Absolutely the worst washer I have ever had. I have read some of the other reviews, wish I was smarter and checked this out before spending my hard earned money to buy this washer. My washer also is rusting at the top where the bleach goes. I never close the lid when not in use my basement is dry AND I never use bleach??? My clothes come out they are a tangled up mess. When I go to hang them they are partly dry. It isnt as though I stuff the washer NEVER put more than 8 shirts in at a time yet they all come out with dry streaks like that part of the clothing never even got wet. We all know what happens when you leave a tissue in your pocket and it goes through the washer... Well not with this washer the tissue sometimes came out as dry as it went in. HORRIBLE product. I want the old agitator/I SET THE WATER LEVEL type back. It takes forever to get laundry done. They should take these OFF the market and give us poor consumers some cash back.

I purchased a topload washer two years ago and the plastic lid has been replaced 4 times because it cracks at the hinges. It is obviously a manufacturers defect that Maytag refuses to admit. They come up with excuses blaming the consumer instead of their bad design.

My Maytag dishwasher control panel stopped working. The control panel failed, it was replaced. The replaced control panel failed. The control panel failed again and needs a fourth (4th) control panel. I have had to pay for service calls and control panels. I only use it 1 to 2 times per week. This is obviouly a lemon. I would like it fixed and to be reimbursed for the lemon part and service calls.

Had some extra time, so I thought Id add my .02 to those including myself disgusted with Maytag products! 1st up, the Maytag washer and dryer I purchased from my nephew after his divorce. The washer shot craps 2 months after I bought it from him (out of warranty of course!). The transmission went out - cost to repair $550.00. My nephew paid $350.00 new at Sears. We happened to have our ol reliable clanking GE, so we used that while deciding what to do about the washer. In the meantime, the dryer quit heating. Cost to replace heating element - 400 smackers! Dryer new at Sears was $250.00.Come to find out that even though they had Maytag names on the washer/dryer, they were cheap copies by White/Westinghouse. Well anyway we bought a set of Whirlpool Duets before doing our homework, cuz if we knew what was gonna happen... Before we knew the trouble we were going to have with the washer/dryer, we got a Maytag Quiet Series 300 dishwasher (Maytag Quiet Series 300 MDBTT60AWW). Yip, the control panel failing problem! Only purchased 1 so far (only 1?!), but my wife likes to hand wash the dishes. If we were the typical family using the dishwasher all the time, I would have replaced more than 1 at a cost of $135.00 each from Sears and doing my own R&R work, saving on the labor. Cost new at Lowes - $350.00Up next is the Maytag fridge. I purchased it back when our 2 boys were at home. I bought it mainly for the name and large capacity. After about a year (yip out of warranty) the cooling was very uneven. Sometimes the freezer would defrost by itself, then it would start working ok again. The top couple of racks in the fridge would be quite a bit warmer than the bottom. I understood the top racks would be a little warmer, but Im talking like 15 degrees. I called a repairman and told him about the problem. He said hes received numerous complaints on this particular fridge, and theres really no way to repair it unless the electronics are replaced as well as the compressor because as the compressor gets weak over time, the electronics get fouled up by this. Cost new - $1300.00. Estimate over the phone cost to repair - $950.00 with no guarantees. Replaced with a SamsungAs far as the Duets? No problems so far. They work great and we are very pleased by them. But I have did my research and am holding my breath! I also have a Maytag microwave thats still working, but has did a couple of unusual things - the lights in the front panel display started flashing showing a fault. I unplugged it when its did this to reset it. That was a while back and now it seems ok. At least for now!When someone says, Yeah, well, you might just have a lemon, but the rest of Maytags appliances are fantastic! My wife and I when we hear this are ready for a fight! Weve had experience with all of Maytags products, and with the exception of the Duets (so far), they are nothing but junk!! Another thing I wish to mention is the Samsung fridge. Its about the only model that has a factory 5-year warranty on the compressor and major components. Weve had several fridges in our married life, and the Samsung is far superior to any fridge weve owned. Ill be looking to that brand in the future. The last item I promise: If you read the reviews on front load washers, none of them get very good ratings. If I would have know that, I may have purchased a top load. But the Duet washer does do a superior job (IMO) cleaning the clothes, and the clothes are virtually dry after the last spin.

Very dissatisfied with Maytag Washer Mod MVWB835DW0. This Large Capacity machine does not adequately clean a large capacity of clothes. In order to get a half decent wash performance from this machine, fill the machine only 1/4 full. Even using the recommended manual, I was very dissatisfied with the way my clothes looked after washing them with this machine. While I have been unhappy with the performance of this machine since purchasing it. What motivated me to leave this review is when my pants had the same sand debris on them after the wash as they had before the wash. I will be looking for a new machine this weekend. IT WILL HAVE AN AGITATOR TOWER!

Maytag Bravos Quiet Series 300 - Just DONT BUY this junk. We bought the washer and dryer set from Home Depot in 2011 and have had nothing but trouble with the washer. Three times small objects like dimes, pennies and nickels got past the agitator into the drain pump which has been replaced twice. Beneath the agitator we even found a few missing socks. Today after a visit to the Laundromat, we bought a Samsung with a 5 year extended warranty. If that doesnt work it will be an old fashioned Speed Queen next. We will never buy anything Maytag again and I hope to influence everyone we meet about them. I cant wait to throw it into the city landfill for recycle dog food cans.

I bought the Washer and Dryer. All I can say about this washer is that it does not use water enough to be considered a commercial type of washer. Its balance is poor also for being so deep. I have to pour a bit of water on the clothes so the sensor thinks it’s a heavy load and do an extra rinse. And I saw that on a video regarding this washer trick. But I’m wasting more water cause I have to rearrange the clothes when done. I put the top ones on the bottom and start over. To me it’s a waste of effort sometimes I just go to the laundromat. They should consider their products if we all are complaining about this they should really do something. To me the washer is really useless.

So far, so very good. This is the first time owning/using an electric oven. I just love my Maytag. It was affordable, especially since it was a combo sale with the over-head matching microwave from Home Depot. Two years later and it's as if I just purchased it. Wonderful, wonderful, wonderful.

Stainless steel 2 door refrigerator with a bottom drawer freezer. Good space in both. Finish is almost fingerprint free. I bought 5 appliances at the same time so pricing was very good.

I absolutely do not like the fact that you can’t choose what size load you have. The washer wants to do it for you but it is not very good at it. You have to fool the washer to get any kind of water level or just use the deep fill every time which is what I do in order to get the clothes clean! This defeats the whole purpose of trying to save water. Also there are too many settings. I mean we’re just washing clothes here not flying a jet. I personally would prefer dials instead of the digital instrument panel. So much easier.

Both Sears and Maytag have lost my business FOR GOOD! We purchased a Maytag Bravo XL # MGDB980W0 2 years ago. We called within the 1 year warranty period via Sears, they sent a tech out then charged us. The dryer kept shutting off before clothes were dry. We thought the problem resolved, then reoccurred after the 1 yr period. Neither Sears or Maytag would stand behind the product citing it has been discontinued due to problems. Well... yeah, no kidding. We paid BGE energy efficiency company to come out and evaluate it. They tweaked the exhaust vent and cleaned out the duct, however, they said we needed a new sensor. My wife bought a new sensor, installed it, and the dryer still wont work right! (Shutting off prior to clothes being dry). BOTTOM LINE UP FRONT: I researched and bought a new gas LG dryer on sale at Home Depot and shelled out $849 unnecessarily thanks to shoddy product and lack of company integrity. DO NOT BUY SEARS OR MAYTAG!!!

