My refrigerator is a lemon! We bought a Maytag bottom freezer French door refrigerator model #MFD2561HEW in May of 2007. Less than a year later, it stopped working and ruined all the food inside. I cant remember the problem that time, but it was fixed by Maytag and we were reimbursed for a portion of the food we lost. Two years later, the temperature got warm in the refrigerator and freezer sections, and we were gone for a couple of days, so when we got home, all of our food was spoiled. This time we had an extended warranty in effect and they replaced a circuit board, but we were out the food. A few months later, the same thing happened. This time we were home and saved most of the food. The compressor was replaced, again under warranty, but it took 2 weeks to get the part. Now, less than a year later, the freezer and refrigerator compartments are getting too warm and frost is forming in the back of the freezer. When it finally does get cool, it freezes the food in the refrigerator section. It also makes loud bumping sounds. I paid $80 to a repairman today to tell me that theres nothing wrong with it, thats just the way it runs! He suggested I put a gallon of milk jugs filled with water in the freezer to hold the temperature when it starts to rise! This piece of junk is just 5 years old! When I complained, I was told to call Maytag and discuss it with them. This refrigerator was not cheap and I see that many others have had similar problems. How do they get away with selling an inferior product?

First off. Maytag customer service is horrible. I purchased a Maytag washer & used it 8 time. It now doesnt rinse the soap out of my clothing or even clean anything. The washer isnt broken because thousands of other people with the same exact washer have written negative reviews everywhere online. The washer needs to be recalled & never sold again. Maytag is making people SICK and they dont care. My whole family had skin irritation because we didnt realize our new washer wasnt rinsing.

I owned an front loading Maytag Neptune Front Load Washer MAH5500 for more than 10 years and first 5 yrs doing 2-3 loads a day for a family of 12 so this machine held up well, and only issue we had with the machine was the rubber around outside needed to be replaced after about 9 yrs.

The machine has left pin-sized holes in finer clothing since we first used it. I had purchased the extended warranty so they were called out to repair the issue four times during the warranty. They replaced the drum, but I still get holes. I think it is because there isnt enough water to rotate the clothing and it rubs repeatedly against the same spot on the other clothing. I have a see-through lid and you can see that the clothing just moves very slightly in the same position. I separate all clothing that has a zipper or any trim that may rub against the finer fabrics, but I am still getting pin-sized holes. We requested compensation or a new machine. They extended the warranty. We have replaced enough clothing that we are now buying a new machine. It will NOT be a Maytag.

I bought my Maytag stand alone dishwasher model # MDC4650AWB in August of 2009. I have used it once or twice a week since then. About 2.5 years ago the control panel crapped out. I forked over the $$$ to have the part replaced and installed. Now, 2 years later the panel is once again slowly dying. I just got off the phone with the Maytag people and they refuse fix it and take responsibility for the product failure. The machine has worked adequately for me aside from the control panel issues. The control panel was built to break. Shame on Maytag! Lets go forward with the class action lawsuit!!!

We love our Maytag Dishwasher! It's very durable, doesn't use a lot of water and really gets our dishes exceptionally clean. The best part is that it sterilizes on the final cycle! We've long trusted any Maytag appliance in our families for generations.

Same as all the others, bought this dishwasher about a year and a half ago for a new home. Didnt get the CO until 3 mo. ago and already having same problem with the keyboard flashing and not working properly. Very pathetic to believe less than 100 washes and were going to need a new washer, that works out to be about $ 5.00 a load. Wish someone could help. Model mdb7749sbb0. Thanks.

I received my Maytag dishwasher in November of 2013 from Home Depot (It was a month overdue the expected delivery date). It was installed by a certified electrician/contractor. By February of 2014, the control panel had to have its first replacement. It is now July 2014 and we are having the repairman come out to replace the third control panel this Monday. Supposedly there was a recall on the control panel and the one replaced less than a month ago was the improved/repaired one. We are beyond frustrated. I too sought Home Depot for help after the first repairman they suggested charged us almost half the cost of the dishwasher for his repair. I have already sunk over the price of the product into repairs. My Maytag dryer broke last week as well. Someone needs to get involved with this situation, perhaps a contact to the media? I think we are all being scammed and deserve refunds by Maytag for the dishwashers and our repair costs.

THIS PRODUCT IS CRAP!!!! I spend $699.00 at Home Depot, after 1/12 years the console stopped working. Maytags engineering staff should be fired!!! You stole my hard earned money. NOT once, but on a washing machine as well. I will never buy a Maytag product again. HEY NO WONDER THE REPAIR man sits on his ** the rest of the company does too! I dont have 250.00 dollars to fix this thing. Shame on your company. No wonder you dont want anything. DONT BUY MAYTAG, buyer beware. I am angry but this is not **!

Maytag water efficient, no central spindle top load. Clothes come out with scum on them. Really a problem on the solid darks. I have to scrub with terry cloth to remove. Maytag insists this is normal. Refused to honor warranty. Usually check Consumer Reports for quality and best buy. Energy/water efficiency is important. I like to have some control over the machine so that I can use it the best way for me. Such as soak. This machine cannot be manually controlled at all. Also it doesnt have a lint catcher, doesnt filter the wash or rinse water at all. All the lint and pet hair remains on the clothes or even gets worse.The clothes are not clean. I have no way to control the machine for my use. It may be water efficient but seems to use too little water to clean the clothes. Maytag wants to blame the EPA - This is irresponsible on their part. Its an awful washing machine and they made it. Maytag continued to insist that scum on the clothes was working normally. This scum was added by the machine. I used very little detergent; the clothes were relatively clean - just lightly wore a few days. They come out of the machine with streaks of white scum that I have to scrub off. The clean the machine cycle uses a huge amount of water. This is really DUMB: washing the machine instead of cleaning the clothes! Terrible! And Terrible customer service at Maytag. DO NOT BUY MAYTAG.

Maytag mod# MBF2258XE81, Ser# K04712605. 3 years old. At 6 months old, the drain plug clogged. Freezing water under pull out drawer of freezer, spilling onto kitchen floor. Fixed under warranty. 9 months later the same thing. I had to pay $190. Now, it has been happening for 6 months, and I use a spatula to lift the sheet of ice out. I have to do this every 10 days, or it leaks onto the floor, tile and rug in my kitchen. This is just wrong. I see I am not the only one. If Maytag does not fix this known problem, I guess I will get a new fridge. I had my last fridge for 21 years, never had problem. Thought I was upgrading.

Started having problems summer 2017. My dishwasher leaked and tank replaced, followed by drain pump, followed by circuit board in 2017. Didn’t have use of it for months. It has started leaking again as of Sept. 17.

Totally DISGUSTED!!!! Have owned my range for several years! Love have double ovens, however it is double the repair!!!! Every year we must have the handles replaced as the connection loosens and handles fall off!

We purchased the washer and dryer combo brand new from Lowe’s, had them delivered and hooked up together when we first purchased our house in the summer of 2016. 3 years later, both (expensive!!!) machines are having problems. The timer had to be replaced on the dryer, and the entire electrical panel on the washer has gone out and needs to be replaced. So disappointing. Model number MVWX655DW (washer), MEDX655DW (dryer).

The washer is very aggressive - it will tangle the clothes and actually tear them if they are thin. There is little control with the speed or water temperature or with the amount of water for a load of clothes.

I purchased the Maytag metal interior two years ago, the very first year I had to replace the control panel board... Now, the panel went out again, after calling the Maytag executive office, they finally sent me the part, telling me I had to pay to get it fixed. That was just three months ago... Presently, the dishwasher has quit running water in the cycle... I will NEVER purchase another Maytag dishwasher... thinking you get The Best doesnt mean what you think... BEWARE...

My refrigerator temperature control panel started flashing lights and the ice maker flap started opening and closing over and over. I checked online and there are numerous model #s doing the same thing, most all contacted Maytag, some were fixed for no charge. Some were not even though they admitted there was a defect in the electronic control panel. I was one of the ones they refused to fix because they said it was an older model but they fixed a 2006 model, a defective part is a defective part no matter the age especially if they know and admit there is a problem with the control panel.I cant understand why they wont take care of their problem, so now I have to spend over $300.00 to fix a problem that they made in manufacturing, that is not an outrageous amount, thank goodness, but I just dont understand why they wont stand behind their product when they can fix out for probably half that cost to take care of their problem. I didnt make the refrigerator, they did.

