for the repairs and costs. I attempted to look up the recall on Maytags website and had seen the last two letters of the serial number to my fridge listed under the recall, but when I tried to investigate further, the site referred me to the 800 phone number I had been calling. Now, had this been an issue that was not a known defect and apparently a recall, I wouldnt be writing on this site right now. But, because it is a known defect that maytag is aware of, I think its Maytags responsibility to pay for the parts and labor for my fridge.

I read the reviews before I bought this washer, went to a major department store to buy it. This way I knew that I could get good support if something happened to it. Its been 3 months, I use the washer everyday. There are 4 adults in my building, they use it daily. I have never had a problem yet, the clothes come out cleaner than the front loader I have. It seems Maytag still makes a good product. I am the first to admit, when you make large number of products you will have some with a defect. But this washer the Centennial by Maytag works great.. Plenty of water in the tub, the clothes come out clean.. Maybe those people having problems need to stop buy at big box home centers. Theyre known for lumber not washers.

This is an awful product. I bought this product from Best Buy at the beginning of August 2018, and can no longer return it because it’s past their 14 day return policy. This washer does not wash clothes well. No matter what setting it’s on, clothes come out looking dirtier than prior to washing. Maytag should do what is right and refund customers for this worthless purchase.

Maytag Dishwasher Model # MDB7749SBM1. What a piece of JUNK! Purchased in June 2013. Control panel went out six months later! June 2014 Control panel BAD again (#2). March 2015 another Control panel replaced (#3). Thank God for Home Depots extended warranty! October 2019.... Control panel needs replacing!

Bought a new Maytag dishwasher in July 2013. In December it quit working and the problem was the control panel. The service tech knew automatically what the problem was when he arrived. It is now May 2014 and the control panel has gone out again. Contacted Maytag and was told they will extend the warranty another six months from the original warranty. After reading that this has been offered to others with mixed results I have my doubts on whether it will be honored. This is our last Maytag appliance.

First I would like to thank the salesman who has worked diligently to solve the problem I am having. The first load of dark clothes I washed came out with what looked like lint on them. It has to be scraped off. Yes I am using HE detergent. Yes I am using the minimum amount recommended by the manufacturer. & yes to all the other questions I have asked. The solution was to wash the dark clothes on power wash with an extra rinse. Very energy efficient! This was NOT the answer so I was given a 1-800 # to call. After giving all the necessary information & answering all of the questions about detergent etc. the conversation became a little more in depth. Does it happen with dark clothes? Do you dry your clothes outside or in a drier? It was becoming obvious to me that Maytag is aware of this problem. By this point I was even unhappier as no solutions were being offered. Finally after several would you mind holding the line again for just a minute he said he couldnt tell me to do this but some of his friends add a cup of vinegar to their wash. At this point I told him I was sorry I had ever bought this machine. He then said he would have a technician arrange an appointment. He arrived & declared I was using too much detergent even though by then I was using half on the manufacturers recommended amount. Buying an energy efficient washer where I have to use POWER WASH, EXTRA RINSE, VINEGAR & DRIER is not a good answer for a problem Maytag must be aware of as I read the reviews today. I have just done 2 loads of dark laundry with no detergent & the pants are marked so I WANT AN ANSWER.

RE: 5.2 CU Ft Top Load Washer, Model # MVWB865GW0, Serial # C84370937 - Purchased Jan 2019. The clothes come out terribly tangled and severely wrinkled, even when using the Wrinkle Control or Delicate cycle and occurs in every load size. Ive tried every cycle, including the deep fill and low spin speed but items are so wrinkled that whether I lay flat or hang or put them in the dryer, I have to iron them, which I never did before.

3 years ago, we purchased all new Maytag appliances for our home. Within one year, we had issues with the top load refrigerator getting warm and the bottom load freezer getting extremely cold. After calling Maytag and getting horrible customer service (long wait on the phone, no supportive/suggestive advice, rude representative), we were given a phone number for a local Maytag repair man who charged $300 just to walk into the house.He was literally in and then out of our house within 10 minutes. His advice was to unplug and defrost the refrigerator for 24 hours. Thankfully, his suggestion worked, but should have been given to us as a troubleshooter by the representative on the phone with Maytag.We have had to unplug and defrost the refrigerator about every 3 weeks since. It has become very annoying and stressful. There is obviously a defect in the refrigerator that should be replaced by Maytag! I will never buy a Maytag product again.

I have a Maytag refrigerator, Model #MBR 2256KES6, that is only 18 months old. It has totally stopped working. First, there was a large puddle of water on the kitchen floor and then a loud clicking noise in the middle of the night. It does not cool the fridge or the freezer. I cannot believe that a $1300 product is done working at 18 months. I cannot afford a new refrigerator. They should be arrested for selling such junk to the public.

Maytag Dishwashers work great. It cleans well and appearance is very good. I have always trusted Maytag appliances. Its quiet running and also energy saver. If I had to replace I would stay with Maytag.

Same as everyone else, ice freezes up on the bottom and water runs out all over the floor, ruining my new floor. Whole kitchen was new including all appliances. Maytag is ruining my floors. Can find no drain pipes so not sure where the water is supposed to do. I think they forgot to install one. But I am getting pretty sick of seeing my floors ruined and stepping in water.

I wish I had never bought a Maytag refrigerator! Nothing but problems. The ice maker does not work, water leaked 3 times onto our wood floor. Finally, I disconnected the control panel so I have an ice/water dispenser that is useless just like the refrigerator. I dont think the Maytag man is sitting around from lack of work, maybe laziness. Dont buy a Maytag.

I bought a Maytag dishwasher (MDB7749SBW1) about 4 years ago. Ive had to replace the wiring on the control panel each year. This is clearly a design defect, and Maytag will not take any responsibility for it. Ive called each year, and am told each time that theyve never received a complaint about this issue. This year Im replacing the dishwasher. Ill never buy a Maytag product again.

I bought the Maytag Centennial Washer a year ago. I have had nothing but problems. The clothes never get fully wet so you have to wash clothes 2 or 3 times. The lid does not open when running. So you cant put soap after the clothes are damp. I say damp because they dont get wet. Right now the sensing light has been on for 2 hours. I need to catch a flight in the morning and I cannot wash my clothes! My white clothes never get clean. I have to wash 2 or 3 times. Actually 4 time would work better. The water and electric wasted with washing over and over again is nuts. Stay away. Ive warned you!

I purchased range in January of 2011. I have had the top replaced and still it looks bad. Every time I use a burner, even if boiling water, I need to use the razor scraper to clean the burner. I’m very dissatisfied. We used to say we would buy nothing but Maytag but not anymore. Tell anyone who will listen how much I hate this stove. Oven does not cook properly, burns most everything I bake no matter if I lower the temp and time!

We bought our set when they first came out at Home Depot. We gave a pretty penny for the set. The first complaint was soon after I got them home; the washer gets the clothes so tangled up its hard to get them out sometimes. The 2nd complaint is, for a couple months now, the UL light comes on and beeps. I have to open the lid, close it and it starts that part of the cycle over and it usually does 4 to 5 times before it actually spins and finishes. I put it in the shop; they said they cant find out whats wrong with it. They said the leveling rods are still new looking. I was like, I know its still a newer set. Its money for nothing. I called Maytag. They want to charge me over a $100 just to come out! Rip off! Do not buy this set. Beware! Im still having problems. I will not buy a new Whirlpool set because they bought Maytag out and I will not buy a new Maytag set ever again!