Overall- I think washers aren’t made to last like they once were. Growing up- we had the same washing machine while living at home. It seems now- they only last 10 years if you are lucky. They should make more longer lasting machines.

Have not had either inspected, but last night the dryer started to rumble and then caught on fire... Fireman suspected bearing bad and caused a spark igniting dryer; washer has started making a shrill loud noise on the spin cycle.

We have purchased several washer/dryer sets in the past decade & will never purchase another Maytag. After 3 years of very light use, it stopped working. We had a certified Maytag repairman come & tell us we needed a $600 circuit board replaced. We reluctantly paid for it and 3 months later, intermittent problems began. Plus, it is obnoxiously loud. The repairman said this is normal. Randomly stopping the cycle, not starting the cycle at all without multiple restarts ... the list goes on. The 3 Lg sets we have bought are awesome. Maytag may have been king in the 60s, but the quality of their products has tanked. Dont waste your money on their products.

I purchased this machine 6 months ago - have called 2 repair people. Thank God I purchased at Sears with extended warranty, was just replaced. I would tell you if you are looking for a machine run away from this one. It tears clothes, have to wash everything on bulk wash or I would not get enough water to say how bad this washer is. If someone called me and said I won this washer, I would say no thank you. And if I had to say Maytag repair called them, said she not getting enough water. Now this is what they told him: thats how we designed it. Forget about big drum, you cant put blankets or any larger items, goes off balance. And I have to say, if I had the money, I would put to the road and go back to wringer type. So again, do not make my mistake. Do not buy this washer and let me say the second day I made a complaint, was told it take time to get adjusted...NOT. I give this washer a 0.

I bought a Maytag Bravos washer and dryer two years ago. A week after the one year warranty was up, my dryer broke. That was in October. It took me until February to get it fixed, but within two months it broke again. It has taken me until now to get it fixed again and they found the same problem; the thermal fuse blew. Both times it has cost me over $100 to get fixed, but I still cant use every part of the top panel; I can only use timed dry cycle. I’m expecting the dryer to go again. The repair man had to re-glue the seal that went around the drum. The vents were all clean and were blowing fine, so we’re not sure why this keeps happening. Our family have always owned Maytags and they have always lasted for 20+ years. I am so disappointed with Maytag at this point and will never buy another again. Go back to the old days, Maytag! By the way, has anyone noticed they dont run the Maytag commercials anymore, because I have!

I purchased a new Maytag fridge apx 8 months ago (model# MFF2258VEW6). It has french doors and a bottom freezer and from day 1 it has constantly leaked water all over my kitchen floor. I started putting towels in front of it after my first slip and fall. I had the water line checked for the ice maker and it was fine. It continued leaking day after day. Then I started getting a lot of ice build up all over the drawers and on my frozen food, which became freezer burned and I only had the temp at 2. They have a warranty on it, so called the company and they brought me a loaner fridge of the same kind.. OMG this fridge is doing the same exact thing, even worse. I am disabled and fell last night again and my leg and foot is so swollen.. I really hurt myself and Im not going to let this company get away with this!! I called the company and told them and they are checking into what they can do with the refrigerator. After reading all the about the Maytag bottom fridge leaks and other problems, I refuse to get the same one again. If they do not do something, I promise I will before I get hurt again!

A week after warranty expired, our 1 year old Maytag gas range (model# MGR7662WS 4) required new Direct Spark Ignitor (DSI) board. Knowing it was just beyond warranty, I inspected wiring first and found that the Bake connector on the DSI was loose, flopping around from a bad solder point on the board. Called Maytag and informed them of this manufacturers defect and all they offered was a $20 discount on a replacement part ($220 instead of $240). It worked with new part for 4 days, then something else went bad causing oven to spark, light, heat to less than 100 degrees, then shut down, then restart, then shut down, then restart, then stop doing anything. It has never worked correctly since then. How can a manufacturer of almost all domestic brands get away with such shoddy workmanship.. Taking advantage of defective or poor quality parts to sell more of the same when they fail and for an enormous markup? Where are the regulators who oversee monopolies and blatant scamming of American consumers?

I have a Maytag front load washer, and it has been flashing codes since day one, smells like mold, does not spin water out, and at first, all Maytag could say is, Im using too much soap, the wrong soap, loading too full, and I have it on a stand that is sold with the washer that they dont recommend, after I paid $300.00 for it. Now, it is flashing an E3 code, and will not finish a cycle at all. Maytag wants money to fix the problem that thousands of consumers have, after paying over $1,000 for the machine. I will never purchase another Maytag product, for as long as I live.

Well I like all the other people have the very same problem. Ruined floor from sheet of ice that forms on the bottom tray daily. I was told I need a new main board which I understand is about $500.00. I am 55 years old and this was my first brand new fridge. I am so so upset. I grew up with the whole Maytag repairman commercials where he was so lonely cause he never had any repairs to do. All my life I grew up with these commercials. I thought I was buying the best. What a disappointment. It has been in my living room for 2 years. I keep thinking something wonderful is going to happen. Now I have to pay someone to haul it off. Great.

We bought the Maytag Bravos XL washer 6 years ago when we moved into a new home. We have a large family and after reading many reviews, we settled on this washer. It has served us well for the past 6 years. At the moment, however, it is out of commission. The bearings wore out. My husband ordered new parts and we hope to have our washer up and running again in a couple of days.

Its about Maytag MDE7600AYW Atlantis electric dryer issues, Nov 2005 model. There is an obvious design flaw. I have replaced the automatic dryer control board twice since 2005. The unit simply never shuts off, or cooks your clothes for 2 hours. Who will recall this unit and fix the circuit? They will not admit their error.

French door always has freezer closing problems. Whenever the freezer is not closed tight, the bottom will form ice block, and freezer doesnt close. I have extended warranty but the repair people do not give quick appointment. I sick of this product.

Washer breaks after 2 years. I purchased a Maytag Bravos XL washer from Lowes just 2 years ago. One of the main driving factors for the purchase was the Maytag brand. The repair tech just told us the bearing was bad and we need to replace this and the drum. The service call was $100 and the repair will be over $500. I can purchase a new washer for this. I strongly recommend not buying any Maytag product. The brand used to stand for quality but not now. I dont think the Maytag repair is still the lonely tech they used to be.

High dollar front load washer, less than 2 years old, just a waste of time & energy to run it, clothes come cleaner, if you leave them out in the rain! DONT buy Maytag, I never will again!! The customer service SUCKS even more than the product, 3 hours of my life spent today e-mailing, calling, live help, NO response? They must have shut down customer support due to the overload of calls from UNHAPPY customers!! NEVER again!!

Purchased a Bravo set 5 years ago. Paid $730. For the washer. 4 repairs in 5 years. It is now has a bearing out and that will cost $450. MAYTAG used to be the best... buyer beware!

We owned Whirlpool front load prior to the Maytag set we now own. Our Whirlpool was the better one. Shorter wash cycle, better cleaning & never had a problem with the seal. Maytag dryer doesnt signal properly when laundry is dry. You have to go multiple times. I wont purchase another Maytag set. We owned a Maytag top loader set and they worked like they should have.

