I purchased a Maytag dishwasher on Oct. 12, 2013. The control panel failed in July 2013 and had to be replaced. I was unable to program a wash cycle and the lights would move all around the front. After the first failure, I was told that the control panel would only be covered for 3 months - the original purchase date for the washer, NOT the date of the NEW control panel. I was then talked into an extended service plan. Now, four months later, the control panel has failed again and I am unable to program a normal wash. A repair man is not scheduled to come for another 9 days. As a single homeowner, this product is not used even on a daily basis. I will never purchase another Maytag washer. They do not back their product with appropriate repairs.

My grandmother got a Maytag Bravos XL MVWB755 washer and from day 1 she had to call Maytag with issues due to residue left on the clothes. They told her to not use this setting... buy this detergent... only use cold water etc. Never did they offer a repair guy to come out. A year passes still having issues shes out of warranty. They now offer a repair guy but claim theyre going to charge her $90. Once she explains to them that she was never offered a repair guy & they shouldve done this before. They decided to waive this fee and send a repair guy. Once the technician comes out to the house they do absolutely nothing and they fill it up with water say we need to clean it and Ill come back out and do another diagnostic. When they come back all they do is fill it up with water get a glass check the water and say, Nope, no floating residue. Everythings fine. They then tell her she needs to get a water softener which is going to be hundreds of dollars.The technician also says do not use any other settings except for these two. Can someone please explain to me why they have all these dang buttons and settings if were not supposed to be using any of them and why all of the clothes come out with soap residue scummy residue all over them? The old washer never did this. It was a Kenmore and its the same water same everything but this Maytag washer is been nothing but problems. It leaves the residue which is stripped all over dark and white clothes, it is extremely loud, not all the clothes even get wet! Maytag is been extremely uncooperative with assisting my Nana. They tell her no one else not one other person is having this problem but when I look up this issue I find that about 2500 people on this forum are having very similar problems. Something has to be done. Maytag should have to take responsibility for this washer. The bottom line is it supposed to be an XL. When my grandparents are washing its only for two people. Theyre not even filling that washer up of all of the clothes are not even getting wet. It just goes to show you that the energy-efficiency that they claim is not working. The washers not getting enough water inside of it. Its not fully rinsing the clothes and no one should have to put the clothes in wash them then do a whole another rinse cycle just to get the dang soap off. So basically at this point she stuck having to do multiple washes using way more utilities than she should have to and Maytag is basically going to do nothing. It wont help her over the phone the technician is a joke and it looks like so many of you people are having the same issues.

Its frustrating the way the bottom of the dishwasher has curves making wasted space. Second, the tracks for the trays are such that often the tray comes off the track and makes it difficult to get back on without unloading dirty dishes to do so. Finally, I really dont get the lighting system for dishwashing on the outside of the machine.

This model MGR5875QDW range is very difficult to use. When you press broil for instance, the display says set. There is absolutely no indication of how to set. Therefore, no broil. The same thing happens when you try to use the clean function. It is virtually impossible to use the control panel; it is just too difficult. Therefore, most of the functions are not usable.The kicker though is that the handle comes off. During the extended warranty period, a technician came out and fixed it. The toughest part of this job is to get the oven door back on. I tried for 2 hours everything I could think of. Then, I got an idea to use Maytags live chat. They told me that I would have to call for service and pay for a service call to get the door back on. I told them that their clean cycle is too painful to use, so I am assuming I am not the only one who has removed the door to clean the oven. Pay for a service call every time I want to clean my oven or fix their defective handle design because the handle falls off every 2 years? That is not acceptable.

We are having the same problems with the drain clogging and bottom of the freezer filling with ice and then water all over the floor. We currently de-ice the freezer once a week. After paying top dollar for what is advertised as a top product, we expect better service. Especially when Maytag is fully aware of this problem. We sent an email of complaint to Maytag. Heard from them today. They would pay for the replacement part but not the labor. Most places around here charge $250.00 just to walk in the door!!! Is Maytag kidding?!?! NEVER AGAIN. Will also tell anyone who will listen to stay away from Maytag. No wonder they dont belong to the Consumer Resources group!!

Our Maytag ref. is not quite 4 years old and it is leaking water on to our floor. The ref. is a French door with water and ice in the door and freezer on the bottom. We have to clean up puddles of water at least 3 or 4 times a day. I see that this is not an isolated problem, as others have complained about this defect doing the same thing with their Maytag refs. Why hasn’t Consumer Affairs demanded a recall on these expensive defective refrigerators to date?

Maytag Dishwasher MDB7749SBW3 - Control panel problem just like everyone else describes. Bought in Nov 2014... how disappointing!! My husband is sure he can fix it if I buy the part. I went online to order the control panel, and of course because Im in Canada I cant ship the part directly from the website, I have to call the Canadian Sears Part Dept., its about $200! As I came across all these reviews I am even contemplating if I should waste our time and money trying to fix this thing... Maytag never again!!!

I am renting to own a Maytag refrigerator and it is leaking water on my floor. Runt my floor already - had to replace the floor once. Sent it back to the place where I got it for them to fix it. Paying insurance by the way that isnt worth a crap either cause they wanting to tell me that I left it open at some point or the lights was off at some point. Anyway to make a long story short they gave me the run around and didnt want to fix it. But how do you fight big companies? This was a rental company by the way rent to own so now I have 4 payments left out of 24 at 180.00 each and they still dont want to fix it. I dont know who to be madder at - the rental company or Maytag from selling this piece of junk. But by me renting to own it if any problems occurred they were suppose to fix it. Youre already paying twice the amount to get one cause of credit issues. But thats no reason to double screw someone or should I say triple cause you getting doubled the rental company alone. They need to recall this refrigerator. It has been a lot of complaint and they want to tell you to go behind the refrigerator unstop a line. Well I didnt buy this refrigerator to have to work on pulling it out from the wall every two days to do this procedure. This is crazy. Any one out there looking to buy a refrigerator my advice to you would be do your research and stay away from rental places whatever you do because you will pay twice the amount and they wont stand behind their promise either to fix it as long as you renting from them! And stay away from Maytag!!!

Our Maytag Atlantis dryer had smoke coming out and almost had our house on fire! Had it not for us double checking the entire house would have burnt down! The dryer is less than 10 years old and already it is tearing apart. I cant risk using it again. Terrible company. I would never buy Maytag products ever again!

Thank all of you for saving me. I was about to buy a Maytag with bottom freezer from Home Depot. No wonder they are marked down an additional 20% off their sale price.

The Maytag washer is very quiet & economical by filling the amount of water needed per load so actually a money saver. Also got the huge drum to wash quilts & blankets. My old one lasted 10++ years. Hopefully get as many years out of the new one.

We purchased all new Maytag appliances when we built our house. So far, the stove/oven has quit working and been repaired 3 times; its always the ignitor. The dishwasher has been fixed twice. The washer no longer spins out as it should. The refrigerator and dryer so far have run okay. I am definitely going to change brands with my new appliances. I will not purchase Maytag again. Its not what it used to be. I will do without oven this time, until I can buy a new one. Also, the dishwasher door has had problems from day 1, and now, it will not close at all. It seems like its off the hinge. Definitely, its not the Maytag of years ago.

I have not been satisfied with this Bravo washer since purchased 4 years ago. I have been holding back anger, hoping things would somehow improve. Clothes are never really cleaned, cant even fill washer with very many clothes because the washer goes off balance. It takes a lot longer to do laundry. Clothes spin so fast they are in knots when I put them in the dryer. I always have to iron clothes. Today, well today we have a leak coming from under the washer somewhere. So please tell me, what is the advantage to having a HE washer again? By the way, no warranty since its been 4 years. I will never buy another one.

Add me to the list of people who hate this washing machine. It does not use enough water to get clothes really clean, leaves spots, is hard on clothes and tears them up, and the spin cycle gets unbalanced too easily. It has taken me hours to wash one load with a blanket in it because of the spin problems. I have not been able to restart the spin cycle without starting the wash cycle from the beginning.