Purchased a pair washer/dryer Maytag Bravo XL module from Home Depot, Brentwood, CA #1076 branch. The first day I received my machines, the dryer had a defect. I called them within 24 hours to report the issue and requesting a return. Home Depot wont take it back; they said I have to go though the factory warranty to fix any problems. Its like buying a car, once you drive it off the lot its yours they said. 3 weeks after the washer started making noise. Home Depot kept delaying my claim for more than six month so I couldnt dispute the charges with the credit card company and avoid the California lemon law. I consider this a loss of money and time. Worst appliance purchase experience ever.

Bought new Maytag French Door with cooling drawer refrigerator in July, & have had nothing but problems with both product & customer service since. Have already had 2 service calls for the SAME problem. The in-door ice maker/dispenser is a horrendous mess. Place a container below the opening to get ice cubes & ice is sprayed in chunks all over the floor & around the kitchen. To get ice, you have to put the container in direct contact with the opening, & then place a towel over the entire in-door unit to keep ice chunks from spraying all over the floor. The unit has a small flap-door in the ice maker, which must open & close automatically when getting ice, but the flap failed to close, so the ice in the ice maker was melting & the water running into the refrigerator unit & onto the floor. Called warranty repair & they came out & said they fixed the door-flap, but they did not. Ice was still melting & the freezer unit would not even keep ice cream & pastry items frozen solid. Called repair a 2nd time during the first 4 months of ownership, & they came out & replaced the motor to the small door-flap in the in-door ice/water unit. When asked why the freezer would not keep ice cream & pastry items frozen solid, the repairman stated (quote): Freezers dont keep ice cream frozen solid because it has so much sugar in it, its like alcohol. Had no excuse about the pastry issue however. We replaced a 12-year-old Jenn-Air with this piece of junk, but at least the Jenn-Air kept ice & ice cream frozen solid, & the ice maker did not leak & spray ice around the kitchen. Jenn-Air must know something about freezing sugary ice cream, that Maytag/Whirlpool do not understand. Then today we got a notice that Whirlpool had denied payment for the 1st repair visit, even though the unit was only 2 months old then. As such, we expect them to deny payment for this 2nd visit, even though the unit is now only 4 months old. Bad product & sloppy customer service, from a company with ZERO consumer support.

Both the microwave and French door fridge handles are crap. The microwave has completely broken and the fridge is very loose and will soon break, Im sure. Both are less than 5 years old. I will never buy Maytag again.

Bought this Maytag Bravos Washer online from Lowe’s in the holiday season of December 2017 because my previous Maytag HE washer broke after 17 years. I have had nothing but issues with this washer right from the start. The clothes do not come clean as I find myself putting them through the wash cycle two or three times to have them washed and come somewhat clean. The clothes come out soaking wet that I have to put them through the rinse and spin cycle at least one or two more times. I called Lowe’s to complain about this washer and they said they only have a 30 day return policy and they would be happy to call for service for me. I told them it didn’t work from the start but they didn’t care. So now, sadly, I have a repairman coming this week to fix my new washer, And hopefully he can fix it that I can use it and it can properly wash clothes. I wish I would have her read the reviews on Consumer Affairs about this washer before purchasing this Maytag. Not happy with Maytag. I would have never bought it and bought a different brand. Codes appear on the face of the washer better. Nowhere in the manual that I had to personally download myself because it didn’t come with one. And oh did I mention that I need a step ladder to reach into the bottom of the tub? This washer should come yellow because it is definitely a lemon!

Would give them 0 Stars if that was an option. Bought a Maytag washer and dryer in Aug 2021. Washer broke Jan 6 2022. Called Maytag/Whirlpool on Jan 6 as it was still under warranty. They only had one service company in our area to work on the washer. I called them and it took them 10 days to come see what is wrong. Ordered parts. Said it would be 2 weeks. We are now 6 weeks into this with no parts. Called customer service and they said they were notified that their service company needed a part and would take another 21 days to resolve. Talked to a supervisor (Demetrius) who sounded like he did NOT want to be in that position. Offered no solution other than we will just have to wait. Threw a 3 month extension for the warranty on which still does not fix the problem. Sad to see this company go down the tubes as it was once a pretty decent business with solid products. No longer.

The low water usage design is horrible. Clothes dont get clean as it doesnt use enough water to cover them. Takes twice as long to do a load as our old washer. Took about 1 1/4 hours yesterday for 1 load using heavy which is the only setting that uses more than a thimble of water. Should have looked for a commercial type with a real agitator and adequate water usage. Not saying Maytag is probably any worse than any other brand of new efficiency government mandated garbage washer, but its no good.

We got Maytag 2000 series front load washer just over a year ago. The bearings in the drum are already worn out. I will never buy a Maytag again.

I bought a Maytag refrigerator, model MBF2258XEW, March 2013. Bottom freezer, single door. The past 3 or 4 weeks I have been noticing water occasionally puddling on the floor at the freezer. The ice maker has never been hooked up, with no problem before now. I recently noticed that my wood floor is darkening in a spot that often gets wet. After reading some of these complaints it appears I am not alone experiencing water problems with something that is sold on its reputation for being trouble-free. I also see that I should expect to pay a few hundred dollars out of my pocket to fix the problem. Very disappointing.

This Maytag Dryer (Model #MEDP575GWO) was delivered January 29th and the paint on top of the dryer is bubbling and peeling. I haven’t even had the unit 4 months yet and they tell me the warranty for “cosmetic” reasons is on 30 days. This is completely unacceptable and I will sue them if necessary. I am in utter disbelief.

We purchased a Maytag 4.2-cu ft High Efficiency Top Load Washer from Lowes. The pump went out within 6 weeks of purchase. Maytag could not get a technician to come to our area to fix the washer. They finally told me they would give me $150.00 for labor if I found someone to fix it. We ended up taking it to a Maytag certified repair shop. It cost us a $99.00 service fee. They ordered a new pump from Maytag, part cost 137.46. I called to get a reimbursement from Maytag and they denied my claim. Their reason I was told was because I didnt call the part in myself. I dont understand why they didnt even reimburse the $99.00. The washer was a lemon and Maytag did not honor their offer, nor the warranty. Very time consuming and bad experience.

CONSUMER BEWARE! The Maytag Bravos X is without equal the biggest disappointment I have ever had the frustration of using. What a rip off! Water goes in, water goes out and it makes A LOT of noise. That’s it! (That locking lid should have been our first clue.) Specifically, a normal load takes one hour. What you save in water you pay double for in electricity. If you place a folded pair of pants in the washer that’s the way they come out; folded. Two twin sheets and a small blanket come out of the washer with dry spots every single time. If I use liquid fabric softener the clothes come out spotted with it. And it is louder than the train. You would be 100x better off purchasing a washer at a yard sale for $25 than to throw your money away on the Maytag Bravos X. DON’T DO IT.