We have had 2 Maytag dishwashers only last less than 2 years. Since we can only have a portable because of owning an older home the expense is too much anymore. We also had a Maytag Neptune clothes washer last only 2 1/2 years. We had always respected Maytag and trusted them. That trust is gone. It is too expensive to buy and lose them after barely 1 1/2 years. We had a Kenmore that lasted 23 years. I dont know what company to trust anymore. The one we just had quit working a month ago was purchased October 3013. Maytag dishwasher Model #MCD4809PAW2 Serial #F34003436.

We have a Maytag Neptune washer and dryer. The seal is full of mold. We replaced the seal a few years ago and I wipe it and try to clean it every load, but it is useless. I saw there was a class action suit and I was never notified of this. I would have participated. I want it fixed, replacing the seal does not work.

Such a horrible and expensive kitchen purchase. The stainless looking pieces are either fake or very poor quality - they scratch so easily. After the first year of use the top of the stove looked like it was 30 years old. The oven glass is extremely hard to get at to clean - you have to remove very finicky screws that dont go back into place easily. Oven temp is questionable and it takes a very long time to heat up. I would never recommend the Maytag Gemini oven to anyone.

I love my Maytag washing machine. It have different settings for the wash, also a size load for your washing, and I love the rain cycle. You could do single runs with Downy or extra runs which is great. Especially great if you’re doing blankets and towels you need that extra rains. Great reliable machine. Highly recommended.

Ive tried all manner of washing clothes, especially dark ones. Different cycles, different detergents and amounts, but it always leaves scum marks in folded places. I have to either brush off what I can, and/or rinse the clothing in a sink and then rewash the clothing without detergent. In an attempt to save water, I end up using two or three times the amount.

I purchased the Legacy series washer and dryer from Home Depot in 2005. For the first 3 years, the washer worked fine. Since then, it has all been downhill. When I use bleach, I have to run an empty load because for whatever reason, the bleach goes through to the next load which has resulted in a number of ruined clothes. The wash cycle leaves clothes dirty and some even come out partially dry?! The rinse cycle does not always work as more times than not, the fabric softener is still in the dispenser cup. The spin cycle is getting worse with each load. Sometimes I reset the spin cycle as many as three times at which point I hand wring the clothes. This creates a strain on the dryer as I have to run it extra long to dry the clothes. I am more disappointed than I can say. I will never purchase anything Maytag again and I will not purchase from the company who makes Maytag products.

Because it is the high efficiency model, need to leave the lid open so interior will dry and not smell musty. Also, recommend using a washer cleaner such as Affresh or Tide tablet every now and then. But works great!

Unreliable! When you push start, it goes into sensing mode and starts to fill. You walk away thinking it will run to find out an hour later it is still in sensing mode! Wasting electricity, your time and talk about stress! You have a 50-50 chance it will go on and run the load, but if you dont have time to stand there and watch it. FORGET THIS WASHER. Also does not clean as the old agitator washer, which I luckily still have, yeah. Always read reviews before buying anything. Nice website.

I purchased a washer on 8/13/12. I had it installed on 8/20/12. It did not clean clothes properly. I went to Two Guys and they said they dont take returns and told me to call Maytag. I called Maytag and they sent a a service agent to check the machine on 9/10/12. They said the machine codes were imbalanced and over stud. They need to recalibrate the machine. I did laundry the same day and still find clothes do not come clean. I need to return the machine. I called Maytag and was told they dont take returns. This machine is not cleaning clothes as it should be and I want a refund!

I bought my Maytag Bravos washer and dryer set about 3.5 years ago when I moved into my home. There was a 20-year old set here that did work, but I wanted something newer and more efficient, so I donated the old set and bought these. Performance of the washer has always seemed mediocre, clothes dont get as clean as I think they should, whites are dingy, despite using hard-water additives and the correct HE products.A few months ago, the washer started a new behavior: stopping during the initial fill cycle and displaying an F1 error. I soon figured out if I hit cancel then start again, it would resume filling and proceed with the cycle. Over time, I had to repeat it more and more. Its now up to ten F1 errors both at the beginning and end of the cycle. I dont have that kind of time to babysit my washer. I already have a full-time job.I have called Maytag/Whirlpool twice now, both times getting unsatisfactory answers. Even after escalating to the customer service supervisor, I was basically told that it is most likely the control board that is the problem and since Im no longer under warranty (that washer ‘is’ almost 4 years old, maam), Id either have to order the part myself from their supplier (total cost $250 + the risk of DIY), or buy their service package for about $350 which included fixing that problem plus one additional years warranty.I pointed out that for a major household appliance that I (over) paid for, I expect a life of more than 4 years, especially since I had a working 20-year old washer when I moved in here. Since when is this acceptable? I could understand if it were a wear-and-tear part, like a rubber seal or something that moved constantly and would eventually need replaced. But this is the electronics module, something that cant (or at least, shouldnt) be worn down or broken by use or even user error. This is an integral part of the machine, and if it has a fault (which it clearly does), the manufacturer needs to stand behind it and help the consumer.What angered me even further is that the customer service manager even admitted that models similar to mine had had similar problems, and a free control board was sent to those customers. But my model was not in that range of production, so clearly they have no fault, in their eyes. Apparently, its not even remotely possible that maybe when they determined the range of models they believed to be faulty, mine hadnt been in use long enough to display the same behavior? Maybe the range they selected is too restrictive and they missed some. From the volume of complaints Ive seen online, Id bet that to be the case.I asked to be transferred to their legal department, and was refused because we just dont transfer customers to the legal department. Well, I just dont buy Maytag or Whirlpool anymore, and Im going to do my best to make sure nobody else does either. Im replacing this ** with a different brand, one Ill be sure has tremendous reviews and a manufacturer that will stand behind it.

About 6 years ago we purchased a new french door style refrigerator. It lasted one year and one month then needed over $700 in repairs. First you need to know I am into electronics, DeVry graduate with 30+ years experience in repairing electronic devices. The Maytag basically frosted over in the freezer and was warm in the upper part of the fridge. I called a friend who had experience fixing fridges and lo and behold we found something really unusual.The way this machine operates is by blowing the cold air from the freezer up into the fridge. There is a fan located in the back of the freezer wall that does this. We found the fan, which was mounted in a grey box, spinning at about 2 revolutions a minute. My friend took me to the wholesale parts distributor he uses and we gave them the brand (Maytag) model (MFD2561HES) and they gave us a fan... just a fan with two wires. No grey box with fan inside... At this point I got curious, I mean WTF?!?The grey box was made not to be opened and I had to get clever so as to not damage whatever was inside it. After getting it open I discovered the fan inside was wired to a circuit board which upon inspection was a timing circuit. This is why the fan still turned only too slow to function. The new fan was installed and my only problem with the fridge now is the ice maker, which I disconnected.Conclusion: Maytag actually designed this fridge to break down and require hundreds of dollars of repairs AFTER the warranty expired by installing a timing circuit that disables the fan that drives the cool air to the upper part of the fridge to keep your food cold and your freezer frost free. Replace the grey box with a normal fan and youll get years of good use out of your French Door Maytag! As long as you clean the seals regularly and dont mind buying ice to fill the tray with... The repair cost me $39 and a six pack of beer for my friend.