In 2011, I purchased 2 Maytag dishwashers, one for my tenant and one for myself. In 2014, the circuit board on my tenants dishwasher failed, when the unit was only 3 years old and of course out of warranty. I first contacted a local repair person, and he informed me that the repair plus service would be close to $300. When I contacted the company, after about an hour on the phone, they agreed to send their authorized repair service person and after his evaluation, would repair the unit with no charge to me, as a courtesy. This whole process took about 2-3 weeks. I felt that was fair. It is now 2015, and my unit, which I purchased at the same time and the same type, now is not working due to a faulty circuit board. My tenant uses her dishwasher more frequently, and that is most likely why her circuit board went first. This is a design flaw, or perhaps planned obsolescence. At any rate, Im not happy with this, and my model is mdb7809awb2, and serial # is FO4205659. Do you know if there have been any other complaints on this? Thank you for your help.Updated on 07/30/2015: After I wrote my review, I contacted Maytag about the problem. After considerable wait times, I spoke to someone who set up a diagnostic repair call, giving me the impression that Maytag would cover it. When the repair company called, they told me that I would be charged $104.95 just for diagnostics. Labor and parts would be additional. I called Maytag again, and they agreed to let the repair company charge back the diagnostic fee. After diagnosing the problem, it was determined the problem was the control panel and not the circuit board. The cost to repair with tax came to $315.85 and it was only this low because the repair company waived the return service trip. I can get a new dishwasher for a little over $400.00. I am very disappointed in Maytag, because I remember the commercials where the Maytag repair man was bored because the products were so dependable they never broke. My unit is only 4 years old, and its sad that it costs so much to repair it.

MDB7749SAW - 22 months @ an initial price of $599 and control panel lights become increasingly erratic and finally machine fails to respond to reboot (unplugging) after the third time. Repair man over the phone is familiar with the model and estimates parts at $160 + $115 (gave me a discount) + $125 service call for $400 to make the Maytag run again. Bought June 28, 2012. Installed September 2012. Becomes trash July 2014. Wish I could be more helpful... but if I had purchased the service insurance agreement, it would have run about $90/year... that would have been an extra $180 for a total of $712 including sales tax. So, I had a dishwasher for about 95 cents per day. Nobody rents them. I cant give it less than one star or I would. As a new buyer I was not informed.

Within 2 months of 1 year warranty running out, the control panel went wacky - does all kinds of weird things except work right. Called to see if there is any suggestions or work arounds and was told they would be glad to set up a service call for between $70 and $100, where they could tell me how much it would cost to fix. As with the other 100s of folks with the same problem, they basically said gee, you should have bought an extended warranty. If you have this many people with the same problem then it is Maytags problem, not the poor sucker consumer who got stuck with it. If you are considering this dishwasher, run, dont walk, as far from a Maytag or Westinghouse product as you can get. If anyone starts a class action suit against this product, please count us in!

Mine is the Chrome Maytag four-burner cooktop model. About $700. I installed it with ease. After two years there are only one or two slight scratches. It sees full meals for two cooked daily. The grate is first class and looks new, the top itself is easy to clean with a damp soapy cloth and mineral oil. There is easily enough BTU power for any size of pro pan. The igniters are healthy and fine and a repair would be easy.

I bought a new washer and dryer on Sept. 9, 2011. Front Load Commercial 2000 Series. I have had Lowes to my home 2 times since it was delivered because it shimmies across the floor. I am very upset with the purchase of the Maytag front load washer. If you could please get back to me on what can be done. I would like for a representative to contact me and come and look at the situation.

I purchased my Bravos washer in 2011. Three days before the warranty was up, the motor went out. It was leaking oil and had to be replaced. Two days later it quit working again I had to have another repairman out and found that the gear shifter had popped off so he put it back on and charged us 85.00. Luckily my husband watched him repair it and knew what to do if it happened again, which it does just about every 2 or 3 loads so I have to pull it out and pop the ring back on. I waste more water than I save with this machine. I have to drain the water so I can move the machine out and start all over because they didnt wash, and that wastes more soap. I would get laundry done cleaner and faster if I beat it against a rock. This is the worst washing machine I have ever owned and I will never buy a high efficiency washer or another Maytag again.

Let me make it simple for you, DO NOT PURCHASE A MAYTAG/WHIRLPOOL product. Maytag/Whirlpool believes its products should work for 1 year and then become obsolete, at least this is what the Maytag/Whirlpool customer service line told me. I purchased a MVWB950YW (Bravos XL) top loader on September 4th, 2012 for $948.00 plus $99.00 for an extended warranty. The washer worked marginally well when it was brand new. June 2014, the washer in spin mode started to sound like a freight train was about to run through my house. When I called for service the service company immediately signaled it was a bad bearing and offered me $500 to put towards a new or refurbished Maytag!!! They claimed if they were to repair the machine it would VOID the extended service contract?? I wanted the washer fixed, I did not want to spend more money to buy a new machine. I continued to use the machine as is, with the incredibly loud noise. June 2015, the same machine starts to leak water and is even louder. Again the company in charge of the service contract offers money for me to put towards a new or refurbished machine. Net is, Maytag/Whirlpool engineers its products based on its warranty - 1 year. Anything after that they view as an opportunity to steal more money from you and I the consumer. Do yourself a favor and NEVER purchase a Maytag/Whirlpool product. I would like to think American products are superior to its foreign counterparts, however Maytag/Whirlpool is not in this league. In my opinion, Maytag/Whirlpool has lost the privilege to call itself American and should no longer be allowed to do business in this country.

Maytag/Whirlpool dishwasher control panel FAILURE MDB7749SAM - Just like all the above comments about this dishwasher... I too have been a victim. Control panel stopped working after 1 1/2 years. Turned on by itself like other have commented and will not let you push any buttons. Maytag/Whirlpool refuses to do anything about this at all and will cost me over $250 to fix an appliance I purchased at $499. How disgraceful of a company to not stand by their product... A huge shame on you Maytag/Whirlpool for not standing behind your product. If anyone knows of a way to get involved with a class action suit against this company I would like to get in on it.

I inherited the Maytag Bravo washing machine when I got married... should have stuck with my LG! The Bravo does not clean clothes properly, I have to wash fewer items in each wash and wash them on the power cycle! Wasting time, water, and electricity! Will be purchasing a different brand!

I bought a Maytag MMV1153BAW Microwave. Within a year, the electronic key pad started cracking from normal use. After two years, the microwave intermittently starts then just stops, with the key pad showing 0000. We must unplug the device, or turn the breaker off and on. I called Maytag about the key pad and they said it wasnt covered, and a replacement key pad cost more than the microwave. After two and a half years, we purchased a new microwave, and have sworn never to buy Maytag again.

Im writing in reference to Model # MF12569YEM2. Bought this 3 years ago for close to 3k. Since then it forms a sheet of ice under the bottom freezer and leaks water onto the floor. It has ruined my hardwood floor and leaked through the floor to my basement and now need to re-sheetrock the ceiling. Its a bad design and should have been recalled because I see everyone else with this model is having the same issue.

I am 65 years old and for all of my life there has always been a Maytag washer and Dryer in our home. My great grandmother and great grandfather had a gasoline powered Maytag. My maternal grandmother had wringer-Maytag and my parents have always purchased Maytags. When I was on my own I purchased Maytags. In November of 2012 I purchased a Maytag Bravos XL washer and dryer. I had no reservations because it was Maytag. In October of this year (2017), the washer starting roaring and I had purchased an extended warranty. I called a reported this. A local appliance repair provider was sent out after I called the 800 number on the warranty agreement. I waited several days and finally called the repair provider and was told the parts needed were backordered. Time rocked on several weeks with no communication until I began calling both repair provider and warranty company. Still no washer repair. Ultimately, the resolution was not to repair or replace the washer, but to refund the purchase price and sales tax. The Home Depot salesman that sold us the washer and dryer, as well as the extended warranty coverage assured us that should either the washer or dryer fail it would be repaired or replaced, neither occurred. This left me without a washer for more than a month. Then finally I called the warranty company used by Home Depot and I was told a refund check would be sent for the washer, along with laundry reimbursement check. My difficulty with this is even though I got my money back on the washer and some of my expense on having the laundry and dry cleaning done elsewhere, it does address the issue. Simply, I see the Maytag commercials all the time and they are simply noise on TV now. I am still wondering how this could happen to a washing machine that had less than two and half years of use, never abused, cared for could fail in five years. I was used to having Maytags last decades with little or no repairs. Given the fact this machine was top of the line and well taken care of, I so very disappointed and not buy another Maytag of any kind again. By the way, I have a home in the country with a 27 year Maytag washer and 20 year old Maytag dryer that come from my home in town that Bravos XL dryer replaced. My research during all of this has led me to conclude this is not an isolated incident, but far larger problem with these washing machines. Why has there not been a recall on these inherently defective washers been issued. Where is the justice in this, even though the refund and small laundry reimbursement has been received it does not make any happier. I have lost my confidence in Maytag and I thought that could not happen with Maytag.