I purchased two high end Maytag machines, one washer and one dryer, approximately 36 months ago. I did not buy the extended warranty because I was foolishly convinced Maytag sold reliable products. The dryer required service twice within the first 18 months. The washer, which is computerized, is almost unusable. The sensors dont work properly. It does not spin without continual restarting the machine. It takes me hours to wash one load of laundry, and even then it is not spun properly. I wrote Maytag headquarters twice via e-mail, with no response. Even though their website says someone will get back to you within three business days. I called Maytag on August 12th and was told there is nothing they can do because I didnt purchase the extended warranty. So the bottom line is you can spend thousands of dollars on their machines but dont expect them to last, or work. And Maytag will not stand behind their products.

We owned the washer for 2 years and 2 days when we got a code F70. After searching online, I found hundreds, if not thousands, of reviews and self-help forums that show this product is in dire need of a recall. The problem I had is the motor control unit (MCU), which is a $225 to $275 part online. However, Maytag will only replace the board under extended warranty with a refurbished board that they say costs $330, whereas they say the new one is over $600. Why is it that Maytag charges double what everyone else charges? If so many people are having these problems, it is obviously a defect and should not be the consumer’s responsibility. It is obvious that this is too common of a problem.

I am grateful I dont have to beat my clothes on a rock. Absolutely the worst dryer Ive ever had!!! Previous Kenmore washer was my favorite! This Maytag does not allow me options to stop, soak & freely open & close as I choose. Even my adult children who occasionally use it say its the worst!

My husband and I purchased a Maytag Neptune washer and dryer set back in early 2005. It was our very first major appliance purchase together as a young couple. We were talked into going with the Neptunes as it was considered one of the high end models at the time, and it came with a 10-year manufacturers warranty, which by itself was a major selling point for us. We have now had our Neptunes for a full decade and I am happy to report that we have not had one single problem with either the washer or dryer the entire time we have owned them. In fact, they are still going strong to this day. However, as it has been 10 years, it is now time for us to upgrade. We have purchased all new kitchen appliances within the past year and we decided that its now time to upgrade our washer and dryer as well and go with a steam set. We will most likely end up selling our Neptunes since we will have no use for them once we get our new set. They have served us extremely well over the last 10 years and we wouldnt hesitate to buy Maytag appliances in the future.

The bearings and motor went out in less than 3 years. The warranty good - the dealer I purchased from Siano Appliance gave me credit to purchase another Maytag washer - which I had to purchase an additional warranty for $320. The new Maytag is less than 5 months old - the motor has been replaced and waiting on a tech now to fix it. It would not come on. SO in warranties I have paid over $640 and am still having issues with the new washer. The first time I purchased a warranty for 10 year - when the machine was replaced I had to purchase another warranty for that machine - now if I have to replaced this one that will be an additional $320. IS this legal?

I purchased a Maytag Bravos XL Commercial Washer on Jan.31, 2020. I have had problems with the control board twice in less than two years. To replace the control board it cost $560 plus dollars. I may as well get another washer. So, I have to buy two washers in less than two years, but the next one will not be a Maytag. I will not recommend their products.

Always have bought Maytag. 16 years on both washer and dryer. The newer models, which I dont have, locks the top of the washer after it starts. I would hate that. I dont care if they are stackable but I would want full size. I dont think I would pay extra for a front loader, but the only front loading washer I have ever owned is small and at our camp.

This Maytag bravo washing machine is the worst ever machine I have owned. I bought it new, and shortly after the 1 year warranty expired, I started having problems with it. I had a repairman come out. All he did was take out the trouble shooting guide, press a code, and wait. The machine told him that each function worked. Even though it did not work properly. He hid the trouble shooting guide inside the machine, so I cannot get to it. Now I have so many problems with this machine, that it takes me all day to do 1 load. This thing makes noises that I have never heard from a washing machine in my life. I would never buy another Maytag product, nor do I recommend anyone else to buy one.

We had a Fisher & Paykel Washer that lasted 14 years. This Maytag Bravos XL washer has been the worst machine I have ever owned. The clothes come out dirtier than ever. In todays world all technology is becoming disposable, Where is the Maytag repairman now? I have tried all of the settings, to have a decent wash. I am ready to throw this out. Lowes you need to do something about this. It may be made in America but now we know why Japanese and Korean electronics just work! Damaged Clothes/Clothes not being washed thoroughly enough are my biggest pet peeves with this washing machine.

Maytag Bravo XL -Model MVWB88OBWO. Washer quit after 13 months of light use. Repairman came, $148.00, worked on just a few setting for 4 loads. It has a bad controller and some other part. Total cost of repair, if I was stupid enough to make it, $650.00. Guess whats going to the trash. I guess that kind of negates the ECO-FRIENDLY, huh? I will NEVER own another Maytag appliance.

Maytag Model #MBR2258XES refrigerator purchased May 2014 from Home Depot. Problem #1: Freezing in refrigerator compartment (frozen vegetables). Problem #2: Water leakage on floor from defrost. Wood floor is/has expanded and may now be ruined. This model is now discontinued. Looking into contacting an attorney.

My Bravo washer will not wash a set of sheets without dancing across the floor. So irritating to have to run in and separate the sheets that have ended up in a ball. The dryer is ok. Except my old Maytag had a loud buzzer that went off when the cycle was done. My new dryer has a dainty little chime that cant be heard if the washer is going. Wish I had my old set back!

I bought a Maytag washer about 4 months ago and the dryer the washing machine has went down a couple of times but I managed to get it to start again. This time it will not start back up. It just as a little water and stuff and will not lock and wash. It never gets the clothes clean and you have to wash them twice or at least a residue on the clothing. I hate this washer and Im very saddened that Maytag will not come out - told me that they had to find someone. There was no one in the area that could fix my washer. It has been nearly a week now and no response from them. Im going to have to buy another washer. I am so upset to spend nearly 800 some dollars on a brand new washing machine and it does not work. I think that was all the complaints that I have seen on this page so somebody needs to put them on the news and also someone needs to start a lawsuit against this company. Shame on you Maytag. Very unhappy with your product and you.

We paid for a brand new washer and dryer from Maytag/Whirlpool. Right on the machines it has stamped in a metal plate 10 year warranty. So at 4 years when my washer started screeching and smoking I called for service. Yes, there had been a leak that burned out something in the engine and the bearings were shot etc etc. But they have been back 3 times. Each time they lack some part. I first called them on July 29, 2020. Today is October 13, 2020. They have still not got the washer repaired. I need to do wash every day. We are a family. We also have a senior in her 80s. And dogs. I need to do wash every day. So for weeks I went to the laundromat. That cost a fortune. Then a couple of weeks ago I impulse bought a new washing machine. A Samsung. On sale. Doesnt match the Maytag dryer. And the old washing machine got moved out to the garage. Its the pandemic. I cant keep going to the laundromat. What good is a warranty if Maytag/Whirlpool always has excuses for why they dont have parts. Its the motor. The very basis of the machine. It took them 2 weeks just to look for one. You wouldnt believe the excuses they make when we talk. But I am really unhappy with the way it all worked out. What good is a repaired machine 3 months later than I needed it. I had to buy a new machine. Why didnt they just tell me to do that on day 1 so I could avoid the laundromat. Why are they spending so much money to basically repair everything in that washer when they could have just bought me the new machine. When is a warranty not a warranty at all, but just a big lie?