I purchased a Maytag washer on 7/23/11 from HHGregg. The salesperson told us they would highly recommend the new (HE) washer and said that everyone will start selling these only. So I bought your Maytag HE washer Centennial commercial brand. My complaint is my clothes dont seem to get clean. I have started putting less clothes in each load to see if that would help and it does not seem to help. When my clothes still come out smelling like my perfume and there are dry spots on my clothes, this tells me my clothes are not getting cleaned. I also have very sensitive skin. If my clothes were not rinsed good enough, I itch very bad. I called the store I bought this at and the salesperson I spoke with also said there were other complaints about HE washers. I wish I would have never bought a (HE) washer.

Bought the dishwasher (model MDB8969SDM0) at Lowes Burlington Canada beginning of September. After two months of use, the plastic pins and attachment to the drum, top rack broke and cracked in several places. Called Whirlpool Canada for repairs many times and got the run around, spent hours on the phone and still not resolved as of December 12, 2014. This model has a problem with the plastic and breaks continuously as seen by many reviews on the internet. The technician said that this is a problem with this newest model. I have now been waiting for over two weeks for the parts with no end in sight since they claim that the parts are back ordered. Called again today and was told that it would be another week to see if they can find the pieces. This is ridiculous, I paid over $ l,000 dollars for this model and it looks like now that I will not have it repaired by Christmas. Lowes refuses to help me because they have washed their hands since it broke after one month. I have been lied to many times by customer service at Whirlpool Canada. They claim that I am the first one to complain about this model yet the reviews on the internet are full with this issue. They say what you want to hear and do not seem to care at all. It is a disgrace, I feel totally cheated and robbed of my hard earned money. Maytag is no longer a good company for their appliances and service. I am starting to think that I am stuck with this machine and that they have literally robbed me of $ l,000. Shame on you Whirlpool and Maytag.

Our Maytag Elite Series dryer is not under warranty but we have had nothing but issues with this dryer since we have had it. However, now I have holes in the heat intake at the back of the drum. This is so very dangerous and could cause a fire. I am certain this is a manufacturing flaw. How on earth does the inside of a dryer have parts that will not hold up to heat? At any rate, I want it fixed. The only way to fix it is to replace the drum. This has to be a flaw in design or manufacturing and this particular model should be recalled.

Bravos 4.3 High Efficiency Washer - The worst washer ever. I recently returned from burying my step-mother. She actually used the same washer and dryer, by Maytag, for over 50 years. Those days are gone forever. This is my second set of Maytags in ten years. The first literally stopped working just after the first year warranty ran out. I still have them inside my pantry, like a set of anchors. Notwithstanding that, I thought, Maytag was a good brand, it must have just been the style of machines, so I purchased these in January. After over six months of usage, I am amazed at how many times I have to wash a single load of clothing to get the items clean. Who cares if the machine saves water? What was wrong with having an agitator? I literally have to remove freshly laundered clothing, turn it over and run the wash again to get the top of the laundry clean. I have had a blanket finish for the fourth time to get it clean, only to have to hang it outside because it is so full of water, the weight keeps it from spinning properly. And why would you remove a timer feature which permits very busy, working people, to wash their items while they are on the way home or in the middle of the night so that there is no waiting to pop the clothes in the dryer? None of the cycles takes less than 80 minutes to complete. Who has 80 minutes to wait on the washer to do its job? I am so upset about the amount of money I spent on all of these machines. Just think, I could have brought the over 50 years old set home from my step-mothers and had a washer and dryer do what they were supposed to do -- clean the clothes.

My $1,500 Maytag double oven Gemini has been trouble from the get go. 1st, trying to broil something cannot be adjusted. It sits 3 to 4 from the fire & there is no 2nd shelf. The control knobs sit on top of the stove & its easy to burn them when cooking. The broiler has always smelled like its leaking gas. Plus, the bottom oven stopped working & we had to get it repaired. The last straw was when the control board went out. We arent even going to try to repair, just going to buy a new stove. No Maytag!

148013 Stan & Pauls Dartmouth MA - 3 yrs ago we remodeled the kitchen... I went with Maytag appliances because I was always told they were good. I should have stayed with GE. Dishwasher touch pad is gone again... 2nd time in 3 yrs. Last one cost us 265.00. We are senior and thought these appliances would outlast us. We only use it about twice a week. Our freezer door tracks and door needed to be replace 6 mo after purchase. WE lost all the food that had defrosted. Our oven coil burned out already also... that was expensive to replace. Only thing that we have not had to repair (knocking on wood) is the microwave. STAY AWAY FROM MAYTAG, FOLKS!!

Our 26 month old Maytag fridge (Model MFF2258VEM8) was the french door freezer on bottom modern style fridge. The freezer stopped working. The repair shop took the fridge away and repaired a leak (quality control issue) and then the compressor failed in a test. They wanted $700 to make a repair that would have a 90 day warranty about 1/2 the cost of the fridge. Maytag was contacted at multiple levels and they would not even provide a free compressor or provide a substantial discount on a new fridge. What a way to treat a customer who once had all major Maytag appliances in our home. We decided to get a GE Profile fridge and are very happy with it. I will never buy another Maytag appliance. I dont think it is the great company it once was years ago.

Before today I was happy with my washer. Well yesterday I heard this loud noise. It turns out to be the gear case on my washer. To my surprise the repairman told me that it would cost between $450 and $500 to replace. I called Maytag to check on the 10 years warranty and was told that it would cover the basket and the motor but not the gear case. That is very stupid because without the gear case the washer will not work. This gear case help the sensor work, the basket work. DO NOT BUY ANY A MAYTAG PRODUCT. They do not stand by their product. I have had my washer for 2 years and 10 months. Before this the last washer I purchase was a Lady Kenmore through Sears. I had that washer and dryer for 25 years.

I love the functionality of this Maytag refrigerator. The inside is so nice and big, I can almost fit anything into it. When I need to make a lot of food for a lot of people, this refrigerator really foots the bill.

I have to agree with all these other reviews. This washer twists clothes and does not wash them at all. If you open the lid mid cycle you will see dry clothes on top... Isnt that the whole purpose of a washer? WTF. Steer clear of Maytag. They realize that theyre selling washes to Generation Xers and they can get away with it because we were the first throwaway generation. Great business plan Maytag!

Maytag needs to step up and admit that they have a design flaw in this dishwasher. The problem is that just a week or two after the warranty is out, it just stops working. Sometimes when you walk by it, it just turns on. No way to turn it off. Nothing works on the control panel. From what Ive seen on the internet, everybody is having the same problem. Its the control panel. It costs 180 dollars to fix, but it only lasts another year and you have the same problem. Ill have to say that when it works, it does a superb job. It just wont keep working.