Its frustrating the way the bottom of the dishwasher has curves making wasted space. Second, the tracks for the trays are such that often the tray comes off the track and makes it difficult to get back on without unloading dirty dishes to do so. Finally, I really dont get the lighting system for dishwashing on the outside of the machine.

I purchased our washer and dryer together in 2012. Now my washer is making a really bad sound on the spin cycle. I talked to Maytag in Tenn. and they wanted 130.00 just to show up. Plus 300 to 500 for the parts that was needed. Wow. I am retired and on a fix income. I called a local repairman in OkC. After telling him the brand of washer I had, he said he would not come out to fix it because of the money would be expensive. 300 to 500 dollars for parts. He said it would be cheaper for me to purchase a new one. This seems to be a real problem. I talked to Maytag supervisor and she could not wait for me to get off the phone. Nor would she give me her name. Buy Whirlpool!!!!!!!!

Bought a MDB7601AWW, and then replaced front panel to stainless. Configuration options are great (can’t find better at cost up to $1,200.00)! I haven’t had an issue with any stains on non-stainless tub. Problem is now control panel failing for second time. After 1st time, sealed all connections in silicone to prevent steam from affecting it, as recommended on DIY video. I just replaced the door latch, thinking that may solve it, but hard to troubleshoot without any indicator lights. This second failure (2 yrs later) shows no indication that steam or water caused it. It does start now, stuck on heavy wash, heated dry, sanitize - per top lights. Front lights totally out. Debating whether to buy a new dishwasher ($$$) and give up super config (hard to find fold-down tines and fold-down small shelves on upper and lower racks, clips for small items, and basket that can be changed, placed anywhere) or spend at least $162 for the panel AGAIN and hope I get another 2 years from that while trusting that some other element doesn’t go out. I believe Maytag should, at minimum, make the panel reasonably priced by offering a rebate, since the part is not sold directly through them. Obviously this problem is a design flaw. I am the only one in the house, so the dishwasher is not under heavy use. At least I found how to replace it myself on YouTube, though it requires the door to be completely taken apart and would be easier with an extra set of hands and a younger back. Hard decision since it seems newer, expensive appliances have problems as well. If I buy new, I will not hesitate to get an extended warranty (1st time ever).

This machine may save water but I spend more time and money getting out the severe wrinkles it creates. I use my dryer and iron much more than with my previous washer. I never thought a new washer would make wash day more difficult.

I purchased a new Maytag from Home Depot. It was delivered and installed by them on 7/20/12. Today is 9/18/12. It is less than 2 months old and the tub is starting to shred around the upper rim. I called to get it repaired. What a nightmare. First I tried to understand a Filipino woman through a bad connection. She advised me to call a different customer service number, 1-800-688-9900. I talked to Crystal. She called up information on me using my phone number. She asked for the serial number as she had the model number available from the online registration I completed on 7/20/12. I told her I do not have that and asked where it was located. I also told her that I was unable to get it at this time as I am handicapped. She advised me that I had to show my repairman the receipt or I would have to pay a $60 service charge. I get nervous about throwing good money after bad. So I then asked why. If the serial number is so important, why is it not a required info when you register online? She had no answer. I asked to speak to her supervisor. I waited 4 minutes. Enna finally came on the line. She gave conflicting info about my online registration. She said I was not registered online (if not, how did Crystal have all my other info including my model number? Why did Crystal tell me I had registered without the serial number?). Enna told me that the repairman could key in the serial number when he gets to my house and if my washer was under warranty, I would not be charged. Again I asked why, if the serial number is so critical to the process and with all the info they seem to have on me (name, address, phone number, model number, place of purchase, date of delivery, etc.), why is the location of this very critical number is not in the owners manual? Why do they allow you to register without it online and why dont they track sales and delivery by serial number? She was unable to address these issues. I asked to speak to her supervisor. She told me she would give me her supervisors name and number (Kim, **) but she would not give me a last name or contact information. She told me that she was the highest level that I was allowed to speak with.Bottom line, my Maytag is falling apart, getting through the red tape to get it fixed under warranty is silly. Maytag ignores its own concept of tracking by serial number and does not support the use of serial number by telling you where it is located on an appliance or requiring it to register online. Calling customer service is a joke! I was mad when my new $800 washer started to fall apart. Now I am just sad with the way we allow manufacturers to treat us. Mad about the way we allow them to operate in the United States. They create junk or junk parts overseas, products fall apart over here, calls for repair get routed around the world, and then they create more red tape and call it customer service. I made one bad choice. Hopefully, you are reading this and can avoid your own.

I had my Maytag washer and dryer just barely over 30 days. My washer sounded awful and I had to get a new motor. Then my clothes would come out with dry spots. Not enough water. The computer was replaced and within a few months of purchase, all the major parts of my washer were replaced. I hate it! My clothes still come out with dry spots and it is loud. Worst major purchase I made. Dryer so far has been ok.

I have had this range (Maytag MER8775AS electric range) for 36 days. The hot surface indicator light doesnt come on (bulb is fine) and the heat elements turn on and off on their own when I am cooking. 36 days! This thing is junk! I am going to see if I can return it, even though it is outside the 30-day window.

I bought a Bravo washer 4 years ago from Home Depot. The spin cycle is stuck on high speed and sounds like a jet plane. Repair man came and said don’t bother to fix it because the bearing is gone. The machine cost close to $900. The repair man charged over $100. We are two retired senior citizens who dont do lots of laundry. I have read numerous complaints about the Bravo washer very similar to ours. Elder abuse should protect us from Maytag’s thievery and lack of help in repairs and replacement. A class action should be in place to address the Maytag Bravos manufacturing defects. There should be a recall and some type of reimbursement on this product . Please help us with this unjust situation.

We just replaced our 20-year-old washer and dryer for a new Maytag Bravos set. The Home Depot staff convinced us that top loading units were of good quality and reliable. We were fairly satisfied with our expensive purchase when our washer stopped spinning. We are just past our 1-year warranty of course so we called the service department. A young man in a beat-up pickup truck showed up and spent his time reading the manual that was hidden under the washer. His best guess was a $300 part plus a $100 fee for him to show up. So to repair a less than 2-year-old machine is $400. Im tempted to buy a different washer. It wont be a Maytag, unless you can convince me otherwise. I give you credit for great advertising! I was convinced that Maytag was a good name with limited repairs.

I write this as the repairman is fixing my Neptune washer. As with many other complaints, I was experiencing the awful mold smell with the only fix being leaving the washer door open when not in use. This works but for the past few years a switch on the front broke which means we have had to leave the top off the washer and rig it every time we used it. Sometimes it would work and sometimes an error code would show and I would have to just turn to spin and finish that way. At the same time in 2005, I purchased all Maytag appliances. First the microwave went out then the ice maker broke and is still broken, then the dishwasher went out and had to be replaced. Washer broke so basically the only thing that has had no issues is the oven and all happened just outside the five-year warranty. Never again will I buy Maytag.

We purchased this washer (MHW05500FWD) and dryer set in 09/26/2016 and have had nothing but issues. I have had the repairmen out twice. The first time the washer wasnt rinsing out clothes, when the repairman came out he couldnt find anything. In June of 2017 the same thing happen. Once again the repairman came out. I found out that there was a recall on the part which was on Backordered. Now the matching dryer model MED5500FWD is not drying. This is the worst washer and dryer I have ever own. I will NEVER own another front loader again. Buyer Beware!!!

The bleach dispenser will dispense bleach BUT it is full of water after each use. The dispenser is flushed with water by the machine at the engineered time in the cycle. The warranty service companies want me to pay around $300 ($100 + $70/ hr) for them to work on it. I have to use a measuring cup and pour water into the dispenser until it begins to siphon out. Stop pouring, and the dispenser will be empty for the next addition of bleach. The washer is allowing water to partially fill the dispenser AFTER the bleach has been flushed/siphoned out into the load of clothes. If the flush water were completely shut off after flushing operation, the dispenser should be empty.

