In October 2016 I purchased a New Maytag washer (Model# MVWC565FWO) from LOWES. I bought an extended 5 year warranty with it as well. I have my invalid, totally incapacitated Sister living with me. The situation requires several loads of washing each day due to her conditions. TWO WEEKS after starting to use it we began having issues with the washer. It would stop in the cycle, lights flashing, only way to restart is to unplug it, move control from wash cycles setting to drain and spin... then within the next 3-4 loads it would do it again. Sometimes it sat for awhile I would smell like an electronics Odor getting hot... I called Lowes. They replaced it. Approximately 3 weeks later the NEW washer began doing the SAME THING...Lowes would not replace it with a different Model or brand... only send a repairman out. Long story short, he has been here 4 times, replaced the Computer Control with NO IMPROVEMENT!!! NOW Lowes is sending him out again and saying that if this doesnt fix the problem they will refund my money... My problem with it all is this... IF MAYTAG is having these type issues, WHY PRAY TELL, has a recall or solution been found and passed on to the repair folks??? I bought this Maytag due to #1 Reputation, #2 It was Assembled in the USA, NOT South Korea like the Samsung with recalls... Now all this is going on. I WANT A WASHING MACHINE THAT WORKS RIGHT!!! This is totally unacceptable and totally uncalled for. WHY could these Govt agencies and Manufacturers not LEAVE the washers alone? Computer technology... PLTTT. The old timers controls gave no problem in over 40 years of using them. Now this crap.

I bought this washer from Home Depot and was told I could load large comforters and even sleeping bags in it because there was no center agitator. There NEVER seems to be enough water to wash and rinse clothes completely. The water saver feature cannot be used as I have to use extra rinse cycle EVERY load to rinse soap out of clothes or I get white residue spots. I have MANY MANY shirts that have small tears in them I believe caused by this washer. I have monitored shirts I put in the washer and again today lost another high quality fabric T shirt. I have saved all of the shirts in hopes that one day there will be a definitive report that this washer design stresses clothes and damages them. I am going to purchase a new washer and it will not be a model like this.

I purchased a Maytag dishwasher model number MDB7749SBM in May of 2013. In August the dishwasher control panel stuck on Rinse only cycle. It has been stuck on this cycle for a month. I contacted Maytag and they walked me through a reset. It has not worked. It looks to me as if the control panel has failed. This seems to be a common problem with the Maytag dishwashers. As soon as the warranty expires, so does the dishwasher. I purchased this dishwasher from Home Depot for over $600 thinking I was buying a quality product. My previous dishwasher was also a Maytag, even a lower end one that lasted almost 14 years! This one has not even lasted 14 months!!I was told by Maytag that I could purchase an extended warranty for $267.45 that would last a year. I believe, 4402 based on other reviews that I will be dumping more money into this one even after that. Very disappointed!! I will never buy another Maytag product again! I should have bought the Bosch. It was roughly the same price and high quality. I bought Maytag based on my previous experience. No More!!

We purchased Maytag microwave (MMV4205DH1) less than two years ago. Within the first year, the microwave would not work and we would see an Open and Close Door message. We had it repaired and now 10 months later it is doing the same thing. The cost of repairs is high--the same as a new microwave. We have been inconvenienced throughout the holidays by our broken appliance. Disappointed.

We bought a new home with all new Maytag appliances. Our Maytag dishwasher has had 3 new handles, 1 inside tub and now needs a new touch panel. Our Maytag oven/stove has needed three ignitors and the oven door has never been right! The microwave is the only appliance that we have not had a service call. Appliances are expensive along with parts and labor for service calls. I will not be purchasing any more Maytag appliances. The standard comment by repairman: They dont make them like they used to. How sad is that!!

We purchased Maytag dishwasher model #MDBH989AW53 in January 2010. June of 2012 the control panel died. Luckily, we had the extended warranty. The service company came and replaced the panel. 3 weeks ago, the panel died again! The service company replaced the panel again. Today I got home and the dishwasher is completely dead! I am so furious!!! At this point, I may just have to bite the bullet and buy a brand new machine. This should NEVER happen to an appliance that is so new! What a laugh regarding the Maytag quality! It is the WORST I have ever seen in my life! Stay away from Maytag!!!! Buyer beware!!!!

I have a Maytag dishwasher model mdb6759aws3. The control touch pad broke after 1.5 years of light use. It costs $475 to fix (includes labor). Completely unacceptable service provided by Maytag over the phone. The only concession offered was a 25% discount if I bought the replacement part (control touch pad) from them. After some internet research, I learned Maytag marks up their parts prices over 25% so they are really not giving you a discount at all.I filed a complaint with Maytag but they were unable to provide me with any evidence of doing such except for an 11-digit code. Due to a major defect, Maytag should have sent me the replacement part for free. I told Maytag I thought this was fair and that I would pay for the labor. I will never buy another Maytag appliance again! They are junk and the company does not practice common sense customer service.

MF12665XEM7 - Maytag Refrigerator purchased from Home Depot. We initially thought it to be a good value until it started leaking puddles of water onto the floor to the front sides of the bottom freezer drawer. This event repeated itself and I feared the water would seep between the floor tiles and begin to degrade the sub flooring or possibly cause mold as well. Upon further investigation of lying on my side and pulling the bottom drawer open, I felt, what I thought to be ice on the bottom of the refrigerators floor. I gently inserted a smooth butter knife and with a nudge, a whole sheet of ice about one half inch thick, lifted from the refrigerator floor. I have since had to repeat this about every three weeks or so. Im nearing retirement and shouldnt have to lay on my floor like this to protect my floor and to keep my wife and I from a potential hazard of a slip and fall from this water on the floor! Dependability People? Hardly! I think they got outsourced! Im disgusted! Thank you!

I bought Maytag Bravo washer and dryer set in Nov 2012. Washer door lock broke shortly after 1 yr and now the gearbox has broken. DO NOT BUY MAYTAG BRAVO WASHER. The cost to fix is more than the value. Before the gearbox death the sound it made while spinning was so loud you could not hear the TV or have a conversation in the west end of the house. Visitors were stunned at the noise it made. I called Maytag warranty and explained I am having the same issues as everyone else, what are you going to do? The answer was nothing. Please read the other reviews, same issues. It never cleaned clothes anyway, bad design, bad company and bad corporate values. Model number MVWX700XLE.

I bought this machine a year and a half ago. The entire drum and spin motor need to be replaced. Maytags warranty only lasted 1 year. I bought it at Home Depot, and also purchased the extended 5 year warranty. The extended warranty is as bad as the washing machine. I am now just 2 days shy of 4 weeks of trying to deal with both parties. Ive had to take my laundry in to have it done. The cost of the laundry, the cost of the machine, and the cost of the warranty is more than $200 more than what Home Depots Extended Protection Plan is willing to reimburse/refund. Home Depot does as much as Maytag when it comes to standing behind what they sell. An $800 washing machine only good for 18 months, really???

We bought the Maytag 2000 series washer and dryer stackable set in 2012 from Home Depot. My husband was smart enough to buy an extended warranty and year after year we renewed it. Guess what?? Year after year the dang washer broke. This machine was a nightmare! Now that the drum spider is broken they will not honor our warranty but want to give us $300 and guess what? I cant find a replacement for my good working dryer. We bought this set because we live in tiny space and needed them stacked. Maytag really put us in a corner and we have no money to replace both appliances. Horrible customer service. Horrible machines. Just a horrible situation. We dont know what to do.

Ive only had my Maytag Bravos XL Washer for two years and I HATE it. It constantly gets off balance during the rinse and spin cycle. What should take 30 minutes takes triple the amount of time. My washer is in the basement and I constantly have to run up and down the steps to readjust the clothes in the washer. Ive started to just stand by the washer now during the rinse and spin cycle. What a waste of time. I would not recommend this washer to anyone. Also, it does an awful job of rinsing out the detergent and softener. All of my dark colored pants have detergent and softener residue on them after they come out of the washer. Ridiculous!

I hate my new Maytag washer and wish I had never purchased it. Theres no way to control the water level in it, and on sensor mode, the clothes are barely wet and rubbing against each other creating wear. Things come out with soap stains and twisted up so tight that I dont believe water got close enough to the dirt to carry it away. Dont waste your money.