I bought my Maytag Bravos washer and dryer set about 4 years ago when I moved into my home. The performance of the washer has always seemed mediocre. Despite using the correct HE products, clothes dont get as clean as with other washers I owned. Many times the washer becomes unbalanced, gets the UL code and I need to move my clothes around to get it running again. A few months ago, the washer started a new behavior: stopping during the initial fill cycle and displaying an F1 error. I soon figured out if I hit cancel and then start again several times, it would resume filling and proceed with the cycle. Over time, I had to repeat it more and more. I read about other complaints and suggestions on the internet and tried pulling the plug for a few minutes to reset the control panel as well as turning off the breaker to reset the machine.After troubleshooting the problem for 15 minutes or longer, the machine eventually runs. Then I can run subsequent loads with no problem. After a week or longer of doing no laundry, when I try to start the machine, I need to go through the entire process of canceling the wash load and terminating electric power to reset the machine. I have called Maytag/Whirlpool and got unsatisfactory answers. I only wash two to three loads of wash about every ten days and sometimes even less. The 800 number for Maytag was automated and would only schedule a repair without asking about the specific problem or being able to talk with a person. There was no way to cancel the service call scheduled and I had to call another 800 number to finally speak with a Whirlpool representative who tried to help me. She connected me with A&E Factory Service to cancel the service call.Both representatives stated that most likely the control board is the problem and the cost for diagnosis would be $130 plus the cost of parts, which could run from $200 to $400 since Im no longer under warranty. I canceled the service call as the cost of repair would be easily be almost half or more of the cost of purchasing a new (and different) machine. This is the electronics module, something that shouldnt be worn down or broken by use or even user error. This is an integral part of the machine and if it has a fault (which it clearly does), the manufacturer needs to stand behind it and help the consumer. The customer service manager even admitted that models with other model numbers had had similar problems and a free control board was sent to those customers. But my model was not in that range.”I had purchased a Maytag Bravos dryer at the same time as I purchased the washing machine and the dryer had a problem within a week of the warranty expiring. A service repair person came to my home to repair the dryer as it was barely a year old and I did not use it for several months that year (due to other reasons). From the volume of complaints Ive seen online, the Maytag Bravos washing machines should have been recalled and repaired or replaced free of charge.

I purchased a Maytag electric dryer Bravo 300 Series in November 2009. December 2011, the main computer board went out and had to be replaced. Do not purchase Maytag appliances. They do not stand by their defective products. First and last Maytag purchase.

This dishwashers start button stopped working after 1 1/2 years. We did not buy the Extended service warranty. So we are responsible for the service call and the replacement of the control panel. Ridiculous. I called Maytag to file a complaint and they never returned my call. I will NEVER buy Maytag again. There are enough problems posted to know better. This company should be ashamed!!!

I purchased a Maytag dishwasher four years ago and it has been serviced six times in those four years. Not just small things, main parts. Control board twice, control panel twice, and cleaning terribly the other two. They replaced the control board once and then would not do anything after that. I just got it replaced four years into this nightmare only because I bought a Sears home warranty plan and they are replacing it. I would never buy a Maytag appliance ever again.

I have a new Centennial Maytag dryer. What a horrible sound it makes when the time is up!!! I had another Maytag dryer for 19 years and it did not sound as obnoxious as this new one. HELP!! I can tell some man invented it.

I called. I was told nobody else ever had that problem. She hung up. I called again. The french door is nice to look at but it does not seal properly and there is CONSTANT build up of BLACK MOLD no matter how much cleaning. It returns. There is no other design for a seal either. There are several creases in the gaskets and there is mold in all of them no matter how deeply cleaned or sprayed. The seal is poorly constructed. DO NOT BUY THEIR FRENCH DOOR... Also their ice maker shoots ice all over the floor.

I bought this washer from Lowes in 2013. It worked okay for a little while but lately it stops mid-cycle. Clothes are soaked and all of the soap hasnt been rinsed out. Poor excuse for a washing machine! Will never buy a Maytag again!

A year or so after purchasing our new home, we purchased new appliances. We thought Maytag was a good company to go with. We had serious issues with our 2005 Maytag bottom-drawer freezer refrigerator right off the bat. It arrived with a large dent in the door. They offered to take $50.00 off the price. We insisted on one without a dent. They replaced the refrigerator, and shortly after, the board and the ice-maker went out right away.Although the parts were under warranty, we had to pay for the labor. The refrigerator is 6 years old and now it is making a constant knocking sound. We paid a lot of money for what we thought was a quality appliance. What a joke. We had also bought a new Maytag washer and dryer set and they fell apart after 5 years. It’s the same with the Maytag dishwasher. Do not buy Maytag appliances. They are cheap. They fall apart. The customer service is poor. I feel cheated.

Not long after dishwasher MDB7609AWB2 was out of warranty the START switch on the keyboard would not work. Called dealer and they sent someone out to check for a charge not quite $100. Could not fix it so said it needed a new control panel which with labor was almost $200. Doesnt work so get it fixed. Now less than 3 years later the same thing has happened - wont start. Lousy engineering and part probably made in China to save Maytag money, I feel is the cause. This is happening over and over to those of us who purchased in good faith what used to be a reliable product from a reliable company.

We purchased our Maytag® 4.5 cu.ft. White Front-Load Steam Washer online through Menards and picked up the washer on Feb. 5, 2022. We set it up on Feb. 6, 2022 and it didnt work properly from day one. The washer makes a clicking sound when it spins and also gets out of balance very easily. I contacted Maytag and they referred a warranty repairman in our area. He looked at the machine and said it could be one of two things and it would be a major repair. We would have to haul the washer to his shop and he would have to tear apart the washer to fix. He said it would be a big job to fix and we would be out of a washer for a few days.I also had contacted Menards shortly after we purchased the machine and they told us to contact Maytag. They wanted nothing to do with us and didnt want to stand behind a product that they had sold. Getting major warranty work done on a NEW washer makes no sense to me. I am very disappointed in Maytag and will never purchase anything Maytag again. Dont bother wasting your money like we did!

I have a Maytag side by side. In the first year, the ice maker failed and I had to replace it (in warranty/no charge). In the fifth year, the compressor failed (no warranty) and it hasnt been replaced. Since then, I have been looking at reviews and warranties of new refrigerators. The warranties (unless you want to pay $3,000+) are all one year limited. The reviews are scathing and it doesnt matter what brand. My question is, why dont you/we all get together and file a class action suit and demand millions in damages? Complaining wont get you anywhere with these people; however, hitting them in the pocket book will make them pay attention, especially if the penalty is severe enough.

We purchased a MAYTAG refrigerator when we recently built our present home. This refrigerator has been a nightmare! Ice forms in the bottom freezer and then constantly melts out of the bottom of the appliance all over the floor. Weve had a number of service calls with no real effect. The computerized function that sets functions do not work well and often shut down the appliance with little clear way to start it up again. The ice maker/dispenser often clogs up or will not produce ice. Weve had it! We broke down today and spent the money on a new GE refrigerator. My very strong advice is DONT BUY A MAYTAG refrigerator with the freezer on the bottom!

We bought a Maytag Bravos XL assuming that because of the brand name it would be a great machine. WRONG. This washer is truly awful. Every single load of darks comes out covered in soap scum. I always have to rewash every dark load with no soap for a full normal cycle in order to get the scum off. My whites are probably also scummy but often I just throw them in the dryer as I cant see the scum. Its just a very, very poorly designed machine that obviously wasnt tested before they started manufacturing and selling it. Its criminal how Maytag continued to sell this piece of junk, and Ill never trust their brand again.

Maytag Dishwasher MDB77495 - We bought this dishwasher September of 2013. April 2013 when you pressed the option I wanted the options auto clean, rinse only, steam sanitize and delay hours. The thing would work when pressing start but I have no idea what it is doing. The repair man replaced the board and all was good for a couple of months then it happened again. The board was replaced again and in two more months it failed again. The repair man told me that moisture was getting to the board and there was corrosion on the ribbon mentioned in another review here. He contacted Maytag both times and gave them my contact information but they never called me + they told him that they have never heard of this happening with this machine. We had a Maytag machine 8 years ago where the board actually melted but like an idiot decided to try them again. I will never buy a Maytag again.