We purchased our Maytag dishwasher (model MDB7609AWW2) on November 14th, 2009 from a local appliance shop in White Plains, NY. Total purchase price was $449, not including tax.Sometime in November of 2011, the unit stopped working. I tried every simple test I could think of to hopefully reset the unit. Finishing the obvious checks, I researched some possible problems on the internet latch micro switch, drainage problem, dirty latch, etc. Frustrated as nothing got it working again, I called a repairman recommended to us by the appliance store.The repairman charged me $75 for the visit just to tell me that the control board is shot. Even worse, and this is the reason for this letter, the part costs $329 plus $40 in labor! That is outrageous! If you do the math, I am facing the costs of a brand new unit to fix the old one. That might make sense if the unit was 8 years old but it is barely 2.I have sat on the decision now for a few days as I am beyond upset and I never make good decisions when I feel like this. But to recap, Maytag manufactures an appliance where its basic function - turning on - fails in 2 years and the repair cost essentially totals (to use insurance parlance) the unit. I find this absolutely unacceptable.I don’t expect Maytag to do anything for me. But I will say this; I plan on letting everyone I know just how this experience went. To make things worse, I am willing to pay for a quality unit but how does anyone know what that is anymore? For color, my grandmother has a KitchenAid dishwasher from the 1970s that is still running fine. No membrane controls, no delay functions or fancy BS super sanitary cycles and guess what, it has no control board, just plain old dials and buttons. Imagine that mechanical control? Built to last unlike the junk you see today.To remedy, I plan on picking up a used machine from the classifieds. I’ll install it myself and be able to do this for 9 years at $449, assuming it only lasts one year (I’m finding these units for $50 used). I may get lucky and find an old one from the 70s that will last a lot longer than that.

I bought this Maytag MCT washer and dryer set brand new from Lowes October 31st, 2016. When I washed the first load it made so much noise I thought it was broken. Called Lowes and they said it is just noisier than the older ones. This is the water/load sensing model, supposed to be great. I am usually here by myself, so at most I wash one load of clothes a week. I have a queen size mattress pad in there washing right now. This pad fills up the drum pretty much, I have it on deep water but that only gives me maybe 1/4 of the drum that has water in it. The pad is wet from wicking, NOT from the water covering it. How is this supposed to clean anything when the water is not covering the items?When it spins out, it gets off balance easily. The manual says to not worry about balancing load as you put it in there, but doesnt make any sense to just cram on one side as the water isnt going to float the cloth around to balance. The settings for Bulky does nothing more than the setting for Deep Water, you still do not get enough water to wash your clothes.It also does not do any good to add fabric softener to the machine, as it seems to just take it all out, you cannot smell any fabric softener on your laundry when you are transferring it to the dryer. And the laundry when dry isnt soft like it was with the old machines. I will be 62 in December 2017. My parents always had Maytags, never a problem. This is the 4th set of Maytags I have had. And bought a set for my daughter in 2013 also. And this by far is the worst. Their quality is completely gone now. Nothing but cheap made products that are predestined to fail. Friend across the street said she had looked at this set when she was in market to get a new set. She has an friend who works on appliances and who works for stores selling these models and he told her, they were not worth buying. Wish I had known that. Do not waste your money.

I purchased a refrigerator 9 years ago and the ice maker stopped working. When the repairman took it out there was plastic peeling from the ice mold. It cost $261.11 to have the ice maker replaced and the ice maker he replaced it with has the plastic on the ice mold. He said that GEs ice makers do not have the plastic coating but Maytags still do. I called Maytag and spoke to a supervisor and they said that there was nothing that they could do. I am filing this complaint because I feel that consumer need to be aware that they are ingesting plastic that is in their ice. I feel that Maytag should compensate me for the faulty part and also eliminate the plastic coating from their ice maker. This issue is impacting many other consumers and they need to issue a recall on the ice maker and replace it for free for other consumers.

I bought this washer on 6-29-14, should have returned it within my 30 days but kept thinking it will get better, NO. I actually like to use water to wash my clothes!! It doesnt even get all the clothes wet when using on the bulky/or any other setting. Very disappointed in Maytag!!! Washer for sale, very cheap even though I paid $500 with warranty.

We purchased a Maytag gas range, only to have the paint wash off the front trim of the oven door. The digital panel went out in the second year of use and is apparently expensive to replace. After going through reviews by other owners and discussions with repairmen, it was determined that these panels only last about a year and are defective. This problem is extensive with Maytag. My brother was a repairman for them and dropped them due to poor quality of workmanship in appliances and their dishonest approach to warranties. I should have known better. Dont ever buy Maytag!!!

Purchased this dishwasher about 1 1/2 yrs ago. Luckily the first two times the control panel went out, it was still under warranty (within the first year). Now its gone out again! This is the third time! What happens is all the buttons will work except for the START and CANCEL. This has been the same issue every time. I tried restarting it, made sure there was not a leak that somehow was getting to the internal electrical components in the panel. I actually know the Maytag repairman by name. Its nothing like those old commercials where the Maytag repairman sits around and has all the time in the world because their products never break. Those days are over and these guys are busy working to fix these devices they label as dishwashers. Since my warranty is now expired, it was an unexpected $96 service call to tell me what I already knew - Its your panel again sir, it needs to be replaced. Well have to order one for you and itll be $265 for parts and labor plus the $96 service call = $361 repair for something that will likely break again in a few months. Never am I buying a Maytag product again.

Maytag dishwasher mdbh979sam1 - Every single one of the Maytag/whirlpool dishwashers with soft pushbuttons and LEDs will fail--check it on YouTube. They have a very thin printed circuit strip from the door controller to the brains, and this rusts through in a few years. You must buy the whole controller for $150, you cant replace just the ribbon. And youll be doing this every few years. Maytag disavows this if you call them. The design runs the steam past this ribbon, so it corrodes really fast. Get a real pushbutton or a real dial knob model instead. With this model, the issue shows up when the LED pushbuttons stop responding or randomly light.

After using my GE Profile to death we replaced it with a Maytag; mostly for the cost. Although I hate to admit this, remember the old saying you get what you paid for - Well its true at least in the case of this Maytag oven. I am a constant cook and own a bakery, I often bake many of my products at home. Since getting this oven I have had nothing but failures. The cakes are over done, underdone, cookies burnt, not cooked enough; my time frame for recipes is so off! I wrote a cook book and have baked for years so I know for a fact its not some miraculous mishap that all of a sudden I cant bake. Ive had them come calibrate the oven but still no success.Im going to call them again but I felt compelled to let people know this is the worst oven in history and avoid purchasing it at all cost. I plan on having the service team come out one last time but if this doesnt work I plan on replacing it. Its a Maytag Double Wall Oven-Top Convection-Self Cleaning model no: MEW9630DS-SS. BUYERS BEWARE!

The serial number is MDB8979SBWD. Just a few months before warranty expired the buttons were being flaky. Eventually it would not start. We brought it to the dealer because they wanted $150 to come to the house. They replaced the front panel. It lasted less than a year and stopped working again. Being out of warranty and being a technician I took off the panel and saw that there was no insulation in so the humidity would build up. The wires in the ribbon wire were corroded. I looked up the price of the panel and it was $150. The dealer wanted $150. I did not want to replace it because of the possibility that was not the only problem. We paid $400 for it on sale, (a mistake I know better than to buy stuff on close outs.) FYI to get the dealer to deal with it it would cost $300! From reading these complaints this panel seems to be a real problem with this and Maytag is not supporting this LEMON. I see a lawsuit here. Too bad Maytag is only out for profit. What is disappointing is that Maytag is owned by Whirlpool. Whirlpool has or used to have good appliances. We had a microwave that lasted 15 years and our last dishwasher that lasted 15 years. We will never buy Maytag or Whirlpool again. Maytag is junk. The dishwasher is probably ok except for the panel. Shame to get rid of it for that but unless I can bypass it that is what we will have to do. $150 is too much for a gamble and it seems that panel is a problem so it probably would not last long anyway.

Maytag Bravos Quiet Series 300 washer/dryer - Purchased this set nearly 3 years ago from Lowes. The washing machine smells like toxic sewage. The Affresh brand cleaner no longer works. All of our towels and many of our clothing items have had to be replaced due to the stench. I surmise this is because it does not use enough water. The clothes get wrinkled badly, twisted, stretched out and torn. The dryer does not fully dry. Always had to run it again to get the items dry. Finally, it started making a horrible, loud, screeching and grinding sound. Neither the washer or dryer was quiet for long. Putting these out on my curb today for scrap metal pickup.

I purchased the washer 12 months ago. I liked large tub size and Maytag name. Thought I had made a good purchase. Boy am I am sorry. The washer overflows my large utility sink for drainage on large load setting and clean setting, ruining the flooring in an adjoining room. You cant wash black clothes in it leave white residue spots all over clothing. You cant use pod soap. Doesnt dissolve totally. Just on your clothing so you must wash again. So now I am trying to figure out what I can do but afraid I am going to replace it. Would Not recommend this product. Bravos XL MCT MVWB835DW1.