My microwave will not work when the door is shut. It says: Door open. It’s worked intermittently, doing this for about two weeks. Then my husband woke up one morning a week ago and the microwave was on like it was running, light on but the plate was not turning. So we’ve had to unplug it and do without during thanksgiving weekend. This seems to be a common issue, obviously from the reviews below, so shame on you Maytag for not owning up and doing the right thing, covering repairs or sending out a recall. It’s a $112 service call here locally plus parts and labor. I will certainly be telling others not to go with Maytag. Maytag is lucky- it turning on by itself AT NIGHT, WHILE WE WERE SLEEPING, that it did not cause a fire or something. I’m pretty upset that it’s inside a 2.5 year window and already has issues.

I bought a new refrigerator 6 weeks ago and it is not cooling or freezing anymore. I lost all my food. I spent 50 minutes on the phone to be told that the earliest they can fix it is in three days! Can you believe that? I will never buy a product from Maytag or Whirlpool again and everybody should be aware of the awful quality of their customer service!

3 months after we purchased our Maytag dishwasher in Jan 2014 (Sears) it broke. The service person told us that the ELECTRONIC CONTROL PANEL (START, CANCEL, WASH CYCLE SELECTIONS) was a common breakage issue and fixed it. It broke again around one year from our purchase date. Same issue, but kept working and not working. Finally we contacted Maytags customer service. Although courteous the only thing we were offered for this common Maytag issue was a $249.95 one year warranty for them to come and fix this recurring problem. I explained that we had already spent about $870 (including tax, delivery and installation) for our middle of the line dishwasher one and a half years ago and asked if they would consider either charging us for a smaller service call/repair or just do it because it seems to be a design and manufacturing issue. After one hour and no sympathy I had to pay the $249.95 to get a repair person out and be covered for one year from today. I dont trust the cheap quality and the lack of support for the product. THEY ARE OUT THERE TO SELL MORE INSURANCE AND CUSTOMER SERVICE DOESNT MATTER!

I purchased a new MVBW725BWO washer. The cycle use and guide chart is generic. It does not remotely match my model. I called customer service. No help. She told me to tell her what I am washing and she will tell me which cycle. Really? Every time I wash a load I need to call her/him? I am not a laundry rookie but this machine has many buttons and choices. I want to do the right thing. Too bad. I washed two blankets and continually get an UL (uneven load) indicator. I have rearranged these two blankets every way possibly and there is no clearing the message. I called Maytag. No help. She told me that I should either 1) unplug the appliance, or 2) trip the breaker. Are you kidding me? If I didnt like those ideas or find them useful, call back and she will dispatch a service technician. Laughable. I guess I can pull them out of the washer, drip water everywhere, hand wring them, and move on. What happen to the good old days?

Maytag Bravo washer and dryer delivered 2 days ago.My complaint is with the washer. I didnt know it was HE and that it requires special detergent! I didnt know the lid locks! I didnt know when I push the hot water button, the machine mixes in cold water! Complicated, delicate machine and not user-friendly. I dont expect the washer to last long.

I have been washing clothes in different washers for almost 4 decades and never had a terrible washer until now. It has total control of the water level and it NEVER has enough water added. I have to add at least 2 full dish pans of water to every load. My washer does not allow you to pick your level because it does it automatically and no theres way to bypass this problem. It moans and groans for almost an hour in slow motion at its best. It should be illegal to sell such crap!If the intent was to save energy it fails when it runs twice as long as other washers. The instructions that are in the lid say that when you set it on deep water wash that it does not sense automatically-LIES! This lid must be generically made for other washers that they have because again, you cannot choose a water level. When a washer runs for almost an hour (this is not soak or extra rinse either) it is not saving energy over those that run for half that length of time. I wish I had returned it, but I listen to others who say that this is how washers are now. I still owe 150.00 on it and hate writing that check.

Maytag topwasher 2011 model MVWB300WQ2, SERIAL C11271134 - Im from the old school, expecting to get my money worth. I purchased a Maytag Bravos automatic washer in 2011, now less than 5 years later, it has a very loud knocking noise during the draining and spin cycles.

Maytag gas range 5 burners. Maytag is quality. Period. I doubt that other brands are made as well. From the handle of the oven door to the ease of cleaning the burners, you wont find better for the price. I look for quality and reliability. I read reviews. A deal breaker on any major purchased would be too many bad reviews and shoddy materials or construction. This range has 3 regular burners, one large burner and one small burner. The oven shelves easily adjust from one level to another. The controls are easy to reach and the timer and bake controls are easy to operate.

After using my GE Profile to death we replaced it with a Maytag; mostly for the cost. Although I hate to admit this, remember the old saying you get what you paid for - Well its true at least in the case of this Maytag oven. I am a constant cook and own a bakery, I often bake many of my products at home. Since getting this oven I have had nothing but failures. The cakes are over done, underdone, cookies burnt, not cooked enough; my time frame for recipes is so off! I wrote a cook book and have baked for years so I know for a fact its not some miraculous mishap that all of a sudden I cant bake. Ive had them come calibrate the oven but still no success.Im going to call them again but I felt compelled to let people know this is the worst oven in history and avoid purchasing it at all cost. I plan on having the service team come out one last time but if this doesnt work I plan on replacing it. Its a Maytag Double Wall Oven-Top Convection-Self Cleaning model no: MEW9630DS-SS. BUYERS BEWARE!

Maytag Bravo 300 Quiet Series - Bought this Maytag 5 years ago because Ive always had good experiences with them. After 3 years it started making rattling sounds so we had someone come out and fix it for around $275.00. 2 years later its still rattling, leaving black grease marks and putting holes in the clothes. Will not complete cycle unless it is unplugged, reset and plugged back in. I give up, I just bought an LG. I will never buy another Maytag washer again, still have the matching dryer though.

We purchased a Maytag Front Load Washer in April 2011. We did not purchase an extended warranty. From the beginning, it didnt seem to clean as well as our 12 year old top load Whirlpool had. Then in Summer 2013 it began to create fabric pulls in fine fabrics - tablecloths, blouses, etc. Whirlpool sent a repairman who charged $90 to tell us that the drum needed to be replaced because of a rough spot. He ordered a new drum and we understood that it would be replaced because it was within the 5 year manufacturers warranty on drums, but we would have to pay for installation. 2 months later, Whirlpool informed us they could not supply the new drum. Why are replacement parts not available for a 2 year old machine? The customer service rep told me that they would replace the machine for 15 percent of the cost of a new machine. All I needed to do would be to pick out a machine and let customer service know the model number and they would make arrangements and contact me re: payment of the 15%. When I contacted them again I was told that I would be expected to pay $508.00. That is 15% of a $3000.00 machine. It it completely unfair. Later, I was told that the first rep I spoke to must have been wrong because they dont pro rate replacements on a percentage basis. I told them that I was not interested and they have lost a good Whirlpool customer. In the last 15 years we have purchased 7 appliances made by Whirlpool. Never again! I am not impressed by their customer service.

Bought a Maytag Stainless Steel kitchen stove to upgrade my appliance before retirement. 14 months later the spring loaded hinge failed. A bad piece of engineering in the way of a retainer pin to hold the spring pressure tore out of its pressed metal hole. The hollow pin was fastened in place by a 3 fluted punch instead of with a proper rivet with a head. My local parts supplier had 10 on hand so you know they are aware of this. $70 and an hours labor and it is repaired. My local seller said, Too bad you didnt get the extended warranty. So much for Maytag dependability.

We purchased our Maytag Bravos XL last month and within two weeks, we were noticing a BAD odor every time we used the machine. In fact, I just walked back into our house from outside and the entire house smells like old dirty dishwater and the smell is coming from the laundry room! This is a very expensive washing machine and we bought it because we thought that a Maytag would be better than the Whirlpool that just died after many years of repairs and aggravation. After reading these reviews, I wish I had bought a Speed Queen.