The dishwasher is very stylish and looks great in our kitchen. I do wish there was a small knife drawer in top. It cleans very well and is super quiet. I would highly recommend this dishwasher, good value.

I have a Maytag dishwasher; a nylon roller for the upper rack cracked. It is held in place by a hex head screw. The roller is about $1.75. Maytag will not sell me the roller. I have to buy a complete rack adjuster assembly for $46 to replace a small nylon roller that screws in. I have had these problems before with them. I guarantee that I will never buy another Whirlpool-manufactured appliance. This is ludicrous!

Our brand new Maytag dishwasher model number MDB87749SBM2 was professionally installed on 7/31/2013. In fall of 2015 my control panel started acting up. I was unable to select certain wash cycles. The problem would come and go. By January 2016 my lock button would freeze and I was unable to unlock or select any wash cycles. By February 2016 my control panel went out completely. It wont turn on, not a single light. It is fried.When Googling the issue I found that we are 1 of MANY with faulty control panels not only on our particular model but on many Maytag dishwashers. They all seem to have the same problem, right around to 2-3 year old mark. One would think dishwashers would last, like before. A dishwasher shouldnt need to be replaced or need a major repair so soon. The one our new dishwasher replaced was 12 years old and was working just fine. We just wanted to upgrade to stainless steel. Wow what an upgrade haha! Maytag should be recalling these control panels. Their name is no longer a trusted name in our home.

I purchased the Maytag Bravos 400 series top load washer about 4 years ago. Paid over $1000 for it, on sale. Its bearings started grinding within four years and the seal is gone which has resulted in water leaking out through the bottom of the machine. VERY expensive to repair and ultimately not worth it. Pretty disappointed that Maytag products reliable for such a short period of time and must then be kicked to the curb. NOT a quality product.

We purchased a Maytag Dishwasher (model number mdb6759aws3) about 3 years ago. After about 1 year, the control panel started to go. Certain options would not light up. If I used the options that did light and shut the door, the dishwasher would work. I had called Maytag, and they were charging almost $200.00 to come out to repair. Now after 3 years, the entire panel is out. We had someone come out. We ordered a new touch pad for $265, and it still did not work. It is the control panel that is dead. What bothers me is that after reading online, this seems to be a continual problem, and Maytag does nothing to help the consumer.

The door is worthless. I am the only washing machine user in my home and am gentle with my appliances. However over normal use, the washers door has cracked and has had to be replaced twice since it was purchased from Home Depot.

Maytag top loader washing machine - Worst appliance purchase ever made. Does not clean laundry, takes all day to do 5 or 6 loads. Not enough water to properly wash or rinse load, even using the deep water setting (a joke). A load of 2 king size sheets and 4 pillow cases wadded up in a ball and rattled around so hard in the spin cycle, it pulled the plug out of the wall. Maytag sent out technician who conducted diagnostic testing, which did not include any actual laundry. Technician said machine was operating as intended and verified I was using the machine properly. I have tried to return this machine since the first load was done and realized it was a disaster. Maytag refused to help. In fact, their phone agent had the audacity to suggest I wash one sheet at a time to prevent the machine from moving across the floor so far the plug came out of the wall. Maytag surely is not what it used to be. Im sorry I did not know they, like so many other companies, dont care about their reputation or customer service, not to mention producing a quality product. I would say they are actually misleading their customers by calling this product a washing machine.

Bought this Dishwasher two years ago. Control panel was working intermittently now it does not work. I am looking for anyone with this same problem. I know lawyers who are class action specialists who fight for the consumer. We need to make Maytag responsible for the flaws they have in their product. From reading these other reviews it seems that this control panel issue is consistent no matter what model you have. They must all share the same electrical components that is causing this issue with the control panel. My model number is MDB8959SBS2.

I purchased the Maytag Neptune pair in 2002 and was never informed of the product recall/class action lawsuit for the washing machine which occurred sometime around 2004-2005. We have had many problems with our washing machine over the years and ruined many clothes with what appears to be bleach stains, even though no bleach was used in the cycle of wash. I had to replace the board which controls the latch on the door and the clothes that are washed are not clean and have an undesirable odor to them. I would have been part of this class action; however, I was never informed of the lawsuit. I called Maytag today and they advised I could set up an appointment with a service person; they did not want to honor my complaint as the class action lawsuit has been resolved and they are not handling these types of complaints anymore. My children have started a new school after semester break and their brand new uniforms are now becoming ruined due to this defective machine that Maytag will not take responsibility for. What type of recourse do I have? I will never purchase a Maytag anything if this is how they treat their customers. Problem will not go away by hiding their head in the sand. Now I have to go out and purchase a new washing machine because Maytag didnt inform their customers of the inherent defect in their product and take care of them accordingly.

Bought a Maytag front load washer. When it is operating it is very loud. Some parts of the washer are made of cheap plastic. The Optimum detergent dispenser also of cheap plastic failed after 1 month. Disappointed in finding out only the outside metal box was made in America. All inside components are made in China which raised the cost $300 due to recent tariffs.

I just bought my first home and after well over 20 years of apartment living and not having my own washer & dryer I was so excited to finally be able to buy one! I decided on the Maytag/Bravos and even spent the extra $100 for the glass top. The high efficiency machine was delivered on August 8, 2016. My kids are grown so its just me; I do one load a week give or take. A week or so ago, I noticed the washer was taking an inordinate amount of time to go from sensing to washing and even longer to get into the washing cycle. This past weekend, it didnt work at all. Just sat for hours with the sensing and washing lights on, without actually washing the clothes. The machine was packed loosely with the correct amount of High Efficiency Detergent in the proper place. I called the #Sears store I purchased the appliance from (Braintree Ma.) and they said there was nothing they could do as it was past 30 days, gave me their customer solutions number which is basically a call center with people who I could barely hear and/or understand. They in turn gave me more phone numbers which seemed to me to be in the same call center. I want to return the 4 month old washing machine that doesnt work and I want my money back. Ive filed a report with the Massachusetts Attorney General Consumer Affairs Department. I will NEVER AGAIN shop at #Sears and I will NEVER AGAIN purchase a #Maytag appliance. I am beyond disappointed in #Sears and #Maytag, both names that used to mean quality and customer service. And if theres a class action lawsuit to be filed, please count me in.

I would like Maytag to repair or replace this dishwasher. It has only been installed since November 2014. The only button that works is the auto clean. None of the buttons work. I thought Maytag was a reputable business.