Maytag washer leaves clothes more wrinkled after a wash than they were in before being cleaned. And these are not full laundry loads. Then using the Maytag dryer is a joke. Need to run double times or extended times on most of the settings to get them completely dry. When it comes to the wrinkle free setting... what a joke. Clothes might be close to dry but wrinkled. Have always had Maytag products since forever. Tried Samsung for the last set-----washer lasted 6 years and then needed a full overhaul. Cheaper to buy a new set. Went back to Maytag. MISTAKE. Samsung did a lot better job of washing and drying. Now stuck with Maytag until... when? Retired and dont have the funds to get new replacements. Just my opinion though.

This Bravos 300 washer has never cleaned clothes adequately. I have 3 sons who are athletic and this washer does not clean sweaty or dirty clothes even with extra rinse. Now my machine is 4 years and 3 months old and it needs a new bearing which will cost me $385. The repairman said this is a common repair in this machine. Maytag should be ashamed of the poor quality of this machine. I am now looking to by a new traditional top loader. These HE machines are a joke. I am contacting them to make a complaint and see if anything can be done.

Bought Bravos XL washer/dryer from Home Depot in November 2014; installed 12/8/14. First repair was in March 2015! Clean machine cycle quit working properly on 3rd attempt. Bearings were replaced, tub was replaced and main board was replaced all before May 2015. Wash load constantly becomes unbalanced if more than 3 bath towels are in the load or more than 2 pairs of jeans. Can not start a load of wash and leave home because the machine will start bouncing and rocking when unbalanced and will shut down after it tries to self-balance 3 times. You end up with a load of twisted up, totally wet mangled clothes. Maytag refused to replace the machine and Home Depot continues to sell this junk to unsuspecting buyers. Wish I had looked at reviews before I bought this model. Worst $1,200 Ive ever spent. I have always bought Maytag appliances--refrig, stove, dishwasher, microwave, other washers--but Maytag has lost me as a customer after this experience with them. Terrible design and poor customer service for not standing behind their products.

We are on our 2nd Bravos XL. The first washer lasted 6 years and there was a part going out that kept making it stop in the process. Basically the repair guy said it will just go out one day so it was up to us to repair or replace the machine. The machine didn’t have an agitator and we had been having issues with white residue on the clothes for a long time but thought it was related to the other part. So we bought a new one, with an agitator. It was the new model. We’ve had it around 6 months and we have lots of issues with the white residue. The only success we have with not getting white residue on darks is using deep fill and very little detergent. We use powder because the liquid makes dark spots on our dark clothes. So either way, there’s a problem. So we are using a lot of water when it’s supposed to be water saving. And we are using much less detergent that the company says. I think it’s the machine that has problems. I’ve read a long thread on Facebook and it appears that Maytag tells you to use Affresh regularly. It also says to follow their instructions. But everyone seems to follow instructions but Maytag takes no responsibility for their product. Makes me sad because Maytag was the best on the market at one time and we will never buy again. Our dryer works fine but the washer sucks. And that was a lot of money that I paid. I hope that Maytag decides to make it right and help their “customers” enjoy their products once again.

I bought a Maytag Centennial Top Loading washer 2-1/2 years ago. Its worked very well, but has started to roar so loud on high-speed spin that you have to leave that side of the house to be heard. The factory technician determined that it had a bad gearbox and that it wasnt anything I had done that caused it. He told me it was going to cost more for parts & labor than the machine was worth. I called Maytag and was told they wouldnt help me because it was after the one-year warranty. When I asked for a supervisor, he offered to pay for the parts, but not the service. Thats kind of like Chevy offering to pay for the defective engine part, but not the installation. I have never bought a major appliance (or even a hair dryer) where I thought 3 years was a reasonable life expectancy. Lifelong Maytag Customer has left the building.

My washer is new, out of warranty, and about 2 and a half years old. All of a sudden, with no warning or previous issues, the computer board in the washing machine malfunctioned which caused a humming noise, it would not cycle into the next wash phase, the time would go up instead of down, I could not change cycles, and when I would push the power button there would be a delay of power coming on. I unplugged and called my local appliance repair and he said he sees problems with this model regularly, although not always the same issues.Before purchasing I scoured the internet for reviews on different units to make sure I didnt get a lemon. I think Maytag saw the error of their ways quickly and stopped making these before people caught on. This model is no longer being made. I like matching units, so it meant either shell out $500 for replacing the board, or replacing both the washer and the dryer that still works, which would be about $1200 or more for a new set. I chose the least expensive route for now. Not that it matters where I bought mine, but Home Depot and it was on clearance so it was a good price. I have now made up for that difference in repairs.

We purchased Bravos series Maytag washer and dryer. These are a match pair, the top loader, extra large capacity, very top of the line, $$$$$. The washer has already been replaced after many repairs, but the replacement new Maytag leaves a powdered gray residue on all the clothes because of the small amount of water it puts in the washer tub. Even on the deep water cycle, if I put in a blanket it will come out of the washer half dry where water has never reached it. This washer is the worst I have ever seen and cost top dollar. Maytag says nothing wrong but when I show them the powdered residue on the clothes they refuse to answer. This is the worst engineered washer ever, tangles the clothes terribly, does not clean the clothes and usually forces you to wash them twice to removed the soap residue left on them. I have tried every soap on the market, stacked clothing as Maytag suggested, tried various tricks Maytag has suggested, but nothing stops the grey soap residue. This washer cost almost a $1,000 for just the washer, it is a disaster. I have asked Maytag to refund my money but they refuse. If anyone else has their washer - we need to join in a class action lawsuit to force Whirlpool, maker of Maytag to replace this piece of garbage!!!

My mom decided to splurge on a new Maytag Bravos washing machine and matching dryer thinking that at age 80 the machine would outlast her. But no. After 4 years and just past the warranty, the timer started going crazy. The repairman recommended a $250 motherboard and $90 pump and $500 labor (yes he is next on my list) and it still does not work. I WILL get her money back for the repair and we will NOT be getting a bravos to replace it.

Topload Maytag Bravos washer sounds like a jet on spin cycle. Called Maytag, no recalls or service issues. Just wanted to sell me a service contract for over 300.00 dollars that would fix it and be covered under warranty for a year on anything that went wrong. Could set me up with a service call, but it was six days from now - no thanks. The washer this replaced was a Sears which was 26 years old. It still worked and I sold it for 75.00 dollars. Guess I will stick with Sears!

In April 2010, I replaced my washing machine (still functioning after 12 yrs) to upgrade to what I believed to be the top of the line Maytag Bravo 5.2 HE washing machine. Module # MVWB850WL0 type: 580-02. This machine of 3.5 yrs leaks underneath and after having the service tech come to look he advised me it will cost over $800 to fix (I paid over $900 for this unit). He says its the bearings and went on to ask me if Id been using the HE laundry soap (as if Im an idiot) and went on to ask whether Id been washing bedding. SERIOUSLY?!? !... After much research on this issue, I discover that there are similar complaints all over North America. Very disappointed and I want this lemon replaced by Maytag.

MHW60X - I experienced a problem in May of 2015, and the repairman told me it was the master board, and he has seen this many times. He said that the MCU board goes out after 3.0 - 3.5 years!! This is exactly how old my machine was! The cost to repair this was almost what the machine cost, and this is unacceptable. I have had Maytag washers my entire adult life, and my prior one lasted approximately 20 years, but after this I am not sure I will consider another one in the future. To have a major part burn out soon after the warranty expires should not happen. I contacted customer service to find out the experience and reported problems on this model, but could not obtain any information, other than they have received calls about this model. I asked Maytag to reimburse me for the part - at a minimum, and they refused stating it was out of warranty and they could do nothing. Apparently they do not care about their reputation anymore, which is sad, since they used to be so well regarded!

Should have read reviews. Ill never buy another Maytag. This stove has been bad almost from start. Stove has burned marks from using broil. Repairman told me not to use broil anymore. One of eyes has been worked on 2 times; the knob does not work correctly; when you turn off, it goes past the off and keeps on going to the left. It is very hard to clean surface. I have had a few years. Company paid for one repair. They should have replaced stove from beginning. Not safe.