I bought a brand new Maytag washer and dryer at Home Depot and did not use until a week later when I found out that the washer did not spin out the water and the machine turned off automatically when cycle was not finished. As a result my load was soaking wet. I called Maytag customer service and they sent the technician. I was standing next to the technician to see what was wrong with the washer. After checking several things and seeing the unresponsive of the washer the technician told me the control unit failed and the clutch also failed. He had to order the parts and it will take at least a week for him to come back and fix it.I called Maytag customer services and complained about the brand new washer and ask them to replace it with a new one as I dont know if the problems returns and it doesnt have just one failing part. Both the controlling unit and the clutch were failed. Also i bought a brand new products I expect it to work. I dont want to pay for brand new washer and I could not use it plus it took so much of my time going back and forth between Home Depot and Maytag. It was so stressful and I had tons of laundry that need to be done. I also had to take half a day off to call the Maytag customer services and Home Depot.During my first call with Maytag customer services I asked them to call my local Home Depot so Home Depot will allow me to exchange for another Maytag washer. They had refused at first but when I told them all the reasons above they agreed to call Home Depot and allow the replacement. They asked to hang on the phone while they were calling Home Depot and finally confirmed with me that I could go there and do the replacement.Surprisingly when I came to Home Depot they said they did not get any notes or call from Maytag regarding my PO# and the replacement. I had to wait for 1hr and 15 minutes for the Home Depot to be able to connect to Maytag customer services and we had to wait for their supervisor to approve the replacement. I was so disappointed later to hear Maytag supervisor telling Home Depot that I had to wait for the repair and they did not approve the replacement. Its really a waste of time and money to buy Maytag products and they dont honor what they said to customers. Once you pay them they take your money and dont really care whether their product is worth the money consumers spend on them. In general its a rip-off!!! Stay away from Maytag products if you dont want to waste your time and money!!

Wish there was some way to secure all dishwasher under the cabinets better. It tips forward slightly, but gets caught on counter top, so it won’t fall over. The dishwasher itself is truly amazing. I love the stainless steel inside. I ensure I use the dishwasher cleaner on hottest cycle once a month. I have no odors. Both racks hold up well and the silverware tray has never given me any problems. I even like the thin little third top rack, which is where I lay my larger flat knives or spatula. As long as I use the finish dishwasher cleaner, the dishes come out sparkling. And a few times I have forgotten to fill the finish container, the dishes still sparkle. My teenagers do the dishes a few times a week. They don’t wash them off ahead of time. On occasion I have to pick a few pieces of corn or food out of the bottom, but the dishes still sparkle and the leftover food caught on the drain, well it looks clean enough to eat. I would definitely buy it again.

In August my GE refrigerator of 22 years bit the dust. Went to our local appliance center and purchased this unit for $2100. Have only had it a month and am so dissatisfied with the water dispenser, ice machine and doors, I want to return it. I cant wait for all the other things to go wrong with it. I dont know who the engineer was behind this but he needs to be fired. I really wish I had reviewed this refrigerator before purchasing it as I will never recommend Maytag again after reading all the bad reviews. The name Maytag used to mean something dependable and made well... Rant over.

Same issue as everyone else. After about 15 months the control panel on my Maytag dishwasher model#MDBH979SAM1 has malfunctioned. First it would only let me choose the rinse option but now all the lights are turning on and the dishwasher will not stop washing but yet the dishes are still dirty. I called Maytag and they quoted me 249.00 to fix the issue. But if its a common problem with this make and model why do I have to pay to replace the panel. They should recall this model or replace the panel with an updated one that wont have the same issues! I cant imagine paying 249.99 every year to replace this panel that seems to malfunction no matter what you do!!! I paid around 550.00 at the home Depot for this dishwasher! It did not even last me two years!!! I want a lawsuit filed against this company and I want my money back or my dishwasher replaced with one that works and wont have the same issues!!!

I purchased the Bravos XL washer and dryer combo 2 years ago. Dryer is fine, but washer was EXTREMELY noisy from day 1 and has gone downhill since. It would leak during spin cycle and frequently stop due to unbalanced load, refill and stop again. Now it wont spin at all! We have checked to make sure it is level, it is. I live in a very rural area and its very difficult to get repairmen to come out. This is my first and last Maytag for me.

Belt broke in inside under tub after 13 months $150. Now another year and I am getting an error message F51 and it stops washing. Im done. Old Maytag lasted 14 years. This is done in 2. Im not paying any more to have it fixed for whatever F51 is. Im cutting my losses now. Hate this machine the way it washes anyway. Always feel like its gonna take off for Mars to join Matt Damon. HA. I try to laugh to stop being mad. Dont buy these. It gets no stars. And after reading other reviews, it deserves none. Shame on this company! Ugh, its making me put a star rating. But I say none.

I bought our Maytag HE washer model #MVWC565FW back in July 2019 after having owned a Kenmore scratch and dent washer from Sears for approx 25 years, and in just one month of using it I knew it was a mistake. There are only 2 water levels - deep water (full tub) or practically no water (though there are a number of settings, there is no difference in water level, its just full drum or very very little water). The auto-sensor water level option is a joke - there is barely enough water to wash anything - its like going back hundreds of years to washing and beating your clothes on rocks. Items in the washer become so tangled it sometimes takes a while to detangle before placing in the dryer. Water stops filling the tub when lid is open - I can no longer wash and rinse delicates while the drum is filling. It took 3 calls w/ Customer Service to get an ADDITIONAL lid latch that I can use to trick the machine to thinking the lid is closed - I keep the actual lid open, then stick in the lid latch I bought - take it out when Im done hand rinsing. This also enabled to to view the washing in action - IT DOES NOTHING! Clothes stay in the same place as you placed them in the tub - they dont move, they dont wash - and I bought a washer with an agitator - that is in quotes because it is a misnomer with this brand! The wash cycles ARE SO LONG it takes all day to wash a few loads of laundry. Once you select a setting YOU CANNOT CHANGE IT - the washer empties and stops, then you have to start all over again - ENERGY AND WATER EFFICIENT...REALLY???? What a bunch of you know what! This is the most inflexible piece of junk I have ever had the displeasure of owning. I have to keep jugs of water on hand that I keep filling up to at least have a bit of water. When I called Cust. Svc. at the beginning telling them my experience - the person on the phone had nothing to contribute - they couldnt even tell me what cycles might fit my needs - they told me to go back to Home Depot and ask someone there! WORST APPLIANCE WORST COMPANY.

The machine started having issues within a week of purchase. The current issue is, when running the clean cycle, the washer becomes stuck in a mode where it is constantly adding and duping water down the drain. First time it happened, I started the clean cycle before going to bed. In the morning the machine was still in the clean cycle. Running water in the tub and pumping back out down the drain. The water heater ran all night, as the washer was filling and draining the tub at the same time. Each time we attempt run the clean cycle, the washer locks up in this mode.This is the only issue I have had. Many people complain about wrinkled clothes and I agree. I take each garment out the washer and shake it out before putting it in the dryer, this makes a huge difference. Just remember, this is not your mothers washer. It does a great job at cleaning the clothes and saves many gallons of water a month.

Purchased this unit back in November 2011. Sometime this year it started leaking water just like many others from the freezer unit onto the floor (many times large puddles). Im tired of the permanent towel on the floor to absorb the water to prevent a potential slipping hazard. I too went online and found a very nice video on youtube which showed how to disassemble the freezer compartment. Took everything apart and noticed that there was water frozen on the supply line. Melted this and put everything back together, for about a week there was no water leaking so I figured all was well. About a week later the puddle was back so I sent an inquiry to Maytag and let them know I had an image of the issue and asked if it was covered through manufacture warranty. Here is their response: Your email is extremely important to us here at the Customer experience Center and we sincerely apologize for any delays in responding to your email. We are working diligently to respond over the telephone and through email to all of our customers. We are sorry to learn of the problem you are experiencing with water leaking from the bottom of the freezer. Unfortunately, we are unable to determine from this location the exact cause of the problem. We recommend that you contact a certified technician for an accurate diagnosis. Once the problem has been diagnosed, please contact us back so that we can review the concern further to determine if assistance is available. For your convenience, we have provided below service providers in your area that you may contact for service. Aries Appliance Service (925)367-7708, Vigil Appliance Service (925)371-7701. You are a valued customer and we do apologize for any inconvenience this concern has caused. We invite you to contact Maytag again either by calling (800) 344-1274 between 8:00am to 8:00pm EST weekdays or by emailing whenever the need arises. When calling please press the available option or stay on the line to reach a representative.Frustrated I went online and found this forum where hundreds of other people had the same issue and that many of them were resolved by the new P Trap. So I watched another video by the same guy on youtube that showed how to replace the P Trap. I went online and found the replacement P Trap Manufacturer model # w10619951. One of the comments there actually said to call Maytag first as they were able to get a replacement P Trap for free. I believe if it was under a year old they would also pay for the labor to have it replaced. So this morning I called Maytag, the first guy Jim said I would have to have a certified Tech come out (76 dollar service fee, plus whatever the labor would cost) and Maytag would cover the cost of the part. I asked Jim if he could just send me the part and Ill do it myself, he reassured me that he could NOT do this and that the system was very specific. I told him I did not understand that a bad design and known quality defect, why should I have to pay several hundred dollars to fix? He told me that was the way it is. I asked to speak to his supervisor and put me on hold. Not only was the hold music extremely obnoxious but there was a loud humming noise as well, I waited for 10 minutes hung up and called back. I spoke with Maggie this time. I told her I wanted the part sent to me and if she couldnt help me I wanted to speak to a manager. She said she did not have the authority to ship me the part without approval. She said she could ask for approval and after waiting for about 3 minutes she came back on the line and said she spoke with her supervisor and that they would be sending me the replacement P trap today via FedEx. Had they not sent me the part my next stop was going to be the better business bureau..