Let me make it simple for you, DO NOT PURCHASE A MAYTAG/WHIRLPOOL product. Maytag/Whirlpool believes its products should work for 1 year and then become obsolete, at least this is what the Maytag/Whirlpool customer service line told me. I purchased a MVWB950YW (Bravos XL) top loader on September 4th, 2012 for $948.00 plus $99.00 for an extended warranty. The washer worked marginally well when it was brand new. June 2014, the washer in spin mode started to sound like a freight train was about to run through my house. When I called for service the service company immediately signaled it was a bad bearing and offered me $500 to put towards a new or refurbished Maytag!!! They claimed if they were to repair the machine it would VOID the extended service contract?? I wanted the washer fixed, I did not want to spend more money to buy a new machine. I continued to use the machine as is, with the incredibly loud noise. June 2015, the same machine starts to leak water and is even louder. Again the company in charge of the service contract offers money for me to put towards a new or refurbished machine. Net is, Maytag/Whirlpool engineers its products based on its warranty - 1 year. Anything after that they view as an opportunity to steal more money from you and I the consumer. Do yourself a favor and NEVER purchase a Maytag/Whirlpool product. I would like to think American products are superior to its foreign counterparts, however Maytag/Whirlpool is not in this league. In my opinion, Maytag/Whirlpool has lost the privilege to call itself American and should no longer be allowed to do business in this country.

I bought my Maytag Refrigerator about 7 years ago and the night mares have not stopped. The ice maker has broken down so many times, I forgot to count. The drip from the ice maker lands on the floor of the freezer and drips out to the floor. The cold part of refrigerator end up freezing the fruits and veggie and milk.

Refrigerator (Model Mff2558vems) purchased end of November 2011. Early in 2013 notice refrigerator first forming ice all over freezer, including an ice sheet on bottom of freezer. Then noticed water around refrigerator. Called maytag and they sent repairman even though a little over year and out of warranty. Their service people seemed to know exactly what was causing the leak as they came in with the correct replacement part. Worked fine however, there was damage to my newly refinished hardwood floors which Maytag did pay to repair. A couple of days ago I opened the freezer and again noticed ice all over freezer. The next day, water all around freezer. I cleaned everything up, so I thought. The day after, we noticed the hardwood in kitchen buckling up far from refrigerator and the laminate in dining room bubbling, even though there was no visible sign of water. Called Maytag repair company but they couldnt come out for a couple of days. Called another local repair service familiar with Maytag refrigerators and he couldnt find anything wrong with refrigerator even though he knows leaking caused by refrigerator. Called insurance co. and they sent over service master. Leak is definitely coming from refrigerator. They had to pull up hardwood floor, part of walls, the dining room. They now have five large fans going and a defroster to dry things up. This is upsetting, as my daughters wedding is next month, my husband is currently laid off and I dont need this kind of aggravation again. I love the french door idea, so roomy for my large family, but I am now afraid of this refrigerator. I dont want it but think it is ridiculous I have to shell out more money when the refrigerator is less than 3 years old. I talked with a higher level supervisor at Maytag and they are only willing to give a 100.00 rebate towards a new refrigerator since the refrigerator is out of warranty. This is ridiculous. I thought by buying American I was helping our economy but what I got in return is heartache and crappy merchandise. If there is a lawsuit in California against Maytag about these refrigerators I want to join. My friend in N. CA who bought her Maytag refrigerator the same time I did is also experiencing leaking. So frustrating.

My Maytag (MER7662XQ) oven has stopped working after barely 6 months of use. I filed a warranty-repair complaint and reported the error codes shown: F1 (faulty touchpad) and F3 (faulty temp sensor). Although Maytag promptly sent a repairman, he arrived without parts and left within 5 minutes without fixing anything. He said he would order parts. Whenever they were delivered to us, by mail, we should call again to schedule another repair. But he warned he was prohibited from coming out for another 7 days. So far, Ive been without an oven for almost 3 weeks and there has been no action or information. My calls to Maytag produced nothing, except confirmation they show the repair as open since they do not actually distribute parts, and the repairman is with an outside company. A terrible product and a worse service! I would not ever buy another Maytag product and recommend that no one else does either.

If I can rate the AquaLift Technology oven cleaning system that my Maytag oven has as a “Zero”, I would. This technology only removes some of the spills on the bottom of the oven. It does not clean the sides or top of the oven. I’m back to the olden days of using a lot of elbow grease to remove splatters and spills. They say you cannot use any cleaners in the oven either. At least with the old ovens you can spray an oven cleaner and wipe it clean. This product has taken us back before there were spray oven cleaners!

Purchased Maytag Centennial Washer and Dryer (MODEL MVC300VWI) at Home Depot 3 yrs ago. After 6 months, washer started to rust. Maytag told us It was not their problem. A 6-month old washer should not rust! Poor quality + poor customer service. Dont buy!

We purchased our washer Model # MHWE450WW01 and Serial # CS10502122 on March 30, 2011 along with a front loaded dryer and refrigerator on March 30, 2011 from a local store Appliance Outlet in Duncansville, PA. As with most new purchases we were excited as all three of these appliances being replaced were 20 years old. All were installed and worked great. My wife and I would often comment that in the spin cycle the washer sounded like a jet engine readying for take off. At some time in early 2014 we had Appliance Outlet come out and inspect the washer and told us that the washer was not to be that noisy and they would authorize replacement parts under warranty. In calling Maytag we were treated well and the parts came. Rear tub W10772619, Basket W10283352, Front tub W102823352.One of the parts was in fact cracked when it came in and had to be reordered. It was and several weeks later it arrived and Appliance Outlet fixed the washer. It ran so quiet we could not believe it was the same machine. In late spring of this year the noise was back. Appliance Outlet confirmed that indeed the same issue was happening and we would need to replace the parts again. In early June 2105 I called customer service and explained the situation and the rep took the notes and stated that we could indeed get these parts replaced and we as homeowners would pay for the labor. As YOU would I tried to get the labor paid for and was given the company line policy and told that there was NO way Maytag paid for the labor and the parts would be shipped. I accepted these terms.Yesterday my wife called to find out the status of the parts shipment and was taken for all intent and purpose right back thru the initial call routine. NO record of my call in early June existed and the best she got was that if Appliance Outlet would call and order the parts that they would be reimbursed. Appliance Outlet said that is NOT normal warranty procedure. Normal warranty goes from Maytag to the appliance Owner. They only confirm the issues/problems and do the labor. I am now stuck. I am also CEO of a company and while it pales in size the buck stops at my desk.

After reading all the reviews I realize this is a wide spread complaint. After 2 1/2 years the control panel on my Maytag Dishwasher will not work. You press the keys and hope for the best. I am thinking of going to the media with my complaint. Maybe we will all get some sort of refund or upgrade.

I purchased a complete Maytag set for my kitchen (fridge, double oven, microwave, dishwasher) from Home Depot on November 22nd 2012. About two months ago I noticed the dishwasher started to glitch here and there, but was still functional. I removed the panel and found that the wiring was completely corroded and would need to be replaced. I put everything back together and have managed to make it almost a month on the same cable. In the mean time, I searched for my receipts, my manuals, and anything else to show my purchase given the 10 YEAR WARRANTY Maytag wants to mention as a sale point. Aside from Home Depot not being able to find my order information to duplicate the receipt, I managed to find where I had ordered my set online and was emailed a copy. Home depot is not involved with the warranty process, unless you purchase the additional warranty. They deferred me to Maytag. I contacted Maytag and was informed that the warranty only covers the stainless internal tub, the racks, and the chopper. Seriously?? So, absolutely NOTHING mechanical about the product past one year.After paying the $699 for the washer, and another 57.99 for installation and kit, I was told by Maytag that I could buy another 1 year warranty that would cover the part, but it would cost me $289, or roughly half the price I paid to get a whole two years out of the dishwasher in the first place. This means I might as well be paying almost $300 a year just to have this product... ridiculous!! Just to buy the part and do the work myself, the part is $172 plus tax/shipping. Since it is only 4 screws and a couple clips holding this thing on, I am likely going to go that route.I have read many people saying similar things about the electronic wire corroding and this appears to be a well known issue with their products. They recommend sealing the entire area using a tube of silicone to help reduce the amount of time it takes to ruin another cable. Very very very poor craftsmanship. Nice racket they have through charging people so much every couple of years for their products!! As my $4000 kitchen appliance set falls apart, I doubt I will ever replace it with another Maytag item.