I wrecked on a bike, had surgery and in a wheelchair. I bought and had a Maytag dishwasher delivered from Beaumont Home Depot and this mdb7749sbw2 model never never worked. Home Depot told me I had to bring it back myself (Im in a wheelchair at the months that was impossible) and I called Maytag warranty. They sent a tech. He replaced a front power panel that didnt work. They sent out two more techs and they said use other soap Lemi Shine and the other guy said use Finish and turn your hot water heater all the way up. That never worked either. I have had this a yr and it just sit there and money in the trash. It makes me sick.

My dishwasher was bought December 2013. The control panel just started going crazy and cant control anything. Unless you have bought extended warranty Maytag isnt doing anything. This is obviously a manufacture defect and no one is doing anything about it. Will no longer buy Maytag products if they cant stand behind their product.

I purchased an Atlantis washer in 2005 and assumed that Maytag was still one of the better manufacturers. How naive of me! What genius at Maytag thought it was a good idea to place the water filter inside the washer? Not only can you not keep the filter clean so that cold water will flow properly, even worse, if the filter completely clogs, the water will not stop filling into the tub which could, of course cause an overfill and flood. I narrowly escaped this scenario once. No one should have to stand and watch their machine fill with water to insure it stops. Now the machine is causing a grinding noise when agitating. I expect it to stop working any day. I will not buy another Maytag or Whirlpool, who of course now owns Maytag. And I will not pay another repair bill for the filter or any other part. The brand was once considered the best in America, now its just another brand thats a piece of junk produced in another country.

I purchased a Maytag built-in microwave and oven combo in 2005 for my newly built home, but I did not move into the house until 2008. So the appliance has only been used for 3 years. The microwave stopped heating after only 3 years of use, which was for microwave popcorn mostly. I also purchased, at the same time, a Maytag cooktop. The knobs had to be replaced, a dishwasher, a rack and utensil holder had to be replaced and a washer dryer that doesnt work properly. I also purchased a side-by-side refrigerator which is okay so far. Im very disappointed in their appliances and they were expensive.

I purchased my Maytag Bravos washer and dryer in July 2007. As with any appliance, we always purchase the extended warranty as it usually runs about $100 on appliance. My first experience with problems was in February 2010 when the control panel went out. If I had not purchased the extended warranty, I would have been in trouble. It ran out in July 2008. It was downhill from there. In September 2010, it quit spinning; and the fabric dispenser would not work. I called again in September 2010. The tub was out of balance. In June 2011, the panel control went out again. In November 2011, it would not spin. In June 2012, the panel for control had to be changed out again. In July 2012, now the pump is leaking. And guess what, my extended warranty is up 8/1/2012. I contacted Customer Service, which said unless there was the same problem within 12 months, there was nothing they could do. Well, Im fired up. I intend on making a complaint with the Better Business Bureau and anyone else who will listen to me. I paid over $2000 for the washer and dryer, and it should last more than 5 years. This is ridiculous! When Whirlpool bought out Maytag, then the product went to crap! Dont tell me the Maytag repairman does not have anything to do now, because I know I keep him real busy. I am so tired of the companys just blowing you off when you work hard for your money and purchase a product for your family that should last at least 10 years. I am a principled person, and this is not going to go away easy. The repairman is coming next week to fix it again. I am going to give him an earful as well. The last one who came to change out the panel board (3rd time) said they had nothing but problems with this unit. Well maybe they made it that way, so when the warranty runs out, they can charge you an arm and a leg for the part and the labor to repair. I will never buy a Maytag product ever again. My next one will be the new LG washer and dryer. Talk about the lemon law. This product from what I am reading here should very well fall within that category.

We purchased this Maytag Centennial washer in 2009 (model # mvwc6esw/Wd; type 849-05; ser # cy1741855) and I have hated it ever since. I had an old 406 Maytag washer that was worth its weight in gold - repaired it as long as possible. I bought this new one because it was a Maytag and that was a mistake. The way it agitates my clothes get tangled and they never did that in the other original Maytag. We had to have it fixed not long after we got it and now every time I turn it on, it immediately starts to agitate on every cycle except hand wash, which it never did before. If I knew it agitated the way it did, I never would have got it. Good thing we bought an extended warranty for this machine. We have used it once already and it looks like we may have to use it again. I am very disappointed in this machine and your workmanship. The old machines were much better and more dependable.

We have had a Maytag Bravos XL top load washer less than a year. Big Mistake. It was JUNKYARD ready when it came out of the box. Does NOT wash clean. Weve tried everything.The agitator looks and acts like a toy. Will not run enough water to wash anything. We had a LG front load before and its hard to get use to having dirty clothes. NEVER AGAIN.

Purchased dryer less than 6 months ago and now have an issue with the powder coating bubbling up and flaking off on the dryer drum. Maytag says not covered under warranty unless found in less than 30 days. If I had know that I would not have purchased the dryer.

My Maytag dishwasher Model No. MDB7759AWS1 caught on fire last night, inside the control panel on the top of the door. This was very alarming as it filled the house with smoke and caused some fire damage on the bottom of the countertop also. This could have easily caused a house fire and is very disturbing. When I called Maytag, they say this model is not recalled. In my opinion it needs to be. This is a huge accident waiting to happen in other peoples homes. Please beware. If the countertop would have caught on fire entirely, the house would have gone up in flames.

I spoke with Mike today at the customer service department at Maytag to see if Maytag would pay for the parts to repair my 04/2010 Maytag front load washer (model MHWE450WW00). The bearing assembly needs to be replaced. So, that means the tub and basket need to be replaced too. The original cost in 04/2010 was $1,088 plus tax. The cost to repair is $1,048. Maytag will do nothing since it was purchased over 12 months ago. I cant believe I just threw almost $1100 away on a washer. Obviously, there is something wrong when an appliance doesnt work after 1.5 years.

Maytag French door, bottom freezer - Water accumulating on the freezer drawer gasket. After a short period of time, mold forms which is a potential health hazard. We asked Maytag to look at the problem. So far, 3 service people have come around - each one with a solution, but none have been successful. I called Maytag again and left messages on two different occasions, and they have yet to get back to me. Am I on the blacklist? This I know for sure - this is the last Maytag product to ever get in to my house again. If anyone has a solution to our problem, we would love to hear from you.

Bought the matching washer dryer set thinking would be energy saving and reliable. Two months after warranty ended it quit, press pause/start button, no reaction. Started looking online and found out this is Maytags Frankenstein. Checked obvious stuff like power supply. Wont be buying another Maytag product EVER. Dryer still works but washer dead. Am retired, low income. Cant afford expensive repairs. Maytag ought to be eating this, not the consumer.

I have a Maytag Precision double oven 850 series. The upper oven handle does not fit snugly and has been broken 4 times. I have had to order 4 new handles because the hardware does not seem to secure the handle to the oven door. There are no problems with the lower oven door.

We bought a Maytag Gemini double oven in June 2007. It has been a problem from day one. It arrived with a damaged door. They reordered and replaced it. Through the next few months, I became very discouraged with the oven. I bake a good bit and was always used to an oven with fairly accurate temperature. This oven will not reach or sometimes just wont maintain a steady temperature. After a couple of service calls, I gave up. I now raise the temperature setting about 50-75 degrees higher that the recipe requires. Naturally, I dont always get the best results. However, that isnt the thing that really bothers me. These ovens have three ignitors. About every six months, one breaks. The cost is over $200.00 each time. The ovens/broiler are highly unreliable. After mixing up something or on an important holiday, one may find that the oven wont light. Theres no warning! It is simply gone. I will never again buy a Maytag! I called Maytag and questioned them about the lemon law. I was told that the same piece had to break three times in one year. That is crazy, when the entire thing doesnt and has never worked well.