I suppose I am the lucky one in that the Maytag Bravos was given to me free. I took out a perfectly good Maytag standard agitator washing machine and replaced it with this several years old unit. What a mistake! I read the other reviews and see that I share the same problems. I always get a the oL fault as soon as it goes to do the final spin. So I have to reset and try again. Also I have seen the same kind of dirt on the clothing as others report. I dont know that I will waste my time contacting anyone about the fault code. I may just put the old one back in and scrap this thing!

I have now owned my highly efficient and low-cost to operate washing machine for 6 years. It is a top loader and uses HC detergents.This means the washer needs minimal soap to clean the clothes. I especially appreciate the different types of loads such as deep cleaning or regular cleaning. The washer has sensors that evaluate the size of the load and thus only utilize the amount of water necessary. I really like the quietness and being able to get the very best wash because the washer does exactly what it needs to do. It has more than been the appliance that I had hoped for. Love it! It maintains itself.

Bought the Model MZD2766GEW and the MSD2454GRW side by side models of the Maytag side by side and the wide side by side from Home Depot in the year 2002 replacement appliances after a fire. For both units I paid $2526.92 dollars plus tax to put one in my kitchen and one in my basement. I was told by a plumber Maytag was the best, buy Maytag. It seems like from day one things went wrong. The ice maker kept building ice in the bottom of both freezers. The ice maker never worked right and would build up so much ice in the dispensing area, you would open the door and ice would fall all over the floor and you would have to take a knife to the shoot of the ice maker to unclog it. The drawers would freeze, the vegetables and anything in them, you had to keep the refrigerator temp to Zero and things would still freeze. Water eventually would leak all over the floor and I couldnt figure out where it was coming from. The freezers on the left but then water seem to be running to the right and out the refrigerator part. I couldnt afford to call anybody and the warranty was running out. I had 2 year parts and one year labor but at the time couldnt afford the service call charge. Eventually I was sent a recall notice for a compressor or such. I thought, Hurray, It will be fixed. Not at all. He replaced both those parts on both refrigerators and after he left it started leaking again. I called Maytag and they said, did he replace the part that was recalled? I said yes and they said They were not obligated to pay for anything past the recall. I should call and have the units serviced by a technician at my cost. If he says its the recall piece again, to call them back. Again I had no money to call a technician right away but when I did, he came to the house, told me it wasnt the recall and claimed to fix some kind of defrost sensor which cost $180.00 for the parts plus labor, plus service call and this had been a different technician than the first. He left and the problem continued to leak, freeze etc. In fact it seemed worse. I gave up calling and decided to deal with it hoping one day to replace but money problems happen and it is now 2014 I never could afford new refrigerators and have had to put up with the leak for all these years and continue to pick up and replace soaked towels everyday. In 2005 I disabled the ice maker which helped when I opened the door since ice doesnt fall out but both Refrigerators continue to make thick sheets of ice on the bottom and food is frozen into it so I cant use the bottom and when the buildup gets so bad it takes 2 days to defrost by shutting the entire unit off. All I can do is put my food in one freezer and refrigerator while the other defrosts. I also have turned the downstairs one off completely. Now as a second refrigerator I just dont trust keeping it on leaking also. I bought these units after a whole house fire and the last thing I want is another fire because Maytag just doesnt care but I cant afford new Refrigerators because these repairman and Maytag cant figure out whats wrong and fix the problem with this dangerous feature and I call it that because it seems to come with most of their units from when I bought the unit till now.12 years later people are still having the same problem with the same and copy cat units. Maytag, a plea goes out to you to recall and repair these units. The original recall did not work and like me a lot of people need to be redeemed for what you left go on and a lot of repairmen are ripping off people calling this problem what its not and stealing our money when you know what the problem is and can fix it. My plea is recall this problem or be responsible before God or who you believe in for letting it go on so long and the damage it may cost people. Maytag, people use to love you but youve ripped our hearts out and it will cost you in the long run.

I just purchased this washer in Feb. 2012. The motor had gone out in Oct. I called Maytag Service, they came out to repair it. In Nov., it was doing the same thing again. I called Maytag Service, and they sent someone out to fix it. They expected me to take off from work where they inconvenience me with this washer. It is a reject washer. They would give me another washer and not consider people having to work and cant take off for their reject washer. They said as long as it is under warranty. I feel that I should be able to get me another. This washer has given me problems since I had it.

My Maytag dishwasher Model No. MDB7759AWS1 caught on fire last night, inside the control panel on the top of the door. This was very alarming as it filled the house with smoke and caused some fire damage on the bottom of the countertop also. This could have easily caused a house fire and is very disturbing. When I called Maytag, they say this model is not recalled. In my opinion it needs to be. This is a huge accident waiting to happen in other peoples homes. Please beware. If the countertop would have caught on fire entirely, the house would have gone up in flames.

A refrigerator has to keep your food at constant temperature. The first Maytag refrigerator I purchased from Home Depot could not get cold. I mean the refrigerator never got below 65 degrees. I called Maytag and they played dumb. Just wait weeks for a repairman to check a brand new product that is not working. Home Depot replaced it in few days with another refrigerator of the same model. It runs but doesnt get really cold (it only has a fan in the freezer and the air comes down from the freezer to cool the refrigerator). I live with it because all you will get out of Maytag/Whirlpool is to turn the dial to a colder temp. A little over a year passes and the fan in the freezer just stops running. I called a local certified service person. He looks at the fan and says that its running but barely. I had to replace the motor at cost with labor of around 200 dollars. I kept the motor. Turns out the motor is made by Panasonic. The current replacement motor is made in Mexico. Now the refrigerator runs cold. Since I had two of these refrigerators that failed to get/stay cold, I think they got a bad batch of motors. Maytag response was to refuse to pay a dime, it is outside of the warranty - even though I had called about the refrigerator not getting real cold on the second refrigerator. So basically I lived with food being kept at a way too high of temp causing spoilage for a year and Maytag/Whirlpool could care less, they are only worried about their bottom line.That is not the only problem with their product. The drain pan grows a mold that looks like pudding. The only way to clean it is to pull the refrigerator out, take off the motor area cover (which is really cheap cardboard) and clean it out with a rag. There is no way to remove the pan. The compressor is mounted so low that it heats up the floor. I have concrete floors thus I have no fire risk but if you have wood floors, I would check the heat level. It is nearly impossible to clean the dust off the fins on the refrigerator coolant lines. The back of the freezer door shelves are metal and very sharp on the back. Thus if you stick your hand in to pick something up, you will get a nasty cut.I have owned only Maytag, Whirlpool and Amana products my entire life. I will never purchase their products again. They may pretend that you are buying an American product (they use the American flag) but this product is nothing but OEM garbage made by the lowest bidder. They try to sell you an extended warranty for around 300 bucks for an addition 3 years. I figured if the fridge went bad after 3 years, I would just buy a new one. I never expected a motor to fail less than a year (I would say it started going bad about 6 months into ownership as started making ice at a lower rate). Maytag refuses to stand behind their products. When I told them I had the motor that failed, they had no interest in even looking at it. Do not waste your money on their products. I also own a Maytag washer that is the worst washer I have ever owned.