We have a 4yr old model MFI2665XEM7, just started leaking water every other day. A puddle wipe it up and its gone. Have ice build up on the bottom of freezer. Any suggestions on what to do?

I purchased an LG (white) washer last year, but my husband upgraded all appliances to stainless, including Maytag washer and dryer. The washer does not fill with enough water to cover the clothes. It barely agitates them to wash. Some clothes even come out with dry spots on them at times! They smell and are still dirty when done. I have tried every setting hoping that was the issue. Normal, power wash, none work any better! Had to resort to the soak function which does not add fabric softener or drain the water completely. Thankfully I didnt sell or get rid of the LG. Putting the LG back in asap. Nevermind the mixed color finishes of white and stainless between the washer and dryer. Clean clothes most important! Piece of garbage and complete rip off!

Oven does not have consistent temp, cant change temp without preheating ruining whatever is cooking. 5 visits from Maytag during added warranty and never any satisfaction. Tough Microwave minutes and the oven goes off. Told it was a Govt requirement. Very noisy even after its off. Maytag wouldnt help or Home Depot either who warranty was through.

Bravos gas dryer - three issues in three years. Same issue twice, clothes are not drying. Now I have company coming and have to deal with his issue. The blower motor went. So, I have paid for a new dryer in repairs already. The washer is making such a loud noise when it goes into spin cycle that you have to turn the volume up to the highest level on the TV and it is still tough to hear. It’s unbelievably in the horrible quality. Make the product and parts in the USA and stop buying junk from China and Mexico. This is good American money that is flushed down the toilet with Maytag as well as your reputation. Fix your quality control and do the right thing!

Purchased new stove from Home Depot. Was delivered damaged after I opened it. Called Maytag and they cannot get a service man there to look at it. They keep on telling me I have a 30 day unconditional warranty, yet they cannot live up to their words. Absolutely amazing. Bought the Maytag because of the 10 year warranty. Do not waste your time. Buy locally at an appliance store not big box stores. Do not buy Maytag either - service is just a bunch of well qualified talkers and key punchers. Very poor buying experience.

We purchased this Maytag Centennial washer in 2009 (model # mvwc6esw/Wd; type 849-05; ser # cy1741855) and I have hated it ever since. I had an old 406 Maytag washer that was worth its weight in gold - repaired it as long as possible. I bought this new one because it was a Maytag and that was a mistake. The way it agitates my clothes get tangled and they never did that in the other original Maytag. We had to have it fixed not long after we got it and now every time I turn it on, it immediately starts to agitate on every cycle except hand wash, which it never did before. If I knew it agitated the way it did, I never would have got it. Good thing we bought an extended warranty for this machine. We have used it once already and it looks like we may have to use it again. I am very disappointed in this machine and your workmanship. The old machines were much better and more dependable.

So this washer, Bravos MCT cleans good not great. Saves water but clothes dont always come out clean or smell fresh. We have had it for just over a year and the control panel stopped working. Warranty is good for only 1 yr. UGHH!! It is all one unit so the complete circuit board had to be replaced. Half the cost of this washer new! I saved money by replacing it myself. Took 15 minutes. Very easy. Disappointing when you see this is a come problem with this model.

After the 4th service call Maytag wanted a 2nd company to look at it. So on July 27th A&E out of Bristol, PA came out. He checked it out and said its not serviceable because theres a leak somewhere in the casing. Had to call KYW 3, On Your Side, they helped me get some progress. Jacqueline from corporate called and said they would replace it. It started on July 3 and now August 13 and still no fridge. Had my Maytag washer fixed, small problem. Parts came in a box marked Whirlpool for a Maytag washer from a Sears Warehouse. Plus the mechanic said my Maytag refrigerator is made by Amana. Buy American?

We purchased a top of the line, state of the art Maytag washer and dryer Neptune. The fill valve failed twice, flooding the first floor and the big storage room below. Thank God we were here! Now the thing halts mid-cycle and wont continue. The repairmen both said the design is messed up and they hate to work on the Neptunes.

Our washer ran great until last week. Had repairman in. User interface died after 18 months use. $250 for the part plus labor. This is a $1000 washer. Buyer beware. Maytag is just another name for any washer in the Whirlpool lineup. Uses the same parts. Has the same issues. Should have bought a Speed Queen.

We purchased a new Maytag dishwasher last year when we purchased our new home. All the other appliances were Whirlpool. This dishwasher runs forever. We have huge electric bills and I am sure this is a contributing factor. We purchased it from Lowes. They have sent out two technicians who say there is nothing wrong with it. One said it was because it was in an island. The other that our water is not hot enough. He turned the water heat up and now you have to warn people using it to be careful or they will get burned. No wonder the Maytag repairman is so bored. He knows the appliances he services are junk and doesnt bother. Take my advice. Buy ANYTHING BUT Maytag!

We bought a new top of the line Maytag MGD7000XW dryer about 2 years ago. It worked great for about 6 months, thing started acting funny. All of the front console lights stay on all of the time and it ONLY dries on high heat now. This all happened after the warranty period. So fine, I was going to buy a new complete front console (CONSOLE Part Number: W10388467 $300.) as the online repairman suggested. Guess what, Maytag no longer offers the part to fix my dryer. So now I have a 2 year old top of the line P.O.S. MAYTAG dryer that cant be fixed. I will never buy from this company again (Maytag).

Maytag Bravos XL - I purchased my maytag washer & gas dryer on 5/12/12. In Dec 2012 the heating element went out. I had to wait a week for a repairman to come out on Dec. 20 to fix it. Now for the second time on Dec. 30th, 2014 the heating element has gone out. I called for a repairman to come out. I have to wait until Jan. 12th 2015 for service. I have 8 people in my home including 3 grandchildren. This length of waiting is ridiculous and very inconvenient.

Purchased washer March 2017 and had to get it repaired twice by the end of 2018. The top loader even with agitator does not clean clothes very well. The repairman said not to fill the washer above halfway so I can only wash about 4 pair of my husbands heavy soiled work jeans. I won’t buy another Maytag.

My Maytag dishwasher will not come on and it is loaded. The control panel is out for the third time.

First of all, I had a Maytag for many years and could not have been happier. When it came time to replace, I did not even consider other brands. I have had my dryer for less than a month and the interior already looks dirty. I contacted Home Depot where I purchased it and reported the problem I was having and would like to return this model and purchase a higher end model assuming that it would not have the same problems. Home Depot said all appliances are special orders and can not be returned. I could contact Maytag and have someone come out and look at it for no charge. I contacted Maytag and they told me that they could have someone come out but if they decided it was just cosmetic, there would be nothing that could be done and I would be charged. I said, I am telling you it is cosmetic! Why would I pay someone to tell me that? The guy suggested I take a damp rag to clean it. I said think about all clothes that are being dried are damp!! I will never buy a Maytag again and will not buy any appliances from Home Depot!