I purchased a Maytag dishwasher model number MDB7749SBM in May of 2013. In August the dishwasher control panel stuck on Rinse only cycle. It has been stuck on this cycle for a month. I contacted Maytag and they walked me through a reset. It has not worked. It looks to me as if the control panel has failed. This seems to be a common problem with the Maytag dishwashers. As soon as the warranty expires, so does the dishwasher. I purchased this dishwasher from Home Depot for over $600 thinking I was buying a quality product. My previous dishwasher was also a Maytag, even a lower end one that lasted almost 14 years! This one has not even lasted 14 months!!I was told by Maytag that I could purchase an extended warranty for $267.45 that would last a year. I believe, 4402 based on other reviews that I will be dumping more money into this one even after that. Very disappointed!! I will never buy another Maytag product again! I should have bought the Bosch. It was roughly the same price and high quality. I bought Maytag based on my previous experience. No More!!

Recently May 2019, bought a Maytag Bravos Washer, HE. Its now installed and so disappointed with this product. Not enough water to wash Clothes. Would of taken cashback from Maytag, but cant wait 6 to 8 weeks for cashback. 6 to 8 weeks after they have washer picked up. How long did we want to go without clean clothes, hummm. Problem was looked at by a professional appliance repair company sent by Maytag. His opinion, suggestion was, washer just didnt deliver enough water to wash clothes. I know its HE, suppose to me water miser, but Maytag Bravos just doesnt give enough WATER. How do we get clean cloth like that. As I mentioned in summary, I have added attachment close proximity to add water to washer raising water level to wash Cloth. Yes with proper water it does clean good, JUST NOT A AUTOMATIC WASHER now. Were only two, Rural NB, up to 3-4 washes per week, more when company around.

First off, everyone seeing this should be fuming as I am because we are mostly in the same boat with these control panel issues. Mine is Maytag model MDB7749SBM3 about 575.00. A little bit cheaper than most of you because I purchased at the online and had a rebate. About a couple months after the warranty expired, we started having weird light issues with the control panel where are one light would pop up when you didnt hit it or other lights would pop up when you hit something else. We kept dealing with it thinking that it would dry out and resolve itself. Lo and behold, just like it appears to be tens of thousands perhaps hundreds of thousands of machines, it quit. I read this consumer affairs post after it quit and now I know why it did. I opened up the control panel and sure enough, the little ribbon that connects all the electrical connections had brown on the back like it was burnt through. I was able to find a special 1 800 number that Whirlpool has set up because they have purchased Maytag and the woman I spoke with said they would send a technician out and that I was responsible for the diagnostic fee. I was born but it wasnt yesterday. I immediately said to the woman, Absolutely unacceptable. I am NOT paying for anything, very politely highlighting the fact that I know they settled a class action lawsuit in California regarding a control panel issue and there are hundreds maybe thousands of complaints on consumer affairs.com. The woman place me on hold, I am assuming to speak with her supervisor and then let me know that they would pay for the diagnostic fee. She said a repair date for me for about a week and a half later. The repairman had a good day because the dishwasher was already disassembled for him and he proceeded to take pictures and call Maytag. Maytag told him that I was responsible for the installation cost and service fee which according to the technician is about a hundred bucks. I told the technician that is fine but it will not be fine when I call Maytag back. I have not spoken to Maytag about the hundred dollars needs to file a claim for a new dishwasher and associated damages. I have not spoken to Maytag about the hundred dollars but I am only on this to let you know that every single one of us needs to file a claim for a new dishwasher in associated damages in small claims court. I plan on filing a claim for approximately $700 for a new dishwasher and damages. In my opinion, I feel like we should all do this, otherwise big corporations like this will continue to shovel garbage into the stores left and right.Have a good day and good luck with your court case hopefully. With all the evidence against them, I have a feeling that they will settle this and pay before the court date even comes around. Good luck to all of you. I will try and update this after I call Maytag back for the hundred dollars that they are going to charge to repair their broken part.

I purchased Maytag gas range in March 2011 at Home Depot, Model No. MGR5605WWO. I received the product in May 2011. The porcelain on the grates chips away leaving large grooves in grate, which affects cooking efficiency, (the fire burns erratically). First, I called 1-800-688-9900. The grates were replaced. And then same problem, it was replaced again, and again the same problem. The warranty to cover stove was extended by 6 months. The enamel on the round magnetic cover for the burner is also chipping away. I was told that this chipping of the enamel is a cosmetic problem and does not affect the functionality of the stove problem.A repair technician was sent out at my request to see firsthand the problem grates. I was told by him that if it occurred again, the manufacturer needs to be made aware of the defective grates. He noted that the enamel covering on the grates was not uniform. I have been told by Maytag supervisor today that she will get back to me within 3-5 days and let me know what is going to be done. I have had gas ranges before, but this is the first time this problem has occurred and its continuation is unacceptable. Is there anything further I can do to ensure I have stove grates that do not chip continuously?

We purchased our French Door, bottom freezer in April 2010 after a renovation. We have loved it besides needing more refrigerated space. This past weekend I noticed the appliance was cutting off and a few seconds later coming back on. It has an outside ice and water dispenser as well and the lights will blink on and off of course when the fridge cut off. Called for a repair and when the repairman called in the parts he was told he needed 2 computer boards. One was available however the other was discontinued and they would not allow him to just replace the one board. The fridge cost us $1798.00 from Home Depot. I cant believe how irresponsible Maytag is in this case. I have a kitchen full of MAYTAG appliances and have loved them all. But this is unacceptable. The Maytag fridge I had before was 16 years old. I gave it to a family member when we bought this one and that one just broke down last year so it was 21 years old! Whats up MAYTAG?

We purchased the washer and dryer pair...beautiful looking, no agitator, water efficient. Load sensing feature. TERRIBLE, TERRIBLE, TERRIBLE. WORST APPLIANCE WE HAVE EVER PURCHASED. Used it 3 times. Clothes would not rinse, left white soap residue in the folds of the black clothes, even after a second wash. Home Depot was just the GREATEST, they replaced it for us. We went with a less expensive model GE. With the agitator and full water load...save yourself A LOT OF TROUBLE, stay away from Maytag Bravos XL.

My husband and I are retired. In 2006, we purchased a Maytag stove, refrigerator and dishwasher thinking we bought the best. Since purchase, we have had repairs on all 3 appliances costing us over $1000. We are installing our 4th electronic control touchpad replacement today at a cost of $250.00 each. We had a new oven electronic ignitor replaced on the same stove. The compressor on the refrigerator had to be replaced! The drawer mechanism on the dishwasher had to be replaced. We will never recommend or purchase your products ever again!

When I went to use this machine (maytag bravos). I noticed there was like a 1/4 filled in tub, checked water flow, that was fine. Then read the manual that Maytag sees using Less Water is better for clothes, I always thought it was less detergent, ohh well. Wouldnt recommend this item to anyone.

I have trusted Maytag for many years, more than 60 years, my parents and then myself. My Dad always told me I could trust Maytag over any other brand and that has always been true until I bought a new Centennial Econoserve Washer. This is without question the worst machine ever made. I should have asked every question in the book concerning this machine but, oh no, I just trusted the name MAYTAG. I am so sorry. I cant trust it to clean anything that shows it needs cleaning so you have to wonder what does it clean that you cant see. Im sorry people, I just dont know what to do. I cant afford to buy a new machine and the store I purchased are basically telling me, Sorry, you bought a stripped down model. Too bad! I will never buy another appliance from that store nor will I recommend them to anyone. Too bad since they are locally owned. Anyway, Maytag, you blew it badly to turn out this terrible machine. Thats my story and Im sticking to it. Better product next time.

Lid lock issue. 2 years old. I will never buy a Maytag, or any other Whirlpool brand for that matter. I am VERY disappointed. A service call will cost at least $200 dollars so why not just buy a new washer for that price. Also, I read that consumers should stay away from automatic water level washers. They never work right.

On June 5th, my husband turn off the water to the house since we were going to be away for 4 days. Unfortunately, it was not completely turned off. When we left, the washing machine was OFF, with the door slightly cracked open (to allow for circulation). When we returned, there was water all over in our upstairs, plus water had gone down the walls to the lower level. We could not figure out how the water got into the washer since it was turned off. The insurance company asked that we call a repairman to find out what was wrong. Fortunately for the repairman and us, the machine continued to go on and on after the Curtis had checked it out (it pumped out for him but not for us) and turned it OFF. It jumped from cycle to cycle after he had turned it off. Obviously the control board did its own thing. Be aware-- it can happen!!

How can any company with a reputation that we all have grown up with MAYTAG pull such a DESPICABLE act on its customers of 20, 30, 40 plus years ??? $500+ repairs for each of 2 boards in nothing better than a BOAT ANCHOR... I would give anything to have my 15 yr or even 20+ yr old pair back! Worst purchase of our 50 years of life! Its overdue time for a Class Action Lawsuit! Also has no one had your washer jump and dent your dryer? Imagine a child in a room with something as Vicious as MAYTAG BRAVOS! Just as well have them play in the STREET! Lets all join together and show MAYTAG the consumer does count. Thank you...