Fifteen months after purchase of the top load washer, we have had to call in repair. The lid lock and sensor have went out on the machine and the repair costs are equal to the purchase of the machine. Whether the consumer has an extended warranty or not, this is unreasonable. So hear this Maytag, the CONSUMERS will invest elsewhere when delivered cheap merchandise like this even if it is Made in the USA as you wish to tout in order to bait the consumer for their money instead of providing superior quality American products. This consumer is sending this machine out the door.

I have a Maytag Washer and Dryer that I am very happy with. I have had both of them for about 6 years. I had a problem with the soap dispenser not working properly shortly after I purchased them, but a service technician came and fixed that within a few day. I will probably stick with the same brand when/if I do have to replace them.

Bravos washer, a year old machine, needs new main electronics board $220.00 plus $125.00 labor to install. Repair guy said humidity makes them go out. Go figure a part sensitive to dampness on a wash machine. Why don’t they seal it better? By the way, this machine does not wash, worth a crap. I am getting something new.

I bought my Maytag Centennial washer & dryer about 2 yrs ago. It wasnt long after I bought the set, that the washer started having problems. I noticed the button to turn it on wouldnt go off. Then it was a pain in the ** to not be able to open the lid while the water was filling up. Something I havent noticed until today, its suppose to fill up to the amount of clothes that is in the washing machine. Well when I opened the lid there wasnt enough water in there to even cover all the clothes. Now I know why my clothes are not coming out clean!!! I am so frustrated with this machine and the company!!! DO NOT BUY THIS PRODUCT!!!!!

I have a Maytag purchased about a year ago. My old Maytag lasted 16 years. The salesman told us that they are now built to last 8 years. It’s pretty noisy, so much so that I have to close the door to the utility room. I guess it gets the clothes clean but it used very little water. Fortunately my model has an agitator but nothing like the old kind. After looking at many models, I feel this was the best choice for the value. It is top loading which I like.

We have owned this range for a little over a year. Oven will not hold correct heat. Have temperature sensor replaced under warranty. Did not make any difference. You can adjust temperature up or down according to actual temperature readings, but the temperature swings so much that it is worthless to try. Very hard to get food baked right.

We bought this dishwasher on 7/8/2013 which is my wifes birthday and boy was that a mistake in many ways! I had 5 service calls on my Maytag Dishwasher MDB7749SBM1 before it went out of warranty. It has issues with the ribbon cable and controller and the control lights are like a disco on the keypad. Now it gets so hot I cant touch the door when its running. So I have had to turn off the power and go get a new dishwasher next weekend which WILL NOT be a Maytag!

When I went to whip down the small shelve under the knobs, I cut my finger on the sharp metal. Was told that is the oven vent. Checked out your instruction book and found NO mention on that being a danger and to take care when cleaning. If I had been informed of that sharp metal piece I dont think I would have looked at your stove. The metal has razor sharp edges on both sides making it almost impossible to get too close to cleaning it. That shelf is a nice place to collect dust, grease and food boil overs and now I have to be extremely careful about cleaning. Thanks to someones not thinking in their designing. The stove is what I wanted other than that one fault.

You cannot go wrong with Maytag, even if there were issues they are reliable in repair, and parts are available so you arent forced to purchase new like some technology. I have been pleased with the front load washer dryer since 1998.

Maytags reputation for quality is gone. Our Neptune washer has had mold, door lock seized up and wouldnt open, and now our dryer drum is cracked. Exaggerating your products reliability is one thing - this borders on corporate fraud.

Bought Maytag dryer in December 2016. Worked fine for first 3 months. Then blue coloring showed up on back of drum and came off on white clothing. Had tech come out. He took pics and send to Maytag. They said it was normal. Further talks with customer service brought statements that we caused problem by drying blue jeans. Funny we never had. They just continued to say this discoloration was normal and we did something to cause problem and nothing they could do. But at least they were sorry for our problem. Whirlpool does not stand behind products. Dont buy.

I just had an astonishing phone call with Maytag customer service (1-800-344-1274). My mind is boggled; my tongue is tied. Only Consumeraffairs.com can offer relief from the bleak, solitary misery engendered by this disorienting encounter. I called Maytag to seek information regarding the number of gallons used by any of the wash cycles of the Maytag BRAVOS series 300 (Model: MVWB450WQ2). I live in California, and like millions of others, Im curious as to what the maximum amount of water used per wash might be. I told the customer service agent that Id be happy with an estimate of any parameter: the maximum water demand for any cycle, the minimum, the average any ballpark estimate would be great! My goal is to change in a meaningful way our weekly water use. How much does it matter if I do my familys laundry once vs. twice per week? Is it any more water-efficient to run one large load vs. two small ones? The Customer Service agents would offer only a scripted response to my query. Could they tell me the minimum or maximum amount of water used (on average) by any of the cycles? Any cycle any condition, just an estimate, please. A universal it depends was all I could extract.The scripted answer? The amount of water used depends on the sensor and the exact conditions. Well, yes, of course; I dont expect a specific amount. Just as the amount of gas used by a car depends on the length of a trip and the speed driven, the amount of water used per cycle will vary, but nevertheless we know, more or less, how much gas is used by a Toyota Camry on a trip between New York and the Maytag Customer Service office in Benton Harbor, Michigan. I noted that, if Maytag claims to build high efficiency (HE) machines, then they must be HE in comparison to something, right? -- otherwise how could they claim that these machines used less water? Less than... what?** insisted that no one at Maytag could tell me the answer. He asked, What reason could Maytag have not to disclose this information? I know this isnt the answer you want to hear, but its simply not available. Not even a range of water use per cycle required/solicited/demanded by the sensor? Can Maytags engineers be so indifferent that they never tested any cycle for its water use, but instead they just imagine that, by virtue of its mysterious sensor, it was lower than the use by their non-efficient machines? Your help in getting to the bottom of what felt like an act of stonewalling would be highly appreciated!

Purchased our Maytag Centennial Washer Model MVWC400XW4 2 years and 5 months ago; guess we are luckier than most; it has now failed in the spin cycle, high pitch, high volume whine, sounds like it is about to explode. Needless to say is out of warranty; and too expensive on our limited income to have a technician repair. I will hope to make the repairs myself; nothing to lose at this point; and from reading the countless negative reviews about this product; should be as many countless repair suggestions on YouTube. Obviously if Maytag would stand behind/up for their product as they claim they do; I and many others would not have these issues. My wife and I for sure will never buy another Maytag product until Maytag resolves the issue, which if my calculations are correct will be never. My advice is simple, do not buy Maytag products.

Had a Maytag washer, 3.5 tub, stopped working. The motor upper bearing lost it press, drive shaft dropped 3/4 inch and locked against lower housing, stripped out pump spline. No f/u by Maytag after many attempts. This is a design flaw, the upper housing is so thin, if it had .001 press on it I would be surprised. This flaw resulted in a cascade failure of motor and pump.

We purchased a top of the line, state of the art Maytag washer and dryer Neptune. The fill valve failed twice, flooding the first floor and the big storage room below. Thank God we were here! Now the thing halts mid-cycle and wont continue. The repairmen both said the design is messed up and they hate to work on the Neptunes.

We purchased our Maytag fridge on May 13, 2013. On June 19, 2013, it stopped working. We called Home Depot where we bought the fridge and they told us that we would have to deal with Maytag. What a nightmare. The repair guy came out and ordered a compressor for the fridge. 2 days later, when the compressor came in, the repair guy told us that the fridge was unrepairable. Great, what was I supposed to do with this hunk of metal now? I called Home Depot back, and they ordered me a new fridge, added a five-year warranty for free, and the Store Manager even dropped off a small dorm size fridge for us till our new one came in. Yeah for Home Depot!!!! I would recommend no one ever buy a Maytag product again - what a piece of junk. Their customer service didnt even care; they had the same old story - We will get back with you in 72 hours. Maytag was good when it was built in the US; now its just more China Junk.

Bravos x - Ok so I was checking on my washing machine balance which is off. I came across the reviews and find how horrible the machine is! Grinding at last cycle, and not wringing out clothes on some loads. I thought grinding and wringing out was to be that way since it did it from day one. I thought I just needed to adjust clothes to wring out. Balance was taking out some clothes but it was put in properly. Boy was I wrong. Im so pissed after reading all your reviews. Im going to contact my daughters who works for attorneys about false advertisement and selling something they know is crap.