Ive had this washer and dryer set for only a couple of years and nothing but problems. The latest is that it sounds like its going into orbit on spin cycle. I cant believe the poor quality of these appliances. Ill never buy Maytag again.

I just want to give an update on my frustration with Maytag dishwasher I wrote about on July 16. In the end, I found a DIY solution and fixed it. I wrote an instructables here: **. Not recommended if you dont feel comfortable repairing things. However, the diagnostic test at least can give you some clue whether its the control panel or control board is at fault before replacing both. Thanks.

We received our new Maytag washer MHW8200FC on Saturday 11/18/17. We washed 2 loads on Saturday and on Sunday it didnt start. Not only did it not start but it was locked with clothes in it. We finally got it to open but it wouldnt start to wash. We had the distributor, Warners Stellian, schedule a service tech. He came out on 11/21/17 and determined the board was bad and that he would order one and be back on 11/29/17. A week without a washer doesnt work for a family of 5. This isnt like a lawn mower I use once a week, we use it daily. Whatever happened to quality control? A brand new expensive product breaks in 2 days? Maytag says its Made in the USA, which Im all for... Only if it works. USA or China, broken is broken so I dont care where its made. Whether its planned obsolescence or just a plain faulty product, Maytag is now another brand that I will avoid buying in the future.

Stay away from Maytag Bravo washer. We bought one a year ago and fought with them this whole year. It leaves lots lint on clothes. Weve had 2 technicians here 4 times. Now they finally said we can replace but will only get a prorated credit even though its been junk since day one and we contacted them immediately. If we wouldve known they wouldnt stand by their warranty we wouldve hauled it back to store for full refund. They dragged us along a year and now warranty is no good but they will prorate. Not fair at all.

We have had our Maytag dishwasher for more than two years. Heres how it stacks up: Energy Star rated-Yes; Noise-Almost inaudible except when water runs; Length of Cycles-long except for quick wash 59 minutes; Interior design and loading - 10 out of 10. This is the easiest dishwasher to load and it holds an enormous amount of dishes of all sizes and shapes. Adjustable and removable racks-Yes both. Everything fits including my barbecue and oven racks! Amazing. Stainless interior-Yes including silverware rack. Cleaning- 10 out of 10. Even on a quick wash (59 min) cycle this dishwasher cleans everything! I run a longer cycle just to sanitize if we have sickness in the house. Otherwise it is 59 minutes to finish. Drying-Like most dishwashers this one is only so-so in the drying department, especially on the short cycle. Without plastic containers or utensils the machine dries more completely. However, the amount of moisture remaining after a quick or regular cycle is minimal. The water tends to pool on bottoms of glasses and plastics mostly. Easy to dry by laying a cloth across top rack. Dries in just a few minutes.My only suggestion to Maytag is to work on drying technology to make the machines more efficient and effective. However, that being said, I wouldnt trade this machine for any other. It has every feature I love and a 10-year warranty on parts as well! My machine cost around $600.00. It was neither the top nor the bottom of the line.

We purchased a high capacity washer (MVWB835DW), along with the matching dryer, two years ago from Lowes. This review is not about Lowes. They did the best they could to make things right. The review is about the Maytag washer (made and serviced by WhirIpool). It has been nothing short of a debacle. The first two washers did not work and had to be replaced. The third and current washer has been repaired three times, including the drum and motor. We have been without the use of the washer for over a week each time while waiting for parts and Whirlpool to approve the repair. The washer is not high capacity as advertised. Filling the drum even half way results in the washer stopping mid cycle whereupon we have to adjust the contents back into balance. In addition, the machine leaves a lint residue on dark clothing that has to be wiped off by hand. We have asked Maytag/Whirlpool to replace the machine but they say it has to fail for the same issue four times in order to qualify for replacement. We are done and will purchase another washer from a different manufacturer. It’s easy to understand why Samsung and LG have become such a dominate force in the laundry sector. Whirlpool/Maytag does not care about you or the problems with their product. Buyer beware!

We purchased a refrigerator in December 2010 with a 12-month warranty. Since the refrigerator was delivered, we have experienced nothing but problems. Most recently, there was a problem with the auto defrost causing us to lose all our food stored. It also caused water damage to our floor. We scheduled maintenance with a contracted company through MayTag. After three scheduled visits, which made me miss 3 and a half days of work resulting in an additional loss of over $300, our refrigerator is still broken and they just want us to schedule another maintenance visit. When calling Maytag customer service we are literally told, “your loss, there is nothing we can do to resolve your issue, we can only continue to send out maintenance.” I am so disappointed in this company, the product, the customer service, maintenance service etc.

Purchased a Maytag Dishwasher (Model MDB7749SBBO), total with tax $590.34 on 3/31/13. It wasnt a cheaper model, had stainless interior. Owning it after a 1-1/2 year, the Control Panel went bad. Maytag offered me for $267 for repairs and 1 yr warranty. Why thats about half the price I paid. My personal repairman told me the cost would be around $200 to replace the control panel. Why I could get a more inexpensive model for $300 and still get a year warranty. Very disappointed in Maytag quality of their product.

We purchased the Maytag dishwasher model # MDB4949SDZ almost one year ago. Since the beginning there has been a smell to our drinking glasses when we put drink in them...smells like boiled eggs. We have always used Cascade dishwasher pods, but suddenly our dishes were being left with a gritty feeling film on them and I had to run them under water to rinse them after taking them out of the dishwasher. This model showed on Lowes website that it has a food grinder, but it cannot even get rid of a single kernel of corn that might get left on a plate. After a load is completely washed and you open the door, there is a strong smell of detergent. If you run an EMPTY dishwasher with NO soap it creates an abundance of suds like there is still soap all in the tub!!The repairman came out and called Maytag and they ran a diagnostic check on it and it said everything was okay. He said to run a cup of white vinegar through it and I did. It didnt help. Still lots of suds being produced when I run a cycle with NO dishes and NO soap!!! He said the food grinder doesnt actually grind or dispose of small particles of food, just grease!! What?!!!! We had to PAY $92 for the service call even though it is still under warranty just because the repairman and the Maytag guy on the phone couldnt figure out why this dishwasher is a hunk of junk!!!! Also, the top rack has clips on the side to lower and raise the rack. The outer sides of the top rack will only hold smaller glasses because these clips get in the way. I hate this dishwasher so much!!! My 18 year old Kenmore ran like a charm until Hurricane Harvey flooded our house. I will never buy a Maytag appliance again!!!

Maytag gas range 5 burners. Maytag is quality. Period. I doubt that other brands are made as well. From the handle of the oven door to the ease of cleaning the burners, you wont find better for the price. I look for quality and reliability. I read reviews. A deal breaker on any major purchased would be too many bad reviews and shoddy materials or construction. This range has 3 regular burners, one large burner and one small burner. The oven shelves easily adjust from one level to another. The controls are easy to reach and the timer and bake controls are easy to operate.

Fridge model # MSF25D2EAB00. I have had the fridge 3 years and 2/3 shelves have crumbled to pieces, the compressor has gone, the ice bucket crumbled, the ice maker stopped working, once ice maker was fixed it got stuck on crush, and now I am trying to order another shelf because it has also crumbled like the rest and this is in a household of 1 person! I am just getting the run around... I have been redirected to 3 different numbers now (800-344-1274, 866-368-6478, and 877-468-2371) and now I had a rude customer service rep so I asked if I could speak with someone else and I am now on eternal rot on hold. Pretty sure he didnt even transfer me and Im just sitting on hold on his line while he is laughing. Time to hang up and try again another day. #un**believableI was also told that if I purchased the extended warranty plan that it would cover the crappy shelves in the future so I did and now they are telling me it doesnt cover them and it only gives me a discount on them. MAYTAG YOU OWE ME A NEW FRIDGE... THIS ONE IS A LEMON! I have no clue what my order number is or where my receipt is at the moment but I could get a copy Im sure because I purchased it on my HomeDepot credit card so if you want it let me know and I will provide it to you then.