Two months after purchasing our Maytag refrigerator, the light/cooling unit went out. After speaking with Maytag’s customer service and scheduling a repair company to come fix it, it took 3 separate trips over a span of 2 or 3 weeks to finally find the correct replacement piece to get it to work again. It is now 10 months since buying and we, once again, are having issues with the lights going out and randomly coming back on, the water/ice machine not dispensing, and we’re just waiting to see if the cooling unit isn’t out as well.I called Maytag as soon as we noticed the issue, and after waiting 15 minutes on hold, they scheduled a repair service to come check it out... in 5 days. Having spent $2300 on a refrigerator for our family, we were hoping for a reliable product. I would NOT RECOMMEND this refrigerator and will never buy anything, or let any friends or family members purchase anything, Maytag manufactures ever again. As if the faulty product itself weren’t bad enough, I have had the absolute worst customer service experience. Who would have thought it could be so difficult to look up a customer account, even after having it registered with Maytag after purchasing.

March 7th. My refrigerator ice door started flapping and the lights flickering. The next day it quit working. I called Maytag. They said they would have someone come fix it the next week. The repair service people called me back the same day to tell me that the part I needed has been on back order for 2 months. I called Maytag back. They told me to wait a week they put out an all alert for the part. I called back in a week. Now they tell me its 2 months. This is ridiculous and a huge inconvenience. I will not buy anything again from Maytag. $2,800.00 refrigerator should last a minimum of 20 years. This should be a recall. Thousands of people are having this problem.

My double oven was purchased over 6 years ago. They have been served yearly and work fine. The only thing is the cleaning cycle which if used at the high temperature to clean can affect the oven temperature control. I don’t use this function anymore.

Maytag Bravo washer and dryer delivered 2 days ago.My complaint is with the washer. I didnt know it was HE and that it requires special detergent! I didnt know the lid locks! I didnt know when I push the hot water button, the machine mixes in cold water! Complicated, delicate machine and not user-friendly. I dont expect the washer to last long.

I bought your Maytag model MDB7749SBW1 dishwasher on May 22, 2013. We bought Maytag because of your reputation...not because of price. However, in September, 2014 (2 months out of warranty!!), the control panel stopped working. I called the 800 number and the best they could do is to extend the warranty for 6 months BUT only after we paid for repair and control board replacement. This is not cheap!!! We were furious. I looked if there were recalls on this model but there is not (should be). Anyway, after we paid for repairs and a new control panel put in ($160.00 +- for part itself), we were very cautious about touching anything on that dishwasher. YOU HAVE an issue with design and I can give you link after link of other customers who have expressed the same thing. So, here we are in 2017... About 2 months ago, we noticed the exact same symptoms with the control board.In fact the ONLY way we could start the dishwasher was to turn off the breaker, let it sit for 20 minutes - overnight and then turn back on and hit the start button. We lost all control over the settings. Only auto clean and delay 2 hours were working. Yesterday, I purchased yet another control board ($179 incl tax and shipping). I plan to install myself. If I could afford another dishwasher, I would do it and never buy Maytag again. Maytag really ought to be ashamed and if they were truly concerned they would offer these defective parts at a steep discount or better yet, recall. I plan on submitting something about this issue with any consumer group I can find. I guess the only way to spread the word and perhaps force a company to respond is to post on social media anymore. This is NOT a like.

I bought our Maytag HE washer model #MVWC565FW back in July 2019 after having owned a Kenmore scratch and dent washer from Sears for approx 25 years, and in just one month of using it I knew it was a mistake. There are only 2 water levels - deep water (full tub) or practically no water (though there are a number of settings, there is no difference in water level, its just full drum or very very little water). The auto-sensor water level option is a joke - there is barely enough water to wash anything - its like going back hundreds of years to washing and beating your clothes on rocks. Items in the washer become so tangled it sometimes takes a while to detangle before placing in the dryer. Water stops filling the tub when lid is open - I can no longer wash and rinse delicates while the drum is filling. It took 3 calls w/ Customer Service to get an ADDITIONAL lid latch that I can use to trick the machine to thinking the lid is closed - I keep the actual lid open, then stick in the lid latch I bought - take it out when Im done hand rinsing. This also enabled to to view the washing in action - IT DOES NOTHING! Clothes stay in the same place as you placed them in the tub - they dont move, they dont wash - and I bought a washer with an agitator - that is in quotes because it is a misnomer with this brand! The wash cycles ARE SO LONG it takes all day to wash a few loads of laundry. Once you select a setting YOU CANNOT CHANGE IT - the washer empties and stops, then you have to start all over again - ENERGY AND WATER EFFICIENT...REALLY???? What a bunch of you know what! This is the most inflexible piece of junk I have ever had the displeasure of owning. I have to keep jugs of water on hand that I keep filling up to at least have a bit of water. When I called Cust. Svc. at the beginning telling them my experience - the person on the phone had nothing to contribute - they couldnt even tell me what cycles might fit my needs - they told me to go back to Home Depot and ask someone there! WORST APPLIANCE WORST COMPANY.

I was given a confirmation number to service my dryer. When I called the service contractor, Maytag provided. They said the appointment was cancelled and Maytag cancelled it. When I called Maytag, they said the contractor cancelled the appointment. I was never informed my service appointment was cancelled. I took time off from work and no one came. How can a third party cancel a service appointment without letting the customer know?? Is this any way to run a company and provide service? I have now taken two days off of work and do not have a dryer that works. I have never been treated so badly as a customer. My mistake was trusting that I had an appointment when I received a confirmation number. Why give a confirmation number when it is absolutely meaningless?

Very Poor Quality from Maytag Although (Dishwasher, model MDB8959AWS) - I knew Maytag always had a reputation of selling quality products I have never purchased a Maytag appliance because they usually cost more than other brands, so this is my 1st Maytag product. After ~25 months (after all warranties have expired), the unit stops working. The lights seem to have a mind of their own. I removed power from the unit for 1/2 hour attempting to re-boot the computer but the condition did not change. After researching the issue online, I found that Maytag has a two big problems: 1) Defective dishwashers, 2) Bad or no customer service.I am an engineer and this type of a problem (it happens from time to time) MUST be acknowledged and the customer made whole or the reputation of the company is destroyed and future sales will (and should) diminish to the point that the company may(?) go away for ever. I know products are not designed to last a lifetime like they were in the 60s & 70s but 3.3 years for a $650.00 appliance is way out of line. The dishwasher we replaced was ~18 years old, and we only replaced it because my wife wanted a more modern look.