We bought a Maytag Bottom Freezer Model MBB1952HEW in 2006. We have already replaced the relay, two years ago, now the compressor is going. I have seen recalls of the top freezer on the internet but not on the bottom freezer. It is concerning when you pull your refrigerator out from the wall as to how warm/hot it is back there. We were told it would be cheaper to buy a new refrigerator versus replacing the compressor. We are so disappointed in how much money we have stuck into this refrigerator for how old it is. I would expect a refrigerator from a reputable company to last longer than 6 years.

Purchased dishwasher Mod # MDB7749SBM1 thinking it was Maytag (lonely repairman) in June 2013 from Home Depot. Cost new over $1,000. As of March 2016, three service calls, two of which required replacement of the control panel. Now the control panel has failed a third time and we are told by Whirlpool (parent company of Maytag dishwashers) they will not cover the repair. They have offered a discount for a new dishwasher. Since that did not seem like a very good option to me, they offered to let me pay for current service plus a year for over $350.00. I was sad to discover that they are the manufacturer of most dishwashers available at your local home store dealer (Whirlpool, Maytag, KitchenAid, Jenn-Air, Roper, Amana). VERY DISSATISFIED CUSTOMER!!!

After seeing all the bad reviews about Maytag I decided to write my review, we purchased a Maytag washer and dryer 1990 when moving into our new home, and we still have the same set. Now it does not have a motherboard which I feel today is the major problem with most appliances. Get away from the motherboards. Turn the machine on and off when its supposed to, or let it run its Cycles. Dont overfill, because this causes wearing motor parts. The dryer belt wore out on the dryer but that was an easy replacement. Im a woman of 64 and get it myself. Maytag I hope that you get back to the plain ol simple washer and dryer because mine is probably going to wear out which I hope not but I would so love to get the same set I got now.

Tried various cycles and I hear water going in but don’t see any water. How does this wash clothes. I want to see water and soap clean the clothes. If I want dry cleaning I will bring the clothes to the dry cleaner. Never again will I buy a high efficiency washer. My clothes do not come out clean!

I purchased a Maytag electric range model # MER8775AS in Feb 2012. While boiling syrup, the pan overflowed onto the oven door. As I began to clean up the spill I noticed that some of the spill had gotten inside the door on the inside of the oven glass. To remove the stain would require disassembly of the door. I called Maytag and complained of what I called a design flaw and they said, No, its your fault for spills entering the door. They even sent a condescending email to me informing me that if I needed to purchase parts, where I could get them. I designed appliances for years and this is another example of poor quality and lack of consumer service. I AM DONE WITH MAYTAG.

Top loader Maytag Bravos type 588-03 - This washer is extremely slow and does a very poor job of cleaning. I use the recommended detergent (I use Tide HE) and follow the directions being careful not to overload. I can tolerate the slow operation I guess, but the poor cleaning is a real problem. When I put a plastic shower curtain in it, no clean happens. I just throw them out and but new every time. I will definitely go back to a Kenmore with an agitator.

This has been the worst washer I ever bought. First the washer does not fill with water even on the deep fill function. It pours little water and washes the clothes with basically no water. The sensor for the lid broke less than six months of using it, soap residue is left on the clothes. I do not recommend this washer at all.

I had a Maytag washer and dryer for over 25 years. I loved them so I replaced them with the Maytag name. They are not the same company as far as pride and product workmanship.From the get go it always had a dirty odor to the tub, as though the clothes had been left in it for days. I was told to just run through a cycle with bleach, but nothing. There is no lint collector and after about 8 years of using this washer, the old lint is in the bottom of my washer after every wash. Now, I have to deal with the thing coming to a screeching stop, not spinning out the water after the wash cycle. Sometimes it’s full of water and other times some water drained, but the clothes are full of water and not spun out.Now tonight, I went downstairs and found water on the floor, it’s leaking. My question is to call and get it repaired or not waste my money and go buy another brand. I may go with the latter.I purchased a fridge and dryer at Home Depot a few years ago. I wanted to stay away from Maytag name. I purchased another name only to find out it is part of Maytag. No wonder I’m having trouble with my fridge, making ghost-like howling sounds so loud it consumes the entire house. So annoying. Stay away from Maytag. They are not the same reliable, take-pride-in-work company.

I sent an email to Maytag regarding my Maytag Bravos washer which I purchased two years ago at a cost of $1,100. I have started having problems with the machine last week. I kept getting the UL error code. I called a certified appliance person to come out to find out what was wrong. I do not believe any of the appliance people know what to do for these machines.First, I was told it was the control board that needed to be replaced, then I was told the motor had a crack in it and it needed to be replaced, and then the springs needed to be replaced. So they replaced the springs. This was a Tuesday afternoon. It worked fine until Wednesday of the next week and I started getting the F51 code. Just let me say if you cannot stand behind your parts on a $1,100 washer that is only two years old, then something is very wrong. I am in for $159 on repairs so far. Who knows what the cost will be to finally get the machine repaired.

I have a 26 cu. ft. side by side Model MZD2665HES, like most folks in my neighborhood (spec homes). The icemaker died and service was called. They looked at solenoid, and replaced the ice maker assembly as a wag that it was the problem.. still no ice, but the water was still able to be called. I replaced filter- still water only, no ice. Little did we know it was the filler tube blocked with ice, and the service man didnt once suggest turning off the water service. SO, every time water was called to either make ice or to fill a cup with, it put intense pressure on the point of assembly where the water line comes into the fridge (water inlet tube). A pin hole developed in the little plastic bit (water inlet tube plate) and every time the water was called to ice, guess what happened - it shot right out the back on drywall.Almost $20,000 dollars worth of damage to wood floor (warped), drywall (jello), and flooring (carpet) ensued. Mold was all over and had to be contained and treated for days to be fixed. Im still duking it out with service repairman and insurance companies. My advise: If you have this fridge or anything like it and the ice maker stops working, IMMEDIATELY shut down the water supply, turn the fridge off and check the filler tube in the back for ice blockage. Probably a good idea to pull the fridge forward once in a while and check the back for water also.

Thank all of you for saving me. I was about to buy a Maytag with bottom freezer from Home Depot. No wonder they are marked down an additional 20% off their sale price.

While washing clothes in my Maytag front load washer, I noticed that there was water leaking from the front left corner from the bottom. I have owned the washer for only 2 years, and Maytag manufacturer (Whirlpool) told me that it was going to initially cost $80.00 for a service call and then more money to fix the leak. WOW. Also the wood floors that are underneath the washer and dryer, is starting to warp from the leaking washer. I would recommend DO NOT BUY A MAYTAG APPLIANCE. The warranty is basically worthless along with the washer.