Purchased this Whirlpool made Maytag Stainless Steel dishwasher Feb 2013. By Jan 2017 the washer was no longer operational. Due to poor factory design the touch pad wiring harness was crushed during the initial assembly. The harness is routed behind the touch pad/pull handle faceplate in the door. The factory design provided no clearance for the harness. Obviously after little use (opening and closing of the door) the pinched portion of the harness behind the pull handle becomes compromised causing the ELECTRICAL SHORT.I phoned Whirlpool the maker of the Maytag Stainless Steel Dishwasher for assistance, all they offered was a repair plan in excess of $300.00. I purchased this supposedly quality American Made Whirlpool product as well as a range, microwave, washer and dryer in the spirit of supporting US labor. Now Im stuck with a dishwasher that has an ELECTRICAL SHORT, possibly a FIRE HAZARD and Whirlpool trying to milk me for more money. Please think twice before purchasing anything from this Michigan based company.

I have had my Maytag Bravo for 5 years now. I originally paid 1800.00 for the set. And yes that is without the tax. Well I also got a warranty. Three years after I purchased my set my dryer stopped drying my clothes. I called the warranty company for a repair man and lo and behold my warranty is over. The repairman came and said that my lint was backed up. He stated that it was a good thing that I called when I did because they have been known to catch on fire. I asked him how is this possible? I check my lint screen and clean it after every load. He stated that the lint falls off the screen and just settles at the bottom of the dryer. And sometimes the dryer will get so hot that it will actually set the lint on fire. He fixed it but now it is back to doing the same thing two short years later. Im thinking that Maytag must know about this now and I am wondering why they havent did a recall on these before someone gets hurt or even worse by trying to do laundry.

I bought this Maytag MCT washer and dryer set brand new from Lowes October 31st, 2016. When I washed the first load it made so much noise I thought it was broken. Called Lowes and they said it is just noisier than the older ones. This is the water/load sensing model, supposed to be great. I am usually here by myself, so at most I wash one load of clothes a week. I have a queen size mattress pad in there washing right now. This pad fills up the drum pretty much, I have it on deep water but that only gives me maybe 1/4 of the drum that has water in it. The pad is wet from wicking, NOT from the water covering it. How is this supposed to clean anything when the water is not covering the items?When it spins out, it gets off balance easily. The manual says to not worry about balancing load as you put it in there, but doesnt make any sense to just cram on one side as the water isnt going to float the cloth around to balance. The settings for Bulky does nothing more than the setting for Deep Water, you still do not get enough water to wash your clothes.It also does not do any good to add fabric softener to the machine, as it seems to just take it all out, you cannot smell any fabric softener on your laundry when you are transferring it to the dryer. And the laundry when dry isnt soft like it was with the old machines. I will be 62 in December 2017. My parents always had Maytags, never a problem. This is the 4th set of Maytags I have had. And bought a set for my daughter in 2013 also. And this by far is the worst. Their quality is completely gone now. Nothing but cheap made products that are predestined to fail. Friend across the street said she had looked at this set when she was in market to get a new set. She has an friend who works on appliances and who works for stores selling these models and he told her, they were not worth buying. Wish I had known that. Do not waste your money.

Bought a Maytag top loader washer from Lowes in July 2017. Have had nothing but problems due to faulty computerized guts. Worked intermittently and took a long time to wash compared to older machine. Repairman out twice... replaced computer board and still have problems. The machine was made in Canada according to the label. Hey Canada, what is going on making junk? Too bad that we did not know beforehand what junk the Maytag brand has become. Lowes should not sell this junk to help its reputation and valued customers.

I am replacing my second Maytag Bravos washing machine. My first had heavy use and I rationalized that the 5 year life span was due to the heavy use. The one that I am replacing now is only 3 years old and has only done laundry for one 67 year old woman. It suddenly needed two parts with a repair bill that was going to be over $600.00. I decided it was in my best interest to spend a couple hundred more and replace it. I will not be buy Maytag again. The appliance company that I have bought most of my appliances from recommends Speed Queen which ironically also has a full 10 year warranty on all parts and labor.

In July 2012 I purchased a Maytag BTM standard door refrigerator from Home Depot. Approx. 2 weeks from the 1 yr. Standard warranty July 2013, my refrigerator started cycling like every 20 minutes and loud popping noises started occurring. 1st service tech would only stay 15 minutes & did not want to stick around to hear the noise. Ran the standard tests and said everything was fine. That was around Aug. 2013. So I put up with it for a few more months and finally the popping noise was getting louder. 2nd service guy (Jan. 24, 2014) got to hear my video recording of the refrigerator cycling and loud popping noise. He replaced a bad dul part (Note: they all wanted to blame it on our ice maker that we never ever hooked up). Oops...wrong diagnosis. Whatever he replaced stopped the constant cycling pattern but now the popping noise is getting even louder like a shotgun going off. 3rd repair guy (Feb. 20, 2014) tells us that is normal and recycle product material is not that good nowadays?? I pay a $1000.00 for a noisy refrigerator and they say it is a normal sound. I dont think so. The refrigerator is now popping so hard that the right side of my refrigerator that faces the open is now buckling due to the compression of the heating and cooling which is causing the loud popping noise. If you rub your hand down the side of refrigerator you can feel the waves forming on the side of the refrigerator. Trying to get a Maytag rep out here. Something needs to be done about the production of these bad appliances.

So sad, purchased brand new Maytag washer and dryer, Commercial technology (MVWB766FW) labels. Looked and appeared impressive. Machines cost almost $1,000 each. Had twenty year old machines that still worked, I didn’t want to face a unexpected breakdown and decided to replace. What a mistake. I’m 67 and all my life from grandma through my mother Maytag was the best, not anymore. Once my equipment was installed I washed a load checking frequently, noticed almost no water in the huge tub and my clothes being beat by the agitator but not enough water to move the clothes. I tried to change to high water setting but had to cancel this load to do so. Once on high water setting I started the load again, water still very low and agitator just rubbing the clothes directly next to it, no movement of the clothes at all. Ran completely through the wash cycle but when moving to the dryer noticed some light blue shorts had dry spots, many, which had never been wet even through the wash, rinse, and spin cycles. Had a warranty service call and was told this is how the machines work. I told the serviceman had I known that I would have never bought the machines. He told me the salesman should have explained this to me which he did not. The only way I can wash my clothes in the new, expensive machine is on bedding cycle with high water setting on. Sad day when American companies can legally sell such crap. Also, called the company where I purchased and ask about return. To that I was told once I made the purchase they were mine and Reid’s Appliance in Santa Barbara didn’t take returns. Reid’s Appliance can’t be trusted. Buyer Beware, this stuff is junk. I will be throwing these machines out soon as they aren’t even sale-able on the used market. MAYTAG RIPPED ME OFF.

Like many people here, I have a Maytag Dishwasher Model # MDB7749SBW3 Serial # F40107007. We have had this dishwasher for about 12 months to 18 months. The first indication that there was a problem was some of the lights were acting strange. Then the dishwasher starting going nuts. I removed power from the unit thinking that maybe the controller became confused. The problem persisted. I would hit buttons and either nothing would happen or something completely different would happen.I take the dishwasher door apart and remove the touch pad. I notice some discoloration on the ribbon cable. I remove the glued on front panel to look at the electronics behind it (see pictures) and I see some discoloration there as well. So using my multimeter, I find that there is a direct short between pins 4 and 5. I vigorously flex the cable at the point of discoloration and the short goes away. So at this point, I doubt that I can get just the flexible circuit strip so Im going to have to pop for a new touch pad assembly. I didnt go further in the measurements as there was no point since I already detected one failure. Furthermore, I inspected the computer control unit and I did not see any obvious signs of corrosion or discoloration anywhere on the processor board. So it appears that there is no problem with it.Conclusion: Many people are at a disadvantage when it comes to electronic devices. In my professional opinion, this is clearly a failure of the insulating material of the ribbon cable due to environmental contamination. Visual inspection shows that corrosion of the conductors is clearly evident. About Me: I have been an electronics technician on and off for over 20 years now. I have a 2-year college degree in electronics technology and I am currently in school to become an electrical engineer. In my house, when something breaks, I fix it.