Our Maytag Bravos Top loader with no agitator is headed to the junk pile after 1.5 years of BAD service. I honestly believe that whoever writes a good review on this machine is NOT an actual owner. Lets start with how it NEVER cleaned our clothes... The washer uses barely enough water to get the clothes wet. Soap remains in the clothes so the family is constantly itchy! If you add 3 additional rinse cycles, its still not nearly enough to get out the detergent and youre left asking yourself, What about the HIGH EFFICIENCY???? Next theres the issue of the water never being hot ENOUGH to kill bacteria (were back to the itchy thing). Its suppose to be an energy saver, but at what expense? Its not QUIET like promised (well maybe for the first few months). But upon opening the lid, you realize it was quiet because not a lot was happening to get the clothes clean. Now lets talk about the horrible smell... I dont know where its coming from... It occurs during the wash cycle and smells almost like a natural gas type odor. This is NOT because the washer wasnt cleaned once per month! Maybe its the bright orange RUST near the bleach dispenser or all along the inside rim of the lid... Remember its ONLY 1 and 1/2 years old. Before I get to the ISSUE that finally did this machine in... I have to mention the machines UNEVEN load response.. Brace yourself, it sounds like 1000 tribal drums... and if you dont readjust the 200 lb water logged load, it will just keep on filling up with water and draining indefinitely (so dont leave the house if youre washing jeans, blankets or sheets!). The FINALE of our machine is what I kind of always suspected it would be... the lid lock!!!! One day it stopped in the middle of a cycle and the door remained locked... After unplugging and retrying, the door unlocked, the buttons all worked, but the machine will not fill up with water or start a cycle. To be honest... I am so GRATEFUL! I get to buy a new machine and although Im pretty pissed that the machine died after just 1.5 years, we can finally have CLEAN clothes again, peaceful laundry days and get rid of the ITCHIES!!!! Bye bye FOREVER Maytag!!!!!!

After 15 months of use the Maytag Dishwasher MDB8959SBS2 the control panel start malfunction. I read very carefully about the Home Depot Customer reports before purchasing this built in stainless steel dishwasher, and supposed to be one of the top notch on the market, around $850 retail price. It becomes a big disappointment. After three months of use, the top rack handle broken but it still under manufacture warranty, so we get it fixed by Maytag contractor. Then 15 months after regular use for a family of five, the control panel start malfunction, few bottoms will not start anymore. We are out of luck with one year manufacture warranty and working towards our VISA card extended warranty to try to get it fixed.

Maytag top load 300 series washer - This is the worst washer I have owned! It does not wash items- especially sheets - without getting totally tangled up and twisted! I wish I had my old one back that lasted 20+ years. I will NEVER buy another.

Maytag washer. The worst I have ever had... Never again. The tub does not wash, swish nor spin after 2.5 years. Absolutely a waste of our hard earned money... Never ever buy another maytag again. Had a tech come out and wanted to charge almost $500 to repair it. We told him to get out and never come back.

Weve got a 3 year old dishwasher thats stopped working. First some of the lights on the control panel wouldnt light up, now only one light will light up and it wont start at all. Maytag would be better served to stick with the older mechanical switches and settings if it cant manufacture reliable electronic control panels.

I have been very disappointed with the 2017 model of Maytag washer and dryer as the washer does not clean the clothes as it should. There is the inner part taken out with no agitator and I believe that is the reason that the clothes comes out not white or cleans as I am use to it being before with my other machines. I think they need to reinstall the agitator to clean the clothing thoroughly. The dryer takes longer to dry the clothing and it uses more hydro which cost a lot more monthly for us to have to pay out. I will never purchase another washer and dryer as this in the future.

I purchased a new Maytag dishwasher (model #MDB4651awb3) for $300, in December of 2009. Seven months later, the dishwasher refused to start. Some lights on the front panel would remain on, while others would not respond. The Maytag repairman made a house call and replaced the front control panel, and vent. After the repair, the dishwasher worked fine for nine months. Then, the same thing happened again. It refused to start with the same front panel light problem. I called Maytag, and since the machine was now past the one year warranty, they wanted $275 for an additional 1 year warranty, to repair the machine. Since I can buy a similar new machine for $25 more, and felt this was now an ongoing problem, (it would be the third panel in less than two years). I expected Maytag to offer more to take care of their lemon problem. Since they refused to reconcile the situation, they obviously no longer stand by their machines. I will no longer buy Maytag/ Whirlpool machines, and do not recommend them.

I have a warranty on my Maytag refrigerator. My icemaker has been broken for six months. I have had repair people show up frequently to try and fix it. Six months and six icemakers later, it still cant be fixed. Remember, I take off work to meet these repair people who sometimes show and sometimes dont. They elevated it to the manufacturer who was going to come out and look at it on Friday, November 23 between 8 and 12. (This is day after Thanksgiving is my only day off.) He doesnt show up nor does he call. So, I called and he is running behind. I should wait until he gets here. Evidently, he doesnt have a phone. These people are totally disrespectful of other peoples time. I didnt mind waiting for it to be fixed but I do mind people who have no consideration or respect for other peoples time.

Purchased a Maytag washer for my family of 8 because we do a lot of laundry and our Samsung washer failed after 3 years. I thought Maytag was a more reliable brand and was hopeful. The machine stopped working after less than 4 months of service. Manufacturers warranty repair came out and said it needed three new parts, motor, clutch and chip - said it would be another 2-3 weeks depending on parts. So all total without a washer for 4 weeks minimum - call the customer service people (first one was rude and short), 2nd one after 45 minutes on hold - told me the were no other options other than wait for the repair. Four months after a brand new washer and it failed. I requested a replacement option and they said no way. Their hotline talks about a positive customer experience and that seems to be a joke. Not helpful, super frustrated and they do not seem to care about the customer experience at all - terrible product and service

I have a Maytag MFI2665XEW6. Im getting water on the floor by the bottom draw. It looks like the coil in the back is freezing up and then melting down to the bottom of the freezer and out to the floor. I dont know how to lower the temp on the door panel.

Ive had a Maytag washer and dryer for 10 years. They have worked well, havent had any problems. I bought Maytag because of their excellent reliability, which has proven true. Design is not as modern as others, and doesnt have all the features, but overall solid reliable washer.

I have trusted Maytag for many years, more than 60 years, my parents and then myself. My Dad always told me I could trust Maytag over any other brand and that has always been true until I bought a new Centennial Econoserve Washer. This is without question the worst machine ever made. I should have asked every question in the book concerning this machine but, oh no, I just trusted the name MAYTAG. I am so sorry. I cant trust it to clean anything that shows it needs cleaning so you have to wonder what does it clean that you cant see. Im sorry people, I just dont know what to do. I cant afford to buy a new machine and the store I purchased are basically telling me, Sorry, you bought a stripped down model. Too bad! I will never buy another appliance from that store nor will I recommend them to anyone. Too bad since they are locally owned. Anyway, Maytag, you blew it badly to turn out this terrible machine. Thats my story and Im sticking to it. Better product next time.

I think so much about Maytag dishwasher with electronic controls that I decided to fix up my Maytag mdb3700awx by replacing the motor. It has an old fashion timer. It was trouble free for 10 years until the water supply line fail and sprayed water on the motor and shorted it out. I got a use motor and pump from eBay for 40 dollars. The dishwasher should last 20 more years. Too bad Maytag dont make them like they use to.