JADE model RJRS4270. Had this model for 10 years with more than 10 service calls. Always breaking down and Whirlpool will not honor the warranty. Paid for an extended warranty service to Maytag/Whirlpool offered by the manufacturer. When unit broke Whirlpools warranty service provider Assurance said Whirlpool no longer provides the parts needed, sorry can’t honor the extended warranty you had paid for, no parts, and no refund. The evaporator drip tray had been replaced three times. Asked to have the unit replaced. Whirlpool was absolutely disrespectful and only offered me to the option to buy another discounted $8K unit for a with ~ $2K discount.So far approx. $6K unit + approx. $1K extended warranty (not honored) + approx. $1K parts and service out of my pocket (Whirlpool continued to tell me it was not warranted). Although the operator’s manual said it was covered. While under warranty Whirlpool doesnt have replacement parts to service it. Multiple service tech are telling me there are many known issues with this unit. Found out there’s class action law for the same issues Im experiencing. Whirlpool only offered a new unit at approx. $6K. So total for me to date if I choose to take the discounted unit would be $12K. Dont buy this unless you have a good lawyer. Hardly seems reasonable. Extraordinary time/money loss and aggravation.Bought 8/1/05 S/N ** Model RJRS4270C $5,400. Service call 5/10/06 Repair - Freezer dripping water and pooling on floor. Service call 6/28/06 Repair - Defrost drain problem, ice backup, drip tray. Service call 7/5/06 Repair - Defrost drain problem, ice backup, drip tray. Service call 7/12/06 Repair - Unit not defrosting. Service call 8/26/06 Repair - Freezer not cooling, ice backup, fan burn out, drip tray. Service call 9/2/06 Repair - Evaporator fan not working. Replaced unit 9/_/06 S/N ** Model RJRS4270D. Maytag Dependability Plus Cert No. ** $99.00 8/02/08 thru 8/02/11. Maytag Extended Service Plan Plan No. ** $297.19 9/02/09 thru 9/01/12. Maytag Extended Service Plan Plan No. ** $405.31 9/01/12 thru 9/01/2015. Service call 10/13/10 Repair - Ice build up in fan, freezer not working. Service call 10/20/10 Repair - Installed new drip pan, bi metal, fan motor. Service call ~ 8/_/15 Repair - Service tech states, Whirlpool no longer has parts. Even though we paid hundreds to have a still active Maytag contract extended warranty. Whirlpool outsourced service to third party. Service call ~8/_/15 Service tech refuses to repair because cant get parts from Whirlpool. Asked me to find part on eBay or some other source so he could repair since Whirlpool could not provide. Got part. He did fix. Freezer stopped working 4/2/16. Customer support 4/3/16 followed owners manual instructions for warranty and call number, Whirlpool said theres no warranty and to call any local service tech. (Owners manual said compressor was still under warranty). Service call 4/4/16. Tech refused to work this Whirlpool unit, believes to be issue with the compressor leaking or system blockage or bad valve in compressor. Customer support call back - Krisi, was warranted. Jade Specialty Department. Customer support call back - Jared, no warranty, sorry. Explained contract to him. Nope/Nada. Customer support transfer - Jan, yes was warranted. Asked to speak to manager/sup. Said if you won’t honor warranty then please provide replacement. Transfer to Mike said we must schedule service through Whirlpool to fix contradicts. We asked for reference number to track. Mike said they don’t use reference numbers (contradicts Jared from when he asked me for a reference number). Two days no call from Whirlpool. Customer support call back 4/7/16 - Kari, offered small discount for equivalent new or refurbished unit $5,739 for Model KBSN602ESS. Said although under warranty, Whirlpool may not be able to provide parts to repair unit, but they will sell me an equivalent unit.

Maytag washer was bought May 2010 with an extended warranty, which expired May 2014. This machine was used by two people with average wash loads. Five months later the machine computer programming didnt work and the machine sounded like a jet taking off. Whirlpool said a one-year warranty would cost $329! This would have been less expensive than a new machine, but I felt I couldnt trust having it repaired. A repairman very familiar with Maytag products said he had three service calls the same day with similar complaints for the Bravos 300 series. He told me the bearings were bad and the cost to fix was not worth the money and this machine should have been recalled. I bought another brand and will not buy Maytag again. When my new machine was delivered, there was grease on the floor from the Maytag.

I bought my Maytag about 3 years ago. Have had continuous problems and now the whole barrel has broke and dropped down. I was treated with disrespect from the repair man and will never buy another Maytag washer.

Chalk up another bad tub bearing. Washer around 4 years old. Repair man says $350 to $400 to fix. Also said sees it couple times a week. Said after Whirlpool bought Maytag quality nose dived. Maytag no longer top of line. Will never buy another Whirlpool or Maytag product. Just replaced control panel on dishwasher also. Amazon sells kit to repair washer. That should tell you how bad it is. Called Whirlpool to see if they had plans to do anything about this. No they dont. Stay away.

I purchased a small (14.5 cubic feet) refrigerator for my basement from Home Depot on January 26, 2013. It was delivered on January 30, 2013. On February 14, 2013, we found that it was not cooling like it was supposed to. The soft drinks in it were not cold. I called Home Depot and was told I had to call Maytag for a repairman to come out. Since it was so new, I felt it should be replaced. They disagree. The warranty only calls for repair. So a repairman came out on Feb. 19th. He said that it has no freon. He doesnt know why. It could have a leak. It could have leaked out in the warehouse. There is no way to know this. He said another repairman would be out to fix it on the 20th. On the 20th, no one showed up or called. I called the repair company, S & S Appliance of Bessemer. I was told the repairman that I needed is in Montgomery today and the repairman yesterday was told to tell me he would call me. He was told to not tell me someone would be out today. So now, I have to wait until tomorrow for someone else to call me and see when he can fit me in his schedule. I think Maytag has a problem with their refrigerators. I think Home Depot has a problem not standing behind what they sell. I think S & S has a problem with their servicemen. I am not happy with any of these companies and will never buy another Maytag refrigerator or washer, but thats another story.

After less than 3 years the interior lip of the machine is rusting. I found this when I was cleaning the interior of the machine because my white clothes were coming out with black soot on them. I can estimate that bleach was used in the dispenser 3-4 times tops over these 3 years. Very disappointed in the equipment. Ive submitted a complaint to Maytag with hopes of a favorable response. This should not be a warranty item...its defective design.

I purchased this dryer in September 2011. By August 2012, one month before the warranty expires, the thermo fuse blew and the dryer would not dry; no heat. I replaced fuse and 30 days later, it blew again. I replaced it again and now, March 2013, 6 months later, the same thing; the thermo fuse blew, no heat. The vent is clean and air flow is very good. Maytag will not admit a problem. This is not an inexpensive dryer; it may be cheap, but not inexpensive. Maytag quality appears to have vanished. I have Maytag throughout the house but will think twice before purchasing Maytag again. Chinese produced parts/products are inferior. Maybe Ill look at Bosch or LG from now on.

We have had and used this washing machine for over 25 years and only had one small problem and that was to replace the lid switch and the machine is working today as good as the day we bought it, it has went through raising four kids and many grandkids.

In August of 2009, we had an opportunity to remodel our kitchen plus add new windows and doors. How exciting! SO we had put down new flooring in our kitchen that matched our oak cabinets and since we had a little money saved, we wanted to purchase new appliances to match. We purchased a Maytag side by side with ice and water in the door. It also had the fingerprint resistant stuff on the outside. It cost about $1300. You buy name brand so they will last a while but here we are November 12, 2014, 7 years later and the compressor goes out. If repaired, it will cost $8090 to fix. Why do I want another Maytag. I got a citation I bought in 1978 and it still runs. Hello Facebook, you will my next visitor.

Ive had the dishwasher model MDBH979SAB0 for about 3 years now. A few months ago I noticed the faceplate would pop out when you opened the dishwasher. I would have to pop it back in. The dishwasher was out of warranty so I decided to attempt to fix it. I took the faceplate off to realize all of the plastic tabs that screws go in to were snapped off. The only fix for this is a complete new panel from Whirlpool Parts Online to the tune of $194.17 (W10811169).The wheels also fall off the bottom rack. The push pin plastic becomes brittle over time and does not stay in the assembly. To replace the wheel assembly (there are 4 in total) is $38.18 each (W10195416V). The wheels or push pins cant be purchased separately. Both of these items are not covered under warranty past 1 year. Maytags 10 year warranty only covers the upper and Lower Racks (excludes cup shelf and silverware basket), chopper blade and stainless steel tub and inner door liner. So only a small percentage of the parts.The design of the faceplate is defective in that too much force is applied to the faceplate when opening the unit. The handle is integrated in to the faceplate. The plastic used becomes brittle over time and breaks. The panel unit (W10811169) must be replaced in entirety rather than just its housing increasing the cost of repair. To have this failure occur within the first 3 years of use is very premature. I can only assume if I repair the dishwasher I will have the same problem again. I am considering buying a new model that is designed better and comes with a longer warranty on such parts.

Maytag Washer and Dryer XL Bravos - The worst machines ever. I have had many washers and dryers and every one of them were good enough to get my clothes clean and dry without wrinkles. This washer Maytag Bravos Washer and Dryerdoes not clean clothes no matter which setting it is on. The dryer does not dry the clothes without wrinkles if it dries them at all. They are only about 6 months old, I have followed the book on usage and it still doesnt help. If I could pick these up and put them at the curb I would. If Maytag would take them back I would return them. Buyer beware.Updated on 03/17/2018: Maytag wrote to me and wanted me to give them my contact information along with any other info regarding their appliances. Still havent heard from them, and I assume if I do it will be like all of the other replies, Sorry for your inconvenience yada, yada, yada. I did check online for Lemon laws for appliances and there are laws for the consumers to fight the companies. If and when they contact me I will be sure to mention this to them for what its worth. I think a class action suit might be the answer for all of us consumers. If banding together would help count me in!!!

Rather than go through all the things I dont like about this washer, just read all the complaints because that is my complaints also: bearings, not enough water in tub, clothes not getting cleaned. Just check out the lint filter and see the gray and dirty lint after a load and you will see it doesnt clean the clothes. Now, the motherboard is kaput! Cycles are all screwed up. Cost is $386 for motherboard plus labor and I will not put one more cent in this piece of crap.Listening to the salesman and consumer reports on the best washer to buy. All they are concerned with is energy savings and believe me when I say that all energy savings products are a joke because you give up operating ability for the sake of energy savings-- true of refrigerators and washers, dryers, furnaces and the like. I will be buying an agitator washing machine. The saving on water are not enough to give up clean clothes.