I love it. It has a big tub. It has no agitator. It uses a lot less water. Many cycles.perfect machine. I would recommend this to everyone. Also top loading. Would never get another front loader. They arent worth it.

This washer is the worst piece of junk I have ever purchased. From day 1 it never cleaned my clothing. It was too much money to call a repairman so I have lived with it since October 13, 2013 and I have finally been able to buy a new washer this week. My husband would come home from work and ask me why I put dirty clothing in his drawers, he said his clothes stunk and were stained. This washer just did not clean the clothing. It didnt use water. I cannot say how many times I would open it after washing a load and the clothes were dry. It saved water alright, it didnt use any and it was installed properly. If you are going to purchase a Maytag Centennial, run. Dont walk. Run, fly, look the other way, just dont buy this HUNK OF JUNK! I cant even sell it, so we will sell it on eBay for parts just to recoup some of our hard earned money! MAYTAG YOU SHOULD BE ASHAMED OF YOURSELF!

Purchased new washer mid-February from Maytag dealer. He said machine has few problems and it was a good machine. 3 and one half months later, the machine is dead. No lights on display but power at plug. Repairman comes at appointed time and says it needs a new circuit board. Within a week, the part arrives and an appointment is made to install the new board and still have the same problem. Have to order a new console panel. 3 and a half weeks later, the part comes in. I have a job which I used the money to buy this machine and now the service advisor wants me to take off work so they can try to fix this machine. He told me I cannot return the machine. Whirlpool Canada LP Customer Assistance said they could not do anything. When I asked to talk to her boss, she put me on hold. She came back and said they would give me 6 months extended factory warranty and she would email this which I have not received. Work schedules will dictate when the next appointment will be made.

Purchased 6-1/2 years ago when we had kitchen remodeled. Bought the stainless steel with stainless interior. The interior design was perfect for placing the various dishes, glassware and utensils. There are a number of settings to choose from, however, we tend to use it as more of a sanitizer so the light or normal wash are the preferred and dont use the heat-dry as we dont find it necessary. Very pleased with the quietness of the cycles and have no regrets with our purchase.

We purchased a top of the line, state of the art Maytag washer and dryer Neptune. The fill valve failed twice, flooding the first floor and the big storage room below. Thank God we were here! Now the thing halts mid-cycle and wont continue. The repairmen both said the design is messed up and they hate to work on the Neptunes.

When I attempted to contact Maytag about an issue in my 3 month old washer all I received is an automated email back saying to contact one of the repair places on their website. There was one, so I notified Maytag I would contact them. I contacted them. They said Maytag had not notified them that this was a warranty repair and if I wanted them to come out I would have to pay for it. I have attempted to contact Maytag several times to get this straight. Guess they are trying to wait out the warranty to respond. Will NOT EVER buy another Maytag. Too bad they used to be a good product.

Bought a Maytag Bravos XL washing machine because I thought it was a dependable brand. We have had it 14 months and the lid (upper left corner) will not stay connected. I called Maytag and the rep states to me Is it broken in the upper left corner and I replied yes. He continued he is just the parts guy, but every bravos has the same problem. I asked for the replacement part ($302), but he said the part is on back order for 60 days. He continued that maybe I should buy two because it will happen again. I only paid $700 for the washer, but it should never break down after 14 months. I highly recommend a different brand.

I have a Maytag washer and dryer. The washer is a top loader with a metal drum. You can hardly hear the washer while it is running, and I have had no problems whatsoever in the past six years of ownership.

I purchased my Bravo Maytag washer, dryer set May 31, 2015. I spent a little extra because they were suppose to be so reliable and last for MANY years. What a HUGE mistake! The washing machine is rusting. (A friend said, although Maytag’s big promotion was Made in America the inferior metal probably came from China). Buy cheap and to “hell” with the consumer! As many horrible reviews as I have read about the Bravo Series of washers and dryers I am shock there has not been a recall or better yet, a class action lawsuit! Rusting washing machine and have had to replace a part on my dryer...of course all cost came out of my pocket. I will NEVER buy anything Maytag as long as I live. I have told and will continue to tell my friends and family my nightmare Maytag story!!!

Bought used and still performs like a champ. It's old. Have the matching dryer but that quit working some time ago so I hang dry clothes.

A washer should last 10 years. Bought it in 2009 - after two years we spent $200+ on seal and bearings. Now, in 2014 we need more seal and bearings and the service tech recommended by Maytag says the cost will be $500+. Machine has a serious design flaw, and bad parts, and bad service.

The machine can clean even king size quilts, and clothes come out very clean. It is a front load and there are no problems with odors. There are many cycles to choose from. Cycles spin gently enough while getting out most of the moisture.

Washer needs new transmission at only 3 years old! Maytags 10 year part replacement doesnt cover it. The company actually asked why I didnt purchase extended warranty, I thought I didnt need one. Bad bearings, it doesnt wash the clothes clean, $400 to fix it. Needless to say Im buying a new washer and it will not be a Maytag, worthless piece of scrap!

This is a portable dishwasher. It does a great job washing the dishes. It’s fairly quiet and gets them very clean. It moves quite easily. The silverware tray is generous. The cycle takes a bit of time, but I don’t think it is excessive compared to other brands.

We purchased this Maytag Centennial washer in 2009 (model # mvwc6esw/Wd; type 849-05; ser # cy1741855) and I have hated it ever since. I had an old 406 Maytag washer that was worth its weight in gold - repaired it as long as possible. I bought this new one because it was a Maytag and that was a mistake. The way it agitates my clothes get tangled and they never did that in the other original Maytag. We had to have it fixed not long after we got it and now every time I turn it on, it immediately starts to agitate on every cycle except hand wash, which it never did before. If I knew it agitated the way it did, I never would have got it. Good thing we bought an extended warranty for this machine. We have used it once already and it looks like we may have to use it again. I am very disappointed in this machine and your workmanship. The old machines were much better and more dependable.

I saved for this refrigerator for some time and assumed at my age this would be my last one. Thats a joke, less than 2 years and I see this water leaking on my floor. I blamed my dog at first. This was a Home Depot purchase. I love the middle drawer but the freezer has this problem. I removed the ice but it comes back. I did not purchase the extended warranty because if you have an excellent product, you dont need an extended warranty. And of course this happened RIGHT AFTER the warranty ran out. I am VERY upset with Maytag/Whirlpool. Will NEVER buy another product from them. This fridge should not have problems in less than 2 years.

This is the WORST washing machine I have ever had. You cannot control how much water goes into the machine and the clothes being washed are not even covered by water. They stick out above the water at least a few inches!!! How can anything get clean if no water is touching it! I even add water into the machine at the beginning with jugs of water just to cover the clothes... the machine automatically gets rid of that extra water and when the wash cycle comes on again the clothes are not submerged! I paid A LOT of money for this awful machine and Maytag needs to do something about it! And, yes there is a sticky gummy substance on all the dark clothes! I even put clothes in the washer with a dirt spot on it purposely and the spot is always there when the wash is done. Nothing gets clean! DO NOT BUY this machine... you will be very sorry!!!

I purchased the washer 12 months ago. I liked large tub size and Maytag name. Thought I had made a good purchase. Boy am I am sorry. The washer overflows my large utility sink for drainage on large load setting and clean setting, ruining the flooring in an adjoining room. You cant wash black clothes in it leave white residue spots all over clothing. You cant use pod soap. Doesnt dissolve totally. Just on your clothing so you must wash again. So now I am trying to figure out what I can do but afraid I am going to replace it. Would Not recommend this product. Bravos XL MCT MVWB835DW1.

I bought a Maytag washer 3 years ago. Maytag gave me a number for one of their warranty service repair shops in my area. The first repair service doesnt even respond to my calls. The second repair service is a total ripoff. So in summary, Im stuck with a 3 year old washer that has a broken drive assembly that the warranty wont cover.

Purchased this Maytag microwave brand new on April 2017. In January 2019 began to have issues with the display reading open/close door. Maytag would send a repairman for $160 to take a look at the problem. Parts of course are extra. I will never buy a Maytag product again.