We bought a Maytag refrigerator serial # K11101146 and model # MBL2258XES1 on 5/7/2011. We started seeing puddles on the floor about a month ago coming from the bottom freezer. The warranty on the refrigerator was only good for a year. We investigated it further online and saw that a lot of other people were having the same problem. We found a video on Youtube on the solution, which was to tear the bottom frig apart (which is a pain and takes about 3 hours to complete) and to thaw out all the ice accumulated on the coils and run hot water down the drain until that thaws out. It makes a real mess. Now we see that this will probably have to be done again and again from others online who are having the same problem. We never had this problem with any of our refrigerators or any problem with them for that matter. Our last one was a 15-year old Amana and we wanted a more energy efficient refrigerator. We bought this one at Home Depot thinking that this one would last us for the rest of our lives. We are in our mid 60s now. This should not be happening at all especially as much as we paid for the refrigerator. I contacted Maytag and they more or less said, “Sorry about your luck.” I hope something can be done about this, especially for the amount of complaints filed. Unfortunately I did not take pictures but if it happens again, which I understand from other complaints that it will. Thank you.

Owned my Maytag Maxima front loading HE washer for just under 2 years. Went to turn it on one day and got an error code that I later found out meant the computer board went bad (a very costly expense). I called Maytag and explained that a $1200 washing machine should last more than 23 months and if they stand behind their products they should do something to cover this repair. Even after speaking to a manager they told me too bad they couldnt help me. But they would be happy to sell me a $350 extended warranty.... Never again Maytag/Whirlpool!

This Maytag (1979 model) is about as good as other dishwashers (I always rinse before placing in machine). It does have a lot more buttons that are not used than the last one I used (installed in the 1950s). Delayed start, choice of preheating water or not, choice of drying. Not big enough to do everything when have company and too big to use when no visitors present. When I am alone it takes 3 months to get enough to fill the machine and by that time they are getting moldy so most of the time I wash by hand. Black glass front with imposing row of controls across the top. I normally do not generate enough dirty dishes to warrant having a dishwasher. Since my wife died I have used the dishwasher two to three times a year.

Should have read reviews. Ill never buy another Maytag. This stove has been bad almost from start. Stove has burned marks from using broil. Repairman told me not to use broil anymore. One of eyes has been worked on 2 times; the knob does not work correctly; when you turn off, it goes past the off and keeps on going to the left. It is very hard to clean surface. I have had a few years. Company paid for one repair. They should have replaced stove from beginning. Not safe.

I purchased Maytag gas range in March 2011 at Home Depot, Model No. MGR5605WWO. I received the product in May 2011. The porcelain on the grates chips away leaving large grooves in grate, which affects cooking efficiency, (the fire burns erratically). First, I called 1-800-688-9900. The grates were replaced. And then same problem, it was replaced again, and again the same problem. The warranty to cover stove was extended by 6 months. The enamel on the round magnetic cover for the burner is also chipping away. I was told that this chipping of the enamel is a cosmetic problem and does not affect the functionality of the stove problem.A repair technician was sent out at my request to see firsthand the problem grates. I was told by him that if it occurred again, the manufacturer needs to be made aware of the defective grates. He noted that the enamel covering on the grates was not uniform. I have been told by Maytag supervisor today that she will get back to me within 3-5 days and let me know what is going to be done. I have had gas ranges before, but this is the first time this problem has occurred and its continuation is unacceptable. Is there anything further I can do to ensure I have stove grates that do not chip continuously?

Bought this Dishwasher two years ago. Control panel was working intermittently now it does not work. I am looking for anyone with this same problem. I know lawyers who are class action specialists who fight for the consumer. We need to make Maytag responsible for the flaws they have in their product. From reading these other reviews it seems that this control panel issue is consistent no matter what model you have. They must all share the same electrical components that is causing this issue with the control panel. My model number is MDB8959SBS2.

We purchased a high-end stainless steel interior/exterior unit in January 15. It is now July 15 and we have not been able to get any use out of it. Day 1 washer leaked. Full day off for service. Guy told us we were using the wrong soap. It leaked on the very next wash. Called again. They forgot to check the soap dispenser. Another service/day off. Leaked again! Another service call/day off. They replace the dispenser & seal. Now washer no longer leaks but the dishes are dirty and wet even days later. Another service call. Another new part. And now we are waiting for our 5th service call. We paid for a new unit and have a refurbished cobbled together piece of junk. Maytag stubbornly refuse to replace this unit.

Maytag Dryer MED6000XR2 - Purchased in Sept. 2012 - first service call 1/13/14; 2nd service call 2/20/2015 and less than one month on 3/14/15 it goes out again. It takes one week to get service company out and then another week for the part to be ordered and put in. This means I am without a dryer for over 2 weeks. An $1,100 dryer goes out every year and sometimes within one month?! According to the service company, it just is the way this dryer works. Really? If Maytag ever wants my business again, I better get a more justified reason and better than 2 weeks service call. This is absolutely ridiculous.

Have read others reviews and experiences and wish I had visited here first. Our first Maytag washer and dryer set lasted over 25 years with only minor repairs until the transmission started to leak grease and was uneconomical to repair. Our second set only lasted nearly 10 years and were obviously lesser quality. The wife decided that she wanted the best and high tech version. She really liked the features of the Bravos 300. What a mistake! Not even three years old and she has been dealing with the noise and the problem with constant unbalanced loads, intermittent error codes, odors and the forever cleaning requirement. The whites were intermittently getting rust stains until I determined that the underneath side of the top cover around the bleach reservoir had rusted out big time. I replaced the top cover for over $125 plus an afternoon that I will never get back. (Out of warranty, of course). Today the wife called me to say that the washer would not complete the rinse cycle and she could not reset it. We had to pump out the water and pick the wet clothes out. A grinding sound is coming from near the bottom of the machine and sounds expensive. The service man is scheduled to be here day after tomorrow to give me the bad news. My next washer purchase will NOT be a Maytag or any other high tech piece of crap. Simple is better.......

We bought our $600 Maytag dishwasher less than two years ago and have had three separate problems with it, from faulty instillation, to a faulty seal to faulty control panel. The first problem was covered under warranty, the second problem we fixed ourselves and the third problem, nothing can be done except pay an additional fee of $250+ for a new part. Maytag used to be a good name but with three problems in under two years, the only guarantee given is that if you buy one, be prepared for problems. This company does not stand by their products and will only ask for more money to fix their faulty items.

MAYTAG REFRIGERATOR SAFETY ISSUE SHARP EDGE Maytag refrigerator model MRT118FFZ01 purchased Feb.2018. There is a safety issue, sharp edges. Maytag has been aware of this for over 1yr from customer reviews. I went to consumer affairs.com and there are numerous complaints on products/customer service. I have been asking for a replacement door since Feb. On Sept. 7th I cut the palm of my hand on sharp edge, drew blood, no stitches but I was very upset. Called Maytag, transferred to the safety dept. sent out service tech. He reported that it was a safety issue, very sharp edge, he had to put duct tape on corner to prevent any more injuries! He requested that new doors(freezer&refrigerator door) only be sent, I do not want/need the whole unit replaced. Freezer door has sharp edge also. I have numerous emails to/from corporate office begging since Feb. for a new doors so that this would not happen! Maytags solution is to buy back refrigerator or I should pick another model. Neither is a solution for me. I picked this model for a reason. I asked them to provide me with the simplest solution which is to contact factory where it is made, red flag it, talk to manager, quality control check to see that there are no sharp edges before it is shipped to me. They refuse to do that 1 simple common courtesy, customer service request! They cannot guarantee that door will come without a sharp edge! My model is not the only 1 with this problem. I talked to salesman & model in store has sharp edge & in the reviews the same model had sharp edge which was submitted over 1yr ago! So Maytag has been aware of this safety issue for some time now but chooses to do nothing about it! I chose Whirlpool because of the name, I thought it stood for quality & above all excellent customer service. Was I wrong, found that out thru numerous phone/email conversations. They just dont care! Is it too much to ask Maytag to give me a refrigerator with no safety issues?!!! I have talked to Aaron in the corporate office, he was no help at all. His # 866-817-5404 ext **. I have all the emails to/from him. Please help, I want this same refrigerator, only model that would work for me. Now that I have had personal injury & have spent so much time/effort, aggravation since Feb. trying to have them do the right thing I feel that I am due monetary compensation. Bottom line this complaint is concerning a safety issue & horrible customer service from the call center to corporate offices! The Maytag name isnt what it used to be known for, quality & service.