Ice builds bottom of freezer then leaks onto floor. Should be a recall.

Got woken up to the sound of my refrigerator ice lid flapping. Boy is it loud! Called Maytag and found out it was a recall so they will fix. They set up for someone to come out to fix the following week. That was a flop because they did not have the part. I waited 4 hours for someone to show to find out that Maytag scheduled the appointment for nothing - not only did they NOT have the part but they did not have a clue as to when it will come in. Time is valuable! Here we are 5 weeks later and my refrigerator is still flapping and loud. Has been calling Maytag for them to say that the part has been expedited. Well it has been expedited for more than 3 weeks now! Today they say that it will be another month before the part comes in! Not Good! This is such an inconvenience and Ive lost a lot of sleep over this flapping noise. Its an embarrassment when guests come over to our home! Tired of it!

I am retired and have always had dogs in my life. My recent purchase of a new Maytag top loading washer has been very frustrating. There is barely enough water to measure in an oversize tub. The placard on the lid, and in the owner manual clearly show three levels of water. Each load takes twice the time as I am used to with my older Kenmore washer. I am forced to cut my loads in two or three, and use more water and energy to do a job that used to take less than half the time, water and electricity. I have had warranty repair to replace the control board twice, but nothing has changed. The repair techs both said there is one program on new washers, the knobs and settings do nothing, and recommended I get used to it. They explained the EPA is responsible for all changes to Protect consumers from harm. WHAT???I wish I had never bought this unit - if I could get my Kenmore back I would, in a hot minute! What a waste of a large tub to properly wash pet bedding and bedspreads/pillows, when there is only 3-4 inches of water! I wasted an entire paycheck, when I could have gotten my other unit repaired or rebuilt. I am seriously frustrated, I am searching for an older washer unit to get back to doing my laundry without being forced into a laundromat for pet bedding and larger items!!!

I purchased one of the first Impeller washer and dryer. The dryer is great, but the washer needed repair immediately. Home Depot refused to exchange the pair, so I will never buy from them again. The washer takes over an hour to complete the wash cycle, has to be set on Bulk in order to get enough water for a decent wash, and is extremely rough on clothing. Its made holes in some of my shirts and everything comes out twisted without enough rinsing. Sleeves are always turned inside out. Thats how rough it is. It costs me more in water and electricity. Neither Home Depot nor Maytag would replace the pair for me.

I bought a new washer and dryer on Sept. 9, 2011. Front Load Commercial 2000 Series. I have had Lowes to my home 2 times since it was delivered because it shimmies across the floor. I am very upset with the purchase of the Maytag front load washer. If you could please get back to me on what can be done. I would like for a representative to contact me and come and look at the situation.

I was pleasantly surprised that this basic model would work so great! It really gets the dishes clean. It came with the house so I did not choose it and probably would not have bought it if I had to shop for it.

We purchased the HE commercial brand for our family of 7. It has been running mostly fine for about 2 1/2 years. It started making a horrible grinding noise about 3 months ago. It was getting worse and worse. I decided to google the issue and discovered there was a common problem with a nut falling off the bottom. I leaned the washer back and found the nut on the floor, right below the center of the pulley. I reattached it by removing the pulley guard which had been getting cut by the loose and wobbly pulley, put some superglue on the nut and reattached it to the bottom. NO MORE NOISE!! Im willing to bet that this has caused slippage of the pulley, poor performance and many other issues. Maytag should do something about it.

I purchased this dishwasher from Sears in July of 2013. Barely 3 years ago. The last few months the controls have been acting odd. The control lock would automatically just turn on at odd times. Yesterday when I hit normal cycle it went to a different cycle and had many other options lit. It would not start. Finally it went dark, no lights, no nothing. I see many people have had these types of issues with this type of Maytag dishwasher. Disappointing. A dishwasher should last longer than 3 years. Sears said they would send a repairman out but it would have been minimum $200 after it was all said and done. Id rather own a non-Maytag dishwasher so we went and bought a different brand.

On 7/8/11, the non-freezer part of the refrigerator failed to cool to needed temperature. This fridge is model MI TXEMMWWOO, with serial no EY4705715, purchased on 7/13/10 at Home Depot.We contacted Maytag and were told to wait until Monday. On Monday, we were told that a serviceman would be out on Thursday, the 14th. On Wednesday, the 13th, the serviceman called to inform us that he would come the next day and that he would have to collect for the call. Since the fridge was still under warranty, we demurred.We went to Home Depot for advice. They called Maytag, and after an hour of getting the runaround, we were told that the serviceman would come on the 19th and that the call would be covered by the warranty.On the 18th, the serviceman called with the same message as before: he would have to collect the charges for the service call. Another trip to Home Depot led to the advice to activate the extended warranty at this point.Under the extended warranty, the serviceman came on the 21st, had to order a new part, and finally installed the new part on the 29th, three weeks after the misery began, and after spoiled foods, many bags of ice, and great inconvenience.We have other Maytag appliances, but this purchase has been a cruel lesson in Maytags lack of product quality, deceptive warranty practice, and indifference to consumer satisfaction.

This Maytag Bravos is the worst washing machine I have ever had. Who ever heard of washing with almost no water? Takes way too long. Clothes not clean. Any water savings way offset by ridiculous length of washing time. I can wash and dry a load of clothes in an old stacking washer/dryer before one finishes washing in this thing. I was excited to get it and now cant wait for it to go. Wont make this mistake again.

Purchased a Bravo set 5 years ago. Paid $730. For the washer. 4 repairs in 5 years. It is now has a bearing out and that will cost $450. MAYTAG used to be the best... buyer beware!

Failure to drain after 3 years. Was disappointing so repairman fixed problem, a fuse, in 3 minutes but charged $300! Since then I make my own repairs and have had no problems that I can complain about. Both Maytag Neptune drier and washer have worked well. Buzzer just failed.

Maytag Bravos Washer 300 Quiet Series Model MVWB700VQ0 - Nothing about it is quiet. Worked pretty well the first year. Spin cycle works too well. It twists and rips. The second year it needed a new pump because a dime got into it and cracked the pump. When you wash anything bulky you better sit and watch it because it will almost certainly go off balance. Year three Sd (suds or slow) code started flashing and washer stopped half way through. Not sure why suds because I only use HE Tide, no perfumes or dyes due to my daughters sensitivity. I use Affresh as directed and on schedule. Was told it was a slow drain, found two dimes in the filter and a lot of lint. Still not working and flashing Sd... stops half way, agitator moves left to right doesnt spin. When the diagnostic was performed, the basket spun but when it stopped it made a grinding noise. Now it might be that it needs new bearings! So much for the Maytag reputation. Its junk and I will not be buying another Maytag, Whirlpool, Kenmore or any other product from their affiliates. Not purchasing anything from Sears again either. Also I will be canceling my subscription to Consumer Reports because they highly recommended this product. Shame on Maytag. How do we start a class action suit?

I have a French door fridge Maytag like everyone else. The bottom freezes over and I have to de-ice it. Now the freezer doesnt want to cool. Its 3 years old. Total piece of junk.