I bought the larger capacity machines to save time because Im so busy with my family and wanted to cut down on loads. I was surprised to find the capacity can really only operate at half, which is as large as my old, smaller machines. The washer is extremely sensitive, meaning it may take four or five tries (this morning was four) to arrange the clothes - even a small load of delicates - in it in the exact way the machine wants before it will allow the cycle to start. This is exceptionally frustrating, particularly during the busy morning or when you are tired at night. So you have to stand there and wait until the sensing function is happy and you see the water pouring in. Yet often you will return to the machine and it will have an error message that occurs inexplicably during the spin cycle, so the wash cycle will need to be restarted. It cannot just be continued. The machine is not only a huge time waster but a water/detergent waster as well.I learned that the sensing function on the dryer is useless as well after coming back to many loads of damp clothes that sat there, got little funny smelling as a result, and had to be rewashed in the nightmare washer lol. So now I just use the timer function. It takes about two hours to dry a regular load of towels, so be prepared for that. I bought Maytag because it is an American-made product, but I wont make the same mistake next time. If the quality is any reflection of the functionality, it probably wont last very long anyway. Heres to hoping.

I purchased a Maytag Dishwasher Model MDB7749SBM3 in January of 2014. I have had issues with the control board for the past month: lights come up at random; it takes 3 to 10 trials to get it to start and now it is dead. After reading many reviews on this site, I now understand what the problem is. I called Maytag customer service and they wanted to schedule a service call at $98 just for the diagnostic. I asked the Maytag associate whether the control panel issue was a common problem and she said she would research that but did not give me an answer. I am totally disgusted by this company!!! I would be happy to join a class action suit.

Have had this problem since week 2 of ownership. Even on the lowest setting, food in the fridge section is freezing and Im having to throw out fresh produce weekly. Called Whirlpool service since under warranty. The very nice service man replaced the thermostat. Only a little bit better as the temps do not range quite as extreme - only 25-46 now! I am now waiting once more for a service appointment, at least 10 days. Plus in Massachusetts they will only give you a 8-5 service window. They give a robocall the night before and you are given a 8-12 or a 1-4 time for your appointment. I also have had trouble with the meat drawer falling out of the track because the upper shelf bows with the weight of a normal amount of stuff. Now the bracket has cracked and the meat drawer no longer stays on the track when it pulled out partially (such as when you need to reach in and get something). Same thing happens with the lower drawer on the right side although the bracket hasnt cracked.

I, too, am having major problems with my Maytag Neptune washer, much like many of the writers are. I am extremely disappointed in the Maytag corporation for putting out such an inferior product that it wont stand by. I wonder if a new class action suit could be filed.

Purchased a Maytag dishwasher (Model #MDB7749SAW1) in January of 2013, installed in February. A little over a year later the control panel went out. I called Maytag and they were kind enough to pay for the part and I had to pay for the service. Now it is July of 2015 and the control panel is going out again. I called Maytag directly and talked with a service representative and the best they could do for me was for $269.95 they would have it fixed and I would have a one year warranty as well. Based on the pattern the warranty is not going to help as it goes out just after a year. For only having it 2 1/2 years it is becoming a very expensive dishwasher. There should be a recall on this control panel. Very disappointed.

This washer has a fault with certain types of blankets. Parts of these blankets come out shredded. We end up replacing these blankets. Other than this problem, the washer has worked fine.

I have always been an advocate for Maytag Appliances. Never bought anything beside Maytag. Our old Maytag refrigerator broke. Would cost too much to fix. So, we decided to buy new. We had the old white, which I was perfectly fine in buying again, however, white was super expensive. So, the salesperson persuaded us to purchase stainless steel. We got a pkg for close to $4000 all in June of 2016. Needless to say, these items have been called for repair within the 1 year warranty over half a dozen times, and have had to replace pieces that have just broken. My worst experience is the stove. I really do not like it at all. I feel the product is misleading. We wanted a self cleaning oven. It is the newest brand out there for what I consider a joke. It is the AquaLift Technology that does not clean anything. My old Maytag self cleaning oven cleaned far better than this. The same spots are in the oven. It just is worthless. I have addressed my frustration with Maytag where I was told that the oven is for the light user. Well, then you need to educate the people who sell your stuff, because I have a family I cook a lot. If this product was made for an apartment single person who does not cook then we should have been informed. Your product states Self Cleaning. Its not self cleaning!!! My frustration went up to the main office of Maytag where their resolution was to give me a discount on a new stove.What do I do with the one I have, and I was told I could sell it!!!! Really Maytag wow from a consumer that has always been a valued customer this is the level of service I get. I ended up purchasing an extended warranty on all Maytag products, because of my fear of something just breaking again. My advice to all is either buy a no named brand or buy something cheaper. Please folks if you have a family do not purchase these products. Its for people that just need a pretty display of appliances!!!

Very poor quality. Vegetables freeze at the back of the fridge I have tried everything. The vegetable drawer constantly comes off its track and the freezer door slide jams and stops the door from closing. It leaves about 1/2 inch gap. Now the Whirlpool/Maytag company changed their corporate policy and wont allow an appliance store that to come out and fix the fridge I have to go back to the manufacturer. Their website wouldnt take my email address when I tried to sign up for an account and they wont answer the phone. What a hassle. Ill buy another brand next time but never GE or Whirlpool again!

Leaking water and puddles in front (each side) of refrigerator. Purchased from Home Depot on 12-20-2011... After doing a search on the internet I found that this is a common problem with the Maytag refrigerator. This model is a two door with ice maker on left door and freezer on bottom of unit. Looks like Maytag does not want to be bothered with my problem. Model #MF12569YEW. It certainly was not an inexpensive model. Whatever happened to the Maytag repairman who was never needed because the Maytag products were so great???Updated on 03/21/2015This is not the first time this Maytag product had problems. Expensive piece of junk in my book! First, as many consumers have experienced there was water leaking in front of the refrigerator onto our hardwood floor. Now the door gasket seal ripped on the end tabs. What happened to Maytag?

I bought this washer about 6 months ago and I seem to get clothes that just arent clean and have marks on my dress pants and my whites are awfully dingy. Never have I ever had white things that didnt stay white. I honestly would never buy this type of washer again. I am actually hoping that there is a way to at least change the water level. Also I hate the fact that I cant add bleach to the water before the clothes and to let the bin fill and mix correctly. I dont think the bleach even gets to the clothes.

I purchased the gas stove in June of 2012 from Home Depot, along with a Maytag microwave (Model MGR7662WB4). Home Depot installed both items. After trying to reach into the microwave about the stove, the knob would turn itself on with me brushing up against it. This happened several times, and one time the flame shot up and I almost got burned. The last time it happened, I did not realize that the knob was turned very slightly and gas was coming out of the burner for several hours. If it were not for a friend stopping over, I would not have considered the odor being from the stove. I assumed that the drains were probably backed up and started to add cleaners to the toilet bowls. I had to open the windows for several hours to get the smell out. So I called customer service 2 times. The first person said I would have to pay for the call if the problem was not Maytag and I said, “Forget it.” Then I went into Home Depot and the salesperson in there gave me another number to call for service. They came last Friday and said that he had seen at least 10-15 calls about this and since the unit was working as designed and no recalls, there was nothing they could do. “Just wait and see if a recall would be put into place and I would be on the list to fix it. In the meantime just keep the knobs off (which I was doing already out of fear).” My sister just bought a Whirlpool gas range this summer as well and asked if I could try her knob and it worked perfectly. Again I called CS and was told they could not send me those at no charge and that it would cancel out the warranty. So I asked her what I have to do before I or someone else gets injured and she said that until there was a recall, there was nothing they could do. I told her I was going to contact Consumer Report as well as Pam Zekman on Channel 2 news in Chicago. End of story; I still have the problem and no knobs on the new stove. Anything you can do to help please contact me, and thank you in advance.

This washer has no agitator post and doesnt seem to clean as well as ones with agitator posts. I have heard that they are easier on your clothes though. The dryer works well enough, but I believe the control panel/motherboard needs replacing. The signal sounds even with the dryer turned off, which is startling to my dog and me. I reset it by flipping off the 220 breaker in the garage and leaving it off until the next time I do laundry!