We purchased a complete, upper-end Maytag kitchen package from Lowes. So far, the MMV5208WS microwave has gone out 3 times; it was the magnetron all 3 times. The last time was a few weeks after the warranty ran out. After a lot of discussions with Lowes management, they then took it back and gave me choice of any brand. We picked a Samsung and have had no problems so far.As for the MDB8859AWS dishwasher, it was just stuck under the counter for the first 6 months of its life, because we were in the middle of a remodel and it wasnt plumbed in yet. Once we got it working, my wife loved it. Weve used it maybe 40-50 times since she was still hand-washing small sink-loads of dishes. A month or so out of warranty, it went out. There were no lights on the keypad and everything was dead. We thought it was the main control board, but it wasnt. Next, I tried the keypad, because Ive read many posts about these 2 things seeming to always go out on these models. I still have the fridge and stove, and hopefully they fare better than the microwave and dishwasher.What kills me is when I look at my old Maytag dishwasher and Samsung counter top microwave in the garage; both 15-20 years old and still worked just fine after getting replaced. It has never had a repair of any kind. I went out and spent $639.00 (it was on sale, the regular price was $799) on a ** dishwasher and it didnt even last a year. The microwave was close to $400, and it was on sale. I think my old Samsung microwave cost $79.99 when I bought it. You used to get what you paid for!

In 2016 I purchased a matching Maytag washer and dryer. The reason why I purchased it because I was in a house and I no longer had a washer and dryer and I refuse to go to a laundry mat at the city to go to Nebraska Furniture Mart and it was a number of different washer and dryer combinations available. I had previously own a Samsung matching washer and dryer and it worked fine, my Maytag has dame of the same features and works great.

Bravos XL washer- This is probably the worst purchase I have ever made, first off, at $1000 it was a pricey purchase however, I chalked it up to it will last many years without issue. After only 3 years, the unit leaked water and was so loud you couldnt stay indoors while it was on spin cycle. The bearings and seal were completely shot and needed replacement, after the sticker shock of having a good repairman fix the problem I decided to tackle the job myself. (Thank you YouTube). All was well for the next 2 years until it all happened again. Maytag is junk and will never get another dollar from me-ever! A Speed Queen TR5 now sits where that piece of crap used to reside. BUYER BEWARE!

In October of 2012 we bought a Maytag Refrigerator Model MFF2258VEM. In the spring and summer of 2014, we noticed puddling on our kitchen floor. We thought it was our dishwasher or sink since the $1800+ fridge was new, but couldnt find the problem. We travel a lot and are gone for extended periods. When we returned in winter of 2014, we discovered that there was substantial puddling and found a sheet of ice in the bottom of the freezer compartment. We did research and found that this is a common problem with all the bottom-freezer Maytag models, which then leak. We discovered that the leak had seeped into our kitchen sub-floor and was destroying all of our kitchen floor tile, causing cracking and breaking, a renovation of just a few years previous that cost a lot of money. There was NO problem with the floor until we put in this Maytag refrigerator. The remedy for the leaking is constant maintenance and a lot of work, totally ridiculous for a product that costs so much. I want to sue Maytag for both replacement of the refrigerator and the cost of replacement of my tile floor. Can someone please advise? Thank you.

While washing clothes in my Maytag front load washer, I noticed that there was water leaking from the front left corner from the bottom. I have owned the washer for only 2 years, and Maytag manufacturer (Whirlpool) told me that it was going to initially cost $80.00 for a service call and then more money to fix the leak. WOW. Also the wood floors that are underneath the washer and dryer, is starting to warp from the leaking washer. I would recommend DO NOT BUY A MAYTAG APPLIANCE. The warranty is basically worthless along with the washer.

I purchased a Maytag front loading Epic z washer and I paid a great deal of money for it and now I have a broken part on it. We contacted the Maytag manufacturer and they have informed me that the part would not be available for up to two months maybe 6 months. I cannot afford to buy another washer, so now I have a broken washer and need to purchase another washer until the parts come in. I would not recommend this washer or dryer to anyone ever.

I bought my maytag stove model MGR7662WS on January 30, 2011 and have had it serviced 3 times... same problem. I set oven to 350 degrees, put food in oven and later check on food only to find the temperature reads 350 but the oven is cold. Food is not cooked and it smells like gas. I turn it off and turn it back on and it does not turn on most of the time. Service guy keeps replacing parts and says he will replace the same part he just replaced last week. He says sometimes the part comes out defective. I think the stove is defective and I have thrown away so much food because it does not finish cooking and smells like gas. Its so frustrating because my Thanksgiving was ruined two years in a row due to turkey not cooking.

I just bought my Maytag Range model #MGR8700DS2 in August 2016. Bought Maytag because I always thought it was one of the best with the best warranty around. Now I am not so sure. After using it the first time, found that when you are baking anything in the oven the burner control knobs get very hot. That is because they designed the knob area to be right above where the heat vents out from the oven door. The knobs get so hot that you almost burn yourself if you touch them. This is a bad design in my opinion especially if you have any kids around. Even the sides of the oven get way too hot. This is also bad because of the tight spacing to your cabinets. I contacted Maytag about this and got a OH WELL kind of reply to my problem. You bought it and you are stuck with it. I would not recommend buying this model to anyone.

I purchased an LG (white) washer last year, but my husband upgraded all appliances to stainless, including Maytag washer and dryer. The washer does not fill with enough water to cover the clothes. It barely agitates them to wash. Some clothes even come out with dry spots on them at times! They smell and are still dirty when done. I have tried every setting hoping that was the issue. Normal, power wash, none work any better! Had to resort to the soak function which does not add fabric softener or drain the water completely. Thankfully I didnt sell or get rid of the LG. Putting the LG back in asap. Nevermind the mixed color finishes of white and stainless between the washer and dryer. Clean clothes most important! Piece of garbage and complete rip off!

Oven is not even 2 yrs old but, the bottom oven floor lining is crackled & flaking. Although they say the cavity is covered under the 10 yr warranty, they say its not covered. Basically told me theres nothing they can do for it. I bought all Maytag appliances for my new home because they claim they stand behind their product. The 10 yr plaques on the appliances are a joke. So disappoint.

My Neptune dryer purchased in November 2005 had the drum crack at about three years old. I complained so much that they finally agreed to send a replacement drum for free. Now, two years later, the drum has cracked again and tore through the housing on the front of the dryer. The repairman said it would be too expensive to repair. Consumers, beware.

This range and oven get unsafe, very hot on the surface and sides. Also, first time we used the oven, our oven mitts and bbq tools caught fire in the storage drawer.