2013 We purchased from Lowes Maytag washer and dryer front load stackable. We live in a house 1890. We have a closet that these units go into so we are restricted to what brand we can buy. WE read the reviews. People must lie or are paid to write good ones. Within a few weeks the washer was giving us trouble. The door latch was not closing properly and it would take up to 20-30 min. to get it to start. Called and they said the latch was stuck. Again started having problems on and off. Months went by and had another service call. Same issue. Fixed it again. 2014 again same problem. We have to order a new latch and some other part. They could not get the part. Called Maytag directly and they were back ordered. What does that tell you. This is a major problem so much so that no one anywhere had the parts. 6 wks to finally get it and got it fixed. But in the meantime, the dryer was not working correctly. The clothes were damp and lint was all over. It was like a steam bath. They came out and when they looked at the back of the dryer it was burnt. Now this is what upset me. He said it could have caught fire and burnt down our house. Nice. The dryer was shot. They said to fix it would cost more than it was worth. Our warranty gave us a new dryer. 3 wks later I have my washer and dryer back working. In the meantime we have spent more time at the laundromat than at home. Brand new washer and dryer and are going to the laundromat. We had the dryer 5 days before it stopped working. Brand new dryer. Called and got a service call. The spring on the start button was not correctly put in. Who inspects these products. This was not right from the factory. So they fix it. Said if it happened again they would need to replace the entire thing. I do not know what that means. That was Dec. End of Dec. the washing machine is not running through the cycle. It had weird display on the washer. Thought maybe it was overloaded. Had to cancel and drain and then hit drain and spin. This takes not only more time but more electricity. I put in 2 sheets and it did it again. Had a few loads that ran properly and again it started. Called for service. He comes out and the motor that runs the belt to spin and some circuit board is shot. They call 2 days later and say that no parts can be found anywhere. WTH! It is 18 mos old and already the parts are extinct. So the warranty company said it was not worth fixing. They are giving us a new washer.I remember the commercials about Maytag that the repairmen had nothing to do. Well I thought it was because they did not break down. No... they cannot find parts. This is unacceptable. We have to go through the inconvenience of them not working and schlepping to the laundromat baskets of clothes. In the winter this is not fun. We are retired. Have to walk down icy steps. I have a washer/dryer upstairs and I cannot use them. Dont work. Not just the aggravation of dealing with repairs but not getting parts available, then having to wait to get money back to order a new washer and dryer and then get the dryer and 5 days later it doesnt work. Now we have to wait 2 wks for a new washer. It better work. Have to buy the warranty over again on each product cause they fulfill it when they buy you a new product. So this costs us extra money. The money we pay at the laundromat. The cost of electricity every time we have to run the washer 3-4 times to get it to spin out the water so I can dry them.To say I am upset is an understatement. I was told by a rep at Lowes, well Maytag has about 3 lemons a yr and you just got all of them. That was their consolation to our problem. I think Maytag needs to inspect their product. Our house could have burnt down. It is not a matter of parts going bad but damn the stuff is not even 2 yrs old. And the dryer was 5 days old when it stopped working. WE had a Maytag dishwasher and it was installed brand new and did not work. It had a defect in it. I never got to wash one dish in it and it had to be repaired. So I am not happy with Maytag. You go on Facebook and tell your story and all the Maytag horror stories come out. You need to do something to save yourself. Your company name is going down the tubes. Thought you should know this.

I have a 26 cu. ft. side by side Model MZD2665HES, like most folks in my neighborhood (spec homes). The icemaker died and service was called. They looked at solenoid, and replaced the ice maker assembly as a wag that it was the problem.. still no ice, but the water was still able to be called. I replaced filter- still water only, no ice. Little did we know it was the filler tube blocked with ice, and the service man didnt once suggest turning off the water service. SO, every time water was called to either make ice or to fill a cup with, it put intense pressure on the point of assembly where the water line comes into the fridge (water inlet tube). A pin hole developed in the little plastic bit (water inlet tube plate) and every time the water was called to ice, guess what happened - it shot right out the back on drywall.Almost $20,000 dollars worth of damage to wood floor (warped), drywall (jello), and flooring (carpet) ensued. Mold was all over and had to be contained and treated for days to be fixed. Im still duking it out with service repairman and insurance companies. My advise: If you have this fridge or anything like it and the ice maker stops working, IMMEDIATELY shut down the water supply, turn the fridge off and check the filler tube in the back for ice blockage. Probably a good idea to pull the fridge forward once in a while and check the back for water also.

I bought Washer and Dryer Pair new less than 2 years ago. Within 6 months of purchase, the bearing went - warranty. Then 1 week before one year old, bearing went again. I contacted Maytag. They told me it was my problem and I should have bought extended warranty. Lemon law should apply and I asked about appeal process and was told that there is no such thing. Now, the washer is needing a new pump and it is not even 2 years old!

Refrigerator - The freezer of the refrigerator would randomly leak on the floor. When I had it repaired on 12/30/14, at a cost of $253.97, the repairman showed me the defective part. He confirmed the online reports that the leaking was caused by a defective part. The defective part had been used because it was cheaper. Now the repaired refrigerator works well. Last month, the control panel on the dishwasher stopped working. According to the online reviews, this is a frequent problem requiring that a new control board be installed. The reported failure typically occurs after the one year warranty expires. My appliances are located in a second home so are only used about once a month. A salesperson at a different appliance store said that appliances usually last from 10 to 12 years. The four years of occasional use prior to failure is not acceptable. I would like to have Maytag repair the dishwasher at their cost. How do I get this to occur?

For families where people work in gardens, work on vehicles and get just plain dirty doing things anywhere outdoors these agitator-less machines are not for you or me. Ive had mine for two years and I truly dislike it (Model MVWC425BW1). With different products I scrub dirt and grease stains on pants before they are put into the washer, scrub again when they come out of the wash and then scrub and wash again a few more times but I cannot get all the dirt out. I now work more on laundry and harder since I got this machine.This agitator-less machine is designed for people who dont get really dirty - just remove everyday perspiration and household grime. I think this machine was designed by engineers who have never done daily laundry for any length of time and theoretically thought it would clean really dirty clothes. They were really wrong! Having done laundry for 50 years, I now know that an agitator cleans better. It would be nice if other women and I, who have done laundry for years, could be on focus groups about developing new washing machines.

If I could rate it lower than 1 star, I would. We bought ours new in 2005. Within 6 months, the main pulley for spinning the drum fell off not once but thrice. The repair tech said that the shaft was machined incorrectly at the factory and the bolt that would normally hold it on was backing out. The 3rd time it happened was close to the end of the warranty and the tech could not make it out before the warranty date. When he did show up, they wanted to charge us. I wound up putting the part in myself. Two months later, the suds alarm came on, which caused the water valve to open. The pump kicked out and the water valve stayed on flooding my basement and the electronics in the washer. This happened twice. The second time was a week ago and I tossed the ** out to the curb. We also have a Maytag Gemini double stove which does not work either. This is the second and last Maytag appliance that I will ever own. They are junk!

I purchased my Bravos (ecoconserve) washing machine in 8/2013 from hhgreg. The problem I have is this grinding noise with the spin cycle. So I unplug the machine because the lock lid light is flashing and wont unlock unless I unplug the machine. I grew up on Maytag so that was the reason I purchased this machine but never again. I am so disappointed in this product. :(

This fridge is a piece of crap. Bought brand new and right after warranty the freezer started freezing up and leaking all over the floor, ruined the wall behind the fridge which created mold as well as the puddle on the floor that multiple people in my home slipped and fell and it started shocking anyone who touches it. Called a repair man he says he doesnt know why its shocking probably is the manufacturers fault as well as the defect causing it to freeze up and leak. I call Maytag and the guy doesnt seem to care that my 7 year old has been shocked and says unplug it and I will just need a new fridge. I already spent the money on the new fridge. Why should I have to go buy a new one now after 2 years, that I cant afford. Its ridiculous how many other people are having problems. Its a defect and should be recalled and they should have replaced the crap fridge they sold me in the first place. You would think for such a big company they would do something but yet people are getting seriously injured and this seems like it should be taken to court for a lawsuit. I am extremely unsatisfied and wont ever buy a Maytag and will let all my family and clients through my cleaning business not to ever purchase a fridge from Maytag.

Purchased this washing machine 4 years ago and every time I do towels, blankets, linens etc. all ends up in the middle of the washer in an unbalanced situation. Cannot clear the balance even when rearranged. I assume this is what happens with all the upright washers now that the center agitation unit has been removed. I have to ask the question of who made this decision to remove the center part? A man who never does laundry?

We bought our Maytag Bravos in December 2010. Four months out of warranty, like many other complaints Ive read, we started getting the loud jet taking off noise from the laundry room. Now we are having issues with the lid lock not allowing you to get to the clothes. This machine tries to spin three times and then locks up. It literally locks the lid and will not allow you to get to your clothes! For a machine to fail just four months out of warranty is a joke! After investigating the problems with the machine, it will cost us more to repair than what we originally paid for the washer in the first place. Give me a break! There should be a recall and Maytag should have their feet held to the fire to replace these less than adequate high-dollar machines!