I hoped the Maytag Maxima would compare to my old Maytag Neptune and it didnt even come close. Very disappointed. Doesnt fill with enough water to even WET the towels and doesnt rinse any of the soap out of the clothes. Been using it since 12/2015. Hate the Maxima. I looked for the brand (Maytag Neptune) which I couldnt find. Settled on the Maytag Maxima which is a complete bust. The Maxima doesnt fill with enough water so Ive had to add water to both the wash and rinse cycles. It has also become very noisy. The repairman has already stated that there is nothing he can do about the lack of water since the amount of water is set in the factory and cannot be changed. The Maytag Maxima is a complete bust for me! Its a front-loader that has me adding water (at least 2 gallons) to every load no matter how small. Wish Id bought a GE top-loader that Ive seen advertised.

I bought a Maytag Bravos Quiet Series 300 washer just over two years ago from Home Depot. The control board and sensor went out last week. The service technician seemed rather surprised that a newer machine would have that kind of non-wear-and-tear problem and suggested that I contact Maytag/Whirlpool to see if they could help offset the parts costs, as the repair was going to cost over $600! The customer service agent I spoke with said that there was nothing they could do because the item did not have an extended warranty. I explained to her that we purchased this unit, even though it was out of our price range, because we were told that it would last a lifetime. I would have been happy if it would have just lasted 5 years! She was very detached and it was clear that Maytag/Whirlpool was not going to stand behind their product. I will now take the repair money and go buy a new washer. You can be sure that it absolutely will not have the Maytag/Whirlpool brand!

My microwave started acting up, after about 5 months. It would not cook a complete cycle, without an error saying that the door is open, and needs to be closed. The repairman has been out 5 times already, and the problem is still not corrected. Maytag/Whirlpool has said they will not replace item, then they decided they would possibly replace at a pro-rated amount. So, I have to purchase a microwave twice, to have one that works? Somehow, I feel Im being taken for a ride in this deal.

This Maytag bravo washing machine is the worst ever machine I have owned. I bought it new, and shortly after the 1 year warranty expired, I started having problems with it. I had a repairman come out. All he did was take out the trouble shooting guide, press a code, and wait. The machine told him that each function worked. Even though it did not work properly. He hid the trouble shooting guide inside the machine, so I cannot get to it. Now I have so many problems with this machine, that it takes me all day to do 1 load. This thing makes noises that I have never heard from a washing machine in my life. I would never buy another Maytag product, nor do I recommend anyone else to buy one.

Theres always a problem with this thing. It doesnt clean the clothes, its always off balance, and now it leaks from the bottom side of the machine in the clean washer cycle. Its only 2 1/2 years old. Should of listened to the guy who fixed my old machine. Dont get a Maytag!

We purchased our home five years ago. We bought a new Maytag oven and fridge/freezer. Within one year, the oven control went out. Then a few months later, the heating element went out. Within two years, our fridge/freezer went out. I purchased Maytag products because of the commercial where the Maytag repairman is doing nothing. I will never purchase a Maytag product again.

Purchased a new Maytag dishwasher three years ago. After having it for one year the panel box no longer worked. Had to pay $300.00 to repair. Now half way through washing the dishes again no water will go into the machine. Only the first part of the cycle. I am sure it is going to be the panel box after reading other peoples problems with this machine. I will not pay to have it fixed this time. I will have to buy a new dishwasher. I will never purchase a Maytag product ever again. I have lived in my home for 40 years and never had a problem with any appliances. This would have been my third dishwasher in 40 years and as you can see it has not even lasted 4 years. I will inform my friends to stay away from Maytag.

I purchased my first Maytag dishwasher and it was recalled as being a fire hazard. I was offered to have it repaired or pay for an upgrade (approximately $200). I chose to pay and upgrade because I dont want a fire hazard in my home. After my paid replacement, I received a recall on the new dishwasher regarding the same issue (different model) and I chose once again to pay and upgrade (thinking that if I spent $700, I wouldnt have a problem). In less than two months of installation, the dishwasher died in the middle of a cycle. Filled with water, I bailed it out and called Maytag. I told them that I wanted a new one and they told me that I was past the replacement period. They sent a service man out and he stated that it was a problem with model # MDB7709AWB2 and serial # F03002958. He said that it was easy to fix and said he had done it several times. So now, within less than 1 month before my warranty is expired, the dishwasher did the same thing--it died in the middle of the cycle and wont turn on. I called Maytag and they told me that they would send out a third party repair company (JD Appliance) but I would have to wait for four days. I contacted Maytag and said that I was concerned about the dishwasher breaking down again for the same problem (bi metal unit blew). This is the second time it happened. Jeremy, the repair man, said that the first replacement was not installed properly and they should have replaced the entire unit. He stated that it was a common problem with that model, as did the first repairman in Dec 2010. When I spoke to a supervisor named Kia at 800-344-1274, she stated that they had no known issues with this model. I said that it was not what the repairman told me as well as the Maytag dispatcher. They both said that the heat sensor (Bi Metal Thermal Unit Part No. W10258275) goes up and has to be replaced because it is overly sensitive. If you are out of warranty, it costs around $200 to have it fixed. I told Kia and she said that it was not documented in her file, therefore, it never happened. I want to know my consumer rights to address this issue. I have paid for (on 3 occasions) a new dishwasher and have continuous issues that cost me money. I want an assurance like an extended warranty, free of charge, for the dishwasher that has already been repaired twice for the same exact problem. I have the original part that was improperly replaced to prove that it wasnt replaced to specifications, therefore, blowing it again. I was told by Kia that Maytag does not compensate or replace their products unless deemed not repairable by the technician. It doesnt matter how many time the same problem occurs. I would appreciate your attention to this matter.

I purchased a Maytag Bravos XL washer mid November 2013. Less than six weeks later it leaked water. The repair person has been to repair it four times. The last visit was yesterday. It now has more problems than it originally had. It still leaked water. Maytag does not stand by what they sell. All they say is they will repair it. My caution to anyone reading this is never buy a Maytag appliance. I hope this review helps someone in their decision making process.

I wish we would have never bought this brand and model. Within a month there was a loud banging and the serviceman came out and changed a valve out but it just got a little quieter but never went away. 2nd issue is cloths ball up when your doing bedding. Not sure if they are really clean or not. 3rd when we take the cloths out of the washer we are still seeing soap spots where they were not rinsed very well. We are using the right soap Gain but we cannot wash cloths in the bedding setting. We have to use the extra rinse setting to get all the soap out which defeats the whole savings issue of this machine. It says when you do your monthly machine cleaning it resets the water level but there never seems to be enough water in the tub. Also if your doing sheets in the washer and when the spin cycle starts you have to hold your breath to see if its going to get out of balance which it does 50% of the time so you stop and move things around. Also we cannot put a whole lot of cloths into this big drum because they dont wash correctly. Worst purchase we ever made. With all the negative reviews you would think that Maytag would come out with some fixes but I dont think they really care anymore.

If I could give less than one star I would. I purchased a Maytag range in September 2021, 33 days later the oven went out!! I have been fighting trying to get it repaired for months!!! The parts are not in, the parts have been shipped, oops we forgot to ship the parts, the technician is on vacation. You name it, I have heard it. After the phone call today, it looks like I will still be without a range at Christmas!! This is totally unacceptable. I purchased a Maytag because I assumed it was a good brand! Do yourself a favor... Never buy a Maytag or Whirlpool Appliance. Its not worth it. For the range to only work for 32 days is just plain Wrong....

I own an iron in case a guest needs to use it but I seriously havent ironed in over 20 years. I moved into a home in November and the appliances stayed with the home. I am systematically destroying my clothes that I always washed and dried but NEVER IRONED. They come out of the Maytag washer already wrinkled. I try to unwrinkle them in the dryer. I took 2 items to the dry cleaners to see if they could steam them but no results yet. What gives Maytag???

I bought my Bravos x washer and dryer set three years ago. Ive never been happy with them. You have to put the washer setting on bulky to even wash a normal sized load and they still dont come clean. Only three years old and Ive had problem after problem with the washer. As Im typing this I have a full load of clothes in the washer that will not wash, its full of water and wont even drain and spin. PLUS the lid wont unlock. So aggravated.