This Maytag bravo washing machine is the worst ever machine I have owned. I bought it new, and shortly after the 1 year warranty expired, I started having problems with it. I had a repairman come out. All he did was take out the trouble shooting guide, press a code, and wait. The machine told him that each function worked. Even though it did not work properly. He hid the trouble shooting guide inside the machine, so I cannot get to it. Now I have so many problems with this machine, that it takes me all day to do 1 load. This thing makes noises that I have never heard from a washing machine in my life. I would never buy another Maytag product, nor do I recommend anyone else to buy one.

We purchased our Maytag dishwasher less than a year ago and are very disappointed with the poorly designed quality of this product. We had a Maytag repairman look at our dishwasher and he told us that; the dishwasher cleans with enzymes in the dishwasher not water pressure, and we need to make sure the water in the kitchen faucet need to be hot before starting the dishwasher, we also need detergent, rinse aid, and citric acid added to each load. Adding all these products to the dishwasher does not fix a poorly designed product. This product does not clean the dishes, even with rinse aid the glasses come out cloudy. The dishwasher has a power blast button, it does not clean the dishes any better than the regular setting and it runs for four hours. We will never buy another Maytag product.

Seems a little ** one of a small child crawled into the washer and a sibling turned it on. We have been married 35 years and seen a lot of washers and this is by far the worst wash machine Ive ever seen. How would you rather do my wash in an old fashioned mangler? Very unsatisfied customer.

I bought the machine at Lowes. It was cheaper than the regular old agitator washers which should have been a clue. I like the old agitator washers that fill as you put in the clothes. Lowes installed it, turned it on and did not seem to care that although water should have been entering washer, none did. They rushed out. Ok, my water to the washer was bad so it was a simple plumbing fix. Less than 1 year the machine was full of water and would not agitate, spin, drain or anything. It sat full of water. My brother looked at it, fixed the hose that was no longer attached and it worked! Yeah for 1 year almost when again the belt came off, fixed again. Trying to find correct belt is starting to annoy me. I want to take it and dump it. It looks pretty but is nothing but a piece of crap. Maytag, shame on you!!!!

We bought a Maytag refrigerator about 3 years and have had so much trouble. The freezer section which is on the bottom half leaks water periodically on the floor unless, we take the bottom rack out and pry the ice from the shelf about every week. It started doing this about 6 months ago and well need to get a repair man out here. The doors on the refrigerator are also a problem. They often dont close properly, so one is partially open, but unless you look directly at it, it isnt noticeable.

I bought a brand new top/bottom refrigerator from them. 1 1/2 yrs later, the cooling stopped and had 2 repair guys come out. They replaced it with BRAND NEW refrigerator. Now 1 1/2 yrs later, the same issue is happening. ALL my food I buy goes to waste. I bought NEW so this wouldnt happen. What happened to the old fridges from back in the day! Maytag has the WORST Customer Service!!!

My Maytag fridge was purchased on 2006 and since then have had multiple service repairs. Too much freezing, not cooling at all, fan replaced. Now freezer door not sealing.I tried a few days ago to get extension on warranty but was told it had expired so I could not renew. Why wasnt I told I needed to renew back in April before it expired? I believe they are not renewing because of the history of the appliance as it has too many repairs, it will not be cost effective for the company. We have also, in the last 10 years, purchased a washer and dryer and a large screen TV and all have the same problems. What are the chances of getting all lemon appliances? Obviously we are not shopping there any longer but many people are going to have to deal with same issues we did. All the while the company keeps making money!

MF12569YEM2 - Purchased refrigerator less than 2 1/2 years ago, also started having issues with ice forming in bottom freezer and leaking on to floor. I shut the water source off to the water/ice feature, but it didnt solve the problem. After getting on this site and seeing the issue is quite widespread it seems that it should be considered a manufacturing defect. This is the second (actually third) Maytag Refrigerator we have had, one had actually needed to be replaced about 13 years ago because of electrical problem which service man said could cause it to catch fire. The replacement (different model) worked fine for about 11 years... so we decided to try Maytag again... WHAT A MISTAKE! After reading about the multiple problems we can look forward to and endless service calls I too would never purchase any Maytag or Whirlpool appliances in the future...maybe the company should think about the impact on lost consumers!

I bought a Maytag MDB7809AWW2 dishwasher two years ago. The control panel just started doing free-games. Lights would come on and off during the cleaning cycle. When selecting a cleaning cycle, some functions would be automatically selected without the capability to deselect them. It is our second and last Maytag dishwasher. Stay away from them!

I purchased a Maytag Electric Range (Model: MER7662WS1) at Lowes in February 2011. After few months, we found many rusty areas on the stainless oven door and on the stainless drawer.On 9/8, I called Maytag at 1-800-688-9900 to complain that stainless steel is not supposed to rust. A representative took the initiative to schedule A&E Factory Service to come to my house for a warranty repair, and assigned me an order # 40629499. I did not request for this service call and naturally, I regard this as a warranty service or a service of quality check of a product.On 9/19, a technician came to check the rusty area and confirmed that the stainless steel have rusted and the rust will eat through the panel. The technician called Maytag, and got the answer that Maytag will not pay for his visit because its not under warranty. The technician then checked the warranty manual, but could find not any statement that neither rust is cosmetic nor rust is not covered. The technician asked me to pay $132 for his five-minute checking service. I was so upset and called Denice at A&E Factory Service at 1-800-905-9505 to bill Maytag directly. She ignored my request and said that I should take it to Maytag.After a couple of hours waiting, holding and transferring, I explained to two Maytag customer service representatives my problem, only to get a Sorry, its not covered, its cosmetic, reply. I insisted talking to a manager and finally got Melinda at Care Solution Team. She, too, refused to waive the charge for me and claimed herself as a supervisor and decision maker and theres no one above her who could resolve this issue.I emphasized that A&E service call was authorized by Maytag, I did not order the service. Who would have thought that a service authorized by manufacturer is not covered under warranty? Besides, this representative failed to inform me that rust would not be covered, she should have known better. Therefore, I believe that the person who initiated the service call to A&E should be held accountable. But Melinda never wanted to agree with this logic and kept saying, We dont force customer to have home service. You are liable for the bill.She refused to pay for the service and forced me to pay the bill from the mistake they made. She even refused to give out the persons ID # and name of the person who called A&E. She only documented my complaint--whats the point of their documentation? If this is the tactic that Maytag is using to categorize rust as cosmetic (if rust can damage material, then you should not call it cosmetic), and ban customers from claiming the rust damage so they can use poor quality of stainless steel on their appliances to save the cost, then, it is dishonest to advertise that this oven is stainless.A representative even said that Maytag should have emailed me with the confirmation of service call and noted that its a non-warranty service. Also, A&E should have informed me before arrival that the service is not covered. All these were not true. First, I did not receive such email from Maytag or Whirlpool. If Maytag would have warned me with non-covered policy such as this, they should have the courtesy to call me in case the email was unreliably routed to spam box. A&E only informed me that they are coming the next day, but no such thing as telling me that the service will not be covered. Even their technician did not know about the non-covered issue, and had to call Maytag today to find out.Had the person who scheduled the service told me that the rust on the stainless panels is not covered under warranty, will I still allow the service call and agree to pay $132 for a five-minute checkup and watch the technician leave without performing any repair? I asked Melinda to let me talk to her supervisor but she said that theres no one who can talk to me, and the only way to appeal is to write to the companys executives. The address is: Whirlpool Corporate Office553 Benson Rd Benton Harbor, Michigan 49022. I doubt that an appeal will help me at all. I will take this matter to small claim court, I wont let them force me to pay the bill when I am not at fault.

I purchased Maytag Bravos XL Steam Washer brand new from Lowe’s in January 2018. HORRIBLE washer! Does not get clothes clean and leaves soap and scum all over clothes. I have to wash everything on power wash with an additional rinse cycle (takes about 2 hours per load) and clothes still don’t come out clean. I often have to wash a load 2 or 3 times to get it clean. Will NEVER PURCHASE another Maytag product! What is even worse is that I also bought the Maytag “commercial technology” washer at the same time. It’s an even more TERRIBLE washer. Cannot get through one cycle without getting an LF (low flow) error & the cycle shuts off and machine drains & quits. Absolutely the two WORST washers I’ve ever owned in the past 40 years!!!

I love it. Laundry as well as horse blankets. It does it all! I have never ever had one problem with it. Love the delay start setting as well as the extra rinse cycle.Easy to clean the gasket and keep the soap dispenser out to air between washes!