We bought a top-loading Maytag washing machine in January 2020, and are very disappointed. Clothes do not come out clean. We called the Maytag call-center and were told that “high efficiency machines are different”. They use much less water to be green, but now I have to wash items several times, negating any energy conservation. This also takes more of my time. If we use the “deep water” option and power cycle, clothes are almost clean; however, it takes 1 hour and 45 minutes per cycle. My 18-year-old Whirlpool washed clothes beautifully in under 45 minutes. This brand-new Maytag is NOT an improvement. We use the correct HE detergent and have tried with warmer water, and all of the different cycles, but still do not get acceptable results. The Maytag washing machine is not effective at the one thing it is designed to do, clean clothes. Our specific model is MVWC565FW1, however the saleperson told us that all models are similar.

Maytag is a reputable company and my centennial washer has been going strong for over 6 years. My only complaint is that if it gets slightly scratched by objects placed on top temporarily, it starts to rust there.

Bought a Maytag Model #MDB8949SAMO dishwasher. After LESS THAN 2 years the motherboard stopped working. Called Maytag to complain, but was told they couldnt do anything. I would give the dishwasher less than a star but the rating system wont allow it.

I spent extra money on a commercial grade Maytag dryer $1300 before taxes because it had a 10 year warranty. The motor and drum quit - and Maytag refuses to honour the warranty. I am appalled by their dishonesty and lack of integrity. I do not recommend them to anyone.

I purchased a Maytag dishwasher model #MDB6769AWB2. After 1 year and 2 months of light use (just my wife and myself), the control panel went out on it! I called Maytag and because it was over 1 year old, they would not do anything about it! When you call their number listed in the owner’s manual, they thank you for calling their Customer Experience Center. This is an experience I can do without!

The digital display on our Maytag Washer model MVWB765FW, bought 3/22/2017, failed overnight (whilst the machine was not operating) after 3 1/2 years. A reputable firm came out and diagnosed the problem, their report concluded that the Control Board had failed and needed replacing: they provided a verbal quote of $525 [ ! ] to do that. The machine cost $600 and based on the expected life for washers (per Consumer Reports) of ten years would have a maximum residual value of $420 based on straight-line depreciation. The retailer from whom we bought the washer told us that he had contacted Maytag and asked them what they were prepared to do about this failure: a week later and absolutely no response from the manufacturer. Apparently Maytag has no concern for their customers or their own reputation. We made the mistake of buying this machine based on Maytag’s reputation and a ten year warranty which appears to cover only parts unlikely to fail! NO MORE MAYTAGS FOR US.

I bought this large capacity top loading wash machine about 22 years ago and it has yet to fail me. It had never needed any repairs and cleans my clothes wonderfully. The brands reputation is well earned. Great washer!

Bought a Maytag Front Load MHW6000AW washer and had a problem with amount of water in wash cycle. Dealer sent service men 3 times and changed several parts but washer still did not work and both repairmen said they did not know what was wrong. They called Maytag Tech Support but those people did not listen and said if no code shows up the machine is operating properly. Maytag then sent another company repairman. He worked 2 hours and said he could not find the trouble and Maytag support hung up on him. Maytag then sent another company repairman and he did one test and said the machine is fine and left in about 15 minutes total time. Now Maytag refuses to send another company for another opinion but I have a $1200 machine that still does not work properly. I am totally dissatisfied with Maytag and will stay away from their products totally. Companies wonder why people buy foreign equipment and this is the answer. I had a Samsung washer and never had one bit of trouble with it.

We purchased a new Maytag washer and dryer from Home Depot; a couple months later the dryer started to rattle so we contacted Maytag and they sent a service tech out who stated this was normal as the dryer was settling and parts are not as tight as they are when new. This was a garbage response and he was asked to leave. I contact Maytag again, told them of the problem and the tech response and they offered to send another tech out except I would have to pay for the service call since they already sent someone out. I sent them an audio file of the rattle, no reply. Eventually Home Depot ended up replacing the dryer as Maytag refused to help me despite it being in the warranty period.

This Maytag dishwasher is beautiful inside and outside. I love that the controls are hidden. It cleans dishes very well. It has a large capacity for dishes, a rack for glasses/mugs, a small rack for cooking utensils, and a container for silverware. It is so quiet you hardly know it is working. I would highly recommend it.

Our washer/dryer combination (2005 Maytag Neptune MLE2000AZW) has given us nothing but problems. The main problem is the stink from the washer. The unit is no longer usable and we are searching for a top loading unit to fit in the space. I am so angry - how did this piece of junk ever pass Maytags quality control?

I purchase this dryer not even a year ago. It is not performing right. I call customer support and they willing to try something to see the problem. I hope I don’t have to pay anything out my pocket.

We purchased a Maytag stainless steel French door refrigerator from Home Depot in 2011. The thermostat control (a circuit board made in China) broke and was replaced in 2012 by a certified repair person. He reminded me to dust underneath regularly, which Ive done. A couple of weeks ago I noticed some darkening of my wood floor to the left of the refrigerator and so I pulled it out from the wall a bit. What I saw was that my entire floor was wet and falling apart under the left side and when I looked into the freezer, I pulled out the bottom basket and the bottom was covered in about an inch of ice.I called, posted on Facebook and was put on hold several times for as long as 20 minutes before I hung up. I called Home Depot and asked them to intervene and speak to a rep from Maytag. I have heard nothing. There is black mold in the corner of my kitchen and a soaked floor that may go way beyond. I googled the leak and apparently this is very common with Maytag French Door refrigerators. I have a meeting with an attorney. Getting through to Maytag is seemingly impossible unless you have hours to wait on the phone. We have been getting sick for months and not knowing the cause.

I bought a Maytag Bravo washer with the new stainless tub and the bottom agitator. It also has a clear glass lid. Mistake. I can see the action of the washer thru the glass lid and it definitely doesnt wash the clothes very well. They just stay in the same position and the bottom clothes get agitation but the tops ones just sit there. The towels especially smell musty after they have been washed. Probably because they dont get agitation. The water level is so low that the clothes barely get wet. It was a good idea of the company to save water and electricity. But they must not have thought about getting the clothes clean. If I could I would get rid of this machine but I wouldnt want to subject anyone else to this type of washing machine. I would feel badly selling it knowing that it doesnt get the clothes clean. So I would never suggest getting a Maytag washer with a glass lid because you dont want to see what it is not doing.

Purchased a Maytag top loader. Hand wash clothes leaves a soap residue on clothes. Called Maytag they sent service out. Service tech said (off the record) the design of the machine does not produce enough water, but reported that machine works. Called Maytag again and they said they would need to send out a Master technician. So I set up another appointment (had to take more time off from work) with the Master technician. It was the same guy that came the week before! He didnt bother coming in to look at it! Called Maytag again and they said they would only be able to schedule a service call and if they come out and there is nothing wrong with machine, I would have to pay for the service call!!! I asked for a supervisor and explained why would I do that and he said they would send out another service technician from another service company and I wouldnt have to pay for it. He also offered me an extended warranty for a year for free. Thats great, but my machine is not fixed. This service technician said (off the record too) top loader machines are no good, do not buy, not enough water. He was there less than 5 minutes. Just got off phone with Maytag again and they can no longer do anything else, that the machine is working. I explained to the gentleman that yes the machine fills with a little bit of water and drains the water but it does NOT clean the items! Not going to let this happen to someone else. Plan on spreading the word to everyone to NOT BUY A MAYTAG TOP LOAD WASHING MACHINE. DOES NOT CLEAN YOUR CLOTHES. CONSTANT RESIDUE LEFT ON CLOTHES!

Maytag never fails to please me. My dishwasher is so quiet I sometimes have to put my ear next to it to make sure it’s actually working. The inside is stainless steel (those are the quietest) and it has a child lock so my 2 yo grandson can push all the buttons he wants and he still can’t mess things up. I love the high temp and sanitize features and everything is always clean and dry when done. It seems like it takes a long time to run through all the cycles, though. That and no adjustable top rack are the only two things I miss with my previous dishwasher.

This is Maytag model: MVWB765FWO-Top loader. HE rated. It handles mixed loads without balance issues but I cannot yet address reliability. The new machine averages 7+ loads weekly and is in the 8th week of use. The overall performance is clearly superior to the Kenmore Elite it replaced.