Well bought this washer a little over 1.5 years ago in 2017. The display started going haywire, flashing, going on and off and would only go to the normal setting, most of the time. Called Maytag and had service come out and Maytag would cover parts and labor. Turned out the control panel went bad. About a week later found out today part was still back ordered and not available with no ETA. So was told Maytag would replace the unit. So until I find out whether or not they will actually replace it, Im giving one star. Been holding for customer service for over 35 minutes now to verify what I was told. Its a shame because this washer was given a good review. It is a front loader.

MDBH979SAM0 - Bought this dishwasher from Home Depot 2 years ago and have taken care of it, never abused it or anything. All of a sudden it just starts freaking out, once you start a cycle it will wash and then rewash and then keep going costing us money on electricity, water and wear and tear on the machine. Ive tried everything but it seems like its just stuck in start mode. The indicator lights on the panel flip out too, they will all blink randomly. So when I close the dishwasher and dont intend to start any cycles and it is off it will start up all on its own so Ive had to unplug it. Funny how I called to order a control panel part and its on back order... Very interesting how they are out of this part probably because everyones ordering it.

This Maytag refrigerator is very nice.. Sleek black with double doors and ice two ways and filtered water on the door which is very convenient. The filters are expensive but they last up to six months so that part isn’t too bad.

Once again I purchased a maytag appliance. I was hesitant because of poor past experience. I bought a refrigerator, lasted 3 years, and a stove, a little better 4 years. When I went to buy a dishwasher at home depot, they assured me that maytag had improved their standards and now were more conscious of maintaining the quality of their products. Long story short, I bought the dishwasher in april of 2015 and now in october of 2015 the control panel is shut. I have requested a repair, but find this unacceptable as the life of appliances seems short at best. I am fearful this could be on going as I now am reading the customer reviews, and 90% of them have had this trouble more than once.

We bought the Maytag Bravos washer & dryer combo from box store. I wanted an extra large capacity washer to accommodate king sized bedding, and having fewer wash loads in general. Cons: 1 - This machine is not energy efficient when each wash load takes 1:30 to 1:50 each load. 2 - The detergent/fabric softener/oxi dispensers are a joke. Water dumps into every compartment at once. And if there’s still detergent left by the rinse cycle, well you get the picture.3 - The “Bedding” setting is the only one which will provide enough water in the tub to get anything wet. Since there isn’t any type of agitator the clothing/bedding just floats on the surface in dirty perfumed water. 4 - With any of the other settings the water level is so low it doesn’t always get everything wet so items are not being washed properly. At most maybe 2 pairs of jeans or just a few t-shirts can be washed on the “Normal” or “Power Wash” settings. 5 - Because there isn’t an agitator, clothing gets knotted up. Dress shirts, dress pants, jeans, towels, you name it, everything comes out of the washer in a knotted mess.The Bravos XL Dryer: My only complaint with the dryer is that it allows a good amount of lint to pass through into the machine. Then it’s difficult to get any type of lint brush into the vent area to remove the lint. Dampened lint in the machine can make clothing smell musty and nasty. I had to call a service to remove lint from the dryer & ducting because of the odor lingering from the inside the dryer.

I have had this Maytag washer maybe 2yrs at most and it is junk. I am a single mom who desperately needs my washing machine. My kids clothes get soiled, they ARE kids so I wanted a deep water fill option when looking for our newest washing machine. Well when I start a load of laundry, I can hear the water running and draining as it is filling the basin. So for 1 they get wet but not washed. Then when it gets to the rinse cycle it stops so the only option is to manually switch it over to drain and spin in order to not have sopping wet clothes, however, since the water doesnt fill, they arent being washed, the rinse cycle doesnt work so the soap is left in the clothes, then I just have to drain and spin in order to get access water out so they will dry in the dryer. Its very upsetting, I have no way to buy another washer, I assumed this costly purchase would last me a while.Sadly, I have seen many negative reviews re: their product. I didnt check reviews before purchasing, I knew I needed a large basin and wanted the deep fill option. I always thought maytag was a good brand. Now I am in a jam. :( If you are looking for a new washer read the Maytag reviews before considering this brand. Live and learn. :(

I had a 1 1/2 yr old front load washer. I was worried the filter might have a lot of dog hair in it so I called to just have it looked out. I couldnt remember if I had an extended warranty. Thought it would be listed with Maytag. They said no. I said OK. They recommended A+ to come out and said it would be $60.00. That was OK because I wanted to prevent any problems with the washer in the future. I thought them checking it would be a preventative measure. The tech came out opened it up said there wasnt much hair or any other problems. Put it back together, plugged it in. There was a Big popping noise and smoke! Washer no longer worked. The man said doesnt make sense but he would fix it and not charge me for parts etc. I called Maytag. They refused to do anything since it was out of warranty even though they recommended this company and there was absolutely nothing wrong with it in the beginning.After about 2 months he still couldnt fix it. About this time I found papers for a warranty with the Home Depot. The repairman said he works with Home Depot as well. Told me to contact them but I needed to pay $120.00 to him and file a claim and then he would fix it. Apparently he does not do service work for Home Depot. They sent out other repairmen. They tried to fix it but apparently it was deemed unserviceable he blew the mother board. Home Depot said they would replace or reimburse me the amount I paid for washer. Then a machine called said they were sending me a check. We will probably never buy another Maytag! Even though I want to buy American if they wont help or stand behind their products. I now have an LG we bought from Pacific Sales with a cheaper warranty and much better customer service.

I bought a Maytag Bravos washer and dryer two years ago. A week after the one year warranty was up, my dryer broke. That was in October. It took me until February to get it fixed, but within two months it broke again. It has taken me until now to get it fixed again and they found the same problem; the thermal fuse blew. Both times it has cost me over $100 to get fixed, but I still cant use every part of the top panel; I can only use timed dry cycle. I’m expecting the dryer to go again. The repair man had to re-glue the seal that went around the drum. The vents were all clean and were blowing fine, so we’re not sure why this keeps happening. Our family have always owned Maytags and they have always lasted for 20+ years. I am so disappointed with Maytag at this point and will never buy another again. Go back to the old days, Maytag! By the way, has anyone noticed they dont run the Maytag commercials anymore, because I have!

I purchased a Bravo washer and dryer set about a 2 1/2 years ago and had problems from the start. The dryer control panel went out the first day. No problem, they replace the panel. The washer is a different story. The agitator went out next and the wait time to repair it - 3 WEEKS. The agitator went out again for the second time and the tech stated that it had to be replace. Wait for it. Waiting time - 1 month including parts. To make this story short the agitator will go out every 4 months and the tech stated once its been replace it will work like a new washer. Wait for it. The agitator has been going out ever since and the wait time average 3 WEEKS. Wait for it. This Maytag is trash.

We bought our Maytag Bravos washer and dryer 3 years ago. We bought the set from E-Z RENTALS in Crossville, TN. We paid on the set for 2 years. You can only imagine how much we paid. Two weeks after the payoff, the washing machine started acting up. We were led to believe that the set had a 10-year warranty on them. They made sure that we saw the 8-10 sticker on the front of the machine. E-Z Rentals said that we had to pay extra for the warranty. They hung us out to dry. I could have bought a nice car for what we paid for this washing machine. Now its torn up again. This will make the 3rd time that we have had to call a repairman. We are ready to take the washing machine to the dump and buy a Whirlpool. The man at E-Z Rentals said that on average, the Bravos machine lasts for 3 to 4 years. After that, its cheaper to buy a new one. Does anyone know if, in fact, these machines come with any type of warranty? We truly do not have a clue. We would be grateful for any information on the washing machine. This has been a hurtful experience. I feel that we were taken advantage of.

Maytag Bravos XL: I purchased mine Nov. 9 2017. I so wish I had never bought this machine! It leaves soap residue and dog hair on my clothes and bedding. I have to wash everything 2-4 times. It’s beyond disappointing. My husband and I agree our clothes looked better dirty, BEFORE we “washed” them in this machine.